Residues (petroleum), vacuum.

CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND COMPANY/UNDERTAKING

Material Name : Residues (petroleum), vacuum. CAS 64741-56-6

Recommended Use / : Paving grade bitumen for road paving.
Restrictions of Use

Supplier : Shell Eastern Trading (PTE) Ltd

9 North Buona Vista Drive,

#07-01,
Tower 1, The Metropolis
Singapore 138588
Singapore

Telephone : +65-6384 8000

Emergency Telephone : +44 (0) 151 350 4595
Number

2. HAZARDS IDENTIFICATION

GHS Classification : Not classified

GHS Label Elements

Symbol(s) :
No symbol
Signal Words : No signal word

Hazard Statement : PHYSICAL HAZARDS:

Not classified as a physical hazard under GHS criteria.

HEALTH HAZARDS:
Not classified as a health hazard under GHS criteria.

ENVIRONMENTAL HAZARDS:
Not classified as an environmental hazard under GHS criteria.

GHS Precautionary Statements

Prevention : No precautionary phrases.

Response : No precautionary phrases.

Storage : No precautionary phrases.

Disposal: : No precautionary phrases.

1/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Other Hazards which do : Not classified as flammable but will burn. Do not allow molten
not result in classification material to contact water or liquids as this can cause violent
eruptions, splatter hot material, or ignite flammable material.
These deposits, (carbonaceous materials and iron sulphides),
may be pyrophoric and self-ignite when brought into contact
with air (opening of tank). Hydrogen sulphide (H2S), an
extremely flammable and toxic gas, and other hazardous
vapours may evolve and collect in the headspace of storage
tanks, transport vessels and other enclosed containers.
Hydrogen sulphide is highly toxic and may be fatal if inhaled.
May dull the sense of smell and has a high odour threshold, so
do not rely on odour as an indication of hazard. Contact with
hot material can cause thermal burns which may result in
permanent skin damage. Hot product may cause severe eye
burns and/or blindness.

3. COMPOSITION/INFORMATION ON INGREDIENTS

Mixture Description : A blend of components derived from crude petroleum oil.

CAS No. : 64741-56-6

Classification of components according to GHS

Chemical Identity Synonyms CAS Hazard Class Hazard Conc.
(category) Statement
Residues Residues 64741-56-6 None, None; None; 0.00 -
(petroleum), (petroleum), 100.00 %
vacuum vacuum

Additional Information : Contains hydrogen sulphide, CAS # 7783-06-4.

Hydrogen sulphide may be present both in the liquid and the

vapour. Composition is complex and varies with the source of
the crude oil.

4. FIRST-AID MEASURES

General Information : DO NOT DELAY. Keep victim calm. Obtain medical treatment
immediately.
Inhalation : If inhalation of mists, fumes or vapour causes irritation to the
nose or throat, remove to fresh air. If rapid recovery does not
occur, obtain medical attention. Casualties suffering ill effects
as a result of exposure to hydrogen sulphide should be
2/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

