Manual de Installacion BUC

IBUC G
Intelligent Block Upconverter
Operations Manual
24-Hour Technical Support: +1 408.782.2166

This document is provided to customers who have purchased Terrasat Communications, Inc.
equipment. This document is copyright protected and no part of this manual may be reproduced,
transcribed, or translated into any language or transmitted in any form whatsoever without the
prior written consent of Terrasat Communications, Inc.
Technical information contained in this publication is for reference purposes only and is subject
to change without notice. Every effort has been made to supply complete and accurate
information; however, Terrasat Communications, Inc. assumes no responsibility and will not be
liable for any errors, omissions, damage, or loss that might result from any use of this manual or
the information contained therein (even if this information is properly followed and problems still
arise).
Part Number: O&M-22063-0001

Revision: A
© November 2013 Terrasat Communications, Inc.
235 Vineyard Court Phone: +1 408.782.5911

Morgan Hill, CA 95037 FAX: +1 408.782.5912
www.terrasatinc.com
TABLE OF CONTENTS
Preface
Conventions and References .................................................................................................... P-1
Cautions and Warnings ..................................................................................................... P-2
Trademarks........................................................................................................................ P-2
Electrical Safety Notice .................................................................................................... P-2
Chapter 1, Introduction
Block Upconverters.................................................................................................................. 1-1
Reference Documents .............................................................................................................. 1-1
Warranty Information............................................................................................................... 1-4
Export Regulations................................................................................................................... 1-5
Chapter 2, Functional Description

Introduction .............................................................................................................................. 2-1
System Components................................................................................................................. 2-1
AC Supply............................................................................................................................ 2-4
Fuses..................................................................................................................................... 2-4
Monitor and Control............................................................................................................. 2-5
RF Signal Flow .................................................................................................................... 2-5
Software ............................................................................................................................... 2-9
System Configurations......................................................................................................... 2-10
Storage Information ............................................................................................................. 2-12
Chapter 3, Installation
Introduction .............................................................................................................................. 3-1
General Requirements .............................................................................................................. 3-1
Unpacking ......................................................................................................................... 3-1
Furnished Items................................................................................................................. 3-2
Accessories........................................................................................................................ 3-3
Installing the ODU ............................................................................................................... 3-4
Tools.................................................................................................................................. 3-4
Test Equipment ................................................................................................................. 3-4
Site Considerations ........................................................................................................... 3-4
Mounting Considerations.................................................................................................. 3-4
Power Requirements ......................................................................................................... 3-5
Grounding ......................................................................................................................... 3-6
Antenna Recommendations .............................................................................................. 3-6
Antenna Mounting ............................................................................................................ 3-7
System Pressurization ....................................................................................................... 3-8
System Cabling Requirements .......................................................................................... 3-9
i
Cable and Waveguide Connections .................................................................................. 3-11
Basic System Alignment ...................................................................................................... 3-15
Setting the Tx and Rx Frequencies ................................................................................... 3-15
Transmit Power Alignment ............................................................................................... 3-15
Transmit RF Output Adjustment with Modem or Converter (70 MHz to L-band) .......... 3-16
Final Checks ............................................................................................................................. 3-17
Chapter 4, Operations
Introduction .............................................................................................................................. 4-1
Start-up Checklist ..................................................................................................................... 4-1
Turning On the IBUC G ...................................................................................................... 4-2
Setting Operating Parameters............................................................................................... 4-2
Setting the Tx Frequency (L-band) ................................................................................... 4-4
Setting Alarm Thresholds ................................................................................................. 4-4
Configuring Alarm States ................................................................................................. 4-5
Configuring ALC/AGC..................................................................................................... 4-5
Configuring the External Mute ......................................................................................... 4-6
Common Errors ........................................................................................................................ 4-7
LED is Red........................................................................................................................ 4-7
No Power to the IBUC G.................................................................................................. 4-7
Time Stamp Data is Incorrect ........................................................................................... 4-8
Satellite Network Operations Center Doesn’t Recognize Signal...................................... 4-8
Transmit Power in Saturation............................................................................................ 4-8
Tx Input/Output Level Verification .................................................................................. 4-9
Chapter 5, Monitor and Control Features

Introduction .............................................................................................................................. 5-1
M&C Interfaces........................................................................................................................ 5-1
RS232................................................................................................................................... 5-1
Hand-held Terminal ............................................................................................................. 5-2
Multifunction LED............................................................................................................... 5-4
Frequency Shift Keying (FSK) Modem Interface................................................................ 5-5
RS485................................................................................................................................... 5-6
ASCII Mode ...................................................................................................................... 5-6
Legacy Binary Mode......................................................................................................... 5-8
Ethernet ................................................................................................................................ 5-9
Determining the IP Address of Your IBUC or IBUC G................................................... 5-9
Telnet................................................................................................................................. 5-18
Web Server........................................................................................................................ 5-18
SNMP................................................................................................................................ 5-19
Power Measurement ................................................................................................................. 5-21
Chapter 6, Troubleshooting
Maintenance ............................................................................................................................. 6-1
Transceiver Fault Isolation................................................................................................... 6-1
ii
AC Power Problems/Conditioning ....................................................................................6-1
Site-Related Problems .......................................................................................................6-2
M&C Checks .....................................................................................................................6-2
Transmit Power Setting .....................................................................................................6-3
Common Problems ...............................................................................................................6-4
Tx Output is Disabled........................................................................................................6-4
Incorrect Frequency Settings .............................................................................................6-4
Damaged Cables ................................................................................................................6-4
10 MHz Reference Signal at the IBUC G is at the Wrong Level or Missing ..................6-4
Antenna is Pointed Toward Wrong Satellite or is Misaligned ..........................................6-5
Moisture Migrated Into the IBUC G ................................................................................6-5
Bad Orthogonal Mode Transducer and/or Antenna ..........................................................6-6
LED is Red ........................................................................................................................6-6
Repair Policy.............................................................................................................................6-7
Returned Material Authorization (RMA) .............................................................................6-7
Chapter 7, Transmit Redundant Systems

Description................................................................................................................................7-1
Interface for Tx Redundant (1+1) Systems ..........................................................................7-3
Component Descriptions...........................................................................................................7-5
Intelligent Block Upconverter (IBUC G) ............................................................................7-5
Tx 1+1 Interface Module......................................................................................................7-5
Waveguide Switch................................................................................................................7-6
Software................................................................................................................................7-6
Installation and Setup................................................................................................................7-7
System Cabling Requirements..............................................................................................7-8
Tx 1+1 System...................................................................................................................7-8
Tx 1+1 Interface Module...................................................................................................7-9
Cable and Waveguide Connections ......................................................................................7-13
Water-Resistant Wrap........................................................................................................7-13
Typical Initial Setup ..........................................................................................................7-14
Water-Resistant Wrap........................................................................................................7-14
Grounding.............................................................................................................................7-15
Tx Redundancy Grounding Recommendations.................................................................7-15
System Alignment and Operation.............................................................................................7-16
General..................................................................................................................................7-16
Test Equipment.....................................................................................................................7-17
Setting the Tx Frequencies ...................................................................................................7-17
Tx Power Alignment .........................................................................................................7-17
Final Checks .............................................................................................................................7-18
M&C Setup...........................................................................................................................7-19
Service and Maintenance ..........................................................................................................7-26
Standard Maintenance ..........................................................................................................7-26
Fault Isolation .......................................................................................................................7-26
Common Problems ............................................................................................................7-28
iii
M&C Functions.................................................................................................................... 7-29
User Interfaces .................................................................................................................. 7-29
Repair Policy ............................................................................................................................ 7-32
Appendix A, Part Numbering Schema

Identifying the Part and Serial Numbers .................................................................................. A-1
Appendix B, Using HyperTerminal

Establishing a HyperTerminal Session .................................................................................... B-1
Using a Saved Connection ....................................................................................................... B-7
Ending a HyperTerminal Session............................................................................................. B-8
Appendix C, IBUC G Web Pages

Introduction .............................................................................................................................. C-1
Screen Shots ............................................................................................................................. C-5
Login ................................................................................................................................. C-5
Information Tab ................................................................................................................ C-6
Alarm Tab ......................................................................................................................... C-8
Sensor Tab......................................................................................................................... C-12
Transmit Configuration Tab.............................................................................................. C-14
Interface Configuration Tab.............................................................................................. C-19
System Configuration Tab ................................................................................................ C-22
Alarm Configuration Tab.................................................................................................. C-24
Redundancy Configuration Tab ........................................................................................ C-27
Alarm Log Tab.................................................................................................................. C-29
Appendix D, Hand-held Terminal Menu Tree

Menu Options ........................................................................................................................... D-1
Info & Sensors................................................................................................................... D-4
Tx ...................................................................................................................................... D-4
Alarm................................................................................................................................. D-5
Tx Thresholds.................................................................................................................... D-5
Interface............................................................................................................................. D-5
SNMP................................................................................................................................ D-6
System ............................................................................................................................... D-6
Redundancy....................................................................................................................... D-7
Appendix E, Legacy Binary Command Message Structure

Command Set ........................................................................................................................... E-1
Legacy Response Message Structure ....................................................................................... E-3
Data Field Definitions .......................................................................................................... E-5
Appendix F, ASCII Command/Response Structure

Command Set ........................................................................................................................... F-1
iv
Common Commands ............................................................................................................F-4
Receive-only Commands......................................................................................................F-17
Transmit-only Commands ....................................................................................................F-24
Redundancy Commands .......................................................................................................F-40
Appendix G, Component Specifications and Reference Drawings

Reference Drawings..................................................................................................................G-1
Data Sheets ...............................................................................................................................G-12
Appendix H, Glossary
Glossary of Terms.....................................................................................................................H-1
Index
v
This page intentionally left blank
for double-sided printing.
vi
LIST OF FIGURES
Figure 2.1 Front Panel of an IBUC G ......................................................................................... 2-4

Figure 2.2 IBUC G Block Diagram ............................................................................................ 2-8
Figure 2.3 IBUC G System Configuration................................................................................. 2-11
Figure 3.1 Contents of an IBUC G Shipping Carton.................................................................. 3-3
Figure 3.2 Location of Mounting Holes of an IBUC G.............................................................. 3-7
Figure 3.3 Location of Adjustment Slots on Optional Mounting Bracket .................................. 3-8
Figure 3.4 Applying the Anti-Seize Lubricant ............................................................................ 3-13
Figure 3.5 Waveguide Label and Channel for Gasket ................................................................ 3-14
Figure 5.1 IBUC G Hand-held Terminal .................................................................................... 5-3
Figure 5.2 Download Wireshark Icon ......................................................................................... 5-10
Figure 5.3 Wireshark Release Version........................................................................................ 5-10
Figure 5.4 Executable Alert Message.......................................................................................... 5-11
Figure 5.5 Open File Security Warning Message ....................................................................... 5-11
Figure 5.6 Installation Wizard Welcome..................................................................................... 5-12
Figure 5.7 Wireshark License Agreement................................................................................... 5-12
Figure 5.8 Choosing Wireshark Components ............................................................................. 5-13
Figure 5.9 Selecting Additional Wireshark Tasks....................................................................... 5-13
Figure 5.10 Choosing the Installation Location ............................................................................ 5-14
Figure 5.11 Installing WinPcap..................................................................................................... 5-14
Figure 5.12 Installation Progress Bar ............................................................................................ 5-15
Figure 5.13 WinPcap Installer....................................................................................................... 5-15
Figure 5.14 Setup Completion Notification .................................................................................. 5-16
Figure 5.15 Finishing Setup of Wireshark .................................................................................... 5-16
Figure 5.16 Wireshark Menu......................................................................................................... 5-17
Figure 5.17 Selecting An Interface................................................................................................ 5-17
Figure 5.18 Returning IP Address Information............................................................................. 5-18
Figure 7.1 Transmit Redundant System Setup ............................................................................ 7-2
Figure 7.2 Waveguide Connecting Two IBUC G Units ............................................................ 7-2
Figure 7.3 IBUC G Redundant System Diagram ....................................................................... 7-4
Figure 7.4 Tx 1+1 Interface Module Block Diagram.................................................................. 7-6
Figure 7.5 Tx 1+1 Interface Module Top View .......................................................................... 7-9
Figure 7.6 Multifunction LEDs for a Tx 1+1 System ................................................................. 7-25
Figure 7.7 Hand-Held Terminal .................................................................................................. 7-30
Figure A.1 Identifying the Part and Serial Numbers.................................................................... A-1
Figure A.2 Part Numbering Schema for IBUC Gs, IBUC 2s, and IBRs .................................... A-2
Figure A.3 Part Numbering Schema for IBUCs .......................................................................... A-3
Figure A.4 Part Numbering Schema for Transmit Redundant (Tx 1+1) Systems ....................... A-4
Figure A.5 Part Numbering Schema for Receive Redundant (Rx 1+1) Systems ........................ A-5
Figure A.6 Part Numbering Schema for IBUC with PSUI Systems............................................ A-6
Figure A.7 Part Numbering Schema for IFU Systems................................................................. A-7
vii
Figure A.8 Part Numbering Schema for LNBs ............................................................................ A-8
Figure A.9 Part Numbering Schema for SSPAs .......................................................................... A-9
Figure A.10 Part Numbering Schema for Redundant SSPA 1+1 Systems .................................... A-10
Figure B.1 New Connection Description Window ...................................................................... B-2
Figure B.2 Connect To Window .................................................................................................. B-3
Figure B.3 COM1 Properties Window......................................................................................... B-4
Figure B.4 Invalid Password Error Message................................................................................ B-5
Figure B.5 ASCII Setup Window ................................................................................................ B-5
Figure B.6 Invalid Value Error Message ..................................................................................... B-6
Figure B.7 Active HyperTerminal Window................................................................................. B-7
Figure C.1 Choosing Network Connections ................................................................................ C-2
Figure C.2 Choosing the Internet Protocol (TCP/IP) Properties.................................................. C-3
Figure C.3 Typing the IP Address................................................................................................ C-3
Figure C.4 Invalid Subnet Mask Error Message .......................................................................... C-4
Figure C.5 Login.......................................................................................................................... C-5
Figure C.6 Information Tab ......................................................................................................... C-6
Figure C.7 Alarm Status Tab ....................................................................................................... C-8
Figure C.8 Sensor Tab ................................................................................................................. C-12
Figure C.9 Tx Configuration Tab ................................................................................................ C-14
Figure C.10 Interface Configuration Tab....................................................................................... C-19
Figure C.11 System Configuration Tab ......................................................................................... C-22
Figure C.12 Alarm Configuration Tab........................................................................................... C-24
Figure C.13 Redundancy Configuration Tab................................................................................. C-27
Figure C.14 Alarm Log Tab........................................................................................................... C-29
Figure D.1 Sample IBUC G HHT Display ................................................................................. D-2
Figure D.2 Sample IBUC G Info & Sensors Window ................................................................ D-2
Figure D.3 IBUC G Hand-held Terminal Menu Tree................................................................. D-3
Figure G.1 Fabrication Drawing, FBD-21012-XXXX, Rev A.................................................... G-2
Figure G.2 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 1 of 2 ................................ G-3
Figure G.3 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 2 of 2 ................................ G-4
Figure G.4 Fabrication Drawing, FBD-20606-XXXX, Rev A.................................................... G-5
Figure G.5 Outline Drawing, OLD-22191-0000, Rev A, page 1 of 3 ......................................... G-6
Figure G.8 Example Installation Drawing for Antenna Mounting, 339-44001-XXXX, 
Rev A, page 1 of 2 ................................................................................................... G-9
Figure G.9 Example Installation Drawing for Antenna Mounting, 339-44001-XXXX, 
Rev A, page 2 of 2 ................................................................................................... G-10
Figure G.10 Example Installation Drawing, IND-10521-0011, Rev A ......................................... G-11
viii
LIST OF TABLES
Table P.1 Typographical Conventions ........................................................................................ P-1

Table 1.1 Satellite Operation Standards...................................................................................... 1-1
Table 2.1 IBUC G Transmit Frequency Plans............................................................................ 2-3
Table 2.2 Fuse Markings............................................................................................................. 2-4
Table 2.3 Fuse Markings Explained ........................................................................................... 2-5
Table 2.4 Internal 10 MHz Reference Signal Parameters........................................................... 2-6
Table 2.5 Basic System Requirements........................................................................................ 2-10
Table 3.1 Recommended Test Equipment .................................................................................. 3-4
Table 3.2 IBUC G Interface Connector Schedule ...................................................................... 3-9
Table 3.3 Pin Assignments for IBUC G M&C Connector J2 .................................................... 3-10
Table 3.4 Pin Assignments for IBUC G AC Power Connector J3 ............................................. 3-11
Table 3.5 Pin Assignments for IBUC G Ethernet Connector J4 ................................................ 3-11
Table 5.1 Default Alarm Configuration ...................................................................................... 5-4
Table 5.2 Transmitter Link Specifications.................................................................................. 5-5
Table 5.3 Receiver Link Specifications ...................................................................................... 5-5
Table 5.4 ASCII Mode Command Format.................................................................................. 5-7
Table 5.5 Packet Format ............................................................................................................. 5-8
Table 5.6 IBUC G Data Packet Byte Configuration .................................................................. 5-8
Table 6.1 Possible Scenarios for IBUC Gs with an External 10 MHz Reference Signal.......... 6-5
Table 7.1 Tx 1+1 Interface Module Connector Schedule ........................................................... 7-9
Table 7.2 Pin Assignments for M&C Interface Connectors J1, J2, and J3................................. 7-10
Table 7.3 Pin Assignments for M&C Interface Connectors J4 and J6 ....................................... 7-10
Table 7.4 Pin Assignments for M&C Interface Connector J5, J7, J8, and J10........................... 7-11
Table 7.5 Pin Assignments for M&C Interface Connector J9 .................................................... 7-12
Table 7.6 Pin Assignments for M&C Interface Connector J11 .................................................. 7-13
Table 7.7 Recommended Test Equipment .................................................................................. 7-17
Table C.1 Default Values for Power Monitor Frequency............................................................ C-15
Table C.2 Default Values for the Burst Threshold ...................................................................... C-16
Table E.1 IBUC G Commands................................................................................................... E-1
Table E.2 Response to IBUC G Commands 0x01, 0x02, 0x03, 0x04, 0x08, and 0xFF ............ E-3
Table E.3 Response to IBUC G Commands 0x05 and 0x06 
(When Data Byte 1 of Command Message = 0x00) ................................................... E-3
Table E.4 Response to IBUC G Command 0x06 
(When Data Byte 1 of Command Message = 0x01) ................................................... E-4
Table E.5 Response to IBUC G Command 0x07 ....................................................................... E-4
Table E.6 Response to IBUC G Command 0x09 ....................................................................... E-4
Table E.7 Data Field Definitions................................................................................................. E-5
Table F.1 Alarm Mask ................................................................................................................ F-1
Table F.2 Alarm Flags................................................................................................................. F-2
Table F.3 Error Response Table.................................................................................................. F-3
ix
Table F.4 Default Values for the TAH, TAL, and TBT Commands .......................................... F-31
Table F.5 Default Values for the TFR Command .......................................................................F-34
x
REVISION HISTORY
Revision Date Description
A1RYember 2013 Initial Release
xi
xii
P REFACE
This manual provides information about the Terrasat Communications, Inc. line of
P
intelligent block upconverters (IBUC Gs) and transmit redundant systems.
Conventions and References

Before you start using this manual, it is important to understand the typographical
conventions and terms used in the documentation.
Table P.1 describes typographical conventions used in Terrasat Communications, Inc.

documentation. For definitions of specialized terms used in the documentation, see
Appendix H, Glossary.
Table P.1 Typographical Conventions

Convention Description/Example
Used to emphasize the importance of a point.
Emphasis
The IP Address must be a unique number.
References to a section in the same document are marked in blue and
are hyperlinked.
Internal cross-references
For more information, see Warranty Information on page 1-4.
Named Terrasat products and features are identified on first use.
Product and feature
names
...line of intelligent block upconverters (IBUCs).
References to other Terrasat publications. If the reference is hyperlinked,
it is also underscored.
Technical Publication
References
For detailed information, see the Terrasat Communications, Inc. IBUC
Operations Manual.
A special font marks text that you type.
User-entered values
At the password prompt, type MyPassword.
Cautions and Warnings
CAUTION
CAUTION indicates a hazardous situation
that, if not avoided, could result in minor or
moderate injury. CAUTION might also be
used to indicate other unsafe practices or
risks of property damage.
HIGH VOLTAGE
HIGH VOLTAGE indicates the presence of a
high-voltage hazard.
WARNING
WARNING indicates a potentially
hazardous situation that, if not avoided,
could result in death or serious injury.
Trademarks
Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
Electrical Safety Notice

This equipment has been designed to minimize exposure of personnel to hazards. All
operators and technicians must
• Know how to work around, with, and on high-voltage equipment.

