DSR 2018 PDF

Hkkjr ljdkj
GOVERNMENT OF INDIA
dsUnzh; yksd fuekZ.k foHkkx
CENTRAL PUBLIC WORKS DEPARTMENT
fnYyh nj vuqlwph
¼Hkkx - 2½
DELHI SCHEDULE OF RATES
(Vol. 2)
2018
egkfuns”kd] ds-yks-fu-fo-] ubZ fnYyh ds izkf/kdkj ds v/khu izdkf”kr

© All rights reserved. No part of this publication, either in English or in Hindi, may be reproduced in any form
or by any means, electronic or mechanical including photocopy, recording or any information storage and
retrieval system, without permission, in writing, from the Director General, CPWD, New Delhi.
DISCLAIMER
The rates taken in Delhi Schedule of Rates 2018 are indicative and actual rates shall be governed by the
market forces. Further its use by Govt. Departments, PSUs, private bodies & individuals shall be at their own
risk and discretion. CPWD shall not be responsible for any ambiguity, discrepancy, dispute or financial loss,
arising directly or indirectly by using or following items of DSR by such Govt./Private bodies or individuals.
For feed back and suggestions, please contact SE(TAS), CPWD, Room No. 418, ''A'' Wing, Nirman
Bhawan, New Delhi. Tel. No. 011-23062339, Email: [email protected]
A GOVERNMENT OF INDIA PUBLICATION

Published by
DIRECTOR GENERAL
CPWD, Nirman Bhawan, New Delhi - 110011
&
Printed & Marketed by
JAIN BOOK AGENCY JAIN BOOK DEPOT

Authorised Dealers of Govt. Publications C - 4, Opp. PVR Plaza, Post Box. No. 51,
C-9, Connaught Place, New Delhi-110001 Connaught Place, New Delhi-110001 (India)
Phones : 011- 44556677, 23416390 upto 94 Phone : 011- 23416101 / 02 / 03
E-mail : [email protected] E-mail : [email protected]
Website : www.jainbookagency.com
JAIN BOOK AGENCY (SOUTHEND) JAIN BOOK AGENCY (GURGAON)

1, Aurobindo Place Market, 19, Central Plaza Mall, Sector 53,
Hauz Khas, New Delhi-110016 Golf Course Road,
Phone : 011- 41755666 Gurgaon 122002 Haryana
E-mail : [email protected] Phone : 0124- 4042665
Website : www.jainbookagency.com Mobile : 9810666810
JAIN BOOK AGENCY (INTERNATIONAL) JAIN BOOK AGENCY (GREATER NOIDA)

RA- 11, Sector- 126, 11 Jagat farm Complex
Opp. Gate No. 2A of Amity University, Gama Sector Market
Noida Near OBC Bank
Mobile. : 9210080580 Greater Noida
Phone : 0120-4206655
Distributed by
JAIN BOOK AGENCY (CENTRAL)
4574/15, 2nd Floor, Padamchand Marg,
Near Happy School, Daryaganj, New Delhi-110002
Phone : 011- 43513689, 43513570
Mob: 9667274446, 9810666810
E-mail : [email protected]
Also available at
All Leading Booksellers & Authorised Govt. Dealers In India
Price : Rs. 1200/- (for both volumes) excluding postage and forwarding charges etc.
Hkkjr ljdkj dsUnzh; yksd fuekZ.k foHkkx
Government of India fuekZ.k Hkou] ubZ fnYyh 110011
Central Public Works Department
PRABHAKAR SINGH Nirman Bhawan, New Delhi- 110011
Director General Tel : 23062556 / 1317, Fax : 23061884
E-Mail : [email protected]
FOREWORD
Delhi Schedule of Rates, being published by Central Public Works
Department from time to time, is a comprehensive and useful Technical
Document in execution of Civil Construction Works. Apart from CPWD, this
Schedule of Rates is used as a guide by many Departments, Institutions,
Public Sector Undertakings, Architects, Builders and Contractors etc.
CPWD Schedule of Rates was first published in the year 1931, followed by a
number of revisions/publications from time to time in order to bring it in line
with the prevailing materials,technologies and market rates. Delhi Schedule of
Rates were revised and issued in subsequent years viz 1977,
1981, 1985, 1989, 1993, 1997, 2002, 2007, 2010 (Reprint), 2012, 2013, 2014
& 2016.
Last Delhi Schedule of Rates was published in the year 2016. Revision of this
DSR has become necessary due to change in wages of labour & price of
materials, adoption of new construction technologies & materials as well as
implementation of GST. These components have been incorporated in the
DSR 2018 by revising DSR 2016.
I wish to place on record the technical input and effective coordination on the
part of Shri A.S. Arora, ADG (S&P), Dr K M Soni ADG (TD), Shri Manu
Amitabh CE (CSQ) (Civil) and the efforts put in by Shri Divakar Agrawal SE
(TAS). Shri D.S.Panwar EE(TAS-I), Shri M L Prasad EE(TAS-II),
Shri D.S. Adhikari AE (QA), Shri Naveenkumar P JE (TAS) and team of officers
in CSQ unit in finalizing the DSR-2018 in a short time.
I am sure that Delhi Schedule of Rates 2018 will be quite useful to all
concerned Engineers & Architects in Building Construction Industry in general
and CPWD in particular.
Place: New Delhi (PRABHAKAR SINGH)

Date: December 14, 2018 Director General
Hkkjr ljdkj
Government of India
DR K.M. SONI fuekZ.k Hkou] ubZ fnYyh 110011
Addl. Director General (TD)
Nirman Bhawan, New Delhi- 110011
PREFACE
1. DSR i.e. Delhi Schedule of Rates-2018 includes the existing items of DSR 2016 with deletion of
few items not in practice, merger of similar items and addition of new items in line with emerging
trends in construction Industry.
2. DSR-2018 is based on the prevailing market rates of materials in Delhi as on 01.10.2018. The
labour rates adopted are as per minimum wages applicable w.e.f 01.10.2018 issued by Govt. of
Delhi/ Govt. of India, whichever is higher.
3. The cost index for DSR 2018 is 118 with reference to CPWD Plinth Area Rates 2012, having
base 100 as on 01.10.2012.
4. The technical sanctioning authority may decide rates of non-schedule items judiciously
based on market rates without adding cost index.
5. This DSR - 2018 shall be read along with CPWD specifications 2009 Vol.-I & II with up to date
Correction Slips.
6. Following are the Salient Features of DSR- 2018:
6.1 DSR-2018 is bilingual and in two volumes.
6.1.1 The rates of basic materials incorporated in this DSR - 2018 are considered for the materials
available in the market conforming to BIS Standards/ CPWD Specifications.
6.1.2 The effect of GST on works contracts has been incorporated in all the items.
Salient Modifications and Changes in Sub Heads:
7.1 Earth work: Item No. 2.25(a) Excavating, supplying and filling of local earth by mechanical
transport up to a lead of 5km has been added.
7.2 Reinforced Cement Concrete: Item No. 5.22B & 5.22C Steel Reinforcement for R.C.C work
ready to use “Cut bend” rebars have been added. Nomenclature of item no.5.9 modified. Item
no.5.50 to 5.57 shifted to sub head 26 i.e. New Technologies & Materials (26.73 to 26.80).
IV
7.3 Brick Work: Sub head 6- Brick work has been renamed as Masonry work.
7.4 Marble & Granite work: Sub head 8- Marble & Granite work has been renamed as Cladding
work and all the cladding items have been shifted in this sub head from other Sub heads i.e. 7.0,
9.0, 11.0 & 25.0.
7.5 Wood and PVC Work: The amendments have been made in nomenclature of Item Nos. 9.138,
9.163 & 9.164.
7.6 Roofing: The amendments have been made in nomenclatures of item Nos. 12.8 to 12.10 and
12.12 to 12.13.
7.7 Finishing: Item No.13.48A for finishing walls with 100% Premium Acrylic Emulsion paint having
VOC less than 50gm/litre and UV resistance as IS: 15489:2004 has been added.
7.8 Road Work: The nomenclature of Item No.16.81‘Providing and erecting 2.00 metre temporary
barricading at site’ has been modified.
7.9 Water Supply: Items Nos. 18.4, 18.5, 18.6 & 18.6A for Polypropylene Random Copolymer
(PP-R-C) pipes have been added.
7.10 Structural Glazing Aluminum Panel: The nomenclature of item No. 25.3 has been modified.
7.11 Item No. 26.20 & 26.21 have been shifted to sub head 14.0
8.0 New Technologies and Materials
With a view to give boost to make in India initiative of the Government, new technology items have
been added in New Technologies and Materials sub Head. These new items are included for a
period of two years and then performance shall be reviewed. Following are the items added under
this sub head:
8.1 Bamboo mat corrugated sheet (BMCS),Bamboo mat ridge cap(BMRC),false ceiling of Phenol
Bamboo mat board, wall paneling with Phenol bonded Bamboo mat board (item no.26.6 a to e ).
8.2 EPS cement sandwich light weight solid core panels (item no.26.49).
8.3 Non Asbestos fibre reinforced aerated sandwich wall/roof/floor light weight solid core panels
(item no.26.50).
8.4 GFRG items (item no.26.51 to 26.61)
8.5 Speed floor system (Item no.26.62 to 26.64).
8.6 Factory made fast track modular system (Item no.26.65 to 26.66)
V
8.7 External thermal insulation in composite system (Item no.26.67)
8.8 Precast solid cement concrete blocks and paver blocks made of C & D waste (Item no.26.68
to 26.72)
8.9 Prefab/Precast technology (Item no.26.73 to 26.80)
8.10 Scaffolding net (Item no. 26.81)
9.0 Lot of efforts has gone into the preparation of this Delhi Schedule of Rates. I convey my
deep appreciation and sincere thanks to:
Shri Manu Amitabh CE, (CSQ) ; Shri Divakar Agrawal SE, (TAS) ; Shri Sudhir Kumar
Dak SE, (C&M) ; Shri D.S Panwar EE-(TAS-I) ; Shri M.L Prasad EE-(TAS-II) ;
Shri P. Goyal EE-(TAD) ; Shri A K Sikka EE, (QA) ; Shri M.C. Singal EE, (QA) ;
Shri S N Jaiswal EE, (HQ) ; Shri Shivani Kaushal EE, (M) ; Shri Sajal Mitra EE, (CON) ;
Shri Kunwar Chandresh EE, (TLC) ; Shri D.S. Adhikari AE, (QA) ; Shri D. K. Malhotra
AE, (TAS) ; Shri Patta Madhukumar AE, (TAS) ; Shri Prabhat Kumar Srivastav AE,
(TAS) ; Shri Gurmeet Singh AE, (TAD) ; Shri H. K. Gupta AE, (M) ; Shri Mohammad
Tarik AE, (QA) ; Shri S.K. Sharma AE, (QA) ; Shri Gopal Warshney AE, (QA) ;
Shri K R Meena AE, (CON) ; Shri Ved Khurana AE, (TLC) ; Shri Jai Bhagwan AE, (M) ;
Shri Chalapaka Ramaraju JE, (TAD) ; Shri Naveenkumar P. JE, (TAS); Shri Jay Prakash
Chief Estimator (TAS) ; Shri Bhim Singh Sr. D/man (TAS) ; Shri Sanjay Singh AD, (OL) and
his team for hindi translation of DSR- 2018, Shri Yogendra Pal Singh Yadav, Dy. Architect,
O/o ADG (Arch.), Shri Gaurav Sarswat Asstt. Architect, O/o ADG (Arch.) for Graphic designing
of DSR 2018 and other officers and staff of CSQ unit whose names are not mentioned here,
for their sincere efforts made in the preparation of this document in such a short time.
Various Committees and field units, who contributed field inputs, also deserve appreciation
for their timely help.
10.0 Although due care has been taken to print the DSR- 2018 as correctly as possible, there is
possibility that some errors might have crept in inadvertently. In case, any error or omission
is noticed, it may be brought to the notice of Superintending Engineer (TAS), CPWD,
Room no. 418, ‘ A’, Nirman Bhawan, New Delhi – 110011 (Tele fax. 011-23062339 ).
And suggestions for improvement are always welcome.
(Dr K M SONI)
ADG (TD) CPWD
Note: - In case of any discrepancy between English and Hindi versions, the English version shall
be held valid.
VI
C O N T E N T S
Vol. 1
SH. No. NAME OF SUB-HEAD PAGE No.
A. BASIC RATES
0.1 HIRE CHARGES OF PLANTS & MACHINERY 2
0.2 LABOUR 6
0.3 MATERIALS 8
0.4 CARRIAGE CODES 61
B. SUB -HEADS
1. Carriage of Materials 64
2. Earth Work 72
3. Mortar 80
4. Concrete Work 83
5. Reinforced Cement Concrete 90
6. Masonry Work 105
7. Stone Work 113
8. Cladding Work 120
9. Wood and PVC Work 130
10. Steel Work 179
11. Flooring 188
12. Roofing 203
VII
C O N T E N T S
Vol. 2
13 Finishing 224
14 Repairs to Building 240
15 Dismantling and Demolishing 256
16 Road Work 264
17 Sanitary Installations 289
18 Water Supply 314
19 Drainage 357
20 Pile work 371
21 Aluminium Work 378
22 Water Proofing 385
23 Rain Water Harvesting & Tubewells 394
24 Conservation of Heritage Buildings. 400
25 Structural Glazing Aluminium Composite Panel 404
26 New Technologies and Materials 411
C. CEMENT CONSUMPTION STATEMENT 444
D. BITUMEN CONSUMPTION STATEMENT 479
Note: For Sub Heads 1 to 12 refer to Vol. 1
VIII
(Vol. 2)
fnYyh nj vuqlwph
¼Hkkx - 2½
2018
SUB HEAD : 13.0
FINISHING
224
BASIC RATES (SH: 13.0 FINISHING)
Code Description Unit Rate

No.
0006 Hire charges of spraying machines including electric charges day 250.00
0101 Bhisti day 617.00
0112 Carpenter 2nd class day 679.00
0114 Beldar day 558.00
0115 Coolie day 558.00
0117 Assistant Fitter or 2nd class Fitter day 679.00
0122 Mason (for plaster of paris work) 1st class day 738.00
0123 Mason (brick layer) 1st class day 738.00
0131 Painter day 679.00
0141 White Washer day 617.00
0155 Mason (average) day 709.00
0156 Carpenter (average) day 709.00
0324 Coal Tar litre 30.00
0367 Portland Cement (OPC-43 Grade) tonne 4940.00
0368 White Cement tonne 11200.00
0763 Glue kg 75.00
0771 Kerosene oil litre 50.00
0772 White cement based polymer modified self curing compound in
powder form kg 15.00
0775 Dehradun white lime quintal 600.00
0776 Satna lime quintal 370.00
0777 Dry hydrated lime (factory made) quintal 290.00
0801 Silicon and acrylic emulsion litre 130.00
0802 Acrylic distemper 1st quality , having VOC content less than
50 grams/ litre Kg 36.00
0803 Acrylic emulsion, having VOC content less than 50 grams/ litre litre 94.00
0804 Premium acrylic emulsion of interior grade, having VOC content
less than 50 grams/ litre litre 220.00
0806 Ready mixed pink or grey primer on wood work (hard and soft wood)
having VOC content less than 50 grams/ litre litre 105.00
0808 Water thinnable cement primer for interior wall surface, having VOC
content less than 50 grams/ litre litre 50.00
0809 Exterior primer kg 140.00
0815 Dry distemper kg 30.00
0816 Ist quality Acrylic distemper(Ready mix) having VOC content less
than 50 grams/ litre kg 50.00
0818 Linseed oil (double boiled) litre 200.00
0820 Cement primer litre 80.00
SUB HEAD : 13.0 FINISHING 225

No.
0821 Distemper primer litre 70.00

0823 Pink primer (for wood) litre 105.00
0824 White cement based putty kg 13.00
0826 Aluminium paint litre 150.00
0827 Acid proof paint (chocolate or black) litre 225.00
0828 Anticorrosive bituminous paint (black) litre 100.00
0829 Black Japan paint litre 90.00
0830 Enamel paint litre 165.00
0831 Floor enamel paint in all shades except green litre 250.00
0833 Synthetic enamel paint in black or chocolate shade litre 170.00
0834 Synthetic enamel paint in all shades except black or chocolate shade litre 160.00
0835 Plastic acrylic emulsion paint litre 200.00
0836 100% Premium acrylic dirt resistance, Silicone additives exterior paint litre 270.00
0837 Acrylic Exterior Primer litre 100.00
0850 White lead kg 170.00
0851 Water proofing cement paint kg 38.00
0855 Wax polish (ready made) kg 230.00
0856 Ordinary varnish litre 100.00
0857 Superior copal varnish litre 115.00
0858 Superior spar varnish litre 115.00
0859 Oil type wood preservative litre 130.00
0868 Premixed super white gypsum plaster kg 6.00
0869 Plaster of Paris kg 5.00
0982 Coarse sand (zone III) cum 1350.00
0999 Shellac kg 300.00
1000 Spirit litre 48.00
1179 Crushed stone 2.36 mm to 12.5 mm size cum 900.00
1198 Second class kail wood in planks 10 cudm 260.00
1213 Water proofing materials kilogram 35.00
1216 Whiting quintal 600.00
1315 C.P. Brass chain with 40mm dia rubber plug each 40.00
2202 Carriage of Stone aggregate below 40 mm nominal size cum 103.77
2203 Carriage of Coarse sand cum 103.77
2209 Carriage of Cement tonne 92.24
2911 Stone chippings/ screenings 10/ 11.2 mm nominal size cum 1150.00
4201 Aluminium primer litre 110.00
4202 Red oxide Zinc chromate primer litre 110.00
4203 Copper acetate kg 285.00

No.
4204 Hydrochloric acid kg 33.00
4205 Copper chloride kg 270.00
4206 Copper nitrate kg 210.00
4207 Ammonium chloride kg 20.00
7239 Epoxy paint litre 230.00
7240 Fire retardant paint litre 260.00
7241 Melamine Polish litre 280.00
7306 Aluminium T or L sections kg 190.00
8504 Multi surface paint litre 255.00
8505 Acrylic exterior paint litre 170.00
8506 Premium Acrylic exterior paint litre 180.00
8507 Textured exterior paint litre 240.00
8508 Primer for cement paint litre 79.00
8509 Special Primer (C.W.) litre 140.00
8510 Metal Primer (U.G.) litre 90.00
8733 Synthetic ployster triangular fibre of length 6 mm, effective
diameter 10-40 microns and specific gravity of 1.34 to 1.40 kg 400.00
9977 Carriage L.S. 2.00
9988 Carriage and sundries L.S. 2.00
9999 Sundries L.S. 2.00

13.0 FINISHING
No.
Note :- Rates for external plastic are for height upto 10m from
ground level in less otherwise stated.
CEMENT PLASTER (IN FINE SAND)
13.1 12 mm cement plaster of mix :
13.1.1 1:4 (1 cement: 4 fine sand) sqm 266.85
13.2 15 mm cement plaster on the rough side of single or half brick wall of
mix :
CEMENT PLASTER (IN COARSE SAND)
13.4.1 1:4 (1 cement: 4 coarse sand) sqm 276.15
13.5 15 mm cement plaster on rough side of single or half brick wall of
mix:
CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT
13.7 12 mm cement plaster finished with a floating coat of neat cement of
mix :
13.8 15 mm cement plaster on rough side of single or half brick wall
finished with a floating coat of neat cement of mix :
13.9 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating
coat of neat cement.
13.9.1 12 mm cement plaster sqm 350.15
13.9.2 20 mm cement plaster sqm 460.70

No.
13.10 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a

floating coat of neat cement on the rough side of single or half brick
wall. sqm 395.40
CEMENT PLASTER IN TWO COATS
13.11 18 mm cement plaster in two coats under layer 12 mm thick cement
plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm
thick cement plaster 1:6 (1 cement : 6 fine sand). sqm 399.30
13.12 18 mm cement plaster in two coats under layer 12 mm thick cement
plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick
cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with
sponge. sqm 416.55
13.13 12 mm cement plaster 1:2 (1 cement : 2 stone dust). sqm 297.30
13.14 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough
side of single or half brick wall. sqm 344.25
13.15 20 mm cement plaster 1:2 (1 cement : 2 stone dust). sqm 412.60
6MM CEMENT PLASTER
13.16.1 1:3 (1 cement : 3 fine sand) sqm 227.35
13.17 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a
floating coat of neat cement and thick coat of Lime wash on top of
walls when dry for bearing of R.C.C. slabs and beams. sqm 301.65
13.18 Neat cement punning. sqm 62.75
ROUGH CAST PLASTER
13.19 Rough cast plaster upto 10 m height above ground level with a mixture
of sand and gravel or crushed stone from 6 mm to 10 mm nominal
size, dashed over and including the fresh plaster in two layers, under
layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top
layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with
10% finely grounded hydrated lime by volume of cement.
13.19.1 Ordinary cement finish using ordinary cement sqm 681.10
PEBBLE DASH PLASTER
13.20 Pebble dash plaster upto 10 m height above ground level with a
mixture of washed pebble or crushed stone 6 mm to 12.5 mm nominal
size, dashed over and including fresh plaster in two layers under
layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top
layer 10 mm cement plaster with cement mortar 1:3 (1 cement : 3
fine sand) mixed with 10% finely grounded hydrated lime by volume
of cement. sqm 638.95
13.21 Extra for providing and mixing water proofing material in cement per bag of
plaster work in proportion recommended by the manufacturers. 50kg cement
used in the
mix 59.75
13.22 Extra for plastering exterior walls of height more than 10 m from
ground level for every additional height of 3 m or part thereof. sqm 65.95

No.
13.23 Extra for plastering on circular work not exceeding 6 m in radius:

13.23.1 In one coat sqm 35.80
13.23.2 In two coats sqm 54.45
13.24 Extra for plastering done on moulding, cornices or architraves
including neat finish to line and level:
13.24.1 In one coat sqm 532.75
13.24.2 In two coats sqm 878.40
13.25 Extra for plastering:
13.25.1 Spherical ceiling sqm 133.60
13.25.2 Groined ceiling sqm 144.75
13.25.3 Flewing soffits sqm 88.35
13.26 Providing and applying plaster of paris putty of 2 mm thickness over
plastered surface to prepare the surface even and smooth complete. sqm 196.70
ARTIFICIAL STONE PLASTER
13.27 Extra for lining out plaster to imitate stone or concrete blocks walling. sqm 85.25
PLAIN CEMENT MORTAR BANDS
13.28 12 mm thick plain cement mortar bands in cement mortar 1:4 (1
cement : 4 fine sand):
13.28.1 Flush Band cm per metre 5.70
13.28.2 Sunk Band cm per metre 6.20
13.28.3 Raised Band cm per metre 7.10
13.28.4 Moulded Band cm per metre 12.15
13.29 18 mm thick plain cement mortar band in cement mortar 1:4 (1
13.29.1 Flush Band cm per metre 6.90
13.29.2 Sunk Band cm per metre 7.60
13.29.3 Raised Band cm per metre 8.70
13.29.4 Moulded Band cm per metre 16.25
13.30 18 mm thick moulded cement mortar band in two coats under layer
12 mm thick with cement mortar 1:5 (1 cement : 5 coarse sand) top
layer 6 mm thick with cement mortar 1:4 (1 cement : 4 fine sand). cm per metre 16.20
POINTING ON BRICK WORK
13.31 Pointing on brick work or brick flooring with cement mortar 1:3 (1
13.31.1 Flush / Ruled/ Struck or weathered pointing sqm 191.55
13.31.2 Raised and cut pointing sqm 313.80
POINTING ON TILE BRICK WORK
13.32 Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine
sand):
13.32.1 Flush/ Ruled/ Struck or weathered pointing sqm 260.90

No.
POINTING ON STONE WORK

13.33 Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine
sand) :
13.33.1 Flush/ Ruled pointing sqm 285.40
13.33.2 Raised and cut pointing sqm 520.75
13.34 Raised and cut pointing on stone work in white cement mortar 1:3 (1
white cement : 3 marble dust). sqm 538.25
13.35 Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2
fine sand):
13.35.1 Flush/ Ruled pointing sqm 159.00
13.36 Extra for pointing on walls on the outside at height more than 10 m
from ground level for every additional height of 3 m or part there of. sqm 7.15
INTERIOR FINISHING
13.37 White washing with lime to give an even shade :
13.37.1 New work (three or more coats) sqm 28.55
13.38 Satna lime wash on walls with one coat. sqm 11.50
13.39 Colour washing such as green, blue or buff to give an even shade :
13.39.1 New work (two or more coats) with a base coat of white
washing with lime sqm 38.95
13.39.2 New work (two or more coats) with a base coat of whiting sqm 38.50
13.40 Distempering with dry distemper of approved brand and manufacture
(two or more coats) of required shade on new work, over and including
water thinnable priming coat to give an even shade. sqm 117.75
13.41 Distempering with oil bound washable distemper of approved brand
and manufacture to give an even shade :
13.41.1 New work (two or more coats) over and including water
thinnable priming coat with cement primer sqm 153.45
13.42 Distempering with 1st quality acrylic distemper (ready mixed)
having VOC content less than 50 gms/litre, of approved
manufacturer, of required shade and colour complete, as per
manufacturer’s specification.
13.42.1 Two or more coats on new work sqm 87.15
13.43 Applying one coat of water thinnable cement primer of approved brand
and manufacture on wall surface :
13.43.1 Water thinnable cement primer sqm 60.00
EXTERIOR FINISHING
13.44 Finishing walls with water proofing cement paint of required shade :
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm) sqm 91.25
13.45 Finishing walls with textured exterior paint of required shade :
13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm)
over and including priming coat of exterior primer applied
@ 2.20kg/10 sqm sqm 232.00

No.
13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :
13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm
@ 2.20 kg/10 sqm) sqm 164.70
13.47 Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade:
13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm
@ 2.20 kg/10 sqm) sqm 161.15
13.48 Finishing with Deluxe Multi surface paint system for interiors and
exteriors using Primer as per manufacturers specifications :
13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm
over and including one coat of Special primer applied @
0.75 ltr /10 sqm sqm 142.20
13.48.2 Painting wood work with Deluxe Multi Surface Paint of
required shade. Two or more coat applied @ 0.90 ltr/10
sqm over an under coat of primer applied @0.75 ltr/10
sqm of approved brand and manufacture sqm 130.25
13.48.3 Painting Steel work with Deluxe Multi Surface Paint to
give an even shade. Two or more coat applied @ 0.90 ltr/
10 sqm over an under coat of primer applied @ 0.80 ltr/
10 sqm of approved brand and manufacture sqm 125.80
13.48A Finishing walls with 100% Premium acrylic emulsion paint having
VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,
Alkali & fungal resistance, dirt resistance exterior paint of
required shade (Company Depot Tinted) with silicon additives.
13.48A.1 New work (Two or more coats applied @ 1.43 litre/
10 sqm. Over and including priming coat of exterior
primer applied @ 0.90 litre/10 sqm. sqm 146.20
13.50 Applying priming coat:
13.50.1 With ready mixed pink or Grey primer of approved brand
and manufacture on wood work (hard and soft wood) sqm 57.05
13.50.2 With ready mixed aluminium primer of approved brand
and manufacture on resinous wood and plywood sqm 57.55
13.50.3 With ready mixed red oxide zinc chromate primer of
approved brand and manufacture on steel galvanised iron/
steel works sqm 50.70
13.50.4 With ready mixed red oxide zinc chromate primer of
approved brand and manufacture on steel work (second
coat) sqm 27.20
13.51 Painting with silicon & acrylic emulsion based water thinnable sealer
of approved brand and manufacture on wet or patchy portion of
plastered surfaces :
13.51.1 One coat sqm 81.20
13.51.2 Two coats sqm 129.05

No.
13.52 Finishing with Epoxy paint (two or more coats) at all locations prepared
and applied as per manufacturer’s specifications including appropriate
priming coat, preparation of surface, etc. complete.
13.52.1 On steel work sqm 189.75
13.52.2 On concrete work sqm 189.40
13.53 Painting on G.S. sheet with synthetic enamel paint of approved brand
and manufacture of required colour to give an even shade :
13.53.1 New work (two or more coats) including a coat of approved
steel primer but excluding a coat of mordant solution sqm 138.00
13.54 Applying a coat of mordant solution on G.S. sheet:
13.54.1 With a solution of 38 gms of copper acetate in a litre of
soft water sqm 48.25
13.54.2 With a solution made of 13 gms of hydrochloric acid in a
solution of 13 gms each of copper chloride, copper nitrate
and ammonium chloride dissolved in a litre of soft water sqm 48.05
13.55 Painting (two or more coats) on rain water, soil waste and vent pipes
and fittings with black anticorrosive bitumastic paint of approved brand
and manufacture, over and including a priming of ready mixed zinc
chromate yellow primer on new work:
13.55.1 100 mm diameter pipes metre 58.15
and fittings with synthetic enamel paint of approved brand and
manufacture and required colour over a priming coat of approved
steel primer on new work.
13.57 Painting with oil type wood preservative of approved brand and
manufacture :
13.57.1 New work (two or more coats) sqm 44.50
13.58 Providing and applying two coats of fire retardant paint on cleaned
wood / ply surface @ 3.5 sqm per litre per coat including preparation
of base surface as per recommendations of manufacturer to make
the surface fire retardant. sqm 292.00
13.59 Coal tarring two coats on new work using 0.16 Litre and 0.12 litre
coal tar per sqm in the first coat and second coat respectively. sqm 50.30
13.60 Wall painting with acrylic emulsion paint of approved brand and
manufacture to give an even shade :
13.61 Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade :

No.

manufacture of required colour to give an even shade :
13.62.1 Two or more coats on new work over an under coat of
suitable shade with ordinary paint of approved brand and
manufacture sqm 177.15
13.63 Painting with aluminium paint of approved brand and manufacture to
give an even shade .
13.64 Painting with acid proof paint of approved brand and manufacture of
required colour to give an even shade :
13.65 Painting with black anti-corrosive bitumastic paint of approved brand
13.66 Floor painting with floor enamel paint of approved brand and
13.67 Varnishing with varnish of approved brand and manufacture :
13.67.1 Two or more coats of glue sizing with copal varnish over
an under coat of flatting varnish sqm 182.40
13.67.2 Two or more coats glue sizing with spar varnish or an
under coat of flatting varnish sqm 183.25
13.68 French spirit polishing :
13.68.1 Two or more coats on new works including a coat of
wood filler sqm 351.15
13.69 Polishing on wood work with ready mixed wax polish of approved
brand and manufacture :
13.69.1 New work sqm 150.90
13.70 Floor polishing on masonry or concrete floors with wax polish of
approved brand and manufacture. sqm 72.85
13.71 Lettering with black Japan paint of approved brand and manufacture per letter
per cm height 4.70
13.72 Washed stone grit plaster on exterior walls height upto 10 metre
above ground level, in two layers, under layer 12 mm cement plaster
1:4 (1 cement : 4 coarse sand ), furrowing the under layer with
scratching tool, applying cement slurry on the under layer @ 2 Kg of
cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2
(1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size),
in panels with groove all around as per approved pattern, including
scrubbing and washing the top layer with brushes and water to expose
the stone chippings ,complete as per specification and direction of
Engineer-in-charge (payment for providing grooves shall be made
separately). sqm 896.75

No.
13.73 Forming groove of uniform size in the top layer of washed stone grit
plaster as per approved pattern using wooden battens, nailed to the
under layer, including removal of wooden battens, repair to the edges
of panels and finishing the groove complete as per specifications
and direction of the Engineer-in-charge :
13.73.1 15 mm wide and 15 mm deep groove metre 57.15
13.73.2 20 mm wide and 15 mm deep groove metre 57.75
13.74 Extra for washed grit plaster on exterior walls of height more than
10 m from ground level for every additional height of 3 m or part
thereof. sqm 129.65
13.75 Extra for washed stone grit plaster on circular work not exceeding
6 m in radius (in two coats). sqm 101.10
13.76 Forming groove of uniform size from 12x12 mm and upto 25x15 mm
in the top layer of washed stone grit plastered surface as per approved
pattern, including providing and fixing aluminum channels of
appropriate size and thickness (not less than 2 mm), nailed to the
under layer with rust proof screws and nails and finishing the groove
complete as per specifications and direction of the Engineer-in-
Charge. metre 86.75
13.77 Extra for using white cement in place of ordinary cement in the top
layer of the item of washed stone grit plaster. sqm 83.75
13.78 Providing and applying 12 mm thick (average) premixed formulated
one coat gypsum lightweight plaster having additives and light weight
aggregates as vermiculite/ perlite respectively conforming to IS: 2547
(Part - 1 & II) 1976, applied on hacked / uneven background such as
bare brick/ block/ RCC work on walls & ceiling at all floors and
locations, finished in smooth line and level etc. complete. sqm 342.85
13.79 Extra for addition of synthetic Polyester triangular fibre of length 6
mm, effective diameter 10-40 microns and specific gravity of 1.34 to
1.40 in cement plaster/mortar by using 125 gms. of synthetic per bag of
Polyester triangular fibre for 50 Kgs. cement used in cement mortar 50kg of
as per directions of Engineer-in-Charge. cement 66.90
13.80 Providing and applying white cement based putty of average thickness
1 mm, of approved brand and manufacturer, over the plastered wall
surface to prepare the surface even and smooth complete. sqm 115.15
13.81 Distempering with 1st quality acrylic distemper, having VOC (Volatile
Organic Compound ) content less than 50 grams/ litre, of approved
brand and manufacture, including applying additional coats wherever
required, to achieve even shade and colour.
13.81.1 One coat sqm 50.60
13.81.2 Two coats sqm 81.90

No.
13.82 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic
Compound ) content less than 50 grams/ litre, of approved brand and
manufacture, including applying additional coats wherever required,
to achieve even shade and colour.
13.82.1 One coat sqm 71.80
13.82.2 Two coats sqm 106.80
13.83 Wall painting with premium acrylic emulsion paint of interior grade,
having VOC (Volatile Organic Compound ) content less than 50
grams/ litre of approved brand and manufacture, including applying
additional coats wherever required to achieve even shade and colour.
13.83.1 One coat sqm 75.10
13.83.2 Two coats sqm 113.90
13.84 DELETED
13.84.1 DELETED
13.84.2 DELETED
13.85 Applying priming coats with primer of approved brand and
manufacture, having low VOC (Volatile Organic Compound ) content.
13.85.1 With ready mixed pink or grey primer on wood work
(hard and soft wood) having VOC content less than 50
grams/ litre sqm 57.05
13.85.2 DELETED
13.85.3 With water thinnable cement primer on wall surface
having VOC content less than 50 grams/litre sqm 60.00
13.86 6 mm plaster on cement concrete or reinforced cement concrete
work with white cement based polymer modified self curing mortar of
approved make as per the direction of Engineer-In-Charge. sqm 205.50
13.87 White washing with lime to give an even shade :
13.87.1 Old work (two or more coats) sqm 16.75
13.87.2 Old work (one or more coats) sqm 10.25
13.88 Removing white or colour wash by scrapping and sand papering and
preparing the surface smooth including necessary repairs to scratches
etc. complete sqm 14.20
13.89 Distempering with dry distemper of approved brand and manufacture
(one or more coats) and of required shade on old work to give an
even shade. sqm 49.55
13.90 Distempering with 1st quality acrylic distember (Ready mix)
having VOC content less than 50 grams/ litre of approved brand
13.91 Removing dry or oil bound distemper, water proofing cement paint
and the like by scrapping, sand papering and preparing the surface
smooth including necessary repairs to scratches etc. complete. sqm 18.25

No.
13.92 Painting on G.S. sheet with synthetic enamel paint of approved brand
and manufacture of required colour to give an even shade :
13.93 Painting (two or more coats) on rain water, soil, waste and vent
pipes and fittings with black anticorrosive bitumastic paint of approved
brand and manufacture over and including a priming coat of ready
mixed zinc chromate yellow primer on new work :
13.94 Painting (one or more coats) on rain water, soil waste and vent pipes
and fittings with black anticorrosive bitumastic paint of approved brand
and manufacture on old work :
and fittings with aluminium paint of approved brand and manufacture
over a priming coat of ready mixed zinc chromate yellow primer on
new work :
13.96 Painting (one or more coats) on rain water, soil waste and vent pipes
and fittings with synthetic enamel paint of approved brand and
manufacture and required colour on old work :
13.97 Painting with oil type wood preservative of approved brand and
manufacture:
13.98 Wall painting with plastic emulsion paint of approved brand and
manufacture to give an even shade:
13.98.1 One or more coats on old work sqm 84.65
13.100 Painting with aluminium paint of approved brand and manufacture to
give an even shade:

No.
13.101 Painting with acid proof paint of approved brand and manufacture of
required colour to give an even shade :
13.102 Painting with black anti-corrosive bitumastic paint of approved brand
13.103 French spirit polishing :
13.104 Polishing on wood work with ready made wax polish of approved
brand and manufacture :
13.104.1 Old work sqm 76.30
13.105 Re-lettering with black Japan paint of approved brand and manufacture. per letter
per cm
height 3.00
13.106 Painting (one or more coats) with black Japan paint of approved
brand and manufacture to give an even shade. sqm 72.45
13.107 Providing and fixing C.P. brass chain and rubber plug complete for
sink or wash basin:
13.107.1 32 mm dia each 75.10
13.107.2 40 mm dia each 75.10
13.108 Distempering with 1st quality acrylic distemper (ready made) having
VOC content less than 50 gm per ltr. of approved manufacturer
and of required shade and colour complete. as per manufacturer’s
specification.
13.109 Finishing walls with water proofing cement paint of required shade :
13.109.1 Old work (one or more coats applied @ 2.20 kg/10 sqm)
over priming coat of primer applied @ 0.80 litrs/10 sqm
complete including cost of Priming coat. sqm 87.20
13.109.2 Old work (one or more coats @ 2.20 kg/10 sqm)
complete. sqm 59.35
13.110 Finishing walls with textured exterior paint of required shade :
13.110.1 Old work (Two or more coats on existing cement paint
surface applied @ 3.28 ltr/10 sqm. sqm 168.75
13.110.2 Old work (One or more coats) applied @ 1.82 ltr/10 sqm. sqm 105.30
13.111 Finishing walls with Acrylic Smooth exterior paint of required shade :
13.111.1 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm)
on existing cement paint surface sqm 99.90
13.111.2 Old work (One or more coat applied @ 0.90 ltr/10 sqm). sqm 67.35

No.
13.112 Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade
13.112.1 Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm)
over existing cement paint surface sqm 97.75
13.112.2 Old work (one or more coats applied @ 0.83 ltr/10 sqm). sqm 66.95
13.113 Varnishing with varnish of approved brand and manufacture:
13.113.1 One or more coats with copal varnish sqm 73.40
13.113.2 One or more coats with spar varnish sqm 73.85
13.114 Melamine polishing on wood work (one or more coat). sqm 110.75
13.115 Varnishing with flatting varnish of approved brand and manufacture
one or more coats on old work. sqm 76.65
Note: Item no 13.87 to 13.115 are brought from Sub Head 14
i.e. Repairs to Building Item no 14.42 to 14.71

SUB HEAD : 14.0
REPAIRS TO BUILDING
240
BASIC RATES (SH: 14.0 REPAIRS TO BUILDING)

No.
0006 Hire charges of Spraying machine including electric charges day 250.00
0011 Hire charges of Pump set of capacity 4000 litres/hour day 700.00
0058 Air compressor hour 200.00
0085 Using cost of Ultra Violet Radiation tube Hour 189.00
0086 Compressor, gun, rubber pipes & other accessories- hire charge
of plant & machinery i/c necessary fuel day 4000.00
0087 Hire Charges of Suction Jeting machine 2200 PSI machine i/c POL
and operator day 36000.00
0100 Bandhani day 617.00
0102 Blacksmith 1st class day 738.00
0103 Blacksmith 2nd class day 679.00
0111 Carpenter 1st class day 738.00
0116 Fitter (grade 1) day 738.00
0119 Glazier day 679.00
0124 Mason (brick layer) 2nd class day 679.00
0126 Mason (for ornamental stone work) 1st class day 738.00
0128 Mate day 617.00
0129 Sewer man day 558.00
0130 Mistry day 738.00
0138 Sprayer (for bitumen, tar etc.) day 617.00
0139 Skilled Beldar (for floor rubbing etc.) day 617.00
0159 Skilled torch operator for laying tack day 738.00
0160 Technician day 775.00
0164 Security guard without gun (8 hours shift duty per day) day 617.00
0165 Security guard with gun (8 hours shift duty per day) day 679.00
0295 Stone Aggregate (Single size) : 20 mm nominal size cum 1350.00
0302 Safeda ballies 125 mm diameter metre 40.00
0308 Bhusa quintal 500.00
SUB HEAD : 14.0 REPAIRS TO BUILDING 241

No.
0313 Blown type petroleum bitumen of penetration 85/25 of approved quality tonne 34000.00
0316 Bitumen solution primer of approved quality litre 45.00
0370 Coal (stream) quintal 440.00
0389 Brass single acting spring hinges 150 mm each 425.00
0392 Brass double acting spring hinges 150 mm each 480.00
0404 Brass flush bolt 250 mm each 150.00
0417 Brass 150 mm floor door stopper weighing not less than
0.357kg each 160.00
0418 Brass hard drawn hooks and eyes 300 mm 10 Nos 600.00
0423 Brass casement window fastener each 45.00
0427 Brass quadrant stays 300 mm each 110.00
0428 Brass fanlight catch 10 Nos 170.00
0429 Brass fanlight pivot 10 Nos 168.00
0430 Brass chain with hook for fan light catch each 36.00
0442 Brass helical spring 150 mm each 290.00
0444 Brass curtain rod 20 mm dia 1.25 mm thick metre 140.00
0446 Brass brackets (curtain rods) 20 mm each 45.00
0449 Brass screws 50 mm 100 Nos 220.00
0524 Chromium plated Brass butt hinges (heavy) type 75x65x
4 mm weighing not less than 200gms 10 Nos 905.00
0525 Chromium plated Brass butt hinges (light/ordinary) type
125x70x4mm 10 Nos 805.00
100x70x4 mm 10 Nos 690.00
75x40x2.5 mm 10 Nos 421.00
50x40x2.5 mm 10 Nos 180.00

No.
0585 Chromium plated Brass screws 50 mm 100 Nos 300.00

0595 Bright finished or black enameled mild steel butt hinges
100x58x 1.90 mm 10 Nos 80.00
50x37x 1.50 mm 10 Nos 49.00
0608 Nickel plated bright finished mild steel piano hinges 1 mm thick
25 mm wide metre 39.00
0637 Bright finished or black enameled mild steel screws 40 mm 100 Nos 60.00
0761 Fuel wood quintal 500.00
0772 White cement based polymer modified self curing compound
in powder form kg 15.00
0811 Mud (dry) cum 165.00
0816 Ist quality Acrylic distemper(Ready mix) having VOC content
less than 50 grams/ litre kg 50.00
0845 Roofing paint for iron sheets in red colour litre 120.00
0863 Putty for wood work kg 30.00

No.
1003 Mild steel round bar above 12 mm dia quintal 4400.00
1007 Structural steel such as tees, angles channels and R.S. joists quintal 4600.00
1008 Flats up to 10 mm in thickness quintal 4500.00
1023 Galvanised steel J or L hooks 8 mm dia 10 Nos 120.00
1034 Bolts and nuts up to 300 mm in length quintal 4800.00
1174 Red sand stone slab 45 mm to 50 mm thick (un-dressed) sqm 225.00
1186 Superior class teak wood such as Dandeli, Balarshah or Malabar
in planks 10 cudm 1100.00
1188 First class teak wood in planks 10 cudm 850.00
1189 Second class teak wood in scantling 10 cudm 776.00
1190 Second class teak wood in planks 10 cudm 791.00
1194 Second class deodar wood in planks 10 cudm 500.00
1196 First class kail wood in planks 10 cudm 300.00
1199 Sal wood in scantling 10 cudm 600.00
1208 Bitumen washer 100 Nos 30.00
1209 G.I. plain washer thick 100 Nos 35.00
1215 Welding by electric plant cm 2.00
1241 Commercial LPG in Cylinder kg 82.00
1301 Bleaching powder quintal 1800.00
1314 C.P.brass chain with 32 mm dia rubber plug each 40.00
1880 Dismenteled P or S trap scrap (approx wt 2kg) kg 22.00
1890 Centrifugally SCI(spun) S & S P or S trap each 300.00
1953 Vitreous china Indian type W.C. pan of size 580 mm each 450.00
1954 Vitreous china orrisa type W.C. pan of size 580 mm each 1200.00
1970 Vitreous china foot rests 250x125x25 mm pair 100.00
2200 Carriage of steam coal tonne 120.00
2201 Carriage of Bricks 1000 Nos 276.72
2204 Carriage of Timber cum 118.59
2205 Carriage of Steel tonne 92.24
2211 Carriage of Tar/ Bitumen tonne 103.77
2216 Carriage of Stone blocks white & red sand stone & kota stone slab tonne 92.24
2264 Carriage of Rubbish cum 103.77
2406 Float glass panes of nominal thickness 4 mm (weight not less
than 10 kg/sqm) sqm 300.00
than 12.50 kg/sqm) sqm 500.00

No.
2466 Hollock wood in scantling 10 cudm 350.00

2467 Chromium plated Brass pull bolt lock (locking bolt) of size
85 mm x 42 mm with screws, bolts, nuts and washers complete each 165.00
2602 Common burnt clay F.P.S. (non modular) bricks class designation 1000 Nos 4500.00
4009 Mild steel tubes hot finished welded type kg 57.00
7019 Dash fastener / Chemical fastener each 14.00
7241 Melamine polish litre 280.00
7346 Double coupler each 46.00
7387 Spigot for standard jointing kg 43.00
7397 Base Jack each 145.00
7398 Challies each 765.00
7399 Cup locks each 48.00
7442 Wheel 75 mm dia. 40 mm wide each 62.00
7752 PVC slotted pipe 200 mm dia as per IS: 12818 metre 840.00
8200 A.P.P. modified polymeric felt (two layers) 1.5mm thick sqm 80.00
8201 A.P.P. modified polymeric felt (two layers) 2mm thick sqm 100.00
8203 A.P.P. modified 2 mm thick membrane reinforced with glass fibre malt sqm 126.67
8204 A.P.P. modified 3 mm thick membrane reinforced with glass fible matt sqm 190.00
8205 A.P.P. modified 3 mm thick membrane with polyester matt sqm 205.00
8206 Bitumen primer for bitumen membrane litre 80.00
8207 Geotextile 120 grams per sqm membrane sqm 45.00
8500 Water for jetting / blowback 1000 litre 1500.00

14.0 REPAIRS TO BUILDING
No.
14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of area
2.5 sq.meters and under, including cutting the patch in proper shape,
raking out joints and preparing and plastering the surface of the walls
complete, including disposal of rubbish to the dumping ground, all
complete as per direction of Engineer-in-Charge.
14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand) sqm 417.80
14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) sqm 429.60
14.2 Fixing chowkhats in existing opening including embedding chowkhats
in floors or walls cutting masonry for holdfasts, embedding hold fasts
in cement concrete blocks of size 15 x 10 x 10 cm with cement
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate
20 mm nominal size), painting two coats of approved wood preservative
to sides of chowkhats and making good the damages to walls and
floors as required complete, including disposal of rubbish to the
dumping ground, all complete as per direction of Engineer-in-Charge.
14.2.1 Door chowkhats each 1366.85
14.2.2 Window chowkhats each 858.90
14.2.3 Clerestory window chowkhats each 637.85
14.3 Fixing chowkhat in existing opening in brick/ RCC wall with dash
fasteners/Chemical fasteners of appropriate size (3 nos on each
vertical member of door chowkhat and 2 nos on each vertical member
of window chowkhats), including Cost of dash fasteners/ chemical
fastener. each 193.95
14.4 Making the opening in brick masonry including dismantling in floor
or walls by cutting masonry and making good the damages to walls,
flooring and jambs complete, to match existing surface i/c disposal
of mulba/ rubbish to the nearest municipal dumping ground, all
14.4.1 For door/ window/ clerestory window sqm 932.45
14.5 Renewing glass panes, with putty and nails wherever necessary
including racking out the old putty:
14.5.1 Float glass panes of nominal thickness 4 mm (weight
not less than 10kg/sqm) sqm 890.50
not less than 12.5kg/sqm) sqm 1184.85
14.6 Renewing glass panes, with wooden fillets wherever necessary:
14.7 Renewing glass panes and refixing existing wooden fillets:

No.
14.8 Supplying and fixing new wooden fillets wherever necessary:

14.8.1 2nd class teak wood fillets metre 61.50
14.8.2 Hollock wood fillets metre 54.70
14.9 Renewal of old putty of glass panes (length) metre 42.60
14.10 Refixing old glass panes with putty and nails sqm 554.05
14.11 Fixing old glass panes with wooden fillets (excluding cost of fillets) sqm 510.75
14.12 Providing and fixing 16 mm M.S. Fan clamps of standard shape and
size in existing R.C.C. slab, including cutting chase, anchoring clamp
to reinforcement bar, including cleaning, refilling, making good the
chase with matching concrete, plastering and painting the exposed
portion of the clamps complete. each 425.10
14.13 Regrading terracing of mud phaska covered with tiles or brick, in cement
mortar by dismantling tiles or bricks, removing mud plaster, preparing
the surface of mud phaska to proper slope, relaying mud plaster gobri
leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3
fine sand), including replacing unserviceable tiles or bricks with new
ones and disposal of unserviceable material to the dumping
ground (the cost of the new tiles or brick excluded), all complete as
per direction of Engineer-in-Charge. sqm 521.60
14.14 Replacing sand stone slabs in roofing, laid in cement mortar 1:4 (1
cement : 4 coarse sand), including necessary repairs and cement
pointing with same mortar complete, including disposal of rubbish to
14.14.1 Red/ white sand stone slabs 30 to 50 mm thick sqm 957.70
14.15 Renewing wooden battens in roofs, including making good the holes
in wall and painting with oil type wood preservative of approved brand
and manufacture complete, including removal of rubbish to the
14.15.1 Sal wood battens cum 91114.45
14.16 Renewing wooden beams in roofs including making good the holes
in walls and painting with oil type wood preservative of approved
brand and manufacture complete, including removal of rubbish to the
14.16.1 Not exceeding 4.00 metres in length.
14.16.1.1 Sal wood beams cum 95325.80
14.16.1.2 Hollock wood beams cum 60859.95
14.16.2 Above 4.00 metres and upto 5.00 metres length.
14.16.2.1 Sal wood beams cum 97267.00
14.16.2.2 Hollock wood beams cum 62765.35
14.17 Raking out joints in lime or cement mortar and preparing the surface
for re-pointing or replastering, including disposal of rubbish to the
dumping ground, all complete as per direction of Engineer-in-Charge. sqm 51.70

No.
14.18 Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed
with 2% of integral water proofing compound by weight of cement for
flat tile bricks on top of mud phaska :
14.18.1 With F.P.S. brick tiles sqm 103.45
14.18.2 With modular brick tiles sqm 104.65
14.19 Taking out wind ties from roof including cutting out rusted bolts, nuts
etc. and removing materials to any distance within compound and
stacking. kg 4.00
14.20 Fixing of old wind tie with new fittings including painting two or more
coats with anticorrosive bitumastic paint of approved brand &
manufacturer over and including priming coat of ready mixed zinc
chromate yellow primer of approved brand. metre 102.60
14.21 Renewing bottom rail and/or top runner of collapsible gate including
making good all damages and applying priming coat of zinc chromate
yellow primer of approved brand and manufacturer. kg 224.60
14.22 Renewing Wrought iron or M.S. Wheel or roller of steel door or gate
and fitting and fixing the same with necessary clamps, nuts and
bolts/welding and erection etc. complete.
14.22.1 Wheel 50 mm dia and below per wheel 146.75
14.22.2 Wheel above 50 mm dia per wheel 240.45
EARTH WORK
14.23 Pumping out water caused by springs, tidal or river seepage, broken
water mains or drains and the like. kilo litre 169.05
14.24 Mud mortar made with local clay good earth. cum 737.00
BRICK WORK
14.25 Brick work with common burnt clay bricks of class designation 7.5
in mud mortar cum 5281.35
WOOD WORK
14.26 Providing and fixing 25 mm thick shutters for cup board etc. :
14.26.1 Panelled or panelled & glazed shutters :
14.26.1.1 Superior class teak wood including nickel
plated bright finished M.S. piano hinges with
necessary screws. sqm 4456.60
14.26.1.2 Ist class teak wood including nickel plated
bright finished M.S. piano hinges with
14.26.2 Glazed shutters :
14.26.2.1 Superior class teak wood including nickel
plated bright finished M.S. piano hinges with
14.26.2.2 Ist class teak wood including nickel plated
bright finished M.S. piano hinges with

No.
14.27 Providing and fixing plain jaffri door and window shutters including
bright or/and black enamelled M.S. butt hinges with necessary screws
35x10 mm laths placed 35 mm apart (frames to be paid separately),
including fixing 50x12 mm beading complete with :
14.27.1 Second class teak wood sqm 4069.70
14.28 Providing and fixing brass curtain rods of wall thickness 1.25 mm
with two brass brackets fixed with brass screws and wooden plugs
etc. wherever necessary complete.
14.28.1 20 mm diameter. metre 292.90
14.28.2 25 mm diameter. metre 359.80
14.29 Providing and fixing M.S. round or square bars with M.S. flats at
required spacing in wooden frames of windows and clerestory windows. kg 92.05
14.30 Providing joists (karries) including hoisting, fixing in position and
applying wood preservative on unexposed surface etc. complete
with :
14.30.1 Sal wood cum 90056.65
14.30.2 Hollock wood cum 55939.25
14.31 Providing and fixing bright finished brass single acting spring hinges
with necessary brass screws etc. complete :
14.31.1 150 mm each 647.55
14.31.2 125 mm each 460.25
14.31.3 100 mm each 408.10
14.32 Providing and fixing bright finished brass double acting spring hinges
with necessary brass screws etc. complete :
14.32.1 150 mm each 721.15
14.32.2 125 mm each 614.10
14.32.3 100 mm each 595.40
14.33 Providing and fixing bright finished brass flush bolts with necessary
brass screws etc. complete :
14.33.1 250 mm each 229.45
14.33.2 150 mm each 199.50
14.33.3 100 mm each 145.95
14.34 Providing and fixing 150 mm bright finished floor brass door stopper
with rubber cushion, necessary brass screws etc. to suit shutter
thickness complete each 232.50
14.35 Providing and fixing bright finished brass hard drawn hooks and eyes :
14.35.1 300 mm each 86.45
14.35.2 250 mm each 82.95
14.35.3 200 mm each 74.40
14.35.4 150 mm each 59.70
14.35.5 100 mm each 52.35

No.
14.36 Providing and fixing bright finished brass fan light pivot with necessary
brass screws etc. complete. each 39.70
14.37 Providing and fixing 300 mm long bright finished brass chain with
hook for fan light including necessary brass screws etc. complete. each 63.65
14.38 Providing and fixing bright finished brass quadrant stay 300 mm long
with necessary brass screws etc. complete. each 162.65
14.39 Providing and fixing bright finished brass helical door spring (superior
quality). each 457.90
14.40 Providing and fixing chromium plated brass butt hinges with necessary
chromium plated brass screws etc. complete.
14.40.1 125x70x4 mm (ordinary type) each 170.10
14.40.3 75x65x4 mm (heavy type) each 162.15
14.40.4 75x40x2.5 mm (ordinary type) each 97.35
14.41 Providing and fixing 85x42 mm chromium plated brass pull bolt
lock with necessary chromium plated brass screws, nuts, bolts and
washers etc. complete. each 245.20
FINISHING
14.42 Item Shifted to Sub Head 13 as item 13.87

No.

14.72 Providing and fixing double scaffolding system (cup lock type) on
the exterior side, up to seven story height made with 40 mm dia
M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining
with cup & lock system with M.S. tubes, M.S. tube challies, M.S.
clamps and M.S. staircase system in the scaffolding for working
platform etc. and maintaining it in a serviceable condition for the
required duration as approved and removing it there after .The
scaffolding system shall be stiffened with bracings, runners,
connection with the building etc wherever required for inspection of
work at required locations with essential safety features for the
workmen etc. complete as per directions and approval of Engineer-
in-charge .The elevational area of the scaffolding shall be measured
for payment purpose .The payment will be made once irrespective of
duration of scaffolding. sqm 257.95
Note: - This item to be used for maintenance work judicially,
necessary deduction for scaffolding in the existing item to be done.
14.73 Providing and fixing bright finished brass casement window fasteners
or peg stays to windows/ ventilators with necessary welding and
machine screws etc. complete. kg 473.90
14.74 Providing and fixing 14 mm bright finished brass spring catch to
steel centre hung ventilators with necessary welding and machine
screws etc. complete. each 57.30
14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5
sqm and under, including cutting the patch in proper shape, raking
out joints and preparing plastering the wall surface with white cement
based polymer modified self curing mortar, including disposal of
rubbish, all complete as per the direction of Engineer-In-Charge. sqm 512.00
ROUTINE MAINTENANCE WORK
14.75A Cleaning of terrace/loft water storage tank (inside surface area) upto
2000 litre capacity at all heights with coconut brushes, duster etc.,
removal of silt, rubbish from the tank and cleaning the tank with fresh
water disinfecting with bleaching powder @ 0.5gm per litre capacity
of tank including marking the date of cleaning on the side of tank
body with the help of stencil and paint and disposing of malba all
complete as per direction of Engineer-in-Charge. (The old date already
written on tank should be removed with paint remover or black paint

No.
and if date is not written with the stencil or old date is not removed
deduction will be made @ Rs. 0.10 per litre) (if during cleaning any
GI fittings or ball cock is damaged that is to be repaired by contractor
at his own cost and nothing extra will be paid on this account) litre 0.35
14.76 Cleaning and desilting of gully trap chamber, including removal of
rubbish mixed with earth etc. and disposal of same, all as per the
direction of Engineer-in-charge. each 77.65
14.77 Cleaning of chocked sewer line by diesel running vehicle mounting
hydraulic operated high pressure suction cum jetting sewer cleaning
machine fitted with pump having 4000 litres suction capacity and
6000 litres water jetting tank capacity including skilled operator,
supervising engineer etc. for cleaning and partial desilting of manholes
and dechocking of sewer lines. Dechocking and flushing of sewer
line from one manhole to another by high pressure jetting system of
2200 PSI for sewer line from 150mm dia upto 300mm metre 256.90
14.78 Cleaning of under ground sump, Over Head R.C.C. Tank ( independent
staging) including disposal of slit and rubbish, all as per direction of
Engineer-in-Charge. The cleaning shall consist following operations:-
(i)Tank shall be emptied of water by pumping & bottom shall be
cleaned of silt and other deposits.
(ii) Entire surface area of the sump shall then scrubbed thoroughly
with wire brush etc. and pressure washed with water.
(iii) Chlorination of RCC internal surface by liquid chlorine.
(iv) The treated surface shall be dried using air jetting and all loose
particles shall be removal from the surface.
(v) Finally the surface shall be treated with ultraviolet radiation etc.
as per direction of Engineer-in-Charge. sqm 63.70
14.79 Disconnecting damaged overhead/terrace PVC water storage tank
of any size from water supply line and removing from the terrace
including shifting at ground level as per direction of Engineer-in- charge. each 317.75
14.80 Providing & fixing White vitreous china water closet squatting pan
(Indian type) along with “S” or “P” trap including dismantling of old
WC seat and “S” or “P” trap at site complete with all operations
including all necessary materials, labour and disposal of dismantled
material i/c malba, all complete as per the direction of Engineer-in
charge.
14.80.1 Long pattern W.C Pan of size 580x440 mm each 2724.10
14.80.2 Orissa pattern W.C Pan of size 580x440 mm each 3537.80
14.81 Cutting holes of required size in brick masonry wall for fixing of exhaust
fan including providing and fixing 300 mm dia PVC pipe conforming
BIS-12818 and making good the same etc. complete as per direction
of Engineer-in-charge. each 220.40
14.82 Dismantling W.C. Pan of all sizes including disposal of dismantled
materials i/c malba all complete as per directions of Engineer-in-
Charge. each 96.00

No.
14.83 Hacking of CC flooring including cleaning for surface etc. complete

as per direction of the Engineer-in-Charge. sqm 2.50
14.84 Dismantling 15 to 40 mm dia G.I. pipe including stacking of
dismantled pipes (within 50 metres lead) as per direction of Engineer-
in-Charge.
(a) Internal Work- Exposed on wall metre 2.70
14.85 Taking out existing wooden door shutter, repair by cutting, painting
etc. and refixing of repaired door shutters to existing door frames,
including replacement of hinges with screws, etc. as required, all
complete as per the direction of the Engineer-in-charge. each 297.85
14.86 Providing and laying in situ seven course water proofing treatment
with APP (Atactic poly-propylene) modified Polymeric memberane
over roof consisting of first coat of bitumen primer @ 0.40 litre per
sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm,
which shall consist of blown type bitumen of grade 85/25 conforming
to IS : 702, 3rd and 5th layers of roofing membrane APP modified
Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting
of five layers prefabricated with centre core as 20 micron HMHDPE
film sandwiched on both sides with polymeric mix and the polymeric
mix is protected on both side with 20 micron HMHDPE film. 7th, the
top most layer shall be finished with brick tiles of class designation
10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed
with 2% integral water proofing compound by weight of cement over
a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for separately). sqm 592.65
14.87 Providing and laying in situ five course water proofing treatment with
APP (Atactic Polypropylene) modified Polymeric memberane over
roof consisting of first coat of bitumen primer @ 0.40 litre per sqm,
2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall
consist of blown type bitumen of grade 85/25 conforming to IS : 702,
3rd layer of roofing membrane APP modified Polymeric membrane
2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers
prefabricated with centre core as 100 micron HMHDPE film
sandwiched on both sides with polymeric mix and the polymeric mix
is protected on both side with 20 micron HMHDPE film. 5th, the top
most layer shall be finished with brick tiles of class designation 10
grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with
2% integral water proofing compound by weight of cement over a 12
mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished
neat (item of laying brick tiles shall be paid for separately). sqm 408.75
14.88 Providing and laying in situ seven course water proofing treatment
with APP (Atactic Polypropylene) modified Polymeric memberane
over roof consisting of first coat of bitumen primer @ 0.40 litre per
sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 kg/sqm,
which shall consist of blown type bitumen of grade 85/25 conforming
to IS : 702, 3rd and 5th layers of roofing membrane APP modified
Polymeric membrane 2.0 mm thick of 3.00 Kg/sqm weight consisting
of five layers prefabricated with centre core as 100 micron HMHDPE
film sandwiched on both sides with polymeric mix and the polymeric

No.
mix is protected on both side with 20 micron HMHDPE film. 7th, the
top most layer shall be finished with brick tiles of class designation
10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed
with 2% integral water proofing compound by weight of cement over
a 12 mm layer of cement mortar 1:3 ( 1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for separately). sqm 651.50
14.89 Providing and fixing APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 2 mm thick water proofing membrane , black
finished reinforced with glass fibre matt consisting of a coat of bitumen
primer for bitumen membrane @ 0.40 litre/sqm by the same
membrance manufacture of density at 25°C, 0.87 - 0.89 kg/ litre and
viscocity 70 - 160 cps. Over the primer coat the layer of membrane
shall be laid using Butane torch and sealing all joints etc., and
preparing the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23°C as 350/300 N/ 5 cm.
Tear strength in longitudinal and transverse direction as 60/80N.
Softening point of membrane not less than 150°C. Cold flexibility
shall be upto -2°C when tested in accordance with ASTM, D - 5147.
The laying of membrane shall be got done through the authorised
applicator of the manufacture of membrane.
14.89.1 2mm (for corrugated roof sheets) sqm 419.75
14.90 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer, 3 mm thick water proofing membrane, black
finished reinforced with glass fibre matt consisting of a coat of bitumen
primer for bitumen membrane @ 0.40 litre/sqm by the same
membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and
viscocity 70 - 160 cps. Over the primer coat the layer of membrane
shall be laid using butane torch and sealing all joints etc., and
preparing the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23°C as 350/300 N/5 cm.
Tear strength in longitudinal and transverse direction as 60/80N.
Softening point of membrane not less than 150°C. Cold flexibility
shall be upto -2°C when tested in accordance with ASTM, D - 5147.
The laying of membrane shall be got done through the authorised
applicator of the manufacturer of membrane :
14.90.1 3 mm thick sqm 512.95
14.91 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 3 mm thick water proofing membrane, black
finished reinforced with non-woven polyester matt consisting of a
coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by
the same membrane manufacture of density at 25°C, 0.87-0.89 kg/
litre and viscocity 70-160 cps. Over the primer coat the layer of
membrane shall be laid using Butane Torch and sealing all joints
etc, and preparing the surface complete. The vital physical and
chemical parameters of the membrane shall be as under : Joint
strength in longitudinal and transverse direction at 23°C as 650/ 450N/
5cm. Tear strength in longitudinal and transverse direction as 300/

No.
250N. Softening point of membrane not less than 150°C. Cold

flexibility shall be upto -2°C when tested in accordance with ASTM,
D - 5147. The laying of membrane shall be got done through the
authorised applicator of the manufacturer of membrane :
14.91.1 3 mm thick sqm 535.00
14.92 Extra for covering top of membrane with Geotextile, 120 gsm non
woven, 100% polyester of thickness 1 to 1.25 mm bonded to the
membrane with intermittent touch by heating the membrane by Butane
Torch as per manufactures recommendation. sqm 99.75
Note: Item no 14.86 to 14.92 are brought from Sub Head 22 i.e.
Water Proofing, Item no 22.15 to 22.21
14.93 Providing round the clock security guard without gun for watch &
ward of Government premises and its all belongings by deploying
neatly dressed security guards in 8 hour’s shift including necessary
T&P like torch, lathi and uniform etc.complete,as per the direction of
Engineer-in-charge.(One job means 8 hour’s duty). each job 732.55
14.94 Providing round the clock security guard with gun for watch & ward
of Government premises and its all belongings by deploying neatly
dressed security guards in 8 hour’s shift including necessary T&P
like torch, lathi and uniform etc.complete, as per the direction of
Engineer-in-charge.(One job means 8 hour’s duty). each job 803.85
Note: Item no 14.93 & 14.94 are brought from Sub Head 26 i.e.
New Technologies and Materials, Item no 26.20 & 26.21

SUB HEAD : 15.0
DISMANTLING
AND
DEMOLISHING
256
BASIC RATES (SH:15.0 DISMANTLING AND DEMOLISHING)

No.
0038 Tractor with ripper attachment day 1200.00

0039 Tractor with trolley day 1350.00
0040 Air compressor 250 cfm with two leads for pneumatic cutters / hammers day 1600.00
0041 Joint cutting machine with 2-3 blades day 800.00
0128 Mate day 617.00
SUB HEAD : 15.0 DISMANTLING AND DEMOLISHING 257

15.0 DISMANTLING AND DEMOLISHING
No.
15.1 Demolishing lime concrete manually/ by mechanical means and
disposal of material within 50 metres lead as per direction of Engineer-
in-charge. cum 607.50
15.2 Demolishing cement concrete manually/ by mechanical means
including disposal of material within 50 metres lead as per direction
of Engineer - in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design
mix) cum 1737.45
15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design
mix) cum 1072.80
15.3 Demolishing R.C.C. work manually/ by mechanical means including
stacking of steel bars and disposal of unserviceable material within
50 metres lead as per direction of Engineer - in- charge. cum 2534.70
15.4 Demolishing R.B. work manually/ by mechanical means including
stacking of steel bars and disposal of unserviceable material within
50 metres lead as per direction of Engineer-in- charge. cum 2267.15
15.5 Extra for cutting reinforcement bars manually/ by mechanical means
in R.C.C. or R.B. work (Payment shall be made on the cross
sectional area of R.C.C. or R.B. work) as per direction of Engineer-
in-charge. sqm 863.35
15.6 Extra for scrapping, cleaning and straightening reinforcement from
R.C.C. or R.B. work. kg 6.70
15.7 Demolishing brick work manually/ by mechanical means including
stacking of serviceable material and disposal of unserviceable material
within 50 metres lead as per direction of Engineer-in-charge.
15.7.1 In mud mortar cum 503.00
15.7.2 In lime mortar with old mughal bricks cum 1271.95
15.7.3 In lime mortar cum 607.50
15.7.4 In cement mortar cum 1469.90
15.8 Removing mortar from bricks and cleaning bricks including stacking
within a lead of 50 m (stacks of cleaned bricks shall be measured):
15.8.1 From brick work in mud mortar 1000 Nos 3354.55
15.8.2 From brick work in lime mortar 1000 Nos 3886.35
15.8.3 From brick work in cement mortar 1000 Nos 4880.90
15.9 Demolishing stone rubble masonry manually/ by mechanical means
including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead as per direction of
Engineer-in-charge :

No.
15.10 Dismantling dressed stone work ashlar face stone work, marble work
or precast concrete work manually/ by mechanical means including
stacking of serviceable and disposal of unserviceable material within
50 metres lead as per direction of Engineer-in-charge :
15.11 Removing mortar from and cleaning stones and concrete articles
(net quantity of stacks of cleaned materials will be measured):
15.12 Dismantling doors, windows and clerestory windows (steel or wood)
shutter including chowkhats, architrave, holdfasts etc. complete and
stacking within 50 metres lead :
15.12.1 Of area 3 sq. metres and below each 274.50
15.12.2 Of area beyond 3 sq. metres each 375.65
15.13 Taking out doors, windows and clerestory window shutters (steel or
wood) including stacking within 50 metres lead :
15.13.1 Of area 3 sq. metres and below each 106.55
15.13.2 Of area beyond 3 sq. metres each 140.70
15.14 Dismantling wood work in frames, trusses, purlins and rafters up to
10 metres span and 5 metres height including stacking the material
within 50 metres lead :
15.14.1 Of sectional area 40 square centimetres and above cum 3345.90
15.14.2 Of sectional area below 40 square centimetres metre 13.40
15.15 Extra for dismantling trusses, rafters, purlins etc. of wood work
for every additional span of one metre or part thereof beyond 10
metres :
15.15.1 Of sectional area 40 square centimetres and above cum per
metre span 441.50
15.15.2 Of sectional area below 40 square centimetres metre per
metre span 1.25
15.16 Extra for dismantling trusses, rafters, purlins etc. of wood work
for every additional height of one metre or part thereof beyond 5
metres :
15.16.1 Of sectional area 40 square centimetres and above cum per
metre span 636.25
15.16.2 Of sectional area below 40 square centimetres metre per
metre span 2.50
15.17 Dismantling steel work in single sections including dismembering
and stacking within 50 metres lead in:
15.17.1 R.S. Joists kg 2.45
15.17.2 Channels, angles, tees and flats kg 1.70

No.
15.18 Dismantling steel work in built up sections in angles, tees, flats and
channels including all gusset plates, bolts, nuts, cutting rivets, welding
etc. including dismembering and stacking within 50 metres lead. kg 4.15
15.19 Dismantling steel work manually/ by mechanical means in built up
sections without dismembering and stacking within 50 metres lead
as per direction of Engineer-in-charge. kg 2.75
15.20 Extra for dismantling trusses, rafters, purlins etc. of steel work for kg per
every additional span of one metre or part thereof beyond 10 metres metre span 0.60
15.21 Extra for dismantling trusses, rafters, purlins etc. of steel work for kg per
every additional height of one metre or part thereof beyond 5 metres. metre height 0.60
15.22 Extra for marking of structural steel work required to be re-erected. kg 3.45
15.23 Dismantling tile work in floors and roofs laid in cement mortar including
stacking material within 50 metres lead.
15.23.1 For thickness of tiles 10 mm to 25 mm sqm 54.85
15.23.2 For thickness of tiles above 25 mm and up to 40 mm sqm 85.70
15.24 Demolishing dry brick pitching in floors, drains etc. including stacking
of serviceable material and disposal of unserviceable material within
50 metres lead : cum 940.50
15.25 Dismantling stone slab flooring laid in cement mortar including
within 50 metres lead. sqm 190.30
15.26 Demolishing brick tile covering in terracing including stacking of
serviceable material and disposal of unserviceable material within
50 metres lead. sqm 79.60
15.27 Demolishing mud phaska in terracing and disposal of material within
50 metres lead. cum 652.30
15.28 Dismantling roofing including ridges, hips, valleys and gutters etc.,
and stacking the material within 50 metres lead of:
15.28.1 G.S. Sheet sqm 121.90
15.28.2 Asbestos cement sheet sqm 56.90
15.29 Dismantling stone slab roofing over wooden karries or R.C.C. battens
(dismantling karries and battens to be paid for separately), including
within 50 metres lead. cum 1902.90
15.30 Dismantling jack arch roofing and floors including stacking of
50 metres lead. sqm 181.35
15.31 Dismantling tiled roofing with battens, boarding etc.
complete including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead. sqm 150.00
15.32 Demolishing thatch roofing including mats, bamboo, jaffari etc.
complete including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead. sqm 41.30

No.
15.33 Dismantling wooden ballies in posts and struts including stacking

within 50metres lead. metre 14.95
15.34 Dismantling and stacking within 50 metres lead, fencing posts or
struts including all earth work and dismantling of concrete etc. in
base of:
15.34.1 T’ or ‘L’ iron or pipe each 170.25
15.34.2 R.C.C. each 182.60
15.35 Cutting ballies or wooden posts of fencing at the point of projection
above the concrete or ground and stacking the same within 50 metres
lead. each 11.15
15.36 Dismantling barbed wire or flexible wire rope in fencing including
making rolls and stacking within 50 metres lead. kg 26.25
15.37 Dismantling wooden trellis work excluding frames but including
stacking the serviceable material within 50 metres lead. sqm 47.15
15.38 Dismantling expanded metal or I.R.C. fabrics with necessary battens
and beading including stacking the serviceable material within 50
metres lead. sqm 55.00
15.39 Dismantling wooden boardings in lining of walls and partitions,
excluding supporting members but including stacking within 50
metres lead :
15.39.1 Up to 10 mm thick sqm 44.90
15.39.2 Thickness above 10 mm up to 25 mm sqm 57.30
15.40 Dismantling precast concrete or stone slabs in walls, partition walls
etc. including stacking within 50 metres lead :
15.40.1 Thickness up to 40 mm sqm 208.40
15.41 Dismantling cement asbestos or other hard board ceiling or partition
walls including stacking of serviceable materials and disposal of
unserviceable materials within 50 metres lead. sqm 42.00
15.42 Dismantling C.I. or asbestos rain water pipe with fittings and clamps
including stacking the material within 50 metres lead :
15.42.1 75 to 80 mm dia pipe metre 54.00
15.42.2 100 mm dia pipe metre 55.65
15.42.3 150 mm dia pipe metre 57.30
15.43 Dismantling manually/ by mechanical means including stacking of
50 metres lead as per direction of Engineer-in-charge :
15.43.1 Water bound macadam road sqm 156.00
15.43.2 bituminous road sqm 306.65

No.
15.44 Dismantling G.I. pipes (external work) including excavation and refilling
trenches after taking out the pipes, manually/ by mechanical means
including stacking of pipes within 50 metres lead as per direction of
15.44.1 15 mm to 40 mm nominal bore metre 108.15
15.44.2 Above 40 mm nominal bore metre 117.75
15.45 Dismantling C.I. pipes including excavation and refilling trenches
after taking out the pipes, manually/ by mechanical means breaking
lead caulked joints, melting of lead and making into blocks including
stacking of pipes & lead at site within 50 metre lead as per direction
of Engineer-in-charge:
15.45.1 Up to 150 mm diameter metre 299.05
15.45.2 Above 150 mm dia up to 300 mm dia metre 395.10
15.45.3 Above 300 mm diameter metre 515.45
15.46 Dismantling steel cylinder R.C. pipes including excavation and
refilling trenches after taking out the pipes, manually/ by mechanical
means breaking lead caulked joints, melting of lead and making into
blocks including stacking of pipes & lead at site within 50 metres
lead as per direction of Engineer-in-charge :
15.47 Dismantling asbestos cement pressure pipes including excavation
and refilling trenches after taking out the pipes manually/ by
mechanical means and stacking the pipes within 50 metres lead as
per direction of Engineer-in-charge :
15.48 Taking out C.I. cover with frame from R.C.C. top slab of manholes of
various sizes including demolishing of R.C.C. work manually/ by
mechanical means and stacking of useful materials near the site
and disposal of unserviceable materials within 50 metres lead as per
15.49 Taking out C.I. cover with frame from R.C.C. top slab of inspection
chambers of various sizes including demolishing of R.C.C. work
manually/ by mechanical means and stacking of useful materials
near the site and disposal of unserviceable materials within 50 metres
lead as per direction of Engineer-in-charge. each 292.25
15.50 Dismantling of R.C.C. spun vent shaft including excavating the
cement concrete pit completely, taking out the shaft, refilling
the excavated gap, stacking the useful materials near the site and
disposal of unserviceable materials within 50 metres lead. each 3353.90
15.51 Dismantling of road gully chamber of various sizes including C.I.
grating with frame including stacking of useful materials near the
site and disposal of unserviceable materials within 50 metres lead
including refilling the excavated gap. each 686.70

No.
15.52 Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

including stacking of useful materials near the site and disposal of
unserviceable materials within 50 metres lead. each 668.15
15.53 Dismantling of C.I. sluice valve including stacking of useful materials
within a lead of 50 metres
15.53.1 Up to 150 mm diameter each 239.05
15.53.2 Above 150 mm diameter each 878.70
15.54 Dismantling of spindle fire hydrant including stacking of useful
materials within 50 metres lead. each 537.60
15.55 Dismantling of cement concrete platform along with curtain walls
and base concrete etc. including stacking of useful materials near
the site and disposal of unserviceable materials within 50 metres
lead :
15.55.1 120 x 120 cm (outside to outside) each 787.70
15.56 Dismantling old plaster or skirting raking out joints and cleaning the
surface for plaster including disposal of rubbish to the dumping ground
within 50 metres lead. sqm 39.00
15.57 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed
glazing and false ceiling including disposal of unserviceable material
and stacking of serviceable material with in 50 meters lead
as directed by Engineer-in-charge. sqm 42.00
15.58 Demolishing R.C.C. work by mechanical means and stockpiling at
designated locations and disposal of dismantled materials up to a
lead of 1 kilometre, stacking serviceable and unserviceable material
separately including cutting reinforcement bars. cum 2130.00
15.59 Dismantling of flexible pavement (bituminous courses) by mechanical
means and disposal of dismantled material up to a lead of 1 kilometre,
as per direction of Engineer-in-charge. cum 321.25
15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled
or waste materials by mechanical means, including loading,
transporting, unloading to approved municipal dumping ground or as
approved by Engineer-in-charge, beyond 50 m initial lead, for all leads
including all lifts involved. cum 138.85

SUB HEAD : 16.0
ROAD WORK
264
BASIC RATES (SH: 16.0 ROAD WORK)

No.
0001 Hire charges of Coaltar Boiler 900 to 1400 litres day 800.00
0002 Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper day 800.00
0003 Hire charges of Diesel Road Roller - 8 to 10 tonne day 3000.00
0004 Production cost of concrete by batch mix plant cum 350.00
0007 Hire charges of Coaltar Sprayer day 300.00
0008 Hire charges of Barber green, drying, mixing and Asphalt Plant,
with accessories, capacity 30/45 tonne day 7700.00
0009 Pumping charges of concrete including Hire charges of pump,
piping work & accessories etc. cum 210.00
0012 Vibrator (Needle type 40 mm) day 370.00
0013 Machine for rubbing of floors day 300.00
0014 Front end loader capacity 1.00 cum day 6000.00
0016 Mastic Cooker day 750.00
0017 Hire and running charges of tipper day 1700.00
0018 Hire and running charges of loader day 5000.00
0021 Pin vibrator day 325.00
0022 Surface Vibrator day 400.00
0023 Hot Bitumen Mixer 0.5 cum i/c hand cart day 3500.00
0029 Carriage of concrete by transit mixer km/cum 30.00
0030 Generator 250 KVA day 2500.00
0033 Paint applicator day 750.00
0042 C.C .batch mix plant day 10000.00
0043 Road sweeper day 550.00
0045 Slip form paver with sensor day 13000.00
0046 Water tanker 5000 litre day 1200.00
0047 Concrete joint cutting machine day 900.00
0048 Texturing machine day 925.00
0049 Dozer D-80-A 12 hour 1500.00
0050 Motor Grader 3.35 metre blade hour 2450.00
0051 Hydraulic Excavator of 1 cum bucket hour 1000.00
0052 Front end loader 1 cum bucket capacity hour 900.00
0053 Tipper-5 Cum tonne/km 3.00
0054 Vibratory roller 8 to 10 tonne hour 600.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 300.00
0056 Tandem Road Roller hour 1200.00
SUB HEAD : 16.0 ROAD WORK 265

No.
0057 Water Tanker 5 to 6 KL capacity hour 150.00

0059 Wet Mix Plant 60 TPH hour 800.00
0060 Mechanical Broom Hydraulic hour 360.00
0061 Emulsion Pressure Distributor of capacity 1750 sqm per hour hour 800.00
0062 Hot mix Plant -120 TPH capacity hour 15000.00
0063 Hot mix Plant 100 TPH Capacity hour 13000.00
0064 Paver finisher Hydrostatic with sensor control 100 TPH hour 1500.00
0065 Paver finisher Mechanical 100 TPH hour 800.00
0066 Batching and Mixing Plant @ 75 cum per hour hour 2400.00
0068 Concrete Paver finisher with 40 HP Motor and sensor hour 3000.00
0069 Generator 250 KVA hour 350.00
0070 Generator 100 KVA/125 KVA hour 250.00
0071 Truck 5.5 cum/10 tonnes tonne km 3.00
0075 Road sweeper (Mechamical Broom) @ 1250 sqm per hour hour 350.00
0076 Drum Type HMP of 60-90 TPH capacity @ 75 tonne per hour
actual output hour 12000.00
0083 Hire charges of TATA 407 or equivalent for local shifting. day 1200.00
0113 Chowkidar day 558.00
0125 Mason (for plain stone work) 2nd class day 679.00
0128 Mate day 617.00
0157 Operator (Pile/ Special machine) day 738.00
0286 Brick Aggregate (Single size) : 50 mm nominal size cum 650.00

No.

0296 Stone Aggregate (Single size) : 12.5 mm nominal size cum 1350.00
0304 Bajri cum 1000.00
0309 Paving bitumen of grade VG-10 of approved quality tonne 25614.00
0310 Bitumen emulsion tonne 30099.00
0312 Bitumen grade PMB - 40 tonne 32200.00
0313 Blown type petroleum bitumen of penetration 85/25 of approved
quality tonne 34000.00
0314 Bitumen hot sealing compound : grade A kg 28.00
0317 Premoulded joint filler 12 mm thick sqm 360.00
0323 Separation Membrane of impermeable plastic sheeting
125 micron thick sqm 12.00
0349 Curing compound litre 38.00
0364 Wire brush each 20.00
0365 Soft brush each 20.00
0369 Plastic sheet,1.25 mm thick for dowel bars sqm 25.00
0370 Coal (steam) quintal 440.00
0371 Sealant primer kg 130.00
0374 Pre moulded Joint filler, 25 mm thick for expansion joint. sqm 400.00
0773 Unslaked lime quintal 300.00
0784 Marble dust/ powder cum 1130.00
0810 Moorum cum 500.00
0979 Royalty for good earth cum 40.00
0983 Fine sand (zone IV) cum 900.00
1005 Twisted steel/ deformed TMT bars Fe-500D quintal 4600.00

No.
1013 Mild steel sheets of 1.00 mm thickness for tanks quintal 4600.00
1021 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not
less than 7.75 kg/sqm sqm 430.00
1028 Straining bolts each 80.00
1029 Galvanised steel barbed wire of 9.8 kg /100metre quintal 5500.00
1030 Galvanised steel turn buckles each 25.00
1151 Boundary stone top chisel dressed 15x15x90 cm each 80.00
1158 Stone for pitching 15 cm x 22.5 cm cum 600.00
1159 Stone dust cum 1100.00
1235 Diesel litre 73.50
1241 Commercial LPG in cylinder kg 82.00
1980 Fly ash cum 10.00
2200 Carriage of Steam coal tonne 120.00
2206 Carriage of Stone aggregate 40 mm nominal size and above cum 112.79
2208 Carriage of Lime cum 103.77
2211 Carriage of Tar / Bitumen tonne 103.77
2215 Carriage of Soling stone & masonry stone cum 122.08
2241 Carriage of Good earth cum 129.71
2260 Carriage of Brick aggregate cum 112.79
2261 Carriage of Fine sand cum 103.77
2265 Carriage of Moorum cum 103.77
2266 Carriage of Surkhi cum 103.77
2267 Carriage of Stone dust cum 103.77
2302 Carriage of G.I. sheet and accessories tonne 92.24
2311 Carriage of Red bajri cum 103.77
2314 Carriage of Barbed wire tonne 92.24
2335 Carriage of sand cum 103.77
2342 Carriage of Solvent / Diesel. quintal 10.38
2704 Aluminium Strip 40 mm wide and 2 mm thick kg 240.00
2901 Stone Aggregate (Single size): 100 mm nominal size cum 1350.00

No.

2903 Stone chippings/ screenings 4.75 mm nominal size cum 1400.00
2904 Stone chippings/ screenings 150 micron nominal size cum 1400.00
2908 Over burnt (Jhama) Brick Aggregate: 120 mm to 40 mm size cum 500.00
2910 Stone chippings/ screenings 12.5/ 13.2 mm nominal size cum 1150.00
2914 Solvent kg 25.00
2916 Paving Asphalt VG 10 of approved quality tonne 24000.00
5001 Mobil oil litre 315.00
6501 Sand zone V (Jamuna) cum 1225.00
7254 Hardening compound litre 38.00
7255 Road marking paint (spirit based) litre 115.00
7256 Superior quality road marking paint (water based) litre 135.00
7280 Waste plastic additive tonne 40000.00
7295 Granite of any colour, 18 mm thick (slab area upto 0.50 sqm) sqm 1600.00
7309 Paving Asphalt of grade VG-30 of approved quality tonne 39570.00
7318 Plasticizer / super plasticizer kg 36.00
7382 Bitumen emulsion rapid setting (R.S.) confirming to IS : 8887 tonne 19000.00
7426 Cat's eye each 100.00
7739 Modified Bitumen Refinery produced CRMB - 55 tonne 29995.00
7742 Bitumen emulsion medium setting (M.S.) conforming to IS : 8887 tonne 27909.00
7753 Stone Boulder 50 mm to 200 mm cum 850.00
7773 Coloured inter locking C.C. paver Block (60 mm thick, M-35) sqm 450.00
7774 Stone size 10x10x7.50cm each 10.00
7893 Tactile tile sqm 1000.00
7895 Matt finished vitrified tile 100x100 x16 mm sqm 1000.00
7896 Vitrified tile sqm 500.00
8576 Powder coated Galvanized Iron intermediate cross-T section wire
diameter 3.00 mm). sqm 190.00
8577 Crates made of Mesh type 10x12 (D=100 mm) Zn+PVC coated.
Mesh wire diameter 2.70/3.70 mm (ID/OD). sqm 220.00
8578 Crates made of Mesh type 10x12 (D=100 mm) Zn+10% Al alloy +
PVC coated. Mesh wire diameter 2.70/3.70 mm (ID/OD). sqm 290.00
8685 Delineator each 300.00
8686 Precast C.C. Kerb stone M - 25 cum 5500.00
8687 Thermoplastic paint kg 65.00

No.
8688 Glass beads kg 70.00

8689 Interlocking C.C. paver block ( 60 mm thick, M-30) sqm 400.00
8690 High intensity retro - reflective sheet as per IRC 67-2001 sqm 1300.00
8691 Punched tape concertina coil 600 mm dia 10 m openable
length (Total length 90 m) bundle 600.00
8692 RBT reinforced barbed wire metre 6.50
8693 Turn buckle and strengthening bolt each set 40.00
8694 Precast pavement slab 450 x 450 x 50 mm (M - 30) each 135.00
8695 Chain link fabric fencing mesh of size 50x50 mm made of
G.I. wire of dia 4 mm sqm 280.00
G.I. wire of dia 4 mm, PVC coated to outer dia 5 mm sqm 300.00
G.I. wire of dia 3 mm sqm 360.00

16.0 ROAD WORK
No.
ROADS
16.1 Preparation and consolidation of sub grade with power road roller of
8 to 12 tonne capacity after excavating earth to an average of 22.5
cm depth, dressing to camber and consolidating with road roller
including making good the undulations etc. and re-rolling the sub
grade and disposal of surplus earthwith lead upto 50 metres. sqm 156.75
16.2 Extra for compaction of earth work in embankment under optimum
moisture conditions to give at least 95% of the maximum dry density
(proctor density). cum 18.20
16.3 Supplying and stacking at site.
16.3.1 90 mm to 45 mm size stone aggregate cum 1840.05
16.3.2 63 mm to 45 mm size stone aggregate cum 1535.65
16.3.3 53 mm to 22.4 mm size stone aggregate cum 1749.75
16.3.4 Over burnt (Jhama) brick aggregate 120 mm to 40 mm cum 819.85
16.3.6 Stone screening 13.2 mm nominal size (Type A) cum 1727.65
16.3.7 Stone screening 11.2 mm nominal size (Type B) cum 1978.50
16.3.8 Red bajri cum 1476.80
16.3.9 Good earth cum 483.90
16.3.10 Moorum cum 807.80
16.4 Laying, spreading and compacting stone aggregate of specified sizes
to WBM specifications in uniform thickness, hand picking, rolling
with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to
proper grade and camber, applying and brooming requisite type of
screening / binding material to fill up interstices of coarse aggregate,
watering and compacting to the required density . cum 767.25
16.5 Laying water bound macadam sub-base with brick aggregate and
binding material, earth etc. including screening, sorting and spreading
to template and consolidation with light power road-roller etc.
complete.(payment for brick aggregate and moorum etc. to be made
separately)
16.6 Supplying, stacking and Spreading 6 mm thick red bajri, watering
and rolling complete including preparation of the surface and rolling.
16.6.1 With road roller/ hand roller sqm 19.90
16.7 Brick edging in full brick width and half brick depth including
excavation, refilling and disposal of surplus earth lead upto 50 metres.
16.7.1 With common burnt clay F.P.S. (non modular) bricks of
class designation 7.5 metre 167.80

No.
16.8 Brick edging laid lengthwise with half brick depth including excavation,
refilling and disposal of surplus earth lead upto 50 metres :
16.9 Scarifying metalled (water-bound) road surface including disposal of
rubbish, lead upto 50 m and consolidation of the aggregate received
from scarifying with power road roller of 8 to 10 tonne capacity. sqm 24.55
16.10 Making bajri path including preparation of subgrade, supplying and
laying brick aggregate of 50 mm nominal size 7.5 cm deep with
blinding material consisting of 12 mm moorum and 12 mm red bajri
consolidated with road roller. sqm 172.45
16.11 Dry stone pitching 22.5 cm thick including supply of stones and
preparing surface complete. sqm 730.20
16.12 Dry brick pitching half brick thick in drains including supply of bricks
and preparing the surface complete :
class designation 7.5 sqm 568.70
16.13 Cutting road and making good the same including supply of extra
quantities of materials i.e. aggregate, moorum screening, red bajri
and labour required.
16.13.1 bituminous portion cum 3677.15
16.13.2 Water bound macadam cum 2275.95
16.14 Cutting bajri paths and making good the same including supply of
extra quantities of brick aggregate, moorum and red bajri required. sqm 212.25
FENCING
16.15 Supplying at site :
16.15.1 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3
(1 cement : 1.5 coarsesand : 3 graded stone aggregate
12.5 mm nominal size) with wooden plugs or 6mm bar
nibs wherever required as per direction of Engineer-in-
charge (cost of earth works in excavation, concrete works
in foundation to be paid separately). cum 26754.35
16.15.2 Welded steel wire fabric of required width having
rectangular mesh painted with two or more coats of enamel
paint of approved shade over a coat of primer (Priming &
Painting to be paid for separately). kg 74.35
16.16 Supplying and fixing turn buckles and straining bolts for barbed wire
fencing. each set 238.65
16.17 Fencing with R.C.C. post placed at required distance, embedded in
cement concrete blocks, every 15th post, last but one end post and
corner post shall be strutted on both sides and end post one side
only, provided with horizontal lines and two diagonals of barbed wire
weighing 9.38 kg per 100 metres (minimum), between the two posts
fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire
tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C.