removed to fresh air. Do not attempt to rescue the victim

unless proper respiratory protection is worn. If the victim has
difficulty breathing or tightness of the chest, is dizzy, vomiting,
or unresponsive, give 100% oxygen with rescue breathing or
Cardiopulmonary Resuscitation (CPR) as required and
transport to the nearest medical facility.
Skin Contact : If contact with hot product, immediately cool the burn area by
flushing or immersing the affected area with water for at least
15 to 20 minutes. Do not attempt to remove anything from the
burn area or apply burn creams or ointments. During transport
do not cover the wound with dressing or sheet since these may
adhere to the product. It should be noted this product contracts
on cooling. Where a limb is encased, care should be taken to
avoid the development of a tourniquet effect. In the event of
this occurring, the adhering product must be softened and/or
split to prevent restriction of blood flow. All burns should
receive medical attention.
Eye Contact : Hot product - If contact with hot product, immediately cool the
burn area by flushing or immersing the affected area with water
for at least 15 to 20 minutes. Do not attempt to remove
anything from the burn area or apply burn creams or ointments.
During transport do not cover the wound with dressing or sheet
since these may adhere to the product. Transport to the
nearest medical facility for additional treatment. Cold product -
Flush eye with copious quantities of water. If persistent
irritation occurs, obtain medical attention.
Ingestion : Under normal conditions of use, this is not expected to be a
primary route of exposure.
Most Important : H2S has a broad range of effects dependent on the airborne
Symptoms/Effects, Acute concentration and length of exposure: 0.02 ppm odour
& Delayed threshold, smell of rotten eggs; 10 ppm eye and respiratory
tract irritation; 100 ppm coughing, headache, dizziness,
nausea, eye irritation, loss of sense of smell in minutes; 200
ppm potential for pulmonary oedema after >20-30 minutes; 500
ppm loss of consciousness after short exposures, potential for
respiratory arrest; >1000ppm immediate loss of consciousness,
may lead rapidly to death, prompt cardiopulmonary
resuscitation may be required. Do not depend on sense of
smell for warning. H2S causes rapid olfactory fatigue
(deadens sense of smell). There is no evidence that H2S will
accumulate in the body tissue after repeated exposure.
Immediate medical : Do not attempt to remove the product from the skin as it
attention, special provides an airtight sterile covering, which will eventually fall
treatment away with the scab as the burn heals. If removal is attempted,
mineral oil (not mineral spirits) or a mineral oil based ointment
may be applied to help soften the product to facilitate removal.
3/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Hydrogen sulphide (H2S) - CNS asphyxiant. May cause

rhinitis, bronchitis and occasionally pulmonary oedema after
severe exposure. CONSIDER: Oxygen therapy. Consult a
Poison Control Center for guidance.

5. FIRE-FIGHTING MEASURES

Clear fire area of all non-emergency personnel.

Specific hazards arising : Hazardous combustion products may include: A complex

from Chemicals mixture of airborne solid and liquid particulates and gases
(smoke). Carbon monoxide. Unidentified organic and inorganic
compounds. Boil-over of tanks and violent eruptions may occur
in the presence of water.
Suitable Extinguishing : Foam, water spray or fog. Dry chemical powder, carbon
Media dioxide, sand or earth may be used for small fires only.
Unsuitable Extinguishing : Do not use water in a jet.
Media
Protective Equipment & : Proper protective equipment including chemical resistant
Precautions for Fire gloves are to be worn; chemical resistant suit is indicated if
Fighters large contact with spilled product is expected. Self-Contained
Breathing Apparatus must be worn when approaching a fire in
a confined space. Select fire fighter's clothing approved to
relevant Standards (e.g. Europe: EN469).

6. ACCIDENTAL RELEASE MEASURES

Avoid contact with spilled or released material. For guidance on selection of personal protective
equipment see Chapter 8 of this Material Safety Data Sheet. See Chapter 13 for information on
disposal.

Personal Precautions, : Avoid contact with skin, eyes and clothing. Hot product should
Protective Equipment and be handled so that there is no risk of burns. Use compressed
Emergency Procedures air or fresh air respiratory equipment in confined spaces.
Environmental : Prevent from spreading or entering into drains, ditches or rivers
Precautions by using sand, earth, or other appropriate barriers.
Methods and Material for : Small spillage:
Containment and Allow product to cool and solidify. Shovel into a suitable clearly
Cleaning Up marked container for disposal or reclamation in accordance
with local regulations. Large spillage:
Prevent from spreading by making a barrier with sand, earth or
other containment material. Treat residues as for small
spillage.
Additional Advice : Local authorities should be advised if significant spillages
4/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

cannot be contained. For guidance on selection of personal

protective equipment see Chapter 8 of this Material Safety
Data Sheet. For guidance on disposal of spilled material see
Chapter 13 of this Material Safety Data Sheet.

7. HANDLING AND STORAGE

General Precautions : Avoid contact with hot liquid to prevent thermal burns.

