Section 5 - Cased Fans - JM Aerofoil

JM Aerofoil Section 5.1

• Eleven sizes are offered from 315mm to • Low installed noise levels
1000mm diameter. • Motor protection IP55
• Volume flows of up to 19m3/s • All casings are hot dipped galvanised

Section 5 - Cased Fans - JM Aerofoil

• Static pressures up to 800 Pa • Overheat protection is fitted as standard
• High energy efficiency • Inverter controllable

Sizes
31JM - (315mm) to 100JM - (1000mm).
Larger sizes up to 2800mm diameter are also available. Please enquire.

Fan Performance
All fans are tested to the latest internationally recognised standard IS05801 Part 1 (1997), installation
category D (AMCA approved) for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance.
Coupled with a wide range of fan diameters, the adjustable pitch Aerofoil impeller gives the exact performance
required, with a non overloading fan characteristic.

Impellers
A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable
pitch angle availability.
The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise.
Every cast aluminium component is X-ray examined using Real Time Radiography inspection prior to assembly.
The maximum pitch angles shown allow for speed control by frequency inverter (3ph only).

Motors
All motors are totally enclosed air stream rated class F insulation. Constructed from aluminium or cast iron
as standard with special ‘T’ slot or pad mounted fixings. Single speed motors are suitable for speed control
by voltage regulation where indicated. Three phase motors are suitable for use with frequency inverters.
Two speed motors where available are pole change type.
Suitable for horizontal through to vertical shaft operation. Supplied IP55, with removable drain plugs.
Sealed for life bearings lubricated with wide temperature range grease. The BT, CT, F22 and PM112
motors are all fitted with overheat protection thermostat as standard. D motors are fitted with
Thermistor OHP.
These motors are suitable for inverter speed control down to 20% of full speed.

Electrical Supply
220 - 240V / 50Hz / 1φ
380 - 420V / 50Hz / 3φ

Temperature Range
-40°C to 50°C as standard. (All motors are not suitable for starting at temperatures
lower than -20°C.) Fans that include BT or CT motors can be continuously operated at
temperatures up to 70°C. When these fans are operating in excess of 50°C they should be run
at full speed only. Other fans can be operated up to 70°C with appropriate deration of motors.
Most standard 3φ fans can be offered for a one off emergency operation at 200˚C for 2 hours.

Casings
JM Aerofoil fans are available in either a long cased form, complete with an externally mounted pre-wired
electrical terminal box, or short cased for duct or plate installation. Casings are spun from sheet steel with integral
pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for
external as well as internal use.

Accessories
Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Air operated non
return dampers, Guards, Bell mouth inlets. Electronic and transformer type speed controllers and
frequency inverters.

Standards available contact your local Express

Distributor for more details. See section 5.3.

118
 Summary JM Aerofoil Data Section 5.1

220 - 240V / 50Hz / 1φ

Dia. Product Product Speed Sound Electronic m3/s at Pa (Static)

Section 5 - Cased Fans - JM Aerofoil

mm Code Number rev/min Level Speed

dBA Controller 0 50 100 150 200 250 300 400 500
315 31JM/16/4/5/36 DX321460 1420 44 N/A 0.65 0.54
315 31JM/16/2/5/30 DX321202 2840 61 N/A 1.15 1.11 1.06 0.99 0.94 0.86 0.78 0.59

355 35JM/16/4/5/40 DX361460 1420 49 ME1.1 1.00 0.86 0.63

355 35JM/16/2/5/34 JL361205 2840 64 N/A 1.73 1.70 1.63 1.56 1.45 1.40 1.31 1.12
400 40JM/16/4/5/40 DX411452 1420 52 ME1.3 1.50 1.31 1.06
400 40JM/16/2/5/22 JL411203 2840 66 N/A 2.33 2.26 2.19 2.11 2.05 1.97 1.72 1.67 1.42

450 45JM/16/4/5/30 JL461452 1420 57 ME1.3 1.80 1.61 1.40 1.11

450 45JM/16/4/5/40 DX461466 1420 56 ME1.3 2.20 1.95 1.72
450 45JM/16/2/5/14 JL461201 2840 66 N/A 2.50 2.45 2.40 2.30 2.20 2.10 2.05 1.85 1.6

500 50JM/16/4/5/28 DX511464 1420 57 ME1.6 2.75 2.50 2.21 1.85

500 50JM/16/4/5/40 JL511460 1420 59 ME1.6 3.00 2.75 2.43
500 50JM/20/4/6/20 DX511455 1420 53 ME1.3 1.85 1.70 1.50 1.25
500 50JM/20/4/6/32 DX511466 1420 56 ME1.6 2.60 2.41 2.20 1.95 1.60

560 56JM/16/4/5/22 JL571453 1420 57 ME1.6 2.90 2.70 2.35 2.10 1.65
560 56JM/16/4/5/28 DX571456 1420 58 ME1.6 3.40 3.15 2.85 2.55 2.10
560 56JM/20/4/6/28 DX571459 1420 57 ME1.6 3.46 3.24 3.00 2.74 2.42

630 63JM/20/6/6/20 JL641651 900 49 N/A 2.38 2.06 1.62

630 63JM/20/6/6/30 JL641652 900 52 ME1.6 3.24 2.85 2.32
630 63JM/20/4/6/16 DX641453 1420 61 ME1.6 3.45 3.30 3.10 2.90 2.65 2.25

Full selection details and dimensions see section 5.1.

Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Quick selection guide to the JM Cased Aerofoil fans available

Express Range - These products are available from our UK Express Distributor on same day delivery
from the date of order.

Standard Service - Please consult your local distributor for availability maximum 15 days.