• Exercise every precaution to ensure safety of personnel.
• Exercise extreme care when working near high voltages.
• Be familiar with the warnings in this manual.
P-2 | Preface
C HAPTER
1
INTRODUCTION
CHAPTER 1
This manual is intended for users of Terrasat Communications, Inc. IBUC G systems.
It contains information about
• Installation, operation, and maintenance of IBUC G systems

• Use of user interface protocols for remote monitor and control capabilities
Block Upconverters
The term “intelligent” block upconverter refers to the advanced features and monitor
and control capabilities of the IBUC G product. The IBUC G includes automatic gain
control (AGC) and automatic level control (ALC) features as well as internal
diagnostics. It also provides extensive monitoring and control through a menu of
software commands and alarms providing access to the numerous operating
parameters and features available in the unit. Access to features and monitor and
control (M&C) functions is provided via several methods including a hand-held
terminal, RS232, RS485, TCP/IP (Telnet, HTTP), UDP (SNMP) and FSK (frequency
shift keying) link via the IFL cable. The IBUC G is also fitted with a multifunction
LED for visual status indications.
Reference Documents
Use the satellite operation standards listed in Table 1.1 as reference documents.
Table 1.1 Satellite Operation Standards

Earth Station Standards
Performance Characteristics for Intermediate Data Rate Digital
Intelsat IESS 308/309
Carriers Using Convolutional Encoding and QPSK Modulation
Minimum Technical and Operational Requirements for Earth Stations
Eutelsat EESS 502 Transmitting to a Eutelsat Transponder for Non-Standard Structured
Types of SMS Transmissions. Standard M.
Block Upconverters | 1-1

Table 1.1 Satellite Operation Standards (Continued)
Earth Station Standards
Satellite Earth Stations (SES); Transmit-only or transmit-and-receive
very small aperture terminals (VSATs) used for communications
ETS 300-332
operating in the fixed satellite service (FSS) 6 GHz and 4 GHz
frequency bands.
Satellite Earth Stations (SES); Transmit/receive very small aperture
ETS 300-159 terminals (VSATs) used for data communications operating in the
fixed satellite service (FFS) 11/12/14 GHz frequency bands.
Satellite Earth Stations (SES); Control and monitoring functions for
ETS 300-160
very small aperture terminals (VSAT) networks.
Satellite Earth Stations and Systems (SES); Harmonized EN for Low
Data Rate Mobile Satellite Earth Stations (MESs) except aeronautical
mobile satellite earth stations, operating in the 11/12/14 GHz
ETSI EN 301 427
frequency bands covering essential requirements under article 3.2 of
the Radio & Telecommunications Terminal Equipment (R&TTE)
directive
Satellite Earth Stations and Systems (SES); Harmonized EN for Very
Small Aperture Terminal (VSAT); Transmit-only, transmit/receive, or
receive-only satellite earth stations operating in the 11/12/14 GHz
ETSI EN 301 428
the Radio & Telecommunications Terminal Equipment (R&TTE)
Directive.
Satellite Earth Stations and Systems (SES); Harmonized EN for
Satellite News Gathering Transportable Earth Stations (SNG TES)
ETSI EN 301 430
operating in the 11-12/13-14 GHz frequency bands covering essential
requirements under article 3.2 of the R&TTE directive
Satellite Earth Stations and Systems (SES); Harmonized EN for Very
Small Aperture Terminal (VSAT); Transmit-only, transmit/receive, or
ETSI EN 301 443 receive-only satellite earth stations operating in the 4 GHz and 6 GHz
the R&TTE Directive.
MIL-STD-188-164B Interoperability of SHF Satellite Communications Terminals .
ANSI/TIA/EIA 568 Commercial Building Telecommunications Cabling Standard
Environmental Standards
Equipment Engineering (EE): Environmental Conditions and
ETS 300 019-1-1 Environmental Tests for Telecommunications Equipment. Part 1-1:
Classification of environmental conditions. Storage.
Classification of environmental conditions. Transportation.
Environmental Tests for Telecommunications Equipment. Part 1-4:
ETS 300 019-1-4
Classification of environmental conditions. Stationary use at non-
weather protected locations.
Specification of environmental tests; Storage
1-2 | Introduction
Environmental Standards
ETS 300 019-2-2 Environmental Tests for Telecommunications Equipment. Part 2.2:
Specification of environmental tests; Transportation
Environmental Tests for Telecommunications Equipment. Part 2-4:
ETS 300 019-2-4
Specification of environmental tests; Stationary use at non-weather
protected locations
Materiel acquisition program planning and engineering direction for
MIL-STD-810F considering the influences that environmental stresses have on
materiel throughout all phases of its service life.
EMC/EMI Standards
The Radio and Telecommunications Terminal Equipment Directive
99/5/EEC
(R&TTE)
Electromagnetic Compatibility and Radio Spectrum Matters (ERM);
ETSI EN 301 489-1 v1.8.1 Electromagnetic Compatibility (EMC) standard for radio equipment
and services; Part 1: Common technical requirements
Electromagnetic Compatibility and Radio Spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment
and services; Part 12: Specific conditions for Very Small Aperture
ETSI EN 301 489-12 v2.2.2
Terminal, Satellite Interactive Earth Stations operated in the
frequency ranges from 4 GHz through 30 GHz in the Fixed Satellite
Services (FSS)
Information Technology Equipment – Radio Disturbance
EN 55022A
Characteristics – Limits and methods of measurement
Electromagnetic Compatibility (EMC) – Part 3.2: Limits for harmonic
EN 61000-3-2
current emissions (equipment input current < 16 A per phase)
Electromagnetic Compatibility (EMC) – Part 3.3: Limitation of voltage
changes, voltage fluctuations, and flicker in public low-voltage supply
EN 61000-3-3
systems for equipment with rated current ≤ 16 A per phase and not
subject to conditional connection
Electromagnetic Compatibility (EMC) – Part 4-2: Testing and
EN 61000-4-2
measurement techniques – Electrostatic discharge immunity test
EN 61000-4-3 measurement techniques – Radiated, radio-frequency,
electromagnetic field immunity test
EN 61000-4-4 measurement techniques – Electrical fast transient/burst immunity
test
EN 61000-4-5
measurement techniques – Surge immunity test
EN 61000-4-6 measurement techniques – Immunity to conducted disturbances,
induced by radio-frequency fields
Reference Documents | 1-3

EMC/EMI Standards
EN 61000-4-11 measurement techniques – Voltage dips, short interruptions, and
voltage variations immunity tests
Requirements for the Control of Electromagnetic Interference
MIL-STD-461E
Characteristics for Subsystems and Equipment
Safety Standards
2006/95/EC The Low Voltage Directive (supersedes 73/23/EEC)
Information technology equipment – Safety as applied to
mains-powered or battery-powered information technology
EN 60950-1
equipment, including electrical business equipment and associated
equipment, with a rated voltage not exceeding 600 V.
Warranty Information
Determination of warranty status of equipment shall be in accordance with the
following Terrasat Communications, Inc. Warranty Policy.
(A) This warranty is for equipment of Terrasat Communications, Inc. The term
“Terrasat” as used throughout this warranty shall mean Terrasat Communications,
Inc., if the equipment was manufactured by Terrasat Communications, Inc.
(B) Terrasat warrants that its equipment shall be free from defects in material or
workmanship at the time of shipment and that it will conform to applicable
specifications.
For all Satcom products, the buyer shall exercise any and all warranty claims within a
period of twenty-four (24) months.
(1) The warranty does not apply to any part of a product if it has been altered,
repaired, or misused in any way that, in the opinion of Terrasat, affects the
reliability of, or detracts from the performance of, any part of the product; or it is
damaged as a result of the use of such part in or in connection with equipment not
previously approved by Terrasat.
(2) The warranty does not apply to any product or parts thereof if its serial number
or the serial number of any of its parts has been altered, defaced, or removed.
(3) The warranty does not cover damages or losses incurred in transport.
(4) The warranty does not cover replacement or repair necessitated by loss or
damage resulting from cases beyond the control of Terrasat.
(5) The warranty does not include the furnishing of any labor involved or
connected with the removal and/or reinstallation of warranted equipment or parts
on site, or any labor required to diagnose the necessity for replacement or repair.
1-4 | Introduction
(6) In no event shall Terrasat be liable to buyer for any indirect, special, or
consequential damages or lost profits arising from the use of the equipment or
products, even if Terrasat has been advised of the possibility thereof, or for any
inability to use them either separated from or in combination with any other
equipment or products.
(C) Terrasat’s warranty, as stated herein, is in lieu of all other warranties, expressed,
implied or statutory, including those of merchantability and fitness for a particular
purpose, and Terrasat neither assumes nor authorizes any person to assume for it any
other obligation or liability to any person in connection with the sale or use of
Terrasat’s products. The buyer shall pass on to any purchaser, lessee, or other user of
Terrasat’s products, the aforementioned warranty and shall indemnify and hold upon
allegations that the buyer, its agents, or employees have made additional warranties or
representations as to product preference or use.
(D) A fixed charge established for each product will be imposed for all equipment
returned for warranty repair and where the cause of failure cannot be identified by
Terrasat.
Note: Warranty seals are designed to break upon internal access. Access to the internal
electronic components without prior written approval will void the warranty.
For more information about returning a product for repair, see Repair Policy on
page 6-7.
Export Regulations
Under the Arms Export Control Act (AECA), 22 U.S.C. § 2778 (1994), the United
States Department of State, Directorate of Defense Trade Controls (DDTC),
implements the International Traffic In Arm Regulations (ITAR), 22 C.F.R.
§§ 120-130, which control the export of defense articles and services from the United
States to foreign destinations and persons.
Terrasat X-band IBUC products are subject to ITAR regulations administered by the
U.S. State Department. Section 121.1 of the ITAR is the United States Munitions List
(USML) and includes the commodities, related technical data, and defense services
controlled for export purposes. The X-band IBUC is classified as USML Category
XI(a)(5) “Command, control and communications systems to include radios
(transceivers), navigation, and identification equipment.” As indicated in the ITAR,
items in this category are also designated “Significant Military Equipment (SME).”
These products are not considered dual use as defined by the U.S. Commerce
Department.
As ITAR-controlled items that are designated SME, each license application must be
accompanied by Form DSP-83 identifying the end user and intermediate consignees.
Export Regulations | 1-5

In addition, Exporters must ascertain the specific end user and end use prior to
submitting a license application to the Directorate of Defense Trade Controls. Terrasat
normally requests a separate letter to accompany the DSP-83 stating the type of
terminal in which the IBUC will be used and the satellite system over which it will
transmit.
Further, it is required that we inform the end user of the requirements of ITAR section
123.9, as follows:
The written approval of the Directorate of Defense Trade Controls must be

obtained before reselling, transferring, transshipping, or disposing of a defense
article to any end user, end use, or destination other than as stated on the export
license.
Details of ITAR requirements can be found at the U.S. State Department Web site at 
http://www.pmddtc.state.gov.
1-6 | Introduction
C HAPTER
2
FUNCTIONAL DESCRIPTION
CHAPTER2
The Terrasat outdoor unit (ODU) consists of an intelligent block upconverter

(IBUC G) and power supply unit (PSUI) for use in satellite earth stations. The outdoor
equipment is designed to interface directly with an L-band satellite modem.
Introduction
This chapter contains detailed information about the various components of the
IBUC G system.
System Components
The interfacility link (IFL) between the ODUs and the L-band modem uses
950 MHz to 2.0 GHz (L-band) as the interface frequency. This approach enables
transmission and reception over the entire satellite band as opposed to a single
transponder. The L-band IFL can also carry associated signals such as 10 MHz or FSK
which simplify installation and reduce costs. Terrasat IBUC G systems can be used
for single channel per carrier/multiple channels per carrier (SCPC /MCPC),
point-to-point, or point-to-multiple point network applications (such as voice, data,
video, or IP services). The integrated RJ-45 J4 connector enables TelNet, SNMP, and
the embedded Web pages for monitor and control purposes.
The IBUC G uses a gallium nitride (GaN)-based power technology that makes it ideal
for high-power and high-frequency devices. The oversized chassis contains an
additional cooling fan assembly to protect the unit from high temperature operating
conditions.
For a typical equipment configuration, see Figure 2.3 on page 2-11.
The IBUC G is available in a variety of frequency bands as shown in Table 2.1 on

page 2-3. The IBUC G houses the IF interface (de-mux), the upconverter, the monitor
Introduction | 2-1
and control (M&C) card, an AC-to-DC converter, and a solid state power amplifier
(SSPA) assembly. The IBUC G can also house an optional internal 10 MHz reference
signal module. The input interface to the IBUC G connects to a 50 Ω or an optional
75 Ω coaxial cable that carries the L-band transmit signal, and can carry the external
10 MHz reference oscillator signal and bidirectional M&C FSK signals.
2-2 | IBUC G Functional Description

Table 2.1 IBUC G Transmit Frequency Plans
Signal Standard C-band X-band Standard Ku-band Full Ku-band
L-band 950 MHz to 1525 MHz 950 MHz to 1450 MHz 950 MHz to 1450 MHz 950 MHz to 1700 MHz
LO frequency 7.375 GHz 6.950 GHz 13.050 GHz 12.800 GHz
RF frequency 5.850 GHz to 6.425 GHz 7.900 GHz to 8.400 GHz 14.000 GHz to 14.500 GHz 13.750 GHz to 14.500 GHz
Output Power (PSAT) 400 watts 400 watts 150 watts 150 watts
System Components | 2-3

AC Supply
IBUC Gs operates on AC power at 200 VAC to 240 VAC.Figure 2.1 depicts the front
panel of an IBUC G.
Note: The IBUC G pictured in Figure 2.1 has an N-type connector at J1.
Mounting Hole
Breather Valve
Figure 2.1 Front Panel of an IBUC G
Fuses
Table 2.2 lists the the fuse markings of the fuses required by IBUC G models. As
reference, Table 2.3 on page 2-5 defines the international marking schema.
Table 2.2 Fuse Markings

Power
Signal Level Fuse Markings
C-band 400 W T12.5AH250V
X-band 400 W T12.5AH250V
Ku-band 150 W T10AH250V

Note: Terrasat recommends time lag fuses for the IBUC G.
Table 2.3 explains the fuse marking schema.
Table 2.3 Fuse Markings Explained

T10AH250V or T12.15AH250V
Speed Curent Rating Breaking Capacity Voltage Rating

10A = 10.0 Amp H = High Breaking Capacity
T = Time Delay 250V = 250 Volts
12.15A = 12.15 Amp (glass with sand filling)
Monitor and Control

The IBUC G is equipped with extensive monitor and control (M&C) capabilities. Use
any of the following methods to access those capabilities:
• Via the M&C 19-pin circular connector (J2) utilizing two-wire RS485. This
method requires that a separate cable must be run and connected to J2.
• Via the J2 connector using RS232. This method requires that a separate cable must
be run and connected to J2.
Figure G.1 on page G-2 contains a drawing for fabricating your own cable.
• Via the J4 connector using TCP/IP. This method requires a separate Ethernet
cable.
Figure G.2 on page G-3 contains a drawing for fabricating your own cable.
• Via the J2 connector by using an optional hand-held terminal. The hand-held
terminal has its own cable.
• Via the L-band input N-connector or F-connector (J1) utilizing frequency shift
keying (FSK). Using this method requires no additional cable(s) but does require
that the FSK be multiplexed onto the L-band cable.
Note: Some modem manufacturers offer built-in FSK capabilities for communicating with
the IBUC G through the L-band IFL. Refer to the modem manufacturer’s
documentation for more information.
RF Signal Flow
L-band input to the IBUC G is through the input N-connector or the F-connector
(labeled J1). Required inputs include an L-band signal at -20 dBm or less and a
10 MHz sine wave reference signal between +5 dBm and -12 dBm (for those units that
do not have the optional internal 10 MHz reference signal). The internal 10 MHz
reference signal meets the minimum phase noise requirements listed in Table 2.4.
Note: If an external 10 MHz reference signal is applied to a unit with the optional internal
10 MHz reference signal, the external signal has priority. When the external signal is

removed from such units, the system automatically reverts to the internal 10 MHz
signal, requiring no additional user input.
Table 2.4 Internal 10 MHz Reference Signal Parameters

Minimum Maximum Condition
-100 dBc/Hz 10 Hz
-130 dBc/Hz 100 Hz
Phase Noise
-140 dBc/Hz 1 kHz
-145 dBc/Hz 10 kHz
Frequency Stability vs. Operating
Temperature Range -100 ppb +100 ppb -40 °C to +85 °C
(referenced to frequency at +25 °C)
Tuning Range
±3 ppm ±10 ppm
(referenced to nominal frequency)
Tuning Slope Positive
AC power is applied to the IBUC G via the J3 connector and the 10 MHz, L-band, and
FSK signals via the J1 connector. The J1 inputs are routed to the demultiplexer
circuitry where the various signals are split off and routed to the appropriate circuits
within the IBUC G . The input voltage from the demultiplexer circuitry is routed to
the power supply and the FSK signal is routed to the M&C card.
The external 10 MHz reference signal is routed to the multiplier circuitry where its
level is first detected and an alarm issued if the signal is low. However, if the signal
level is low and the system is equipped with the optional internal 10 MHz signal, the
system will automatically switch to the internal 10 MHz signal. The 10 MHz signal is
then multiplied to the frequency used for phase-locking purposes. The output of the
multiplier is routed to the phase detector circuitry where it is compared with the phase
of the DRO (dielectric resonator oscillator) signal sample and consequently generates
a voltage that is applied as a control voltage to the DRO to adjust its frequency. The
DRO has been optimized for phase noise at a single frequency based on the frequency
band of that particular IBUC G. The output of the DRO is amplified and routed to the
mixer.
The L-band signal that is split off in the demultiplexer circuitry is first filtered and a
sample of it detected for input power detection and control purposes. The signal is
then amplified, and goes through a variable attenuator. The attenuation is used to
provide an attenuation adjustment of 30 dB in 0.1 dB steps and to provide automatic
level control (ALC) or automatic gain control (AGC).
After additional amplification and filtering, the signal is routed to the mixer. The
L-band signal is then mixed with the DRO signal to “upconvert” to the appropriate RF
signal based on the frequency band of the IBUC G. The RF signal is filtered,
amplified, and then routed to the temperature compensation circuitry. The temperature

compensation circuitry has been calibrated so that the IBUC G gain does not vary
more than 3 dB at any given frequency.
Note: Some units can vary up to 4 dB at any given frequency.
The signal is then routed through an isolator to the solid-state power amplifier (SSPA).
Some models have an additional mechanical filter between the isolator and the SSPA.
The SSPA amplifies the signal which is then routed to the output through an isolator
for reverse power protection. The RF output is detected for M&C purposes.
The IBUC G gain has been calibrated so that at minimum attenuation, the small signal
gain is, at a minimum, (PSAT + 31) dB. As an example, a 400 W C-band unit has a
minimum gain of 87 dB over frequency and over temperature.
To operate at lower power levels, reduce the input to the IBUC G or reduce the
IBUC G gain by using the variable attenuator, accessible using any of the M&C
interfaces. The output of a C-band IBUC G is a CPR137G waveguide or an N-type
connector, the output of an X-band IBUC G is a CPR112G waveguide and the output
of a Ku-band IBUC G is a WR75 cover with groove waveguide.
Figure 2.2 depicts the signal flow.