Precautions for Safe : For quality, health and safety reasons do not exceed the
Handling recommended storage and handling temperature. Clean, dry
and heat resistant hoses (free of twists, etc.) should be used.
Do not use steam to empty pipelines and hoses. Use
compressed air to blow product from the system or apply a
vacuum to suck the product from the system. Do not use
solvents to clear obstructions of pipelines. Use local exhaust
ventilation if there is risk of inhalation of vapours, mists or
aerosols. Bulk storage tanks should be diked (bunded).
Conditions for Safe : Keep dry. Keep container in a well-ventilated place. Prevent all
Storage contact with water and with moist atmosphere. In case of long-
term storage, deposits may develop on walls and roofs of
storage tanks. These deposits, (carbonaceous materials and
iron sulphides), may be pyrophoric and self-ignite when
brought into contact with air (opening of tank). Hydrogen
sulphide may accumulate in tanks during long term storage at
high temperatures. For this reason, tank vapour spaces should
be regarded as hazardous. Refer to section 15 for any
additional specific legislation covering the packaging and
storage of this product. Storage Temperature: Temperature
should be kept at least 30°C below flash point and should
never exceed the industry recommended maximum safe
working temperature of 200°C.
Recommended Materials : For containers or container linings, use stainless steel.
Unsuitable Materials : For containers or container linings avoid PVC, polyethylene or
high density polyethylene.
Precautions During : Tanks may be heated by hot oil, steam, electricity or flame
Discharge from Bitumen tubes. When pumping product from a storage or road tank,
Tanks care should be taken to avoid the risk of fire or explosion as a
result of exposing hot heater tubes. The tubes should be
covered by a minimum of 150mm of hot product, unless the
heat has been switched off for a period of sufficient cooling.
Bulk temperature should be kept as low as possible, to enable
efficient discharge. A check should be made to ensure that the
receiving tank has sufficient ullage space to accommodate the
load.
5/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Other Advice : The inherent toxic and olfactory (sense of smell) fatiguing
properties of hydrogen sulphide require that air monitoring
alarms be used if concentrations are expected to reach harmful
levels such as in enclosed spaces, heated transport vessels
and spill or leak situations. If the air concentration exceeds 10
ppm, the area should be evacuated unless respiratory
protection is in use.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

If the American Conference of Governmental Industrial Hygienists (ACGIH) value is provided on

this document, it is provided for information only.

Occupational Exposure Limits

Material Source Type ppm mg/m3 Notation

Residues ACGIH TWA(Inhala 0.5 mg/m3 as benzene
(petroleum), ble fraction.) solubles
vacuum

SG OEL TWA(Fume. 5 mg/m3

)

Hydrogen ACGIH TWA 1 ppm

Sulphide

ACGIH STEL 5 ppm

SG OEL TWA 10 ppm 14 mg/m3

SG OEL STEL 15 ppm 21 mg/m3

Additional Information : Product has a low volatility and at ambient temperature fume
formation will be low. Avoid vapours from heated materials to
prevent exposure to potentially toxic/irritating fumes.

Biological Exposure Index (BEI)

No biological limit allocated.

Appropriate Engineering : The level of protection and types of controls necessary will vary

6/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Controls depending upon potential exposure conditions. Select controls

based on a risk assessment of local circumstances.
Appropriate measures include: Where material is heated,
sprayed or mist formed, there is greater potential for airborne
concentrations to be generated. Always observe good personal
hygiene measures, such as washing hands after handling the
material and before eating, drinking, and/or smoking. Routinely
wash work clothing and protective equipment to remove
contaminants. Discard contaminated clothing and footwear that
cannot be cleaned. Practice good housekeeping. Define
procedures for safe handling and maintenance of controls.
Educate and train workers in the hazards and control
measures relevant to normal activities associated with this
product. Ensure appropriate selection, testing and
maintenance of equipment used to control exposure, e.g.
personal protective equipment, local exhaust ventilation. Drain
down system prior to equipment break-in or maintenance.
Retain drain downs in sealed storage pending disposal or for
subsequent recycle.
Individual Protection : Personal protective equipment (PPE) should meet
Measures recommended national standards. Check with PPE suppliers.