119
Summary JM Aerofoil Data Section 5.1

380 - 420V / 50Hz / 3φ

Dia. Product Product Speed Sound Electronic m3/s at Pa (Static)

Section 5 - Cased Fans - JM Aerofoil

mm Code Number rev/min Level Speed Inverter
dBA Controller 0 50 100 150 200 250 300 400 500 600 800
315 31JM/16/4/5/40 DX341460 1420 44 ME3.5S FWD1 0.67 0.55
315 31JM/16/2/5/34 DX341202 2840 61 N/A FWD1 1.25 1.18 1.15 1.06 1.01 0.93 0.85

355 35JM/16/4/5/40 DX381460 1420 49 ME3.5S FWD1 1.00 0.86 0.63

355 35JM/16/2/5/32 DX381210 2840 64 N/A FWD1 1.73 1.70 1.63 1.56 1.45 1.40 1.31 1.12

355 35JM/16/2/5/40 JL381204 2840 66 N/A FWD2 2.00 1.93 1.90 1.82 1.73 1.65 1.55 1.27

400 40JM/16/4/5/40 DX431452 1420 52 ME3.2D FWD1 1.50 1.31 1.06

400 40JM/16/2/5/32 DX431203 2840 66 N/A FWD2 2.60 2.51 2.42 2.35 2.27 2.18 2.08 1.86 1.61

450 45JM/16/4/5/30 JL481452 1420 52 ME3.2D N/A 1.80 1.61 1.40 1.11

450 45JM/16/4/5/40 DX481460 1420 56 ME3.2D FWD1 2.20 1.95 1.72

450 45JM/16/2/5/20 JL481202 2840 66 N/A N/A 2.65 2.60 2.54 2.48 2.40 2.31 2.20 2.02 1.80

450 45JM/20/2/6/34 EX481205 2910 72 N/A FWD4 3.85 3.80 3.70 3.60 3.52 3.40 3.31 3.12 2.90 2.70

500 50JM/16/4/5/34 DX531460 1420 57 ME3.2D FWD1 2.75 2.50 2.21 1.85

500 50JM/16/4/5/40 JL531454 1420 59 AT7.0 N/A 3.00 2.75 2.43

500 50JM/20/4/6/20 JL531456 1420 53 N/A N/A 1.85 1.70 1.50 1.25

500 50JM/20/4/6/28 DX531462 1420 56 ME3.2D FWD1 2.60 2.41 2.20 1.95 1.60

500 50JM/20/4/6/40 JL531458 1420 58 AT7.0 N/A 2.97 2.77 2.51 2.20

500 50JM/20/2/6/24 EX531203 2840 70 N/A FWD4 4.30 4.22 4.18 4.05 4.00 3.90 3.80 3.62 3.42 3.22 2.60

500 50JM/20/2/6/34 DX531204 2840 74 N/A FWD6 5.52 5.48 5.35 5.27 5.20 5.09 4.92 4.75 4.45 4.22 3.60

560 56JM/16/4/5/24 JL591452 1420 57 ME3.2D N/A 3.05 2.82 2.55 2.22 1.82

560 56JM/16/4/5/28 DX591453 1420 58 AT7.0 FWD1 3.73 3.42 3.23 2.80 2.38

560 56JM/20/4/6/32 DX591458 1420 61 ME3.2D FWD2 4.05 3.82 3.60 3.21 2.90

560 56JM/20/2/6/24 EX591201 2910 73 N/A FWD6 6.30 6.20 6.10 6.05 5.90 5.85 5.70 5.46 5.20 5.08 4.35

630 63JM/20/6/6/20 JL661651 900 49 ME3.2D N/A 2.51 2.20 1.75

630 63JM/20/6/6/30 JL661652 900 50 ME3.2D N/A 3.55 3.10 2.50

630 63JM/20/4/6/20 DX661453 1420 61 ME3.2D FWD2 4.05 3.8 3.6 3.4 3.1 2.85

630 63JM/20/4/6/32 DX661454 1420 61 AT7.0 FWD2 5.30 5.10 4.81 4.55 4.15 3.82

710 71JM/20/6/6/18 JL741652 900 53 ME3.2D FWD1 3.75 3.55 3.00

710 71JM/20/6/6/36 EX741653 900 55 N/A FWD2 5.55 4.90 4.20

710 71JM/20/4/6/36 DX741404 1440 64 N/A FWD5 6.1 5.8 5.6 5.4 5.2 4.8 4.5

710 71JM/20/4/6/24 EX741401 1440 65 N/A FWD3 6.45 6.20 6.00 5.75 5.50 5.22 4.87

710 71JM/20/4/6/24 JL741451 1440 67 N/A FWD3 6.48 6.22 5.98 5.74 5.49 5.21 4.88

800 80JM/20/6/6/28 EX831651 935 58 N/A FWD2 6.60 5.70 5.20 4.50

800 80JM/20/6/6/36 JL831452 935 60 N/A FWD3 7.90 7.25 6.50 5.60

800 80JM/20/4/6/24 JL831412 1440 69 N/A FWD5 9.41 9.00 8.51 8.18 7.82 7.40 6.90

800 80JM/25/4/9/22 EX831405 1440 71 N/A FWD5 8.50 8.10 7.90 7.60 7.40 7.00 6.60 6.00

800 80JM/25/4/9/26 EX831408 1440 71 N/A FWD6 9.50 9.25 9.00 8.70 8.40 8.05 7.60 6.90

900 90JM/25/8/9/32 JL931802 695 58 N/A FWD2 8.20 7.32 6.25

900 90JM/25/6/6/32 JL933602 935 65 N/A FWD2 9.60 9.00 8.15 7.10

900 90JM/25/6/9/24 JL931602 935 63 N/A FWD3 8.50 8.05 7.55 7.05 6.55 5.70

900 90JM/25/4/9/24 EX931403 1440 74 N/A FWD7 12.50 12.10 12.00 11.50 11.10 10.70 10.40 10.00 8.90