No.
posts, struts, earth work and concrete to be paid for separately) :-

Payment to be made per metre cost of total length of barbed wire
used.
16.17.1 With G.I. barbed wire metre 12.00
16.18 Fencing with angle iron post placed at required distance embedded
in cement concrete blocks, every 15th post, last but one end post
and corner post shall be strutted on both sides and end post on one
side only and provided with horizontal lines and two diagonals
interwoven with horizontal wires, of barbed wire weighing 9.38 kg per
100 m (minimum), between the two posts fitted and fixed with G.I.
staples, turn buckles etc. complete. (Cost of posts, struts, earth
work and concrete work to be paid for separately). Payment to be
made per metre cost of total length of barbed wire used.
16.18.1 With G.I. barbed wire metre 19.05
16.19 Supplying at site Angle iron post & strut of required size including
bottom to be split and bent at right angle in opposite direction for
10 cm length and drilling holes upto 10 mm dia. etc. complete. kg 92.40
16.20 Welded steel wire fabric fencing with posts of specified material and
of standard design placed and embedded in cement concrete blocks
45x45x 60 cm of mix 1:5:10 (1 cement:5 fine sand : 10 graded stone
aggregate 40 mm nominal size), every 15th post, last but one end
post and corner post shall be strutted on both sides and end post on
one side only and struts embedded in cement concrete blocks
70x45x50 cm of the same mix, provided with welded steel wire fabric
fixed between the posts fitted and fixed with G.I. staples on wooden
plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts,
welded steel wire fabric, painting, earth work in excavation and
concrete to be paid for separately).
sqm 51.00
ROAD SIGNS
16.21 Engraving letters in hard stone per cm
height
per letter 8.20
16.22 Providing and fixing 15x15x90 cm boundary stone of hard stone with
top 30 cm chisel dressed on all four sides including top (cost of
excavation, refilling and concrete etc. to be paid for separately).
each 207.75
16.23 Providing and fixing 15 cm dia at top, 20 cm at bottom and 90 cm
high precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5
coarse sand : 3 graded stone aggregate 20 mm nominal size)
boundary stone as per standard design, including finishing smooth
with cement mortar 1:3 (1 cement : 3 fine sand) (cost of excavation,
refilling and concreting to be paid for separately). each 663.55
16.24 Providing and fixing precast reinforced cement concrete 1:1.5:3 (1
cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal
size) kilometre stone as per standard design, including finishing
smooth in 1:3 cement mortar (1 cement : 3 fine sand) but excluding

No.
the cost of earth work, concrete in foundation, painting and lettering

etc. which shall be paid for separately.
16.24.1 35x111x25 cm size each 2308.50
16.24.2 50x152.5x25 cm size each 4211.25
16.24.3 35x93.5x18 cm size each 1546.00
SURFACE DRESSING
16.25 Surface dressing on new surface with paving bitumen of grade VG -
10 of approved quality using 2.25 kg of bitumen per sqm with 1.65
cum of stone chippings 13.2 mm nominal size per 100 sqm of road
surface, including consolidation with road roller of 6 to 8 tonne
capacity etc. complete: sqm 167.25
16.26 Surface dressing on new surface in two coats with bitumen of grade
VG -10 of approved quality using 1.8 kg of bitumen per sqm with 1.5
cum of stone chippings 13.2 mm nominal size per 100 sqm of road
surface for first coat and 1.1 kg. of bitumen per sqm with 1.00 cu.
metre of stone chippings 11.2 mm nominal size per 100 sqm of road
surface for second coat, including consolidation of each coat
separately with road roller of 6 to 8 tonne capacity etc. complete. sqm 232.05
16.27 Surface dressing on old surface with hot bitumen of grade VG - 10 of
approved quality using 1.95 kg of bitumen per sqm with 1.50 cum of
stone chippings 11.2 mm nominal size per 100 sqm of road surface,
including consolidation with road roller of 6 to 8 tonne capacity, etc.
complete. sqm 130.40
16.28 Surface dressing one coat on new surface with bitumen of specified
grade at a rate of 1.95 kg/sqm of surface area with 1.5 cum of stone
chippings 13.2 mm nominal size per 100 sqm of road surface,
including consolidation with road roller of 6 to 8 tonne capacity , etc.
complete :
16.28.1 Using bitumen emulsion (minimum 50% bitumen content-
RS grade conforming to IS : 8887) sqm 157.95
16.29 Surface dressing one coat on old surface with bitumen of specified
grade at the rate of 1.22 kg/ sqm of surface area with 1.10 cum of
stone chippings 11.2 mm nominal size per 100 sqm of road surface,
including consolidation with road roller of 6 to 8 tonne capacity etc.
complete :
16.29.1 Using bitumen emulsion (minimum 50% bitumen content-
RS grade conforming to IS : 8887) sqm 100.00
PREMIX CARPET
16.30 Providing and applying tack coat using hot straight run bitumen of
grade VG - 10, including heating the bitumen, spraying the bitumen
with mechanically operated spray unit fitted on bitumen boiler,
cleaning and preparing the existing road surface as per
specifications :
16.30.1 On W.B.M. @ 0.75 Kg / sqm sqm 42.05
16.30.2 On bituminous surface @ 0.50 Kg / sqm sqm 33.65

No.
16.31 Providing and applying tack coat using bitumen emulsion conforming
to IS:8887, using emulsion pressure distributer including preparing
the surface & cleaning with mechanical broom.
16.31.1 With rapid setting bitumen emulsion
16.31.1.1 On W.B.M / W.M.M. @ 0.4kg/sqm sqm 11.85
16.31.1.2 On bituminous surface @ 0.25kg/sqm sqm 8.05
16.31.2 With medium setting bitumen emulsion
16.31.2.1 On W.B.M / W.M.M. @ 0.4kg/sqm sqm 16.65
Note - Use of Item No. 16.81.1 shall be restricted only per site
at sub zero temperature or for emergency application
16.32 2 cm premix carpet surfacing with 1.8 cum and 0.90 cum of stone
chippings of 13.2 mm size and 11.2 mm size respectively per 100
sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings
of 13.2 mm and 11.2 mm size respectively, including a tack coat
with hot straight run bitumen, including consolidation with road roller
of 6 to 9 tonne capacity etc. complete (tack coat to be paid for
separately).
16.32.1 With paving Asphalt grade VG - 10 heated and then mixed
with solvent at the rate of 70 grams per kg of asphalt sqm 173.05
16.32.2 With paving Asphalt grade VG - 30 with no solvent sqm 199.65
16.32.3 With Refinery Modified Bitumen CRMB 55 conforming to
IRC: SP: 53 sqm 184.60
16.33 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone
chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm
and 52 kg and 56 kg of hot bitumen per cum of stone chippings of
13.2 mm and 11.2 mm size respectively, including a tack coat with
hot straight run bitumen, including consolidation with road roller of 6
to 9 tonne capacity etc. complete (tack coat to be paid for separately).
16.33.2 With paving Asphalt grade VG - 30 with no solvent sqm 241.00
IRC: SP: 53 sqm 222.20
16.34 2 cm premix carpet surfacing with 2.4 cum of stone chippings 11.2
mm nominal size per 100 sqm and bitumen emulsion (medium setting
min. 65% bitumen content) complying with IS : 8887, using 96 kg
per cum of chippings, including consolidation with road roller of 6 to
9 tonne capacity etc. complete. sqm 164.25
16.35 2.5 cm premix carpet surfacing with 3 cum of stone chippings 10
mm nominal size per 100 sqm and bitumen emulsion (medium setting
min. 65% bitumen contents) complying with IS : 8887, using 96 kg
per cum of chippings of road surface, including consolidation with
road roller etc complete . sqm 198.35

No.
16.36 Providing and laying Bitumen Penetration Macadam with hard stone
aggregate of quality, size and grading as specified, with bitumen of
suitable penetration grade, including required key aggregate as
specified, spreading coarse aggregate with the help of self propelled/
tipper tail mounted aggregate spreader and applying bitumen by a
pressure distributor and then spreading key aggregate with the help
of aggregate spreader complete, including consolidation with road
roller of minimum 8 to 10 tonne capacity to achieve specified values
of compaction and surface accuracy :
16.36.1 For 50mm compacted thickness using coarse aggregate
of size 50-20 mm graded @ 0.60 cum per 10 sqm key
aggregate of size 12.5 mm graded @ 0.15 cum per 10
sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm. sqm 390.15
16.36.2 For 75 mm compacted thickness in two layers using stone
aggregate of size 63-41 mm graded @ 0.90 cum per 10
sqm key aggregate of size 20.0 mm graded @ 0.18 cum
per 10 sqm. With paving asphalt grade VG - 10 @ 68 kg/
10 sqm. sqm 572.35
16.37 Providing and laying bitumen mastic wearing course (as per
specifications) with industrial bitumen of grade 85/25 conforming to
IS : 702, prepared by using mastic cooker and laid to required level
and slope, including providing antiskid surface with bitumen precoated
fine grained hard stone chipping of approved size at the rate of 0.005
cum per 10 sqm and at approximate spacing of 10 cm centre to
centre in both directions, pressed into surface protruding 1 mm to 4
mm over mastic surface, including cleaning the surface, removal of
debris etc. all complete. (Considering bitumen using 10.2% as per
MORTH specification).
16.37.1 25 mm thick sqm 671.85
16.37.2 40 mm thick sqm 1074.95
16.38 2.5 cm thick bitumastic sheet with hot bitumen of approved quality,
using stone chippings (60% with 12.5 mm nominal size and 40%
with 10 mm nominal size) @ 1.65 cum per 100 sqm and coarse
sand @ 1.65 cum per 100 sqm of road surface and with bitumen @
56 kg/cum of stone chippings and @ 128 kg/cum of sand over a
tack coat with hot straight run bitumen, including consolidation
with road roller of 8 to 10 tonne etc. complete. (tack coat to be paid
separately) :
16.38.2 With paving Asphalt grade VG - 30 sqm 317.45
IRC: SP : 53 sqm 285.75
16.39 4 cm thick bitumastic sheet with hot bitumen of approved quality,
using stone chippings (60% with 12.5 mm nominal size and 40%
with 10 mm nominal size) @ 2.60 cum per 100 sqm and coarse
sand @ 2.60 cum per 100 sqm of road surface and with bitumen @

No.
56 kg/cum of stone chippings and @ 128 kg/cum of sand over a

tack coat with hot straight run bitumen, including consolidation
with road roller of 8 to 10 tonne etc. complete. (tack coat to be paid
separately) :
16.39.2 With paving asphalt grade VG - 30 with no solvent sqm 481.55
IRC: SP : 53 sqm 431.45
SEAL COAT
16.40 Providing and laying seal coat of premixed fine aggregate ( passing
2.36 mm and retained on 180 micron sieve) with bitumen using 128
kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate
and 0.60 cum of fine aggregate per 100 sqm of road surface, including
rolling and finishing with road roller all complete. sqm 73.70
16.41 Providing and laying seal coat over prepared surface of road with
bitumen heated in bitumen boiler fitted with the spray set spraying
using 98 kg of bitumen of grade VG - 10 and blinding surface with
0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm
sieve and retained on 2.36 mm sieve) per 100 sqm of road surface,
including rolling and finishing with power road roller all complete. sqm 99.15
Note: Seal coat items to be operated only with the prior approval of
chief Engineer concerned.
CONCRETE PAVEMENTS
16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 40 mm nominal size) in pavements, laid to required slope
and camber in panels as required including consolidation finishing
and tamping complete. cum 6840.85
16.43 Providing and laying design mix cement concrete of M-30 grade, in
roads/ taxi tracks/ runways, using cement content as per design
mix, using coarse sand and graded stone aggregate of 40 mm nominal
size in appropriate proportions as per approved & specified design
criteria, providing dowel bars with sleeve/ tie bars wherever required,
laying at site, spreading and compacting mechanically by using
needle and surface vibrators, levelling to required slope/ camber,
finishing with required texture, including steel form work with sturdy
M.S. channel sections, curing, making provision for contraction/
expansion, construction & longitudinal joints (10 mm wide x 50 mm
deep) by groove cutting machine, providing and filling joints with
approved joint filler and sealants, complete all as per direction of
Engineer-in-charge (Item of joint fillers, sealants, dowel bars with
sleeve/ tie bars to be paid separately).
Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/
less cement used as per design mix is payable/ recoverable separately.
16.43.1 Cement concrete prepared with batch mixing machine cum 8752.35
16.43.2 Cement concrete manufactured in automatic batching
plant (RMC plant) i/c transportation to site in transit mixer cum 9153.75

No.
16.44 Extra for providing and mixing hardening compound of approved quality
as per manufacturer’s specification in cement concrete. litre 50.85
16.45 Providing and fixing in position pre-moulded joint filler in expansion per cm depth
joints. per cm width
per metre
length 3.10
16.46 Providing and laying in position bitumen hot sealing compound for
expansion joints etc.
16.46.1 Using grade ‘A’ sealing compound. per cm depth
per cm width
per metre
length 3.30
PAINTING AREA/RUNWAY MARKING
16.47 Painting runway/taxi track/apron marking with adequate nos of coats
to give uniform finish with road marking paint of superior make as
approved by the Engineer-in-charge, i/c cleaning the surface of ail
dirt, scales, oil, grease and other foreign material etc. and lining out
complete.
16.47.1 New work (Two or more coats) sqm 150.85
16.47.2 Old work (One or more coats) sqm 96.40
16.48 Painting road surface marking with adequate nos of coats to give
uniform finish with ready mixed road marking paint conforming to IS
: 164, on bituminous surface in white/yellow shade, including cleaning
the surface of all dirt, scales, oil, grease and foreign material etc.
complete.
16.48.1 New work (Two or more coats) sqm 215.95
16.48.2 Old work (One or more coats) sqm 141.70
MISCELLANEOUS
16.49 Making bell mouth opening/ entrance of size 100x50x50 cm for
drainage pipe under footpath, including providing cement concrete
1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size) for shape of bell mouth, including plastering providing
and fixing precast R.C.C./ S.F.R.C. slab including plastering with
cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on
exposed surface of the slab & bell mouth including centring, shuttering
& neat cement punning inside the bell mouth etc. all complete. each 2481.60
16.50 Providing and fixing Glow studs of size 100x20 mm made of heavy
duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or
HIP (High impact polystyrene) or ABS having electronically welded
micro- prismatic lens with abrasion resistant coating as approved by
Engineer in charge. The glow stud shall support a load of 13635 kg
tested in accordance with ASTM D4280. The slope of retro- reflective
surface shall be 35 (+/-5) degress to base .The reflective panels on
both sides with at least 12 cm of reflective area up each side. The
luminance intensity should be as per the specification and shall be
tested as described in ASTM I: 809 as recommended in BS: 873

No.
part 4 : 1973. The studs shall be fixed to the Road surface using the
adhesive conforming to IS, as per procedure recommended by the
manufacturer complete and as per direction of Engineer-in-charge. each 196.40
16.51 Preparation of sub-base road pavement with commercial dry lime
(slaked), fly ash stabilised soil with a mix of 3% lime, 12% fly ash and
85% local suitable soil by weight, so as to achieve minimum field C.B.R.
of 20, including mixing, rolling with road roller curing etc. all complete.
16.51.1 Minimum thickness 15 cm cum 1111.05
16.52 Providing and fixing precast lime fly ash concrete blocks 1:2:3:6 (1
lime: 2 fly ash : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size), including finishing with 10mm thick cement mortar
1:3 (1 cement : 3 coarse sand) in foot paths, including preparation of
sub grade with a hand rammer, laying 10 mm thick leveling course of
fine sand (jamuna sand) and filling the joints with fine sand. cum 10802.45
16.53 Providing and fixing concertina coil fencing with punched tape
concertina coil 600 mm dia 10 metre openable length ( total length
90 m), having 50 nos rounds per 6 metre length, upto 3 m height of
wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart
and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with
G.I. staples and G.I. clips to retain horizontal, including necessary
bolts or G.I. barbed wire tied to angle iron, all complete as per direction
of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring
core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm
with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of
M.S. angle, C.C. blocks shall be paid separately) metre 290.80
16.54 Providing and laying Dense Graded Bituminous Macadam using
crushed stone aggregates of specified grading, premixed with
bituminous binder and filler, transporting the hot mix to work site by
tippers, laying with paver finisher equiped with electronic sensor to
the required grade, level and alignment and rolling with smooth
wheeled, vibratory and tandem rollers as per specifications to achieve
the desired compaction and density, complete as per specificatons
and directions of Engineer-in-Charge.
16.54.1 50 to 100 mm average compacted thickness with bitumen
of grade VG-30 @ 5% (percentage by weight of total mix) and lime
filler @ 2% (percentage by weight of Aggregate) prepared in Batch
Type Hot Mix Plant of 100-120 TPH capacity. cum 10064.25
of grade VG-30 @ 5% (percentage by weight of total mix) and lime
filler @ 2% (percentage by weight of Aggregate) prepared in Drum
16.55 Providing and laying bituminous macadam using crushed stone
aggregates of specified grading premixed with bituminous binder,
transported to site by tippers, laid over a previously prepared surface
with paver finisher equiped with electronic sensor to the required
grade, level and alignment and rolling with smooth wheeled, vibratory
and tandem rollers as per specifications to achieve the desired
compaction and density, complete as per specificatons and directions
of Engineer-in-Charge.

No.

of grade VG-30 @ 3.50% (percentage by weight of total
mix) prepared in Batch Type Hot Mix Plant of 100-120
TPH capacity. cum 7743.55
of grade VG-30 @ 3.50% (percentage by weight of total
mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH
capacity. cum 7665.25
16.56 Providing and laying semi- dense Bituminous concrete using crushed
stone aggregates of specified grading, premixed with bituminous
binder and filler, transporting the hot mix to work site by tippers,
laying with paver finisher equiped with electronic sensor to the required
grade, level and alignment and rolling with smooth wheeled, vibratory
and tandem rollers to achieve the desired compaction and density
as per specification, complete and as per directions of Engineer-in-
Charge.
16.56.1 25 mm compacted thickness with bitumen of grade VG-
30 @ 5% (percentage by weight of total mix) and lime
filler @ 2% (percentage by weight of Aggregate) prepared
in Batch Type Hot Mix Plant of 100-120 TPH capacity. sqm 250.75
16.56.2 25 mm compacted thickness with bitumen of grade VG-
30 @ 5% (percentage by weight of total mix) and lime
filler @ 2% (percentage by weight of Aggregate) prepared
in Drum Type Hot Mix Plant of 60-90 TPH capacity. sqm 248.70
16.57 Providing and laying Bituminous concrete using crushed stone
aggregates of specified grading, premixed with bituminous binder
and filler, transporting the hot mix to work site by tippers, laying with
paver finisher equiped with electronic sensor to the required grade,
level and alignment and rolling with smooth wheeled, vibratory and
tandem rollers to achieve the desired compaction and density as per
specification, complete and as per directions of Engineer-in-Charge.
16.57.1 40/50 mm compacted thickness with bitumen of grade
VG-30 @ 5.5% (percentage by weight of total mix) and
lime filler @ 3% (percentage by weight of Aggregate)
prepared in Batch Type Hot Mix Plant of 100-120 TPH
lime filler @ 3% (percentage by weight of Aggregate) and
waste plastic additive @ 8% (percentage by weight of
bitumen) prepared in Batch Type Hot Mix Plant of 100-
120 TPH capacity. cum 11499.40
PMB-40 @ 5.5% (percentage by weight of total mix) and

No.

CRMB-60 @ 5.5% (percentage by weight of total mix)
and lime filler @ 3% (percentage by weight of Aggregate)
prepared in drum Type Hot Mix Plant of 60-90 TPH
lime filler @ 3% (percentage by weight of Aggregate) and
waste plastic additive @ 8% (percentage by weight of
bitumen) prepared in drum Type Hot Mix Plant of 60-90
PMB-40 @ 5.5% (percentage by weight of total mix)
CRMB-60 @ 5.5% (percentage by weight of total mix)
prepared in Drum Type Hot Mix Plant of 60-90 TPH
16.59 Manufacturing, supplying and fixing retro reflective sign boards made
up of 2 mm thick aluminium sheet, face to be fully covered with high
intensity encapsulated type heat activated retro reflective sheeting
conforming to type - IV of ASTM-D 4956-01 in blue and silver white or
other colour combination including subject matter, message (bi-lingual),
symbols and borders etc. as per IRC ; 67:2001, pasted on substrate
by an adhesive backing which shall be activated by applying heat and
pressure conforming to class -2 of ASTM-D-4956-01 and fixing the
same with suitable sized aluminium alloy rivets @ 20 cm c/c to back
support frame of M.S. angle iron of size 25x25x3 mm along with theft
resistant measures, mounted and fixed with 2 Nos. M.S. angles of
size 35x35x5 mm to a vertical post made up to M.S. Tee section
ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at
the bottom end and including making holes in pipes, angles flats,
providing & fixing M.S. message plate of required size, steel work to
be painted with two or more coats of synthetic enamel paint of required
shade and of approved brand & manufacture over priming coat of zinc

No.
chromate yellow primer (vertical MS-Tee support to be painted in black

and white colours).Backside of aluminium sheet to be painted with
two or more coats of epoxy paint over and including appropriate priming
coat including all leads and lifts etc. complete as per drawing,
specification and direction of Engineer-in-charge.
16.59.1 Mandatory/ Regulatory sign boards of 900 mm diametre
with support length of 3750 mm each 5996.95
16.59.2 Cautionary /warning sign boards of equilateral triangular
shape having each side of 900 mm with support length of
3650 mm each 4533.85
16.60 Manufacturing, supplying and fixing retro reflective overhead signage
boards made up of 2 mm thick aluminium sheet, face to be fully
covered with high intensity and encapsulated lens type heat activated
retro reflective sheeting conforming to type - III of ASTM-D-4956-01
as approved by Engineer-in-charge, letters, borders etc. as per IRC
: 67-2001 in silver white with blue colour back ground and with high
intensity grade, pasted on substrate by pressure sensitive adhesive
backing which shall be activated by applying pressure conforming to
class II of ASTM-D-4956-01 and fixing the same to the plate of
structural frame work by means of suitable sized aluminium alloys,
rivets or bolts & nuts @ 300 mm centre to centre all along the
periphery as well as in two vertical rows along with theft resistant
measures, including the cost of painting with two or more coats of
epoxy paint in grey colour on the back side of aluminium sheet
including appropriate priming coat. The rate includes the cost of
rounding off the corners, lowering down the structural frame work
from the gantry, fixing and erecting the same in position all complete
as per drawings, specification and direction of the engineer-in-
charge.(Structural frame work including M.S. plate to be provided
separately. Rectangular area of the sheet only shall be measured for
payment).
16.60.1 Overhead informatory road signage sqm 5284.45
16.61 Providing Retro-reflective regulatory sign board of size 900 mm dia
meter made out of 2 mm thick aluminium sheet, face to be fully
covered with high intensity encapsulated lens type retro -reflective
sheeting as approved by Engineer-in-charge . Letter, symbols, borders
etc. will be as per IRC - 67 with required colour scheme on the
boards and with the high intensity grade A. The aluminium sheet to
be riveted to M.S. frame of angle iron of size 40x40x4 mm. The
boards will be fixed to 1 No. 50x50 mm square post made of M.S.
angle 50x50x4 mm, 4 m long welded to the frame with adequate
anti-theft arrangement .Sheet work to be painted with two or more
coats of synthetic enamel paint over an under coat (primer) and
back side of aluminium sheet to be painted with two or more coats of
epoxy paint including appropriate priming coat complete in all respects
as per direction of Engineer-in-charge. each 6729.90
16.62 Providing and applying 2.5 mm thick road marking strips (retro-
reflective) of specified shade/ colour using hot thermoplastic material
by fully/ semi automatic thermoplastic paint applicator machine fitted

No.
with profile shoe, glass beads dispenser, propane tank heater and
profile shoe heater, driven by experienced operator on road surface
including cost of material, labour, T&P, cleaning the road surface of
all dirt, seals, oil, grease and foreign material etc. complete as
per direction of Engineer-in-charge and accordance with applicable
specifications. sqm 607.30
16.63 Providing, laying and making kerb channel 30 cm wide and 50 mm
thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded
stone aggregate 20 mm nominal size) over 75mm bed of dry brick
ballast 40 mm nominal size, well rammed and consolidated
and grouted with fine sand, including finishing the top smooth etc.
complete and as per direction of Engineer-in-charge. sqm 483.00
16.64 Providing and laying 75 mm thick compacted bed of dry brick
aggregate of 40 mm thick nominal size including spreading, well
ramming, consolidating and grouting with jamuna sand, including
finishing smooth etc. complete as per direction of Engineer-in-charge. sqm 176.70
16.65 Providing and fixing post delineators made of ABS round body fitted
with 2 nos 100 mm dia high reflective reflectors and mounted on MS
pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to
be installed as per direction of Engineer-in-charge. each 714.45
16.66 Excavating holes upto 0.10 cum, including getting out the excavated
soil, then returning the soil as deported in layers not exceeding 20
cm in depth, including consolidating and deposited layer by ramming
watering etc., disposing of surplus excavated soil as directed with in
a lead of 50 mm and lift upto 1.5 m.
16.66.1 All kind of soil each 26.45
16.67 Providing and fixing at or near ground level factory made RCC
pavement slab of M-30 grade of size 450x450x50 mm, including
reinforcement with 6 mm dia M.S. bars 4 nos on each side, including
setting in position in footpath to the required level and line over a bed
of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse
sand), having joint thickness not more than 5mm except on curve,
including filling of joints with same cement mortar and making grooves
etc. complete as per direction of Engineer-in-charge. sqm 1264.65
16.68 Providing and laying 60mm thick faciory made cement concrete
interlocking paver block of M -30 grade made by block making
machine with strong vibratory compaction, of approved size, design
& shape, laid in required colour and pattern over and including 50mm
thick compacted bed of coarse sand, filling the joints with line sand
etc. all complete as per the direction of Engineer-in-charge. sqm 859.35
16.69 Providing and laying at or near ground level factory made kerb stone
of M-25 grade cement concrete in position to the required line, level
and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse
sand), including making joints with or without grooves (thickness of
joints except at sharp curve shall not to more than 5mm), including
making drainage opening wherever required complete etc. as per
direction of Engineer-in-charge (length of finished kerb edging shall
be measured for payment). (Precast C.C. kerb stone shall be approved
by Engineer-in-charge). cum 8376.15

No.
16.70 Providing and fixing G.I. chain link fabric fencing of required width in
mesh size 50x50 mm including strengthening with 2 mm dia wire or
nuts, bolts and washers as required complete as per the direction of
Engineer-in-charge.
16.70.1 Made of G.I. wire of dia 4 mm sqm 797.20
16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to achieve
outer dia not less than 5 mm in required colour and shade sqm 825.30
16.71 Providing and fixing G.I. chain link fabric fencing of required width in
mesh size 25x25 mm made of G.I. wire of dia 3 mm including
strengthening with 2 mm dia wire or nuts, bolts and washers as
required complete as per the direction of Engineer-in-charge. sqm 909.60
16.72 Supplying and stacking of hard stone (for stone pitching) 22.5 cm
thick at site. cum 966.10
16.73 Dry stone pitching 22.5 cm thick laid in courses and required profile
with hammer dressed stones having no side less than 15 cm, with
minimum depth of 20 cm including preparing the bedding surface
etc. all complete. (Payment for Stone to be made separately). sqm 487.25
16.74 75 mm thick back filling for pitching including supplying of required
materials and consolidation etc. complete with :
16.74.1 Moorum sqm 73.90
16.74.2 Stone aggregate 20 mm nominal size sqm 162.25
16.74.3 Stone aggregate 40 mm nominal size sqm 158.15
16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed
concrete from batching plant. The ready mixed concrete shall be
laid and finished with screed board vibrator , vacuum dewatering
process and finally finished by floating, brooming with wire brush
etc. complete as per specifications and directions of Engineer-in-
charge. (The panel shuttering work shall be paid for separately).
(Note:- Cement content considered in this item is @ 330 kg/cum.
Excess/less cement used as per design mix is payable/ recoverable
separately). cum 8663.05
16.76 Deduct for using of M-20 grade concrete instead of M-25 grade
concrete in C.C. pavement. cum 188.30
16.77 Scarifying the existing bituminous road surface to a depth of 50 mm
and disposal of scarified material within all lifts and lead upto 1km
(by mechanical means). sqm 4.75
16.78 Construction of granular sub-base by providing close graded Material
conforming to specifications, mixing in a mechanical mix plant at
OMC, carriage of mixed material by tippers to work site, for all leads
& lifts, spreading in uniform layers of specified thickness with motor
grader on prepared surface and compacting with vibratory power roller
to achieve the desired density, complete as per specifications and
directions of Engineer-in-Charge.
16.78.1 With material conforming to Grade-I (size range 75 mm
to 0.075 mm) having CBR Value-30 cum 2517.70

No.
16.78.2 With material conforming to Grade-II (size range 53 mm

to 0.075 mm ) having CBR Value-25 cum 2637.30
16.78.3 With material conforming to Grade-III (size range 26.5
mm to 0.075 mm ) having CBR Value-20 cum 2474.60
16.79 Providing, laying, spreading and compacting graded stone aggregate
(size range 53 mm to 0.075 mm ) to wet mix macadam (WMM)
specification including premixing the material with water at OMC in
for all leads & lifts, laying in uniform layers with mechanical
paverfinisher in sub- base / base course on well prepared surface
and compacting with vibratory roller of 8 to 10 tonne capacity to
achievethe desired density, complete as per specifications and
directions of Engineer-in-Charge. cum 2641.40
16.80 Construction of dry lean cement concrete sub base over a prepared
sub-grade with coarse and fine aggregate conforming to IS:383, the
size of coarse aggregate not exceeding 25 mm, aggregate cement
ratio not to exceed 15:1, aggregate gradation after blending to be as
per specifications, cement content not to be less than 150 Kg/cum,
optimum moisture content to be determined during trial length
construction, concrete strength not to be less than 10 Mpa at 7
days, mixed in a batching plant, transported to site, for all leads &
lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory
roller, finishing and curing etc. complete as per direction of Engineer-
in- charge. cum 3881.85
16.81 Providing and erecting 2.00 metre high temporary barricading at site;
each panel of size 2.50mx2.00m made of 40x40x6mm angle
iron or 50x50x3mm hollow MS tube posts/horizontal members/
bracings covered with 1.63mm thick MS sheet. The sheet shall
be fixed with 30x5mm MS flat by suitable welding/riveting.
The panels shall be made so that gap of 50cm above the ground
is available making overall height as 2.5m. MS channel ISLC
75 @ 5.70 kg/m, 50cm long shall be provided at the bottom
having oval shaped holes of size 50x25mm at both ends with
50cm long MS angle 40x40x6mm bracing. Suitable
arrangement shall be made to fix the barricading to avoid
from overturning by providing 250mm long expansion fasteners
at both ends. The work shall be executed as per drawing/direction
of Engineer-in-Charge which includes writing and painting,
arrangement for traffic diversion such as traffic signals during
construction at site for day and night, glow lamps, reflective signs,
marking, flags, caution tape as directed by the Engineer-in-Charge.
The barricading provided shall be retained in position at site
continuously i/c shifting of barricading from one location to another
location as many times as required during the execution of the entire
work till its completion. Rate include its maintenance for damages,
painting, all incidentals, labour materials, equipments and works
required to execute the job. The barricading shall not be removed
without prior approval of Engineer-in-Charge.
(Note :- One time payment shall be made for providing barricading
from start of work till completion of work i/c shifting. The barricading
provided shall remain to be the property of the contractor on completion
of the work). metre 2566.70

No.
16.82 Taking out existing kerb stones of all types from footpath/ central
verge, including removal of mortar etc., disposal of unserviceable
material to the dumping ground, for which payment shall be made
separately and stacking of serviceable material within 50 metre lead
as per direction of Engineer-in-Charge. metre 28.05
16.83 Taking out existing CC interlocking paver blocks from footpath/ central
verge, including removal of rubbish etc., disposal of unserviceable
material to the dumping ground, for which payment shall be made
separately and stacking of serviceable material within 50 metre lead
as per direction of Engineer-in-Charge. sqm 94.05
16.84 Laying old cement cocrete interlocking paver blocks of any design/
shape laid in required line, level, curvature, colour and pattern over
and including 50 mm thick compacted bed of coarse sand, filling the
joints with fine sand etc. all complete as per the direction of Engineer-
in-charge. (Old CC paver blocks shall be supplied by the department
free of cost). sqm 324.20
16.85 Laying at or near ground level old kerb stones of all types in position
to the required line, level and curvature, jointed with cement mortar
1:3 (1 cement : 3 coarse sand), including making joints with or without
grooves (thickness of joints, except at sharp curve, shall not be
more than 5 mm), including making drainage opening wherever
required etc. complete as per direction of Engineer-in-charge. (Length
of finished kerb edging shall be measured for payment). (Old kerb
stones shall be supplied by the department free of cost) metre 82.95
16.86 Providing and laying gang saw cut 18 mm thick, mirror polished pre
moulded and pre polished machine cut granite stone of required size
and shape of approved shade, colour and texture in footpath, flooring
cut granite stone of required size and shape of approved shade,
colour and texture in footpath, flooring in road side plazas and similar
locations, laid over 20mm thick base of cement mortar 1:4 (1cement
: 4 coarse sand) including grouting the joints with white cement
mixed with matching pigment, epoxy touch ups etc. complete as
per direction of Engineer-in-Charge.
16.86.1 With granite stone of area less than 0.50 sqm. sqm 3725.90
16.87 Providing and laying gang saw cut 30 mm thick, mirror polished pre
moulded and pre polished machine cut granite stone of required size
and shape of approved shade, colour and texture in footpath, flooring
in road side plazas and similar locations, laid over 20mm thick base
of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting
the joints with white cement mixed with matching pigment, epoxy
touch ups etc. complete as per direction of Engineer-in-Charge.
16.87.1 With granite stone of area less than 0.50 sqm. sqm 4006.85
16.88 Providing and laying matt finished vitrified tile of size 100x100x16mm
having water absorption less than 0.5% and conforming to IS: 15622
of approved make in all colours and shades in out door floors such
as footpath, court yard multi models etc., laid on 20mm thick base
of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes &
patterns including grouting the joints with white cement mixed with
matching pigments etc. complete as direction of Engineer-in-Charge. sqm 1933.75

No.
16.89 Providing and laying matt finished vitrified tile of size 300x300x9.8mm
having with water absorption less than 0.5% and conforming to IS:
15622 of approved make in all colours and shades in for outdoor
floors such as footpath, court yard, multi modals location etc., laid
on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse
sand) in all shapes & patterns including grouting the joints with white
cement mixed with matching pigments etc. complete as per direction
of Engineer-in-Charge. sqm 1264.80
16.90 Providing and laying tactile tile (for vision impaired persons as per
standards) of size 300x300x9.8mm having with water absorption less
than 0.5% and conforming to IS:15622 of approved make in all colours
and shades in for outdoor floors such as footpath, court yard, multi
modals location etc., laid on 20mm thick base of cement mortar 1:4
(1 cement : 4 coarse sand) in all shapes & patterns including grouting
the joints with white cement mixed with matching pigments etc.
complete as per direction of Engineer-in-Charge. sqm 1933.75
16.91 Providing and laying factory made chamfered edge Cement Concrete
paver blocks in footpath, parks, lawns, drive ways or light traffic
parking etc, of required strength, thickness & size/ shape, made by
table vibratory method using PU mould, laid in required colour &
pattern over 50mm thick compacted bed of sand, compacting and
proper embedding/laying of inter locking paver blocks into the sand
bedding layer through vibratory compaction by using plate vibrator,
filling the joints with sand and cutting of paver blocks as per required
size and pattern, finishing and sweeping extra sand. complete all as
16.91.1 60mm thick cement concrete paver block of M-35 grade
with approved colour, design & pattern. sqm 884.75
16.91.2 80 mm thick C.C. paver block of M-30 grade with approved
color design and pattern. sqm 953.00
16.92 Providing and fixing 10x10x7.50 cm Granite stone block hand cut and
chisel dressed on top, for paving in floors, drains etc. laid over 20mm
thick base mortar 1:4 (1 cement : 4 coarse sand) with
joints 10mm wide filled with same mortar including ruled pointing etc.
complete as per direction of engineer-in-charge. sqm 1897.95
16.93 Providing and placing in position 100 mm thick factory made machine
batched & machine mixed Precast RCC Rectangular Covers on
drains of footpath of various sizes, of M-25 grade cement concrete
for RCC work, including cost of centering, shuttering, reinforcement
of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on
both ways , neat cement punning on finished surface, properly
encased on all edges with 1.6 mm thick , 100 mm wide MS sheet
duly painted over priming coat , reinforcement to be welded at edges
with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c
cost of cartage, all leads & lift, handling at site etc. all complete as
per direction of Engineer-in-Charge. sqm 2525.35
16.94 Providing & making Gabion structure with Mechanically Woven Double
Twisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS
16014:2012,MORTH Clause 2500, of required size, Mesh Type 10x12

No.
(D=100 mm with tolerance of ± 2%) Zinc coated, Mesh wire diameter

3.0 mm, mechanically edged/selvedged with partitions at every 1m
interval and shall have minimum 10 numbers of openings per meter
of mesh perpendicular to twist, tying with lacing wire of diameter
2.2mm, supplied @ 3% by weight of Gabion boxes, filled with boulders
with least dimension of 200 mm, as per drawing, all complete as per
direction of Engineer-in-charge. cum 3363.70
16014:2012,MORTH Clause 2500, of required size, Mesh Type
10x12(D=100 mm with tolerance of ± 2%) Zinic+PVC coated, Mesh
wire diameter2.7/3.7mm, mechanically edged/selvedged with
partitions at every 1m interval and shall have minimum 10 numbers
of openings per meter of mesh perpendicular to twist, tying with
lacing wire of diameter 2.2/3.2mm(ID/OD), supplied @3% by weight
of Gabion boxes, filled with boulders with least dimension of 200
mm, as per drawing, all complete as per directions of Engineer-in-
charge. cum 3584.45
16014:2012,MORTH Clause 2500, of required size, Mesh Type
10x12(D=100 mm with tolerance of ±2%), Zinic+10% Al alloy+PVC
coated, Mesh wire diameter 2.7/3.7mm (ID/OD), mechanically edged/
selvedged with partitions at every 1m interval and shall have minimum
10 numbers of openings per meter of mesh perpendicular to twist,
tying with lacing wire of diameter 2.2/3.2mm(ID/OD), supplied @3%
by weight of Gabion boxes, filled with boulders with least dimension
of 200 mm, as per drawing, all complete as per directions of Engineer-
in-charge. cum 4099.55

SUB HEAD : 17.0
SANITARY INSTALLATIONS
289
BASIC RATES (17.0 SANITARY INSTALLATIONS)

No.

0128 Mate day 617.00
0834 Synthetic enamel paint in all shades except black or chocolate
shade litre 160.00
1309 C.I. bracket for wash basin and sinks pair 88.00
1313 8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre
long with S.S. tringular plate for Eureopean type W.C. each 200.00
1330 Clamps and M.S. stays including bolts and nuts for 100 mm pipe each 67.50
1331 M.S. Holder bat clamp of approved design for 100 mm S.C.I. pipe each 30.00
1350 Mosquito proof coupling of approved design each 30.00
1369 S.C.I. gully or nahani grating 100 mm dia each 25.00
1373 Rubber insertions for 75 mm dia pipe joints each 16.00
SUB HEAD : 17.0 SANITARY INSTALLATIONS 290

No.
1392 Mirror of superior make glass 60x45 cm each 400.00
1396 Vitreous china pedestal for wash basin each 900.00
1397 Pig lead kg 176.00
1532 Flush pipe with union spreaders and clamps all in C.P. brass for
single stall each 270.00
double stall each 400.00
range of three stall each 520.00
range of four stall each 600.00
1540 Flush pipe and spreaders G.l. for single set of one squatting plate
urinal each 175.00
1541 Flush pipe and spreaders G.l. for range of two squatting plates
urinal each 250.00
1542 Flush pipe and spreaders G.l. for range of three squatting plates
urinal each 300.00
1543 Flush pipe and spreaders G.l. for range of four squatting plates
urinal each 390.00
1614 G.I. inlet connection each 60.00
1616 S.C.I. soil, waste and vent single socketed pipe 1.80 metres long:
75 mm dia each 1050.00
100 mm dia each 1135.00
1620 S.C.I. plain bend 75 mm dia each 210.00
1624 S.C.I. bend with access door 75 mm dia each 240.00
1627 S.C.I. plain single equal junctions 75x75x75 mm dia each 278.00
1630 S.C.I. single equal junctions 75x75x75 mm dia with access door each 320.00
1631 S.C.I. single equal junctions 100x100x100 mm dia with access
door each 405.00
1633 S.C.I. plain double equal junctions 75x75x75x75 mm dia each 382.00
1636 S.C.I. double equal junctions 75x75x75x75 mm dia with access
door each 500.00
1637 S.C.I. double equal junctions 100x100x100x100 mm dia with
access door each 715.00
1639 Slotted cowl (terminal guard) 75 mm dia each 191.00

No.

1653 Sand cast iron S&S plain single unequal junctions: 100x100x
1656 Sand cast iron S&S single unequal junctions: 100x100x75 mm dia
with access door each 550.00
1659 Sand cast iron S&S plain double unequal junctions: 100x100x75x
1662 Sand cast iron S&S double unequal junctions: 100x100x75x75 mm
dia with access door each 700.00
1666 Sand cast iron heel rest bend 75 mm dia each 274.00
1669 S.C.I. single equal invert branch of required degree 75x75x75 mm dia each 320.00
1670 S.C.I. single equal invert branch of required degree 100x100x
1672 S.C.I. double equal invert branch of required degree 75x75x75x
1673 S.C.I. double equal invert branch of required degree 100x100x
100x100 mm dia each 550.00
1674 S.C.I. single unequal invert branch of required degree 100x100x
1677 S.C.I. double unequal invert branch of required degree 100x100x
75x75 mm dia each 570.00
1682 S.C.I. door pieces 75 mm dia each 283.00
1685 S.C.I. collar 75 mm dia each 177.00
1863 Fire clay kitchen sink: 600x450x250 mm each 1283.00
1871 White vitreous china laboratory sink 450x300x150 mm each 1500.00
1875 White plastic seat (solid) with lid C.P. brass hinges and rubber buffers each 400.00
1876 Black plastic seat (solid) with lid C.P. brass hinges and rubber buffers each 310.00
1881 Spun yarn kg 50.00
1885 15 mm C.P. brass tap each 207.00
1889 C.P. brass toilet paper holder of standard size each 225.00
1891 C.I. trap for standard urinal with vent arm with operating and other
couplings in C.P. brass: 50 mm dia each 170.00
1895 C.P. brass trap 40 mm dia each 300.00
1896 100 mm S.C.I. trap with vent heel each 320.00

No.
1897 100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet each 271.00
1913 Vitreous china lipped front urinal each 460.00
1915 Vitreous china squatting plate urinal each 1053.00
1947 Vitreous china flat back wash basin 630x450 mm each 725.00
1949 Vitreous china angle back wash basin 600x480 mm each 725.00
1951 C.P. brass waste 32 mm each 80.00
1955 Vitreous china pedestal type water closet each 1000.00
1965 White vitreous china dual purpose closet (Anglo Indian W.C.)
suitable for use as squatting pan or European type water closet
as per manufacturer's specifications each 2500.00
1966 Floor mounted white vitrous china double trap syphonic WC with
10 litre cistern and all fittings & fixtures,seat cover etc each 9500.00
3213 Vitreous china Surgeon type wash basin of size 660x460 mm each 1000.00
3228 600x120 mm glass shelf with anodised aluminium angle frame,
C.P. brass brackets and guard rail of standard size each 250.00
3617 C.P. Brass union 40mm dia each 200.00
3620 C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres
long:100 mm dia each 1200.00
3621 C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres
3624 S.C.I. S&S bends with access door 100 mm dia each 300.00
3628 S.C.I. S&S bend 100 mm dia each 265.00
3634 S.C.I. S&S heel rest sanitary bend 100 mm dia each 296.00
3640 S.C.I. S&S single equal junctions 100x100x100 mm each 472.00

No.
3644 S.C.I. S&S single equal junctions with access door 100x100x
100 mm each 495.00
3645 S.C.I. S&S single equal junctions with access door 75x75x75 mm each 373.00
3650 S.C.I. S&S double equal junctions 100x100x100x100 mm each 620.00
3654 S.C.I. S&S double equal junctions with access door 100x100x
100x100 mm each 615.00
3655 S.C.I. S&S double equal junctions with access door 75x75x75x
75 mm each 480.00
3660 S.C.I. S&S single unequal junctions 100x100x75 mm each 570.00
3664 S.C.I. S&S single unequal junctions with access door 100x100x
75 mm each 640.00
3670 S.C.I. S&S double unequal junctions 100x100x75x75 mm each 800.00
3674 S.C.I. S&S double unequal junctions with access door 100x100x
75x75 mm each 850.00
3681 S.C.I. S&S single equal invert branch of required degree 100x100x
3685 S.C.I. S&S double equal invert branch of required degree 100x100x
100x100 mm dia each 530.00
3690 S.C.I. S&S single unequal invert branch of required degree 100x
3695 S.C.I. S&S double unequal invert branch of required degree 100x
100x75x75 mm dia each 725.00
3699 S.C.I. S&S, 75 mm offset for 75 mm dia pipe each 225.00
3728 S.C.I. S&S door pieces 100 mm dia each 400.00
3733 S.C.I. S&S, Slotted Cowl (Terminal Guard) 100 mm each 264.00
3738 S.C.I. S&S, collars 100 mm each 279.00

No.

3749 Vitreous china toilet paper holder of standard size each 100.00
7005 Vitreous china 10 litres low level cistern without fittings each 715.00
7006 Vitreous china 10 litres low level cistern with fittings each 1240.00
7048 Rawl plug 50 mm (designation 10 nos) each 25.00
7072 Wall mounted water closet of size 780 x 370x690 mm each 6000.00
7073 Adjustable Vitreous China Cistern with fittings of flushing capacity
3 litre/ 6litre 9adjustibla to 4 litre/8litre) each 1900.00
7074 White Vetrious China Waterless Urinal of size 600x330x315 mm each 9650.00
7075 Cistern with fittings for Waterless Urinal each 2290.00
7076 Battery based infrared sensor operated white Vitreous Urinal of
aprox.size 610x390x370 mm each 4500.00
7095 Stainless steel kitchen sink with drain board 510 x 1040 mm
bowl depth 250 mm each 2480.00
7096 Stainless steel kitchen sink - with drain board 510 x 1040 mm
7097 Stainless steel kitchen sink - with drain board 510 x 1040 mm
7098 Stainless steel kitchen sink - with drain board 510x1040 mm
7101 Stainless steel kitchen sink - without drain board 610x510 mm
7104 Coloured Orissa pattern W.C. pan 580x440 mm each 1830.00
7105 Coloured Pedestal type W.C. pan 580x440 mm (European type) each 860.00
7106 Coloured Vitreous china 10 lit. low level cistern each 1050.00
7107 Coloured (other than black) solid P.V.C. seat in European W.C. pan each 390.00
7112 Circular shape 450 mm dia Mirror with Plastic moulded frame each 430.00
7113 Rectangular shape 453x357 mm Mirror with Plastic moulded frame each 290.00
7114 Oval shape 450x350 mm (outer dimensions) Mirror with Plastic
moulded frame each 340.00
7116 Hard board 6 mm thick sqm 115.00
7117 Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia
with length not less than 700 mm i/c PVC waste fittings each 25.00

No.
7118 Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia
7119 Flexible (coil shaped) PVC waste pipe for sink and wash basin
32mm dia with length not less than 700 mm i/c PVC waste fittings each 35.00
7120 Flexible (coil shaped) PVC waste pipe for sink and wash basin
40 mm dia with length not less than 700 mm i/c PVC waste fittings each 35.00
7121 Bottle Trap each 620.00
7122 CP Brass Single lever telephonic wall mixer of approved make each 4500.00
7123 Coloured High density polyethylene / poly propylene 10 lit. (full flush)
capacity controlled low level flushing cistern with fittings each 550.00
7126 White Vitreous china 10 litre (full flush) capacity controlled low level
flushing cistern with all fittings each 700.00
7127 Coloured Vitreous china 10 litre (full flush) capacity controlled low
level flushing cistern with all fittings each 1150.00
7358 Flushing Cistern P.V.C. 10 litre capacity (low level) (White) (with
fittings, accessories and flush pipe) each 575.00
7359 P.V.C. automatic flushing cistern 5 litre capacity each 470.00
7363 15 mm C.P. brass tap with elbow operation lever each 430.00
7364 White glazed fire clay draining board 600x450x25 mm each 525.00
7375 G.I. flush pipe and C.P. brass spreader including C.P. connecting
pipe Single lipped urinal each 445.00
pipe Range of two lipped urinals each 765.00
7377 G.i. flush pipe and C.P. brass spreader including C.P. connecting
pipe Range of three lipped urinals each 1050.00
pipe Range of four lipped urinals each 1430.00
7379 White vitreous china clay half stall urinal flat back 580x380x350 mm
or angle back 450x375x350 mm with waste fittings as per IS:2556 each 865.00
7406 PTMT pillar cock each 125.00
7491 PTMT - Waste Coupling 31/32 mm each 34.00
7493 PTMT - Bottle Trap 31/32 mm each 210.00
7503 PTMT Liquid Soap Container of 400 ml capacity each 105.00
7504 PTMT - Towel Ring 215x200x37 mm each 130.00
7505 PTMT - Towel Rail (450 mm long ) each 135.00
7506 PTMT - Towel Rail (600 mm long) each 165.00
7507 PTMT Shelf 450x124x36 mm each 200.00
7508 PTMT - Urinal Spreader 15 mm each 76.00

No.
7621 Hubless centrifugally cast (spun) iron pipes as per IS 15905 -

100 mm dia (3000 mm length pipe) metre 700.00
7622 Hubless centrifugally cast (spun) iron pipes as per IS 15905 -
75 mm dia (3000 mm length pipe) metre 570.00
7623 Hubless centrifugally cast (spun) iron plain bend as per IS 15905 -
100mm dia each 230.00
7625 Hubless centrifugally cast (spun) iron double equal plain junction
as per IS 15905 - 100x100x100x100 mm dia each 510.00
7626 Hubless centrifugally cast (spun) iron double equal plain junction
7627 Hubless centrifugally cast (spun) iron single equal plain junction
as per IS 15905 - 100x100x100 mm dia each 400.00
7628 Hubless centrifugally cast (spun) iron single equal plain junction
7629 Hubless centrifugally cast (spun) iron double unequal plain junction
7630 Hubless centrifugally cast (spun) iron single unequal plain junction
as per IS 15905 -100x100x75 mm dia each 375.00
7631 Hubless centrifugally cast (spun) iron double equal plain invert
branch as per IS 15905 - 100x100x100x100 mm dia each 625.00
7632 Hubless centrifugally cast (spun) iron single equal plain invert branch
7633 Hubless centrifugally cast (spun) iron single equal plain invert
branch as per IS 15905 - 75x75x75 mm dia each 260.00
7634 Hubless centrifugally cast (spun) iron single unequal plain invert
branch 45 degree as per IS 15905 - 100x100x75 mm dia each 430.00
7635 Hubless centrifugally cast (spun) iron 65 mm offset with 100 mm
dia pipe as per IS 15905 each 360.00
7639 Hubless centrifugally cast (spun) iron bend with access door -
100mm dia as per IS 15905 each 365.00
7640 Hubless centrifugally cast (spun) iron bend with access door -
75mm dia as per IS 15905 each 290.00
7641 Hubless centrifugally cast (spun) iron terminal guard (slotted
cowl) -100 mm dia as per IS 15905 each 270.00
7642 Hubless centrifugally cast (spun) iron trap with 100 mm inlet and
100 mm outlet as per IS 15905 each 540.00

No.
7643 Hubless centrifugally cast (spun) iron trap with 100 mm inlet
and 75 mm outlet as per IS 15905 each 385.00
7644 SS 304 grade shielded coupling with EPDM rubber gasket for
100mm dia Hubless centrifugally cast (spun) iron each 275.00
7645 SS 304 grade shielded coupling with EPDM rubber gasket for
75 mm dia Hubless centrifugally cast (spun) iron each 250.00
7805 Salem Stainless steel AISI - 304 (18/8) Orrisa pattern W.C. pan
724mm X 578 mm each 4500.00
7806 Salem Stainless steel AISI - 304 (18/8) Round basin 405mm X
355 mm each 1500.00
7807 Salem Stainless steel AISI - 304 (18/8) Wash basin 530mm X
345 mm each 2000.00
7808 Centrifugally cast (spun) iron S&S 100 mm inlet and 100 mm outlet each 450.00
7858 P.T.M.T. Urinal cock 15 mm dia each 106.50
9001 C.P. Brass Centre Hole Basin Mixer With Cast Spout each 1600.00

17.0 SANITARY INSTALLATIONS
No.
17.1 Providing and fixing water closet squatting pan (Indian type W.C.
pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with manually controlled
device (handle lever) conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the walls and
floors wherever required:
17.1.1 White Vitreous china Orissa pattern W.C. pan of size
580x440 mm with integral type foot rests each 5421.50
17.1.2 Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan
of size 585x480 mm with flush pipe and integrated type
foot rests each 9836.70
17.2 Providing and fixing white vitreous china pedestal type water closet
(European type W.C. pan) with seat and lid, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with manually controlled
device (handle lever), conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the walls and
floors wherever required :
17.2.1 W.C. pan with ISI marked white solid plastic seat and lid each 5260.95
17.2.2 W.C. pan with ISI marked black solid plastic seat and lid each 5140.55
17.3 Providing and fixing white vitreous china pedestal type water closet
(European type) with seat and lid, 10 litre low level white vitreous
china flushing cistern & C.P. flush bend with fittings & C.I. brackets,
40 mm flush bend, overflow arrangement with specials of standard
make and mosquito proof coupling of approved municipal design
complete, including painting of fittings and brackets, cutting and
making good the walls and floors wherever required :
17.3.1 W.C. pan with ISI marked white solid plastic seat and lid each 6685.00
17.3.2 W.C. pan with ISI marked black solid plastic seat and lid each 6564.60
17.4 Providing and fixing white vitreous china flat back or wall corner type
lipped front urinal basin of 430x260x350 mm and 340x410x265 mm
sizes respectively with automatic flushing cistern with standard flush
pipe and C.P. brass spreaders with brass unions and G.I clamps
making good the walls and floors wherever required :
17.4.1 One urinal basin with 5 litre white P.V.C. automatic
flushing cistern each 4982.25
17.4.2 Range of two urinal basins with 5 litre white P.V.C.
automatic flushing cistern each 7677.75
17.4.3 Range of three urinal basins with 10litre white P.V.C.
17.4.4 Range of four urinal basins with 10 litre white P.V.C.

No.
17.5 Providing and fixing white vitreous china flat back half stall urinal of
size 580x380x350 mm with white PVC automatic flushing cistern,
with fittings, standard size C.P. brass flush pipe, spreaders with
unions and clamps (all in C.P. brass) with waste fitting as per IS :
2556, C.I. trap with outlet grating and other couplings in C.P. brass,
including painting of fittings and cutting and making good the walls
and floors wherever required :
17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing
cistern each 9360.60
17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic
17.5.3 Range of three half stall urinals with 10 litre P.V.C.
17.5.4 Range of four half stall urinals with 10 litre P.V.C. automatic
17.6 Providing and fixing one piece construction white vitreous china
squatting plate with an integral longitudinal flushing pipe, white P.V.C.
automatic flushing cistern, with fittings, standard size G.I. / PVC
flush pipe for back and front flush with standard spreader pipes with
fittings, G.I clamps and C.P. brass coupling complete, including
painting of fittings and cutting and making good the walls and floors
etc. wherever required :
17.6.1 Single squatting plate with 5 litre P.V.C. automatic flushing
cistern each 7240.55
17.6.2 Range of two squatting plates with 5 litre P.V.C. automatic
17.6.3 Range of three squatting plates with 10 litre P.V.C.
17.6.4 Range of four squatting plates with 10 litre P.V.C. automatic
17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require:
17.7.1 White Vitreous China Wash basin size 630x450 mm with
a pair of 15 mm C.P. brass pillar taps each 3087.70
a single 15 mm C.P. brass pillar tap each 2751.30
a pair of 15 mm C.P. brass pillar taps each 2846.90
17.7.4 White Vitreous China Flat back wash basin size 550x
400 mm with single 15 mm C.P. brass pillar tap each 2510.45
17.7.5 White Vitreous China Angle back wash basin size 600 x
480 mm with single 15mm C.P. brass pillar tap each 2751.30
17.7.6 White Vitreous China Angle back wash basin size 400 x
400 mm with single 15 mm C.P. brass pillar tap each 2349.90

No.
17.7.7 White Vitreous China Flat back wash basin size 450x
300 mm with single 15mm C.P. brass pillar tap each 2196.05
17.7.8 White Vitreous China Surgeon type wash basin of size
660x460 mm with a pair of 15 mm C.P. brass pillar taps
with elbow including operated levers each 4052.35
17.7.9 White Vitreous China Surgeon type wash basin of size
660x460 mm with single 15 mm C.P. brass pillar taps
with elbow operated levers ISI Marked each 3417.55
17.7.10 Stainless Steel AISI-304(18/8) Round basin 405x355 mm
with single 15 mm C.P. brass pillar tap each 3788.20
17.7.11 Stainless Steel AISI-304(18/8) Wash basin 530x345 mm
with single 15 mm C.P. brass pillar tap each 4457.15
17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP
Brass single hole basin mixer of approved quality and make, including
wherever required:-
(a) White Vitreous China Wash basin size 550x400 mm with a
15 mm CP Brass single hole basin mixer each 4403.80
17.7B Providing and fixing wash basin with C.I. brackets, 15 mm PTMT
pillar cock, 32 mm PTMT waste coupling of standard pattern, including
wherever required. White Vitreous China Flat back wash basin size
550x400 mm with single 15 mm PTMT pillar cock. each 2398.70
17.8 Providing and fixing white vitreous china pedestal for wash basin
completely recessed at the back for the reception of pipes and fittings. each 1420.15
17.9 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain
with rubber plug, 40 mm C.P. brass waste complete, including painting
the fittings and brackets, cutting and making good the walls wherever
required:
17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 mm each 3163.25
17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as
per IS:13983 with C.I. brackets and stainless steel plug 40 mm,
including painting of fittings and brackets, cutting and making good
the walls wherever required :
17.10.1 Kitchen sink with drain board
17.10.1.1 510x1040 mm bowl depth 250 mm each 5155.95
17.10.2 Kitchen sink without drain board

No.
17.11 Providing and fixing white vitreous china laboratory sink with C.I.
brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste
and 40mm C.P. brass trap with necessary C.P. brass unions complete,
including painting of fittings and brackets, cutting and making good
the wall wherever required :
17.11.1 Size 450x300x150 mm each 4122.55
17.11.2 Size 600x450x200 mm each 5460.45
17.12 Providing and fixing draining board with C.I. brackets including painting
of brackets, cutting and making good the walls wherever required :
17.12.1 White glazed fire clay draining board of size 600x450x
25 mm each 1337.80
17.13 Providing and fixing white vitreous china water closet squatting pan
(Indian type) :
17.13.1 Long pattern W.C. pan of size 580 mm each 1541.05
17.13.2 Orissa pattern W.C. pan of size 580x440 mm each 2544.50
17.14 Extra for using coloured W.C. pan instead of white W.C. pan :
17.14.1 Orissa pattern W.C. pan 580x440 mm each 842.90
17.15 Providing and fixing white vitreous china pedestal type (European
type/ wash down type) water closet pan. each 2276.95
17.16 Extra for using coloured pedestal type W.C pan (European type)
with low level cistern of same colour instead of white vitreous china
W.C pan and cistern. each 260.90
17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto
1 metre long with S.S. triangular plate to Eureopean type W.C. of
quality and make as approved by Engineer - in - charge. each 297.55
17.17 Providing and fixing a pair of white vitreous china foot rests of standard
pattern for squatting pan water closet :
17.17.1 250x130x30 mm pair 214.60
17.17.2 250x125x25 mm pair 214.60
17.18 Providing and fixing P.V.C. low level flushing cistern with manually
controlled device (handle lever) conforming to IS : 7231, with all fittings
and fixtures complete.
17.18.1 10 litre capacity - White each 999.95
17.18.2 10 litre capacity - coloured each 971.40
17.19 Providing and fixing controlled flush, low level cistern made of vitreous
china with all fittings complete.
17.19.1 10 litre (full flush) capacity-white each 1839.70
17.19.2 10 litre (full flush) capacity-coloured each 2441.80
17.20 Providing and fixing solid plastic seat with lid for pedestal type W.C.
pan complete :
17.20.1 White solid plastic seat with lid each 571.00
17.20.2 Black solid plastic seat with lid each 450.60
17.20.3 Coloured (other than black & white) solid plastic seat
with lid each 557.65
No.
17.22 Providing and fixing G.I. inlet connection for flush pipe connecting
with W.C. pan. each 116.10
17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved
quality & make and as per the direction of Engineer-in-charge. each 883.05
17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of
quality & make as approved by Engineer in charge.
(a) 15 mm nominal dia each 6113.60
17.23 Providing and fixing white vitreous china flat back or wall corner type
lipped front urinal basin of 430x260x350 mm or 340x410x265 mm
sizes respectively. each 1299.75
17.24 Providing and fixing white vitreous china squatting plate urinal with
integral rim longitudinal flush pipe. each 3207.50
17.25 Providing and fixing white vitreous china wash basin including making
all connections but excluding the cost of fittings :
17.25.1 Flat back wash basin of size 630x450 mm each 1139.40
17.25.3 Angle back wash basin of size 600x480 mm each 1139.40
17.25.4 Angle back wash basin of size 400x400 mm each 738.05
17.25.6 Surgeon type wash basin of size 660x460 mm each 1507.35
17.26 Providing and fixing kitchen sink including making all connections
excluding cost of fittings.
17.26.1 White glazed fire clay sink of size 600x450x250 mm each 1853.65
17.27 Providing and fixing white vitreous china laboratory sink including
making all connections excluding cost of fittings :
17.27.1 Size 450x300x150 mm each 2143.95
17.27.2 Size 600x450x200 mm each 3481.90
17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including
P.V.C. waste fittings complete.
17.28.1 Semi rigid pipe
17.28.1.1 32 mm dia each 87.70
17.28.1.2 40 mm dia each 98.40
17.28.2 Flexible pipe
17.28.2.1 32 mm dia each 101.10
17.28.2.2 40 mm dia each 101.10
17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. each 44.60
17.30 Providing and fixing in position 25 mm diameter mosquito proof
coupling of approved municipal design. each 45.00
17.31 Providing and fixing 600x450 mm beveled edge mirror of superior
glass (of approved quality) complete with 6 mm thick hard board
ground fixed to wooden cleats with C.P. brass screws and washers
complete. each 1283.05

No.
17.32 Providing and fixing mirror of superior glass (of approved quality) and
of required shape and size with plastic moulded frame of approved
make and shade with 6 mm thick hard board backing :
17.32.1 Circular shape 450 mm dia each 1242.00
17.32.2 Rectangular shape 453x357 mm each 1120.25
17.32.3 Oval shape 450x350 mm (outer dimensions) each 1185.60
17.32.4 Rectangular shape 1500x450 mm each 1786.55
17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off,
supported on anodised aluminium angle frame with C.P. brass
brackets and guard rail complete fixed with 40 mm long screws, rawl
plugs etc., complete. each 841.80
17.34 Providing and fixing toilet paper holder :
17.34.1 C.P. brass each 583.75
17.34.2 Vitreous china each 426.15
17.35 Providing and fixing soil, waste and vent pipes :
17.35.1 100 mm dia
17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 metre 1008.20
17.35.1.2 Centrifugally cast (spun) iron socket &
spigot (S&S) pipe as per IS: 3989 metre 1092.20
17.35.1.3 Hubless centrifugally cast (spun) iron
pipes epoxy coated inside & outside
IS:15905 metre 1051.75
17.35.2 75 mm diameter :
17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 metre 923.25
17.35.2.2 Centrifugally cast (spun) iron socketed pipe
as per IS: 3989 metre 992.05
IS:15905 metre 859.55
17.36 Providing and filling the joints with spun yarn, cement slurry and
cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :
17.36.1 75 mm dia pipe each 126.00
17.36.2 100 mm dia pipe each 148.45
17.37 Providing and fixing M.S. holder-bat clamps of approved design to
Sand Cast iron/cast iron (spun) pipe embedded in and including
cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size),
including cost of cutting holes and making good the walls etc. :
17.37.1 For 100 mm dia pipe each 287.45
17.37.2 For 75 mm dia pipe each 283.40

No.
17.38 Providing and fixing bend of required degree with access door, insertion
rubber washer 3 mm thick, bolts and nuts complete.
17.38.1 100 mm dia
17.38.1.1 Sand cast iron S&S as per IS - 1729 each 461.65
17.38.1.3 Hubless centrifugally cast (spun) iron epoxy
coated inside & outside as per IS:15905 each 548.60
17.38.2 75 mm dia
17.38.2.2 Sand cast iron S&S as per IS- 3989 each 384.75
17.39 Providing and fixing plain bend of required degree.
17.39.1 100 mm dia
17.39.1.2 Sand cast iron S&S as per IS : 3989 each 390.75
17.39.1.3 Hubless centrifugally cast (spun) iron pipes
epoxy coated inside & outside IS:15905 each 343.90
17.39.2 75 mm dia
17.39.2.1 Sand cast iron S&S as per IS -1729 each 309.85
17.39.2.3 Hubless centrifugally cast (spun) iron pipes
epoxy coated inside & outside IS:15905 each 242.95
17.40 Providing and fixing heel rest sanitary bend
17.40.1 100 mm dia
17.40.2 75 mm dia
17.41 Providing and fixing double equal junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete :
17.41.1 100x100x100x100 mm
17.41.2 75x75x75x75 mm

No.
17.42 Providing and fixing double equal plain junction of required degree.
17.42.1 100x100x100x100 mm
IS:15905 each 718.55
17.42.2 75x75x75x75 mm
IS:15905 each 396.80
17.43 Providing and fixing single equal plain junction of required degree
with access door, insertion rubber washer 3 mm thick, bolts and
nuts complete.
17.43.1 100x100x100 mm
17.43.2 75x75x75 mm
17.44 Providing and fixing single equal plain junction of required degree :
17.44.1 100x100x100 mm
epoxy coated inside & outside as per
IS:15905 each 571.35
17.44.2 75x75x75 mm
17.45 Providing and fixing double unequal junction of required degree with
complete:
17.45.1 100x100x75x75 mm

No.
17.46 Providing and fixing double unequal plain junction of required

degree :
17.46.1 100x100x75x75 mm
17.47 Providing and fixing single unequal junction of required degree with
complete :
17.47.1 100x100x75 mm
17.48 Providing and fixing single unequal plain junction of required
degree :
17.48.1 100x100x75 mm
17.49 Providing and fixing double equal plain invert branch of required degree:
17.49.1 100x100x100x100 mm
17.49.1.2 Sand cast iron S&S as per IS 3989 each 745.30
17.49.2 75x75x75x75 mm
17.50 Providing and fixing single equal plain invert branch of required
degree :
17.50.1 100x100x100 mm
17.50.1.1 Sand cast iron S&S as per iron 1729 each 584.75
17.50.2 75x75x75 mm

No.
17.51 Providing and fixing double unequal invert branch of required

degree :
17.51.1 100x100x75x75 mm
17.52 Providing and fixing single unequal plain invert branch of required
degree :
17.52.1 100x100x75 mm
17.53 Providing and fixing sand cast iron S&S off sets as per IS: 1729
17.53.1 76 mm off sets
17.53.1.1 With 75 mm dia pipe each 320.55
17.53.2 114 mm off sets
17.53.3 152 mm off sets
17.53A Providing and fixing Hubless centrifugally cast iron offsets epoxy
coated inside & outside as per IS:15905
17.53A.1 65 mm offsets
17.53A.1.1 With 100 mm dia pipe each 510.55
17.53A.1.2 With 75 mm dia pipe each 423.55
17.54 Providing and fixing sand cast iron S&S off sets as per IS: 3989 :
17.54.1 75 mm off sets
17.54.2 150 mm off sets
17.54A Providing and fixing Hubless centrifugally cast iron offsets epoxy
coated inside & outside as per IS:15905
17.54A.1 130 mm offsets
17.54A.1.1 With 100 mm dia each 624.85
17.54A.1.2 With 75 mm dia each 443.65

No.
17.55 Providing and fixing door piece, insertion rubber washer 3mm thick,
bolts & nuts complete :
17.55.1 100 mm
17.55.2 75 mm
17.56 Providing and fixing terminal guard :
17.56.1 100 mm
17.56.2 75 mm
17.57 Providing and fixing collar :
17.57.1 100 mm
17.57.2 75 mm
17.57A Providing and fixing shielded coupling for Hubless centrifugally cast
iron pipe
17.57A.1 100 mm dia
17.57A.1.1 SS 304 grade coupling with EPDM rubber
gasket each 404.10
17.57A.2 75 mm dia
17.57A.2.1 SS 304 grade coupling with EPDM rubber
gasket each 363.35
17.58 Providing lead caulked joints to sand cast iron/centrifugally cast
(spun) iron pipes and fittings of diameter :
17.58.1 100 mm each 481.45
17.58.2 75 mm each 407.90
17.58.3 50 mm each 329.50

No.
17.59 Providing and fixing M.S. stays and clamps for sand cast iron/
centrifugally cast (spun) iron pipes of diameter :
17.59.1 100 mm each 126.50
17.59.2 75 mm each 78.40
17.59.3 50 mm each 72.20
17.60 Providing and fixing trap of self cleansing design with screwed down
or hinged grating with or without vent arm complete, including cost of
cutting and making good the walls and floors :
17.60.1 100 mm inlet and 100 mm outlet
17.60.1.1 Sand cast iron S&S as per IS: 3989 each 1512.55
17.60.1.2 Sand Cast Iron S&S as per IS: 1729 each 1273.05
17.60.2 100 mm inlet and 75 mm outlet
17.60.2.2 Sand Cast Iron S&S as per IS- 1729 each 1202.15
17.61 Cutting chases in brick masonry walls for following diameter sand
cast iron/centrifugally cast (spun) iron pipes and making good the
same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6
graded stone aggregate 12.5 mm nominal size), including necessary
plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse
sand) :
17.61.1 100 mm dia metre 555.30
17.61.2 75 mm dia metre 398.70
17.61.3 50 mm dia metre 259.05
17.62 Painting C.I. cistern with bitumastic or any other anti-corrosive paint
inside and white paint over a coat of zinc chromate yellow primer (of
approved quality ) on the outside surface of the cistern, flush pipe,
other fittings, etc. complete for new work. each 768.15
17.63 Re-painting C.I. cistern with bitumastic or any other anti-corrosive
paint inside and white paint on the outside surface of the cistern,
flush pipe, other fittings, etc. complete, including polishing of wooden
seat and lid and cleaning of W.C. pan with acid wherever necessary. each 516.35
17.64 Repainting C.I. cistern with synthetic enamel paint of approved colour,
brand and manufacture on the outside surface of cistern, flush pipe,
other fittings etc. complete. each 223.90

No.
17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste
vent pipes and fittings with two coats of synthetic enamel paint of
any colour such as chocolate grey, or buff etc. over a coat of primer
(of approved quality) for new work :
17.65.1 100 mm diameter pipe metre 64.20
17.66 Repainting sand cast iron/ centrifugally cast iron (spun) iron, soil,
waste, vent pipes and fittings with one coat of synthetic enamel
paint of any colour such as chocolate, grey or buff etc :
17.67 Repainting bath tub of size 1700x730x430 mm with enamel paint. each 630.55
17.68 Providing and fixing vitreous china dual purpose closet suitable for
use as squatting pan or European type water closet (Anglo Indian
W.C pan) with seat & lid fixed with C.P. brass hinges and rubber
buffers, 10 litre low level flushing cistern with fitting and brackets, 40
mm flush bend, 20 mm over flow pipe, with specials of standard
make and mosquito proof coupling of approved municipal design
making good the walls and floors wherever required:
17.68.1 White vitreous china dual purpose WC pan with white
solid plastic seat and lid with white vitreous china flushing
cistern and C.P. flush bend. each 10023.90
17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink,
of approved quality and colour.
17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm
breadth weighing not less than 45 gms each 99.75
17.69.2 Waste coupling 38 mm dia of 83 mm length and 77mm
breadth, weighing not less than 60 gms each 118.50
17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.
17.70.1 Bottle trap 31mm single piece moulded with height of
270 mm, effective length of tail pipe 260 mm from the
centre of the waste coupling, 77 mm breadth with 25 mm
minimum water seal, weighing not less than 260 gms each 335.25
17.70.2 Bottle trap 38 mm single piece moulded with height of
270 mm, effective length of tail pipe 260 mm from the
centre of the waste coupling, 77 mm breadth with 25 mm
minimum water seal, weighing not less than 263 gms each 348.60
17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125
mm high and 112 mm distance from wall of standard shape with
bracket of the same materials with snap fittings of approved quality
and colour, weighing not less than 105 gms. each 158.55

No.
17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,
200 mm wide with minimum distances of 37 mm from wall face with
concealed fittings arrangement of approved quality and colour,
weighing not less than 88 gms. each 228.20
17.73 Providing and fixing PTMT towel rail complete with brackets fixed to
wooden cleats with CP brass screws with concealed fittings
arrangement of approved quality and colour.
17.73.1 450 mm long towel rail with total length of 495 mm,
78 mm wide and effective height of 88 mm, weighing not
less than 170 gms each 555.35
17.73.2 600 mm long towel rail with total length of 645 mm, width
78 mm and effective height of 88 mm, weighing not less
than 190 gms. each 595.50
17.74 Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36
mm height of approved quality and colour, weighing not less than
300 gms. each 642.30
17.75 Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100
mm with 1/2" BSP thread and shapes, weighing not less than 60
gms. each 119.75
17.76 Providing and fixing PTMT urinal cock of approved quality and colour.
17.76.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mm
wide with BSP female threads weighing not less than 48
gms each 164.05
17.77 Providing and fixing M.S. holder bat clamp of approved design to
sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets
made of 50x5 mm flat of specified shape, projecting 75 mm outside
the wall surface and fixed on wall with 4nos, 6mm dia expansion
hold fasteners, including drilling necessary holes in brick wall/ CC/
RCC surface and the cost of bolts etc. The pipes shall be fixed to the
already fixed brackets with the help of 30 mm x1.6 mm galvanised
M.S. flats of specified shape and of total length 420 mm and shall be
fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts
on each side of the pipe.
17.77.1 Total bracket length 580 mm of approved shape and design
(for single 100 mm dia pipe) each 247.80
17.77.2 Total bracket length 810 mm of approved shape and design
(for two 100 mm dia pipes) each 302.35
17.77.3 Total bracket length 1040 mm of approved shape and
design (for three 100 mm dia pipes) each 356.70
17.78 Providing and fixing white vitreous china extended wall mounting
water closet of size 780x370x690 mm of approved shape including
providing & fixing white vitreous china cistern with dual flush fitting,
of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres),
including seat cover, and cistern fittings, nuts, bolts and gasket etc

No.
17.79 Providing & fixing white vitreous china water less urinal of size 600 x
330 x 315 mm having antibacterial /germs free ceramic surface,
fixed with cartridge having debris catcher and hygiene seal. each 16868.15
17.80 Providing and fixing white vitreous china battery based infrared sensor
operated urinal of approx. size 610 x 390 x 370 mm having pre &
post flushing with water (250 ml & 500 ml consumption), having
water inlet from back side, including fixing to wall with suitable
brackets all as per manufacturers specification and direction of
Engineer-in-charge. each 6913.90
17.81 Providing and fixing floor mounted, white vitreous china single piece,
double traps syphonic water closet of approved brand/make, shape,
size and pattern including integrated white vitreous china cistern of
capacity 10 litres with dual flushing system, including all fittings and
fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc
including making connection with the existing P/S trap, complete in
all respect as per directions of Engineer-in-Charge. each 15457.95

SUB HEAD : 18.0
WATER SUPPLY
314
BASIC RATES (SH: 18.0 WATER SUPPLY)
No.
0010 Hire charges of derrick monkey rope day 750.00
0593 C.P. Brass Extension Nipple (1/2"x2" size) each 40.00
1304 Surface box for stop cock each 125.00
1305 Surface box for sluice valve each 210.00
1307 Surface box for water meter each 250.00
1339 Brass bib-cock 15 mm dia each 210.00
1342 Brass stop-cock 15 mm dia each 210.00
1360 C.I. mouth, brass ferrule 15 mm dia each 140.00
1362 C.l. mouth, brass ferrule 25 mm dia each 220.00
1397 Pig lead kg 176.00
1464 S & S.C.I. standard specials upto 300 mm dia (heavy class) quintal 3600.00
1466 S & S.C.I. standard specials over 300 mm dia (heavy class) quintal 3700.00
SUB HEAD : 18.0 WATER SUPPLY 315

No.
1468 Flanged C.I. standard specials upto 300 mm dia (heavy class) quintal 5500.00
1470 Flanged C.I. standard specials over 300 mm dia (heavy class) quintal 5500.00
1472 Casing pipe 100 mm dia metre 335.00
1545 G.I. pipes 15 mm dia metre 91.00
1555 G.I. back (jam) nuts 25 mm dia each 15.00
1608 G.I. tees (equal) 25 mm each 50.00
1641 G.I. Union 15 mm nominal bore each 30.00
1649 Polyethylene water storage tank with cover and suitable locking
arrangement per litre 5.50
1687 Unplasticised P.V.C. connection pipe with brass union 30 cm long
15 mm bore each 30.00
1693 S.C.I. hand pump each 670.00
1878 Shower rose C.P. brass for 15 to 20 mm inlet 100 mm dia each 100.00
1882 Strainer brass 40 mm dia 1.5 metre long each 600.00
1922 H.P. or L.P. ball valve with polythene floats: 15 mm dia each 210.00

No.
1926 20 mm dia Gunmetal gate valve with wheel each 325.00
1927 Brass full way valve with C.I. wheel (screwed end) 25 mm dia each 350.00
1933 Gunmetal non-return valve-horizontal (screwed end) 25 mm dia each 330.00
1940 C.I. sluice valve (with caps) class I: 100 mm dia each 2410.00
1941 C.I. sluice valve (with caps) class I : 125 mm dia each 2600.00
1956 Bolts and nuts 16 mm dia 60 mm long each 11.00
2271 Carriage of G.I. pipes below 100 mm dia tonne 92.24
2272 Carriage of Stainless Steel pipes below 100 mm dia tonne 92.24
2309 Carriage of Cast Iron fittings tonne 92.24
2319 Carriage of Spun iron S & S pipes 100 mm dia 100 metre 226.82

No.
2329 Carriage of Spun iron S & S pipes 600mm dia 100 metre 3780.28
2330 Carriage of C.I. pipes 500 mm dia 100 metre 2520.19
2331 Carriage of R.C.C. pipes 900 mm dia 100 metre 5670.42
2341 Carriage of Pig lead tonne 92.24
2343 Carriage of Ductile Iron pipes (k7) 100 mm dia 100 metre 226.82
2344 Carriage of Cast iron pipes 150 mm dia 100 metre 378.03
3080 Gunmetal non-return valve - vertical (screwed end) 25 mm dia each 350.00
3311 C.I. sluice valve (with caps) class II : 100 mm dia each 2700.00

No.
3327 15 mm Battery Based Sensor Pillar Cock each 5800.00
7257 C.P. Brass bibcock 15 mm each 290.00
7258 C.P. Brass long nose bibcock 15 mm each 430.00
7259 C.P. Brass long body bibcock 15 mm each 385.00
7260 C.P. Brass stop cock (concealed) 15 mm each 430.00
7261 C.P. Brass angle valve 15 mm each 375.00
7400 15 mm PTMT bib cock each 71.00
7401 15 mm PTMT bib cock with flange (fancy) each 105.00
7402 15 mm PTMT bib cock long body with flange each 116.00
7403 15 mm dia PTMT stop cock (male thread) each 71.00
7405 20 mm dia PTMT stop cock each 97.00
7407 PTMT push cock 15 mm dia each 62.00
7408 PTMT push cock 12 mm dia 20 mm BSP each 57.00
7409 PTMT grating 100 mm dia each 20.00
7410 PTMT Pillar cock (fancy) 15 mm foam flow each 138.00
7411 125 mm grating with waste hole each 30.00
7412 Rectangular type with openable circular lid 150 mm size 18 mm
high with 100 mm dia (110 gm) each 118.00
7415 Double acting air valve 50 mm each 3715.00
7418 Water meter (including testing charges) 80 mm each 2030.00
7422 Dirt box strainer 80 mm each 2680.00
7495 PTMT Ball Cock 15mm complete with Epoxy Coated Aluminium
Rod & H.D. Ball each 100.00

No.
7500 PTMT Angle Stop cock with Flange 15 mm each 100.00
7501 PTMT Swiveling shower 15 mm each 70.00
7509 PTMT Soap Dish/Holder 138x102x75 mm each 84.00
7651 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 100 mm dia metre 765.00
7652 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 - 150 mm dia metre 1150.00
7655 Ductile Iron class K - 9 pipe Conforming to 1.S. 8329 - 300 mm dia metre 2750.00
7660 Ductile Iron class K -9 pipe Conforming to I.S. 8329 - 600 mm dia metre 7560.00
7666 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 100 mm dia each 29.00

No.
7682 Ductile Iron K - 12 specials suitable for push on jointing up to
600 mm dia quintal 12400.00
7683 Ductile Iron K - 12 specials suitable for push on jointing over
600 mm dia quintal 17200.00
7684 Ductile Iron specials suitable for mechanical jointing as per
I.S. 9523 - up to 600 mm dia quintal 13050.00
7685 Ductile Iron Specials suitable for mechanical jointing as per
I.S. 9523 over 600 mm dia quintal 18750.00
7686 Ductile Iron Pipe Class K-9 flanges and welding 100 mm dia metre 1100.00
7697 S&S Centrifugally (Spun) C.I. Pipe class LA 100 mm dia metre 857.00
7708 S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 suitable
for lead jointing up to 300 mm dia quintal 5190.00
for lead jointing over 300 mm dia quintal 6200.00
7710 S&S Centrifugally (Spun) C.I. Pipe specials suitable for mechanical
joint as per I.S. 13382 up to 300 mm dia quintal 8571.00
7711 S&S Centrifugally (Spun) C.I. Pipe Specials suitable for mechanical
joint as per I.S. 13382 over 300 mm dia quintal 9048.00

No.
7712 Screwed double flanged centrifugally cast (spun) C.I. Pipe of

Class B conforming to I.S. 1536, - 100 mm dia metre 1310.00
7720 Screwed double flanged centrifugally cast (spun) C./. Pipe of
7722 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 100 mm dia metre 800.00
7726 Ductile Iron Class K- 7 pipe conforming to i.S. 8329 - 300 mm dia metre 2250.00
7859 P.T.M.T. Bib cock with nozzle 15 mm each 154.50
7861 P.T.M.T. Stop cock (concealed) 15 mm each 133.50
7862 15 mm nominal bore and 30 cm length PVC connection pipe with
P.T.M.T. Nuts each 46.50
7864 P.T.M.T. extension nipple 15 mm dia each 30.00

No.

8300 1216 mm PE-AL-PE Composite pressure pipe metre 62.00
8306 PPR Union 20 mm each 48.00
8626 Poly propylene- Random - Co - Polymer (PPR) pipes PN-16
(SDR 7.4) - 20 mm Outer dia metre 43.27
(SDR 11) - 50 mm Outer dia metre 252.22
8636 Chlorinated Polyvinyl - chloride (CPVC) pipe 15 mm outer dia metre 48.55

No.
8642 Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia metre 793.30
8643 Chlorinated Polyvinyl - chloride (CPVC) pipe 75 mm inner dia metre 1031.05
8701 SS pipe 304 grades with press fit technology as per JIS 3448
standard 48.60 mm outer dia metre 610.00
8702 Coupling/Socket fittings for 15.88 mm outer dia SS pipe each 59.00
8791 Reducer for 22.22 mm X 15.88 mm outer Dia SS pipe each 103.00
8805 Reducer for48.60 mm X 42.70 mm outer Dia SS pipe each 410.00
8806 Slip Coupling / Socket 15.88 mm outer dia SS pipe each 47.00

No.
8812 Elbow 90° for 15.88 mm outer dia SS pipe each 58.00
8818 Reducing Elbow 90° for 22.22 mm X 15.88 mm outer dia SS pipe each 148.00
8824 Equal Tee for 15.88 mm outer dia SS pipe each 159.00
8830 Reducing Tee for 22.22 mm X 15.88 mm outer dia SS each 179.00
8831 Reducing Tee for 28.58 mm X 15.88 mm outer dia SS pipe each 273.00
8843 Reducing Tee for 48.60mm X 34.00 mm outer dia SS pipe each 887.00

No.
8844 Reducing Tee for 48.60mm X 42.70mm outer dia SS pipe each 887.00
8845 Stainless steel Male thread Tee for 15.88 mm outer dia X 15 mm
nominal dia threaded each 179.00
nomina dia threaded each 200.00
nomina dia threaded each 273.00

No.
8866 Stainless steel Female thread Tee for 15.88 mm outer dia X 15 mm
8887 Stainless steel Female threaded Connector/Adapter for 15.88 mm
outer dia X 15 mm nominal threaded each 190.00

No.

8899 Stainless steel Male threaded Connector/Adapter for 15.88 mm

No.
8910 Stainless steel Valve Connector for 15.88 mm outer dia X 15 mm

8917 SS Female Threaded Elbow 90o for 15.88 mm outer dia X 15 mm
8918 Stainless steel Female Threaded Elbow 90o for 22.22 mm
outer dia X 15 mm nominal dia threaded each 191.00
outer dia X40 mm nominal dia threaded each 478.00
8926 Stainless steel Male Threaded Elbow 90o for 15.88 mm
8927 Stainless steel Male Threaded Elbow 90o for 22.22 mm
8928 Stainless steel Male Threaded Elbow 900 for 22.22 mm
8930 Stainless steel MaleThreaded Elbow 900 for 34.00 mm

No.

8936 Stainless steel Cap for 15.88 mm outer dia pipe each 45.00
8942 Stainless steel Pipe Bridge for 15.88 mm outer dia pipe each 214.00

18.0 WATER SUPPLY
No.
PE-AL-PE COMPOSITE PRESSURE PIPE
18.1 Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-
PE Composite Pressure Pipes conforming to IS - 15450, U.V.
stabilized with carbon black having thermal stability for hot & cold
water supply, capable to withstand temperature up to 80°C, including
all special fittings of composite material (engineering plastic blend
and brass inserts wherever required) e.g. elbows, tees, reducers,
couplers & connectors etc., with clamps at 1.00 metre spacing.
This includes testing of joints complete as per direction of the
Engineer-in-charge.
INTERNAL WORK - EXPOSED ON WALL
18.1.1 1216 (16 mm OD) pipe metre 250.40
18.1.2 1620 (20 mm OD) pipe metre 292.75
18.1.3 2025 (25 mm OD) pipe metre 362.95
18.1.4 2532 (32 mm OD) pipe metre 468.95
18.1.5 3240 (40 mm OD) pipe metre 659.55
18.1.6 4050 (50 mm OD) pipe metre 824.80
18.2 Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-
couplers & connectors etc., with clamps at 1.00 metre spacing.
This includes the costs of cutting chases and including testing of
joints complete as per direction of the engineer in charge.
Concealed work, including cutting chases and making good the wall
etc.
18.2.1 1216 (16 mm OD) pipe metre 441.15
18.2.2 1620 (20 mm OD) pipe metre 478.60
18.2.3 2025 (25 mm OD) pipe metre 553.50
18.2.4 2532 (32 mm OD) pipe metre 663.55
18.3 Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-
couplers & connectors etc., with trenching, refilling and testing of
joints complete as per direction of the engineer in charge.
External work
18.3.1 1216 (16 mm OD) pipe metre 226.25

No.
18.3.2 1620 (20 mm OD ) pipe metre 254.05

18.3.3 2025 (25 mm OD ) pipe metre 309.70
18.3.4 2532 (32 mm OD ) pipe metre 391.45
18.3.5 3240 (40 mm OD ) pipe metre 547.70
18.3.6 4050 (50 mm OD ) pipe metre 712.95
PP-R PIPES
18.4 Providing and fixing 3 layer PP-R (Poly propylene Random
copolymer) pipes confirming to IS 15801, UV stabilized & anti
- microbial fusion welded, having thermal stability for hot &
cold water supply, including all PP - R plain & brass threaded
polypropylene random fittings, i/c fixing the pipe with clamps
at 1.00 m spacing. This includes testing of joints complete as
Internal Exposed on walls
18.4.1 PN - 16 Pipe, 20mm OD (SDR-7.4) metre 232.35
18.4.5 PN - 10 Pipe, 50mm OD (SDR-11) metre 638.90
copolymer) pipes confirming to IS:15801, UV stabilized & anti
- microbial fusion welded, having thermal stability for hot &
cold water supply, including all PP - R plain & brass threaded
polypropylene random fittings, i/c fixing the pipe with clamps
at 1.00 m spacing. This includes the cost of cutting chases and
making good the same including testing of joints complete as
Concealed work,including cutting chases and making good
the wall etc.
copolymer) pipes confirming to IS:15801 UV stabilized & anti -
microbial fusion welded, having thermal stability for hot & cold
water supply, including all PP - R plain & brass threaded
polypropylene random fittings, including trenching, refilling &
testing of joints complete as per direction of Engineer-in-Charge.
External work
18.6.2 PN - 16 Pipe, 25 mm OD (SDR-7.4) metre 236.30

No.
18.6.5 PN - 10 Pipe, 50 mm OD (SDR-11) metre 543.95

18.6A Providing and fixing PPR Unions
18.6A.1 PPR Union 20mm each 259.85
C.P.V.C. PIPES
18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and testing of joints complete
as per direction of Engineer in Charge.
Internal work - Exposed on wall
18.7.1 15 mm nominal outer dia Pipes metre 241.55
18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply, including all CPVC plain &
brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.
This includes jointing of pipes & fittings with one step CPVC solvent
cement and the cost of cutting chases and making good the same
including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls
etc.

No.
18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC
plain & brass threaded fittings This includes jointing of pipes & fittings
with one step CPVC solvent cement, trenching, refilling & testing of
joints complete as per direction of Engineer in Charge.
External work
18.9.7 62.50 mm nominal inner dia Pipes metre 1552.30
18.9.8 75 mm nominal inner dia Pipes metre 1965.85
18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps,
i/c cutting and making good the walls etc.
18.10.1 15 mm dia nominal bore metre 284.90
18.11 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,
i/c making good the walls etc. concealed pipe, including painting
with anti corrosive bitumastic paint, cutting chases and making good
the wall :
18.12 Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc.
External work

No.

18.13 Making connection of G.I. distribution branch with G.I. main of following
sizes by providing and fixing tee, including cutting and threading the
pipe etc. complete :
18.13.1 25 to 40 mm nominal bore each 673.45
18.13.2 50 to 80 mm nominal bore each 1432.75
18.14 Fixing water meter and stop cock in G.I. pipe line including cutting
and threading the pipe and making long screws etc. complete (cost
of water meter and stop cock to be paid separately). each 606.55
BRASS FITTINGS
18.15 Providing and fixing brass bib cock of approved quality :
18.15.1 15 mm nominal bore each 302.55
18.16 Providing and fixing brass stop cock of approved quality :
18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved
quality (screwed end) :
18.17.1A 20 mm nominal bore each 460.20
18.17.2 32 mm nominal bore. each 581.25
18.18 Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete :
18.19 Providing and fixing gun metal non- return valve of approved quality
(screwed end) :
18.19.1 25 mm nominal bore
18.19.1.1 Horizontal each 477.70
18.19.1.2 Vertical each 504.45

No.

18.19.4.2 Vertical each 1251.10
18.19.5.2 Vertical each 2057.35
18.19.6.2 Vertical each 3399.10
18.20 Providing and fixing brass ferrule with C.I. mouth cover including
boring and tapping the main :
18.21 Providing and fixing uplasticised PVC connection pipe with brass
unions :
18.21.1 30 cm length
18.21.1.1 15 mm nominal bore each 72.85
18.21.2 45 cm length
18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
18.22.1 100 mm diameter each 151.90
C.I./DUCTILE IRON PIPES & SPECIALS
18.23 Laying in position centrifugally cast (spun) iron S&S or flanged pipes
(excluding cost of pipe). quintal 264.25
18.24 Laying in position S&S or flanged C.I. special such as tees, bends,
collars, tapers and caps etc.(excluding cost of specials). quintal 491.50
18.25 Providing and laying S&S C.I. standard specials such as tees, bends,
collars, tapers, caps etc. (Heavy class):
18.25.1 Up to 300 mm dia quintal 5320.40
18.25.2 Over 300 mm dia quintal 5454.20

No.
18.26 Providing and laying flanged C.I. standard specials such as tees,
bends, collars, tapers, caps etc., suitable for flanged jointing as per
IS : 1538 :
18.26.2 Over 300 mm dia quintal 7862.50
18.27 Providing and laying S&S centrifugally cast (spun) iron pipes (Class
LA) conforming to IS - 1536 :
18.27.1 100 mm dia pipe metre 1201.95
18.27.2 125 mm dia pipe metre 1499.80
18.27.3 150 mm dia pipe metre 1810.75
18.27.4 200 mm dia pipe metre 3062.75
18.27.5 250 mm dia pipe metre 4002.00
18.27.6 300 mm dia pipe metre 5391.05
18.27.7 350 mm dia pipe metre 6472.60
18.27.8 400 mm dia pipe metre 8513.95
18.27.9 450 mm dia pipe metre 10308.85
18.27.10 500 mm dia pipe metre 11969.15
18.27.11 600 mm dia pipe metre 16722.75
18.28 Providing lead caulked joints to spun iron or C.I. pipes and specials,
including testing of joints but excluding the cost of pig lead :
18.28.1 100 mm diameter pipe each 374.80
18.29 Supplying pig lead at site of work. quintal 23560.05
18.30 Providing flanged joints to double flanged C.I./ D.I. pipes and specials,
including testing of joints :

No.

C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES
18.31 Providing and fixing C.I. sluice valves (with cap) complete with bolts,
nuts, rubber insertions etc. (the tail pieces if required will be paid
separately) :
18.31.1 100 mm diameter
18.31.1.1 Class I each 3977.60
18.31.1.2 Class II each 4426.05
18.31.2.1 Class I each 4318.95
18.31.2.2 Class II each 5182.20
18.31.3.1 Class I each 5836.60
18.31.3.2 Class II each 6442.35
18.31.4.1 Class I each 11357.75
18.31.4.2 Class II each 13376.85
18.31.5.1 Class I each 16566.40
18.31.5.2 Class II each 21527.85
18.31.6.1 Class I each 22942.10
18.31.6.2 Class II each 26861.85
18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in
cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I.
surface box 100x100 x75 mm (inside) with hinged cover fixed in cement
concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size), i/c necessary excavation, foundation
concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate
40mm nominal size ) and inside plastering with cement mortar 1:3 (1
cement : 3 coarse sand) 12mm thick, finished with a floating coat of
neat cement complete as per standard design :
18.32.1 With common burnt clay F.P.S.(non modular) bricks of
class designation 7.5 each 1582.45

No.
18.33 Constructing masonry Chamber 60x60x75 cm inside, in brick work

in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,
with C.I. surface box 100mm top diameter, 160 mm bottom diameter
and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4
mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
nominal size ) , i/c necessary excavation, foundation concrete 1:5:10
(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal
size) and inside plastering with cement mortar 1:3 (1 cement : 3
coarse sand) 12 mm thick, finished with a floating coat of neat cement
complete as per standard design :
in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,
with C.I. surface box 100 mm top diameter, 160 mm bottom diameter
and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4
mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size ), i/c necessary excavation, foundation concrete 1:5:10
(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal
size ) and inside plastering with cement mortar 1:3 (1 cement : 3
coarse sand) 12 mm thick, finished with a floating coat of neat cement
complete as per standard design :
18.35 Constructing masonry Chamber 120x120x100 cm inside, in brick
work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice
valve, with C.I. surface box 100 mm top diameter, 160 mm bottom
diameter and 180 mm deep ( inside) with chained lid and RCC top
slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) , i/c necessary excavation, foundation concrete
1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar 1:3 (1 cement
: 3 coarse sand) 12 mm thick, finished with a floating coat of neat
cement complete as per standard design :
18.36 Constructing masonry Chamber 60x60x75 cm, inside in brick work
in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants,
with C.I. surface box 350x350 mm top and 165 mm deep ( inside)
with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary
excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand:10
graded stone aggregate 40 mm nominal size) and inside plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick,
finished with a floating coat of neat cement complete as per standard
design :

No.

in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter
complete with C.I. double flap surface box 400x200x200 mm (inside)
with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c
necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5
fine sand:10 graded stone aggregate 40 mm nominal size) and inside
plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12
mm thick, finished with a floating coat of neat cement complete as
per standard design :
18.38 Painting G.I. pipes and fittings with synthetic enamel white paint
with two coats over a ready mixed priming coat, both of approved
quality for new work :
18.39 Repainting G.I. pipes and fittings with synthetic enamel white paint
with one coat of approved quality :
18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive
bitumastic paint of approved quality :

No.
18.41 Providing and filling sand of grading zone V or coarser grade, allround
the G.I. pipes in external work :
18.42 Boring with 100 mm diameter casing pipe for hand pump / tubewell,
in all soils except ordinary hard rocks requiring blasting, including
removing the casing pipe after the hand pump / tube well is lowered
and tested :
18.42.1 Up to 6 metres depth metre 554.20
18.42.2 Beyond 6 m and up to 12 m depth metre 656.20
18.42.3 Beyond 12 m and up to 18 m depth metre 761.55
18.43 Providing and placing in position filters of 40 mm diameter G.I. pipe
with brass strainer of approved quality. metre 768.55
18.44 Providing and fixing to filter and lowering to proper levels 40 mm G.I.
pipe for tube well including cleaning and priming the tube well. metre 433.95
18.45 Providing and placing in position hand pump of approved quality for
40 mm diameter G.I. pipe complete with all accessories. each 1117.80
18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading
the pipe and making long screws etc. complete (New work) :
18.47 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and
threading the pipe and making long screws, including excavation,
refilling the earth or cutting of wall and making good the same complete
wherever required :

No.