RS485
RS232
HHT
J2
Monitor and Control (M&C)
Alarm
Switch Control
J4
TCP/IP
AC/DC
VAC Power Supply All Circuits
J3
FAN
Internal
M&C 10 MHz
M&C M&C
FSK M&C
PL DRO
Detector
De-Mux
External Detector Multiplier

10 MHz
RF OUT
M&C Coupler
M&C M&C SSPA
M&C
FSK Temp
J1
External 10 MHz Comp

Detector Gain Adjust ALC/AGC Monitor/
J5
L-band
Test Port
Figure 2.2 IBUC G Block Diagram

Software
The IBUC G monitors and controls numerous parameters and has features which
simplify installation and use and enhance system performance.
Some of these key features include:
• Monitor and Control

The IBUC G can be monitored and controlled through an assortment of interfaces
including RS232, RS485, Ethernet port, an optional hand-held terminal, or via an
FSK link with compatible modems. The FSK link is multiplexed on the L-band
IFL thus eliminating the need for an additional cable and simplifying installation.
For a full description of these functions, see Chapter 5, Monitor and Control
Features.
• Tx Attenuation
The gain of the unit can be set over a 30 dB range in 0.1 dB steps.
• Automatic Gain Control (AGC)
The IBUC G continuously monitors input and output levels. When AGC is
enabled, the gain of the system is maintained at a constant level by an internal
algorithm. Gain is the difference between output power and input power.
• Automatic Level Control (ALC)
Similar to the AGC system, when ALC is enabled, the gain is adjusted to maintain
a constant output level.
• Redundancy
The IBUC G automatically senses when configured as a redundant system. This
logic is built-in—eliminating the need for an external switching controller.
• Embedded Web Pages
Provides management for small networks by using a Web browser.
• Simple Network Management Protocol (SNMP)
Provides integration of IP M&C in existing network management systems.
• Burst Operation
Enables operation in burst mode. The IBUC G reports average output power of
valid bursts (above a burst threshold) when in burst mode.
• Alarm History (with time stamps)
A log of alarms that occur is maintained. This can simplify troubleshooting of the
system (especially when an intermittent problem occurs).

• Sensors
A series of internal sensors enable you to verify performance and to troubleshoot
the system. Sensors include internal temperature, 10 MHz input detector, supply
voltage, current consumption, phase-locked dielectric resonator oscillator
(PLDRO) lock voltage, input level and output level.
System Configurations
Figure 2.3 shows a typical earth station installation using Terrasat block upconverters.
In normal operation, the IBUC G is mounted outdoors. The IBUC G can interface
directly with a satellite modem, a 70 MHz to L-band rack converter, a modem
combiner network, or an interface unit (IFU). Table 2.5 lists the requirements for
proper operation.
Table 2.5 Basic System Requirements
IBUC G
AC supply
~AC mains
10 MHz reference signal
~internally referenced
~externally referenced
L-band signal
Certain considerations must be made when selecting the IFL because appropriate
shielding and signal levels are required for normal system operation. The IBUC G
provides a variable attenuator that is accessible through the various M&C interfaces
that enables the gain of the unit to be reduced by up to 30 dB in 0.1 dB steps. The
attenuator can be used to prevent overdrive to the IBUC G in configurations with a
short cable run (or IFL), thus preserving the dynamic range of the modem. In addition,
the externally referenced IBUC G must have a 10 MHz input signal at +5 dBm
to -12 dBm for the IBUC G. The maximum voltage drop for an IBUC Gs is 200 VAC
to 240 VAC.
Note: The system configuration in Figure 2.3 depicts an external 10 MHz reference signal;
however, an optional internal 10 MHz reference signal is available.

LNB
Hand-Held 
nd
L-ba → Terminal
← Rx z and VDC 485
→
10 M H r RS
32 o
RS 2
←
K→ →
← FS MH z
n d / 10
a
T x L-b
O D EM G
LITE M U C
S A TE L IB
t→
e rne
Eth
←
200-240 VAC
INDOOR EQUIPMENT OUTDOOR EQUIPMENT
Figure 2.3 IBUC G System Configuration

Storage Information
There are no storage limitations on the IBUC G or redundant (1+1) interfaces for
redundant systems other than avoiding excessive exposure beyond the -45 °C to
+65 °C external ambient temperature.

C HAPTER
3
INSTALLATION
CHAPTER 3
This chapter contains the general requirements for installing the Terrasat IBUC G.
Introduction
The IBUC G consists of an intelligent block upconverter and a solid-state power
amplifier (SSPA). An indoor interface unit (IFU) can also be part of the configuration.
General Requirements
WARNING
For protection of personnel and equipment,
use care when installing the antenna and
whenever working on or around the
system.
Follow standard safety precautions with

hand or power tools.
Use care in working with high AC voltages

and microwave emissions.
Unpacking
Check to make sure that the ODU has not been damaged in shipment. If there is any
damage, contact the shipper before proceeding. If you need to declare any equipment
as damaged during transit, save the original shipping cartons to ease inspection
reporting.
Terrasat recommends retaining and re-using all shipping cartons and foam forms if the
equipment will be stored or reshipped. The cartons should be clearly marked to
indicate that they contain fragile electronic equipment.
Compare the contents of the shipping container with the packing list to ensure that all
items have been received. If any item is missing, contact Terrasat.
Furnished Items
The following items are furnished with Terrasat Communications, Inc. IBUC Gs:
• An IBUC G with an integrated solid state power amplifier (SSPA)

• Product documentation on CD
• Waveguide gaskets and hardware (waveguide units only)
• Test datasheet
• AC supply mating connector
Figure G.4 on page G-5 contains information about fabricating your own AC
supply cable
• Sealing tape for Type-N connector
• 5 g pouch of Permatex anti-seize lubricant
The anti-sieze lubricant is a heavy duty high-temperature lubricant that prevents
galling (friction between metal parts that can weld the nut and bolt together and
prevent removal), seizing, and corrosion of fasteners during assembly and aids the
disassembly of parts exposed to heat or corrosive environments.
• Fuses
• 19-pin monitor and control (M&C) mating connector (optional)
• IP67 industrial RJ45 mating connector (optional)
• Mounting brackets and bolts (optional)
3-2 | IBUC G Installation

Figure 3.1 illustrates the contents of the shipping carton of an IBUC G as it leaves the
factory.
M&C Mating Documentation CD

Connector
IBUC G
Permatex
Lubricant
Assorted
Hardware
Installation Drawing
Sealing Tape
Figure 3.1 Contents of an IBUC G Shipping Carton
Accessories
The following are optional accessories:
• A 9 A AC power line filter

• A hand-held terminal and cable
• A waveguide Rx reject filter
• A four-way combiner/divider module
• A TCP/IP test cable
• Waveguide pieces
• IFL cables (for example, LMR-400)
• Installation kits
Note: Exact contents of the shipping carton vary according to the model and type of
IBUC G.
General Requirements | 3-3

Installing the ODU
Consider the following when preparing to install the ODU.
Tools
Have available a standard electrician’s toolkit and any tools listed in the antenna
manufacturer’s installation instructions.
Test Equipment
Terrasat recommends the equipment or its equivalent listed in Table 3.1 for
installation and system alignment.
Table 3.1 Recommended Test Equipment

Equipment Type
Spectrum Analyzer Agilent HP8563E
Digital Voltmeter Fluke 8050
Cross coupler Used with all bands
RF cables With calibrated insertion loss up to 15 GHz
Waveguide High-power Termination High power to match HPA output
Assortment of cables, connectors and adapters
(calibrated up to 15 GHz)
Site Considerations
The ODU is designed to be mounted on or near the antenna. Locate and install the
antenna according to instructions supplied by the antenna manufacturer. Choose an
area that is free of interference from motors or other electrical equipment and that has
a clear line of sight from the antenna to the satellite. Use size 3/0 or 4/0 AWG
(American Wire Gauge) stranded copper wire to ground the IBUC G to the antenna
frame and to the lightning protection ground rod. For higher power units with an
external power supply, Terrasat recommends using an isolation filter to reduce power
line interference.
Mounting Considerations
Optional mounting brackets are available to aid mounting on most antennas.
The ODU must be mounted such that:
• The IBUC G has sufficient support to minimize the effects of antenna sway in
strong winds.
• The fan intake and exhausts are free from any obstructions.
• The heat fins have air movement across them.

Throughout installation and during any polarization, azimuth or elevation adjustment,
ensure that cables and waveguide are not crimped or pinched. Ensure that there is
adequate slack in the cable.
Power Requirements
WARNING
Installation and connection to the line
power supply must be made in compliance
with applicable wiring codes and
regulations.
Outdoor Power Supply

IBUC Gs do not require an external power supply. IBUC Gs are powered by
200 VAC to 240 VAC.
All IBUC Gs are furnished with a detachable AC power connector that is used to
connect and disconnect power. When connecting the AC connector to the AC power
source, the wiring must include a 15 amp or 20 amp circuit breaker. A disconnect
device (such as a circuit breaker or mains supply plug on the power supply cord) that
is readily accessible must also be provided. Any outdoor AC connections should be
made using suitable connectors or boxes with an IEC protection class of at least IP65.
WARNING
Ensure AC power is off when connecting or
disconnecting the power cord. To turn off
AC power to the unit, use the installed
circuit breaker or a similar disconnecting
device.
If a circuit breaker is not easily accessible as a disconnecting device, the input

connector will be the disconnecting device. In this case, the socket-outlet must be
installed near the equipment and must be easily accessible for pluggable equipment.
All IBUC Gs are furnished with mating connectors for the AC mains power cable. To
remain compliant with European Low Voltage Directive (EN 60950-1), use a power
cable that meets IEC 60227 requirements such as HAR Cable Designation H03VV-F
or H03VVH2-F and/or others with water resistance for outdoor applications. Power

cable plugs must also comply with all applicable local and federal standards and
regulations.
Note: AC transients and surges can cause data transmission errors and loss of
synchronization in the modem and/or the ODU. Take proper precautions to ensure
uninterrupted service.
Grounding
Terrasat recommends the following grounding and lightning protection:
• Cable Shielding
Shield currents can be eliminated with proper techniques. A grounding strap at the
end of the coaxial and data cables should be connected to the ground lug at the
antenna base with #4 gauge copper wire. This provides a path of least resistance
prior to entering the equipment.
• AC
The best way to protect the equipment is to have two protectors. The first is the
power mains protector that is mounted directly across the mains in the breaker
box. The second should be mounted or grounded directly at the base or hub of the
antenna or at the 19-in. rack.
• Data and Control Lines
The I/O lines can deliver surge current to the equipment and should also be
protected.
• Electrical Grounding
Grounding of the IBUC G is recommended to prevent possible damage from
lightning or other induced electrical surges. Terrasat recommends using 3/0 or 4/0
AWG stranded copper wire for bonding the IBUC G to the earth ground (or
grounding rod), using the most direct or shortest route.
Antenna Recommendations
Most antenna masts are encased in concrete. Typically, the mast pipe is submerged in
a 4 ft to 5 ft (1.22 m to 1.53 m) deep augered hole. This provides a good Ufer ground.
A Ufer ground encases grounding connectors in concrete. Concrete absorbs moisture
quickly and loses that moisture slowly—as much 15 to 30 days after rain or snow
melt). The mineral properties of concrete and their natural pH mean that concrete has a
supply of ions to conduct current. The soil around concrete becomes “doped” by the
concrete and, as a result, the pH of the soil rises. The moisture in the concrete in
combination with the “doped” soil make a good connector of electrical energy. The
concrete’s large volume and area of contact with the surrounding soil allow a good
transfer to the ground. In the concrete base, a Ufer ground can be established by
running #4 gauge solid wire or rebar and connecting to the base of the pedestal with
pigtails.

The Ufer ground is only one step in proper grounding. The Ufer ground should be
augmented with coupled pairs of 10 ft (3.05 m) ground rods placed 20 ft (6.1 m) into
the ground, spaced 20 ft (6.1 m) apart. The first rod should be placed close to the
antenna. The second rod should be placed towards the equipment enclosure. A #2
gauge wire should connect the rods and antenna mount. A ground rod should be placed
at the equipment enclosure, as well. If it is virtually impossible to install the ground
rods, then radials are needed. This can be accomplished by laying 10 or more lengths
of 1½-in. (3.81 cm) copper strap at least 50 ft (15.24 m) long in a radial fashion around
the antenna base. The straps should be buried, if possible. The hub must be
interconnected to the utility ground.
The ground configuration can vary from one location to another. It is best to measure
soil conductivity and design a 5 Ω or less ground system. To protect the system from a
direct strike, a lightning rod placed 2 ft (61 cm) higher than the highest point of the
dish should be interconnected to the Ufer ground with #2 gauge copper wire.
Antenna Mounting
The IBUC G has a variety of mounting options: on the focal point, the boom arm, the
antenna back structure, or in the hub (depending on the antenna type).
The IBUC G has mounting holes on both sides of the unit that can be used to attach
the IBUC G to the antenna. For the location of these mounting holes, see Figure 3.2.
Mounting
Holes
Figure 3.2 Location of Mounting Holes of an IBUC G
There is also a single mounting hole located on the front of the IBUC G that is
identified in Figure 2.1 on page 2-4. This mounting hole is on the same axis as the
center of the waveguide of the unit (that is, it is in line with the center of the

waveguide). This single mounting hole enables the unit to be rotated when mounted
on the focal point of an antenna.
Optional mounting brackets are available that aid in attachment to antennas. The
mounting slots identified in Figure 3.3 on page 3-8 give you additional flexibility
when attaching the IBUC G to the antenna.
Note: Ensure that the threads of the bolts used for mounting the IBUC G have been dipped
in the included Permatex anti-sieze lubricant. This prevents galling, seizing, and
corrosion of fasteners during assembly and will aid in future disassembly. For more
information about applying the Permatex lubricant, see page 3-12.
Mounting Bracket
Adjustment Slots
Figure 3.3 Location of Adjustment Slots on Optional Mounting Bracket
System Pressurization
The IBUC G chassis contains a breather valve (its location is identified in Figure 2.1
on page 2-4) that is designed to equalize pressure inside and outside of the unit while
allowing the passage of air or water vapor but not environmental contaminants such as
liquids, debris, or dust. If you intend to pressurize the waveguide, you must install a
pressure window at the output of the IBUC G, otherwise the breather valve will not
permit pressurization of the system.

System Cabling Requirements
Cables and Connectors

IBUC G interface connectors and their mates are listed in Table 3.2. Additional
mating connectors and/or cables can be ordered from Terrasat at optional items.
Table 3.2 IBUC G Interface Connector Schedule

REFERENCE INTERFACE INTERFACE
DESIGNATOR FUNCTION CONNECTOR CONNECTOR MATE
TYPE-N SOCKET TYPE-N PLUG
J1 Tx Input
(TYPE-F SOCKET optional) (TYPE-F PLUG optional)
AMPHENOL CIRCULAR, BOX AMPHENOL CIRCULAR, STRAIGHT
J2 M&C Interface MOUNTING SOCKET, 19S PLUG, 19P
(PT02E-14-19S (027)) (PT06E-14-19P (475))
CONNECTOR, MALE CONNECTOR, FEMALE 
J3 AC Power RECEPTACLE, 3+PE PLUG, 3+PE
(AMPHENOL C016 20C003 100 12) (AMPHENOL C106 20D003 110 12)
RJ45-IP67 SHIELDED INLINE
J4 Ethernet RJ45-IP67 PLUG
CONNECTOR WITH CAP
J5 Monitor Port TYPE-N SOCKET TYPE-N PLUG
CPR137, CPRG WAVEGUIDE OR CPR137, CPRF WAVEGUIDE OR
RF OUTPUT C-band
TYPE-N SOCKET TYPE-N PLUG
RF OUTPUT X-band CPR112, CPRG WAVEGUIDE CPR112, CPRF WAVEGUIDE
WR75 COVER FLANGE WITH
RF OUTPUT Ku-band WR75 COVER FLANGE
GROOVE
J1 – Transmit In The Tx Input connector is a Type-N socket (Type-F socket,

optional) connector used to connect the IF at L-band from the modem to the IBUC G.
Use 50 Ω cables (75 Ω for Type-F connectors) to connect to J1. Certain considerations
must be taken when selecting the IFL because appropriate shielding and signal levels
are required for normal system operation. The IBUC G is designed to operate at rated
power with a –30 dBm Tx L-band signal, with the variable attenuator set to minimum
attenuation. The variable attenuator is accessible through the M&C interfaces for
system gain adjustment. In addition, the IBUC G must have a 10 MHz input signal
from +5 dBm to –12 dBm (only for IBUC Gs with an external 10 MHz reference
signal). For IBUC Gs with both the optional internal reference signal and an external
10 MHz signal, the external signal will automatically receive priority without any user
interaction.
Note: Some modems provide an FSK communication link for M&C purposes via the same
interface (J1).
Fire codes may require that cables in occupied building be installed in steel conduit.
Local government agencies may waive this requirement with the use of Plenum cables
which are standard cables encased in solid Teflon. Check codes for your area.

Note: Equipment outages due to faulty installation are not covered by the Terrasat warranty.
Terrasat recommends following OEM procedures when making cables and
connectors.
J2 – M&C Interface The M&C interface is a 19-pin circular socket connector used to
enable remote monitoring and control of IBUC G operating parameters. Pin
assignments are shown in Table 3.3. If the M&C port of the IBUC G is going to be
used, the cable should be a shielded multiconductor cable. For more information about
fabricating your own cable, see the IP cable drawing in Appendix G. An optional
pre-assembled IP test cable is available from Terrasat.
Table 3.3 Pin Assignments for IBUC G M&C Connector J2

PIN FUNCTION
A RS485 (+)
B RS485 (–)
C Hand-held Terminal Power (+)
D RS232 RXD
E RS232 TXD
F HHT, RS232, RS485 Common
G Alarm Output
H Not used
J Not used
K Not used
L IBUC G Alarm Output Normally Open
M IBUC G Alarm Output Common
N IBUC G Alarm Input / Mute
P IBUC G Output Normally Closed
R 1+1 Switch Command A
S 1+1 Switch Command B
T 1+1 Switch Indicator A
U 1+1 Switch Indicator B
V 1+1 Redundancy Enable
Note: Pin F is the return to close the circuit for RS232.

J3 – AC Power AC Power is supplied to the IBUC G through a 3-pin plus ground
connector. The connector is configured as described in Table 3.4.
Table 3.4 Pin Assignments for IBUC G AC Power Connector J3

PIN FUNCTION
1 N/C
2 Neutral
3 Line
GND Ground
J4 – Industrial Ethernet Connector The industrial Ethernet connector is an

IP67-rated RJ46 Cat. 5e interface with a locking protective cover. The connector is
configured as described in Table 3.5.
Table 3.5 Pin Assignments for IBUC G Ethernet Connector J4

PIN FUNCTION
1 Tx (+)
2 Tx (–)
3 Rx (+)
4 Not Used
5 Not Used
6 Rx (–)
7 Not Used
8 Not Used
RF Output The types of waveguide used for various bands of the IBUC G are listed
in Table 3.2 on page 3-9.
Cable and Waveguide Connections
WARNING
Ensure that all power is disconnected prior
to making any connections.

When installing the cable and waveguide assemblies, ensure that all connections are
weather tight. If an Rx reject filter is being used, attach it to the IBUC G waveguide
output. Use proper gasketing methods to prevent the entry of water.
Water-Resistant Wrap
Terrasat recommends applying water-resistant wrap (such as mastic tape) to all
outdoor connectors to prevent the entry of water and subsequent water damage. Mastic
tapes are designed to flow and self-heal if cut or punctured. When applied spirally
with the proper tension, mastic tapes form a tight continuous coating that permits little
or no moisture absorption or penetration. Terrasat provides water-resistant sealing
tape for Type-F and Type-N connectors.
Apply the mastic tape, as follows:
1. Ensure that all connectors are firmly tightened, dry, and free from all grease, dust,
and dirt.
2. Cut the mastic tape to the desired size. The tape should be long enough to cover
the connector completely.
3. Center the tape on the connector to be sealed and wrap the tape in a tight spiral
around the connector using a 50% overlap. Squeeze the tape tightly and ensure that
both ends of the tape have formed around the connector and the cable with any
gaps.
Apply the tape to all connectors that may be exposed to moisture.
Applying the Anti-Sieze Lubricant

Terrasat recommends applying anti-sieze lubricant to screws and bolts that could be
exposed to weathering or corrosive environments. The lubricant prevents galling,
seizing, and corrosion during assembly and aids in future disassembly. A 5 g pouch of
Permatex anti-seize lubricant is included with the installation kit for this purpose.
To apply the anti-seize lubricant,
1. Wear appropriate person protection equipment to avoid contact with skin and eyes.
This includes safety glasses, neoprene or nitrile gloves, and clothing sufficient to
limit skin exposure.
2. Ensure that mating surfaces (screw holes) are clean, dry and free of dirt, debris, or
loose surface rust.
3. Use a brush or lint-free cloth to apply a think coat of anti-seize to the screws and
bolts that require protection, as shown in Figure 3.4. The anti-seize should be
applied right down to the base of the threads.

