Industrial Electric Drives Linear Motion and Service Mobile

Hydraulics and Controls Assembly Technologies Pneumatics Automation Hydraulics

RA 92 711/05.04 1/36
Variable Axial Piston Pump Replaces: 05.95
RA 92 712/05.95
(A)A10VSO

open circuit

Size 18 ... 140

Series 31
Nominal pressure 4000 psi (280 bar)
Peak pressure 5100 psi (350 bar)

Contents Features
Ordering code - standard range 2 – Variable displacement axial piston pump of swashplate
Fluids 4 design for hydrostatic open circuit systems

Technical data 5 – Flow is proportional to drive speed and displacement. It can

be infinitely varied by adjustment of the swashplate.
Noise level 7
Drive power and flow 8 – SAE mounting flange

DG - two point, direct control 10 – Flange connections to SAE

DR - Pressure control 12 – 2 case drain ports
DRG - Pressure control, remote 14 – Good suction characteristics
DFR / DFR1 - Pressure flow control 16 – Permissible continous pressure 4000 psi (280 bar)
DFLR - Pressure / flow / power control 18
– Low noise level
Unit dimensions, Size 18 20
– Long service life
Unit dimensions, Size 28 21
– Axial and radial load of drive shaft possible
Unit dimensions, Size 45 22
Unit dimensions, Size 71 23 – High power-weight ratio

Unit dimensions, Size 100 24 – Wide range of controls

Unit dimensions, Size 140 25 – Short response times
Through drives 26 – Through drive option for multi-circuit system
Overview of through drive mounting options 27
Dimensions of through drives 29
Installation notes 34
Safety information 35
2/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Ordering code - standard range

Hydraulic Fluid, Type of rotary group 18...45 71...140

Mineral oil and HFD (no code) ● ●
HFA, HFB and HFC - Fluids ● ● E
High-Speed-Version - ● H

Axial Piston Unit

Swashplate design, variable size 18 A10VS
size 28 to 140 AA10VS

Type of operation
Pump in open circuit O

Size 18 28 45 71 100 140

in3/rev. 1.10 1.71 2.75 4.33 6.10 8.54
Displacement Vg max
cm3/rev. 18 28 45 71 100 140

Control device 18 28 45 71 100 140

Two-position control, direct controls DG ● ● ● ● ● ● DG
Pressure control DR ● ● ● ● ● ● DR
DR G ● ● ● ● ● ● DRG
remote control
Pressure flow control DFR ● ● ● ● ● ● DFR
DFR 1 ● ● ● ● ● ● DFR1
without orifice between X and tank
Pressure, flow and power control - ● ● ● ● ● DFLR
Pressure and flow control, electronic, see RA30022 ● ● ● ● ● ● DFE1
Electro-hydraulic pressure control, see RE92707 ● ● ● ● ● ● ED

Series
31

Direction of rotation
Viewed on shaft end clockwise R
counter clockwise L

Seals
NBR nitril-caoutchouc, shaft seal in FKM P
FKM flour-caoutchouc V

Shaft end 18 28 45 71 100 140

SAE Parallel with key ● ● ● ● ● ● K
SAE Splined shaft ● ● ● ● ● ● S
SAE Splined shaft (higher through drive torque) ● ● ● ● - - R
SAE Splined shaft (not suitable for through drive) ● - ● - ● - U

Mounting flange 18 28 45 71 100 140

SAE 2-bolt ● ● ● ● ● - C
SAE 4-bolt - - - - - ● D

● = available
❍ = in preparation
- = not available
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 3/36

AA10VS O / 31 -

Hyraulic Fluid, Type of rotary group

Axial Piston Unit
Type of operation
Size
Control device
Series
Direction of rotation
Seals
Shaft end
Mounting flange

Service line connections 18 28 45 71 100 140

Pressure port B and suction port S: SAE ports at opposite sides ● ● ● - ● ● 62
UNC fixing threads - - - ● - - 92

Through drives 18 28 45 71 100 140

without through drive ● ● ● ● ● ● N00
with through drive to accept an axial piston pump or a gear pump
Mounting flange SAEJ744 hub sealing
82-2(A) keyed (A-B) axial ❍ ● ● ● ● ● K401)
101-2 (B) keyed (B) axial - ● ● ● ● ● K031)
101-2 (B-B) keyed (B-B) axial - - ● ● ● ● K051)
127-2 (C) keyed (C) axial - - - ● ● ● K081)
127-2 (C) keyed (C) radial - - - - ● ● K381)
152-4 (D) keyed (D) axial - - - - - ● K211)
82-2 (A) 5/8 in (A) axial ● ● ● ● ● ● K01
82-2 (A) 3/4 in (A-B) axial ● ● ● ● ● ● K52
101-2 (B) 7/8 in (B) axial - ● ● ● ● ● K68
101-2 (B) 1 in (B-B) axial - - ● ● ● ● K04
127-2 (C) 1 1/4 in (C) axial - - - ● ● ● K07
127-2 (C) 1 1/2 in (C-C) axial - - - - ● ● K24
152-4 (D) 1 3/4 in (D) axial - - - - - ● K17

1)
Not for new projects. Permitted with reduced through drive torque only (see page 26).
4/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Fluids
We request, that before starting a project, detailed information Notes on the selection of hydraulic fluid
about the choice of hydraulic fluids and application conditions
In order to select the correct fluid, it is necessary to know the
are taken from our catalog sheets RE 90220 (petroleum oil)
operating temperature in the tank (open circuit) in relation to
and RE 90221 (environmentally acceptable hydraulic fluids).
the ambient temperature.
When using environmentally acceptable hydraulic fluids
The hydraulic fluid should be selected so that within the
possible limitations for the technical data apply. If necessary
operating temperature range, the viscosity is within the op-
please contact our technical department (please indicate type
timum range (νopt.; see shaded section of the selection dia-
of the hydraulic fluid used in your application when ordering.
gram). We recommend that the higher viscosity grade is
Operating viscosity range selected in each case.
We recommend that the operating viscosity (at operating Example: at an ambient temperature of X °F (°C) the operating
temperature) for both the efficiency and life of the unit, be temperature in the tank is 140 °F (60 °C). In the optimum vis-
chosen within the optimum range of cosity range νopt ( shaded area), this corresponds to viscosity
grades VG 46 or VG 68, VG 68 should be selected.
νopt = opt. operating viscosity 80...170 SUS (16...36 mm2/s) Important: The leakage oil temperature is influenced by
pressure and speed and is typically higher than the tank
temperature. However max. temperature at any point in the
referred to tank temperature at open circuit.
system may not exceed 195 °F (90 °C).
Viscosity limits At high temperatures please use FKM seals.
The limiting values for viscosity are as follows:
If the above mentioned conditions cannot be kept due to ex-
νmin = 60 SUS (10 mm2/s) treme operating parameters or high ambient temperatures,
short term (t ≤ 1 min) please consult us.
at a max. permissible leakage oil temperature
Filtration of fluid
of tmax = 195 °F (90 °C).
The finer the filtration, the better the achieved cleanliness of
Please note that the max. fluid temperature of 195 °F (90 °C) is
the fluid and the longer the life of the axial piston unit.
also not exceeded in certain areas (for instance bearing area).
The temperature in the bearing area is approx. 7 °F (5 K ) To ensure a reliable functioning of the axial piston unit, a mini-
higher than the average leakage fluid temperature. mum cleanliness of
νmax = 7500 SUS (1600 mm2/s) 20/18/15 acc. to ISO 44061) is necessary.
short term (t ≤ 1min)
If the above cleanliness classes cannot be met please consult
on cold start
us.
(p ≤ 435 psi/30 bar, n ≤ 1000 rpm, tmin = -13 °F/-25 °C)
1)
draft issue 1999