18.48 Providing and placing on terrace (at all floor levels) polyethylene water
storage tank, IS : 12701 marked, with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank. per litre 8.80
18.48A Providing and fixing rectangular high density polyethylene water
storage loft tank with cover, conforming to ISI : 12701, colour of
opaque white or as approved by Engineer-in-charge. The rate includes
making necessary holes for inlet, outlet & over flow pipes. The base
support i/c fittings & fixtures for tank shall be paid separately. per litre 8.80
C.P. BRASS FITTINGS
18.49 Providing and fixing C.P. brass bib cock of approved quality conforming
to IS:8931 :
18.50 Providing and fixing C.P. brass long nose bib cock of approved quality
conforming to IS standards and weighing not less than 810 gms.
18.51 Providing and fixing C.P. brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms.
18.52 Providing and fixing C.P. brass stop cock (concealed) of standard
design and of approved make conforming to IS:8931.
18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser
points of approved quality conforming to IS:8931
18.53.1 15mm nominal bore each 532.00
18.53A Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)
of approved make and quality as per direction of Engineer-in-charge. each 61.25
PTMT FITTINGS
18.54 Providing and fixing PTMT bib cock of approved quality and colour.
18.54.1 15mm nominal bore, 86 mm long, weighing not less than
88 gms each 116.55
18.54.2 15 mm nominal bore, 122mm long, weighing not less
than 99 gms each 162.05
18.54.3 15 mm nominal bore, 165 mm long, weighing not less

No.

18.55 Providing and fixing PTMT stop cock of approved quality and colour.
18.55.3 Concealed stop cock, 15 mm nominal bore, 108 mm
long, weighing not less than 108 gms each 200.20
18.56 Providing and fixing PTMT pillar cock of approved quality and colour.
18.56.2 15 mm nominal bore, 125 mm long foam flow, weighing
not less than 120 gms each 210.05
18.57 Providing and fixing PTMT, push cock of approved quality and colour.
18.58 Providing and fixing PTMT grating of approved quality and colour.
18.58.1 Circular type
18.58.1.1 100 mm nominal dia each 37.90
18.58.1.2 125 mm nominal dia with 25 mm waste hole each 51.25
18.58.2 Rectangular type with openable circular lid
18.58.2.1 150 mm nominal size square 100 mm
diameter of the inner hinged round grating each 169.00
AIR VALVE & WATER METER (BULK TYPE)
18.59 Providing and fixing C.I. double acting air valve of approved quality
with bolts, nuts, rubber insertions etc. complete (The tail pieces,
tapers etc if required will be paid separately) :
18.59.1 50 mm dia each 5157.00
18.59.2 80 mm dia each 6240.70
18.59.3 100 mm dia each 8193.10
18.60 Providing and fixing enclosed type water meter (bulk type) conforming
to IS : 2373 and tested by Municipal Board complete with bolts,
nuts, rubber insertions etc. (The tail pieces if required will be paid
separately) :
18.60.1 80 mm dia nominal bore each 3576.10

No.
18.61 Providing and fixing C.I. dirt box strainer for bulk type water meter
with nuts, bolts, rubber insertions etc. complete conforming to IS :
2373 :
18.61.1 80 mm dia each 4097.90
18.61.2 100 mm dia each 6585.50
18.61.3 150 mm dia each 8345.25
18.61.4 200 mm dia each 11644.65
18.62 Providing and fixing PTMT Ball cock of approved quality, colour and
make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D.
plastic ball.
18.63 Providing and fixing PTMT angle stop cock 15 mm nominal bore,
weighing not less than 85 gms each 155.35
18.64 Providing and fixing PTMT swivelling shower, 15 mm nominal bore,
18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm,
breadth 102mm, height of 75mm with concealed fitting arrangements,
weighing not less than 106 gms. each 130.50
18.66 Providing and laying S&S C.I. Standard specials such as tees, bends,
collars tapers and caps etc, suitable for flanged jointing as per IS :
1538 :
18.66.2 Above 300 mm dia quintal 8799.05
18.67 Providing and laying S&S C.I. Standard specials suitable for
mechanical jointing as per IS : 13382 :
18.68 Providing and laying D.I. specials of class K-12 suitable for push-on
jointing as per IS : 9523 :

No.
18.69 Providing and laying D.I. Specials of Class K - 12 suitable for

mechanical jointing as per IS : 9523 :
18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or
Ductile Iron Pipes including testing of joints and the cost of rubber
gasket :
18.70.1 100 mm dia pipes joint 91.65
18.71 Providing and laying Double Flanged (screwed / welded) Centrifugally
(Spun) Cast Iron, Class B (IS : 1536) :
18.71.1 100 mm dia C.I. Double Flanged Pipe metre 1827.10
18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron
Pipes conforming to IS : 8329 :
18.72.1 100 mm dia Ductile Iron Class K-7 pipes metre 1114.10

No.
18.73 Providing and laying Double Flanged (Screwed/ Welded) Centrifugally
(Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :
18.73.1 100 mm dia Ductile Iron Double Flanged metre 1532.35

No.

18.74 Providing and fixing unplasticised P.V.C. connection pipe with PTMT
Nuts, collar and bush of approved quality and colour.
18.74.1 15 mm nominal bore with 30cm length each 94.90
18.74.2 15 mm nominal bore with 45 cm length each 112.45
18.75 Providing and fixing PTMT extension nipple for water tank pipe, fittings
of approved quality and colour.
18.75.1 15 mm nominal bore, weighing not less than 32 gms each 49.20
18.75.2 20 mm nominal bore, weighing not less than 40 gms each 81.30
18.75.3 25mm nominal bore, weighing not less than 62 gms each 113.40
18.76 Cutting holes up to 30x30 cm in walls including making good the
same:
18.76.1 With common burnt clay F.P.S. (non modular) bricks each 327.25
18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing
drain pipe etc. and repairing the hole after insertion of drain pipe etc.
with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size), including finishing complete
so as to make it leak proof. each 344.60
18.78 Making chases up to 7.5x7.5 cm in walls including making good and
finishing with matching surface after housing G.I. pipe etc. metre 154.15
18.79 Making hole up to 20x20 cm and embedding pipes up to 150 mm
diameter in masonry and filling with cement concrete 1:3:6 (1 cement
: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)
including disposal of malba. metre 180.15
18.80 Disinfecting C.I. water mains by flushing with water containing
bleaching powder @ 0.5 gms per litre of water and cleaning the
same with fresh water, operation to be repeated three times including
getting the sample of water from the disinfected main tested in the
municipal laboratory.
18.80.1 80 mm diameter C.I. pipe 100 metre 1349.55

No.

18.81 Extra for every operation of disinfecting the C.I. main by flushing with
water containing bleaching powder @ 0.5 gms per litre of water and
cleaning the same with fresh water, including getting the samples of
water tested in the municipal laboratory :
18.82 Dismantling old C.I. pipes including excavation and refilling trenches
after taking out the pipes, breaking lead caulked joints, melting of
lead and making into blocks, including stacking of pipes at site lead
up to 50 metre:
18.82.1 80 mm diameter C.I. pipe metre 287.05
18.83 Labour for cutting C.I. pipe with steel saw.
18.83.1 80 mm diameter C.I. pipe each cut 108.90

No.

18.84 Providing & fixing chrome plated brass battery based infrared sensor
operated pillar cock, having foam flow technology.
18.85 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304
as per JIS standard 3448 complete with press type fitting (fitting
shall be paid for separately) i/c fixing of the pipe with clamps at 1.00
m spacing including cutting and making good the walls including
testing of joints complete as per direction of Engineer-in-charge.
(The pipe length inserted in the fitting shall not be measured for
payment)
Inernal work - Exposed on wall
18.85.1 15.88 mm outer dia pipe metre 325.20
18.85.2 22.22 mm outer dia Pipe metre 484.00
18.86 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304
as per JIS standard 3448 complete with press type fitting (fitting
shall be paid for separately) i/c fixing of the pipe with clamps at
1.00m spacing and also including cutting of chases and making
good the walls including testing of joints complete as per direction of
Engineer -in-charge. (The pipe length inserted in the fitting shall not
be measured for payment)
Internal work - Concealed Pipe
18.86.1 15.88 mm outer dia .Pipes. metre 478.65
18.86.2 22.22 mm Outer dia pipes metre 637.40
18.87 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile
or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge.

No.
Coupling/Socket
18.87.1 For 15.88 mm outer dia pipe each 78.95
providing and fixing required Stainless Steel Fitting of press fit design
required dia as per dirction of Engineer-in-charge.
Reducer
18.88.1 For 22.22 mm x 15.88 mm outer dia pipe each 137.80
Slip Coupling/ Socket

No.

Elbow 90°
18.90.1 For 15.88mm outer dia pipe each 77.60
Reducing Elbow 90°
18.91.1 For22.22 mm x 15.88 mm outer dia pipe each 198.00
Equal Tee

No.
Reducing Tee
Male Thread Tee
18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 239.50

No.
Female Thread Tee
18.95.1 For 15.88 mm outer dia x15 mm nominal dia threaded each 239.50
Female Thread Connector/ Adapter
18.96.2 For 22.22 mm outer dia x 15 mmnominal dia threaded each 307.75

No.
Male Thread Connector/ Adapter
Valve Connector

No.
Female Threaded Elbow 90°
Male Threaded Elbow 90°
Cap

No.
Pipe Bridge

SUB HEAD : 19.0
DRAINAGE
357
BASIC RATES (SH: 19.0 DRAINAGE)
No.
0362 Brick bats cum 450.00
1006 Mild steel square bars quintal 4500.00
1336 Clearing eye with chain and lid 100 mm dia each 44.00
1352 C.I. cover and frame 300x300 mm inside each 477.00
1353 C.I. cover without frame 300x300 mm inside i/c cover of 4.50 kg each 477.00
1354 Rectangular cover 455x610 mm with frame (low duty) each 1400.00
1355 Rectangular cover 455x610 mm without frame (low duty) each 910.00
1356 500 mm dia cover with frame (medium duty) each 4400.00
1357 500 mm dia cover without frame (medium duty) each 2300.00
1364 C.I. grating 100x100 mm each 40.22
1617 S.C.I. soil, waste and vent single socketed pipe 1.80 metres
1618 S.C.I. soil, waste and vent single socketed pipe 1.80 metres
1700 R.C.C. pipes NP2 class 100 mm dia metre 200.00
SUB HEAD : 19.0 DRAINAGE 358

No.

1714 R.C.C. collars NP2 class 100 mm dia each 30.00
1728 RCC pipe 450 mm dia NP-3 spigot metre 1496.00
1854 Stoneware pipes grade A (60 cm long) 100 mm dia each 55.00

No.
1900 S.W. gully trap P type 100x100 mm each 100.00
2224 Carriage of S.W. pipes 100 mm dia 100 metre 138.36
2299 Carriage of R.C.C. pipes 450 & 500 mm dia 100 metre 2520.19
2303 Carriage of R.C.C. pipes 600,700,750 & 800 mm dia 100 metre 3780.28
2336 Carriage of R.C.C. pipe above 1200 mm dia and upto
1800 mm dia 100 metre 7560.57
2602 Common burnt clay F.P.S. (non modular) bricks class
designation 7.5 1000 Nos 4500.00
3860 560 mm dia cover with frame (Heavy duty) each 9000.00
3861 560 mm dia cover without frame (Heavy duty) each 5000.00
7087 S.C.I. Tee 150 mm each 570.00
7128 S.W. intercepting trap 100 mm dia each 185.00
7130 Rectangular shape 600x450 mm precast R.C.C. manhole
cover with frame - L.D. - 2.5 each 675.00
7131 Square shape 450x450 mm precast R.C.C. manhole cover
with frame - L.D. - 2.5 each 575.00

No.
7132 Circular shape 450 mm dia precast R.C.C. manhole cover

with frame - L.D. - 2.5 each 575.00
7133 Rectangular shape 500x500 mm precast R.C.C. manhole
cover with frame - M.D. - 10 each 670.00
with frame- M.D.-10 each 575.00
with frame - H.D. - 20 each 880.00
with frame - E.H.D. - 35 each 1170.00
7354 Plastic encapsulated M.S. foot rest 30x20x15 cm each 110.00
7380 Precast R.C.C. grating with frame 500x450 mm horizontal
grating each 620.00
7381 Precast R.C.C. grating with frame 450x100 mm vertical
grating each 235.00
8701 SS pipe 304 grades with press fit technology as per JIS
3448 standard 48.60 mm outer dia metre 610.00

19.0 DRAINAGE
No.
NOTE : - The rates given for all the items under sub-head ‘Drainage’
are applicable to work executed in soils above sub- soil water level.
Extra allowance has to be made for work under sub- soil water level.
STONE WARE PIPES AND FITTINGS
19.1 Providing, laying and jointing glazed stoneware pipes class SP-1
with stiff mixture of cement mortar in the proportion of 1:1 (1 cement
: 1 fine sand) including testing of joints etc. complete :
19.1.1 100 mm diameter metre 317.05
19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) all-round
S.W. pipes including bed concrete as per standard design :
19.2.1 100 mm diameter S.W. pipe metre 817.00
19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) up to
haunches of S.W. pipes including bed concrete as per standard
design :
19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete
with C.I. grating brick masonry chamber with water tight C.I. cover
with frame of 300 x300 mm size (inside) the weight of cover to be not
less than 4.50 kg and frame to be not less than 2.70 kg as per
standard design:
19.4.1 100x100 mm size P type
19.4.1.1 With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5 each 2307.00
19.4.1.2 With Sewer bricks conforming to IS : 4885 each 2311.05
19.4.2 150 x 100 mm size P type

No.
19.4.2.2 With sewer bricks conforming to IS : 4885 each 2321.45

19.4.3 180x150 mm size P type
19.5 Dismantling of old S.W. pipes including breaking of joints and bed
concrete stacking of useful materials near the site within 50 m lead
and disposal of unserviceable materials into municipal dumps :
19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C.
pipes with collars jointed with stiff mixture of cement mortar in the
proportion of 1:2 (1 cement : 2 fine sand) including testing of joints
etc. complete :
19.6.1 100 mm dia. R.C.C. pipe metre 415.75
19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement
: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement :
1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm
nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse
sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),
inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3
coarse sand) finished with floating coat of neat cement and making

No.
channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) finished with a floating
coat of neat cement complete as per standard design :
19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover
with frame (light duty) 455x610 mm internal dimensions,
total weight of cover and frame to be not less than 38 kg
(weight of cover 23 kg and weight of frame 15 kg) :
with frame (medium duty) 500 mm internal diameter, total
weight of cover and frame to be not less than 116 kg (weight
of cover 58 kg and weight of frame 58 kg) :
with frame (heavy duty) 560 mm internal diameter, total
weight of cover and frame to be not less than 208 kg (weight
of cover 108 kg and weight of frame 100 kg) :
19.8 Extra for depth for manholes :
19.8.1 Size 90x80 cm
bricks of class designation 7.5 metre 7503.00
19.8.1.2 With Sewer bricks conforming to IS : 4885 metre 7533.80
19.8.2 Size 120x90 cm
19.8.2.2 With Sewer bricks conforming to IS : 4885 metre 9031.30
19.9 Constructing brick masonry circular type manhole 0.91 m internal
dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement
: 4 coarse sand), inside cement plaster 12 mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat
of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse
sand : 6 graded stone aggregate 40 mm nominal size), and making
necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) finished
with a floating coat of neat cement, all complete as per standard
design :

No.
19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty,
HD-20 grade designation) 560 mm internal diameter con-
forming to I.S. 12592, total weight of cover and frame to be
not less than 182 kg., fixed in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) including centering, shuttering all complete.
(Excavation, foot rests and 12mm thick cement plaster at
the external surface shall be paid for separately) :
19.10 Extra depth for circular type manhole 0.91m internal dia (at bottom)
beyond 0.91 m to 1.67 m
19.10.2 With Sewer bricks conforming IS : 4885 metre 6474.15
19.11 Constructing brick masonry circular manhole 1.22 m internal dia at
bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4
coarse sand) inside cement plaster 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat
cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6
graded stone aggregate 40 mm nominal size) and making necessary
channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
coat of neat cement, all complete as per standard design :
19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-
20 grade designation) 560 mm internal diameter conform-
ing to I.S. 12592, total weight of cover and frame to be not
less than 182 kg. fixed in cement concrete 1:2:4 (1 ce-
ment : 2 coarse sand : 4 graded stone aggregate 20 mm
(Excavation, foot rests and 12 mm thick cement plaster at
19.11.1.2 With Sewer bricks conforming IS : 4885 each 21254.90
19.12 Extra depth for circular type manhole 1.22 m internal dia (at bottom)
beyond 1.68 m to 2.29 m :
19.13 Constructing brick masonry circular manhole 1.52 m internal dia at
bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4
coarse sand) inside cement plaster 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat
cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6

No.
graded stone aggregate 40 mm nominal size) and making necessary

channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
coat of neat cement, all complete as per standard design :
19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD-
20 grade designation) 560 mm internal diameter conform-
ing to I.S. 12592, total weight of cover and frame to be not
less than 182 kg. fixed in cement concrete 1:2:4 (1 ce-
ment : 2 coarse sand : 4 graded stone aggregate 20 mm
(Excavation, foot rests and 12 mm thick cement plaster at
19.13.1.2 With Sewer bricks conforming IS : 4885 each 45531.90
19.14 Extra depth for circular type manhole 1.52 m internal dia (at bottom)
beyond 2.30 m :
19.15 Providing M.S. foot rests including fixing in manholes with
20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) as per
standard design :
19.15.1 With 20x20 mm square bar each 422.20
19.15.2 With 20 mm diameter round bar each 383.70
19.16 Providing orange colour safety foot rest of minimum 6 mm thick
plastic encapsulated as per IS : 10910, on 12 mm dia steel bar
conforming to IS: 1786, having minimum cross section as 23 mmx25
mm and over all minimum length 263 mm and width as 165 mm with
minimum 112 mm space between protruded legs having 2 mm tread
on top surface by ribbing or chequering besides necessary and
adequate anchoring projections on tail length on 138 mm as per
standard drawing and suitable to with stand the bend test and
chemical resistance test as per specifications and having
manufacture’s permanent identification mark to be visible even after
fixing, including fixing in manholes with 30x20x15 cm cement
concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) complete as per design. each 463.05
19.17 Replacement of M.S. foot rests in manholes including dismantling
concrete blocks and fixing with 20x20x10 cm cement concrete blocks
nominal size):
19.17.1 With 20x20 mm square bar each 516.40
19.17.2 With 20 mm diameter round bar each 477.90

No.
19.18 Supplying and fixing C.I. cover without frame for manholes :
19.18.1 455x610 mm rectangular C.I. cover (light duty) the weight
of the cover to be not less than 23 kg each 1326.25
19.18.2 500 mm diameter C.I. cover (medium duty) the weight of the
cover to be not less than 58 kg each 3202.90
19.18.3 560 mm diameter C.I. cover (heavy duty) the weight of the
cover to be not less than 108 kg each 6822.40
19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and
frame of required shape and approved quality
19.19.1 L D- 2.5
19.19.1.1 Rectangular shape 600x450 mm internal
dimensions each 1228.90
19.19.1.2 Square shape 450 mm internal dimensions each 1027.25
19.19.1.3 Circular shape 450 mm internal diameter each 1027.25
19.19.2 M D - 10
19.19.2.1 Square shape 450 mm internal dimension each 1230.60
19.19.3 H D - 20
19.19.4 EHD - 35
19.19.4.1 Circular shape 560 mm internal dia each 1859.50
19.20 Supplying and fixing C.I. cover 300x300 mm without frame for gully
trap (standard pattern) the weight of cover to be not less than 4.5 kg each 667.80
19.21 Making connection of drain or sewer line with existing manhole
including breaking into and making good the walls, floors with cement
concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) cement plastered on both sides
with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a
floating coat of neat cement and making necessary channels for the
drain etc. complete :
19.21.1 For pipes 100 to 250 mm diameter each 623.50
19.22 Providing sand cast iron drop connection externally for 60 cm drop
from branch sewer line to main sewer manhole including inspection
and cleaning eye with chain and lid, sand cast iron drop pipe and
bend encased all-round with cement concrete 1:5:10 (1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominal size) with all
centering and shuttering required, cutting holes in walls and making
good with brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand)
on inside of the manhole wall, lead caulked joints between sand
cast iron pipes and fittings, stiff cement mortar 1:1 (1 cement : 1

No.
fine sand) joints between sand cast iron tee and S.W. pipe, making
required channels complete as per standard design and
specifications :
19.22.1 100 mm dia sand cast iron drop connection each 9334.20
19.23 Extra for depths beyond 60 cm of sand cast iron drop connection
complete:
19.23.1 For 100 mm dia sand cast iron drop connection metre 2632.40
19.23.2 For 150 mm dia sand cast iron drop connection metre 3418.90
19.24 Dismantling of manhole including R.C.C. top slab, C.I. cover with
frame, including stacking of useful materials near the site and disposal
of unserviceable materials within 50 m lead as per direction of
Engineer- charge :
19.24.1 Rectangular manhole 90x80 cm and 45 cm deep each 1815.85
19.24.2 Rectangular manhole 120x90 cm and 90 cm deep each 3196.30
19.24.3 Rectangular arch type manhole 140x90 cm and 2.45 m
deep each 6046.60
19.24.4 Circular manhole 122 cm diameter and 1.68 m deep each 4624.55
19.25 Extra for depth of manholes dismantled :
19.25.1 Rectangular manhole 90x80 cm and beyond 45 cm depth metre 1460.05
19.25.2 Rectangular manhole 120x90 cm and beyond 90 cm depth metre 1739.35
19.25.3 Rectangular arch type manhole 140x90 cm and beyond
2.45 m depth (up to 4.25 m depth) metre 1409.80
19.25.4 Circular manhole 122 cm diameter and beyond 1.68 m
depth (up to 2.29 m depth) metre 1590.55
19.26 Raising manhole cover and frame slab to required level including
dismantling existing slab and making good the damage as required
(Raising depth of manhole to be paid separately) :
19.26.1 Rectangular manhole 90x80 cm with rectangular cover
600 x 450 mm of grade LD - 2.5 each 2457.95
19.26.2 Rectangular manhole 120x90 cm with circular cover
500 mm dia of grade MD - 10 each 3871.15
19.26.3 Rectangular manhole 120x90 cm with circular cover
560 mm dia of grade HD - 20 each 3600.25
19.26.4 Circular manhole 140 cm dia with circular cover 600 mm
dia of grade EHD - 35 each 297.60
19.27 Constructing brick masonry road gully chamber 50x45x60 cm with
bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including
500x450 mm pre-cast R.C.C. horizontal grating with frame complete
as per standard design :

No.
19.28 Constructing brick masonry road gully chamber 45x45x77.5 cm with

bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast
R.C.C. vertical grating complete as per standard design :
19.29 Constructing brick masonry road gully chamber 110x50x77.5 cm
with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including
500x450 mm precast R.C.C. horizontal grating with frame and vertical
grating complete as per standard design :
19.30 Constructing brick masonry chamber for underground C.I. inspection
chamber and bends with bricks in cement mortar 1:4 (1 cement : 4
coarse sand) C.I. cover with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not less than 38
kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab
with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone
aggregate 20 mm nominal size), foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal
size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement
: 3 coarse sand), finished smooth with a floating coat of neat cement
on walls and bed concrete etc. complete as per standard design:
19.30.1 Inside dimensions 455x610 mm and 45 cm deep for single
pipe line :
19.30.2 Inside dimensions 500x700 mm and 45 cm deep for pipe
line with one or two inlets :
19.30.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe
line with three or more inlets :
19.31 Extra for depth beyond 45 cm of brick masonry chamber :
19.31.1 For 455x610 mm size
19.31.2 For 500x700 mm size
19.31.3 For 600x850 mm size

No.
19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry
brick honey comb shaft with bricks and S.W. drain pipe 100 mm
diameter, 1.8 m long complete as per standard design.
19.33 Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including
S.W. drain pipe 100 mm diameter and 1.20 m long complete as per
standard design. each 2608.00
19.34 Providing and fixing S.W. intercepting trap in manholes with stiff
mixture of cement mortar 1:1 (1 cement : 1 fine sand) including
testing of joints etc. complete :
19.34.1 100 mm dia each 365.65
19.34.2 150 mm dia each 494.75
19.35 Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C.
pipes including collars/spigot jointed with stiff mixture of cement
mortar in the proportion of 1:2 (1 cement : 2 fine sand) including
testing of joints etc. complete
19.35.1 450 mm dia RCC pipes. metre 2323.90
19.35.4 1000 mm dia RCC pipes. (Laying by manual/ machanical
means) metre 5816.30
19.35.6 1800 mm dia RCC pipes. (Laying by manual/ machenical
19.36 Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C.
pipes including collars/spigot jointed with stiff mixture of cement
mortar in the proportion of 1:2 (1 cement : 2 fine sand) including
testing of joints etc. complete
19.36.4 1000 mm dia RCC pipes.(Laying by manual/ machanical

SUB HEAD : 20.0
PILE WORK
371
BASIC RATES (SH: 20.0 PILE WORK)
No.
0015 Hire and running charges of Tripod and Mechanical Winch
machine complete with power unit and accessories day 1900.00
0024 Hire and running charges of hydraulic piling rig with power unit etc.
including complete accessories and shifting at site day 30000.00
0025 Hire and running charges of light crane day 3000.00
0026 Hire and running charges of bentonite pump day 3500.00
0027 Hire and running charges of vibrating pile driving hammer complete
with power unit and accessories day 30000.00
0028 Hire and running charges of crane 20 tonne capacity day 7000.00
0080 Hire and running charges of drill machine up to 400 mm dia
(including cost of mobile oil, diesel consumption in ordinary soil
and operator) day 7500.00
0081 Pile Integrity testing equipment day 3000.00
0161 Helper (Technician) day 558.00
7181 C.I. pile shoe kg 48.00
7182 M.S. clamps for pile shoe of 35 kg per pile kg 43.00
7183 Bentonite tonne 2960.00
7246 Vertical load testing (initial) of piles in accordance with IS : 2911
(Part-IV) including installation of loading platform and preparation
of pile head or construction of test cap and dismantling of test
cap after test etc. complete as per specification and up to 50
tonne capacity pile per test 40000.00
of pile head or construction of test cap and dismantling of
test cap after test etc. complete as per specification & above 50
tonne and up to 100 tonne per test 45000.00
of pile head or construction of test cap and dismantling of test
cap after test etc. complete as per specification & group of two
or more up to 50 tonne per test 50000.00
SUB HEAD : 20.0 PILE WORK 372

No.
7249 Cyclic vertical load testing of piles in accordance with IS : 2911

(Part-IV) including preparation of pile head etc. for Single pile up
to 50 tonne capacity per test 15000.00
(Part-IV) including preparation of pile head etc. for Single pile
above 50 tonne capacity pile and up to 100 tonne capacity pile per test 23000.00
(Part-IV) including preparation of pile head etc. for Group of two
piles up to 50 tonne capacity each per test 29500.00
7252 Lateral load testing of single pile in accordance with IS : 2911
part -IV for determining safe allowable lateral load on pile up to
50 tonne capacity per test 15000.00
7253 Lateral load testing of single pile in accordance with IS : 2911
part -IV for determining safe allowable lateral load on pile above
50 tonne capacity per test 23600.00

20.0 PILE WORK
No.
20.1 Providing, driving with hydraulic piling rigs with power units and
installing driven cast-in-situ reinforced cement concrete piles of grade
M-25 of specified diameter and length below the pile cap, to carry
safe working load not less than specified, excluding the cost of steel
reinforcement but including the cost of shoe and the length of pile to
be embedded in the pile cap etc. all complete. (Length of pile for
payment shall be measured from top of shoe to the bottom of pile
cap) :
20.1.1 400 mm dia piles metre 2244.10
20.2 Boring, providing and installation bored cast-in-situ reinforced cement
concrete piles of grade M-25 of specified diameter and length below
the pile cap, to carry a safe working load not less than specified,
excluding the cost of steel reinforcement but including the cost of
boring with bentonite solution and temporary casing of appropriate
length for setting out and removal of same and the length of the pile
to be embedded in the pile cap etc. by percussion drilling using
Direct mud circulation (DMC) or Bailer and chisel technique by tripod
and mechanical Winch Machine all complete, including removal of
excavated earth with all its lifts and leads (length of pile for payment
shall be measured up to bottom of pile cap).
Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not
be used .
20.2A Boring, providing and installation bored cast-in-situ reinforced cement
concrete piles of garde M-25 of specified diameter and length below
pile cap, to carry a safe working load not less than specified, excluding
the cost of steel reinforcement but including the cost of boring with
bentonite solution and temporary casing of appropriate length for
setting out and removal of same and the length of the pile to be
embedded in the pile cap etc. by Crawler mounted, telescopic boom
hydraulic pilling Rig all complete, including removal of excavated
earth with all its lifts and leads (length of pile for payment shall be
measured up to bottom of pile cap).

No.
Note: Truck Mounted rotary/TMR/Tube well boring machine shall not

be used.
20.2A.1 600 mm dia piles metre 4225.60
20.3 Boring with hydraulic piling rigs with power units, providing and
installing cast in situ single under reamed piles of specified diameter
and length below pile cap in M-25 cement concrete, to carry a safe
working load not less than specified, excluding the cost of steel
reinforcement but including the cost of boring with bentonite solution
and the length of the pile to be embedded in pile cap etc. all complete.
(Length of pile for payment shall be measured upto to the bottom of
pile cap) :
20.4 Extra over single under ream for providing additional bulbs in
under reamed piles, under specified diameter(only the nos. of
extra bulbs are to be paid)
20.4.1 300 mm dia piles each 1931.85
20.4.2 400 mm dia piles each 2183.65
20.4.3 450 mm dia piles each 2335.50
20.4.4 550 mm dia piles each 2558.20
20.5 Providing, driving (with vibrating pile driving hammer complete
with power units & accessories) and installing driven Pre-cast
reinforced cement concrete piles of specified diameter and length below
the pile cap in M-25 cement concrete to carry safe working load not
less than specified, with a central through preformed hole with M.S.
black pipe of dia, 40 mm for grouting with cement sand grouting of mix
1:2 (1cement : 2 coarse sand) under sufficient positive pressure to
ensure complete filling including centring, shuttering, driving and
removing the steel casing pipe and lifting casing etc. complete but
excluding the cost of steel reinforcement. (Length of pile for payment
shall be measured from top of the shoe to the bottom of pile cap).

No.
20.6 Vertical load testing of piles in accordance with IS 2911 (Part IV)
including installation of loading platform by Kentledge/Anchor piles
method and preparation of pile head or construction of test cap and
dismantling of test cap after test etc. complete as per specification
& the direction of Engineer in-charge.
Note: 1. Initial and Routine Load Test shall not be carried out by
Dynamic method of testing.
Note: 2. Testing agency shall submit the design of loading platform
for the approval of Engineer-in-charge.
20.6.1 Single pile upto 50 tonne Safe capacity
20.6.1.1 Initial test (Test Load 2.5 times the Safe
capacity) per test 53517.50
20.6.1.2 Routine test (Test Load 1.5 times the Safe
20.6.2 Single pile above 50 tonne and upto 100 tonne Safe
capacity
20.6.3 Group of two or more piles upto 50 tonne Safe capacity
20.7 Cyclic vertical load testing of pile in accordance with IS Code of
practice IS:2911 (part IV) by Kentledge method including preparation
of pile head etc for.
20.7.1 Single pile
20.7.1.1 Upto 50 tonne Safe capacity pile per test 20069.05
20.7.1.2 Above 50 tonne and upto 100 tonne Safe
capacity pile per test 30772.55
20.7.2 Group of two or more piles
20.7.2.1 Upto 400 tonne Safe capacity of group per test 39469.15
20.8 Lateral load testing of single pile in accordance with IS Code of
practice IS : 2911 (Part IV) for determining safe allowable lateral load
on pile :
20.8.1 Upto 50 tonne capacity pile per test 20069.05
20.8.2 Above 50 tonne and upto 100 tonne capacity pile per test 31575.35
20.9 Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic
Echo Test method in accordance with IS 14893 including surface
preparation of pile top by removing soil, mud, dust & chipping lean

No.
concrete lumps etc. and use of computerised equipment and high

skill trained personal for conducting the test & submission of results,
all complete as per direction of Engineer-in-charge. per test 938.90
Note :- The inclusion of the above item in the schedule of work shall
be judiciously decided by the technical sanctioning authority, keeping
in view the quality control, type of soil strata & importance of the
project.

SUB HEAD : 21.0
ALUMINIUM WORK
378
BASIC RATES (SH: 21.0 ALUMINIUM WORK)
No.
0689 Anodised Aluminium butt hinges 100x75x4 mm 10 Nos 393.00
0992 Galvanised steel plain sheets quintal 5000.00
2406 Float glass panes of nominal thickness 4 mm (weight not
less than 10 kg/sqm) sqm 300.00
2604 Weather/ structural non sag. Elastomeric PU sealant (600ml)
sausage) for joints in RCC/ Brick/ stone/ Wood/ Ceramic/ Gypsum/
Aluminum work complying to ASTM C 920, DIN 18540 - F & ISO
11600 incl. all taxes each 532.00
7001 Brass 100mm mortice latch and lock with 6 levers without pair
of handles each 210.00
7313 Expandable fastener with plastic sleeve and M.S. screws :
32 mm long each 10.00
7347 Cadmium plated full threaded steel screws (30x4 mm dia) 100 Nos 27.00
7348 Aluminium washer 2 mm thick 15 mm dia 100 Nos 10.00
7388 Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt each 11.00
7389 Anodising 15 microns on aluminium sections kg 38.00
7390 EPDM Gasket for uPVC window/door metre 19.00
7392 Powder coating 50 microns on aluminium sections kg 61.00
7393 Polyester powder coating 50 microns on aluminium sections kg 67.00
7394 Double action hydraulic floor spring with stainless steel
cover plate each 1500.00
7395 6 mm dia G.I. adjustable hangers including clips (up to 1.2 m
length) each 20.00
SUB HEAD : 21.0 ALUMIINIUM WORK 379
No.
7396 Double action hydraulic floor spring with brass cover plate each 1620.00
7477 Prelaminated particle board with one side decorative and
other side balancing lamination, flat pressed 3 layer & graded
(medium density) Grade i, Type II conforming to IS : 12823 (exterior
grade) 12 mm thick sqm 540.00
7480 Prelaminated particle board with both sides decorative lamination,
flat pressed 3 layer & graded (medium density) Grade I, Type II
conforming to IS : 12823 (exterior grade) 12 mm thick sqm 575.00
8646 Weather Silicon sealant cartridge 100.00
8647 Stainless steel screws 30 mm x4 mm 100 Nos 32.00
8648 Hermetically sealed double glazed unit made with 6 mm thick clear
float glass both side having 12 mm air gap sqm 2150.00
8649 Stainless steel (SS 304 grade) adjustable friction window stay
205 x 19 mm each 172.00
255 x 19 mm each 222.00
355 x 19 mm each 195.00
510 x 19 mm each 525.00
710 x 19 mm each 900.00
8654 Masking tape metre 1.95
8660 Aluminium casement window fastener (Anodised AC 15) each 44.00
8661 Aluminium casement window fastener (powder coated ) each 47.00
8662 Aluminium casement window fastener (polyester powder
coated) each 46.00
8663 Aluminium round shape handle (anodised AC 15) outer dia 100 mm each 53.00
8664 Aluminium round shape handle (powder coated) outer dia 100 mm each 56.00
8665 Aluminium round shape handle (polyester powder coated)
outer dia 100 mm each 60.00
8674 Precoated galvanised steel gutter 600mm overall girth metre 420.00
8676 Precoated galvanised steel barge board (upto 300mm ) metre 215.00
8678 1 mm thick 35 mm wide bright finished stainless steel piano hinges metre 42.00
8774 Aluminium Grill as per IS 1868 kg 260.00
8776 Stainless steel dash fastener of 8 mm dia and 75 mm long bolt each 15.00
8778 Toughened glass 12 mm thickness sqm 1747.00
SUB HEAD : 21.0 ALUMIINIUM WORK 380

21.0 ALUMINIUM WORK
No.
21.1 Providing and fixing aluminium work for doors, windows, ventilators
and partitions with extruded built up standard tubular sections/
appropriate Z sections and other sections of approved make
conforming to IS: 733 and IS: 1285, fixing with dash fasteners of
required dia and size, including necessary filling up the gaps at
junctions, i.e. at top, bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge. (Glazing, paneling
and dash fasteners to be paid for separately) :
21.1.1 For fixed portion
21.1.1.1 Anodised aluminium (anodised transparent
or dyed to required shade according to IS:
1868, Minimum anodic coating of grade AC
15) kg 423.95
21.1.1.2 Powder coated aluminium (minimum
thickness of powder coating 50 micron) kg 456.30
21.1.1.3 Polyester powder coated aluminium
(minimum thickness of polyester powder
coating 50 micron) kg 464.70
21.1.2 For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making provision
for fixing of fittings wherever required including the cost
of EPDM rubber / neoprene gasket required (Fittings
shall be paid for separately)
21.1.2.1 Anodised aluminium (anodised transparent
or dyed to required shade according to IS:
1868, Minimum anodic coating of grade AC
15) kg 513.40
21.1.2.2 Powder coated aluminium (minimum
21.1.2.3 Polyester powder coated aluminium
(minimum thickness of polyester powder
coating 50 micron) kg 554.95
21.2 Providing and fixing 12 mm thick prelaminated particle board flat
pressed three layer or graded wood particle board conforming to IS:
12823 Grade l Type ll, in panelling fixed in aluminum doors, windows
shutters and partition frames with C.P. brass / stainless steel screws
etc. complete as per architectural drawings and directions of engineer-
in-charge.
21.2.1 Pre-laminated particle board with decorative lamination
on one side and balancing lamination on other side sqm 997.70
21.2.2 Pre-laminated particle board with decorative lamination
on both sides sqm 1046.90
SUB HEAD : 21.0 ALUMINIUM WORK 381

No.
21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters
and partitions etc. with EPDM rubber / neoprene gasket etc. complete as
per the architectural drawings and the directions of engineer-in-charge .
(Cost of aluminium snap beading shall be paid in basic item):
21.3.1 With float glass panes of 4.0 mm thickness (weight not
less than 10 kg/ sqm) sqm 999.60
21.3.2 With float glass panes of 5 mm thickness (weight not
less than 12.50 kg/ sqm) sqm 1296.40
21.3.3 With float glass panes of 8 mm thickness (weight not
less than 20 kg/ sqm) sqm 1462.35
21.4 Providing and fixing double action hydraulic floor spring of approved brand
and manufacture conforming to IS : 6315, having brand logo embossed
on the body / plate with double spring mechanism and door weight upto
125 kg, for doors, including cost of cutting floors, embedding in floors as
required and making good the same matching to the existing floor finishing
and cover plates with brass pivot and single piece M.S. sheet outer box
with slide plate etc. complete as per the direction of Engineer-in-charge.
21.4.1 With stainless steel cover plate minimum 1.25 mm
thickness each 2412.50
21.4.2 With brass cover plate minimum 1.25 mm thickness each 2573.05
21.5 Providing and fixing powder coated aluminium work (minimum
thickness of powder coating 50 micron) consisting of tee/ angle
sections, of approved make conforming to IS : 733 in frames of false
ceiling including aluminium angle cleats with necessary C.P. brass/
stainless steel sunk screws, aluminium perimeter angles fixed to
wall with stainless steel rawl plugs @ 450 mm centre to centre and
fixing the frame work to G.I. level adjusting hangers 6 mm dia. with
necessary cadmium plated machine screws all complete as per
approved architectural drawings and direction of the Engineer-in-
charge (level adjusting hangers, ceiling cleats and expansion hold
fasteners to be paid for separately). kg 670.85
21.6 Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto
1200mm length), fixed to roof slabs by means of ceiling cleats made
out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable
dash fastener of 12.5 mm dia and 50 mm long, complete as per
21.7 Providing and fixing machine moulded aluminium covering of approved
pattern & design, made out of machine cut aluminium sheet and
machine holed for receiving dash fastener, over expansion joints on
vertical surfaces/ceiling floors, the fixing on plate in one row on one
side of joint only shall be done with stainless steel dash fasteners of
8 mm dia and 75 mm long bolt including providing aluminium washers
2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to
centre including drilling holes in the receiving surface and providing
expandable plastic sleeves in holes etc. complete as per direction of
Engineer-in-charge.

No.
21.7.1 Anodised aluminium sheet 2.5mm thick (anodised trans-

parent or dyed to required shade according to IS: 1868,
Minimum anodic coating of grade AC 15) kg 582.05
21.7.2 Powder coated aluminium sheet 2.5mm thick (minimum
21.8 Filling the gap in between aluminium frame & adjacent RCC/ Brick/
Stone work by providing weather silicon sealant over backer rod of
approved quality as per architectural drawings and direction of
Engineer-in-charge complete.
21.8.1 Upto 5mm depth and 5 mm width metre 79.45
21.9 Extra for applying additional anodic coating AC 25 instead of AC 15
to aluminium extruded sections.
21.9.1 For fixed portion kg 13.40
21.9.2 For shutters of doors, windows & ventilators kg 13.40
21.10 Providing and fixing double glazed hermetically sealed glazing in
aluminium windows, ventilators and partition etc. with 6 mm thick
clear float glass both side, having 12 mm air gap, including providing
EPDM gasket, perforated aluminium spacers, desiccants, sealant
(Both primary and secondary sealant) etc. as per specifications,
drawings and direction of Engineer-in-charge complete. sqm 3905.35
21.11 Providing and fixing stainless steel (SS 304 grade) adjustable friction
windows stays of approved quality with necessary stainless steel
screws etc. to the side hung windows as per direction of Engineer-
in-charge complete.
21.11.1 205 X 19 mm each 255.75
21.11.2 255 X 19 mm each 322.65
21.11.3 355 X 19 mm each 286.50
21.11.4 510 X 19 mm each 728.05
21.11.5 710 X 19 mm each 1229.75
21.12 Providing and fixing aluminium tubular handle bar 32 mm outer dia,
3.0 mm thick & 2100 mm long with SS screws etc .complete as per
direction of Engineer-in-Charge.
21.12.1 Anodized (AC 15 ) aluminium tubular handle bar each 512.30
21.12.2 Powder coated minimum thickness 50 micron aluminium
tubular handle bar each 562.60
21.12.3 Polyester powder coated minimum thickness 50 micron
aluminium tubular handle bar each 575.70
21.13 Providing and fixing Brass 100mm mortice latch and lock with 6
levers without pair of handles (best make of approved quality) for
aluminium doors including necessary cutting and making good etc.
21.14 Providing and fixing anodised aluminium (anodised transparent or
dyed to required shade according to IS: 1868. Minimum anodic
coating of grade AC 15) sub frame work for windows and ventilators

No.
with extruded built up standard tubular sections of approved make

conforming to IS: 733 and IS: 1285, fixed with dash fastener of required
dia and size (Dash fastener to be paid for separately). kg 354.75
21.15 Providing and fixing aluminium casement windows fastener of required
length for aluminium windows with necessary screws etc. complete.
21.15.1 Anodized (AC 15) aluminium each 67.55
21.15.2 Powder coated minimum thickness 50 micron aluminium each 71.55
aluminium each 70.25
21.16 Providing and fixing aluminium round shape handle of outer dia 100
mm with SS screws etc. complete as per direction of Engineer-in-
charge
21.16.1 Anodized (AC 15 ) aluminium each 79.60
21.16.2 Powder coated minimum thickness 50 micron aluminium each 83.60
aluminium each 88.95
21.17 Providing and fixing anodised aluminium grill (anodised transparent
or dyed to required shade according to IS: 1868 with minimum anodic
coating of grade AC 15) of approved design/pattern, with approved
standard section and fixed to the existing window frame with C.P.
brass/ stainless steel screws @ 200 mm centre to centre, including
cutting the grill to proper opening size for fixing and operation of
handles and fixing approved anodised aluminium standard section
around the opening, all complete as per requirement and direction of
Engineer-in-charge. (Only weight of grill to be measured for payment). kg 519.85
21.18 Providing and fixing 12 mm thick frameless toughened glass door
shutter of approved brand and manufacture, including providing and
fixing top & bottom pivot & double action hydraulic floor spring
type fixing arrangement and making necessary holes etc. for fixing
required door fittings, all complete as per direction of Engineer-in-
charge (Door handle, lock and stopper etc.to be paid separately). sqm 4447.90
21.19 Filling the gap in between aluminium/ stone/ wood frame and adjacent
RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing
weather/structural non sag elastomeric PU sealant over backer rod
of approved quality as per architectural drawings and direction of
Engineer-in-charge complete, complying to ASTM C920, DIN 18540-
F & ISO 11600
21.19.1 Upto 5 mm depth and 5 mm width metre 125.10

SUB HEAD : 22.0
WATER PROOFING
385
BASIC RATES (SH : 22.0 WATER PROOFING)
No.
0128 Mate day 617.00
0318 Bitumen felt fibre base (vegetable or animal):As per IS 7193 Grade I sqm 70.00
0319 Bitumen felt as per IS 7193 Grade II sqm 80.00
0322 Bitumen felt :Type 3 grade 1 sqm 70.00
0351 Integral crystalline slurry kg 238.00
0352 Integral crystalline admixture kg 272.00
0353 Crystalline mortar kg 215.00
0354 Integral crystalline dry shake kg 360.00
0355 Swellable type water stop tape metre 365.00
0356 Primer for swellable type water stop tape litre 1540.00
1169 Kota stone slab 25mm thick (rough chiseled) sqm 301.00
1177 Stone grit 6 mm and down size or pea sized gravel cum 800.00
SUB HEAD : 22.0 WATER PROOFING 386

No.
2216 Carriage of Stone blocks white & red sand stone & kota stone
slab tonne 92.24
3002 Polyvinyl chloride sheet 400 micron thick sqm 40.00
7233 Fibre glass tissue reinforcement Type II Grade i sqm 82.00
7427 Water stops Serrated with central bulb (225 mm wide, 8-11 mm
thick) metre 200.00
7428 Water stops Dumb bell with central bulb metre 160.00
7429 Kickers metre 185.00
8200 A.P.P. modified polymeric felt (two layers) 1.5 mm thick sqm 80.00
8201 A.P.P. modified polymeric felt (two layers) 2 mm thick sqm 100.00
8203 A.P.P. modified 2 mm thick membrane reinforced with glass
fibre matt sqm 126.67
8204 A.P.P. modified 3 mm thick membrane reinforced with glass
fibre matt sqm 190.00
8205 A.P.P. modified 3 mm thick membrane reinforced with polye
ster matt sqm 205.00
8501 Polymer modified cementation coating kg 140.00
8502 Fibre glass cloth sqm 25.00
8511 Fibre reinforced elastomeric liquid water proofing membrane litre 198.69
8512 Cementitious water proofing coating with elastic polymers kg 189.13
8513 Acrylic modified resin based texture kg 36.00

22.0 WATER PROOFING
No.
22.1 Providing and laying integral cement based treatment for water
proofing on horizontal surface at all depth below ground level for
under ground structures as directed by Engineer-in-Charge and
consisting of :
(i) Ist layer of 22 mm to 25 mm thick approved and specified rough
stone slab over a 25 mm thick base of cement mortar 1:3 (1
cement : 3 coarse sand) mixed with water proofing compound
conforming to IS:2645 in the recommended proportion over the
leveling course (leveling course to be paid separately). Joints
sealed and grouted with cement slurry mixed with water proofing
compound.
(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse
sand) mixed with water proofing compound in recommended
proportions.
(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal
size spreading @ 8 cudm/sqm thoroughly embedded in the
2nd layer.
22.1.1 Using rough kota stone. sqm 1353.70
22.2 Providing and laying integral cement based treatment for water
proofing on the vertical surface by fixing specified stone slab 22 mm
to 25 mm thick with cement slurry mixed with water proofing
compound conforming to IS:2645 in recommended proportions with
a gap of 20 mm (minimum) between stone slabs and the receiving
surfaces and filling the gaps with neat cement slurry mixed with
water proofing compound and finishing the exterior of stone slab with
cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with
neat cement punning mixed with water proofing compound in
recommended proportion complete at all levels and as directed by
22.2.1 Using rough Kota stone sqm 1738.00
22.3 Providing and laying water proofing treatment to vertical and horizontal
surfaces of depressed portions of W.C., kitchen and the like consisting
of:
(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with
water proofing compound conforming to IS 2645 in recommended
proportions including rounding off junction of vertical and
horizontal surface.
(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse
sand) mixed with water proofing compound in recommended
proportion including rounding off junction of vertical and horizontal
surface.
(iii) IIIrd course of applying blown or residual bitumen applied hot at
1.7 kg. per sqm of area.
(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints
of PVC sheet should be 100 mm wide and pasted to each other
with bitumen @ 1.7 kg/sqm). sqm 705.70

No.
22.4 Providing and Placing in position suitable PVC water stops conforming
to IS:12200 for construction/ expansion joints between two RCC
members and fixed to the reinforcement with binding wire before
pouring concrete etc. complete :
22.4.1 Serrated with central bulb (225 mm wide, 8-11 mm thick) metre 283.20
22.4.2 Dumb bell with central bulb (180 mm wide, 8 mm thick) metre 229.70
22.4.3 Kickers (320 mm wide, 5 mm thick) metre 263.15
22.5 Providing and laying water proofing treatment in sunken portion of
WCs, bathroom etc., by applying cement slurry mixed with water
proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with
water proofing cement compound @ 0.253 kg/ sqm. This layer
will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with
water proofing cement compound @ 0.126 kg/sqm. This layer
will be allowed to air cure for 4 hours followed with water curing
for 48 hours.
(The rate includes preparation of surface, treatment and sealing of
all joints, corners, junctions of pipes and masonry with polymer mixed
slurry.) sqm 465.60
22.6 Providing and laying water proofing treatment on roofs of slabs by
applying cement slurry mixed with water proofing cement compound
consisting of applying:
(a) after surface preparation, first layer of slurry of cement @ 0.488
kg/sqm mixed with water proofing cement compound @ 0.253
kg/sqm.
(b) laying second layer of Fibre glass cloth when the first layer is
still green. Overlaps of joints of fibre cloth should not be less
than 10 cm.
(c) third layer of 1.5 mm thickness consisting of slurry of cement
@ 1.289 kg/sqm mixed with water proofing cement compound
@ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will
be allowed to air cure for 4 hours followed by water curing for 48
hours. The entire treatment will be taken upto 30 cm on parapet
wall and tucked into groove in parapet all around.
(d) fourth and final layer of brick tiling with cement mortar (which
will be paid for separately.
(For the purpose of measurement the entire treated surface will be
measured.) sqm 523.05
22.7 Providing and laying integral cement based water proofing treatment
including preparation of surface as required for treatment of roofs,
balconies, terraces etc consisting of following operations:
(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of
cement admixed with water proofing compound conforming to
IS. 2645 and approved by Engineer-in-charge over the RCC

No.
slab including adjoining walls upto 300 mm height including

cleaning the surface before treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25
mm to 115 mm size with 50% of cement mortar 1:5 (1 cement
: 5 coarse sand) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge
over 20 mm thick layer of cement mortar of mix 1:5 (1 cement
:5 coarse sand ) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge to
required slope and treating similarly the adjoining walls upto
300 mm height including rounding of junctions of walls and
slabs.
(c) After two days of proper curing applying a second coat of cement
slurry using 2.75 kg/ sqm of cement admixed with water proofing
compound conforming to IS : 2645 and approved by Engineer-
in-charge.
(d) Finishing the surface with 20 mm thick jointless cement mortar
of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing
compound conforming to IS : 2645 and approved by Engineer-
in-charge including laying glass fibre cloth of approved quality
in top layer of plaster and finally finishing the surface with trowel
with neat cement slurry and making pattern of 300x300 mm
square 3 mm deep.
(e) The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test.“All
above operations to be done in order and as directed and
specified by the Engineer-in-Charge :
22.7.1 With average thickness of 120 mm and minimum
thickness at khurra as 65 mm. sqm 1398.50
22.8 Providing and laying four courses water proofing treatment with bitumen
felt over roofs consisting of first and third courses of blown bitumen
85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per
square metre of area for each course, second course of roofing felt
type 3 grade-I (hessian based self finished bitumen felt) and fourth
and final course of stone grit 6 mm and down size or pea sized
gravel spread at 6 cubic decimeter per square metre, including
preparation of surface but excluding grading complete with :
22.8.1 Bitumen felt (hessian base) type 3 grade I conforming
to IS : 1322 sqm 411.00
22.9 Providing and laying six courses water proofing treatment with
bitumen felt over roofs consisting of first, third and fifth course of
blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @
1.45, 1.20 and 1.45 Kg per square metre of area respectively, second
and fourth courses of roofing felt type 3 grade I conforming to IS :
1322 (Hessian based self finished bitumen felt) , sixth and final course
of stone grit 6 mm and down size or pea sized gravel spread at 6
cubic decimeter per sqm including preparation of surface but excluding
grading, complete. sqm 644.25

No.
bitumen felt over roofs consisting of first, third and fifth courses of
blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg
per square metre of area respectively, second and fourth courses of
roofing felt type 2 grade I (fibre base self finished bitumen felt) six
and final courses of stone grit 6 mm and down size or pea sized
gravel spread at 6 cubic decimeter per sqm including preparation of
surface, excluding grading, compete. sqm 734.25
bitumen felt over roofs consisting of first, third and fifth courses of
blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg
per square metre of area respectively, second and fourth courses of
roofing felt type 2 grade II (glass fibre base self finished bitumen felt)
and sixth and final course of stone grit 6 mm and down size or pea
sized gravel spread at 6 cubic decimeter per sqm including preparation
of surface but excluding grading, complete. sqm 734.50
22.12 Supplying and applying bituminous solution primer on roof and / or
wall surface at 0.24 litre per sqm. sqm 46.60
22.13 Deduct for omitting in water proofing treatment final course of
spreading stone grit 6 mm down size or pea sized gravel :
22.13.1 at 6 cudm per sqm sqm 14.85
22.13.2 at 8 cudm per sqm sqm 18.70
22.14 Grading roof for water proofing treatment with
22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 20mm nominal size) cum 6924.65
22.14.2 Cement mortar 1:3 (1 cement : 3 coarse sand) cum 12859.50
22.14.3 Cement mortar 1:4 (1cement : 4 coarse sand) cum 11981.80
22.22 Providing and mixing integral crystalline admixture for water proofing
treatment to RCC structures like basement raft, retaining walls,
reservior, sewage & water treatment plant, tunnels / subway and
bridge deck etc. at the time of transporting of concrete into the drum
of the ready-mix truck, using integral crystalline admixture @ 0.80%
(minimum) to the weight of cement content per cubic meter of
concrete) or higher as recommended by the manufacturer’s
specification in reinforced cement concrete at site of work. The
material shall meet the requirements as specified in ACI-212-3R-
2010 i.e. by reducing permeability of concrete by more than 90%,
compared with control concrete as per DIN 1048 and resistant to 16

No.
bar hydrostatic pressure. The crystalline admixture shall be capable

of self-healing of cracks up to a width of 0.50mm. The work shall be
carried out all complete as per specification and the direction of the
Engineer-in-charge. The product performance shall carry guarantee
for 10 years against any leakage. kg 387.20
22.22A Providing and applying fibre reinforced elastomeric liquid water
proofing membrane with resilient acrylic polymers having Sun
Reflectivity Index (SRI) of 105 on top of concrete roof in three coats
@10.76 litre/ 10 sqm. One coat of self-priming of elastomeric
waterproofing liquid (dilution with water in the ratio of 3:1) and two
coats of undiluted elastomeric waterproofing liquid (dry film thickness
of complete application/system not less than 500 microns). The
operation shall be carried out after scrapping and properly cleaning
the surface to remove loose particles with wire brushes, complete in
all respect as per the direction of Engineer-in-Charge. sqm 415.65
22.23 Providing and applying integral crystalline slurry of hydrophilic in
nature for waterproofing treatment to the RCC structures like retaining
walls of the basement, water tanks, roof slabs, podiums, reservior,
sewage & water treatment plant, tunnels / subway and bridge deck
etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline
slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral
crystalline slurry : 1 part water) for horizontal surfaces and applying
the same from negative (internal) side with the help of synthetic fiber
brush. The material shall meet the requirements as specified in ACI-
212-3R-2010 i.e by reducing permeability of concrete by more than
90% compared with control concrete as per DIN 1048 and resistant
to 16 bar hydrostatic pressure on negative side. The crystalline slurry
shall be capable of self-healing of cracks up to a width of 0.50mm.
The work shall be carried out all complete as per specification and
the direction of the engineer-in-charge. The product performance shall
carry guarantee for 10 years against any leakage.
22.23.1 For vertical surface two coats @ 0.70 kg per sqm sqm 484.45
22.23.2 For horizontal surface one coat @1.10 kg per sqm. sqm 373.40
22.23A Providing & Applying polymer modified, flexible cementatious negative
side waterproofing coating with elastic waterproofing polymers on
interior wall plaster surface in three coats @14.35 kg /10 sqm. one
coat of self priming of cementatious waterproofing polymer(dilution
with water in the ratio of 1:1) and two coats of cementatious
waterproofing polymer (dilution with water in the ratio of 3:1 ) after
scrapping and properly cleaning the surface to remove pre-existing
paint film & loose particles till plaster is visible, complete in all respect
as per the direction of Engineer-in-Charge. sqm 444.80
22.24 Providing and applying integral crystalline (dry shake) of hydrophilic
in nature for waterproofing treatment to the RCC structures like
basement raft, foundation slab, sewage & water treatment plant slab,
warehouses floor, parking structures and water tank base slab etc.
sprinkled @0.60kg per sqm or higher as recommended by the
manufacturer’s specification over the lean concrete of above cited
structures. The material shall meet the requirements as specified in
ACI-212-3R-2010 i.e. by reducing permeability of concrete by more

No.
than 85%, compared control concrete as per DIN 1048 and resistant
to 16 bar hydrostatic pressure on negative side. The crystalline dry-
shake shall be capable of self-healing of cracks up to a width of
0.50mm. The work shall be carried out all complete as per
specification and the direction of the Engineer-in-charge. The product
performance shall carry guarantee for 10 years against any leakage. sqm 327.65
22.24A Providing & Applying high quality acrylic modified resin based texture
of Dholpur/Red sand stone Pattern with anti algae and UV resistance
properties to be applied as intermediate finish in desired pattern @
43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping
and properly cleaning the surface to remove loose particles from the
plaster surface, followed by top coating with Premium Acrylic Smooth
exterior paint with Silicone additives of required shade by two
or more coats @ 1.43 litres/10 sqm, complete as the direction of
Engineer -in-Charge. sqm 424.25
22.25 Providing and applying crystalline mortar by mixing in the ratio of 4.5
: 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of
faulty construction joints, cracks, tie rod holes and spalled &
honeycombed surface of RCC underground structures like basement,
water tanks, bridge deck etc. to ensure water tightness. The crystallie
mortar shall conform to the EN 1504-3 having compressive strength
Class R4 > 45 MPa and adhesive bond strength Class R3 > 1.5
MPa. The work shall be carried out all complete as per specification
and the direction of the Engineer-In-Charge. The product performance
shall carry guarantee for 10 years against any leakage.
22.25.1 For sealing cracks and faulty construction joints, routed
out/making U-shape groove size 25x25mm and then
primed the area with integral crystalline slurry @0.05kg/
running metre and while the surface is tacky filled the
groove upto surface with crystalline mortar @1.50kg/
running metre. Once crystalline mortar is touch dry then
finally applied two coats of integral crystalline slurry
@0.05kg/running metre per coat. metre 525.70
22.25.2 For patching of tie rod holes, prepared tie rod hole surface
and then primed the area with integral crystalline slurry
@0.070kg/sqm and while the surface is tacky repair and
then filled the tie rod holes with crystalline
[email protected] per hole. The crystalline mortar should
be tightly rodded into tie rod holes or packed tightly (For
25x25x25 mm tie rod hole, use 0.040kg to fill the hole) each hole 20.75
22.26 Providing and applying of swellable type water stop tape, 19mm x
25mm thick in linear meter (expansive nature) for construction joints
treatment of RCC structure such as raft slab, retaining walls, water
storage tank and at the junctions of raft slab with the retaining walls
etc.. After cleaning the surface, one coat of required primer for
swellable water stop tape shall be applied throughout the length of
the joint @3.78 litre per 240 running meter. Over the primed surface
swellable type water stop tape shall be placed. The work shall be
carried out all complete as per specification and the direction of the
Engineer-In-Charge. The product performance shall carry guarantee
for 10 years against any leakage. metre 552.20

SUB HEAD : 23.0
RAIN WATER HARVESTING &

TUBEWELLS
394
BASIC RATES (SH: 23.0 RAIN WATER HARVESTING & TUBEWELLS)
No.
0005 Hire charges of Diesel Truck - 9 tonne day 2000.00
0020 Hydraulic Excavator (3D) with driver and fuel day 7000.00
0040 Air compressor 250 cfm with two leads for pneumatic cutters /
hammers day 1600.00
0134 Rock Hole Driller day 558.00
2319 Carriage of spun iron S & S pipes 100 mm dia 100 metre 226.82
7743 M.S. pipe 150 mm dia casing pipe metre 1126.00
7745 PVC blind pipe 150 mm dia as per IS: 12818 metre 508.62
7747 M.S. cap 150 mm dia each 150.00
7748 M.S. cap 200 mm dia each 200.00
7749 M.S bail plug 150 mm dia each 200.00
7754 Gravel 5 mm to 10 mm cum 850.00
7755 Gravel 1.5 mm to 2 mm cum 850.00
SUB HEAD : 23.0 RAIN WATER HARVESTING & TUBEWELLS

395
No.
7758 uPVC blind pipe 100 mm dia as per IS: 12818 metre 442.00
7759 uPVC slotted pipe 100 mm dia as per IS: 12818 metre 480.00
7760 M.S. cap 100 mm dia each 135.00
7761 M.S. bail plug 100 mm dia each 160.00
7762 Precast R.C.C. perforated slab each 875.00
7763 Water supply tanker of 5000 litre capacity each 900.00
7764 M.S. socket 100 mm dia each 125.00
7772 Pea Gravel cum 950.00

396
23.0 RAIN WATER HARVESTING & TUBEWELLS
No.
23.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by
suitable method prescribed in IS: 2800 (part I), including collecting
samples from different strata, preparing and submitting strata chart/
bore log, including hire & running charges of all equipments, tools,
plants & machineries required for the job, all complete as per direction
of Engineer-in-charge, upto 90 metre depth below ground level.
23.1.1 All types of soil
23.1.1.1 300 mm dia metre 512.30
23.1.1.2 350 mm dia metre 560.30
23.1.1.3 400 mm dia metre 717.20
23.1.2 Rocky strata including Boulders
23.1.2.1 300 mm dia metre 1223.20
23.1.2.2 350 mm dia metre 1293.80
23.1.2.3 400 mm dia metre 1538.95
23.2 Boring/drilling bore well of required dia for casing/ strainer pipe, by
suitable method prescribed in IS: 2800 (part I), including collecting
samples from different strata, preparing and submitting strata chart/
bore log, including hire & running charges of all equipments, tools,
plants & machineries required for the job, all complete as per direction
of Engineer -in-charge, beyond 90 metre & upto 150 metre depth
below ground level.
23.2.1 All types of soil
23.2.1.1 300 mm dia metre 597.65
23.2.1.2 350 mm dia metre 664.05
23.2.1.3 400 mm dia metre 896.50
23.2.2 Rocky strata including Boulders
23.2.2.1 300 mm dia metre 1349.95
23.2.2.2 350 mm dia metre 1411.75
23.2.2.3 400 mm dia metre 1808.50
23.3 Supplying, assembling, lowering and fixing in vertical position in bore
well, unplasticized PVC medium well casing (CM) pipe of required
dia, conforming to IS: 12818, including required hire and labour
charges, fittings & accessories etc. all complete, for all depths, as
per direction of Engineer -in-charge.
23.3.1 100 mm nominal size dia metre 600.35

397
No.

well unplasticized PVC medium well screen (RMS) pipes with ribs,
conforming to IS: 12818, including hire & labour charges, fittings &
accessories etc. all complete, for all depths, as per direction of
Engineer-in-charge.
23.5 Supplying, filling, spreading & leveling stone boulders of size range
5 cm to 20 cm, in recharge pit, in the required thickness, for all leads
& lifts, all complete as per direction of Engineer-in-charge. cum 1326.55
23.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to
10 mm, in the recharge pit, over the existing layer of boulders, in
required thickness, for all leads & lifts, all complete as per direction
of Engineer-in-charge. cum 1326.55
23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5
mm to 2 mm in recharge pit, in required thickness over gravel layer,
for all leads & lifts, all complete as per direction of Engineer -in-
charge. cum 1326.55
23.8 Gravel packing in tubewell construction in accordance with IS: 4097,
including providing gravel fine/ medium/ coarse, in required grading
& sizes as per actual requirement, all complete as per direction of
Engineer-in-charge. cum 1497.70
23.9 Providing and fixing factory made precast RCC perforated drain covers,
having concrete of strength not less than M-25, of size 1000 x 450x50
mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross
sectional T.M.T. hoop bars, including providing 50 mm dia perforations
@ 100 to 125 mm c/c, including providing edge binding with M.S.
flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-
in-charge. each 1210.85
well, ERW (Electric Resistance Welded) FE 410 mild steel screwed
and socketed/plain ended casing pipes of required dia, conforming
to IS: 4270, of reputed & approved make, including painted with
outside surface with two coats of anticorrosive paint of approved
brand and manufacture, including required hire & labour charges,
fittings & accessories, all complete, for all depths, as per direction
of Engineer-in-charge.
23.10.1 100 mm nominal size dia having minimum wall thickness
5.00 mm metre 1187.95
5.00 mm metre 1661.85
5.40 mm metre 2062.05

398
No.

well, ERW (Electric Resistance Welded) FE 410 plain slotted (having
slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain
bevel ended pipe (type A) of required dia, conforming to IS: 8110, of
reputed and approved make, having wall thickness not less than
5.40 mm, including painted with outside surface with two coats of
anticorrosive bitumestic paint of approved brand and manufacture,
including hire & labour charges, fittings & accessories, all complete,
for all depths, as per direction of Engineer -in-charge.
23.12 Development of tube well in accordance with IS : 2800 (part I) and IS:
11189, to establish maximum rate of usable water yield without sand
content (beyond permissible limit), with required capacity air
compressor, running the compressor for required time till well is fully
developed, measuring yield of well by “V” notch method or any other
approved method, measuring static level & draw down etc. by step
draw down method, collecting water samples & getting tested in
approved laboratory, i/c disinfection of tubewell, all complete, including
hire & labour charges of air compressor, tools & accessories etc.,
all as per requirement and direction of Engineer-in-charge. hour 857.60
23.13 Providing and fixing suitable size threaded mild steel cap or spot
welded plate to the top of bore well housing/ casing pipe, removable
as per requirement, all complete for borewell of:
23.13.1 100 mm dia each 189.65
23.13.2 150 mm dia each 210.75
23.13.3 200 mm dia each 280.95
23.14 Providing and fixing M.S. clamp of required dia to the top of casing/
housing pipe of tubewell as per IS: 2800 (part I), including necessary
bolts & nuts of required size complete.
23.14.1 100 mm clamp each 1409.30
23.14.2 150 mm clamp each 1489.80
23.14.3 200 mm clamp each 1691.15
23.15 Providing and fixing Bail plug/ Bottom plug of required dia to the
bottom of pipe assembly of tubewell as per IS:2800 (part I).
23.15.1 100 mm dia each 227.45
23.15.2 150 mm dia each 280.95
23.15.3 200 mm dia each 307.75

399
SUB HEAD : 24.0
CONSERVATION
OF
HERITAGE BUILDINGS
400
BASIC RATES (SH: 24.0 CONSERVATION OF HERITAGE BUILDINGS)
No.
0128 Mate day 617.00
1182 Surkhi cum 700.00
7767 Stone cleaning chemical approved by ASI litre 295.00
7768 Water repallent chemical approved by ASI litre 1200.00
7769 Stone surface strengthening chemical approved by ASI litre 900.00
7770 Turpentine oil litre 55.00
7771 Liquid Ammonia 5% litre 160.00
7775 Sodium pentachlorophenate kg 550.00
SUB HEAD : 24.0 CONSERVATION OF HERITAGE BUILDINGS

401
24.0 CONSERVATION OF HERITAGE BUILDINGS
No.
24.1 Raking out joints of stone masonry surface to the required width and
depth, with due care and precaution, by mechanical / manual means,
including preparing and cleaning the surface for re-pointing/ refilling
of joints, including disposal of rubbish to the dumping ground within
50 metre lead. sqm 51.70
24.2 Providing and fixing double scaffolding system (cup lock type) on
the exterior side of building/structure, upto 25 metre height, above
ground level, including additional rows of scaffolding in stepped manner
as per requirement of site, made with 40mm dia M.S. tube, placed
1.5 metre centre to centre, horizontal & vertical tubes joint with cup
& lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and
staircase system in the scaffolding for working platform etc. and
maintaining it in a serviceable condition for execution of work of
cleaning and/ or pointing and/ or applying chemical and removing it
thereafter. The scaffolding system shall be stiffened with bracings,
runners, connecting with the building etc, wherever required, if feasible,
for inspection of work at required locations with essential safety
features for the workmen etc., complete as per directions and approval
of Engineer-in-charge.
Note:- (1) The elevational area of the scaffolding shall be measured
for payment purpose. (2) The payment will be made once only for
execution of all items for such works. sqm 257.95
24.3 Cleaning the sand stone surface and removing dirt, dust, bird dropping,
grease, oil, algae, fungus, monkey beats, vegetable growth etc.,
including providing, applying and washing the surface with liquid
Ammonia Chemical of 5% solution and other chemical cleaning agent
as approved by Archaeological Survey of India/ Engineer-in-charge,
of approved brand and manufacturer, with the help of required
scrubbers and also cleaning with machine operated water jet mixed
with desired quantity of fine silica where ever required, without causing
any scratching/ damage to the stone surface and finally washing the
surface with clean water with the help of pressure jet machine,
complete in all respect, including taking all precautions to safeguard
ventilators, windows, doors etc. by suitable covering so as to avoid
any damage to the building/structure, all as per direction of Engineer-
in-charge (The rate is inclusive of all materials & labours involved
except scaffolding). sqm 158.15
24.4 Providing and applying antifungal wash treatment using 3% solution
of sodium pentachlorophenate, of reputed brand and manufacturer,
on cleaned sand stone surface at desired locations as per direction
of Engineer-in-charge (The rate is inclusive of all materials & labours
involved except scaffolding). sqm 59.05
24.5 Ruled / Flush pointing on Red sand stone masonry surface with
lime, surkhi and marble dust mortar in the ratio of 1:1.5:1/2 {One
lime: 1.5 surkhi (50% red and 50% light yellow surkhi ) : 1/2 marble
dust}. (The rate is inclusive of all materials & labours involved except
scaffolding). sqm 276.10
SUBHEAD : 24.0 CONSERVATION OF HERITAGE BUILDINGS

402
No.
24.6 Ruled/ Flush pointing on White sand stone masonry surface with
lime, surkhi and marble dust mortar in the ratio of 1:1.5:1/2 {One
lime : 1.5 surkhi (15% dark red and 85% light yellow surkhi) : 1/2
marble dust}. (The rate is inclusive of all materials & labours involved
except scaffolding). sqm 276.10
24.7 Applying two or more coat of Ethyl Silicate chemical as approved by
Archaeological Survey of India/ Engineer-in-charge, of approved brand
and manufacturer, with brush or spray on the existing stone masonry
surface till there is no further absorption of chemical by stone surface,
including protecting the applied surface from direct sunlight by suitable
means during application, all complete as per direction of the
Engineer-in-Charge (The rate is inclusive of all materials & labours
24.8 Applying breathable, non-reactive, antifungal, and water repellant
Silane/Siloxane chemical as approved by Archaeological Survey of
India/ Engineer-in-charge, of approved brand and manufacture, diluted
with solvent mineral Turpentine oil in the ratio of 1:12 (One part of
approved chemical :12 Part of Turpentine oil), on the existing sand
stone masonry surface with two or more coats to give uniform
application of chemical on the surface, all complete as per direction
of Engineer-In-charge (The rate is inclusive of all materials & labours
SUBHEAD : 24.0 CONSERVATION OF HERITAGE BUILDINGS

403
SUB HEAD : 25.0
STRUCTURAL GLAZING
ALUMINIUM COMPOSITE PANEL
404
BASIC RATES (SH: 25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
No.
2415 21 mm thick clear toughened laminated glass for fins with holes sqm 6000.00
2605 Structural sealant - 6 mm x 12 mm metre 30.00
2606 Spacer tape 6.4 mm thick x 6 mm wide metre 20.00
2607 Weather Sealant - Non Staining (600 ml) each 325.00
2608 Weather Sealant - Normal (300 ml) each 98.00
2609 MS Brackets/Aluminium Alloy Brackets kg 100.00
2610 Silicon Gasket in Kg (Above 50 g / m) kg 465.00
2611 EPDM Gasket in Kg (Above 60 g / m) kg 150.00
2612 Anchor Fastner - M10 each 10.00
2613 SS Bolt with washer of different sizes for structural glazing /
ACP Cladding each 35.00
2614 SS Screws of sizes for structural glazing / ACP Cladding each 3.00
2615 Protective Tape metre 20.00
2616 GI flashing - 1.2 mm Thick kg 59.00
2617 6 mm thick High performance glass sqm 1000.00
2618 6 mm thick clear heat strengthened glass sqm 650.00
2619 6 mm thick clear heat strengthened glass each 128.00
2620 ARMS GS HD - Top Hung -20"- Type P- Couple pair 1350.00
2621 Connection Block for vision glass panel each 35.00
2622 Curtain wall striker for vision glass panel each 85.00
2623 Adjustable Fastening Pawl for vision glass panel each 35.00
2624 Corner drive for vision glass panel each 255.00
2625 Top wedge Block for vision glass panel each 120.00
2626 Glass wool of denisity @ 48 Kg / cum with black glass
tissue (BGT) sqm 250.00
2627 SS Screws - # 8 x 19 each 6.00
2628 Weather Sealant - DC 789 cartridge 120.00
2629 Cement Board sqm 235.00
2630 Baker rod metre 5.00
2631 4 mm thick ACP sqm 1100.00
2632 Fire Stop metre 480.00
2634 GI/Aluminium Sheet (0.8 mm thick) kg 55.00
SUB HEAD : 25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
405
No.
8559 stainless steel U channel of size (50x25x2 mm) metre 160.00
8560 Non straining water resistant clear silicon metre 65.00
8945 4 Point facade glass bracket without flat head bolts Nos 3318.00
8946 2 Point facade glass bracket (wall mounted without flat head bolt) Nos 1659.00
8947 1 Point facade glass bracket (wall mounted without flat head bolt) Nos 1300.00
8948 Flate head bolt for brackets of spider glazing Nos 651.00
8949 400 mm long fin plate without fastners pair 5931.00

406
25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
No.
25.1 Providing and supplying aluminium extruded tubular and other
aluminium sections as per the architectural drawings and approved
shop drawings , the aluminium quality as per grade 6063 T5 or T6 as
per BS 1474,including super durable powder coating of 60-80 microns
conforming to AAMA 2604 of required colour and shade as approved
by the Engineer-in-Charge. ( The item includes cost of material such
as cleats, sleeves, screws etc. necessary for fabrication of extruded
aluminium frame work. Nothing extra shall be paid on this account).
The weight of aluminium extruded section shall be taken for
purpose of payment. kg 370.45
25.2 Designing, fabricating, testing, protection, installing and fixing in
position semi (grid) unitized system of structural glazing (with open
joints) for linear as well as curvilinear portions of the building for all
heights and all levels, including:
(a) Structural analysis & design and preparation of shop drawings for
the specified design loads conforming to IS 875 part III (the system
must passed the proof test at 1.5 times design wind pressure
without any failure), including functional design of the aluminum
sections for fixing glazing panels of various thicknesses, aluminium
cleats, sleeves and splice plates etc. gaskets, screws, toggles,
nuts, bolts, clamps etc., structural and weather silicone sealants,
flashings, fire stop (barrier)-cum-smoke seals, microwave cured
EPDM gaskets for water tightness, pressure equalisation &
drainage and protection against fire hazard including:
(b) Fabricating and supplying serrated M.S. hot dip galvanised /
Aluminium alloy of 6005 T5 brackets of required sizes, sections
and profiles etc. to accommodate 3 Dimentional movement for
achieving perfect verticality and fixing structural glazing system
rigidly to the RCC/ masonry/structural steel framework of building
structure using stainless steel anchor fasteners/ bolts, nylon
seperator to prevent bimetallic contacts with nuts and washers
etc. of stainless steel grade 316, of the required capacity and in
required numbers.
(c) Providing and filling, two part pump filled, structural silicone
sealant and one part weather silicone sealant compatible with
the structural silicone sealant of required bite size in a clean
and controlled factory / work shop environment, including double
sided spacer tape, setting blocks and backer rod, all of approved
grade, brand and manufacture, as per the approved sealant
design, within and all around the perimeter for holding glass.
(d) Providing and fixing in position flashings of solid aluminium sheet
1 mm thick and of sizes, shapes and profiles, as required as per
the site conditions, to seal the gap between the building structure
and all its interfaces with curtain glazing to make it watertight.
(e) Making provision for drainage of moisture/ water that enters the
curtain glazing system to make it watertight, by incorporating

407
No.
principles of pressure equalization, providing suitable gutter profiles

at bottom (if required), making necessary holes of required sizes
and of required numbers etc. complete. This item includes cost of
all inputs of designing, labour for fabricating and installation of
aluminium grid, installation of glazed units, T&P, scaffolding and
other incidental charges including wastages etc., enabling temporary
structures and services, cranes or cradles etc. as described above
and as specified. The item includes the cost of getting all the
structural and functional design including shop drawings checked
by a structural designer, dully approved by Engineer-in-charge. The
item also includes the cost of all mock ups at site, cost of all
samples of the individual components for testing in an approved
laboratory, field tests on the assembled working structural glazing
as specified, cleaning and protection till the handing over of the
building for occupation. In the end, the Contractor shall provide a
water tight structural glazing having all the performance
characteristics etc. all complete as required, as per the Architectural
drawings, as per item description, as specified, as per the approved
shop drawings and as directed by the Engineer- in-Charge.
Note:- 1. The cost of providing extruded aluminium frames, shadow
boxes, extruded aluminium section capping for fixing in the grooves
of the curtain glazing and vermin proof stainless steel wire mesh
shall be paid for separately under relevant items under this sub-
head. However, for the purpose of payment, only the actual area of
structural glazing (including width of grooves) on the external face
shall be measured in sqm. up to two decimal places.
Note:-2. The following performance test are to be conducted
on structural glazing system if area of structural glazing
exceeds 2500 Sqm from the certified laboratories accreditated
by NABL(National Accreditation Board for Testing and
Calibration Laboratories), Department of Science &
Technologies, India. Cost of testing is payable separately.
The NIT approving authority will decide the necessity of testing on
the basis of cost of the work, cost of the test and importance of the
work. Performance Testing of Structural glazing system Tests to be
conducted in the NABL accredited lab or by any other
accreditation body which operates in accordance with ISO /
IEC 17011 and accredits labs as per ISO/ IEC 17025.
1. Performance Laboratory Test for Air Leakage Test (-50pa
to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04
testing method for a range of testing limit 1 to 200 mVhr
2. Static Water Penetration Test. (50pa to 1500p) as per
ASTME- 331-09 testing method for a range up to 2000 ml.
3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA
501.01- 05 testing method for a range upto 2000 ml
4. Structural Performance Deflection and deformation by static
air pressure test (1.5 times design wind pressure without
any failure) as per ASTME-330-10 testing method for a
range upto 50 mm
408
No.
5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-

09 testing method for Qualitative test, Tests to be
conducted on site.
6. Onsite Test for Water Leakage for a pressure range 50
kpa to 240 kpa (35psi) upto 2000 ml sqm 2949.30
25.3 Providing, assembling and supplying vision glass panels (IGUs)
comprising of hermetically-sealed 6-12- 6 mm insulated glass (double
glazed) vision panel units of size and shape as required and specified,
comprising of an outer heat strengthened float glass 6mm thick, of
approved colour and shade with reflective soft coating on surface # 2
of approved colour and shade, an inner Heat strengthned clear float
glass 6mm thick, spacer tube 12mm wide, dessicants, including
primary seal and secondary seal (structural silicone sealant) etc. all
complete for the required performances, as per the Architectural
drawings, as per the approved shop drawings, as specified and as
directed by the Engineer-in-Charge. The IGUs shall be assembled in
the factory/ workshop of the glass processor.
(Payment for fixing of IGU Panels in the curtain glazing is included in
cost of item No.25.2)
For payment, only the actual area of glass on face # 1 of the glass
panels (excluding the areas of the grooves and weather silicone
sealant) provided and fixed in position, shall be measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective
soft coating on face # 2, + 12mm Airgap + 6mm Heat
Strengthened clear Glass of approved make having properties
as visible Light transmittance (VLT) of 25 to 35 %, Light reflection
internal 10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree
K etc. The properties of performance glass shall be decided by
technical sanctioning authority as per the site requirement. sqm 3250.95
25.4 Extra for openable side / top hung vision glass panels (IGUs) including
providing and supplying at site all accessories and hardwares for the
openable panels as specified and of the approved make such as
heavy duty stainless steel friction hinges, min 4 -point cremone
locking sets with stainless steel plates, handles, buffers etc. including
necessary stainless steel screws/ fasteners, nuts, bolts, washers
etc. all complete as per the Architectural drawings, as per the
approved shop drawings, as specified and as directed by the Engineer-
in-Charge. sqm 3163.10
25.5 Providing, fabricating and supplying shadow box of required size and
shape, for fixing in the spandrel portion of the structural glazing, in
linear as well as curvilinear portions of the building by providing semi
-rigid, inorganic, non-combustible fibre glass wool insulation 50 mm
thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation
layer shall have facing (factory bonded on surface # 1 of the fibre
glass insulation layer), of black non-woven fibre glass tissue of nominal
thickness 0.5 mm and nominal mass not less than 60 gm /sqm,
made of randomly oriented glass fibres distributed in a binder by a

409
No.
wet-lay process including fixing 1.5 mm thick solid aluminum sheet

backing using, 6 mm thick cement board including SS rivets, nuts,
bolts, washers etc complete. sqm 1883.55
25.6 Providing and supplying Spandrel Glass Panels comprising of 6 mm
thick heat strengthened monolithic float glass of approved colour
and shade with reflective soft coating on surface # 2 of approved
colour and shade so as to match the colour and shade of the IGUs in
the vision panels etc. ,all complete for the required performances as
specified, as per the Architectural drawings, as per the approved
shop drawings, as specified, and as directed by the Engineer- in-
Charge.
For payment, only the actual area of glass on face # 1 of the glass
panels (but excluding the area of grooves and weather silicone sealant)
provided and fixed in position, shall be measured in sqm. (Payment
for fixing of Spandrel Glass Panels in the curtain glazing is included
in cost of relevent Item*).“(i) Coloured tinted float glass 6mm thick
substrate with reflective soft coating on face # 2, having properties
as visible Light transmittance (VLT) of 25 to 35 %, Light reflection
internal 10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. . The
properties of performance glass shall be decided by technical
sanctioning authority as per the site requirement. sqm 2127.95
25.7 Item Shifted to Sub Head 8 as Item no 8.32
25.8 Design supply & installation of suspended Spider Glazing system
designed to withstand the wind pressure as per IS 875 (Part-III). The
Suspended System held with Spider Fittings of SS-316 Grade Steel
of approved manufacturer with glass panel having 12 mm thick clear
toughened glass held together with SS- 316 Grade Stainless steel
Spider & bolt assembly with laminated glass fins 21 mm thick. The
Glass fins and glass panel assembly shall be connected to Slab/
beams by means of SS- 316 Grade stainless steel brackets & Anchor
bolts and at the bottom using SS channel of 50x25x2mm using
fastener & anchor bolts, non staining weather sealants of approved
make, Teflon/ nylon bushes and separators to prevent bi-metallic
contacts, all complete to perform as per specification and approved
drawings. The complete system to be designed to accommodate
thermal expansion & seismic movements etc. The joints between
glass panels (6 to 8 mm) and gaps at the perimeter & in U channel
of the assembly to be filled with non staining weather sealant, so as
to make the entire system fully water proof & dust proof.
The rate shall include all design, Engineering and shop drawing
including approval from structural designer, labour, T&P, scaffolding,
other incidental charges including wastage, enabling temporary
services all fitting fixers nut bolts, washer, Buffer plates, fastener,
anchors, SS channel laminated glass etc. all complete. For the
purpose of payment, actual elevation area of Glazing including
thickness of joints and the portion of Glass panel inside the SS
channel shall be measured. sqm 8130.45

410
SUB HEAD : 26.0
NEW TECHNOLOGIES AND

MATERIALS
411
BASIC RATES (SH: 26.0 NEW TECHNOLOGIES AND MATERIALS)

No.
0031 Steam curing by using boiler /Heater cum 500.00
0032 Stressing Machine (jack with pump) day 11500.00
0034 Cutting saw machine day 1350.00
0035 Strands Roller machinery for laying strands day 3500.00
0036 Bed master (Pulling strands) day 3000.00
0037 Mobile crane day 7500.00
0044 Cost for crane upto 40 tonne capacity day 8000.00
0072 Cost for crane having capacity 50MT day 8500.00
0086 Compressor, gun, rubber pipes & other accessories- hire charge
of plant & machinery i/c necessary fuel day 4000.00
0088 Hire charges of Drill machine upto 30 mm dia day 160.00
0089 Hire charges of sand blasting equipment day 160.00
0090 Hire charges of compressor day 420.00
0091 Welding charges of shear key to existing reinforcement each 5.00
0092 Hire charges of plant and Machinery that can inject 350 kg/day day 200.00
SUB HEAD : 26.0 NEW TECHNOLOGIES AND MATERIALS

412
No.
0127 Driver for (Road roller, concrete mixer, Trucks etc.) day 738.00
0128 Mate day 617.00
0132 Rock Excavator day 558.00
0133 Rock Breaker day 558.00
0135 Stone Chiseller day 617.00
0154 Nozzel man/ gun man day 738.00
0238 6 mm thick heavy duty fiber cement board sqm 470.00
0239 8mm thick heavy duty fiber cement board sqm 300.00
0241 12.5 mm thick Gypsum plaster board sqm 170.00
0244 Factory made light weight composite non asbestos fibre reinforced
aerated cement sandwitched wall/roof panel (50mm thick). The outer
face on both sides of the panels will be non asbestos fibre cement
board (minimum 4mm thick) confirming to IS 14862:2000 sqm 634.00
0245 Factory made light weight non asbestos fibre reinforced aerated
cement sandwitched wall/roof panel (75mm thick). The outer face
on both sides of the panels will be non asbestos fibre cement
0246 2mm thick sim pad each 10.00

413
No.
0764 Calcium silicate base compound for jointing calcium silicate tiles kg 26.00
0993 FY-1860 grade wire strands quintal 5700.00
1012 Pregalvanized high tensile steel confirming to IS:277-199 kg 90.00
1021 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not less
than 7.75 kg/sqm sqm 430.00
1027 Erection Bolts ( Minimum 04 nos for each element) each 25.00
1217 GI Wire mesh 100x100 mm kg 75.00
1218 Shear stud each 50.00
1223 Steel weld mesh sqm 150.00
1246 Silicon based Joint Sealant for Tiles kg 160.00
1247 Rubber base Adhesive kg 223.00
1248 Epoxy based sealing Compound kg 535.00
1249 Acrylic based sealing compound kg 500.00
1250 Non woven reinforcement Tape metre 0.14
1251 M-60 grade cemetitious grout (Non Shrink) kg 28.00
1252 Cementitious polymer base adhesive confirming to EOTA
ETAG 004 (European Technical Approval) kg 34.00
1253 Polypropylene mechanical fastener with plastic pin confirming
to EOTA ETAG 014 (European Technical Approval) having dia
10mm & L=200mm each 30.00
1254 Moisture cure Polyurethane Foam 750 ml 600.00
1255 PVC Corner Bead of size 25mmx25mm fixed with glass fibre
mesh (100mm x 100mm) metre 90.00
1256 Cementitious polymer base coat confirming to EOTA ETAG 004
(European Technical Approval) kg 40.00
1257 Fiberglass mesh with alkali-resistant coating having mass per
unit area ?145 g/m2, mesh size: 3.9x4.0 mm ±10% sqm 75.00
1316 50mmx50mm hardwood plug each 75.00
2261 Carriage of Fine sand (1 Part badarpur sand : 2 parts jamuna sand) cum 103.77
2358 Carriage of Bamboo Mat corrugated sheets and accessories tonne 11500.00
2491 Pre laminated both side solid foam uPVC profile (45x20mm) metre 130.00
2492 Solid foam uPVC sheet 20mm thick pre laminated on both side sqm 2090.00
2493 PVC edge beading metre 31.00
2494 Expandable fastner with plastic sleeve each 5.00
2635 GI Screws of gauge 10, length 25 mm for fixing cement fibre
board to C section each 3.00
414
No.
2636 GI Screws of gauge 10, length 45 mm for fixing cement fibre
board to C section each 3.00
2637 Vapour barrier sqm 175.00
7009 12.5 mm thick tapered edge gypsum plain borad sqm 155.00
7025 Self tapping pan head nickel coated mild steel screws of size
13 x 3.2 mm 1000 Nos 525.00
7026 Fibre joint tape 50 mm wide (90 metre) roll each roll 165.00
7274 Glass wool 50 mm thick sqm 238.00
7336 Lock Bar (E 250) - 10 thick MS Plate kg 76.00
7367 Galvanised M.S. sheet 0.5 mm thick pressed channel section
of size 50x32 mm metre 57.00
7368 GFRG Panel of 124 mm thick sqm 847.46
7369 Galvanised M.S. sheet 0.50 mm thick pressed stud : 48x34x
36 mm metre 71.00
7383 12 mm dia 50 mm long wedge type expanded zinc alloy dash
fastener each 7.00
7776 Concrete paver block of grade M-30 made of C&D waste (60mm
thickness) sqm 317.22
7911 Chemical Rust Remover litre 210.00
7913 Epoxy kg 585.00
7914 SBR Polymer kg 190.00
7915 Woven PVC cloth sqm 25.00
7917 Hire charges of compressure day 645.00
7918 25mm thick cement concrete shotcrete(guniting) with compressor sqm 105.00
7921 Adhesive chemical ml 2.00
7922 Bit of drilling machine for Hole upto 30mm dia each 500.00
7923 GI injection nipple 12mm dia, 75mm long each 42.00
7924 Blowing compressed air for cleaning holes upto 30mm dia each 10.00
7925 L shaped 100mm long, 10mm dia mild steel shear key kg 67.00
7927 Acrylic Polymer chemical for cracks kg 31.00
7929 Shear loops (6mm dia GI wire rope) (For vertical joints) 6 nos
on each side each 192.00
7930 dowel tubes (Corrugated GI pipes 50 to 80mm dia) (For horizontal
joints) metre 120.00
7931 Hooks for lifting (Alloy steel) having 2.5 tonne capacity each 250.00
7996 Factory made EPS light weight composite sandwitched wall/
roof panel (50mm thick) having core material of EPS granule
balls/beads (conforming to IS 4671:1984 and shall have density

415
No.
not less than 15kg per cum). The outer face on both sides of the
panels will be non asbestos fiber cement board confirming to IS
14862:2000 or Calcium silicate board confirming to EN
14306:2009 of 5mm thick each. sqm 735.25
panels will be non asbestos fiber cement board confirming
to IS 14862:2000 or Calcium silicate board confirming to EN
14306:2009 of 5mm thick each sqm 845.00
8013 Factory made EPS Core wallpanel /roof panel sandwiched be-
tween two Engineered welded wire fabric mesh of 3 mm dia G.I.
wire mesh,with 50 mm pitch in both the directions, kept at 120-
135 mm gap and interconnected by the zig zag G.I. wire of 3
mm dia at alternate row by welding. sqm 1650.00
8015 Expanded poly ethylene Foam sheet 4mm thick of Density
40kg/m3 sqm 18.00
8016 High Density expanded poly ethylene (EPE) Foam 1mm thick sqm 8.50
8019 GI sheet 0.8 mm thick confirming to IS 277:1992 kg 75.00
8020 Factory made EPS Core wall panel /roof panel sandwiched be-
tween two Engineered welded wire fabric mesh of 3 mm dia G.I.
wire mesh, with 50 mm pitch in both the directions, connected
by G.I. wire of 3mm dia at alternate row by welding sqm 600.00
8021 Bamboo wood Tile Flooring 14mm thick of minimum size 1800mm
x130mm sqm 3470.00
8022 Bamboo wood Quarter Round 18mm thick of size 1900mm x 18mm metre 112.00

