PARTTT

MAINTENANCE MANUAL 73-10-07 - COMPRESSOR DELIVERY AIR LINES - MAINT.
PRACTICES
Manual Part No.3034342 Rev. 52.0 - 08/APR/19
73-10-07
Figure 201 Removal/Installation of P3 Air Filter Element
c13113a
Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 1

Printed on 09/MAY/19 P&WC Proprietary – subject to restrictions in Technical Data Agreement
MAINTENANCE MANUAL 73-10-07 - COMPRESSOR DELIVERY AIR LINES - MAINT. PRACTICES
1. Air Filter Cover (Pre-SB13175)

2. Preformed Packing (Pre-SB13175)
3. Filter Element (Pre-SB13175)
4. Locating Spigot (Ref.)
5. Air Filter Housing (Ref.)
6. Preformed Packing (Pre-SB13175)
7. Drain Valve Adapter (Post-SB13175)
8. Preformed Packing (Post-SB13175)
9. Spring (Post-SB13175)
10. Drain Valve (Post-SB13175)
11. Retaining Ring (Post-SB13175)
12. Filter Cover (Post-SB13175)
15. Filter Element (Post-SB13175)

6. Removal/Installation
CAUTION: WHEN REMOVAL OR INSTALLATION OF AN INDIVIDUAL ITEM IS REQUIRED,

IT IS ESSENTIAL THAT TUBES ARE NOT SUBJECTED TO BENDING STRESSES.
UNDER NO CIRCUMSTANCES BEND OR FORCE TUBES IN OR OUT OF
POSITION. WHEN REMOVING ANY ONE TUBE, THE ADJACENT TUBE,
COUPLING OR ELBOW, TOGETHER WITH SEAL RETAINING PLATES (IF
APPLICABLE), MUST FIRST BE REMOVED, AND THE PROCEDURE REVERSED
AT REINSTALLATION.
A. Removal of Compressor Delivery Air Lines (Ref. Fig. 202)

(1) Remove bolt (2) and self-locking nut (5) fastening loop clamp (4) to support bracket (3).
Keep loop clamp on rear tube assembly (1).
(2) Disconnect coupling nuts and remove rear tube assembly (1) from between FCU and filter
housing (6).
(3) Pre-SB13323:
(a) Remove nut (7) and bolt (13) fastening loop clamp (8) of front tube assembly (9). Keep
clamp on tube assembly (9).
(b) Disconnect rear coupling nut and remove front tube assembly (9) from filter housing
(6) forward of rear mount ring.
(c) Remove bolts (10) fastening front tube assembly (9), adapter (12) and gasket (11).
Discard gasket (11).
(4) Post-SB13323:
(a) Remove nut (7) and bolt (13) fastening loop clamp (8) of front tube assembly (14).
Keep clamp on tube assembly (14).
(b) Disconnect rear coupling nut and remove front tube assembly (14) from filter housing
(6) forward of rear mount ring.
(c) Remove bolts (10) fastening front tube assembly (14) and gasket (11). Discard gasket
(11).
(5) Install suitable protective caps or covers on tubes and

openings.

Figure 202 Removal/Installation of Compressor Delivery Air Lines
c176722

1. Rear Tube Assembly

2. Bolt
3. Bracket
4. Loop Clamp
5. Nut, self-locking
6. Filter Housing
7. Nut, self-locking
8. Loop Clamp
9. Front Tube Assembly (Pre-SB13323)
10. Bolt
11. Gasket
12. Adapter (Pre-SB13323)
13. Bolt
14. Front Tube Assembly (Post-SB13323)

