APPROVED 19/Jul/2019 16:50:06 GMT

8 7 6 5 4 3 2 1
CUSTOMER CONNECTIONS REVISIONS
NOTES: ZONE REV ECN DESCRIPTION DATE DRAWN APPROVED
ITEM QTY DESCRIPTION COMMENTS A 1361664 ORIGINAL RELEASE 2019JUN24 E.EDWARDS A.SCHREIBER
1. WEIGHT OF HEAVIEST COMPONENT 2,000 KGS. (4,400 LBS) MOTOR 8"-150# ANSI FF FLANGE
MAXIMUM WEIGHT OF UNIT 8,591 KGS (18,900 LBS). A 1 AIR INLET GUIDE VALVE
(8) M20 X 2.5 X 55MM LNG CAPSCREWS ON 11.75" BC
2. LIFTING HOLE / FORK SLOT. B 1 AIR DISCHARGE
6"-150# ANSI FF FLANGE
(8) M20 X 150MM STUDS ON 9.50" BC
3. COMPONENT LIFTING LUG ONLY.
4"-150# ANSI FF FLANGE
C 1 AIR BYPASS
4. SEE INSTALLATION AND PRESTART MANUAL FOR INFORMATION ON PIPING, (4) M16 X 260MM STUDS ON 7.50" BC
D FOUNDATION, LUBRICATION, AND ALIGNMENT. 4"-150# ANSI RF FLANGE D
D 1 AIR COOLER WATER INLET DRIVER END
(8) .75 DIA HOLES ON 7.50" BC
5. INLET PIPING SHOULD BE NON-FERROUS AND FLANGED FOR CLEANING AND
INSPECTION. A MINIMUM OF (4) PIPE DIAMETERS OF STRAIGHT RUN IS E 1 AIR COOLER WATER OUTLET
4"-150# ANSI RF FLANGE
RECOMMENDED. USE PROPER SIZE PIPE AND SUPPORTS TO KEEP PIPE (8) .75 DIA HOLES ON 7.50" BC 2X 1415.0
STRAIN BELOW THE VALUES LISTED IN THE INSTALLATION MANUAL. [55.71]
H 1 PRELUBE PUMP SEE WIRING SCHEMATIC
J 1 MAIN DRIVER CONDUIT BOX - (SEE MOTOR OUTLINE) 1113.9
6. ALL FLANGE HOLES STRADDLE CENTER LINE.
[43.85]
L 2 VENT VALVE .25 NPT
7. COUPLING BETWEEN COMPRESSOR AND DRIVER SUPPLIED BY IR. 609.6
M 1 CONTROL PANEL
DISTANCE BETWEEN SHAFTS 3,0 [0.12]. [24.00]
N 2 CONDENSATE TRAP .50 NPT
508.0
8. DRIVER ROTATION IS COUNTER-CLOCKWISE AS VIEWED FROM P 2 CONDENSATE DRAIN VALVE .50 NPT [20.00]
THE SHAFT END OF DRIVER. R 1 LUBE OIL HEATER SEE WIRING SCHEMATIC 304.8
9. ALL CONTROL PANEL CONNECTIONS ARE THROUGH S 1 OIL RESERVOIR DRAIN 1.00 NPT PIPE PLUG [12.00]
THE BOTTOM OF THE CONTROL PANEL. T 1 IA (INSTRUMENT AIR) .50 NPT 50.8
[2.00]
U 1 CA (CONTROL AIR) .50 NPT
330.2
[13.00]

C 2221.8 6X 25.4 C
[87.47] [1.00]

2056.7
[80.97]
END OF BULLGEAR SHAFT
1371.0
3817.9 [53.98]
[150.31]
1341.0
1515.1 [52.80] 2X 280.0
[59.65] END OF [11.02]
BULLGEAR SHAFT
872.8
[34.36]
30.0
[1.18]
301.1
939.8 [11.85]
[37.00] 707.5 OF COMPRESSOR
1430.0 [27.85]
[56.30]
B 914.4 B
1404.6 [36.00]
2X 49.3
[55.30] [1.94]
2309.1
[90.91]

4X 15.7
[0.62]
969.3
[38.16]
OF
COMPRESSOR 425.5
397.5 [16.75]
[15.65] 685.8 2X 82.6
[27.00] [3.25]
850.9
[33.50]

SEE NOTE 9 SEE NOTE 2

COMPRESSOR END
1091.1 872.8 BASEPLAE CONTACT SURFACE
[42.96] [34.36] (TOP VIEW)
A A
GENERAL ARRANGEMENT WARNING: THE EXPORT OR REEXPORT OF THIS DRAWING OR A PRODUCT PRODUCED DO NOT SCALE DRAWING
LEFT VIEW TOLERANCES BY THIS DRAWING IS SUBJECT TO U.S. EXPORT ADMINISTRATION REGULATIONS
AND OTHER APPLICABLE GOVERNMENT RESTRICTIONS OR REGULATIONS. DRAWING CONFORMS TO THIRD ANGLE PROJECTION
ALL DIMENSIONS ARE IN PROPRIETARY NOTICE ASME Y14.5M - 1994 DRAWN DATE
MILLIMETERS THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET CAD GENERATED DRAWING, E.EDWARDS 2019JUN24
R