416
No.
8023 Bamboo wood door reducer 14mm thick of size 1900mm x 44mm metre 255.00
8024 Bamboo wood Skirting 14mm thick of Size 1900mm x 85mm metre 300.00
8025 Bamboo wood Tile Wall Cladding 10mm thick of size 1900mm x
135mm sqm 3385.00
8026 Bamboo wood T-mold 14mm thick of size 1900mm x 44mm metre 250.00
8027 Bamboo wood Threshold 14mm thick of size 1900mm x 44mm metre 255.00
8028 Bamboo wood shutter of doors 10 cudm 1700.00
8029 Bamboo wood panelling (10mm thick) 10 cudm 1680.00
8030 Superior class Bamboo wood door frame 65 mm thick, 10 cudm 1675.00
8031 Aluminium sheets Grade 5052, 4 mm thick for wall panel/deck
panel/WRB panel/Kicker Panels/door closing panels ( for form
work) sqm 8500.00
8032 Aluminium sheets Grade 5052, 4 mm thick for Internal Corner/
Column Corners/ ( for form work) sqm 11500.00
8033 Aluminium sheets Grade 5052, 4 mm thick for Mid Soldier/End
soldier (for form work) sqm 32000.00
Accessories for aluminium form work
8034 External corner 2050 mm each 1400.00
8036 soldier tie 370mm each 290.00
8037 Adjustable prop-2.0 x2.0 m each 1080.00
8038 Pin-50 each 15.00
8039 Pin-127 each 55.00
8040 wedge each 14.00
8041 wall tie-150 (355 mm ) each 45.00
8042 Polythene Sleeve 90 x 150mm each 3.00
8043 Polythene Roll - 150mm Long. each 6.00
8044 Vertical Soldier -1100mm each 365.00
8045 Wall Attached Bracket 600x1000mm each 985.00
8046 Allignment Pipe - 3.00 Mtr. each 995.00
8047 Allignment Bracket each 475.00
8048 Tie Rod for Bracket - 500mm each 115.00
8049 Anchor Wing Nut Ø100 mm each 64.00
8050 Debit Pin - 250mm each 60.00
8051 PVC Pipe Ø20mm - 150mm long each 5.00
8052 PVC Cone each 5.00
8053 Bolt+Nut - 16 x 80 mm each 30.00
8054 Flat Washer Ø16, 3mm thik each 5.00
8055 Bolt+Nut - 16 x 30 mm each 18.00

417
No.
8056 Door spacer 45x45x5-1135mm Long each 360.00

8144 Bamboo Mat corrugated sheets 3.5 to 4mm thick conforming to
IS 15476:2004 sqm 2648.00
8145 Bamboo Mat Ridge cap 3.5 to 4mm thick conforming to IS
15476:2004 metre 2570.00
8146 3mm thick Bamboo Mat Board conforming to IS 13958:1994 sqm 1508.00
8210 Stainless steel screws 50 mm 100 Nos 270.00
8215 Stainless steel butt hinges 125x64x1.9 mm IS : 12817 marked 10 Nos 265.00
8226 Concealed zinc coated hinges 19-20 mm thick with mounting
plate 10 Nos 420.00
8514 40 mm long S.S screws with plastic rawl plugs 100 40.00
8515 Galavanised MS 8 mm outer diameter M-6 dash fastener 50mm
long each 31.00
8516 ZMB 60/equivalent kg 105.00
8517 ZMB thinner litre 205.00
8518 Zycoprime / equivalent litre 210.00
8519 Zycosil / equivalent litre 1800.00
8520 Elastobar / equivalent kg 300.00
8552 Mineral fibre beveled tegular edged ceiling tiles 595 x595mm,
16 mm thick sqm 830.00
8553 Mineral fibre beveled tegular edged ceiling tiles 595 x595mm,
16 mm thick with bio-block conforming to ISO 5 (class 100)
specifications. sqm 920.00
8554 Mineral fiber beveled tegular edged ceiling tiles 595 x595mm,
20 mm thick. sqm 1040.00
8555 G.I main runner 15 x32 mm of 3000 mm length, 0.33 mm thick each 185.00
8556 G.I cross-T 15 x32 mm of 1200 mm length, 0.33 mm thick each 78.00
8558 G.I hanger rod 6mm dia fully threaded upto 1000 mm length each 26.00
8559 Stainless steel U Channel of size (50x25x2mm) metre 160.00

418
No.
8560 Non staining water resistant clear silicon metre 65.00

8561 Extruded polystyrene rigid insulation board 50 mm thick sqm 525.00
8562 Expanded Polystyrene insulation board 120 mm thick confirm-
ing to IS 4671-1984, Fire retardant property self-extinguishing
type as per EN 13501-1 sqm 800.00
8563 15 mm thick, light weight, integral densified micro look edged,false
ceiling tiles of size 595x595 mm. sqm 720.00
8564 15 mm thick, light weight,fully perforated square/butt edge inte
gral densified,false ceiling tiles of size 595x595 mm. sqm 900.00
8565 Galavanised MS hanger rod 6 mm dia MS fully threaded up to
1000mm length each 26.00
8566 Powder coated steel section main-T ceiling sections 15x42x0.40
mm (3000 mm long) each 235.00
8567 Galvanized mild steel perimeter wall angle 22x19x0.40 mm
(3000mm long) each 115.00
8568 Powder coated Galvanised Iron intermediate cross-T section
15x42x0.40 mm (1200 mm long) each 95.00
8569 Powder coated Galvanized Iron intermediate cross-T section
15x42x0.40mm (600 mm long ) each 47.00
8570 GI Main T ceiling section 30x25x0.3 mm (3 metre long) each 187.00
8571 GI Perimeter wall angle 25x25x0.4 mm (3 metre long) each 157.00
8572 GI Intermediate cross T section 25x25x0.3 mm (1.2 metre long) each 72.00
8579 Cold form light gauge Steel C-section of thickness 0.75mm i/c
zink coating/sliting etc. kg 130.00
8580 Wastage of cold form light gauge steel kg 17.00
8581 12 mm thick micro tegular edged semi perforated GRG (Glass
Fibre Reinforced Gypsum) false celing tiles of Size 595x595 mm sqm 510.00
8582 12 mm thick micro tegular edged fully perforated GRG (Glass
Fibre Reinforced Gypsum) false celing tiles of Size 595x595 mm sqm 600.00
8583 10 mm thick square edge fully perforated GRG(Glass Fibre Re
inforced Gypsum) false celing tiles of Size 595x595 mm sqm 750.00
8587 Galvanized iron intermediate cross-T section 15x32x0.33 mm
(600mm long) each 35.00
8588 Galavanised MS hanger rod 6mm dia MS fully threaded up to
1000mm length each 26.00
8589 Calcium Silicate tegular edged celling tiles 595x595 mm and
15 mm thick on edges sqm 685.00
8590 Galvanised Steel main Tee ceiling section Size 24x38x0.33 mm
(3 metre long) each 120.00
8591 Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm
(3.00 metre long) each 65.00

419
No.
8592 Galvanised Steel intermediate cross T section Size 24 x 25 x

0.33mm (1.2 metre long) each 40.00
8593 Galvanised Steel intermediate cross T section Size 24 x 25 x
0.33mm (0.6 metre long) each 20.00
8594 Galvanised Steel soffit cleat size 25x35x1.60 mm each 4.00
8595 Wooden screws with plastic rawl plugs 35x8 mm each 1.00
8596 Galvanised MS 8mm outer diameter M-6 dash fastener 25mm long each 32.00
8597 GI Metal Tile Clip in Plain Beveled edge global white colour tiles of
size 600x600 mm and 0.5 mm thick sqm 677.00
8598 GI Metal Tile Clip in Perforated Beveled edge global white colour tiles
of size 600x600 mm and 0.5 mm thick sqm 782.00
8604 Spring T-section 24x34x0.45 mm (3.00 meter long) metre 190.00
8605 C Wall angle section 20x30x20x0.50 mm (3.00 meter long) metre 95.00
8606 Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long) metre 115.00
8607 Spring T-connector each 5.00
8608 C Carrier Connector each 11.00
8609 C Suspension Clip each 8.00
8610 Wire Coupling Clip each 9.00
8611 Main T ceiling sections 24x38x0.3 mm (3 metre long) each 115.00
8612 Perimeter wall angle 24 x 24 x 0.3 mm (3 metre long) each 80.00
8613 Intermediate cross T-Section 24x25x0.3 mm (1.2 m long) each 35.00
8615 Hanger rod 4 mm thick each 8.00
8616 Adjustment clip 85x30x0.8 mm each 5.00
8617 Soffit cleat (Size 27x37x25x1.60 mm) each 4.00
8618 Dash fastener 6 mm dia 50 mm long each 8.00
8619 Galavanised MS L-shape level adjuster of size 85x25x2 mm each 15.00
8658 Precast C&D waste concrete block 1000 Nos 25150.00
8659 Water proof ply 12 mm thick sqm 517.00
8684 White sand stone gang saw cut 30 mm thick sqm 560.00
8761 Scaffolding net made of high density polyethylene UV stabilized having
density 100gm/ sqm. sqm 21.50
8956 Bi-Axial Extruded GeoGrids of Minimum Tensile Strength 15 kN/m
in the longitudinal and transverse direction sqm 100.00
8957 Bi-Axial Extruded GeoGrids of Minimum Tensile Strength 20kN/m

420
No.
8960 Geosynthetic Drainage with two filtering nonwoven geotextiles

having a “W” configuration as longitudinal parallel channels. Mini-
mum thickness to be 7.2mm, with two filtering UV stabilized
polypropylene nonwoven geotextile of minimum thickness of
0.75mm having pores of 150 micron and tensile strength of 8.0
kN/m and having plane flow capacity of 2.1 L / (m.s) at hydraulic
gradient of 1.0 & 20 kPa pressure,tensile strength of 18 kN/m ,
with mass per unit area of 740 gsm. sqm 530.00
8961 Geosynthetic Drainage Composite having thermobonding a drain-
ing core - HDPE geonet comprises of two sets of parallel overlayed
ribs integrally connected to have a rhomboidal shape with a
polyethylene film and a nonwoven geotextile having mass per
unit area 130 g/m2 and tensile strength of 8.0 kN/m having in
plane flow capacity of 0.7 L / (m.s) at hydraulic gradient of 1.0 &
20 kPa pressure and tensile strength of 13.5 kN/m , with mass
per unit area of 830 gsm, sqm 630.00
8962 Synthetic Geogrid having Ultimate tensile strength- 100 kN/m sqm 220.00
8963 Synthetic Geogrid Ultimate tensile strength- 150 kN/m sqm 230.00
8966 Synthetic Geogrid Ultimate tensile strength- 300kN/m sqm 365.00
8977 Aluminium profile industrial troughed sheet of Alloy 31500/31000/
40800, conforming to IS 1254, IS 737, IS 2676, 0.71 mm thick,
the profile detail width 1044/920 mm, cover width 1000/875 mm. sqm 600.00
40800, conforming to IS 1254, IS 737, IS 2676, 0.91 mm thick,
the profile detail width 1044/920 mm, cover width 1000/875 mm. sqm 785.00

421
26.0 NEW TECHNOLOGIES AND MATERIALS
No.
26.1 Providing & fixing in position Phenol bonded Bamboowood flooring
with planks of sizes 14mm thick, 1800mm length (minimum) and
130 mm wide(minimum), in approved colour, texture and finish,
having Performance Appraisal Certificate (PAC) issued by Building
Materials & Technology Promotion Council (BMTPC). The flooring
shall be fixed with tongue and groove interlocking system, with
underlayment of 4mm thick expanded polyethylene foam sheets
having density 40kg/cum, over prepared surface with necessary
quarter round planks of size 1900mm x 18mm and door reducer of
size 1900mm x 44mm, wherever required. The bamboowood planks
shall have minimum density of 1000 Kg/cum & minimum Hardness
1000 Kgf. with Eco friendly UV coating, all complete as per direction
of the Engineer in-charge. sqm 5279.10
26.2 Providing & fixing in position Phenol bonded Bamboowood in wall
skirting with planks of sizes 14mm thick, 1900mm length (minimum)
and 85mm wide(minimum), in approved colour, texture and finish,
having Performance Appraisal Certificate (PAC) issued by Building
Materials & Technology Promotion Council (BMTPC). The skirting
shall be fixed with SS screws & rawl plugs, over underlayment of
4mm thick, expanded polyethylene foam sheets having 40kg/cum
density over prepared surface. The bamboowood planks shall have
minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf.
with Eco friendly UV coating, all complete as per direction of the
Engineer in-charge. sqm 5162.75
26.3 Providing & fixing in position Phenol bonded Bamboowood wall
cladding at all height with planks of sizes 10mm thick, 1800mm
length (minimum) and 130 mm wide (minimum), in approved colour,
texture and finish, having Performance Appraisal Certificate (PAC)
issued by Building Materials & Technology Promotion Council
(BMTPC), with necesasary profiled edges fixed with 40mm SS screws
5 nos in each tile to frame work made of second class teak wood of
size 20x15 mm in centre of each tile and bottom and top of work
height, 40x15mm placed at ends of each tile. The cladding shall be
laid over backlayment of 1.00 mm thick expanded polyethylene foam
of density 40kg/cum in two layers, first layer on wall surface before
fixing wooden frame and second layer on frame under cladding. The
bamboowood planks shall have minimum density of 1000 Kg/cum
& minimum Hardness 1000 Kgf. with Eco friendly UV coating, all
complete as per direction of the Engineer in-charge. sqm 5559.40
26.4 Providing & fixing in position Phenol bonded Bamboowood panelled
or panelled and glazed shutters for doors windows, clerestorey
windows with pre-molded 30mm thick planks, in approved colours,
texture & finishe. It shall have 10mm wide, 25mm deep grove to fit in
panels.The bamboo wood shall have minimum density of 1000 Kg/
cum, minimum Hardness 1000 Kgf. All styles and rails shall have
profiled interlocking system locked in place by bamboo pins, all
complete as per direction of Engineer in charge. (The panelling will
be paid for separately). sqm 5460.25

422
No.
26.5 Providing & fixing in position Phenol bonded Bamboowood panelling

of 10mm thick, in 25 to 40 mm thick panelled or panelled & glazed
shutters for doors, windows, clerestorey windows, in approved colour,
texture & finish. The bamboowood planks shall have minimum
density of 1000 Kg/cum & minimum Hardness 1000 Kgf. The panels
shall have profiled interlocking system locked in place with bamboo
pins all complete as per direction of the Engineer in-charge. (area
of opening for panel inserts excluding portion inside grooves or rebates
to be measured) sqm 3561.70
26.6 Providing & fixing in position 65 mm thick factory made door frame of
Phenol bonded Bamboo wood (superior class, interior use), in
approved colour, texture and finish.The bamboo wood shall have
minimum density of 1000 Kg/cum, minimum hardness 1000 Kgf.
The door frame shall have tenon & mortise interlocking system, to
be fixed to the wall with 100 mm size G.I screws all a complete as
per direction of Engineer-in charge. cudm 254.00
26.6A Providing, erecting, laying and fixing in position in 3.5 to 4
mm thick bamboo mat corrugated sheet (BMCS) as per IS:
15476-2004 in roofing with self drilling screws along with EPDM
washers complete or with galvanized iron J or L hooks 8mm
dia G.I. plain and bitumen washers etc, all complete as per
direction of Engineer-in-Charge. sqm 5128.90
26.6B Providing and fixing in position ridges of 3.5 to 4 mm thick
bamboo mat ridge cap (BMRC) as per IS: 15476-2004 in roofing
with self drilling screws along with EPDM washers complete
or with galvanized iron J or L hooks 8mm dia G.I. plain and
bitumen washers etc, all complete as per direction of Engineer-
in-Charge. metre 4147.25
26.6C Providing and fixing at all height false ceiling of 4mm thick
phenol bonded Bamboo Mat board (595x595mm) conforming
to IS:13958-1994 including providing and fixing of frame work
made of GI angle 25x25x0.4 mm thick all around suitably fixed
to wall with the help of dash fastener and hanger frame
(600x600 c/c) made GI slotted Tee having powder coating on
bottom side (30x25x0.3 mm thick for main member & 25x25x0.3
mm for cross member) connected to ceiling with 2.64mm GI
wire and anchor fastener at every junction and also including
cost of making openings for light fittings, grills, diffusers, cut
outs made with frame of perimeter channels suitably fixed all
complete as per direction of Engineer-in-charge. sqm 3271.75
26.6D Providing and fixing at Bamboo Mat board conforming to IS:13958-
1994 for partition to frame by bucking or studding with screws
etc. complete (Frames, backing or studding to be paid separately)
26.6D.1 3mm thickness sqm 2396.20

423
No.
26.6E Providing and fixing at all height wall panelling with phenol
bonded Bamboo Mat board conforming to IS:13958-1994
including providing and fixing to frame work made of 50mm x
50mm hardwood plugs including cutting brick work and fixing
in cement mortar and making good the wall etc. and also
providing and fixing wooden moulded corner beading of
triangular shape to the junction of panelling etc. with iron
screws all complete as per direction of Engineer-in-Charge.
26.6E.1 9mm thickness sqm 4443.65
26.6E.2 12mm thickness sqm 5066.55
26.7 Providing and fixing 50 mm thick extruded polystyrene rigid insulation
board of required size between cavity wall, complying with ISO
4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity
of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346),
compressive strength of > 350 kPa listed as per ASTM D 1621,
density of 34-36 kg/m³ as per ASTM D 1622, water absorptions <
1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1
listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per
ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of
class B2 and as per ASTM E84 class A, fixed with suitable water
based adhesive and fastener, complete in all respect as per the
direction of Engineer- in-Charge. sqm 807.20
26.8 Providing and fixing 50 mm thick extruded polystyrene rigid insulation
board of required size underdeck on ceiling surface, complying with
ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal
conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per
IS 3346), compressive strength of > 350 kPa listed as per ASTM D
1621, density of 34-36 kg/cum as per ASTM D 1622, water
absorptions < 1% by volume as per ASTM D 2842, oxygen index of
24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia
(max) as per ASTM D 3576. Fire retardent property as per DIN 4102,
Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable
water based adhesive and fastener, complete in all respect as per
the direction of Engineer-in-Charge. sqm 871.20
26.9 Providing and fixing factory made solid Foam uPVC profile for kitchen
cabinet frame (45 x 20 mm) of approved shade, quality and make.
The profile shall be laminated on both sides, made from rigid foam
sheets (Single extruded) having density 600 Kg/cum and the exposed
edges sealed with PVC edge beading of same shade and colour.
The frame shall be fire retardent with necessary screw holding
capacity. Frame shall be fixed to wall using Expendable Fastner
with necesary stainless steel screws, all complete as per direction
of Engineer-in-charge. metre 377.00
26.10 Providing and fixing factory made Kitchen Cabinet Shutter/Partition
20 mm nominal thickness of approved shade, quality and make,
made from rigid foam sheets (Single extruded) having density 600
Kg/cum and laminated on both side by laminate Sheet/PVC foil
lamination. The exposed edges shall be sealed with PVC edge
beading of same shade and colour. The shutter shall be fire retardent
424
No.
having necessary screw holding capacity. Shutter shall be fixed to

frame using approved hinges with necessary stainless steel screws,
all complete as per direction of Engineer-in-charge. sqm 4535.30
26.11 Providing and fixing concealed hinge of approved quality for 19-20mm
thick door with stainless steel screws complete : each 105.25
26.12 Supplying & laying of bi-axial extruded high modulus polypropylene
geogrid coforming to MORTH SPECIFICATION for base/sub-base
reinforcement having minimum tensile strength 15kN/m in the
longitudinal and transverse direction, with 5kN/m and 7kN/m tensile
strength at 2% and 5% strain respectively in the longitudinal and
transverse direction, junction efficiency not less than 95% and with
38mm X 38mm mesh opening. sqm 171.35
longitudinal and transverse direction, with 10.5kN/m and 21kN/m
tensile strength at 2% and 5% strain respectively in the longitudinal
and transverse direction, junction efficiency not less than 95% and
with 38mm X 38mm mesh opening. sqm 296.45
26.16 Supplying & laying of drainage composite for use behind walls,
between two different fills, alongside drains of road, below concrete
lining of canals etc. Geocomposite for planar drainage, realized by
thermobonding a draining core in extruded monofilaments with two
filtering nonwoven geotextiles that may also be working as separation
or protecting layers. The draining three dimensional core will have a
“W” configuration as longitudinal parallel channels. Minimum
thickness to be 7.2mm, with two filtering UV stabilized polypropylene
nonwoven geotextile of minimum thickness of 0.75mm characteristic
opening size (090) of 110 micron and tensile strength of 8.0 KN/m
that will be working as separation or protecting layer, geocomposite
having in plane flow capacity of 2.1 L / (m.s) at hydraulic gradient of
1.0 & 20 kPa pressure and tensile strength of 18 kN/m , with mass
per unit area of 740 gsm, supplied in the form of roll for easy
transportation to site of work as per detailed specification all complete
as per directions of Engineer in charge. sqm 804.20
425
No.
26.17 Supplying & laying of drainage composite for use behind walls,
between two different fills, alongside drains of road, below concrete
lining of canals etc. having thermobonding a draining core - HDPE
geonet comprises of two sets of parallel overlayed ribs integrally
connected to have a rhomboidal shape with a polyethylene film and
a nonwoven geotextile having mass per unit area 130 gsm and
tensile strength of 8.0 kN/m that will be working as separation or
protecting layer, geocomposite having in plane flow capacity of 0.7 L
/ (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile
strength of 13.5 kN/m , with mass per unit area of 830 gsm, at
easily accessible location including top and bottom, with all leads
and lifts, manpower and machinery, materials, labour etc. complete
and as directed by Engineer - In - Charge. sqm 951.35
26.18 Supplying and laying high strength flexible geogrids (HSFG) as soil
reinforcement / basal reinforcement as per MORTH 3100 and IRC
113, made of high tenacity polyester core with polyethylene coating
with Minimum Long Term Design Strength (LTDS) of more than 50%
of ultimate tensile strength at 30 degree Celcius corresponding to 12
% strain .
26.18.1 Ultimate tensile strength- 100 kN/m sqm 347.95
26.19 Providing at all heights, levels and locations Aluminium profile
industrial troughed sheet of Alloy 31500/31000/40800, conforming to
IS 1254, IS 737, IS 2676. The sheet shall be fixed using self drilling/
self tapping SS screws of size 5.5x65 mm with EPDM seal complete
upto required pitch in horizontal, vertical or curved surfaces i/c cutting
to size and shape where required as per specifications, detail
drawings and direction of Engineer-in-Charge. The rate shall be
inclusive of all screws, seal, ridge, labour, scaffolding, machinery for
fixing and approved sealent where required etc. but excluding the
cost of purlins, rafters and trusses.

426
No.
26.19.1 0.71 mm thick, the profile detail width 1044/920 mm,

cover width 1000/875 mm. sqm 976.05
26.19.2 0.91 mm thick, the profile detail width 1044/920 mm,
cover width 1000/875 mm. sqm 1239.55
26.22 Providing and fixing false ceiling at all heights with integral densified
calcium silicate reinforced with fibre and natural filler false ceiling
tiles of Size 595x595mm of approved texture, design and patterns
having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per
IS 8225:1987, Light reflectance of 85% (minimum). Non combustible
as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7),
humidity resistance of 100%, thermal conductivity < 0.043 W/m K
as per ASTM 518:1991,in true horizontal level suspended on inter-
locking metal T-Grid of hot dipped galvanised iron section of 0.33mm
thick (galvanized @ 120 grams per sqm including both sides)
comprising of main-T runners of size 24x38 mm of length 3000 mm,
cross - T of size 24x32 mm of length 1200 mm and secondary
intermediate cross-T of size 24x32 mm of length 600mm to form
grid module of size 600 x 600 mm, suspended from ceiling using
galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e.
50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia
fully threaded hanger rod upto 1000 mm length and L-shape level
adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall
angle of size 24x24x0.40 mm of length 3000 mm to be fixed on
periphery wall / partition with the help of plastic rawl plugs at 450
mm center to center and 40 mm long dry wall S.S screws. The work
shall be carried out as per specifications, drawing and as per directions
of the Engineer-in-Charge.
26.22.1 With 15 mm thick tegular edged light weight calcium
silicate false ceiling tiles. sqm 1688.80
26.23 Providing and fixing false ceiling at all heights with integral densified
calcium silicate reinforced with fibre and natural filler false ceiling
tiles of Size 595x595 mm of approved texture, design and patterns
having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per
IS 8225:1987, Light reflectance of 85% (minimum). Non combustible
humidity resistance of 100%, thermal conductivity < 0.043 W/m K
as per ASTM 518:1991, in true horizontal level suspended on inter-
locking metal powder coated T-Grid of hot dipped galvanised iron
section of 0.40 mm thick on Silhouette profile,rotary stiched double
webbed white with 6mm reveal profile (white/black),comprising of
main-T runners of size 15x42mm of length 3000 mm, cross - T of
size 15x42 mm of length 1200 mm and secondary intermediate cross-
T of size 15x42 mm of length 600mm to form grid module of size
600 x 600 mm, suspended from ceiling using galvanised mild steel
items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm
outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger

427
No.
rod upto 1000 mm length and L-shape level adjuster of size 85x25x2
mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of
length 3000 mm to be fixed on periphery wall / partition with the help
of plastic rawl plugs at 450 mm center to center and 40mm long dry
wall S.S screws. The work shall be carried out as per specifications,
drawing and as per directions of the Engineer-in-Charge.
26.23.1 With 15 mm thick integral densified micro edge light
weight calcium silicate false ceiling tiles sqm 1952.70
26.24 Providing and fixing in position wall panelling at all heights with integral
densified calcium silicate panels/tiles of size 595 x 595mm, having
NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS
8225:1987, Light reflectance of 85% (minimum). Non combustible
humidity resistance of 100%, thermal conductivity <0.043 W/m K
as per ASTM 518:1991, comprising of a frame made from especially
fabricated galvanised mild steel sheet 0.50 mm thick pressed section
(galvanizing @120 grams per sqm including both sides) i.e.vertical
studs of size 48 x 34 x 36 mm are placed at 600mm center to center
in a floor and ceiling channel section of size 50 x 32m fixed to the
floor and soffit at 600mm centers using 12mm dia,50mm long wedge
type expanded zinc alloy dash fastner with 10mm bolt. This same
channel is then to be fixed in horiziontal direction at 600mm center
to center so as to form a grid of 600mm x 600mm. Glasswool of
50mm thickness is then to be inserted in the slots and finally calcium
silicate non combustible panels/tiles are to be screw fixed with self
tapping pan head nickel coated mild steel screws of size 13 x 3.2mm
on to this grid leaving an even groove of 1 mm between the panels.
The joints between the panels are to be duly jointed and finished
using recommended jointing calcium silicate based compound and
fiber joint tape roll 50mm wide (90 metre )roll and two coats of
primer suitable for panelling as per manufacturer’s specification as
per direction of Engineer-in-Charge all complete.
26.24.1 With 15 mm thick fully perforated square/butt edge light
weight calcium silicate panels/ tiles sqm 2736.80
26.25 Providing and fixing 15 mm thick false ceiling tiles at all heights
with integral densified calcium silicate reinforced with fibre and natural
filler false ceiling tiles of Size 595x595 mm of approved texture, design
and patterns having NRC (Noise Reduction coefficient) of 0.50
(minimum) as per IS 8225:1987, Light reflectance of 85% (minimum).
Non combustible as per BS:476 (part-4), fire performance as per
BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity
< 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the
existing frame work consisting of T-sections and Lsections suitably
fixed according to tile size as per direction of Engineer-in-charge. sqm 1379.10
26.26 Providing & fixing false ceiling at all heights with GRG (Glass Fibre
Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of
approved texture, design and patterns having moisture content less
than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS
8225:1987, Non combustible as per BS 476 (part 4)-1970 and light

428
No.
reflectance of 85% (minimum) to be laid in true horizontal level

suspended on inter-locking metal T-Grid of hot dipped galvanised
iron section of 0.33mm thick (galvanized @ 120 grams per sqm
including both sides) comprising of main-T runners of size 15x32
mm of length 3000 mm, cross - T of size 15x32 mm of length 1200
mm and secondary intermediate cross-T of size 15x32 mm of
length 600mm to form grid module of size 600 x 600 mm, suspended
from ceiling using galvanised mild steel items (galvanizing @ 80
grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash
fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length
and L-shape level adjuster of size 85x25x2 mm. Galvanised iron
perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to
be fixed on periphery wall / partition with the help of plastic rawl
plugs at 450 mm center to center and 40 mm long dry wall wood
screws. The work shall be carried out as per specifications, drawing
and as per directions of the Engineer-in-Charge.
26.26.1 With semi perforated 12 mm thick micro tegular edged
GRG false ceiling tiles. sqm 1572.85
26.26.2 With fully perforated 12 mm thick micro tegular edged
or 10 mm thick square edged GRG false ceiling tiles. sqm 1699.30
26.27 Providing and fixing mineral fibre false ceiling tiles at all heights of
size 595X595mm of approved texture, design and pattern. The tiles
should have Humidity Resistance (RH) of 99%, Light Reflectance >
85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance
as per (BS 476 pt - 6 &7)in true horizontal level suspended on
interlocking T-Grid of hot dipped all round galvanized iron section of
0.33 mm thick (galvanized @120 gsm) comprising of main T runners
of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length
1200 mm and secondary intermediate cross T of size 15x32 mm of
length 600 mm to form grid module of size 600x600 mm suspended
from ceiling using galvanized mild steel item (galvanised@80gsm)
50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter
fully threaded hanger rod up to 1000 mm length and L-shape level
adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre
along main ‘T’. The system should rest on periphery walls /partitions
with the help of GI perimeter wall angle of size24x24X3000 mm made
of 0.40 mm thick sheet, to be fixed to the wall with help of plastic
rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S.
screws. The exposed bottom portion of all T-sections used in false
ceiling support system shall be pre-painted with polyester baked
paint, for all heights. The work shall be carried out as per
specifications, drawings and as per directions of the engineer-in-
charge.
26.27.1 With 16 mm thick beveled tegular mineral fibre false
ceiling tile (NRC 0.55 to 0.6 sqm 2000.85
26.27.2 With 20 mm thick beveled tegular mineral fibre false
ceiling tile (NRC 0.7) sqm 2296.85
26.27.3 With 16 mm thick beveled tegular mineral fibre Anti-
microbial false ceiling tile confirming to ISO 5 (class
100 ) specifications sqm 2128.25
429
No.
REPAIR AND REHABILITATION ITEMS

26.28 Chipping of unsound/weak concrete material from slabs, beams,
columns etc. with manual Chisel and/ or by standard power driven
percussion type or of approved make including tapering of all edges,
making square shoulders of cavities including cleaning the exposed
concrete surface and reinforcement with wire brushes etc. and
disposal of debris for all lead and lifts all complete as per direction of
Engineer-In-Charge
26.28.1 75mm average thickness sqm 287.10
26.28.2 50mm average thickness sqm 194.60
26.28.3 25 mm average thickness sqm 96.50
26.29 Cleaning of reinforcement from rust from the reinforcing bars to give
it a total rust free steel surface by using alkaline chemical rust
remover of approved make with paint brush and removing loose
particles after 24 hours of its application with wire brush and thoroughly
washing with water and allowing it to dry, all complete as per direction
of Engineer-In-Charge.
26.29.1 Bars upto 12 mm diameter metre 5.90
26.29.2 Bars above 12 mm diameter metre 11.80
26.30 Drilling suitable holes in reinforced or plain cement concrete with
power driven drill machine to a minimum depth of 100mm upto 200mm
in RCC beams, lintels, columns and slabs to introduce steel bars for
sunshades/balconies including fixing the steel bars in position using
epoxy resin anchor grout of approved make but excluding the cost of
reinforcement, all complete as per direction of Engineer-In-Charge.
26.30.1 Upto and including 12mm dia. each 113.05
26.31 Providing, mixing and applying bonding coat of approved adhesive
on chipped portion of RCC as per specifications and direction of
Engineer-In-charge complete in all respect.
26.31.1 SBR Polymer (@10% of cement weight) modified
cementitious bond coat @ 2.2 kg cement per sqm of
surface area mixed with specified proportion of approved
polymer sqm 117.30
26.31.2 Epoxy bonding adhesive having coverage 2.20 sqm/kg
of approved make sqm 388.50
26.32 Providing, mixing and applying SBR polymer (of approved make)
modified Cement mortar in proportion of 1:4 (1 cement: 4 graded
coarse sand with polymer minimum 2% by wt. of cement used) as
per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness
shall be done just after the surface preparation is completed and Payment
under this item shall be made only after proper wet curing has been
done and surface has been satisfactorily evaluated by sounding / tapping
with a blunt metal instrument and/or the 75mm size cube crushing
strength at the end of 28 days to be not less than 30 N/Sqmm2).
26.32.1 12 mm average thickness. sqm 304.10

430
No.
26.32.2 25 mm average thickness in 2 layers. sqm 471.00

26.32.3 50 mm average thickness in 3 layers. sqm 942.00
26.33 Providing, mixing and applying SBR polymer (of approved make @
minimum 2% by wt. of cement used) modified plain/reinforced cement
concrete for structural members having minimum characteristic
compressive strength [with ordinary portland cement, coarse sand
and graded stone aggregate of 10mm maximum size in proportion
as per design criteria] with specified average thickness.
Note: Rates shall be for finished surface area of concrete and shall
include the cost of labour, concrete and appropriate approved Super-
Plasticiser for rendering concrete as flowable and SBR polymer but
shall exclude cost of reinforcement, bond coat, Shear Keys, centering
and shuttering, strutting, propping etc (Payment under this item shall
be made only after proper wet curing has been done and surface has
been satisfactorily evaluated by sounding/tapping with a blunt metal
instrument)
26.33.1 50mm thick in Grade M 25 with cement content not less
than 330 kg per cum sqm 539.90
26.34 Providing and laying SBR Polymer modified (of approved make @
minimum 2% by wt. of cement used) plain/reinforced concrete jacket
for the structural members e.g. columns, pillars, piers, beams etc
with concrete having the specified minimum characteristic
compressive strength [with ordinary portland cement, coarse sand
and graded stone aggregate of 10mm maximum size in proportion
as per design criteria] with specified average thickness all-round
existing core of RCC member.
Note: Rates shall be for finished surface area of concrete and shall
include the cost of making holes in existing RCC slab, if required, for
pouring concrete in shuttering mould of jacket and appropriate
approved Super-Plasticiser for rendering concrete as flowable self
compacting and SBR polymer but shall exclude cost of
reinforcement, bond coat, Shear Keys, centering and shuttering,
strutting, propping etc (Payment under this item shall be made only
after proper wet curing has been done and surface has been
satisfactorily evaluated by sounding/tapping with a blunt metal
instrument)

431
No.
26.35 Providing and injecting approved grout in proportion recommended

by the manufacturer into cracks/honey-comb area of concrete/
masonry by suitable gun/pump at required pressure including cutting
of nipples after curing etc. complete as per directions of Engineer-in-
Charge.
(The payment shall be made on the basis of actual weight of approved
grout injected.)
26.35.1 Stirrer mixed Acrylic Polymer of approved make @ 2%
of weight of cement used) modified Cement slurry made
with non shrink compound in concrete/RCC work kg 97.30
26.35.2 Stirrer mixed SBR Polymer (of approved make) modified
Cement slurry made with Shrinkage Compensating
Cement in concrete/RCC work. kg 101.55
26.35.3 Epoxy injection grout in concrete/RCC work of approved
make kg 792.30
26.36 Providing, erecting, maintaining and removing temporary protective
screens made out of specified fabric with all necessary fixing
arrangement to ensure that it remains in position for the work duration
as required by the Engineer-in-charge.
26.36.1 Wooven PVC cloth sqm 45.50
26.37 Cleaning of exposed concrete surface of sticking material including
loose and foreign material by sand blasting with coarse sand followed
by and including cleaning with oil free air blast as per direction of
Engineer in charge. sqm 289.90
26.38 Shotcreting R.C.C. columns, beams and slabs etc. in layers with
approved design mix concrete having the specified minimum
characteristic compressive strength [with ordinary portland cement,
coarse sand and graded stone aggregate of 10 mm maximum size
in proportion as per design criteria] including the cost of centering
and shuttering at edges and corners etc. as directed by Engineer-
in-Charge
Note: Rates shall include the providing necessary ground wires etc.
The levelling gauges, if used, shall be paid for separately. Payment
under this item shall be made only after proper wet curing has been
done and surface has been satisfactorily evaluated by sounding/
tapping with a blunt metal instrument.
26.39 Providing and inserting 12mm dia galvanised steel injection nipple in
honey comb area and along crack line including drilling of holes of
required diametre (20mm to 30mm) up to depth from 30mm to 80mm

432
No.
at required spacing and making the hole & crack dust free by blowing
compressed air, sealing the distance between injection nipple with
adhesive chemical of approved make and allow it to cure complete
as per direction of Engineer-In-Charge. each 191.20
26.40 Providing and fixing hard drawn steel wire fabric of size 75 x25 mm
mesh or other suitable size wire mesh to be fixed & firmly anchored
to the concrete surface by means of “L” shaped mild steel shear key
welded with existing reinforcement including the cost of materials,
labour, tool & plants as approved by Engineer-in-charge. sqm 801.70
NEW TECHNOLOGY ITEMS
26.41 Designing, providing, installing and fixing factory finished custom
designed cold form Light Gauge Steel Framed super structure
comprising of steel wall panel, trusses, purlins etc manufactured out
of minimum 0.75 mm thick steel sheet as per design requirements.
The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc
Alloy coated steel having minimum yield strength 300-550 Mpa)
conforming to AISI specifications and IBC 2009 for cold formed steel
framing and construction and also as per IS: 875-1987, ISO 800-
1984 and IS:801- 1975. The wind load shall be as per provisions of IS
875 (part -III). LGSFS frame shall be designed as per IS: 801 using
commercially available software such as Frame CAD Pro-11.7/
STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture-2011 or
equivalent. Proper usage of Connection Accessories like Heavy Duty
Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss
with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections,
L-Shaped Angles for better structural stability. The framing section
shall be cold form C-type having minimum web depth 89 mm x 39mm
flange x 11mm lip in required length as per structural design
requirement duly punched with dimple/slot at required locations as
per approved drawings. The slots will be along centre line of webs
and shall be spaced minimum 250mm away from both ends of the
member. The frame can be supplied in panelized or knock down
condition in specific dimensions and fastened with screws extending
through the steel beyond by minimum of three exposed threads. All
self drilling tapping screws for joining the members shall have a Type
II coating in accordance with ASTM B633(13) or equivalent corrosion
protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames
shall be fixed to RCC slab or Tie beam over Neoprene rubber using
self expanding carbon steel anchor bolt of dia as per approved
drawings. design subject to minimum 12mm diameter and 121mm
length conforming to AISI 304 and 316 at 500mm c/c with minimum
embedment of 100mm in RCC (RCC to be paid separately) and located
not more than 300mm from corners or termination of bottom tracks
complete in all respects. The item also includes the submission of
stability reports duly examined and issued by any NIT/IIT. The rate
includes the concept design, detailed design, fabrication of sections,
transportation, installation and all required fixing arrangement at
site as described above. kg 217.50

433
No.
26.42 Providing and fixing of external wall system on Light gauge steel
frame work with . Outer face having 6mm thick heavy duty fiber cement
board fixed on 9mm thick heavy duty fiber cement board confirming
to IS 14862:2000, category IV type A (High pressure steam cured)
as per standard sizes fixed with self-drilling / taping screws / fasteners
@ 60cm c/c of approved make. A grove of 2 mm to 3mm shall be
maintained and groves shall be sealed with silicon based sealant.
The board shall be fixed in a staggered pattern.Screws shall be of
counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of
length varying from 25 to 45 mm and internal face 12.5mm thick
gypsum plaster board fixed on 8mm thick fiber cement board
confirming to IS 14862:2000 of category III type B (High pressure
steam cured) as per standard sizes fixed with self-drilling / taping
screws / fasteners @ 60cm c/c of approved make, proper taping and
jointing to be done using fiber mesh tape and epoxy and acrylic
based jointing compound for seamless finish.(cost of frame work to
be paid for separately). sqm 3418.95
26.43 Providing and fixing internal wall panels on Light gauge steel frame
work with 12.5mm thick gypsum plaster board conforming IS
2095:2011 fixed on 8mm thick fiber cement board conforming to IS
14862:2000 of category III type B (High pressure steam cured) as
per standard sizes fixed with self-drilling / taping screws / fasteners
@ 60cm c/c of approved make, Screws shall be of counter sunk rib
head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying
from 25 to 45 mm. Proper taping and jointing to be done using
fiber mesh tape and epoxy and acrylic based jointing compound for
seamless finish.(cost of frame work to be paid for separately) sqm 2118.95
26.44 Providing and fixing in all exterior face panels breathable vapour barrier
underneath the cement fiber board as per National Building Code
2009 complete as per direction of Engineer-in-charge. sqm 293.95
26.45 Supplying and installation of moisture resistant/fire resistant 6 mm
thick Heavy duty fiber cement board (High pressure steam cured)
conforming to IS 14862:2000 of category III type B as per standard
sizes fixed with self-drilling / taping screws. Screws shall be of counter
sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length
varying from 25 to 45 mm. sqm 1179.30
26.46 Providing and fixing in position, 200 mm thick factory made Expanded
Polystyrene Core (EPS Core) wall panels consisting of EPS core
sandwiched between two Engineered sheets of welded wire fabric
mesh duly finished with shortcrete materials on outer faces. The
fabric mesh shall be made of 3 mm dia G.I. wire mesh with 50 mm
pitch in both the directions and on both faces of the wall, kept at
120-135 mm gap and connected by the zig zag G.I. wire of 3 mm dia
at alternate row by welding (at an angle ranging from 50-70 degree) .
The EPS core shall consist of 100 mm thick EPS of density not less
than 20 kg/ per cum. Both the outer faces of the panel shall be
finished by applying the layer of 50 mm thick cement mortar 1:3 {1
cement: 3 coarse sand (not having more than 40% stone chips of
size upto 6 mm)} À with the help of shotcreting/guniting equipment

434
No.
etc at a pressure not less than 1 bar (100Kn/m2) and both surfaces
finished with trowel. Fixing operations of wall panels shall be completed
in all respect as per drawings and specifications and under the overall
direction of the Engineer-in-charge. sqm 3854.60
26.47 Providing and fixing in position, 230mm thick factory made Expanded
Polystyrene Core (EPS Core) roof/floor panels made of 3 mm dia
G.I. wire mesh with 50 mm pitch in both the directions and on both
faces of panel, kept at 120-135 mm gap and connected by the zig
zag G.I. wire of 3 mm dia at alternate row by welding (at an angle
ranging from 50-70 degree). The EPS core shall consist of 100 mm
thick EPS of density not less than 20kg/ per cum. The bottom side
of the panel shall be finished by applying a layer of 60-65 mm thick
cement mortar 1: 3 {1 cement: 3 coarse sand (not having more than
40% stone chips of size upto 6 mm)} À with the help of shotcreting
equipment etc at a pressure of not less than 1 bar (100Kn/m2) and
surface finished with trowel. The top face of the panel shall be provided
and finished by applying 70-75 mm thick layer of cement concrete
1:1.5: 3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20
mm nominal size). Fixing operations of roof/floor panels
shall be completed in all respect as per drawings and specifications
and under the overall direction of the Engineer-in-charge. sqm 4144.95
26.48 Providing and fixing of customized aluminium formwork for monolithic
construction RCC members with a repetitive usage of 100 times
using grade 5052 aluminium of panel sheets of minimum 4 mm thick
and grade 6061 (Type-6) aluminium for extruded sections. The form
work includes of beam components i.e. beam side panel, prop head
for soffit beam, beams soffit panel, beam soffit bulk head and deck
components i.e. deck panel, deck prop, prop length, deck mid, soffit
length, deck beam bar and wall components i.e. wall panel, rocker,
kiker and internal soffit corner, external soffit corner, external corner,
internal corner etc. The panels are held in position by a simple pin
and wedge system that passes through holes in the out side rib of
each panel. The tolerance of finished panels to be (-1 mm), and shall
conform to IS 14687-1999. Pins and wedges to be
made of high grade mild steel, all complete as per direction of
Engineer-in- charge. (Cost of RCC work shall be paid separately)
26.49 Providing and fixing in position factory made EPS cement
sandwich wall/roof/floor light weight solid core panels made
of core material of EPS granule balls/beads (conforming to IS
4671:1984 and shall have density not less than 15kg per cum)
adhesive, cement, sand, flyash and other bonding material in
mortar state processed to form in a preset mould. The outer
face on both sides of the panels will be non asbestos fiber
cement board confirming to IS 14862:2000 or Calcium silicate
board confirming to EN 14306:2009 of 5mm thick each. Panel
shall be laid on 6mm thick cement mortar (1 cement: 2 fine
sand) mixed with chemical adhesive of 0.5kg per 50kg of
cement or shall be preferably fixed into ‘C’ channel made of
1.2mm thick MS plate screwed/fastenened to the slab/column/
beam etc. The panel shall fixed vertically with tongue and
groove joint and horizontally locked with steel bar between
each other and floors and filled with cement mortar and
adhesive. Panels should be used as floor & roofing with
additional structural support, steel or RCC depending upon
the design. All the operation shall be completed in all respect
as per drawings, Manufacturers specifications and under the
overall direction of Engineer-in-Charge (Cost of all the material
is included except “C channel” which will be paid seperately).
435
No.
26.49.1 Non load bearing panels 50mm thick of required size sqm 1166.85
26.50 Providing and fixing in position factory made non asbestos
fibre reinforced aerated cement sandwich wall/roof/floor light
weight solid core panels made of light weight cement concrete
core composed of OPC cement, pulverized flyash, quick lime,
cotton pulp & Gypsum in mortar state mixed with aeration
agent in a preset mould. The outer face on both sides of the
panels will be non asbestos fibre cement board confirming to
IS 14862:2000. These solid wall panels are installed using
Galvanized iron steel tracks/C channel of 1mm thick of required
sizes as recommended by manufacturer’s and fixed to floor
and RCC soffit in plumb to each other with steel screw/
fasteners. The panel shall be fixed vertically with tongue &
groove joint with cement based polymer modified jointing
compound. The exposed surface finished with fibre mesh/glass
fibre tape with polymer based jointing compound having
superior flexibility. Panels should be used as floor & roofing
with additional structural support, steel or RCC depending upon
the design. All the operation shall be completed in all respect
as per drawings, Manufacturers specifications and under the
overall direction of Engineer-in-Charge (Cost of all the material
is included except “tracks/C channel” which will be paid
separately).
26.50.1 Non load bearing panels 50mm thick of required size
(minimum 4mm thick fibre cement board) sqm 1317.95
26.50.2 Non load bearing panels 75mm thick of required size
(minimum 5mm thick fibre cement board) sqm 1535.70
26.51 Supplying of standard quality GFRG panel of 124 mm thickness
with modular cavities purchased from GFRG panel
manufacturing plant in the country, cut to required wall sizes
and floor/ roof slab sizes in correct length and height, including
cutting of door, window and ventilator opening as per the
cutting drawing prepared by architects /design engineers for
the construction of GFRG building and loaded in stillages for
transportation to the construction site. Cost of panel includes
security deposits, hire charges of stillages & jaws, cost of
transportation in trucks/ lorries without any damages upto
300kms including all leads and lifts from GFRG manufacturing
plant to construction site and unloading at site using suitable
fork lift/ crane. (Payment shall be made on the basis of area of
one side of panel without reduction of opening of door/
window / ventilator).
For transportation above 300kms, additional charges to be paid. sqm 1305.60

436
No.
26.52 Erection of GFRG Panels in walls in all floors using suitable

crane as per instructions of Engineer-in-Charge, as per cutting
drawings and structural drawings, in perfect line and plumb,
above RCC plinth beam/GFRG panel below and provide
necessary lateral/ slanting support to keep the wall panel in
safe position, providing & tieing of Reinforcement as per
structural drawings and applying a coat of water repellant
coating Zycosil/equivalent or equivalent product (1 Zycosil/
equivalent compound :10 water ) to saturation level over RCC
plinth beam to provide water proofing treatment to joint
between wall panel & plinth beam as per the guide lines /
instruction by the engineer in charge. (Cost of reinforcement,
water proofing of walls and plinth beam/GFRG panel below
joints and installation of door/ window frames before filling of
concrete shall be paid separately). The rate quoted shall
include making provision for laying of lintels, beams,
sunshades, staircase beams, lofts, plumbing work, electrical
conduits and any structural insertion etc., as per the drawing
and direction of the engineer in charge. The payment shall be
made based on the actual exposed area (one side only) of the
panel.The work shall be carried out as per the Special
Conditions For Glass Fibre Reinforced Gypsum (GFRG)
Structures mentioned in NIT.Note: i) When cutting panel, “A”
side is to be for outside or external surface of respective
external wall and B side is to be for internal surface of wall
ii)Erection of panel is to be with reference to both building
plan & cutting drawing by following notational mark indicated
in the cutting drawing as well as notional mark written on
each panel cut as per cutting drawing sqm 266.55
26.53 Filling of empty cavities (as shown in the structural design
drawing) with quarry dust mixed with 5% cement (by volume).
After initial infill of 50 mm thick with M25 concrete at base/
bottom of cavities to seal off, infill wall panel cavities in 3 stages
as detailed below, (i) 1st pour / infill to be limited to 0.3 to 0.50
m height from bottom of the panel.(ii) 2nd Pour/ infill: infilling
shall be done only after 90 minutes interval between successive
pours. The maximum height of infill shall be restricted to 1.5m
height or up to the top level of door / window.(iii) 3rd pour/infill:
After an interval of 90 minutes of second pour, infill or pour the
balance height up to the bottom of embedded RCC tie beam.
Pour enough water just required to dampen the dry mix enough
to form cake form after each stage.(cost of laying M25 concrete
shall be paid separately)(If any rain falls in between any stages
of concrete pour, make sure to cover the panel top to prevent
ingress of water or water falling into the cavities. In case of
water collection over the concrete inside the panel, drill 10mm
hole in GFRG panel immediately above concrete filled level to
drain out water before pour/in-fill of balance concreting) cum 2346.15
26.54 Laying of GFRG panel as roof / floor slab panel and staircase
panel using suitable crane as per instructions of Engineer-in-

437
No.
Charge, including providing support system with 25mm x

300mm-400 mm wide plywood, as runner with proper prop
below proposed micro beams including
(a) Cutting of top flange of panel to 180 mm wide (leaving 25mm
projection on either side) to provide RCC embedded micro
beam as per cutting drawings and structural drawings.
(b) Reinforcement for micro beams and tie beams to be provided
in position with proper anchorage as per structural drawings.
(c) Provision for Electrical cabling, fan hooks and laying of
pipes for plumbing work.
(d) Concreting of Tie beam, micro beam and top of GFRG
panels (50 mm thick) with M-25 cement concrete mix
using coarse aggregate of size less than 20 mm including
laying of 10 gauge 100x100 size weld mesh with 25 mm
effective cover from the panel top. sqm 285.15
26.55 Supplying and fixing 10 Gauge weld mesh of size 100mm x100
mm for floor/roof slab concrete screed over the micro beams as
reinforcement. The weld mesh shall be fixed as per drawing. sqm 233.70
26.56 Application of ZMB 60/equivalent solution (100 Kg ZMB 60/
equivalent, 1 litre ZMB Nano Thinner, 20 litre water & 1 Litre
Zycoprime/equivalent = 122 litre/kg) over already applied coat
of Zycosil/equivalent & Zycoprime/equivalent solution on the
top of all the RCC plinth beams by brush/spray coat before
erection of GFRG over RCC plinth beams in GF. In the case of
upper floors 150 mm wide on floor slab for all the external
walls, bath/toilet/wet areas (3 hrs drying time) before erection
of wall panel on upper floors including erection of parapet wall. sqm 286.00
26.57 After erection of GFRG wall panels, seal all GFRG wall joints
with paper tape temporarily. Water proofing treatment of
vertical joints with Zycosil/equivalent water proofing Solution
(1 litre of Zycosil/equivalent & 20 litres of water stirred first & 2
litres of Zycoprime/equivalent added and stirred (total 23 litres))
with 50 ml syringe till the gap and in filled concrete is
completely saturated. After removing the paper seal, seal
off the vertical joints with water proofing material “Grout RW/
equivalent “ (Sealing cost excluded.) metre 81.25
26.58 Filling of joints between RCC plinth beam / floor slab and wall
panel of external walls, toilet / bath room / wet areas walls on
all floor and parapet wall over roof slab, stair case head room
at the time of erection of GFRG panels with Grout RW/
equivalent sealant compound after the erection of panel before
the infill of concrete in panel cavities and fine finish. This
applies for all horizontal and vertical joints between GFRG
wall and slab panels. metre 39.60
26.59 Water proofing treatment of Vertical joints (of external side
and internal side) between door frame, window & ventilator
frames (on all four sides) of outer wall over the Zycosil/
equivalent & Zycoprime/equivalent solution already applied
(before the installation of door / window / ventilator frames in
position) and fine finish with Grout RW/equivalent. metre 40.40

438
No.
26.60 Water proofing treatment of RCC sunshade with Zycosil/

equivalent water proofing Solution (1 litre of Zycosil/equivalent
& 20 litres of water stirred first & 2 litres of Zycoprime/equivalent
added and stirred (total 23 litres)) till it meets the saturation
level and testing as per RILEM or by water drops test in which
water drops do not absorb but drops remain or rolls. sqm 131.50
26.61 In-filling / sealing of joint between RCC lintel cum sunshade
and wall (on external side) in all floors by pushing in Grout
RW/equivalent in paste form and coving 20 mm x 20 mm after
applying a coat of Zycosil/equivalent & zycoprime/equivalent
solution before cement plastering of top, bottom and sides of
RCC sunshade. metre 40.40
26.62 Designing, Providing, installing and fixing factory finished
customed design pregalvanized high tensile steel joists
manufactured from G350 Z275 confirming to IS:277-1992,
minimum coating of galvanizing 275 gm/sqm, minimum yield
stress 35 MPa & minimum tensile strength of 380 MPa
placed 1.23 metre apart to support the load of slab etc as per the
design & directions of Engineer-in-Charge. kg 139.65
26.63 Providing and fixing special adjustable lockbars of mild steel
E-250 to support the temporary plywood for work between joists
during construction as per design & directions of the Engineer-
in-charge. kg 20.55
26.64 Centering and shuttering with 12mm thick shuttering plywood
confirming to IS 4990:2011 and removal of form at all heights.
Plywood will be supported on lock bars.
26.64.1 Suspended floors, roofs, landings, balconies and
access platform. sqm 87.95
26.65 Providing and fixing roofing consist of 0.8 mm thick galvanized
steel deck sheet confirming to IS 277:1992 used as permanent
shuttering over which MS wire mesh 3mm laid at 100x100 mm
grid including edge trim covered with concrete. This metal
deck will be supported on structural steel beam with shear
studs. (Structural steel like Beam, column, joists etc. & concrete
of different grade as per design will be paid separately). sqm 1451.70
26.66 Providing and fixing in position, 130 mm thick factory made
Expanded Polystyrene Core (EPS Core) wall panels consisting
of EPS core sandwiched between two Engineered sheets of
welded wire fabric mesh duly finished with shortcrete materials
on outer faces. The fabric mesh shall be made of 3 mm dia
zinc coated G.I. wire mesh with 50 mm pitch in both the
directions and on both faces of the wall and connected by GI
wire of 3mm dia at alternate row by welding. The EPS core
shall consist of 60 mm thick EPS of density not less than 16 kg/
per cum. Both the outer faces of the panel shall be finished by
applying the layer of 35 mm thick cement mortar 1:3 {1 cement:
3 coarse sand (not having more than 40% stone chips of size
upto 6 mm)} with the help of shotcreting/guniting equipment

439
No.
etc at a pressure not less than 1 bar (100KN/m2) and both

surfaces finished with trowel. Fixing operations of wall
panels shall be completed in all respect as per drawings and
specifications and under the overall direction of the Engineer-
26.67 Providing and fixing of external thermal insulation and
composite system with First layer of self-extinguishing type
Expanded Polystyrene (EPS) insulation boards of 120 mm thick
( max 1mX0.5m section), confirming to IS 4671:1984, having
thermal conductivity of 0.034 W/mK, (measured as per IS 3346-
1980), density of 20-24 kg/m³ measured as per IS 5688-1982,
Fire retardant property self-extinguishing type as per EN 13501-
1, bonded with special polymer modified cementitious
adhesive confirming to EOTA ETAG 004 (European Technical
Approval) formulated to bond polystyrene insulation boards
to typical mineral substrate (according to ETAG 004) and
Polypropylene mechanical fasteners with plastic pin
confirming to EOTA ETAG 014 (European Technical Approval)
having dia 10mm & L=200mm on finished level wall and the
junction between two adjacent EPS boards to be sealed with
low expansion moisture cure Polyurethane Foam. Second
layer consists of Fiberglass mesh covered with alkali-resistant
coating, mass per unit area > 145 gm/m2, mesh size: 3.9x4.0
mm ±10% embedded in special polymer modified cementitious
Base Coat with hydrophobes and the corners will be protected
with Corner-beads with alkali-resistant mesh wings at least 10
cm wide, mesh mass per unit area min 145 gm/m2. The surface
will be levelled, finished, made smooth complete in all respect
as per manufactures specification and as per directions of
Engineer-in-Charge. sqm 3366.60
26.68 Providing and laying factory made Precast concrete solid blocks
of 200 mm thickness of grade M10 made of C&D waste from
approved manufacturer in foundation and plinth in:
26.69 Providing and laying factory made Precast concrete solid blocks
of 200 mm thickness of grade M10 made of C&D waste from
approved manufacturer in superstructure above plinth level
up to floor V level
26.70 Providing and laying half block masonry with factory made
Precast concrete solid blocks of 100 mm thickness of grade
M10 made of C&D waste from approved manufacturer in
foundation and plinth in:
26.70.1 Cement mortar 1:4(1 cement : 4 coarse sand) sqm 695.40
Precast concrete solid blocks of 100 mm thickness of grade
M10 made of C&D waste from approved manufacturer in
superstructure above plinth level up to floor V level:
26.71.1 Cement mortar 1:4 (1 cement : 4 coarse sand) sqm 853.75

440
No.
26.72 Providing and laying 60mm thick factory made cement concrete
paver block of approved shape and colour of M -30 grade made
of C&D waste by block making machine with vibratory
compaction laid in required pattern and including over 50mm
thick compacted bed of coarse sand, filling the joints with fine
sand etc. all complete as per the direction of Engineer-in-
charge. sqm 748.60
PREFAB/PRECAST TECHNOLOGY
26.73 Fabrication & Manufacturing of Prestressed Hollow Core slab
(Hollow area 25 to 30%) of different thickness & modular width
1200 mm in Controlled Factory Environment with approved
methodology informing to IS 10297- 1982 conforming to IS : 10297-
1982 by using long line casting method having arrangement of
proper steel bed. Concreting should be done by batch mixing
plant capable of producing zero slump concrete, transported
through automatic shuttels of standard make & layed on bed
with the help of extruder/Slipformer, finishing, curing and also
provision of steam curing. Cutting, making necessary cutout/holes
of required sizes for services in slab element after achieving
required strength, yard handling & stacking all complete as per
approved shop drawings & design mix as per the direction of the
Engineer-in-charge. (Cost of strands should be paid separately).
Note : Excess/ less cement over the specified cement content
used as per design mix is payable / recoverable separately.
26.73.1 Concrete Grade-M-40 (cement content 400 kg )
26.73.1.1 100 mm thick hollow core slab metre 1152.35
26.73.2 Extra for using M-50 (Cement content 425 kg) instead
of M-40
26.73.2.1 100mm thick hollow core slab metre 17.30
441
No.
of M-40
26.74 Fabrication and manufacturing of solid precast concrete
element with provisions of shear keys, connecting loops, dowel
tubes and proper lifting accessories for walls, beams, slabs,
stairs, column etc, of various thickness, shape and size of
different concrete grades manufactured in controlled factory
environment with approved methodology including moulds
(Pallet system, Tilts form, table moulds, battery moulds, vertical
moulds, beam moulds, column moulds, staircase moulds,
Facade mould, etc.), mixing, transporting and placing of
concrete, vibrating, curing, finishing, making necessary cutout/
holes of required sizes for services, yard handling & stacking
all complete as per IS 11447:1985 and as per approved shop
drawings and design mix as per the direction of Engineer-in-
Charge (Cost of reinforcement, Mechanical, Electrical and
Plumbing inserts will be paid separately).
26.74.1 Concrete grade M-35 (Cement content 370 kgs) cum 14554.65
of M-35 cum 230.90
of M-35 cum 423.30
of M-35 cum 538.75
26.75 Providing & laying in position Prestressing steel strands (low
relaxation) on hollow core bed by using mechanical pulling
arrangement like Rabbit/ Bed master including all accessories
for Stressing & destressing operations as per approved make
conforming to IS1343 & grade FY-1860 etc, complete as per
drawings and direction of Engineer -in-charge. kg 144.55
26.76 Transportation of Precast Elements by flat bed Trailor (Double
/ Triple axle 40ft Length with proper accessories like A frame
etc) from factory, including the cost of loading , unloading &
stacking at site with the help of required capacity cranes.
26.76.1 Lead within 15km MT 444.05
26.76.2 Add/Deduct over item 26.76.1 for every additional
lead of 5 km MT 97.20

442
No.
26.77 Erection & Installation of Precast/Prestressed Concrete

elements in correct & final position with proper line level and
plumb at site making all arrangements (i.e cranes, push-pull
jacks & all another T & P for lifting Placing & Alignment of
elements, within erection tolerance as per IS 15916 as per
approved shop drawings and all complete as per the direction
of Engineer-in-Charge but excluding the cost of sim pads, non
shrink grout and steel works i.e hangers. All work up to fifth
floor.
26.77.1 Prestressed hollow core Slab up to 200 mm thickness sqm 160.85
26.77.2 Prestressed hollow core slab above 200 mm up to
400 mm thickness sqm 277.15
26.77.3 Solid concrete wall elements cum 2147.55
26.78 Providing & Applying weather proof sealant on outer joints of
approved make confirming to IS & directed by Engineer-in-
charge.
26.78.1 Sealant 25mmx10mm at joints metre 137.00
26.79 Providing & Laying of levelling sim pads required sizes (5x5cm
to 10x10cm) of PVC / Rubber to adjust level of bearing surface
of supporting members as per the direction of Engineer in
charge.
26.79.1 2mm thick each 23.65
26.79.2 5 mm thick each 30.35
26.79.3 10 mm thick each 43.70
26.80 Providing & Grouting of dowel tubes / Shear keys / Joints of
precast members with M-60 grade cementitious grout (Non
Shrink) of approved make by suitable means ( Free flowing /
pump),curing etc. Complete as per directions of Engineer-in-
charge. (The payment shall be made on the basis of actual
weight of approved grout injected.)
26.80.1 Stirrer mixed cementitious grout (non shrink) of approved
make in dowel tubes / Shear keys / Joints of precast
members. kg 74.25
26.81 Providing and fixing Scaffolding net of required width made
of high density Polyethylene UV stabilized knitted on warp
knitting machines having density 100gm/sqm and shading
coefficient minimum 75% around the construction site/ for
vertical extension as per requirement including fastening/tying
with building/scaffolding pipes or with any other fixtures etc.
complete as per direction of Engineer-in-Charge. (One time
payment shall be made for providing Scaffolding net from start
of work till completion of work including shifting if any.
The Scaffolding net shall be the property of the contractor on
completion of the work) sqm 24.20

443
COEFFICIENTS
FOR CEMENT
CONSUMPTION
444
1.0 COEFFICIENTS FOR CEMENT CONSUMPTION
3.0 MORTAR
Code Description Unit Quantity of cement
No. per unit quantity of
work (Quintals)
3.1 Cement Mortar 1:1 (1 cement : 1 fine sand). cum 10.20

3.2 Cement mortar 1:2 (1 cement : 2 fine sand). cum 6.80
3.7 Cement mortar 1:2 (1 cement : 2 coarse sand). cum 6.80
3.12 Cement mortar 1:2 (1 cement : 2 stone dust). cum 6.80
3.13 Cement mortar 1:2 (1 cement : 2 marble dust). cum 6.80
3.15 White cement mortar 1:2 (1 white cement : 2 marble dust). cum 6.80*
* white cement
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 3.0 MORTAR
445
4.0 CONCRETE WORK
work (Quintals)
CEMENT CONCRETE (CAST - IN- SITU)

4.1 P/L cement concrete - all works upto plinth level :
4.1.2 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded
stone aggregate 20 mm nominal size) cum 4.00
4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) cum 3.20
4.1.4 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone
4.1.11 1:5:10 (1 cement : 5 fine sand : 10 graded stone
4.1.12 1:2:3½:9 (1 ordinary portland cement : 2 Fly ash :
3½ coarse sand : 9 graded stone aggregate 40 mm
nominal size) cum 1.70
4.1.13 1:2½:4:11 (1 ordinary portland cement : 2½ fly ash :
4 coarse sand : 11 graded stone aggregate 40 mm
nominal size) cum 1.30
4.2 P/L cement concrete in retaining walls, return walls etc.
4.2.2 1:1½:3 (1 cement:1½ coarse sand:3 graded stone
4.4 P/L cement concrete in kerbs, steps etc.:
4.4.1 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size) cum 4.00
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 4.0 CONCRETE WORK
446
work (Quintals)
CEMENT CONCRETE (PRE-CAST)

4.5 P/L precast cement concrete string or lacing courses,
copings etc.:
4.5.1 1:1½:3 (1 cement:1½ coarse sand:3 graded stone
4.6 P/L precast cement concrete in kerbs, edgings etc.:
4.6.1 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone
4.7 P/L precast cement concrete solid blocks:
4.7.1 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone
4.8 P/L precast cement concrete hollow blocks:
4.9 Precasting and placing in position 125 mm dia Bollards
600 mm high. each 0.097
DAMP- PROOF COURSE
4.10 P/L D.P.C. 40 mm thick with C.C. (1:2:4). sqm 0.13
4.11 P/L D.P.C. 50 mm thick with C.C. (1:2:4) sqm 0.16
MISCELLANEOUS
4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 sqm 0.11
4.19 P/L Ready mixed concrete using flyash:
4.19.1 All works upto plinth level
4.19.1.1 M-15 grade plain cement concrete cum 2.40
4.19.2 All works above plinth and upto floor V level
4.20 P/L ready mix plain cement concrete
4.20.1 All works upto plinth level
4.20.2 All works above plinth and upto floor V level
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 4.0 CONCRETE WORK
447
5.0 REINFORCED CEMENT CONCRETE
work (Quintals)
CAST-IN-SITU
5.1 P/L R.C.C. upto plinth level :
5.2 R.C.C work in walls etc.:
aggregate 20 mm nominal size cum 4.00
5.3 R.C.C. (1:1.5:3) work in beams etc. cum 4.00
5.4 R.C.C. (1:1.5:3) work in kerbs, steps etc. cum 4.00
5.5 R.C.C. (1:1.5:3) work in arches,domes etc. cum 4.00
5.6 R.C.C. (1:1.5:3) work in chimneys & shafts. cum 4.00
5.7 R.C.C. (1:1.5:3) work in well-steining. cum 4.00
5.8 R.C.C. (1:1.5:3) work in vertical and horizontal fins individually
or forming box louvers, facias and eaves boards. cum 4.00
PRE - CAST R.C.C.
5.12 P/F precast R.C.C. (1:1.5:3) work in string courses, bands,
copings, bed plates, anchor blocks, plain window sills etc. cum 4.00
5.13 P/F precast R.C.C. (1:1.5:3) in small lintels not exceeding
1.5m clear span. cum 4.00
5.14 P/F precast R.C.C. (1:1.5:3) in mouldings as in cornices,
windows sills etc. cum 4.00
5.15 P/F precast R.C.C. (1:1.5:3) in lintels, beams and bressumers
etc. cum 4.00
5.16 P/F precast R.C.C. (1:1.5:3) in shelves. cum 4.05
5.17 P/F precast R.C.C. (1:1.5:3) in vertical & horizontal fins
individually or forming box louvers. cum 4.00
5.18 Fixing precast cement concrete Jali (1:2:4).
5.18.1 50 mm thick 100 sqm 1.64*
5.18.2 40 mm thick 100 sqm 1.64*
5.18.3 25 mm thick 100 sqm 1.64*
* Cement for fixing only.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 5.0 REINFORCED CONCRETE WORK
448
work (Quintals)
ENCASING ROLLED STEEL SECTION

5.19 Encasing rolled steel sections, in beams and columns, with
cement concrete (1:1.5:3). cum 4.00
5.20 Encasing rolled steel section in grillages with cement concrete
(1:1.5:3). cum 4.00
MISCELLANEOUS
5.23 Smooth finishing of exposed surface of R.C.C. work with 6 mm
thick cement mortar (1:3). 100 sqm 3.67
5.24 Rendering smooth the top of suspended floors, landings and
staircases with cement mortar (1:2). 100 sqm 4.17
5.27 Providing and filling in position bitumen mix filler. cum 0.032
DESIGN MIX CONCRETE
5.33 P/L Design mix concrete (M-25). cum 3.30*
5.34 Extra for providing richer mixes at all floor levels :
5.34.1 Providing M-30 grade concrete instead of M-25 grade
B.M.C/ R.M.C. cum 0.10*
B.M.C./ R.M.C. cum 0.20*
B.M.C./ R.M.C. cum 0.30*
5.36 P/F precast R.C.C. in waffle units. cum 4.16*
5.37 P/L RMC manufactured in fully automatic batching plant M-25
grade R.C.C. cum 3.30*
5.40 P/L design mix cement concrete M-25 using Fly ash. cum 3.30*
* Actual weight for design mix will be worked out taking
into consideration the cement requirement as per
particular mix design
5.47.1 P/F factory made precast RCC M-40 doors & windows metre 0.049
5.48 Providing and laying RCC for construction of piers abutments
portal frames etc. cum 4.80
5.49 Constructing cast insitu RCC diaphram wall by providing ….. cum. 4.14
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 5.0 REINFORCED CONCRETE WORK
449
6.0 MASONRY WORK
work (Quintals)
6.1 Brick work in foundation & plinth with non modular bricks.
6.2 Brick work in foundation & plinth with modular bricks.
6.3 Brick work with machine moulded perforated bricks.
6.3.1 With non modular bricks. cum 0.625
6.3.2 With modular bricks. cum 0.55
6.4 Brick work in superstructure
6.7 Half brick masonry in cement mortar (1:3) for closing cavity
5 to 7.5 cm wide in cavity wall. 100 metre 3.86
6.8 Brick work 7 cm in cement mortar (1:3). 100 sqm 9.23
6.9 & Brick work in plain & gauged arches in cement
6.10 mortar (1:3). cum 1.28
HALF BRICK MASONRY
6.12 & Half brick masonry in foundations & plinth and superstructure.
6.13
6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) 100 sqm 14.28
&
6.13.1
6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) 100 sqm 10.64
&
6.13.2
BRICK TILE WORK
6.16 Tile brick masonry in foundation and plinth. :
6.17 & Tile brick masonry with m/c moulded tiles in cement mortar
6.18 1:6 (1 cement : 6 coarse sand). cum 1.00
6.20 & Tile brick masonry with tile bricks in plain/gauged arches
6.21 work in in cement mortar (1:4). cum 1.33
6.22 Tile brick masonry work 5 cm thick in cement mortar (1:3). 100 sqm 7.65
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 6.0 MASONRY WORK
450
work (Quintals)
HONEY COMB WORK

6.23 Honey-comb brick work 10/11.4 cm thick in cement mortar 1:4. 100 sqm 6.56
EXPOSED BRICK WORK
6.26 Brick work with selected bricks in cement mortar (1:6). cum 0.625
6.27 Brick work with modular bricks in cement mortar (1:6). cum 0.55
6.28 Brick work with machine moulded modular bricks in cement
mortar (1:6). cum 0.55
6.29 Brick work with m/c moulded F.P.S. bricks in cement
mortar (1:6). cum 0.625
6.30 Brick work with machine moulded perforated F.P.S. bricks in
cement mortar (1:6). cum 0.625
6.31 Brick work with machine moulded perforated modular bricks in
cement mortar (1:6). cum 0.55
6.32 Brick work with clay flyash F.P.S. brick
6.34 Brick work with non modular fly ash bricks in
6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) cum 0.625
6.35 Brick work with modular calcium silicate bricks machine
moulded in
6.36 Brick work with modular extruded burnt fly ash clay sewer
bricks in :
6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) cum 0.836
6.37 Brick work with modular extruded burnt fly ash clay sewer
bricks in cement mortar (1:3). cum 1.275
6.38 Autoclaved aerated cement blocks masonry with 100mm
thick AAC blocks in cement mortar (1:4). cum 0.57
6.44 Brick edging 7 cm wide in cement mortar (1:4). 100 metre 0.137
6.45 Half brick masonry with non modular fly ash bricks.
6.45.1 Cement mortar 1:3 (1 cement :3 coarse sand). 100 sqm 14.28
6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand). 100 sqm 10.64
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 6.0 MASONRY WORK
451
7.0 STONE WORK
work (Quintals)
RANDOM RUBBLE MASONRY

7.1 & 7.2 Random rubble masonry with cement mortar (1:6). cum 0.825
COURSED RUBBLE MASONRY
7.6 Coursed rubble masonry (first sort) with :
7.7 Coursed rubble masonry (second sort) with :
ASHLAR MASONRY
7.12 Stone work in plain ashlar in cement mortar (1:6) including
pointing with white cement mortar (1:2). cum 0.54
7.13 & Stone work plain ashlar in arches/domes in cement
7.14 mortar (1:3) including pointing with white cement mortar (1:2). cum 1.07
7.15 Stone work ashlar punched in cement mortar 1:6) including
pointing with white cement mortar (1:2). cum 0.54
SUNK, MOULDED, CARVED ASHLAR MASONRY
7.20 Stone work sunk and / or moulded including pointing with
white cement mortar (1:2). cum 0.54
MISCELLANEOUS STONE WORK
7.26 P/F stone dowels 10x5x2.50 cm in cement mortar (1:2) . each 0.007
7.28 P/F sloping chajja of stone 40 mm thick and upto 80 cm wide
in cement mortar (1:4) i/c pointing in white cement mortar (1:2). 100 sqm 5.59
7.29 P/F horizontal chajja of stone 40 mm thick and upto 80 cm
projection in cement mortar (1:4) i/c pointing in white cement
mortar (1:2). 100 sqm 4.94 + 0.03*
7.30 P/F 30 mm red sand stone sun-shade with cement mortar
1:4 including finishing complete. 100 sqm 2.19
7.31 Providing and fixing red sand stone brackets 55x22.5x45cm. 100nos 3.02
7.32 Stone work, plain in copings, cornices, string courses etc.
in Cement mortar 1:6 including pointing with white cement
mortar (1:2). cum 0.54
7.38 Stone tile work for wall lining with 12 mm thick bed in
cement mortar (1:3). sqm 10.44 + 1.70*
* White cement
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 7.0 STONE WORK
452
8.0 CLADDING WORK
work (Quintals)
8.1 Marble work 18 mm thick for wall lining in cement mortar 1:3
including pointing with white cement mortar 1:2. 100 sqm 8.16 + 1.63*
8.2 P/F 18mm thick gang saw cut mirror polished premoulded and
prepolished) machine cut for kitchen platforms, vanity counters
etc. laid over 20mm thick base cement mortar 1:4. 100 sqm 9.12
8.4 Extra for fixing marble /granite stone over and above corres-
ponding basic item, in facia and drops of width upto 150 mm
with epoxy resin based adhesive including cleaning etc.
complete. 100 metre 1.27
8.7 P/F cramps in RCC/ CC backing with cement mortar 1:2 .
8.7.1 Gunmetal cramps kg 0.0635
8.7.2 Stainless steel cramps kg 0.0701
8.9 Stone tile work for wall lining over 12mm thick bed of cement
mortar (1:3) and cement slurry @ 3.3 kg/sqm including
pointing in white cement complete. 100 sqm 10.44 + 1.90*
8.11 P/F machine cut mirror/edge polished 100 sqm. 8.16 + 3.30*
8.14 Stone work (machine cut edges) for wall lining etc. (veneer
work) in cement mortar (1:3) including pointing in white
cement mortar (1:2). 100 sqm 9.18 + 1.56*
8.15 P/F stainless steel cramps in stone wall lining in cement
mortar (1:2). kg 0.07
8.16 P/F copper pins 7.5 cm long 6 mm diameter in stone wall
lining in cement mortar (1:2). each 0.007
8.17 Wall lining butch work with Dholpur stone 40 mm thick,
in cement mortar (1:3) including ruled pointing in cement
mortar (1:2). 100 sqm 15.50 +1.70*
8.18 Stone work ( machine cut edges) for wall lining with grout
of 12 mm thick in cement mortar (1:3) and jointed with
Cement mortar (1:2). 100 sqm 13.744
8.21 P/F structural steel frame (for dry stone cladding) embedded
in brick wall with cement concrete block (1:2:4) 100kg 1.05
8.23 P/F 50x50x50 mm 2nd class teak wood plugs in cement
mortar 1:3. 100 nos. 0.01
8.25 P/F 2nd class teak wood plain lining with wooden plugs 100 sqm 0.055
8.31 P/F 1st quality ceramic glazed wall tiles over 12 mm thick
bed of cement Mortar (1:3) with grey cement slurry @
3.3 kg/ sqm sqm 0.1044
* White cement
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 8.0 CLADDING WORK
453
9.0 WOOD AND P.V.C. WORK
work (Quintals)
MISCELLANEOUS - WOOD WORK
9.46 P/F curtain rods of 1.25mm thick chromium plated brass

brackets with wooden plugs, etc. 100 metre 0.01
9.47 Providing and fixing nickel plated M.S. pipe curtain rods
with nickel plated brackets. 100 metre 0.01
9.53 Providing 40x5 mm flat iron hold fast 40 cm long with cement
concrete block 30x10x15cm 1:3:6 mix. 100 nos 1.10 100 nos 1.10
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 9.0 WOOD AND PVC WORK
454
10.0 STEEL WORK
work (Quintals)
10.4 P/F 1 mm thick M.S. sheet sliding-shutters with frame. 100 sqm 0.35
10.5 P/F 1 mm thick M.S. sheet door with frame. 100 sqm 0.35
10.6 Supplying and fixing rolling shutters. 100 sqm 0.35
10.10.1 & Fixing standard steel glaze door windows etc. 100 kg 0.13
10.11.1
10.13.1 P/F ‘T’ iron froms for doors windows & ventilators 100 kg 0.11
10.15 Providing and fixing M.S. Tubular frames for doors,
windows, ventilators and cupboard with 15x3 mm lugs
10 cm long embedded in cement concrete blocks
15x10x10 cm of 1:3:6 mix. 100 kg 0.28
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 10.0 STEEL WORK
455
11.0 FLOORING
work (Quintals)
11.1 Brick on edge flooring.
11.1.1 1:4 (1 cement : 4 coarse sand) sqm 0.1850
11.1.2 1:6 (1cement : 6 coarse sand) sqm 0.1285
11.3 Cement concrete flooring 1:2:4.
11.3.1 40mm thick with 20mm nominal size stone aggregate sqm 0.17
11.4 52 mm thick cement concrete flooring. sqm 0.231
11.5 62 mm thick cement concrete flooring. sqm 0.263
11.6 Cement plaster skirting with cement mortar (1:3). sqm 0.14
11.7 Cement concrete pavement with C.C. (1:2:4). cum 3.20
TERRAZO FLOORING
11.9 40 mm thick marble chips flooring with under layer 34 mm
thick cement concrete (1:2:4).
11.9.1 Dark shade pigment with ordinary cement sqm 0.1695
11.9.2 Light shade pigment with white cement sqm 0.129+0.0405*
11.9.3 Medium shade pigment with 50% white cement
and 50% ordinary cement sqm 0.1492+0.0202*
11.9.4 White cement without any pigment sqm 0.129+0.0202*
11.9.5 Light shade pigment with ordinary cement sqm 0.1695
11.9.6 Ordinary cement without any pigment sqm 0.1695
11.10 40 mm thick marble chips flooring with under layer 31mm
thick cement concrete 1:2:4.
11.10.1 Dark shade pigment with Ordinary cement sqm 0.1783
11.11 40 mm thick marble chips flooring with under layer 28 mm
thick cement concrete 1:2:4.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 11.0 FLOORING
456
work (Quintals)

11.12 Marble chips skirting :
11.12.1 18 mm thick with under layer 12 mm thick in
cement plaster 1:3 (1 cement : 3 coarse sand)
11.12.1.1 Dark shade pigment with ordinary cement sqm 0.1292
11.12.1.2 Light shade pigment with white cement sqm 0.0887+0.0405*
11.12.1.3 Medium shade pigment with 50% white cement
11.12.1.4 White cement without any pigment sqm 0.109+0.0405*
11.12.1.5 Light shade pigment with ordinary cement sqm 0.1292
11.12.1.6 Ordinary cement without any pigment sqm 0.1292
11.15 Crazy marble stone flooring
11.15.1 18 mm thick crazy marble stone white, black or
as specified sqm 0.1200+0.0405*
* White Cement
TILE FLOORING
11.16 Precast terrazo tiles 22mm thick in floors, and landings on
20mm thick bed of cement mortar (1:4).
11.16.1 Light shade using white cement sqm 0.0895+0.044*
11.16.2 Medium shade using 50%white cement and 50%
ordinary cement sqm 0.0917+0.0220*
11.16.3 Dark shade using ordinary cement sqm 0.0939
11.18 Precast terrazo tiles 22 mm thick in skirting and risers of
steps.
11.18.1 Light shade using white cement. sqm 0.0734+0.066*
11.18.2 Medium shades using 50% white cement and
50% ordinary cement. sqm 0.1064+0.033*
457
work (Quintals)
11.19 Chequered terrazo tiles 22 mm thick in floors on 20 mm thick

bed of cement mortar (1:4).
11.19.2 Medium shade using 50% white cement, 50%
ordinary cement sqm 0.0917+0.024*
11.20 Chequerred precast cement concrete tiles 22 mm thick in
foot path on 20 mm thick bed of cement mortar (1:4).
11.20.2 Medium shade using 50% white cement 50%
Grey cement sqm 0.1621+0.033*
11.21 Providing and fixing 10mm thick acid and or alkali resistant
tiles.
11.21.1 In flooring on a bed of 10 mm thick mortar 1:4
(1 acid proof cement : 4 coarse sand)
11.21.1.1 Acid and alkali resistant tile sqm 0.0786**
11.21.2 In dado/skirting on 12 mm thick mortar 1:4 (1 acid
proof cement : 4 coarse sand)
11.21.2.1 Acid and alkali resistant tile sqm 0.0862**
11.22 Tile work in skirting, risers of steps etc. with 8 mm thick
marble tile. sqm 0.1044
STONE FLOORING
11.23 Marble stone flooring with 18 mm thick marble stone over
20 mm thick cement mortar (1:4). sqm 0.13512
KOTA STONE FLOORING
11.26 Kota stone slab flooring over 20 mm thick bed of cement
mortar (1:4). sqm 0.1491
11.27 Kota stone slabs 20 mm thick in risers of steps, skirting etc.
laid on 12 mm (average) thick cement mortar 1:3. sqm 0.1374
SAND STONE FLOORING
11.28 40 mm thick fine dressed stone flooring over 20 mm (average)
thick base of cement mortar 1:5 with joints finished flush. sqm 0.0775
11.29 40 mm thick fine dressed stone flooring over 20 mm (average)
thick base of cement mortar 1:5 including pointing with cement
mortar 1:2. sqm 0.0931
458
work (Quintals)
11.30 40 mm thick rubbed stone flooring over 20 mm (average)

thick base of cement mortar 1:5 with joints 3mm thick, side
buttered with cement mortar 1:2. sqm 0.0931
CERAMIC GLAZED TILES
11.37 P/L ceramic glazed floor tiles laid on 20 mm thick Cement
Mortar (1:4) with grey cement slurry @ 3.3 kg/ sqm sqm 0.1242
11.38 P/L ceramic glazed floor tiles laid on 20mm thick bed of
Cement Mortar (1:4) with grey cement slurry @ 3.3 kg/ sqm sqm 0.1242
11.39 & P/L rectified Glazed Ceramic floor tiles laid on
11.40 20mm thick cement mortar (1:4). sqm 0.1242
VITRIFIED FLOOR TILES
11.41 P/L vitrified floor tile laid on 20mm thick cement mortar (1:4). sqm 0.1242
11.44 Crazy ceramic tile flooring. sqm 0.1046
11.46 P/L vitrified tile in skirting in cement mortar (1:3). sqm 0.088
11.51 P/L Machine cut, Mirror polished, Italian Marble stone flooring Sqm. 0.085 + 0.05*
11.52 P/L Machine cut Mirror polished Marble stone flooring Sqm. 0.085 + 0.05*
11.55 P/L flamed finish granite stone flooring 100 sqm. 13.50
11.56 P/L polished granite stone ......... 100 sqm. 13.50
* White cement
** Acid alkali resistant cement.
459
12.0 ROOFING
work (Quintals)
12.16 10 cm thick mud phaska with flat tile bricks grouted with
cement mortar (1:3). 100 sqm 3.11
12.17 10cm thick mud phaska with machine moulded tile bricks
grouted with cement mortar (1:3). 100 sqm 3.11
12.19 Providing and laying brick tiles over mumty roofs grouted
with cement mortar (1:3). 100 sqm 9.13
12.20 Providing and laying pressed clay tiles on roofs jointed
12.21 Providing gola 75x75 mm in cement concrete (1:2:4). metre 0.031
12.22 Making khurras 45x45 cm with average minimum thickness
of 5 cm cement concrete (1:2:4). each 0.06
12.23 Providing sand stone slab for roofing and laying cement
mortar (1 : 4). 100 sqm 0.74
12.38 Providing and fixing M.S. holder bat clamps in cement
concrete blocks 10x10x10cm of 1:2:4 mix. each 0.005
12.55 P/F heat resistant tile on roof with cement mortar (1:4) and
filling joints with white cement marble mix. sqm 0.1367
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 12.0 ROOFING
460
13.0 FINISHING
work (Quintals)
CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster:
13.1.1 1:4 (1 cement : 4 fine sand) 100 sqm 5.47
13.2 15 mm cement plaster:
13.3 20 mm cement plaster :
CEMENT PLASTER (IN COARSE SAND)
13.4.1 1:4 (1 cement : 4 coarse sand) 100 sqm 5.47
CEMENT PLASTER WITH A FLOATING COAT OF
NEAT CEMENT
13.7 12 mm cement plaster finished with a floating coat of
neat cement :
13.8 15 mm cement plaster finished with a floating coat of
neat cement :
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 13.0 FINISHING
461
work (Quintals)
13.9 Cement plaster (1:3) finished with a floating coat of neat
cement.
13.9.1 12 mm Cement Plaster 100 sqm 9.54
13.9.2 20 mm Cement Plaster 100 sqm 13.62
13.10 15 mm cement plaster (1:3) finished with a floating coat
of neat cement. 100 sqm 10.97
CEMENT PLASTER IN TWO COATS
13.11 18 mm cement plaster in two coats under layer 12 mm thick
cement plaster 1:5 finished with a top layer 6mm thick cement
plaster 1:6. 100 sqm 6.26
13.12 18 mm cement plaster in two coats under layer 12 mm thick
cement plaster 1:5 and a top layer 6mm thick cement
plaster (1:3). 100 sqm 8.13
13.13 12 mm cement plaster 1:2 (1 cement : 2 stone dust). 100 sqm 9.79
6 MM CEMENT PLASTER
13.17 6 mm cement plaster (1:3) finished with a floating coat of
neat cement. 100 sqm 5.87
13.18 Neat cement punning 100 sqm 2.20
ROUGH CAST PLASTER
13.19 Rough cast plaster in two layers, under layer 12 mm
cement plaster (1:4) and top layer 10mm cement
plaster (1:3). 100 sqm 11.59
PEBBLE DASH PLASTER
13.20 Pebble dash plaster in two layers, under layer 12mm
cement plaster 1:4 and top layer 10mm cement plaster
PLAIN CEMENT MORTAR BANDS
13.28 12 mm thick plain cement mortar bands in cement mortar
(1:4) : (Flush /Sunk / Raised / Moulded Band). 100 metre
1cm wide 0.053
13.29 18 mm thick plain cement mortar band in cement mortar 100 metre
(1:4) 1cm wide 0.076
462
work (Quintals)
13.30 18 mm thick moulded cement mortar band in two coats

under layer 12mm thick with cement mortar 1:5, top layer 100 metre
6mm thick with cement mortar (1:4). 1cm wide 0.07
POINTING OF BRICK WORK
13.31 Pointing on brick work with cement mortar (1:3) :
13.31.1 Flush / Ruled/ Struck or weathered pointing 100 sqm 1.53
13.31.2 Raised and cut pointing 100 sqm 2.04
POINTING ON TILE BRICK WORK
13.32 Pointing on tile brick work with cement mortar (1:3).
13.32.1 Flush/ Ruled/ Struck or weathered pointing 100 sqm 2.35
POINTING ON STONE WORK
13.33 Pointing on stone work with cement mortar (1:3).
13.33.1 Flush/ Ruled pointing 100 sqm 1.17
13.33.2 Raised and cut pointing 100 sqm 2.35
13.34 Raised and cut pointing on stone work in white cement
mortar (1:3). 100 sqm 2.35*
13.35 Pointing on stone slab ceiling with cement mortar (1:2). 100 sqm 1.02
13.72 Washed stone grit plaster on exterior walls in two layers
under layer 12mm cement plaster (1:4), top layer 15mm
cement plaster 1:1/2:2. 100 sqm 17.472
Note: - cement consumption for pointing is same for modular
& non modular bricks.
* White cement
463
14.0 REPAIRS TO BUILDING
work (Quintals)
14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches

with cement mortar 1:4. 100 sqm 6.95
14.2 Fixing chowkhats in existing opening with hold fasts in
cement concrete blocks with cement concrete 1:3:6.
14.2.1 Door chowkhats each 0.12
14.2.2 Window chowkhats each 0.06
14.2.3 Clerestory window chowkhats each 0.03
14.12 Providing and fixing 16 mm M.S. Fan clamps in existing
R.C.C. slab. each 0.016
14.13 Regrading terracing of mud phaska to proper slope. 100 sqm 3.11
14.14 Replacing sand stone slabs in roofing in cement mortar 1:4. 100 sqm 0.78
14.15 Renewing wooden battens in roofs & making good the holes
in walls. cum 0.36
14.16 Renewing wooden beams in roofs & making good the holes
in walls. cum 0.13
14.18 Flush pointing with cement mortar 1:3 for flat tile bricks on
top of mud phaska. 100 sqm 0.76
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 14.0 REPAIRS TO BUILDING
464
16.0 ROAD WORK
work (Quintals)
FENCING
16.23 P/F boundary stone including finishing smooth with cement
mortar (1:3). each 0.082
16.24 P/F precast R.C.C. kilometre stone including finishing smooth
in cement mortar (1:3).
16.24.1 35x111x25 cm size each 0.37
16.24.2 50x152.5x25 cm size each 0.698
16.24.3 35x93.5x18 cm size each 0.23
CONCRETE PAVEMENT
16.42 Cement concrete (1:2:4) in pavements. cum 3.20
16.43 Providing and laying design mix cement concrete of M-30
grade, in roads/ taxi tracks/ runways, using cement contentas
per design mix. cum 3.40
MISCELLANEOUS
16.49 Making bell mouth opening including providing cement
concrete (1:3:6) & plastering with cement mortar (1:3). 10 Nos. 6.60
16.52 Providing and fixing precast lime fly ash concrete blocks
including finishing with 10mm thick cement mortar (1:3),
in foot paths. sqm 0.05
16.63 P/L kerb channel 30cm wide and 50mm thick of cement
concrete (1:3:6). metre 0.11
16.67 Providing and fixing factory made RCC pavement slab of
M-30 grade in footpath over a bed of 20mm average thick
cement mortar (1:5). 100 sqm 7.75
16.69 Providing and laying factory made kerb stone of M-25 grade
jointed with cement mortar (1:3). cum 0.05
16.75 Providing and laying C.C. pavement of mix M-25 with
readymixed concrete. cum 3.30
16.80 Dry lean cement concrete sub base. cum 1.50
16.85 Laying old kerb stones, jointed with cement mortar (1:3). 100 metre 0.3723
16.86 P/L gang saw cut 18 mm thick, morror polished sqm 0.09
16.87 P/L gang saw cut 30 mm thick mirror polished sqm 0.09
16.88 P/L Matt finished vitrified tile of size sqm 0.12
16.89 P/L Matt finished vitrifid tile of size sqm 0.12
16.90 P/L tactile tile sqm 0.12
16.92 P/F 10x10x7.5 cm. granite stone block sqm 1.85
16.93 Providing and Placing in position 100mm thick precast
RCC covers on drain of footpath sqm 0.352
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 16.0 ROAD WORK
465
17.0 SANITARY INSTALLATIONS
work (Quintals)
17.1/17.2/ Fixing Indian European type W.C. pan. each 0.05

17.3
17.4 Fixing white vitreous china urinal basin :
17.4.1 One urinal basin with 5 litre white P.V.C. automatic
17.4.2 Range of two urinal basins with 5 litre white P.V.C.
17.4.3 Range of three urinal basins with 10litre white P.V.C.
17.4.4 Range of four urinal basins with 10 litre white P.V.C.
17.5 Fixing white vitreous china flat back half stall urinal :
17.5.1 Single half stall urinal with 5 litre P.V.C. automatic
17.5.2 Range of two half stall urinals with 5 litre P.V.C.
17.5.3 Range of three half stall urinals with 10 litre P.V.C.
17.5.4 Range of four half stall urinals with 10 litre P.V.C.
17.6 Fixing one piece construction white vitreous china squatting
plate :
17.6.1 Single squatting plate with 5 litre P.V.C. automatic
17.6.2 Range of two squatting plates with 5 litre P.V.C.
17.6.3 Range of three squatting plates with 10 litre P.V.C.
17.6.4 Range of four squatting plates with 10 litre P.V.C.
17.7 Fixing wash basin with C.I. brackets. each 0.025
17.8 Fixing white vitreous china pedestal for wash basin. each 0.016*
17.9 Fixing kitchen sink with C.I. brackets. each 0.025
17.12 Fixing draining board with C.I. brackets. each 0.014
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 17.0 SANITARY INSTALLATIONS
466
work (Quintals)
17.13 Fixing White vitreous china water closet squatting pan. each 0.025
17.17 Fixing a pair of white vitreous china foot rests. each 0.025
17.23 Fixing white vitreous china flat urinal basin. each 0.01
17.24 Fixing white vitreous china squatting plate urinal. each 0.02
17.25 Fixing white vitreous china wash basin. each 0.015
17.26 Fixing kitchen sink. each 0.015
17.27 Fixing kitchen sink. each 0.015
17.37 Providing and fixing M.S. holder-bat clamps. each 0.005
17.59 Providing and fixing M.S. stays and clamps. each 0.005
17.60 Providing and fixing trap of self-cleansing design. each 0.025
17.61 Cutting chases in brick masonry walls for sand cast iron/
centrifugally cast (spun) iron pipes and making good the
same with C.C.(1:3:6).
17.61.1 100 mm dia 100 metre 5.40
17.61.2 75 mm dia 100 metre 3.70
17.61.3 50 mm dia 100 metre 1.87
* White Cement.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 17.0 SANITARY INSTALLATIONS
467
18.0 WATER SUPPLY
work (Quintals)
18.1/18.4/ Providing and fixing G.I./ PE-AL-PE/ PP-R pipes.