Selection diagram
(5000) 1000 1000 (4635)
(3000) 600
(2000) 400
Viscosity v mm2/s (SUS)

VG 68
VG

VG 32
VG 46
VG 2

(1000) 200
10
2

(500) 100

(300) 60
(200) 40 36
(150) (170)
vopt.
(100) 20
(80) 16
(80)
(70)
(60) 10
194
-13 0 20 40 60 80 100 120 140 160 180

(-20) (-10) (0) (10) (20) (30) (40) (50) (60) (70) (80) (90)
(-25)
Temperature t in °F (°C)
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 5/36

Technical data
Inlet operating pressure range Maximum permissible speed (Speed limit)
Absolute pressure at port S Graph, showing permissible speed with increased inlet pres-
sure at port S ( pwabs ) resp. reduced displacement(Vg < Vg max ).
pabs min _____________________________________________________________ 12 psi (0,8 bar)
1,2 bar psi
pabs max __________________________________________________________ 435 psi (30 bar)
1,6 23

Input pressure p abs

Output operating pressure range

Speed n/nmax
Pressure at port B 1,4 20
1,1
Nominal pressure pN _________________________________ 4000 psi (280 bar)
1,2 17.5
Peak pressure pmax ____________________________________ 5100 psi (350 bar)
(Pressure data to DIN 24312)
Applications with intermittet operating pressure up to 4600 psi 1,0 1,0 14.5
(315 bar) at < 10 % duty are permissible.
0,9 13
Limitation of pump output pressure spikes is possible with relief
valve blocks mounted directly on flange connection, acc. to
data sheets RA 25 880 and RE 25 890 to be ordered 0,9 0,8 11.5
separately. 0,7 0,8 0,9 1,0

Direction of flow Displacement Vg / Vgmax

S to B. High speed version

Case drain pressure The size 71...140 is available in an optional high speed version.
The max. permissible pressure of the leakage fluid (at port L, L1) This version allows higher drive speeds at max. displacement
max. 7 psi (0,5 bar) higher than inlet pressure at port S, but not (higher output flow) without affecting outside dimensions, see
higher than 29 psi (2 bar) absolute. table on page 6.

pL abs max _____________________________________________________________ 29 psi (2 bar) Important: The drive speed increase (1.2 • n0) refers to the
standard drive speed n0.
e.g. size 100: nmax = 1.2 • 2000 rpm = 2400 rpm
WRONG: 1.2 • 2400 rpm = 2880 rpm

Mechanical displacement limiter

Mechanical displacement limiter is standard on the non-
through drive model N00, but not possible for the model with
through drive.
Exception: With DFE1 control a max. displacement screw is
not possible at all.
Vg max: for sizes 18 to 140
Setting range from 50 % to Vg max stepless
Vg min: for sizes 100 to 140
Setting range from zero to 50 % of Vg max stepless
6/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Technical Data
Table of values
Size (A)A10VSO Standard 18 28 45 71 100 140
AA10VSO High Speed 71 100 140
Displacement Vg max in3 1.10 1.71 2.75 4.33 6.1 8.54 4.33 6.1 8.54
(cm3) (18) (28) (45) (71) (100) (140) (71) (100) (140)
Speed1), max.
at Vg max n0 max rpm 3300 3000 2600 2200 2000 1800 2550 2300 2050
at increased inlet pressure n0 max perm. rpm 3900 3600 3100 2600 2400 2100 2600 2400 2100
pabs resp. Vg < Vgmax
Flow, max
at n0 max qvo max gpm 15.7 22 31 41 53 67 48 61 76
(L/min) (59.4) (84) (117) (156) (200) (252) (181) (230) (287)

at nE = 1800 rpm qvo gpm 7.2 13.3 21.4 33.8 47.6 67 33.8 47.6 67
(L/min) (32) (59) (81) (128) (180) (252) (128) (180) (252)
Power, max. (∆p = 4000 psi (280 bar))
at n0 max Po max HP 36.6 51 72 96 124 156 112 142 177
(kW) (28) (39) (55) (73) (93) (118) (84) (107) (134)
at nE = 1800 rpm P HP 19 31 50 79 111 156 79 111 156
(kW) (15) (24) (38) (69) (84) (118) (69) (84) (118)
Torque, max.
at Vg max Tmax ft-lb 58 91 146 230 324 453 230 324 453
(∆p=4000psi (280bar)) (Nm) (80) (125) (200) (316) (445) (623) (316) (445) (623)
at Vg max T ft-lb 14.6 33 53 83 117 164 83 117 164
(∆p=1450psi (100bar)) (Nm) (28.6) (45) (72) (113) (159) (223) (113) (159) (223)
Moment of inertia J lbs-ft2 0.022 0.0403 0.0783 0.1970 0.3963 0.5743 0.1970 0.3963 0.5743
(about drive axis) (kgm2) (0.00093) (0.0017) (0.0033) (0.0083) (0.0167) (0.0242) (0.0083) (0.0167) (0.0242)
Fill volume gal. (L) 0.1 (0.4) 0.2 (0.7) 0.26 (1.0) 0.4 (1.6) 0.6 (2.2) 0.8 (3.0) 0.4 (1.6) 0.6 (2.2) 0.8 (3.0)
Weight (without fluid) ca. m lbs (kg) 26.5 (12) 33 (15) 46 (21) 73 (33) 99 (45) 132 (60) 73 (33) 99 (45) 132 (60)
Permissible loading of drive shaft

max. perm. load Fq Fax max lbf (N) 157 225 337 540 900 1080 540 900 1080
± Fax
(700) (1000) (1500) (2400) (4000) (4800) (2400) (4000) (4800)
X/2 X/2
max. perm. load2) X
Fq max lbf (N) 79 270 337 427 517 630 427 517 630
(350) (1200) (1500) (1900) (2300) (2800) (1900) (2300) (2800)
1) These values are valid for an absolute pressure of 14.5 psi (1 bar) at the suction port S. By reducing the displacement or
increasing the input pressure the speed can be increased as shown in the diagram.
2) Please consult us for higher radial forces.

Determination of size

Flow qv =
Vg • n • ηv
231
[gpm]
( qv =
Vg • n • ηv
1000
[L/min]
) Vg = Displacement per revolution in in3 (cm3)
∆ p = Differential pressure in psi (bar)
n = Speed in rpm (min–1)
Torque T =
Vg • ∆ p
24 • π • ηmh
[lb-ft]
( T=
Vg • ∆ p
20 • π • ηmh
[Nm]
) ηv = Volumetric efficiency
ηmh = Mechanical-hydraulic efficiency
ηt = Total efficiency
Power P=
qv • ∆ p
1714 • ηt
[HP]
( P=
qv • ∆ p
600 • ηt
[kW]
)
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 7/36

Noise level
Characteristics for pump
Measured in an anechoic chamber
Distance from microphone to pump = 3.3 ft (1 m)
Measuring error: + 2 dB(A)
Fluid: Hydraulic oil to ISO VG 46 DIN 51519, t = 122 °F (50 °C)

Size 18 Size 71
74 80 qv max
qv max
72 78 qv zero
qv zero 76

noise level LA [dB (A)]

noise level LA [dB (A)]

70 qv max
74 n = 2200 rpm
68 n = 3000 rpm qv zero
qv max 72 n = 1800 rpm
66
qv zero 70
64 n = 1500 rpm
68
62 66

60 64

58 62
60
56
500 1000 1500 2000 2500 3000 3500 4000 psi 58
500 1000 1500 2000 2500 3000 3500 4000 psi
0 (50) (100) (150) (200) (250)(280)(bar) 0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p operating pressure p
Size 28 Size 100
74 82 qv max
qv max
72 80
qv zero qv zero
noise level LA [dB (A)]

