Owner’s manual

ENGLISH

1
This manual forms an integral part of the motorcycle and must be kept with it whole its service life.
If the motorcycle is resold, the manual must always be handed over to the new owner.
This manual must be preserved with care. If it lost or becomes damaged, contact a Ducati Dealer or authorised
Service Centre without delay to obtain a new copy of the manual.
The quality standards and safety of Ducati motorcycles are steadily improved as new design solutions,
equipment and accessories are developed. While the information contained in this manual is current at the
time of going to print, Ducati Motor Holding S.p.A. reserves the right to make changes at any time without
notice and without any obligations. For this reason, the illustrations in this manual might differ from your
motorcycle.
Any and all reproduction or spreading of the contents herein in whole or in part is forbidden. All rights reserved
to Ducati Motor Holding S.p.A. Any request for written authorisation to do so shall be addressed to this
company, specifying the reasons for request.
Enjoy your ride!

2
Table of contents Acronyms and abbreviations used in the
Manual 26
Technological Dictionary 26
Function push-buttons 29
How to set/display parameters 30
Main functions 38
Riding Mode 44
DTC 48
EBC 55
Foreword 7
DQS 59
Safety guidelines 7
ABS 60
Safety alerts 8
Engine coolant temperature 62
Permitted use 9
Menu 1 functions 65
Rider's obligations 10
Menu 1: Odometer (TOT) 66
Rider training 12
Menu 1: Trip meter 1 (TRIP A) 68
Riding gear 12
Menu 1: Trip meter 1 (TRIP B) 69
Best practices for motorcycle safety 13
Menu 1: Partial fuel reserve counter (TRIP
Refuelling 15
FUEL) 70
Carrying the maximum load allowed 16
MENU 1: Trip time 71
Dangerous products - warnings 17
MENU 1: Clock 72
Vehicle identification number 19
Menu 1: Lap time (LAP time) 73
Engine identification number 20
MENU 2 functions 77
MENU 2: Air temperature 78
Instrument panel (Dashboard) 22 MENU 2: Instantaneous fuel consumption 79
Instrument panel 22 MENU 2: Average fuel consumption 80
MENU 2: Average speed 81

3
Auxiliary functions 82 Setting backlighting 136
Service warning (SERVICE) 84 LAP 138
Zero OIL SERVICE warning 85 Setting the unit of measurement 146
OIL SERVICE or DESMO SERVICE warning 87 Light control 155
Errors 88 The Immobilizer system 160
Displayed error description 90 Keys 161
Setting MENU 95 Operation 162
Customising Riding Modes 97 Duplicate keys 163
Riding mode customisation: Storing Riding Mode Vehicle release through PIN CODE 164
settings 100
Customising Riding Modes: EBC level
setting 102 Controls 168
Customising Riding Modes: DTC level Position of motorcycle controls 168
setting 104 Ignition switch and steering lock 169
Customising Riding Modes: DQS enable/ Left-hand switch 170
disable 106 Clutch lever 171
Riding mode customisation: ABS adjustment 108 Right-hand switch 172
Customising Riding Modes: Engine setting 110 Throttle twistgrip 173
Customising Riding Modes: Restore default Front brake lever 174
settings 112 Rear brake pedal 175
Engine rpm digital indication (RPM) 114 Gear change pedal 176
Battery voltage 115 Adjusting the position of the gearchange and rear
DDA 117 brake pedals 177
Pin Code 122
Changing the PIN CODE 126
Clock 132 Main components and devices 179

4
Position on the vehicle 179 Check and top up the coolant level 206
Tank filler plug 180 Check brake and clutch fluid level 208
Seat lock 181 Check brake pads for wear 210
Side stand 182 Charge the battery 211
Steering damper 184 Charge and maintenance of the battery during winter
Adjusting the front fork 185 storage 214
Adjusting the rear shock absorber 187 Check drive chain tension 216
Chain lubrication 218
Replace the high and low beam bulbs 219
Riding the motorcycle 191 Rear turn indicators 220
Running-in recommendations 191 Beam setting 221
Pre-ride checks 193 Adjust rear-view mirrors 223
Starting the engine 196 Tubeless tyres 224
Moving off 198 Check engine oil level 227
Braking 198 Clean and replace the spark plugs 229
ABS system 198 Clean the motorcycle 230
Stopping the motorcycle 200 Storing the motorcycle 231
Parking 200 Important notes 232
Refuelling 201
Tool kit and accessories 202
Scheduled maintenance chart 233
Scheduled maintenance chart: operations to be
Main maintenance operations 203 performed by the Dealer 233
Remove the fairing 203 Scheduled maintenance chart: operations to be
Side fairings 204 performed by the customer 237
Change the air filter 205

5
Technical data 238
Weights 238
Overall dimensions 239
Top-ups 240
Engine 241
Timing system 242
Performance data 243
Spark plugs 243
Fuel system 243
Brakes 243
Transmission 244
Frame 245
Wheels 245
Tyres 245
Suspensions 245
Exhaust system 246
Available colours 246
Electrical system 247

Routine maintenance record 253

Routine maintenance record 253

6
Foreword Our highly skilled staff have access to special
implements and appropriate equipment required to
perform any servicing job at best, and use Ducati
original spare parts only as the best guarantee for full
interchangeability, smooth running and long life.
Safety guidelines All Ducati motorcycles come with a Warranty Card.
We would like to welcome you among Ducati The warranty does not apply to motorcycles used in
enthusiasts, and congratulate you on your excellent racing competitions. Tampering with or altering any
choice of motorcycle. We think you will ride your components, even partially, will make the warranty
Ducati motorcycle for long journeys as well as short null and void effective immediately. Improper or poor
daily trips. Ducati Motor Holding S.p.A. wishes you maintenance, using other than original spare parts or
smooth and enjoyable riding. parts not expressly approved by Ducati may invalidate
Your motorcycle is the result of Ducati Motor Holding your warranty rights and lead to damage or loss of
S.p.A.'s on-going research and development efforts. performance.
It is important that you preserve its quality standard Your safety and that of other road users are very
by strictly observing the maintenance plan and using important. Ducati Motor Holding S.p.A. recommends
genuine spare parts. that you ride responsibly.
This manual provides instructions on minor Before using your motorcycle for the first time, read
maintenance operations. Major maintenance this entire manual carefully and closely follow the
operations are described in the Service Manual guidelines outlined in it. The manual provides full
available to Ducati Authorised Service Centres. information on proper motorcycle operation and
In your own interest, for your safety and in order to maintenance. In case of any doubts, please call a
guarantee product reliability, you are strongly advised Dealer or Authorised Service Centre.
to refer to our authorised Dealers and Service Centres
for any operations listed in the scheduled
Safety alerts
maintenance chart, see page 233.

7
To alert you to potential hazards that could potentially
harm you or other persons, the following safety alerts
have been used:
- Safety labels on motorcycle;
- Safety messages preceded by a warning symbol
and the word WARNING or IMPORTANT.

Warning
Failure to comply with these instructions may
put you at risk and result in severe injury to rider or
other persons or even death.

Important
Possibility of damaging the motorcycle and/or
its components.

Note
Additional information concerning the job being
carried out.

The terms RIGHT and LEFT are referred to the

motorcycle viewed from the riding position.

8
Permitted use
This motorcycle must be used only on asphalted
roads or on level, regular pavement. This motorcycle
may not be used for riding on dirt trails or for off-road
riding.

Warning
Off-road use may result in loss of control and
lead to vehicle damage or injury or even death.

Warning
This motorcycle may not be used to tow any
trailers or with a side-car attached; this can lead to
loss of control and result in an accident.

This motorcycle is designed to carry the rider and may

carry a passenger when the supplied kit is installed.
The kit may only be installed at a Ducati Dealer or
authorised Service Centre.

Warning
The total weight of the motorcycle in running
order including rider, passenger, luggage and
additional accessories load should not exceed: 370
kg/816 lb.

9
Rider's obligations Warning
All riders must hold a valid licence. Some medications and drugs may cause
drowsiness or other effects that slow down reaction
Warning time and the rider's ability to control the motorcycle,
Riding without a licence is illegal and is possibly leading to an accident.
prosecuted by law. Always make sure you have your
licence with you when riding. Do not let Some states require vehicle insurance.
inexperienced riders or who do not hold a valid
licence use your motorcycle. Warning
Check your state laws. Obtain insurance
Do not ride under the influence of alcohol and/or coverage and keep your insurance document secure
drugs. with the other motorcycle documents.

Warning To protect rider and passenger safety, some states

Riding under the influence of alcohol and/or mandate the use of a certified helmet.
drugs is illegal and is prosecuted by law.
Warning
Do not take prescription or other drugs before riding Check your state laws. Riding without a helmet
unless you have consulted your doctor about their may be punishable by law.
side effects.
Warning
Riders without helmets are more likely to suffer
severe bodily injury or die if they are in an accident.

10
 Warning
Check that your helmet complies with safety
specifications, permits good vision, is the right size
for your head, and carries a certification label
indicating that it conforms to the standards in force in
your state. Traffic laws differ from state to state.
Learn about traffic laws in your state before riding and
always obey them.

11
Rider training - Jacket, pants or riding suit must be made from
Accidents are frequently due to inexperience. Driving leather or abrasion-resistant material and have
a motorcycle is different from driving other vehicles high-visibility colours and inserts.
and requires specific riding and braking techniques.
Important
Warning Never wear loose clothing, items or accessories
Poor training or improper operation of the that may become tangled in motorcycle parts.
vehicle can lead to loss of control, death or severe
damage. Important
For your safety, always wear proper protective
Riding gear gear, regardless of season and weather.
Riding gear is very important for safety. Unlike cars,
a motorcycle offers no impact protection in an Important
accident. Have your passenger wear proper protective
Proper riding gear includes helmet, eye protection, clothing.
gloves, boots, long sleeve jacket and long pants.
- The helmet must meet the requirements listed
at page page 10; if your helmet does not have a
visor, use suitable eye wear;
- Use five-finger gloves made from leather or
abrasion-resistant material;
- Riding boots or shoes must have non-slip soles
and offer ankle protection;

12
Best practices for motorcycle safety Warning
These few simple operations are critical to people Start the engine outdoors or in a well ventilated
safety and to preserving the full performance of your area. The engine should never be started or run
motorcycle. Never forget to perform them before, indoors.
while and after riding. Exhaust gases are poisonous and may lead to loss of
consciousness or even death within a short time.
Important Use proper body position while riding and ensure your
During the whole running-in period, the passenger does the same.
indications recommended in section “Riding the
Motorcycle“ shall be observed carefully. Important
Failure to follow these instructions releases Ducati Rider must hold the handlebars with both hands
Motor Holding S.p.A. from any liability whatsoever for AT ALL TIMES while riding.
any engine damage or shorter engine life.
Important
Warning Both rider and passenger should keep their feet
Before riding your motorcycle, become familiar on the footpegs when the motorcycle is in motion.
with the controls you will need to use when riding.
Important
Perform the checks recommended in this manual The pillion passenger should always hold on to
before each ride (see page page 198). the strap onto passenger seat with both hands.

Warning
Failure to carry out these checks before riding,
may lead to motorcycle damage and injury to rider
and/or passenger.

13
 Important Important
Be very careful when tackling road junctions, or Visually inspect the tyres at regular intervals for
when riding in the areas near exits from private cracks and cuts, especially on the side walls, and
grounds, car parks or on slip roads to access bulges or large stains that indicate internal damage.
motorways. Replace them if badly damaged.
Remove any stones or other foreign bodies caught in
Important the tread.
Be sure you are clearly visible and do not ride
within the blind spot of vehicles ahead. Warning
The engine, exhaust pipes, and silencers stay
Important hot for a long time after the engine is stopped; take
ALWAYS signal your intention to turn or pull to special care not to touch the exhaust system with any
the next lane in good time using the suitable turn part of your body and do not park the motorcycle next
indicators. to inflammable material (wood, leaves, etc.).

Important Warning
Park your motorcycle where no one is likely to Always remove the key when you leave your
hit it and use the side stand. Never park on uneven or motorcycle unattended and make sure it is not
soft ground or your motorcycle may fall over. accessible to persons not authorised to use the
motorcycle.

14
Refuelling Warning
Refuel outdoors with the engine turned off. Fuel is highly inflammable. Clothing with spilled
Do not smoke or use open flames when refuelling. fuel on it should be removed as possible.
Be extremely careful not to spill fuel on the engine or
on the exhaust pipe.
Never fill the tank completely. Fuel should never be
touching the rim of filler recess.
While refuelling, avoid inhaling fuel vapours and avoid
contact with eyes, skin or clothing.

Warning
The vehicle is only compatible with fuel having
a maximum content of ethanol of 10% (E10).
Using fuel with ethanol content over 10% is
forbidden. Using it could result in severe damage of
the engine and motorcycle components. Using fuel
with ethanol content over 10% will make the
warranty null and void.

Warning
In the event of illness after prolonged breathing
of fuel vapours, stay outdoors and seek medical
advice. In the event of contact with eyes, flush with
plenty of water. After contact with skin, wash
immediately with water and soap.

15
Carrying the maximum load allowed Important
Your motorcycle is designed for long-distance riding, Be sure to secure the luggage to the supports
carrying the maximum load allowed in full safety. provided on the motorcycle as firmly as possible.
Even weight distribution is critical to preserving these Improperly secured luggage may affect stability.
safety features and avoiding trouble when
performing sudden manoeuvres or riding on bumpy Important
roads. Do not insert any objects you may need to carry
into the gaps of the frame as these may foul moving
Warning parts.
Do not exceed the total permitted weight for the
motorcycle and pay attention to information provided Warning
below regarding load capacity. Make sure the tyres are inflated to the proper
pressure and that they are in good condition.
Information about carrying capacity
Refer to paragraph "Tyres" on page 224.
Important
Arrange your luggage or heavy accessories in
the lowest possible position and close to motorcycle
centre.

Important
Never fix bulky or heavy objects to the
handlebar or to the front mudguard as this would
affect stability and cause danger.

16
Dangerous products - warnings Warning
Used engine oil The brake fluid used in the brake system is
corrosive. In the event of accidental contact with eyes
or skin, wash the affected area with abundant running
Warning water.
Prolonged or repeated contact with used engine
oil may cause skin cancer. If exposed to used engine Coolant
oil on a daily basis, make it a rule to wash your hands
thoroughly with soap immediately after use. Keep Engine coolant contains ethylene glycol, which may
away from children. ignite under particular conditions, producing invisible
flames. Although the flames from burning ethylene
Brake lining debris glycol are not visible, they are still capable of causing
severe burns.
Never attempt to clean the brake assembly using
compressed air or a dry brush. Warning
Brake fluid Take care not to spill engine coolant on the
exhaust system or engine parts.

Warning These parts may be hot and ignite the coolant, which
Avoid spilling brake fluid onto plastic, rubber or will subsequently burn with invisible flames. Coolant
painted parts of the motorcycle to avoid the risk of (ethylene glycol) is an irritant and is poisonous when
damage. Protect these parts with a clean shop cloth ingested. Keep away from children. Never remove
before proceeding to service the motorcycle. Keep the radiator cap when the engine is hot. The coolant
away from children. will be scalding hot and is under high pressure.

17
The cooling fan operates automatically: keep hands
well clear and make sure your clothing does not snag
on the fan.
Battery

Warning
The battery gives off explosive gases; keep it
away from any source of ignition such as sparks,
flames and cigarettes. Charge the battery in a well-
ventilated area.

18
Vehicle identification number

Note
These numbers identify the motorcycle model
and should always be indicated when ordering spare
parts.

It is recommended to record the frame number of

your motorcycle in the space below.
Frame number

Fig. 1

19
Engine identification number

Note
These numbers identify the motorcycle model
and should always be indicated when ordering spare
parts.

The engine identification number is located in the

motorcycle front side on the horizontal head cylinder
lower side, near the starter motor and the generator
cover.
It is recommended to record the number of your
motorcycle's engine in the space below. Fig. 2

Engine number

20
PAGE INTENTIONALLY LEFT BLANK

21
Instrument panel (Dashboard) Comes on when fuel is low and there are about 5
litres of fuel left in the tank.
6) TURN INDICATOR LIGHTS (GREEN).
Illuminates and flashes when the turn indicator is in
operation. They flash at the same time when the
Instrument panel "Hazard" function (4 turn indicators) is active.
1) Display. If the right or left warning light flashes "quickly" it
2) NEUTRAL LIGHT N (GREEN). indicates an error / failure of at least one of the turn
Comes on when in neutral position. indicators.
3) HIGH BEAM LIGHT (BLUE). 7) "ENGINE/VEHICLE DIAGNOSIS - EOBD" LIGHT
It turns on to indicate that the high beam lights are on (AMBER YELLOW).
and when the flasher is activated. It turns on in the case of "engine" and/or "vehicle"
4) ENGINE OIL PRESSURE LIGHT (RED). errors and in some cases will lock the engine.
Comes on when engine oil pressure is too low. It 8) GENERAL WARNING LIGHTS (RED).
must turn on at "Key-ON", but must turn OFF a few the lights (8a) turn on when RPM value reaches the
seconds after the engine has started. It may shortly first threshold before the rpm limiter kicks in;
come on when the engine is hot, however, it should the lights (8b) turn on when RPM value reaches the
go out as the engine revs up. second threshold before the rpm limiter kicks in.

Important
If the ENGINE OIL light stays ON, stop the
engine or it may suffer severe damage.

5) FUEL WARNING LIGHT (AMBER YELLOW).

22
9) ABS LIGHT (AMBER YELLOW) .
This turns on to indicate that ABS is disabled or not functioning.

Engine ON / speed below or equal to 5 km/h (3 mph)

Light OFF Light flashing Light steady
- ABS disabled with the menu function "ABS" ABS enabled, but not functioning
yet
Engine ON / speed above 5 km/h (3 mph)
Light OFF Light flashing Light steady
ABS enabled and function- - "Slowly" flashing warning light if the ABS ABS disabled and not functioning
ing system has been disabled with the cor- due to a problem
rect procedure.
- "Quickly" flashing warning light if the
ABS system is in the temporary ena-
bling/disabling status.

23
10) DTC INTERVENTION (AMBER YELLOW). Key-ON status Light OFF
DTC Key-OFF status Light ON flashing
No intervention Light OFF Key-OFF status for Light OFF
over 12 hours
Spark advance cut Light steady ON
Injection cut Light steady ON

11) OVER REV / IMMOBILIZER / ANTI-THEFT

SYSTEM (RED)
Over rev
No intervention Light OFF
First threshold (N Light steady ON
RPM before the limit-
er kicks in)
Limiter Light ON flashing

Note
Each calibration of the Engine Control Unit may
have a different setting for the thresholds that
precede the rev limiter and the rev limiter itself.