Figure 3.4 Applying the Anti-Seize Lubricant
4. Spread the lubricant to a thin film without any lumps.

5. Reassemble the parts using normal torque values.
6. Wipe off any excess material with a disposable towel.
Waveguide Connections
If necessary, connect a section of flexible waveguide between the orthogonal mode
transducer (OMT) transmit port and the IBUC G Tx RF output (or optional Rx reject
filter). The waveguide should be attached to the antenna feed according to the
manufacturer’s instructions. Use proper gasketing methods to prevent water entry and
subsequent damage.
Note: During installation, be sure to remove the sticker shown in Figure 3.5 that covers the
waveguide flange. The sticker itself does not create a pressure window and will allow
moisture to enter the waveguide. Also be sure to install the waveguide gasket into the
channel identified in Figure 3.5 to ensure a good seal between surfaces. Do not re-use
old gaskets.

Channel for
Waveguide Gasket
Figure 3.5 Waveguide Label and Channel for Gasket
WARNING
The output of the IBUC G is microwave
power. Never look into the waveguide or
put your head into the path of the beam that
goes to the satellite.
Typical Configuration With an IBUC G But Without an IFU

Figure 2.3 on page 2-11 illustrates a typical configuration for IBUC Gs.
To configure an IBUC G:
1. Connect the IFL coaxial cable between the Tx output from the modem and the Tx
input connector J1 of the IBUC G.
2. Connect the M&C cable between the M&C port on the IBUC G and the
appropriate M&C or LAN connection.
Note: Use the J2 port if you are using RS232, RS485, or a Form-C relay for monitor and
control purposes.
Use the J4 port if you are using Ethernet for monitor and control purposes.
3. Connect the AC cable between the AC input connector J3 on the IBUC G and the
AC power source.

Basic System Alignment
The following sections outline the procedure for setup and alignment of an earth
station. Before you align the ODU, the antenna should be set to the desired azimuth
and elevation settings per the manufacturer’s instructions.
Ensure that the IBUC G Tx output power is disabled to prevent accidental

transmission interference with adjacent satellite or transponders before attempting to
align or perform any other operation involving the ODU. Before attempting any signal
changes, carefully evaluate the possible effects of the transmitted signal.
CAUTION
The IBUC G must not transmit until
alignment and any necessary adjustments
are complete.
Setting the Tx and Rx Frequencies

All transmit and receive frequencies are set in the modem.
If using a direct connection to an L-band modem, follow the manufacturer’s

instructions for setting the transmit and receive frequencies.
Transmit Power Alignment
Transmit L-band Input Adjustment with Modem or Converter

1. Use a spectrum analyzer to measure the power level of the L-band signal at the
output of the coaxial cable that connects to the IBUC G at the Tx L-band connec-
tor J1.
2. Check that the 10 MHz reference signal is present and within the range of +5 dBm
though –12 dBm.
Note: The IBUC G requries a 10 Mhz reference signal to operate. Check the model
number of your IBUC G to determine whether an external 10 MHz signal is
required.
3. Use the level adjust mechanism of the modem or converter to increase or decrease
the power level to the desired output.
4. Disconnect the spectrum analyzer from the coaxial cable.

Transmit RF Output Adjustment with Modem or Converter (70 MHz to
L-band)
To adjust the power level of the IBUC G transmitter output,
1. Connect a cross coupler and a high-power termination to the IBUC G waveguide

output.
2. Ensure that power to the IBUC G is applied in the proper voltage range.
3. Connect the Tx L-band input signal to the Tx L-band connector J1 on the IBUC G.
4. Enable the Tx signals in the modem or converter and the IBUC G. Ensure that
ouput power levels are low at first and then gradually increase the power level.
5. Measure the RF output with a power meter connected to the cross coupler attached
at the waveguide output. For accuracy, measure pure carrier (that is, continuous
wave or CW) and the frequency allotted to you by the satellite network operations
center (NOC).
6. If the modem still has available range, use the level adjust mechanism to reach the
designated power level. If there is no available range, use the attenuation setting
on the IBUC G instead.
Note: To set attenuation on the IBUC G, you first need to establish communication with
the IBUC G. For more information about the various M&C interfaces you can use
to establish communication, see Chapter 5, Monitor and Control Features.
7. If using a satellite modem, adjust the RF output to the designated power level
(provided by the satellite network operations center or its engineering staff) with
the L-band output (modem) level adjust mechanism.
8. Disable the Tx signal in the modem or converter.
9. Disconnect the Tx L-band input signal.
10. Remove the cross coupler and termination, and then install the transmit waveguide
section to the antenna transmit feed.
11. Once the transmit input and output power levels have been set, begin transmitting
by connecting the Tx L-band input signal to the J1 connector on the IBUC G and
enabling the Tx in the modem or converter.
12. Under the guidance of NOC staff, fine-adjust the transmit power for the desired
down link margin at the receiving station by adjusting the Tx L-band output level
adjust (modem or converter output) or by adjusting the gain of the IBUC G by
setting the Tx attenuator.

Final Checks
To ensure reliable operation, inspect the system for crimped or pinched cabling. Make
sure that all connections are secure and sealed. Once the system has been aligned and
is operating satisfactorily, the IBUC G will require infrequent maintenance.
Final Checks | 3-17


C HAPTER
4
OPERATIONS
CHAPTER 4
This chapter describes general operation of the IBUC G.
Introduction
After the IBUC G has been mounted and connections verified, the antenna must be
aimed towards the appropriate satellite. Follow the antenna manufacturer’s
instructions, using the coordinates (azimuth, elevation, and polarity) provided by the
satellite operator. Do not transmit until you have received authorization—including a
transmit power level—from the satellite network operations center (NOC) staff.
Start-up Checklist
The IBUC G leaves the factory preconfigured for operation; however, you can
fine-tune its settings for your particular needs.
Prior to start up, verify the following:
• Transmit/Receive frequencies
All transmit and receive frequencies are set using the modem. Follow the modem
manufacturer’s instruction.
• Cable connections
Ensure that all of the external cables between the IBUC G and other equipment are
seated correctly and that there are no breaks or cracks, no sharp bends, pinch
points nor flattened sections in the cables.
• Power
Ensure that the IBUC G is receiving power. Power comes via AC mains.
Introduction | 4-1
• 10 MHz reference signal
Verify that the 10 MHz reference signal is present. Some IBUC Gs have an
internal 10 MHz reference signal. If this option is not available, a 10 MHz
reference signal supplied on the IF cable from the modem (or an IFU) is required.
Turning On the IBUC G

To turn on the IBUC G,
1. Connect the L-band input cable (J1), the M&C cable (J4), and the power cable (J3)
2. Apply power to the IBUC G.
3. The Power LED on the side of the unit next to the J4 connector lights up.
A flashing green light indicates that the IBUC G is operating normally.
A red light indicates only that a fault (or alarm) has occurred. (A flashing red light
indicates a minor alarm and a solid red light indicates a major alarm.)
4. Allow the unit to warm up for approximately 15 minutes before operating the
transmitter module. This will assure stable gain and power.
Setting Operating Parameters

To set operating parameters, the IBUC G must be connected to a terminal (for
example, a hand-held terminal, a terminal emulator such as HyperTerminal, or the
embedded Web pages via a PC). The most user-friendly way to connect to the
IBUC G is by using the embedded Web pages. Connect the IBUC G to the Ethernet
port of a PC by using a TCP/IP cable assembly (such as the one depicted in Figure G.2
on page G-3).
1. Establish communication with the IBUC G by using the steps provided in

Appendix C, IBUC G Web Pages.
2. Navigate to the Transmit Configuration tab as shown on page C-14.
3. Set the Tx Output by selecting whether the unit is actively transmitting or not.
Options include:
• Enable
• Disable
When the Tx Output is set to Disabled, the Tx Output level displayed on the Sensor
Tab (shown on page C-12) reads -99.0 dBm. This is not the actual reading.
When conditions cause the automatic shut-off of the Tx Output signal, the Tx
Output is muted and the Tx Output level displayed on the Sensor Tab (shown on
page C-12) reads -96.0 dBm. This is not the actual reading.
4-2 | IBUC G Operations

Note: This setting can be overridden by the modem. The modem will send commands
(data) to the IBUC G and no single port is given priority. This continues as long as
both the IBUC G and the modem use Legacy Binary mode. If the IBUC G is set to
ASCII mode, communication between the modem and the IBUC G stops due to
the differences in command formats.
4. Set the Power Monitor Frequency that is used to set at which frequency you are
operating. The factory default values in Table C.1 on page C-15 are listed
according to the model number of the IBUC G.
Note: To ensure accurate readings, you must set the actual operating frequency.
Example: If, according to your Satellite NOC, your allocated frequency is
6400 MHz, set the Power Monitor Frequency to 6400 MHz. Do not use the factory
default value unless that is your actual operating frequency.
5. Set the Power Read Mode.
Options include:
• Burst
• Continuous Wave
6. Set the Gain Mode.
Options include:
• Open
Open is the gain obtained when there is no feedback in the measuring loop.
• AGC (Automatic Gain Control)
The IBUC G continuously monitors input and output levels. When AGC is
enabled, the gain of the system is maintained at a constant level by an internal
algorithm. Gain is the difference between output power and input power.
• ALC (Automatic Level Control)
Similar to the AGC system, when ALC is enabled the gain is adjusted when
changes are detected in order to maintain a constant output level.
Note: The IBUC G has an internal temperature compensation feature that minimizes gain
variations due to to changes in temperature. This feature is configured at the factory
and requires no user input. For specific information about your particular model
IBUC G, see the datasheets in Appendix G, Component Specifications and
Reference Drawings.
Start-up Checklist | 4-3

Setting the Tx Frequency (L-band)
Changing the L-band frequency will cause a change to the RF frequency.
To set the L-band frequency,
1. Establish communication with the IBUC G by using the steps provided in

2. Navigate to the Information tab as shown on page C-6.
3. Verify the data in the Band Inversion field.
4. Calculate the IF frequency by using the following formulas:
IF = RF - LO Non-inverted/Low side
IF = LO - RF Inverted/High side
Note: RF and LO frequencies for various bands are provided in Table 2.1 on page 2-3.
Setting Alarm Thresholds

Although the IBUC G will function using the factory-configured settings, by setting
high and low level thresholds for the Tx Input/Output you can access more
information about events such as power fluctuations that might trigger an alarm.
Alarms will be generated when the input and output amplitudes fall outside of the
threshold ranges. For this reason, Terrasat recommends that when you have reached
the proper input and output settings for your budget, you narrow the threshold ranges
for alarms.
1. Set the Tx Input High/Low Thresholds.

The IBUC G leaves the factory with a default range of -15 dBm to -60 dBm.
Example: After observing the unit, you determine that the IBUC G operates
consistently at -37 dBm. Although the threshold range is 45 dB, that range is too
wide for everyday use. Instead consider setting the input thresholds at ±3 dB; this
would make the high level threshold -34 dBm and the low level threshold -40 dBm.
Note: You will receive an error message if the input level exceeds the threshold range.
2. Set the Tx Output High/Low Thresholds.
When you set up your system and the Tx Output reaches its budgeted level, Terrasat
recommends that, instead of the (PSAT - 20 dB) to (PSAT + 1 dB) threshold range
that is the default, you narrow the range between the high and low thresholds to
±3 dB.
Example: After observing the unit, you determine that the output level operates
consistently at 32 dBm. Although the threshold range is 21 dB, that range is too
wide for everyday use. Instead consider setting the output thresholds at ±3 dB; this

would make the high level threshold 35 dBm and the low level threshold 29 dBm.
Note: You will receive an error message if the output level exceeds the threshold range.
3. Verify your settings against the readings on the Info Page as shown on page C-6 of
Configuring Alarm States

The IBUC G offers flexibility with the levels of alarms produced when user-specified
thresholds are exceeded.
1. Consider which alarms to configure. Table 5.1 on page 5-4 contains the default
alarm configuration.
2. Navigate to the Alarm Configuration tab shown on page C-24 of Appendix C,
IBUC G Web Pages.
3. Use the drop-down menus to mark an alarm as a major event, a minor event, or to
disable it.
4. Click Save Settings when you have completed your inputs to ensure that your
settings are saved. If you do not click Save Settings, your changes will not be
implemented.
Configuring ALC/AGC
The IBUC G offers two methods of ensuring consistent signal levels: automatic level
control (ALC) and automatic gain control (AGC).
ALC
When enabled, the Automatic Level Control (ALC) circuitry in the IBUC G monitors
output levels and adjusts the gain to maintain a consistent output for input signal
variations. If a signal level is consistently below the predetermined target level, the
ALC will cause the gain to be increased until the target level is reached. If a signal
level exceeds the target level, the ALC will decrease the gain.
To enable ALC,
1. With the Gain Mode set to “Open” and the Tx Input and Tx Output Thresholds set,
monitor the Tx Output level in order to determine a baseline setting.
2. When the Tx Output Level reading is equal to the level that you want to maintain,
enable ALC by using any of the M&C interfaces.
The IBUC G will now continuously self-monitor, increasing or decreasing the gain in
order to maintain a constant signal at the level you defined.
Note: The Tx Output Level is “captured” when ALC is enabled.
Start-up Checklist | 4-5

AGC
When enabled, the Automatic Gain Control (AGC) circuitry in the IBUC G maintains
the gain constant and equal to the target gain that was established when AGC was
enabled.
Gain control settings can drift with time or temperature changes. You can reset the
Gain Control function (when reset, the Gain Control returns to mid-range or 0.0).
Terrasat units enable you to offset the target by using the attenuation control without
having to first disable the ALC or AGC.
Example: Set the output power level to 40 dBm and enable ALC. From this point
forward, the ALC algorithm will maintain the output level at 40 dBm.
If you want to change the output level to 41 dBm, reduce the attenuation by 1 dB. The
target level will be updated automatically.
Configuring the External Mute

Pin N of the M&C interface connector has dual functionality: it functions as an alarm
input or an external mute.
External Mute
When the IBUC G operates as a single thread IBUC G, Pin N of the M&C interface
connector functions as an external mute. If it is not connected (left open), then
transmission is not muted. When Pin N is connected to Pin F (chassis ground),
transmission is muted.
To re-enable transmission, remove the Pin N connection to Pin F. Transmission will

now resume.
Alarm Input
When the unit is operating as part of a redundant IBUC G system, the redundant
configuration is sensed automatically. In redundant systems, Pin N functions as an
alarm input where the alarm output of the A: side IBUC G is connected to the alarm
input of the B: side IBUC G and vice versa.
For more information about the M&C interface connector, see System Cabling
Requirements on page 3-9.

Common Errors
LED is Red
A red LED indicates only that a fault (or alarm) has occurred and does not necessarily
indicate that transmission has stopped. A flashing red light indicates a minor alarm and
a solid red light indicates a major alarm. You can communicate with the IBUC G to
determine what is causing the fault, and then clear the fault condition.
1. Establish a connection with the IBUC G by using any of the M&C interfaces
described in Chapter 5.
2. View the Alarm Status Tab (shown on page C-8) to determine the current alarm.
You can also check the Sensor Tab (shown on page C-12) to determine which
reading caused the alarm, and then compare the readings with the threshold levels.
If necessary, adjust the threshold level(s).
When the fault is cleared, the LED should be flashing green.
No Power to the IBUC G

If the Power LED is off or not turning on at all, the IBUC G is probably not receiving
power.
Restore power to the IBUC G by
• Checking that all cable connections are solid.

• Checking that the power supply is functioning or that AC mains has the proper
voltage.
• Checking the disconnect devices such as the circuit breaker.
• Checking the fuses.
Note: Fuses are 5x20 mm time-lag glass body cartridge type.
WARNING
Before applying power to the unit, ensure
that that waveguide output is properly
terminated. Failure to do so could lead to
serious personal injury, excessive RF
radiation levels, and equipment damage .
Common Errors | 4-7

Time Stamp Data is Incorrect
The time stamp on the alarm log is incorrect after the IBUC G has lost power for an
extended period. You can set the system date and time by using the hand-held terminal
(see Appendix D) or the System Configuration tab of the embedded Web pages (see
Appendix C).
When using a Web browser to access the embedded Web pages, the time stamp
information displayed differs slightly by Web browser. The time stamp displayed on
the Web pages records the time that the page was created and is based upon the system
time of the computer, and not the IBUC G.
Satellite Network Operations Center Doesn’t Recognize Signal

The IBUC G appears to be transmitting a signal, but the satellite network operations
center (NOC) cannot identify your carrier.
To determine whether your settings are correct,
1. Verify that your frequency is within the bandwidth slot that was allocated to you.
2. Determine whether the IBUC G operates with the LO on the low side or the high
side of the frequency that was allocated to you.
3. Check the signal mix. Remember that low-side is non-inverting and high-side is
inverting.
4. Use the following formulas to calculate IF frequency
low side IF = RF - LO Non-inverting
high side IF = LO - RF Inverting
The LO for each IBUC G band is found in Table 2.1 on page 2-3.
5. Check the Tx output level.
When Tx output power is disabled, the Tx output level will read -99.0 dBm. This is
not an actual power reading; rather it indicates the loss of power.
When conditions cause the automatic shut-off of the Tx output signal, the Tx output
level will read -96.0 dBm. This is not an actual power reading; rather it indicates
the automatic shut-off of power.
Transmit Power in Saturation

The IBUC G gain has been calibrated so that at minimum attenuation, the small signal
gain is, at a minimum, (PSAT + 31) dB. As an example, a 400 W C-band unit has a
minimum gain of 87 dB over frequency and over temperature.

Operating the IBUC G at high levels will result in spectral distortion and high
intermodulation levels. Terrasat recommends operating with power back-off levels
sufficient to meet the spectral density mask.
To avoid signal saturation,
1. Reduce input power from the modem.