78
70 qv max qv max
n = 2000 rpm
noise level LA [dB (A)]

n = 3000 rpm n = 1800 rpm qv zero 76

68 n = 1800 rpm qv zer o
74
66 72
64 70
62 68
66
60
64
58
62
56
500 1000 1500 2000 2500 3000 3500 4000 psi 60
500 1000 1500 2000 2500 3000 3500 4000 psi
0 (50) (100) (150) (200) (250)(280)(bar) 0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p operating pressure p
Size 45 Size
84
140
76 qv max qv max
82
74 qv zero qv zero
noise level LA [dB (A)]

qv max 80
noise level LA [dB (A)]

72 78
n = 2600 rpm n = 1800 rpm qv zero n = 1800 rpm
70 76
68 74
72
66
70
64 68
62 66

60 64
62
58
500 1000 1500 2000 2500 3000 3500 4000 psi 60
500 1000 1500 2000 2500 3000 3500 4000 psi
0 (50) (100) (150) (200) (250)(280)(bar) 0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p operating pressure p
8/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Drive power and flow

Fluid: Hydraulic oil to ISO VG 46 DIN 51519, t = 122 °F (50 °C)

Size 18
(L/min) gpm (kW) HP
n = 1500 rpm
(80) 20 (40)
n = 3300 rpm
(60) (30) 40

Flow qv

drive power P
qv Pqv max
(40) 10 (20)
20
(20) Pqv zero (10)

0 500 1000 1500 2000 2500 3000 3500 4000psi 0

0 (50) (100) (150) (200) (250) (280)(bar)
operating pressure p

Size 28 (L/min) gpm (kW) HP

60
(80) 20 (40)
n = 1800 rpm qv
(60) Pqv max (30) 40
Flow qv

drive power P
n = 2000 rpm
(40) 10 (20)
20
(20) Pqv zero (10)

0 500 1000 1500 2000 2500 3000 3500 4000psi 0

0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p

Size 45 (L/min) gpm (kW) HP

(120) (60) 80
30
n = 1800 rpm (100)
qv
(50)
60
Flow qv

drive power P
n = 2000 rpm (80) (40)
20
(60) (30) 40
Pqv max
(40) 10 (20)
Pqv zero 20
(20) (10)

0 500 1000 1500 2000 2500 3000 3500 4000 psi 0

0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p

Size 71 (L/min) gpm (kW) HP

(160) (80)
40 100
n = 1800 rpm (140) qv (70)
Flow qv

drive power P

n = 2000 rpm (120) 30 (60) 80

(100) (50)
60
(80) 20 Pqv max (40)
(60) (30) 40
(40) 10 Pqv zero
(20)
20
(20) (10)

0 500 1000 1500 2000 2500 3000 3500 4000 psi 0

0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 9/36

Drive power and flow

Fluid: Hydraulic oil to ISO VG 46 DIN 51519, t = 122 °F (50 °C)

Size 100 (L/min) gpm (kW) HP

(200) (100)
n = 1800 rpm 50
(180) (90) 120
n = 2000 rpm

Flow qv

drive power P
(160) qv (80)
40 100
(140) (70)
(120) Pqv max (60) 80
30
(100) (50)
60
(80) 20 (40)
(60) (30) 40
(40) 10 Pqv zero (20)
20
(20) (10)

0 500 1000 1500 2000 2500 3000 3500 4000 psi 0

0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p

Size 140 (L/min) gpm (kW) HP

(260) (130)
n = 1800 rpm
(240) qv (120) 160
Flow qv

drive power P
60
(220) (110)
140
(200) (100)
50
(180) (90) 120
(160) (80)
40 100
(140) Pqv max (70)
(120) (60) 80
30
(100) (50)
60
(80) 20 (40)
(60) (30) 40
(40) 10 (20)
Pqv zero 20
(20) (10)

0 500 1000 1500 2000 2500 3000 3500 4000 psi 0

0 (50) (100) (150) (200) (250)(280)(bar)
operating pressure p
Overall efficiency
qv • p qv • p
ηt =
Pqv max • 1714 (P qv max
• 600 )
Volumetric efficiency
q
ηv = q v
v theor.
 10/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

DG - two point, direct control

The pump can be set to a minimum swivel angle by connecting Circuit drawing
an external switching pressure to port X. X
This will supply the control pistion directly with control oil; a
minimum pressure of pst ≥ 725 psi (50 bar) is required.
The pump can only be switched between Vg max or Vg min. B

Please note, that the required switching pressure at port X is

directly dependent on the actual operating pressure pB in
port B. (See switching pressure diagramm)
Control pressure pst in X = 0 psi (0 bar) Vg max
Control pressure pst in X ≥ 729 psi (50 bar) Vg min
The max. premissible switching pressure pst is 4000 psi
(280 bar).
S L1 L
with size 100 and 140 only
Switching pressure diagram
psi (bar)
Ports
1749 (120) B Pressure port
1457 (100) S Inlet port
req. switching pressure pst

L,L1 Case drain port (L1 plugged)

729 (50) X Control port (plugged)

0 729 1020 2040 3060 4000 psi

(50) (70) (140) (210) (280) (bar)
operating pressure pB
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 11/36

Before finalising your design, please

Unit dimensions DG request a certified installation drawing.
Dimensions in inches (mm).
Size 18 ... 100

port for port for

counter-clockwise rotation clockwise rotation

Size 140

port for port for

counter-clockwise rotation clockwise rotation

Size A1 A2 A3 A4 X (plugged)
18 5.83 (148) 3.52 (89.5) 3.68 (93,5) 0.12 (3) R 1/4 in
28 6.22 (158) 3.94 (100) 4.07 (103,5) 0.12 (3) R 1/4 in
45 6.81 (173) 4.33 (110) 4.47 (113,5) 0.12 (3) R 1/4 in
71 7.91 (201) 4.86 (123,5) 5.02 (127,5) 0.12 (3) R 1/4 in
100 10.55 (268) 5.06 (128,5) 5.22 (132,5) 0.12 (3) R 1/4 in
140 10.55 (268) 6.02 (153) 6.22 (158) 0.18 (4) R 1/4 in
12/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

DR - Pressure control
The pressure controller serves to maintain a constant pressure Circuit drawing
in a hydraulic system within the range of the pump. The pump Size 18 ... 100
therefore supplies only the amount of hydraulic fluid required
by the system. Pressure may be steplessly set at the pilot valve.
B
Static characteristic
(at n1 = 1500 rpm; toil = 122°F / 50°C)

hysteresis and pressure rise ∆pmax 58 psi (4bar)

qv max
Flow qv

with size 100 only S L1 L

Circuit drawing
Size 140
setting range

qv min
290 psi 4000 psi
(20 bar) operating pressure p (280 bar)

Dynamic characteristic
The opening curves are mean values measured under test
conditions with the unit mounted inside the tank.
Conditions: n = 1500 rpm
toil = 122°F (50°C)
Main relief set at 5100 psi (350 bar)
Ports
B Pressure port
Stepped loading by suddenly opening or closing the pressure
S Inlet port
line using a pressure relief valve at 3.3 ft (1 m) downstream
from the pump pressure outlet. L,L1 Case drain port (L1 plugged)
psi (bar)
5100 (350)
Controller data
4350 (300) Hysteresis and repetitive accuracy ∆p ____ max. 45 psi (3 bar)

3600 (250) Pilot oil consumption max. approx 0.8 gpm (3 L/min)
operating pressure p

Flow loss at qvmax see pages 8 and 9.