900 90JM/25/4/9/30 EX931406 1440 75 N/A FWD8 16.20 15.20 14.80 14.40 14.00 13.70 13.30 12.40 11.80

1000 100JM/25/8/9/24 JL131802 695 61 N/A FWD2 8.80 7.90 6.70

1000 100JM/25/6/6/18 EX133652 950 68 N/A FWD3 10.80 9.90 8.10 6.90

1000 100JM/25/6/9/34 JL131609 960 71 N/A FWD6 15.40 14.60 14.00 13.00 12.00 10.80

1000 100JM/25/4/6/22 EX133402 1450 79 N/A FWD7 16.20 15.90 15.20 14.70 14.10 13.80 13.10 11.70 10.00

1000 100JM/25/4/9/22 JL131419 1470 79 N/A FWD8 16.50 16.00 15.50 15.10 14.90 14.30 13.90 12.80 11.60

1000 100JM/25/4/9/28 EX131405 1470 79 N/A FWD9 18.80 18.28 17.75 17.48 17.20 16.30 15.40 14.50 13.60

Full selection details and dimensions see section 5.1.

Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

120
 Aerofoil fan 31JM - 35JM Section 5.1

4 Pole 2 Pole

31JM/16/4/5/... 35JM/16/4/5/... 31JM/16/2/5/... 35JM/16/2/5/...

Section 5 - Cased Fans - JM Aerofoil

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400
31JM/16/4/5/40 1420 0.67 0.55
31JM/16/2/5/34 2840 1.25 1.18 1.15 1.06 1.01 0.93 0.85
35JM/16/4/5/40 1420 1.00 0.86 0.63
35JM/16/2/5/34 2840 1.73 1.70 1.63 1.56 1.45 1.40 1.31 1.12
35JM/16/2/5/40 2840 2.00 1.93 1.9 1.82 1.73 1.65 1.55 1.27

Electrical Data

220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
31JM/16/4/5/... 1420 BT5 DX321460 28-36 0.075 0.53 1.45 CD1705 N/A N/A 44
31JM/16/2/5/... 2840 BT9 DX321202 24-28 0.48 3.1 6.7 CD1705 N/A N/A 61
35JM/16/4/5/... 1420 BT4 DX361460 30-40 0.13 1.05 1.75 CD1705 ME1.3 MT1.5 49
35JM/16/2/5/... 2840 CT9 JL361205 32-34 1.0 6.8 21 CD1705 ME1.12 MT1.8 64

380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA

31JM/16/4/5/40 1420 BT4 DX341460 40-40 0.13 0.50 1.15 CD1344 ME3.5S MT3.0.5 FWD1 44
31JM/16/2/5/34 2840 BT9 DX341202 8-34 0.58 1.45 5.7 CD1344 N/A N/A FWD1 61
35JM/16/4/5/40 1420 BT5 DX381460 36-40 0.18 0.63 1.85 CD1344 ME3.5S MT3.1 FWD1 49
35JM/16/2/5/32 2840 CT5 DX381210 8-32 0.95 2.5 8 CD1344 N/A N/A FWD1 64
35JM/16/2/5/40 2840 CT9 JL381204 8-40 1.6 3.8 17.5 CD1344 N/A N/A FWD2 66

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented
for comparative purposes only.

Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.

When these fans are operating in excess of 50°C they should be run at full speed only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

Wiring diagram references can be found in section 9.2. Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

121
Aerofoil fan 31JM - 35JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)

Long Cased
31JM BT4/5 315 395 330 235 2.0 25 175 355 66 245 265 315 10 200 8 10 - 0.8 23
31JM BT9 315 395 375 235 2.5 25 175 355 66 290 265 315 10 200 8 10 - 0.8 27
35JM BT4/CT5 355 435 330 256 2.0 25 200 395 66 245 305 355 10 225 8 10 - 1.1 24
35JM CT9 355 435 375 256 2.5 25 200 395 66 290 305 355 10 225 8 10 - 1.1 28
Short Cased
31JM BT4/5 315 395 301 225 2.5 - - 355 - - - - - - 8 10 - - 13.5
31JM BT9 315 395 333 225 2.5 - - 355 - - - - - - 8 10 - - 15
35JM BT4/5 355 435 301 225 2.5 - - 395 - - - - - - 8 10 - - 14
35JM CT5 355 435 308 225 2.5 - - 395 - - - - - - 8 10 - - 16.5
35JM CT9 355 435 348 225 2.5 - - 395 - - - - - - 8 10 - - 20.5

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which covers all accessories).

122
 Aerofoil fan 40JM - 45JM Section 5.1

4 Pole 2 Pole

40JM/16/4/5/... 45JM/16/4/5/... 40JM/16/2/5/... 45JM/16/2/5/... 45JM/20/2/6/...