18.7/18.10
18.10.1 15 mm dia nominal bore 100 metre 0.05
18.2/18.5/
18.8/18.11 P/F concealed pipes. 100 metre 0.88
18.32 Constructing masonry Chamber 30x30x50 cm, for
stop cock. each 0.26
sluice valve. each 1.44
18.36 Constructing masonry Chamber 60x60x75 cm, for fire
hydrants. each 1.30
water meter. each 1.34
18.76 Cutting holes up to 30x30 cm in walls including making
good the same. 100 Nos. 2.92
18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs
and repairing the hole after insertion of drain pipes etc.
with cement concrete (1:2:4). 100 Nos. 0.70
18.78 Making chases up to 7.5x7.5 cm in walls i/c finishing. 100 metre 0.88
18.79 Making hole up to 20x20 cm and embedding pipes up to
150 mm diameter in masonry and filling with cement
concrete (1:3:6). 100 metre 4.90
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 18.0 WATER SUPPLY
468
19.0 DRAINAGE
work (Quintals)
19.1 Jointing glazed stoneware pipes with stiff mixture of cement
mortar in the proportion of (1:1).
19.1.1 100 mm diameter 100 metre 2.17
19.2 Laying cement concrete (1:5:10) alround S.W. pipes:
19.2.1 100 mm diameter S.W. pipe 100 metre 19.24
19.3 Laying cement concrete (1:5:10) upto haunches of
S.W. pipes:
19.4 Providing and fixing square-mouth S.W. gully trap :
19.4.1 100x100 mm size P type each 0.27
19.4.2 150 x 100 mm size P type. each 0.26
19.4.3 180x150 mm size P type each 0.25
19.6 P/L NP2 class R.C.C. pipes with collars jointed with stiff
mixture of cement mortar in the proportion of (1:2):
19.6.1 100 mm dia. R.C.C. pipe 100 metre 0.50
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 19.0 DRAINAGE
469
work (Quintals)

19.7 Constructing brick masonry manhole in cement
mortar (1:4).
19.7.1 Inside size 90x80 cm and 45 cm deep each 2.92
19.7.2 & Inside size 120x90 cm and 90 cm.deep each 4.73
19.7.3
19.8 Extra for depth for manholes
19.8.1 Size 90x80 cm metre 1.26
19.8.2 Size 120x90 cm metre 1.52
19.9 Constructing brick masonry circular type manhole 0.91 m
internal dia at bottom and 0.56m dia at top in cement
mortar (1:4).
19.9.1 0.91 m deep each 2.75
19.10 Extra depth for circular type manhole 0.91m internal dia
(at bottom) with beyond 0.91m to 1.67m metre 1.40
19.11 Constructing brick masonry circular manhole 1.22 m internal
dia at bottom and 0.56m dia at top in cement mortar (1:4).
19.11.1 1.68 m deep each 5.39
19.12 Extra depth for circular type manhole 1.22m internal dia
(at bottom) beyond 1.68 m to 2.29 m. metre 1.43
19.13 Constructing brick masonry circular manhole 1.52 m internal
dia at bottom and 0.56 m dia at top in cement mortar (1:4).
19.13.1 2.30 m deep each 10.86
19.14 Extra depth for circular type manhole 1.52 m internal dia
(at bottom) beyond 2.30 m. metre 3.11
19.15 Providing M.S. foot rests including fixing in manholes with
20x20x10 cm cement concrete blocks (1:3:6). 100 nos. 0.88
19.16 Providing orange colour safety foot rest. 100 nos. 1.98
19.17 Replacement of M.S. foot rests in manholes with
20x10x10 cm C.C. blocks (1:3:6) mix. 100 nos. 0.88
470
work (Quintals)
19.19 Providing and fixing in position precast R.C.C. manhole cover

and frame.
19.19.1 LD- 2.5
19.19.1.1 Rectangular shape 600x450mm internal
dimensions each 0.128
19.19.1.2 Square shape 450mm internal dimensions each 0.096
19.19.1.3 Circular shape 450mm internal diameter each 0.096
19.19.2 M D - 10
19.19.2.1 Square shape 450mm internal dimension each 0.128
19.19.2.2 Circular shape 500mm internal diameter each 0.096
19.19.3 H D - 20
19.19.4 EHD - 35
19.19.4.1 Circular shape 560 mm internal dia each 0.096
19.21 Making connection of drain or sewer line with existing
manhole and making good the walls, floors with C.C.
(1:2:4) mix.
19.22 Providing sand cast iron drop connection externally for 60 cm
drop from branch sewer line to main sewer manhole. :
19.23 Extra for depths beyond 60 cm of sand cast iron drop
connection. :
19.23.1 For 100 mm dia. sand cast iron drop connection metre 0.21
19.23.2 For 150 mm dia. sand cast iron drop connection metre 0.26
19.27 Constructing brick masonry road gully chamber 50x45x
60cm in cement mortar (1:4). each 0.93
77.5 cm in cement mortar (1:4). each 0.82
77.5 cm in cement mortar (1:4). each 1.66
471
work (Quintals)
19.30 Constructing brick masonry chamber for underground C.I.

inspection chamber and bends in cement mortar (1:4).
19.30.1 Inside dimensions 455x610 mm and 45 cm deep
for single pipe line each 0.90
19.30.2 Inside dimensions 500x700 mm and 45 cm deep for
pipe line with one or two inlets each 1.02
19.30.3 Inside dimensions 600x 850 mm and 45 cm deep for
pipe line with three or more inlets each 1.27
19.31 Extra for depth beyond 45 cm of brick masonry chamber :
19.31.1 For 455x610 mm size metre 0.87
19.32 Making soak pit 2.5 m diameter 3.0 metre deep. each 0.072
19.34 Providing and fixing S.W. intercepting trap in manholes with
stiff mixture of cement mortar (1:1).
19.34.1 100 mm dia each 0.013
19.34.2 150 mm dia each 0.019
19.35 P/L Non pressure Np-3 class
19.35.1 450 mm dia RCC pipe 100 metre 1.20
19.36 P/L Non pressure Np-4 class
472
20.0 PILE WORK
work (Quintals)
20.1 Providing, driving and installing driven cast-in-situ reinforced

cement concrete piles of grade M -25.
20.2 Boring, providing and installing bored cast-in-situ reinforced
cement concrete piles of grade M -25 by tripod and mechanical
winch machine.
20.2A Boring, providing and installing bored cast-in-situ reinforced
cement concrete piles of grade M -25 by crawler mounted,
telescopic boom hydraulic pilling Rig.
20.2A.5 1500 mm dia pile metre 5.830
20.3 Boring, Providing and installing cast in situ single under
reamed piles of grade M -25.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 20.0 PILE WORK
473
work (Quintals)
20.4 Extra for providing additional blub in under reamed piles.

20.4.1 300 mm dia piles each 0.109
20.5 Providing, driving and installing driven Pre-cast reinforced cement

concrete piles of grade M -25.
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 20.0 PILE WORK
474
22.0 WATER PROOFING
work (Quintals)
22.1 P/L integral cement based treatment for water proofing on
horizontal surface. :
22.1.1 Using rough kota stone sqm 0.342
22.2 P/L integral cement based treatment for water proofing on
the vertical surface. :
22.2.1 Using rough Kota stone sqm 0.443
22.3 P/L water proofing treatment to vertical and horizontal
surfaces of depressed portions of W.C., kitchen and the like
consisting of:
i) Ist course of applying cement slurry @ 4.4 kg/sqm
ii) IInd course of 20mm cement plaster (1:3)
iii) IIIrd course of applying blown or residual bitumen applied
hot at 1.7 Kg. per sqm of area
iv) IVth course of 400 micron thick PVC sheet sqm 0.158
22.5 P/L water proofing treatment in sunken portion of WCs,
bathroom etc. sqm 0.0123
22.6 P/L water proofing treatment on roofs. sqm 0.0195
22.7 P/L integral cement based water proofing treatment on roofs,
balconies, terraces etc. :
22.7.1 With average thickness of 120mm and minimum
thickness at khurra as 65 mm sqm 0.387
22.14 Grading roof for water proofing treatment with
22.14.1 Cement concrete 1:2:4 cum 3.20
22.14.2 Cement mortar 1:3 cum 5.10
22.14.3 Cement mortar 1:4 cum 3.80
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 22.0 WATER PROOFING
475
26.0 NEW TECHNOLOGIES AND MATERIALS
work (Quintals)
26.31.1 SBR Polymer (@10% of cement weight) modified cementitious

bond coat @2.2 kg cement per sqm. 100 sqm 2.20
26.32 Providing, mixing and applying SBR polymer (of approved
make) modified Cement mortar in proportion of 1:4 (1 cement:
4 graded coarse sand with polymer minimum 2% by wt. of
cement used) .
26.32.1 12 mm average thickness. 100 sqm 5.47
26.32.2 25 mm average thickness in 2 layers. 100 sqm 11.40
26.32.3 50 mm average thickness in 3 layers. 100 sqm 22.80
26.33 Providing, mixing and applying SBR polymer (of approved make
@ minimum 2% by wt. of cement used) modified plain/reinforced
cement concrete for structural members.
26.33.1 50mm thick in Grade M 25 with cement content not
less than 330 kg per cum 100 sqm 16.50
26.34 Providing and laying SBR Polymer modified (of approved make
@ minimum 2% by wt. of cement used) plain/reinforced concrete
jacket for the structural members e.g. columns, pillars, piers,
beams etc with concrete.
26.35 Providing and injecting approved grout in proportion recommended
by the manufacturer into cracks/honey-comb area of concrete/
masonry by suitable gun/pump.
26.35.1 Stirrer mixed Acrylic Polymer of approved make @ 2%
of weight of cement used) modified Cement slurry
made with non shrink compound in concrete/RCC
work 100 kg 1.00
26.35.2 Stirrer mixed SBR Polymer (of approved make)
modified Cement slurry made with Shrinkage
Compensating Cement in concrete/RCC work. 100 kg 1.00
COEFFICIENTS FOR CEMENT CONSUMPTION S.H. : 26.0 NEW TECHNOLOGIES AND MATERIALS
476
Code Description Unit Quantity of
No. cement per unit
quantity of work
(Quintals)
26.38 Shotcreting R.C.C. columns, beams and slabs etc. in layers
with approved design mix concrete having .
26.46 Providing and fixing in position, 200 mm thick factory made
Expanded olystyrene Core (EPS Core) wall panels consisting
of EPS core sandwiched between two Engineered
sheets of welded wire fabric mesh.....................applying the
layer of 50 mm thick cement mortar 1:3 (1 cement: 3 coarse
sand) 100 sqm 51.00
26.47 Providing and fixing in position, 230mm thick factory made
Expanded Polystyrene Core (EPS Core) roof/floor panels.
.......... applying a layer of 60-65 mm thick cement mortar
1: 3 {1 cement: 3 coarse sand............ applying 70-75 mm thick
layer of cement concrete 1:1.5: 3 (1 cement :1.5 coarse sand :
3 graded stone aggregate 20 mm nominal size). 100 sqm 58.60
26.53 Filling of empty cavities with quarry dust mixed with cement cum 0.72
26.58 Filling of joints between RCC plinth beam/floor slab and wall
panel of external walls 100 metre 0.03125
26.59 Waterproofing treatment of vertical joints between door frame,
window & ventilator frames 100 metre 0.03125
26.61 In filling/ sealing of joint between RCC lintel cum sunsdhade
and wall 100 metre 0.03125
26.66 P/F factory made EPS wall panels consisting EPS core
sandwhiched between two Enginered sheets sqm 0.357
26.68 P/F Factory made Precast Concrete solid blocks in foundation
and plinth cum 0.2825
26.69 P/F Factory made Precast Concrete solid blocks in
superstructure above plinth level up to floor V level cum 0.2825
Precast concrete solid blocks in foundation and plinth 100 sqm 2.6904
26.71 Providing and laying half block masonry with factory
made Precast concrete solid blocks insuperstructure above
plinth level up to floor V level 100 sqm 2.6904
26.73.1 Fabrication & Manufacturing of prestressed Hollow Core
slab of concrete grade M-40 (cement conetent 400kg)
477
No. cement per unit
quantity of work
(Quintals)
26.73.2 Extra for using M-50 (Cement content 425kg) instead
of M-40
26.73.3 Extra for using M-60 (Cement content 440kg) instead of M-40
26.74 Fabrication and maufacturing of solid precast concrete
element for walls,stairs,column etc.,
26.74.1 Concrete grade M-35 (Cement content 370kgs) cum 3.70
26.74.2 Extra for using M-40 (Cement content 400 kg)
instaed of M-35 cum 0.30
478
COEFFICIENTS
FOR BITUMEN
CONSUMPTION
479
2.0 COEFFICIENTS FOR BITUMEN CONSUMPTION
16.0 ROAD WORK
Code Description Unit Quantity of bitumen
work (Quintals)
SURFACE DRESSING
16.25 Surface dressing on new surface with paving bitumen of
grade VG -10. sqm 0.0225
16.26 Surface dressing on new surface in two coats with bitumen
of grade VG -10. sqm 0.029
16.27 Surface dressing on old surface with hot bitumen of grade
VG -10. sqm 0.0195
16.28 Surface dressing one coat on new surface :
16.28.1 Using bitumen emulsion sqm 0.0195
16.29 Surface dressing one coat on old surface :
16.29.1 Using bitumen emulsion sqm 0.0122
PREMIX CARPET
16.30 Providing and applying tack coat with bitumen of grade VG-10 :
16.30.1 On W.B.M. @ 0.75 Kg / sqm sqm 0.0075
16.30.2 On bituminous surface @ 0.50 Kg / sqm sqm 0.0050
16.31 Providing and applying tack coat using bitumen emulsion
(Rapid Setting):
16.31.1.1 On W.B.M @ 0.4kg/sqm sqm 0.0040
16.32 2 cm premix carpet surfacing with paving asphalt VG-10/
VG-30/modified bitumen CRMB 55. sqm 0.0144
16.33 2.5 cm premix carpet surfacing with paving asphalt VG-10/
VG-30/modified bitumen CRMB 55. sqm 0.018
16.34 2 cm premix carpet surfacing with bitumen emulsion. sqm 0.0255*
16.35 2.5 cm premix carpet surfacing with bitumen emulsion. sqm 0.0313*
16.36 Providing and laying Bitumen Penetration Macadam :
16.36.1 For 50mm compacted thickness with paving
asphalt VG-10 @ 50 kg/10 sqm sqm 0.050
16.36.2 For 75 mm compacted thickness in two layers
with paving asphalt VG-10 @ 68 kg/10 sqm sqm 0.068
MASTIC AND BITUMASTIC WEARING COURSE
16.37 Providing and laying bitumen mastic wearing course:
16.37.1 25 mm thick sqm 0.0588
16.37.2 40 mm thick sqm 0.0941
COEFFICIENTS FOR BITUMEN CONSUMPTION S.H. : 16.0 ROAD WORK
480
work (Quintals)
16.38 2.5 cm thick bitumastic sheet with hot bitumen, paving

asphalt VG-10/VG-30/modified bitumen CRMB 55. sqm 0.0303
16.39 4 cm thick bitumastic sheet with hot bitumen, paving
asphalt VG-10/VG-30/modified bitumen CRMB 55. sqm 0.0479
SEAL COAT
16.40 P/L seal coat using 128 kg of bitumen of grade VG-10. sqm 0.0077
16.41 P/L seal coat using 98 kg of bitumen of grade VG-10. sqm 0.0098
16.54 P/L Dense Bituminous macadam :
16.54.1 50 to 100 mm average compacted thickness with
bitumen of grade VG-30 @ 5% (percentage by weight
of total mix) and lime filler @ 2% (percentage by
weight of Aggregate) prepared in Batch Type Hot Mix
Plant of 100-120 TPH capacity. cum 1.1538
bitumen of grade VG-30 @ 5% (percentage by weight
of total mix) and lime filler @ 2% (percentage by
weight of Aggregate) prepared in Drum Type Hot Mix
16.55 Providing and laying Bituminous Macadam.
bitumen of grade VG-30 @ 3.50% (percentage
by weight of total mix) prepared in Batch Type Hot
Mix Plant of 100-120 TPH capacity. cum 0.7683
bitumen of grade VG-30 @ 3.50% (percentage
by weight of total mix) prepared in Drum Type Hot
Mix Plant of 60-90 TPH capacity. cum 0.7683
16.56 Providing and laying Semi Dense Bituminous concrete
16.56.1 25 mm compacted thickness with bitumen of grade
VG-30 @ 5% (percentage by weight of total mix) and
prepared in Batch Type Hot Mix Plant of
100-120 TPH capacity. 100 sqm 2.8846
16.56.2 25 mm compacted thickness with bitumen of grade
VG-30 @ 5% (percentage by weight of total mix) and
prepared in Drum Type Hot Mix Plant of
60-90 TPH capacity. 100 sqm 2.8846
481
work (Quintals)
16.57 P/L Bituminous Concrete :

VG-30 @ 5.5% (percentage by weight of total mix)and
prepared in Batch Type Hot Mix Plant of 100- 120
VG-30 @ 5.5% (percentage by weight of total mix)
and lime filler @ 3% (percentage by weight of
Aggregate) and waste plastic additive @ 8%
(percentage by weight of bitumen) prepared in Batch
PMB-40 @ 5.5% (percentage by weight of total
mix)and lime filler @ 3% (percentage by weight of
Aggregate) prepared in Batch Type Hot Mix Plant of
100-120 TPH capacity. cum 1.2958
CRMB-60 @ 5.5% (percentage by weight of total
Aggregate) prepared in Batch Type Hot Mix Plant of
and waste plastic additive @ 8% (percentage by
weight of bitumen) prepared in drum Type Hot Mix
PMB-40 @ 5.5% (percentage by weight of total mix)
and lime filler @ 3% (percentage by weight of
Aggregate) prepared in drum Type Hot Mix Plant of
CRMB-60 @ 5.5% (percentage by weight of total
Aggregate) prepared in Drum Type Hot Mix Plant of
* Including tack coat
482
2.0 COEFFICIENTS FOR BITUMEN CONSUMPTION
22.0 WATER PROOFING
No. bitumen per unit
quantity of work
(Quintals)
SURFACE DRESSING
22.3 P/L water proofing treatment to vertical and horizontal surfaces
of depressed portions of W.C., kitchen and the like.. sqm 0.0170
22.6 P/L water proofing treatment on roofs with cement slurry & fibre
glass cloth. sqm 0.0097
22.8 P/L four courses water proofing treatment with bitumen felt over
roofs:
22.8.1 Bitumen felt (hessian base)type 3 grade I sqm 0.0290
22.9 P/L six courses water proofing treatment with bitumen felt over
roofs applied hot @ 1.45, 1.20 & 1.45 for 1st, 3rd and 5th course. sqm 0.041
22.10 & P/L six courses water proofing treatment with bitumen felt over
22.11 roofs applied hot @ 1.45, 1.20 & 1.70 for 1st, 3rd and 5th course. sqm 0.0435
22.15 P/L in situ seven course water proofing treatment with APP
(1.5 mm thick @ 2.25 kg./sqm). sqm 0.036
22.16 P/L in situ five course water proofing treatment with APP
22.17 P/L in situ seven course water proofing treatment with APP
22.18 P/F APP.
22.18.1 2 mm (for corrugated roof sheets) sqm 0.0035
22.19 P/L APP modified prefabricated five layer, 3 mm thick water
proofing membrane. Tear strength in longitudinal and transverse
direction as 60/80N.
22.19.1 3 mm thick sqm 0.0035
22.20 P/L APP modified prefabricated five layer 3 mm thick water
proofing membrane. Tear strength in longitudinal and transverse
direction as 300/250N.
22.20.1 3 mm thick sqm 0.0035
COEFFICIENTS FOR BITUMEN CONSUMPTION S.H. : 22.0 WATER PROOFING
483
Hkkjr ljdkj
GOVERNMENT OF INDIA
CENTRAL PUBLIC WORKS DEPARTMENT
fnYyh nj vuqlwph
¼Hkkx - 1½
(Vol. 1)
2018
egkfuns”kd] ds-yks-fu-fo-] ubZ fnYyh ds izkf/kdkj ds v/khu izdkf”kr

© All rights reserved. No part of this publication, either in English or in Hindi, may be reproduced in any form
or by any means, electronic or mechanical including photocopy, recording or any information storage and
retrieval system, without permission, in writing, from the Director General, CPWD, New Delhi.
DISCLAIMER
The rates taken in Delhi Schedule of Rates 2018 are indicative and actual rates shall be governed by the
market forces. Further its use by Govt. Departments, PSUs, private bodies & individuals shall be at their own
risk and discretion. CPWD shall not be responsible for any ambiguity, discrepancy, dispute or financial loss,
arising directly or indirectly by using or following items of DSR by such Govt./Private bodies or individuals.
For feed back and suggestions, please contact SE(TAS), CPWD, Room No. 418, ''A'' Wing, Nirman
Bhawan, New Delhi. Tel. No. 011-23062339, Email: [email protected]
A GOVERNMENT OF INDIA PUBLICATION

Published by
DIRECTOR GENERAL
CPWD, Nirman Bhawan, New Delhi - 110011
&
Printed & Marketed by
JAIN BOOK AGENCY JAIN BOOK DEPOT

Authorised Dealers of Govt. Publications C - 4, Opp. PVR Plaza, Post Box. No. 51,
C-9, Connaught Place, New Delhi-110001 Connaught Place, New Delhi-110001 (India)
Phones : 011- 44556677, 23416390 upto 94 Phone : 011- 23416101 / 02 / 03
E-mail : [email protected] E-mail : [email protected]
Website : www.jainbookagency.com
JAIN BOOK AGENCY (SOUTHEND) JAIN BOOK AGENCY (GURGAON)

1, Aurobindo Place Market, 19, Central Plaza Mall, Sector 53,
Hauz Khas, New Delhi-110016 Golf Course Road,
Phone : 011- 41755666 Gurgaon 122002 Haryana
E-mail : [email protected] Phone : 0124- 4042665
Website : www.jainbookagency.com Mobile : 9810666810
JAIN BOOK AGENCY (INTERNATIONAL) JAIN BOOK AGENCY (GREATER NOIDA)

RA- 11, Sector- 126, 11 Jagat farm Complex
Opp. Gate No. 2A of Amity University, Gama Sector Market
Noida Near OBC Bank
Mobile. : 9210080580 Greater Noida
Phone : 0120-4206655
Distributed by
JAIN BOOK AGENCY (CENTRAL)
4574/15, 2nd Floor, Padamchand Marg,
Near Happy School, Daryaganj, New Delhi-110002
Phone : 011- 43513689, 43513570
Mob: 9667274446, 9810666810
E-mail : [email protected]
Also available at
All Leading Booksellers & Authorised Govt. Dealers In India
Price : Rs. 1200/- (for both volumes) excluding postage and forwarding charges etc.
Hkkjr ljdkj dsUnzh; yksd fuekZ.k foHkkx
Government of India fuekZ.k Hkou] ubZ fnYyh 110011
PRABHAKAR SINGH Nirman Bhawan, New Delhi- 110011
Director General Tel : 23062556 / 1317, Fax : 23061884
E-Mail : [email protected]
FOREWORD
Delhi Schedule of Rates, being published by Central Public Works
Department from time to time, is a comprehensive and useful Technical
Document in execution of Civil Construction Works. Apart from CPWD, this
Schedule of Rates is used as a guide by many Departments, Institutions,
Public Sector Undertakings, Architects, Builders and Contractors etc.
CPWD Schedule of Rates was first published in the year 1931, followed by a
number of revisions/publications from time to time in order to bring it in line
with the prevailing materials,technologies and market rates. Delhi Schedule of
Rates were revised and issued in subsequent years viz 1977,
1981, 1985, 1989, 1993, 1997, 2002, 2007, 2010 (Reprint), 2012, 2013, 2014
& 2016.
Last Delhi Schedule of Rates was published in the year 2016. Revision of this
DSR has become necessary due to change in wages of labour & price of
materials, adoption of new construction technologies & materials as well as
implementation of GST. These components have been incorporated in the
DSR 2018 by revising DSR 2016.
I wish to place on record the technical input and effective coordination on the
part of Shri A.S. Arora, ADG (S&P), Dr K M Soni ADG (TD), Shri Manu
Amitabh CE (CSQ) (Civil) and the efforts put in by Shri Divakar Agrawal SE
(TAS). Shri D.S.Panwar EE(TAS-I), Shri M L Prasad EE(TAS-II),
Shri D.S. Adhikari AE (QA), Shri Naveenkumar P JE (TAS) and team of officers
in CSQ unit in finalizing the DSR-2018 in a short time.
I am sure that Delhi Schedule of Rates 2018 will be quite useful to all
concerned Engineers & Architects in Building Construction Industry in general
and CPWD in particular.
Place: New Delhi (PRABHAKAR SINGH)

Date: December 14, 2018 Director General
Hkkjr ljdkj
Government of India
DR K.M. SONI fuekZ.k Hkou] ubZ fnYyh 110011
Addl. Director General (TD)
Nirman Bhawan, New Delhi- 110011
PREFACE
1. DSR i.e. Delhi Schedule of Rates-2018 includes the existing items of DSR 2016 with deletion of
few items not in practice, merger of similar items and addition of new items in line with emerging
trends in construction Industry.
2. DSR-2018 is based on the prevailing market rates of materials in Delhi as on 01.10.2018. The
labour rates adopted are as per minimum wages applicable w.e.f 01.10.2018 issued by Govt. of
Delhi/ Govt. of India, whichever is higher.
3. The cost index for DSR 2018 is 118 with reference to CPWD Plinth Area Rates 2012, having
base 100 as on 01.10.2012.
4. The technical sanctioning authority may decide rates of non-schedule items judiciously
based on market rates without adding cost index.
5. This DSR - 2018 shall be read along with CPWD specifications 2009 Vol.-I & II with up to date
Correction Slips.
6. Following are the Salient Features of DSR- 2018:
6.1 DSR-2018 is bilingual and in two volumes.
6.1.1 The rates of basic materials incorporated in this DSR - 2018 are considered for the materials
available in the market conforming to BIS Standards/ CPWD Specifications.
6.1.2 The effect of GST on works contracts has been incorporated in all the items.
Salient Modifications and Changes in Sub Heads:
7.1 Earth work: Item No. 2.25(a) Excavating, supplying and filling of local earth by mechanical
transport up to a lead of 5km has been added.
7.2 Reinforced Cement Concrete: Item No. 5.22B & 5.22C Steel Reinforcement for R.C.C work
ready to use “Cut bend” rebars have been added. Nomenclature of item no.5.9 modified. Item
no.5.50 to 5.57 shifted to sub head 26 i.e. New Technologies & Materials (26.73 to 26.80).
IV
7.3 Brick Work: Sub head 6- Brick work has been renamed as Masonry work.
7.4 Marble & Granite work: Sub head 8- Marble & Granite work has been renamed as Cladding
work and all the cladding items have been shifted in this sub head from other Sub heads i.e. 7.0,
9.0, 11.0 & 25.0.
7.5 Wood and PVC Work: The amendments have been made in nomenclature of Item Nos. 9.138,
9.163 & 9.164.
7.6 Roofing: The amendments have been made in nomenclatures of item Nos. 12.8 to 12.10 and
12.12 to 12.13.
7.7 Finishing: Item No.13.48A for finishing walls with 100% Premium Acrylic Emulsion paint having
VOC less than 50gm/litre and UV resistance as IS: 15489:2004 has been added.
7.8 Road Work: The nomenclature of Item No.16.81‘Providing and erecting 2.00 metre temporary
barricading at site’ has been modified.
7.9 Water Supply: Items Nos. 18.4, 18.5, 18.6 & 18.6A for Polypropylene Random Copolymer
(PP-R-C) pipes have been added.
7.10 Structural Glazing Aluminum Panel: The nomenclature of item No. 25.3 has been modified.
7.11 Item No. 26.20 & 26.21 have been shifted to sub head 14.0
8.0 New Technologies and Materials
With a view to give boost to make in India initiative of the Government, new technology items have
been added in New Technologies and Materials sub Head. These new items are included for a
period of two years and then performance shall be reviewed. Following are the items added under
this sub head:
8.1 Bamboo mat corrugated sheet (BMCS),Bamboo mat ridge cap(BMRC),false ceiling of Phenol
Bamboo mat board, wall paneling with Phenol bonded Bamboo mat board (item no.26.6 a to e ).
8.2 EPS cement sandwich light weight solid core panels (item no.26.49).
8.3 Non Asbestos fibre reinforced aerated sandwich wall/roof/floor light weight solid core panels
(item no.26.50).
8.4 GFRG items (item no.26.51 to 26.61)
8.5 Speed floor system (Item no.26.62 to 26.64).
8.6 Factory made fast track modular system (Item no.26.65 to 26.66)
V
8.7 External thermal insulation in composite system (Item no.26.67)
8.8 Precast solid cement concrete blocks and paver blocks made of C & D waste (Item no.26.68
to 26.72)
8.9 Prefab/Precast technology (Item no.26.73 to 26.80)
8.10 Scaffolding net (Item no. 26.81)
9.0 Lot of efforts has gone into the preparation of this Delhi Schedule of Rates. I convey my
deep appreciation and sincere thanks to:
Shri Manu Amitabh CE, (CSQ) ; Shri Divakar Agrawal SE, (TAS) ; Shri Sudhir Kumar
Dak SE, (C&M) ; Shri D.S Panwar EE-(TAS-I) ; Shri M.L Prasad EE-(TAS-II) ;
Shri P. Goyal EE-(TAD) ; Shri A K Sikka EE, (QA) ; Shri M.C. Singal EE, (QA) ;
Shri S N Jaiswal EE, (HQ) ; Shri Shivani Kaushal EE, (M) ; Shri Sajal Mitra EE, (CON) ;
Shri Kunwar Chandresh EE, (TLC) ; Shri D.S. Adhikari AE, (QA) ; Shri D. K. Malhotra
AE, (TAS) ; Shri Patta Madhukumar AE, (TAS) ; Shri Prabhat Kumar Srivastav AE,
(TAS) ; Shri Gurmeet Singh AE, (TAD) ; Shri H. K. Gupta AE, (M) ; Shri Mohammad
Tarik AE, (QA) ; Shri S.K. Sharma AE, (QA) ; Shri Gopal Warshney AE, (QA) ;
Shri K R Meena AE, (CON) ; Shri Ved Khurana AE, (TLC) ; Shri Jai Bhagwan AE, (M) ;
Shri Chalapaka Ramaraju JE, (TAD) ; Shri Naveenkumar P. JE, (TAS); Shri Jay Prakash
Chief Estimator (TAS) ; Shri Bhim Singh Sr. D/man (TAS) ; Shri Sanjay Singh AD, (OL) and
his team for hindi translation of DSR- 2018, Shri Yogendra Pal Singh Yadav, Dy. Architect,
O/o ADG (Arch.), Shri Gaurav Sarswat Asstt. Architect, O/o ADG (Arch.) for Graphic designing
of DSR 2018 and other officers and staff of CSQ unit whose names are not mentioned here,
for their sincere efforts made in the preparation of this document in such a short time.
Various Committees and field units, who contributed field inputs, also deserve appreciation
for their timely help.
10.0 Although due care has been taken to print the DSR- 2018 as correctly as possible, there is
possibility that some errors might have crept in inadvertently. In case, any error or omission
is noticed, it may be brought to the notice of Superintending Engineer (TAS), CPWD,
Room no. 418, ‘ A’, Nirman Bhawan, New Delhi – 110011 (Tele fax. 011-23062339 ).
And suggestions for improvement are always welcome.
(Dr K M SONI)
ADG (TD) CPWD
Note: - In case of any discrepancy between English and Hindi versions, the English version shall
be held valid.
VI
C O N T E N T S
Vol. 1
A. BASIC RATES
0.1 HIRE CHARGES OF PLANTS & MACHINERY 2
0.2 LABOUR 6
0.3 MATERIALS 8
0.4 CARRIAGE CODES 61
B. SUB -HEADS
1. Carriage of Materials 64
2. Earth Work 72
3. Mortar 80
4. Concrete Work 83
5. Reinforced Cement Concrete 90
6. Masonry Work 105
7. Stone Work 113
8. Cladding Work 120
9. Wood and PVC Work 130
10. Steel Work 179
11. Flooring 188
12. Roofing 203
Note : For Sub Heads 13 to 26 refer to Vol. 2
VII
C O N T E N T S
Vol. 2
13 Finishing 224
14 Repairs to Building 240
15 Dismantling and Demolishing 256
16 Road Work 264
17 Sanitary Installations 289
18 Water Supply 314
19 Drainage 357
20 Pile work 371
21 Aluminium Work 378
22 Water Proofing 385
23 Rain Water Harvesting & Tubewells 394
24 Conservation of Heritage Buildings 400
25 Structural Glazing Aluminium Composite Panel 404
26 New Technologies and Materials 411
C. CEMENT CONSUMPTION STATEMENT 444
D. BITUMEN CONSUMPTION STATEMENT 479
VIII
(Vol. 1)
fnYyh nj vuqlwph
¼Hkkx - 1½
2018
BASIC
RATES
1
BASIC RATES
0.1 HIRE CHARGES OF PLANTS & MACHINERY
Note :- These rates are exclusive of GST, contractor’s profit and over heads etc.

No.
0005 Hire charges of Diesel Truck - 9 tonne day 2000.00
0006 Hire charges of Spraying machine including electric charges day 250.00
0007 Hire charges of Coaltar Sprayer day 300.00
0008 Hire charges of Barber green, drying, mixing and Asphalt Plant,
with accessories, capacity 30/45 tonne day 7700.00
0010 Hire charges of Derrick monkey rope day 750.00
0015 Hire and running charges of Tripod and Mechanical Winch
machine complete with power unit and accessories day 1900.00
0016 Mastic Cooker day 750.00
0019 Hand Grinder for mirror polish day 250.00
0021 Pin vibrator day 325.00
0022 Surface Vibrator day 400.00
0023 Hot Bitumen Mixer 0.5 cum i/c hand cart day 3500.00
0024 Hire and running charges of hydraulic piling rig with power
unit etc. including complete accessories and shifting at site day 30000.00
BASIC RATES : 0.1 HIRE CHARGES OF PLANTS & MACHINERY
2
No.
0027 Hire and running charges of vibrating pile driving hammer

complete with power unit and accessories day 30000.00
0031 Steam curing by using boiler /Heater cum 500.00
0032 Stressing Machine (jack with pump) day 11500.00
0033 Paint applicator day 750.00
0034 Cutting saw machine day 1350.00
0035 Strands Roller machinery for laying strands day 3500.00
0036 Bed master (Pulling strands) day 3000.00
0039 Tractor with trolley day 1350.00
0040 Air compressor 250 cfm with two leads for pneumatic cutters /
hammers day 1600.00
0042 C.C .batch mix plant day 10000.00
0043 Road sweeper day 550.00
0045 Slip form paver with sensor day 13000.00
0046 Water tanker 5000 litre day 1200.00
0047 Concrete joint cutting machine day 900.00
0048 Texturing machine day 925.00
0049 Dozer D-80-A 12 hour 1500.00
0050 Motor Grader 3.35 metre blade hour 2450.00
0051 Hydraulic Excavator of 1 cum bucket hour 1000.00
0052 Front end loader 1 cum bucket capacity (incl POL) hour 900.00
0053 Tipper-5 Cum tonne/km 3.00
0054 Vibratory roller 8 to 10 tonne hour 600.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 300.00
0056 Tandem Road Roller hour 1200.00
0057 Water Tanker 5 to 6 KL capacity hour 150.00
3
No.

0059 Wet Mix Plant 60 TPH hour 800.00
0060 Mechanical Broom Hydraulic hour 360.00
0061 Emulsion Pressure Distributor of capacity 1750 sqm per hour hour 800.00
0062 Hot mix Plant -120 TPH capacity hour 15000.00
0063 Hot mix Plant 100 TPH Capacity hour 13000.00
0064 Paver finisher Hydrostatic with sensor control 100 TPH hour 1500.00
0065 Paver finisher Mechanical 100 TPH hour 800.00
0068 Concrete Paver finisher with 40 HP Motor and sensor hour 3000.00
0069 Generator 250 KVA hour 350.00
0071 Truck 5.5 cum/10 tonnes tonne km 3.00
0072 Cost for crane having capacity 50MT day 8500.00
0075 Road sweeper (Mechamical Broom) @ 1250 sqm per hour hour 350.00
0076 Drum Type HMP of 60-90 TPH capacity @ 75 tonne per hour
actual output hour 12000.00
0080 Hire and running charges of drill machine up to 400 mm dia
(including cost of mobile oil, diesel consumption in ordinary soil
and operator) day 7500.00
0081 Pile Integrity testing equipment day 3000.00
0082 Excavation of Diaphragm wall by Mechanical Grab sqm 1300.00
0083 Hire charges of TATA 407 or equivalent for local shifting. day 1200.00
Note :- 1. Above hire - charges (from item code 0001 to 0083)
include cost of services of operating staff, Cost of lubricating
oil, diesel / Petrol/ Kerosene oil , other consumables for
running the plant and machinery and excluding GST. 2. The
hire charges of plant machinery on per day basis are for
single shift of eight working hours.
0084 Hire charges of diesel truck - 9 tonne (witout POL) day 1500.00
0085 Using cost of Ultra Violet Radiation tube Hour 189.00
0086 Compressor, gun, rubber pipes & other accessories- hire charge of
plant & machinery i/c necessary fuel day 4000.00
4
No.

0090 Hire charges of compressor day 420.00
0092 Hire charges of plant and Machinery that can inject 350 kg/day day 200.00
5
BASIC RATES
0.2 LABOUR
Note :- These rates are exclusive of GST, contractor’s profit and over heads and are inclusive of
wages for weekly day of rest.

No.
0128 Mate day 617.00
BASIC RATES : 0.2 LABOUR 6

No.
0154 Nozzel man/ gun man day 738.00

0155* Mason (average) day 709.00
0156* Carpenter (average) day 709.00
0162 Labour for fabrication of uPVC extruded casement/ sliding windows
and doors including drilling holes, fixing of fittings & hardwares, hire
charges of drill machine and electricity charges etc. sqm 485.00
0163 Labour for installation of uPVC extruded casement/ sliding windows
and doors including scaffolding sqm 430.00
*Note:These rates are average of 1st class and 2nd class
catogories. These are for use in the analysis of rates only.
BASIC RATES : 0.2 LABOUR 7

BASIC RATES
0.3 MATERIALS
Note :- These rates are exclusive of GST, contractor’s profit and over heads and carriage etc.

No.
0222 Seam bolts and nuts 6 mm dia and 25 mm long 10 Nos 10.00
0223 Fibre (reinforced by organic fibres and / or inorganic synthetic fibre)
cement corrugated sheet 6 mm thick sqm 225.00
cement close fitting adjustable ridge metre 210.00
cement corrugate serrated adjustable ridge metre 210.00
cement plain wing adjustable ridge metre 210.00
cement unserrated adjustable ridge for hips metre 210.00
cement corrugated apron piece metre 200.00
cement eaves filler piece each 175.00
cement north light curves metre 280.00
cement ventilator curves each 310.00
cement barge boards boards 6 mm thick metre 400.00
cement ridge finial pair 165.00
cement special north light curves each 555.00
cement S type louvers each 260.00
0236 Multi purpose fibre (reinforced by organic fibres and / or inorganic
synthetic fibre) cement board 6 mm thick sqm 210.00
0237 Multi purpose fibre (reinforced by organic fibres and / or inorganic
synthetic fibre) cement board 8 mm thick sqm 220.00
0239 8mm thick heavy duty fiber cement board sqm 300.00
0241 12.5 mm thick Gypsum plaster board sqm 170.00
0242 6 mm thick mulitipurpose cement bonded wood particle board
conforming to IS : 14276 sqm 195.00
0244 Factory made light weight composite non asbestos fibre reinforced
aerated cement sandwitched wall/roof panel (50mm thick). The outer
face on both sides of the panels will be non asbestos fibre cement
0245 Factory made light weight non asbestos fibre reinforced aerated
cement sandwitched wall/roof panel (75mm thick). The outer face on
both sides of the panels will be non asbestos fibre cement board
(minimum 5mm thick) confirming to IS 14862:2000 sqm 789.00
BASIC RATES : 0.3 MATERIALS 8

No.

0303 Cowdung cum 50.00
0304 Bajri cum 1000.00
0305 Bamboo 25 mm dia 2.5 metre long score 400.00
0310 Bitumen emulsion tonne 30099.00
0312 Bitumen grade PMB - 40 tonne 32200.00
0313 Blown type petroleum bitumen of penetration 85/25 of approved quality tonne 34000.00
0317 Premoulded joint filler 12 mm thick sqm 360.00
0318 Bitumen felt fibre base (vegetable or animal):As per IS 7193 Grade I sqm 70.00
0319 Bitumen felt as per IS 7193 Grade II sqm 80.00
0323 Separation Membrane of impermeable plastic sheeting 125 micron thick sqm 12.00
0324 Coal Tar litre 30.00
0325 Blasting powder kg 40.00
0326 Blasting fuse (fuse wire) each 15.00
0328 White face insulating board: 12 mm thick sqm 235.00
0332 Natural colour insulating board: 12 mm thick sqm 210.00
0336 Flame retardant face insulating board: 12 mm thick sqm 320.00
0339 Flame retardant face insulating, Impregnated fibre board 12 mm thick sqm 375.00
0341 Flat pressed 3 layer particle board (medium density) Grade 1, 12 mm thick sqm 288.00
0346 Extra for veneered particle board with Teak veneering on one side and
commercial veneering on other side sqm 230.00
0347 Extra for veneered particle board with Commercial veneering on both
sides sqm 155.00
0348 Extra for veneered particle board with Teak veneering on both sides sqm 500.00
0351 Integral crystalline slurry kg 238.00
0352 Integral crystalline admixture kg 272.00
0353 Crystalline mortar kg 215.00
0354 Integral crystalline dry shake kg 360.00
0355 Swellable type water stop tape metre 365.00
0356 Primer for swellable type water stop tape litre 1540.00
0357 Polymer modified adhesive mortar kg 15.00
0362 Brick bats cum 450.00
0364 Wire brush each 20.00

No.
0365 Soft brush each 20.00

0369 Plastic sheet,1.25 mm thick for dowel bars sqm 25.00
0371 Sealant primer kg 130.00
0373 Cramp Gun metal 25x6x300 mm each 80.00
0374 Pre moulded Joint filler, 25 mm thick for expansion joint. sqm 400.00
0378 Brass butt hinges (light/ordinary type) : 125x70x4 mm 10 Nos 775.00
0380 Brass butt hinges (light/ordinary type) : 75x40x2.5 mm 10 Nos 380.00
0382 Brass butt hinges (heavy type) : 125x85x5.5 mm(0.70 kg) 10 Nos 1309.00
0384 Brass butt hinges (heavy type) :75x65x4.0 mm (weighing not less
than 0.20 kg) 10 Nos 838.00
0385 Brass parliamentary hinges 150x125x27x5 mm 10 Nos 2610.00
0388 Brass parliamentary hinges 75x100x20x3.2 mm 10 Nos 1870.00
0400 Brass tower bolt (barrel type) 250x10 mm each 257.00
0408 Brass handles 125 mm with plate 175x32 mm each 144.00
0411 Brass door latch 300x16x5 mmweighing not less than 0.380 kg each 185.00
0412 Brass door latch 250x16x5 mm weighing not less than 0.350 kg each 175.00
0413 Brass mortice latch and lock 100x65 mm with 6 levers and a pair of
brass lever handles each 400.00
0414 Brass mortice latch 100x65mm with a pair of brass lever handles each 310.00
0417 Brass 150 mm floor door stopper weighing not less than 0.357kg each 160.00

No.
0424 Brass casement stays (straight peg type) 300 mm weighing not less
than 0.33 kg each 126.00
0427 Brass quadrant stays 300 mm each 110.00
0428 Brass fanlight catch 10 Nos 170.00
0429 Brass fanlight pivot 10 Nos 168.00
0430 Brass chain with hook for fan light catch each 36.00
0431 Brass hasps and staples (safety type) 150 mm 10 Nos 740.00
0438 Brass night latch each 610.00
0442 Brass helical spring 150 mm each 290.00
0446 Brass brackets (curtain rods) 20 mm each 45.00
0447 Brass cupboard knob or wardrobe knob 50 mm each 36.00
0454 Stainless steel SS grade 304 , curtain rod 20 mm dia 1.20mm thick metre 125.00
0455 Stainless steel SS grade 304, curtain rod 25 mm dia 1.20mm thick metre 170.00
0456 Stainless steel SS grade 304, brackets ( curtain rod) 20 mm dia
1.20mm thick each 46.00
0457 Stainless steel SS grade 304, brackets ( curtain rod) 25 mm dia
1.20mm thick each 55.00
0458 plastic sleeves for screw each 2.00
0524 Chromium plated Brass butt hinges (heavy) type 75x65x4 mm weighing
not less than 200gms 10 Nos 905.00
0525 Chromium plated Brass butt hinges (light/ordinary) type 125x70x4mm 10 Nos 805.00
0526 Chromium plated Brass butt hinges (light/ordinary) type 100x70x4 mm 10 Nos 690.00
0527 Chromium plated Brass butt hinges (light/ordinary) type 75x40x2.5 mm 10 Nos 421.00
0528 Chromium plated Brass butt hinges (light/ordinary) type 50x40x2.5 mm 10 Nos 180.00
0552 75mm SS fancy handles for kitchen cabinet 10 Nos. 255.00
0553 100mm SS fancy handles for kitchen cabinet 10 Nos 455.00
0554 125mm SS fancy handles for kitchen cabinet 10 Nos 640.00
0555 Chromium plated Brass handles 125 mm with plate 175 x32 mm each 160.00
0556 Chromium plated Brass handles 100 mm with plate 150 x 32 mm each 140.00
0557 Chromium plated Brass handles 75mm with plate 125x32 mm each 125.00
0558 Chromium plated Brass mortice latch and lock 100x65 mm with
6 levers and a pair of brass lever handles each 470.00
0568 Chromium plated brass casement window fastener each 90.00
0569 Chromium plated Brass casement stays (straight peg type) 300 mm
weighing not less than 0.33 kg each 140.00

No.
0583 Chromium plated Brass Night latch each 500.00
0584 Chromium plated Brass Wardrobe Knob 50 mm each 80.00
0590 Chromium plated Brass curtain rod 12 mm dia 1.25mm thick metre 185.00
0593 C.P. Brass Extension Nipple (1/2"x2" size) each 40.00
0594 Bright finished or black enameled mild steel butt hinges 125x65x 2.12 mm 10 Nos 135.00
0641 Bright finished or black enameled mild steel bolts and nuts 50x6 mm each 5.00
0642 Oxidised mild steel butt hinges 125x65x2.12 mm 10 Nos 130.00
0646 Oxidised mild steel parliamentary hinges 150x125x27x2.8 mm 10 Nos 334.00
0650 Oxidised mild steel single acting spring hinges 150 mm each 138.00
0653 Oxidised mild steel double acting spring hinges 150 mm each 157.00
0656 Nickel plated mild steel piano hinges 1 mm thick 35 mm wide metre 44.00
0660 Oxidised mild steel sliding door bolt 300x16 mm each 93.00
0662 Oxidised mild steel door latch 300x20x6 mm each 49.00
0664 Oxidised mild steel tower bolt (barrel type) 250x10 mm each 43.00
0668 Oxidised mild steel handles 125 mm each 20.00

No.
0679 Oxidised mild steel hasps and staples (safety type) 150 mm 10 Nos 128.00
0682 Oxidised mild steel screws 50 mm 100 Nos 76.00
0690 Anodised Aluminium butt hinges 100x63x3.2 mm 10 Nos 270.00
0696 Anodised Aluminium sliding door bolt 300x16 mm each 147.00
0698 Anodised Aluminium tower bolt (barrel type) 300x10 mm 10 Nos 580.00
0703 Anodised Aluminium handles 125 mm with plate 175 x 32 mm 10 Nos 324.00
0705 Anodised Aluminium handles 75mm with plate 125 x 32 mm 10 Nos 231.00
0706 Anodised Aluminium kicking plate 50 cm long 100x3.15 mm each 142.00
0713 Block board construction flush door with teak wood ply on both faces
0717 Block board construction flush door with commercial ply on both faces
0752 Block board construction flush door lipping 25 mm thick sqm of 300.00
door area
0753 Square vision panel in Block board construction flush door not exceeding sqm of
0.10 sqm door area 130.00
0754 Circular vision panel in Block board construction flush door sqm of 135.00
door area
0755 Decorative type louvers in Block board construction flush door sqm of 265.00
door area
0757 Rebate cutting in block board construction flush door sqm of 70.00
door area
No.
0759 Decorative plywood 4 mm sqm 320.00

0763 Glue kg 75.00
0764 Calcium silicate base compound for jointing calcium silicate tiles kg 26.00
0765 Hessian cloth sqm 35.00
0768 Cement Concrete Jali 50 mm thick sqm 400.00
0772 White cement based polymer modified self curing compound in powder
form kg 15.00
0776 Satna lime quintal 370.00
0785 Marble chips up to 4 mm and down size White & black quintal 189.00
0788 Marble chips large size above 4 mm White & black quintal 250.00
0801 Silicon and acrylic emulsion litre 130.00
0802 Acrylic distemper 1st quality , having VOC content less than 50 grams/ litre Kg 36.00
0803 Acrylic emulsion, having VOC content less than 50 grams/ litre litre 94.00
0804 Premium acrylic emulsion of interior grade, having VOC content less
than 50 grams/ litre litre 220.00
0806 Ready mixed pink or grey primer on wood work (hard and soft wood)
having VOC content less than 50 grams/ litre litre 105.00
0808 Water thinnable cement primer for interior wall surface, having VOC
content less than 50 grams/ litre litre 50.00
0809 Exterior primer kg 140.00
0811 Mud (dry) cum 165.00
0816 Ist quality Acrylic distemper(Ready mix) having VOC content less than
50 grams/ litre kg 50.00
0818 Linseed oil (double boiled) litre 200.00
0820 Cement primer litre 80.00
0821 Distemper primer litre 70.00
0823 Pink primer (for wood) litre 105.00
0824 White cement based putty kg 13.00
0831 Floor enamel paint in all shades except green litre 250.00
0834 Synthetic enamel paint in all shades except black or chocolate shade litre 160.00
0836 100% Premium acrylic dirt resistance, Silicone additives exterior paint litre 270.00
0837 Acrylic Exterior Primer litre 100.00

No.
0850 White lead kg 170.00
0863 Putty for wood work kg 30.00
0865 Pig lead kg 130.00
0868 Premixed super white gypsum plaster kg 6.00
0870 Plug each 10.00
0873 Copper pins 6 mm dia 7.5 cm long each 10.00
0874 Black colour dark shade pigment kg 70.00
0875 Red, chocolate, orange, buff or yellow (red oxide of iron) light shade
pigment kg 60.00
0876 Green or blue medium shade pigment kg 56.00
0886 Standard holder bat clamps for sand cast iron or cast iron pipes
0966 Sand Cast iron plain shoe 150 mm dia each 285.00
0967 Copper plate kg 527.00
0969 Pulley 25 mm dia each 48.00
0973 Rolling shutter made of 80x1.25 mm machine rolled laths sqm 1400.00
0974 Top cover for rolling shutters 1.25 mm thick metre 800.00
0975 27.5 cm long wire spring grade No. 2 for rolling shutters each 300.00
0976 Ball bearing for rolling shutters each 260.00
0977 Extra for mechanical devices chain and cranked operation for operating
rolling shutters: exceeding 10.00 sqm and up to 16.80 sqm area of door sqm 800.00
0978 Extra for mechanical devices chain and cranked operation for operating
rolling shutters: exceeding 16.80 sqm area of door sqm 800.00
0979 Royalty for good earth cum 40.00
0980 Royalty for sludge cum 90.00
0993 FY-1860 grade wire strands quintal 5700.00
0994 Standard quality hard board sheet 3 mm thick sqm 135.00
0996 Standard quality hard board sheet 4.5 mm thick sqm 210.00
1002 Mild steel round bar 12 mm dia and below quintal 4500.00
1004 Average rate of Mild steel round bars for reinforcement quintal 4500.00
1006 Mild steel square bars quintal 4500.00

No.
1009 Flats exceeding 10 mm in thickness quintal 4600.00

1010 Mild steel plates quintal 4800.00
1011 Steel glazed door, window/ ventilator, all members viz. F7D, F4B, K11
and K12B etc. kg 54.00
1012 Pregalvanized high tensile steel confirming to IS:277-199 kg 90.00
1015 Mild steel expanded metal 20x60 mm strands 3.25 mm wide 1.60 mm
thick sqm 280.00
1019 Mild steel hooks each 32.00
1020 Mild steel rivets quintal 5000.00
1021 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not less than
7.75 kg/sqm sqm 430.00
1022 Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head
with slots 10 Nos 38.00
1024 Galvanised steel bolts & nuts 10 mm dia and 125 mm long round
head with slots each 9.00
1025 Mild steel bolts 6 mm dia and 25 mm long with hexagonal head 10 Nos 10.00
1027 Erection Bolts ( Minimum 04 nos for each element) each 25.00
1028 Straining bolts each 80.00
1029 Galvanised steel barbed wire of 9.8 kg /100metre quintal 5500.00
1030 Galvanised steel turn buckles each 25.00
1031 Galvanised steel bolts & nuts 10 mm dia and 27 cm long both sides
threaded with 4 galvanised steel nuts each 20.00
1032 Galvanised steel bolts 10 mm dia and 7 cm long with nuts each 6.00
1035 Bolts and nuts above 300 mm in length quintal 5100.00
1036 Iron pintels including welded pin each 37.00
1143 Steel beading 10x10x1.6mm (box type) metre 27.00
1145 Aluminium Plain Strip edging 38x12x3 mm metre 90.00
1149 Glass strip 4 mm thick 40 mm deep metre 20.00
1151 Boundary stone top chisel dressed 15x15x90 cm each 80.00
1154 Through and bond stone 100 Nos 5000.00
1157 Stone for masonry work cum 1100.00
1158 Stone for pitching 15 cm x 22.5 cm cum 600.00
1160 Red sand stone block 10 cudm 79.00
1161 White sand stone block 10 cudm 205.00
1163 White sand stone slab 75 mm thick (un-dressed) sqm 900.00
1164 Red sand stone slab 40 mm thick (un-dressed) sqm 200.00
1168 Kota stone slab 20 mm to 25 mm thick (semi-polished) sqm 280.00
1175 White sand stone slab 45 mm to 50 mm thick (un-dressed) sqm 240.00
1177 Stone grit 6 mm and down size or pea sized gravel cum 800.00

No.
1186 Superior class teak wood such as Dandeli, Balarshah or Malabar in

planks 10 cudm 1100.00
1187 First class teak wood in scantling 10 cudm 880.00
1188 First class teak wood in planks 10 cudm 850.00
1191 Marandi wood in planks 10 cudm 440.00
1192 Marandi wood in scantling 10 cudm 431.00
1197 Second class kail wood in scantling 10 cudm 260.00
1200 Kiln seasoned selected sheesham wood planks 10 cudm 650.00
1201 Precast terrazzo tiles 22 mm thick (light shade) sqm 285.00
1202 Precast terrazzo tiles 22 mm thick (medium shade) sqm 265.00
1203 Precast terrazzo tiles 22 mm thick (dark shade) sqm 245.00
1204 Precast heat resistant terrace tiles (size 300x300 mm) and 20 mm thick sqm 409.00
1207 G.I. Limpet washer 100 Nos 21.00
1210 G.I. plain washer thin 100 Nos 21.00
1211 G.I. plain washer for seam bolts 100 Nos 32.00
1214 Welding by gas plant cm 2.00
1216 Whiting quintal 600.00
1217 GI Wire mesh 100x100 mm kg 75.00
1218 Shear stud each 50.00
1219 Wire nails kilogram 58.00
1220 Wire mesh (rabbit) sqm 42.00
1221 20 mm dia holding down bolts quintal 6100.00
1222 Mild steel sheets with bolts and nuts to rest on pintels each 120.00
1223 Steel weld mesh sqm 150.00
1224 Hard drawn steel wire quintal 4800.00
1225 Mild steel flat strap fitting quintal 4120.00
1227 Chequered terrazzo tiles 22 mm thick (light shade) sqm 275.00
1228 Chequered terrazzo tiles 22 mm thick (medium shade) sqm 300.00
1229 Chequered terrazzo tiles 22 mm thick (dark shade) sqm 260.00
1231 Extra for selected planks of second class teakwood 10 cudm 150.00
1234 Aluminium Plain Strip edging 57x12x3 mm metre 135.00
1237 Cutting marble or sand stone slab up to 50 mm thick by mechanical
device metre 10.00
1238 Extra for selected planks of first class teakwood 10 cudm 150.00
1239 18 mm thick Flamed finish granite stone slab sqm 1000.00
1240 18 mm thick Italian Marble stone slab, Perlato (slab area up to 0.5 sqm). sqm 3209.00
1242 Glass mossaic tiles (20 mm x 20 mm x 4 mm) sqm 2049.00

No.
1243 Tile fixing chemical adhesive kg 8.70

1244 Cement Polymer Grout Compound kg 16.00
1245 Acid for cleaning tiles litre 18.00
1246 Silicon based Joint Sealant for Tiles kg 160.00
1247 Rubber base Adhesive kg 223.00
1248 Epoxy based sealing Compound kg 535.00
1249 Acrylic based sealing compound kg 500.00
1250 Non woven reinforcement Tape metre 0.14
1251 M-60 grade cemetitious grout (Non Shrink) kg 28.00
1252 Cementitious polymer base adhesive confirming to EOTA ETAG 004
1253 Polypropylene mechanical fastener with plastic pin confirming to
EOTA ETAG 014 (European Technical Approval) having dia 10mm &
L=200mm each 30.00
1254 Moisture cure Polyurethane Foam 750 ml 600.00
1255 PVC Corner Bead of size 25mmx25mm fixed with glass fibre mesh
(100mm x 100mm) metre 90.00
1256 Cementitious polymer base coat confirming to EOTA ETAG 004
1257 Fiberglass mesh with alkali-resistant coating having mass per unit
area ?145 g/m2, mesh size: 3.9x4.0 mm ±10% sqm 75.00
1304 Surface box for stop cock each 125.00
1305 Surface box for sluice valve each 210.00
1307 Surface box for water meter each 250.00
1309 C.I. bracket for wash basin and sinks pair 88.00
1313 8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with
S.S. tringular plate for Eureopean type W.C. each 200.00
1316 50mmx50mm hardwood plug each 75.00
1350 Mosquito proof coupling of approved design each 30.00
1352 C.I. cover and frame 300x300 mm inside each 477.00
1353 C.I. cover without frame 300x300 mm inside i/c cover of 4.50 kg each 477.00
1354 Rectangular cover 455x610 mm with frame (low duty) each 1400.00
1355 Rectangular cover 455x610 mm without frame (low duty) each 910.00
1356 500 mm dia cover with frame (medium duty) each 4400.00
1357 500 mm dia cover without frame (medium duty) each 2300.00

No.

1362 C.l. mouth, brass ferrule 25 mm dia each 220.00
1369 S.C.I. gully or nahani grating 100 mm dia each 25.00
1392 Mirror of superior make glass 60x45 cm each 400.00
1396 Vitreous china pedestal for wash basin each 900.00
1397 Pig lead kg 176.00
1464 S & S.C.I. standard specials upto 300 mm dia (heavy class) quintal 3600.00
1466 S & S.C.I. standard specials over 300 mm dia (heavy class) quintal 3700.00
1468 Flanged C.I. standard specials upto 300 mm dia (heavy class) quintal 5500.00
1470 Flanged C.I. standard specials over 300 mm dia (heavy class) quintal 5500.00
1472 Casing pipe 100 mm dia metre 335.00
single stall each 270.00
double stall each 400.00
range of three stall each 520.00
range of four stall each 600.00
1540 Flush pipe and spreaders G.l. for single set of one squatting plate urinal each 175.00
1541 Flush pipe and spreaders G.l. for range of two squatting plates urinal each 250.00
1542 Flush pipe and spreaders G.l. for range of three squatting plates urinal each 300.00
1543 Flush pipe and spreaders G.l. for range of four squatting plates urinal each 390.00

No.

1614 G.I. inlet connection each 60.00
100 mm dia each 1135.00
150 mm dia each 1750.00
1636 S.C.I. double equal junctions 75x75x75x75 mm dia with access door each 500.00
1637 S.C.I. double equal junctions 100x100x100x100 mm dia with access
door each 715.00
1649 Polyethylene water storage tank with cover and suitable locking
arrangement per litre 5.50
1653 Sand cast iron S&S plain single unequal junctions: 100x100x75 mm dia each 494.00
1656 Sand cast iron S&S single unequal junctions: 100x100x75 mm dia with
access door each 550.00
1659 Sand cast iron S&S plain double unequal junctions: 100x100x75x
1662 Sand cast iron S&S double unequal junctions: 100x100x75x75 mm dia
with access door each 700.00
1672 S.C.I. double equal invert branch of required degree 75x75x75x75 mm dia each 410.00
1673 S.C.I. double equal invert branch of required degree 100x100x100x
1674 S.C.I. single unequal invert branch of required degree 100x100x75 mm dia each 495.00

No.
1677 S.C.I. double unequal invert branch of required degree 100x100x75x

1693 S.C.I. hand pump each 670.00

No.

1863 Fire clay kitchen sink: 600x450x250 mm each 1283.00
1875 White plastic seat (solid) with lid C.P. brass hinges and rubber buffers each 400.00
1876 Black plastic seat (solid) with lid C.P. brass hinges and rubber buffers each 310.00
1880 Dismenteled P or S trap scrap (approx wt 2kg) kg 22.00
1882 Strainer brass 40 mm dia 1.5 metre long each 600.00
1885 15 mm C.P. brass tap each 207.00
1889 C.P. brass toilet paper holder of standard size each 225.00
1890 Centrifugally SCI(spun) S & S P or S trap each 300.00
1895 C.P. brass trap 40 mm dia each 300.00
1896 100 mm S.C.I. trap with vent heel each 320.00
1913 Vitreous china lipped front urinal each 460.00
1915 Vitreous china squatting plate urinal each 1053.00
1926 20 mm dia Gunmetal gate valve with wheel each 325.00

No.

1955 Vitreous china pedestal type water closet each 1000.00
1965 White vitreous china dual purpose closet (Anglo Indian W.C.) suitable
for use as squatting pan or European type water closet as per
manufacturer's specifications each 2500.00
1966 Floor mounted white vitrous china double trap syphonic WC with
10 litre cistern and all fittings & fixtures,seat cover etc each 9500.00
1984 Common burnt clay F.P.S. bricks tile class designation 10 1000 Nos 4500.00
1986 Common burnt clay modular bricks class designation 12.5 1000 Nos 5000.00
2207 Carriage of Brick tiles 1000 Nos 166.03

No.

2241 Carriage of Good earth cum 129.71
2242 Carriage of Dump manure by mechanical transport upto 5 km lead cum 112.79
2261 Carriage of Fine sand (1 Part badarpur sand : 2 parts jamuna sand) cum 103.77
2262 Carriage of Flyash cum 103.77
2265 Carriage of Moorum cum 103.77
2266 Carriage of Surkhi cum 103.77
2268 Carriage of Marble dust and/or marble chips cum 103.77
2273 Carriage of A.C.sheet and accessories tonne 92.24
2299 Carriage of R.C.C. pipes 450 & 500 mm dia 100 metre 2520.19
2303 Carriage of R.C.C. pipes 600,700,750 & 800 mm dia 100 metre 3780.28
2308 Carriage of Plaster of paris tonne 92.24
2309 Carriage of Cast Iron fittings tonne 92.24
2311 Carriage of Red bajri cum 103.77
2314 Carriage of Barbed wire tonne 92.24
2317 Carriage of Sludge cum 112.79
2329 Carriage of Spun iron S & S pipes 600mm dia 100 metre 3780.28
2330 Carriage of C.I. pipes 500 mm dia 100 metre 2520.19
2336 Carriage of R.C.C. pipe above 1200 mm dia and upto 1800 mm dia 100 metre 7560.57
2341 Carriage of Pig lead tonne 92.24

No.

2391 Strips-Aluminium fluted 3.15 mm thick and 150 mm wide metre 278.00
2392 Strips Aluminium fluted 3.15 mm thick and 200 mm wide metre 370.00
2393 1 mm thick Stainless Steel Cover plate grade 304 kg 275.00
2394 Coupler 16 mm dia each 30.00
2399 Complete Roof Joint of 100 mm metre 2800.00
2402 Epoxy adhesive kg 150.00
2403 Floor Joint of 100 mm metre 3100.00
2406 Float glass panes of nominal thickness 4 mm (weight not less than
10 kg/sqm) sqm 300.00
12.50 kg/sqm) sqm 500.00
20.00 kg/sqm) sqm 610.00
2409 Wall Joint of 100 mm metre 2400.00
2412 Ply wood 5 ply with commercial ply on both faces 6 mm thick sqm 300.00
2413 12 mm commercial ply sqm 500.00
2414 18 mm thick block board with commercial ply veneering on both side sqm 760.00
2415 21mm thick clear toughened Laminated glass for fins with holes sqm 6000.00
2447 Hollock ballies 125 mm diameter metre 35.00
2449 Oxidised mild steel pull bolt lock (locking bolt) of size 85 mm x
42 mm with screws, bolts, nuts and washers complete each 60.00
2451 Brass cupboard lock 6 levers of approved quality, 40 mm size each 55.00

No.
2455 Brass hanging type door stopper 150 mm each 75.00
2456 Hydraulic door closer bottle type M.S. body with necessary accessories
and screws complete each 673.00
2459 Anodised Aluminium hanging type door stopper each 19.00
2464 Anodised Aluminium pull bolt lock (locking bolt) of size 85 mm x
2465 Anodised Aluminium Casement stay 250 mm each 32.00
2467 Chromium plated Brass pull bolt lock (locking bolt) of size 85 mm x
2468 Nickled Chromium Brass cupboard lock 40 mm size each 60.00
2480 Ply wood 5 ply with teak ply on both faces 9 mm thick sqm 850.00
2481 Ply wood 5 ply with teak ply on one face and commercial ply on
another face 9 mm thick sqm 870.00
2483 Ply wood 7 ply with teak ply on one face and commercial ply on another
face 9 mm thick sqm 950.00
2484 Pre-laminated with decorative lamination on both side exterior
Grade-I MDF Board 12 mm thick confirming to IS:14587 sqm 460.00
2486 Pre-laminated with decorative lamination one side and other side
balancing lamination exterior Grade-I MDF Board 25 mm thick
confirming to IS: 14587 sqm 860.00
confirming to IS:14587 sqm 430.00
confirming to IS:14587 sqm 565.00
2489 PVC edge bending tape 2.00 mm thick metre 20.00
2491 Pre laminated both side solid foam uPVC profile (45x20mm) metre 130.00
2492 Solid foam uPVC sheet 20mm thick pre laminated on both side sqm 2090.00
2493 PVC edge beading metre 31.00
2494 Expandable fastner with plastic sleeve each 5.00
2500 Extra for selected planks of second class deodar wood 10 cudm 110.00
2504 Kiln seasoning of timber cum 750.00
2505 Hollock wood in planks 10 cudm 390.00
2506 Carben Steel galvanised (min 5 micron) dash fastner (min 5 micron)
of 10 mm dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10mm x
60 mm 10 Nos 260.00
80 mm 10 Nos 300.00

No.
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm
x 120 mm 10 Nos 365.00
140 mm 10 Nos 450.00
160 mm 10 Nos 575.00
2602 Common burnt clay F.P.S. (non modular) bricks class designation 7.5 1000 Nos 4500.00
2603 Common burnt clay F.P.S. (non modular) bricks class designation 5.0 1000 Nos 4000.00
2604 Weather/structural non sag elastomeric PU sealant (600ml Sausage)
for joints in RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum/ Alluminium
work complying to ASTM C920, DIN 18540-F & ISO 11600 incl all
taxes each 532.00
2605 Structural sealant - 6 mm x 12 mm metre 30.00
2606 Spacer tape 6.4 mm thick x 6 mm wide metre 20.00
2607 Weather Sealant - Non Staining (600 ml) each 325.00
2608 Weather Sealant - Normal (300 ml) each 98.00
2609 MS Brackets/Aluminium Alloy Brackets kg 100.00
2610 Silicon Gasket in Kg (Above 50 g / m) kg 465.00
2611 EPDM Gasket in Kg (Above 60 g / m) kg 150.00
2612 Anchor Fastner - M10 each 10.00
2613 SS Bolt with washer of different sizes for structural glazing / ACP
Cladding each 35.00
2614 SS Screws of sizes for structural glazing / ACP Cladding each 3.00
2615 Protective Tape metre 20.00
2616 GI flashing - 1.2 mm Thick kg 59.00
2617 6 mm thick High performance glass sqm 1000.00
2618 6 mm thick clear heat strengthened glass sqm 650.00
2619 6 mm thick clear heat strengthened glass each 128.00
2620 ARMS GS HD - Top Hung -20"- Type P- Couple pair 1350.00
2621 Connection Block for vision glass panel each 35.00
2622 Curtain wall striker for vision glass panel each 85.00
2623 Adjustable Fastening Pawl for vision glass panel each 35.00
2624 Corner drive for vision glass panel each 255.00
2625 Top wedge Block for vision glass panel each 120.00
2626 Glass wool of denisity @ 48 Kg / cum with black glass tissue (BGT) sqm 250.00
2627 SS Screws - # 8 x 19 each 6.00
2628 Weather Sealant - DC 789 cartridge 120.00
2629 Cement Board sqm 235.00
2630 Baker rod metre 5.00
2631 4 mm thick ACP sqm 1100.00
2632 Fire Stop metre 480.00
2634 GI/Aluminium Sheet (0.8 mm thick) kg 55.00
2635 GI Screws of gauge 10, length 25 mm for fixing cement fibre board to
C section each 3.00

No.
2636 GI Screws of gauge 10, length 45 mm for fixing cement fibre board to
C section each 3.00
2637 Vapour barrier sqm 175.00
2640 Glass panes of required thickness having 120 minutes of fire
resistance both integrity and radiation control (EI 120) and minimum
20 minutes of insulation (EI 20) sqm 25000.00
2641 G.I U beading of 1.6 mm thick G.I sheet with ceramic tape. metre 245.00
2642 Ceramic tape 5 x20 mm size metre 410.00
2708 Truf Paver (500 x 500 x 40 mm) sqm 500.00
2709 Ceremic Tiles Pieces for Crazy Flooring quintal 135.00
2710 White marble makrana second quality plain veined stone pieces for
crazy flooring quintal 150.00
2711 FS800H Grade Flooring Panel (Size 600 mm x600 mm x32 mm) each 750.00
2712 Zinc Electroplated Pedestals - 300 mm each 140.00
2714 Zinc Electroplated Tube Stinger each 66.00
2715 Machine Screw for Fixing each 2.00
2750 8 mm thick granite stone tiles (mirror polished of all shades) sqm 700.00
2751 8 mm thick marble tiles (polished) Raj Nagar sqm 400.00
2903 Stone chippings/ screenings 4.75 mm nominal size cum 1400.00
2904 Stone chippings/ screenings 150 micron nominal size cum 1400.00
2910 Stone chippings/ screenings 12.5/ 13.2 mm nominal size cum 1150.00
2914 Solvent kg 25.00
2916 Paving Asphalt VG 10 of approved quality tonne 24000.00
3004 Stone ware spouts 100 mm dia 60 cm long each 40.00
3050 Galvanised steel corrugated sheets quintal 5600.00
3213 Vitreous china Surgeon type wash basin of size 660x460 mm each 1000.00
3228 600x120 mm glass shelf with anodised aluminium angle frame,
C.P. brass brackets and guard rail of standard size each 250.00
3327 15 mm Battery Based Sensor Pillar Cock each 5800.00

No.
3617 C.P. Brass union 40mm dia each 200.00

3620 C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres long:
100 mm dia each 1200.00
3621 C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres long:
3644 S.C.I. S&S single equal junctions with access door 100x100x 100 mm each 495.00
3645 S.C.I. S&S single equal junctions with access door 75x75x75 mm each 373.00
3654 S.C.I. S&S double equal junctions with access door 100x100x100x
100 mm each 615.00
3655 S.C.I. S&S double equal junctions with access door 75x75x75x75 mm each 480.00
3660 S.C.I. S&S single unequal junctions 100x100x75 mm each 570.00
3664 S.C.I. S&S single unequal junctions with access door 100x100x75 mm each 640.00
3670 S.C.I. S&S double unequal junctions 100x100x75x75 mm each 800.00
3674 S.C.I. S&S double unequal junctions with access door 100x100x75x
75 mm each 850.00
3682 S.C.I. S&S single equal invert branch of required degree 75x75x 75 mm dia each 323.00
100x100 mm dia each 530.00
3686 S.C.I. S&S double equal invert branch of required degree 75x75x75x
3690 S.C.I. S&S single unequal invert branch of required degree 100x100x
3695 S.C.I. S&S double unequal invert branch of required degree 100x100x

No.
3749 Vitreous china toilet paper holder of standard size each 100.00
3860 560 mm dia cover with frame (Heavy duty) each 9000.00
3861 560 mm dia cover without frame (Heavy duty) each 5000.00
3991 Galvanized iron (1.6 ± 0.2 mm) thick reinforcement for small series
casement window/door frame, sash, mullion & small series sliding
window frame metre 66.00
3992 Galvanized iron (1.6 ± 0.2 mm) thick reinforcement for big series
casement window/door frame, sash, mullion, big & small series
sliding window frame metre 71.00
casement door sash metre 97.00
sliding window / door sash metre 86.00
3995 G.I fasteners 100 x 8 mm each 14.00
4001 Stainless steel (Grade-304)hollow section round/square tubes kg 220.00
4002 Stainless steel bolts/square bar and plates kg 115.00
4006 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "B" metre 190.00
4007 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "C" metre 210.00
4008 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "E" metre 240.00
4010 Mild steel tubes hot finished seamless type kg 67.00
4011 Mild steel tubes electric resistant or induction butt welded kg 47.00
4012 Circular C.I. Box for ceiling fan internal dia 140 mm, 73 mm height,
toplid of 1.5mm thick MS sheet each 52.00
4201 Aluminium primer litre 110.00
4204 Hydrochloric acid kg 33.00
4205 Copper chloride kg 270.00
4206 Copper nitrate kg 210.00
4207 Ammonium chloride kg 20.00
5050 SS pipe 304 grades with press fit technology as per JIS 3448 Standard
48.60 mm outer dia metre 650.00
5743 Coloured inter locking C.C. paver Block sqm 480.00
6001 White marble slab Makrana second quality plain veined 18 mm thick sqm 1430.00
6007 Pink marble slab plain 18 mm thick sqm 645.00
6010 Udaypur green marble slab plain 18 mm thick sqm 620.00
6019 Black Zebra marble slab plain 18 mm thick sqm 900.00
7001 Brass 100mm mortice latch and lock with 6 levers without pair of handles each 210.00
7003 Pair of Anodised Aluminium lever handles for 100 mm mortice latch
and lock each 215.00
7005 Vitreous china 10 litres low level cistern without fittings each 715.00
7006 Vitreous china 10 litres low level cistern with fittings each 1240.00
7008 F.P.S. (non modular) clay fly ash bricks class designation 7.5 1000 Nos 4800.00
7009 12.5 mm thick tapered edge plain Gypsum plaster borad Confirming to
IS 2095 (Part- I) : 2011 sqm 155.00

No.
7010 Galvanised Steel ceiling section (size 80x26x0.50 mm) metre 46.00
7011 Galvanised Steel perimetre Channel (Size 20x27x30x0.50 mm) metre 22.00
7012 Galvanised Steel intermediate Channel (Size 15x45x15x0.90 mm) metre 38.00
7013 Galvanised Steel angle hanger (Celling angle) (Size 25x10x0.50 mm) metre 12.00
7014 Galvanised Steel connecting clips (2.64 mm dia and 230 mm long
GI wire) each 4.00
7015 Galvanised Steel soffit cleat (Size 27x37x25x0.60 mm) each 3.00
7016 Joint filler kg 26.00
7017 Joint finisher kg 23.00
7018 Joint tape roll roll 100.00
7020 All drive screws (for gypsum board) 100 Nos 58.00
7021 Primer (for gypsum board) litre 85.00
7022 Chlorpyriphos 20% E.C. / Lindane 20% E.C. litre 150.00
7023 Chromium plated brackets (curtain rods) each 7.00
7024 Acid Proof cement tonne 7800.00
7025 Self tapping pan head nickel coated mild steel screws of size 13 x
3.2 mm 1000 Nos 525.00
7026 Fibre joint tape 50 mm wide (90 metre) roll each roll 165.00
7027 M.S. Butt hinges 125x90x4 mm 10 Nos 105.00
7028 12.5 mm thick Fully Perforated gypsum board sqm 410.00
7029 Galvanised wire mesh of average width of aperture 1.4 mm and nominal
dia of wire 0.63 mm sqm 250.00
7031 12.5 mm thick tapered edge moisture resistant plain Gypsum plaster
board confirming to IS 2095 (Part- I) : 2011 sqm 275.00
7032 Frosted glass sheet of nominal thickness 4 mm (weighing not less than
10 kg/sqm) sqm 460.00
7033 Nickel plated M.S. pipe 25 mm dia metre 76.00
7035 Nickel plated M.S. Brackets for curtain rod 20 mm each 7.00
7036 Nickel plated M.S - Brackets for curtain rod 25 mm each 8.00
7042 Mild steel conduit pipe (heavy type) ISI marked-20 mm dia metre 42.00
7044 Rolling shutters of 80x0.90 mm laths sqm 1300.00
7046 Top cover of Rolling shutters 0.90 mm thick metre 450.00
7049 Teak wood lipping of size 25x3 mm in pelmets metre 14.00
7050 PU Primer sqm 60.00
7051 40 mm (average) PU spray having 40-45 kg/m3 density sqm 400.00
7052 GI wire netting 3/4" x 24 G sqm 26.00
7053 400 G polythene sheet sqm 14.00
7055 Flat pressed 3 layer and graded particle board (medium density) Grade
1 conforming to IS : 3087 - 18 mm thick sqm 480.00
7056 Aluminium tee channel (heavy duty) with rollers and stop end metre 100.00
7059 Aluminium hanging floor door stopper with twin rubber & stopper each 40.00
7060 Hydraulic door closer tubular type Aluminium section body each 560.00

No.
7063 Oxidised M.S.casement stay (straight peg type) 300 mm not less than
0.33 kg each 35.00
7064 Oxidised M.S.casement stay (straight peg type) 250 mm not less than
0.28 kg each 30.00
7065 Oxidised M.S. casement stay (straight peg type) 200 mm not less than
0.24 kg each 25.00
7068 Extra for providing grilled rolling shutters with 8 mm dia M.S. rod sqm 500.00
7070 Chequered precast cement concrete tiles 22 mm thick using marble
chips of size 6mm - Light shade using white cement sqm 400.00
7071 White marble Raj Nagar plain 18 mm thick upto 0.50 sqm area sqm 600.00
7072 Wall mounted water closet of size 780 x 370x690 mm each 6000.00
7073 Adjustable Vitreous China Cistern with fittings of flushing capacity
3 litre/ 6litre 9adjustibla to 4 litre/8litre) each 1900.00
7074 White Vetrious China Waterless Urinal of size 600x330x315 mm each 9650.00
7075 Cistern with fittings for Waterless Urinal each 2290.00
7076 Battery based infrared sensor operated white Vitreous Urinal of aprox.
size 610x390x370 mm each 4500.00
7077 Acid and alkali resistant tiles 300x300 mm size, 10 mm thick 10 Nos 520.00
7087 S.C.I. Tee 150 mm each 570.00
7090 Expanded polystyrene type N- Normal 50 mm thick sqm 125.00
7091 Expanded polystyrene type - SE 50 mm thick sqm 150.00
7095 Stainless steel kitchen sink - with drain board 510 x 1040 mm bowl
depth 250 mm each 2480.00
7098 Stainless steel kitchen sink - with drain board 510x1040 mm bowl
7101 Stainless steel kitchen sink - without drain board 610x510 mm bowl
7104 Coloured Orissa pattern W.C. pan 580x440 mm each 1830.00
7105 Coloured Pedestal type W.C. pan 580x440 mm (European type) each 860.00
7106 Coloured Vitreous china 10 lit. low level cistern each 1050.00
7107 Coloured (other than black) solid P.V.C. seat in European W.C. pan each 390.00
7112 Circular shape 450 mm dia Mirror with Plastic moulded frame each 430.00
7114 Oval shape 450x350 mm (outer dimensions) Mirror with Plastic
moulded frame each 340.00
7116 Hard board 6 mm thick sqm 115.00
7117 Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with
length not less than 700 mm i/c PVC waste fittings each 25.00
7118 Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with
length not less than 700 mm i/c PVC waste fittings each 33.00
7119 Flexible (coil shaped) PVC waste pipe for sink and wash basin 32mm dia
7120 Flexible (coil shaped) PVC waste pipe for sink and wash basin 40
mm dia with length not less than 700 mm i/c PVC waste fittings each 35.00

No.
7121 Bottle Trap each 620.00

7122 CP Brass Single lever telephonic wall mixer of approved make each 4500.00
7123 Coloured High density polyethylene / poly propylene 10 lit. (full flush)
capacity controlled low level flushing cistern with fittings each 550.00
7126 White Vitreous china 10 litre (full flush) capacity controlled low level
7127 Coloured Vitreous china 10 litre (full flush) capacity controlled low level
7130 Rectangular shape 600x450 mm precast R.C.C. manhole cover with
frame - L.D. - 2.5 each 675.00
7131 Square shape 450x450 mm precast R.C.C. manhole cover with frame -
L.D. - 2.5 each 575.00
7132 Circular shape 450 mm dia precast R.C.C. manhole cover with frame -
L.D. - 2.5 each 575.00
7133 Rectangular shape 500x500 mm precast R.C.C. manhole cover with
frame - M.D. - 10 each 670.00
7134 Circular shape 500 mm dia precast R.C.C. manhole cover with frame-
M.D.-10 each 575.00
H.D. - 20 each 880.00
E.H.D. - 35 each 1170.00
7137 Factory made 35 mm thick shutters with laminated veneer lumber
styles & rails as per TADS 15:1995 and panels of 12 mm thick plain
type-I, medium density flat pressed three layer, graded particle board
(FPT-I) as per IS:3087 bonded with BWP type synthetic resin adhesive,
as per IS:848 sqm 1620.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick both
sides prelaminated type-I, medium density flat pressed three layer,
graded particle board (FPT-I) as per IS:3087 bonded with BWP type
synthetic resin adhesive, as per IS:848 sqm 1720.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick one
side prelaminated type-I, and other side balancing lamination,
medium density flat pressed three layer, graded particle board (FPT-
I) as per IS:3087 bonded with BWP type synthetic resin adhesive, as
per IS:848 sqm 1910.00
styles & rails as per TADS 15:1995 and panels of sheet glass using
10 kg/ sqm glass panes sqm 1620.00
styles & rails as per TADS 15:1995 and panels of galvanised wire
gauge with average width of aperture 1.4 mm in both directions with
wire of dia 0.63 mm sqm 1620.00
gauge with average width of aperture 1.4 mm in both directions with
wire of dia 0.63 mm sqm 1430.00
7157 Laminated veneer lumber confirming to TADS 15:1995 manufactured
in factory in frames of doors, windows 10 cudm 700.00

No.
7178 Chemical ASTMC-type I kg 105.00

7181 C.I. pile shoe kg 48.00
7182 M.S. clamps for pile shoe of 35 kg per pile kg 43.00
7183 Bentonite of 35 kg per pile tonne 2960.00
7184 Oxidised M.S. safety chain (weighing not less than 450 gms) for door each 57.00
7187 C.I. grating 150 mm dia, weighing not less than 440 gm each 27.00
7188 U-PVC pipes (working pressure 4 kg / cm²) Single socketed pipe
75 mm dia metre 70.00
7190 U-PVC pipes (working pressure 4 kg / cm²) Rubber (Seal) Ring
75 mm dia each 8.00
7192 uPVC coupler for UPVC drainage pipes 75 mm each 18.00
7194 uPVC pushfit coupler (single) 75 mm thick each 18.00
7196 uPVC single equal Tee (without door) 75x75x75 mm each 46.00
7198 uPVC single equal Tee (with door) 75x75x75 mm each 59.00
7208 UPVC bend 87.5° 75 mm bend each 35.00
7212 UPVC plain shoe 75 mm bend each 27.00
7214 UPVC pipe clip 75 mm bend each 15.00
7231 Resin Bonded Glass wool 16 kg/m³ : 50 mm thick sqm 100.00
7233 Fibre glass tissue reinforcement Type II Grade i sqm 82.00
7236 Precast chequered cement tiles 22 mm thick Dark shade using ordinary
cement sqm 225.00
7237 Precast chequered cement tiles 22 mm thick medium shade using
50% white cement 50% ordinary cement sqm 335.00
7238 High Albedo paint kg 230.00
7239 Epoxy paint litre 230.00
7240 Fire retardant paint litre 260.00
7241 Melamine polish litre 280.00
7244 Table rubbed polished stone 18 mm thick (75x50cm) Agaria Marble
stone - 18 mm thick sqm 1620.00
7245 Table rubbed polished stone 18mm thick (75x50cm) Granite stone-
(Part-IV) including installation of loading platform and preparation of
pile head or construction of test cap and dismantling of test cap after
test etc. complete as per specification and up to 50 tonne capacity
pile per test 40000.00
test etc. complete as per specification & above 50 tonne and up to
100 tonne per test 45000.00

No.

test etc. complete as per specification & group of two or more up to
50 tonne per test 50000.00
7249 Cyclic vertical load testing of piles in accordance with IS : 2911 (Part-
IV) including preparation of pile head etc. for Single pile up to 50
tonne capacity per test 15000.00
IV) including preparation of pile head etc. for Single pile above 50
tonne capacity pile and up to 100 tonne capacity pile per test 23000.00
IV) including preparation of pile head etc. for Group of two piles up to
50 tonne capacity each per test 29500.00
7252 Lateral load testing of single pile in accordance with IS : 2911 part -IV
for determining safe allowable lateral load on pile up to 50 tonne
capacity per test 15000.00
7253 Lateral load testing of single pile in accordance with IS : 2911 part -IV
for determining safe allowable lateral load on pile above 50 tonne
capacity per test 23600.00
7255 Road marking paint (spirit based) litre 115.00
7256 Superior quality road marking paint (water based) litre 135.00
7257 C.P. Brass bibcock 15 mm each 290.00
7258 C.P. Brass long nose bibcock 15 mm each 430.00
7259 C.P. Brass long body bibcock 15 mm each 385.00
7260 C.P. Brass stop cock (concealed) 15 mm each 430.00
7261 C.P. Brass angle valve 15 mm each 375.00
7266 Pressed clay tiles 20mm thick 250x250 mm size 1000 Nos 8600.00
7267 Plain ceiling tiles (BWP type phenol formaldehyde synthetic resin
bonded) (600x600x12 mm) each 115.00
7268 Semi perforated ceiling tiles (600x600x12 mm) each 107.00
7269 25 mm thick particle board sqm 460.00
7270 30 mm thick prelaminated flush door shutter sqm 810.00
7271 Second class teak wood lipping 25 mm wide x 12 mm thick metre 29.00
7272 25 mm thick melamine faced prelaminated three layer particle board sqm 900.00
7273 Resin Bonded Rockwool 48 kg/m3 sqm 120.00
7274 Glass wool 50 mm thick sqm 238.00
7280 Waste plastic additive tonne 40000.00
7281 Chemical ASTMC-type II kg 165.00
7297 Granite of any colour, 18 mm thick (slab area above 0.50 sqm) sqm 1800.00
7307 For flush door shutters Extra for providing teak veneering on one side
instead of commercial veneering sqm 330.00
7309 Paving Asphalt of grade VG-30 of approved quality tonne 39570.00
7312 Expandable fastener with plastic sleeve and M.S. screws : 25 mm long each 10.00
7315 Expandable fastener with plastic sleeve and M.S. screws. 50 mm long each 14.00

No.

