DSG Clutch Removal Tool Set Eng Printer PDF

www.sandblomnewhamm e r.
co m
DSG Clutch tool V.A.G. DQ200 (0AM, 0CW)

Tools
Required tools for changing dual clutch
• DSG Clutch exchange tool kit

• Soft hammer
• Plier for snap rings
Removal and installation of dual clutch
Application
The 7 speed dual clutch gearbox DQ200 (0AM, 0CW) in Audi, Seat, Skoda and Volkswagen
Brief instruction
1. Remove the dual clutch by pulling it out of the gearbox with the tool.
2. Replace old clutch assembly with new parts.
3. Adjust position of the thrust bearings with correct shims.
4. Push the new clutch into correct position with the tool.
5. Check the clearance on both clutches.
6. Install the gearbox in the car.
7. Perform an adaption of the clutch with a diagnosis tool.
w w w.sandblomnewhammer.com
2
Important information
The breathing holes on the gearboxes must be plugged to avoid leakage. If the mechatronic oil leaks
out the complete mechatronic unit must be changed. If the gearbox oil leaks out a complete oil
exchange needs to be performed.
A clutch can only be installed once since removal of the clutch damages the clutch. Once removed
the clutch cannot be reused.
When changing the clutch it is recommended to check the dual mass flywheel. Change it if
nescessary. A clutch must not under any circumstances fall out of place. Any shocks on the clutch
may damage the adaption mechanism.
Plug both the breathing holes with plastic caps
If oil leaks out of mechatronic the complete mechatronic unit needs to be changed.
If oil leaks out of the gearbox all of the oil needs to be removed and then refilled with the correct
volume of oil.
w w w.sandblomnewhammer.com
3
Turn the transmission clutch side up.
Use a support below to keep it steady.
Take out the snap ring.
w w w.sandblomnewhammer.com 4
Take out the hub for K1.
Shock with tool and soft hammer in order to ease up the snap
ring for clutch pack.
Take out snap ring.
Pull out the old clutch pack.
Take out the old forks, thrust bearings and plastic fork seat.
Mount the new fork seat and the small fork (K2) and the K2
thrust bearing without shim.
Mount the tool on the shaft, and mount the snap ring.
Twist apart the tool parties till lightly tightened, and test, which
shim will fit in the slot.
Generation I.
Generation II.
Measure the thickness of the shim, read on the new clutch
pack, how much to add/subtract on the measured schim
thickness, and choose a shim.
Example: measured shim thickness 2,20 mm, reading on clutch pack”K2 +0,20”.
Shim to be used: 2,40 mm
Put aside a small (K2) shim 2,40 mm. Take out the tool and K2 thrust bearing.
Mount the new K1 fork with the K1 thrust bearing WITHOUT shim.
Mount the tool again, and twist as earlier for K2.
Choose a shim to fit in slot, add/subtract as for K2 earlier.
Example: measured shim 3,00 mm, reading on clutch pack ”K1 -0,40. Shim to be used; 2,60 mm.
Put aside a K1 shim of proper thickness. Take out the tool.
Generation I.
Generation II.
Mount the chosen shim for K1. Mount the K2 shim and the K2
thrust bearing.
Picture shows shim Generation I. Picture shows shim Generation I.
Place the new dual clutch pack carefully in Check that the dual clutch pack is correctly
place. It has to be fit into the larger splines (on in place by checking the distance between
the outer input shaft). the upper edge of the outer (hollow) input
shaft and the upper bearing edge. The
distance must be less than 8 mm (normally
approximately 7 mm).
Install the pushing tool and the bar.
Bolt on the bar with washers and 10 mm bolts and nut(s) –
tighten by hand.
Screw on the pushing wheel, and screw it in till the clutch

pack touch the bottom.
Install the snap ring.
Pointed side of snap ring upwards.
Install the dial indicator with bar by attaching the dial indicator holder and then attaching
the dial indicator to the holder. The dial indicator tip shall hit the K2 clutch plate.
Measure the clearance of K2 by lifting the clutch plate with 2 hooks. The clearance must
be 0,3 – 1,0 mm. If out of range, the dual clutch needs to be changed* and reinstalled.
* The dual clutch is damaged when removed. A removed clutch can therefore not be
reinstalled.
Install the dial indicator to measure clearance for K1

(must be 0,3 – 1,0 mm).
Install the K2 hub and snap ring as shown in picture.
Align marking for index in at snap ring stopper.
Turn the transmission and remove the breathing caps before

installing gearbox in the car.
Sandblom New Hammer AB
Varbergsvägen 416
43973 Fjärås
[email protected]
www.sandblomnewhammer.com

DSG Clutch Removal Tool Set Eng Printer PDF

Uploaded by

Copyright:

Available Formats

DSG Clutch Removal Tool Set Eng Printer PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DSG Clutch Removal Tool Set Eng Printer PDF

Uploaded by

Copyright:

Available Formats

www.sandblomnewhamm e r.

DSG Clutch tool V.A.G. DQ200 (0AM, 0CW)

Required tools for changing dual clutch

• DSG Clutch exchange tool kit

Removal and installation of dual clutch

Plug both the breathing holes with plastic caps

Take out the snap ring.

Pull out the old clutch pack.

Picture shows shim Generation I. Picture shows shim Generation I.

Install the pushing tool and the bar.

Screw on the pushing wheel, and screw it in till the clutch

Pointed side of snap ring upwards.

Install the dial indicator to measure clearance for K1

Turn the transmission and remove the breathing caps before

You might also like