2. Increase the attenuation setting of the IBUC G.
Tx Input/Output Level Verification

To verify the Tx IF Input level,
1. Use the Sensor Tab of the embedded Web pages to check levels.
For more information about the Sensor Tab, see page C-12.
2. Compare the reading to your expected level.
The detector range is -55 dBm to -20 dBm.
To verify the Tx RF Output level,
1. Use the Sensor Tab of the embedded Web pages to check levels.
For more information about the Sensor Tab, see page C-12.
2. If your reading does not match your expected level, first verify that the IBUC G is
receiving the proper input level.
3. If the input is at the correct level, use the Transmit Configuration Tab of the
embedded Web pages to modify the attenuation to set the output to the expected
level. The Transmit Configuration Tab is shown on page C-14.
4. If, after setting the output to your expected level, you are still having transmission
problems, check the flexible waveguide and antenna feed for obstructions. Also
check the alignment of the antenna.
Common Errors | 4-9


C HAPTER
5
MONITOR AND CONTROL
CHAPTER 5
FEATURES
This chapter describes the various monitor and control (M&C) features and functions
that the IBUC G offers.
Introduction
You must first establish a communication link with the IBUC G to be able access any
of the M&C interfaces.
M&C Interfaces
The IBUC G offers the following M&C interfaces:
• RS232
• Hand-held terminal
• Multifunction LED
• Frequency Shift Keying Modem Interface
• RS485
• Ethernet
RS232
No additional configuration of the IBUC G is required for proper RS232 operation.
The RS232 port uses ASCII protocol and a fixed baud rate of 9600, 8 stop bits, no
parity, no flow control, and one stop bit for communication.
To initiate an RS232 session,
1. Connect a 19-pin to DB9F cable between the computer and the IBUC G.
Figure G.1 on page G-2 contains a drawing for fabricating a cable.
2. Activate a terminal emulation program such as HyperTerminal.
For information about how to connect using HyperTerminal, see Appendix B,
Using HyperTerminal.
3. Type four grave accent marks (e.g., ` ` ` ` ), and then press Enter.
Although the default mode for the IBUC G is RS232, typing the four grave accent
marks upon activating a terminal emulation program ensures that the unit is in
RS232 mode.
4. Type the password command CPE=1234 and then press Enter.
You can now use the ASCII commands described in Appendix F, ASCII
Command/Response Structure to configure and monitor the IBUC G.
Note: The password entered in Step 4 is the factory default password of 1234. If you
have changed the password, type that value instead.
The RS232 port is shared with the hand-held terminal.
Hand-held Terminal
The hand-held terminal (HHT) shown in Figure 5.1 is an optional item that can be
used to access the IBUC G via port J2 for local monitor and control. No additional
configuration of the IBUC G is necessary.
5-2 | IBUC G Monitor and Control Features

F1 F2 F3 F4
1 2 3 YES
4 5 6 NO
7 8 9 BKSP
. 0 SPACE ENTER
Figure 5.1 IBUC G Hand-held Terminal

To activate the HHT,
1. Connect the supplied cable to the J2 connector on the IBUC G and plug the RJ-11
connector into the HHT.
2. When a flashing cursor is seen in the upper left of the HHT screen, press the
decimal key four times (that is, “. . . .”).
The login screen shown in Figure D.1 on page D-2 will appear.
3. Type the password.
The default password is 1234. If you have changed the password, type that value
instead.
The HHT is now ready to accept commands.
M&C Interfaces | 5-3

Additional information about the HHT is in Appendix D, Hand-held Terminal Menu
Tree.
Multifunction LED
The multifunction LED is mounted on the IBUC G housing and provide visual
indications of IBUC G status. LED colors and modes are as follows:
• Flashing Green - No alarms

• Flashing Red - Minor alarm being reported
• Steady Red - Major alarm being reported
Certain alarms are configurable meaning that you define them as major or minor
alarms when thresholds you set are exceeded. Major alarms will cause relay closure
(Form-C). The alarms shown in Table 5.1 are the factory default configuration.
Thresholds for alarms that are user configurable can be set by using any of the M&C
interfaces described in this chapter.
Table 5.1 Default Alarm Configuration

Alarm State
Major Minor None
Flashing Red
Configurable
Solid RED
Log Only
User
Tx Alarms
DRO out of lock No X
Tx Output Level High Yes X
Tx Output Level Low Yes X
Tx Input Level High Yes X
Tx Input Level Low Yes X
Temperature Alarm Yes X
Tx Simulated Fault No X
10 MHz Reference Fault No X
Input Voltage Out of Range No X
Switch Fault No X
Input Current Out of Range No X
AGC/ALC Target Out of Range No X
AGC/ALC Out of Range No X
AGC/ALC Not Settled No X

You can disable the multifunction LED. Use the ASCII command “CLE” described in
Appendix F, the “External LED” command described in Appendix E, the hand-held
terminal described in Appendix D to disable the LEDs, or the System Configuration
Tab of the Web pages described in Appendix C.
Frequency Shift Keying (FSK) Modem Interface

Several modem brands have the capability to communicate with an IBUC G using an
FSK signal multiplexed onto the IF output connector with the Tx IF signal and the
10 MHz reference signal. The default configuration for the IBUC G is RS485/FSK
Mode 1 which enables compatible modems to use “Legacy Binary” mode to
communicate with the IBUC G. The IBUC G is also capable of FSK communication
using ASCII mode but requires a modem compatible with this method. Refer to the
modem’s documentation for more information about commands and procedures for
FSK communication with the IBUC G.
FSK and RS485 are tied together by the mode of operation (Legacy Binary or ASCII).
Once the mode is selected, both FSK and RS485 will work in the same mode. FSK and
RS485 also share a common address. The message formats for both FSK and RS485
are the same. Transmitter link specifications are detailed in Table 5.2 and receiver link
specifications are detailed in Table 5.3.
Table 5.2 Transmitter Link Specifications

Frequency 650 KHz ±5%
FSK Deviation ±60 KHz nominal (+60 KHz mark)
Deviation Tolerance ±50 KHz minimum; ±70 KHz maximum
Output Level -5 dBm to -15 dBm
Output Impedance 50 
Start Tone 710 KHz
Start Tone Time 10 ms
Table 5.3 Receiver Link Specifications

Locking Range ±32.5 KHz
Input Impedance 50 
Input Sensitivity -15 dBm
FSK data is transmitted at 9600 baud with 8 data bits, no parity, no flow control, and
one stop bit.

Synchronization is maintained by the following method:
1. Once a character is received and the inter-character time exceeds 20 ms, then the
link will reset.
The IBUC G is capable of responding to messages at a rate of one every 20 ms.
2. If the IBUC G does not respond within the maximum response time, the command
should be cyclically repeated.
Note: This synchronization method is true only for Legacy Binary mode (not ASCII).
RS485
The RS485 interface is intended primarily as a network management system (NMS)
interface accessed by an NMS program. You can also access the RS485 interface with
the host computer by using the host computer’s on-board RS485 card or by using an
external RS232-to-RS485 adapter. You can communicate with the IBUC G across
RS485 through ASCII or through the binary protocol known as “Legacy Binary.”
The RS485 interface is a standard two-wire interface (DATA+ and DATA-). The baud
rate is programmable to 1200, 2400, 4800, 9600, 19200, 38400, 57600, or 115200
baud. The data is transmitted asynchronously as 8 bits, no parity, no flow control, and
one stop bit.
To configure RS485, you will need to set the following:
• RS485 Address
• RS485 Delay
• RS485 Baud rate
• Legacy Binary or ASCII mode
You can configure RS485 by using any of the M&C interfaces described in this
chapter.
ASCII Mode
Because Legacy Binary is the default RS485 setting for the IBUC G, you will need to
reconfigure the IBUC G in order to use ASCII mode. You can specify ASCII mode by
using any of the M&C interfaces described in this chapter.
Communication requires an on-board RS485 card in the host computer. However, if

an external interface converter box is used to convert RS232 to RS485, a terminal
emulation program such as HyperTerminal will not function unless the interface
converter box is equipped with an automatic line turnaround capability. Otherwise, a
network management program is required to handle this handshaking requirement.

In HyperTerminal, type the password command, and then press Enter. For example,
<001/CPE=1234 where <001/ is the address of the IBUC G and 1234 is the
default password. When the > prompt re-appears, the IBUC G is ready to accept
commands.
ASCII Mode Command Format

Table 5.4 lists the differences between SET and GET commands in ASCII Mode.
Table 5.4 ASCII Mode Command Format

SET Commands GET Commands
Start of Packet: <  Start of Packet: < 
(ASCII code 60; 1 character) (ASCII code 60; 1 character)
Target Address: (4 characters) Target Address: (4 characters)
Address De-limiter: /  Address De-limiter: / 
(ASCII code 47; 1 character) (ASCII code 47; 1 character)
Instruction code: (3 characters) Instruction code: (3 characters)
Code qualifier: = 
(ASCII code 61 or 63; 1 character) End of Packet: Carriage Return 
(ASCII code 13; 1 character)
For a list of ASCII codes, see Appendix F.
Arguments: (n characters) —
End of Packet: Carriage Return 
—
(ASCII code 13; 1 character)
For GET Commands, the format is as follows:
<address/command[CR}
Example: <0001/COI{CR}
For SET Commands, the format is as follows:
<address/command=XXX[CR}
Example: <0001/CPE=1234{CR}
ASCII Mode Response Format

Start of Packet: > (ASCII code 62; 1 character)
Target Address: (4 characters)
Address De-limiter: / (ASCII code 47; 1 character)
Variable Length Data: (n characters)

End of Packet: Carriage Return (ASCII code 13; 1 character)
Example: >0001/{Variable Length Data}{CR}
Commands and values available in ASCII mode are provided in the command set in
Appendix F.
Legacy Binary Mode

Legacy Binary mode is the default RS485 setting for the IBUC G. In Legacy Binary
Mode, using the BUCMON program that is included on the CD-ROM which
accompanies the unit is the simplest method of communicating with the IBUC G. If
you do not have access to the BUCMON program, you will need to use a separate
network management program.
For the RS485 interface, the packet is encapsulated inside a data link layer packet
which has an address “header” byte and a checksum “trailer” byte. Table 5.5 contains
the packet format.
Table 5.5 Packet Format

Byte Description
RS485 destination address of command. For responses, responder address is
1
shifted left by 4 bits.
2 through 6 Command or response packet data.
7 CHECKSUM: the sum of bytes should equal zero.
Each transmitted command data packet consists of the seven bytes shown in Table 5.6.
Table 5.6 IBUC G Data Packet Byte Configuration

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7
IBUC G
Command Data Byte 1 Data Byte 2 Data Byte 3 Data Byte 4 Check Sum
Address
Where
• Byte 1 contains the IBUC G address that is being queried.

The IBUC G will accept a command only if the first byte contains the appropriate
address.
• Byte 2 contains the major command.
See Appendix E for possible commands.
• Byte 3, Byte 4, Bye 5, and Byte 6 contain the specific command response values.
See Appendix E for possible command responses.

• Byte 7 contains the algebraic sum of Bytes 1 through 6.
Commands are executed only if the checksum coincides.
For more information about response data packet configuration, see Appendix E,
Legacy Binary Command Message Structure.
Ethernet
Using Ethernet, you can communicate with the IBUC G through Telnet (ASCII), the
onboard Web server (HTTP), or through SNMP. The IBUC G uses a static IP
addressing structure and does not support DHCP (Dynamic Host Control Protocol).
The IBUC G is configured at the factory, as follows:
IP Address 192.168.1.21
IP Gateway 192.168.1.1
Subnet Mask 255.255.255.0
Telnet Port 23
Note: Your computer should have a static IP address on the same subnet as the IBUC G.
Using a suitable cable, connect the computer to the J2 connector on the IBUC G.
Note: If an Ethernet hub is not used to connect to the IBUC G, a crossover cable must be
used. However, most current Ethernet cards have an auto-sensing feature which
enables the use of a straight connect cable.
Determining the IP Address of Your IBUC or IBUC G

Follow these steps to determine the IP address of a unit that is not on the same subnet
as the host computer by using the Wireshark® network packet analyzer. Wireshark is
an open source project that also enables you to capture and interactively browse the
traffic running on a computer network.
To download Wireshark,
1. Open a Web browser window and navigate to the Wireshark website at

www.wireshark.org

2. Double-click the Download Wireshark icon shown in Figure 5.2 to begin the
process.
Figure 5.2 Download Wireshark Icon
3. The Download page shown in Figure 5.3 appears. The software will automatically
sense whether your computer is running a 32-bit or 64-bit version of Windows.
Double-click the version that is highlighted to begin the installation process.
In Figure 5.3, a 32-bit verison of Windows was sensed and the 32-bit Windows
Installer is highlighted. Also, the release version number may differ from what
appears in the green bar in Figure 5.3.
Figure 5.3 Wireshark Release Version

4. An executable alert message similar to the one shown in Figure 5.4 appears. Click
Save File to begin downloading and then saving the Wireshark executable file.
Figure 5.4 Executable Alert Message
5. When the files have downloaded, a window similar to the one shown in Figure 5.5
appears. Click Run to begin the Installation Wizard.
Figure 5.5 Open File Security Warning Message

6. The Installation Wizard begins with a welcome window similar to the one shown
in Figure 5.6. Click Next.
Figure 5.6 Installation Wizard Welcome
7. A window containing the license agreement similar to the one shown in Figure 5.7
appears. Click I Agree to continue the installation.
Figure 5.7 Wireshark License Agreement

8. A window containing a list of the various components available for installation
similar to the one shown in Figure 5.8 appears. Terrasat recommends keeping all
default values. Click Next.
Figure 5.8 Choosing Wireshark Components
9. A window containing a list of the additional tasks available for installation similar
to the one shown in Figure 5.9 appears. Terrasat recommends keeping all default
values. Click Next.
Figure 5.9 Selecting Additional Wireshark Tasks

10. A window containing the location for installation similar to the one shown in
Figure 5.10 appears. Terrasat recommends keeping the default location. Click
Next.
Figure 5.10 Choosing the Installation Location
11. A window asking if you want to install WinPcap similar to the one shown in
Figure 5.11 appears. WinPcap is required to capture live network data. Click
Next.
Figure 5.11 Installing WinPcap

12. A window similar to the one shown in Figure 5.12 that contains the progress of the
installation appears.
Figure 5.12 Installation Progress Bar
13. When the Wireshark installation is complete, a window similar to the one shown in
Figure 5.13 that contains the WinPcap Installer wizard appears. Click Next, and
then follow the on-screen prompts.
Figure 5.13 WinPcap Installer

14. Setup of Wireshark is complete when a window similar to the one shown in Figure
5.14 appears. Click Next.
Figure 5.14 Setup Completion Notification
15. A window similar to the one shown in Figure 5.15 appears to notify you that
installation is complete. Click Finish.
Figure 5.15 Finishing Setup of Wireshark

To run Wireshark,
1. Attach the 19-pin M&C cable between your computer and the J2 connector of the
IBUC. If you are using an IBUC G, attach an Ethernet cable between your
computer and the J4 connector of the IBUC G.
2. Double-click the Wireshark icon on the desktop or choose Start → All Programs
→ Wireshark. A new window appears that contains the Wireshark interface.
3. Choose Capture → Interfaces as shown in Figure 5.16. A list of interfaces appears.
Figure 5.16 Wireshark Menu
4. Select the interface for which you need to find the IP address by checking the box
next to its name, and then click Start.
Figure 5.17 Selecting An Interface
5. Cycle power to the IBUC or IBUC G.

6. A results screen similar to the one shown in Figure 5.18 appears. Look for the text
“Gratuitous ARP for <your IP> Request”. In this example, the IP
address has been highlighted.
Figure 5.18 Returning IP Address Information
7. Record the IP address for future reference.
Telnet
Telnet is a simple, text-based program that enables you to connect to another computer
by using the Internet. You can connect to the IBUC G by using a Telnet client from
the host PC. Telnet uses the ASCII command set listed in Appendix F, ASCII
Command/Response Structure. The default port for Telnet is 23. Characters are
echoed back to the user. The response format varies depending on the message setting
type. If the verbose setting is used, the response contains formatting characters which
display neatly to the user. If the terse setting is used, the response contains no
formatting characters and is terminated with LF and CR. If verbose mode is used, the
response is terminated with IBUC>.
To initiate a session,
1. Activate a command prompt window from the host computer.

2. Type Telnet 192.168.1.21 and a cursor should appear on the left of the
screen.
3. Type the password command CPE=1234.
You can now use ASCII commands to configure and monitor the IBUC G. For more
information, see Appendix F.
Web Server
You can access embedded Web pages that contain status and configuration
information.

Connect to the IBUC G M&C and type the IP address of the IBUC G through a Web
browser. A login page then appears. After login, you have a choice of eight Web pages
(nine pages if using redundant IBUC Gs) with monitoring, control, and alarm
information. Individual pages are displayed by clicking the tabs at the top of the Web
page frame. On a redundant transmit system, the display area will contain two frames.
The left side will display the A: side IBUC G and the right will display the B: side
IBUC G
To initiate a session,
1. Activate a Web browser window from the host computer.

2. Type the IP Address of the IBUC G in the address window, and then press Enter.
For more information about the options available on each Web page, see Appendix C .
SNMP
The IBUC G supports SNMP version 1.0 protocol. The SNMP agent listens on Port
161 for SNMP messages and uses Port 162 for transmitting trap information. SNMP
can be configured from the HHT, RS232, Telnet, Web pages, FSK, and RS485
interfaces (ASCII mode required for FSK and RS485).
The MIB-II system group is implemented beginning with version 1.04.
The following commands configure SNMP operation on the IBUC G:
• CIT – Enables or disables the SNMP trap capabilities of the IBUC G.

CIT=1 Enable traps. SNMP must be enabled to generate traps (CIS=1).
CIT=0 Disable traps.
CIT? Displays the current setting of traps.
• CIS – Enables or disables the SNMP functionality of the IBUC G.
CIS=1 Enable SNMPV1.
CIS=0 Disable SNMPV1.
CIS? Displays the current setting of SNMP functionality.
• CIH – Sets the IP address to send traps.
CIH=<value> where value is an IP address in dotted decimal notation.
CIH? Retrieves the current trap IP address from the IBUC G.
• CIC – Sets the SNMP passwords for the IBUC G.
CIC=<public>,<private>,<trap> where public is the public password, private is the
private password, and trap is the trap password.

All three passwords are required when issuing this command.
Each password cannot exceed 16 characters.
Passwords may not be read for security purposes.
To configure SNMP using the hand-held terminal (HHT),
1. Connect the HHT to the IBUC G by using the 19-pin connector.

2. Press the decimal key four times (e.g., . . . .).
The default password is 1234.
4. Press the right arrow key to access the SNMP submenu.
5. Press the 0 key.
6. Press Yes to enable SNMP.
7. Press the Bksp key.
8. Press 1 key.
9. Press Yes to enable traps.
10. Press the Bksp key.
11. Press the 2 key.
12. Type the trap host IP address.
Note: Community strings cannot be set from the hand-held terminal.
To configure SNMP from the Web pages,
1. Connect to the IBUC G with a Web browser.

The default IP address is http://192.168.1.21.
3. Select the Interface Configuration tab.
4. Enable SNMP, SNMP Trap, host trap IP, and set passwords, if desired.
The default is public, private, and trap.
5. Press Submit.
Note: Changing the SNMP passwords requires a firmware reboot.

MIBs
Management information bases (MIBs) are hierarchical virtual databases used to
manage the devices in a communications network. The following MIBs are provided
for the SNMP management station:
• TERRASAT-IBUC-MIB.MIB
• TERRASAT-RX1PLUS1-MIB.MIB
• TERRASAT-SMI-MIB.MIB
• TERRASAT-SSPA-MIB.MIB
• TERRASAT-TC-MIB.MIB
• TERRASAT-TRAPDEF-MIB.MIB
MIB files are included on the CD-ROM supplied with each IBUC G. The MIB files
do not need to be loaded in any particular order.
Power Measurement
The Terrasat IBUC G is capable of accurately reading the input and output power for
a single carrier in either continuous signal mode (CSM) or in burst mode. The dynamic
range for input power is from -55 dBm to -20 dBm and for output power the dynamic
range is from rated power to 20 dB below rated power. Each unit is loaded with a
detector calibration lookup table that compensates for detector variations in frequency,
power level, and temperature. The reported power level is then based on the
user-requested frequency and the internally monitored temperature and power level. If
multiple carriers are present, the composite transmit power level is read but accuracy
is dependent upon the actual carrier frequencies, levels, and modulation being used.
The power measurement occurs in the following two ways:
1. Burst Mode
In burst power measurement mode it is assumed that, in normal operation, a
transmit carrier may or not be present due to the nature of burst mode operation.
Since the transmit burst pulse has a rise time and a fall time and the envelope level
varies during symbol transitions when the signal is modulated, the power must be
reported as a peak value. To maintain detected accuracy of the burst pulse, 128
consecutive measurements of the pulse are taken. Once the initial reading exceeds
the burst threshold, 128 consecutive readings are taken (regardless of level). The
highest value of the 128 is displayed. The IBUC G reports the most recent valid
reading above the burst threshold. Burst threshold values are listed in Table C.2 on
page C-16.
Power Measurement | 5-21

Burst Time: 500 µs to 1 s
Measurement accuracy: ± 2 dB absolute, 1.5 dB p-p relative. Accuracy is
improved as the burst threshold setting is raised closer to the carrier peak.
The detector accuracy is based on a pulsed unmodulated signal with a pulse width
of 500 µs.
2. Continuous Signal Mode (CSM)
In CSM power measurement mode, it is assumed that, in normal operation, a
transmit carrier is always present. Therefore, reported power is the peak power
over 128 consecutive readings.
Measurement accuracy: ±1 dB absolute, 1 dB p-p relative*
The detector accuracy is based on a CW unmodulated carrier.
* Relative measurement accuracy defines the error between any two power
readings at any particular frequency over the dynamic range.
Notes: To make the given accuracy achievable, the operating transmit frequency
information must be provided via M&C in order to use the information in the
detector’s internal calibration look-up table.
By default, the unit will be set to perform CSM measurements.