Immobilizer

24
6 7 9 2 8a 8b 11 10 8c 8c 4 3 5 6

Fig. 3

25
Acronyms and abbreviations used in the Engine Brake Control (EBC)
Manual The engine brake control system (EBC) works
ABS together with the slipper clutch to avoid and control
Antilock Braking System the rear wheel lock-up during aggressive
BBS downshifting.
Black Box System If the system detects wheel slipping, it sends a signal
CAN to the engine control unit to slightly increase engine
Controller Area Network rpm until the rear wheel speed is again consistent
DDA with vehicle speed.
DUCATI Data Acquisition EBC features a three-tiered operating system and is
DSB integrated in the three Riding Modes.
Dashboard
DTC Riding Mode
DUCATI Traction Control The rider of an 899 Panigale can choose from 3
DQS different preset motorcycle configurations (Riding
DUCATI Quick Shift Modes) and pick the one that best suits his/her riding
EBC style or ground conditions. The Riding Modes allow
DUCATI Engine Brake Control user to instantly change the engine power delivery
ECU (Power Mode), ABS, DTC, DQS and EBC settings and
Engine Control Unit instrument panel graphics.
E-LOCK The Riding modes available for the 899 Panigale are:
Electronic Main Switch Set Race, Sport and Wet. Within every Riding Mode, the
GPS rider can customise any settings.
Global Positioning System
Power Mode
Technological Dictionary

26
The Power Modes are the different engine maps the through eight different levels that are programmed to
rider can select to change power level and delivery to offer a different tolerance level to rear wheel slipping.
suit his/her own riding style and surface conditions. Each Riding Mode features a pre-set intervention
For the 899 Panigale there are three Power Modes, level.
one for each Riding Mode: Level eight indicates system intervention whenever
a slight slipping is detected, while level one is for very
- HIGH;
expert riders because it is less sensitive to slipping
- MED;
and intervention is hence more rare.
- LOW.
Anti-lock Braking System (ABS) 9M
Ride by Wire (RbW)
ABS 9M system fitted to 899 Panigale is a two-
The Ride by Wire system is the electronic device that channel latest-generation system that actuates
controls throttle opening and closing. Since there is combined braking with anti lift-up function for the rear
no mechanical connection between the throttle wheel so as to guarantee not only a reduced stopping
twistgrip and the throttle bodies, the ECU can adjust distance, but also a higher stability under braking.
power delivery by directly affecting throttle opening ABS 9M system is specifically calibrated for sport
angle. use, and features 3 different levels of intervention,
The Ride by Wire system allows you to obtain one per Riding Mode. In RACE mode the system only
different power level and delivery according to the works on the front discs to ensure top performance
selected Riding Mode (Power Mode), but even to for track use.
accurately control the engine brake (EBC), thereby
helping to control the rear wheel slipping (DTC).
Ducati Quick Shift (DQS)
The Ducati Quick Shift (DQS) is the electronic shifter
Ducati Traction Control (DTC)
control system used for racing purposes that allows
The Ducati Traction Control system (DTC) supervises the rider to shift up under acceleration without using
the rear wheel slipping control and settings vary

27
the clutch and keeping the throttle open: this results
in lower shifting time and hence faster lap time.
Ducati Data Analyzer+ (DDA+)
DDA+ is the latest generation of the Ducati Data
Analyzer, with built-in GPS signal to create a "virtual
finish line". The system automatically detects lap end
and stops the lap timer, without the rider needing to
do anything. Thanks to the built-in GPS signal, it also
shows the trajectories on track map and the key
motorcycle parameters: throttle opening, speed,
rpm, gear engaged, engine temperature, DTC
intervention.

28
Function push-buttons 3
1) UP CONTROL SWITCH " "
Button used to display and set instrument panel
parameters with the position " ".
2) DOWN CONTROL SWITCH " "
Button used to display and set instrument panel
parameters with the position " ".
3) HIGH-BEAM FLASH BUTTON (FLASH)
The high-beam flash button may also be used for LAP
functions.
4) TURN INDICATORS CANCEL BUTTON
The turn indicators cancel button may also be used 1
for the CONFIRM MENU function, for selecting the 3
riding style. Press this button for 3 seconds to the left
side to activate the HAZARD function (all 4 turn
indicators).

2
Fig. 4
29
How to set/display parameters
Upon start, the instrument panel:
- turns on the display backlighting;
- turns on all its elements at the same time;
- turns the engine rpm bargraph ON and OFF
progressively;
- displays all available speed values progressively
from the minimum to the maximum one and vice
versa;
- it turns on the LED warning lights in three steps

("initial check").
At the end of the "initial check" the instrument panel
displays the main screen called "Standard screen".

Fig. 5
30
During the first check stage, if the motorcycle speed
exceeds 10 km/h (actual speed), the instrument panel
will stop:
- the display check routine and display the
Standard screen containing updated information;
- the warning light check routine and leave ON only
the warning lights that are actually active at the
moment.

Note
When turning the key to OFF, motorcycle
power is cut only after 70 seconds and not
immediately.

31
Data displayed on the main screen are as follows:
1) Rpm bargraph.
2) Motorcycle speed.
3) Gear engaged.
4) MENU 1 (Odometer, Trip 1, Trip 2, Trip Fuel,
Trip Time, Clock, Lap time - only if active).
5) MENU 2 (Ambient air temperature,
Instantaneous fuel consumption, Average fuel
consumption, Average speed, Trip time).
6) Engine coolant temperature.
7) Set Riding Mode.
8) DTC level indication (ON) or DTC OFF
indication.
9) EBC level indication (ON) or EBC OFF
indication.
10) ABS ON/OFF indication.
11) "DQS ON" indication or "DQS OFF" indication.
12) "DDA ON" indication.
13) "GPS receiving" indication (if fitted).
14) "LAP ON" indication (if fitted).

32
 13 7 2 1

14
12
11

10
8

4 6 5 9

Fig. 6

33
Press button (1) to display MENU 1 information.
1
The data displayed in a sequence are:
- Odometer (TOT);
- TRIP A;
- TRIP B;
- TRIP FUEL (when function is active);
- Trip time (TRIP TIME).
- Clock;
- Lap time (when LAP function is active).

Fig. 7
34
Press button (2) to display MENU 2 information.
The data displayed in a sequence are:
- Air temperature;
- Instantaneous fuel consumption (CONS.);
- Average Fuel Consumption (CONS. AVG);
- Average speed (SPEED AVG);

Fig. 8
35
Upon Key-ON, the data displayed for MENU 1 and
MENU 2 are the ones displayed upon the previous
Key-OFF.

Note
The factory set default parameter (Odometer -
TOT) is displayed for 10 seconds upon Key-ON for
MENU 1 and then the parameter from last Key-OFF
is displayed.

Note 2
In case of sudden and unexpected power OFF,
Fig. 9
the instrument panel displays the default settings
upon the following Key-ON; in particular:
- for MENU 1 - Odometer (TOT); Important
- for MENU 2 - Air temperature. The SETTING MENU can only be opened if
motorcycle actual speed is lower than or equal to 20
When the Standard screen is displayed, hold the km/h. When the SETTING MENU is open and
button (2) for 3 seconds, when actual motorcycle motorcycle actual speed exceeds 20 km/h, the
speed is lower than or equal to 20 km/h, to enter the instrument panel automatically closes it and displays
SETTING MENU, where you can set any function. the Standard screen.

36
If the key is not acknowledged upon Key-ON and
once the starting check routine is over, the following
will happen:
- if the PIN CODE function is not active, the
instrument panel performs the initial check,
displays the Standard screen with an E-LOCK
error warning and does not allow accessing the
SETTING MENU, except for the Error page
(ERR);
- if the PIN CODE function is active, the PIN CODE
function page is displayed on the instrument
panel, allowing rider to enter the release code.
Fig. 10

37
Main functions Auxiliary functions
The functions displayed in the Standard screen are
the following: - DDA (only if present)
- GPS (only if present)
- Engine rpm indication (RPM) - (CLOCK)
- Motorcycle speed - Service indication (SERVICE)
- Gear - "ERROR" indication
- Riding Mode
- DTC
- EBC
- DQS
- ABS
- Engine Coolant temperature
- MENU 1 displays the following functions:
- Odometer (TOT)
- Trip meter 1 (TRIP A)
- Trip meter 2 (TRIP B)
- Partial fuel reserve counter (TRIP FUEL)
- Trip time (TRIP TIME)
- Clock
- LAP time - only if active
- MENU 2 displays the following functions:
- Ambient air temperature
- Instantaneous fuel consumption (CONS.)
- Average Fuel Consumption (CONS. AVG)
- Average speed (SPEED AVG)

38
The functions within the SETTING MENU that can be
modified by the user are the following:
- Customising Riding Modes (R.M.): within this
menu, rider can customise the following:
- EBC level setting (EBC)
- DTC level setting (DTC)
- DQS ON/OFF (DQS)
- ABS setting (ABS)
- Engine setting (ENGINE)
- Reset to default settings (DEFAULT)
- Battery voltage - BATTERY (BAT.)
- Display backlighting - BACK LIGHT (B.L.)
- LAP (view/delete/reset automatic settings)
- DDA (ON/OFF - view - delete)
- Clock settings - CLOCK SETTING (CLK)
- PIN CODE enter/change (PIN)
- Engine rpm digital indication (RPM)
- Unit setting (Speed - Temperature - Fuel
consumption) UNIT
- Error display - only if active errors are present
(ERR.)

39
Engine rpm indicator (RPM)
B B
The instrument panel receives the engine rpm A A
information and displays it on the relevant bargraph.
The information is displayed by the bargraph filling
from the left to the right according to the engine rpm
and with the negative display (switching OFF of the
digit and switching on of its rectangle) of the
numerical digit of the relevant miles.
When reaching 12,000 rpm no numerical digit must
be displayed in negative.
The rev limiter thresholds indicated by the red
warning light switching on are:
1st threshold 10,500 rpm (A).
2nd threshold 10,900 rpm (B).

Fig. 11
40
Motorcycle speed
A
The instrument panel receives information about the
actual motorcycle speed (calculated in km/h) and B
displays the value increased by 5% and converted in
the set unit of measurement (km/h or mph).
A string of dashes "- - -" is displayed with the set unit
of measurement if:
- speed is e qual to 299 km/h or 186 mph or if
instrument panel is not receiving the speed value
("- - -" steady ON);
- the rear speed sensor is in fault (flashing "- - -",
EOBD warning light (A) ON, WARNING symbol Fig. 12
(B) and SPEED error display).

41
Gear
A
The instrument panel receives information about the
gear engaged and displays the corresponding value. B
If a gear is engaged, the displayed value may range
from "1" to "6", while if in neutral "N" is displayed. C
Letter "C" is displayed when system requires you to
shift gear.
A string of dashes "- -" is displayed if:
- gear teach-in has not been carried out yet ("- -"
flashing and Neutral light (A) blinking);
- the gear sensor is in fault (flashing "- -", EOBD
warning light (B) ON, WARNING symbol (C) and
Fig. 13
GEAR error display);
- the instrument panel is not receiving the gear
data ("--" steady ON).

42
Gear sensor learning
During the gear learning procedure to be performed
on the motorcycle the operator is guided by the
displayed information.
The instrument panel indicates the saved gear and
prompts the operator to proceed with the next gear.
When the instrument panel displays letter "C" instead
of the gear number and switches Neutral "N" warning
light on, both flashing quickly, it is necessary to shift
gear.

Fig. 14

43
Riding Mode Selecting the Riding Mode
The Riding Mode can be selected from the Press CONFIRM MENU button (4) to enter the menu
instrument panel. Pre-set riding modes are three: for selecting the Riding Mode. The instrument panel
RACE, SPORT, WET. displays the name of the Riding Modes in the
The selected and active riding mode is displayed on Standard screen:
the Standard screen of the instrument panel.
Every Riding Mode contains the following - RACE
parameters, set by Ducati or customised by the user - SPORT
through the setting function pages: - WET
- a specific level of intervention for the DTC One of them will be marked with an arrow near its
traction control (1, 2, 3, 4, 5, 6, 7, 8, OFF); name to indicate the last memorised condition that is
- a specific engine power that will change throttle currently active.
behaviour (HIGH, MED, LOW);
- a specific ABS calibration (1, 2, 3, OFF);
- a specific level of intervention of the EBC engine
Warning
It is not possible to open the menu for selecting
brake control system (1, 2, 3, OFF);
the riding mode, if button (4) is in the position for
- the activation or deactivation of the quick shifter
activating the turn indicators (to the left or right).
DQS (DQS ON or DQS OFF).
The stored settings may be the factory ones (Ducati
Warning default settings) or the ones customised by the
Ducati recommends changing the Riding mode owner. Every time the MENU CONFIRMATION
when the motorcycle is stopped. If the riding mode button (4) is pressed, the instrument panel highlights
is changed while riding, be very careful (it is in sequence the riding modes.
recommended to change the Riding mode at a low Once the desired riding mode is highlighted, confirm
speed). the selection by holding down the CONFIRM MENU

44
button (4) for 2 seconds: the new riding mode
4
selection is stored and the Standard screen is
displayed.
Once the desired riding mode is highlighted, if the
CONFIRM MENU button (4) is not pressed within 10
seconds, the new riding mode selection is not stored
and the Standard screen is displayed.

4 4

4 4 4

Fig. 15
45
When system requests rider to confirm the riding
mode change, the procedure will output an error if:
- the throttle twistgrip is open, brakes are
activated and the motorcycle is not still; in this
case "CLOSE GAS" and "DON’T BRK" warnings
flash on the display in MENU 1 and MENU 2, by
alternating each writing every second.
If within 5 seconds the throttle is not closed, the
brakes are not released or the motorcycle is not
stopped (zero speed), the procedure for changing
riding mode will not be completed and the
Standard screen is displayed.

Fig. 16
46
 Note
If the change of riding mode is associated with
the ABS change of state from "ON" to "OFF" or vice-
versa, the instrument panel also starts the procedure
for disabling or activating the ABS, respectively, upon
confirmation of the selected riding mode.

Note
If at least one error is present upon Riding Mode
change, priority is given to messages "CLOSE GAS"
and "DON’T BRK", and the relevant Warning symbol
will flash.

47
DTC
The instrument panel displays DTC status as follows:
- if DTC is active, the "DTC" and the rectangle with
the Traction Control intervention level number (1
to 8);
- if DTC is not active, the message "DTC" and the
rectangle with the steady symbol "- -";
- if DTC or the Black Box control unit features an
error, the message "DTC" with the rectangle with
the flashing symbol "- -"; the EOBD warning light
turns on together with the warning symbol and
the relevant error is displayed.
Fig. 17

Fig. 18
48
 Warning
DTC is a rider aid that can be used both on the
track and the road. The system is designed to make
riding easier and to enhance safety, but in no way
relieves the rider of the obligation to drive responsibly
and to maintain a high standard of riding in order to
avoid accidents, whether caused by his own errors or
those of other road users, through making
emergency manoeuvres, in accordance with the
prescriptions of the road traffic code.

The rider must always be aware that active safety

systems have a preventive function. The active
elements help the rider control the motorcycle,
making it as easy and safe to ride as possible. The
presence of an active safety system should not
encourage the rider to ride at speeds beyond the
reasonable limits, not in accordance with the road
conditions, the laws of physics, good riding standards
and the requirements of the road traffic code.
The following table indicates the most suitable level
of DTC intervention for the various riding modes as
well as the default settings in the "Riding Mode" that
can be selected by the rider.

49
 DTC RIDING MODE USE DEFAULT
1 RACE Track use, for very expert riders, opti- NO
mised for Pirelli tyres with SC2 com-
pound. System permits sliding side-
ways.
2 RACE Track use, for very expert riders, opti- It is the default level for the
mised for OEM tyres (Original Equip- "RACE" Riding Mode
ment Manufacturer). Permits sliding
sideways.
3 RACE Track use for expert riders. Permits slid- NO
ing sideways.
4 RACE Track use (and road use for expert rid- NO
ers).
5 SPORT Sport style on the road or on the track, It is the default level for the
consistent with ENGINE 145 HP LOW "SPORT" Riding Mode
setting (maximum power 145 HP, with
Smooth delivery).
6 SPORT "Very safe" style on dry surface, on the NO
road or on the track, consistent with EN-
GINE 145 HP LOW setting (maximum
power HP, with Smooth delivery).

50
DTC RIDING MODE USE DEFAULT
7 WET (RAIN) Track use, with rain tyres, in particular it NO
was optimised for Pirelli Diablo Rain
tyres (rear tyre 190/60 ZR17).
8 WET (HEAVY Wet road and slippery asphalt with OEM It is the default level for the
RAIN) tyres; it must be associated with EN- "WET" Riding Mode
GINE 100 setting.

51
Tips on how to select the sensitivity level Warning
The DTC levels 2-3-4-5-6-8 settings have been
calibrated using the tyres originally supplied with your
Warning motorcycle (Pirelli Diablo Rosso Corsa: 120/70ZR17
The DTC level 1 setting has been calibrated at the front and 180/60ZR17 at the rear). The use of
using the tyres with SC2 compound (Pirelli Diablo tyres of different size and characteristics to the
Supercorsa SC2) that are not those originally supplied original tyres may alter the operating characteristics
with your motorcycle. The use of this level with tyres of the system.
having different characteristics may alter the
operating characteristics of the system. In the case of minor differences, such as for example,
tyres of a different make and/or model than the OE
Warning ones, but with the same size (rear = 180/60ZR17;
The DTC level 7 setting has been calibrated front = 120/70 ZR17), it may be sufficient to simply
using Rain tyres (Pirelli Diablo Rain with size 190/60 select the suitable level setting from those available
ZR17 at the rear) that are not those originally supplied in order to restore optimal system operation.
with your motorcycle. The use of this level with tyres If tyres of a different size class are used or if the tyre
having different characteristics may alter the dimensions differ significantly from the original tyres,
operating characteristics of the system. it may be that the system operation is affected to the
point where none of the 8 available level settings will
give satisfactory results. In this case it is advisable to
deactivate the traction control system.
If level 8 is selected, the DTC system will kick in at
the slightest hint that the rear wheel is starting to
spin. Between level 8 and level 1 there are further
intermediate levels of intervention for the DTC.
Levels 1, 2 and 3 allow the rear wheel to spin and

52
slide: these levels are recommended on the track The relation of the DTC intervention level to riding
only and exclusively for expert riders: in particular, mode: the DTC will tend to kick in more with a
level 1 is designed to work at best only with tyres "smooth" riding mode, where the motorcycle is
having SC2 compound. leaned over further, rather than with a "rough" style,
The choice of the correct level mainly depends on the where the motorcycle is straightened up as quickly
following parameters: as possible when exiting a turn.
- The tyre/asphalt grip (type of tyre, amount of tyre Tips for use on the track
wear, the road/track surface, weather conditions,
etc.). We recommend that level 6 is used for a couple of
- The characteristics of the path/circuit (bends all full laps (to allow the tyres to warm up) in order to get
taken at similar speeds or at very different used to the system. Then try levels 5, 4, etc., in
speeds). succession until you identify the DTC sensitivity level
- The riding mode (whether the rider has a that suits you best (always try each level for at least
"smooth" or a "rough" style). two laps to allow the tyres to warm up).
Once you have found a satisfactory setting for all the
Level depends on grip conditions: the choice of level corners except one or two slow ones, where the
setting depends greatly on the grip conditions of the system tends to kick in and control too much, you can
track/circuit (see below, tips for use on the track and try to modify your riding style slightly to a more
on the road). "rough" approach to cornering i.e. straighten up more
Level depends on type of track: if the track/path rapidly on exiting the corner, instead of immediately
features bends all taken at similar speeds, it will be trying a different level setting.
easier to find a level suitable for all bends; while a Tips for use on the road
track/path with bends all requiring different speeds
will require a DTC level setting that is the best Activate the DTC, select level 6 and ride the
compromise for all bends. motorcycle in your usual style; if the level of DTC
sensitivity seems excessive, try reducing the setting

53
to level 5, 4, etc., until you find the level that suits you
best.
If changes occur in the grip conditions and/or circuit
characteristics and/or your riding style, and the level
setting is no longer suitable, switch to the next level
up or down and proceed to determine the best
setting (e.g. if with level 5 the DTC intervention
seems excessive, switch to level 4; alternatively, if on
level 5 you cannot perceive any DTC intervention,
switch to level 6).