Section 5 - Cased Fans - JM Aerofoil

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400 500 600
40JM/16/4/5/40 1420 1.50 1.31 1.06
40JM/16/2/5/32 2840 2.60 2.51 2.42 2.35 2.27 2.18 2.08 1.86 1.61
45JM/16/4/5/30 1420 1.80 1.61 1.40 1.1
45JM/16/4/5/40 1420 2.20 1.95 1.72
45JM/16/2/5/20 2840 2.65 2.60 2.54 2.48 2.40 2.31 2.20 2.02 1.80
45JM/20/2/6/34 2910 3.85 3.80 3.70 3.60 3.52 3.40 3.31 3.12 2.90 2.70

Electrical Data
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
40JM/16/4/5/… 1420 BT9 DX411452 36-40 0.32 2.2 5 CD1705 ME1.3 MT1.5 52
40JM/16/2/5/… 2840 CT9 JL411203 18-22 1 6.8 21 CD1705 N/A N/A 66
45JM/16/4/5/… 1420 BT9 JL461452 24-30 0.32 2.2 5 CD1705 ME1.3 MT1.5 52
45JM/16/4/5/… 1420 CT5 DX461466 32-40 0.39 2.9 5.6 CD1705 ME1.3 MT1.5 56
45JM/16/2/5/… 2840 CT9 JL461201 10-14 1 6.8 21 CD1705 N/A N/A 66

380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA

40JM/16/4/5/… 1420 BT9 DX431452 34-40 0.29 0.97 3 CD1559 ME3.2D MT3.1 FWD1 52
40JM/16/2/5/… 2840 CT9 DX431203 8-32 1.6 3.8 17.5 CD1344 N/A N/A FWD2 66

45JM/16/4/5/… 1420 BT9 JL481452 8-34 0.39 1.26 3.9 CD1559 N/A N/A FWD1 52
45JM/16/4/5/… 1420 CT5 DX481460 36-40 0.52 1.7 4.7 CD1559 ME3.2D MT3.2 FWD1 56
45JM/16/2/5/… 2840 CT9 JL481202 8-20 1.6 3.8 17.5 CD1344 N/A N/A FWD2 66
45JM/20/2/6/… 2840 F22 EX481205 8-34 3.8 7.21 64 CD1343 N/A N/A FWD4 72

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented
for comparative purposes only.

Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.

When these fans are operating in excess of 50°C they should be run at full speed only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

Wiring diagram references can be found in section 9.2. Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

123
Aerofoil fan 40JM - 45JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)
Long Cased
40JM BT9:CT9 400 480 375 279 2.5 25 225 450 66 290 350 400 10 250 8 12 - 1.2 30
45JM CT5 450 530 330 306 2.0 25 225 500 66 245 400 450 10 280 8 12 - 1.5 32
45JM BT9:CT9 450 530 375 306 2.5 25 225 500 66 290 400 450 10 280 8 12 - 1.5 32
45JM F22 450 530 520 306 3 25 255 500 66 434 400 450 10 280 8 12 - 1.5 50
Short Cased
40JM BT9 400 480 333 225 2.5 - - 450 - - - - - - 8 12 - - 16.5
40JM CT9 400 480 348 225 2.5 - - 450 - - - - - - 8 12 - - 21
45JM BT9 450 530 333 225 2.5 - - 500 - - - - - - 8 12 - - 18.5
45JM CT9 450 530 348 225 2.5 - - 500 - - - - - - 8 12 - - 23
45JM F22 450 530 444 225 3 - - 500 - - - - - - 8 12 - - 40

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which shows all accessories).

124
 Aerofoil fan 50JM Section 5.1

4 Pole 2 Pole

50JM/16/4/5/... 50JM/20/4/6/... 50JM/ 20/2/6/... †56JM/20/2/6/...

Section 5 - Cased Fans - JM Aerofoil

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400 500 600
50JM/16/4/5/34 1420 2.75 2.50 2.21 1.85
50JM/16/4/5/40 1420 3.00 2.75 2.43
50JM/20/4/6/20 1420 1.85 1.70 1.50 1.25
50JM/20/4/6/32 1420 2.60 2.41 2.20 1.95 1.60
50JM/20/4/6/40 1420 2.97 2.77 2.51 2.20
50JM/20/2/6/24 2840 4.30 4.22 4.18 4.05 4.00 3.90 3.80 3.62 3.42 2.60
50JM/20/2/6/34 2840 5.52 5.48 5.35 5.27 5.20 5.09 4.92 4.75 4.45 3.60

† For tabular data of 56JM 2 Pole see page 127

Electrical Data
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
50JM/16/4/5/… 1420 CT5 DX511464 32-34 0.52 3.9 7.8 CD1705 ME1.6 MT1.5 57
50JM/16/4/5/… 1420 CT9 JL511460 34-40 0.68 4.8 11 CD1705 ME1.6 MT1.5 59
50JM/20/4/6/… 1420 BT9 DX511455 16-20 0.32 2.2 5 CD1705 ME1.3 MT1.5 53
50JM/20/4/6/… 1420 CT5 DX511466 28-32 0.52 3.9 7.8 CD1705 ME1.6 MT1.5 56

380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA

50JM/16/4/5/… 1420 CT5 DX531460 26-30 0.54 1.8 4.9 CD1559 ME3.2D MT3.2 FWD1 57
50JM/16/4/5/… 1420 CT9 JL531454 34-40 0.83 2.30 8.6 CD1559 N/A AT7.0 FWD1 59
50JM/20/4/6/… 1420 BT9 JL531456 8-20 0.39 1.26 3.9 CD1559 N/A N/A FWD1 53
50JM/20/4/6/… 1420 CT5 DX531462 24-28 0.54 1.8 4.9 CD1559 ME3.2D MT3.2 FWD1 56
50JM/20/4/6/… 1420 CT9 JL531458 32-38 0.83 2.30 8.6 CD1559 N/A AT7.0 FWD1 58
50JM/20/2/6/… 2840 F22 EX531203 8-24 3.8 7.21 64 CD1343 N/A N/A FWD4 70
50JM/20/2/6/… 2840 PM112 DX531204 8-34 6.2 11.64 100 CD1343 N/A N/A FWD6 74

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented for comparative purposes only.

Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.