7319 Wall form panel 1250x500 mm each 860.00
7320 Tie bolt 12 mm dia 100 mm length each 38.00
7324 Spring coil 12 mm each 15.00
7325 Plastic cone 12 mm dia each 17.00
7326 Corner angle 45x45x5 mm 1.50 m long each 240.00
7327 100 mm channel shoulder 2.5 m long each 910.00
7328 Double clip (bridge clip) each 76.00
7329 Single clip each 59.00
7330 M.S. tube 40 mm dia metre 215.00
7333 Column clamp 450x1070 mm each 965.00
7334 Prop 2 m ( 2-3.5 m) each 635.00
7335 Binding wire kg 46.00
7336 Lock Bar (E 250) - 10 thick MS Plate kg 76.00
7338 Gun metal cramp kg 315.00
7339 Stainless steel cramp kg 290.00
7340 Stainless steel pin kg 182.00
7342 Adjustable span ESO+SI (2.35-3.40) each 1480.00
7343 Adjustable telescopic prop 3 m (2.02-3.75 m) each 955.00
7344 Beam clamp 300-380 mm (450-1070 mm) each set 355.00
7345 Prop 4 m each 910.00
7347 Cadmium plated full threaded steel screws (30x4 mm dia) 100 Nos 27.00
7348 Aluminium washer 2 mm thick 15 mm dia 100 Nos 10.00
7349 12 mm M.S. 'U' beading metre 14.00
7354 Plastic encapsulated M.S. foot rest 30x20x15 cm each 110.00
7358 Flushing Cistern P.V.C. 10 litre capacity (low level) (White) (with fittings,
accessories and flush pipe) each 575.00
7363 15 mm C.P. brass tap with elbow operation lever each 430.00
7364 White glazed fire clay draining board 600x450x25 mm each 525.00
7366 Glass reinforced Gypsum (GRG) plaster board 12.5 mm thick confirming
to IS 2095 (Part- 3) : 1996 sqm 240.00
7367 Galvanised M.S. sheet 0.5 mm thick pressed channel section of size
50x32 mm metre 57.00
7368 GFRG Panel of 124 mm thick sqm 847.46
7369 Galvanised M.S. sheet 0.50 mm thick pressed stud : 48x34x36 mm metre 71.00
7375 G.I. flush pipe and C.P. brass spreader including C.P. connecting pipe
Single lipped urinal each 445.00
Range of two lipped urinals each 765.00
7377 G.i. flush pipe and C.P. brass spreader including C.P. connecting pipe
Range of three lipped urinals each 1050.00
Range of four lipped urinals each 1430.00

No.
7379 White vitreous china clay half stall urinal flat back 580x380x350 mm or
angle back 450x375x350 mm with waste fittings as per IS:2556 each 865.00
7380 Precast R.C.C. grating with frame 500x450 mm horizontal grating each 620.00
7381 Precast R.C.C. grating with frame 450x100 mm vertical grating each 235.00
7382 Bitumen emulsion rapid setting (R.S.) confirming to IS : 8887 tonne 19000.00
7383 12 mm dia 50 mm long wedge type expanded zinc alloy dash fastener each 7.00
7385 3 mm thick translucent white acrylic plastic sheet sqm 550.00
7386 12 mm thick particle board ceiling tile sqm 110.00
7393 Polyester powder coating 50 microns on aluminium sections kg 67.00
7394 Double action hydraulic floor spring with stainless steel cover plate each 1500.00
7395 6 mm dia G.I. adjustable hangers including clips (up to 1.2 m length) each 20.00
7396 Double action hydraulic floor spring with brass cover plate each 1620.00
7400 15 mm PTMT bib cock each 71.00
7401 15 mm PTMT bib cock with flange (fancy) each 105.00
7402 15 mm PTMT bib cock long body with flange each 116.00
7403 15 mm dia PTMT stop cock (male thread) each 71.00
7405 20 mm dia PTMT stop cock each 97.00
7407 PTMT push cock 15 mm dia each 62.00
7408 PTMT push cock 12 mm dia 20 mm BSP each 57.00
7409 PTMT grating 100 mm dia each 20.00
7410 PTMT Pillar cock (fancy) 15 mm foam flow each 138.00
7411 125 mm grating with waste hole each 30.00
7412 Rectangular type with openable circular lid 150 mm size 18 mm high
with 100 mm dia (110 gm) each 118.00
7426 Cat's eye each 100.00
7427 Water stops Serrated with central bulb (225 mm wide, 8-11 mm thick) metre 200.00
7428 Water stops Dumb bell with central bulb metre 160.00
7429 Kickers metre 185.00

No.
7430 Wedge expansion hold fastener 1/4" or 6 mm each 11.00

7439 8mm thick (mirror polished tiles machine cut edge) Raj Nagar white sqm 500.00
7442 Wheel 75 mm dia. 40 mm wide each 62.00
7443 Aluminium single cleat of size 30x32x3 mm each 14.00
7444 Aluminium grip strip of size 50x12x2 mm each 11.00
7445 25 mm thick prelaminated flush door shutter both side decorative sqm 800.00
7449 Aluminium U beading kg 210.00
7451 Glass sheet (Pin headed) 4 mm thick sqm 305.00
7452 Raj nagar plain white marble (table rubbed and polished) 18 mm thick
(slab area upto 0.50 sqm) sqm 575.00
7453 Raj nagar plain white marble (table rubbed and polished) 18 mm thick
(slab area more than 0.50 sqm) sqm 690.00
7466 Second class deodar teak wood lipping 30 mm wide x 12 mm thick metre 24.00
7468 Veneered particle board with commercial veneering on both sides 12 mm
thick sqm 500.00
7477 Prelaminated particle board with one side decorative and other side
balancing lamination, flat pressed 3 layer & graded (medium density)
Grade i, Type II conforming to IS : 12823 (exterior grade) 12 mm thick sqm 540.00
Grade I, Type II conforming to IS : 12823 (exterior grade) 18 mm thick sqm 650.00
Grade I, Type II conforming to IS : 12823 (exterior grade) 25 mm thick sqm 900.00
7485 Oxidised M. S. hinges finished with nickel plating 50 mm (Over all width) metre 40.00
7486 Oxidised M. S. hinges finished with nickel plating 65 mm (Over all width) metre 52.00
7495 PTMT Ball Cock 15mm complete with Epoxy Coated Aluminium Rod &
H.D. Ball each 100.00
7500 PTMT Angle Stop cock with Flange 15 mm each 100.00
7501 PTMT Swiveling shower 15 mm each 70.00
7503 PTMT Liquid Soap Container of 400 ml capacity each 105.00
7504 PTMT - Towel Ring 215x200x37 mm each 130.00
7505 PTMT - Towel Rail (450 mm long ) each 135.00
7506 PTMT - Towel Rail (600 mm long) each 165.00

No.
7507 PTMT Shelf 450x124x36 mm each 200.00

7508 PTMT - Urinal Spreader 15 mm each 76.00
7509 PTMT Soap Dish/Holder 138x102x75 mm each 84.00
7512 PTMT handle 125x34x24 mm each 24.00
7514 PTMT butt hinges 75x60x10 mm each 33.00
7516 PTMT Tower bolt 152x42x18 mm each 48.00
7518 PTMT door catcher 72x42 mm each 24.00
7552 Coir veneered board 4 mm thick sqm 290.00
7621 Hubless centrifugally cast (spun) iron pipes as per IS 15905 - 100 mm dia
(3000 mm length pipe) metre 700.00
7622 Hubless centrifugally cast (spun) iron pipes as per IS 15905 - 75 mm dia
(3000 mm length pipe) metre 570.00
100mm dia each 230.00
7625 Hubless centrifugally cast (spun) iron double equal plain junction as per
IS 15905 - 100x100x100x100 mm dia each 510.00
7626 Hubless centrifugally cast (spun) iron double equal plain junction as per
IS 15905 - 75x75x75x75 mm dia each 275.00
7627 Hubless centrifugally cast (spun) iron single equal plain junction as per
IS 15905 - 100x100x100 mm dia each 400.00
7628 Hubless centrifugally cast (spun) iron single equal plain junction as per
IS 15905 - 75x75x75 mm dia each 215.00
7629 Hubless centrifugally cast (spun) iron double unequal plain junction as
per IS 15905 - 100x100x75x75 mm dia each 400.00
7630 Hubless centrifugally cast (spun) iron single unequal plain junction as
per IS 15905 -100x100x75 mm dia each 375.00
7631 Hubless centrifugally cast (spun) iron double equal plain invert
branch as per IS 15905 - 100x100x100x100 mm dia each 625.00
7632 Hubless centrifugally cast (spun) iron single equal plain invert branch as
per IS 15905 - 100x100x100 mm dia each 390.00
7633 Hubless centrifugally cast (spun) iron single equal plain invert branch as
per IS 15905 - 75x75x75 mm dia each 260.00
7634 Hubless centrifugally cast (spun) iron single unequal plain invert branch
45 degree as per IS 15905 - 100x100x75 mm dia each 430.00
7635 Hubless centrifugally cast (spun) iron 65 mm offset with 100 mm dia
pipe as per IS 15905 each 360.00
7636 Hubless centrifugally cast (spun) iron 65 mm offset with 75 mm dia pipe
as per IS 15905 each 295.00
7639 Hubless centrifugally cast (spun) iron bend with access door - 100mm
dia as per IS 15905 each 365.00

No.
7640 Hubless centrifugally cast (spun) iron bend with access door - 75mm dia
as per IS 15905 each 290.00
7641 Hubless centrifugally cast (spun) iron terminal guard (slotted cowl) -
100 mm dia as per IS 15905 each 270.00
7642 Hubless centrifugally cast (spun) iron trap with 100 mm inlet and 100 mm
outlet as per IS 15905 each 540.00
7643 Hubless centrifugally cast (spun) iron trap with 100 mm inlet and 75 mm
outlet as per IS 15905 each 385.00
7644 SS 304 grade shielded coupling with EPDM rubber gasket for 100mm dia
Hubless centrifugally cast (spun) iron each 275.00
7645 SS 304 grade shielded coupling with EPDM rubber gasket for 75 mm dia
Hubless centrifugally cast (spun) iron each 250.00
7651 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 100 mm dia metre 765.00
7660 Ductile Iron class K -9 pipe Conforming to I.S. 8329 - 600 mm dia metre 7560.00
7682 Ductile Iron K - 12 specials suitable for push on jointing up to 600 mm dia quintal 12400.00
7683 Ductile Iron K - 12 specials suitable for push on jointing over 600 mm dia quintal 17200.00
7684 Ductile Iron specials suitable for mechanical jointing as per I.S. 9523 -
up to 600 mm dia quintal 13050.00
7685 Ductile Iron Specials suitable for mechanical jointing as per I.S. 9523
over 600 mm dia quintal 18750.00

No.
for lead jointing up to 300 mm dia quintal 5190.00
for lead jointing over 300 mm dia quintal 6200.00
7710 S&S Centrifugally (Spun) C.I. Pipe specials suitable for mechanical
joint as per I.S. 13382 up to 300 mm dia quintal 8571.00
7711 S&S Centrifugally (Spun) C.I. Pipe Specials suitable for mechanical
joint as per I.S. 13382 over 300 mm dia quintal 9048.00
7712 Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 100 mm dia metre 1310.00
7720 Screwed double flanged centrifugally cast (spun) C./. Pipe of Class B

No.
7736 Extruded burnt flyash clay sewer bricks conforming to I.S 4885 1000 Nos 5400.00
7737 Fly ash bricks conforming to I.S. 12894 1000 Nos 4300.00
7738 Calcium Silicate Bricks machine moulded conforming to I.S. 4139 1000 Nos 5400.00
7742 Bitumen emulsion medium setting (M.S.) conforming to IS : 8887 tonne 27909.00
7747 M.S. cap 150 mm dia each 150.00
7748 M.S. cap 200 mm dia each 200.00
7755 Gravel 1.5 mm to 2 mm cum 850.00
7758 uPVC blind pipe 100 mm dia as per IS: 12818 metre 442.00
7759 uPVC slotted pipe 100 mm dia as per IS: 12818 metre 480.00
7760 M.S. cap 100 mm dia each 135.00
7761 M.S. bail plug 100 mm dia each 160.00
7762 Precast R.C.C. perforated slab each 875.00
7763 Water supply tanker of 5000 litre capacity each 900.00
7767 Stone cleaning chemical approved by ASI litre 295.00
7768 Water repallent chemical approved by ASI litre 1200.00
7769 Stone surface strengthening chemical approved by ASI litre 900.00
7770 Turpentine oil litre 55.00
7771 Liquid Ammonia 5% litre 160.00
7772 Pea Gravel cum 950.00
7773 Coloured inter locking C.C. paver Block (60 mm thick, M-35) sqm 450.00

No.
7774 Stone size 10x10x7.50cm each 10.00

7775 Sodium pentachlorophenate kg 550.00
7776 Concrete paver block of grade M-30 made of C&D waste (60mm thickness) sqm 317.22
7800 Ceramic Glazed Tiles 1st quality minimum thickness 5mm in all
colours shades and designs except burgundy, bottle green, black sqm 212.00
7801 Ceramic Glazed Tiles 1st quality 300 x 300 mm in all shades and
designs of White, Ivory, grey, Fume Red brown etc. sqm 209.10
7802 Ceramic Glazed Tiles 1st quality 300 x 300 in all shades designs
except White, Ivory, Grey, Fume Red Brown etc. sqm 260.00
7803 Rectified Ceramic Glazed Tiles 1st quality 300 x 300 mm or more in
all shades designs White, Ivory, Grey, Fume Red Brown etc. sqm 340.00
7804 Rectified Ceramic Glazed Tiles 1st quality 300 x 300 mm or more in
all shades designs except White, Ivory, Grey, Fume Red Brown etc. sqm 400.00
7805 Salem Stainless steel AISI - 304 (18/8) Orrisa pattern W.C. pan
724mm X 578 mm each 4500.00
7806 Salem Stainless steel AISI - 304 (18/8) Round basin 405mm X 355 mm each 1500.00
7807 Salem Stainless steel AISI - 304 (18/8) Wash basin 530mm X 345 mm each 2000.00
7850 Agaria White marble slab plain 18 mm thick sqm 1100.00
7857 P.T.M.T. Grating square slit 150 mm each 66.75
7858 P.T.M.T. Urinal cock 15 mm dia each 106.50
7859 P.T.M.T. Bib cock with nozzle 15 mm each 154.50
7861 P.T.M.T. Stop cock (concealed) 15 mm each 133.50
7893 Tactile tile sqm 1000.00
7895 Matt finished vitrified tile 100x100 x16 mm sqm 1000.00
7896 Vitrified tile sqm 500.00
7900 Modular common burnt clay bricks of class designation 7.5 1000 Nos 4000.00
7901 Machine moulded perforated common burnt clay FPS (non modular)
bricks of class designation 12.5 1000 Nos 4700.00
7902 Machine moulded common burnt clay modular perforated bricks of
class designation 12.5 1000 Nos 5200.00
7903 Machine moulded common burnt clay FPS (non modular) bricks of
class designation 12.5 1000 Nos 5000.00
7904 Machine moulded common burnt clay tile bricks of class designation 12.5 1000 Nos 4900.00
7911 Chemical Rust Remover litre 210.00
7913 Epoxy kg 585.00
7914 SBR Polymer kg 190.00
7915 Woven PVC cloth sqm 25.00
7917 Hire charges of compressure day 645.00

No.
7921 Adhesive chemical ml 2.00
7922 Bit of drilling machine for Hole upto 30mm dia each 500.00
7923 GI injection nipple 12mm dia, 75mm long each 42.00
7924 Blowing compressed air for cleaning holes upto 30mm dia each 10.00
7925 L shaped 100mm long, 10mm dia mild steel shear key kg 67.00
7927 Acrylic Polymer chemical for cracks kg 31.00
7928 Hire charges of Plant and machinery, it can inject - 350kg/day day 100.00
7929 Shear loops (6mm dia GI wire rope) (For vertical joints) 6 nos on each side each 192.00
7930 dowel tubes (Corrugated GI pipes 50 to 80mm dia) (For horizontal joints) metre 120.00
7931 Hooks for lifting (Alloy steel) having 2.5 tonne capacity each 250.00
7996 Factory made EPS light weight composite sandwitched wall/roof
panel (50mm thick) having core material of EPS granule balls/beads
(conforming to IS 4671:1984 and shall have density not less than
15kg per cum). The outer face on both sides of the panels will be non
asbestos fiber cement board confirming to IS 14862:2000 or Calcium
silicate board confirming to EN 14306:2009 of 5mm thick each. sqm 735.25
silicate board confirming to EN 14306:2009 of 5mm thick each sqm 845.00
8001 24 mm thick Factory made shutters with style, rails and panels of
PVC extruded sections in white, grey or wooden finish sqm 1085.93
8003 Factory made PVC rigid foam panelled shutter i/c carriage sqm 1547.45
8004 Factory made PVC rigid foam panelled shutter as per IS : 4020 i/c carriage sqm 1547.45
8006 Factory made PVC rigid foam sheet 1 mm thick sqm 155.80
8008 Factory made prelaminated PVC rigid foam sheet 5 mm thick sqm 752.00

No.
8010 48mmX40mmX1.5mm thick Factory made door frame of PVC

extruded sections in white, grey or wooden finish metre 125.79
8011 Factory made door frame PVC extruded sheet i/c carriage metre 251.58
8012 Adhesive solvent cement kg 140.00
8013 Factory made EPS Core wallpanel /roof panel sandwiched between
two Engineered welded wire fabric mesh of 3 mm dia G.I. wire
mesh,with 50 mm pitch in both the directions, kept at 120-135 mm
gap and interconnected by the zig zag G.I. wire of 3 mm dia at alternate
row by welding. sqm 1650.00
8014 Factory made door frame of size 50x47 mm with wall thickness 5 mm
made of single piece extruded profile metre 298.74
8015 Expanded poly ethylene Foam sheet 4mm thick of Density 40kg/m3 sqm 18.00
8017 Fire rated door frame made with 1.6 mm thick G.I sheet (120 minutes
fire rating) metre 1000.00
8018 Fire rated door shutter made with 1.6 mm thick G.I sheet (120 minutes
fire rating) including hinges ( without glass panels) sqm 5000.00
8019 GI sheet 0.8 mm thick confirming to IS 277:1992 kg 75.00
8020 Factory made EPS Core wall panel /roof panel sandwiched between
two Engineered welded wire fabric mesh of 3 mm dia G.I. wire mesh,
with 50 mm pitch in both the directions, connected by G.I. wire of
3mm dia at alternate row by welding sqm 600.00
8021 Bamboo wood Tile Flooring 14mm thick of minimum size 1800mm x
130mm sqm 3470.00
8022 Bamboo wood Quarter Round 18mm thick of size 1900mm x 18mm metre 112.00
8023 Bamboo wood door reducer 14mm thick of size 1900mm x 44mm metre 255.00
8024 Bamboo wood Skirting 14mm thick of Size 1900mm x 85mm metre 300.00
8025 Bamboo wood Tile Wall Cladding 10mm thick of size 1900mm x 135mm sqm 3385.00
8026 Bamboo wood T-mold 14mm thick of size 1900mm x 44mm metre 250.00
8027 Bamboo wood Threshold 14mm thick of size 1900mm x 44mm metre 255.00
8028 Bamboo wood shutter of doors 10 cudm 1700.00
8029 Bamboo wood panelling (10mm thick) 10 cudm 1680.00
8030 Superior class Bamboo wood door frame 65 mm thick, 10 cudm 1675.00
8031 Aluminium sheets Grade 5052, 4 mm thick for wall panel/deck panel/
WRB panel/Kicker Panels/door closing panels ( for form work) sqm 8500.00
8032 Aluminium sheets Grade 5052, 4 mm thick for Internal Corner/Column
Corners/ ( for form work) sqm 11500.00
8033 Aluminium sheets Grade 5052, 4 mm thick for Mid Soldier/End soldier
(for form work) sqm 32000.00
Accessories for aluminium form work
8036 soldier tie 370mm each 290.00
8037 Adjustable prop-2.0 x2.0 m each 1080.00
8038 Pin-50 each 15.00
8039 Pin-127 each 55.00
8040 wedge each 14.00
8041 wall tie-150 (355 mm ) each 45.00
8042 Polythene Sleeve 90 x 150mm each 3.00
8043 Polythene Roll - 150mm Long. each 6.00
8044 Vertical Soldier -1100mm each 365.00

No.
8045 Wall Attached Bracket 600x1000mm each 985.00

8046 Allignment Pipe - 3.00 Mtr. each 995.00
8047 Allignment Bracket each 475.00
8048 Tie Rod for Bracket - 500mm each 115.00
8049 Anchor Wing Nut Ø100 mm each 64.00
8050 Debit Pin - 250mm each 60.00
8051 PVC Pipe Ø20mm - 150mm long each 5.00
8052 PVC Cone each 5.00
8053 Bolt+Nut - 16 x 80 mm each 30.00
8054 Flat Washer Ø16, 3mm thik each 5.00
8055 Bolt+Nut - 16 x 30 mm each 18.00
8100 Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm 10 Nos 123.00
8101 SS ball bearing of size 100 x89x3mm each 450.00
8116 Zinc alloy (white powder coated) 3D Hinges for uPVC door each 451.00
8117 Zinc alloy (white powder coated) handles with zinc plated mild steel
multi point locking having transmission gear, cylinder with keeps
and one side key for uPVC casement door each set 2296.00
8118 Zinc alloy (white powder coated) handles along with zinc plated mild
steel multi point locking having transmission gear with keeps for
uPVC sliding window each set 1394.00
8119 Zinc alloy (white powder coated) handles with key along with zinc
plated mild steel multi point locking having transmission gear with
keeps for uPVC sliding door each set 1150.00
8121 uPVC extruded (small series) casement window frame size 47x50mm metre 258.30
8122 uPVC extruded (small series) casement window sash/window mullion
size 47x68 mm metre 282.90
8125 uPVC extruded glazing bead of appropriate dimension for small series
casement window Sash metre 98.40
8126 uPVC extruded (big series) casement window frame size 67x60 mm metre 319.80
8127 uPVC extruded (big series) casement door frame size 67x64 mm metre 360.80
8128 uPVC extruded (big series) casement window sash/window mullion/
door mullion size 67x80 mm metre 426.40
8129 uPVC extruded (big series) casement door sash size 67x110 mm metre 516.60
8130 uPVC extruded glazing bead of appropriate dimension for big series
casement window/door sash metre 123.00
8131 uPVC extruded glazing bead of appropriate dimension for small series
sliding window sash metre 60.00
8132 uPVC extruded glazing bead of appropriate dimension for big series
of sliding window/ door sash metre 85.00
8133 uPVC extruded (small series) 2 track sliding window frame size 52x
44 mm metre 285.00
8134 uPVC extruded (big series) 2 track sliding window/door frame size
67x50mm metre 385.00
8135 uPVC extruded (small series) 3 track sliding window frame size
92x44 mm metre 380.00
8136 uPVC extruded (big series) 3 track sliding window/door frame size
116x45mm metre 530.00
8137 uPVC extruded (small series) 2 track sliding window sash/3 track sliding
window sash size 32x60mm metre 265.00

No.
8138 uPVC extruded (big series) 2 track sliding window sash size 46x62mm metre 325.00
8139 uPVC extruded (big series) 3 track sliding window sash size 46x62mm metre 325.00
8140 uPVC extruded interlock of appropriate dimension for small series sliding
window sash metre 80.00
8141 uPVC extruded interlock of appropriate dimension for big series sliding
window/ door sash metre 90.00
8142 uPVC extruded inline adaptor of appropriate dimension for big series
sliding window/door sash metre 90.00
8143 uPVC extruded 2 track sliding door sash/ 3 track sliding door sash
(big series) size 46x82mm metre 350.00
8144 Bamboo Mat corrugated sheets 3.5 to 4mm thick conforming to
IS 15476:2004 sqm 2648.00
8145 Bamboo Mat Ridge cap 3.5 to 4mm thick conforming to IS 15476:2004 metre 2570.00
8200 A.P.P. modified polymeric felt (two layers) 1.5 mm thick sqm 80.00
8201 A.P.P. modified polymeric felt (two layers) 2 mm thick sqm 100.00
8203 A.P.P. modified 2 mm thick membrane reinforced with glass fibre matt sqm 126.67
8204 A.P.P. modified 3 mm thick membrane reinforced with glass fibre matt sqm 190.00
8205 A.P.P. modified 3 mm thick membrane reinforced with polyester matt sqm 205.00
8219 Stainless steel butt hinges (heavy weight) 125x64x2.5 mm IS :12817 marked 10 Nos 350.00
8222 M.S. heavy weight butt hinges 125x90x4.0 mm IS: 1341 marked. 10 Nos 210.00
8223 M.S. heavy weight butt hinges 100x75x3.5 mm IS: 1341 marked 10 Nos 160.00
8225 M.S. heavy weight butt hinges 50x40x2.5 mm IS : 1341 marked 10 Nos 80.00
8226 Concealed zinc coated hinges 19-20 mm thick with mounting plate 10 Nos 420.00

No.

8500 Water for jetting / blowback 1000 litre 1500.00
8501 Polymer modified cementation coating kg 140.00
8502 Fibre glass cloth sqm 25.00
8504 Multi surface paint litre 255.00
8509 Special Primer (C.W.) litre 140.00
8510 Metal Primer (U.G.) litre 90.00
8511 Fibre reinforced elastomeric liquid water proofing membrane litre 198.69
8512 Cementitious water proofing coating with elastic polymers kg 189.13
8513 Acrylic modified resin based texture kg 36.00
8514 40 mm long S.S screws with plastic rawl plugs 100 40.00
8515 Galavanised MS 8 mm outer diameter M-6 dash fastener 50mm long each 31.00
8516 ZMB 60/equivalent kg 105.00
8517 ZMB thinner litre 205.00
8518 Zycoprime / equivalent litre 210.00
8519 Zycosil / equivalent litre 1800.00
8520 Elastobar / equivalent kg 300.00
8552 Mineral fibre beveled tegular edged ceiling tiles 595 x595mm,16 mm thick sqm 830.00
8553 Mineral fibre beveled tegular edged ceiling tiles 595 x595mm,16 mm
thick with bio-block conforming to ISO 5 (class 100) specifications. sqm 920.00
8554 Mineral fiber beveled tegular edged ceiling tiles 595 x595mm,20 mm thick. sqm 1040.00
8555 G.I main runner 15 x32 mm of 3000 mm length, 0.33 mm thick each 185.00
8558 G.I hanger rod 6mm dia fully threaded upto 1000 mm length each 26.00
8559 Stainless steel U Channel of size (50x25x2mm) metre 160.00
8560 Non staining water resistant clear silicon metre 65.00
8561 Extruded polystyrene rigid insulation board 50 mm thick sqm 525.00
8562 Expanded Polystyrene insulation board 120 mm thick confirming to
IS 4671-1984, Fire retardant property self-extinguishing type as per
EN 13501-1 sqm 800.00
8563 15 mm thick, light weight, integral densified micro look edged,false
ceiling tiles of size 595x595 mm. sqm 720.00
8564 15 mm thick, light weight,fully perforated square/butt edge integral
densified,false ceiling tiles of size 595x595 mm. sqm 900.00
8565 Galavanised MS hanger rod 6 mm dia MS fully threaded up to 1000mm
length each 26.00
8566 Powder coated steel section main-T ceiling sections 15x42x0.40 mm
(3000 mm long) each 235.00
8567 Galvanized mild steel perimeter wall angle 22x19x0.40 mm (3000mm
long) each 115.00

No.
8568 Powder coated Galvanised Iron intermediate cross-T section 15x42x

0.40 mm (1200 mm long) each 95.00
8569 Powder coated Galvanized Iron intermediate cross-T section 15x42x
0.40mm (600 mm long ) each 47.00
8570 GI Main T ceiling section 30x25x0.3 mm (3 metre long) each 187.00
8571 GI Perimeter wall angle 25x25x0.4 mm (3 metre long) each 157.00
8576 Powder coated Galvanized Iron intermediate cross-T section wire
diameter 3.00 mm). sqm 190.00
8577 Crates made of Mesh type 10x12 (D=100 mm) Zn+PVC coated. Mesh wire
diameter 2.70/3.70 mm (ID/OD). sqm 220.00
8578 Crates made of Mesh type 10x12 (D=100 mm) Zn+10% Al alloy +PVC
coated. Mesh wire diameter 2.70/3.70 mm (ID/OD). sqm 290.00
8579 Cold form light gauge Steel C-section of thickness 0.75mm i/c zink
coating/sliting etc. kg 130.00
8580 Wastage of cold form light gauge steel kg 17.00
8581 12 mm thick micro tegular edged semi perforated GRG (Glass Fibre
Reinforced Gypsum) false celing tiles of Size 595x595 mm sqm 510.00
8582 12 mm thick micro tegular edged fully perforated GRG (Glass Fibre
Reinforced Gypsum) false celing tiles of Size 595x595 mm sqm 600.00
8583 10 mm thick square edge fully perforated GRG(Glass Fibre Reinforced
Gypsum) false celing tiles of Size 595x595 mm sqm 750.00
8587 Galvanized iron intermediate cross-T section 15x32x0.33 mm (600mm long) each 35.00
8588 Galavanised MS hanger rod 6mm dia MS fully threaded up to 1000mm length each 26.00
8589 Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm thick
on edges sqm 685.00
8590 Galvanised Steel main Tee ceiling section Size 24x38x0.33 mm (3 metre
long) each 120.00
8591 Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm (3.00 metre
long) each 65.00
8592 Galvanised Steel intermediate cross T section Size 24 x 25 x 0.33mm
8596 Galvanised MS 8mm outer diameter M-6 dash fastener 25mm long each 32.00
8599 GI Metal Tile Lay-in Plain Tegular edge global white color tiles of Size
595x595 mm and 0.5 mm thick sqm 612.00
8600 GI Metal Tile Lay-in Perforated Tegular edge global white color tiles
of Size 595x595 mm and 0.5 mm thick sqm 715.00
8601 PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm
and 12.5 mm thick sqm 880.00
8602 Gypsum Tiles Fully Perforated Square edge of Size 595x595 mm

No.
8619 Galavanised MS L-shape level adjuster of size 85x25x2 mm each 15.00
8620 Vitrified floor tile 50x50 cm conforming to IS 15622:2006 group (B1a) sqm 490.00
8624 "Border tiles 200x75mm size each 16.00
8626 Poly propylene- Random - Co - Polymer (PPR) pipes PN-16 (SDR 7.4) -
20 mm Outer dia metre 43.27
8630 Poly propylene- Random - Co - Polymer (PPR) pipes PN-10 (SDR 11) -
8642 Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia metre 793.30
8646 Weather Silicon sealant cartridge 100.00

No.

8648 Hermetically sealed double glazed unit made with 6 mm thick clear float
glass both side having 12 mm air gap sqm 2150.00
8649 Stainless steel (SS 304 grade) adjustable friction window stay 205 x 19 mm each 172.00
8655 Autoclaved aerated cement (AAC) blocks cum 2600.00
8656 Gypsum panel 666 X 500 X 100 mm size sqm 480.00
8657 Bonding plaster for Gypsum panel kg 25.00
8658 Precast C&D waste concrete block 1000 Nos 25150.00
8660 Aluminium casement window fastener (Anodised AC 15) each 44.00
8661 Aluminium casement window fastener (powder coated ) each 47.00
8662 Aluminium casement window fastener (polyester powder coated) each 46.00
8663 Aluminium round shape handle (anodised AC 15) outer dia 100 mm each 53.00
8664 Aluminium round shape handle (powder coated) outer dia 100 mm each 56.00
8665 Aluminium round shape handle (polyester powder coated) outer dia
100 mm each 60.00
8667 UV stabilised 2 mm thick plain FRP sheet sqm 430.00
8668 UV stabilised 2 mm thick corrugated FRP sheet sqm 485.00
8669 Mangalore ridge tiles 20 mm thick each 8.00
8670 Mangalore tiles 20 mm thick each 8.00
8671 Precoated galvanised iron profile sheet 0.50 mm TCT sqm 350.00
8672 Precoated galvanised steel plain ridges 0.50 mm TCT and 500-600mm
wide metre 210.00
8673 Precoated galvanised steel flashings/aprons 0.50 mm TCT and upto
600mm wide metre 210.00
8675 Precoated galvanised steel north light curves metre 230.00
8677 Precoated galvanised steel crimp curve sqm 230.00
8682 Epoxy Grout kg 371.00
8683 Red sand stone gang saw cut 30 mm thick sqm 425.00
8685 Delineator each 300.00
8686 Precast C.C. Kerb stone M - 25 cum 5500.00
8687 Thermoplastic paint kg 65.00
8688 Glass beads kg 70.00
8690 High intensity retro - reflective sheet as per IRC 67-2001 sqm 1300.00
8691 Punched tape concertina coil 600 mm dia 10 m openable length (Total
length 90 m) bundle 600.00
8692 RBT reinforced barbed wire metre 6.50
8693 Turn buckle and strengthening bolt each set 40.00

No.
8694 Precast pavement slab 450 x 450 x 50 mm (M - 30) each 135.00

8695 Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia
4 mm sqm 280.00
4 mm, PVC coated to outer dia 5 mm sqm 300.00
3 mm sqm 360.00
8698 Stainless steel cramps(weight 260 grams) with nuts, bolts and washer
for dry stone cladding each 100.00
8699 8 mm thick tapered edge calcium silicate board sqm 265.00
8700 10 mm thick calcium silicate board sqm 420.00
8701 SS pipe 304 grades with press fit technology as per JIS 3448 standard
8703 Telescopic drawer channels 300 mm long set 230.00
8704 Stainless steel roller for sliding arrangement in racks/ cupboards/cabinets
shutter each 9.00
8705 50 mmX42 mmX2 mm thick Factory made door frame of PVC extruded
sections in white, grey or wooden finish metre 160.00
8706 25 mm thick factory made PVC flush door shutter i/c carriage sqm 1700.00
8707 Factory made glass reinforced plastic door frame 90x45 mm i/c carriage metre 467.00
8708 30 mm thick factory made glass fiber reinforced plastic panel door
shutter i/c carriage sqm 2326.00
8709 30 mm thick factory made solid PVC profile panelled door single piece
extruded profile decorative finish (wood grain printed on both side) sqm 2100.00
8710 Factory made solid PVC door frame 60 x 30 mm i/c carriage metre 315.00
8711 20 mm factory made solid PVC panel door shutter i/c carriage sqm 2050.00
8712 30 mm thick factory made solid PVC profile panelled door single piece
extruded profile non decorative finish sqm 2000.00
8713 Fiber glass reinforced plastic chajja sqm 3000.00
8714 Magnetic catcher triple strip vertical type each 24.00
8715 Magnetic catcher double strip horizontal type each 18.00
8716 100 mm mortice lock with 6 levers for aluminium door each 375.00
8719 2nd class teak wood moulded beading or Taj beading/ornamental
bleading of size 18X5 mm metre 28.00
8720 Ceiling sections 0.55 mm thick having a knurled web of 51.55 mm and two
flanges of 26 mm each with lips of 10.55 mm metre 35.00
8721 Perimeter channel having one flange of 20 mm and another flange of
30 mm with thickness of 0.55 mm and web of length 27 mm metre 22.00
8722 Nylon sleeves & wooden screws (40 mm) each 2.00
8723 Counter sunk ribbed head screw 25 mm 100 Nos 68.00
8724 12 mm thick marine plywood conforming to IS: 710 sqm 695.00
8725 12 mm thick fire retardant plywood conforming to IS: 5509 sqm 850.00
8726 1.5 mm thick decorative laminated sheet sqm 365.00
8730 30 mm thick factory made glass fiber reinforced plastic flush door shutter
i/c carriage sqm 2675.00
8731 High polymer modified quickset tile adhesive kg 9.00
8732 Synthetic ployster triangular fibre of length 12 mm, effective diameter 10-40
microns and specific gravity of 1.34 to 1.40 kg 365.00

No.
8733 Synthetic ployster triangular fibre of length 6 mm, effective diameter
10-40 microns and specific gravity of 1.34 to 1.40 kg 400.00
8734 P.V.C. Single piece extruded door frame of profile size 50 mm x 47mm
with wall thickness of 5 mm metre 255.00
8735 35 mm thick factory made solid panel PVC door shutter of single
piece extruded profile non decorative finished (Matt finished) sqm 2150.00
piece extruded profile decorative finished (wood grain finished) sqm 2600.00
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50mm
dia wire sqm 400.00
8738 Factory made door frame fire rated (60 minutes) made with 16 SWG
G.I. Sheet of section 143 mm x 57 mm duly filled with vermuculite
based concrete mix metre 1050.00
8739 Fire rated door shuttere made with 16 SWG G.I. sheet (60 minutes)
without panel sqm 4500.00
8740 Fire seal Putty kg 295.00
8741 Clear fire resistant glass panes 6mm thick (60 minutes) sqm 21500.00
8742 G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/ m²) with
ceramic tape of suitable thickness and fire resistant primer coating metre 295.00
8743 Matrix Mineral Board metre 68.00
8744 Panic Bar / latch (Double point) each 5200.00
8745 65 mm x 55 mm x 2 mm thick Factory made door frame of PVC
extruded section in white, grey or wooden finish metre 355.00
8746 37 mm thick Factory made shutter with style,rails and panels of PVC
extruded section in white or grey finish i/c carriage sqm 2400.00
8747 75 mm x 53 mm x 2.0 mm thick Factory made door frame of PVC
8748 37 mm thick Factory made fusion welded shutter with style, rails and
panels of PVC extruded section in wooden finish sqm 2600.00
8749 Zinc alloy (white powder coated) touch lock with hook for wire mesh shutter each 120.00
8750 Zinc alloy (white powder coated) casement handle for uPVC window/door each 130.00
8751 Zinc alloy (white powder coated) touch lock withhook for uPVC window/door each 105.00
8752 Zinc alloy body with single nylon roller (weight bearing capacity to be
40 Kg) for uPVC sliding window each 56.00
8753 Stainless Steel (SS - 304) with adjustable double nylon roller (weight
bearing capacity to be 120 Kg) for uPVC sliding door/window each 95.00
8754 Zinc alloy (white powder coated) cresent lock for uPVC sliding door/window each 115.00
8755 Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for uPVC windows each 205.00
8756 Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for uPVC windows each 230.00
8757 Stainless steel friction hinges (SS-304 grade) size 300 x 19 x 1.9 mm for
uPVC window each 245.00
8760 Glass panes of required thickness having 60 minutes of fire resistance
both integrity and radiation control (EW 60) and minimum 20 minutes of
insulation (EI 20) sqm 22500.00
8761 Scaffolding net made of high density polyethylene UV stabilized having
density 100gm/ sqm. sqm 21.50
8772 Aluminium Track on bottom rail for uPVC window metre 30.00
8773 Wool pile/ weather pile strip for uPVC sliding window metre 20.00
8775 Steel Galvanised tubular reinforcement for uPVC door/ window metre 60.00

No.
8777 GI Fastener 100x8 mm each 15.00

8784 8 mm thick Calcium silicate perforated tiles of size 595 x595 mm sqm 833.00
8805 Reducer for48.60 mm X 42.70 mm outer Dia SS pipe each 410.00

No.
8830 Reducing Tee for 22.22 mm X 15.88 mm outer dia SS each 179.00
8843 Reducing Tee for 48.60mm X 34.00 mm outer dia SS pipe each 887.00
8844 Reducing Tee for 48.60mm X 42.70mm outer dia SS pipe each 887.00
8845 Stainless steel Male thread Tee for 15.88 mm outer dia X 15 mm nominal
dia threaded each 179.00
8846 Stainless steel Male thread Tee for 22.22 mm outer dia X 15 mm nomina
8848 Stainless steel Male thread Tee for 28.58 mm outer dia X 15 mm nomina

No.

No.
8907 Stainless steel Male threaded Connector/Adapter for 42.70 mm outer
dia X 40 mm nominal threaded each 726.00

No.

8917 SS Female Threaded Elbow 90o for 15.88 mm outer dia X 15 mm
8918 Stainless steel Female Threaded Elbow 90o for 22.22 mm outer dia
X 15 mm nominal dia threaded each 191.00
X40 mm nominal dia threaded each 478.00
8926 Stainless steel Male Threaded Elbow 90o for 15.88 mm outer dia X
15 mm nominal dia threaded each 191.00
8927 Stainless steel Male Threaded Elbow 90o for 22.22 mm outer dia X
8928 Stainless steel Male Threaded Elbow 900 for 22.22 mm outer dia X
8930 Stainless steel MaleThreaded Elbow 900 for 34.00 mm outer dia X

No.
8945 4 Point facade glass bracket without flat head bolts Nos 3318.00
8946 2 Point facade glass bracket (wall mounted with out flat head bolt) Nos 1659.00
8947 1 Point facade glass bracket (wall mounted with out flat head bolt) Nos 1300.00
8948 Flate head bolt for brackets of spider glazing Nos 651.00
8949 400 mm long fin plate without fastners pair 5931.00
8953 Micro Silica kg 32.00
8954 Stop end tubes for diaphragmwall 600 mm dia. sqm 4.50
8955 Driving end tubes for diaphragm wall 600 mm dia. sqm 72.00
8956 Bi-Axial Extruded GeoGrids of Minimum Tensile Strength 15 kN/m in
the longitudinal and transverse direction sqm 100.00
8957 Bi-Axial Extruded GeoGrids of Minimum Tensile Strength 20kN/m in
8960 Geosynthetic Drainage with two filtering nonwoven geotextiles having
a “W” configuration as longitudinal parallel channels. Minimum
thickness to be 7.2mm, with two filtering UV stabilized polypropylene
nonwoven geotextile of minimum thickness of 0.75mm having pores
of 150 micron and tensile strength of 8.0 kN/m and having plane flow
capacity of 2.1 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure,
tensile strength of 18 kN/m , with mass per unit area of 740 gsm. sqm 530.00
8961 Geosynthetic Drainage Composite having thermobonding a draining
core - HDPE geonet comprises of two sets of parallel overlayed ribs
integrally connected to have a rhomboidal shape with a polyethylene
film and a nonwoven geotextile having mass per unit area 130 g/m2
and tensile strength of 8.0 kN/m having in plane flow capacity of 0.7
L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile
strength of 13.5 kN/m , with mass per unit area of 830 gsm, sqm 630.00
8962 Synthetic Geogrid having Ultimate tensile strength- 100 kN/m sqm 220.00

No.

40800, conforming to IS 1254, IS 737, IS 2676, 0.71 mm thick, the
profile detail width 1044/920 mm, cover width 1000/875 mm. sqm 600.00
40800, conforming to IS 1254, IS 737, IS 2676, 0.91 mm thick, the
profile detail width 1044/920 mm, cover width 1000/875 mm. sqm 785.00
9001 C.P. Brass Centre Hole Basin Mixer With Cast Spout each 1600.00

BASIC RATES
0.4 CARRIAGE CODES
(Carriage for 5.0 km lead by Mechanical Transport including loading, Unloading and stacking).

No.
2200 Steam coal tonne 120.00
2201 Bricks 1000 Nos 276.72
2202 Stone aggregate below 40 mm nominal size cum 103.77
2203 Coarse sand cum 103.77
2204 Timber cum 118.59
2205 Steel tonne 92.24
2206 Stone aggregate 40 mm nominal size and above cum 112.79
2207 Brick tiles 1000 Nos 166.03
2208 Lime cum 103.77
2209 Cement tonne 92.24
2211 Tar bitumen tonne 103.77
2215 Soling stone & masonry stone cum 122.08
2216 Stone blocks white & red sand stone & kota stone slab tonne 92.24
2224 S.W. pipes100 mm dia 100 metre 138.36
2241 Good earth cum 129.71
2242 Dump manure cum 112.79
2260 Brick aggregate cum 112.79
2261 Sand cum 103.77
2262 Fly ash cum 103.77
2264 Rubbish cum 103.77
2268 Marble dust and marble chips cum 103.77
2271 G.I. pipes below 100 mm dia tonne 92.24
2272 Stainless Steel pipe below 100 mm dia tonne 92.24
2273 A.C.sheet and accessories tonne 92.24
2275 R.C.C. pipes 100 mm dia 100 metre 226.82
BASIC RATES : 0.4 CARRIAGE CODES 61

No.
2299 R.C.C. pipes 450 & 500 mm dia 100 metre 2520.19
2302 G.I.sheet and accessories tonne 92.24
2303 R.C.C. pipes 600, 700, 750 & 800 mm dia 100 metre 3780.28
2308 Plaster of paris tonne 92.24
2309 Cast iron fittings tonne 92.24
2311 Red bajri cum 103.77
2314 Barbed wire tonne 92.24
2317 Sludge cum 112.79
2319 Spun iron S & S pipes 100 mm dia 100 metre 226.82
2329 Spun iron S & S pipes 600mm dia 100 metre 3780.28
2330 C.I. pipes 500 mm dia 100 metre 2520.19
2335 Jamuna sand cum 103.77
2336 RCC pipe above 1200 mm dia & up to 1800 mm dia 100 metre 7560.57
2341 Pig lead tonne 92.24
2342 Solvent/ Diesel quintal 10.38
2343 Ductile iron pipes (k7) 100 mm dia 100 metre 226.82
2344 Cast iron pipes 150 mm dia 100 metre 378.03

No.

SUB HEAD : 1.0
CARRIAGE OF MATERIALS
64
BASIC RATES (SH: 1.0 CARRIAGE OF MATERIALS)

No.
0084 Hire charges of diesel truck - 9 tonne (witout POL) day 1500.00
0128 Mate day 617.00
SUB HEAD : 1.0 CARRIAGE OF MATERIALS 65

1.0 CARRIAGE OF MATERIALS
Note:- These rates are inclusive of Contractor's profit and over heads but exclusive of GST
1.1 By Mechanical Transport including loading,unloading and stacking
Item Materials Unit Rate i/c 15% CP & OH Remarks

Code 1 km 2 km 3 km 4 km 5 km Beyond Beyond Beyond
5 km 10 km 20 km
upto 10 upto 20 per
km per km per addl.
km km km
1 2 3 4 5 6 7 8 9 10 11 12
1.1.1 Lime, moorum, building cum 104.94 119.54 134.00 147.91 161.46 12.16 10.11 8.35 The rates will be
rubbish applicable to net
1.1.2 Earth cum 131.17 149.43 167.50 184.89 201.83 15.20 12.63 10.44 quantities after
deduction of
1.1.3 Manure or sludge cum 114.06 129.94 145.65 160.78 175.50 13.22 10.99 9.08 prescribed percent-
1.1.4 Excavated rock cum 209.88 239.09 267.99 295.83 322.93 24.33 20.21 16.70 age for voids ment-
ioned in the specific-
1.1.5 Sand, stone aggregate cum 104.94 119.54 134.00 147.91 161.46 12.16 10.11 8.35
ation under sub-head
below 40 mm nominal size
"Carriage of Materials"
1.1.6 Stone aggregate 40 mm cum 114.06 129.94 145.65 160.78 175.50 13.22 10.99 9.08
nominal size and above
1.1.7 Soling stone cum 123.46 140.64 157.64 174.02 189.96 14.31 11.89 9.82
1.1.8 Bricks 1000 Nos. 279.83 318.78 357.32 394.44 430.57 32.43 26.95 22.26
1.1.9 Brick Tiles 1000 Nos. 167.90 191.27 214.39 236.66 258.34 19.46 16.17 13.36
1.1.10 Cement, stone blocks, tonne 93.28 106.26 119.11 131.48 143.52 10.81 8.98 7.42
G.I.. C.I., A.C., & C.C.
pipes below 100 mm dia
and other heavy materials

5 km 10 km 20 km
upto 10 upto 20 per
km per km per addl.
km km km
1 2 3 4 5 6 7 8 9 10 11 12
1.1.11 Steel tonne 93.28 106.26 119.11 131.48 143.52 10.81 8.98 7.42
1.1.12 Timber cum 119.93 136.62 153.14 169.05 184.53 13.90 11.55 9.54
1.1.13 Tar Bitumen tonne 104.94 119.54 134.00 147.91 161.46 12.16 10.11 8.35
1.1.14 Solvent, diesel qtl 10.49 11.95 13.40 14.79 16.15 1.22 1.01 0.83
1.1.15 Steam coal tonne 119.93 136.62 153.14 169.05 184.53 13.90 11.55 9.54
1.1.16 S.W. pipe
1.1.16.1 100 mm dia 100 m 139.92 159.39 178.66 197.22 215.29 16.22 13.48 11.13
1.1.16.2 150 mm dia 100 m 279.83 318.78 357.32 394.44 430.57 32.43 26.95 22.26
1.1.16.3 200 mm dia 100 m 466.39 531.30 595.54 657.40 717.62 54.06 44.92 37.11
1.1.16.5 250 mm dia 100 m 799.52 910.80 1020.93 1126.97 1230.20 92.67 77.01 63.61
1.1.16.6 300 mm dia 100 m 999.40 1138.50 1276.16 1408.71 1537.76 115.84 96.26 79.51
1.1.16.7 350 mm dia 100 m 1399.17 1593.90 1786.62 1972.19 2152.86 162.17 134.76 111.32
1.1.16.8 400 mm dia 100 m 1998.81 2277.00 2552.32 2817.42 3075.51 231.67 192.52 159.03
1.1.16.9 450 mm dia 100 m 2543.94 2898.00 3248.40 3585.80 3914.29 294.85 245.02 202.40
1.1.16.10 500 mm dia 100 m 2798.33 3187.80 3573.24 3944.39 4305.72 324.34 269.52 222.64
1.1.16.11 600 mm dia 100 m 3497.92 3984.75 4466.55 4930.48 5382.14 405.42 336.90 278.30
1.1.17 R.C.C. pipe,
A.C. pipes, steel
cylinder, R.C. pipes,
S.C.I. pipes, C.I. pipes
and unreinforced
cement pipes

5 km 10 km 20 km
upto 10 upto 20 per
km per km per addl.
km km km
1 2 3 4 5 6 7 8 9 10 11 12
1.1.17.1 100 mm dia 100 m 229.37 261.30 292.89 323.31 352.93 26.59 22.09 18.25
1.1.17.2 125 mm dia 100 m 306.39 349.03 391.23 431.87 471.43 35.51 29.51 24.38
1.1.17.3 150 mm dia 100 m 382.29 435.49 488.15 538.85 588.21 44.31 36.82 30.42
1.1.17.4 200 mm dia 100 m 621.85 708.40 794.05 876.53 956.83 72.08 59.89 49.48
1.1.17.5 250 mm dia 100 m 883.68 1006.67 1128.39 1245.60 1359.70 102.42 85.11 70.31
1.1.17.6 300 mm dia 100 m 1092.25 1244.26 1394.71 1539.57 1680.61 126.60 105.20 86.90
1.1.17.7 350 mm dia 100 m 1529.14 1741.97 1952.59 2155.40 2352.85 177.23 147.28 121.66
1.1.17.8 400 mm dia 100 m 2085.20 2375.41 2662.62 2939.18 3208.43 241.68 200.84 165.90
1.1.17.9 450 mm & 100 m 2548.57 2903.28 3254.32 3592.34 3921.42 295.39 245.47 202.77
500 mm dia
1.1.17.10 600, 700, 750 & 100 m 3822.86 4354.92 4881.48 5388.50 5882.12 443.09 368.20 304.15
800 mm dia
1.1.17.11 900 mm dia 100 m 5734.29 6532.38 7322.22 8082.76 8823.19 664.63 552.30 456.23
1.1.17.12 1000, 1100 & 100 m 7645.72 8709.84 9762.96 10777.01 11764.25 886.17 736.40 608.31
1200 mm dia

No.
1.1.18 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport
including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete
as per directions of Engineer-in-charge. cum 284.60
Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying
motor vehicle of 3.5 cum or more.

1.0 CARRIAGE OF MATERIALS
Note:- These rates are inclusive of Contractor's profit and over heads but exclusive of GST
1.2 By Manual Labour including loading, unloading and stacking for lead less than 0.50 KM
Code Material Unit Cost of carriage Every additional Remarks

No. inclusing loading, lead of 50 metre
unloading & or part thereof
stacking for first beyond 1st 50
50 metres metre upto 9
( ) such additional
lead ( )
1 2 3 4 5 6
1.2.1 Lime, moorum, cum 140.62 30.62 The rates will be
building rubbish applicable to net
quantities after deduction
1.2.2 Earth cum 175.78 38.27
of precribed percentage
1.2.3 Manure or sludge cum 152.85 33.28 for voids mentioned in the
specification under
1.2.4 Excavated rock cum 281.25 61.24 subhead "Carriage of
1.2.5 Sand, stone aggregate cum 175.78 38.27 Materials"
below 40 mm nominal
size
1.2.6 Stone aggregate 40 mm cum 190.03 41.38
nominal size and above
1.2.7 Soling stone cum 206.80 45.03
1.2.8 Bricks 1000 Nos 328.12 71.44
1.2.9 Brick Tiles 1000 Nos 205.08 44.65
1.2.10 Steam Coal tonne 164.06 35.72
1.2.11 Stone blocks,G.I.,C.I. tonne 128.34 18.83
Stainless Steel pipes
below 100 mm dia and
other heavy material
1.2.12 Cement tonne 101.80 14.94
1.2.13 Steel tonne 218.65 32.09
1.2.14 Timber cum 140.56 20.63
1.2.15 Tar, bitumen etc. tonne 128.34 18.83
1.2.16 S.W. pipe The length of S.W. pipes
will be measured
1.2.16.1 100 mm dia 100 m 256.90 37.70
exclusive of the internal
1.2.16.2 150 mm dia 100 m 422.29 61.97 depth of sockets.
1.2.16.3 200 mm dia 100 m 590.95 86.72

1.2.16.5 250 mm dia 100 m 983.94 144.38

1 2 3 4 5 6
No.
1.2.16.6 300 mm dia 100 m 1405.63 206.26
1.2.16.7 350 mm dia 100 m 1967.88 288.77
1.2.16.8 400 mm dia 100 m 2459.85 360.96
1.2.16.9 450 mm dia 100 m 2981.64 437.52
1.2.16.10 500 mm dia 100 m 3644.22 534.75
1.2.16.11 600 mm dia 100 m 4472.45 656.28
1.2.17 R.C.C. pipes, Steel
cylinder, R.C. pipes,
C.I. pipes, and
unreinforced
cement pipes
1.2.17.1 100 mm dia 100 m 346.86 50.90 The length of the flanged or
plain ended concrete, R.C.C.
1.2.17.2 125 mm dia 100 m 424.42 62.28 pipes, Steel cylinders, R.C.
1.2.17.3 150 mm dia 100 m 488.71 71.71 pipes and C.I. pipes shall be
measured overall. The length
1.2.17.4 200 mm dia 100 m 733.37 107.61 of socketed pipes shall be
1.2.17.5 250 mm dia 100 m 1289.00 189.15 measured exclusive of inter-
nal depth of sockets.
1.2.17.6 300 mm dia 100 m 1613.02 236.69
1.2.17.7 350 mm dia 100 m 2306.11 338.40
1.2.17.8 400 mm dia 100 m 2683.47 393.77
1.2.17.9 450 mm & 100 m 3577.96 525.03
500 mm dia
1.2.17.10 600, 700, 750 & 100 m 3935.76 577.53
800 mm dia

Code
Code Description Description Unit Rate Unit
Remarks Rate
No.
No.
1 2 3 4 5
1.3 Loading in or unloading cement from tonne 104.90
the railway wagons at siding and
carrying the same from or into
godowns adjacent to the siding, in-
cluding stacking the same properly
in rows upto any height as per di-
rection of Engineer-in-charge,
sweeping the wagons and screen-
ing the swept cement and filling in
bags complete.
1.4 Loading in or unloading from the
railway wagons as per direction of
1.4.1 Steel tonne 155.45 The rates will be applicable in
all cases whether materials are
unloaded or loaded from Railway
siding or directly unloaded on
or loaded from transport.
1.4.2 G.I., C.I., R.C.C. or C.C. pipes upto tonne 92.20
500 mm dia and similar heavy
materials
1.4.3 Heavy materials where each piece tonne 165.15 No deduction shall be from
or bundle, crate or case weighs more carriage rates for direct unloading
than one tonne and R.C.C., C.I. and or loading.
concrete pipes above 500 mm dia.

SUB HEAD : 2.0
EARTH WORK
72
BASIC RATES (SH: 2.0 EARTH WORK)

No.
0128 Mate day 617.00
0325 Blasting powder kg 40.00
0326 Blasting fuse (fuse wire) each 15.00
7022 Chlorpyriphos 20% E.C. / Lindane 20% E.C. litre 150.00
SUB HEAD : 2.0 EARTH WORK 73

2.0 E A R T H W O R K

No.
2.1 Earth work in surface excavation not exceeding 30 cm in depth but
exceeding 1.5 m in width as well as 10 sqm on plan including getting
out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as
directed by Engineer-in- Charge:
2.1.1 All kinds of soil sqm 92.55
2.2 Earth work in rough excavation, banking excavated earth in layers not
exceeding 20cm in depth, breaking clods, watering, rolling each layer
with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and
top-most layer with power roller of minimum 8 tonnes and dressing up in
embankments for roads, flood banks, marginal banks and guide banks or
filling up ground depressions, lead upto 50 m and lift upto 1.5 m :
2.2.1 All kinds of soil cum 746.80
2.3 Banking excavated earth in layers not exceeding 20 cm in depth, breaking
clods, watering, rolling each layer with ½ tonne roller, or wooden or
steel rammers, and rolling every 3rd and top-most layer with power
roller of minimum 8 tonnes and dressing up, in embankments for roads,
flood banks, marginal banks, and guide banks etc., lead upto 50 m and
lift upto 1.5 m :
2.4 Deduct for not rolling with power roller of minimum 8 tonnes for banking
excavated earth in layers not exceeding 20 cm in depth. cum 4.30
2.5 Deduct for not watering the excavated earth for banking cum 33.00
2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual
means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10
sqm on plan) including getting out and disposal of excavated earth lead
upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
2.7 Earth work in excavation by mechanical means (Hydraulic excavator)/
manual means over areas (exceeding 30 cm in depth, 1.5 m in width as
well as 10 sqm on plan) including getting out and disposal of excavated
earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-
charge.
2.7.1 Ordinary rock cum 352.45
2.7.2 Hard rock (requiring blasting) cum 609.65
2.7.3 Hard rock (blasting prohibited) cum 1016.20
2.8 Earth work in excavation by mechanical means (Hydraulic excavator) /
manual means in foundation trenches or drains (not exceeding 1.5 m in
width or 10 sqm on plan), including dressing of sides and ramming of
bottoms, lift upto 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a lead of 50 m.
2.8.1 All kinds of soil. cum 252.30

No.
2.9 Excavation work by mechanical means (Hydraulic excavator)/ manual

means in foundation trenches or drains (not exceeding 1.5m in width or
10 sqm on plan), including dressing of sides and ramming of bottoms,
lift upto 1.5 m, including getting out the excavated soil and disposal of
surplus excavated soils as directed, within a lead of 50 m.
2.9.1 Ordinary rock cum 448.15
2.9.2 Hard rock (requiring blasting) cum 729.00
2.9.3 Hard rock (blasting prohibited) cum 1080.55
2.10 Excavating trenches of required width for pipes, cables, etc including
excavation for sockets, and dressing of sides, ramming of bottoms, depth
upto 1.5 m, including getting out the excavated soil, and then returning
the soil as required, in layers not exceeding 20 cm in depth, including
consolidating each deposited layer by ramming, watering, etc. and
disposing of surplus excavated soil as directed, within a lead of 50 m :
2.10.1 All kinds of soil
2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. metre 223.00
2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not
exceeding 300 mm dia metre 364.20
2.10.1.3 Pipes, cables etc. exceeding 300 mm dia but not
exceeding 600 mm metre 568.60
2.11 Extra for excavating trenches for pipes, cables etc. in all kinds of soil for
depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over
corresponding basic item for depth upto 1.5 metre). metre 127.00 %
2.12 Extra for excavating trenches for pipes, cables, etc, in all kinds of soil
for depth exceeding 3 m in depth, but not exceeding 4.5 m. (Rate is
over corresponding basic item for depth upto 1.5 metre.) metre 315.05 %
2.13 Excavating trenches of required width for pipes, cables, etc, including
excavation for sockets, depth upto 1.5 m, including getting out the
excavated materials, returning the soil as required in layers not exceeding
20 cm in depth, including consolidating each deposited layers by ramming,
watering etc., stacking serviceable material for measurements and disposal
of unserviceable material as directed, within a lead of 50 m :
2.13.1 Ordinary rock
2.13.1.1 Pipes, cables etc. not exceeding 80 mm dia metre 323.85
2.13.1.2 Pipes, cables etc. exceeding 80 mm dia but not
2.13.1.3 Pipes, cables exceeding 300 mm dia but not
2.13.2 Hard rock (requiring blasting)
2.13.2.2 Pipes, cables etc. exceeding 80 mm dia but
not exceeding 300 mm dia metre 1135.60

No.
2.13.3 Hard rock (blasting prohibited)

2.14 Extra for excavating trenches for pipes, cables, etc. in ordinary/hard
rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over
corresponding basic item for depth upto 1.5 metre) metre 103.60%
2.15 Extra for excavating trenches for pipes, cables, etc. in ordinary/hard
rock exceeding 3m in depth but not exceeding 4.5 m. (Rate is over
correspondingbasic item for depth upto 1.5 metre) metre 255.60%
2.16 Close timbering in trenches including strutting, shoring and packing
cavities (wherever required) complete. (Measurements to be taken of
the face area timbered).
2.16.1 Depth not exceeding 1.5 m sqm 129.95
2.16.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 141.20
2.16.3 Depth exceeding 3 m but not exceeding 4.5 m sqm 166.55
2.17 Close timbering in case of shafts, wells, cesspits, manholes and the
like including strutting, shoring and packing cavities (wherever required)
etc. complete. (Measurements to be taken of the face area timbered).
2.18 Close timbering over areas including strutting, shoring and packing
cavities (wherever required) etc. complete. (Measurements to be taken
of the face area timbered):
2.19 Extra for planking, strutting and packing materials for cavities (in close
timbering) if required to be left permanently in position. (Face area of
timber permanently left to be measured). sqm 1593.75
2.20 Open timbering in trenches including strutting and shoring complete
(measurements to be taken of the face area timbered):

No.
2.21 Open timbering in case of shafts, wells, cesspits, manholes and the
like including strutting and shoring complete (Measurements to be taken
of the face area timbered):
2.22 Open timbering over areas including strutting, shoring etc. complete.
(Measurements to be taken of the face area timbered):
2.23 Extra for planking and strutting in open timbering if required to be left
permanently in position. (Face area of the timber permanently left to be
measured). sqm 820.55
2.24 Extra rates for quantities of works, executed:
2.24.1 In or under water and/or liquid mud, including pumping out metre
water as required depth 20%
2.24.2 In or under foul position, including pumping out water as metre
required depth 25%
Note for item no. 2.24:- The extra percentage rate is applicable in respect
of each item but limited to quantities of work executed in these difficult
conditions. The unit, namely, metre depth, to be considered for payment,
shall be the depth measured from the sub soil water level up to the
centre of gravity of the qty executed in difficult conditions. The depth
shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as
0.10 m and less than 0.05 m ignored.
2.25 Filling available excavated earth (excluding rock) in trenches, plinth,
sides of foundations etc. in layers not exceeding 20cm in depth,
consolidating each deposited layer by ramming and watering, lead up
to 50 m and lift upto 1.5 m. cum 219.65
2.25(a) Excavating, supplying and filling of local earth (including royalty)
by mechanical transport upto a lead of 5km also including
ramming and watering of the earth in layers not exceeding 20
cm in trenches, plinth, sides of foundation etc. complete. cum 323.90
2.26 Extra for every additional lift of 1.5 m or part thereof in excavation /
banking excavated or stacked materials.
2.26.2 Ordinary or hard rock cum 162.10
2.27 Supplying and filling in plinth with sand under floors, including watering,
ramming, consolidating and dressing complete. cum 1953.05

No.
2.28 Surface dressing of the ground including removing vegetation and in-
equalities not exceeding 15 cm deep and disposal of rubbish, lead up
to 50 m and lift up to 1.5 m.
2.29 Ploughing the existing ground to a depth of 15 cm to 25 cm and watering
the same.
2.30 Excavating holes more than 0.10 cum & upto 0.5 cum including getting
out the excavated soil, then returning the soil as required in layers not
exceeding 20cm in depth, including consolidating each deposited layer
by ramming, watering etc, disposing of surplus excavated soil, as
directed within a lead of 50 m and lift upto 1.5 m.
2.30.1 All kinds of soil each 79.30
2.30.2 Ordinary rock each 138.05
2.30.3 Hard rock (requiring blasting) each 222.30
2.30.4 Hard rock (blasting prohibited) each 327.80
2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood,
trees and saplings of girth up to 30 cm measured at a height of 1 m
above ground level and removal of rubbish up to a distance of 50 m
outside the periphery of the area cleared. sqm 12.55
2.32 Clearing grass and removal of the rubbish up to a distance of 50 m
outside the periphery of the area cleared. sqm 6.40
2.33 Felling trees of the girth (measured at a height of 1 m above ground
level), including cutting of trunks and branches, removing the roots and
stacking of serviceable material and disposal of unserviceable material.
2.33.1 Beyond 30 cm girth upto and including 60 cm girth each 380.60
2.33.4 Above 240 cm girth each 15749.95
2.34 Supplying chemical emulsion in sealed containers including delivery as
specified.
2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 200.85
2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL
anti-termite treatment (excluding the cost of chemical emulsion) :
2.35.1 Along external wall where the apron is not provided using
chemical emulsion @ 7.5 litres / sqm of the vertical surface of
the substructure to a depth of 300mm including excavation
channel along the wall & rodding etc. complete:
2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1%
concentration metre 28.25

No.
2.35.2 Along the external wall below concrete or masonry apron us-
ing chemical emulsion @ 2.25 litres per linear metre includ-
ing drilling and plugging holes etc.:
2.35.2.1 With Chlorpyriphos/ Lindane E.C. 20% with 1%
2.35.3 Treatment of soil under existing floors using chemical emul-
sion @ one litre per hole, 300 mm apart including drilling 12
mm diameter holes and plugging with cement mortar 1 :2
(1 cement : 2 Coarse sand) to match the existing floor:
2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1%
concentration sqm 227.05
2.35.4 Treatment of existing masonry using chemical emulsion @
one litre per hole at 300 mm interval including drilling holes at
45 degree and plugging them with cement mortar 1:2 (1
cement : 2 coarse sand) to the full depth of the hole :
2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1%
2.35.5 Treatment at points of contact of wood work by chemical
emulsion Chlorpyriphos/ Lindane (in oil or kerosene based
solution) @ 0.5 litres per hole by drilling 6 mm dia holes at
downward angle of 45 degree at 150 mm centre to centre and
sealing the same. metre 254.00
2.36 Extra for levelling & neatly dressing of disposed soil completely as
directed by Engineer-in-charge. cum 66.35
2.37 Supply and stacking of Fly ash conforming to IRC- 58 at site, including
carriage, loading , unloading & stacking up to any lead (measured stacks
will be reduced by 20% for payment). cum 152.20
2.38 Filling with available fly ash and earth (excluding rock) in trenches or
embankment in layers (each layer should not exceed 15 cm), with
intermediate layer of compacted earth (Soil density of 98%) after every
four layers of compacted depth of fly ash, sides & top layer of filling
shall be done with earth having total minimum compacted thickness
30 cm or as decided by Engineer -in-charge, including compacting each
layer by rolling/ ramming and watering, all complete as per drawing and
direction of Engineer -in - charge. cum 219.65

SUB HEAD : 3.0
MORTAR
80
BASIC RATES (SH : 3.0 MORTAR)

No.
0811 Mud (dry) cum 165.00
2261 Carriage of Fine sand (1 Part badarpur sand : 2 Parts
Jamuna sand) cum 103.77
SUB HEAD : 3.0 MORTAR 81

3.0 MORTAR
Note : These rates are exclusive of GST, water charges, overheads and contractor's profit.

No.
3.1 Cement mortar 1:1 (1 cement : 1 fine sand) cum 6390.60
3.12 Cement mortar 1:2 (1 cement : 2 stone dust). cum 5108.05
3.15 White cement mortar 1:2 (1 white cement : 2 marble dust). cum 9393.35
3.18 Mud mortar cum 737.00
3.19 Mortar in lime, surkhi (50% red and 50% light yellow) and marble
dust 1:1.5:0.5 cum 2821.15
SUB HEAD : 3.0 MORTAR 82

SUB HEAD : 4.0
CONCRETE WORK
83
BASIC RATES (SH: 4.0 CONCRETE WORK)
No.
SUB HEAD : 4.0 CONCRETE WORK 84

No.
2261 Carriage of Fine sand (1 Part badarpur sand : 2 Parts
Jamuna sand) cum 103.77
7334 Prop 2 m ( 2-3.5 m) each 635.00
8732 Synthetic ployster triangular fibre of length 12 mm, effective
diameter 10-40 microns and specific gravity of 1.34 to 1.40 kg 365.00

4.0 CONCRETE WORK

No.
CEMENT CONCRETE (CAST IN SITU)
4.1 Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shuttering - All work up to plinth
level :
4.1.2 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone
4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone
4.1.4 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone
4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone
4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone
4.1.11 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate
40 mm nominal size) cum 5225.15
4.1.12 1:2:3½:9 (1 ordinary portland cement : 2 Fly ash : 3½ coarse
sand (zone-III) : 9 graded stone aggregate 40 mm nominal size) cum 5629.15
4.1.13 1:2½:4:11 (1 ordinary portland cement : 2½ fly ash : 4 coarse
sand(zone-III) : 11 graded stone aggregate 40 mm nominal size) cum 5301.45
4.2 Providing and laying cement concrete in retaining walls, return walls,
walls (any thickness) including attached pilasters, columns, piers,
abutments, pillars, posts, struts, buttresses, string or lacing courses,
parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,
sunken floor etc., up to floor five level, excluding the cost of centering,
shuttering and finishing:
4.2.2 1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone
aggregate 20 mm nominal size). cum 8976.45
4.3 Centering and shuttering including strutting, propping etc. and removal
of form work for :
4.3.1 Foundations, footings, bases for columns sqm 284.85

No.
4.3.2 Retaining walls, return walls, walls (any thickness) including

attached pilasters, buttresses, plinth and string courses
fillets, kerbs and steps etc. sqm 609.30
4.3.3 Columns, piers, abutments, pillars, posts and struts sqm 733.70
4.4 Providing and laying cement concrete in kerbs, steps and the like at or
near ground level excluding the cost of centering, shuttering and
finishing.
4.4.1 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone
CEMENT CONCRETE PRECAST
4.5 Providing and fixing up to floor five level precast cement concrete string
or lacing courses, copings, bed plates, anchor blocks, plain window
sills, shelves, louvers, steps, stair cases, etc., including hoisting and
setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand),
cost of required Centering complete.
4.5.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone
aggregate 20mm nominal size) cum 8537.75
4.6 Providing and fixing at or near ground level precast cement concrete in
kerbs, edgings etc. as per approved pattern and setting in position
with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost
of required centering, shuttering complete.
4.7 Providing and fixing up to floor five level precast cement concrete solid
block, including hoisting and setting in position with cement mortar
1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering
complete :
4.8 Providing and fixing up to floor five level precast cement concrete hollow
block, including hoisting and setting in position with cement mortar
1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering
complete.
4.8.1 1:1½:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone
aggregate 20 mm nominal size) . cum 11346.05
4.9 Precasting and placing in position 125 mm dia Bollards 600 mm high of
required shape including providing M.S. Pipe Sleeve 50 mm dia 300
mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long
with 150x150x6mm M.S. plate welded at bottom and embedded 150mm
in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6
graded stone aggregate 20 mm nominal size), including necessary
excavation of size 250x250x450mm deep for the same in bitumen/
concrete pavement at specified spacing. each 723.05
DAMP-PROOF COURSE
4.10 Providing and laying damp-proof course 40mm thick with cement
concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone
aggregate 12.5mm nominal size) sqm 347.90

No.
4.11 Providing and laying damp-proof course 50mm thick with cement
concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone
aggregate 20mm nominal size). sqm 418.90
4.12 Extra for providing and mixing water proofing material in cement concrete per 50kg
work in doses by weight of cement as per manufacturer's specification. cement 56.55
4.13 Providing & applying a coat of residual petroleum bitumen of grade of
VG-10 of approved quality using 1.7kg per square metre on damp proof
course after cleaning the surface with brushes and finally with apiece
of cloth lightly soaked in kerosene oil. sqm 110.00
MISCELLANEOUS
4.14 Extra for concrete work in superstructure above floor V level for each
four floors or part thereof. cum 1119.85
4.15 Extra for laying concrete in or under water and/or liquid mud including cum per
cost of pumping or bailing out water and removing slush etc. complete. metre depth 794.65
Note for item No. 4.15 :- The quantity will be calculated by multiplying
the depth measured from the sub-soil water level up to centre of gravity
of concrete under sub-soil water level with quantity of concrete in cum
executed under sub-soil water. The depth of centre of gravity shall be
reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and
less than 0.05m ignored.
4.16 Extra for laying concrete in or under foul positions. cum 336.55
4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement
: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal
size) over 75mm thick bed of dry brick ballast 40 mm nominal size,
well rammed and consolidated and grouted with fine sand, including
necessary excavation, levelling & dressing & finishing the top smooth. sqm 614.05
4.18 Extra for addition of synthetic Polyester triangular fibre of length 12mm,
effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in
cement concrete/RCC/Flooring/water retaining structures by using per bag
125gms of synthetic Polyester triangular fibre for 50 Kg cement used of 50kg of
as per directions of Engineer-in-Charge. cement 61.05
4.19 Providing and laying in position ready mixed plain cement concrete,
using fly ash and cement content as per approved design mix and
manufactured in fully automatic batching plant and transported to site
of work in transit mixer for all leads, having continuous agitated mixer,
manufactured as per mix design of specified grade for plain cement
concrete work, including pumping of R.M.C. from transit mixer to site
of laying and curing, excluding the cost of centering, shuttering and
finishing, including cost of curing, admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and durability as per
direction of the Engineer-in-charge.
Note : (1) Excess/less cement used than specified in this item is
payable/recoverable separately. (2) Fly ash conforming to grade I of IS
3812 (Part-1) only be used as part replacement of OPC as per IS : 456.
Uniform blending with cement is to be ensured in accordance with
clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC.

No.
4.19.1 All works upto plinth level:

4.19.1.1 M-15 grade plain cement concrete (cement
content considered @ 240 kg/cum) cum 7738.20
4.19.2 All works above plinth and upto floor V level:
content considered @ 240 kg /cum) cum 8860.80
Note :- The above item shall be used judiciously where specified quality
of Fly Ash is available for mixing in concrete. Also, the guidelines issued
by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102
dated 9th April 2009 shall be followed in such cases.
4.20 Providing and laying in position ready mixed plain cement concrete,
with cement content as per approved design mix and manufactured in
fully automatic batching plant and transported to site of work in transit
mixer for all leads, having continuous agitated mixer, manufactured as
per mix design of specified grade for plain cement concrete work,
including pumping of R.M.C. from transit mixer to site of laying and
curing, excluding the cost of centering, shuttering and finishing,
including cost of curing, admixtures in recommended proportions as
per IS : 9103 to accelerate/ retard setting of concrete, improve workability
without impairing strength and durability as per direction of the Engineer-
in-charge.
Note : 1) Excess/less cement used than specified in this item is
payable/recoverable separately.
4.20.1 All works upto plinth level :
4.20.2 All works above plinth and upto floor V level :
4.20.2.1 M-15 grade plain cement concrete. (cement

SUB HEAD : 5.0
REINFORCED CEMENT
CONCRETE
90
BASIC RATES (SH: 5.0 REINFORCED CEMENT CONCRETE)
No.
0052 Front end loader 1 cum bucket capacity (incl POL) hour 900.00
0082 Excavation of Diaphragm wall by Mechanical Grab sqm 1300.00
0128 Mate day 617.00
0236 Multi purpose fibre (high impact poly propelene reinforced)
cement board 6 mm thick sqm 210.00
0242 6mm thick multipurpose cement bonded wood particle board
SUB HEAD -5.0 REINFORCED CEMENT CONCRETE 91

No.
0339 Flame retardant face insulating, Impregnated fibre board 12 mm
thick sqm 375.00
0596 Bright finished or black enameled mild steel butt hinges 75x47x
1.70 mm 10 Nos 56.00
0967 Copper plate kg 527.00
1004 Average rate of Mild steel round bars for reinforcement quintal 4500.00
1015 Mild steel expanded metal 20x60 mm strands 3.25 mm wide
1.60 mm thick sqm 280.00
1224 Hard drawn steel wire quintal 4800.00
2261 Carriage of Fine sand (1 Part badarpur sand : 2 Parts Jamuna sand) cum 103.77
SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 92

No.

2391 Strips-Aluminium fluted 3.15 mm thick and 150 mm wide metre 278.00
2392 Strips Aluminium fluted 3.15 mm thick and 200 mm wide metre 370.00
2393 1 mm thick Stainless Steel Cover plate grade 304 kg 275.00
2402 Epoxy adhesive kg 150.00
2447 Hollock ballies 125 mm diameter metre 35.00
7183 Bentonite of 35 kg per pile tonne 2960.00
7324 Spring coil 12 mm each 15.00
7325 Plastic cone 12 mm dia each 17.00

No.

7334 Prop 2 m ( 2-3.5 m) each 635.00
7342 Adjustable span ESO+SI (2.35-3.40) each 1480.00
7343 Adjustable telescopic prop 3 m (2.02-3.75 m) each 955.00
7344 Beam clamp 300-380 mm (450-1070 mm) each set 355.00
7345 Prop 4 m each 910.00
8953 Micro Silica kg 32.00
8954 Stop end tubes for diaphragmwall 600 mm dia. sqm 4.50
8955 Driving end tubes for diaphragm wall 600 mm dia. sqm 72.00

5.0 REINFORCED CEMENT CONCRETE

No.
CAST IN SITU
5.1 Providing and laying in position specified grade of reinforced cement
concrete, excluding the cost of centering, shuttering, finishing and
reinforcement - All work up to plinth level :
5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone
5.2 Reinforced cement concrete work in walls (any thickness), including
attached pilasters, buttresses, plinth and string courses, fillets, columns,
pillars, piers, abutments, posts and struts etc. above plinth level up to
floor five level, excluding cost of centering, shuttering, finishing and
reinforcement :
5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone
5.3 Reinforced cement concrete work in beams, suspended floors, roofs having
slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain
window sills, staircases and spiral stair cases above plinth level up to
floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). cum 9763.80
5.4 Providing and laying up to floor five level reinforced cement concrete in
kerbs, steps and the like excluding the cost of centering, shuttering,
finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
5.5 Reinforced cement concrete work in arches, archribs, domes, vaults,
shells, folded plate and roofs having slope more than 15° up to floor five
level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3
graded stone aggregate 20 mm nominal size). cum 10289.00
5.6 Reinforced cement concrete work in chimneys, shafts, up to floor five
level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
5.7 Reinforced cement concrete work in well-steining, excluding the cost of
centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement
: 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal
size). cum 7270.30
5.8 Reinforced cement concrete work in vertical and horizontal fins individually
or forming box louvers, facias and eaves boards above plinth level up to
floor five level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1½:3 (1 cement : 1½ coarse sand(zone-III) : 3
graded stone aggregate 20mm nominal size). cum 8550.25

No.
FORM WORK
5.9 Centering and shuttering including strutting, propping etc. and removal
of form for :
5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 284.85
5.9.2 Walls (any thickness) including attached pilasters, butteresses,
plinth and string courses etc. sqm 609.30
5.9.3 Suspended floors, roofs, landings, balconies and access
platform sqm 693.05
5.9.4 Shelves (Cast in situ) sqm 693.05
5.9.5 Lintels, beams, plinth beams, girders, bressumers and
cantilevers sqm 552.05
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 733.70
5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 622.35
5.9.8 Spiral staircases (including landing) sqm 600.00
5.9.9 Arches, domes, vaults up to 6 m span sqm 1713.20
5.9.10 Extra for arches, domes, vaults exceeding 6 m span sqm 560.65
5.9.11 Chimneys and shafts sqm 609.30
5.9.12 Well steining sqm 246.40
5.9.13 Vertical and horizontal fins individually or forming box louvers
band, facias and eaves boards sqm 1023.55
5.9.14 Extra for shuttering in circular work (20% of respective centering
and shuttering items) sqm 20.00%
5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in
cornices, window sills, string courses, bands, copings, bed
plates, anchor blocks and the like sqm 284.85
5.9.16 Edges of slabs and breaks in floors and walls
5.9.16.1 Under 20 cm wide metre 173.25
5.9.16.2 Above 20 cm wide sqm 737.30
5.9.17 Cornices and mouldings sqm 740.25
5.9.18 Small surfaces such as cantilever ends, brackets and ends
of steps, caps and bases to pilasters and columns and the like sqm 773.70
5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 766.75
5.9.20 Suspended floors, roofs, landings, balconies and access
platform with water proof ply 12 mm thick sqm 779.30
5.9.21 Lintels, beams, plinth beams, girders, bressumers and
cantilevers with water proof ply 12 mm thick sqm 641.60
5.10 Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering
complete as per the direction of Engineer-in-charge.
5.10.1 12 mm dia. & 100 mm length each set 140.80

No.

5.10.4 20 mm dia.& 225 mm length each set 179.60
5.11 Extra for additional height in centering, shuttering where ever required
with adequate bracing, propping etc., including cost of de-shuttering
and decentering at all levels, over a height of 3.5 m, for every additional
height of 1 metre or part thereof (Plan area to be measured).
5.11.1 Suspended floors, roofs, landing, beams and balconies
(Plan area to be measured) sqm 287.50
PRE-CAST RCC
5.12 Providing, hoisting and fixing above plinth level up to floor five level precast
reinforced cement concrete work in string courses, bands, copings,
bed plates, anchor blocks, plain window sills and the like, including the
cost of required centering, shuttering but , excluding cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
5.13 Providing, hoisting and fixing up to floor five level precast reinforced cement
concrete in small lintels not exceeding 1.5m clear span up to floor five
level, including the cost of required centering, shuttering but , excluding
the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-
III) : 3 graded stone aggregate 20 mm nominal size). cum 12464.25
reinforced cement concrete in mouldings as in cornices, windows sills
etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand)
cost of required centering, shuttering but, excluding the cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
reinforced cement concrete in lintels, beams and bressumers, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required
centering and shuttering but , excluding the cost of reinforcement, with
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate
20 mm nominal size) cum 11351.35
reinforced cement concrete in shelves, including setting in cement mortar
1:3 (1cement : 3 coarse sand), cost of required centering, shuttering
and finishing with neat cement punning on exposed surfaces but ,
excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse
reinforced cement concrete in vertical & horizontal fins, individually or
forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse
sand), including the cost of required centering, shuttering but , excluding
the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-
III) : 3 graded stone aggregate 20 mm nominal size). cum 9948.80

No.
5.18 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced
with 1.6 mm dia mild steel wire, including centering and shuttering,
roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:
3 fine sand) etc. complete, excluding plastering of the jambs, sills and
soffits.
5.18.1 50 mm thick sqm 1474.05
5.18.2 40 mm thick sqm 1329.75
5.18.3 25 mm thick sqm 1194.95
ENCASING ROLLED STEEL SECTION
5.19 Encasing rolled steel sections, in beams and columns, with cement
concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone
aggregate 20 mm nominal size), including centering and shuttering
complete but , excluding cost of reinforcement. cum 13020.50
5.20 Encasing rolled steel section in grillages with cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20
mm nominal size), including centering and shuttering but, excluding
cost of expanded metal and hangers. cum 8190.10
5.21 Extra for providing and fixing expanded metal mesh of size 20x60 mm
and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for
encasing of rolled steel sections in beams, columns and grillages,
excluding cost of hangers. sqm 443.95
STEEL REINFORCEMENT
5.22 Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete upto plinth level.
5.22.1 Mild steel and Medium Tensile steel bars Kg 82.10
5.22.2 Hard drawn steel wire Kg 85.60
5.22.3 Cold twisted bars Kg 83.50
5.22.4 Hot rolled deformed bars Kg 83.50
5.22.5 Hard drawn steel wire fabric Kg 92.15
5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 83.50
5.22A Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete above plinth level.
5.22A.1 Mild steel and Medium Tensile steel bars Kg 82.10
5.22A.2 Hard drawn steel wire Kg 85.60
5.22A.3 Cold twisted bars Kg 83.50
5.22A.4 Hot rolled deformed bars Kg 83.50
5.22A.5 Hard drawn steel wire fabric Kg 92.15
5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 83.50

No.
5.22B Steel reinforcement for R.C.C. work ready to use "cut and bend"
rebars of approved make from factory/workshop to construction
site including placing in position and binding all complete upto
plinth level.
5.22B.1 Thermo-Mechanically Treated bars of grade Fe-500D or
more. Kg 77.65
5.22C Steel reinforcement for R.C.C. work ready to use "cut and bend"
rebars of approved make from factory/workshop to construction
site including placing in position and binding all complete above
plinth level.
5.22C.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 77.65
MISCELLANEOUS
5.23 Smooth finishing of the exposed surface of R.C.C. work with 6 mm
thick cement mortar 1:3 (1 Cement : 3 fine sand). sqm 227.35
5.24 Extra for rendering smooth the top of suspended floors, landings and
staircases (treads and risers) with cement mortar 1:2 (1 cement : 2
coarse sand), including a floating coat of neat cement and protecting
the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand
in case of suspended floor and bricks laid in mud mortar in case of
landings and steps, including subsequent removal and cleaning of the
same. sqm 125.10
5.25 Providing and fixing in position copper plate as per design for expansion
joints. Kg 728.20
5.26 Providing and filling in position, blown bitumen in expansion joints. cum 61509.80
5.27 Providing and filling in position bitumen mix filler of proportion 80 kg. of
hot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand for
expansion joints. cum 21054.50
5.28 Providing and fixing in position 12mm thick bitumen impregnated per cm
fiber board conforming to IS: 1838, including cost of primer, sealing depth per
compound Grade-A in expansion joints. 100m 557.65
5.29 Providing and fixing sheet covering over expansion joints with iron screws
as per design.
5.29.1 Non-asbestos fibre cement board 6 mm thick as per IS: 14862.
5.29.1.1 150mm wide metre 190.50
5.29.1.2 200mm wide metre 256.25
5.29.2 Aluminium fluted strips 3.15 mm thick.
5.29.2.1 150 mm wide metre 493.40
5.29.2.2 200 mm wide metre 654.95
5.29.3 Cement bonded wood particle board 6mm thick as per IS : 14276
5.29.3.1 150 mm wide metre 187.35
5.29.3.2 200 mm wide metre 252.00
5.30 Add for plaster drip course/ groove in plastered surface or moulding to
R.C.C. projections. metre 58.90
No.
5.31 Extra for laying reinforced cement concrete in or under water and/ or
liquid mud, including cost of pumping or bailing out water and removing
slush etc., complete. cum 794.65
Note For Item No. 5.31:- The quantity will be calculated by multiplying
the depth measured from the subsoil water level up to the centre of gravity
of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic
metre executed under subsoil water. The depth of centre of gravity shall
be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m
and less than 0.05 m ignored. No extra payment shall be made for placing
reinforcement or centering & shuttering under sub - soil water conditions.
5.32 Extra for laying reinforced cement concrete in or under foul positions. cum 336.55
DESIGN MIX CONCRETE
5.33 Providing and laying in position machine batched and machine mixed
design mix M-25 grade cement concrete for reinforced cement concrete
work, using cement content as per approved design mix, including
pumping of concrete to site of laying but excluding the cost of centering,
shuttering, finishing and reinforcement, including admixtures in
recommended proportions as per IS: 9103 to accelerate, retard setting
of concrete, improve workability without impairing strength and durability
as per direction of Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/
less cement used as per design mix is payable/recoverable separately).
5.33.1 All works upto plinth level cum 7997.30
5.33.2 All works above plinth level upto floor V level cum 9400.85
5.34 Extra for providing richer mixes at all floor levels.
Note:- Excess/less cement over the specified cement content used is
payable /recoverable separately.
5.34.1 Providing M-30 grade concrete instead of M-25 grade BMC/
RMC. (Note:- Cement content considered in M-30 is @
340 kg/cum) cum 69.75
RMC. (Note : Cement content considered in M-35 is @
350 kg/ cum) cum 139.45
RMC.(Note : Cement content considered in M-40 is @
360 kg/ cum) cum 209.20
5.35 Add for using extra cement in the items of design mix over and above
the specified cement content therein. quintal 673.30
5.36 Providing and placing in position precast reinforced cement concrete
waffle units, square or rectangular, as per design and shape for floors
and roofs in 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) : 3 graded
stone aggregate 10 mm nominal size), including flush or deep ruled
pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), making
necessary holes of required sizes for carrying through service lines
etc., providing steel hooks for lifting etc, form work in precasting,
handling, hoisting, centering and erection complete for all floor levels
but, excluding the cost of reinforcement. cum 25483.10
No.
5.37 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having continuous
agitated mixer, manufactured as per mix design of specified grade for
reinforced cement concrete work, including pumping of R.M.C. from
transit mixer to site of laying , excluding the cost of centering, shuttering
finishing and reinforcement, including cost of admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and durability as per
direction of the Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/
cum.Excess/less cement used as per design mix is payable/recoverable
separately).
5.37.1 All works upto plinth level cum 8398.65
5.37.2 All works above plinth level upto floor V level cum 9802.20
5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four
floors or part thereof. cum 280.95
5.40 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using fly ash and cement content as
per approved design mix, and manufactured in fully automatic batching
plant and transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying, excluding the cost of centering,
shuttering, finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate / retard setting
of concrete, improve workability without impairing strength and durability
as per direction of the Engineer - in - charge.
NOTE- (1) Cement content considered in this item is @ 330 kg/cum.
Excess/ less cement used as per design mix is payable/ recoverable
separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be
used as part replacement of OPC as per IS : 456. Uniform blending with
cement to be ensured in accordance with clauses 5.2 and 5.2.1 of
IS:456 -2000 in the items of BMC and RMC.
5.40.1 All works up to Plinth level. cum 8365.80
5.40.2 All works above plinth & up to floor V level. cum 9769.35
Note :- The above item shall be used judiciously where specified quality
of Fly Ash is available for mixing in concrete. Also, the guidelines issued
by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated
9th April 2009 shall be followed in such cases.
5.41 Supplying and applying pre tested and approved water based concrete
curing compound to concrete/ masonry surface, all as per manufacturer’s
specification and direction of Engineer-in-charge.
5.41.1 Non pigmented wet curing compound sqm 53.90

No.
5.42 Providing and fixing parallel threaded couplers conforming to IS code on

“Reinforcement Couplers for Mechanical Splices of Bars for Concrete
Reinforcement - Specification”, to reinforcement bars including threading,
enlargement at connection by forging, protecting the prepared
reinforcement bars and related operations as required to complete the
works per direction of Engineer- in-Charge.
5.42.1 Coupler for 16 mm diameter reinforcement bar each 97.80
5.43 Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm
thick as per design for expansion joints.
5.43.1 200 mm wide. metre 711.90
5.43.2 300 mm wide. metre 1006.25
5.44 Providing and fixing of expansion joint system related with floor location
as per drawings and direction of Engineer-In-Charge. The joints system
will be of extruded aluminum base members, self aligning / self centering
arrangement and support plates etc. as per ASTM B221-02. The system
shall be such that it provides floor to floor /floor to wall expansion control
system for various vertical localtion in load application areas that
accommodates multi directional seismic movement without stress to
it's components. System shall consist of metal profiles with a universal
aluminum base member designed to accommodate various project
conditions and finish floor treatments. The cover plate shall be designed
of width and thickness required to satisfy projects movement and loading
requirements and secured to base members by utilizing manufacturer’s
pre-engineered self- centering arrangement that freely rotates / moves
in all directions. The Self - centering arrangement shall exhibit circular
sphere ends that lock and slide inside the corresponding aluminum
extrusion cavity to allow freedom of movement and flexure in all directions
including vertical displacement. Provision of Moisture Barrier Membrane
in the Joint System to have watertight joint is mandatory requirement
all as per the manufactures design and as approved by Engineer -in-
Charge. (Material shall confirm to ASTM 6063).
5.44.1 Floor Joint of 100 mm gap metre 5594.85
5.45 Providing and fixing of expansion joint system related with wall joint (internal/
external) location as per drawings and direction of Engineer-In- Charge.
The joints shall be of extruded aluminum base members, self aligning /
centering arrangement and support plates as per ASTM B221- 02. The
material shall be such that it provides an Expansion Joints System
suitable for vertical wall to wall/ wall to corner application, both new and
existing construction in office Buildings & complexes with no slipping
down tendency amongst the components of the Joint System. The Joint
System shall utilize light weight aluminum profiles exhibiting minimal

No.
exposed aluminum surfaces mechanically snap locking the multicellular

to facilitate movement. (Material shall confirm to ASTM 6063).
5.45.1 Wall Joint of 100 mm gap metre 4658.30
5.46 Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and
direction of Engineer-In-Charge. The joints shall be of extruded aluminum
base members with, self aligning and self centering arragement support
plates asper ASTM B221-02. The system shall be such that it provides
watertight roof to roof/roof to corner joint cover expansion control system
that is capable of accommodating multidirectional seismic movement
without stress to its components. System shall consist of metal profile
that incorporates a universal aluminum base member designed to
accommodate various project conditions and roof treatments. The cover
plate shall be designed of width and thickness required to satisfy
movement and loading requirements and secured to base members by
utilizing manufacturer’s pre-engineered self-centering arrangement that
freely rotates / moves in all directions. The Self centering arrangement
shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement
and flexure in all directions including vertical displacement. The Joint
System shall resists damage or deterioration from the impact of falling
ice, exposure to UV, airborne contaminants and occasional foot traffic
from maintenance personnel. Provision of Moisture Barrier Membrane
in the Joint System to have water tight joint is mandatory requirement.
(Material shall confirm to ASTM 6063.)
5.46.1 Roof Joint of 100 mm gap metre 5193.45
5.47 Providing and fixing in position factory made precast RCC M-40 fixing
with hold fast embedded in 1:3:6 concrete block for doors and windows
frames having excellent smooth finish as per IS: 6523 with reinforcement
of 3 Nos, 6 mm dia main bars tied with 3 mm M.S stirrups placed @
200 mm C/C and 6 numbers high strength polymer blocks of required
size for fixing hinges including providing 6 no specially designed M.S.
galvanised sleeves for accomodating 6 mm dia fully threaded bolts for
fixing hold fast on vertical members, providing suitable arrangement for
recieving sliding door bolts and tower bolt etc all complete, as per the
direction of Engineer in charge. The frame shall be measured in running
metre correct to two places of decimal.
5.47.1 Door frame 125 mmx 60 mm metre 666.85
5.47.2 Door frame 100 mmx 60 mm metre 617.90
5.47.3 Door frame 85 mmx60 mm metre 592.25
5.48 Providing and laying Reinforced cement concrete for construction of
piers, abutments, portal frames, pier caps and bearing pedestals and
seismic arresters over pier/ abutment caps at all locations with specified

No.
grade using Ordinary Portland Cement (conforming to strength

requirement of IS:8112) including the cost of steel centering and
shuttering etc. complete including testing of materials etc. for casting
pier & pier cap in one/two stage, necessary tools, plants, machinery
and all related operations as required to complete the work as per
drawings and Specifications with all leads, lifts and depths true to level
and position but excluding the cost of providing reinforcement.
(Reinforcement shall be measured and paid separately.)
Note:- Cement content considered in this item is 480 Kg./ Cum. Excess/
less cement used as per design mix is payable/ recoverable separately.
5.48.1 Reinforced Cement Concrete -M-50 cum 7425.00
5.48.2 Reinforced Cement Concrete -M-60 cum 8681.45
5.48.3 Extra for using M -50/ M-60 Grade Self-compacting Cement
Concrete cum 748.60
5.49 Constructing cast-in situ RCC diaphragm wall by providing and laying
machine batched, machine mixed, self compacting, ready mix reinforced
cement concrete, tramie controlled, of M 30 grade using minimum 400
kg. cement per cum of concrete including providing and mixing required
admixtures in recommended proportions as per IS : 9103, as approved
by the Engineer-in-charge, for achieving 150- 200mm slump, for
diaphragm wall having thickness as per approved structural design not
exceeding 600 mm, in pannels of required depth and lengths as per
approved drawing, including constructing necessary guide walls as
required and as specified including boring in all kinds of soils and rocks,
including working in or under water and / or liquid mud, in foul conditions
and pumping or bailing out of water and removing slush, including disposal
of earth/ rock / slush etc. for all leads and all lifts, including preparing,
providing and re-circulating bentonite slurry in the trench as and when
required for all depths, including agitating bentonite slurry during trenching
etc., providing and fixing stop ends or form tubes, upto the required
depth of diaphragm wall including extracting the same after casting,
including chipping off the bentonite adulterated concrete or unsound
concrete up to the cut off level for obtaining the sound concrete, dressing
undulations on the exposed face of diaphragm wall after excavation by
chipping / chiseling etc. including filling the depression/ cavities with
sound concrete etc. complete and as directed by the Engineer-in-charge,
including providing recess for bearing plates and fixing insert boxes for
inclined rock anchors etc. complete as per the specifications and
approved design and as directed by the Engineer-in-charge, but excluding
the cost of reinforcement and inserts. (rates include cost of all inputs of
labour, material and T & P, cost of handling, lifting & placing in position
the reinforcement cage in the trench, including the additional cost of
welding the reinforcement bars etc. involved in the work and all other
incidental expenditure for completing the work as directed by the
Engineer-in-charge), However, the actual area of the diaphragm wall,
correct to two places of decimal, from design bottom level to the design
cut off level (including portion anchored in the rock upto the design
bottom level) only shall be measured for payment.
“Excess/less cement used for design mix including the extra cement
required for under water concreting is payable / recoverable separately. cum 16618.70

SUB HEAD : 6.0
MASONRY WORK
105
BASIC RATES (SH: 6.0 MASONRY WORK)
No.
0357 Polymer modified adhesive mortar kg 15.00
1986 Common burnt clay modular bricks class designation 12.5 1000 Nos 5000.00
7008 F.P.S. (non modular) clay fly ash bricks class designation 7.5 1000 Nos 4800.00
SUB HEAD : 6.0 MASONRY WORK 106

No.
7736 Extruded burnt flyash clay sewer bricks conforming to I.S 4885 1000 Nos 5400.00
7737 Fly ash bricks conforming to I.S. 12894 1000 Nos 4300.00
7738 Calcium Silicate Bricks machine moulded conforming to I.S. 4139 1000 Nos 5400.00
7900 Modular common burnt clay bricks of class designation 7.5 1000 Nos 4000.00
7901 Machine moulded perforated common burnt clay FPS

(non modular) bricks of class designation 12.5 1000 Nos 4700.00
7902 Machine moulded common burnt clay modular perforated bricks

of class designation 12.5 1000 Nos 5200.00
7903 Machine moulded common burnt clay FPS (non modular) bricks
of class designation 12.5 1000 Nos 5000.00
7904 Machine moulded common burnt clay tile bricks of class

designation 12.5 1000 Nos 4900.00
8655 Autoclaved aerated cement (AAC) blocks cum 2600.00
8656 Gypsum panel 666 X 500 X 100 mm size sqm 480.00
8657 Bonding plaster for Gypsum panel kg 25.00

6.0 MASONRY WORK

No.
6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in foundation and plinth in:
6.2 Brick work with common burnt clay modular bricks of class designation
7.5 in foundation and plinth in:
6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). cum 5302.60
6.3 Brick work with common burnt clay machine moulded perforated bricks of
class designation 12.5 conforming to IS: 2222 in superstructure above plinth
level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) :
6.3.1 With F.P.S.(non modular) bricks cum 7722.65
6.3.2 With Modular bricks cum 7501.50
6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in superstructure above plinth level up to floor V level in
all shapes and sizes in :
6.5 Extra for brick work / AAC block masonry / Tile brick masonry in
superstructure above floor V level, for each four floors or part thereof by
mechanical means. cum 236.65
6.6 Extra for forming cavity 5 cm to 11.5 cm wide in cavity walls with
necessary weep and vent holes including use of cores and cost of
providing and fixing bitumastic coated M .S. ties 300 mm long of 25x
3 mm section at not less than 3 ties per sqm as per approved design. sqm 176.25
6.7 Providing half brick masonry with common burnt clay F.P.S. (non modular)
bricks of class designation 7.5 in cement mortar 1:3 (1 Cement : 3
coarse sand) in superstructure for closing cavity 5 to 7.5 cm wide in
cavity wall complete with 10cm / 11.4 cm wide bitumen felt type 3
grade 1. metre 254.00
6.8 Brick work 7 cm thick with common burnt clay F.P.S. (non modular)
brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3
coarse sand) in superstructure above plinth level and upto floor five
level. sqm 749.75
6.9 Brick work in plain arches in superstructure above plinth level and upto
floor five level including centering and shuttering complete for span up
to 6 metres with common burnt clay F.P.S. (non modular) bricks of
class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand). cum 12352.95
6.10 Brick work in gauged arches in superstructure above plinth level and
upto floor five level in cement mortar 1:3 (1 cement : 3 coarse sand)
including centering and shuttering complete, for span up to 6 meters
with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. cum 15361.90

No.
6.11 Extra for additional cost of centering for arches exceeding 6m span
including all shuttering, bolting, wedging and removal (Area of the soffit
to be measured). sqm 560.65
HALF BRICK MASONRY
6.12 Half brick masonry with common burnt clay F.P.S. (non modular) bricks
of class designation 7.5 in foundations and plinth in :
6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) sqm 798.25
6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand) sqm 773.75
6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks
of class designation 7.5 in superstructure above plinth level up to floor
V level.
6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) sqm 956.60
6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 932.10
6.14 Extra for half brick masonry in superstructure, above floor V level for
every four floors or part thereof by mechanical means. sqm 20.95
6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at
every third course of half brick masonry. sqm 80.10
BRICK TILE WORK
6.16 Tile brick masonry with common burnt clay F.P.S. (non modular) tile
bricks of class designation 10 in foundation and plinth in:
6.17 Tile brick masonry with common burnt clay machine moulded tile bricks
of class designation 12.5 conforming to IS : 2690 (Part I) in foundation
and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). cum 9716.75
bricks of class designation 10 in superstructure above plinth level up to
floor V level in cement mortar 1:6 (1 cement : 6 coarse sand). cum 10808.25
bricks of class designation 10 in plain arch work in superstructure
above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4
coarse sand) including centering and shuttering complete. cum 15551.35
bricks of class designation 10 in gauged arch work in superstructure
above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4
coarse sand) including centering and shuttering complete. cum 18567.55
6.22 Tile brick masonry work 5 cm thick with common burnt clay F.P.S.
(non modular) tile bricks of class designation 10 in cement mortar 1:3
(1 cement : 3 coarse sand) in superstructure above plinth and upto
floor five level. sqm 773.25
HONEY COMB WORK
6.23 Honey-comb brick work 10 / 11.4 cm thick with common burnt clay
bricks of class designation 7.5 in super structure above plinth level
upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand). sqm 594.15

No.
6.24 Extra for laying brick work in or under water and/ or liquid mud
including cost of pumping or bailing out water and removing slush etc. cum per
complete. metre depth 794.65
NOTE :- The quantity will be calculated by multiplying the depth
measured from sub - soil water level up to the centre of gravity of brick
work under sub - soil water with the quantity of brick work in cum.
executed under the sub - soil water. The depth of centre of gravity shall
be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m
and less than 0.05 m ignored.
6.25 Extra for laying brick work in or under foul position. cum 336.55
EXPOSED BRICK WALL
6.26 Brick work with common burnt clay selected F.P.S. (non modular) bricks
of class designation 7.5 in exposed brick work including making
horizontal and vertical grooves 10 mm wide 12 mm deep complete in
cement mortar 1:6 (1 cement : 6 coarse sand)
6.26.1 From ground level upto plinth level cum 6324.30
6.26.2 Above plinth level upto floor V level cum 7832.00
6.27 Brick work with common burnt clay modular bricks of class designation
7.5 in exposed brick work including making horizontal and vertical
grooves 10mm wide 12 mm deep complete in cement mortar 1:6 (1
cement : 6 coarse sand).
6.28 Brick work with common burnt clay machine moulded modular bricks
of class designation 12.5 in exposed brick work including making
horizontal and vertical grooves 10 mm wide 12 mm deep complete in
cement mortar 1:6 (1 cement : 6 coarse sand).
6.29 Brick work with common burnt clay machine moulded F.P.S. (non
modular) bricks of class designation 12.5 in exposed brick work including
making horizontal and vertical grooves 10 mm wide 12 mm deep
complete in cement mortar 1:6 (1 cement : 6 coarse sand).
6.30 Brick work with common burnt clay machine moulded perforated F.P.S.
(non modular) bricks of class designation 12.5 conforming IS : 2222 in
exposed brick work including making horizontal and vertical grooves
10mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6
coarse sand).