2900 (200)
Control times
2200 (150)
tSA [ms] tSA [ms] tSE [ms]
1450 (100)
Size against 725 psi against 3200 psi zero stroke 4000 psi
725 (50) (50 bar) (220 bar) (280 bar)

0 18 50 25 20
Vgmax 28 60 30 20
45 80 40 20
71 100 50 25
100 125 90 30
(swivel angle)
displacement

140 130 110 30

Vgmin

stroking time tSA destroking time tSE

RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 13/36

Before finalising your design, please

Unit dimensions DR request a certified installation drawing.
Dimensions in inches (mm).
Size 18 ... 100

control valve installed here control valve installed here

for counter-clockwise for clockwise rotation
rotation
adjustment srew for
presssure cut off

On sizes 18 to 100 the DFR valve is used. The flow control spool is blocked and not tested.

Size 140

control valve installed here control valve installed here

for counter-clockwise for clockwise rotation
rotation
adjustment srew for
presssure cut off

Size A1 A2
18 4.13 (105) 4.96 (126)
28 4.17 (106) 5.35 (136)
45 4.17 (106) 5.75 (146)
71 4.17 (106) 6.30 (160)
100 4.17 (106) 6.50 (165)
140 5.00 (127) 6.65 (169)
14/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

DRG - Pressure control, remote

Function and design same as DR. Circuit drawing not included in scope of supply
Size 18 ... 100
A pressure relief valve may be externally piped to port X for
remote control purposes. However it is not included in the
scope of supply with the DRG control.
The differential presssure at the DRG control spool is set as
standard to 20 bar and this results in a pilot flow of 0.4 gpm
(1,5 L/min). If another setting is required, please state this in
clear text.
We recommend that one of the following is used as the
seperate pressure relief valve.
DBDH 6 /hydraulic) to RA 25402 or DBETR-SO 381 with
orifice DIA 0.03 in (0,8 mm) in P (electric) to RA 29166.
Max, length of piping should not exceed 6.5 ft (2 m).

with size 100 only

Static characteristic
Circuit drawing not included in scope of supply
(at n1 = 1500 rpm; toil = 122°F / 50°C) Size 140
hysteresis and pressure rise ∆pmax 58 psi (4bar)

qv max
Flow qv

setting range

qv min
290 psi 4000 psi
(20 bar) operating pressure p (280 bar)

Control data Ports

Hysteresis ∆p ________________________ max. 45 psi (3 bar) B Pressure port
S Inlet port
Pilot oil requirement _________ approx. 1.2 gpm (4,5 L/min)
L,L1 Case drain port (L1 plugged)
Flow loss at qvmax see pages 8 and 9.
X Pilot pressure port
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 15/36

Before finalising your design, please

Unit dimensions DRG request a certified installation drawing.
Dimensions in inches (mm).
Size 18 ... 100
control valve installed here control valve installed here
for counter-clockwise for clockwise rotation
rotation
setting srew for setting srew for
max. presssure cut off differential presssure

Size 140

control valve installed here control valve installed here

for counter-clockwise for clockwise rotation
rotation
setting srew for
differential presssure

adapter

Size A1 A2 A3 A4 A5 Port X
18 4.11 (104,5) 4.94 (125) 4.29 (109) 1.57 (40) 5.12 (130) 7/16-20 UNF-2B; 0.45 (11,5) deep
28 4.17 (106) 5.35 (136) 4.69 (119) 1.57 (40) 5.43 (138) 7/16-20 UNF-2B; 0.45 (11,5) deep
45 4.17 (106) 5.75 (146) 5.08 (129) 1.57 (40) 6.02 (153) 7/16-20 UNF-2B; 0.45 (11,5) deep
71 4.17 (106) 6.30 (160) 5.63 (143) 1.57 (40) 7.13 (181) 7/16-20 UNF-2B; 0.45 (11,5) deep
100 4.17 (106) 6.50 (165) 5.83 (148) 1.57 (40) 9.76 (248) 7/16-20 UNF-2B; 0.45 (11,5) deep
140 5.00 (127) 6.65 (169) 5.63 (143) 1.06 (27) 8.74 (222) 9/16-18 UNF-2B; 0.51 (13) deep
16/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

DFR / DFR1 - Pressure flow control

In addition to the pressure control function, the pump flow to Circuit drawing
the actuator may be varied by means of a differential pressure Size 18 ... 100
(e.g. over an orifice or directional control valve). The pump not included
supplies only the amount of fluid as required by the actuator. in scope of
supply
In the DFR1-valve version the orifice between the X port and
with DFR1
tank is plugged.
plugged
For function and content of pressure control see pages 12.
Static characteristic

∆qv (see table)

(at n1 = 1500 rpm; toil = 122°F / 50°C)
qv max
Flow qv

with size 100 only

Circuit drawing
setting range
Size 140
not included
in scope of
qv min supply
290 psi 4000 psi with DFR1
(20 bar) operating pressure p (280 bar) plugged
∆qv (see table)

Static characteristic at variable speed

Flow qv

Ports
speed n B Pressure port
Dynamic characteristic operating curve S Inlet port
psi (bar) L,L1 Drain port (L1 closed)
100 5100 (350)
X Pilot pressure port
4350 (300)
4000 (280) Differential pressure ∆p:
75
3600 (250)
Standard setting: 200 psi (14 bar). If a different setting is
displacement Vg %

load pressure

2900 (200) required please state in clear text.

50
2200 (150) When port X is loaded to tank (and outlet B is closed), a zero
1450 (100) stroke pressure (standby) of p = 260+30 psi (18+2 bar)
25
results. (depends on ∆p)
725 (50)
260 (18)
0 (stand by) Control data
For technical data of pressure control see page 12.
stroking time tSA destroking time tSE Max. flow deviation (hysteresis and rise) measured at drive
speed n = 1500 rpm.
tSA [ms] tSE [ms] tSE [ms]
Size 18 28 45 71 100 140
Size 4000 psi 4000 psi 725 psi
(280 bar)-stand by (280 bar)-stand by (50 bar)-stand by ∆qvmax
18 40 15 40 gpm 0.24 0.26 0.48 0.75 1.06 1.60
28 40 20 40 (L/min) (0,9) (1,0) (1,8) (2,8) (4,0) (6,0)
45 50 25 50 DFR pilot oil consumption ___ max. approx. 0.8 ... 1.2 gpm (3
... 4,5 L/min)
71 60 30 60
DFR1 pilot oil consumption ___ max. approx. 0.8 gpm (3 L/min)
100 120 60 120
Flow loss at qvmax see pages 8 and 9.
140 130 60 130
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 17/36

Before finalising your design, please

Unit dimensions DFR request a certified installation drawing.
Dimensions in inches (mm).
Size 18 ... 100

position of valve for position of valve for

counter-clockwise rotation clockwise rotation
setting srew for
setting srew for flow control
presssure control differential presssure

Size 140

position of valve for position of valve for

counter-clockwise rotation clockwise rotation

setting srew for flow control /

differential presssure
setting srew for
presssure control

adapter

Size A1 A2 A3 A4 A5 Port X
18 4.13 (105) 4.96 (126) 4.29 (109) 1.57 (40) 4.29 (109) 7/16-20 UNF-2B; 0.45 (11,5) deep
28 4.17 (106) 5.35 (136) 4.69 (119) 1.57 (40) 5.43 (138) 7/16-20 UNF-2B; 0.45 (11,5) deep
45 4.17 (106) 5.75 (146) 5.08 (129) 1.57 (40) 6.02 (153) 7/16-20 UNF-2B; 0.45 (11,5) deep
71 4.17 (106) 6.30 (160) 5.63 (143) 1.57 (40) 7.13 (181) 7/16-20 UNF-2B; 0.45 (11,5) deep
100 4.17 (106) 6.50 (165) 5.83 (148) 1.57 (40) 9.76 (248) 7/16-20 UNF-2B; 0.45 (11,5) deep
140 5.00 (127) 8.23 (209) 7.20 (183) 1.06 (27) 8.74 (222) 9/16-18 UNF-2B; 0.51 (13) deep
18/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

DFLR - Pressure / flow / power control

In order to achieve a constant drive torque with a varying Circuit drawing
operating pressure, the swivel angle and with it the output flow Size 28 ... 100
not included
from the axial piston unit is varied so that the product of flow
in scope of
and pressure remains constant. supply
Flow control is possible below the limit of the power curve.