When these fans are operating in excess of 50°C they should be run at full speed only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

Wiring diagram references can be found in section 9.2. Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

125
Aerofoil fan 50JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)
Long Cased
50JM CT5 500 594 330 338 2.0 25 290 560 66 235 450 500 10 315 12 12 - 2.0 30
50JM BT9:CT9 500 594 375 338 2.5 25 290 560 66 280 450 500 10 315 12 12 - 2.0 34
50JM F22/PM112 500 594 520 338 3 25 290 560 66 424 450 500 10 315 12 12 - 2.0 67
Short Cased
50JM BT9 500 594 333 225 2.5 - - 560 - - - - - - 12 12 - - 20
50JM CT5 500 594 308 225 2.5 - - 560 - - - - - - 12 12 - - 20.5
50JM CT9 500 594 348 225 2.5 - - 560 - - - - - - 12 12 - - 25
50JM F22 500 594 444 225 3 - - 560 - - - - - - 12 12 - - 43
50JM PM112 500 594 392 225 3 - - 560 - - - - - - 12 12 - - 50

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which shows all accessories).

126
 Aerofoil fan 56JM - 63JM Section 5.1

6 Pole 4 Pole

63JM/20/6/6/... 56JM/20/4/6/... 63JM/20/4/6/...

Section 5 - Cased Fans - JM Aerofoil

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400 500 600
56JM/16/4/5/24 1420 3.05 2.82 2.55 2.22 1.82
56JM/16/4/5/32 1420 3.73 3.42 3.23 2.80 2.38
56JM/20/4/6/36 1420 4.05 3.82 3.60 3.21 2.90
56JM/20/2/6/24 2910 6.30 6.20 6.10 6.05 5.90 5.85 5.70 5.46 5.20 4.35
63JM/20/6/6/22 900 2.51 2.2 1.75
63JM/20/6/6/34 900 3.55 3.10 2.50
63JM/20/4/6/18 1420 3.45 3.30 3.10 2.90 2.65 2.25
63JM/20/4/6/32 1420 5.30 5.10 4.81 4.55 4.15 3.82

† For graphical data of 56JM 2 Pole see page 125

Electrical Data
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
56JM/16/4/5/… 1420 CT5 JL571453 18-20 0.52 3.9 7.8 CD1705 ME1.6 MT1.5 57
56JM/16/4/5/… 1420 CT9 DX571456 26-32 0.97 6.7 13.5 CD1705 ME1.6 MT1.8 58
56JM/20/4/6/... 1420 CT9 DX571459 26-28 0.97 6.7 13.5 CD1705 ME1.6 MT1.8 58
63JM/20/6/6/... 900 CT5 JL641651 16-20 0.29 2.3 4.1 CD1705 N/A N/A 49
63JM/20/6/6/... 900 CT9 JL641652 26-30 0.53 0.38 6.8 CD1705 ME1.6 MT1.8 52
63JM/20/4/6/… 1420 CT9 DX641453 14-16 0.97 6.7 13.5 CD1705 ME1.6 MT1.8 61

380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
56JM/16/4/5/… 1420 CT5 JL591452 16-24 0.54 1.8 4.9 CD1343 ME3.2D MT3.2 FWD1 57
56JM/16/4/5/… 1420 CT9 DX591453 24-28 0.83 2.30 8.6 CD1343 N/A AT7.0 FWD1 58
56JM/20/4/6/… 1420 CT9 DX591458 28-32 1.15 3.2 11 CD1343 ME3.2D AT7.0 FWD2 61
56JM/20/2/6/… 2910 PM112 EX591201 8-24 6.2 11.64 100 CD1343 N/A N/A FWD6 73
63JM/20/6/6/… 900 CT5 JL661651 16-20 0.3 1.02 2.35 CD1559 ME3.2D MT3.2 FWD1 49
63JM/20/6/6/… 900 CT9 JL661652 26-30 0.5 1.5 4.5 CD1559 ME3.2D MT3.2 FWD1 50
63JM/20/4/6/… 1420 CT9 DX661453 18-20 1.15 3.2 11 CD1559 ME3.2D AT7.0 FWD2 61
63JM/20/4/6/… 1420 F22 DX661454 24-32 2.1 5 27 CD1343 N/A AT7.0 FWD2 61

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented for comparative purposes only.

Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.

When these fans are operating in excess of 50°C they should be run at full speed only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

127
Aerofoil fan 56JM - 63JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)
Long Cased
56JM CT 560 654 375 368 2.5 25 330 620 66 280 510 560 10 355 12 12 - 2.3 38
56JM F22 560 654 520 368 3 25 330 620 66 424 510 560 10 355 12 12 - 2.3 62
63JM CT 630 724 375 403 3 25 375 690 66 289 580 630 10 400 12 12 - 2.4 52
63JM F22/PM112 630 724 520 403 3 25 375 690 66 434 580 630 10 400 12 12 - 2.4 83
Short Cased
56JM CT5 560 654 308 225 2.5 - - 620 - - - - - - 12 12 - - 22
56JM CT9 560 654 348 225 2.5 - - 620 - - - - - - 12 12 - - 26
56JM PM112 560 654 392 225 3 - - 620 - - - - - - 12 12 - - 52
63JM CT5 630 724 308 225 3 - - 690 - - - - - - 12 12 - - 36
63JM CT9 630 724 348 225 3 - - 690 - - - - - - 12 12 - - 40
63JM F22 630 724 444 225 3 - - 690 - - - - - - 12 12 - - 56

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which shows all accessories).

Wiring diagram references can be found in section 9.2.

Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

128
 Aerofoil fan 71JM - 80JM Section 5.1

6 Pole 4 Pole

71JM/20/6/6/... 80JM/20/6/6/... 71JM/20/4/6/... 80JM/20/4/6/... 80JM/25/4/9/...

Section 5 - Cased Fans - JM Aerofoil

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400
71JM/20/6/6/18 900 3.28 2.96 2.53
71JM/20/6/6/36 900 5.55 4.90 4.20
71JM/20/4/6/24 1440 6.45 6.20 6.00 5.75 5.50 5.22 4.87
71JM/20/4/6/36 1440 8.7 8.4 8.0 7.6 7.2 6.8 6.3
80JM/20/6/6/28 935 6.60 5.70 5.20 4.50
80JM/20/6/6/36 935 7.90 7.25 6.50 5.60
80JM/20/4/6/24 1440 9.41 9.00 8.51 8.18 7.82 7.40 6.90
80JM/25/4/9/22 1440 8.50 8.10 7.90 7.60 7.40 7.00 6.60 6.00
80JM/25/4/9/26 1440 9.50 9.25 9.00 8.70 8.40 8.05 7.60 6.90

Electrical Data
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
71JM/20/6/6/… 900 CT9 JL741652 16-18 0.5 1.5 4.5 CD1559 ME3.2D MT3.2 FWD1 53
71JM/20/6/6/… 900 F22 EX741653 24-36 1.35 3.4 15 CD1559 N/A AT7.0 FWD2 55
71JM/20/4/6/… 1440 F22 EX741401 8-24 2.7 5.77 30 CD1343 N/A N/A FWD3 65
71JM/20/4/6/... 1440 F22 JL741451 20-24 2.7 5.77 30 CD1599 N/A AT7.0 FWD3 65
71JM/20/4/6/… 1440 PM112 DX741404 8-36 4.4 9.3 55 CD1343 N/A N/A FWD5 68
80JM/20/6/6/… 935 F22 EX831651 24-28 1.35 3.4 15 CD1559 N/A AT7.0 FWD2 58
80JM/20/6/6/… 935 F22 JL831452 8-36 2.5 6.42 26 CD1343 N/A N/A FWD3 60
80JM/20/4/6/… 1440 PM112 JL831412 8-24 4.4 9.33 55 CD1343 N/A N/A FWD5 69
80JM/25/4/9/… 1440 PM112 EX831405 8-22 4.4 9.33 55 CD1343 N/A N/A FWD5 71
80JM/25/4/9/… 1440 *D132S EX831408 8-26 6.6 12.6 84.4 CD1343 N/A N/A FWD6 71

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented
for comparative purposes only.

Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.

When these fans are operating in excess of 50°C they should be run at full speed only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

* OHP = Thermistor. Maximum pitch angle at 200° = 24°.

Wiring diagram references can be found in section 9.2. Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

129
Aerofoil fan 71JM - 80JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)
Long Cased
71JM CT9 710 804 375 443 3 25 415 770 66 259 660 710 10 440 16 12 - 4.5 54
71JM F22/PM112 710 804 520 443 3 25 415 770 66 404 660 710 10 440 16 12 - 4.5 87
80JM F22/PM112 800 894 520 488 3 25 485 860 66 404 750 800 10 510 16 12 - 5.8 96
80JM D132 800 894 520 525 5 25 485 860 66 400 750 800 12 510 16 12 - 5.8 192
Short Cased
71JM CT9 710 804 348 225 3 - - 770 - - - - - - 16 12 - - 42
71JM F22 710 804 444 225 3 - - 770 - - - - - - 16 12 - - 59
71JM PM112 710 804 392 225 3 - - 770 - - - - - - 16 12 - - 66
80JM F22 800 894 444 225 3 - - 860 - - - - - - 16 12 - - 65
80JM PM112 800 894 392 225 3 - - 860 - - - - - - 16 12 - - 72
80JM D132 800 894 445 260 4 - - 860 - - - - - - 16 12 - - 174

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which shows all accessories).

130
 Aerofoil fan 90JM - 100JM Section 5.1

8 Pole 6 Pole

90JM/25/8/9/... 100JM/25/8/9/... 90JM/25/6/6/... 100JM/25/6/6/... 100JM/25/6/9/...

Section 5 - Cased Fans - JM Aerofoil

4 Pole

90JM/25/4/9/... 100JM/25/4/9/...

Product Speed m3/s at Pa (Static)

Code rev/min 0 50 100 150 200 250 300 400 500
90JM/25/8/9/32 695 7.9 7.0 6.1
90JM/25/6/6/32 935 9.60 9.00 8.15 7.10
90JM/25/6/9/24 935 8.50 8.05 7.55 7.05 6.55 5.70
90JM/25/4/9/22 1440 12.5 12.1 12.0 11.5 11.1 10.7 10.4 10.0 8.9
90JM/25/4/9/30 1440 16.2 15.2 14.8 14.4 14.0 13.7 13.3 12.4 11.8
100JM/25/8/9/22 695 8.6 7.4 6.3
100JM/25/6/6/22 950 10.8 9.9 9.0 8.1 6.9
100JM/25/6/9/34 960 15.4 14.6 14.0 13.0 12.0 10.8
100JM/25/4/6/22 1470 16.2 15.9 15.2 14.7 14.1 13.8 13.1 11.7 10.0
100JM/25/4/9/22 1470 17.7 17.2 16.8 16.3 15.8 15.4 14.9 13.9 12.7
100JM/25/4/9/28 1470 20.9 20.4 20.0 19.6 19.1 18.6 18.1 17.0 15.7