Respiratory Protection : No respiratory protection is ordinarily required under normal

conditions of use. In accordance with good industrial hygiene
practices, precautions should be taken to avoid breathing of
material. Use self contained breathing apparatus in places
where hydrogen sulphide vapours may accumulate.
Hand Protection : Where hand contact with the product may occur the use of
gloves approved to relevant standards (e.g. Europe: EN374,
US: F739) made from the following materials may provide
suitable chemical protection: Heat resistant gloves and PVC or
nitrile rubber gloves. Suitability and durability of a glove is
dependent on usage, e.g. frequency and duration of contact,
chemical resistance of glove material, dexterity. Always seek
advice from glove suppliers. Contaminated gloves should be
replaced. For continuous contact we recommend gloves with
breakthrough time of more than 240 minutes with preference
for > 480 minutes where suitable gloves can be identified. For
short-term/splash protection we recommend the same, but
recognise that suitable gloves offering this level of protection
may not be available and in this case a lower breakthrough
time may be acceptable so long as appropriate maintenance
and replacement regimes are followed. Glove thickness is not
a good predictor of glove resistance to a chemical as it is
dependent on the exact composition of the glove material.
Eye Protection : Chemical splash goggles (gas-tight monogoggles) and face
7/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

shield with chin guard.

Protective Clothing : Chemical and heat resistant gloves, boots, and apron.
Thermal Hazards : When handling heated product, wear heat resistant gloves,
safety hat with visor, and heat resistant coveralls (with cuffs
over gloves and legs over boots), and heavy-duty boots, e.g.
leather for heat resistance.
Monitoring Methods : Monitoring of the concentration of substances in the breathing
zone of workers or in the general workplace may be required to
confirm compliance with an OEL and adequacy of exposure
controls. For some substances biological monitoring may also
be appropriate. Validated exposure measurement methods
should be applied by a competent person and samples
analysed by an accredited laboratory. Examples of sources of
recommended exposure measurement methods are given
below or contact the supplier. Further national methods may be
available.

National Institute of Occupational Safety and Health (NIOSH),

USA: Manual of Analytical Methods http://www.cdc.gov/niosh/
Occupational Safety and Health Administration (OSHA), USA:
Sampling and Analytical Methods http://www.osha.gov/
Environmental Exposure : Local guidelines on emission limits for volatile substances must
Controls be observed for the discharge of exhaust air containing vapour.
Take appropriate measures to fulfil the requirements of
relevant environmental protection legislation. Avoid
contamination of the environment by following advice given in
Chapter 6. If necessary, prevent undissolved material from
being discharged to waste water. Waste water should be
treated in a municipal or industrial waste water treatment plant
before discharge to surface water.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance : Brown to black. Liquid at high temperatures.

Odour : Characteristic
Odour threshold : Data not available
pH : Not applicable.
Initial Boiling Point and : > 320 °C / 608 °F
Boiling Range
Melting / freezing point : Data not available
Flash point : > 230 °C / 446 °F (Cleveland Open Cup)
Upper / lower : Data not available
Flammability or
Explosion limits
Auto-ignition temperature : > 300 °C / 572 °F
Vapour pressure : < 1 hPa
8/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Relative Density : Data not available

Density : ca. 0.990 - 1.300 g/cm3 at 25 °C / 77 °F
Water solubility : Negligible.
Solubility in other : Soluble.
solvents

n-octanol/water partition : Data not available

coefficient (log Pow)
Dynamic viscosity : Data not available
Kinematic viscosity : Data not available
Vapour density (air=1) : Not applicable.
Electrical conductivity : This material is not expected to be a static accumulator.
Evaporation rate : Not applicable.
(nBuAc=1)
Hygroscopicity : Negligible.
Decomposition : Data not available
Temperature
Flammability : Not applicable.