No.
6.31 Brick work with common burnt clay machine moulded perforated modular
bricks of class designation 12.5 conforming to IS : 2222 in exposed
brick work including making horizontal and vertical grooves 10 mm wide
12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand).
6.32 Brick work with clay flyash F.P.S. (non modular) brick of class
designation 7.5 in superstructure above plinth level up to floor five level
in :
6.34 Brick work with non modular fly ash bricks conforming to IS:12894,
class designation 10 average compressive strength in super structure
above plinth level up to floor V level in :
6.35 Brick work with modular calcium silicate bricks machine moulded
conforming to IS:4139, class designation 10 average compressive
strength in super structure above plinth level up to floor V level in :
6.36 Brick work with modular extruded brunt fly ash clay sewer bricks
(Conforming to IS: 4885 ) in cement mortar 1:4 (1 cement : 4 coarse
sand) in foundation and plinth :
6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) cum 6407.35
6.37 Brick work with modular extruded brunt fly ash clay sewer bricks
(conforming to IS : 4885) in arches in foundation and plinth in cement
mortar 1:3 ( 1 cement : 3 fine sand). cum 11309.95
6.38 Providing and laying autoclaved aerated cement blocks masonry with
100 mm thick AAC blocks in super structure above plinth level up to
floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate
includes providing and placing in position 2 Nos 6 mm dia M.S. bars at
every third course of masonry work. cum 8227.35
6.40 Providing and laying Gypsum panel partitions 100 mm thick with water
proof Gypsum panels of size 666x500x100 mm, made of calcite
phosphor Gypsum fixed with tongue and groove, jointed with bonding
plaster as per manufacturer’s specifications in superstructure above
plinth level up to floor V level. Gypsum blocks will have a minimum
compressive strength of 9.3 kg/cm2 sqm 853.50
6.41 Extra for Gypsum panel Partitions in superstructure above floor V level
for every four floors or part thereof. sqm 129.15
6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common
burnt clay F.P.S. (non modular) bricks of class designation 7.5 including
grouting with cement mortar 1:4 (1 cement : 4 fine sand). metre 52.00

No.
6.45 Half brick masonry with non modular fly ash bricks of class designation
10, conformingio IS :12894, in super structure above plinth and upto
floor V level.
6.45.1 Cement mortar 1 : 3 (1 cement : 3 coarse sand) sqm 941.50
6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm 917.00
6.47 Providing and laying autoclaved aerated cement blocks masonry with
150mm/230mm/300 mm thick AAC blocks in super structure above
plinth level up to floor V level with RCC band at sill level and lintel level
with approved block laying polymer modified adhesive mortar all
complete as per direction of Engineer-in-Charge. (The payment of RCC
band and reinforcement shall be made for seperately). cum 6636.95

SUB HEAD : 7.0
STONE WORK
113
BASIC RATES (SH: 7.0 STONE WORK)
No.
0373 Cramp Gun metal 25x6x300 mm each 80.00
0873 Copper pins 6 mm dia 7.5 cm long each 10.00
1154 Through and bond stone 100 Nos 5000.00
1157 Stone for masonry work cum 1100.00
1160 Red sand stone block 10 cudm 79.00
1161 White sand stone block 10 cudm 205.00
SUB HEAD : 7.0 STONE WORK 114

No.
1237 Cutting marble or sand stone slab up to 50 mm thick by

mechanical device metre 10.00
2216 Carriage of Stone blocks white & red sand stone & kota stone
slab tonne 92.24
7439 8mm thick (mirror polished tiles machine cut edge) Raj Nagar
white sqm 500.00
8683 Red sand stone gang saw cut 30 mm thick sqm 425.00
8698 Stainless steel cramps(weight 260 grams) with nuts, bolts and
washer for dry stone cladding each 100.00

7.0 STONE WORK

No.
RANDOM RUBBLE MASONRY
7.1 Random rubble masonry with hard stone in foundation and plinth including
levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12
graded stone aggregate 20 mm nominal size) upto plinth level with :
7.2 Random rubble masonry with hard stone in superstructure above plinth
level and upto floor five level, including leveling up with cement concrete
nominal size) at window sills, ceiling level and the like.
7.4 Extra for random rubble masonry with hard stone in :
7.4.1 Square or rectangular pillars cum 728.50
7.4.2 Circular pillars cum 2025.50
7.5 Extra for random rubble masonry with hard stone curved on plan for a
mean radius not exceeding 6 m. cum 804.45
COURSED RUBBLE MASONRY
7.6 Coursed rubble masonry (first sort) with hard stone in foundation and
plinth with :
7.7 Coursed rubble masonry (second sort) with hard stone in foundation &
plinth with :
7.8 Coursed rubble masonry with hard stone (first or second sort) in
superstructure above plinth level and upto floor five level.
7.8.1 Masonry work (first sort), in cement mortar 1:6 (1 cement :
6 coarse sand) cum 8718.00
7.8.2 Masonry work (second sort), in cement mortar 1:6 (1 cement:
6 coarse sand) cum 8211.10
7.10 Extra for coursed rubble masonry with hard stone (first or second sort) in:
7.10.2 Circular pillars cum 2301.65
7.11 Extra for coursed rubble masonry with hard stone (first or second sort)
curved on plan for a mean radius not exceeding 6 m. cum 875.35
ASHLAR MASONRY
7.12 Stone work in plain ashlar in super structure upto floor five level in cement
mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement
mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment
matching the stone shade :
7.12.1 One face dressed
7.12.1.1 Red sand stone cum 47132.00
7.12.1.2 White sand stone cum 69604.00
No.
7.12.2 Both face dressed

7.13 Stone work plain ashlar in arches in super structure upto floor V level in
cement mortar 1:3 (1 cement : 3 coarse sand) including centering,
shuttering and pointing with white cement mortar 1:2 (1 white cement :
2 stone dust) with an admixture of pigment matching the stone shade.
7.14 Stone work plain ashlar in domes , in super structure upto floor V level in
cement mortar 1:3 (1 cement : 3 coarse sand) including centering,
shuttering and pointing with white cement mortar 1:2 (1 white cement :
2 stone dust) with an admixture of pigment matching the stone shade.
7.15 Stone work ashlar punched (ordinary) in superstructure upto floor five
level in cement mortar 1:6 (1 white cement : 6 coarse sand) including
pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade.
7.15.2 Both faced punched
7.16 Extra for stone work, random rubble / coursed rubble masonry / ashlar
masonry above floor V level for every four floors or part thereof. cum 1493.00
7.17 Extra for plain ashlar or ashlar punched in :
7.18 Extra for stone work; plain ashlar or ashlar punched curved on plan with
a mean radius not exceeding 6 m. cum 1670.00
7.19 Extra for additional cost of centering for arches exceeding 6m span
including all strutting, bolting, wedging etc. and removal (area of soffit
to be measured). sqm 560.65

No.
SUNK, MOULDED, CARVED ASHLAR MASONRY

7.20 Stone work ashlar sunk or moulded or sunk and moulded upto floor five
level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing
with white cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade :
7.20.1 Red sand stone cum 67731.00
7.20.2 White sand stone cum 90203.00
7.21 Extra for stone work ashlar sunk or moulded or sunk and moulded or
carved in :
7.21.1 Triangular or Square or rectangular pillars cum 3131.00
7.21.2 Circular or polygonal pillars cum 8871.00
7.22 Extra for stone work ashlar sunk or moulded in cornices. per metre
per cm
girth
(60cm deep) 225.35
MISCELLANEOUS STONE WORK
7.24 Extra for stone work (veneer work) curved on plan with a mean radius
not exceeding 6 m. cum 2400.00
7.26 Providing and fixing stone dowels 10x5x2.50 cm cut to double wedge
shape as per design in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases. each 45.75
7.28 Providing and fixing sloping chajja of stone 40 mm thick and upto 80 cm
wide beyond the wall as measured along the slope in cement mortar
1:4 (1 cement : 4 coarse sand) with 12 mm diameter anchoring steel
bar, 45 cm long, fixed in each stone and supported on and including
with bricks cove in cement mortar 1:4 (1 cement : 4 coarse sand),
including pointing in cement mortar 1:2 (1 white cement : 2 stone dust)
with an admixture of pigment matching the stone shade :
7.28.1 Red sand stone :
7.28.1.1 With common burnt clay F.P.S.(non modular)
bricks of class designation 7.5 sqm 2081.20
7.28.2 White sand stone :
7.28.2.1 With common burnt clay F.P.S.(non modular)
bricks of class designation 7.5 sqm 2081.20
7.29 Providing and fixing horizontal chajja of stone 40 mm thick and upto 80
cm projection in cement mortar 1:4 (1 cement : 4 coarse sand), including
pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with
an admixture of pigment matching the stone shade :
7.29.1 Red sand stone sqm 1306.75
7.29.2 White sand stone sqm 1306.75

No.
7.30 30 mm red sand stone sun-shade (chisel-dressed) supported on red

sand stone brackets, fixed in walls with cement mortar 1:4 (1 cement :
4 coarse sand), including finishing complete. sqm 1556.40
7.31 Providing and fixing red sand stone brackets 55x22.5x45 cm sunk and
moulded including providing and fixing with 4 Nos gun metal cramp
25x6 mm 30 cm long each 5032.85
7.32 Stone work, plain in copings, cornices, string courses and plinth courses,
upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand),
including pointing with white cement mortar 1:2 (1 white cement : 2
stone dust) with an admixture of pigment matching the stone shade.
7.32.1 Red sand stone cum 66408.90
7.32.2 White sand stone cum 88880.00
7.33 Providing and fixing stone jali 40 mm thick throughout in cement mortar
1:3 (1 cement : 3 coarse sand), including pointing in white cement
mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment,
matching the stone shade, jali slab without any chamfers etc.
7.34 Extra for laying stone work in or under water and/or liquid mud including cum
cost of pumping or bailing out water and removing slush etc. complete. per metre
depth 794.65
NOTE :- The quantity will be calculated by multiplying the depth
measured from sub-soil water level up to the centre of gravity of stone
work under sub - water with the quantity of stone work in cum executed
under the sub-soil water. The depth of centre of gravity shall be reckoned
correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than
0.05 m ignored.
7.35 Extra for laying stone work in or under foul position. cum 336.55
7.38 Stone tile work for wall lining upto 10 m height with special adhesive
over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand),
including pointing in white cement with an admixture of pigment to match
the stone shade.
7.38.1 8mm thick (mirror polished and machine cut edge)
7.38.1.1 Granite stone of any colour and shade sqm 2537.40
7.38.1.2 Raj Nagar plain white marble/ Udaipur green
marble/ Zebra black marble sqm 2263.10

SUB HEAD : 8.0
CLADDING WORK
120
BASIC RATES (SH: 8.0 CLADDING WORK)
No.

0019 Hand Grinder for mirror polish day 250.00
0128 Mate day 617.00
1239 18 mm thick Flamed finish granite stone slab sqm 1000.00
1240 18 mm thick Italian Marble stone slab, Perlato
(slab area up to 0.5 sqm). sqm 3209.00
2216 Carriage of Stone blocks white & red sand stone & kota
stone slab tonne 92.24
4009 M.S. Tube Hot finished welded type Kg 57.00
7244 Table rubbed polished stone 18 mm thick (75x50cm) Agaria
Marble stone - 18 mm thick sqm 1620.00
7245 Table rubbed polished stone 18mm thick (75x50cm) Granite
stone-18 mm thick sqm 1620.00
7297 Granite of any colour, 18 mm thick (slab area above 0.50 sqm) sqm 1800.00
7338 Gun metal cramp kg 315.00
SUB HEAD : 8.0 CLADDING WORK 121

No.
7452 Raj nagar plain white marble (table rubbed and polished) 18 mm
thick (slab area upto 0.50 sqm) sqm 575.00
7453 Raj nagar plain white marble (table rubbed and polished) 18 mm
thick (slab area more than 0.50 sqm) sqm 690.00

8.0 CLADDING WORK

No.
8.1 Marble work gang saw cut (polished and machine cut) of thickness 18
mm for wall lining (veneer work), backing filled with a grout of average 12
mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including
pointing with white cement mortar 1:2 (1 white cement : 2 marble dust)
with an admixture of pigment to match the marble shade (To be secured
to the backing by means of cramps, which shall be paid for separately)
8.1.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble.
8.1.1.1 Area of slab upto 0.50 sqm sqm 4439.40
8.1.1.2 Area of slab over 0.50 sqm sqm 4615.65
8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished,
premoulded and prepolished, machine cut for kitchen platforms, vanity
counters, window sills, facias and similar locations of required size,
approved shade, colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high gloss finish etc. complete
at all levels.
8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble
8.2.2 Granite of any colour and shade
8.3 Providing edge moulding to 18 mm thick marble stone counters, Vanities
etc., including machine polishing to edge to give high gloss finish etc.
complete as per design approved by Engineer-in-Charge.
8.3.1 Marble work metre 220.35
8.3.2 Granite work metre 376.25
8.4 Extra for fixing marble /granite stone, over and above corresponding
basic item, in facia and drops of width upto 150 mm with epoxy resin
based adhesive, including cleaning etc. complete. metre 434.25
8.5 Extra for providing opening of required size & shape for wash basin/
kitchen sink in kitchen platform, vanity counter and similar location in
marble/ Granite/ stone work, including necessary holes for pillar taps
etc. including moulding, rubbing and polishing of cut edges etc. complete. each 734.55
8.6 Mirror polishing on marble work/Granite work/stone work where ever
required to give high gloss finish complete. sqm 368.00
8.7 Providing and fixing cramps of required size & shape in RCC/ CC / Brick
masonry backing with cement mortar 1:2 ( 1 cement :2 coarse sand),

No.
including drilling necessary hole in stones and embedding the cramp in

the hole (fastener to be paid separately).
8.7.1 Gunmetal cramps kg 627.85
8.7.2 Stainless steel cramps kg 612.60
8.8 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick
masonry surface backing including drilling necessary holes and the
cost of bolt etc complete.
8.8.1 Wedge expansion type
8.8.1.1 Fastener with threaded dia 6 mm each 33.05
8.9 Stone tile (polished) work for wall lining over 12 mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm
including pointing in white cement complete.
8.9.1 8mm thick
8.9.1.1 Raj nagar plain white marble/ Udaipur green

marble/ Zebra black marble sqm 2515.40
8.9.1.2 Granite of any colour and shade sqm 2926.85
8.10 Providing and fixing stone slab with table rubbed, edges rounded and
polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal
partitions by cutting a chase of appropriate width with chase cutter and
embedding the stone in the chase with epoxy grout or with cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6
mm nominal size) as per direction of Engineer-in-charge and finished
smooth.
8.10.1 White Agaria Marble Stone sqm 3216.90
8.10.2 Granite Stone of approved shade sqm 3216.90
8.11 Providing and fixing machine cut, mirror/ eggshell polished , Marble
stone work for wall lining (veneer work) including dado, skirting, risers of
steps etc., in required design and pattern wherever required, stones of
different finished surface texture, on 12 mm (average) thick cement
mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement
slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed
with pigment of matching shade, including rubbing, curing, polishing
etc. all complete as per Architectural drawings, and as directed by the
Engineer-in-Charge.
8.11.1 18 mm thick Italian Marble stone slab,Perlato, Rosso verona,
Fire Red or Dark Emperadore etc. sqm 8823.75

No.
8.14 Stone work (machine cut edges) for wall lining etc. (veneer work) upto
10 metre height, backing filled with a grout of average 12 mm thick
cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in
white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture
of pigment matching the stone shade : (To be secured to the backing
and the sides by means of cramps and pins which shall be paid for
separately) :
8.14.1 Red sand stone - exposed face fine dressed with rough
backing.
8.14.1.1 70 mm thick sqm 4460.95
8.14.1.2 60 mm thick sqm 4316.20
8.14.1.3 50 mm thick sqm 4171.80
8.14.1.4 40 mm thick sqm 4026.80
8.14.1.5 30 mm thick sqm 3882.00
8.14.2 Red sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.2.1 70 mm thick sqm 6154.70
8.14.2.2 60 mm thick sqm 6010.00
8.14.2.3 50 mm thick sqm 5865.60
8.14.2.4 40 mm thick sqm 5720.60
8.14.2.5 30 mm thick sqm 5575.75
8.14.3 White sand stone - exposed face fine dressed with
rough backing .
8.14.3.1 70 mm thick sqm 6034.30
8.14.3.2 60 mm thick sqm 5664.85
8.14.3.3 50 mm thick sqm 5296.25
8.14.3.4 40 mm thick sqm 4925.00
8.14.3.5 30 mm thick sqm 4556.15
8.14.4 White sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.4.1 70 mm thick sqm 7728.10
8.14.4.2 60 mm thick sqm 7358.65
8.14.4.3 50 mm thick sqm 6990.05
8.14.4.4 40 mm thick sqm 6618.80
8.14.4.5 30 mm thick sqm 6249.90
8.14.5 Gang saw cut stone
8.14.5.1 30mm thick White sand stone sqm 2549.75
8.14.5.2 30mm thick Red sand stone sqm 2360.10

No.
8.15 Providing and fixing stainless steel cramps of required size and shape
for anchoring stone wall lining to the backing or securing adjacent stones
in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases in stone and holes in walls
wherever required. kg 612.60
8.16 Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing
adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2
coarse sand), including making the necessary chases. each 36.20
8.17 Wall lining butch work upto 10m height with Dholpur stone 40 mm thick
rough facing on the exposed surface with stone strips of minimum length
300 mm and required width, including embedding every tenth layer and
bottom most layer in masonry or concrete after making necessary chases
of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12
mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled
pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment to match the shade of stone complete as per
direction of Engineer-in-charge. sqm 2388.00
8.18 Stone work (machine cut edges Veneer work) for wall lining upto 10 m
height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1
Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement
: 2 stone dust), including rubbing and polishing complete. (To be secured
to the backing and the sides by means of cramps and pins which shall
be paid for separately).
8.18.1 Kota stone slabs exposed face dressed and rubbed.
8.18.1.1 25 mm thick sqm 2890.25
8.19 Extra for stone work for wall lining on exterior walls of height more than
10 m from ground level for every additional height of 3 m or part there of. sqm 129.65
STONE WORK DRY CLADDING
8.20 Providing and fixing dry cladding upto 10 metre heights with 30mm thick
gang saw cut stone with (machine cut edges) of uniform colour and
size upto 1mx1m, fixed to structural steel frame work and/ or with the
help of cramps, pins etc. and sealing the joints with approved weather
sealant as per Architectural drawing and direction of Engineer-in-charge.
(The steel frame work, stainless steel cramps and pins etc. shall be
paid for separately).
8.20.1 Red sand stone - 30mm thick gang saw cut stone sqm 2217.75
8.20.2 White sand stone - 30mm thick gang saw cut stone sqm 2407.40
8.21 Providing and fixing structural steel frame (for dry cladding with 30 mm
thick gang saw cut with machine cut edges sand stone) on walls at all
heights using M.S. square/ rectangular tube in the required pattern as
per architectural drawing, including cost of cutting, bending, welding
etc. The frame work shall be fixed to the wall with the help of M.S.
brackets/ lugs of angle iron/ flats etc. which shall be welded to the
frame and embedded in brick wall with cement concrete block 1:2:4 (1
cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)
of size 300x230x300 mm, including cost of necessary centring and

No.
shuttering and with approved expansion hold fasteners on CC/RCC

surface, including drilling necessary holes. Approved cramps/ pins etc.
shall be welded to the frame work to support stone cladding, the steel
work will be given a priming coat of Zinc primer as approved by Engineer-
in-charge and painted with two or more coats of epoxy paint (Shop
drawings shall be submitted by the contractor to the Engineer-in-charge
for approval before execution). The frame work shall be fixed in true
horizontal & vertical lines/planes. (Only structural steel frame work shall
be measured for the purpose of payment, stainless steel cramps shall
be paid for separately and nothing extra shall be paid). kg 183.35
8.22 Providing and fixing adjustable stainless steel cramps of approved quality,
required shape and size, adjustable with stainless steel nuts, bolts and
washer (total weight not less than 260 gms), for dry stone cladding
fixed on frame work at suitable location, including making necessary
recesses in stone slab, drilling required holes etc complete as per
direction of the Engineer-in-charge. each 327.00
NOTE: Item no 8.14, 8.15, 8.16, 8.17, 8.18, 8.19, 8.20, 8.21 & 8.22
are brought from Sub Head 7 i.e. Stone Work, Item no 7.23, 7.25,
7.27, 7.36, 7.37, 7.39, 7.40, 7.41 & 7.42
8.23 Providing 50x50x50 mm 2nd class teak wood plugs including cutting
brick work and fixing in cement mortar 1:3 (1 cement : 3 fine sand) and
making good the walls etc. each 33.90
8.24 Providing and fixing expandable fasteners of specified size with necessary
plastic sleeves and galvanised M.S. screws including drilling holes in
masonry work /CC/ R.C.C. and making good etc. complete.
8.24.1 25 mm long each 18.95
8.24.2 32 mm long each 20.35
8.24.3 40 mm long each 24.35
8.24.4 50 mm long each 25.70
8.25 Providing and fixing 2nd class teak wood plain lining tongued and grooved,
including wooden plugs complete with necessary screws and priming
coat on unexposed surface.
8.25.1 40 mm thick sqm 6137.70
8.25.2 25 mm thick sqm 4057.75
8.25.3 20 mm thick sqm 3291.15
8.25.4 12 mm thick sqm 2181.80
8.26 Providing and fixing in wall lining flat pressed three layer (medium density)
particle board or graded wood Pre-laminated one side decorative
lamination and other side balancing lamination Grade I, Type II, IS :
12823 marked, including priming coat on unexposed arrangement and
screws etc. complete :
8.26.1 12 mm thick sqm 1269.60
8.26.2 18 mm thick sqm 1431.50
8.26.3 25 mm thick sqm 1799.45
No.
8.27 Providing and fixing specified wood frame work consisting of battens
50x25mm fixed with rawl plug and drilling necessary holes for rawl plug
etc. including priming coat complete.
8.27.1 Kiln seasoned and chemically treated hollock wood cum 165255.05
8.28 Providing and fixing plywood 4 mm thick, one side decorative veneer
conforming to IS: 1328 (type-1), for plain lining / cladding with necessary
screws, including priming coat on unexposed surface with :
8.28.1 Decorative veneer facings of approved manufacture sqm 1551.00
8.29 Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842,
plain lining with necessary screws, priming coat on unexposed surface
etc., complete. sqm 1502.85
8.30 Providing and fixing skirting with Pre-laminated (one side decorative and
other side balancing lamination) flat pressed 3 layer or graded particle
board (medium density) Grade I, Type II, IS :12823 marked, with necessary
fixing arrangements and screws, including drilling necessary holes for
rawl plugs etc. and priming coat on unexposed surface complete :
8.30.1 18 mm thick sqm 1891.50
8.30.2 25 mm thick sqm 2259.40
NOTE: Item No 8.23, 8.24, 8.25, 8.26, 8.27, 8.28, 8.29 & 8.30 are
brought from Sub Head 9 i.e. Wood & PVC Work, Item No. 9.32,
9.33, 9.34, 9.35, 9.36, 9.37, 9.38 & 9.39
8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to
IS: 15622 (thickness to be specified by the manufacturer), of approved
make, in all colours, shades except burgundy, bottle green, black of
any size as approved by Engineer-in-Charge, in skirting, risers of steps
and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3
coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,
including pointing in white cement mixed with pigment of matching shade
NOTE: Item no 8.31 is brought from Sub Head 11 i.e. Flooring,
Item No 11.36
8.32 Designing, fabricating, testing, installing and fixing in position Curtain
Wall with Aluminium Composite Panel Cladding, with open grooves for
linear as well as curvilinear portions of the building , for all heights and
all levels etc. including:
(a) Structural analysis & design and preparation of shop drawings for
pressure equalisation or rain screen principle as required, proper drainage
of water to make it watertight including checking of all the structural
and functional design.
(b) Providing, fabricating and supplying and fixing panels of aluminium
composite panel cladding in pan shape in metalic colour of approved
shades made out of 4mm thick aluminium composite panel material
consisting of 3mm thick FR grade mineral core sandwiched between
two Aluminium sheets (each 0.5mm thick). The aluminium composite
panel cladding sheet shall be coil coated, with Kynar 500 based PVDF
/ Lumiflon based fluoropolymer resin coating of approved colour and

No.
shade on face # 1 and polymer (Service) coating on face # 2 as specified

using stainless steel screws, nuts, bolts, washers, cleats, weather
silicone sealant, backer rods etc.
(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip
Galvanised with serrations and serrated washers to arrest the wind load
movement, fasteners, SS 316 Pins and anchor bolts of approved make
in SS 316, Nylon separators to prevent bi-metallic contacts all complete
required to perform as per specification and drawing The item includes
cost of all material & labour component, the cost of all mock ups at
site, cost of all samples of the individual components for testing in an
approved laboratory, field tests on the assembled working curtain wall
with aluminium composite panel cladding, cleaning and protection of
the curtain wall with aluminium composite panel cladding till the handing
over of the building for occupation. Base frame work for ACP cladding is
payable under the relevant aluminium item.s The Contractor shall provide
curtain wall with aluminium composite panel cladding, having all the
performance characteristics all complete , as per the Architectural
drawings, as per item description, as specified, as per the approved
shop drawings and as directed by the Engineer-in-Charge. However, for
the purpose of payment, only the actual area on the external face of the
curtain wall with Aluminum Composite Panel Cladding (including width
of groove) shall be measured in sqm. up to two decimal places. sqm 4309.80
NOTE: Item No. 8.32 is brought from Sub Head 25 i.e. Structural
Glazing Aluminium Composite Panel, Item No. 25.7

SUB HEAD : 9.0
WOOD AND P.V.C. WORK
130
BASIC RATES (SH: 9.0 WOOD AND P.V.C. WORK)
No.
0162 Labour for fabrication of uPVC extruded casement/ sliding windows
and doors including drilling holes, fixing of fittings & hardwares, hire
charges of drill machine and electricity charges etc. sqm 485.00
0163 Labour for installation of uPVC extruded casement/ sliding windows
and doors including scaffolding sqm 430.00
0237 Multi purpose fibre (high impact poly propelene reinforced) cement
board 8 mm thick sqm 220.00
0305 Bamboo 25 mm dia 2.5 metre long score 400.00
0341 Flat pressed 3 layer particle board (medium density) Grade 1,
0346 Extra for veneered particle board with Teak veneering on one side
and commercial veneering on other side sqm 230.00
0347 Extra for veneered particle board with Commercial veneering on
both sides sqm 155.00
0348 Extra for veneered particle board with Teak veneering on both sides sqm 500.00
0384 Brass butt hinges (heavy type) :75x65x4.0 mm (weighing not
less than 0.20 kg) 10 Nos 838.00
SUB HEAD : 9.0 WOOD AND P.V.C. WORK 131

No.

0388 Brass parliamentary hinges 75x100x20x3.2 mm 10 Nos 1870.00
0411 Brass door latch 300x16x5 mmweighing not less than 0.380 kg each 185.00
0412 Brass door latch 250x16x5 mm weighing not less than 0.350 kg each 175.00
0413 Brass mortice latch and lock 100x65 mm with 6 levers and a pair
of brass lever handles each 400.00
0414 Brass mortice latch 100x65mm with a pair of brass lever handles each 310.00
0424 Brass casement stays (straight peg type) 300 mm weighing not
less than 0.33 kg each 126.00
0438 Brass night latch each 610.00
0447 Brass cupboard knob or wardrobe knob 50 mm each 36.00
0552 75 mm SS fancy handle for Kitchen Cabinet 10 Nos 255.00
0555 Chromium plated Brass handles 125 mm with plate 175 x32 mm each 160.00
0556 Chromium plated Brass handles 100 mm with plate 150 x 32 mm each 140.00
0557 Chromium plated Brass handles 75mm with plate 125x32 mm each 125.00
0558 Chromium plated Brass mortice latch and lock 100x65 mm with
6 levers and a pair of brass lever handles each 470.00
0568 Chromium plated brass casement window fastener each 90.00

No.
0569 Chromium plated Brass casement stays (straight peg type)
300 mm weighing not less than 0.33 kg each 140.00
0583 Chromium plated Brass Night latch each 500.00
0584 Chromium plated Brass Wardrobe Knob 50 mm each 80.00
125x65x 2.12 mm 10 Nos 135.00
100x58x 1.90 mm 10 Nos 80.00
75x47x 1.70 mm 10 Nos 56.00
50x37x 1.50 mm 10 Nos 49.00
0641 Bright finished or black enameled mild steel bolts and nuts
50x6 mm each 5.00

No.

0656 Nickel plated mild steel piano hinges 1 mm thick 35 mm wide metre 44.00

No.
0705 Anodised Aluminium handles 75mm with plate 125 x 32 mm 10 Nos 231.00
0706 Anodised Aluminium kicking plate 50 cm long 100x3.15 mm each 142.00
0713 Block board construction flush door with teak wood ply on both
faces 35 mm thick sqm 1800.00
0717 Block board construction flush door with commercial ply on both
0752 Block board construction flush door lipping 25 mm thick sqm of
door area 300.00
0753 Square vision panel in Block board construction flush door not sqm of
exceeding 0.10 sqm door area 130.00
0754 Circular vision panel in Block board construction flush door sqm of
door area 135.00
0755 Decorative type louvers in Block board construction flush door sqm of
door area 265.00
0757 Rebate cutting in block board construction flush door sqm of
door area 70.00
0759 Decorative plywood 4 mm sqm 320.00
0763 Glue kg 75.00
0834 Synthetic enamel paint in all shades except black or chocolate
shade litre 160.00

No.

head with slots 10 Nos 38.00
1200 Kiln seasoned selected sheesham wood planks 10 cudm 650.00
1238 Extra for selected planks of first class teakwood 10 cudm 150.00
2412 Ply wood 5 ply with commercial ply on both faces 6 mm thick sqm 300.00
2413 12 mm commercial ply sqm 500.00
2414 18 mm thick block board with commercial ply veneering on
both side sqm 760.00
2449 Oxidised mild steel pull bolt lock (locking bolt) of size 85 mm x
2455 Brass hanging type door stopper 150 mm each 75.00
2456 Hydraulic door closer bottle type M.S. body with necessary
accessories and screws complete each 673.00
2459 Anodised Aluminium hanging type door stopper each 19.00
2464 Anodised Aluminium pull bolt lock (locking bolt) of size 85 mm x
2465 Anodised Aluminium Casement stay 250 mm each 32.00
2480 Ply wood 5 ply with teak ply on both faces 9 mm thick sqm 850.00

No.
2481 Ply wood 5 ply with teak ply on one face and commercial ply
on another face 9 mm thick sqm 870.00
2483 Ply wood 7 ply with teak ply on one face and commercial ply
on another face 9 mm thick sqm 950.00
2486 Pre-laminated with decorative lamination one side and other
side balancing lamination exterior Grade-I MDF Board 25 mm
thick confirming to IS: 14587 sqm 860.00
thick confirming to IS:14587 sqm 430.00
thick confirming to IS:14587 sqm 565.00
2489 PVC edge bending tape 2.00 mm thick metre 20.00
2504 Kiln seasoning of timber cum 750.00
2505 Hollock wood in planks 10 cudm 390.00
2640 Glass panes of required thickness having 120 minutes of fire
resistance both intensity and radiation control (EW 120) and
minimum 20 minutes of insulation (EI 20) sqm 25000.00
2641 G.I U beading of 1.6 mm thick G.I sheet with ceramic tape. metre 245.00
2642 Ceramic tape 5 x20 mm size metre 410.00
3991 Galvanized iron (1.6 ± 0.2 mm) thick reinforcement for small series
casement window/door frame, sash, mullion & small series sliding
window frame metre 66.00
casement window/door frame, sash, mullion, big & small series
sliding window frame metre 71.00
casement door sash metre 97.00
sliding window / door sash metre 86.00
3995 G.I fasteners 100 x 8 mm each 14.00
7001 Brass 100mm mortice latch and lock with 6 levers without pair
of handles each 210.00
7003 Pair of Anodised Aluminium lever handles for 100 mm mortice latch
and lock each 215.00
7009 12.5 mm thick tapered edge plain Gypsum plaster board confirming
to IS 2095 (Part- I) : 2011 sqm 155.00

No.

7023 Chromium plated brackets (curtain rods) each 7.00
7029 Galvanised wire mesh of average width of aperture 1.4 mm and
nominal dia of wire 0.63 mm sqm 250.00
7032 Frosted glass sheet of nominal thickness 4 mm (weighing not
less than 10 kg/sqm) sqm 460.00
7035 Nickel plated M.S. Brackets for curtain rod 20 mm each 7.00
7036 Nickel plated M.S - Brackets for curtain rod 25 mm each 8.00
7049 Teak wood lipping of size 25x3 mm in pelmets metre 14.00
7055 Flat pressed 3 layer and graded particle board (medium density)
Grade 1 conforming to IS : 3087 - 18 mm thick sqm 480.00
7056 Aluminium tee channel (heavy duty) with rollers and stop end metre 100.00
7059 Aluminium hanging floor door stopper with twin rubber & stopper each 40.00
7060 Hydraulic door closer tubular type Aluminium section body each 560.00
7063 Oxidised M.S.casement stay (straight peg type) 300 mm not less
7064 Oxidised M.S.casement stay (straight peg type) 250 mm not less
7065 Oxidised M.S. casement stay (straight peg type) 200 mm not less
styles & rails as per TADS 15:1995 and panels of 12 mm thick
plain type-I, medium density flat pressed three layer, graded par-
ticle board (FPT-I) as per IS:3087 bonded with BWP type synthetic
resin adhesive, as per IS:848 sqm 1620.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick
both sides prelaminated type-I, medium density flat pressed three
layer, graded particle board (FPT-I) as per IS:3087 bonded with
BWP type synthetic resin adhesive, as per IS:848 sqm 1720.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick one
side prelaminated type-I, and other side balancing lamination, me-
dium density flat pressed three layer, graded particle board (FPT-I)
as per IS:3087 bonded with BWP type synthetic resin adhesive,
as per IS:848 sqm 1910.00

No.
styles & rails as per TADS 15:1995 and panels of sheet glass
using 10 kg/ sqm glass panes sqm 1620.00
gauge with average width of aperture 1.4 mm in both directions
with wire of dia 0.63 mm sqm 1620.00
gauge with average width of aperture 1.4 mm in both directions
with wire of dia 0.63 mm sqm 1430.00
7157 Laminated veneer lumber confirming to TADS 15:1995 manufac
tured in factory in frames of doors, windows 10 cudm 700.00
7184 Oxidised M.S. safety chain (weighing not less than 450 gms)
for door each 57.00
7269 25 mm thick particle board sqm 460.00
7271 Second class teak wood lipping 25 mm wide x 12 mm thick metre 29.00
7272 25 mm thick melamine faced prelaminated three layer particle
board sqm 900.00
7307 For flush door shutters Extra for providing teak veneering on
one side instead of commercial veneering sqm 330.00
7315 Expandable fastener with plastic sleeve and M.S. screws.
7349 12 mm M.S. 'U' beading metre 14.00
7366 Glass reinforced Gypsum (GRG) plaster board 12.5 mm thick
confirming to IS 2095 (Part- 3) : 1996 sqm 240.00
7367 Galvanised M.S. sheet 0.5 mm thick pressed channel section
of size 50x32 mm metre 57.00
7369 Galvanised M.S. sheet 0.50 mm thick pressed stud : 48x34x36 mm metre 71.00
7443 Aluminium single cleat of size 30x32x3 mm each 14.00
7444 Aluminium grip strip of size 50x12x2 mm each 11.00
7445 25 mm thick prelaminated flush door shutter both side decorative sqm 800.00
7449 Aluminium U beading kg 210.00
7451 Glass sheet (Pin headed) 4 mm thick sqm 305.00

No.
7468 Veneered particle board with commercial veneering on both sides
7477 Prelaminated particle board with one side decorative and other
side balancing lamination, flat pressed 3 layer & graded (medium
density) Grade i, Type II conforming to IS : 12823 (exterior grade)
density) Grade I, Type II conforming to IS : 12823 (exterior grade)
density) Grade I, Type II conforming to IS : 12823 (exterior grade)
7485 Oxidised M. S. hinges finished with nickel plating 50 mm
(Over all width) metre 40.00
7486 Oxidised M. S. hinges finished with nickel plating 65 mm
(Over all width) metre 52.00
7518 PTMT door catcher 72x42 mm each 24.00
8003 Factory made PVC rigid foam panelled shutter i/c carriage sqm 1547.45
8004 Factory made PVC rigid foam panelled shutter as per IS : 4020
i/c carriage sqm 1547.45
8010 48mmX40mmX1.5mm thick Factory made door frame of PVC
8011 Factory made door frame PVC extruded sheet i/c carriage metre 251.58

No.
8014 Factory made door frame of size 50x47 mm with wall thickness
5 mm made of single piece extruded profile metre 298.74
8017 Fire rated door frame made with 1.6 mm thick G.I sheet
(120 minutes fire rating) metre 1000.00
8018 Fire rated door shutter made with 1.6 mm thick G.I sheet (120
minutes fire rating) including hinges ( without glass panels) sqm 5000.00
8100 Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm 10 Nos 123.00
8101 SS ball bearing of size 100 x89x3mm each 450.00
8116 Zinc alloy (white powder coated) 3D Hinges for uPVC door each 451.00
8117 Zinc alloy (white powder coated) handles with zinc plated mild
steel multi point locking having transmission gear, cylinder with
keeps and one side key for uPVC casement door each set 2296.00
8118 Zinc alloy (white powder coated) handles along with zinc plated
mild steel multi point locking having transmission gear with keeps
for uPVC sliding window each set 1394.00
8119 Zinc alloy (white powder coated) handles with key along with zinc
plated mild steel multi point locking having transmission gear with
keeps for uPVC sliding door each set 1150.00
8121 uPVC extruded (small series) casement window frame size
8122 uPVC extruded (small series) casement window sash/window
mullion size 47x68 mm metre 282.90
8125 uPVC extruded glazing bead of appropriate dimension for small
series casement window Sash metre 98.40
8126 uPVC extruded (big series) casement window frame size 67x60 mm metre 319.80
8127 uPVC extruded (big series) casement door frame size 67x64 mm metre 360.80
8128 uPVC extruded (big series) casement window sash/window
mullion/door mullion size 67x80 mm metre 426.40
8129 uPVC extruded (big series) casement door sash size 67x110 mm metre 516.60
8130 uPVC extruded glazing bead of appropriate dimension for big
series casement window/door sash metre 123.00
8131 uPVC extruded glazing bead of appropriate dimension for small
series sliding window sash metre 60.00
8132 uPVC extruded glazing bead of appropriate dimension for big
series of sliding window/ door sash metre 85.00
8133 uPVC extruded (small series) 2 track sliding window frame
size 52x44 mm metre 285.00
8134 uPVC extruded (big series) 2 track sliding window/door frame
size 67x50mm metre 385.00
8135 uPVC extruded (small series) 3 track sliding window frame size
92x44 mm metre 380.00

No.
8136 uPVC extruded (big series) 3 track sliding window/door frame

size 116x45mm metre 530.00
8137 uPVC extruded (small series) 2 track sliding window sash/3
track sliding window sash size 32x60mm metre 265.00
8138 uPVC extruded (big series) 2 track sliding window sash size
8139 uPVC extruded (big series) 3 track sliding window sash size
8140 uPVC extruded interlock of appropriate dimension for small
series sliding window sash metre 80.00
8141 uPVC extruded interlock of appropriate dimension for big
series sliding window/ door sash metre 90.00
8142 uPVC extruded inline adaptor of appropriate dimension for big
series sliding window/door sash metre 90.00
8143 uPVC extruded 2 track sliding door sash/ 3 track sliding door
sash (big series) size 46x82mm metre 350.00
8219 Stainless steel butt hinges (heavy weight) 125x64x2.5 mm
IS :12817 marked 10 Nos 350.00
IS :12817 marked 10 Nos 255.00
IS :12817 marked 10 Nos 205.00
8222 M.S. heavy weight butt hinges 125x90x4.0 mm IS: 1341 marked. 10 Nos 210.00
8225 M.S. heavy weight butt hinges 50x40x2.5 mm IS : 1341 marked 10 Nos 80.00
8647 Stainless steel screws 30 x 4 mm 100 Nos 32.00
8700 10 mm thick calcium silicate board sqm 420.00
8703 Telescopic drawer channels 300 mm long set 230.00
8704 Stainless steel roller for sliding arrangement in racks/ cupboards/
cabinets shutter each 9.00

No.
8705 50 mmX42 mmX2 mm thick Factory made door frame of PVC

8706 25 mm thick factory made PVC flush door shutter i/c carriage sqm 1700.00
8707 Factory made glass reinforced plastic door frame 90x45 mm i/c
carriage metre 467.00
8708 30 mm thick factory made glass fiber reinforced plastic panel door
8709 30 mm thick factory made solid PVC profile panelled door single
piece extruded profile decorative finish (wood grain printed on
both side) sqm 2100.00
8710 Factory made solid PVC door frame 60 x 30 mm i/c carriage metre 315.00
8711 20 mm factory made solid PVC panel door shutter i/c carriage sqm 2050.00
8712 30 mm thick factory made solid PVC profile panelled door single
piece extruded profile non decorative finish sqm 2000.00
8713 Fiber glass reinforced plastic chajja sqm 3000.00
8714 Magnetic catcher triple strip vertical type each 24.00
8715 Magnetic catcher double strip horizontal type each 18.00
8716 100 mm mortice lock with 6 levers for aluminium door each 375.00
8719 2nd class teak wood moulded beading or Taj beading/ornamental
bleading of size 18X5 mm metre 28.00
8720 Ceiling sections 0.55 mm thick having a knurled web of 51.55 mm
and two flanges of 26 mm each with lips of 10.55 mm metre 35.00
8721 Perimeter channel having one flange of 20 mm and another flange
of 30 mm with thickness of 0.55 mm and web of length 27 mm metre 22.00
8722 Nylon sleeves & wooden screws (40 mm) each 2.00
8723 Counter sunk ribbed head screw 25 mm 100 Nos 68.00
8724 12 mm thick marine plywood conforming to IS: 710 sqm 695.00
8725 12 mm thick fire retardant plywood conforming to IS: 5509 sqm 850.00
8730 30 mm thick factory made glass fiber reinforced plastic flush door
8734 P.V.C. Single piece extruded door frame of profile size 50 mm x
47mm with wall thickness of 5 mm metre 255.00
piece extruded profile non decorative finished (Matt finished) sqm 2150.00
piece extruded profile decorative finished (wood grain finished) sqm 2600.00
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and
0.50mm dia wire sqm 400.00

No.
8738 Factory made door frame fire rated (60 minutes) made with 16
SWG G.I. Sheet of section 143 mm x 57 mm duly filled with
vermuculite based concrete mix metre 1050.00
8739 Fire rated door shuttere made with 16 SWG G.I. sheet (60 minutes)
without panel sqm 4500.00
8740 Fire seal Putty kg 295.00
8741 Clear fire resistant glass panes 6mm thick (60 minutes) sqm 21500.00
8742 G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/ m²)
with ceramic tape of suitable thickness and fire resistant primer
coating metre 295.00
8743 Matrix Mineral Board metre 68.00
8744 Panic Bar / latch (Double point) each 5200.00
8745 65 mm x 55 mm x 2 mm thick Factory made door frame of PVC
8746 37 mm thick Factory made shutter with style,rails and panels of
PVC extruded section in white or grey finish i/c carriage sqm 2400.00
8747 75 mm x 53 mm x 2.0 mm thick Factory made door frame of PVC
8748 37 mm thick Factory made fusion welded shutter with style,
rails and panels of PVC extruded section in wooden finish sqm 2600.00
8749 Zinc alloy (white powder coated) touch lock with hook for wire
mesh shutter each 120.00
8750 Zinc alloy (white powder coated) casement handle for uPVC
window/door each 130.00
8751 Zinc alloy (white powder coated) touch lock withhook for uPVC
window/door each 105.00
8752 Zinc alloy body with single nylon roller (weight bearing capacity
to be 40 Kg) for uPVC sliding window each 56.00
8753 Stainless Steel (SS - 304) with adjustable double nylon roller
(weight bearing capacity to be 120 Kg) for uPVC sliding door/
window each 95.00
8754 Zinc alloy (white powder coated) cresent lock for uPVC sliding
door/window each 115.00
8755 Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for
uPVC windows each 205.00
8756 Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for
uPVC windows each 230.00
8757 Stainless steel friction hinges (SS-304 grade) size 300 x 19 x
1.9 mm for uPVC window each 245.00

No.
8760 Glass panes of required thickness having 60 minutes of fire resistance
both integrity and radiation control (EW 60) and minimum 20 minutes
of insulation (EI 20) sqm 22500.00
8772 Aluminium Track on bottom rail for uPVC window metre 30.00
8773 Wool pile/ weather pile strip for uPVC sliding window metre 20.00
8775 Steel Galvanised tubular reinforcement for uPVC door/ window metre 60.00
8777 GI Fastener 100x8 mm each 15.00

9.0 WOOD AND P. V. C. WORK

No.
FRAMES AND TRUSSES
9.1 Providing wood work in frames of doors, windows, clerestory windows

and other frames, wrought framed and fixed in position with hold fast
lugs or with dash fasteners of required dia & length ( hold fast lugs or
dash fastener shall be paid for separately).
9.1.1 Second class teak wood cum 130183.05
9.1.2 Sal wood cum 105327.20
9.2 Providing laminated veneer lumber conforming to IS:14616 and TAD -15:
2001 (Part B) in factory made frames of doors, windows, clerestory
windows and other frames, wrought framed and fixing in position with
hold fast lugs or with dash fasteners of required dia & length (hold fast
lugs or dash fastener shall be paid for separately). cum 113706.40
9.3 Providing wood work in frames of false ceiling, partitions etc. sawn and
fixed in position with necessary stainless steel screws etc.
9.3.1 Sal wood cum 95893.90
9.4 Extra for additional labour for circular works, such as in frames of fan
light
9.4.1 Second class teak wood cum 13018.35
9.4.2 Sal wood cum 10532.80
9.5 Providing and fixing panelled or panelled and glazed shutters for doors,
windows and clerestory windows fixing with butt hinges of required
size with necessary screws, excluding panelling which will be paid for
separately, all complete as per direction of Engineer-in-charge. (Note:-
Butt hinges and necessary screws shall be paid separately)
9.5.1 Second class teak wood

9.5.1.1 35 mm thick shutters sqm 3613.35
9.5.2 Kiln seasoned and chemically treated hollock wood
9.5.3 Kiln seasoned selected planks of sheesham wood

No.
9.6 Providing and fixing 35 mm thick factory made laminated veneer lumber
door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing
with butt hinges of required size with necessary screws, all complete
as per directions of Engineer- in-charge and panelling with panels of :
(Note:- Butt hinges and necessary screws shall be paid separately)
9.6.1 12 mm thick plain grade -1, medium density flat pressed three
layer particle board FPT - I or graded wood particle board
FPT- I, IS : 3087 marked, bonded with BWP type synthetic
resin adhesive as per IS : 848 : sqm 2636.60
9.6.2 12 mm thick pre-laminated particle board (decorative lamination
on both sides) grade -1, medium density flat pressed, three
layer particle board FPT- I or graded wood particle board FPT- I,
conforming to IS : 3087, bonded with BWP type synthetic resin
adhesive as per IS : 848 and prelaminated conforming to IS :
12823, Grade 1, Type - II marked : sqm 2770.40
9.6.3 12 mm thick one side Pre-laminated particle board (decorative
lamination on one side and other sides balancing lamination)
grade -1, medium density flat pressed, three layer particle
board FPT - I or graded wood particle board FPT-1 conforming
to IS : 3087 bonded with BWP type synthetic resin adhesive
as per IS : 848 and pre-laminated conforming to IS : 12823,
Grade -1, Type II marked : sqm 3024.60
9.7 Providing and fixing panelling or panelling and glazing in panelled or

panelled and glazed shutters for doors, windows and clerestory windows
(Area of opening for panel inserts excluding portion inside grooves or
rebates to be measured). Panelling for panelled or panelled and glazed
shutters 25 mm to 40 mm thick :
9.7.2 Kiln seasoned and chemically treated hollock wood sqm 1949.65
9.7.3 Ply wood 5 ply, 9 mm thick
9.7.3.1 Decorative plywood both side decorative veneer
(Type - I) conforming to IS 1328 BWR type sqm 2256.55
9.7.3.2 Decorative plywood one side decorative veneer
and commercial veneer on other face (Type 1)
conforming to IS 1328 BWR Type sqm 2288.95
9.7.4 Ply wood 7 ply, 9 mm thick
9.7.4.1 Decorative plywood one side decorative veneer
and commercial veneer on other face (Type 1)
conforming to IS 1328 BWR Type sqm 2418.70
9.7.5 Particle Board 12 mm thick
9.7.5.1 Plain particle board flat pressed, 3 layer or graded
wood particle board medium density Grade I, IS :
3087 marked sqm 1345.10

No.
9.7.5.2 Veneered flat pressed three layer or graded wood

particle board with commercial veneering on both
sides conforming to IS:3097, grade I sqm 1688.90
9.7.5.3 Pre-laminated particle board with decorative
lamination on one side and balancing lamination
on other side, Grade I, Type II IS: 12823 marked sqm 1753.80
9.7.5.4 Pre-laminated particle board with decorative
lamination on both sides, Grade I, Type II, IS:12823
marked sqm 1810.55
9.7.6 Coir Veneer Board (conforming to IS 14842)
9.7.6.1 12 mm thick sqm 1964.60
9.7.7 Float glass panes
9.7.7.1 4 mm thick glass pane (weight not less than
10 kg per sqm) sqm 1792.55
9.7.7.2 5.0 mm thick glass panes (weight not less than
12.5 kg per sqm) sqm 2116.90
9.7.8 Fly proof stainless steel grade 304 wire gauge with 0.5 mm
dia. wire and 1.4mm wide aperture with matching wood
beading sqm 1458.60
9.9 Providing and fixing glazed shutters for doors, windows and clerestory
windows using 4 mm thick float glass panes, including ISI marked M.S.
pressed butt hinges bright finished of required size with necessary
screws.
9.9.1 Second class teak wood
9.9.1.1 35 mm thick sqm 4353.75
9.9.1.2 30 mm thick sqm 3961.20
9.9.2.1 35 mm thick sqm 2951.35
9.9.2.2 30 mm thick sqm 2753.80
9.9.3 Kiln seasoned selected planks of sheesham wood
9.9.3.1 35 mm thick sqm 3874.15
9.9.3.2 30 mm thick sqm 3547.75
9.10 Providing and fixing factory made laminated veneer lumber glazed shutter
conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick
float glass panes for doors, windows and clerestory windows fixing
with butt hinges of required size with necessary screws, all as per
directions of Engineer-in-charge. (Note:- Butt hinges and necessary
screws shall be paid separately)
9.10.1 30 mm thick shutters sqm 2572.50
9.11 Extra for providing heavy sheet float glass panes instead of ordinary
float glass in glazed doors, windows and clerestory window shutters.
(Area of opening for glass panes excluding portion inside rebate shall
be measured)
9.11.1 5.0 mm thick instead of 4 mm thick. sqm 267.60

No.
9.12 Extra for providing frosted glass panes 4 mm thick instead of ordinary
float glass panes 4 mm thick in doors, windows and clerestory window
shutters. (Area of opening for glass panes excluding portion inside rebate
shall be measured). sqm 214.05
9.13 Deduct for providing pin headed glass panes instead of ordinary float
glass panes weighing 4 mm thick in doors, windows and clerestory
windows shutters (Area of opening for glass panes excluding portion
inside rebate shall be measured). sqm 6.70
9.14 Extra for providing ISI marked Stainless Steel butt hinges instead of
M.S. pressed butt hinges bright finished of required size with necessary
screws. (Shutter area to be measured). sqm 126.50
9.15 Deduct for not providing hinges in doors, windows or clerestory window
shutters with :
9.15.1 Stainless steel butt hinges with stainless steel screws :
9.15.1.1 For 2nd class teak wood and other class of
wood shutters sqm 181.60
9.15.2 ISI marked M.S. pressed butt hinges bright finished of
required size.
9.15.2.1 For 2nd class teak wood and other class of wood
shutters sqm 55.15
9.16 Providing and fixing 25 mm thick shutters for cup board etc. :
9.16.1 Panelled or panelled & glazed shutters :
9.16.1.1 Second class teak wood including ISI marked
anodised aluminium butt hinges with necessary
screws sqm 3794.85
9.16.1.2 Second class teak wood including iSi marked
nickel plated bright finished M.S. piano hinges
with necessary screws sqm 3937.20
9.16.2 Glazed shutters :
anodized aluminium butt hinges with necessary
screws sqm 3646.15
nickel plated bright finished M.S. piano hinges
9.17 Providing and fixing flat pressed 3 layer particle board medium density
exterior grade (Grade I) or graded wood particle board IS : 3087 marked,
to frame, backing or studding with screws etc. complete (Frames,
backing or studding to be paid separately):
9.17.1 12 mm thick sqm 643.50
9.17.2 18 mm thick sqm 915.60

No.
9.18 Providing and fixing Pre-laminated flat pressed 3 layer (medium density)
particle board or graded wood particle board IS : 3087 marked, with one
side decorative and other side balancing lamination Grade I, Type II
exterior grade IS : 12823 marked, in shelves with screws and fittings
wherever required, edges to be painted with polyurethane primer (fittings
to be paid separately).
9.18.1 18 mm thick sqm 1193.20
9.18.2 25 mm thick sqm 1548.45
9.20 Providing and fixing ISI marked flush door shutters conforming to IS :
2202 (Part I) decorative type, core of block board construction with
frame of 1st class hard wood and well matched teak 3 ply veneering
with vertical grains or cross bands and face veneers on both faces of
shutters.
9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges
9.20.3 25 mm thick (for cupboard) including ISI marked nickel plated
bright finished M.S. Piano hinges IS : 3818 marked with
necessary screws sqm 2464.70
9.21 Providing and fixing ISI marked flush door shutters conforming to IS :
2202 (Part I) non-decorative type, core of block board construction with
frame of 1st class hard wood and well matched commercial 3 ply
veneering with vertical grains or cross bands and face veneers on both
faces of shutters:
9.21.3 25 mm thick (for cupboard) including ISI marked nickel plated
bright finished M.S. piano hinges with necessary screws sqm 1782.35
9.22 Extra for Providing and fixing flush doors with decorative veneering instead
of non decorative ISI marked flush door shutters conforming to IS: 2202
(Part I)
9.22.1 On one side only sqm 441.50
9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm
minimum depth on all edges of flush door shutters (over all area of door
shutter to be measured). sqm 401.40
9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush
doors (cost of glass excluded) (overall area of door shutter to be
measured):
9.24.1 Rectangular or square sqm 173.95
9.24.2 Circular sqm 180.60

No.
9.25 Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters
(overall area of door shutters to be measured).
9.25.1 Decorative type door sqm 354.55
9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to
be measured). sqm 93.65
9.27 Providing and fixing wire gauge shutters using galvanized M.S. wire
gauge of average width of aperture 1.4 mm in both directions with wire
of dia 0.63 mm, for doors, windows and clerestory windows with hinges
and necessary screws :
9.27.1 35 mm thick shutters
9.27.1.1 with ISI marked M.S. pressed butt hinges bright
finished of required size
9.27.1.1.1 Second class teak wood sqm 4221.20
9.27.1.1.2 Kiln seasoned and chemically treated
hollock wood sqm 2979.50
9.27.1.1.3 Kiln seasoned selected class of
sheesham wood sqm 3796.15
9.27.1.2 With ISI marked stainless steel butt hinges of
required size
9.27.1.2.2 Kiln seasoned and chemically
treated hollock wood sqm 3106.00
required size

No.
9.31 Providing and fixing wire gauge laminated veneer lumber shutters
conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using
galvanised wire gauge with average width of aperture 1.4 mm in both
directions with wire of dia 0.63 mm as per IS :1568, for doors, windows
and clerestory windows fixing with butt hinges of required size with
necessary screws, as per directions of Engineer-in-charge: (Note:- Butt
hinges and necessary screws shall be paid separately)
MISCELLANEOUS-WOOD WORK

9.40 Providing and fixing wooden moulded beading to door and window frames
with iron screws, plugs and priming coat on unexposed surface etc.
complete :
9.40.1 2nd class teak wood
9.40.1.1 50x12 mm metre 184.60
9.40.1.2 50 x 20 mm metre 232.15
9.40.2.1 50x12 mm metre 149.20
9.40.2.2 50x20 mm metre 173.15
9.41 Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart
(frames to be paid separately), including fixing 50x12 mm beading
complete with :
9.42 Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3
layer or graded wood particle board medium density grade I, IS : 3087
marked, including top cover of 6 mm commercial ply wood conforming
to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type)
curtain rod with nickel plated brackets, including fixing with 25x3 mm
No.
M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size
100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs
75 mm long etc. all complete. metre 505.95
9.43 Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer
board ISI marked IS : 14842, including top cover of 6 mm coir veneer
board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with
nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm
long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm
x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all
complete. metre 632.65
9.44 Extra for using veneered particle board conforming to IS 3097 Grade I, in
item of pelmet 18mm thick 150mm wide.
9.44.1 Non decorative veneer on both sides metre 33.20
9.44.2 Particle board with decorative veneering on both sides metre 107.05
9.45 Providing and fixing teak wood lipping of size 25x3 mm in pelmet. metre 60.10
9.46 Providing and fixing chromium plated brass curtain rod having wall
thickness of 1.25mm with two chromium plated brass brackets fixed
with C.P. brass screws and PVC sleeves etc., wherever necessary
complete :
9.46.1 12 mm dia metre 272.80
9.46.2 20 mm dia metre 373.15
9.46.3 25 mm dia metre 480.15
9.47 Providing and fixing nickel plated M.S. pipe curtain rods with nickel
plated brackets :
9.47.1 20 mm dia (heavy type) metre 155.65
9.47.2 25 mm dia (heavy type) metre 162.35
9.48 Providing and fixing M.S. grills of required pattern in frames of windows
etc. with M.S. flats, square or round bars etc. including priming coat
with approved steel primer all complete.
9.48.1 Fixed to steel windows by welding kg 165.30
9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. kg 183.50
9.49 Providing and fixing expanded metal 20x60 mm strands 3.25 mm wide
and 1.6mm thick for windows etc. including 62 x19 mm beading of II nd
class teak wood and priming coat with approved steel primer all
9.50 Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of
weight not less than 7.75 Kg per sqm to window frames etc. including
62x19 mm beading of second class teak wood and priming coat with
approved steel primer all complete. sqm 1448.35
9.51 Providing and fixing fly proof galvanized M.S. wire gauge to windows
and clerestory windows using wire gauge with average width of aperture
1.4 mm in both directions with wire of dia 0.63 mm all complete.
9.51.1 With 2nd class teak wood beading 62X19 mm sqm 1133.35
9.51.2 With 12 mm mild steel U beading sqm 781.25

No.
9.52 Deduct for fixing 75x25 mm hard drawn steel wire fabric of weight not
less than 7.75 Kg per sqm in panelled and glazed door and window
shutter instead of glass sheet 4 mm thick. sqm 173.95
9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to
frame with 10 mm diameter bolts, nuts and wooden plugs and embedding
in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse
sand : 6 graded stone aggregate 20mm nominal size). each 179.20
9.54 Providing beams including hoisting, fixing in position and applying wood
preservative for the unexposed surfaces, etc. complete with :
9.54.1 Sal wood cum 93844.40
9.54.2 Hollock wood cum 59720.35
BRIGHT FINISHED M.S. FITTINGS
9.55 Providing and fixing ISI marked M.S. pressed butt hinges bright finished
with necessary screws etc. complete :
9.55.1 125x65x2.12 mm each 46.25
9.55.2 100x58x1.90 mm each 37.30
9.55.3 75x47x1.70 mm each 31.05
9.55.4 50x37x1.50 mm each 15.65
9.56 Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges
9.56.1 125x90x4.00 mm each 56.30
9.56.2 100x75x3.50 mm each 48.00
9.56.3 75x60x3.10 mm each 36.25
9.56.4 50x40x2.50 mm each 19.80
Note: - In coastal areas, M.S. heavy weight butt hinges or stainless
steel hinges shall be used.
COPER OXIDISED MILD STEEL FITTINGS (COPPER OXIDISED AS
PER IS: 1378)
9.57 Providing and fixing ISI marked oxidised M.S. pressed butt hinges with
necessary screws etc. complete.
9.57.1 125x65x2.12 mm each 45.95
9.57.2 100x58x1.90 mm each 38.20
9.57.3 75x47x1.70 mm each 32.30
9.57.4 50x37x1.50 mm each 16.30
9.58 Providing and fixing ISI marked oxidised M.S. pressed Parliamentary
hinges with necessary screws etc. complete :
9.58.1 150x125x27x2.80 mm each 75.20
9.58.2 125x125x27x2.80 mm each 71.90
9.58.3 100x125x27x2.80 mm each 61.45
9.58.4 75x100x20x2.24 mm each 54.05

No.
9.59 Providing and fixing ISI marked oxidised M.S. single acting spring hinges
9.59.1 150 mm each 244.75
9.59.2 125 mm each 218.00
9.59.3 100 mm each 189.75
9.60 Providing and fixing oxidised M.S. double acting spring hinges with
necessary screws etc. complete.
9.60.1 150 mm each 270.20
9.60.2 125 mm each 235.65
9.60.3 100 mm each 216.50
9.61 Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel
plating and fixing with necessary screws etc., complete.
9.61.1 Overall width 35 mm metre 270.95
9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with
nuts and screws etc. complete :
9.62.1 300x16 mm each 183.30
9.62.2 250x16 mm each 170.00
9.63 Providing and fixing ISI marked oxidised M.S. tower bolt black finish,
(Barrel type) with necessary screws etc. complete :
9.63.1 250x10 mm each 74.15
9.63.2 200x10 mm each 60.55
9.63.3 150x10 mm each 52.55
9.63.4 100x10 mm each 38.70
9.64 Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock
conforming to IS : 7534 with necessary screws bolts, nut and washers
etc. complete. each 104.70
9.65 Providing and fixing ISi marked oxidised M.S. door latches conforming
to IS:5930 with screws etc. complete :
9.65.1 300x20x6 mm each 81.75
9.65.2 250x20x6 mm each 68.40
9.66 Providing and fixing ISI marked oxidised M.S. handles conforming to
IS:4992 with necessary screws etc. complete :
9.66.1 125 mm each 34.85
9.66.2 100 mm each 27.95
9.66.3 75 mm each 23.90

No.
9.67 Providing and fixing oxidised M.S. hasp and staple (safety type)
conforming to IS : 363 with necessary screws etc. complete :
9.67.1 150 mm each 28.75
9.67.2 115 mm each 25.60
9.67.3 90 mm each 21.70
9.68 Providing and fixing oxidised M.S. casement stays (straight peg type)
with necessary screws etc. complete.
9.68.1 300 mm weighing not less than 200 gms each 58.80
9.69 Providing and fixing oxidised M.S. Safety chain with necessary fixtures
for doors, (weighting not less than 450 gms) each 88.50
STAINLESS STEEL FITTINGS
9.70 Providing and fixing IS : 12817 marked stainless steel butt hinges with
stainless steel screws etc. complete :
9.70.1 125x64x1.90 mm each 84.50
9.70.2 100X58X1.90 mm each 74.60
9.70.3 75x47x1.80 mm each 56.60
9.70.4 50x37x1.50 mm each 32.25
9.71 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy
weight) with stainless steel screws etc. complete :
9.71.1 125x64x2.50 mm each 95.90
9.71.2 100x60x2.50 mm each 77.30
9.71.3 75x50x2.50 mm each 62.60
BRASS FITTINGS
9.72 Providing and fixing bright finished brass butt hinges with necessary
screws etc. complete :
9.72.1 125x85x5.5 mm (heavy type) each 226.85
9.72.3 100x85x5.5 mm (heavy type) each 173.60
9.72.5 75x65x4 mm (heavy type) each 145.40
9.73 Providing and fixing bright finished brass parliamentary hinges with
necessary screws etc. complete :
9.73.1 150x125x27x5 mm each 392.40

No.
9.73.2 125x125x27x5 mm each 350.95

9.73.3 100x125x27x5 mm each 322.85
9.73.4 75x100x20x3.2 mm each 286.45
9.74 Providing and fixing bright finished brass tower bolts (barrel type) with
necessary screws etc. complete :
9.74.1 250x10 mm each 373.65
9.74.2 200x10 mm each 299.85
9.74.3 150x10 mm each 231.65
9.74.4 100x10 mm each 159.65
9.75 Providing and fixing bright finished brass door latch with necessary screws
etc. complete :
9.75.1 300x16x5 mm each 272.40
9.75.2 250x16x5 mm each 259.00
9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock
with 6 levers and a pair of lever handles of approved quality with necessary
9.77 Providing and fixing bright finished brass 100 mm mortice latch with one
dead bolt and a pair of lever handles of approved quality with necessary
9.78 Providing and fixing bright finished brass night latch of approved quality
including necessary screws etc. complete. each 993.75
9.79 Providing and fixing special quality bright finished brass cupboard or
ward robe locks with four levers of approved quality including necessary
screws etc. complete.
9.79.1 40 mm each 251.20
9.79.2 50 mm each 291.30
9.79.3 65 mm each 298.00
9.79.4 75 mm each 318.10
9.80 Providing and fixing 50 mm bright finished brass cup board or wardrobe
knob of approved quality with necessary screws. each 62.70
9.81 Providing and fixing bright finished brass handles with screws etc.
complete:
9.81.1 125 mm each 204.65
9.81.2 100 mm each 189.45
9.81.3 75 mm each 149.35
9.82 Providing and fixing bright finished brass hanging type floor door stopper
with necessary screws, etc. complete. each 106.70
9.83 Providing and fixing aluminium die cast body tubular type universal
hydraulic door closer (having brand logo with ISI, IS : 3564, embossed
on the body, door weight upto 35 kg and door width upto 700 mm), with
necessary accessories and screws etc. complete. each 1003.50

No.
9.84 Providing and fixing aluminium extruded section body tubular type
universal hydraulic door closer (having brand logo with ISi, IS : 3564,
embossed on the body, door weight upto 36 kg to 80 kg and door width
from 701 mm to 1000 mm), with double speed adjustment with necessary
accessories and screws etc. complete. each 851.60
9.85 Providing and fixing bright finished brass casement window fastener
with necessary screws etc. complete. each 75.70
9.86 Providing and fixing bright finished brass casement stays (straight peg
type) with necessary screws etc. complete :
9.87 Providing and fixing bright finished brass hasp and staple (safety type)
9.87.1 150 mm each 118.10
9.87.2 115 mm each 106.95
9.87.3 90 mm each 94.20
CHROMIUM PLATED BRASS FITTINGS
9.88 Providing and fixing chromium plated brass 100 mm mortice latch and
lock with 6 levers and a pair of lever handles of approved quality with
necessary screws etc. complete. each 806.45
9.89 Providing and fixing chromium plated brass night latch of approved quality
including necessary screws etc. complete. each 846.55
9.90 Providing and fixing special quality chromium plated brass cupboard
locks with six levers of approved quality including necessary screws
etc. complete.
9.90.1 Size 40 mm each 257.85
9.90.2 Size 50 mm each 271.25
9.90.3 Size 65 mm each 304.70
9.90.4 Size 75 mm each 338.15
9.91 Providing and fixing chromium plated brass 50 mm cupboard or wardrobe
knobs with nuts complete. each 121.60
9.92 Providing and fixing chromium plated brass handles with necessary
screws etc. complete:
9.92.1 125 mm each 226.10
9.92.2 100 mm each 198.85
9.92.3 75 mm each 178.75
9.93 Providing and fixing chromium plated brass casement window fastener
with necessary screws etc. complete. each 140.15

No.
9.94 Providing and fixing chromium plated brass casement stays (straight
peg type) with necessary screws etc. complete :
ANODISED ALUMINIUM FITTINGS (ALL FITTINGS SHALL BE ISI

MARKED)
9.95 Providing and fixing ISI marked aluminium butt hinges anodised (anodic
coating not less than grade AC 10 as per IS: 1868) transparent or dyed
to required colour or shade with necessary screws etc. complete:
9.95.1 125x75x4 mm each 136.60
9.95.2 125x63x4 mm each 114.25
9.95.3 100x75x4 mm each 104.90
9.95.4 100x63x4 mm each 95.65
9.95.5 100x63x3.2 mm each 88.45
9.95.6 75x63x4 mm each 77.10
9.95.7 75x63x3.2 mm each 70.55
9.95.8 75x45x3.2 mm each 66.50
Note :- Aluminum hinges shall not be used in wooden shutters, stainless
steel hinges shall be preferred.
9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised
(anodic coating not less than grade AC 10 as per IS : 1868),
transparent or dyed to required colour or shade, with nuts and screws
etc. complete :
9.96.1 300x16 mm each 257.15
9.96.2 250x16 mm each 231.70
9.97 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed
to required colour or shade, with necessary screws etc. complete :
9.97.1 300x10 mm each 116.80
9.97.2 250x10 mm each 103.55
9.97.3 200x10 mm each 90.00
9.97.4 150x10 mm each 75.00
9.97.5 100x10 mm each 58.15
9.98 Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed
to required colour and shade, with necessary screws bolts, nut and
washers etc. complete. each 85.95

No.
9.99 Providing and fixing 50 cm long aluminium kicking plate of size 100x3.15
mm, anodised (anodic coating not less than grade AC 10 as per IS :
1868) transparent or dyed to required colour or shade, with necessary
9.100 Providing and fixing aluminium handles, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed
to required colour or shade, with necessary screws etc. complete :
9.100.1 125 mm each 59.65
9.100.2 100 mm each 52.85
9.100.3 75 mm each 45.90
9.101 Providing and fixing aluminium hanging floor door stopper, ISI marked,
anodised (anodic coating not less than grade AC 10 as per IS : 1868)
transparent or dyed to required colour and shade, with necessary screws
etc. complete.
9.101.1 Single rubber stopper each 33.95
9.101.2 Twin rubber stopper each 62.05
9.102 Providing and fixing aluminium casement stays, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868) transparent
or dyed to required colour and shade, with necessary screws etc.
9.103 Providing and fixing bright finished brass 100 mm mortice latch and
lock, ISI marked, with six levers and a pair of anodised (anodic coating
not less than grade AC 10 as per IS : 1868) aluminium lever handles of
approved quality with necessary screws etc. complete. each 748.65
9.104 Providing and fixing aluminium tee channels (heavy duty) with rollers &
stop end in pelmets as curtain rod. metre 139.35
GYPSUM BOARD PARTITIONS
9.105 Providing and fixing partition upto ceiling height consisting of G.I. frame and
required board, including providing and fixing of frame work made of special
section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/
sqm(both side inclusive), consisting of floor and ceiling channel 50mm
wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor
and ceiling at the spacing of 610 mm centre to centre with dash fastener of
12.5 mm dia meter 50 mm length or suitable anchor fastener or metal
screws with nylon plugs and the studs 48 mm wide having one flange of 34
mm and other flange 36 mm and 0.50 mm thick fixed vertically within
flanges of floor and ceiling channel and placed at a spacing of 610 mm
centre to centre by 6 mm dia bolts and nuts, including fixing of studs along
both ends of partition fixed flush to wall with suitable anchor fastener or
metal screws with nylon plugs at spacing of 450 mm centre to centre, and
fixing of boards to both side of frame work by 25 mm long dry wall screws
on studs, floor and ceiling channels at the spacing of 300 mm centre to
centre. The boards are to be fixed to the frame work with joints staggered
to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width
(0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120
gms/sqm(both side inclusive)) to be provided at the horizontal joints of two

No.
boards, fixed to the studs using metal to metal flat head screws, including
jointing and finishing to a flush finish with recommended jointing compound,
jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint
finisher and two coats of primer suitable for board as per manufacture's
specification and direction of engineer in charge all complete.
9.105.1 75 mm overall thickness partition with 12.5 mm thick double
skin fire rated Glass Reinforced Gypsum (GRG) plaster
board conforming to IS: 2095: (part 3) : 1996 (Board with
BIS certification marks) sqm 1741.15
9.105.2 75mm overall thickness partition with 12.5 mm thick double
skin tapered edged plain Gypsum plaster board conforming :
to IS 2095: (part 1) : 1996 (Board with BIS certification
marks) sqm 1513.70
9.105.3 66mm overall thickness Partition with 8mm thick double skin
Calcium Silicate Board made with Calcareous & Siliceous
materials reinforced with cellulose fiber manufactured through
autoclaving process with Compressive Strength 225 kg/sq.cm,
Bending Strength 100 kg./ sq.cm sqm 1808.05
9.105.4 66mm overall thickness partition using 8mm thick double
skin multipurpose cement board reinforced with cellulose fibre
manufactured through autoclaving process (High pressure
steam cured) as per IS : 14862 with suitable fibre cement
screws sqm 1687.60
9.105.5 66 mm overall thickness partition using 8 mm thick double
skin multipurpose cement bonded wood particle board
manufactured as per IS: 14276 with suitable cement bonded
board screws sqm 1674.25
9.106 Providing and fixing PTMT handles with necessary screws etc. complete.
9.106.1 125x34x24 mm weighing not less than 23 gms each 40.20
9.107 Providing and fixing PTMT Butt hinges with necessary screws etc.
complete.
9.107.1 75x60x10 mm fitted with 5.5 mm dia M.S. Bright Bar Rod
9.107.2 100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod
9.108 Providing and fixing PTMT Tower Bolts with 12 mm one piece rod inside
and necessary screws etc., complete.
9.109 Providing and fixing PTMT door catcher of length 72 mm and dia. of 42
mm with suitable washers weighing not less than 33 gms each 36.75
9.110 Providing and fixing Bamboo jaffery/ fencing consisting of superior quality
25mm dia (Average) half cut bamboo placed vertically and fixed together
with three numbers horizontal running members of hollock wood in
scantling of section 50X25 mm, fixed with nails and G.I wire on existing
support complete as per direction of Engineer-in-charge. sqm 576.15

No.
9.111 Providing and fixing wooden moulded corner beading of triangular shape
to the junction of panelling etc. with iron screws, plugs and priming coat
on unexposed surface etc. complete 2nd class teak wood.
9.111.1 50x50 mm (base and height) metre 250.25
9.112 Providing and fixing 2nd class teak wood lipping/ moulded beading or taj
beading of size 18X5 mm fixed with wooden adhesive of approved quality
and screws/nails on the edges of the Pre-laminated particle board as
per direction of Engineer-in-charge. metre 78.85
9.113 Providing and fixing bright finished 100 mm mortice lock with 6 levers
without pair of handles of approved quality for aluminium door, with
necessary screws etc complete as per direction of Engineer- in-charge. each 637.05
9.114 Providing and fixing magnetic catcher of approved quality in cupboard /
ward robe shutters, including fixing with necessary screws etc. complete.
9.114.1 Triple strip vertical type each 39.05
9.114.2 Double strip (horizontal type) each 31.05
9.115 Providing and fixing powder coated telescopic drawer channels 300 mm
long with necessary screws etc. complete as per directions of Engineer-
in-charge. one set 339.75
9.116 Providing and fixing sliding arrangement in racks/ cupboards/cabinets
shutter by with stainless steel rollers to run inside C or E aluminium
channel section (The payment of C or E channel shall be made separately) each 14.80
9.117 Providing and fixing factory made uPVC door frame made of uPVC
extruded sections having an overall dimension as below (tolerance
±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door
frame to be Jointed with galvanized brackets and stainless steel screws,
joints mitred and Plastic welded. The hinge side vertical of the frames
reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1
mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame
complete as per manufacturer’s specification and direction of Engineer-
in-charge
9.117.1 Extruded section profile size 48x40 mm metre 221.65
9.117.2 Extruded section profile size 42x50 mm metre 267.45
9.118 Providing and fixing to existing door frames.
9.118.1 24 mm thick factory made PVC door shutters made of styles
and rails of a uPVC hollow section of size 59x24 mm and wall
thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides.
The styles and rails mitred and joint at the corners by means
of M.S. galvanised/ plastic brackets of size 75x220 mm having
wall thickness 1.0 mm and stainless steel screws. The styles
of the shutter reinforced by inserting galvanised M.S. tube of
size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The
lock rail made up of 'H' section, a uPVC hollow section of size
100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the
shutter styles by means of plastic/galvanised M.S. 'U' cleats.
The shutter frame filled with a uPVC multi-chambered single

No.
panel of size not less than 620 mm, having over all thickness
of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels
filled vertically and tie bar at two places by inserting horizontally
6 mm galvanised M.S. rod and fastened with nuts and
washers, complete as per manufacturer's specification and
direction of Engineer-in-charge. (For W.C. and bathroom door
shutter). sqm 1760.70
9.118.2 30 mm thick factory made Polyvinyl Chloride (PVC) door
shutter made of styles and rails of a uPVC hollow section of
size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with
inbuilt decorative moulding edging on one side. The styles
and rails mitred and joint at the corners by means of M.S.
galvanised/ plastic brackets of size 75x220 mm having wall
thickness 1.0 mm and stainless steel screws. The styles of
the shutter reinforced by inserting galvanised M.S. tube of
size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The
lock rail made up of 'H' section, a uPVC hollow section of size
100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the
shutter styles by means of plastic/ galvanised M.S. 'U' cleats.
The shutter frame filled with a uPVC multi-chambered single
panel of size not less than 620 mm, having over all thickness
of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels
filled vertically and tie bar at two places by inserting horizontally
6 mm galvanised M.S. rod and fastened with nuts and
washers, complete as per manufacturer's specification and
direction of Engineer-in-charge. sqm 1978.65
9.118.3 25 mm thick PVC flush door shutters made out of a one piece
Multi chamber extruded PVC section of the size of 762 mm X
25 mm or less as per requirement with an average wall
thickness of 1 mm (± 0.3 mm). PVC foam end cap of size
23x10 mm are provided on both vertical edges to ensure the
overall thickness of 25 mm. M.S. tube having dimensions 19
mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the
hinge side of the door. Core of the door shutter should be filled
with High Density Polyurethane foam. The Top & Bottom edges
of the shutter are covered with an end-cap of the size 25 mm
X 11 mm. Door shutter shall be reinforced with special
polymeric reinforcements as per manufacturer’s specification
and direction of Engineer-in-charge to take up necessary
hardware and fixtures. Stickers indicating the locations of
hardware will be pasted at appropriate places sqm 2582.30
9.119 Providing and fixing factory made P.V.C. door frame of size 50x47 mm
with awall thickness of 5 mm, made out of extruded 5mm rigid PVC
foam sheet, mitred at corners and joined with 2 Nos of 150 mm long
brackets of 15x15 mm M.S. square tube, the vertical door frame profiles
to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM
rubber gasket weather seal to be provided through out the frame. The
door frame to be fixed to the wall using M.S. screws of 65/100 mm size,
complete as per manufacturer’s specification and direction of Engineer-
in-Charge. metre 391.65

No.
9.120 Providing and fixing factory made panel PVC door shutter consisting of
frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm
x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame
shall have a coat of steel primers of approved make and manufacture.
M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of
size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and
20 mm shall be tapered in 45 degree angle on both side forming styles
and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat
and 20 mm shall be tapered in 45 degree on the inner side to form top
and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be
flat and 20 mm shall be tapered on both sides to form lock rail. Top,
bottom and lock rails shall be provided both side of the panel. 10 mm (5
mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert
for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to
be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm
(5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and
joined together with solvent cement adhesive. An additional 5 mm thick
PVC strip of 20 mm width is to be stuck on the interior side of the 'C'
Channel using PVC solvent adhesive etc. complete as per direction of
Engineer-in-charge, manufacturer's specification & drawing.
9.120.1 30 mm thick plain PVC door shutters sqm 2423.40
9.120.2 30 mm thick pre laminated PVC door shutters sqm 2423.40
9.121 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames
of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15
mm to receive shutter of 30 mm thickness. The laminate shall be moulded
with fire resistant grade unsaturated polyester resin and chopped mat.
Door frame laminate shall be 2mm thick and shall be filled with suitable
wooden block in all the three legs. The frame shall be covered with fiber
glass from all sides. M.S. stay shall be provided at the bottom to steady
the frame. metre 679.85
9.122 Providing and fixing to existing door frames.
9.122.1 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled
door shutter of required colour and approved brand and
manufacture, made with fire - retardant grade unsaturated
polyester resin, moulded to 3 mm thick FRP laminate for
forming hollow rails and styles, with wooden frame and suitable
blocks of seasoned wood inside at required places for fixing
of fittings, cast monolithically with 5 mm thick FRP laminate
for panels conforming to IS: 14856, including fixing to frames. sqm 3465.05
9.122.2 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door
shutter in different plain and wood finish made with fire
retardant grade unsaturated polyester resin, moulded to 3
mm thick FRP laminate all around, with suitable wooden
blocks inside at required places for fixing of fittings and
polyurethane foam (PUF)/Polystyrene foam to be used as
filler material throughout the hollow panel, casted
monolithically with testing parameters of F.R.P. laminate
conforming to table - 3 of IS: 14856, complete as per direction
of Engineer-in-charge. sqm 3931.95

No.
9.123 Providing and fixing factory made door frame (single rebate) made out of
single piece extruded solid PVC foam profile with homogenous fine
cellular structure having smooth outer integral skin having 62 mm width
& 32 mm thickness, frame will be mitred & Jointed with self driven self
tapping screws of size 38 mm x 4 mm & PVC solvent cement, including
fixing the frame to wall with suitable dia & length anchor fastener as per
manufacturer's specification and direction of Engineer-in-charge. metre 476.50
9.124 Providing and fixing factory made 30 mm thick door shutter made of
solid PVC foam profile. The styles & rails shall be of size 75 mm x 30
mm having wall thickness 5 mm. The styles, top & bottom rails shall
have one side wall thickness of 15 mm integrally extruded on the hinge
side of the profile for better screw holding power. The styles and rails
shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm,
painted with primer , all four corners of reinforcement to be welded or
sealed. Solid PVC extruded bidding (push fit type) will be set inside the
styles and the rails with a cavity, to receive single piece extruded 5mm
PVC sheet as panel. The styles and rails will be mitred cut and joint
with the help of PVC solvent cement & self driven self tapping screws.
Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with
wall thickness 5 mm & 15 mm integrally extruded in the middle of the
lock rail & fixed with styles with the help of PVC solvent cement & self
driven self tapping screws of size 100mm x 8 mm complete as per
manufacturer's specifications and direction of Engineer-in-charge.
9.124.1 Non decorative finish sqm 3028.85
9.124.2 Decorative finish (both side wood grained finish) sqm 3162.65
9.125 Providing and fixing PVC rigid foam sheet 1 mm thick on existing door
shutters (bathroom and W.C. doors) using synthetic rubber based
adhesive. sqm 1200.35
9.126 Providing and fixing 12 mm thick panelling or panelling and glazing in
panelled or panelled and glazed shutters for doors, windows and
clerestory windows (area of opening for panel inserts excluding portion
inside grooves or rebates to be measured). Panelling for panelled or
panelled and glazed shutters 25 mm to 40 mm thick.
9.126.1 Marine plywood conforming to IS: 710 sqm 2005.15
9.126.2 Fire retardant plywood conforming to IS: 5509 sqm 2256.55
9.127 Providing & Fixing decorative high pressure laminated sheet of plain /
wood grain in gloss / matt/ suede finish with high density protective
surface layer and reverse side of adhesive bonding quality conforming
to IS : 2046 Type S, including cost of adhesive of approved quality.
9.127.1 1.5 mm thick sqm 842.75
9.127.2 1.0 mm thick sqm 717.65
9.128 Providing and fixing factory made Fiberglass Reinforced plastics (F.R.P.)
chajja 4 mm thick of required colour, size and design made by Resin
Transfer Moulding (RTM) Machine Technology, resulting in void free
compact laminate in single piece, having smooth gradual slope curvature
for easy drainage of water and duly reinforced by 2 nos vertically and 1

No.
nos horizontally 50x2 mm thick M.S. flat with 12 mm in built hole for
grouting on the existing wall along with the 50 mm flanges duly inserted
and sealed in the wall complete in one single piece casted monolithically,
including all necessary fittings . The FRP Chajja should be manufactured
using unsaturated Polyester resin as per IS: 6746, duly reinforced with
fibre glass chopped strand mat (CSM) as per IS: 11551 complete with
protective Gel coat U/V coating on Top for complete resistance from the
extreme of temperature, weather & sunlight. Note - Only plan area of
chajjas shall be measured for making payment] sqm 4851.25
9.129 Providing and fixing cup board shutters 25 mm thick, with Pre-laminated
flat pressed three layer particle board or graded wood particle board IS:
12823 marked, exterior grade (Grade l Type ll), having one side decorative
lamination and other side balancing lamination, including IInd class teak
wood lipping of 25 mm wide x12 mm thick with necessary screws and
bright finished stainless steel piano hinges, complete as per direction
of the Engineer-in-Charge sqm 1928.90
9.130 Providing and fixing cup board shutters with 25 mm thick veneered particle
board IS : 3097 marked, exterior grade (Grade I), of approved make,
including IInd class teak wood lipping of 25 mm wide x 12 mm thick
with necessary screws and bright finished stainless steel piano hinges,
9.130.1 With decorative veneering on one side and commercial
veneering on other side sqm 1647.95
9.130.2 With non decorative veneering on both sides sqm 1547.60
9.131 Providing and fixing factory made shutters of Pre-laminated particle board
flat pressed three layer or graded wood particle board with one side
decorative finish and other side balancing lamination conforming to IS:
12823 Grade l Type ll, of approved design, and edges sealed with water
resistant paint and lipped with aluminium 'U' type edge beading all-
round the shutter, including fixing with angle cleat, grip strip, cadmium
plated steel screws, including fixing of aluminium hinges 100x63x4 mm
etc. complete as per architectural drawing and direction of Engineer-in-
Charge (Cost of 'U' beading and hinges will be paid for separately).
9.131.1 25 mm thick sqm 1531.45
9.132 Providing and fixing aluminum U beading of required size to Pre-laminated/
flush door shutter, including fixing etc. complete as per direction of
Engineer-in-charge. kg 517.80
9.133 Providing and fixing, in position concealed G.I. section for wall paneling
using board of required thickness fixed on the 'W' profile (0.55 mm
thick) having a knurled web of 51.55 mm and two flanges of 26 mm
each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel
having one flange of 20 mm and another flange of 30 mm with thickness
of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the
floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully
threaded self-tapping dry wall screws. Board is fixed to the 'W' profile
with 25 mm countersunk ribbed head screws @ 200 mm C/C., all
complete as per the drawing & directions of engineer-in-charge, the
joints of the boards are finished with specially formulated jointing
compound and 48mm wide jointing tape to provide seamless finish.