54
EBC
The instrument panel displays EBC status as follows:
- if EBC system is active, the message "EBC" and
the rectangle with the set intervention level
number (1 to 3);
- if EBC system is not active, the message "EBC"
and the rectangle with the steady symbol "- -";
- if EBC system or the control unit features an
error, the message "EBC" with the rectangle with
the flashing symbol "- -"; the EOBD warning light
turns on together with the Warning symbol and
the relevant error is displayed.
Fig. 19

Fig. 20
55
The EBC is a system controlling the engine brake
while riding with throttle fully closed (both when
downshifting and when simply releasing throttle with
the same gear engaged, and both under braking or
not), this system independently sets the throttles in
order to make the torque transmitted backward from
wheel to engine constant during these stages.
The system can be set on three different levels, from
the setting with less engine brake (level 3) to that with
a stronger braking (level 1).
The EBC can also be disabled (level OFF); in this
configuration no torque is transmitted backward.

Warning
EBC is a rider aid that can be used both on the
track and the road. The system is designed to make
riding easier, but in no way relieves the rider of the
obligation to ride responsibly and to maintain a high
standard of riding in order to avoid accidents, whether
caused by his own errors or those of other road users,
through making emergency manoeuvres, in
accordance with the prescriptions of the road traffic
code.

56
The following table indicates the most suitable level of EBC intervention for the various riding types as well
as the default settings in the "Riding Mode" that can be selected by the rider:

EBC CHARACTERISTIC DEFAULT

OFF Maximum engine brake NO
1 Quite important engine brake, but less than that It is the default level for all Riding
obtained with EBC OFF Modes
2 Very low engine brake, recommended only for NO
track use and for riders requiring a low engine
brake when decelerating
3 Minimum engine brake, recommended only for NO
track use and for riders preferring a very low engine
brake when decelerating

57
Tips on how to select the sensitivity level level 1 the engine brake is increasing progressively;
with EBC OFF you set the maximum engine brake
possible.
Warning
The choice of the correct level mainly depends on the
The EBC levels 1-2-3 settings have been
following parameters:
calibrated using the tyres originally supplied with your
motorcycle (Pirelli Diablo Rosso Corsa: 120/70ZR17 - The tyre/asphalt grip (type of tyre, amount of tyre
at the front and 180/60ZR17 at the rear). The use of wear, the road/track surface, weather conditions,
tyres of different size and characteristics to the etc.).
original tyres (in particular at the rear) may alter the - The characteristics of the path/circuit (bends all
operating characteristics of the system. taken at similar speeds or at very different
speeds).
In the case of minor differences, such as for example, - The Riding Mode.
tyres of a different make and/or model than the OE - Level depends on grip conditions: the choice of
ones, but with the same size (rear = 180/60 ZR17; level setting depends greatly on the grip
front = 120/70 ZR17), it may be sufficient to simply conditions of the track/circuit (see below, tips for
select the suitable level setting from those available use on the track and on the road).
in order to restore optimal system operation. - Level depends on type of track: if the track/path
If tyres of a different size class are used or if the tyre requires consistent braking (always aggressive
dimensions differ significantly from the original tyres, or always smooth), it will be easier to find a level
it may be that the system operation is affected to the suitable for all braking instances; while a track/
point where none of the 3 available level settings will path requiring different braking power will
give satisfactory results. In this case it is advisable to require an EBC level setting that is the best
deactivate the traction control system. compromise for all instances.
Selecting level 3, the EBC will kick in to ensure the
minimum engine brake possible. Between level 3 and

58
DQS
The instrument panel displays DQS status as follows:
- if the DQS system is active, the message "DQS"
and the relevant box;
- if DQS or the control unit is in fault, the EOBD
turns on together with the Warning symbol and
the corresponding error is displayed.

Fig. 21

Fig. 22
59
ABS
The motorcycle is equipped with ABS, the instrument
panel displays the rectangle with ABS status.
The instrument panel displays:
- if the ABS is active, the message "ABS" and the
rectangle with the set intervention level number
(1 to 3);
- if the ABS is not active, the message "ABS" and
the rectangle with the steady symbol "- -";
- if the ABS is in fault, the message "ABS" and the
rectangle with the flashing symbol "- -"; the EOBD
warning light turns on together with the Warning
Fig. 23
symbol and the corresponding error is displayed.

If the instrument panel does not receive information,

the ABS warning light turns on.

Fig. 24
60
The following table indicates the most suitable level of ABS intervention for the various riding types as well
as the default settings in the "Riding Mode" that can be selected by the rider:

ABS RIDING MODE CHARACTERISTIC DEFAULT

OFF The ABS is disabled NO
1 RACE Exclusively for track use, for expert riders It is the default level for the
(not recommended for road use). The ABS "RACE" Riding Mode
in this mode only works on the front wheel
(preventing it from locking), while there is
no control on the rear wheel; the system
does NOT control lift-up.
2 ROAD For road use in good grip conditions, both It is the default level for the
wheels are controlled by the system; anti "SPORT" Riding Mode
lift-up control is active but this setting most-
ly focuses on braking power and allows a
few uncontrolled lift-ups.
3 WET CONDITION ROAD/ For use under any wet condition, system It is the default level for the
TRACK controls both wheels; the system controls "WET" Riding Mode
most of the lift-ups.

61
Tips on how to select the sensitivity level motorcycle keeps a good alignment during the whole
braking. Settings between level 3 and level 1 privilege
more and more the braking power rather than stability
Warning and lift-up control; level 1 provides no lift-up control,
The ABS levels 1-2-3 settings have been the rear brake is not controlled by the ABS.
calibrated using the tyres originally supplied with your
The choice of the correct level mainly depends on the
motorcycle (Pirelli Diablo Rosso Corsa: 120/70ZR17
following parameters:
at the front and 180/60ZR17 at the rear). The use of
tyres of different size and characteristics to the 1) The tyre/asphalt grip (type of tyre, amount of tyre
original tyres (in particular at the rear) may alter the wear, the road/track surface, weather conditions,
operating characteristics of the system. etc.).
2) The rider's experience and sensitivity: expert
In the case of minor differences, such as for example, riders can tackle a lift-up in trying to reduce the
tyres of a different make and/or model than the OE stopping distance to a minimum, while less
ones, but with the same size (rear = 180/60 ZR17; expert riders are recommended to use settings
front = 120/70 ZR17), it may be sufficient to simply 2 and 3, that will help them keeping the
select the suitable level setting from those available motorcycle more stable even in emergency
in order to restore optimal system operation. braking.
If tyres of a different size class are used or if the tyre
dimensions differ significantly from the original tyres, Engine coolant temperature
it may be that the system operation is affected to the The instrument panel receives information about the
point where none of the 3 available level settings will engine temperature (already calculated in °C) and
give satisfactory results. In this case it is advisable to displays the value in the set unit of measurement (°C
deactivate the traction control system. or °F), followed by the unit of measurement and the
Selecting level 3, the ABS will intervene to ensure a engine temperature symbol.
very stable braking, good lift-up control, the

62
The temperature display range goes from 40 °C to
+120 °C.
If reading is:
- <= (lower than or equal to) -40 °C, a string of
flashing dashes " - - - " is displayed;
- within the range -39 °C to +39 °C, "LO" is
displayed steadily;
- within the range +40 °C to +120 °C, the value is
displayed steadily;
- >= (higher than or equal to) +121 °C, "HI" is
displayed flashing.

If the coolant temperature sensor is in fault, a string

of flashing dashes "- - -" is displayed, followed by the
set unit of measurement; the EOBD light turns on
together with the Warning symbol and the ENG. error
is displayed.
If the instrument panel is not receiving coolant
temperature value, a string of steady dashes "- - -" is
displayed, followed by the unit of measurement.

63
 Fig. 25

64
Menu 1 functions 1
MENU 1 functions are:
- Odometer (TOT);
- Trip meter 1 (TRIP A);
- Trip meter 2 (TRIP B);
- Partial fuel reserve counter (TRIP FUEL);
- Trip time (TRIP TIME);
- Clock;
- LAP time (if active). 1

By pressing button (1) it is possible to view the

functions of MENU 1.

Fig. 26
65
Menu 1: Odometer (TOT)
The odometer counts and displays the total distance
covered by the motorcycle with the set unit of
measurement (km or mi).
The odometer number (in km or miles) is displayed
with the message "TOT" and the indication of the unit
of measurement. When the maximum value is
reached (199999 km or 199999 mi) the instrument
panel will permanently display said value.
The odometer value is saved permanently and cannot
be reset under any circumstances. The reading is not
lost in case of a power OFF (Battery OFF).

Note
Upon Key-ON, the instrument panel always
shows the message "Odometer" for 10 seconds, then
shows the user's settings page.

Fig. 27
66
 Note
If a string of flashing dashes " ----- " is displayed
within odometer function, please contact a Ducati
Dealer or Authorised Service Centre.

67
Menu 1: Trip meter 1 (TRIP A) 1
The trip meter counts and displays the partial distance
covered by the motorcycle with the set unit of
measurement (km or mi) and is used as a basis to
calculate average fuel consumption, average speed
and trip time. The number (in km or miles) is displayed
with the message "TRIP A" and unit of measurement.
When the reading exceeds the maximum value of
9999.9 km or 9999.9 mi, distance travelled is reset
and the meter automatically starts counting from 0
again.
While the trip meter is displayed, press button (1) for
3 seconds to reset TRIP A. When TRIP A is reset, the
average fuel consumption, average speed and trip
time data are reset as well.
The TRIP A counter is automatically reset in case the
system unit of measurement is changed manually:
the counter will then start back from zero, considering
the new units of measurement.

Fig. 28
68
Menu 1: Trip meter 1 (TRIP B) 1
The trip meter counts and displays the partial distance
covered by the motorcycle with the set unit of
measurement (km or mi).
The number (in km or miles) is displayed with the
message "TRIP B" and unit of measurement.
When the reading exceeds the maximum value of
9999.9 km or 9999.9 mi, distance travelled is reset
and the meter automatically starts counting from 0
again.
While the trip meter is displayed, press button (1) for
3 seconds to reset TRIP B.
The TRIP B counter is automatically reset in case the
system unit of measurement is changed manually:
the counter will then start back from zero, considering
the new units of measurement.

Fig. 29
69
Menu 1: Partial fuel reserve counter (TRIP A
FUEL)
The fuel trip meter counts and displays the distance
covered by the motorcycle on reserve (since the low
fuel light turns on) with the set unit of measurement
(km or mi). When the Low fuel light (A) turns on, the
display automatically shows the TRIP FUEL function,
regardless of the currently displayed function; then,
it is possible to toggle through the other Menu
functions. Trip fuel reading remains stored even after
Key-OFF until the motorcycle is refuelled. Count is
interrupted automatically as soon as fuel is topped up
to above minimum level. The number (km or miles) is
displayed with the message "TRIP FUEL" and the
indication of the unit of measurement. When the
reading exceeds the maximum value of 9999.9 km or
9999.9 mi, distance travelled is reset and the meter
automatically starts counting from 0 again. When the
TRIP FUEL function is not active, the corresponding
value will not be displayed in the Menu.

Fig. 30
70
MENU 1: Trip time
The instrument panel calculates and displays the trip
time as "hhh:mm" followed by TRIP TIME.
The calculation considers the time since TRIP A was
last reset. When TRIP A is reset, this value is reset as
well.
The time count active phase occurs when the engine
is running and the motorcycle is stopped (the time is
automatically stopped when the motorcycle is not
moving and the engine is OFF and restarts when the
counting active phase starts again).
When the reading exceeds "720:00" (720 hours and
00 minutes), the meter is reset and automatically
starts counting from 0 again.

Note
If you change the unit of measurement for an
item connected to Speed (and distance) or
Consumption, the trip time value will be automatically
reset.

Fig. 31
71
MENU 1: Clock
The instrument panel receives information about the
time to be displayed.
The time indication is displayed in MENU 1.
The instrument panel shows the time in the following
format:
- hh (hours) : mm (minutes)

with the message "AM" (for values ranging between

0:00 and 11:59), or "PM" (for values ranging between
12:00 and 12:59 and between 1:00 and 11:59).
If the instrument panel does not receive current time
information, it displays "- - : - - AM" steadily.

Fig. 32
72
Menu 1: Lap time (LAP time) 3
LAP function information is available when the
function is active. After the LAP function activation
from the SETTING MENU, when going back to the
Standard screen the LAP function is automatically
displayed as first page of MENU 1 and the messages
"TIME" and "LAP" are displayed respectively in MENU
1 and on the display. Then it is possible to scroll the
other functions of MENU 1. Upon LAP function
activation, the display shows the timer starting from
"0’00’’00" .
When the FLASH button (3) is pressed for the first
time, or upon an equivalent command (optional GPS),
the timer starts with resolution of a tenth of a second 3
("0’00’’0"). Every time the FLASH button (3) is
pressed again, or upon an equivalent command
(optional GPS) the display temporarily shows the
number and time of the just-ended lap, then it will
show the timer and number of the new current lap.

Fig. 33
73
If the motorcycle is equipped with GPS, the lap "Start/
3
Stop" command is sent by the GPS. In order for the
GPS to identify each lap's "Start/Stop" automatically,
the user must store the finish line coordinates by
pressing the FLASH button (3) when passing the
finish line for the first time. Upon storage the
message "GPS" will flash quickly and then return
steady.
Stored finish line coordinates are retained after Key-
OFF and remain valid if the stored GPS finish line is
within a range of 15 km from the current position,
whereas they are updated each time FLASH button
(3) is pressed while the LAP function is active. If a
stored finish line is stored anew, the message "GPS"
will flash quickly and then return steady.

Fig. 34
74
If lap timer is active but motorcycle is at standstill, lap - When the FLASH button (3) is pressed for the
timer is temporarily stopped after 5 seconds and it is first time, or upon an equivalent command
displayed with the initial indication "0’00’’00". the next (optional GPS), the instrument panel displays the
time rider pushes the FLASH button (3) or any timer with resolution of a tenth of a second
equivalent command (optional GPS), lap timer is ("0’00’’0");
reactivated. - the next times the FLASH button (3) is pressed,
or after an equivalent control (optional GPS), the
Note instrument panel displays for 5 seconds the just-
When the LAP function is active, the FLASH ended lap time with a resolution of a hundredth
button takes on the dual function of high beam of a second;
"FLASH" and LAP timer start / stop (new lap start - after these 5 seconds, the instrument panel goes
indication). back to lap timer page referred to the new current
lap.
- if motorcycle remains at standstill for over 5
Note seconds, lap timer is temporarily stopped and it
The TRIP FUEL function always has top priority is displayed with the initial indication "0’00’’00";
over the LAP function: in case of activation of the - the next time rider pushes the FLASH button (3)
TRIP FUEL function with active LAP function, the LAP or any equivalent command (optional GPS), lap
timer view is automatically removed and TRIP FUEL timer is reactivated.
information is displayed instead.
If the time is never stopped, it will roll over upon
LAP recording reaching 9 minutes, 59 seconds and 99 hundredths;
If the LAP function is active, it is possible to record the lap timer starts counting from zero and will keep
the lap time, for a total of 30 consecutive laps. running until the lap is stopped or the recording
Operation: function is disabled.

75
Laps are numbered from 01 to 30 and are in a loop:
after the first 30 laps the instrument panel will
overwrite information starting from Lap 01.
If the LAP function is interrupted and then reactivated
but memorised laps are not deleted, lap information
will be recorded by overwriting data of the oldest Lap.
Example: if you rode 34 laps without deleting data,
the instrument panel stores the first 30 laps and then
overwrites the first 4 laps. Upon the following Key-
ON or reactivation of the LAP function, if no data were
deleted, the instrument panel will continue storing
data from Lap 05.
During every lap, the following data are stored:
- no. 30 lap times (time between consecutive start
and stop);
- no. 30 values for max. RPM (maximum RPM
value reached in every lap);
- no. 30 values for max. speed (maximum speed
value reached in every lap).

76
MENU 2 functions
MENU 2 functions are:
- Ambient air temperature
- Instantaneous fuel consumption (CONS.)
- Average Fuel Consumption (CONS. AVG)
- Average speed (SPEED AVG)
2
By pressing button (2) it is possible to view the
2
functions of MENU 2.

Fig. 35
77
MENU 2: Air temperature
The instrument panel displays the ambient
temperature in the set unit of measurement (°C or
°F), followed by the set unit of measurement and the
message "T-AIR". The temperature value is displayed
when ranging from -39 °C to +124 °C (or -38 °F ÷
+255 °F). For any different temperature (below -39 °C
or above +124 °C) a string of three dashes " - - - " is
steadily displayed, followed by the unit of
measurement.
If the air temperature sensor is in fault, the
instrument panel will show three flashing dashes " - -
- " as air temperature value, followed by the unit of
measurement, the EOBD light will turn on together
with the Warning symbol and the corresponding error
(ENG) is displayed.
If the instrument panel is not receiving air
temperature value, a string of three steady dashes "-
- -" is displayed, followed by the unit of measurement.

Note
When the motorcycle is stopped, the engine
heat could influence the displayed temperature.

Fig. 36
78
MENU 2: Instantaneous fuel consumption
The instrument panel calculates and displays the
motorcycle instantaneous fuel consumption, the set
unit of measurement and CONS. text.
The calculation is made considering the quantity of
fuel used and the distance travelled during the last
second. Value is expressed in the set unit of
measurement: litres / 100 km or mpg UK or mpg USA.
The active calculation phase only occurs when the
engine is running and the motorcycle is moving
(moments when the motorcycle is not moving when
speed is equal to 0 and/or when the engine is OFF
are not considered). When the calculation is not
made, a string of three dashes is displayed " - - . - "
steadily as instantaneous fuel consumption.

Note
It is possible to change the units of
measurement for "Consumption" (both average and
instantaneous together) from L/100 to km/L through
the SETTING MENU, using the UNITS SETTING
function.

Fig. 37
79
MENU 2: Average fuel consumption
The instrument panel calculates and displays the
motorcycle average fuel consumption, the set unit of
measurement and CONS. AVG text. The calculation
is made considering the quantity of fuel used and the
distance travelled since TRIP A was last reset. When
TRIP A is reset, the value is reset and the first value
available is displayed 10 seconds after the reset.
During the first 10 seconds, when the value is not yet
available, the display will show a string of three
dashes "- - . - " steadily as average fuel consumption.
Value is expressed in the set unit of measurement
(litres / 100 km or mpg UK or mpg USA). The active
calculation phase occurs when the engine is running
and the motorcycle is stopped: moments when the
motorcycle is not moving and the engine is OFF are
not considered.

Note
It is possible to change the units of
measurement for "Consumption" (both average and
instantaneous together) from L/100 to km/L through
the SETTING MENU, using the UNITS SETTING
function.

Fig. 38
80
MENU 2: Average speed
The instrument panel calculates and displays the
motorcycle average speed, the set unit of
measurement and SPEED AVG text. The calculation
considers the distance and time since Trip A was last
reset. When TRIP A is reset, the value is reset and
the first value available is displayed 10 seconds after
the reset. During the first 10 seconds, when the value
is not yet available, the display will show a string of
three dashes " - - - " steadily as average speed. The
active calculation phase occurs when the engine is
running and the motorcycle is stopped (moments
when the motorcycle is not moving and the engine is
OFF are not considered). The average speed value
displayed is calculated by adding 5% so as to be
consistent with motorcycle speed indication.

Note
It is possible to change the units of
measurement of Speed (and distance travelled as
well) from km/h (and km) to mph (and mi) through the
SETTING MENU, using the UNITS SETTING function.