C HAPTER
6
TROUBLESHOOTING
CHAPTER6
This chapter discusses basic troubleshooting procedures for the Terrasat

Communications, Inc. line of intelligent block upconverters (IBUC Gs) and outdoor
units (ODUs).
Maintenance
In general, Terrasat block upconverters are self-contained and require little
maintenance. However, for optimum performance, Terrasat recommends that users
inspect the mechanics of the system every six months and perform the following:
• Clean the antenna feeds to keep them clear of obstructions.

• Check cables and connectors for signs of wear, damage, or loose connections.
• Check all fan intakes and exhausts to ensure that they are clear of debris.
Transceiver Fault Isolation

Use the information in this section to assist in determining whether a Terrasat unit is
faulty. The intent is to determine a “Go” or “No Go” situation based on alarms
indicated through the M&C ports, as well as by measuring certain signals using test
equipment.
AC Power Problems/Conditioning
In today’s electrical environment, there are many types of power-related problems that
can prevent proper operation of sensitive electronic equipment. These problems or
disturbances can be caused by things such as voltage induced by lightning, switching
high-power electrical equipment On/Off, or utility company actions such as power
factor correction. Serious problems can arise with the occurrence of transients and
spikes which can cause random errors or even failure of the circuitry.
Whatever the origin of the transients, they can be classified into two simple categories:
• Common Mode
Noise voltage that appears equally and in phase from each signal conductor to
ground. (The term "common" refers to the fact that identical noise appears on both
the active and neutral wires.) Common-mode noise poses a threat because the
noise attempts to dissipate its energy from neutral to ground or from active to
ground.
• Normal Mode
Noise potential between the power line conductors. It adds to and subtracts from
the power line sinusoidal voltage wave and is sometimes referred to as
differential-mode noise or transverse-mode noise. Normal-mode noise attempts to
dissipate its energy along any path from line to neutral. If the normal-mode noise
has sufficient voltage (or energy), damage can occur.
Category A
At the wall outlets (and more than 30 ft. [9 m] from a distribution panel), the typical
noise is a 0.5 s rise time up to 6 kV peak open circuit voltage, 100 kHz ring wave
with 200 ampere short circuit current capability.
Category B
At the distribution panel, one can experience the 100 kHz ring wave listed previously
but with 500 ampere current capability and a unidirectional impulse up to 6 kV
potential rising in 1.2 s and decaying to half voltage in 50 s. Accompanying this can
be a short circuit current up to 3 000 amperes rising to peak in 8s and decaying to
half value in 20 s.
To ensure uninterrupted service, Terrasat recommends using a line conditioner or

uninterruptible power supply (UPS) based on the expected AC power at the site.
Site-Related Problems
VSAT antennas are often fitted at the top of buildings. Avoid close proximity to
elevator motors, and such. Ensure that the satellite signal path is free and clear of
obstructions.
M&C Checks
When troubleshooting the IBUC G, the first level of troubleshooting should be to
check the status through the M&C port. Alarms and an alarm history log are available
with the IBUC G M&C. For specific information about using the RS232, RS485,
Ethernet, or hand-held terminal ports, see Chapter 5, Monitor and Control Features.
6-2 | IBUC G Troubleshooting

Transmit Power Setting
There have been several cases reported to Terrasat Technical Support where the
transmit power has been turned up to or near saturation while transmitting a digital
carrier. This most likely will result in spectral distortion, re-growth, and
intermodulation products for multi-carrier operation. To reduce saturation, reduce the
input level or increase the attenuation.
Note: When transmitting digital carriers, it is customary to operate the power amplifier
system with an output back off (OBO) sufficient to meet the spectral density mask
requirements and interference requirements of multi-carrier operation.
Transmit Intermediate Frequency Input Level Verification

If low or no Tx output power is detected, begin troubleshooting by checking the input
to the IBUC G.
1. Check the Tx Input Level displayed in M&C or disconnect the cable at the
IBUC G J1 connector (Tx L-band) and use a spectrum analyzer to measure the
power level of the L-band signal at the output of the coaxial cable that connects to
the IBUC G at J1 (Tx L-band). The L-band signal level should be within the range
of -20 dBm through -55 dBm. If it is not, check the cable and modem output.
2. If the L-band signal is within range, check that the 10 MHz reference signal is
within the range of +5 dBm through -12 dBm and is distortion free. If it is not,
check the cable and modem output (or IFU Tx Out).
IBUC G Transmit Output Verification

This check assumes that the L-band and 10 MHz inputs are at the correct levels.
1. Tx Output level is monitored and displayed in the IBUC G M&C. Alternatively,

you can connect a cross coupler and a high-power termination to the IBUC G Tx
waveguide output.
2. Measure the Tx RF output with the spectrum analyzer connected at the waveguide
output. Ensure that the cable loss of the cable being used for the measurement has
been taken into account.
3. RF power should be between rated power and no lower than 25 dB below rated
power. If it is not, the IBUC G is defective and should be returned to the factory
for repair. Instructions for returning a unit for repair are on page 6-7.
4. If the IBUC G Tx RF output measures within specification, ensure that the
waveguide, feedhorn, and antenna are properly aligned.
Maintenance | 6-3
Common Problems
The following problems or occurrences have been noted during normal
troubleshooting.
Tx Output is Disabled
When the Tx Output is set to Disabled, the Tx Output level shown on the Sensor Tab
on page C-12 reads -99.00 dBm. This is not an actual reading.
However, when conditions cause the automatic shut-off of the Tx Output signal, the
Tx Output is muted and the Tx Output level on the Sensor Tab shown on page C-12
reads -96.00 dBm.
Incorrect Frequency Settings

If the Satellite Network Operations Center (NOC) does not recognize your signal, see
page 4-8 for additional information.
Damaged Cables
RF coaxial cable damaged due to improper handling (such as contact damage due to
improper mating; cable insulation that is damaged, crushed, cut, or charred; cables
were not discharged prior to connecting them; or conductors that are nicked, gouged,
damaged, or severed) may impair system performance and reliability. Do not attempt
to repair broken or damaged coaxial cables unless absolutely necessary. Replace the
entire cable whenever possible.
Damaged cabling and incorrectly tightened connectors can leak RF energy, which
may lead to excessive levels in their immediate vicinity.
CAUTION
Never disconnect RF cables or connectors
associated with a transmitter in operation
since this may result in an RF burn through
direct contact with RF conductors.
10 MHz Reference Signal at the IBUC G is at the Wrong Level or Missing

A 10 MHz input is used to provide a stable reference frequency to which the
phase-locked local oscillator (or PLDRO) synchronizes. The 10 MHz reference signal
level should be between -12 dBm to +5 dBm.
When the IBUC G senses that the phase-locked local oscillator has gone out of lock, a
PLDRO Lock alarm is triggered. This alarm then initiates a series of routines that

leads to the muting of the power amplifier (that is, the IBUC G is automatically
shut-off). Table 6.1 lists four possible scenarios caused by changes in the 10 MHz
reference signal or whether the PLDRO is locked.
Table 6.1 Possible Scenarios for IBUC Gs with an External 10 MHz Reference Signal
10 MHz Reference Phase-Locked

Signal Level Local Oscillator Results
Causes a minor alarm (10 MHz Detector). Unit is still transmitting.
Low Locked Check the 10 MHz signal level. Resultant phase noise may be
degraded.
Causes a major alarm (PLDRO Out of Lock). Power amplifier is

muted and the IBUC G is automatically shut-off. Check the 10 MHz
Low Out-of-Lock
reference signal level and whether the 10 MHz reference signal is
enabled at the modem.
Within Specifications Locked Unit is operating normally. No alarms are present.
Causes a major alarm (PLDRO Out of Lock). Power amplifier is

Within Specifications Out-of-Lock muted and the IBUC G is automatically shut-off. PLDRO may be
faulty and the IBUC G might need to be returned for repair.
Antenna is Pointed Toward Wrong Satellite or is Misaligned

Transmission to the wrong satellite or on the wrong polarization or channel can cause
interference with other satellite users and may result in fines from the satellite
operator.
To ensure that your antenna is aligned with the correct satellite,
1. Follow the antenna manufacturer’s instructions to verify the azimuth, elevation,

and polarization settings.
2. Follow the antenna manufacturer’s instructions to move the antenna into a position
that provides maximum signal strength.
3. Establish a communications link with the satellite network operations center
(NOC).
4. Peak the signal on the satellite, and then adjust polarization per guidance from
NOC staff.
Moisture Migrated Into the IBUC G

Moisture can enter and damage the IBUC G if waveguide gaskets are missing, there is
a hole in the feed window, or there is a break in the coaxial connectors.
Maintenance | 6-5
To prevent moisture from entering the IBUC G,
• Ensure that the paper label is removed from the waveguidre prior to installation
and operation.
• Ensure that the rubber waveguide gasket is intact and fully seated in the grooved
channel before making the connection.
• Use water-resistant wrap (or mastic tape) on all outdoor connectors to ensure a
water-tight seal. Mastic tapes are designed to flow and self-heal if cut or punctured
For more information about applying water-resistant wrap, see page 3-12.
• Avoid using damaged connectors (for example, scratched mating surfaces,
eccentric or bent center conductors, and so on.).
• Seal all coaxial cable fittings with putty.
Bad Orthogonal Mode Transducer and/or Antenna

If the antenna feedhorn and orthogonal mode transducer (OMT) are not positioned
correctly, the IBUC G will not operate properly.
To position the feedhorn and OMT,
• Refer to the antenna manufacturer’s assembly instructions to verify that the

feedhorn and OMT were mounted correctly on the antenna.
• Establish a communications link with the satellite network operations center
(NOC).
• Guided by NOC staff, slowly rotate the outdoor equipment to the appropriate
position.
• If rotation is impossible, it is likely that there ia a problem with OMT and it will
need to be returned to the antenna manufacturer.
LED is Red
A red LED indicates only that a fault (or alarm) has occurred and does not necessarily
indicate that transmission has stopped. A flashing red light indicates a minor alarm
and a solid red light indicates a major alarm. You can communicate with the IBUC G
to determine what is causing the fault, and then clear the fault condition.
1. Establish a connection with the IBUC G by using any of the M&C interfaces.
2. View the Alarm Status Tab (shown on page C-8) to determine the current alarm.
3. View the Sensor Tab (shown on page C-12) to determine which sensor reading
caused the alarm.
4. Compare your readings to the thresholds.

5. Adjust the threshold level(s) to bring the reading(s) within specifications and thus
clear the fault
When the fault is cleared, the LED should be flashing green.
Repair Policy
The Terrasat IBUC G is not field repairable.
In the event that a failure has been detected, it might be necessary to return the
defective unit to the factory or a factory-authorized service center. The following
section contains instructions for returning a defective unit to the factory for repair.
Returned Material Authorization (RMA)

If any equipment is determined to be defective:
• Have the following information available:

• Unit serial number
• Unit part number and description
• Complete description of the failure
• Designated contact name and phone number
• Billing information
• Shipping information
• Contact Terrasat Customer Service to request an RMA number.
• By telephone +1 408-782-2166
• By e-mail to [email protected]
• Properly package the defective equipment in its original container (if available and
undamaged), and mark the RMA number on the outside of the shipping container.
Note: Do not return any equipment without an RMA number.
• Ship the equipment to the following address:
Terrasat Communications, Inc.
235 Vineyard Court
Morgan Hill, CA 95037
U.S.A.
• After the unit is received at Terrasat, an initial evaluation will be performed.
• If the unit is found to be in-warranty, the unit will be repaired and returned at
no charge.
Repair Policy | 6-7

• If the unit is found to be out-of-warranty, Terrasat Customer Service will
contact the designated contact for authorization to proceed with the repair.
• Authorization in the form of a purchase order will be required.
• Once authorization is received, the unit will be repaired and returned.

C HAPTER
7
TRANSMIT REDUNDANT SYSTEMS
CHAPTER 7
The IBUC G can be installed and configured as a redundant system providing

automatic switching to a standby unit if the primary unit fails. The outdoor power
supplies are configured in pairs to provide full system redundancy.
Description
A transmit redundant (or Tx 1+1) system includes two IBUC Gs of the same
frequency band connected to an interface module and an RF switch. IBUC Gs can be
connected to AC mains. The two IBUC Gs, the interface module, and the RF switch
are typically mounted on a common mounting plate (as shown in Figure 7.1) and
connected with supplied cables and waveguide components.
.
Figure 7.1 Transmit Redundant System Setup
Figure 7.2 is a photograph of the same system but from the rear. This photograph
gives a better perspective of the waveguide connections.
Figure 7.2 Waveguide Connecting Two IBUC G Units
7-2 | IBUC G Transmit Redundant Systems

Interface for Tx Redundant (1+1) Systems
The Tx 1+1 interface module is a passive unit. The module divides the frequency shift
keying (FSK), 10 MHz reference and L-band signals, as well as routes the Ethernet
connection to the IBUC Gs through an Ethernet switch. It supports various interface
connectors and includes a bank of LEDs for visual indication of alarm conditions. The
user interface is one of the following: via Web browser to embedded Web pages, TCP /
IP through a Telnet session, UDP through SNMP, RS485, hand-held terminal, RS232,
as well as FSK link to both IBUC Gs.
The system provides automatic switching between IBUC Gs in the event of failure.
The IBUC Gs communicate with each other to monitor status and execute switching
logic. A software command is available in the IBUC G to enable the unit designated
as the Master to clone itself to the Slave to match the unit’s configuration. Monitor and
Control (M&C) functions are available through the interface module via hand-held
terminal, RS232, RS485, TCP/IP, and FSK. Two Form-C relays are provided for
alarms (one for the A: side IBUC G and one for the B: side IBUC G). In the
redundant system, remote M&C by using RS485 and TCP/IP is available via the
interface module which eliminates the need to run two separate M&C cables to the
IBUC Gs. In the case of FSK, M&C is available on the IFL cable and no additional
cables are required. M&C commands for redundant systems are present in the
IBUC G software. For more information about ASCII commands, see Appendix F.
Description | 7-3
Figure 7.3
RS485, HHT, RS232, Alarms, Switch Command & Indicator
FSK, 10 MHz, L-band
AC Mains
Ethernet
Tx A: Out
J1
J1
Power Supply A:
M&C Interface
Tx In
J2
Tx In
J1
Tx B: Out
J3
Ethernet
Divider
J2
RF Out
IBUC G A:
J4
BUC A: INT
J4
User Interface
0
J11
Ethernet
J5
BUC A: ETH
J1
Tx RF
User Interface

Waveguide Switch
RS485, HHT, RS232, TCP/IP, Alarms
J2
BUC B: INT
J6
IBUC G B:
RF Out
J4
FSK, 10 MHz, L-band

BUC B: ETH
J7
Switch
Ethernet
J8
User INT - ETH
IBUC G Interface Module

J1
Power Supply B:
IBUC G Redundant System Diagram

User INT – M&C
J9
Aux ETH
J10
M&C Interface
Tx In
AC Mains
Ethernet
RS485, HHT, RS232, Alarms, Switch Command & Indicator
Modem
FSK, 10 MHz, L-band
Ethernet
J2
J4
Aux. Interface - Ethernet
LNB A:
J1
Figure 7.3 is a diagram of a typical redundant system.
User I/O TCP/IP,

RS485, HHT
J5
0
Rx RF
Rx 1+1
Interface
J6
J7
L-band Rx, 10 MHz, FSK LNB B:
J3
Component Descriptions
As described previously, the redundant transmit system includes two IBUC Gs of the
same frequency band connected to an interface module at the input and an RF switch
at the output. This section explains the functionality of each component and their
relationships.
Intelligent Block Upconverter (IBUC G)

More information about the intelligent block upconverter is found in Chapter 2,
Functional Description.
Tx 1+1 Interface Module

The Tx 1+1 interface module is powered by both IBUC Gs through connectors J4 (for
the A: side IBUC G) and J6 (for the B: side IBUC G). Both supply inputs feed a
linear regulator that generates the voltage for all internal circuitry. The RS232
interface and the power for the hand-held terminal are routed to connector J9. The
RS485 interfaces coming from both IBUC Gs via connectors J4 and J6 are connected
together and routed to the user interface via connector J9. The Ethernet ports from the
A: side IBUC G and the B: side IBUC G (connectors J5 and J7, respectively) are
routed to the user interface through an internal Ethernet switch. The alarm output
(normally open, faulted, or short to ground) of the A: side IBUC G is routed to the
alarm input of the B: side IBUC G and vice-versa. This setup ensures that the A: side
IBUC G and the B: side IBUC G monitor each other. Also, the Form-C relays with
the alarms of both IBUC Gs are routed to the interface via connector J9. The switch
commands from the A: side IBUC G and the B: side IBUC G are connected together
and routed to the waveguide switch (connector J11). The waveguide switch indicators
(connector J11) are routed to both IBUC Gs (connectors J4 and J6). The Tx Input
(L-band, 10 MHz and FSK) from connector J2 is routed to a splitter. The outputs of
the splitter are routed to connector J1 (the A: side Tx output) and J3 (the B: side Tx
output). The Tx 1+1 module also has a bank of LEDs that provide a visual indication
of the power, Ethernet activity for both IBUC Gs, the RJ45 user interface (J8), the
19-pin user interface (J9), the auxiliary user interface (J10), the status of both
IBUC Gs, as well as which IBUC G is online.
Figure 7.4 is a block diagram of a Tx 1+1 interface module.
Component Descriptions | 7-5

LEDs
FSK, 10 MHz, L-band

Tx A: Out J1
Tx In FSK, 10 MHz, L-band

Splitter
J2
FSK, 10 MHz, L-band

J3
Tx B: Out
BUC A: RS485, HHT, RS232, Alarms,

J4
Interface Switch Control & Indicator
WG Switch
BUC A: Ethernet
Interconnect
J5
J11
Ethernet
BUC B: RS485, HHT, RS232, Alarms,

J6
Interface Switch Control & Indicator
BUC B: Ethernet
J7
Ethernet
User Interface Ethernet Ethernet Switch

J8
Ethernet
TCP/IP
User Interface
J9
M&C
RS485, HHT, RS232, Alarms, Switch Control & Indicator
J10
Aux Ethernet
Figure 7.4 Tx 1+1 Interface Module Block Diagram
Waveguide Switch
Redundant systems are provided with the waveguide switch. A switch cable, which is
used to connect the Tx and Rx Interface to the switch, is also included.
Software
Both Tx and Rx redundant systems monitor and control several parameters and have
features to simplify installation and use of the redundant systems as well as enhance
system performance.

Some of the key features include:
• Monitor and Control

Redundant systems can be monitored and controlled through an assortment of
interfaces including RS232, RS485, Ethernet port, an optional hand-held terminal,
or via an FSK link with compatible modems.
• Tx Redundancy
The IBUC Gs automatically sense when they are configured in redundancy mode.
The logic for redundant operation is built in, eliminating the need for an external
switching controller.
• Autocloning
The Master IBUC G (online) periodically updates the Slave IBUC G (standby)
with configuration data. This enables you to configure the system by configuring
only the Master IBUC G. The Slave IBUC G then becomes a “clone” of the
Master when autocloning is enabled.
• Embedded Web pages
Provide management for small networks by using a Web browser.
• Alarm History
A log of alarms that occur is maintained. This can simplify troubleshooting of the
system—especially if an intermittent problem occurs.
For a full description of M&C functions, see Chapter 5, Monitor and Control Features.
Installation and Setup

The redundant Terrasat outdoor unit (ODU) consists of two IBUC Gs mounted on a
common plate, redundant power supplies, and a set of interconnection cables. It can
also include an Rx 1+1 redundant system.
This section contains the general requirements for installation of the redundant ODU
to the antenna.
Installation and Setup | 7-7

WARNING
For protection of personnel and
equipment, use care when installing the
antenna and whenever working on or
around the system.

Follow standard safety precautions when
using hand and/or power tools.