Electrical Data
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Angle Rating Current Current Diagram Sound
rev/min 200˚C (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (˚) (kW) (A) (A) tronic former dBA
90JM/25/8/9/… 695 F22 JL931802 8-32 30 1.4 4.93 18 CD1343 N/A N/A FWD2 58
90JM/25/6/6/… 935 F22 JL933602 8-32 28 2.5 6.42 26 CD1343 N/A N/A FWD3 65
90JM/25/6/9/… 935 F22 JL931602 8-24 24 2.5 6.42 26 CD1343 N/A N/A FWD3 63
90JM/25/4/9/… 1440 *D132M EX931403 8-24 20 9 12.6 84.4 CD1343 N/A N/A FWD7 74
90JM/25/4/9/… 1440 *D160M EX931406 8-32 28 13.2 25.4 127 CD1343 N/A N/A FWD8 75
100JM/25/8/9/… 695 F22 JL131802 8-22 22 1.4 4.93 18 CD1343 N/A N/A N/A 61
100JM/25/6/6/… 950 F22 EX133652 16-18 18 2.1 5.74 24 CD1343 N/A AT7.0 FWD3 68
100JM/25/6/9/… 960 *D132M JL131609 8-34 18 6.6 14.3 78.7 CD1343 N/A N/A FWD6 71
100JM/25/4/6/… 1450 *D132M EX133402 8-22 18 9 12.6 84.4 CD1343 N/A N/A FWD7 79
100JM/25/4/9/… 1470 *D160M JL131419 8-22 18 13.2 25.4 127 CD1343 N/A N/A FWD8 79
100JM/25/4/9/… 1470 *D160L EX131405 8-28 26 18 34.8 171 CD1343 N/A N/A FWD9 79

Sound pressure levels quoted are average dBA at 3m distance over a sphere, under free field conditions and are presented for comparative purposes only.

For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Product numbers shown are for Long cased fans.

* OHP = Thermistor, Please refer to our Fläkt Woods inverter & speed control warranty clause on page 226.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

131
Aerofoil fan 90JM - 100JM Section 5.1

Dimensions

Section 5 - Cased Fans - JM Aerofoil

Long Cased

Short Cased

Product Motor A B C D E F G H J K L M N P S T U X Max. Fan

Code Range Weight (kg)

Long Cased
90JM F22 900 1006 520 538 3 25 491 970 66 444 850 900 10 518 16 15 - 5.3 94
90JM D132 900 1006 520 575 5 25 491 970 66 440 850 900 12 518 16 15 - 5.3 206
90JM D160 900 1006 711 575 5 25 491 970 66 629 850 900 12 518 16 15 - 5.3 270
100JM F22 1000 1106 520 588 3 25 547 1070 66 444 950 1000 10 574 16 15 - 6.2 102
100JM D132 1000 1106 520 588 5 25 547 1070 66 440 950 1000 10 574 16 15 - 6.2 227
100JM D160 1000 1106 711 625 6 25 547 1070 66 629 950 1000 12 574 16 15 - 6.2 286
Short Cased
90JM F22 900 1006 444 225 3 - - 970 - - - - - - 16 15 - - 67
90JM D132 900 1006 445 300 5 - - 970 - - - - - - 16 15 - - 138
90JM D160 900 1006 609 300 5 - - 970 - - - - - - 16 15 - - 276
100JM F22 1000 1106 444 225 3 - - 1070 - - - - - - 16 15 - - 72
100JM D132 1000 1106 445 300 5 - - 1070 - - - - - - 16 15 - - 153
100JM D160 1000 1106 575 300 5 - - 1070 - - - - - - 16 15 - - 217

All dimensions shown in mm.

For a full range of accessories including silencers, speed controllers and mountings,
please refer to section 5.10 or 9.1 (which shows all accessories).

Wiring diagram references can be found in section 9.2.

132
 Cased Accessories Section 5.10

JM – Matching Flanges and Flexible Connector

Suitable Product Numbers Weight (kg)
Section 5 - Cased Fans - JM Accessories

for fan Matching Flexible C Matching Flexible

OA Flange Connector Flange Connection
315 DA408238 DA414865 110 1.1 3.3
355 DA501351 DA414866 110 1.3 3.9
400 DA074913 DA414867 110 1.5 4.5
450 DA501353 DA414868 110 1.7 5.0
500 DA074914 DA414869 110 2.0 5.5
560 DA501355 DA414901 110 2.3 6.8
630 DA074915 DA414844 160 3.0 7.5
710 DA074916 DA414845 160 3.2 8.1
800 74917 414846 160 3.6 9.1
900 404841 414847 160 4.1 10.4
1000 74918 414848 160 4.6 11.6

Note: Flexible Connection weight includes two Matching Flanges.

Suitable for up to 600˚C emergency operation for 2 hours and
200˚C continuous.

JM Damper
Suitable for Product Weight
C D
fan OA Number kg
315 414942 225 – 8
355 414943 225 – 9
400 414944 225 17 10
450 414945 225 39 12
500 414473 225 75 16
560 414474 225 125 18
630 414475 225 176 20
710 414476 225 210 23
800 414477 225 270 27
900 414478 225 305 31
1000 414479 225 345 36

Note: Suitable for up to 400˚C emergency operation and 200˚C continuous.