B. Removal of Air Filter Housing Post-SB13175 Drain Valve (Ref. Fig. 201)
(1) Remove filter cover (12) and discard preformed packing
(13).
(2) Remove drain valve adapter (7) and discard preformed packing
(8).
(3) Remove retaining ring (11), drain valve (10) and spring
(9).
C. Installation of Compressor Delivery Air Lines (Ref. Fig. 202)
CAUTION: HOLD THE FITTING CORRECTLY IN POSITION WHEN YOU TORQUE THE
COUPLING NUT.
NOTE: It is important to make sure that all solid P3 lines are properly and correctly fitted
before the coupling nuts are tightened. The coupling nuts should be seated without the
use of tools (finger tight) before torquing. The installation of any brackets or clamps
should not distort the line in any way.
(1) Pre-SB13323: Install front tube assembly (9), adapter (12) and gasket (11) on P3 boss on
gas generator case with two bolts (10). Connect coupling nut to P3 filter housing (6). Do not
tighten coupling nut at rear of tube.
(2) Post-SB13323: Install front tube assembly (14) between P3 port on gas generator case and
nipple on P3 air filter housing (6). Install gasket (11) under flange and loosely attach flange
to gas generator case with bolts (10). Do not tighten coupling nut at rear of tube.
NOTE: Do not lockwire components until completion of pressure test (Ref.
Adjustment/Test).
(3) Install rear tube assembly (1) between fitting at P3 input port on FCU and filter housing (6),
passing tube assembly between fuel interconnect hose and fuel pump. Tighten coupling nuts
90 to 100 lbf.in.
(4) Fasten loop clamp (2), spacer (13) and rear tube to bracket (3) with bolt (2) and self-
locking nut (5). Tighten nut 36 to 40 lbf.in.
(5) Leak test fuel control pneumatic system (Ref.
Adjustment/Test).
D. Installation of Air Filter Housing Post-SB13175 Drain Valve (Ref. Fig. 201)
(1) Install spring (9), drain valve (10) into adapter (7) and install retaining ring (11). Make sure
valve moves smoothly and freely, and that retaining ring is installed properly.
CAUTION: COVER (12) MUST NOT BE INSTALLED IN FILTER HOUSING WHEN YOU
TIGHTEN THE ADAPTER.
CAUTION: THE P3 FILTER COVER IS MADE FROM ALUMINUM ALLOY. TAKE CARE
NOT TO DAMAGE THE COVER ASSEMBLY WHEN LOCKWIRING THE
DRAIN VALVE ASSEMBLY TO THE COVER ASSEMBLY. BEFORE
LOCKWIRING, EXAMINE THE LOCKWIRE ATTACHMENT HOLES ON THE
COVER ASSEMBLY FOR EVIDENCE OF TEARING. IF TEARING IS
EVIDENT, SECURE LOCKWIRE TO AN ALTERNATE SERVICEABLE
LOCATION (REF. 70-00-00, STANDARD PRACTICES - MAINTENANCE
PRACTICES).
(2) Install preformed packing (8) on adapter (7), and install valve assembly in cover. Torque
adapter (7) 225 to 250 lb. in. and lockwire to cover.
(3) Install preformed packing (13) on filter cover (12). Lubricate threads of cover with oil
(PWC03-001) and install in filter housing. Torque cover 60 to 70 lb. in.
(4) Leak test fuel control pneumatic system (Ref.
Adjustment/Test).
(5) Lockwire air filter cover (12) when no leaks have been detected or

found.
7. Cleaning/Painting
A. Cleaning of P3 Air Filter (Ref. Fig. 203)
(1) Place P3 filter element vertically, with open end of element at bottom, in cleaning tank or
suitable electrosonic cleaner, generating less than 10 kHz.

Figure 203 Cleaning of P3 Air Filter Element
c7140e

(2) Pour sufficient quantity of solvent (PWC11-002) or (PWC11-014) into tank to a level
approximately 1/4 inch below top.
(3) Operate cleaner for 10
minutes.
(4) Turn element 180 degrees (open end of element at
top).
(5) Operate cleaner for five
minutes.
(6) Turn element to original position in tank (Ref. Step (1)
).
(7) Operate cleaner for five minutes.
NOTE: Cleaning duration should be adjusted to suit condition of filter element. However, for
optimum results, cleaning solvent should be replaced every 20 minutes.
(8) Wear clean, lint-free gloves and remove element from
tank.
(9) Dry element with clean, dry compressed air (30
psi).
(10)Inspect filter element (Ref. Inspection/Check).
(11)Vibropeen cleaning date on end cap.
(12)Store cleaned filter elements in clean polyethylene bags until required for installation.
B. Cleaning of Air Tubes
CAUTION: DURING CLEANING, MAKE SURE SOLVENT DOES NOT CONTACT