Use care when working with dangerous
voltages.
System Cabling Requirements
Tx 1+1 System
Both the A: side IBUC G and the B: side IBUC G connect to the interface module
via a coaxial cable connection (J1) carrying the L-band, 10 MHz reference and FSK
M&C signals, where appropriate. A connector on the IBUC G (J2) connects to the
interface module that provides the M&C interface. An additional connector (J4) is
used for TCP/IP between the IBUC Gs and the interface module IBUC G waveguide
outputs are connected to ports on the Tx RF switch using waveguide bends. AC power
is provided via AC mains for AC-powered IBUC Gs at connector J3.
The Tx waveguide switch provides the uplink signal to the antenna feed via a
waveguide (customer supplied) or coaxial cable, as required. Power and switching
control are carried on an interface cable from the switch to the interface module.
The interface module provides eleven connectors for interfacing the IFL, the IBUC G
RF switch, and M&C functions. Status LEDs built in to the interface module provide
visual system status, as shown in Figure 7.5. Remote M&C for the 1+1 system is
available by using RS485 or TCP/IP. Systems with FSK-capable modems also have
M&C functions available at the modem’s front panel. Local monitoring and control is
available by using a hand-held terminal connected at the interface module.

Tx 1+1 Interface Module
Figure 7.5 depicts the top view of an interface module of a Tx 1+1 system and
identifies the locations of the various connectors.
Figure 7.5 Tx 1+1 Interface Module Top View
More information about the multifunction LEDs can be found on page 7-24.
Physical Connections
Table 7.1 contains information about the various interface connectors and their mates
for a Tx 1+1 Interface Module.
Table 7.1 Tx 1+1 Interface Module Connector Schedule

Reference
Designator Function Interface Connector Interface Connector Mate
J1 A: side Tx Output TYPE-N, SOCKET TYPE-N, PLUG
J2 Tx Input TYPE-N, SOCKET TYPE-N, PLUG
J3 B: side Tx Output TYPE-N, SOCKET TYPE-N, PLUG
MS CIRCULAR CONNECTOR, MS CIRCULAR CONNECTOR,

A: Side IBUC G
J4 BOX MTG SOCKET, 19S  STRAIGHT PLUG, 19P 
Interface
(MS3112E-14-19P) (MS3116F-14-19S)
RJ-45-IP67 SHIELDED INLINE
A: Side IBUC G RJ-45-IP67 PLUG
J5 CONNECTOR WITH CAP
Ethernet (CONEC TECH. 17-101794)
(CONEC TECH. 17-103794)

B: Side IBUC G
J6 BOX MTG SOCKET, 19S  STRAIGHT PLUG, 19P 
Interface
(MS3112E-14-19P) (MS3116F-14-19S)

Table 7.1 Tx 1+1 Interface Module Connector Schedule (Continued)

B: Side IBUC G RJ-45-IP67 PLUG
J7 CONNECTOR WITH CAP
Ethernet (CONEC TECH. 17-101794)
(CONEC TECH. 17-103794)

RJ-45-IP67 PLUG
J8 User Interface Ethernet CONNECTOR WITH CAP
(CONEC TECH. 17-101794)
(CONEC TECH. 17-103794)

J9 User Interface BOX MTG SOCKET, 19S  STRAIGHT PLUG, 19P 
(MS3112E-14-19S) (MS3116F-14-19P)

RJ-45-IP67 PLUG
J10 Auxiliary Ethernet CONNECTOR WITH CAP
(CONEC TECH. 17-101794)
(CONEC TECH. 17-103794)

J11 Waveguide Switch BOX MTG SOCKET, 6S  STRAIGHT PLUG, 6P 
(MS3112E-14-6S) (MS3116F-14-6P)
A mating M&C connector for J3 is provided with the Tx 1+1 system.
J1, J2, and J3

The A: side Tx Output (J1), Tx Input (J2), and B: side Tx Output (J3) connectors are
Type-N connectors.
Table 7.2 Pin Assignments for M&C Interface Connectors J1, J2, and J3
Reference
Designator Function
J1 TX A: OUTPUT, L-BAND, 10 MHz, FSK
J2 TX INPUT, L-BAND, 10 MHz, FSK
J3 TX B: OUTPUT, L-BAND, 10 MHz, FSK
M&C Interface J4 and J6

The M&C interface connectors are 19-pin circular connectors used to enable the
IBUC Gs to exchange communication and status, as well as monitor and control the
waveguide switch. Pin assignments are shown in Table 7.3. The M&C cables used to
connect the Tx 1+1 interface module to the IBUC Gs are supplied with the Tx 1+1
system.
Table 7.3 Pin Assignments for M&C Interface Connectors J4 and J6

Pin Function
A RS485 (+)

Table 7.3 Pin Assignments for M&C Interface Connectors J4 and J6 (Continued)
Pin Function
B RS485 (-)
C HAND-HELD TERMINAL POWER (+)
D RS232 RXD
E RS232 TXD
F HAND-HELD TERMINAL POWER (-)
G ALARM OUTPUT
H NOT USED
J NOT USED
K NOT USED
L IBUC G ALARM OUTPUT Normally Open
M IBUC G ALARM OUTPUT Common
N IBUC G ALARM INPUT/MUTE
P IBUC G ALARM OUTPUT Normally Closed
R 1+1 SWITCH COMMAND A:
S 1+1 SWITCH COMMAND B:
T 1+1 SWITCH INDICATOR A:
U 1+1 SWITCH INDICATOR B:
V 1+1 REDUNDANCY ENABLE
Transmit Output J5, J7, J8, and J10

The J5, J7, J8 and J10 connectors are shielded Ethernet connectors used to enable
remote monitoring and control of the Tx 1+1 System operating parameters. Pin
assignments are listed in Table 7.4.
Table 7.4 Pin Assignments for M&C Interface Connector J5, J7, J8, and J10
Pin Function
1 TCP/IP TX (+)
2 TCP/IP TX (-)
3 TCP/IP RX (+)
4 N/C
5 N/C
6 TCP/IP RX (-)
7 N/C
8 N/C

User Interface J9
The User Interface connector is a 19-pin circular connector used to enable remote
monitoring and control of the Tx 1+1 System operating parameters. The J9 connector
enables use of RS485, the hand-held terminal (HHT), RS232, and alarms. Pin
assignments are shown in Table 7.5. If the user interface port of the Tx 1+1 interface
module is going to be used, the cable should be a shielded multi-conductor cable with
at least two each twisted pairs. The twisted pairs used for TCP/IP must have an
impedance of 100 ohms. For cable drawings, see Appendix G. An assembled IP cable
is available from Terrasat.
Note: Customers who order a hand-held terminal (HHT) will receive two cables: one is
wired specifically for the A: side IBUC G and the other is wired specifically for the
B: side IBUC G. The cables are marked for usage.
Table 7.5 Pin Assignments for M&C Interface Connector J9

Pin Function
A RS485 (+)
B RS485 (-)
C HAND-HELD TERMINAL POWER (+)
D A: HAND-HELD TERMINAL, RS232_RXD
E A: HAND-HELD TERMINAL, RS232_TXD
F HAND-HELD TERMINAL, RS232, RS485 COMMON
G TCP/IP TX+
H TCP/IP TX-
J TCP/IP RX+
K TCP/IP RX-
L A: IBUC G ALARM OUTPUT Normally Open
M A: IBUC G ALARM OUTPUT Common (GND)
N A: IBUC G ALARM OUTPUT Normally Open
P B: IBUC G ALARM OUTPUT Normally Open
R B: IBUC G ALARM OUTPUT Common (GND)
S B: IBUC G ALARM OUTPUT Normally Closed
T B: HAND-HELD TERMINAL, RS232_RXD
U B: HAND-HELD TERMINAL, RS232_TXD
V NOT USED
Waveguide Switch Control/Indicator J11

The waveguide switch control/indicator connector is a 6-pin circular connector used to
enable the Tx 1+1 system to monitor and control the waveguide switch. The cable that

connects the Tx 1+1 interface module and the waveguide switch is supplied with the
system..
Table 7.6 Pin Assignments for M&C Interface Connector J11

Pin Function
A SWITCH POSITION A: COMMAND
B SWITCH POSITION A: COMMON
C SWITCH POSITION B: COMMAND
D SWITCH INDICATOR A:
E SWITCH POSITION B: COMMON
F SWITCH INDICATOR B:
Cable and Waveguide Connections
WARNING
Ensure that all power is disconnected
prior to making these connections.
When installing the cable and waveguide assemblies, ensure that all connections are
weather tight. If the optional Rx reject filter is being used, attach it to the Tx
Redundancy waveguide output. Ensure that proper gasketing is used to prevent water
damage.
outdoor connectors to prevent water entry and subsequent water damage. Mastic tapes
are designed to flow and self-heal if cut or punctured. When applied spirally with the
proper tension, mastic tapes form a tight, continuous coating that permits little or no
moisture absorption or penetration. Terrasat provides water-resistant sealing tape for
Type-F and Type-N connectors.
and dirt.
2. Cut the mastic tape to the desired size. The tape should be long enough to cover the
connector completely.

both ends of the tape have formed around the connector and the cable without any
gaps.
Typical Initial Setup

1. Connect the IFL coaxial cable between the Tx 1+1 interface module connector J2
(Tx L-band In) and the modem Tx L-band Out.
2. Connect one M&C cable between the J4 connector of the Tx 1+1 interface
module and the J2 connector of the A: side IBUC G (User Interface) and another
M&C cable between the J6 connector of the Tx 1+1 interface module and the J2
connector of the B: side IBUC G .
3. Connect one Ethernet cable between the J5 connector of the Tx 1+1 interface
module and the J4 connector of the A: side IBUC G and another Ethernet cable
between the J7 connector Tx 1+1 interface module and the J4 connector of the
B: side IBUC G.
4. Connect a section of flexible waveguide between the OMT transmit port and the
Tx RF Output from the waveguide switch (or optional Rx reject filter). The
waveguide should be attached to the antenna feed according to the manufacturer's
instructions. Ensure that proper gasketing is used to prevent water damage.
5. Connect the waveguide switch cable between the J11 connector of the Tx 1+1
interface module and the 6-pin connector on the waveguide switch.
6. Connect one coaxial cable between the J1 connector of the Tx 1+1 interface
module and the J1 connector of the A: side IBUC G and another coaxial cable
between the J3 connector of the Tx 1+1 interface module and the J1 connector of
the B: side IBUC G.
7. Connect the AC cable between the AC Input connector and the AC power source.
Note: Figure 7.3 on page 7-4 illustrates these connections.
outdoor connectors to prevent water entry and subsequent water damage. Mastic tapes
are designed to flow and self-heal if cut or punctured. When applied spirally with the
proper tension, mastic tapes form a tight, continuous coating that permits little or no
moisture absorption or penetration. Terrasat provides water-resistant sealing tape for
Type-F and Type-N connectors.

and dirt.
2. Cut the mastic tape to the desired size. The tape should be long enough to cover the
connector completely.
both ends of the tape have formed around the connector and the cable without any
gaps.
Grounding
Antenna Recommendations
Most antenna masts are encapsulated in concrete. Typically, the mast pipe is
submerged in a 4 ft to 5 ft (1.22 m to 1.53 m) deep augured hole. This provides a good
Ufer ground. An Ufer ground encases grounding conductors in concrete. Concrete
absorbs moisture quickly, yet retains that moisture for a period of time (as much as 15
to 30 days after rain or snow melt). The concrete’s large volume and great area of
contact with the surrounding soil enable a good transfer to the ground.
In the concrete base, an Ufer ground can be established by running a #4 gauge solid
wire or rebar and connecting with pigtails to the base of the pedestal.
The Ufer ground is only one step in proper grounding. The Ufer ground should be
augmented with coupled pairs of 10 ft (3.05 m) rods, placed 20 ft (6.1 m) into the
ground, spaced 20 ft (6.1 m) apart. The first rod should be placed close to the antenna.
The second rod should be placed towards the equipment enclosure. Connect the rods
and antenna mount with #2 gauge wire. A ground rod should be placed at the
equipment enclosure as well. If it is virtually impossible to install the ground rods,
then radials are needed. This can be accomplished by laying 10 or more lengths of
1½-in. (3.81 cm) copper strap, at least 50 ft (15.24 m) long, in a radial fashion around
the antenna base. The straps should be buried, if possible. The hub must be
interconnected to the utility ground.
The ground configuration can vary from one location to another. It is best to measure
the soil conductivity and design a 5 Ω ground system. To protect the system from a
direct strike, a lightning rod placed 2 ft (61 cm) higher than the highest point of the
dish should be interconnected to the Ufer ground with #2 gauge copper wire.

Tx Redundancy Grounding Recommendations
Grounding and lightning protection is recommended as follows.
• Cable Shielding
The shield currents can be eliminated with proper techniques. A grounding strap at
the end of the coaxial and data cables should be connected to the ground lug at the
antenna base with a #4 gauge copper wire. This provides a path of least resistance
prior to entering the electronic equipment.
• AC
The best way to protect the equipment is to have two protectors. The first is the
power mains protector that is mounted directly across the mains in the breaker
box. The second should be mounted or grounded directly at the base or hub of the
antenna or at the 19-in. rack.
• Data and Control Lines
The I/O lines can deliver surge current to the equipment and should be protected as
well.
• Electrical Grounding
Grounding the IBUC G is recommended to prevent possible damage from
lightning and/or other induced electrical surges. Terrasat recommends that 3/0 or
4/0 AWG (American Wire Gauge) stranded copper wire be used to bond the
IBUC G to the earth ground (grounding rod), using the most direct (or shortest)
route.
System Alignment and Operation

General
The following sections outline the procedure for setup and alignment of the earth
station. Prior to ODU alignment, the antenna should be set to the desired azimuth and
elevation settings per manufacturer’s instructions.
CAUTION
The Transmit Redundant System must not
transmit until alignment and any
necessary adjustments are complete.

Test Equipment
Terrasat recommends the equipment or its equivalent listed in Table 7.7 for
installation and system alignment.
Table 7.7 Recommended Test Equipment

Equipment Type
Spectrum Analyzer Agilent HP8563E
Digital Voltmeter Fluke 8050
Cross coupler Used with all bands
RF cables With calibrated insertion loss up to 15 GHz
Waveguide High-power Termination High power to match HPA output
Assortment of cables, connectors and adapters
(calibrated up to 15 GHz)
Ensure that the Tx output power is disabled to prevent accidental transmission

interference with adjacent satellites or transponders before attempting to align or
performing any other operation involving the ODU. Before attempting any system
change, carefully evaluate the possible effects of the transmitted signal.
Setting the Tx Frequencies

All transmit and receive frequencies are set by using the modem.
For a direct connection to an L-band modem, follow the manufacturer’s instructions

on setting the transmit and receive frequencies.
Tx Power Alignment
Transmit L-band Input Adjustment with Modem or Converter

To set the power level of the modulator output:
1. Use a spectrum analyzer to measure the power level of the L-band signal at the
output of the coaxial cable that connects to the Tx 1+1 interface module at J2 (Tx
L-band).
2. Use the modem or converter level adjust to increase and decrease the power level.
Adjust to reach a low level (that is, a level that is no higher than -34 dBm).
3. Check that the 10 MHz reference signal is within the range of +5 dBm to -12 dBm.
Note: The IBUC G requires a 10 MHz reference signal to operate. Check the model
number of the IBUC G to determine whether an external 10 MHz signal is
required.
System Alignment and Operation | 7-17

Transmit RF Output Adjustment with Modem or Converter

To adjust the power level of the IBUC G transmitter output:
1. Ensure that the power level at the input of the IBUC G does not exceed -40 dBm
at startup.
Note: For more information about howto set the Tx frequency, see Setting the Tx
Frequency (L-band) on page 4-4.
2. Ensure that the 10 MHz reference signal (either internal or external) is present
3. Apply power to the IBUC Gs.
4. Enable the Tx signals in the modem or converter and the IBUC Gs.
5. With a satellite modem: Adjust the RF output to the designated power level
(provided by the satellite network operations center or its engineering staff) with
the L-band output (modem) level adjust. Do this for both systems (A: side and
B: side). Equalize the gains by using the gain setting control of the IBUC Gs.
Note: There are differences between the units and the autocloning feature does not
transfer the attenuator settings from the Master(or online) unit to the Slave (or
standby) unit.
6. Under the guidance of the network operations center, fine-adjust the transmit
power for the desired downlink margin at the receiving station by adjusting the Tx
L-band output level adjust (modem or converter output).
Note: For more information about configuring the IBUC Gs, see Chapter 4, Operations. For
more information about configuring and operating in redundant mode, see the
Redundancy Configuration Tab on page C-27.
Final Checks
To ensure optimum operation, inspect the system for crimped or pinched cabling.
Make sure all connections are secure. Once the system has been aligned and is
operating satisfactorily, it will require infrequent and simple maintenance procedures
as described in Maintenance on page 6-1.

M&C Setup
Tx Redundant System
Default Values
A: SIDE IBUC G
RS485 Data Rate is 9600 baud
RS485/FSK Mode is 1 (Legacy Binary mode)
Default IP address is 192.168.1.21
Other (standby) BUC IP address is 192.168.1.22
IP gateway address is 192.168.1.1
B: SIDE IBUC G
RS485 Data Rate is 9600 baud
RS485/FSK Mode is 1 (Legacy Binary mode)
Default IP address is 192.168.1.22
Other (standby) BUC IP address is 192.168.1.21
IP gateway address is 192.168.1.1
Note: RS485/FSK Mode 1 is the default setting to enable compatible modems to use the
"Legacy Binary" mode to communicate with the IBUC G.
General
You can communicate with the redundant system via any of the following five
interfaces: TCP/IP, RS232, RS485, hand-held terminal (HHT), and FSK link. FSK is
delivered to the interface module from the modem via the J2 connector. The FSK link
uses FSK signals between the IBUC G and modem that are multiplexed on the IFL
coaxial cable.
Note: Use only the J8, J9, or J10 connectors when attempting to communicate with the
IBUC G.
• The J8 connector (labelled User Interface – Ethernet) carries TCP/IP.

• The 19-pin J9 connector (labelled User Interface) carries RS232, RS485, the
hand-held terminal, TCP/UIP, and Form-C alarms.
• The J10 connector (labelled Aux Ethernet) carries TCP/IP.
Final Checks | 7-19

TCP/IP
You can communicate with the IBUC G via TCP/IP through Telnet (ASCII) or the
onboard Web server (HTTP). The IBUC G uses a static IP addressing structure and
does not support DHCP. The IBUC G 1+1 system is factory configured as follows:
A: SIDE IBUC G
IP Address 192.168.1.21
Other BUC IP Address 192.168.1.22
Telnet Port 23
B: SIDE IBUC G
IP Address 192.168.1.22
Other BUC IP Address 192.168.1.21
Telnet Port 23
Note: Your computer should have a static IP address on the same subnet as the IBUC G 1+1
system. Using a suitable cable, connect the computer to the J8, J9, or J10 connectors
on the IBUC G 1+1 system.
Telnet
On the host computer, activate a command prompt window. Type
Telnet 192.168.1.21 for the A: side IBUC G or Telnet 192.168.1.22
for the B: side IBUC G and a cursor should appear on the left of the screen. Type the
password command, CPE=1234, and the response will be IBUC>_. Commands can
now be entered to access the IBUC G functionality. For more information, see
Chapter 5, Monitor and Control Features.
Web Server
On the host computer, activate a Web browser window. In the address window, type
http://192.168.1.21 and then press Enter. Within a few seconds, a login screen
appears. Type the password in the dialog box (the default is 1234), and then click
Login. The page that appears is split with the A: side IBUC G on the left side of the

browser window and the B: side IBUC G on the right side of the browser window.
From the Info tab, you can select from the following Web pages:
• Alarm
• Sensor
• Transmit Config
• Interface Config
• System Config
• Alarm Config
• Redundancy Config
• Alarm Log
The Sensor tab enables monitoring of various IBUC G parameters. Alarms are color
coded where solid green indicates OK – no alarms, flashing green indicates that
activity is present, yellow indicates a warning, and red indicates an alarm condition.
The “Configuration” pages provide access for changing factory default settings to suit
specific site or network requirements. Settings take effect only when you click Save
Settings. Note that some changes in configuration will cause a loss of
communication with the host computer. It will then be necessary to make the
corresponding change in the host computer.
For example, to change a unit’s IP address (using the default settings):
1. Navigate to the “Interface Config” page.

