International Journal of Current Engineering and Technology E-ISSN 2277 – 4106, P-ISSN 2347 – 5161

©2017 INPRESSCO®, All Rights Reserved Available at http://inpressco.com/category/ijcet

Research Article

Impact of Card Production Rate on the Quality of Ring Yarn

Md. Rokonuzzaman#, Ahmed Jalal Uddin!, Md. Abu Bakar Siddiquee#, Md. Abdullah Al Mamun# and A. K. M.
Ayatullah Hosne Asif#*
#Department of Textile Engineering, Mawlana Bhashani Science and Technology University, Santosh, Tangail-1902,
!Department of Textile Engineering, Ahsanullah University of Science and Technology, Tejgoan Industrial Area, Dhaka-1208

Accepted 10 Jan 2017, Available online 09 Feb 2017, Vol.7, No.1 (Feb 2017)

Abstract

The quality for any production process is usually inversely proportional to quantity. In the current work, this
relationship has been shown in between the productivity of carding machine and the quality of respective it produced.
Keeping the hank of delivery sliver constant (0.11 Ne here), card production rate (delivery speed of carding machine)
was gradually increased from 60 -180 meter/min at five steps (60, 90, 120, 150 and 180 meter/min respectively).
Subsequently 30/1 Ne carded ring knit yarns were produced with each sliver. The quality parameters of card sliver
and yarns were studied by employing various instruments such as Uster AFIS (Advanced Fibre Information System),
Uster evenness tester and yarn strength tester. It was found that with the increase of card production rate, the
irregularity (Um% and CVm%) of card sliver and consequently the irregularity of yarn increased. Nep removal
efficiency% of card decreases with increasing card production rate that directly reflected to high nep count in yarns.
Thick and thin places of yarns are also reported higher with the increase of card production rate. Higher irregularity
and imperfections of yarns caused from higher card speed resulted in the decrease in yarn strength. Nep removal
efficiency of card, irregularity of sliver and yarn as well as imperfections (thick places, thin places and neps), yarn
hairiness, yarn strength were found more satisfactory level at the card production rate of 60-120 meter/min. On the
contrary nep removal efficiency of card, irregularity of sliver and yarn as well as imperfections, yarn strength, yarn
hairiness at the card production rate of 180 meter/min were not found satisfactory. In this study card production
rate 150 meter/min showed optimized delivery speed for satisfactory level of nep removal efficiency, irregularity as
well as imperfections, hairiness and yarn strength.

Keywords: Nep removal efficiency, Carding, Imperfections, Production rate, Ring yarn

1. Introduction carding productivity has been made possible by the

developments in several sciences and fields such as
1 Carding is the most important machine in spinning. It machinery, material science, automation and control.
contributes a lot to the yarn quality. “The card is the These developments permit several ways for
heart of the spinning mill’’ and “Well-carded is half- increasing carding productivity. The carding quality
spun” are two proverbs of the experts. primarily depends on the area of the cylinder. The
These proverbs inform the immense significance of revolving flat keeps an important role to maintain the
carding in the spinning process. High production in carding quality. An optimal number of flat bar is
responsible for cleaning as well as removing neps and
carding to economize the process leads to reduction in
short fibres in carding machine. The pre-carding area
yarn quality. Higher the production, the more sensitive
with its cleaning and carding elements perform for
becomes the carding operation and the greater danger cleaning and removing neps and short fibres. The
of a negative influence on quality. The technological higher the pre-opening, the more intense the carding
change that has taken place in the process of carding is that resulting in high production. The object of high
remarkable. Production got from carding machine 5-10 speed carding is to increase the card productivity
kgs/hour up to 1970, at present latest carding without reducing carding quality, or even improve it. It
machines produce the production rate of 60-100 had been thought that fibre breakage would increase
kgs/hour. due to the increase of card delivery speed, but there is
Since carding is an intricate process, it involves a no evidence to increase fibre breakage as card delivery
number of parameters and different technologies that speed increases.
improve the carding productivity. Improving the It was necessary to increase the production rate of
the carding machine due to new technologies with
*Corresponding author: A. K. M. Ayatullah Hosne Asif considerably higher production levels were started to
144| International Journal of Current Engineering and Technology, Vol.7, No.1 (Feb 2017)
Md. Rokonuzzaman et al Impact of Card Production Rate on the Quality of Ring Yarn