No.
9.133.1 Tapered edge calcium silicate board made with calcareous &
siliceous materials reinforced with cellulose fiber manufactured
through autoclaving process to give stable crystalline structure
with compressive strength 225 kg/ sq.cm, Bending strength
100 kg/sq.cm.
9.133.1.1 10mm thick sqm 1420.45
9.133.2 Multipurpose cement board reinforced with suitable fibre
cement screw.
9.133.2.1 8 mm thick cement fibre board as per IS : 14862 sqm 1126.00
9.133.2.2 8 mm thick Cement bonded wood particle board
as per IS:14276 sqm 1118.65
9.133.3 Plain Gypsum plaster board conforming to IS: 2095 (Part -1) :
2011 (Board with BIS certification marks)
9.133.3.1 12.5 mm thick sqm 1030.35
9.134 Providing and fixing wire gauge shutters using stainless steel grade 304
wire gauge with wire of dia 0.5 mm and average width of aperture 1.4
mm in both directions for doors, windows and clerestory windows with
necessary screws :
required size

No.

required size
9.135 Providing and fixing fly proof stainless steel grade 304 wire gauge, to
windows and clerestory windows using wire gauge with average width
of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all
complete.
9.135.1 With 2nd class teak wood beading 62X19 mm sqm 1353.60
9.135.2 With 12 mm mild steel U beading sqm 1001.50
9.136 Providing and fixing fire resistant door frame of section 143 x 57 mm
having built in rebate made out of 16 SWG G.I. sheet (zinc coating not
less than 120 gm/sqm) duly filled with vermuculite based concrete mix,
suitable for mounting 60 minutes fire rated door shutters. The frame is
fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround
the frame and fixing with dash fastener of approved size and make,
including applying a coat of approved brand fire resistant primer etc.
complete as per direction of Engineer-in-charge (Dash fastener to be
paid for separately). metre 1444.30
9.137 Providing and fixing 50 mm thick glazed fire resistant door shutters of
60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified
as per laboratory approved by Engineer-in-charge, with suitable mounting
on door frame, consisting of vertical styles, lock rail, top rail 100 mm
wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc
coating not less than 120 gm/m2) duly filled FR insulation material and
fixing with necessary stainless steel ball bearing hinges of approved
make, including applying a coat of approved fire resistant primer etc. all
complete as per direction of Engineer-in-charge (panneling to be paid
for separately). sqm 6166.00
9.138 Providing and fixing glazing in fire resistant door shutters, fixed panels
& partitions etc., with G.I. beading made out of 1.6 mm thick G.I.
sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm
screwed with M4 x 38 mm SS screws at distance 75 mm from the
edges and 150 mm c/c , including applying a coat of approved
fire resistant primer/powder coating of not less than 30 micron
on G.I. beading, & special ceramic tape of 5 x 20 mm size etc
complete in all respect as per NBC 2016, IS 16231 (Part 3):2016
and as per direction of Engineer-in-charge with glass of required
thickness having 60 minutes of fire resistance both integrity &
radiation control (EW60) and minimum 20 minutes of insulation
(EI20). The manufacturer have to give test report/certification of fire
glass and the glass should have the stamp showing the value of E,
EW & EI. The glass shall be tested in approved NABL accredited lab

No.
or by any other accreditation body which operates in accordance

with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for
testing and calibration scopes shall be eligible. The maximum
glazing size shall not be more than 1100x2200 mm (w x h) or 2.42
sqm. sqm 36050.45
9.139 Providing and fixing panic bar / latch (Double point) fitted with a single
body, Trim Latch & Lock on back side of the Panic Latch of reputed
brand and manufacture to be approved by the Engineer- in- charge, all
9.140 Providing and fixing plain lining with necessary screws/nuts & bolts/
nails, including a coat of approved primer on one face, and fixed on
wooden /steel frame work, complete as per direction of Engineer-in-
charge (Frame work shall be paid for separately).
9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type sqm 1040.80
9.141 Providing and fixing PVC Door Frame of size 50x47 mm with a wall
thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC
profile, with mitred cut joints and joint with 2 nos of PVC bracket of size
190 mm x 100 mm long arms of cross section size 35 x 15 mm & self
driven self taping screws, the vertical door profiles to be reinforced with
40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM
rubber gasket weather seal throughout the frame, including jointing 5
mm PVC frame strip with PVC solvent cement on the back of the profile.
The door frame to be fixed to the wall using 8 x100 mm long anchor
fasteners complete, all as per manufacturer's specification and direction
of Engineer -in- charge. metre 456.80
9.142 35 mm thick factory made Solid panel PVC Door shutter, made out of
single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having
styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of
which 75 mm shall be flat and 20 mm shall be tapered (on both side),
having one side thickness of 15 mm integrally extruded on the hinge side
of the profile for better screw holding power, including reinforcing with MS
tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered
cut & joint with the help of PVC solvent cement, self driven self tapping
screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of
cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece
extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of
which 75 mm to be flat and 20 mm to be tapered at both ends, having 15
mm solid core in middle of rail section integrally extruded, fixing the
styles & rails with the help of solvent and self driven self tapping screws
of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC
extruded sheet inserted in the door as panel, all complete as per
manufacturer's specification and direction of Engineer-in-charge.
9.142.1 Non decorative finish (matt finish) sqm 3240.80
9.142.2 Decorative finish (wood grained finish) sqm 3842.85
9.143 Providing and Fixing factory made uPVC door frame, made of uPVC
exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm
(± 0.2 mm), corners of the door frame to be mitred cut and jointed with
plastic brackets and stainless steel screws, reinforcing hinge side

No.
vertical of the frames with PVC profile of Size 28 mm x 30 mm having

wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of
125 mm long stainless steel hinges to the frame, fixing the frame with
jamb with required number & size of anchor dash fastners, all complete
as per manufacturer's specification and direction of Engineer-in-charge. metre 528.35
9.144 Providing and fixing 37 mm thick factory made PVC door shutter, styles
and rails made of PVC hollow section of size 100 mm x 37 mm with
wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles
and rails mitered cut and joint at the corners by means of 2 nos of
plastic brackets of size 75 mm x 220 mm at each corner and stainless
steel screws, reinforcing the hinge side of style by inserting PVC profile
of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail
of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed
to the vertical styles. Providing with PVC snapfit beads and panel of
size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and
fastening with nuts and washers complete, all as per manufacturer's
specification and direction of Engineer-in-charge. sqm 3518.85
9.145 Providing and Fixing factory made PVC door frame made of PVC extruded
sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2
mm). Both verticalssides of the frame reinforced with PVC profile of
cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and
75 mm x 200 mm long, including reinforcing both ends of the top frame
with PVC profile. PVC Door Frame and PVC reinforcement profile to be
mitred cut, jointed and fusion welded together, including providing and
fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the
frame with jamb with required nos & sizes of anchor dash fastener, all
complete as per manufacturer's specification and direction of engineer-
in-charge. metre 588.55
9.146 Providing and fixing 37 mm thick factory made PVC Door shutter, styles
and rails made of PVC hollow extruded printed and laminated section
having overall dimension 115 mm x 37 mm with wall thickness 2 mm (±
0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut
and joint at corners by inserting 2 nos PVC profile reinforcement of size
75 mm x 200 mm long with cross section size of 28 mm x 30 mm
having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements
to be fusion welded together. Only hinge side vertical style to be
reinforced with PVC profile reinforcement in full length. Printed and
laminated PVC lock rail of size 110 mm x 37 mm having wall thickness
2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after
inserting PVC profile reinforcement as in styles and rails, providing with
PVC snap fit beading, panels of 100 x 20 mm printed & laminated and
inserting 2 nos 6 mm dia bright steel rod horizontally with both side
threaded and tightened with check nuts and washers complete, all as
per manufacturer's specification and direction of engineer-in-charge. sqm 3786.45
9.147A Providing and fixing factory made uPVC white colour casement/casement
cum fixed glazed windows comprising of uPVC multi-chambered frame,
sash and mullion (where ever required) extruded profiles duly reinforced
with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll
forming process of required length (shape & size according to uPVC
profile), uPVC extruded glazing beads of appropriate dimension, EPDM

No.
gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white
powder coated) casement handles, G.I fasteners 100 x 8 mm size for
fixing frame to finished wall, plastic packers, plastic caps and necessary
stainless steel screws etc. Profile of frame & sash shall be mitred cut
and fusion welded at all corners, mullion (if required) shall be also fusion
welded including drilling of holes for fixing hardware's and drainage of
water etc. After fixing frame the gap between frame and adjacent finished
wall shall be filled with weather proof silicon sealant over backer rod of
required size and of approved quality, all complete as per approved
drawing & direction of Engineer-in-Charge. (Single / double glass panes
and silicon sealant shall be paid separately)
Note: For uPVC frame, sash and mullion extruded profiles minus 5%
tolerancein dimension i.e. in depth & width of profile shall be acceptable.
Variation in profile dimension in higher side shall be accepted
but no extra payment on this account shall be made.
9.147A.1 Casement window single panel with S.S. friction hinges (300
x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm &
sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm
and single glass pane glazing bead of appropriate dimension.
(Area of window upto 0.75 sqm.) sqm 9483.50
9.147A.2 Casement window double panels with S.S. friction hinges (300
x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm,
sash 47 x 68 mm & mullion 47 x 68 mm all having wall
thickness of 1.9 ± 0.2 mm and single glazing bead of
appropriate dimension. (Area of window above 0.75 sqm upto
1.50 sqm). sqm 8717.70
9.147A.3 Casement window double panels with top fixed with S.S. friction
hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50
mm, sash 47 x 68 mm & mullion 47 x 68 mm all
having wall thickness of 1.9 ± 0.2 mm and single glazing bead of
appropriate dimension. ( Area of window upto 2.50 sqm). sqm 6982.00
9.147A.4 Casement window single panel with S.S. friction hinges (400
x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash
67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm
and single glazing bead / double glazing bead of appropriate
dimension. (Area of window above 0.75 sqm.) sqm 9331.00
9.147A.5 Casement window double panels with S.S. friction hinges (350
x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash
/ mullion 67 x 80 mm both having wall thickness of 2.3 ±
0.2 mm and single glazing bead/ double glazing bead of
appropriate dimension. (Area of window above 1.50 sqm). sqm 9666.20
9.147A.6 Casement cum fixed panel window having both end single
casement panel, middle fixed panels and at top completely
fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made
of (big series) frame 67 x 60 mm , sash 67 x 80 mm &
mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm
and single glazing bead/double glazing bead of appropriate
dimension. (Area of window above 3.00 sqm upto 5.00 sqm). sqm 7242.25

No.
9.147B Providing and fixing factory made uPVC white colour fixed glazed
windows/ventilators comprising of uPVC multi-chambered frame and
mullion (where ever required) extruded profiles duly reinforced with 1.60
± 0.2 mm thick galvanized mild steel section made from roll forming
process of required length (shape & size according to uPVC profile),
uPVC extruded glazing beads of appropriate dimension, EPDM gasket,
G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic
packers, plastic caps and necessary stainless steel screws etc. Profile
of frame shall be mitred cut and fusion welded at all corners, mullion (if
required) shall be also fusion welded including drilling of holes for fixing
hardware's and drainage of water etc. After fixing frame the gap between
frame and adjacent finished wall shall be filled with weather proof silicon
sealant over backer rod of required size and of approved quality, all
complete as per approved drawing & direction of Engineer-in-Charge.
(Single / double glass panes and silicon sealant shall be paid separately).
tolerance in dimension i.e. in depth & width of profile shall be acceptable.
9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50
mm & mullion 47 x 68 mm both having wall thickness of 1.9 ±
0.2 mm and single glazing bead of appropriate dimension.
(Area upto 0.75 sqm.) sqm 6478.75
9.147C Providing and fixing factory made uPVC white colour casement/ Casement
cum fixed glazed door comprising of uPVC multi-chambered frame, sash
and mullion (where ever required) extruded profiles duly reinforced with
1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming
process of required length (shape & size according to uPVC profile),
uPVC extruded glazing beads of appropriate dimension, EPDM gasket,
zinc alloy (white powder coated) 3D hinges and one handle on each side
of panels along with zinc plated mild steel multi point locking having
transmission gear, cylinder with keeps and one side key, G.I fasteners
100 x 8 mm size for fixing frame to finished wall and necessary stainless
steel screws, etc. Profile of frame & sash shall be mitred cut and fusion
welded at all corners, mullion (if required) shall be also fusion welded
including drilling of holes for fixing hardware's and drainage of water etc.
After fixing frame the gap between frame and adjacent finished wall shall
be filled with weather proof silicon sealent over backer rod of required size
and of approved quality, all complete as per approved drawing & direction
of Engineer-in-Charge. (Single / double glass panes and silicon sealent
shall be paid separately).
tolerance in dimension i.e. in depth & width of profile shall be acceptable.
9.147C.1 Casement door with 3D hinges made of (big series) frame 67
x 64 mm & sash 67 x 110 mm both having wall thickness of
2.3 ± 0.2 mm and single glazing bead / double glazing bead
of appropriate dimension. (Area of door upto 2.00 sqm). sqm 9131.45
9.147C.2 Casement door with top hung ventilator with 3D and S.S. friction
hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64
mm, sash 67 x 110 mm & mullion 67 x 80 mm all having
wall thickness of 2.3 ±. 0.2 mm and single glazing bead /
double glazing bead of appropriate dimension.(Area of door
upto 2.50 sqm) sqm 9328.30

No.
9.147D Providing and fixing factory made uPVC white colour sliding glazed window
upto 1.50 m in height dimension comprising of uPVC multi-chambered
frame with in-built roller track and sash extruded profiles duly reinforced
profile), appropriate dimension of uPVC extruded glazing beads and
uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white
powder coated) touch locks with hook, zinc alloy body with single nylon
rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm
size for fixing frame to finished wall and necessary stainless steel screws
etc. Profile of frame & sash shall be mitred cut and fusion welded at all
corners, including drilling of holes for fixing hardware's and drainage of
water etc. After fixing frame the gap between frame and adjacent finished
wall shall be filled with weather proof silicon sealent over backer rod of
required size and of approved quality, all complete as per approved drawing
& direction of Engineer-in-Charge. (Single / double glass panes, wire
mesh and silicon sealent shall be paid separately)
Note: For uPVC frame and sash extruded profiles minus 5% tolerance
in dimension i.e. in depth & width of profile shall be acceptable.
9.147D.1 Two track two panels sliding window made of (small series)
frame 52 x 44 mm &sash 32 x 60 mm both having
wall thickness of 1.9 ± 0.2 mm and single glazing bead of
appropriate dimension. (Area of window upto 1.75 sqm) sqm 6709.60
9.147D.2 Three track three panels sliding window with fly proof SS
wire mesh (Two nos. glazed & one no. wire mesh panels)
made of (small series) frame 92 x 44 mm & sash 32 x 60 mm
both having wall thickness of 1.9 ± 0.2 mm and single glazing
bead of appropriate dimension (Area of window upto 1.75 sqm). sqm 8954.20
9.147D.3 Two track two panels sliding window made of (big series)
frame 67 x 50 mm & sash 46 x 62 mm both having wall
thickness of 2.3 ± 0.2 mm and single glazing bead / double
glazing bead of appropriate dimension . (Area of window
above 1.75 sqm
upto 2.50 sqm). sqm 6912.15
9.147D.4 Three track three panels sliding window with fly proof S.S
wire mesh (Two nos. glazed & one no. wire mesh panels)
made of (big series) frame 116 x 45 mm & sash 46 x 62 mm
both having wall thickness of 2.3 ± 0.2 mm and single glazing
bead / double glazing bead of appropriate dimension. (Area
of window above 1.75 sqm). sqm 8616.00
9.147D.5 Three track three panels sliding window made of (big series)
glazing bead of appropriate dimension. (Area of window above
1.75 sqm) sqm 8177.05
9.147E Providing and fixing factory made uPVC white colour sliding glazed window
above 1.50 m in height dimension comprising of uPVC multi-chambered
frame with in-built roller track and sash extruded profiles duly reinforced

No.

profile), appropriate dimension of uPVC extruded glazing beads, uPVC
extruded interlocks and uPVC extruded Inline sash adaptor (if required),
EPDM gasket, wool pile, zinc alloy (white powder coated) handle on
one side of extreme panel along with zinc plated mild steel multi point
locking having transmission gear with keeps, zinc alloy (white powder
coated) touch lock with hook (if required for wire mesh panel), stainless
steel (SS 304 grade) body with adjustable double nylon rollers (weight
bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing
frame to finished wall and necessary stainless steel screws etc. Profile
of frame & sash shall be mitred cut and fusion welded at all corners,
including drilling of holes for fixing hardware's and drainage of water etc.
After fixing frame the gap between frame and adjacent finished wall shall
be filled with weather proof silicon sealent over backer rod of required
size and of approved quality, all complete as per approved drawing &
direction of Engineer-in-Charge. (Single / double glass panes, wire mesh
and silicon sealent shall be paid separately).
in dimension i.e. in depth & width of profile shall be acceptable.
9.147E.1 Two track two panels sliding window made of (big series)
2.50 sqm
upto 4.00 sqm.) sqm 6861.60
9.147E.2 Two track four panels sliding window made of (big series)
4.00 sqm upto 8.00 sqm). sqm 5941.95
9.147F Providing and fixing factory made uPVC white colour sliding glazed door
comprising of uPVC multi-chambered frame with in-built roller track and
sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized
mild steel section made from roll forming process of required length
(shape & size according to uPVC profile), appropriate dimension uPVC
extruded glazing beads, uPVC extruded interlock and uPVC extruded
Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy
(white powder coated) handle with key on one side of extreme panels
along with zinc plated mild steel multi point locking having transmission
gear with keeps, zinc alloy (white powder coated) cresent lock (if
required), stainless steel (SS 304 grade) body with adjustable double
nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x
8 mm size for fixing frame to finished wall and necessary stainless steel
screws etc. Profile of frame & sash shall be mitred cut and fusion welded
at all corners, including drilling of holes for fixing hardware's and drainage
of water etc. After fixing frame the gap between frame and adjacent
finished wall shall be filled with weather proof silicon sealent over backer
rod of required size and of approved quality, all complete as per approved
drawing & direction of Engineer-in-Charge. (Single / double glass panes,
wire mesh and silicon sealent shall be paid separately).

No.
in dimension i.e. in depth & width of profile shall be acceptable. Variation
in profile dimension in higher side shall be accepted but no extra
payment on this account shall be made.
9.147F.1 Two track two panels sliding door made of (big series) frame
67 x 50 mm & sash 46 x 82 mm both having wall thickness
of 2.3 ± 0.2 mm and single glazing bead / double glazing
bead of appropriate dimension. (Area of door above 2.00
sqm upto
5.00 sqm) sqm 6005.00
9.147F.2 Two track four panels sliding door made of (big series) frame
67 x 50 mm & sash 46 x 82 mm both having wall thickness
of 2.3 ± 0.2 mm and single glazing bead / double glazing
bead of appropriate dimension. (Area of door above 8.00 sqm
upto
10.00 sqm). sqm 5332.85
9.147F.3 Three track three panels sliding door made of (big series)
thickness of 2.3 ± 0.2 mm and single glazing bead/ double
glazing bead of appropriate dimension. (Area of door above
5.00 sqm) sqm 6064.80
9.147F.4 Three track three panels sliding door with fly proof S.S wire
mesh (Two nos. glazed & one no. wire mesh panels) made of
(big series) frame 116 x 45 mm & sash 46 x 82 mm both
having wall thickness of 2.3 ± 0.2 mm and single glazing
bead / double glazing bead of appropriate dimension. (Area
of
door above 2.00 sqm upto 5.00 sqm) sqm 7774.55
9.148 Providing and fixing stainless steel (SS-304 grade) friction hinges to
the side/top hung uPVC windows, of approved quality, with necessary
stainless steel screws etc. as per direction of Engineer-in-charge.
9.148.1 200 x 19 x 1.9 mm each 299.90
9.148.2 250 x 19 x 1.9 mm each 333.35
9.148.3 300 x 19 x 1.9 mm each 353.40
9.148.4 350 x 19 x 1.9 mm each 487.20
9.148.5 400 x 19 x 1.9 mm each 513.95
9.149 Providing and fixing casement handle made of zinc alloyed (white powder
coated) for uPVC casement window with necessary screws etc.
9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for
uPVC sliding window with necessary screws etc. complete. each 154.35
9.151 Providing and fixing steel roller for uPVC sliding window with necessary
9.152 Providing and fixing steel roller for uPVC sliding door with necessary
9.153 Providing and fixing steel (white power coated) crescent lock for uPVC
sliding window/ door with necessary screws etc. complete. each 167.70

No.
9.154 Providing and fixing frame work for partitions/ wall lining etc. made of
50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and
floor in a grid pattern with spacing @ 60 cm centre to centre both ways
(vertically & horizontally) or at required spacing near opening, with
necessary welding at junctions and fixing the frame to wall/ ceiling/
floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including
making provision for opening for doors, windows, electrical conduits,
switch boards etc., including providing with two coats of approved steel
primer etc. complete, all as per direction of Engineer-in-charge. kg 124.25
9.155 Providing and fixing panelling or paneling and glazing in panelled or
panelled and glazed shutters for doors, windows and clerestory windows
( area of opening for panel inserts excluding portion inside grooves or
rebated to be measured). Panelling for panelled and glazed shutters
25mm to 40mm thick: Pre-laminated with decorative lamination on both
side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587 sqm 1624.05
9.156 Providing and fixing Pre -laminated medium density fibre board exterior
grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding
with screws etc. complete ( Frames, backing or studding to be paid
separately).
9.156.1 Pre-laminated with decorative lamination on both side exterior
Grade - I MDF Board 12 mm thick confirming to IS:14587 sqm 885.15
9.156.2 Pre-laminated with decorative lamination on both side exterior
Grade - I MDF Board 18 mm thick confirming to IS:14587 sqm 1080.00
9.157 Providing and fixing Pre-laminated medium density fibre board IS:
14587:1998 marked, with one side decorative lamination other side
balancing lamination Grade-I(exterior grade) in shelves with screws and
fittings wherever required, edges to be sealed with PVC edge bending
tape 2.00 mm thick of approved brand (fittings to be paid separately).
9.157.1 Pre-laminated with decorative lamination one side and other
side balancing lamination exterior Grade - I MDF Board 18
mm thick confirming to IS:14587 sqm 1207.60
9.157.2 Pre-laminated with decorative lamination one side and other
side balancing lamination exterior Grade - I MDF Board 25
mm thick confirming to IS:14587 sqm 1626.05
9.158 Providing and fixing in wall lining medium density fibre board IS:
14587:1998 marked, Pre-laminated one side decorative lamination and
other side balancing lamination, with necessary fixing arrangement and
screws etc. complete.
9.158.1 12 mm thick. sqm 1050.65
9.158.2 18 mm thick. sqm 1249.35
9.158.3 25 mm thick. sqm 1683.50
9.159 Providing and fixing 25mm thick pre-laminated medium density fibre
board exterior grade ( Grade-I) IS:14587:1998 marked with one side
decorative and other side balancing lamination for cupboard shutters
edges to be sealed with PVC edge bending tape 2.00 mm thick of
approved brand including ISI marked nickel plated bright finishing M.S.

No.
piano hinges conforming to IS:3818 marked with necessary screw etc

all complete. sqm 1816.75
9.160 Providing and fixing skirting with Pre-laminated medium density fibre
board exterior grade (Grade-I) conforming to IS: 14587:1998 marked,
with (one side decorative and other side balancing lamination and edges
to be sealed with PVC edge bending tape 2.00 mm thick of approved
brand with necessary fixing arrangements and screws, including drilling
necessary holes for rawl plugs etc. all complete.
9.160.1 18 mm thick. sqm 1843.15
9.160.2 25 mm thick. sqm 2277.30
9.161 Providing and fixing fire resistant door frame of section 50 x 60 mm on
horizontal side & 35 x 60 mm on vertical sides having built in rebate
made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/
m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters.
The frame shall be filled with Mineral wool Insulation having density min
96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos
( 5 each on vertical style & 4 on horizontal style of size M10 x 80 )
suitable for fixing in the opening along with Factory made Template for
SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated
glazed shutter . The frame shall be finished with a approved fire resistant
primer or Powder coating of not less than 30 micron in desired shade
as per the directions of Engineer - in- charge . (Cost of SS ball bearing
hinges is excluded). metre 1512.95
9.162 Providing and fixing 60 mm thick glazed fire resistant door shutters of
120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999,
tested and certified as per laboratory approved by Engineer-in-charge,
with suitable mounting on door frame, consisting of vertical styles, top
rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60
mm made out of 1.6mm thick G.I. sheet (zinc coating not less than
120gm/m²) duly filled mineral wool insulation having density min 96 kg/
m³ and fixing with necessary stainless steel ball bearing hinges of size
100x89x3mm of approved make, including applying a coat of approved
fire resistant primer or powder coating not less than 30 micron etc all
complete as per direction of Engineer-in-charge (panelling to be paid for
seperately). sqm 8379.30
9.163 Providing and fixing non load bearing fixed frame for fire resistant glazed
Partition for 120 minutes Fire Rating, made out to a profile of dimension
60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test
evidence suitable for fixing fire rated glass for 120 minutes of both integrity
& radiation control (EW120) & minimum 20 minutes of insulation
(EI20).The profile has to be fixed to the supporting construction by means
of anchor fasteners of size M10 x 80, every 150 mm from the edges and
every 500 mm (approx) c/c. Linear measurement of frame shall be
measured for payment. The frame shall be filled with mineral wool
insulation of density min 96kg/ m³ and finished with a approved fire
resistant primer or Powder coating of not less than 30 micron in desired
shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer
- in- charge. metre 1512.95

No.
9.164 Providing and fixing glazing in fire resistant door shutters, fixed panels
& partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet
(zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed
with M4 x 38 mm SS screws at distance 75 mm from the edges and
150 mm c/c , including applying a coat of approved fire resistant primer/
powder coating of not less than 30 micron on G.I. beading, & special
ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC
2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-
charge with glass of required thickness having 120 minutes of fire
resistance both integrity & radiation control (EW120) and minimum 20
minutes of insulation (EI20). The manufacturer have to give test
report/certification of fire glass and the glass should have the
stamp showing the value of E, EW & EI. The glass shall be tested
in approved NABL accredited lab or by any other accreditation
body which operates in accordance with ISO/IEC 17011 and
accredits labs as per ISO/IEC 17025 for testing and calibration
scopes shall be eligible. The maximum glazing size shall not be
more than 1100x2200 mm (w x h) or 2.42 sqm. sqm 39395.30
9.165 Providing and fixing bright /matt finished Stainless Steel handles of
approved quality & make with necessary screws etc all complete.
9.165.1 125 mm each 98.75
9.165.2 100mm each 74.00
9.165.3 75 mm each 47.20

SUB HEAD : 10.0
STEEL WORK
179
BASIC RATES (10.0 STEEL WORK)
No.
100x58x 1.90 mm 10 Nos 80.00
0973 Rolling shutter made of 80x1.25 mm machine rolled laths sqm 1400.00
0974 Top cover for rolling shutters 1.25 mm thick metre 800.00
0975 27.5 cm long wire spring grade No. 2 for rolling shutters each 300.00
0976 Ball bearing for rolling shutters each 260.00
0977 Extra for mechanical devices chain and cranked operation for
operating rolling shutters: exceeding 10.00 sqm and up to
16.80 sqm area of door sqm 800.00
0978 Extra for mechanical devices chain and cranked operation for
operating rolling shutters: exceeding 16.80 sqm area of door sqm 800.00
1009 Flats exceeding 10 mm in thickness quintal 4600.00
1010 Mild steel plates quintal 4800.00
1011 Steel glazed door, window/ ventilator, all members viz. F7D,
F4B, K11 and K12B etc. kg 54.00
1019 Mild steel hooks each 32.00
1020 Mild steel rivets quintal 5000.00
1035 Bolts and nuts above 300 mm in length quintal 5100.00
1036 Iron pintels including welded pin each 37.00
1143 Steel beading 10x10x1.6mm (box type) metre 27.00
SUB HEAD : 10.0 STEEL WORK 180

No.
1214 Welding by gas plant cm 2.00

1221 20 mm dia holding down bolts quintal 6100.00
1222 Mild steel sheets with bolts and nuts to rest on pintels each 120.00
60 mm 10 Nos 260.00
80 mm 10 Nos 300.00
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10 mm x
120 mm 10 Nos 365.00
140 mm 10 Nos 450.00
160 mm 10 Nos 575.00
4001 Stainless steel (Grade-304)hollow section round/square tubes kg 220.00
4002 Stainless steel bolts/square bar and plates kg 115.00
4006 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "B" metre 190.00
4007 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "C" metre 210.00
4008 Pressed steel door frames (mild steel sheet 1.60 mm) Profile "E" metre 240.00
4010 Mild steel tubes hot finished seamless type kg 67.00
4011 Mild steel tubes electric resistant or induction butt welded ERW kg 47.00
4012 Circular C.I. Box for ceiling fan internal dia 140 mm, 73 mm height,
toplid of 1.5mm thick MS sheet each 52.00

No.
7029 Galvanised wire mesh of average width of aperture 1.4 mm and

nominal dia of wire 0.63 mm sqm 250.00
7068 Extra for providing grilled rolling shutters with 8 mm dia M.S. rod sqm 500.00
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and
0.50mm dia wire sqm 400.00

10.0 STEEL WORK

No.
10.1 Structural steel work in single section, fixed with or without connecting
plate,including cutting, hoisting, fixing in position and applying a priming
coat of approved steel primer all complete. kg 86.05
10.2 Structural steel work riveted, bolted or welded in built up sections, trusses
and framed work, including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer all complete. kg 101.75
10.3 Providing and fixing in position collapsible steel shutters with vertical
channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm
size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia
steel pulleys, complete with bolts, nuts, locking arrangement, stoppers,
handles, including applying a priming coat of approved steel primer. sqm 8670.50
10.4 Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame
and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset
plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm
angle and T- iron guide at the top and bottom respectively, including
applying a priming coat of approved steel primer sqm 4992.05
10.5 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6
mm angle iron and 3 mm M.S. gusset plates at the junctions and corners,
all necessary fittings complete, including applying a priming coat of
approved steel primer.
10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces sqm 4428.15
10.5.2 Using flats 30x6mm for diagonal braces and central cross
piece sqm 4278.15
10.6 Supplying and fixing rolling shutters of approved make, made of required
size M.S. laths, interlocked together through their entire length and
jointed together at the end by end locks, mounted on specially designed
pipe shaft with brackets, side guides and arrangements for inside and
outside locking with push and pull operation complete, including the
cost of providing and fixing necessary 27.5 cm long wire springs
manufactured from high tensile steel wire of adequate strength
conforming to IS: 4454 - part 1 and M.S. top cover of required thickness
for rolling shutters.
10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 2944.10
10.7 Providing and fixing ball bearing for rolling shutters. each 419.85
10.8 Extra for providing mechanical device chain and crank operation for
operating rolling shutters.
10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area sqm 1106.55
10.8.2 Exceeding 16.80 sqm in area sqm 1106.55
10.9 Extra for providing grilled rolling shutters manufactured out of 8 mm dia
M.S. bar instead of laths as per design approved by Engineer-in- charge,
(area of grill to be measured). sqm 668.95

No.
10.10 Fixing standard steel glazed doors, windows and ventilators in walls,
including fixing of float glass panes with glazing clips and special metal-
sash putty of approved make, or metal beading with screws, (only steel
windows, glass panes cut to size and glazing clips or metal beading
with screws, shall be supplied by department free of cost.
10.10.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3
coarse sand : 6 graded stone aggregate 20 mm nominal size) kg 63.00
10.10.2 Fixing with carbon steel galvanised dash fastener of required
dia and size (to be paid for separately) kg 31.65
10.11 Providing and fixing factory made ISI marked steel glazed doors, windows
and ventilators, side /top /centre hung, with beading and all members
such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled
steel sections, joints mitred and flash butt welded and sash bars tenoned
and riveted, including providing and fixing of hinges, pivots, including
priming coat of approved steel primer, but excluding the cost of other
fittings, complete all as per approved design, (sectional weight of only
steel members shall be measured for payment).
coarse sand : 6 graded stone aggregate 20 mm nominal size) kg 166.50
10.12 Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm
(box type), approved shape and section with screws instead of glazing
clips and metal sash putty, in steel doors, windows, ventilators and
composite units. metre 45.40
10.13 Providing and fixing T-iron frames for doors, windows and ventilators of
mild steel Tee-sections, joints mitred and welded, including fixing of
necessary butt hinges and screws and applying a priming coat of
approved steel primer.
coarse sand : 6 graded stone aggregate 20 mm nominal size). kg 106.45
10.14 Providing and fixing pressed steel door frames conforming to IS: 4351,
manufactured from commercial mild steel sheet of 1.60 mm thickness,
including hinges, jamb, lock jamb, bead and if required angle threshold
of mild steel angle of section 50x25 mm, or base ties of 1.60 mm,
pressed mild steel welded or rigidly fixed together by mechanical means,
including M.S. pressed butt hinges 2.5 mm thick with mortar guards,
lock strike-plate and shock absorbers as specified and applying a coat
of approved steel primer after pre-treatment of the surface as directed
by Engineer-in-charge:

No.
10.14.1 Profile B
10.14.1.1 Fixing with adjustable lugs with split end tail to
each jamb metre 417.60
10.14.1.2 Fixing with carbon steel galvanised dash fastener
of required dia and size (to be paid for separately) metre 406.90
10.14.2 Profile C
10.14.3 Profile E
10.15 Providing and fixing M.S. Tubular frames for doors, windows, ventilators
and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick
M.S. Sheet, joints mitred, welded and grinded finish, with profiles of
required size, including fixing of necessary butt hinges and screws and
applying a priming coat of approved steel primer.
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) kg 137.30
10.16 Steel work in built up tubular (round, square or rectangular hollow tubes
etc.) trusses etc., including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer, including welding and
bolted with special shaped washers etc. complete.
10.16.1 Hot finished welded type tubes kg 143.45
10.16.2 Hot finished seamless type tubes kg 157.50
10.16.3 Electric resistance or induction butt welded tubes kg 129.35
10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar,
bent to shape with hooked ends in R.C.C. slabs or beams during laying,
including painting the exposed portion of loop, all as per standard design
10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for
ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5
mm thick M.S. sheet with its top surface hacked for proper bonding,
top lid shall be screwed into the cast iron/ M.S. sheet box by means of
3.3 mm dia round headed screws, one lock at the corners. Clamp shall
be made of 12 mm dia M.S. bar bent to shape as per standard drawing. each 172.25
10.19 Providing and fixing mild steel round holding down bolts with nuts and
washer plates complete. kg 83.85

No.
10.20 Providing and fixing bolts including nuts and washers complete. kg 128.45
10.21 Providing and fixing M.S. rivets of sizes in position. kg 220.40
10.22 Welding by gas or electric plant including transportation of plant at
site etc. complete. cm 3.35
10.25 Steel work welded in built up sections/ framed work, including cutting,
hoisting, fixing in position and applying a priming coat of approved steel
primer using structural steel etc. as required.
10.25.1 In stringers, treads, landings etc. of stair cases, including
use of chequered plate wherever required, all complete kg 93.65
10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates
and similar works kg 131.00
10.26 Providing and fixing hand rail of approved size by welding etc. to steel
ladder railing, balcony railing, staircase railing and similar works,
including applying priming coat of approved steel primer.
10.26.1 M.S. tube kg 145.65
10.26.2 E.R.W. tubes kg 138.15
10.26.3 G.I. pipes kg 158.00
10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron)
dash fastener of 10 mm dia double threaded 6.8 grade (yield strength
480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide
PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry,
etc. as per direction of Engineer-in-charge.
10.27.1 10 x 60 mm each 103.65
10.27.2 10 x 80 mm each 109.00
10.27.3 10 x 120 mm each 134.25
10.27.4 10 x 140 mm each 145.65
10.27.5 10 x 160 mm each 178.90
10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow
tubes, channels, plates etc., including welding, grinding, buffing, polishing
and making curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c fixing the railing
with necessary accessories & stainless steel dash fasteners , stainless
steel bolts etc., of required size, on the top of the floor or the side of
waist slab with suitable arrangement as per approval of Engineer-in-
charge, (for payment purpose only weight of stainless steel members
shall be considered excluding fixing accessories such as nuts, bolts,
fasteners etc.). kg 575.45
10.29 Providing & fixing fly proof wire gauze to windows, clerestory windows &
doors with M.S. Flat 15x3 mm and nuts & bolts complete.
10.29.1 Galvanised M.S. Wire gauze with 0.63 mm dia wire and
1.4 mm aperture on both sides sqm 709.30
10.29.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia wire
and 1.4 mm aperture on both sides sqm 929.55

No.
10.30 Providing & fixing glass panes with putty and glazing clips in steel doors,
windows, clerestory windows, all complete with :
10.30.1 4.0 mm thick glass panes sqm 900.55
10.30.2 5.5 mm thick glass panes sqm 1194.85
10.31 Providing and fixing angle iron frames for doors, windows and ventilators
of mild steel Angle sections of size 35x35x5 mm, joints mitred and
welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing
T-iron frame or to the wall with dash fastener, including fixing of necessary
butt hinges and screws and applying a priming coat of approved steel
primer, all complete as per the direction of Engineer-In-charge. kg 96.20

SUB HEAD : 11.0
FLOORING
188
BASIC RATES (SH: 11.0 FLOORING)
No.
0785 Marble chips up to 4 mm and down size White & black quintal 189.00
0788 Marble chips large size above 4 mm White & black quintal 250.00
0875 Red, chocolate, orange, buff or yellow (red oxide of iron) light
shade pigment kg 60.00
0876 Green or blue medium shade pigment kg 56.00
1149 Glass strip 4 mm thick 40 mm deep metre 20.00
SUB HEAD : 11.0 FLOORING 189

No.
1168 Kota stone slab 20 mm to 25 mm thick (semi-polished) sqm 280.00
1187 First class teak wood in scantling 10 cudm 880.00
1201 Precast terrazzo tiles 22 mm thick (light shade) sqm 285.00
1202 Precast terrazzo tiles 22 mm thick (medium shade) sqm 265.00
1203 Precast terrazzo tiles 22 mm thick (dark shade) sqm 245.00
1227 Chequered terrazzo tiles 22 mm thick (light shade) sqm 275.00
1228 Chequered terrazzo tiles 22 mm thick (medium shade) sqm 300.00
1229 Chequered terrazzo tiles 22 mm thick (dark shade) sqm 260.00
1240 18 mm thick Italian Marble stone slab, Perlato (slab area up to
0.5 sqm). sqm 3209.00
1242 Glass mossaic tiles (20 mm x 20 mm x 4 mm) sqm 2049.00
1243 Tile fixing chemical adhesive kg 8.70
1244 Cement Polymer Grout Compound kg 16.00
1245 Acid for cleaning tiles litre 18.00
2500 Extra for selected planks of second class deodar wood 10 cudm 110.00
2708 Truf Paver (500 x 500 x 40 mm) sqm 500.00
2709 Ceremic Tiles Pieces for Crazy Flooring quintal 135.00
2710 White marble makrana second quality plain veined stone pieces
for crazy flooring quintal 150.00
2711 FS800H Grade Flooring Panel (Size 600 mm x600 mm x32 mm) each 750.00

No.
2714 Zinc Electroplated Tube Stinger each 66.00
2715 Machine Screw for Fixing each 2.00
6001 White marble slab Makrana second quality plain veined
6007 Pink marble slab plain 18 mm thick sqm 645.00
6010 Udaypur green marble slab plain 18 mm thick sqm 620.00
6019 Black Zebra marble slab plain 18 mm thick sqm 900.00
7024 Acid Proof cement tonne 7800.00
7070 Chequered precast cement concrete tiles 22 mm thick using
marble chips of size 6mm - Light shade using white cement sqm 400.00
7071 White marble Raj Nagar plain 18 mm thick upto 0.50 sqm area sqm 600.00
7077 Acid and alkali resistant tiles 300x300 mm size, 10 mm thick 10 Nos 520.00
7236 Precast chequered cement tiles 22 mm thick Dark shade using
ordinary cement sqm 225.00
7237 Precast chequered cement tiles 22 mm thick medium shade
using 50% white cement 50% ordinary cement sqm 335.00
7800 Ceramic Glazed Tiles 1st quality minimum thickness 5mm in
all colours shades and designs except burgundy, bottle green,
black sqm 212.00
7801 Ceramic Glazed Tiles 1st quality 300 x 300 mm in all shades
and designs of White, Ivory, grey, Fume Red brown etc. sqm 209.10
7802 Ceramic Glazed Tiles 1st quality 300 x 300 in all shades designs
except White, Ivory, Grey, Fume Red Brown etc. sqm 260.00
7803 Rectified Ceramic Glazed Tiles 1st quality 300 x 300 mm or more
in all shades designs White, Ivory, Grey, Fume Red Brown etc. sqm 340.00
7804 Rectified Ceramic Glazed Tiles 1st quality 300 x 300 mm or more
in all shades designs except White, Ivory, Grey, Fume Red Brown
etc. sqm 400.00
7850 Agaria White marble slab plain 18 mm thick sqm 1100.00

No.
8623 Vitrified floor tile 100x100 cm conforming to IS 15622:2006

group (B1a) sqm 1390.00
8624 "Border tiles 200x75mm size each 16.00
8682 Epoxy Grout kg 371.00
8731 High polymer modified quickset tile adhesive kg 9.00

11.0 FLOORING

No.
11.1 Brick on edge flooring with bricks of class designation 7.5 on a bed of
12 mm cement mortar, including filling the joints with same mortar, with
common burnt clay non modular bricks:
11.1.1 1:4 (1 cement : 4 coarse sand) sqm 867.45
11.1.2 1:6 (1cement : 6 coarse sand) sqm 829.45
11.2 Dry brick on edge flooring in required pattern with bricks of class
designation 7.5 on a bed of 12 mm mud mortar, including filling joints
with Jamuna sand, with common burnt clay non modular bricks. sqm 680.85
11.3 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate) finished with a floating coat of neat cement, including
cement slurry, but excluding the cost of nosing of steps etc. complete.
11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 498.35
11.4 52 mm thick cement concrete flooring with concrete hardener topping,
under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12
mm thick cement hardener consisting of mix 1:2 (1 cement hardener
mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening
compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's
specifications. This includes cost of cement slurry, but excluding the
cost of nosing of steps etc. complete. sqm 787.50
11.5 62 mm thick cement concrete flooring with concrete hardener topping,
under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20mm nominal size) and top layer
12mm thick cement hardener consisting of mix 1:2 (1 cement hardener
mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening
compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s
specifications. This includes cost of cement slurry, but excluding the
cost of nosing of steps etc. complete. sqm 854.30
11.6 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1
cement : 3 coarse sand), finished with a floating coat of neat cement.
11.6.1 18 mm thick sqm 521.15
11.7 Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size), including finishing
complete. cum 7335.10
11.8 Extra for making chequers of approved pattern on cement concrete floors,
steps, landing, pavements etc. sqm 63.20
TERRAZO FLOORING
11.9 40 mm thick marble chips flooring rubbed and polished to granolithic
finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top
layer 6mm thick with white, black, chocolate, grey, yellow or green

No.
marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement

marble powder mix 3:1 (3 cement : 1 marble powder) by weight in
proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by
volume, including cement slurry etc. complete :
11.9.2 Light shade pigment with white cement sqm 877.10
11.9.3 Medium shade pigment with 50% white cement and 50%
11.9.4 White cement without any pigment sqm 855.60
11.10 40 mm thick marble chips flooring, rubbed and polished to granolithic
layer 9 mm thick with white, black, chocolate, grey, yellow or green
proportion of 4:7 (4 cement marble powder : 7 marble chips) by volume,
including cement slurry etc. complete.
11.10.1 Dark shade pigment with Ordinary cement sqm 876.90
11.11 40 mm thick marble chips flooring, rubbed and polished to granolithic
layer 12 mm thick with white, black, chocolate, grey yellow or green
proportion of 2:3 (2 cement marble powder mix : 3 marble chips) by
volume, including cement slurry etc. complete :

No.
11.12 Marble chips skirting up to 30 cm height, rubbed and polished to

granolithic finish, top layer 6 mm thick with white, black, chocolate,
grey, yellow or green marble chips of sizes from smallest to 4 mm
nominal size, laid in cement marble powder mix 3:1 (3 cement : 1
marble powder) by weight in proportion of 4:7 (4 cement marble powder
mix : 7 marble chips) by volume :
11.12.1 18 mm thick with under layer 12 mm thick in cement
plaster 1:3 (1 cement : 3 coarse sand) :
11.12.1.1 Dark shade pigment with ordinary cement sqm 1398.20
11.12.1.2 Light shade pigment with white cement sqm 1428.30
11.12.1.3 Medium shade pigment with 50% white cement
and 50% ordinary cement sqm 1409.90
11.12.1.4 White cement without any pigment sqm 1406.80
11.12.1.5 Light shade pigment with ordinary cement sqm 1394.40
11.12.1.6 Ordinary cement without any pigment sqm 1370.70
11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete
floors.
11.13.1 40 mm wide and 4 mm thick metre 75.15
11.14 Extra for laying terrazo flooring on staircase treads not exceeding 30
cm in width, including cost of forming, nosing etc. sqm 72.05
11.15 Crazy marble stone flooring, including filling the gaps with light shade
pigment with white cement marble powder mixture (3 parts of white
cement : 1 part of marble powder) by weight in proportion of 4:7 (4
cement marble powder mix : 7 white, black or white and black marble
chips of sizes from 1 mm to 4 mm nominal size by volume), with under
layer 25 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 12.5 mm nominal size), including rubbing,
polishing and cement slurry etc. complete :
11.15.1 18 mm thick crazy marble stone white, black or as specified sqm 1329.25
TILE FLOORING
11.16 Precast terrazo tiles 22 mm thick with graded marble chips of size upto
12 mm, laid in floors, and landings, jointed with neat cement slurry
mixed with pigment to match the shade of the tiles, including rubbing
and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1
cement:4 coarse sand) :
11.16.1 Light shade pigment using white cement sqm 1238.60
11.16.2 Medium shade pigment using 50% white cement and 50%
11.16.3 Dark shade pigment using ordinary cement sqm 1147.00
11.17 Extra if terrazo tiles are laid in treads of steps not exceeding 30 cm
in width. sqm 90.05

No.
11.18 Precast terrazo tiles 22 mm thick with graded marble chips of sizes
upto 12 mm, in skirting and risers of steps not exceeding 30 cm in
height, on 12 mm thick cement plaster 1:3 (1 cement : 3 coarse sand),
jointed with neat cement slurry mixed with pigment to match the shade
of the tiles, including rubbing and polishing complete with tiles of :
11.18.2 Medium shades pigment using 50% white cement and 50%
11.19 Chequered terrazo tiles 22 mm thick with graded marble chips of size
up to 6 mm in floors, jointed with neat cement slurry mixed with pigment
to match the shade of the tiles, including rubbing and polishing complete,
on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :
11.19.2 Medium shade pigment using 50% white cement, 50%
11.20 Chequerred precast cement concrete tiles 22 mm thick in footpath &
courtyard, jointed with neat cement slurry mixed with pigment to match
the shade of tiles, including rubbing and cleaning etc. complete, on 20
mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
11.20.2 Medium shade pigment using 50% white cement 50%
Grey cement sqm 1104.25
11.21 Providing and fixing 10 mm thick acid and/or alkali resistant tiles of
approved make and colour using acid and/or alkali resisting mortar
bedding, and joints filled with acid and/or alkali resisting cement as per
IS : 4457, complete as per the direction of Engineer-in- Charge.
11.21.1 In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof
cement : 4 coarse sand)
11.21.1.1 Acid and alkali resistant tile sqm 1495.00
11.21.2 In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof
cement : 4 coarse sand)
11.21.2.1 Acid and alkali resistant tile sqm 1607.70
11.22 Tile work in skirting, risers of steps and dado up to 2 m height over 12
mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and
jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in
white cement mixed with pigment of matching shade complete.
11.22.1 Marble tiles (polished) Raj Nagar
11.22.1.1 8 mm thick sqm 1239.55

No.
MARBLE STONE FLOORING

11.23 Marble stone flooring with 18 mm thick marble stone, as per sample of
marble approved by Engineer-in-charge, over 20 mm (average) thick base
of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with
grey cement slurry, including rubbing and polishing complete with :
11.23.1 Makrana white second quality sqm 3237.80
11.23.2 Raj Nagar plain sqm 1960.75
11.23.3 Agaria White sqm 2730.05
11.23.4 Black Zebra sqm 2422.30
11.23.5 Udaipur green marble sqm 1991.50
11.23.6 Pink plain marble sqm 2029.95
11.24 Extra for pre finished nosing to treads of steps of marble stone. metre 530.25
11.25 Extra for marble stone flooring in treads of steps and risers using single
length up to 2.00 metre. sqm 622.75
KOTA STONE FLOORING
11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and
jointed with grey cement slurry mixed with pigment to match the shade
of the slab, including rubbing and polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26.1 25 mm thick sqm 1531.85
11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and
pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3
coarse sand) and jointed with grey cement slurry mixed with pigment to
match the shade of the slabs, including rubbing and polishing complete. sqm 1810.05
SAND STONE FLOORING
11.28 40 mm thick fine dressed stone flooring over 20 mm (average) thick
base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished
flush.
11.29 40 mm thick fine dressed stone flooring over 20 mm (average) thick
base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing
with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of
pigment to match the shade of stone.
11.30 40 mm thick rubbed stone flooring over 20 mm (average) thick base of
cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick,
side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed
with pigment to match the shade of stone and pointing with same mortar.
11.31 Extra for pre finished nosing in treads of steps of Kota stone/ sand
stone slab. metre 148.10

No.
11.32 Extra for Kota stone/ sand stone in treads of steps and risers using
single length up to 1.05 metre. sqm 33.10
WOODEN FLOORING
11.33 25 mm wooden planking, tongued and grooved in flooring, including fixing
with iron screws complete with :
11.33.2 Second class deodar wood sqm 2759.10
11.34 38 mm thick wood block flooring of first class teak wood laid over 25
mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 10 mm nominal size) to be paid
separately, coated with a thin layer of hot bitumen penetration 80/25
(blown type) @ 2.45 kg per sqm, including fixing blocks in position after
dipping in hot bitumen (blown type) up to half depth, planed, levelled
smooth and finished complete. sqm 9971.20
11.35 Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs
of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum
three lugs to be provided), including necessary welding and applying a
priming coat of approved primer on exposed surface etc. complete. kg 132.25
CERAMIC GLAZED TILES
11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm
(thickness to be specified by the manufacturer) of 1st quality conforming
to IS : 15622 of approved make in colours such as White, Ivory, Grey,
Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :
4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including
pointing the joints with white cement and matching pigment etc.,
11.37A Providing and fixing 1st quality ceramic glazed floor tiles conforming to
IS : 15622 (thickness to be specified by the manufacturer ) of approved
make in all colours, shades except burgundy, bottle green, black of any
size as approved by Engineer-in-Charge in skirting, risers of steps and
dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm including
pointing in white cement mixed with pigment of matching shade
11.38 Providing and laying Ceramic glazed floor tiles of size 300x300 mm
(thickness to be specified by the manufacturer), of 1st quality conforming
to IS : 15622, of approved make, in all colours, shades, except White,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar
1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3
kg/ sq.m including pointing the joints with white cement and matching
pigments etc., complete. sqm 996.70
11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300
mm or more (thickness to be specified by the manufacturer), of 1st
quality conforming to IS : 15622, of approved make, in colours White,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4
(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/
sqm including grouting the joints with white cement and matching
pigments etc., complete. sqm 1088.40

No.
11.40 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300
mm or more (thickness to be specified by the manufacturer), of 1st
quality conforming to IS : 15622, of approved make, in all colours, shades,
except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement
Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry
@ 3.3 kg/ sqm including pointing the joints with white cement and
matching pigments etc., complete. sqm 1170.70
VITRIFIED FLOOR TILES
11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be
specified by the manufacturer) with water absorption less than 0.08%
and conforming to IS: 15622, of approved make, in all colours and shades,
laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),
jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the
joints with white cement and matching pigments etc., complete.
11.41.1 Size of Tile 500x500 mm sqm 1267.80
11.42 Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4
coarse sand) bedding in laying of floor tiles and jointing with grey cement
slurry @ 3.3 kg/ sqm. sqm 677.55
11.43 Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer
modified quick-set tile adhesive (Water based) conforming to IS: 15477,
in average 3mm thickness. sqm 587.20
11.44 Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar
1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including
filling the gaps with ordinary cement mixture & mixing with synthetic
polyester fibre, triangular in shape having specific gravity of 1.34 to
1.40, cross section size ranging from 10 to 40 micron & length upto 6
mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar,
including providing and mixing water proofing material in mortar @ 1 kg
per 50 kg of cement, all complete as per direction of Engineer-in-charge. sqm 735.65
11.45 Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on
150 mm thick sub grade of compacted bed of 20 mm thick nominal size
stone aggregate and base course and filling with 150 mm thick jamuna
sand, including spreading, well ramming, consolidating and finishing
smooth etc. all complete as per direction of Engineer-in-charge. sqm 1511.90
11.46 Providing and laying Vitrified tiles in different sizes (thickness to be
specified by manufacturer), with water absorption less than 0.08 % and
conforming to I.S. 15622, of approved make, in all colours & shade, in
skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/
sqm including grouting the joint with white cement & matching pigments
etc. complete.

No.

11.46A Providing and fixing glazed screen printed border tile 75mm wide having
thickness 5mm, of approved quality & make, in all shades, design and
prints, in dado, over 12mm thick bed of cement mortar 1:3 (1 Cement :
3 Coarse sand) and jointing with grey cement slurry @ 3.3 kg/sqm
including pointing with white cement mixed with pigment of matching
shade, all complete as approved by Engineer - in - Charge metre 164.65
11.47 Providing and laying Vitrified tiles in different sizes (thickness to be
specified by the manufacturer), with water absorption less than 0.08%
and conforming to IS: 15622, of approved brand & manufacturer, in all
colours and shade, in skirting, riser of steps, laid with cement based
high polymer modified quick set tile adhesive (water based) conforming
to IS: 15477, in average 6 mm thickness, including grouting of joints
(Payment for grouting of joints to be made separately).
11.48 Grouting the joints of flooring tiles having joints of 3 mm width, using
epoxy grout mix of 0.70 kg of organic coated filler of desired shade
(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /
grouting and finishing complete as per direction of Engineer-in-charge.
11.49 Providing and laying Vitrified tiles in floor with different sizes (thickness
to be specified by the manufacturer), with water absorption less than
0.08% and conforming to IS:15622, of approved brand & manufacturer,
in all colours and shade, laid with cement based high polymer modified
quick set tile adhesive (water based) conforming to IS : 15477, in average
6 mm thickness, including grouting of joints (Payment for grouting of
joints to be made separately).
11.50 Deduct for not grouting the joints with white cement and matching pigment
in the items of fixing of vitrified tiles. sqm 11.00
11.51 Providing and laying machine cut, mirror polished, Italian Marble stone
flooring laid in required pattern in linear portion of the building all complete

No.
as per architectural drawings, with 18 mm thick stone slab laid over 20

mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse
sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including
pointing with white cement slurry admixed with pigment to match the
marble shade including rubbing, curing and polishing etc. all complete
as specified and as directed by the Engineer-in-Charge.
11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona,
11.52 Providing and laying machine cut, mirror polished Marble stone flooring,
in required design (Simple geometrical, abstract etc.) and in patterns in
combination with Italian marble stones of different colours, shades and
finished surface texture etc., in linear portions of the building, all complete
as per the architectural drawings, with 18 mm thick stone slab laid over
20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse
sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including
pointing with white cement slurry admixed with pigment to match the
marble shade, including rubbing, curing and polishing etc. all complete
as specified and as directed by the Engineer-in-Charge.
11.52.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona,
11.53 Providing and fixing Glass mossaic tiles on finished plain wall surface of
size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize
design as per direction of Engineer-in- Charge. The glass mosaic tiles
to be fixed on the wall surface with the help of approved adhesive applied
at the rate of 2.5 kg per sqm and grouting of the same. The rate is
inclusive of all operation, material and required pattern approved by
Engineer-in-Charge: sqm 3250.35
11.54 Providing and fixing removable raised/false access flooring with system
and its components of approved make for different plenum height with
possible height adjustment upto 50 mm, comprising of modular load
bearing floor panels supported on G.I. rectangular stinger frame work
and G.I. Pedestal etc. all complete, as per the architectural drawings,
as specified and as directed by Engineer-in-charge consisting of:
(a) Providing at required spacing to form modular framework, pedestals
made out of GI tube of thickness minimum 2 mm and 25 mm outer
diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm
x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size
75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer
diameter with two GI Check nuts screwed on the stud for level adjustment
upto 50mm, locking and stabilizing the pedestal head in position at the
required level. The pedestals shall be fixed to the subfloor (base) through
base plate using epoxy based adhesive of approved make or the machine
screw with rawl plug.
(b) Stringers system in all steel construction hot dipped galvanized of
rectangular size 570x20x30x0.80mm thick having holes at both ends
for securing the stringers on to the pedestal head using fully threaded
screws ensuring maximum lateral stability in all directions, the grid
formed by the pedestal and stringer assembly shall receive the floor
panel, this system shall provide adequate solid, rigid support for access
floor panel, the system shall provide a minimum clear uninterrupted
clearance between the bottom of the floor for electrical conduits and

No.
wiring etc. all complete as per the architectural drawings, as specified

and as directed by the Engineer-in-charge.
(c) Providing and fixing Access Floor panel of 600x600x32 mm medium
grade Filled Steel anti static high pressure Lamination of 800H grade
(FS800H). Access Floor panel shall be steel welded construction with
an enclosed bottom pan with uniform pattern of 64 hemispherical cones.
The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7
mm fused spot welded together (minimum 64 welds in each dome and
20 welds along each flange). The panel should be Corroresist epoxy
coated for lifetime rust protection and cavity formed by the top and
bottom plate is filled with Pyrogrip noncombustible Portland cementitious
core mixed with lightweight foaming compound. The access floor shall
be factory finished with Anti-static High Pressure laminate with Non
Warp technology upto 1mm thickness for superior adhesion and Surface
flatness within 0.75mm.The panel is to withstand a Concentrated Load
of 363 kgs applied on area 25mm x 25mm without collapse in the centre
of the panel which is placed on four steel blocks. The panel will withstand
and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an
impact load of 50kg all complete as per the approved manufacturers
specification and as per the direction of Engineer-in-charge. All
specification must be printed on the side of the panel to ensure the
quality of the product.
11.54.1 300 mm Finished Floor Height (FFH) sqm 5075.30
11.54.2 450 mm Finished Floor Height (FFH). sqm 5364.30
11.55 Providing and laying flamed finish Granite stone flooring in required design
and patterns, in linear as well as curvilinear portions of the building all
complete as per the architectural drawings with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade including
rubbing, curing and polishing etc. all complete as specified and as
directed by the Engineer-in-Charge :
11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red,
Elite Brown, Cat Eye or equivalent. sqm 2476.45
11.56 Providing and laying Polished Granite stone flooring in required design
and patterns, in linear as well as curvilinear portions of the building all
complete as per the architectural drawings with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade including rubbing
, curing and polishing etc. all complete as specified and as directed by
the Engineer-in-Charge.
11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown,
Cat Eye or equivalent. sqm 3526.60
Note: Item no 11.55 & 11.56 are brought from Sub Head 8 i.e.
Cladding Work Item no 8.12 & 8.13

SUB HEAD : 12.0
ROOFING
203
BASIC RATES (SH: 12.0 ROOFING)

No.
0128 Mate day 617.00
0222 Seam bolts and nuts 6 mm dia and 25 mm long 10 Nos 10.00
0223 Fibre (reinforced by organic fibres and/or inorganic synthetic fibres)
cement corrugated sheet 6 mm thick sqm 225.00
cement close fitting adjustable ridge metre 210.00
cement corrugate serrated adjustable ridge metre 210.00
cement plain wing adjustable ridge metre 210.00
cement unserrated adjustable ridge for hips metre 210.00
cement corrugated apron piece metre 200.00
cement eaves filler piece each 175.00
cement north light curves metre 280.00
cement ventilator curves each 310.00
cement barge boards boards 6 mm thick metre 400.00
SUB HEAD : 12.0 ROOFING 204

No.
cement ridge finial pair 165.00
cement special north light curves each 555.00
cement S type louvers each 260.00
0236 Multi purpose fibre (reinforced by organic fibres and/or inorganic
synthetic fibres) cement board 6 mm thick sqm 210.00
0328 White face insulating board: 12 mm thick sqm 235.00
0332 Natural colour insulating board: 12 mm thick sqm 210.00
0336 Flame retardant face insulating board: 12 mm thick sqm 320.00
0341 Flat pressed 3 layer particle board (medium density) Grade 1,
0765 Hessian cloth sqm 35.00
0811 Mud (dry) cum 165.00
0865 Pig lead kg 130.00
0870 Plug each 10.00
0875 Red, chocolate, orange, buff or yellow (red oxide of iron) light
shade pigment kg 60.00
0886 Standard holder bat clamps for sand cast iron or cast iron pipes
0966 Sand Cast iron plain shoe 150 mm dia each 285.00
0994 Standard quality hard board sheet 3 mm thick sqm 135.00

No.
0996 Standard quality hard board sheet 4.5 mm thick sqm 210.00
head with slots 10 Nos 38.00
head with slots each 9.00
1025 Mild steel bolts 6 mm dia and 25 mm long with hexagonal head 10 Nos 10.00
1031 Galvanised steel bolts & nuts 10 mm dia and 27 cm long both
sides threaded with 4 galvanised steel nuts each 20.00
1032 Galvanised steel bolts 10 mm dia and 7 cm long with nuts each 6.00
1175 White sand stone slab 45 mm to 50 mm thick (un-dressed) sqm 240.00
1204 Precast heat resistant terrace tiles (size 300x300 mm) and
1207 G.I. Limpet washer 100 Nos 21.00
1210 G.I. plain washer thin 100 Nos 21.00
1213 Water proofing materials kg 35.00
1219 Wire nails kg 58.00
1220 Wire mesh (rabbit) sqm 42.00

No.
2308 Carriage of Plaster of paris tonne 92.24
3004 Stone ware spouts 100 mm dia 60 cm long each 40.00
3050 Galvanised steel corrugated sheets quintal 5600.00
7009 12.5 mm thick tapered edge gypsum plain borad sqm 155.00
7010 Galvanised Steel ceiling section (size 80x26x0.50 mm) metre 46.00
7011 Galvanised Steel perimetre Channel (Size 20x27x30x0.50 mm) metre 22.00
7012 Galvanised Steel intermediate Channel (Size 15x45x15x0.90 mm) metre 38.00
7013 Galvanised Steel angle hanger (Celling angle) (Size 25x10x0.50 mm) metre 12.00
7014 Galvanised Steel connecting clips (2.64 mm dia and 230 mm long
GI wire) each 4.00
7015 Galvanised Steel soffit cleat (Size 27x37x25x0.60 mm) each 3.00
7016 Joint filler kg 26.00
7017 Joint finisher kg 23.00
7028 12.5 mm thick Fully Perforated gypsum board sqm 410.00
7031 12.5 mm thick tapered edge gypsum moisture resistant board sqm 275.00
7050 PU Primer sqm 60.00
7051 40 mm (average) PU spray having 40-45 kg/m3 density sqm 400.00
7052 GI wire netting 3/4" x 24 G sqm 26.00
7053 400 G polythene sheet sqm 14.00
7090 Expanded polystyrene type N- Normal 50 mm thick sqm 125.00
7091 Expanded polystyrene type - SE 50 mm thick sqm 150.00
7187 C.I. grating 150 mm dia, weighing not less than 440 gm each 27.00
75 mm dia each 8.00

No.
7238 High Albedo paint kg 230.00
7266 Pressed clay tiles 20mm thick 250x250 mm size 1000 Nos 8600.00
7267 Plain ceiling tiles (BWP type phenol formaldehyde synthetic resin
bonded) (600x600x12 mm) each 115.00
7268 Semi perforated ceiling tiles (600x600x12 mm) each 107.00
7273 Resin Bonded Rockwool 48 kg/m3 sqm 120.00
7385 3 mm thick translucent white acrylic plastic sheet sqm 550.00
7386 12 mm thick particle board ceiling tile sqm 110.00
7857 P.T.M.T. Grating square slit 150 mm each 66.75
7904 Machine moulded common burnt clay tile bricks of class designation
12.5 1000 Nos 4900.00
8589 Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm
thick on edges sqm 685.00
8590 Galvanised Steel main Tee ceiling section Size 24x38x0.33 mm
(3 metre long) each 120.00
8591 Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm

No.
8599 GI Metal Tile Lay-in Plain Tegular edge global white color tiles of
Size 595x595 mm and 0.5 mm thick sqm 612.00
8600 GI Metal Tile Lay-in Perforated Tegular edge global white color tiles
of Size 595x595 mm and 0.5 mm thick sqm 715.00
8601 PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm
8602 Gypsum Tiles Fully Perforated Square edge of Size 595x595 mm
8667 UV stabilised 2 mm thick plain FRP sheet sqm 430.00
8668 UV stabilised 2 mm thick corrugated FRP sheet sqm 485.00
8669 Mangalore ridge tiles 20 mm thick each 8.00
8670 Mangalore tiles 20 mm thick each 8.00
8671 Precoated galvanised iron profile sheet 0.50 mm TCT sqm 350.00
8672 Precoated galvanised steel plain ridges 0.50 mm TCT and
500-600mm wide metre 210.00
8673 Precoated galvanised steel flashings/aprons 0.50 mm TCT and
upto 600mm wide metre 210.00
8675 Precoated galvanised steel north light curves metre 230.00

No.
8677 Precoated galvanised steel crimp curve sqm 230.00
8784 8 mm thick Calcium silicate perforated tiles of size 595 x595 mm sqm 833.00

12.0 ROOFING
No.
SHEET ROOFING
12.1 Providing corrugated G.S. sheet roofing including vertical / curved
surface fixed with polymer coated J or L hooks, bolts and nuts 8
mm diameter with bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead, including a coat of approved steel
primer and two coats of approved paint on overlapping of sheets
complete (up to any pitch in horizontal/ vertical or curved surfaces),
excluding the cost of purlins, rafters and trusses and including cutting
to size and shape wherever required.
12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m² sqm 1234.25
12.1.2 0.80 mm thick with zinc coating not less than 275 gm/m² sqm 1061.80
12.1.3 0.63 mm thick with zinc coating not less than 275 gm/ m² sqm 915.00
12.2 Extra for straight cutting in C.G.S. sheet roofing for making opening of
area exceeding 40 sq. decimeter for chimney stacks, sky light etc.:
12.2.1 1.00 mm thick metre 86.70
12.2.2 0.80 mm thick metre 69.35
12.2.3 0.63 mm thick metre 69.35
12.3 Extra for circular cutting in C.G.S. sheet roofing for making opening
of area exceeding 40 sq. decimeter:
12.3.1 1.00 mm thick metre 494.20
12.3.2 0.80 mm thick metre 394.75
12.3.3 0.63 mm thick metre 394.75
12.4 Providing ridges or hips of width 60 cm overall width plain G.S. sheet
fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I.
limpet and bitumen washers complete.
12.4.1 0.80 mm thick with zinc coating not less than 275 gm/m² metre 781.40
12.5 Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with
polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet
and bitumen washers complete :
12.6 Providing and fixing of 40 cm overall width plain G.S. sheet fixed
with polymer coated J or L hooks, bolts and nuts, G.l. limpet and
bitumen washer complete, bent to shape and fixed in wall with
cement mortar 1:3 (1 cement : 3 coarse sand).
12.7 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain
G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and
washers etc., including making necessary connections with rain
water pipes complete.

No.
12.8 Providing reinforced by organic fibres and/or inorganic synthetic

fibres cement 6 mm thick corrugated sheets (as per IS: 14871)
roofing up to any pitch and fixing with polymer coated J, or L hooks,
bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self
drilling fastener and EPDM washers etc. complete (excluding the
cost of purlins, rafters and trusses), including cutting sheets to size
and shape wherever required. sqm 453.25
12.9 Extra for straight cutting in reinforced by organic fibres and/or
inorganic synthetic fibres cement corrugated, semi corrugated 6
mm thick sheet roofing for making openings of area exceeding 40
square decimeter for chimney stacks, skylights etc. metre 69.35
12.10 Extra for circular cutting in reinforced by organic fibres and/or
inorganic synthetic fibres cement corrugated/ semi corrugated 6
mm thick sheet roofing for making openings of area exceeding 40
square decimeter. metre 191.60
12.11 Extra for providing and fixing wind ties of 40x 6 mm flat iron section. metre 151.10
12.12 Providing and fixing ridges and hips in fibre cement reinforced by
organic fibres and/or inorganic synthetic fibres roofing with
suitable fixing accessories or self drilling fastener and EPDM washer
etc. complete.
12.12.1 Corrugated serrated adjustable ridges metre 433.40
12.12.2 Plain wing adjustable ridges metre 433.40
12.12.3 Close fitting adjustable ridges metre 487.25
12.12.4 Unserrated adjustable hips metre 432.50
12.13 Providing and fixing fibre cement reinforced by organic fibres
and/or inorganic synthetic fibres roofing accessories in all colours
with polymer coated J or L hooks, bolts and nuts and or G.I. seam
bolts and nuts, G.I. plain and bitumen washers or with self drilling
fastener and EPDM washer etc. complete:
12.13.1 Corrugated apron pieces metre 358.75
12.13.2 Eave's filler pieces metre 290.60
12.13.3 North light curves metre 486.70
12.13.4 Ventilator curves metre 529.05
12.13.5 Barge boards metre 625.60
12.13.6 Ridge finials pair 260.65
12.13.7 Special north light curves each 871.60
12.13.8 S type louvers metre 455.00
12.14 Providing flat iron brackets 50x3 mm size with necessary bolts,
nuts and washers etc. for fixing G.S. sheets gutters with purlins. metre 70.90
12.15 Painting top of roofs with bitumen of approved quality @ 17kg per 10
sqm impregnated with a coat of coarse sand at 60 cudm per 10
sqm, including cleaning the slab surface with brushes and finally
with a piece of cloth lightly soaked in kerosene oil complete :
12.15.1 With residual type petroleum bitumen of grade VG -10 sqm 126.00

No.
12.16 10 cm thick (average) mud phaska of damped brick earth on roofs

laid to slope consolidated and plastered with 25 mm thick mud
mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping
with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks,
grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with
2% of integral water proofing compound by weight of cement and
finished neat:
12.16.1 With common burnt clay F.P.S.(non modular) brick tile of
class designation 10 sqm 826.75
12.17 10cm thick (average) mud phaska of damped brick earth on roofs
laid to slope consolidated and plastered with 25 mm thick mud
mortar with bhusha @ 35 kg per cum of earth and gobri leaping with
mix 1:1 (1 clay : 1 cow-dung) and covered with machine moulded
tile bricks, grouted with cement mortar 1:3 ( 1 cement : 3 fine sand)
mixed with 2% of integral water proofing compound by weight of
cement and finished neat.
12.17.1 With machine moulded common burnt clay F.P.S.
(non modular) brick tiles of class designation 12.5,
conforming to IS 2690 sqm 847.10
12.18 Extra for every additional 1 cm thickness of mud phaska. sqm 18.60
12.19 Providing and laying brick tiles over mumty roofs, grouted with cement
mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water
proofing compound by weight of cement, over 12 mm layer of cement
mortar 1:3 (1 cement : 3 fine sand) and finished neat:
12.19.1 With common burnt clay F.P.S. (non modular) brick tiles
of class designation 10 sqm 514.40
12.20 Providing and laying pressed clay tiles (as per approved pattern 20
mm nominal thickness of approved size) on roofs jointed with cement
mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water
proofing compound, laid over a bed of 20 mm thick cement mortar
1:4 (1 cement : 4 coarse sand) and finished neat complete. sqm 584.55
12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 stone aggregate 10 mm and down gauge), including
finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per
standard design :
12.21.1 In 75x75 mm deep chase metre 237.25
12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400
micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse
sand) and a coat of neat cement, rounding the edges and making
and finishing the outlet complete. each 244.05
12.23 Providing sand stone slab for roofing and laying them in cement
mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or
R.C.C. battens or structural steel sections (Karries or battens or
structural steel sections to be paid separately), including pointing
the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand )
complete :

No.
12.23.1 Red sand stone slab

12.23.1.1 40 to 50 mm thick sqm 793.10
12.23.2 White sand stone slab
12.23.2.1 40 to 50 mm thick sqm 815.15
CEILING
12.24 Providing and fixing insulating board ceiling of approved quality with
necessary nails etc. complete (frame work to be paid separately) :
12.24.1 Natural colour insulating board
12.24.1.1 12 mm thick sqm 733.75
12.24.2 White face insulating board
12.24.2.1 12 mm thick sqm 770.55
12.24.3 Flame retardant face insulating board
12.24.3.1 12 mm thick sqm 895.65
12.25 Providing and fixing flat pressed 3 layer medium density particle
board or graded particle board (Grade I) IS: 3087 marked, in ceiling
with necessary nails etc. complete (frame work to be paid
separately):
12.25.1 12 mm thick sqm 847.85
12.26 Providing and fixing plain multipurpose cement board(Hight pressure
steam cured) with suitable screws for cement particle board in ceiling
etc. complete (frame work to be paid seperatately).
12.26.1 6 mm thick Cement fiber board as per IS: 14862 sqm 733.05
12.26.2 6 mm thick Cement bonded wood particle board as per
IS:14276 sqm 711.00
12.27 Extra for Circular cutting including wastages in ceiling with:
12.27.1 2nd class teak wood planks 20 mm thick metre 603.05
12.27.2 Natural colour insulating board
12.27.2.1 12 mm thick metre 369.10
12.27.3 White face insulating board:
12.27.3.1 12 mm thick metre 373.70
12.27.4 Flame retardant face insulating board:
12.27.4.1 12 mm thick metre 389.25
12.27.5 Standard quality hard board sheet:
12.27.5.1 3 mm thick metre 355.30
12.27.5.2 4.5 mm thick metre 369.05
12.28 Extra for providing and fixing ceiling to curved surfaces in narrow
widths sqm 338.90

No.
12.31 Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling

up to a height of 5 m above floor level, over first class kail wood
strips 25x6 mm with 10 mm gap in between and reinforced with
rabbit wire mesh fixed to wooden frame (frame work to be paid
separately):
12.31.1 Flat surfaces sqm 1324.05
12.31.2 Curved surfaces sqm 1584.15
12.32 Extra for sunk or raised mouldings in the plaster of Paris (Gypsum
anhydrous) ceiling. sqm 445.90
12.33 Extra for providing plaster of Paris (Gypsum anhydrous) ceiling above sqm per
5 metres height from floor level. metre height 197.65
12.34 Providing fixing thermal insulation of ceiling (under deck insulation)
with Resin Bonded Fibre glass wool conforming to IS : 8183, density
24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags,
fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire
mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of
building. sqm 580.25
12.35 Providing and fixing thermal insulation with Resin Bonded Fibre glass
wool conforming to IS: 8183. Density 16 kg/m³, 50 mm thick, wrapped
in 200G Virgin Polythene bags placed over existing false ceiling
and held in position by criss-crossing GI wire. sqm 247.80
12.36 Thermal Insulation of roofing with Expanded polystyrene fixed with
suitable adhesive to the false ceiling as per the directions of the
Engineer-in-charge:
12.36.1 With Type N - Normal 50 mm thick sqm 275.10
12.36.2 With Type SE - Self Extinguishing type 50 mm thick sqm 311.85
RAIN WATER SPOUT AND PIPE
12.37 Providing and fixing 100 mm diameter and 60 cm long rain water
spout in cement mortar 1:4 (1 cement : 4 fine sand).
12.37.1 Stone ware spout each 128.40
12.38 Providing and fixing M.S. holder bat clamps of approved design to
C.I. or S.C.I. rain water pipes embedded in and including cement
concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) and cost of
cutting holes and making good the walls etc. :
12.39 Providing lead caulked joints to sand cast iron rain water pipes and
fittings:
12.39.1 100 mm dia Pipe each 421.15
12.39.2 150 mm dia Pipe each 575.95

No.
12.40 Providing, fixing and embedding sand cast iron accessories for rain
water pipes in the masonry surrounded with 12 mm thick cement
mortar of the same mix, as that of masonry (lead caulking will be
paid for separately):
12.40.1 Sand cast iron plain shoes :
12.40.1.1 150 mm diameter each 428.25
12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A, including jointing with seal
ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,
(i) Single socketed pipes.
12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/
accessories for unplasticised Rigid PVC rain water pipes conforming
to IS : 13592 Type A, including jointing with seal ring conforming to
IS : 5382, leaving 10 mm gap for thermal expansion.
12.42.1 Coupler
12.42.1.1 75 mm each 77.85
12.42.1.2 110 mm each 117.80
12.42.2 Single pushfit Coupler
12.42.2.1 75 mm each 77.85
12.42.2.2 110 mm each 108.45
12.42.3 Single tee with door
12.42.3.1 75x75x75 mm each 139.85
12.42.3.2 110x110x110 mm each 203.30
12.42.4 Single tee without door
12.42.4.1 75x75x75 mm each 122.45
12.42.4.2 110x110x110 mm each 188.55
12.42.5 Bend 87.5°
12.42.5.1 75 mm bend each 89.90
12.42.5.2 110 mm bend each 129.85
12.42.6 Shoe (Plain)
12.42.6.1 75 mm Shoe each 79.20
12.42.6.2 110 mm Shoe each 113.80
12.43 Providing and fixing unplasticised -PVC pipe clips of approved design
to unplasticised - PVC rain water pipes by means of 50x50x50 mm
hard wood plugs, screwed with M.S. screws of required length,
including cutting brick work and fixing in cement mortar 1:4 (1 cement
: 4 coarse sand) and making good the wall etc. complete.
12.43.1 75 mm each 290.15
12.43.2 110 mm each 288.80

No.
12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron
grating 15 cm diameter and weighing not less than 440 grams. each 47.25
12.45 Providing and fixing false ceiling at all height including providing and
fixing of frame work made of special sections, power pressed from
M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both
side inclusive) as per IS : 277 and consisting of angle cleats of size
25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at
1200 mm centre to centre, one flange fixed to the ceiling with dash
fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange
of cleat fixed to the angle hangers of 25x10x0.50 mm of required
length with nuts & bolts of required size and other end of angle
hanger fixed with intermediate G.I. channels 45x15x0.9 mm running
at the spacing of 1200 mm centre to centre, to which the ceiling
section 0.5 mm thick bottom wedge of 80 mm with tapered flanges
of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,
shall be fixed in a direction perpendicular to G.I. intermediate channel
with connecting clips made out of 2.64 mm dia x 230 mm long G.I.
wire at every junction, including fixing perimeter channels 0.5 mm
thick 27 mm high having flanges of 20 mm and 30 mm long, the
perimeter of ceiling fixed to wall/partition with the help of rawl plugs
at 450 mm centre, with 25mm long dry wall screws @ 230 mm
interval, including fixing of gypsum board to ceiling section and
perimeter channel with the help of dry wall screws of size 3.5 x 25
mm at 230 mm c/c, including jointing and finishing to a flush finish
of tapered and square edges of the board with recommended jointing
compound , jointing tapes , finishing with jointing compound in 3
layers covering upto 150 mm on both sides of joint and two coats of
primer suitable for board, all as per manufacturer's specification and
also including the cost of making openings for light fittings, grills,
diffusers, cutouts made with frame of perimeter channels suitably
fixed, all complete as per drawings, specification and direction of
the Engineer in Charge but excluding the cost of painting with :
12.45.1 12.5 mm thick tapered edge gypsum plain board
conforming to IS: 2095- (Part I) : 2011 (Board with BIS
certification marks) sqm 1117.65
12.45.2 12.5 mm thick tapered edge Glass Reinforced Gypsum
(GRG) board conforming to IS: 2095- (Part 3) : 1996
(Board with BIS certification marks) sqm 1237.05
12.45.3 12.5 mm thick tapered edge gypsum moisture resistant
board sqm 1286.20
12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x
2400x12.5 mm having approx. 15 % perforated area with
perforation size and pattern as approved by the Engineer-
in-charge and as per manufacturer's specification, with
all 4 side tapered and backed by acoustical tissue with
NRC value not less than 0.60 sqm 1475.85
12.46 Providing and fixing to the inlet mouth of rain water pipe PTMT (an
Engineering Thermoplastic) grating square (Slit) 150 mm square
with a height of 8 mm and weighing not less than 100 gms. each 100.45

No.
12.47 Providing & fixing UV stabilised fiberglass reinforced plastic sheet

roofing up to any pitch, including fixing with polymer coated 'J' or 'L'
hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete
but excluding the cost of purlins, rafters, trusses etc. The sheets
shall be manufactured out of 2400 TEX panel rovigs incorporating
minimum 0.3% ultra-violet stabiliser in resin system under
approximately 2400 psi and hot cured. They shall be of uniform
pigmentation and thickness without air pockets and shall conform
to IS 10192 and IS 12866.The sheets shall be opaque or translucent,
clear or pigmented, textured or smooth as specified.
12.47.1 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down
(2" or 3" or 6" ) as specified sqm 1095.20
12.47.2 2 mm thick flat sqm 999.35
12.48 Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm
nominal thickness and of approved size and as per approved pattern
on steel frame work complete (steel frame work to be paid
separately). sqm 324.40
12.49 Providing & laying on roof pressed clay tile ridge (Mangalore tile) of
20mm thickness and of approved pattern on steel frame work
complete (steel frame work to be paid separately). sqm 72.20
12.50 Providing and fixing precoated galvanised iron profile sheets (size,
shape and pitch of corrugation as approved by Engineer-in-charge)
0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120
grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns
epoxy primer on both side of the sheet and polyester top coat 15-18
microns. Sheet should have protective guard film of 25 microns
minimum to avoid scratches during transportation and should be
supplied in single length upto 12 metre or as desired by Engineer-
in-charge. The sheet shall be fixed using self drilling /self tapping
screws of size (5.5x 55 mm) with EPDM seal, complete upto any
pitch in horizontal/ vertical or curved surfaces, excluding the cost of
purlins, rafters and trusses and including cutting to size and shape
wherever required. sqm 627.55
12.51 Providing and fixing precoated galvanised steel sheet roofing accessories
0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams
per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy
primer on both side of the sheet and polyester top coat 15-18 microns
using self drilling/ self tapping screws complete :
12.51.1 Ridges plain (500 - 600mm) metre 416.30
12.51.2 Flashings/ Aprons.( Upto 600 mm) metre 368.60
12.51.3 North light curves metre 443.05
12.51.4 Barge board (Upto 300 mm) metre 355.80
12.51.5 Crimp curve sqm 408.95
12.51.6 Gutter (600 mm over all girth) metre 1041.75

No.
12.52 Providing and fixing tiled false ceiling of specified materials of size
595x595 mm in true horizontal level, suspended on inter locking
metal grid of hot dipped galvanized steel sections ( galvanized @
120 grams/ sqm, both side inclusive) consisting of main "T" runner
with suitably spaced joints to get required length and of size 24x38
mm made from 0.30 mm thick (minimum) sheet, spaced at 1200
mm center to center and cross "T" of size 24x25 mm made of 0.30
mm thick (minimum) sheet, 1200 mm long spaced between main
"T" at 600 mm center to center to form a grid of 1200x600 mm and
secondary cross "T" of length 600 mm and size 24x25 mm made of
0.30 mm thick (minimum) sheet to be interlocked at middle of the
1200x600 mm panel to form grids of 600x600 mm and wall angle of
size 24x24x0.3 mm and laying false ceiling tiles of approved texture
in the grid including, required cutting/making, opening for services
like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main
"T" runners to be suspended from ceiling using GI slotted cleats of
size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50
mm long dash fasteners, 4 mm GI adjustable rods with galvanised
butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm
center to center along main T, bottom exposed width of 24 mm of all
T-sections shall be pre-painted with polyester paint, all complete for
all heights as per specifications, drawings and as directed by
Engineer-in-charge.
12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white
color tiles of size 595x595 mm, and 0.5 mm thick with 8
mm drop; made of G I sheet having galvanizing of 100
gms/sqm (both sides inclusive) and electro statically
polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending. sqm 1504.45
12.52.2 GI Metal Ceiling Lay in perforated Tegular edge global
white color tiles of size 595x595 mm and 0.5 mm thick
with 8 mm drop; made of GI sheet having galvanizing of
100 gms/sqm (both sides inclusive) and 20% perforation
area with 1.8 mm dia holes and having NRC (Noise
Reduction Coefficient ) of 0.5, electro statically polyester
powder coated of thickness 60 microns (minimum),
including factory painted after bending and perforation,
and backed with a black Glass fiber acoustical fleece. sqm 1649.15
12.52.3 12.5 mm thick square edge PVC Laminated Gypsum
Tile of size 595x595 mm, made of Gypsum plasterboard,
manufactured from natural gypsum as per IS 2095 part I
and laminated with white 0.16mm thick fire retardant
PVC film on the face side and 12micron metalized
polyester on the back side with all edges sealed with
the face side PVC film which goes around and wraps
the edges and is bonded to the edges and the back side
metalized polyester film so as to make the tile a
completely sealed unit. sqm 1880.95

No.
12.52.4 12.5 mm thick fully Perforated Gypsum Board tile made

from plasterboard having glass fibre conforming to IS:
2095 part I, of size 595x595 mm, having perforation of
9.7x9.7 mm at 19.4 mm c/c with center borders of 48
mm and the side borders of 30 mm, backed with non
woven tissue on the back side, having an NRC (Noise
Reduction Coefficient) of 0.79, with 50 mm resin bonded
glass wool backing. sqm 1171.50
12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly
light weight calcium silicate false ceiling tiles of approved texture of
size 595 x 595 mm in true horizontal level, suspended on inter
locking metal grid of hot dipped galvanised steel sections (galvanising
@ 120 grams per sqm including both side) consisting of main ‘T’
runner suitably spaced at joints to get required length and of size
24x38 mm made from 0.33 mm thick (minimum) sheet, spaced
1200 mm centre to centre, and cross “T” of size 24x28 mm made
out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between
main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm
and secondary cross ‘T’ of length 600 mm and size 24 x28 mm
made of 0.33 mm thick (Minimum) sheet to be inter locked at middle
of the 1200x 600 mm panel to from grid of size 600x600 mm, resting
on periphery walls /partitions on a Perimeter wall angle pre-coated
steel of size(24x24X3000 mm made of 0.40 mm thick (minimum)
sheet with the help of rawl plugs at 450 mm centre to centre with 25
mm long dry wall screws @ 230 mm interval and laying 15 mm
thick densified edges calicum silicate ceiling tiles of approved texture
in the grid, including, cutting/ making opening for services like
diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever
required. Main ‘T’ runners to be suspended from ceiling using G.I.
slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm
dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with
galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at
1200 mm centre to centre along main ‘T’, bottom exposed with 24
mm of all Tsections shall be pre-painted with polyster baked paint,
for all heights, as per specifications, drawings and as directed by
Engineer-in-Charge. sqm 1643.95
Note :- Only calcium silicate false ceiling area will be measured
from wall to wall. No deduction shall be made for exposed frames/
opening (cut outs) having area less than 0.30 sqm.The calcium
silicate ceiling tile shall have NRC value of 0.50 (Minimum), light
reflection > 85%, noncombustible as per B.S. 476 part IV, 100%
humidity resistance and also having thermal conductivity <0.043 w/
mK.
12.54 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm
module which includes providing and fixing 'C' wall angle of size
20x30x20 mm made of 0.5 mm thick pre painted steel along the
perimeter of the room with help of nylon sleeves and wooden screws
at 300 mm center to centre, suspending the main C carrier of size
10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with
help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm

No.
and C carrier suspension clip and main carrier bracket at 1000 mm

c/c. Inverted triangle shaped Spring Tee having height of 24 mm and
width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the
main C carrier and in direction perpendicular to it at 600 mm centers
with help of suspension brackets. Wherever the main C carrier and
spring T have to join, C carrier and spring T connectors have to be
used. All sections to be galvanized @ 120 gms/sqm (both side
inclusive), fixing with clip in tiles into spring T with :
12.54.1 GI Metal Ceiling Clip in plain Beveled edge global white
color tiles of size 600x600 and 0.5 mm thick with 25
mm height, made of G I sheet having galvanizing of 100
gms/ sqm (both sides inclusive) and electro statically
polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending. sqm 1734.10
12.54.2 GI Metal Ceiling Clip in plain Beveled edge global white
color tiles of size 600x600 and 0.5 mm thick with 25
mm height, made of G I sheet having galvanizing of 100
gms/ sqm (both sides inclusive) and 20% perforation
area with 1.8 mm dia holes and having NRC of 0.5, electro
statically polyester powder coated of thickness
60 microns (minimum), including factory painted after
bending and perforation. sqm 1881.60
12.55 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300
mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection
> 0.70 and initial emittance > 0.75 on waterproof and sloped surface
of terrace, laid on 20 mm thick cement sand mortar in the ratio of
1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of
white cement & marble powder in ratio of 1:1, including rubbing and
polishing of the surface upto 3 cuts complete, including providing
skirting upto 150 mm height along the parapet walls in the same
manner. sqm 1374.10
12.56 Providing and laying roof insulation with 40 mm thick impervious
sprayed, closed cell free Rigid Polyurethane foam over deck insulation
conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/
cum), over a coat of polyurethane primer applied @ 6-8 sqm per
litre, laying 400 G polythene sheet over PUF spray and providing a
wearing course of 40 mm thick cement screed 1:2:4 (1 cement : 2
coarse sand : 4 stone aggregate 20 mm nominal size) in chequered
rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G
wire netting and sealing the joints with polymerized mastic, all
complete as per direction of Engineer-in-Charge. sqm 1412.20
12.57 Providing and fixing thermal insulation with Resin Bonded Fibre glass
wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick,
wrapped in 200G Virgin Polythene Bags fixed to wall with screw,
rawel plug & washers and held in position by criss crossing GI wire
etc. complete as per directions of Engineer-in-Charge. sqm 316.40

No.
12.58 Providing and fixing tiled false ceiling of specified materials of size
595x595 mm in true horizontal level, suspended on interlocking metal
grid of hot dipped galvanized steel sections ( galvanized @ 120
grams/ sqm, both side inclusive) consisting of main "T" runner with
suitably spaced joints to get required length and of size 24x38 mm
made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm
center to center and cross "T" of size 24x25 mm made of 0.30 mm
thick (minimum) sheet, 1200 mm long spaced between main "T" at
600 mm center to center to form a grid of 1200x600 mm and secondary
cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm
thick (minimum) sheet to be interlocked at middle of the 1200x600
mm panel to form grids of 600x600 mm and wall angle of size
24x24x0.3 mm and laying false ceiling tiles of approved texture in
the grid including, required cutting/making, opening for services like
diffusers, grills, light fittings, fixtures, smoke detectors etc. Main
"T" runners to be suspended from ceiling using GI slotted cleats of
size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50
mm long dash fasteners, 4 mm GI adjustable rods with galvanized
butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm
center to center along main T, bottom exposed width of 24 mm of all
T-sections shall be pre-painted with polyester paint, all complete for
all heights as per specifications, drawings and as directed by
Engineer-in-charge.
12.58.1 8 mm thick fully perforated calcium silicate board made
with Calcareous & Siliceous materials reinforced with
cellulose fiber manufactured through autoclaving process
to give stable crystalline structure with minimum
compressive strength 225 kg/ sq. cm, bending strength
100 kg/sq. cm , of size 595x595 mm, having perforation
of dia. 10 mm with minimum perforated area 18 % with
non woven tissue on the back side, having an NRC
( Noise Reduction Coefficient) of 0.85, with 50 mm thick
rockwool of 48 kg /cum backing. sqm 1759.75
12.59 Providing & fixing false ceiling at all height including providing &
fixing of framework made of special section, power pressed from
M.S. sheets and galvanised with zinc coating of 120 gms/ sqm
(both side inclusive) as per IS : 277 and consisting of angle cleat of
size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at
1200mm c/c, one flange fixed to the ceiling with dash fastener
12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat
fixed to the angle hangers of 25 x10 x0.50mm of required length
with nuts & bolts of required size and other end of angle hanger
fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the
spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick
bottom wedge of 80mm with tapered flanges of 26 mm each having
lips of 10.5mm, at 450mm c/c, shall be fixed in a direction
perpendicular to G.I intermediate channel with connecting clip made
out of 2.64mm dia x 230mm long G.I wire at every junction, including
fixing perimeter channels 0.50mm thick 27mm high having flanges
of 20mm and 30mm long, the perimeter of ceiling fixed to wall/
partitions with the help of Rawl plugs at 450mm centre, with 25mm

No.
long dry wall screws @ 230mm interval, including fixing of Calcium

Silicate Board to ceiling section and perimeter channels with the
help of dry wall screws of size 3.5 x25mm at 230mm c/c, including
jointing & finishing to a flush finish of tapered and square edges of
the board with recommended jointing compounds, jointing
tapes,finishing with jointing compounds in three layers covering up
to 150mm on both sides of joints and two coats of primer suitable
for boards, all as per manufacture's specification and also including
the cost of making opening for light fittings, grills, diffusers, cut outs
made with frame of perimeter channels suitably fixed, all complete
as per drawings, specificaton and direction of the Engineer in charge
but excluding the cost of painting with:
12.59.1 8 mm thick Calcium Silicate Board made with Calcareous
& Siliceous materials reinforced with cellulose fiber
manufactured through autoclaving process. sqm 1273.05
12.60 Providing and fixing thermal insulation of ceiling (under deck
insulation) with Resin Bonded Rockwool conforming to IS:
8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin
Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm)
@ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top
most ceiling of building. sqm 546.40
12.61 Providing and fixing thermal insulation with Resin bonded rock wool
conforming to IS: 8183, density 48 kg/m3, 50 mm thick, wrapped in
200 G virgin Polythene bags placed over existing false ceilng and
held in position by criss-crossing Gl wire. sqm 277.20
12.62 Providing and fixing thermal insulation with Resin Bonded rock wool
conforming to IS: 8183, having density 48 kg/m3,50 mm
thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with
screw, rawel plug & washers and held and in position by criss
cossing GI wire etc. complete as per directions of Engineer-in-
Charge. sqm 282.55
12.63 Providing and applying two coats of High Albedo paint having
minimum Solar Reflective Index (SRI) 108 (with solar reflectance &
thermal emittance tested as per ASTM) C 1549 and ASTM C 1371
respectively), VOC less than 10 cc/gm. The coating thickness and
the methodology of application shall strctly as per manufacturer's
specifications and as approved by Engineer-in-Charge. Surface
preparation includes cleaning with metal wire brush to remove all
dust, fungus etc., washing with water all complete. The contractor
shall give guarantee for the perfomance of SRI and also the durabitity
of coating, all complete as per direction of Engineer-in-Charge. sqm 314.85

DSR 2018 PDF

Uploaded by

Copyright:

Available Formats

DSR 2018 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DSR 2018 PDF

Uploaded by

Copyright:

Available Formats

Hkkjr ljdkj

egkfuns”kd] ds-yks-fu-fo-] ubZ fnYyh ds izkf/kdkj ds v/khu izdkf”kr

A GOVERNMENT OF INDIA PUBLICATION

JAIN BOOK AGENCY JAIN BOOK DEPOT

JAIN BOOK AGENCY (SOUTHEND) JAIN BOOK AGENCY (GURGAON)

JAIN BOOK AGENCY (INTERNATIONAL) JAIN BOOK AGENCY (GREATER NOIDA)

Place: New Delhi (PRABHAKAR SINGH)

6. Following are the Salient Features of DSR- 2018:

6.1 DSR-2018 is bilingual and in two volumes.

Salient Modifications and Changes in Sub Heads:

8.0 New Technologies and Materials

8.4 GFRG items (item no.26.51 to 26.61)

8.5 Speed floor system (Item no.26.62 to 26.64).

8.9 Prefab/Precast technology (Item no.26.73 to 26.80)

8.10 Scaffolding net (Item no. 26.81)

And suggestions for improvement are always welcome.

0.1 HIRE CHARGES OF PLANTS & MACHINERY 2

0.4 CARRIAGE CODES 61

5. Reinforced Cement Concrete 90

6. Masonry Work 105

7. Stone Work 113

8. Cladding Work 120

9. Wood and PVC Work 130

10. Steel Work 179

11. Flooring 188

12. Roofing 203

14 Repairs to Building 240

15 Dismantling and Demolishing 256

16 Road Work 264

17 Sanitary Installations 289

18 Water Supply 314

20 Pile work 371

21 Aluminium Work 378

22 Water Proofing 385

23 Rain Water Harvesting & Tubewells 394

24 Conservation of Heritage Buildings. 400

25 Structural Glazing Aluminium Composite Panel 404

26 New Technologies and Materials 411

C. CEMENT CONSUMPTION STATEMENT 444

D. BITUMEN CONSUMPTION STATEMENT 479

Note: For Sub Heads 1 to 12 refer to Vol. 1

Code Description Unit Rate

SUB HEAD : 13.0 FINISHING 225

0821 Distemper primer litre 70.00

SUB HEAD : 13.0 FINISHING 226

SUB HEAD : 13.0 FINISHING 227

SUB HEAD : 13.0 FINISHING 228

13.10 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a

SUB HEAD : 13.0 FINISHING 229

13.23 Extra for plastering on circular work not exceeding 6 m in radius:

SUB HEAD : 13.0 FINISHING 230

POINTING ON STONE WORK

SUB HEAD : 13.0 FINISHING 231

SUB HEAD : 13.0 FINISHING 232

SUB HEAD : 13.0 FINISHING 233

13.62 Painting with synthetic enamel paint of approved brand and

SUB HEAD : 13.0 FINISHING 234

SUB HEAD : 13.0 FINISHING 235

SUB HEAD : 13.0 FINISHING 236