Static characteristic Maximum

power curve

100
Flow qv [%]

75

with size 100 only

Circuit drawing
50 Size 140
not included
Minimum in scope of
supply
power curve
25

0 725 1450 2200 2900 3600 40004350psi

(50) (100) (150) (200) (250) (280)(300)(bar)
operating pressure p

The power characteristic is set at the factory, please state your

requirements in clear text e.g. 27 HP (20 kW) at 1800 rpm.

Control data Ports

For technical data constant pressure control see page 12. B Pressure port
For technical data flow control see page 16. S Inlet port
Start of control _______________ from 1160 psi (80bar) L,L1 Case drain port (L1 closed)
Pilot oil consumption ___ max. approx. 1.45 gpm (5,5 L/min) X Pilot pressure port
Flow loss at qvmax see pages 8 and 9.
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 19/36

Before finalising your design, please

Unit dimensions DFLR request a certified installation drawing.
Dimensions in inches (mm).
Size 28 ... 100
position of valve for position of valve for
counter-clockwise rotation clockwise rotation

power valve

Size 140

position of valve for position of valve for

counter-clockwise rotation clockwise rotation

power valve

Size A1 A2 A3 A4 A5 A6 Port X
28 4.17 (106) 5.35 (136) 4.69 (119) 1.57 (40) 7.60 (193) 4.21 (107) 7/16-20 UNF-2B; 0.39 (10) deep
45 4.17 (106) 5.75 (146) 5.08 (129) 1.57 (40) 8.23 (209) 4.41 (112) 7/16-20 UNF-2B; 0.39 (10) deep
71 4.17 (106) 6.30 (160) 5.63 (143) 1.57 (40) 9.37 (238) 4.88 (124) 7/16-20 UNF-2B; 0.39 (10) deep
100 4.17 (106) 6.50 (165) 5.83 (148) 1.57 (40) 11.93 (303) 5.08 (129) 7/16-20 UNF-2B; 0.39 (10) deep
140 5.00 (127) 8.23 (209) 7.20 (183) 2.22 (56,4) 12.36 (314) 5.51 (140) 9/16-18 UNF-2B; 0.51 (13) deep
20/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Unit dimensions, Size 18 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 18 XXXX/31X-XXX62N00
View W

1.87 (47.6)
3.27 (83)

0.79 (20)
0.25 (6.3) V
B

1)
Flange SAE J744 L

(1
43
82-2 (A)
DIA 3.2479(Ø82.55)h8

2.48 (63)

0.

7)
0.87 (22.2)

(6
64
3.2500

2.
2.48 (63)

2.60 (66)
2.52 (64)
View V

2.06 (52.4)
0.98 (25)
0.45 (11.5) L1
4.19 (106.4)
1.69 (43)
5.98 (152) S
5.71 (145)
7.68 (195) mech.
displacement
W limiter 1.03 (26.2)

Shaft ends
K Parallel with key R Splined shaft 3/4 in 11T S Splined shaft 3/4 in 11T U Splined shaft 5/8 in 9T
ISO 3019-1 19-1 16/32 DP1) 16/32 DP1) 16/32 DP1)
SAE J744-19-4 (A-B) SAE J744-19-4 (A-B) SAE J744-16-4 (A)
0.1884
0.1874
(4.76+0.025 )
1/4-20UNC-2B
0.83 (21.1)

Centering3)
R3.15x6.7 DIN332
3/4 in

Ø 3/4 in
DIA 0.7500 (Ø19.05–0.02)

Centering3)
R3.15x6.7 DIN332
1.13 (28.6) 0.55
0.87 (22)
0.10 (2.5) (14)
1.18 (30)
0.7492

0.62 (15.8)
1.50 (38) 1.50 (38) 0.94 (23.8)
1.25 (31.8)
1.30 (33) usable spline length
1.61 (41)

Ports Tightening torques, max.2)

B Pressure port (standard pressure range) SAE J518 3/4 in
Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.79 (20) deep 29 lb-ft (40 Nm)
S Inlet port (standard pressure range) SAE J518 1 in
Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.79 (20) deep 29 lb-ft (40 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 9/16-18 UNF-2B 59 lb-ft (80 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
3)
Axial locking of the coupling e.g. via clamping coupling or radial mounted binding screw
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 21/36

Before finalising your design, please

Unit dimensions, Size 28 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 28 XXXX/31X-XXX62N00
View W

Flange SAE J744

101-2 (B)

View V

mech.
displacement
limiter

Shaft ends
K Parallel with key R Splined shaft 7/8 in 13T 16/32 DP1) S Splined shaft 7/8 in 13T 16/32 DP1)
ISO 3019-1 22-1 SAE J744-22-4 (B) SAE J744-22-4 (B)

usable spline length

Ports Tightening torques, max.2)

B Pressure port (standard pressure range) SAE J518 3/4 in
Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.71 (18) deep 29 lb-ft (40 Nm)
S Inlet port (standard pressure range) SAE J518 1 1/4 in
Threading in bolt holes ISO 68 7/16-14 UNC-2B; 0.94 (24) deep 48 lb-ft (65 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 3/4-16 UNF-2B 118 lb-ft (160 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
22/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Unit dimensions, Size 45 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 45 XXXX/31X-XXX62N00
View W

Flange SAE J744

101-2 (B)

View V

mech. displacement
limiter

Shaft ends
K Parallel with key R Splined shaft 1 in 15T 16/32 DP1) S Splined shaft 1 in 15T 16/32 DP1) U Splined shaft 7/8 in
ISO 3019-1 25-1 SAE J744-25-4 (B-B) SAE J744-25-4 (B-B) 13T 16/32 DP1)
SAE J744-22-4 (B)
in

9,

usable spline length

Ports Tightening torques, max.2)

B Pressure port (standard pressure range) SAE J518 1 in
Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.71 (18) deep 29 lb-ft (40 Nm)
S Inlet port (standard pressure range) SAE J518 1 1/2 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.87 (22) deep 66 lb-ft (90 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 177 lb-ft (240 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 23/36

Before finalising your design, please

Unit dimensions, Size 71 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 71 XXXX/31X-XXX92N00
View W

Flange SAE J744

127-2 (C)

View V

mech. displacement
limiter

Shaft ends
K Parallel with key R Splined shaft 1 1/4 in 14T 12/24 DP1) S Splined shaft 1 1/4 in 14T 12/24 DP1)
ISO 3019-1 32-1 SAE J744-32-4 (C) SAE J744-32-4 (C)
in

usable spline length

Ports Tightening torques, max.2)

B Pressure port (standard pressure range) SAE J518 1 in
Threading in bolt holes ISO 68 3/8-16 UNC-2B; 0.71 (18) deep 29 lb-ft (40 Nm)
S Inlet port (standard pressure range) SAE J518 2 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.87 (22) deep 66 lb-ft (90 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 177 lb-ft (240 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
24/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Unit dimensions, Size 100 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 100 XXXX/31X-XXX62N00
mech.
View W
displacement
limiter max.

mech.
displacement
limiter min.

mech.
Flange SAE J744 displacement
View V
127-2 (C) limiter min.
mech. displacement
limiter

mech.
displacement
limiter max.