RUBBER INSULATED SECTIONS OF AIR TUBE ASSEMBLIES.
(1) Pressure flush tubes with solvent (PWC11-027) or (PWC11-
031).
(2) Dry interior and exterior of tubes using clean, dry compressed
air.
(3) Cap open ends to prevent ingress of dirt, oil or other contaminants until tubes are required
for installation.
C. Cleaning of Air Filter Housing Post-SB13175 Drain Valve Adapter (Ref. Fig. 201)
(1) Clean adapter (7), spring (9), and valve (10) with solvent (PWC11-027) or (PWC011-31)
and non-metallic bristle brush.
8. Inspection/Check
A. Inspection of Air Tubes
(1) Examine air tubes (Ref. 70-00-00, INSPECTION, Inspection of Fuel, Oil and Air
Tubes).
(2) Examine insulation for cuts in outer rubber sheath. Surface cuts up to three inches long may
be repaired (Ref. Approved Repairs).
B. Inspection of Air Filter Element
(1) Inspect air filter element at intervals recommended in Chapter 72-00-00, INSPECTION,
Periodic Inspection. Filter must be free of visible heavy contamination, and should not
provide undue restriction when blown through. If repeated electrosonic cleaning (Ref.
Cleaning/Painting) fails to restore filter to an acceptable condition, filter element should be
shipped to an approved overhaul facility for ultrasonic cleaning and flow checking.
(2) Use a 10x magnifying glass to inspect the filter element for detachment of end cap or
broken wires. Reject element if any of these conditions are evident.
C. Inspection of Air Filter Housing Post-SB13175 Drain Valve Adapter (Ref. Fig. 201)

(1) Filter Cover (12):

(a) Check lockwire holes for damage (tearing, cracks).
(b) Check threads for damage.
(c) Check that contact area is free of nicks and/or
scratches.
(2) Drain Valve Adapter (7):

(a) Check threads for damage.
(b) Check contact area is free of nicks and/or scratches.
(c) Check flats and lockwire holes are free of damage.
(d) Check retaining ring groove. Reject if damaged or
worn.
(3) Drain Valve (10):

(a) Check contact area is free of nicks and/or
scratches.
(b) Make sure drain holes are clear and unobstructed.
(4) Valve Spring (9):

(a) Check for corrosion and/or damage. Reject if
unsatisfactory.
(5) Retaining Ring (11):

(a) Check for distortion. Replace if
distorted.


PARTTT

Uploaded by

Copyright:

Available Formats

PARTTT

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PARTTT

Uploaded by

Copyright:

Available Formats

MAINTENANCE MANUAL 73-10-07 - COMPRESSOR DELIVERY AIR LINES - MAINT.

Figure 201 Removal/Installation of P3 Air Filter Element

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 1

1. Air Filter Cover (Pre-SB13175)

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 2

CAUTION: WHEN REMOVAL OR INSTALLATION OF AN INDIVIDUAL ITEM IS REQUIRED,

A. Removal of Compressor Delivery Air Lines (Ref. Fig. 202)

(5) Install suitable protective caps or covers on tubes and

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 3

Figure 202 Removal/Installation of Compressor Delivery Air Lines

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 4

1. Rear Tube Assembly

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 5

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 6

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 7

Figure 203 Cleaning of P3 Air Filter Element

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 8

CAUTION: DURING CLEANING, MAKE SURE SOLVENT DOES NOT CONTACT

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 9

(1) Filter Cover (12):

(2) Drain Valve Adapter (7):

(3) Drain Valve (10):

(4) Valve Spring (9):

(5) Retaining Ring (11):

Export Classification: ECCN=Contains 1025% 9E991;ECL=NSR Page 10

You might also like