[INCHES (IF SHOWN)] INFORMATION, IS THE PROPERTY OF INGERSOLL-RAND CO., AND IS NO MANUAL REVISIONS ALLOWED CHECKED DATE NAME
GIVEN TO THE RECEIVER IN CONFIDENCE. THE RECEIVER BY RECEPTION
GENERAL ARRANGEMENT
A.SCHREIBER 2019JUN27
UNSPECIFIED TOLERANCES: AND RETENTION OF THE DRAWING ACCEPTS THE DRAWING IN CONFIDENCE UNLESS OTHERWISE SPECIFIED:
AND AGREES THAT, EXCEPT AS AUTHORIZED IN WRITING BY APPROVED DATE
- REMOVE ALL BURRS AND SHARP CORNERS
INGERSOLL-RAND CO. IT WILL (1) NOT USE THE DRAWING OR ANY COPY - WELD SYMBOLS TO BE IN ACCORDANCE C.HAYES 2019JUN27
THEREOF OR THE CONFIDENTIAL OR TRADE SECRET INFORMATION WITH ANSI/AWS A2.4
WHOLE : 13.0[.50] DRAWING TYPE
GENERAL ARRANGEMENT

THEREIN; (2) NOT COPY THE DRAWING; (3) NOT DISCLOSE TO OTHERS SIZE ESTIMATED WEIGHT DWG NO. REVISION
.X : 6.0[.25]
47672326 001
Detail Drawing
A1 A
EITHER THE DRAWING OR THE CONFIDENTIAL OR TRADE SECRET (KG UNLESS OTHERWISE SPECIFIED)
ANGLES : 1 INFORMATION THEREIN; AND (4) UPON COMPLETION OF THE NEED TO COPYRIGHT @ 2019 NOMENCLATURE
RETAIN THE DRAWING, OR UPON DEMAND, RETURN THE DRAWING, ALL Ingersoll Rand SEE NOTES 47672326001

PART NO.

Ingersoll-Rand Industrial Technologies

COPIES THEREOF, AND ALL MATERIAL COPIED THEREFROM. ALL RIGHTS RESERVED SCALE
0.06 MODEL C700 SHEET
1 OF 2
For Internal Use : Model = 47672326001 | ASSEM | A.1 | Charles Edwards | 18-Jul-19 09:58:53 AM | Design Drawing = 47672326001 | DRAW | A.4 | Charles Edwards | 18-Jul-19 09:58:53 AM | Design

8 7 6 5 4 3 2 1
18-Jul-2019 09:59:36 (model A.1/A.4)
UNLESS OTHERWISE SPECIFIED PRINTED DOCUMENT IS UNCONTROLLED A.4
 APPROVED 19/Jul/2019 16:50:06 GMT

8 7 6 5 4 3 2 1

SEE NOTE 3
TYP

R T U M 838,2 [33.00]
DOOR SWING RADIUS

3.0 [0.12]
D BETWEEN SHAFTS D

RIGHT VIEW
1251.2
OF COMPRESSOR [49.26]

2305.3
[90.76]

C C
919.6 [36.20]
SEE NOTE 2 B, C J
END OF
BULLGEAR
FRONT VIEW SHAFT

TOP VIEW
317.5
[12.50]
124.0 END OF
[4.88] BULLGEAR SHAFT
149.4 1932.3 [76.07]
B [5.88] C A

B B

OF COMPRESSOR

1819.8
1724.1
[71.65]
[67.88]

797.9
[31.41]
380.4
[14.98]

132.6 2X N D E S H
317.5 [12.50] 324.1 [12.76] 60.0
[5.22] 187.3
P P [2.36]
143.5 [7.37]
163.7 [6.44] 478.0 [18.82]
[5.65]
N N 2X P 753.9 A
A
768.7 [29.68]
OF COMPRESSOR [30.26]
RIGHT VIEW
D, E 995.9
[39.21]

FRONT VIEW 1608.2 PROPRIETARY NOTICE NAME

[63.31] THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET

INFORMATION, IS THE PROPERTY OF INGERSOLL-RAND CO., AND
IS GIVEN TO THE RECEIVER IN CONFIDENCE. THE RECEIVER BY
GENERAL ARRANGEMENT GENERAL ARRANGEMENT

RECEPTION AND RETENTION OF THE DRAWING ACCEPTS THE

DRAWING IN CONFIDENCE AND AGREES THAT, EXCEPT AS
1917.8 AUTHORIZE D IN WRITING BY INGERSOLL-RAND CO. IT WILL (1)
SIZE DWG NO. REVISION

47672326 001 A
NOT USE THE DRAWING OR ANY COPY THEREOF OR THE

[75.50] A1
CONFIDENTIAL OR TRADE SECRET INFORMATION THEREIN; (2) NOT
COPY THE DRAWING; (3) NOT DISCLOSE TO OTHERS EITHER THE
DRAWING OR THE CONFIDENTIAL OR TRADESECRET INFORMATION
PART NO.
47672326001

THEREIN; AND (4) UPON COMPLETION OF THE NEED TO RETAIN

THE DRAWING, OR UPON DEMAND, RETURN THE DRAWING, ALL SCALE NOMENCLATURE
COPIES THEREOF, AND ALL MATERIAL COPIED THEREFROM. 0.06 SHEET 2 OF 2

8 7 6 5 4 3 2 1
18-Jul-2019 09:59:36 (model A.1/A.4)
UNLESS OTHERWISE SPECIFIED PRINTED DOCUMENT IS UNCONTROLLED A.4