JM Mounting Feet
Product Product Frame
G L M N P T V W
Code Number Size
315 DA408199 BT/CT.F22 175 265 315 10 200 10 20 60
355 DA408200 BT/CT.F22 200 305 355 10 225 10 20 60
400 DA408201 BT/CT.F22 225 350 400 10 250 12 20 60
450 DA408202 BT/CT,F22 255 400 450 10 280 12 20 60
500 DA408203 BT/CT,F22 290 450 500 10 315 12 25 65
560 DA408204 BT/CT,F22 330 510 560 10 355 12 25 65
630 DA243495 BT/CT,F22 375 580 630 10 400 14 25 65
710 DA245874 BT/CT,F22 415 660 710 10 440 14 25 80
800 245024 BT/CT,F22 485 750 800 12 510 14 25 80
800 249468 D132 485 750 800 1 510 14 25 80
900 249467 F22 491 850 900 12 518 14 25 60
900 249258 D132 491 850 900 12 518 14 25 60
1000 249464 F22 547 950 1000 10 574 15 25 60
1000 249255 D132 547 50 1000 12 574 15 25 60

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

163
Cased Accessories Section 5.10

JM – Cylindrical Silencers

Section 5 - Cased Fans - JM Accessories

Acoustic Performance B Type (without Pod)
Acoustic Performance (dB) – Octave Band Mid Frequency – Hz
Bore Dia.
Length
mm (D)
63 125 250 500 1K 2K 4K 8K

315 1D 1 2 4 9 11 10 9 7
355 1D 1 2 4 10 12 10 9 7
400 1D 2 3 5 10 13 11 9 8
450 1D 2 3 6 12 13 11 10 6
500 1D 2 3 6 13 14 10 10 5
560 1D 2 4 7 14 14 19 10 7
630 1D 2 5 7 15 13 8 9 8
710 1D 3 5 7 15 13 9 9 8
800 1D 3 5 8 16 12 9 9 8
900 1D 3 5 10 17 13 11 10 8
1000 1D 4 5 11 16 11 10 8 9

Acoustic Performance C Type (with Pod)

Acoustic Performance (dB) – Octave Band Mid Frequency – Hz
Bore Dia.
Length
mm (D)
63 125 250 500 1K 2K 4K 8K

315 1D 2 5 5 9 18 20 18 15
355 1D 2 5 6 9 18 22 19 16
400 1D 2 6 6 10 19 24 20 17
450 1D 2 4 7 13 20 23 22 17
500 1D 2 3 8 16 21 22 21 17
560 1D 3 5 8 16 20 18 19 15
630 1D 3 5 8 15 19 16 14 12
710 1D 3 5 8 15 19 15 14 12
800 1D 4 5 8 16 19 15 14 13
900 1D 4 5 9 17 19 15 14 13
1000 1D 5 5 11 18 19 15 14 13

Silencer

The above silencers give the following approximate dBA reductions:

B Type 1 diameter length – 7 to 10 dBA C Type 1 diameter length – 12 to 15 dBA.
For full acoustic details and resistance to airflow for type C see publication SPO1.

Suitable Product Numbers Weight (kg)

for fan B Type C Type
OA (Pod Kit) B C J B Type C Type
315 DS211401 DA415792 415 315 M8 ID 13
355 DS221401 DA415793 455 355 M8 12 15
400 DS241401 DA415794 500 400 M10 15 18
450 DS251401 DA415795 600 450 M10 20 24
500 DS271401 DA415796 650 500 M10 25 29
560 DS281401 DA415797 710 560 M10 30 35
630 DS301401 DA415798 780 630 M10 35 42
710 DS311401 DA415799 860 710 M10 44 53
800 331401 416212 1000 800 M10 55 66
900 341401 416213 1100 900 M12 70 84
1000 351401 416214 1200 1000 M12 82 100

164
 Cased Accessories Section 5.10

Guard – JM Aerofoil Suitable

for fan φA
Type C Weight

315 I 137 1.2

315 IV 30 0.5
Section 5 - Cased Fans - JM Accessories

355 I 137 1.4

355 IV 30 0.5
400 I 137 1.6
400 IV 30 0.6
450 I 137 1.8
450 II 137 1.6
450 IV 30 0.6
500 I 137 2.0
500 II 137 1.8
500 IV 30 0.7
560 I 137 2.2
560 II 137 2.0
560 IV 50 1.0
630 I 137 2.8
630 II 137 2.6
630 III 350 3.0
Type I & Type Type III Type IV 630 IV 50 1.2

II 710 I 137 3.2

Motor Side Bellmouth & 710 II 137 3.0
Impeller Side S Type L Type 710 III 350 3.4

L & S Type Motor Side 710 IV 50 1.4

(D132 & D160) 800 I 137 3.5

Motor Side 800 II 137 3.3

S Type 800 III 350 3.9

800 IV 50 1.5

(BT, CT & F22) 900 I 137 4.2

900 II 137 4.2
900 III 310 4.8
900 IV 50 1.7
1000 I 137 5.0
Type II guards have a Ø220 hole cut out of centre. 1000 II 137 4.8
1000 III 310 5.6
1000 IV 50 2.0

JM Bell Mouth Inlet – Fan with flanged inlet only

Suitable Product Numbers C D Weight (kg)

for fan φA
315 408593 65 379 1.0
355 248950 85 423 1.2
400 74880 80 480 1.5
450 248952 95 536 2.0
500 74881 87 600 3.2
560 248953 100 668 4.0
630 74882 108 757 4.8
710 74883 126 857 5.4
800 74884 134 957 6.8
900 404842 150 1077 8.0
1000 74885 167 1199 17.8

All dimensions shown in mm.

Express Range - These products are available from our UK Express Distributor on same day
delivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.

165
Cased Accessories Section 5.10

Diffuser & Grille – Axcent 2

Section 5 - Cased Fans - JM Accessories

D
Diffuser Grille
C
Weight Weight
A B C (kg) D (kg)

315 400 225 10 43 1

400 500 280 15 55 1

500 630 355 23 68 2

ØB 630 800 450 37 95 3

ØA

800 1000 560 56 108 4

1000 1250 710 85 134 5

1120 1400 800 136 150 6

1250 1600 900 143 168 7

166