Fig. 39
81
Auxiliary functions
DDA
The instrument panel indicates DDA status only if the
motorcycle fits the DDA.
If the message "DDA" is displayed it means that the
DDA is active and recording.
If the message "DDA" is not displayed it means that
the DDA is not active.

Fig. 40

82
GPS (optional)
3
The instrument panel provides the message "GPS"
only when the GPS (optional) fitted to the motorcycle
is present. The instrument panel displays the status
of the GPS receiver if it is installed on the motorcycle.
If the message "GPS" is displayed steady ON it means
that GPS location has been found and GPS reception
is active. If the message "GPS" is displayed flashing it
means that no GPS location has been found, or GPS
reception is not active or a GPS error has occurred. If
the message "GPS" is not displayed it means that the
GPS is not present.
Fig. 41
The GPS may also be used to determine finish line
location for the LAP function. When this is the case,
the "new lap start" command is sent by the GPS.
In order for the GPS to identify each lap's "Start/Stop"
automatically, finish line coordinates need to be
stored in the GPS. Coordinates must be stored when
the finish line is passed for the first time by pressing
the FLASH (3) button.

83
Service warning (SERVICE)
This indication shows the user that the motorcycle is
due for service and must be taken to a Ducati
Authorised Service Centre.
The service warning indication can be reset only by
the Authorised Ducati Service Centre during
servicing.
- OIL SERVICE = 12,000 km.
- DESMO SERVICE = 24,000 km.

Fig. 42

84
Zero OIL SERVICE warning
The first maintenance indication is "OIL SERVICE
zero", enabled when the odometer counter reaches
the first 1,000 km (600 miles).
The indication is the display for 5 seconds of the
flashing message "SERVICE", the Oil symbol and the
message "OIL" upon each Key-ON; after 5 seconds
both the message "SERVICE" and the Oil symbol
become steady until Key-OFF or until an Authorised
Ducati Service Centre performs a reset.

Fig. 43

85
The message "OIL SERVICE" or "DESMO A
SERVICE" countdown
After OIL SERVICE zero reset (at 1,000 km - 600
miles), the instrument panel activates the countdown
of the kilometres (or miles) left before the following
service operation: OIL SERVICE (A) or DESMO
SERVICE (B).
The kilometre count indication is shown upon Key-ON
for 2 seconds; when there are 1,000 km (600 miles)
left before the next service operation, the indication
turns on upon every Key-ON for 5 seconds.
In other words, upon Key-ON the message Fig. 44
"SERVICE" , the Oil and the Desmo symbol are
displayed together with the indication of the B
kilometres left before the following service operation.

Fig. 45
86
OIL SERVICE or DESMO SERVICE A
warning
When the service threshold is reached, the warning
for the type of service required is triggered: OIL
SERVICE (A) or DESMO SERVICE(B).
The indication is the display for 5 seconds of the
flashing message "SERVICE", the "OIL" or "DESMO"
symbol as well as the message "DESMO" upon each
Key-ON; after 5 seconds both the message
"SERVICE" and the Oil or Desmo symbol become
steady until Key-OFF or until an Authorised Ducati
Service Centre performs a Reset.
Fig. 46

Fig. 47
87
Errors
The instrument panel manages error warnings in
order to allow the rider to identify any abnormal
motorcycle behaviour in real time.
Upon Key-ON, if there are active errors the
instrument panel turns the EOBD light and Warning
symbol ON and activates the Error page of the
SETTING MENU. During standard motorcycle
operation, upon the activation of an error the
instrument panel turns the EOBD light and Warning
symbol ON and activates the Error page of the
SETTING MENU.
Fig. 48
To display the present errors enter the SETTING
MENU, use buttons (1) and (2) to select "ERR." (which
is the first available page in case of active errors) and 1
press button (4).
The instrument panel displays "ERR" steady ON and: 4
- the error type indication steady ON;
- the EXIT steady ON and its box flashing.

Fig. 49
88
If several active errors are present, the corresponding
indications will be displayed one after the other and
every one will stay ON for 3 seconds. When an error
is triggered the EOBD light turns on as well.

Warning
When one or more errors are displayed, always
contact a Ducati Dealer or authorised Service Centre.

89
Displayed error description
Displayed error Description
CAN LINE CAN line BUS OFF
UNK-D Control unit not acknowledged by the system - wrong SW
ABS ABS control unit faulty communication / operation
BBS BBS control unit faulty communication / operation
BBS control unit general malfunction
Exhaust valve motor malfunction
DSB DSB control unit faulty communication / operation
E-LOCK E-LOCK control unit faulty communication / operation
E-LOCK control unit general malfunction
(Immobilizer) key-antenna malfunction
ENG. ECU control unit faulty communication / operation
ECU control unit general malfunction
Throttle position sensor malfunction
Throttle grip position sensor malfunction
Throttle motor or relay malfunction
Pressure sensor malfunction
Engine coolant temperature sensor malfunction

90
Displayed error Description
Intake duct air temperature sensor malfunction
Injection relay malfunction
Ignition coil malfunction
Injector malfunction
Engine rpm sensor malfunction
Lambda sensor or Lambda sensor heater malfunction
motorcycle starting relay malfunction
Quick shift device switch malfunction
Secondary air sensor malfunction
GEAR Gear sensor malfunction
FUEL Reserve NTC sensor malfunction
SPEED Front and/or rear speed sensor malfunction
BATT. Battery voltage too high or too low
STOP Stop light not working
FAN Electric cooling fan malfunction
STAND Side stand sensor malfunction

91
 Note
The message "FAN" can be displayed also in case of BBS control unit malfunction and its faulty com-
munication with fans. Pay attention to engine temperature indication.

92
Error icons table
"WARNING LIGHT / ERROR" MESSAGE ERROR

BBS Black-Box control unit

ABS ABS control unit

DSB Instrument panel ctrl unit

E-LOCK E-LOCK control unit

ENG. ECU

CAN Can Bus OFF

UNK-D Software compatibility

FAN Cooling fan

BATT. Battery voltage

93
"WARNING LIGHT / ERROR" MESSAGE ERROR

STOP Rear stop light

STAND Side stand sensor

GEAR Gear sensor

SPEED Speed sensor

FUEL Low fuel sensor

Note
The message "FAN" can be displayed also in case of BBS control unit malfunction and its faulty com-
munication with fans. Pay attention to engine temperature indication.

94
Setting MENU Press buttons (1) and (2) to highlight the customisable
This menu allows enabling, disabling and setting parameters one by one: in particular, use button (1)
some motorcycle functions. to highlight the following item and button (2) to
To enter the SETTING MENU it is necessary to hold highlight the previous item.
button (2) for 3 seconds, with Key-ON and motorcycle After highlighting the required parameter, press
actual speed ≤ (lower than or equal to) 20 km/h: within button (4) to open the corresponding MENU page.
this menu, it is no longer possible to view any other If function is not available or temporarily disabled, the
function. MENU page can not be opened.
The SETTING MENU displays the following To quit the SETTING MENU you shall highlight "EXIT"
functions: and press CONFIRM MENU button 4.
- Riding mode (R.M.)
- Battery (BAT.)
Note
- Back light (B.L.) The messages "SETTING MENU" and "EXIT"
- LAP (LAP) remain always active in the SETTING MENU and its
- DDA (DDA) sub-menus.
- Clock (CLK)
- PIN code (PIN) Note
- RPM (RPM) When the SETTING MENU is active it is not
- Units setting (UNT) possible to scroll the other functions of MENUS 1 and
- Errors (ERR.) (only if active errors are present) 2.

Important Important
For safety reasons, it is recommended to use Each menu page usually indicates the selected
this Menu with the motorcycle at a standstill. functions by showing the relevant flashing value,
message and the box with the relevant information.

95
 2 2 2

1 1 1
2 1 1 2

2 1 1 2

2 1 1 2
1 1 1

2 2 2

Fig. 50

96
Customising Riding Modes
All settings of every riding mode can be customised. 1
Enter the SETTING MENU.
Select the R.M. (Riding mode) option by pressing 4
button (1) or (2). Once function is highlighted, press
CONFIRM MENU button (4). 2
Enter the R.M. (Riding mode) MENU.
After entering the function the display shows the
three available riding modes (RACE, SPORT or WET). 4
1
Press buttons (1) and (2) to select the riding mode to
1 1
be customised (the arrow beside flashes). Press
CONFIRM MENU button (4) to enter the
customisation of the selected Riding Mode.
While if you highlight "EXIT" and press button (4) you
quit the sub-menu and go back to previous page.
2 2
4 2

Fig. 51
97
The parameters that can be customised for every If you highlight "EXIT" and press button (4) you quit
riding mode are the following: the sub-menu and go back to previous page.
- ENGINE
- EBC Warning
- DTC Changes should only be made to the
- ABS parameters by people who are experts in motorcycle
- DQS set-up; if the parameters are changed accidentally,
- DEFAULT (to restore the parameters set by use the "DEFAULT" function to restore factory
Ducati for each riding mode) settings.

When entering the customisation menu of the

selected riding mode the ENGINE parameter is
automatically highlighted (the relevant parameter
flashes) and it is possible to scroll the menu items by
pressing buttons (1) and (2) to select all available
information (the selected parameter flashes) in the
following sequence:
- ENGINE
- EBC
- DTC
- ABS
- DQS
- MEMORY
- EXIT
- DEFAULT

98
 2 2

1 1

2 1 2
1

1 1 2
2
1 1
1

4
2 2
2

Fig. 52

99
Riding mode customisation: Storing Riding
Mode settings
It is possible to save the parameters set for each
riding mode.
To save the parameter settings of a Riding Mode it is
necessary to gain access to the SETTING MENU, use
buttons (1) and (2) to select the message "R.M." 4
(Riding Mode) and press button (4). Then use buttons
(1) and (2) to select the riding mode to change and
press button (4). Then use buttons (1) and (2) to select 2 1
"MEMORY" (flashing) and keep button (4) pressed for
2 seconds.
Any parameter change made is saved and remains in
the memory also after a Battery-OFF. If you highlight
"EXIT" and press button (4) you quit the sub-menu and
go back to previous page.

2
Fig. 53
100
 Warning
Changes should only be made to the
parameters by people who are experts in motorcycle
set-up; if the parameters are changed accidentally,
use the "DEFAULT" function to restore factory
settings.

101
Customising Riding Modes: EBC level confirm. The value will become automatically steady
and the message "EXIT" will be highlighted.
setting
To exit the menu and go back to previous page, select
This function disables or sets the rear wheel
"EXIT" and press button (4). The instrument panel will
antilocking system (EBC) level for every single riding
go back to the previous level and will automatically
mode.
highlight the message "MEMORY".
Enter the SETTING MENU.
Select the R. M. option by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU Note
button (4). To save the new EBC parameter setting follow
Enter the R.M. (Riding mode) Menu. the procedure "Storing Riding Mode settings"
Select the desired riding mode (RACE, SPORT or described in paragraph "Storing Riding Mode
WET), by pressing button (1) or (2). settings". If the user quits the Riding Mode
After selecting the desired riding mode (arrow beside customisation menu without performing the storing
the flashing riding mode), press the MENU procedure, the just-selected settings will be lost.
CONFIRMATION button (4).
You open the selected riding mode customisation
Menu. Select the parameter to be customised (EBC),
by pressing button (1) or (2). Once desired parameter
is highlighted, press CONFIRM MENU button (4).
When entering the function, the currently set EBC
level or status starts flashing.
Use buttons (1) and (2) to select the new desired
intervention level (1, 2 or 3) or the symbol " − " (that
identifies the "OFF" status) and press button (4) to

102
 4

2 1

1
2
4

Fig. 54

103
Customising Riding Modes: DTC level become automatically steady and the message "EXIT"
will be highlighted.
setting
To exit the menu and go back to previous page, select
This function disables or sets DTC level for the
"EXIT" and press button (4). The instrument panel will
selected riding mode.
go back to the previous level and will automatically
Enter the SETTING MENU. Select the R.M. (Riding
highlight the message "MEMORY".
mode) option by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4). Note
Enter the R.M. (Riding mode) Menu. Select the To save the new DTC parameter setting follow
desired riding mode (RACE, SPORT or WET), by the procedure "Storing Riding Mode settings"
pressing button (1) or (2). described in paragraph "Storing Riding Mode
After selecting the desired riding mode (arrow beside settings". If the user quits the Riding Mode
the flashing riding mode), press the MENU customisation menu without performing the storing
CONFIRMATION button (4). procedure, the just-selected settings will be lost.
You open the selected riding mode customisation
Menu.
Select the parameter to be customised (DTC), by
pressing button (1) or (2).
Once desired parameter is highlighted, press
CONFIRM MENU button (4).
When entering the function, the currently set DQS
level or status starts flashing. Use buttons (1) and (2)
to select the new desired intervention level (from 1
to 8) or the symbol " − " (that identifies the "OFF"
status) and press button (4) to confirm. The value will

104
 4

2 1

1
2
4

Fig. 55

105
Customising Riding Modes: DQS enable/ become automatically steady and the message "EXIT"
will be highlighted.
disable
To exit the menu and go back to previous page, select
This function disables or enables the DQS for the
"EXIT" and press button (4). The instrument panel will
selected riding mode.
go back to the previous level and will automatically
Enter the SETTING MENU. Select the R.M. (Riding
highlight the message "MEMORY".
mode) option by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4). Note
Enter the R.M. (Riding mode) Menu. Select the To save the new DQS parameter setting follow
desired riding mode (RACE, SPORT or WET), by the procedure "Storing Riding Mode settings"
pressing button (1) or (2). described in paragraph "Storing Riding Mode
After selecting the desired riding mode (arrow beside settings". If the user quits the Riding Mode
the flashing riding mode), press the MENU customisation menu without performing the storing
CONFIRMATION button (4). procedure, the just-selected settings will be lost.
You open the selected riding mode customisation
Menu. Select the parameter to be customised (DQS),
by pressing button (1) or (2).
Once desired parameter is highlighted, press
CONFIRM MENU button (4).
When entering the function, the currently set DQS
status starts flashing.
The DQS can be ON or OFF.
Use buttons (1) and (2) to select the new desired
status and press button (4) to confirm. The value will

106
 4

2 1

1
2
4

Fig. 56

107
Riding mode customisation: ABS To exit the menu and go back to previous page, select
"EXIT" and press button (4). The instrument panel will
adjustment
go back to the previous level and will automatically
This function disables or sets ABS level for the
highlight the message "MEMORY".
selected riding mode. Enter the SETTING MENU.
Select the R.M. (Riding mode) option by pressing
button (1) or (2). Note
Once function is highlighted, press CONFIRM MENU To save the new ABS parameter setting follow
button (4). the procedure "Storing Riding Mode settings"
Enter the R.M. (Riding mode) Menu. Select the described in paragraph "Storing Riding Mode
desired riding mode (RACE, SPORT or WET), by settings". If the user quits the Riding Mode
pressing button (1) or (2). customisation menu without performing the storing
After selecting the desired riding mode (arrow beside procedure, the just-selected settings will be lost.
the flashing riding mode), press the MENU
CONFIRMATION button (4). You open the selected Note
riding mode customisation Menu. Select the When you enable or disable the ABS through
parameter to be customised (ABS), by pressing this function, i.e. toggling from disabled to enabled
button (1) or (2). Once desired parameter is system or vice-versa, the procedure for activating or
highlighted, press CONFIRM MENU button (4). deactivating the ABS is carried out: the change of
When entering the function, the currently set ABS status of the ABS control unit is not instantaneous, it
level or status starts flashing. Use buttons (1) and (2) requires at least 6 seconds.
to select the new desired intervention level or the
symbol " − " (that identifies the "OFF" status) and
press button (4) to confirm. The value will become
automatically steady and the message "EXIT" will be
highlighted.

108
 4

2 1

1
2
4

Fig. 57

109
Customising Riding Modes: Engine setting Note
This function customises engine power associated To save the new ENGINE parameter setting
with each riding mode. follow the procedure "Storing Riding Mode settings"
Enter the SETTING MENU. Select the R.M. (Riding described in paragraph "Storing Riding Mode
mode) option by pressing button (1) or (2). settings". If the user quits the Riding Mode
Once function is highlighted, press CONFIRM MENU customisation menu without performing the storing
button (4). Enter the R.M. (Riding mode) Menu. procedure, the just-selected settings will be lost.
Select the desired riding mode (RACE, SPORT or
WET), by pressing button (1) or (2). After selecting the
desired riding mode (arrow beside the flashing riding
mode), press the MENU CONFIRMATION button (4).
You open the selected riding mode customisation
Menu.
Select the parameter to be customised (ENGINE), by
pressing button (1) or (2). Once desired parameter is
highlighted, press CONFIRM MENU button (4).
When entering the function, the currently set engine
power (HIGH, MED or LOW) starts flashing. Use
buttons (1) and (2) to select the new desired engine
power and press button (4) to confirm. The value will
become automatically steady and the message "EXIT"
will be highlighted.
To exit the menu and go back to previous page, select
"EXIT" and press button (4). The instrument panel will
go back to the previous level and will automatically
highlight the message "MEMORY".

110
 4
1 2

2
1
4

1 2

1
2
4

Fig. 58

111
Customising Riding Modes: Restore
default settings
This function allows restoring the default values set
by Ducati for the parameters relating to each riding
mode. Enter the SETTING MENU.
Select the R.M. (Riding mode) option by pressing
button (1) or (2). Once function is highlighted, press 4
CONFIRM MENU button (4). Enter the R.M. (Riding
mode) Menu. Select the desired riding mode (RACE,
SPORT or WET), by pressing button (1) or (2). After
selecting the desired riding mode (arrow beside the
flashing riding mode), press the MENU
CONFIRMATION button (4).
You open the selected riding mode customisation
Menu. Select the parameter to be customised
(DEFAULT), by pressing button (1) or (2). Once
desired parameter is highlighted, keep CONFIRM
MENU button (4) pressed for 2 seconds.

2
Fig. 59
112
The parameter restoration takes 2 seconds and the
display shows the message "DEFAULT" and its box
steady ON. Then "EXIT" is automatically highlighted.
To quit the menu and go back to SETTING MENU
main page, select "EXIT" and press button (4).

113
Engine rpm digital indication (RPM)
This function displays the number of RPMs in digital
format (recommended for improved accuracy when
setting idle rpm).
Enter the SETTING MENU. Select "RPM" option, by
pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4).
The display shows the numerical value of the RPM
with a precision of 50 rpm and fills the rpm bargraph
accordingly.
If the instrument panel is not receiving RPM value, a
string of five steady dashes "- - - - -" and the engine
rpm flashing bargraph are displayed to indicate an
undefined reading.
To quit the menu and go back to SETTING MENU
main page, select "EXIT" and press button (4).

Fig. 60
114
Battery voltage
This function allows you to check the motorcycle
battery voltage. Enter the SETTING MENU. Select
"BAT" (Battery) option, by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4). You open the BAT. menu (Battery).
The information will be displayed as follows:
- if battery voltage is below 11.0 V, a flashing the
message "LOW" is displayed;
- if battery voltage is between 11.0 V and 11.7 V
the reading will be displayed flashing;
- if battery voltage is between 11.8 V and 14.9 V
the reading will be displayed steady;
- if battery voltage is between 15.0 V and 16.0 V
the reading will be displayed flashing;
- if battery voltage is above 15.0 V, a flashing
message "HIGH" is displayed.

Fig. 61
115
If the battery voltage error is present, the instrument
panel will show three flashing dashes " - - - " as voltage
value, the EOBD light turns on together with the
Warning symbol and the corresponding "Batt." error
is displayed in the Error Menu.
If the instrument panel is not receiving battery voltage
value, a string of three steady dashes "- - -" is
displayed.
To quit the menu and go back to SETTING MENU
main page, select "EXIT" and press button (4).

