To Simulate, Design & Implementation Of Maximum Power

Harvesting Of Solar Energy By Using DC-DC Converter

Shubham Tapase, Shubham Vairagade Praful Hulkey
Department of Electrical Engineering Department of Electrical Engineering
DMIETR, Wardha DMIETR, Wardha
India India
line 4-e-mail address if desired line 4-e-mail address if desired

Abstract— Day by day non-renewable energy source replenished irradiation varies from morning to evening with changing
in the world may be up coming years this sources will be climatic condition. Because of this limitation it’s necessary to
completely finished. And this sources will not fulfill requirements. use intermediate power processor which gives maximum
Today itself is necessary to move toward renewable energy
desirable output with respective to the change in input.
source. India developed world largest solar power plant has 648
MW capacity in kerla. But problem with renewable sources are
A dc-dc converter act as an intermediate power processor
installation cost is high and efficiency is low. between the load and the PV module Which transfer
Photovoltaic energy is infinite source of renewable energy. Solar maximum power from solar PV panel to the connected load.
energy has main advantages is that clean, maintenance free and MPPT is a technique which track this peak power and convey
space limited area compare to the other type of renewable energy it to load at all time. MPPT in a basically dc-dc converter
which can be space consuming. one of method to improve the whose duty cycle is adjusted for drawing the amount of
efficiency of photovoltaic system by using intermediate power current so that the system operates in maximum power point.
processor which changes the current and voltage levels such that In MPPT commonly used technique is the P&O algorithm.
maximum power can be extracted.
The P&O algorithm perturbs the operating point of the PV
In this project, we analyze the design and simulation of the
electrical operation of a photovoltaic (PV) system. Photovoltaic module by increasing or decreasing a control parameter by a
energy are used as renewable energy system. Photovoltaic (PV) small amount and measuring the PV array output before and
cells are used to generate dc voltages and given to DC-DC after the perturbation. If the power increases, the algorithm
converter. Designing of converter gives constant output. DC-DC continuous to perturb the system in the same direction;
converter used as Buck type of converter. The converter output is otherwise the system is perturbed in the opposite direction.
given to battery. Buck converter gives constant output which will As shown in block diagram, system is consists of a PV
controlled by PWM controller and feedback control system. A panel, controller circuit, buck converter and a battery. It is
maximum power point tracking (MPPT) algorithm technique is equipped with analog to digital converters and PWM
used to track the peak power to maximize the produced energy.
This algorithm will identify the suitable duty cycle ratio in which
controller. A/D converter used to convert signal coming from
buck converter should operate to maximum point. The MPPT current and voltage sensors.
algorithm is important in increasing the efficiency of the system.
Keywords—component; formatting; style; styling; insert (key
words) II. BASIC CHARACTERISTICS OF PV MODULE
I. INTRODUCTION A. Circuit Configuration
As we all know that, Non-Renewable energy source are A solar cell is an electronic device which directly convert
depleting day by day it is necessary to used maximum sunlight into electricity. solar irradiation falls on solar cell
renewable energy as much as possible. The increasing demand produces both current and voltage to generate electric power.
for electricity and decreasing rate of the stored energy is the Figure 1 shows widely used single diode equivalent circuit
main cause for choosing the renewable energy. As non model to represent the characteristics of PV panel for
renewable energy source cause various harmful effect to the analyzing and simulation of PV system. The model represent
atmosphere .But in renewable energy source there is not such photovoltaic panel as a current source I ph in shunt with single
effect on atmosphere renewable energy source are clean, diode and resistor Rsh as well as series resistor Rs.
maintenance-free and also renewable energy are exists in large
quantity in our nature out of all renewable energy source solar
energy are available anywhere in large quantity. But it is
clearly seen that it is necessary to reduce manufacturing cost
and increase the efficiency of solar energy conversion system.
Because of performance of the PV module not desirable. Now
it is main concern to improve the efficiency of this technology.
Although solar charge available throughout the day its
 Figure 1. Equivalent circuit of solar cell

The output current from the Photovoltaic module is

I=I p h -I d (1)
Figure 2. I-V characteristics of PV module
I d =I 0 (e q v d / K T -1) (2)
S ubsti t ut i ng equat i on (2) in (1)
We get ,
I=I p h -I 0 (e q V d / K T -1) (3)
B ut , Vol t age across Di ode (V d )
V d =(V+IR s )/N (4)
S ubsti t ut i ng equat i on (4) in (3)
I=I p h -I 0 (e q ( V + I R s ) / N K T -1) (5)
Wh ere,
I is the Output Voltage of PV module,
Id is the Diode current ,
I0 is the reverse saturation current of cell,
V is the output voltage of the cell,
q stands for electron charge (1.602 ×10-19C),
Figure 3. P-V characteristics of PV module
K is the Boltzman constant.(1.38×10-23 J/K),
C. Analysis of voltage variation with respect to time of PV
N is the no. of diode in series to form single diode module
model And T is the junction temperature in Kelvin.
Table 1.SPECIFICATION OF PV MODULE

SPECIFICATION VALUE
Rated Power 70 W

Open circuit Voltage(Voc) >21V

Short Circuit current(Isc) 3.33A

Maximum Voltage(Vm) 17.5V

Maximum Current(Im) 4A

B. Output characteristics of PV module

The I-V Characteristics of a PV system for different Figure 4.Voltage vs time variation of PV module
irradiances as shown in fig.2&3 from the study we see that
both power and current level increase with increased level of
irradiation at constant temperature on the other hand voltage 4. DC-DC BUCK CONVERTER
remain relatively constant for different Irradiation.
 The dc-dc buck converter converts a higher dc input
voltage to lower dc output voltage. The basic buck converter The solar panel is designed using matlab shown in figure 7
structure is shown figure 5. It consist of controlled switch s, an With 36 solar cell connected in series according to the power
uncontrolled switch diode D, an inductor L, an capacitor C, requirement and its voltage, current and power are measure
and a load resistance R. under various weather condition.