10. STABILITY AND REACTIVITY

Chemical stability : No hazardous reaction is expected when handled and stored

according to provisions.
Possibility of Hazardous : Data not available
Reactions
Conditions to Avoid : Heating above the maximum recommended storage and
handling temperature, will cause degradation and evolution of
flammable vapours.
Incompatible Materials : Do not allow molten material to contact water or liquids as this
can cause violent eruptions, splatter hot material, or ignite
flammable material. Reacts with strong oxidising agents. Avoid
contamination of thermal insulation near hot surfaces by oil and
bitumen and replace lagging where necessary, with a non-
absorbent type of insulation. Self-heating, leading to auto-
ignition at the surfaces of porous or fibrous materials
impregnated with bitumen or condensates from bituminous
fumes, can occur at temperatures below 100°C.
Hazardous : Hydrogen sulphide.
Decomposition Products
Sensitivity to Mechanical : Not applicable.
Impact
Sensitivity to Static : No, product cannot ignite due to static electricity.
Discharge

9/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

11. TOXICOLOGICAL INFORMATION

Information on Toxicological effects

Basis for Assessment : Information given is based on product testing, and/or similar
products, and/or components. Unless indicated otherwise, the
data presented is representative of the product as a whole,
rather than for individual component(s).
Likely Routes of : Skin and eye contact are the primary routes of exposure
Exposure although exposure may occur through inhalation or following
accidental ingestion. Inhalation is not expected to be a relevant
route of exposure except under conditions where exposure to
vapours, aerosols or mists is possible.
Acute Oral Toxicity : Low toxicity: LD50 > 5000 mg/kg , Rat

Acute Dermal Toxicity : Expected to be of low toxicity: LD50 >2000 mg/kg , Rabbit

Acute Inhalation Toxicity :

Skin corrosion/irritation : Expected to be slightly irritating. Contact with hot material can
cause thermal burns which may result in permanent skin
damage.

Serious eye : Expected to be slightly irritating. Hot product may cause severe
damage/irritation eye burns and/or blindness.

Respiratory Irritation : Inhalation of vapours or mists may cause irritation to the

respiratory system.

Respiratory or skin : Not expected to be a sensitiser.

sensitisation
Aspiration Hazard : Not considered an aspiration hazard.

Germ cell mutagenicity : Not considered a mutagenic hazard.

Carcinogenicity : Bitumens contain low concentrations of Polycyclic Aromatic

Compounds (PACs). At ambient temperatures and in undiluted
bitumens these PACs are not considered to be bio-available.
However, if bitumens are mixed with diluents to obtain a low
viscosity at ambient temperatures, or heated it is believed that
such materials may become bio-available. A two-year
inhalation study that exposed rats to fumes collected from an
air-rectified asphalt was negative.

Material : Carcinogenicity Classification

10/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Residues (petroleum), : ACGIH Group A4: Not classifiable as a human carcinogen.

vacuum
Residues (petroleum), : IARC 2B: Occupational exposures to hard bitumens and their
vacuum emissions during mastic asphalt work are ‘possibly
carcinogenic to humans’ (IARC Group 2B)., Occupational
exposures to straight-run bitumens and their fume condensates
during road paving are ‘possibly carcinogenic to humans’
(IARC Group 2B).
Residues (petroleum), : GHS / CLP: No carcinogenicity classification
vacuum
Hydrogen Sulphide : GHS / CLP: No carcinogenicity classification

Reproductive and : Not expected to impair fertility. Not expected to be a

Developmental Toxicity developmental toxicant.

Specific target organ : Inhalation of vapours or mists may cause irritation to the
toxicity - single exposure respiratory system.

Specific target organ : Not expected to be a hazard.

toxicity - repeated
exposure
Additional Information : Classifications by other authorities under varying regulatory
frameworks may exist.

12. ECOLOGICAL INFORMATION

Basis for Assessment : Incomplete ecotoxicological data are available for this product.
The information given below is based partly on a knowledge of
the components and the ecotoxicology of similar products.
Unless indicated otherwise, the data presented is
representative of the product as a whole, rather than for
individual component(s).