Fig. 62

116
DDA
This function allows you to enable and disable the
DDA, view the percentage of memory used and to
delete data stored in the DDA memory.
The page for the DDA is only available when the
device is fitted to the motorcycle.

117
DDA enable/disable
To enable / disable the DDA device enter the
SETTING MENU. Select "DDA" option, by pressing
button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4).
You open the "DDA" menu.
When entering this function the display shows the
currently set DDA status: status ON indicates that the
DDA is active, otherwise status will be OFF.
Press buttons (1) and (2) to select the new desired
status (flashing) and press button (4) to confirm.
The set status value will be updated and the message
will return steady.
To exit the menu and go back to previous page, select
"EXIT" and press button (4).

Note
The DDA is automatically disabled by the
instrument panel upon every Key-OFF.

118
 4

2 1
1

2 1

2
1

Fig. 63

119
Viewing/deleting the DDA memory If deletion is successful, the instrument panel will
read OK for 2 seconds and refresh the memory status
This function allows displaying the DDA memory displayed. If deletion is not successful, the
status and erasing the stored data. instrument panel will still show memory used status.
To gain access to this function enter the SETTING To exit the menu and go back to previous page, select
MENU, use buttons (1) and (2) to select the message "EXIT" and press button (4).
"DDA" and press button (4).
When entering this function the DDA memory status
is displayed in percentage followed by the steady ON Warning
message "MEMORY" and the memory status value If the DDA is set to "ON" the deletion is inhibited
(in percentage): and you can not even select the ERASE option.

- 0 means that the DDA memory is empty;

- XX means that the DDA memory is used for the
indicated XX value;
- 100 means that the DDA memory is full.

With DDA OFF, you can delete the memory. Select

the flashing "ERASE" option, by pressing button (1) or
(2).
Press CONFIRM MENU (4) for at least 2 seconds to
confirm.
After 2 seconds, the instrument panel will show
flashing dashes "- - - - - " for as long as the deletion is
completed (from 1 to 128 seconds depending on the
quantity of data to be deleted).

120
 4

Fig. 64

121
Pin Code
This function makes it possible to "temporarily" turn
on the motorcycle if the E-LOCK system is not
working.
The PIN CODE is initially not present in the
motorcycle, it must be activated by the user by
entering his/her -digit PIN in the instrument panel,
otherwise the motorcycle cannot be started
temporarily in the case of a malfunction. To activate
this function, refer to "Entering the PIN CODE"
procedure.
To change the PIN refer to "Changing the PIN CODE"
procedure.
In order to temporarily start the motorcycle in case of
malfunction of the E-LOCK system, please refer to
the "Vehicle Release" procedure.

Warning
The motorcycle owner must activate (store) the
PIN code; if there is already a stored PIN, contact an
Authorised Ducati Dealer to have the function "reset".
To perform this procedure, the Authorised Ducati
Dealer may ask you to demonstrate that you are the
owner of the motorcycle.

122
Entering the PIN CODE
To activate the PIN CODE function and enter your
own PIN CODE you must open the SETTING MENU.
Select "PIN" option, by pressing button (1) or (2). Once
function is highlighted, press CONFIRM MENU
button (4).
When entering the function, the display shows the
message "N:" (new) followed by four flashing dashes
"- - - -".
Entering the code:
1) Press button (4), only one digit indicating "0"
starts flashing;
2) Each time you press the button (2) the displayed
number increases by one (+ 1) up to "9" and then
starts back from "0";
3) Each time you press the button (1) the displayed
number decreases by one (- 1) up to "1" and then
starts back from "0";
4) To confirm the number, press the button (4);

Repeat the procedures until you confirm all the digits

of the PIN CODE.

123
 4

2 1

Fig. 65

124
When you press button (4) to confirm the fourth and
last digit, the instrument panel highlights the
message "MEMORY" and the relevant box.
To save the new setting, hold button (4) for 2 seconds
while the message "MEMORY" is highlighted.
If settings have been saved, the message
"MEMORY" and the relevant box will be shown
4
steady ON for 2 seconds, and then the message
"EXIT" will be highlighted.
Once the first PIN CODE is stored, this menu page is
1 2
no longer available and is replaced by the page for
changing the PIN CODE. The page for entering the
very first PIN CODE is active and available again only
in case the PIN CODE function is reset (but this is only
possible at a DUCATI Authorised Service Centre).

2
Fig. 66
125
Changing the PIN CODE
To change the existing PIN CODE and activate a new
one, you must open the SETTING MENU.
Select "PIN" option, by pressing button (1) or (2). Once
function is highlighted, press CONFIRM MENU
button (4). When entering the function, the display
shows the message " O:" (old) followed by four
flashing dashes "- - - -".
Entering the "old" code:
1) Press button (4), only one digit indicating "0"
starts flashing;
2) Each time you press the button (2) the displayed
number increases by one (+ 1) up to "9" and then
starts back from "0";
3) Each time you press the button (1) the displayed
number decreases by one (- 1) up to "1" and then
starts back from "0";
4) To confirm the number, press the button (4);

Repeat the procedures until you confirm all the digits

of the PIN CODE.

126
 4

2 1

4
1

Fig. 67

127
When you press button (4) to confirm the fourth and
last digit:
- if the PIN code is correct, the instrument panel
displays "OK" for 2 seconds and then displays the
message " N:" (new) followed by four flashing
dashes "- - - -" of the new PIN.
- if the PIN is not correct, the instrument panel
displays "KO" for 2 seconds and then highlights
4 4 4
the string of four dashes "- - - -" for the old PIN to
allow you to try again;
- if there is a problem during the PIN check, the
instrument panel displays ERR. for 2 seconds
and then highlights the message "EXIT";

Fig. 68
128
Entering the "new" code:
1) Press button (4), only one digit indicating "0"
starts flashing;
2) Each time you press the button (2) the displayed
number increases by one (+ 1) up to "9" and then
starts back from "0";
3) Each time you press the button (1) the displayed
number decreases by one (- 1) up to "1" and then
starts back from "0";
4) To confirm the number, press the button (4);

Repeat the procedures until you confirm all the digits

of the PIN CODE.

129
 4

2 1

4
1

Fig. 69

130
When you press button (4) to confirm the fourth and
last digit, the instrument panel highlights the
message "MEMORY" and the relevant box.
To save the new setting, hold button (4) for 2 seconds
while the message "MEMORY" is highlighted.
If settings have been saved, the message
"MEMORY" and the relevant box will be shown
4
steady ON for 2 seconds, and then the message
"EXIT" will be highlighted.
If settings have not been saved, the instrument panel
highlights again the string of four dashes "- - - -" of the 1 2
new PIN to allow the rider to try again and enter a
new code.

2
Fig. 70
131
Clock
This function allows user to set or adjust the time.
To set the clock enter the SETTING MENU, use
buttons (1) and (2) to select CLK and press button (4) 2
to confirm. When entering this function, the current
time is displayed (for ex: AM 10 : 30) and the message
1 2
"AM" or "PM" flashes.
Use buttons (1) and (2) to set in the flashing mode the
messages "AM" or "PM", the digits relating to the
hours, the digits relating to the minutes and the 1
message "EXIT".
1 2

1 2

2
Fig. 71
132
Setting the hours
Press buttons (1) and (2) to select the digits
corresponding to the hours (flashing) and press
button (4) to confirm. The hour value starts flashing
faster. Use buttons (1) and (2) to decrease by 1 ("0",
"11", ....."1", "0" for AM and "12", "11", ......"1", "12" for 4
PM) and increase by 1 the hour value ("11", "0",
"1" ....."11" for AM and "12", "1", ......"12" for PM). Once
you reach the value to be set, press button (4) to
confirm and the set "hour" will stop flashing.

2 1

2
Fig. 72
133
Setting the minutes
Press buttons (1) and (2) to select the digits
corresponding to the minutes (flashing) and press
button (4) to confirm. The "minute value" starts
flashing faster. Use buttons (1) and (2) to decrease by
1 ("59", "58", ....."00", "59") and increase by 1 the 4
minute value ("00", "01", ....."59", "00"). Once you reach
the value to be set, press button (4) to confirm and
the set "minute value" will stop flashing.

2 1

2
Fig. 73
134
Setting am/pm
Press buttons (1) and (2) to select "AM" or "PM"
(flashing) and press button (4) to confirm. The "day
time" value starts flashing faster. Use buttons (1) and
(2) to change from "AM" to "PM" and vice versa. Once
4
you reach the value to be set, press button (4) to
1
confirm and the set "day time" value will stop flashing.
2

Note
Every time the battery is disconnected, the
clock is reset and must be set again by the user.
2
4
1

2
Fig. 74
135
Setting backlighting
This function allows adjusting the backlighting
intensity.
To set the backlighting enter the SETTING MENU,
use buttons (1) and (2) to select "B.L." and press
button (4) to confirm.
When entering this function, the currently used mode
name flashes.
Use buttons (1) and (2) to select the desired
brightness level (HIGH, MED, LOW) and press button
(4) to confirm.
The instrument panel immediately activates the
selected backlighting, keeps the message of the
selected mode steady ON and automatically
highlights the message "EXIT".
Select HIGH to set the display backlighting maximum
brightness - recommended in conditions of strong
ambient light.
Select MED to set the display backlighting medium
brightness (70%) - recommended in conditions of
medium/low ambient light.
Select LOW to set the display backlighting minimum
brightness (50%) - recommended in conditions of low
ambient light and/or during the night.
To exit the menu and go back to previous page, select
"EXIT" and press button (4).

136
 4

1 2
2 1

2 1
1 2

1
4
4

Fig. 75

137
LAP
The LAP function can be enabled and disabled by the
user through the SETTING MENU, in the LAP page.
When activating this function, the instrument panel
displays the stopped timer ( 0’ 00’’ 00 ) in MENU 1 on
the main screen.

Note
When the LAP function is active, the FLASH
button takes on the dual function of high beam
"FLASH" and LAP timer start / stop (new lap start
indication).

138
Enabling / disabling Lap recording
To enable / disable the Lap recording function, gain
access to the SETTING MENU, use buttons (1) and
(2) to select the LAP option and press button (4).
When entering the function, the currently set LAP
function status will be displayed. Press buttons (1)
and (2) to select the new desired status (flashing) and
press button (4) to confirm. The set status value will
be updated and the message will return steady.
To exit the menu and go back to previous page, select
"EXIT" and press button (4).
When the LAP function is disabled its status is OFF,
otherwise it is ON; if you select DATA, the instrument
panel shows the memorised Laps (A) whereas if you
select ERASE you can erase all memorised Laps (B).

Note
Upon Key-OFF, the "LAP" function status is
saved to restore it upon next Key-ON.

139
 1
4

2 2 1

2
1 2
1

1
2
4
1
2

Fig. 76

140
The LAPs previously stored using the "LAP
Recording" function in the Menu can be viewed on
the display.
The information displayed is lap time, maximum rpm
and top speed. Saved LAPs can also be deleted.

141
Displaying the stored LAPs next lap (laps are displayed in increasing order, i.e.
LAP 01 ... LAP 02 ... LAP 03 ..... LAP 30); and then
To view the stored LAPs, you must enter the highlight EXIT; use button (1) to view the previous lap
SETTING MENU. (laps are displayed in decreasing order, i.e. LAP 30 ...
Select "LAP" option, by pressing button (1) or (2). LAP 29 ... LAP 28 ..... LAP 01); and then highlight
Once function is highlighted, press CONFIRM MENU EXIT.
button (4). To exit the menu and go back to previous page, select
Press buttons (1) and (2) to select "DATA" (flashing) "EXIT" and press button (4).
and press button (4) to confirm.
When you enter the function, the following is
displayed: Note
The MAX stored speed is reached during lap
- The message "LAP" followed by the number of (increased by 5%).
the LAP (e.g.: LAP 01);
- the LAP number preceded by letter "n" (ex.: n01);
- the recorded lap time;
Note
If the memory is empty, the display shows the
- the top speed recorded during the lap;
lap timer reading "-.--.--", MAX RPM = ------ and MAX
- the RPM value recorded during the lap.
speed = -----.
Press the buttons (1) and (2) to highlight stored LAPS
one by one; in particular: use button (2) to view the

142
 1

4 2 1

2 1

Fig. 77

143
Erasing stored LAPs
To erase the stored LAPs, you must enter the
SETTING MENU.
Select "LAP" option, by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
4
button (4).
Press buttons (1) and (2) to select "ERASE" (flashing)
and keep button (4) pressed for 2 seconds to confirm.
After 2 seconds, the instrument panel display shows:
- five flashing dashes "- - - - -" for 3 seconds;
- OK for 2 seconds to inform about the result of
the deletion process.

Deletion is one single command that erases all stored

laps.
When the erasing procedure is completed the
instrument panel shows "EXIT".

Fig. 78
144
It is possible to erase the memorised LAPs also in the
DATA sub-menu. When entering the DATA page, the 1
instrument panel shows the memorised lap
information (ref. to paragraph "Displaying the stored 4
LAPs").
Press button (4) to highlight the message "ERASE". 4 2
User must confirm deletion by pressing button (4) for
2 seconds.
After 2 seconds, the instrument panel display shows:
- five flashing dashes "- - - - -" for 3 seconds;
- "OK" for 2 seconds to inform about the result of
the deletion process.

Deletion is one single command that erases all stored

laps.
After deletion, the Laps "01" to "30" are displayed with
all parameters showing an indefinite value "–" (time =
-’ - -’’ - - , rpm = - - - - - , speed = - - - ).
To exit the menu and go back to previous page, select
"EXIT" and press button (4).

Fig. 79
145
Setting the unit of measurement
This function allows you to change the units of
measurement of the displayed values, regardless of
the "Country configuration".
To manually set the units of measurement, you must
enter the SETTING MENU.
Select "UNT" option, by pressing button (1) or (2).
Once function is highlighted, press CONFIRM MENU
button (4).
When entering this function, use buttons (1) and (2)
to select the parameter for which you want to set a
new unit of measurement or to restore the default
settings:
- SPEED;
- temperature (TEMP.);
- fuel consumption (CONS.);
- reset to automatic settings (DEFAULT).

To exit the menu and go back to previous page, select

"EXIT" and press button (4).

146
 1

2 1
2

2 1

1 2 1
1
2
4

2
Fig. 80

147
Setting the unit of measurement: Speed
This function allows to change the units of
measurement of speed (and hence even the ones of
distance travelled). To gain access to this function
enter the SETTING MENU, use buttons (1) and (2) to
select UNT and press button (4). Select SPEED
option, by pressing button (1) or (2).
Once SPEED function (A) is highlighted, press 4
CONFIRM MENU button (4). When you enter the
function, the current unit of measurement is
displayed flashing, followed by the list of the possible
units steady ON: km/h, mph. Press buttons (1) and (2)
to highlight the units of measurement one by one: in 2 1
particular, use button (1) to highlight the following
item and button (2) to highlight the previous item.
Select the required unit of measurement and then
press the CONFIRM MENU button (4) to confirm: the
selected unit is stored in the instrument panel, the
unit of measurement indication becomes steady and 4
the "EXIT" option is highlighted.
1

Fig. 81
148
The selected unit of measurement will be used by the
instrument panel for the following indications:
- motorcycle speed and Average speed (km/h or
mph);
- Odometer, Trip A, Trip B and Trip Fuel (km or
miles).

149
Setting the unit of measurement: Temperature
This function allows you to change the units of
measurement of the temperature.
To gain access to this function enter the SETTING
MENU, use buttons (1) and (2) to select UNT and
press button (4).
Select TEMP option, by pressing button (1) or (2).
Once TEMP. function (B) is highlighted, press 4
CONFIRM MENU button (4).
When you enter the function, the current unit of
measurement is displayed flashing, followed by the
list of the possible units steady ON: °C, °F.
Press buttons (1) and (2) to highlight the units of 2 1
measurement one by one: in particular, use button (1)
to highlight the following item and button (2) to
highlight the previous item. Select the required unit
of measurement and then press the CONFIRM
MENU button (4) to confirm: the selected unit is 4
stored in the instrument panel, the unit of
measurement indication becomes steady and the 1
"EXIT" option is highlighted.
The selected unit of measurement will be used by the
4
instrument panel for the following indications:
- Engine coolant temperature and ambient air 2
temperature.
Fig. 82
150
Setting the unit of measurement: Fuel
consumption
This function allows you to change the units of
measurement of the fuel consumption.
To gain access to this function enter the SETTING
MENU, use buttons (1) and (2) to select UNT and
press button (4).
Select CONS. option, by pressing button (1) or (2). 4
Once CONS. function (C) is highlighted, press
CONFIRM MENU button (4). When you enter the
function, the current unit of measurement is
displayed, followed by the list of the possible units:
L / 100km, km / L, mpg (UK), mpg (USA). 2 1
Press buttons (1) and (2) to highlight the units of
measurement one by one: use button (1) to highlight
the following item and button (2) to highlight the
previous item.
Select the required unit of measurement and then 4
press the CONFIRM MENU button (4) to confirm: the
selected unit is stored in the instrument panel, the 1
unit of measurement indication becomes steady and
the "EXIT" option is highlighted. 4

Fig. 83
151
The selected unit of measurement will be used by the
instrument panel for the following indications:

- Instantaneous fuel consumption and Average

fuel consumption.

152
Setting the unit of measurement: Restore
automatic settings
This function allows you to restore the automatic
settings for the units of measurement of all
indications displayed on the instrument panel.
To gain access to this function enter the SETTING
MENU, use buttons (1) and (2) to select UNT and
press button (4). Select DEFAULT option, by pressing 4
button (1) or (2).
Once DEFAULT function (D) is highlighted, press
CONFIRM MENU button (4) for 2 seconds. After 2
seconds the display shows the message "DEFAULT"
and its box steady ON for 2 seconds. Then EXIT is
automatically highlighted.
To exit the menu and go back to previous page, select
EXIT and press button (4).
4

Fig. 84
153
Chart of the units of measurement
TOT SPEED T_ENGINE INSTANTANEOUS
TRIPA AVERAGE SPEED T_AIR FUEL CONSUMP-
TRIPB TION
TRIP FUEL AVERAGE FUEL
CONSUMPTION
Europe km km/h °C l/100km
UK miles mph °C mpg UK
USA miles mph °F mpg USA
Canada km km/h °C l/100km
France km km/h °C l/100km
Japan km km/h °C l/100km
Brazil km km/h °C l/100km
Taiwan km km/h °C l/100km
China km km/h °C l/100km

154
Light control
1
Low / High beam
This function allows you to reduce current
consumption from the battery, by managing
headlight switching-on and off.
At Key-ON, the high beam and low beam lights are
OFF, only the parking lights are turned on. B
Once the engine is started, the low beam is turned
on; with engine running the standard operation of the A
lights is restored: it is possible to switch on and OFF
the high beam using button (1) in position (A), or
FLASH using button (1) in position (B). If the engine
1
is not started after Key-ON, it is still possible to turn
on the low/high beam by pressing button (1) in
position (A) on the left switch; press it once to turn
on the low beam; any further time you press it you
switch between low and high beam. 3

5
Fig. 85
155
If engine is not started within 60 seconds since the
button was first pressed, the low and high beam
lights are turned OFF.
If the low beam or high beam was turned on before
starting the engine (with the procedure described
above), the headlight turns off automatically when
starting the engine and will turn ON again when the
engine has been completely started.
Turn indicators
Turn indicators are automatically reset by the
instrument panel.
After activating one of the two turn indicators, user
can reset them using the button (3, Fig. 85) on the left
switch.
If the turn indicator is not reset manually, the
instrument panel will automatically switch it off after
the motorcycle has travelled 500 m (0.3 miles) from
when the turn indicator was activated. The counter
for the distance travelled for automatic deactivation
is only activated at speeds below 80 km/h (50 mph).
If the calculation of the distance for automatic
deactivation is activated and then the motorcycle
exceeds a speed of 80 km/h (50 mph), the calculation
is interrupted and will restart when the speed returns
below the indicated threshold.