be implemented. Carding action can be described as each finisher drawn sliver was fed in simplex machine
the combing of fibers between two surfaces, which for making roving. Each roving sample was taken to
carry a set of angled wires (card clothing) oriented in Uster evenness tester for testing roving unevenness.
opposing directions, when their relative speed is After that all roving sample were fed in ring frame
greater than zero. Ishtiaque, S. M., Chaudhuri, S. and machine and producing 30S/1 carded knit yarn. All
Das, A. observed the effect of fibre openness at carding yarn samples were taken to Uster evenness tester for
and it has been found that yarn irregularity and testing yarn unevenness, imperfections and hairiness
tenacity are improved due to fibre openness only up to and Lea Strength Tester for testing CSP (Count
a certain level and then yarn irregularity and tenacity Strength Product). The linear densities of the prepared
card sliver, draw frame sliver and roving were Ne 0.11,
do not improve further increase of fibre openness at
Ne 0.11 and Ne 0.81 respectively. Before testing, all the
carding.
yarn samples were conditioned in the laboratory under
Card draft, coiler diameter and draw frame delivery
standard atmospheric conditions of 20±20C and a
speed are also found to have significant effect on yarn
relative humidity of 65±2% for 24 hours.
properties. It has been reported that yarn tenacity,
breaking elongation, evenness and hairiness are
3. Results and discussion
upgraded due to increase in card coiler diameter and
draw frame delivery speed, and yarn quality
Effect of Card Delivery Speed on Nep Removal
deteriorate due to the increase in card draft of carding
Efficiency%
machine beyond a certain point (Istiaque et al, 2008). If
card coiler diameter, card draft, and draw frame
Nep Removal Efficiency% (NRE%)
delivery speed increase percentage of trailing, leading
and total fiber hooks decrease (Istiaque et al, 2009).
The card causes lap-ups in the cylinder of card and = 100
formation of too many neps due to excessive beating in
the heavier lap (Salhotra et al, 1989). Table 1: Test result of NRE% (Nep Removal Efficiency
Some researchers investigated that, the reduction %) of carding machine
in card production rate improves the removal of neps
at carding stage significantly due to the intensive Card delivery
NRE (Nep
carding action. Neps level tends to increase further at Card mat Card sliver Removal
Machine speed
(neps/gm) (neps/gm) Efficiency)
the drawing with higher card production rate. Neps can (meter/min)
(%)
generate at draw frame due to inferior quality of card 60 39 88.56
sliver at the higher card production rate. The yarn 90 41 87.97
tenacity improves at lower card production rate Carding 120 341 43 87.39
because of better carding quality (Rakshit et al, 1985). 150 51 85.04
180 69 79.76
Neps in the drawn sliver mainly increase due to
inferior carding quality at higher card production rate.
From table 1, it is observed that if the delivery speed of
Neps do not generate after carding due to the number
carding machine increases, nep removal efficiency% of
of draw frame passage. With the increase in card
carding machine decreases. As a result, poor quality
production rate thick places and neps in ring yarn also
sliver will be produced and yarn quality will be
increase. However, with the increase in card
deteriorated.
production rate the yarn unevenness increases
marginally (Rakshit et al, 1983). Effect of card delivery speed on Um(%) and CVm(%) of
card sliver
2. Materials and method
4
One carding machine was selected for sample
3.5
preparation and five samples were taken from the Um(%)
Um(%) and CVm(%)

3
same carding machine with the card delivery speed of
2.5
60 m/min, 90 m/min, 120 m/min, 150 m/min and 180 CVm(%)
m/min. Then each sample was taken to Uster AFIS PRO 2

for testing neps per gm of sliver and Uster evenness 1.5

tester for testing sliver unevenness. Each sample of 1

card sliver was then fed in breaker draw frame to 0.5
produce breaker drawn sliver. 0
60 90 120 150 180
Each breaker drawn sliver was taken for testing
sliver unevenness with Uster evenness tester. Then Card delivery speed (m/min)
each breaker drawn sliver was fed in finisher draw
frame and producing finisher drawn sliver. Each
sample of finisher drawn sliver was taken to Uster Figure 1: Card delivery speed vs Um(%) and CVm(%)
evenness tester for testing sliver unevenness. Then of card sliver
145| International Journal of Current Engineering and Technology, Vol.7, No.1 (Feb 2017)
Md. Rokonuzzaman et al Impact of Card Production Rate on the Quality of Ring Yarn