Acute Toxicity : Poorly soluble mixture. May cause physical fouling of aquatic
organisms. Expected to be practically non toxic: LL/EL/IL50 >
100 mg/l (to aquatic organisms) LL/EL50 expressed as the
nominal amount of product required to prepare aqueous test
extract.
Fish : Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l
Aquatic crustacea : Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l
Algae/aquatic plants : Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l
Microorganisms : Expected to be practically non toxic: LL/EL/IL50 > 100 mg/l
Chronic Toxicity

11/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Fish : NOEC/NOEL expected to be > 100 mg/l (based on modeled

data)
Aquatic crustacea : NOEC/NOEL expected to be > 100 mg/l (based on modeled
data)
Mobility : Adsorbs to soil and has low mobility. In water will either float or
sink, showing little tendency to disperse, the product will
adsorb to the sediment.
Persistence/degradability : Expected to be not readily biodegradable.
Bioaccumulative : Has the potential to bioaccumulate.
Potential
Other Adverse Effects : Not expected to have ozone depletion potential, photochemical
ozone creation potential or global warming potential.

13. DISPOSAL CONSIDERATIONS

Material Disposal : Recover or recycle if possible. It is the responsibility of the

waste generator to determine the toxicity and physical
properties of the material generated to determine the proper
waste classification and disposal methods in compliance with
applicable regulations. Do not dispose into the environment, in
drains or in water courses.
Container Disposal : Dispose in accordance with prevailing regulations, preferably to
a recognised collector or contractor. The competence of the
collector or contractor should be established beforehand.
Local Legislation : Disposal should be in accordance with applicable regional,
national, and local laws and regulations.

14. TRANSPORT INFORMATION

Land (as per ADR classification): Regulated

Class : 9
Packing group : III
Hazard indentification no. : 99
UN number : 3257
Danger label (primary risk) : 9
Proper shipping name : ELEVATED TEMPERATURE LIQUID, N.O.S. (Bitumen)
Environmentally Hazardous : No

IMDG
Identification number UN 3257
Proper shipping name ELEVATED TEMPERATURE LIQUID, N.O.S.
Technical name (Bitumen)
Class / Division 9
Packing group III
12/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

Marine Pollutant: No

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Pollution Category : Not applicable.
Ship Type : Not applicable.
Product Name : Not applicable.
Special Precaution : Not applicable.
Additional Information : IATA - Forbidden for transport on passenger and cargo aircraft
in molten state.
Not dangerous for conveyance under UN, IMO, ADR/RID,
IATA codes if transported at ambient temperature.
MARPOL Annex 1 rules apply for bulk shipments by sea.

15. REGULATORY INFORMATION

The regulatory information is not intended to be comprehensive. Other regulations may apply to this
material.

Local Regulations
Workplace Safety and : This product is subject to the SDS, Labelling, PEL and other
Health Act & Workplace requirements in the Act/ Regulations.
Safety and Health (General
Provision) Regulations
Environmental Protection : This product is not subject to the requirement in the
and Management Act and Act/Regulations.
Environmental Protection
and Management
(Hazardous Substances)
Regulations
Maritime and Port Authority : This product is not subject to the requirement in the
of Singapore (Dangerous Act/Regulations.
Goods, Petroleum and
Explosives) Regulations
Fire Safety Act and Fire : This product is not subject to the requirement in the
Safety (Petroleum & Act/Regulations.
Flammable Materials)
Regulations

Other Information : Environmental Protection and Management Act. Workplace

Safety and Health Act 2006.

13/14
Print Date 16.04.2014 000000023457
MSDS_SG
 Residues (petroleum), vacuum. CAS 64741-56-6
Version 1.1
Effective Date 10.03.2014

Safety Data Sheet

16. OTHER INFORMATION

SDS Version Number : 1.1

SDS Effective Date : 10.03.2014

SDS Revisions : A vertical bar (|) in the left margin indicates an amendment
from the previous version.
Uses and Restrictions : This product must not be used in applications other than those
recommended in Section 1, without first seeking the advice of
the supplier.

SDS Distribution : The information in this document should be made available to

all who may handle the product.
Key Literature References : The quoted data are from, but not limited to, one or more
sources of information (e.g. toxicological data from Shell Health
Services, material suppliers’ data, CONCAWE, EU IUCLID
date base, EC 1272 regulation, etc).

Disclaimer : This information is based on our current knowledge and is

intended to describe the product for the purposes of health,
safety and environmental requirements only. It should not
therefore be construed as guaranteeing any specific property
of the product.

14/14
Print Date 16.04.2014 000000023457
MSDS_SG