156
Parking function

Note
If there is a sudden interruption in the battery
while the function is active, the instrument panel will
disable the function when the voltage is restored.

The "Parking" function activates the front and rear

parking lights when the motorcycle is turned off, so
it is visible when parked. The function is activated by
pressing the button (5,Fig. 85) for 3 seconds during
the first 60 seconds after the motorcycle was turned Fig. 86
off (after Key-OFF).
Once the function is activated, the message "PARK" To interrupt the function, turn the motorcycle ON and
is displayed for 3 seconds and the lights stay ON as OFF (Key-ON / Key-OFF).
long as the battery voltage is ≤ (higher than or equal to)
12.2 V. If voltage is < (below) 12.2 V the lights turn Important
off automatically in order to save battery charge. The frequent use of this function can
considerably reduce the battery charge; it is
recommended to use this function only when really
necessary.

157
Hazard function 7
The HAZARD function turns all four turn indicators on
at the same time to signal an emergency condition.
The HAZARD function is activated by taking button
(4) to position (6) for 3 seconds. Activation is only
possible when motorcycle is ON (i.e. when key is
turned to ON while engine status does not matter).
When the HAZARD function is active, all four turn
indicators blink at the same time as well as warning
lights (7) on the instrument panel. The "Hazard"
function can be disabled both with motorcycle on (key
set to "ON") - by taking button (4) to position (6) or by
taking button (4) to its central position - and with
motorcycle off (key set to OFF) by taking button (4)
to position (6).

4
Fig. 87
158
After activating the "Hazard" function, if motorcycle is Note
switched OFF (key set to OFF), the function stays The "Hazard" function has higher priority
active until manually disabled by user or as long as compared to normal operation of the single turn
battery voltage is ≤ (higher than or equal to) 12.2 V. indicators, this means that, as long as it is active, it
When voltage drops < (below) 12.2 V the turn will not be possible to activate the single right or left
indicators switch OFF automatically in order to save turn indicators.
battery charge.

Note
If user performs a Key-ON while the "Hazard"
function is still active, the function will remain ON
(temporary turn indicator control interruption is
allowed during the instrument panel initial check
routine).

Note
If there is a sudden interruption in the battery
while the function is active, the instrument panel will
disable the function when the voltage is restored.

159
The Immobilizer system
For improved antitheft protection, the motorcycle is
equipped with an IMMOBILIZER, an electronic
system that inhibits engine operation whenever the
ignition switch is turned off.
Accommodated in the handgrip of each ignition key
is an electronic device that modulates an output
signal. When the ignition is turned on this signal is
generated by a special antenna incorporated in the
switch and changes every time.
The modulated signal represents the “password”
(which is changed at each start-up) by which the ECU
recognizes the ignition key. The ECU will only allow
the engine to start if it recognises this password.

160
Keys
The owner receives 2 keys with the vehicle.
These keys contain the "immobilizer system code". B
The keys (B) are regular ignition keys and are used to:
- start up the engine;
- open the fuel tank filler plug;
- open the seat lock.

Warning
Keep the 2 keys separate and use only one of
them to start the motorcycle.
Fig. 88

161
Operation
When the ignition key is turned to OFF, the
immobilizer inhibits engine operation.
If the other key does not work out either, contact the
Ducati Service network.

Warning
Any important shock might damage the
electronic components fitted into the key. Use only
one key during the procedure. Using different keys
could prevent the system from recognising the code
in the key.

162
Duplicate keys
If you need any duplicate keys, contact the Ducati
Service network with all the keys you have left.
The Ducati Service Centre will program all the new
keys as well as any keys you already have.
You may be asked to provide proof that you are the
legitimate owner of the motorcycle.
The codes of any keys not submitted will be wiped
off from the memory to make those keys
unserviceable in case they have been lost.

Note
If you sell your motorcycle, do not forget to give
all keys to the new owner.

163
Vehicle release through PIN CODE
In case of key acknowledgement system or key
malfunction, the instrument panel allows the user to
enter his/her own PIN code to temporarily restore
motorcycle operation. If the PIN CODE function is not
active, the instrument panel does not activate the
page for entering the code, but shows the Standard
screen instead, triggers the E-LOCK error to inform
the user that there is a problem with key reading/
acknowledgement and disables the opportunity to
enter the SETTING MENU except for the Error page
(ERR.). The E-LOCK error warning remains active until
next Key-OFF.
If the PIN CODE function is active, the instrument
panel activates the page for entering the code and
displays the message "PIN" with a string of four
flashing dashes " - - - - ".

164
Entering the code (A):
1) Press button (4), only one digit indicating "0"
starts flashing;
2) Each time you press the button (2) the displayed
number increases by one (+ 1) up to "9" and then
starts back from "0";
3) Each time you press the button (1) the displayed
number decreases by one (- 1) up to "1" and then 4
starts back from "0";
4) To confirm the number, press the button (4); 4
Repeat the procedures until you confirm all the digits
of the PIN CODE.

1
4
4

Fig. 89
165
When you press button (4) to confirm the fourth and
last digit
- If the PIN code is correct, the instrument panel
displays "OK" for 2 seconds and then shows the
"Standard screen" and triggers the E-LOCK error
to still show the user that there is a problem with
key reading/acknowledgement.
- if the PIN is not correct, the instrument panel
4 4 4
displays "KO" for 2 seconds and then highlights
the string of four dashes "- - - -" to allow you to try
again. The number of possible attempts is
determined by a preset time-out of 2 minutes.
After this time, the instrument panel shows the
Standard screen, triggers the E-LOCK error and
disables the opportunity to enter the SETTING
MENU except for the Error page (ERR.).
- if there is a problem during the PIN CODE check,
the instrument panel displays ERR. for 2 seconds
and then responds in the same way as for the
"KO" error described in the previous point.
1

Fig. 90
166
 Important
If this procedure is necessary in order to start
the motorcycle, contact an Authorised Ducati Service
Centre as soon as possible to fix the problem.

167
Controls
1

Position of motorcycle controls 4 7

Warning 6
This section shows the position and function of 3
the controls used to ride the motorcycle. Be sure to
read this information carefully before you use the 2
controls. 5

1) Instrument panel. 8
2) Key-operated ignition switch and steering lock. 9
3) Left switch.
4) Clutch lever.
5) Right switch.
6) Throttle twistgrip.
7) Front brake lever.
8) Rear brake pedal.
9) Gear change pedal.

Fig. 91
168
Ignition switch and steering lock
It is located in front of the fuel tank and has three A
positions: B
A) ON: enables lights and engine operation;
B) OFF: disables lights and engine operation;
C) LOCK: the steering is locked;
C
Note
To move the key to the last position, press it
down before turning it. The key can be removed in
positions (B) and (C).
Fig. 92

169
Left-hand switch 1
1) Dip switch, two-position light selector switch:
(A) every time it is pressed down the light switches
from low beam ON ( ) to low beam and high beam
ON;
(B) pushed to the side ( ) high beam flasher
(FLASH), START/STOP LAP function.
B
2) 3-position turn indicator switch ( ):
centre position = OFF;
A
position ( ) = left turn;
3) Turn indicator OFF, RIDING MODE activation and
menu navigation button. 5
4) Button ( ) = warning horn. 1
5) Navigation menu, display scroll and TRIP A and
TRIP B reset button.
6) Navigation menu, display scroll button.
2

4 6
Fig. 93
170
Clutch lever
Lever (1) disengages the clutch. It features a dial
adjuster (2) for lever distance from the twistgrip on
handlebar. The lever distance can be adjusted
through 10 clicks of the dial (2). Turn clockwise to
increase lever distance from the twistgrip. Turn the
adjuster counter clockwise to decrease lever
distance. When the clutch lever (1) is operated, drive
from the engine to the gearbox and the drive wheel
is disengaged. Using the clutch properly is essential
to smooth riding, especially when moving OFF. 2 1

Warning Fig. 94
Set clutch lever when motorcycle is stopped.
Note
The engine can be started with the side stand
Important
down and the gearbox in neutral. If starting with a
Using the clutch properly will avoid damage to
gear engaged, pull in the clutch lever (in this case the
transmission parts and spare the engine.
side stand must be up).

171
Right-hand switch
1) Red ON/OFF switch. 1
2) Black ENGINE START button.
The switch (1) has three positions:
2
A) centre: RUN OFF.
In this position, the engine cannot be started and all
electronic devices are OFF.
B) pushed down: ON/OFF.
In this position, the system can be turnedON(Key-
ON) and OFF (Key-OFF).
C) pushed up: RUN ON.
The engine can only be started in this position, Fig. 95
pushing the black button (2).
1

A
B
2

Fig. 96
172
Throttle twistgrip
The twistgrip (1) on the right handlebar opens the
throttles.
When released, it will spring back to the initial
position (idling speed).

Fig. 97

173
Front brake lever
Pull in the lever (1) towards the twistgrip to operate
the front brake. The system is hydraulically operated
and you just need to pull the lever gently.
The brake lever (1) has a dial (2) for adjusting the
distance between lever and twistgrip on the
handlebar.
The lever distance can be adjusted through 10 clicks
of the dial (2). Turn clockwise to increase lever
distance from the twistgrip. Turn the adjuster counter
clockwise to decrease lever distance.
1 2
Fig. 98

174
Rear brake pedal
Push down on the pedal (1) to apply the rear brake.
The system is hydraulically operated.

Fig. 99

175
Gear change pedal
When released, the gear change pedal (A)
automatically returns to rest position (N) in the centre.
This is indicated by the instrument panel NEUTRAL
light (N) coming on.
The pedal can be moved: A
- down = press down the pedal to engage the 1st
gear and to shift down. The NEUTRAL (N) light 6
will go out; 5
4 1
- upwards= lift the pedal to engage 2nd gear and 3 2 N
then 3rd, 4th, 5th and 6th gears.
Fig. 100
Each time you move the pedal you will engage the
next gear.

176
Adjusting the position of the gearchange
and rear brake pedals
The position of the gearchange and rear brake pedals
in relation to the footrests can be adjusted to suit the
requirements of the rider.
Adjust the pedals as follows:
Gear change pedal
Hold linkage (1) using the special flat (A) and loosen
nut (2).
A 1 2
Fit an open-end wrench to hexagonal element of
linkage (1) and rotate until setting pedal in the desired Fig. 101
position.
Tighten nut (2) onto linkage.

177
Rear brake pedal
Loosen counter nut (7).
Turn pedal stroke adjusting screw (6) until pedal is in
the desired position. Tighten the counter nut (7).
Operate the pedal (8) by hand to check that there is
1.5 to 2 mm of free play before the brake bites.
If not, adjust the length of the master cylinder
pushrod.

Warning
Have the pedal adjusted at a Ducati Dealer or 6 7
authorised Service Centre. Fig. 102

6 8

Fig. 103
178
Main components and
devices 6 6

Position on the vehicle

1) Tank filler plug.
2) Seat lock.
3) Side stand.
4) Rear-view mirrors.
7
5) Front fork adjusters. 5 3 8
6) Rear shock absorber adjusters.
7) Catalytic converter (both sides).
8) Exhaust silencer (both sides). 4 5 2

4 5 1
Fig. 104
179
Tank filler plug
Opening 1
Lift the protection lid (1) and fit the ignition key into
the lock. Turn the key clockwise 1/4 turn to unlock.
Lift the plug (2).
Closing
Refit the plug (2) with the key in it and push it down
into its seat. Remove the key and replace the lock
cover (1).

Note Fig. 105

The plug can only be closed with the key in.

Warning
Always make sure you have properly refitted
and closed the plug after refuelling.

Fig. 106
180
Seat lock
Opening
Insert the key into the seat lock (1) and turn it until the
seat cover (2) catch disengages with an audible click.
Pull the seat cover (2) towards the front end of the
motorcycle until releasing it.
Closing
Insert the seat cover (2) from the side and push it
towards the rear end of the motorcycle until fully
1
home.
Fig. 107
Warning
To close the seat cover insert it from the
2
motorcycle side and slide it towards the rear side until
hearing the engagement click.

Fig. 108
181
Side stand 2

Important
Place the motorcycle on the side stand only
when you are not going to use it for short periods of
time. Before lowering the side stand, make sure that
the bearing surface is hard and flat.
1
Do not park on soft or pebbled ground or on asphalt
melt by the sun heat and similar or the motorcycle
may fall over. When parking in downhill road tracts,
always park the motorcycle with its rear wheel facing
downhill. Fig. 109
To pull down the side stand, hold the motorcycle
handlebars with both hands and push down on the Warning
side stand (1) with your foot until it is fully extended. Do not sit on the motorcycle when it is
Tilt the motorcycle until the side stand is resting on supported on the side stand.
the ground.
To move the side stand to its rest position (horizontal Note
position), lean the motorcycle to the right while lifting Check for proper operation of the stand
the thrust arm (1) with your foot. mechanism (two springs, one into the other) and the
safety sensor (2) at regular intervals.

182
 Note
The engine can be started with the side stand
down and the gearbox in neutral. If starting with a
gear engaged, pull in the clutch lever (in this case the
side stand must be up).

183
Steering damper
It is located before the handlebar and is secured to
the steering head.
It provides stable and accurate steering, improving
the motorcycle's handling response under any
conditions.

Fig. 110

184
Adjusting the front fork 2
The front fork used on this motorcycle has rebound,
compression and spring preload adjustment.
Adjustment is done by external screw adjusters.
1) For rebound adjustment (1, Fig. 111);
2) For compression adjustment (2, Fig. 111);
3) For spring preload adjustment (3, Fig. 112); 1

Put the motorcycle on the side stand and make sure

it is stable.
Turn adjuster (1) at the top end of each fork leg with
a flat-blade screwdriver to adjust rebound.
Fig. 111
Turn adjuster (2) at the top end of each fork leg with
a flat-blade screwdriver to adjust compression.

Fig. 112
185
Turn adjusters (1) and (2) to adjust damping. The
stiffest damping setting is obtained with the adjuster
turned fully clockwise to the "0" position. Starting
from this position, turning counter clockwise, you can
count the turns.
To change preload of the spring inside each fork leg,
turn the hex. adjuster (3, Fig. 112) with a hexagon
wrench, starting from the fully open (clockwise)
position.
STANDARD settings are as follows:
compression: 4 turns (from fully closed position);
rebound: 5 turns (from fully closed position);
spring preload: 4 turns (from fully open position).

Warning
Set both leg adjusters on the same positions.

186
Adjusting the rear shock absorber
The rear shock absorber has commands that enable 2
you to adjust the setting to suit the load on the
motorcycle.
The adjuster (1) located on the front connection
holding the shock absorber to the crankcase half
adjusts the damping during the rebound phase
(return).
The adjuster (2) located on the expansion reservoir of
the shock absorber adjusts the damping during the
compression phase.
The two nuts (3) on the upper part of the shock
absorber serve to adjust the preload of the external Fig. 113
spring.
To change spring preload, slacken the upper locking 3
ring nut. Then TIGHTEN or SLACKEN the lower ring
nut to INCREASE or DECREASE spring preload.
After setting spring preload as desired, tighten the
upper locking ring nut.

Fig. 114
187
STANDARD setting: from the fully closed position
(clockwise), loosen as follows:
compression: 2.5 turns from fully closed position;
rebound: 12 clicks from fully closed position;
spring preload: 17 mm.

Warning
The shock absorber is filled with gas under
pressure and may cause severe damage if taken apart
by unskilled persons.

When carrying a passenger and luggage, set the rear

shock absorber spring to proper preload to improve
motorcycle handling and keep safe clearance from
the ground. You may find that rebound damping
needs adjusting as well.
The table in the next page shows the recommended
settings according to the use, experience and needs
of the rider.

188
CHOOSING SUSPENSION CALIBRATION
Ducati recommends the front fork and rear suspension calibration values indicated in the table: these values
are merely suggestions based on different riding conditions as well as on the user's ability and comfort
requirements.

Important
The settings indicated in the table do not depend on the riding modes set by the rider on the instrument
panel.

Track - Performance use

Parameter Front fork Rear shock absorber
Spring preload 6 turns from fully open 19 mm (÷ 2 mm)
Compression 1 turn from fully closed 0.5 turns from fully closed
Rebound 2.5 turns from fully closed 8 clicks from fully closed

ROAD - Comfort use

Parameter Front fork Rear shock absorber
Spring preload 2 turns from fully open 17 mm
Compression 7 turns from fully closed 3.5 turns from fully closed
Rebound 5 turns from fully closed 15 clicks from fully closed

189
The vehicle is sold with a calibration (standard settings indicated in the previous paragraphs) that is suitable
for a range of different uses (riding conditions, ability and requirements of the user), in order to achieve the
best solution in terms of on-road sports riding.

190
Riding the motorcycle 1 2

Running-in recommendations
Maximum rotation speed
Rotation speed for running-in period and during
standard use (rpm):
1) up to 1,000 km;
2) from 1,000 to 2,500 km.
Up to 1,000 km Fig. 115
During the first 1,000 km of riding, pay attention to To this end, roads with plenty of bends and even
the revolution counter since the following speed slightly hilly areas are ideal for a most efficient
must not be absolutely exceeded: 5,500÷ 6,000 rpm running-in of engine, brakes and suspensions.
(included). For the first 100 km use the brakes gently. Avoid
During the first hours of riding, it is advisable to run sudden or prolonged braking. This will allow the
the engine at varying load and rpm, though still within friction material on the brake pads to bed in against
recommended limit. the brake discs.
For all mechanical parts of the motorcycle to adapt to
Strict observance of running-in recommendations will one another and above all not to adversely affect the
ensure longer engine life and reduce the likelihood of life of basic engine parts, it is advisable to avoid harsh
overhauls and tune-ups. accelerations and not to run the engine at high rpm
for too long, especially uphill.

191
Furthermore, the drive chain should be inspected
frequently. Lubricate as required.
From 1,000 to 2,500 km
At this point, you can squeeze some more power out
of your engine. However never exceed 7,000 rpm.

Important
During the whole running-in period, the
maintenance and service rules recommended in the
Warranty Booklet should be observed carefully.
Failure to comply with these rules will release Ducati
Motor Holding S.p.A. from any liability whatsoever for
resulting engine damage or shorter engine life.

Strict observance of running-in recommendations will

ensure longer engine life and reduce the likelihood of
overhauls and tune-ups.

192
Pre-ride checks - CONTROLS
Work the brake, clutch, throttle and gear change
controls (levers, pedals and twistgrip) and check
Warning
for proper operation.
Failure to carry out these checks before riding,
- LIGHTS AND INDICATORS
may lead to motorcycle damage and injury to rider
Make sure lights, indicators and horn work
and passenger.
properly. Replace any burnt-out bulbs (page
219).
Before riding, perform a thorough check-up on your
- KEY LOCKS
motorcycle as follows:
Ensure that tank filler plug (page 180) and seat
- FUEL LEVEL IN THE TANK (page 181) are properly locked.
Check the fuel level in the tank. Fill tank if needed - SIDE STAND
(page 201). Make sure side stand operates smoothly and is
- ENGINE OIL LEVEL in the correct position (page 182).
Check oil level in the sump through the sight
glass. Fill tank if needed (page 227).
- BRAKE AND CLUTCH FLUID
Check fluid level in the relevant reservoirs (page
208).
- COOLANT
Check coolant level in the expansion reservoir.
Top up if needed (page 206).
- TYRE CONDITION
Check tyre pressure and condition (page 224).