From figure 1, it is observed that if card delivery speed Effect of card delivery speed on Um (%) and CVm (%) of
increases, Um (%) and CVm (%) of card sliver also roving
increases.
6 Um(%)
Effect of card delivery speed on Um (%) and CVm (%) of
5

Um(%) and CVm(%)

breaker draw frame sliver. CVm(%)
4

4 3

3.5 Um(%) 2
Um(%) and CVm(%)

3 1
2.5 CVm(%)
0
2 60 90 120 150 180
1.5
Card delivery speed (m/min)

1
Figure 4: Card delivery speed vs Um(%) and CVm(%)
0.5
of roving
0
60 90 120 150 180 With increasing the delivery speed of carding machine,
Card delivery speed (m/min) there is also no significant effect of Um(%) and
CVm(%) in roving which is observed in figure 4. But
Um(%) of roving increases compared to Um(%) of
Figure2: Card delivery speed vs Um (%) and CVm (%) finisher draw frame sliver with increasing the card
of breaker draw frame sliver delivery speed due to draft in simplex machine.

From figure 2, it is observed that there is no significant Effect of card delivery speed on Um (%) and CVm (%) of
30s/1 carded ring knit yarn
effect of Um(%) and CVm(%) in breaker draw frame
sliver with increasing the card delivery speed. Since no
variations in Um(%) of card sliver, so naturally no 18 Um(%)
16
variations will arise in Um(%) of breaker draw frame CVm(%)
Um(%) and CVm(%)

14
12
sliver.
10
8
Effect of card delivery speed on Um(%) and Cvm(%) of 6
4
finisher draw frame sliver 2
0
60 90 120 150 180
3 Card delivery speed (m/min)
Um(%)
2.5 CVm(%)
Figure 5: Card delivery speed vs Um (%) and CVm (%)
Um(%) and CVm(%)

2 of 30S/1 carded ring knit yarn

1.5
From figure 5, it is observed that if the delivery speed
1 of carding machine increases, Um(%) and CVm(%) of
0.5 30S/1 carded ring knit yarn also increases which
produces poor quality of yarn.
0
60 90 120 150 180 Effect of card delivery speed on Imperfections of 30 s/1
Card delivery speed (m/min)
carded ring knit yarn
Imperfections/km = [Thin places (-50%)/km + Thick
Figure3: Card delivery speed vs Um(%) and CVm(%) places (+50%)/km + Neps (+200%)/km] (For ring
of finisher draw frame sliver yarn).
From table 2, It is observed that, if card production rate
There is no significant effect of Um(%) and CVm(%) in increases, thin places (-50%)/km, thick places
finisher draw frame sliver with increasing the delivery (+50%)/km and neps (+200%)/km of 30S/1 carded
speed of carding machine which is observed in figure 3. ring knit yarn also increases significantly due to
improper carding action i.e. with increasing the card
Moreover, autoleveller at finisher draw frame leveled production rate of carding machine, imperfections of
the delivered sliver, so no variations occurred and 30S/1 carded ring knit yarn increases rapidly. So,
delivery speed of carding machine should be kept as
reduced Um(%) of finisher draw sliver compared to minimum as possible for producing better quality of
breaker draw frame sliver. yarn.
146| International Journal of Current Engineering and Technology, Vol.7, No.1 (Feb 2017)
Md. Rokonuzzaman et al Impact of Card Production Rate on the Quality of Ring Yarn

Table 2: Test result of Imperfections of 30S/1 carded ring knit yarn

Thin Thick
Card delivery Spindle Neps Imperfection/km
places places
Machine speed speed TPI (+200%) (IPI/km)
(-50%)per (+50%) per
(metre/min) (rpm) per km
km km
60 5 242 95 342
90 7 280 118 405
Ring 120 15000 19.92 10 284 143 437
frame 150 17 305 177 499
180 18 373 227 618