Shaft ends
K Parallel with key S Splined shaft 1 1/2 in 17T 12/24 DP1) U Splined shaft 1 1/4 in 14T 12/24 DP1)
ISO 3019-1 38-1 SAE J744-38-4 (C-C) SAE J744-32-4 (C)
in

Ports Tightening torques, max.2)

B Pressure port (high pressure range) SAE J518 1 1/4 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.75 (19) deep 66 lb-ft (90 Nm)
S Inlet port (standard pressure range) SAE J518 2 1/2 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.94 (27) deep 66 lb-ft (90 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 1 1/16-12 UN-2B 265 lb-ft (360 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 25/36

Before finalising your design, please

Unit dimensions, Size 140 request a certified installation drawing.
Dimensions in inches (mm).
Version AA10VSO 140 XXXX/31X-XXX62N00
View W mech.
displacement
limiter max.

Flange SAE J744

152-4 (D)
mech.
displacement
limiter min.

mech.
View V
displacement
limiter min.

mech. displacement
limiter
mech.
displacement
limiter max.

Shaft ends
K Parallel with key S Splined shaft 1 3/4 in 13T 8/16 DP1)
ISO 3019-1 44-1 SAE J744-44-4 (D)

Ports Tightening torques, max.2)

B Pressure port (high pressure range) SAE J518 1 1/4 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.75 (24) deep 66 lb-ft (90 Nm)
S Inlet port (standard pressure range) SAE J518 2 1/2 in
Threading in bolt holes ISO 68 1/2-13 UNC-2B; 0.94 (24) deep 66 lb-ft (90 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 1 1/16-12 UN-2B 265 lb-ft (360 Nm)
1)
ANSI B92.1a-1976, pressure angle 30°, flat root side fit, tolerance class 5
2)
See safety information
26/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Through drives
Axial piston units (A)A10VSO can be supplied with a through drive as shown in the ordering code on page 3. The type of through
drive is determined by codes (K40-K...). If the combination pump is not mounted in the factory, the simple type code is sufficient.
Included in this case are: shaft coupler, seals, and if necessary an adapter flange.
Maximum permissible input and through drive torque.

Ttot Tthr

The drive torques for pump 1 and pump 2 can be split up as required. However the max. permissible input torque Ttot as well as
the max. permissible through drive torque Tthr may not be exceeded.

Max. perm. input torque Ttot 18 28 45 71 100 140With shaft

U Ttot lb.ft (Nm) 43 (59) - (-) 139 (188) - (-) 439 (595) - (-)
With shaft K Ttot lb.ft (Nm) 77 (104) 107 (145) 156 (212) 319 (433) 553 (750) 875 (1186)
With shaft S Ttot lb.ft (Nm) 92 (124) 146 (198) 235 (319) 462 (626) 814 (1104) 1195 (1620)
With shaft R Ttot lb.ft (Nm) 111 (150) 166 (225) 295 (400) 475 (644) - (-) - (-)
Max. perm. through drive torque Tthr
With shaft K Tthr lb.ft (Nm) 77 (104) 107 (145) 156 (212) 319 (433) 553 (750) 875 (1186)
With shaft S Tthr lb.ft (Nm) 80 (108) 118 (160) 235 (319) 363 (492) 574 (778) 934 (1266)
With shaft R Tthr lb.ft (Nm) 88 (120) 130 (176) 269 (365) 404 (548) - (-) - (-)
Keyed shaft Tthr keyed lb.ft (Nm) 53 (72) 83 (112) 132 (179) 209 (283) 293 (398) 411 (557)
Ttot = max. permissible input torque pump 1
Tthr = max. permissible through drive torque
Tthr keyed = max. permissible through drive torque at through drive to keyed shaft

Permissible overhang moment

m1, m2, m3 weight of pump [lbs (kg)]
l1, l2, l3 distance to center of gravity [in (mm)]
1
Tm = (m1 • l1 + m2 • l3 + m3 • l3) • [lb.ft]
12
1
... • [Nm]
102

Size 18 28 45 71 100 140

Permissible overhang moment Tm lb.ft (Nm) 369 (500) 649 (880) 1010 (1370) 1593 (2160) 2213 (3000) 3319 (4500)
at dyn. acceleration Tm lb.ft (Nm) 37 (50) 65 (88) 101 (137) 159 (216) 221 (300) 332 (450)
10g = 98.1 m/s2
Weight m lbs (kg) 26,5 (12) 33 (15) 46 (21) 73 (33) 99 (45) 132 (60)
Distance to center of gravity l1 in (mm) 3.54 (90) 4.33 (110) 5.12 (130) 5.91 (150) 6.30 (160) 6.30 (160)
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 27/36

Before finalising your design, please

Overview of through drive mounting options request a certified installation drawing.
Dimensions in inches (mm).

Through drives - (A)A10VSO Mounting option - 2nd pump

Flange hub code (A)A10VSO.../31... A10V(S)O.../52 gear pump aviable on
SAE J744 keyed size (shaft) size (shaft) size
82-2(A) keyed (A-B) K40 18 (K) 10 (K) - 18-100
101-2 (B) keyed (B) K03 28 (K) 28 (K) - 28-140
101-2 (B-B) keyed (B-B) K05 45 (K) 60, 45 (K) - 45-140
127-2 (C) keyed (C) K08 71 (K) - - 71-140
127-2 (C) keyed (C) K38 100 (K) 85 (K) - 100-140
152-4 (D) keyed (D) K21 140 (K) - - 140

SAE J744 splined

82-2 (A) 5/8 in (A) K01 18 (U) - size F 18-140
82-2 (A) 3/4 in (A-B) K52 18 (S, R) 10 (S) - 18-140
101-2 (B) 7/8 in (B) K68 28 (S, R) 28 (S, R) size N, G 28-140
1) 1)
45 (U) 45 (U, W)
101-2 (B) 1 in (B-B) K04 45 (S, R) 45 (S, R) - 45-140
60 (U, W)2)
127-2 (C) 1 1/4 in (C) K07 71 (S, R) 85 (U, W)3) - 71-140
3)
100 (U)
127-2 (C) 1 1/2 in (C-C) K24 100 (S) 85 (S) - 100-140
152-4 (D) 1 3/4 in (D) K17 140 (S) - - 140
1)
Not with K68 through drive on main pump size 28
2)
Not with K04 through drive on main pump size 45
3)
Not with K07 through drive on main pump size 71
28/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Unit dimensions combination pumps request a certified installation drawing.
Dimensions in inches (mm).

(A)A10VSO (2nd pump) (A)A10VSO (2nd pump)

st st
(1 pump) 18 28 45 71 100 140 (1 pump) 18 28 45 71 100 140
18 A1 145 18 A1 5.71
A2 182 A2 7.16
A3 327 A3 12.87
A4 377 A4 14.84
28 A1 165 165 28 A1 6.49 6.49
A2 204 204 A2 8.03 8.03
A3 349 368 A3 13.74 14.49
A4 399 410 A4 15.71 16.14
45 A1 184 184 184 45 A1 7.24 7.24 7.24
A2 229 229 229 A2 9.02 9.02 9.02
A3 374 393 413 A3 14.72 15.47 16.26
A4 424 435 453 A4 16.69 17.13 17.83
71 A1 217 217 217 217 71 A1 8.54 8.54 8.54 8.54
A2 267 267 267 267 A2 10.51 10.51 10.51 10.51
A3 412 431 451 484 A3 16.22 16.97 17.76 19.06
A4 462 473 491 524 A4 18.19 18.62 19.33 20.63
100 A1 275 275 275 275 275 100 A1 10.83 10.83 10.83 10.83 10.83
A2 338 338 338 338 338 A2 13.31 13.31 13.31 13.31 13.31
A3 483 502 522 555 613 A3 19.02 19.76 20.55 21.85 24.13
A4 533 544 562 595 667 A4 20.98 21.42 22.13 23.43 26.26
140 A1 275 275 275 275 275 275 140 A1 10.83 10.83 10.83 10.83 10.83 10.83
A2 350 350 350 350 350 350 A2 13.78 13.78 13.78 13.78 13.78 13.78
A3 495 514 534 567 625 625 A3 19.49 20.24 21.02 22.32 24.61 24.61
A4 545 556 574 607 679 688 A4 21.46 21.89 22.60 23.90 26.73 27.09