193
ABS light
After Key-ON, the ABS light (9) stays ON.
When the motorcycle speed exceeds 5 km/h, the
warning light switches OFF to indicate the correct
operation of the ABS system.

Warning
In case of malfunction, do not ride the
motorcycle and contact a Ducati Dealer or authorised
Service Centre.

194
ABS device
Check that the front (1) and rear (2) phonic wheels are
clean.

Warning
Clogged reading slots would compromise
system proper operation. It is recommended to
disable ABS system in case of muddy road surface
because under this condition the system might be
subject to sudden failure.
1

Warning Fig. 116

Prolonged rearing could deactivate the ABS
system. 2

Fig. 117
195
Starting the engine
B A
Warning
Before starting the engine, become familiar
with the controls you will need to use when riding.
C
Warning
Never start or run the engine indoors. Exhaust
gases are poisonous and may lead to loss of
consciousness or even death within a short time.

Move the ignition key to ON. Make sure both the Fig. 118
green light N (1) and the red light (2) on the
instrument panel come on. 1 2

Important
The oil pressure light should go out a few
seconds after the engine has started.

Fig. 119

196
 Warning
The side stand must be fully up (in a horizontal 3
position) as its safety sensor prevents engine start
when down.
4
Note
It is possible to start the engine with side stand
down and the gearbox in neutral. When starting the
motorcycle with a gear engaged, pull the clutch lever
(in this case the side stand must be up).

Important Fig. 120

Do not rev up the engine when it is cold. Allow
some time for oil to be heated and reach all points
that need lubricating.

Check that the stop switch (3) is positioned to RUN,

then press the starter button (4).

197
Moving off Warning
1) Disengage the clutch by squeezing the clutch Avoid harsh accelerations, as this may lead to
lever. misfiring and transmission snatching. The clutch
2) Push down the gear change lever firmly with the lever should not be held in longer than necessary
tip of your foot to engage first gear. after a gear is engaged, otherwise friction parts may
3) Raise the engine revs by turning the throttle overheat and wear out.
twistgrip while gradually releasing the clutch
lever. The motorcycle will start moving off. Warning
4) Release the clutch lever completely and Prolonged rearing could deactivate the ABS
accelerate. system.
5) To shift up, close the throttle to slow down
engine, disengage the clutch, lift the gear change
Braking
lever and release the clutch lever. To shift down,
Slow down in time, shift down to engine-brake first
proceed as follows: release the twistgrip, pull the
and then brake applying both brakes. Pull the clutch
clutch lever, shortly speed up to help gears
lever before stopping the motorcycle, to avoid
synchronise, shift down (engage next lower
sudden engine stop.
gear) and release the clutch.
ABS system
The controls should be used correctly and timely: Using the brakes correctly under adverse conditions
when riding uphill do not hesitate to shift down as is the hardest – and yet the most critical - skill to
soon as the motorcycle tends to slow down, so you master for a rider. Braking is one of the most difficult
will avoid stressing the engine and the motorcycle and dangerous moments when riding a two wheeled
abnormally. motorcycle: the possibility of falling or having an
accident during this difficult moment is statistically
higher than any other moment. A locked front wheel

198
leads to loss of traction and stability, resulting in loss Warning
of control. With the ABS system deactivated, the vehicle
The Anti-Lock Brake System (ABS) has been maintains the characteristics of the standard braking
developed to enable riders to use the motorcycle system, therefore the use of only one of the brakes
braking force to the fullest possible amount in reduces the motorcycle's braking efficiency. Never
emergency braking or under poor pavement or use the brake controls harshly or suddenly; as you
adverse weather conditions. may lock the wheels and lose control of the
ABS uses hydraulics and electronics to limit pressure motorcycle. When riding in the rain or on slippery
in the brake circuit when a special sensor mounted to surfaces, braking capacity is significantly reduced.
the wheel signals the electronic control unit that the Always use the brakes very gently and carefully when
wheel is about to lock up. riding under these conditions. Any sudden
This avoids wheel lockup and preserves traction. manoeuvres may lead to loss of control. When
Pressure is raised back up immediately and the tackling long, high-gradient downhill road tracts, shift
control unit keeps controlling the brake until the risk down gears to use engine braking. Apply one brake
of a lockup disappears. Normally, the rider will at a time and use brakes sparingly. Keeping the
perceive ABS operation as a harder feel or a pulsation brakes applied all the time would cause the friction
of the brake lever and pedal. material to overheat and reduce braking power
The front and rear brakes use separate control dangerously. Tyre inflation pressures below the
systems, meaning that they operate independently. specified value will reduce braking efficiency, and
Likewise, the ABS is not an integral braking system compromise steering precision and road holding on
and does not control both the front and rear brake at bends.
the same time.
If desired, the system can be deactivated from the
instrument panel, using the "Customising Riding
Modes: ABS setting page 108" function.

199
Stopping the motorcycle Warning
Reduce speed, shift down and release the throttle The exhaust system might be hot, even after
twistgrip. Shift down to engage first gear and then engine is switched OFF; pay particular attention not
neutral. to touch exhaust system with any body part and do
Apply the brakes and bring the motorcycle to a not park the motorcycle next to inflammable material
complete stop. (wood, leaves etc.).
To switch the engine off, simply turn the key to OFF.
Parking Warning
Stop the motorcycle, then put it on the side stand. To Using padlocks or other locks designed to
prevent theft, turn the handlebar fully left and turn the prevent motorcycle motion, such as brake disc locks,
ignition key to the LOCK position. rear sprocket locks, and so on is dangerous and may
If you park in a garage or other indoor area, make sure impair motorcycle operation and affect the safety of
that there is proper ventilation and that the rider and passenger.
motorcycle is not near a source of heat.

Important
Never leave the ignition key in the switch when
you are leaving your motorcycle unattended.

200
Refuelling
Never overfill the tank when refuelling. Fuel should
never be touching the rim of filler recess.

Warning
Use fuel with low lead content and an original
octane number of at least 95.

Warning
The vehicle is only compatible with fuel having
a maximum content of ethanol of 10% (E10).
Using fuel with ethanol content over 10% is
forbidden. Using it could result in severe damage of
the engine and motorcycle components. Using fuel Max level
with ethanol content over 10% will make the
warranty null and void.

Fig. 121
201
Tool kit and accessories
The tool kit (1) is located under the seat and includes: 1
- Box wrench for spark plugs;
- Tommy bar for plug wrench;
- Double-tip screwdriver;
- Allen wrench for fairings.

To access the compartment remove the passenger

seat (page 181).
Have the following parts (supplied as standard)
installed by a Ducati Dealer or authorised Service
Centre: Fig. 122
- passenger seat;
- right and left rear footpegs;

202
Main maintenance operations

Remove the fairing

Some parts of the motorcycle fairing have to be
removed for certain maintenance or repair
operations.

Warning
Failed or incorrect refitting of one of the
removed components could cause its sudden
detachment while riding resulting in loss of control of
the motorcycle.

Important
At every reassembly, to avoid damaging the
painted areas and the Plexiglas windscreen, always
place the nylon washers at the retaining screws.

Important
Have the fairings removed at a Ducati Dealer or
Authorised Service Centre.

203
Side fairings 2 3 5
To remove the fairings, use the Allen wrench
accommodated under the seat to loosen the
following:
- the two screws (1) securing the fairing panels to
the brackets;
- the four screws (2) securing the fairing panels to
the headlight fairing;
- the three screws (3) securing the fairing panels
to the frame;
- the two screws (4) located under the fairing that 4 4 1
join the right fairing panel to the left fairing panel;
Fig. 123
- the two screws (5) securing the fairing panels at
the centre;
- the two screws (6) securing the front of the
fairing to the headlight fairing.
6
Note
Be careful of the splashguard, which is released
by the fairing panel fastening.

Note
To refit the left fairing panel, lower the side
stand and pass it through the hole in the panel.
Fig. 124
204
Change the air filter

Important
Have the air filter maintenance performed at a
Ducati Dealer or authorised Service Centre.

205
Check and top up the coolant level
Check coolant level in the expansion tank on the right
side of the motorcycle.
Check that the level is between the MIN (1) and MAX
(2) marks on the side of the expansion reservoir.
Top up if the level is below the MIN mark.
Remove the right-hand side fairing (page 204). 2

Fig. 125

206
Unscrew the filler plug (3) and add ENI Agip
Permanent Spezial antifreeze (do not dilute, use 3
pure), until reaching the MAX level.
Refit the filler plug (3) and reassemble all removed
parts. This type of mixture ensures the best operating
conditions (the coolant starts to freeze at -20 °C/-4 °F).
Cooling circuit capacity: 2.3 cu. dm (litres).

Warning
Place the motorcycle upright on a flat surface
and make sure the engine is cold before proceeding.

Fig. 126
Important
Have the top-up performed at a Ducati Dealer or
Authorised Service Centre.

207
Check brake and clutch fluid level
The levels should not fall below the MIN marks on the
respective reservoirs.
If level drops below the limit, air might get into the
circuit and affect the operation of the system MAX
involved.
Brake and clutch fluid must be topped up and MIN MAX
changed at the intervals specified in the scheduled
maintenance table reported in the Warranty Booklet;
please contact a Ducati Dealer or authorised Service MIN
Centre.

Important Fig. 127

It is recommended all brake and clutch lines be
changed every four years.

MAX

MIN

Fig. 128
208
Brake system Warning
If you find exceeding clearance on brake lever or Clutch fluid level will increase as clutch plate
pedal and brake pads are still in good condition, friction material wears down. Do not exceed the
contact your Ducati Dealer or authorised Service specified level (3 mm above the minimum level).
Centre to have the system inspected and any air
drained out of the circuit.

Warning
Brake and clutch fluid can damage paintwork
and plastic parts, so avoid contact.
Hydraulic oil is corrosive; it may cause damage and
lead to severe injuries. Never mix fluids of different
qualities. Check seals for proper sealing.

Clutch system
If the control lever has exceeding clearance and the
transmission snatches or jams as you try to engage
a gear, it means that there might be air in the circuit.
Contact your Ducati Dealer or authorised Service
Centre to have the system inspected and air drained
out.

209
Check brake pads for wear MIN
Check brake pads wear through the inspection hole
in the callipers. Change both pads if friction material
thickness of even just one pad is about 1 mm.

Warning
Friction material wear beyond this limit would
lead to metal support contact with the brake disc thus
compromising braking efficiency, disc integrity and
rider safety.

Important Fig. 129

Have the brake pads replaced at a Ducati Dealer
or authorised Service Centre.

MIN

Fig. 130
210
Charge the battery 1
Before charging the battery, it is best to remove it
from the motorcycle.
Remove the left-hand side fairing (page 204).
Undo the screw (1) and remove the battery mounting
cover (2).
Slide out the battery (3) from its housing and, always
starting from the negative terminal (-), loosen the
screws (4).
Remove the positive cable (5), the ABS positive cable
(6) from the positive terminal and the negative cable 2
(7) from the negative terminal.
Fig. 131

4 7 4 6

3
Fig. 132
211
 4
Warning
The battery produces explosive gases: keep it
away from heat sources

Warning
Keep the battery out of the reach of children.

Charge the battery at 0.9 A for 5÷10 hours.

Charge the battery in a ventilated room.
Connect the battery charger leads to the battery
terminals: the red one to the positive terminal (+), the
black one to the negative terminal (-). Fig. 133

5
Important
Make sure the charger is OFF when you
connect the battery to it, or you might get sparks at
the battery terminals that could ignite the gases
inside the cells. Always connect the red positive (+)
terminal first.

Lay down the ABS positive cable (6), onto positive

cable (5) and start screw (4) on these cables. 6

Fig. 134
212
Connect the positive cable (5), previously assembled
4 7
to ABS cable (6), to battery positive terminal, and
negative cable (7) to battery negative terminal, by
starting the other screw (4).
Tighten the terminal screws (4) to a torque of 5 Nm
±10% and apply grease onto the battery terminals to
prevent oxidation.
Reinstall the battery (3) in the support, positioning the
cables (5) and (6) as shown in (Fig. 132).
Refit battery mounting cover (2) and fasten tightening
the screw (1) to a torque of 10 Nm ±10%.
Refit the left-hand side fairing (page 204).
Fig. 135

2
Fig. 136
213
Charge and maintenance of the battery
during winter storage
Your motorcycle is equipped with a connector (1) to
which you can connect a special battery charger (2)
(Battery maintainer kit part no. 69924601A - various
countries; Battery maintainer kit part no.
69924601AX - for Japan, China and Australia only)
available from our sales network.

Note 1
The 899 Panigale electric system is designed so
as to ensure there is a very low power drain when the Fig. 137
motorcycle is OFF. Nevertheless, the battery
features a certain self-discharge rate that is normal
and depends on ambient conditions as well as on
"non-use" time.

2
Fig. 138
214
 Important
If battery is not kept at a minimum charge level
by a suitable battery charge maintainer, sulphation
may occur and this is an irreversible phenomenon
causing decreasing battery performance.

Note
When the motorcycle is left unused
(approximately for more than 30 days). we
recommend owners to use the Ducati battery charge
maintainer (Battery maintainer kit part no. 69924601A
- various countries; Battery maintainer kit part no.
69924601AX - for Japan, China and Australia only)
since its electronics monitors the battery voltage and
features a maximum charge current of 1.5 Ah.
Connect the maintainer to the diagnostics socket
located in the rear side of the motorcycle.

Note
Using charge maintainers not approved by
Ducati could damage the electric system; motorcycle
warranty does not cover the battery if damaged due
to failure to comply with the above indications, since
it is considered as wrong maintenance.

215
Check drive chain tension

Important
Have chain tension adjusted by a Ducati Dealer
or authorised Service Centre.

Make the rear wheel turn until you find the position
where chain is tightest. Set the motorcycle on the
side stand. With just a finger, push down the chain at 49÷51mm
the point of measurement and release.
Measure the distance (A) between the centre of the
chain pins and the aluminium section of the swinging
arm: it must be A = 49 ÷ 51 mm.

Important
This only applies to the motorcycle STANDARD A
settings, available upon delivery.

Important
If drive chain is too tight or slack, adjust tension
so as to bring values back to the specified range.

Fig. 139
216
 Warning 1
Correct tightening of swinging arm screws (1) is
critical to rider and passenger safety.

Important
Improper chain tension will lead to early wear of
transmission parts.

Check the correspondence of the positioning marks

on both sides of the swinging arm to ensure a perfect
wheel alignment.
Fig. 140

217
Chain lubrication
The chain fitted on your motorcycle has O-rings to
protect its moving parts from dirt, and to hold the
lubricant inside.
The seals might be irreparably damaged if the chain
is cleaned using any solvent other than those specific
for O-ring chains or washed using steam or water
cleaners.
After cleaning, blow the chain dry or dry it using
absorbent material and apply SHELL Advance Chain
or Advance Teflon Chain on each link.

Important
Using non-specific lubricants may cause severe
damage to the chain and the front and rear sprocket.

218
Replace the high and low beam bulbs
Before replacing a burnt-out bulb, make sure that the
new one matches the voltage and wattage HI HI
1
specifications in paragraph "Electric System" page
247.
Always ensure that the new bulb you have installed
operates properly before refitting any parts you have
removed. Figure shows the locations of the low beam LO
LO
bulbs (LO), high beam bulbs (HI) and the parking light
LED light unit (1).

Fig. 141

219
Headlight Replacing the parking light bulb
Obtain access to the left bulb. LED parking lights are maintenance-free.
Turn the locking ring of the upper bulb body counter
clockwise and extract the burnt out bulb. Rear turn indicators
Replace with a new bulb of the same type and rating. LED turn indicators are maintenance-free.
On refitting, turn the locking ring clockwise to secure
the bulb in place.
Obtain access to the right bulb and follow the same
procedure as for the left bulb to replace it.

Important
To replace the headlight bulbs, it is not
necessary to disconnect the main wiring harness
from headlight body.

Note
Be careful to hold the new bulb at the base only.
Never touch the transparent body with your fingers
or it will blacken resulting in reduced bulb brilliancy.

Warning
The headlight might fog up if the vehicle is used
under the rain or after washing. Switch headlight on
for a short time to dry up any condensate.

220
Beam setting
To check the headlight aim, place the motorcycle
upright with the tyres inflated to the correct pressure
and one person sitting astride the motorcycle. The
motorcycle should be perfectly vertical, with its
longitudinal axis at right angles to a wall or screen at 9 x x
a distance of 10 metres. then draw a horizontal line 10
dictated by headlamp centre and a vertical one in line
with the longitudinal axis of motorcycle. If possible,
10 m
perform this check in dim light. Switch on the low
beam and adjust the aiming of the left and right-hand
beams. The height of the upper limit between the
dark area and the lit area must not be more than nine Fig. 142
tenths of the height from ground of headlight centre.
Note
This is the procedure specified by Italian
regulations for checking the maximum height of the
light beam. Please adapt said procedure to the
provisions in force in your own country.

221
To adjust the headlight beam vertically, turn the
1
screws (1), located on the front, right and left side of
the vehicle.

Warning
The headlight might fog up if the vehicle is used
under the rain or after washing. Switch headlight on
for a short time to dry up any condensate.

Fig. 143

1
1

D U U D

Fig. 144
222
Adjust rear-view mirrors
The rear-view mirror can be adjusted manually by
pressing on point (A).

Fig. 145

223
Tubeless tyres In the event of a tiny puncture, tubeless tyres will take
Use on the road a long time to deflate, as they tend to keep air inside.
If you find low pressure on one tyre, check the tyre
Front tyre pressure: for punctures.
2.5 bar - 2.55 kg/sq. cm
Rear tyre pressure: Warning
2.5 bar - 2.55 kg/sq. cm Punctured tyres must be replaced. Replace
Use on the track tyres with recommended standard tyres only. Be
sure to tighten the valve caps securely to avoid leaks
Front tyre pressure: when riding. Never use tube type tyres. Failure to
2.3 bar - 2.35 kg/sq. cm heed this warning may lead to sudden tyre bursting
Rear tyre pressure: and to serious danger to rider and passenger.
2.1 bar - 2.14 kg/sq. cm
After replacing a tyre, the wheel must be balanced.
As tyre pressure is affected by ambient temperature
and altitude variations, you are advised to check and
adjust it whenever you are riding in areas where Warning
ample variations in temperature or altitude occur. Do not remove or shift the wheel balancing
weights.
Important
Check and adjust the pressures with the tyres
cold. To avoid front wheel box distortion, when riding
on bumpy roads, increase tyre pressure by 0.2 ÷ 0.3
bar.

Tyre repair or change (Tubeless tyres)

224
 Note
Have the tyres replaced at a Ducati Dealer or
authorised Service Centre. Correct removal and
installation of the wheels is essential. Some parts of
the ABS (such as sensors and phonic wheels) are
mounted to the wheels and require specific
adjustment.

225
Minimum tread depth
Measure tread depth (S,Fig. 146) at the point where
tread is most worn down: it should not be less than S
2 mm, and in any case not less than the legal limit.