Effect of card delivery speed on Hairiness of 30 S/1 removal efficiency that have direct impact on
carded ring knit yarn irregularity and imperfections (thick, thin and neps) of
yarns. Alongside higher hairiness of yarns for higher
5.95
card speed indicates lower integration of fibres with
Hairine the yarn body. The higher irregularity, higher
5.9 ss (-)
imperfections and lower integration of fibres with yarn
Yarn hairiness (-)

5.85 result the yarn strength to be lowered. At the

5.8 production rate of 60 to 120 m/min increases nep
5.75 removal efficiency of carding machine, reduces
5.7
irregularity (Um% and CVm%) of sliver and yarn,
imperfections (thick places, thin places and neps), yarn
5.65
hairiness and increases yarn strength. On the other
5.6 hand card delivery speed 180 m/min produces lower
60 90 120 150 180
nep removal efficiency of card and lower yarn strength,
Card delivery speed (m/min) also produces higher irregularity of sliver and yarn,
more imperfections and hairiness. The card delivery
speed 150 m/min shows better nep removal efficiency
Figure 6: Card delivery speed vs. Hairiness of 30S/1 of carding machine, better irregularity of sliver and
carded ring knit yarn yarn as well as better imperfections.
As a part of process optimization, the card speed
Fromthe above figure, it is observed that yarn hairiness should, therefore, be selected in accordance with the
increases with increasing the card delivery speed. quality of fabric that will be made from respective
yarns.
Effect of card delivery speed on CSP of 30S/1 carded ring
knit yarn Acknowledgement
The author gratefully acknowledges the authority of
Youth Spinning Mills Ltd., Gorai, Mirzapur, Tangail for
2540 CSP
2520 giving the opportunity to conduct this study in the
2500 factory.
2480
2460
2440 References
2420
CSP

2400
Klein, W. (1987), A short staple spinning series, A Practical Guide to
2380 Opening and Carding, The Textile Institute, 33.
2360 http://www.geocities.com/vijaykumar777/carding.html
2340 Atkinson, K.R., Harrowfield, B.V., Plate, D.E.A., Robinson, G.A. (1986),
60 90 120 150 180 Increasing card productivity, wool scouring and worsted carding: new
Card delivery speed (m/min)
approaches.CSIRO Division of Textile Industry Symposium.
Ishtiaque, S. M., Chaudhuri, S., & Das, A. (2003), Influence of fiber
openness on processibility of cotton and yarn quality. Part II:Effect of
carding parameters, Indian Journal of Fibre and Textile Research, 28,
pp 405-410.
Figure 7: Card delivery speed vs. CSP of 30S/1 carded Ishtiaque, S. M., Mukhopadhyay, A., & Kumar, A. (2008), Influence of draw
ring knit yarn frame speed and its preparatory on ring yarn properties. Journal of the
Textile Institute, 99, pp 533-538.
Ishtiaque, S. M., Mukhopadhyay, A., & Kumar, A. (2009), Impact of carding
From figure 7, it is observed that there is no significant parameters and draw frame speed on fiber axial distribution in ring
effect of yarn CSP with increasing the card delivery spun yarn, Indian Journal of Fibre &Textile Research, 34, pp 231-238.
Salhotra, K. R. (1989), Spinning of man mades and blends on cotton
speed. Since higher IPI at higher card speeds, so CSP systems, Textile Association India.
also lower which is also observed in this figure. Istiaque, S. M. & Vijay, A. (1994), Optimization of ring frame parameters
for coarser preparatory, Indian Journal of fibre and Textile Research,
19, pp 239-246.
Conclusion Rakshit, A. K., & Balasubramanian, N. (1985), Influence of carding
conditions on rotor spinning performance and yarn quality, Indian
The increase in card production speed implying Journal of Textile Research, 10, pp 158-162.
Rakshit, A. K., & Balasubramanian, N. (1983), Nep generation with
improper carding action causes the increase in polynosicfibres in relation to surface characteristics of fibre, Indian
irregularity of card sliver and decrease the nep Journal of Textile Research, 8, pp 95-100.

147| International Journal of Current Engineering and Technology, Vol.7, No.1 (Feb 2017)