Dimensions in millimeters Dimensions in inches

1. If a second Rexroth pump must be factory mounted the

two individual model codes must be combined with a “+“.
Model code pump 1+ model code pump 2.
Ordering example:

(A)A10VSO (A)A10VSO AA10VSO71 DR/31 L-PKC92K68 + AA10VSO28 DR/31L-

(1st Pump) (2nd Pump) PSC62N00
2. If a gear pump or a radial piston pump is to be factory
mounted as a second pump please consult the factory.
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 29/36

Before finalising your design, please

Dimensions of through drives request a certified installation drawing.
Dimensions in inches (mm).
K401) Flange SAE J744 - 82-2 (A)
Hub for keyed shaft to ISO 3019-1 19-1
Size A1 A3 A4
section A - B
28 8.03 (204) 0.63 (16) 1.85 (47)
45 9.02 (229) 0.63 (16) 2.09 (53)
71 10.51 (267) 0.79 (20) 2.40 (61)
omitted on
size 28
100 13.31 (338) 0.79 (20) 2.56 (65)
140 13.78 (350) 0.67 (17) 3.03 (77)

omitted on
size 28
thread
metric
to pump mounting flange

K031) Flange SAE J744 - 101-2 (B)

Hub for keyed shaft to ISO 3019-1 22-1
Size A1 A3 A4
section A - B
28 8.03 (204) 0.71 (18) 1.85 (47)
A
0.25 (6.38)
45° A4 45 9.02 (229) 0.71 (18) 2.09 (53)
0.31 (8)
omitted on 71 10.51 (267) 0.79 (20) 2.40 (61)
size 28
(Ø22.225+0.03)

100 13.31 (338) 0.79 (20) 2.56 (65)

DIA 0.8750
0.8762

140 13.78 (350) 0.79 (20) 3.03 (77)

+0.020 )
(Ø101.6 +0.050
DIA 4.0008
4.0020
(25.22)
0.99

5.75
DIA 146)
(Ø

omitted on
thread
M12

size 28 0.39 (10)

B metric
A3
to pump mounting flange A1

K051) Flange SAE J744 - 101-2 (B-B)

Hub for keyed shaft SAE to ISO 3019-1 25-1
Size A1 A3 A4
A section A - B
45 9.02 (229) 0.71 (18) 2.09 (53)
45° A4
0.25 (6.38) 0.31 (8) 71 10.51 (267) 0.79 (20) 2.40 (61)
omitted on
size 28 100 13.31 (338) 0.79 (20) 2.56 (65)
(Ø25.4+0.03)
DIA 1.0000
1.0012

140 13.78 (350) 0.79 (20) 3.03 (77)

+0.020 )
(Ø101.6 +0.050
DIA 4.0008
4.0020
(28.4)
1.12

5.75
DIA 146)
(Ø

omitted on
thread
M12

size 28
0.39 (10) metric
B A3
to pump mounting flange A1
1)
Not for new projects. Permitted with reduced through drive
torque only (see page 26).
30/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Dimensions of through drives request a certified installation drawing.
Dimensions in inches (mm).
K081) Flange SAE J744 - 127-2 (C)
Hub for keyed shaft to ISO 3019-1 32-1
Size A1 A3 A4
section A - B
71 10.51 (267) 0.71 (18) 2.40 (61)
100 13.31 (338) 0.95 (24) 2.52 (64)
omitted on 140 13.78 (350) 0.95 (24) 2.62 (66,5)
size 28

omitted on
size 28 thread
metric
to pump mounting flange

K381) Flange SAE J744 - 127-2 (C)

Hub for keyed shaft SAE to ISO 3019-1 38-1
Size A1 A3 A4
section A - B
100 13.31 (338) 0.95 (24) 2.56 (65)
140 13.78 (350) 0.95 (24) 3.03 (77)

thread
metric
to pump mounting flange

K211) Flange SAE J744 - 152-4 (D)

Hub for keyed shaft to ISO 3019-1 44-1
Size A1 A3 A4
section A - B
140 13.78 (350) approx. 0.83 (ca. 21) 3.03 (77)

thread
metric
to pump mounting flange
1)
Not for new projects. Permitted with reduced through drive
torque only (see page 26).
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 31/36

Before finalising your design, please

Dimensions of through drives request a certified installation drawing.
Dimensions in inches (mm).
K01 Flange SAE J744 - 82-2 (A)
Hub for splined shaft to ANSI B.92.1a-1976 5/8 in 9T 16/32 DP1) (SAE J744 - 16-4 (A))
Size A1 A3 A4
section A - B
18 7.16 (182) 0.57 (14,5) 1.65 (42)
28 8.03 (204) 0.63 (16) 1.85 (47)
45 9.02 (229) 0.63 (16) 2.09 (53)
71 10.51 (267) 0.79 (20) 2.40 (61)
100 13.31 (338) 0.79 (20) 2.56 (65)
140 13.78 (350) 0.63 (17) 3.03 (77)

thread
to pump mounting flange metric

K52 Flange SAE J744 - 82-2 (A)

Hub for splined shaft to ANSI B.92.1a-1976 3/4 in 11T 16/32 DP1) (SAE J744 - 19-4 (A-B))
Size A1 A2 A3 A4 A5
section A - B
18 7.16 1.57 0.74 1.69 M10; 0.57 (14,5) deep
45
°
(182) (40) (18,8) (43)
A A4
A3 28 8.03 1.53 0.74 1.85 M10; 0.63 (16) deep
(204) (39) (18,8) (47)
45 9.02 1.59 0.75 2.09 M10; 0.63 (16) deep
+0.020 )

9
4.1
+0.050

DIA 06.5)
3.2520
DIA3.2508

1 (229) (40,5) (18,9) (53)

A5 (ø82.55

(ø

71 10.51 1.57 0.84 2.40 M10; 0.79 (20) deep

(267) (40) (21,3) (61)
0.39 (10) 100 13.31 1.57 0.75 2.56 M10; 0.79 (20) deep
B A5 A2
to pump mounting flange A1 thread (338) (40) (19) (65)
metric
140 13.78 1.61 0.75 3.03 M10; 0.67 (17) deep
(350) (41) (18,9) (77)

K68 Flange SAE J744 - 101-2 (B)

Hub for splined shaft to ANSI B.92.1a-1976 7/8 in 13T 16/32 DP1) (SAE J744 - 22-4 (B))
Size A1 A2 A3 A4 A5
section A - B
28 8.03 1.69 0.70 1.85 M12; 0.71 (18) deep
45
A A4 (204) (43) (17,8) (47)
omitted on A3
size 28 45 9.02 1.65 0.70 2.09 M12; 0.71 (18) deep
(229) (42) (17,9) (53)
9
4.1
A 71 10.51 1.69 0.80 2.40 M12; 0.79 (20) deep
DI 46)
(ø101.6 +0.020)
+0.050

(ø1
3.2520
DIA 3.2508

(267) (43) (20,3) (61)

100 13.31 1.61 0.71 2.56 M12; 0.79 (20) deep
(338) (41) (18) (65)
A5

10 140 13.78 1.73 0.70 3.03 M12; 0.79 (20) deep

B A2
to pump mounting flange A1 thread
(350) (44) (17,9) (77)
metric
1)
pressure angle 30°, flat root side fit, tolerance class 5
32/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Before finalising your design, please