Important
Visually inspect the tyres at regular intervals for
detecting cracks and cuts, especially on the side
walls, bulges or large spots that are indicative of
internal damage. Replace them if badly damaged.
Remove any stones or other foreign bodies caught in
the tread. Fig. 146

226
Check engine oil level
Engine oil level can be checked through the sight 1
glass (1) located onto clutch cover. Oil level must be
checked with the motorcycle perfectly upright and 2
the engine cold. Oil level should be between the
marks on the sight glass. If the level is low, top up
with SHELL Advance 4T Ultra engine oil. Remove the
oil filler cap (2) and top up until the oil reaches the
required level. Refit the plug.

Important
Engine oil and oil filters must be changed by a
Ducati Dealer or authorised Service Centre at the Fig. 147
intervals specified in the scheduled maintenance
chart reported in the Warranty Card.

227
Viscosity
SAE 15W-50 10W
The other viscosity degrees indicated in the table can 20W
be used if the local average temperature is within the

Unigrade
20
limits specified for that oil viscosity. 30
40

20W–40 20W–50

M ultigrade
15W–40 15W–50
10W–40
10W–30
–10 0 10 20 30 40 C

Fig. 148

228
Clean and replace the spark plugs
Spark plugs are essential to smooth engine running
and should be checked at regular intervals.
Have the spark plug replaced at a Ducati Dealer or
authorised Service Centre.

Fig. 149

229
Clean the motorcycle Important
To preserve the finish of metal parts and paintwork, Do not wash your motorcycle immediately after
wash and clean your motorcycle at regular intervals, use, as marks can form due to evaporation of the
anyway according to the road conditions you ride in. water on hot surfaces.
Use specific products only. Prefer biodegradable Never clean the motorcycle using hot or high-
products. Avoid aggressive detergents or solvents. pressure water jets.
Only use water and neutral soap to clean the Plexiglas Cleaning the motorcycle with a high pressure water
and the seat. jet may lead to seizure or serious faults in the front
Periodically manually clean all aluminium fork, wheel hub assembly, electric system, headlight
components. Use special detergents, suitable for (fogging), front fork seals, air inlets or exhaust
aluminium parts FREE of abrasives or caustic soda. silencers, with consequent loss of safety.
If parts of the engine are unusually dirty or greasy,
Note use a degreasing agent, avoiding contact with
Do not use sponges with abrasive parts or steel transmission components (chain, front and rear
wool: only use soft cloths. sprockets, etc.).

However, the warranty does not apply to motorcycles Rinse with warm water and dry all surfaces with
whenever poor maintenance status is ascertained. chamois leather.

Warning
Braking performance may be impaired
immediately after washing the motorcycle. Never
grease or lubricate the brake discs as this would
cause loss of braking effectiveness. Clean the discs
with an oil-free solvent.

230
 Warning - disconnect, remove the battery and periodically
The headlight might fog up due to washing, rain charge it using the battery charge maintainer (see
or moisture. Switch headlight on for a short time to page 214);
dry up any condensate. - Protect the motorcycle with a suitable canvas.
This will protect paintwork and let condensate
Carefully clean the phonic wheels of the ABS so to breathe out. The canvas is available from Ducati
ensure system efficiency. Do not use aggressive Performance.
products so to avoid damaging the phonic wheels and
the sensors.

Note
Do not use alcohol or alcohol-derived products
to clean the instrument panel.

Pay special attention to regularly clean the wheel rims

since they feature some machined aluminium parts;
clean and dry them any time you use the motorcycle.
Storing the motorcycle
If the motorcycle is to be left unridden over long
periods, it is advisable to carry out the following
operations before storing it away:
- clean the motorcycle;
- empty the fuel tank;
- place the motorcycle on a service stand;

231
Important notes
The legislation in some countries (France, Germany,
Great Britain, Europe, Switzerland, etc.) sets certain
noise and pollution standards.
Periodically carry out the required checks and replace
parts as necessary, using Ducati original spare parts,
in compliance with the regulations in the country
concerned.

232
Scheduled maintenance chart
Scheduled maintenance chart: operations to be performed by the Dealer

Warning
This scheduled maintenance chart is designed for a road use of the 899 Panigale. If it is used on the
track, even if not during sport competitions, all parts of the motorcycle are more stressed so the routine
maintenance operations must be carried out more frequently than indicated.

Warning
Please contact a Ducati Dealer or authorised Service Centre where you can receive customised service
advice according to the sport use you make of your 899 Panigale.

List of operations and type of interven- Km. x1,000 1 12 24 36 48

Time
tion
mi. x1,000 0.6 7.5 15 22.5 30 (months)
[set mileage (km/mi) or time interval *]
Read the error memory with DDS 2.0 and check whether
12
any update is available for control unit software version
Check whether there are technical updates and recall
12
campaigns
Change engine oil and filter 12
Clean engine oil mesh filter at intake -
Check and/or adjust valve clearance -

233
List of operations and type of interven- Km. x1,000 1 12 24 36 48
Time
tion
mi. x1,000 0.6 7.5 15 22.5 30 (months)
[set mileage (km/mi) or time interval *]
Visual check for wear of the chain timing system -
Replace the spark plugs -
Clean the air filter -
Change the air filter -
Check the proper tightening of the clutch cover and
-
clutch protection cover bolts
Check the proper tightening of the oil sump bolts -
Check brake and clutch fluid level 12
Change brake and clutch fluid 24
Check brake pads. Replace if necessary 12
Check the proper tightening of brake calliper bolts and
12
brake disc carrier bolts
Check front and rear wheel nuts tightening 12
Check wheel hub bearings -
Check and lubricate the rear wheel shaft 24
Check the cush drive damper on rear sprocket -

234
List of operations and type of interven- Km. x1,000 1 12 24 36 48
Time
tion
mi. x1,000 0.6 7.5 15 22.5 30 (months)
[set mileage (km/mi) or time interval *]
Check the proper tightening of secondary drive front and
12
rear sprocket nuts
Check chain sliders for wear 12
Check the drive chain tension and lubrication 12
Check steering bearings and lubricate, if necessary 24
Change the front fork fluid 36
Visually check the front fork and rear shock absorber
12
seals
Check the freedom of movement and tightening of the
12
side stand
Visually check the fuel lines 12
Check rubbing points, clearance, freedom of movement
and routing of the clearly visible flexible cables and elec- 12
tric wiring
Lubricate the levers at the handlebar and pedal controls 12
Change the coolant 36
Check the coolant level 12
Check electric fan operation 12

235
List of operations and type of interven- Km. x1,000 1 12 24 36 48
Time
tion
mi. x1,000 0.6 7.5 15 22.5 30 (months)
[set mileage (km/mi) or time interval *]
Check tyre pressure and wear 12
Check the battery charge level 12
Check idling 12
Check secondary air system operation -
Check the operation of all electric safety devices (side
stand sensor, front and rear brake switches, engine kill 12
switch, gear/neutral sensor)
Check the indicators and lighting 12
Reset the message "Service" through the DDS 2.0 12
Road test of the motorcycle, testing the safety devices
12
(e.g. ABS and DTC)
Cleaning the motorcycle 12
Fill out Warranty Certificate with service data 12

236
Scheduled maintenance chart: operations to be performed by the customer
Km. x1000 1
List of operations and type of intervention [set mileage (km/mi) or time
mi. x1000 0,6
interval *]
Months 6
Check engine oil level
Check brake and clutch fluid level
Check tyre pressure and wear
Check the drive chain tension and lubrication. If necessary, contact your dealer
to replace components.
Check brake pads. If necessary, contact your dealer to replace components.

* Service on the set interval, whichever comes first (mileage or months).

237
Technical data

Weights
Overall weight (in running order with 90% of fuel -
93/93/EC): 193 kg.
Overall weight (without fluids and battery): 169 kg.
Maximum allowed weight (carrying full load): 370 kg.

Warning
Failure to observe weight limits could result in
poor handling and impair the performance of your
motorcycle, and you may lose control of the
motorcycle.

238
Overall dimensions

730

644

1105
830
404
125

1430
2050

Fig. 150

239
Top-ups
TOP-UPS TYPE
Fuel tank, including a reserve of 5 cu. dm Unleaded fuel with a minimum octane rat- 17 cu. dm (litres)
(litres) ing of RON 95.
Oil sump and filter SHELL - Advance 4T Ultra 3.9 cu. dm (litres)
Front/rear brake and clutch circuits SHELL Advance Brake DOT 4 -
Protectant for electric contacts SHELL Advance Contact Cleaner -
Front fork SHELL Advance Fork 7.5 or Donax TA 563 ± 2 cu. cm , per leg
Cooling circuit ENI Agip Permanent Spezial antifreeze (do 2.3 cu. dm (litres)
not dilute, use pure)

Important
Do not use any additives in fuel or lubricants. Using them could result in severe damage of the engine
and motorcycle components.

Warning
The vehicle is only compatible with fuel having a maximum content of ethanol of 10% (E10).
Using fuel with ethanol content over 10% is forbidden. Using it could result in severe damage of the engine
and motorcycle components. Using fuel with ethanol content over 10% will make the warranty null and void.

240
Engine
Twin cylinder, four-stroke, 90° "L" type, longitudinal,
with deep sump die-cast crankcase.
Bore, mm: 100
Stroke, mm: 57.2
Total displacement, cu. cm : 898
Compression ratio: 12.5:1± 0.5
Max crankshaft power (95/1/EC), kW/HP:
109 kW/148 HP at 10,750 rpm
Max torque at crankshaft (95/1/EC):
99 Nm / 10.1Kgm / 73 lb-ft at 9,000 rpm
Maximum rpm:
11,500

Important
Do not exceed the specified rpm limits in any
running conditions.

241
Timing system 6 2 1
Double overhead camshaft (DOHC) driven by chain
and gearwheels, 4 valves per cylinder, desmodromic
system.
Desmodromic timing system 3
2
1) Opening (or upper) rocker 5
2) Opening rocker shim 1
4
3) Closing (or lower) rocker shim
4) Return spring for lower rocker
5) Closing (or lower) rocker 2 5 7
6) Camshaft
Fig. 151
7) Valve.

242
Performance data Warning
Maximum speed in any gear should be reached only The vehicle is only compatible with fuel having
after a correct running-in period with the motorcycle a maximum content of ethanol of 10% (E10).
properly serviced at the recommended intervals. Using fuel with ethanol content over 10% is
forbidden. Using it could result in severe damage of
Important the engine and motorcycle components. Using fuel
Failure to follow these instructions will release with ethanol content over 10% will make the
Ducati Motor Holding S.p.A. from any liability for any warranty null and void.
engine damage or shortened engine life.
Brakes
Spark plugs Separate-action anti-lock brake system operated by
Make: hall-type sensors mounted to each wheel with phonic
NGK wheel detection: ABS can be disabled.
Type: FRONT
MAR9A-J Semi-floating drilled twin-disc.
Braking material: steel.
Fuel system
Carrier material: aluminium.
MITSUBISHI indirect electronic injection
Carrier colour: black.
Oval throttle body (corresponding diameter):
Disc diameter: 320 mm.
62 mm
Hydraulically operated by a control lever on handlebar
Injectors per cylinder: 1
right-hand side.
Firing points per injector: 12
Brake calliper make: BREMBO.
Fuel specifications: 95-98 RON.
Type: M4.32b.
Friction material: TT2182FF.
Master cylinder type: PR18/21.

243
REAR 1st gear 15/37
With fixed drilled steel disc. 2nd gear 16/30
Disc diameter: 245 mm. 3rd gear 18/27
Hydraulically operated by a pedal on RH side. 4th gear 20/25
Make: BREMBO
5th gear 22/24
Type: P34e (calliper with Ø 34 pistons).
Friction material: Ferodo Ferit I/D 450 FF. 6th gear 24/23
Master cylinder type: PS 13. Drive chain from gearbox to rear wheel:.
Make: chain REGINA 520 ZRPK
Warning Links: 106
Brake fluid can dissolve paintwork.
In the event of accidental contact with eyes or skin, Important
wash the affected area with abundant running water. The above gear ratios are the homologated ones
and under no circumstances must they be modified.
Transmission
Wet clutch controlled by the lever on left-hand side However, if you wish to tune up your motorcycle for
of the handlebar competitions or special tracks, Ducati Motor Holding
Drive is transmitted from engine to gearbox main S.p.A. will be pleased to provide information about
shaft via spur gears. the special ratios available. Contact a Ducati Dealer or
Front chain sprocket/clutch gearwheel ratio: 30/53 Authorised Service Centre.
6-speed gearbox with constant mesh gears, gear
change pedal on left side of motorcycle.
Gearbox output sprocket/rear chain sprocket ratio:
15/44
Total gear ratios:

244
 Warning Rear
If the rear sprocket needs replacing, contact a Tubeless, radial tyre.
Ducati Dealer or authorised Service Centre. Size: 180/60.
Incorrect replacement of this component could Suspensions
seriously endanger rider and passenger safety and Front
cause irreparable damage to the motorcycle. Hydraulic upside-down fork with external adjusters
for rebound, compression, and preload (for inner
Frame springs of fork legs).
Cast monocoque frame in aluminium alloy. Stanchion diameter:
Rear steel tubular trellis sub-frame. 43 mm.
Steering head angle: 24° Wheel travel:
Steering angle: 27° LH side /27° RH side. 120 mm.
Trail: 96 mm.
Rear
Wheels The shock absorber is adjustable for rebound,
Front compression and spring preload.
5-spoke, light-alloy forged rims. The shock absorber is connected to the crankcase at
Size: MT3.50x17" the front pivot point and to the rocker arm at the rear
pivot point.
Rear
The swinging arm is connected to the pivot shafts
5-spoke, light-alloy forged rims.
going through the engine. The whole system gives
Size: MT5.50x17"
the motorcycle excellent stability.
Tyres Wheel travel:
Front 130 mm.
Tubeless, radial tyre.
Size: 120/70.
Exhaust system

245
Exhaust pipe layout is “2 into 1 into 2”.
Two stainless steel silencers with aluminium alloy
external sleeve.
Two lambda sensors and two catalytic converters.
Available colours
Ducati Anniversary red 473.101 (PPG);
Primer (White Acriflex) code LMC06017 (LECHLER);
sub-frame Matt Black 4 Gloss;
Monocoque Grey frame and black rims.
Arctic White Silk
Primer (Dual primer Arctic White) code L2920057
(Lechler);
Primer (Pearl White Ducati SF) code L2909004
(Lechler);
Clear coat 96598 (Lechler);
sub-frame Matt Black 4 Gloss;
Monocoque Grey frame and red rims.

246
Electrical system Electronic rectifier, protected by a 30A fuse located
Basic electric items are: on the solenoid starter, under the battery
Headlight with: (C, Fig. 154).
no. 2 bulbs H11 12V 55W (low beam); Starter motor: 12V-0.6 kW.
no. 2 bulbs H11 12V 55W (high beam). Number plate light: LED.
parking light type:
no. 8 Seoul STW8Q14B LEDs Note
Tail light type: For bulb replacement instructions, please read
no.2 REBEL LXM2-PH01-0060 LEDs. "Replacing the high and low beam bulbs".
LED stop lights type:
no.8 LA G6SP-CBEA-24-1 LEDs.
LED number plate light type:
no.3 CREE CLA1A-WKW-CXAYB453 LEDs.
Electrical controls on handlebars.
Front LED turn indicators, no. 15 LEDs
Rear LED turn indicators, no. 4 OSRAM LYE65F
LEDs.
Rear turn indicators, (USA) type: R10W (12V-10W)
Orange.
Horn.
Stop light switches.
Sealed battery, 12 V - 6.5 Ah.
System voltage 12 V.
GENERATOR 510W to 14V.

247
Fuses 7 8 9
There are twelve fuses that protect the electric
components, located inside the front fuse boxes, and
one on the electric solenoid starter. There is a spare A
fuse in every box.
Refer to the table below to identify the circuits
protected by the various fuses and their ratings.
The front left fuse box (A, Fig. 152) and the front right
one (B, Fig. 153) are located above the battery.
To access the fuses, remove the left fairing (page
204). 1 2 3 4 5 6
To expose the fuses, lift the box protective cover.
Fig. 152
Mounting position and ampere capacity are marked
on box cover.
9 8 7

1 2 3 4 5 6
Fig. 153
248
 Front left fuse box key Front right fuse box key
Pos El. item Rat. 5 ECU 10 A
1 - - 6 Black Box System 15 A
2 GPS 5A (BBS)

3 Key-sense 10 A 7 Spare 20 A

4 Diagnostics 5A 8 Spare 10 A

5 Throttle opening relay 10 A 9 Spare 5A

(ETV)
6 Instrument panel 10 A
7 Spare 5A
8 Spare 10 A
9 Spare 20 A

Front right fuse box key

Pos El. item Rat.
1 ABS 1 30 A
2 ABS 2 25 A
3 Injection relay 20 A
4 Lights 15 A

249
To access the main fuse, remove the left fairing (page
204). E
The main fuse (C, Fig. 154), is positioned next to the C D
battery, on the solenoid starter (D, Fig. 154). Remove
the fuse cap E, to reach it( Fig. 154). A blown fuse is
identified by the interrupted centre link (F, Fig. 155).

Important
Switch the ignition key to OFF before replacing
the fuse to avoid possible short-circuits.

Warning
Fig. 154
Never use a fuse with a rating other than
specified. Failure to observe this rule may damage
the electric system or even cause fire.
F F

Fig. 155
250
Injection /electric system diagram key 25) Fuel level
26) Vertical coil
1) Right-hand switch 27) Horizontal coil
2) E-LOCK control unit 28) Timing/rpm sensor
3) E-LOCK relay 29) Vertical lambda sensor
4) Fuse box 1 30) Horizontal lambda sensor
5) Fuse box 2 31) Quick shifter
6) ECU 32) Side stand switch
7) APS 33) Oil pressure sensor
8) Starter motor 34) Rear stop switch
9) Fused solenoid 35) Clutch switch
10) Battery 36) Front stop switch
11) Engine ground 37) Fuel pump relay
12) Regulator 38) Vertical ETV relay
13) Generator 39) Horizontal ETV relay
14) Rear right turn indicator 40) Vertical MAP sensor
15) Rear light 41) Horizontal MAP sensor
16) Rear left turn indicator 42) Water temperature sensor
17) Number plate light 43) Air temperature sensor
18) Diagnostics socket 44) Horizontal TPS
19) motorcycle control unit (BBS) 45) Vertical TPS
20) Ex-up drive 46) Main horizontal injector
21) Gear sensor 47) Main vertical injector
22) Rear speed sensor 48) Horizontal ETV drive
23) Front speed sensor 49) Vertical ETV drive
24) Fuel pump 50) Secondary air actuator

251
51) ABS control unit G Green
52) Left-hand switch Bn Brown
53) Horn O Orange
54) GPS P Pink
55) Front left turn indicator
56) Instrument panel Note
57) Left high beam The electric system wiring diagram is at the end
58) Left low beam of this manual.
59) Parking light
60) Right low beam
61) Right high beam
62) Front right turn indicator
63) Low beam relay
64) High beam relay
65) Fan

Wire colour coding

B Blue
W White
V Violet
Bk Black
Y Yellow
R Red
Lb Light blue
Gr Grey

252
Routine maintenance record
Routine maintenance record
KM NAME MILEAGE DATE
DUCATI SERVICE
1000
12000
24000
36000
48000
60000

253
Stampato 07/2014 Cod. 913.7.263.1A
 8 9 10
1 2 3 11 12

13
6
5 7

64 65

63 62
14

15
16

61 17
56
60 50

25

59 24 18

36 35 34 33
58 49 48 45 44
47 46 28
57 39 38 37

Vcc led immobilizer

19
55 32 31
43 42 41 40
54
27 26
53

30 29 23 22 21 20
52

51

899 Panigale
cod. 913.7.263.1A