Figure 5. Buck converter circuit

In a buck converter, the duty cycle (D), i.e., the ratio of “ON”
time to Total time period is given as

Figure 7.Simulink model of Solar Panel

Similarly, the buck converter is also designed by using matlab

Where,
in order to transfer maximum power from solar panel to the
Vin and VO are the input and output voltage of the buck
load as shown as
converter.
Equations for the selection of Inductor,

Equations for the selection of Capacitor,

Here, Switching frequency denoted by fs; ΔI L is the inductor

current ripple and ΔVout is output voltage ripple.

5.BLOCK DIAGRAM

Figure 8.Simulink model of Close loop Buck Converter

Table 2. Buck converter specification

Specification Value

Input voltage 17.5 V DC

Output voltage 12 V DC
Switching frequency 50 kHz
Duty cycle 70 %
Inductance 47µH
Capacitance 220 µF
Figure 6. Block diagram of complete PV system
6. SIMULINK MODEL OF COMPLETE SYSTEM
Required output of buck converter as shown in below figure 9
of input 17.5v dc.

Figure 9. output result of close loop buck converter

7. MPPT TECHNIQUE
Maximum power point tracking (MPPT) is the indirect
technique to increase the efficiency of the PV panel. For the
MPPT process, it will work continuously to make the system Figure 10.P&O algorithm
to operate at or around the MPP. There are many methods to
track the MPP. The most common and basic method that can 8.CONCLUSION
be applied to track the maximum power is the perturb and In this paper, an optimized MPPT technique along with buck
observe method (P&O method). converter is designed for solar system .our objective is to
A principle of the P&O method works by adjusting the reduce the settling time of an output power by comparing
duty cycle of the converter, which indirectly perturb the power output voltage with the input voltage. Also this paper provide
output of the PV. Then, the system compares the new power to low cost microcontroller based fast response MPPT technique.
the previous power to determine the next adjustment. Let’s P&O algorithm is used to track maximum power point
define the difference of the PV power output as irrespective of irradiation, temperature and load condition.
dP=P(k)-P(k-1) (1) MPPT algorithm responds in very fast manner and its
 If the value P(k)>P(k-1) is positive, the system will accuracy is higher that it reaches ti steady state very quickly.
adjust voltage(increase or decrease the voltage) by Hence the results obtained at different environmental
adjusting the duty cycle of the converter in the same condition are found to be satisfactory.
direction.
9. REFERENCES
 If the value P(k)<P(k-1) is negative, the system will [1] Thanyanut Lueangamornsiri*, Kittikun Thongpull, Kusumal
Chalermyanont, Warit Wichakool “Design and Development
adjust voltage(increase or decrease the voltage) by
of A Stand-Alone Solar Energy Harvesting System by MPPT
adjusting the duty cycle of the converter in the and Quick Battery Charging,” Transaction ©2016 IEEE
opposite direction.
[2] Rashed Hassan Bipu, Syed Mohammad Sifat Morshed
Chowdhury, Manik Dautta, Md. Zulkar Nain and Shahidul
The diagram of this method is shown in figure 10 the
Islam Khan “Modeling and Analysis of Maximum Power
advantage of the P&O method is a simple method for MPP
Point Tracking Algorithms Using MATLAB/Simulink”, 2nd
determination. The P&O method can also work well at steady IEEE Conf. on Electrical Engineering and Infonnation &
state, when light intensity and temperature change slowly. Communication Technology (ICEEICT) 2015.
[3] Mohammed El Alami, Mohamed Habibi, and Seddik Bri,
“The Modeling of Maximum Power Point Tracking
Controller for Increasing Efficiency of Solar Power
System”, IEEE transactions on 2015.
[4] Kamala J, Tamilarasi A ,“ Characterization Of Pv Cells With
Varying Weather Parameters To Achieve Maximum Power,”
IEEE Sponsored 2nd International Conference On
Electronics And Communication Systems(Icecs ‘2015)
[5] S.R.Osman*, N.A.Rahim and J.Selvaraj, “Microcontroller
Based Solar Battery Charging System with MPPT Features
at Low Irradiance Condition”, CSEE journal of power and
energy systems, vol. 1, no. 4, December 2015.
[6] Rokeya Jahan Mukti, Ariful Islam,, “Designing an Efficient
Photovoltaic System with Maximum Power Point Tracking
Technique by Comparing Different Converter Topologies.”,

17th International Conference on 2014.

[7] Harishankar Suresh , Anand Baskaran, Sudharsan K. P.,
U.Vignesh, Viveknath T., Sivraj P, Vijith K., “Efficient
Charging of Battery and Production of Power from Solar
Energy,” IEEE Trans. on 2014.
[8] Dhananjay Choudhary, Anmol Ratna Saxena, “DC DC buck
converter for MPPT of PV System”, International Journal
of Emerging Technology and Advanced Engineering,
Volume 4, Issue 7, July 2014.
[9] Ashish Pandey, Nivedita Dasgupta, and Ashok Kumar
Mukerjee, “High-Performance Algorithms for Drift
Avoidance and Fast Tracking in Solar MPPT System”, IEEE
Transactions on energy conversion, vol. 23, no. 2, June
2008.