Scribd Logo
Upload

Welcome to Scribd!

  • 142 views

    1 CWSJVZ Attachment en ENU

    Uploaded by

    prudhvi raju
    The document describes an error that occurred due to incorrect parameters being set in an OB100/FB1 call. The parameters MCP1StatSend and MCP1StatRec were configured beyond their maximum allowed values for the PLC being used, causing an access error alarm. The solution is to configure those parameters to be less than or equal to A124 for a PLC 315 or A252 for a PLC 317.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    1 CWSJVZ Attachment en ENU

    Uploaded by

    prudhvi raju
    142 views1 page
    The document describes an error that occurred due to incorrect parameters being set in an OB100/FB1 call. The parameters MCP1StatSend and MCP1StatRec were configured beyond their maximum allowed values for the PLC being used, causing an access error alarm. The solution is to configure those parameters to be less than or equal to A124 for a PLC 315 or A252 for a PLC 317.

    Original Description:

    vxcv

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an error that occurred due to incorrect parameters being set in an OB100/FB1 call. The parameters MCP1StatSend and MCP1StatRec were configured beyond their maximum allowed values for the PLC being used, causing an access error alarm. The solution is to configure those parameters to be less than or equal to A124 for a PLC 315 or A252 for a PLC 317.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    142 views1 page

    1 CWSJVZ Attachment en ENU

    Uploaded by

    prudhvi raju
    The document describes an error that occurred due to incorrect parameters being set in an OB100/FB1 call. The parameters MCP1StatSend and MCP1StatRec were configured beyond their maximum allowed values for the PLC being used, causing an access error alarm. The solution is to configure those parameters to be less than or equal to A124 for a PLC 315 or A252 for a PLC 317.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Reason:

    Incorrect parameters set in OB100/FB1


    CALL "RUN_UP" , "gp_par"
    MCPNum :=1
    MCP1In : = P#E 16.0
    MCP1Out : = P#A 16.0
    MCP1StatSend : = P#A 400.0
    MCP1StatRec : = P#A 404.0
    Parameters MCP1StatSend and MCP1StatRec = max. A 124/ A 252 for PLC 315/317!

    System response:
    Diagnostic buffer of the PLC module, e.g. PLC 317-2DP 2AJ10:

    Order number / designation Component Edition


    6FC5 317-2AJ10-1AB0 Hardware 2218 20.71.30 06.02.2006
    Firmware V 2.1.8
    Module rack: 0
    Slot: 2
    Event 1 of 100: Event ID 16# 457F
    STOP due to STOP command
    Interruption point within the user program: Cyclic program (OB 1)
    Priority class: 1
    FB number: 15
    Block address: 2
    Existing operating status: RUN
    Requested operating status: STOP (internal)
    Internal error, incoming event
    18:24:42:984 05.01.94

    No entry made in the text database. Hex values are displayed.


    Event ID: 16# A128
    OB: 16# 01
    PK: 16# 01
    DatID 1/ 2: 16# 50 C0
    Additional information 1 / 2 / 3: 16# 0002 0000 0043
    Incoming event
    18:24:42:980 05.01.94

    Diagnostic buffer decoding leads to the following alarm:


    Event ID: 16# A128 ==> A=Alarm, 1= incoming 28Hex =40dec
    Additional information 1 / 2 / 3: 16# 0002 0000 0043 ==>
    02Hex = 02dec
    43Hex = 67dec
    Ö incoming alarm 400267

    This alarm is also displayed on the HMI.

    Alarm description:
    400267 access error
    Explanation: MCP resp. handheld unit data could not be accessed
    Response: Alarm display.
    Remedy: Check MCP resp. handheld unit parameters of FB1.
    Program continuation: Switch controller ON / OFF

    Solution:
    Configure parameters MCP1StatSend and MCP1StatRec to max. A 124 (PLC 315) resp.
    max. A 252 (PLC 317).
    Subject to change withput prior notice.
    © Siemens AG 2008 Page 1 / 1 Edition: 14.03.2008
    1-CWSJVZ-Attachment_en.doc

    You might also like