Dimensions of through drives request a certified installation drawing.
Dimensions in inches (mm).
K04 Flange SAE J744 - 101-2 (B)
Hub for splined shaft to ANSI B.92.1a-1976 1 in 15T 16/32 DP1) (SAE J744 - 25-4 (B-B))
Size A1 A2 A3 A4 A5
section A - B
45
45 9.02 1.87 0.73 2.09 M12; 0.71 (18) deep
A A4
A3 (229) (47,5) (18,4) (53)
71 10.51 1.87 0.82 2.40 M12; 0.79 (20) deep
5 (267) (47,5) (20,8) (61)
5.7
DIA 46)

(ø101,6+0,020)
+0,050
1 100 13.31 1.87 0.72 2.56 M12; 0.79 (20) deep

4.0020
DIA4.0008
(ø

(338) (47,5) (18,2) (65)

140 13.78 1.87 0.73 3.03 M12; 0.79 (20) deep

A5
(350) (47,5) (18,4) (77)
0.39 (10)
B A2
to pump mounting flange A1
thread
metric

K07 Flange SAE J744 - 127-2 (C)

Hub for splined shaft to ANSI B.92.1a-1976 1 1/4 in 14T 12/24 DP1) (SAE J744 - 32-4 (C))
Size A1 A2 A3 A4 A5
section A - B
71 10.51 2.18 0.87 2.40 M16; 0.70 (18) deep
45
A5
A thread
A4 (267) (55,5) (22) (61)
omitted on A3
metric 100 13.31 2.24 0.77 2.56 M16; 0.95 (24) deep
size 71
omitted on
size 71
(338) (57) (19,5) (65)
(ø127 +0.020 )

7.13
+0.050

DIA 1) 140 13.78 2.36 0.77 3.03 M16; 0.95 (24) deep
5.0020
DIA 5.0008

(ø18
(350) (60) (19,4) (77)

B 0.51 (13)
A2
to pump mounting flange A1

K24 Flange SAE J744 - 127-2 (C)

Hub for splined shaft to ANSI B.92.1a-1976 1 1/2 in 17T 12/24 DP1) (SAE J744 - 38-4 (C-C))
Size A1 A3 A4
section A - B
100 13.31 (338) 0.95 (24) 2.56 (65)
140 13.78 (350) 0.95 (34) 3.03 (77)

thread
to pump mounting flange metric

1)
pressure angle 30°, flat root side fit, tolerance class 5
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 33/36

Before finalising your design, please

Dimensions of through drives request a certified installation drawing.
Dimensions in inches (mm).
K17 Flange SAE J744 - 152-4 (D)
Hub for splined shaft to ANSI B.92.1a-1976 1 3/4 in 13T 8/16 DP1) (SAE J744 - 44-4 (D))
Size A1 A3 A4
section A - B
140 13.78 (350) approx. 0.83 (ca. 21) 3.03 (77)

thread
to pump mounting flange metric
34/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Installation notes ρ =density [kg/m3]

l = pipe lenth [m]
Optional installation position.The pump housing must be filled dv/dt = rate of change in fluid velocity[m/s2]
with fluid during commissionig and operation. ∆p2: Pressure lodd due to static head
In order to attain the lowest noise level, all connections ∆p2 = h . ρ . g . 10–5 [bar]
(suction, pressure, pilot, case drain) must be linked by flexible h = head [m]
members to tank. ρ = density [kg/m3]
g = gravity. = 9,81 m/s2
Avoid placing a check valve in the case drain line.
∆p3: line losses (elbows etc.)
The case drain hose corresponding to the size of the case
drain port should be installed at the highest case drain port Horizontal installation
location. The pump must be installaed in such a manner, that either “L“
Vertical installation (shaft end upwards) or “L1“ is at the top.
Following installation conditions must be taken into account:
Arrangement inside the reservoir
Arrangement inside the reservoir a) If the min. fluid level is above the top of the pump:
Before installation fill pump housing, keeping it in a horizontal Close “L1” , "L" and “S” open, mount suction pipe to port S,
position. and pipe “L“ at least 200 mm away from suction pipe.
a) If the min. fluid level is equal to or above the pump mounting (see. fig. 3)
surface: b)If the min. fluid level is equal to or below the top of the pump:
Close port “L“, "L1" and “S” open; L1 piped and also S with Pipe port "L" and "S" acc.to.fig. 4 , port "L1" closed.
suction pipe (see fig. 1). (compare limiting conditions)
b) If the min. fluid level is below the pump mounting surface: Note: In order to avoid demages to the pump, all attached
pipe port “L“ and “S“ acc. to fig. 2, close port “L“ (compare parts (e.g. protective caps, covers, etc.) must be removed
item limiting conditions) before installation.
Note: In order to avoid demages to the pump, all attached
Fluid
parts (e.g. protective caps, covers, etc.) must be removed min. 8 in (200mm)
before installation. L
Fluid

ht min
L S
L1 L1
min. 8 in (200mm) fig. 3
S
fig. 1 Arrangement outside the reservoir
Arrangement outside the reservoir Fill pump housing before commissioning.
Before installation fill pump housing while keeping it in a Pipe port “S“ and the higher port “L“ or “L1“
horizontal position. For mounting above the tank see fig. 2. a) When mounting above the reservoir: see fig. 4 (compare
item limiting conditions)
Limiting condition:
b) Mounting below the reservoir: pipe ports “L“ and “S“
Min. pump inlet pressure pabs min = 12 psi (0,8 bar) under static
according to fig. 5, “L“ closed.
and dynamic loading.
Note: Avoid mounting above tank wherever possible in order to
attain a low noise level. L
S
The permissible suction height h is a result of the overall
pressure loss, but may not be greater than hmax = 31.5 in (800
mm) (Immersion depth ht min = 8 in/200 mm). Fluid
ht min hmax

L1
L1 L
baffle
S fig. 4
ht min hmax

Fluid

Fluid
baffle fig. 2
ht min

Overall pressure loss baffle

∆pGes = ∆p1 + ∆p2 + ∆p3 ≤ (1 – pabs min) = 0,2 bar L1
∆p1: Pressure loss inpipe due to accelerating column of fluid
S
ρ . l . dv . –5
∆p1 = 10 [bar]
dt L fig. 5
RA 92 711/05.04 | (A)A10VSO Industrial Hydraulics | Bosch Rexroth AG 35/36

Safety information
– Pump (A)A10VSO was designed for operation in open loop circuits.
– Systems design, installation and commissioning require trained technicians or tradesmen.
– All hydraulic ports can only be used for the fastening of hydraulic service lines.
– Tightening torques:
The tightening torques mentioned in this data sheet are maximum values and must not be exceeded (max. values for thread).
Manufacturers information concerning the maximum permitted tightening torques of the various fittings is to be observed!
For ISO68/DIN 13 mounting bolts, we recommend that tightening torques be checked on a case by case basis in accordance
with VDI 2230, published 2003.
– During and shortly after operation of a pump the housing and especially a solenoid can be extremely hot, avoid being burned!
36/36 Bosch Rexroth AG | Industrial Hydraulics (A)A10VSO | RA 92 711/05.04

Bosch Rexroth Corporation © 2004 Bosch Rexroth Corporation

Mobile Hydraulics All rights reserved. Neither this document, nor any part of it, may be reproduced,
Axial & Radial Piston Units duplicated, circulated or disseminated, whether by copy, electronic format or any
8 Southchase Court other means, without the prior consent and authorization of Bosch Rexroth
Fountain Inn, SC 29644-9018 Corporation.
USA The data and illustrations in this brochure/data sheet are intended only to
Telephone (864) 967-2777 describe or depict the products. No representation or warranty, either express or
Facsimile (864) 967-8900 implied, relating to merchantability or fitness for intended use, is given or
www.boschrexroth-us.com intended by virtue of the information contained in this brochure/data sheet. The
information contained in this brochure/data sheet in no way relieves the user of
its obligation to insure the proper use of the products for a specific use or
application. All products contained in this brochure/data sheet are subject to
normal wear and tear from usage.