2. Change the IP address to something other than 192.168.1.21 (the factory
default).
3. Click Save Settings.
IP address changes take effect immediately.
4. In the host computer Web browser, type the new address and come back in through
the Login page.
RS232
No additional configuration of the IBUC G Tx 1+1 system is required for proper
RS232 operation. To use RS232, you must connect a suitable cable to the J9
connector. Pin assignments for the cable are listed in Table 7.3 on page 7-10. The
RS232 port uses ASCII protocol and a fixed baud rate of 9600 for communication. On
the host computer, set the serial port settings to the following: Baud rate to 9600, data
bits to 8, parity to none, stop bits to 1, and flow control to none. The IBUC G can be
Final Checks | 7-21

accessed using a terminal emulation program on the host computer such as
HyperTerminal. For information about how to connect using HyperTerminal, see
Appendix B, Using HyperTerminal.
The following two examples use the default settings. If it is necessary to reconfigure
these settings, these examples describe the sequence of events:
To configure TCP/IP, set the following:
A: Side IBUC G
CIA=192.168.1.21 // IP Address
CIB=192.168.1.22 // Other IBUC G IP Address
CIG=192.168.1.1 // IP Gateway
CIM=24 // Subnet Mask
CIP=23 // Telnet Port
B: Side IBUC G
CIA=192.168.1.22 // IP Address
CIB=192.168.1.21 // Other IBUC G IP Address
CIG=192.168.1.1 // IP Gateway
CIM=24 // Subnet Mask
CIP=23 // Telnet Port
To configure RS485, set the following:
A: Side IBUC G
C4A=1 // RS485 Address
C4D=20 // RS485 Delay
C4R=9600 // RS485 Baud rate
If ASCII mode is desired type
C4M=0 // RS485 Mode (Not factory default)
If Legacy mode is desired type
C4M=1 // RS485 Mode

B: Side IBUC G
C4A=2 // RS485 Address
C4D=20 // RS485 Delay
C4R=9600 // RS485 Baud rate
If ASCII mode is desired type
C4M=0 // RS485 Mode (Not factory default)
If Legacy mode is desired type
C4M=1 // RS485 Mode
RS485
Communicating with the IBUC G across RS485 can be through ASCII or a
proprietary binary protocol known as Legacy Binary.
ASCII Mode
The default configuration is Legacy Binary mode so you will need to reconfigure the
IBUC G in order to use ASCII mode. ASCII mode can be selected by using any of the
M&C interfaces.
Communication through a terminal emulation program such as HyperTerminal

requires an on-board RS485 card in the host computer. In HyperTerminal, type the
password command: <0001/CPE=1234 for the A: side IBUC G and <0002/
CPE=1234 for the B: side IBUC G, and then press Enter. When the < prompt re-
appears, the IBUC G is ready to accept commands. In the previous example, <0001/
is the address of the IBUC G followed by the desired command.
If an external box is used to convert RS232 to RS485, a terminal emulation program

will not function. These boxes are designed to work with the RTS/CTS lines manually
which a terminal program cannot handle. In these cases, a network management
program is required to handle this handshaking requirement.
Legacy (Binary) Mode

The default setting of the IBUC G is Legacy Binary mode. In this mode, using the
BUCMON program supplied on the Terrasat CD accompanying the unit is the
simplest method to communicate with the IBUC G. Otherwise, a network
management program must be provided.
Hand-held Terminal
No additional configuration of the IBUC G is required to use the hand-held terminal
(HHT). Connect the 19-pin connector of the HHT cable to the the J9 connector and
Final Checks | 7-23

plug the phone jack into the HHT. Once a flashing cursor is seen in the upper left of
the HHT screen, press the decimal key on the HHT four times to activate the HHT.
The login screen will appear. Type the default password of 1234.
Note: Be sure to use the cables as labelled; that is, use the cable labelled “A: side” with the
A: side IBUC G and the cable labelled “B: side” with the B: side IBUC G.
More information about the hand-held terminal menu tree can be found in Appendix
D.
FSK Link
Several brands of modem are capable of communicating with an IBUC G using an
FSK signal multiplexed onto the IF output connector along with the Tx IF signal and
10 MHz reference signal. This enables you to monitor and control the IBUC G from
the front panel of the modem. The IBUC G default configuration is RS485/FSK
Mode 1 (Legacy Binary mode) because all modems currently require this protocol for
FSK links. The IBUC G is also capable of FSK communication using ASCII mode
but requires a modem compatible with this method. Refer to the modem’s
documentation for commands and procedures for FSK communication with the
IBUC G.
Multifunction LEDs
There are 10 LEDs mounted on the Tx 1+1 interface module housing to provide visual
indication of IBUC G status. Figure 7.6 on page 7-25 depicts the locations of the
LEDs.
LED colors and modes are as follows:
Solid Green – No Alarms

Flashing Green – Activity is being reported
Steady Red – Major Alarm is being reported
Note: A solid green light is also used to indicate which IBUC G is the unit that is currently
online.
Alarms are defined in Chapter 5, Monitor and Control Features. Note that certain
alarms are configurable – enabling you to define them as Major or Minor.

Figure 7.6 Multifunction LEDs for a Tx 1+1 System
The 10 LEDs include:
Power – indicates power is supplied to the unit.
Alarm A: – red indicates an alarm is present for the A: side IBUC G. Green indicates
OK.
Activity A: – indicates Ethernet activity on the A: side IBUC G.
Online A: – indicates that the A: side IBUC G is transmitting the Tx signal to the
antenna.
Online B: – indicates that the B: side IBUC G is transmitting the Tx signal to the
antenna.
Activity B: – indicates Ethernet activity on the B: side IBUC G.
Alarm B: – red indicates an alarm is present for the B: side IBUC G. Green indicates
OK.
Activity J8 – indicates Ethernet activity on User Interface port J8.
Activity J9 – indicates M&C activity on User Interface port J9.
Activity Aux – indicates Ethernet activity on the Auxiliary User Interface port J10.
Mechanical Interface
Tx redundant systems are mounted on a mounting plate to facilitate installation. The
interface module, two IBUC Gs, and the Tx RF switch with associated cables and
waveguide are mounted on a single plate. Power supply units are mounted on a similar
Final Checks | 7-25

plate that is meant to be mounted close to the IBUC G system. For outline drawings
of the redundant mounting system, see Appendix G.
Service and Maintenance

The Terrasat redundant systems are self-contained units that require very little
maintenance.
Standard Maintenance
For optimum performance, inspect the mechanics of the system every six months.
Clean the antenna feeds as necessary to keep them clear of obstructions and check the
cables and connectors for signs of wear, damage, or loose connections. Check all fan
intakes and exhausts to ensure that they are free and clear of debris. Ensure that all
cables have adequate slack.
Fault Isolation
Transceiver Fault Isolation
The information contained in this section should suffice in determining whether a
Terrasat redundant system is faulty. The intent is to determine a “GO” or “NO GO”
situation based on alarms indicated through the M&C ports, as well as measuring
certain signals using test equipment.
AC Power Problems/Conditioning
In today's electrical environment there are many types of power-related problems that
prevent proper operation of sensitive electronic equipment. These noise problems or
disturbances can be caused by such things as voltage induced by lightning, the
switching on/off of high-power electrical equipment, or utility company actions such
as power factor correction. Serious problems can arise with the occurrence of
transients and spikes causing random errors, or even failure of the circuitry. Whatever
the origin of the transients, they can be classified in two categories:
• COMMON-MODE NOISE: The noise voltage that appears is present on both the
active and neutral wires and is measured with respect to ground.
• NORMAL-MODE NOISE: The noise which can be measured between the active
and neutral wire. It is sometimes referred to as differential-mode or
transverse-mode noise.

Category A
At the wall outlets (and more than 30 ft from a distribution panel), the typical noise is
a 0.5 microsecond rise time up to 6 kV peak, open circuit voltage 100 kHz ring wave
with 200 ampere short circuit current capability.
Category B
At the distribution panel, equipment can experience the 100 kHz ringwave but with
500 ampere current capability and a unidirectional impulse up to 6 kV potential rising
in 1.2 s and decaying to half voltage in 50 s. Accompanying this can be a short
circuit current up to 3000 amperes rising to peak in 8 s and decaying to half value in
20s.
To ensure uninterrupted service, Terrasat recommends the use of a line conditioner

and/or UPS based on the expected AC power at the site.
Site-Related Problems
VSAT antennas are often fitted on top of buildings. Avoid close proximity to elevator
motors, etc. Also ensure that the satellite signal path is free and clear of obstructions.
M&C Checks
When troubleshooting redundant systems, the first level of troubleshooting should be
to check the status through the M&C ports. Alarms and an alarm history are available.
Refer to this chapter for specific information when using the RS232, RS485, Ethernet,
or hand-held terminal ports.
Transmit Power Setting

There have been several cases where the transmit power has been turned up to or near
saturation while transmitting a digital carrier. This most likely will result in spectral
distortion, re-growth, and intermodulation products for multi-carrier operation.
When transmitting digital carriers, it is customary to operate the power amplifier

system with an output back off (OBO) sufficient to meet the spectral density mask
requirements and the interference requirements of multi-carrier operation.
Tx IF Input Level Verification

If low or no Tx output power is detected, start the troubleshooting by checking the
input to the Tx Redundant System. Use the following procedure:
1. Check the Tx Input Level displayed in any of the IBUC G M&C interfaces or
disconnect the cable at the IBUC G J2 (Tx L-band) and use a spectrum analyzer to
measure the power level of the L-band signal at the output of the coaxial cable that
Service and Maintenance | 7-27

connects to the IBUC Gs at J2 (Tx L-band). The L-band signal level should be
between -20 dBm and -55 dBm. If it is not, check the cable and modem output.
2. If the L-band signal is good, check that the 10 MHz reference signal is between
+5 dBm and -12 dBm and is free of distortion. If it is not, check the cable and
modem output (or IFU Tx Output).
3. If the L-band and 10 MHz signals are good, proceed to the “Tx Redundancy
Output Verification” check.
Tx Redundancy Output Verification

This check assumes that the L-band and 10 MHz inputs are at the correct levels.
1. Tx Output level is monitored and displayed in any of the IBUC G M&C

interfaces.
Alternately, you may connect a cross coupler and a high-power termination to the
Tx waveguide output.
2. Measure the Tx RF output with the spectrum analyzer connected at the waveguide
output. Ensure that the cable loss of the cable being used for the measurement has
been taken into account.
3. The RF power should be between rated power and rated power –25 dB. If it is not,
the IBUC G is defective and should be returned to the factory for repair.
The Terrasat Repair Policy on page 6-7 has information about returning a defective
unit to the factory.
4. If the IBUC G Tx RF output measures good, check the waveguide, feedhorn, and
antenna for proper operation.
Common Problems
The following common problems or occurrences have been noted during normal
troubleshooting:
• Supply voltage at IBUC G is low or missing

• 10 MHz reference at the IBUC G is at the wrong level or missing
• 10 MHz phase noise does not meet the minimum requirements
• Antenna is misaligned
• Bad OMT and/or antenna
• Damaged cables
• Antenna on the wrong satellite

• Tx L-band input level is misadjusted or turned off
• Water in the IBUC G due to no gasket in the waveguide or a hole in the feed
window.
• Water in the coaxial connectors
• Incorrect frequency settings
M&C Functions
The Tx and Rx redundant systems are designed to provide an interface for user
configuration and control of the systems. In the Tx system, the IBUC Gs monitor
status can initiate switching when required. The unit on the B: side can be commanded
to clone itself to the unit on the A: side. This ensures that the B: side IBUC G is
configured identically to the A: side IBUC G. M&C features are available via the
interface module enabling a single point of control for both IBUC Gs. Commands and
alarms unique to the redundant system are built in to the IBUC G M&C software.
The interface module includes an Ethernet hub to enable users to monitor and control
both IBUC Gs in TCP/IP with a single Ethernet connection and cable.
For remote operation, the redundant systems are equipped with a Monitor and Control
function. The M&C function includes an FSK modem interface, an RS232 interface,
an RS485 interface, a hand-held terminal, an Ethernet interface, multifunction LEDs,
and two alarm relay closures (Form-C): one for the A:_side IBUC G and one for the
B: side IBUC G.
User Interfaces
• Tx and Rx Systems A bank of LEDs provide visual indications of Tx 1+1 and Rx
1+1 status.
• Hand-held Terminal (HHT) An optional item that can be used to access the Tx
and Rx Systems for local M&C via ports J4 (the A: side IBUC G) and J6 (the
B: side IBUC G) for Tx Systems and port J1 for Rx Systems. The HHT has a
4-row x 20-column display with four function keys (F1-F4), a numeric keypad
(0-9), and YES, NO, BKSP (backspace), SPACE, and ENTER keys. Initiate the
HHT session by typing “. . . .” (4 dots), followed by the password. The default
password is 1234. Figure 7.7 depicts the HHT.
The HHT menu consists of a main menu with multiple submenus. Access the
submenus by entering the corresponding digit displayed on the HHT display. To
maneuver back to the previous screen, press the BKSP (backspace) key. Some
screens (for example, INFO) only display information whereas other screens
require user input. User input fields are reflected by the corresponding digit and a
colon (such as 0:) as shown in the HHT Menu Tree on page D-3 for Tx systems.

F1 F2 F3 F4
1 2 3 YES
4 5 6 NO
7 8 9 BKSP
. 0 SPACE ENTER
Figure 7.7 Hand-Held Terminal
• FSK FSK is multiplexed onto the IF cable by means of an FSK-modulated signal.

FSK for redundancy commands operates only in ASCII mode. For more
information about commands and values available in ASCII mode for Tx
redundant systems, see Appendix F . FSK and RS485 are tied together by the
mode of operation (Legacy Binary or ASCII). Once the mode is selected, both will
work in the same mode.
For more information about FSK specifications, see Chapter 5.
• RS485 Two-wire half duplex which is on a separate cable. There are two modes of
operation for RS485 interface: ASCII mode and Legacy Binary mode. Commands
for redundant systems are available only in ASCII mode.

RS485 in ASCII Mode
The RS485 interface is a standard two-wire interface (DATA+, DATA-). The baud
rate is programmable to 1200, 2400, 4800, 9600, 19200, 38400, 57600 or 115200
baud. The data is transmitted asynchronously at 8 bits, no parity, 1 stop bit.
Basic protocol:
Start of Packet: < (ASCII code 60; 1 character)

Target Address: (4 characters)
Address De-limiter: / (ASCII code 47; 1 character)
Instruction code: (3 characters)
Code qualifier: = (ASCII code 61 or 63; 1 character)
Optional arguments: (n characters)
End of Packet: Carriage Return (ASCII code 13; 1 character)
Example: <0001/CPE=1234{CR}
Commands and values available in ASCII mode for Tx Redundant Systems can be
found in Appendix F.
TCP/IP via Ethernet Cable

The Ethernet port is a highly integrated Ethernet Controller which offers an
NE2000-compatible adapter with full-duplex and power-down features. The
full-duplex function enables simultaneous transmission and reception on the
twisted-pair link to a full-duplex Ethernet switching hub. The Ethernet interface is
connected through an isolation transformer and filter.
For the Ethernet interface, the packet is encapsulated in several layers (TCP segment
inside of an IP datagram inside of an Ethernet frame). The Ethernet MAC address is
preset at the factory – each IBUC G has a unique MAC address. The IP address,
network mask, default route, DNS server, and TCP listen port are configurable
through the hand-held terminal interface. The IBUC G controller does not support
DHCP.
The command set for Tx Redundant Systems RS232, RS485, FSK, TCP/IP and
hand-held terminal is provided in Appendix F.
• M&C using TCP/IP is displayed in embedded Web pages. Users connect to the
redundant system M&C and type one of the IBUC G IP addresses through a Web
browser (for Tx Redundancy). After login, you have a choice of Web pages with
monitoring, control, and alarm information. For Tx redundant systems, the screen

splits in half with information for both the A: side IBUC G and the B: side
IBUC G.
Repair Policy
Terrasat transmit redundant systems are not repairable in the field.
In the event that a failure has been detected, it may be necessary to return the defective
unit to the factory. Terrasat’s Repair Policy on page 6-7 has instructions for returning
a defective unit to the factory.

A PPENDIX
PART NUMBERING SCHEMA

CHAPTER 7
A
The charts in this appendix illustrate the part numbering schema used for Terrasat
Communications, Inc. products.
Identifying the Part and Serial Numbers

Figure A.1 illustrates the difference between the unit’s part number and serial number.
Serial Number
Part Number
Figure A.1 Identifying the Part and Serial Numbers

IBR –
FREQUENCY SPECTRAL IF INPUT OPERATING POWER LEVEL/ Tx OUTPUT COLOR SPECIAL SPECIAL
BAND INVERSION CONNECTOR VOLTAGE TYPE OPTIONS OPTIONS OPTIONS SPECS
057064 C-band 6 0 Non-inverting/ F F-type Connector 2 Floating 24 VDC/ 004 – 4 Watt GaAs A Waveguide to
External 10 MHz power via coax N-type Adapter
058064 Standard C-band N N-type Connector 005 – 5 Watt GaAs
1 Inverting/ 3 Floating 24 VDC/ N N-type
058066 Extended C-band External 10 MHz T TNC Connector No power via coax 008 – 8 Watt GaAs
W Waveguide
2 Non-inverting/ 4 Floating 48 VDC/ 010 – 10 Watt GaAs
058067 Full C-band
Internal 10 MHz power via coax
012 – 12 Watt GaAs
064067 Palapa C-band
3 Inverting/ 5 Floating 48 VDC/
Internal 10 MHz No power via coax 015 – 15 Watt GaAs
067070 Insat C-band
A AC Input  016 – 16 Watt GaAs
079084 X-band Standard Connector
127132 Low Ku-band B AC Input 
MilSpec Connector 025 – 25 Watt GaAs
128133 Ku-band 4
137145 Full Ku-band
140145 Standard Ku-band
173181 DBS-band 1
181184 DBS-band 2
295300 Ka-band 1 100 – 100 Watt GaAs
300310 Ka-band 2 125 – 125 Watt GaAs
290300 Ka-band 3 150 – 150 Watt GaAs
151 – 150 Watt GaN
201 – 200 Watt GaN
401 – 400 Watt GaN
Figure A.2 Part Numbering Schema for IBUC Gs, IBUC 2s, and IBRs
A-2 | Part Numbering Schema

IBUC –
FREQUENCY SPECTRAL OPERATING POWER LEVEL/ INPUT/ OUTPUT COLOR SPECIAL
BAND INVERSION VOLTAGE TYPE/FAMILY OPTIONS OPTIONS OPTIONS
057064 Low C-band 6 0 Non-inverting 24 24 VDC 004 Watt Ku-band
058064 Standard C-band 1 Inverting 47 48 VDC (Floating ) 005 Watt C/X/DBS/Ka-band
058066 Extended C-band 48 48 VDC 008 Watt Ku/DBS-band
058067 Full C-band 49 –48 VDC 010 Watt C/X/Ka-band
064067 Palapa C-band A AC Input 012 Watt Ku/DBS-band
067070 Insat C-band 015 Watt C-band
079084 X-band 016 Watt Ku/DBS/Ka-band
127132 Low Ku-band 020 Watt C/X/Ku/DBS/Ka-band
128133 Low Ku-band 4 025 Watt C/X/Ku/DBS/Ka-band
137145 Full Ku-band 030 Watt C/Ku-band
140145 Standard Ku-band 040 Watt C/X/Ku/Ka-band
148145 High Ku-band 050 Watt C/X/Ku-band
173181 DBS-band 1 060 Watt C/X/Ku-band
181184 DBS-band 2 080 Watt C/X/Ku-band
295300 Ka-band 1 100 Watt C/X/Ku-band
300310 Ka-band 2 125 Watt C/X-band
290300 Ka-band 3 150 Watt C/X-band
175 Watt C/X-band
200 Watt C-band
Figure A.3 Part Numbering Schema for IBUCs
Identifying the Part and Serial Numbers | A-3

305 – –
FREQUENCY CABLE SWITCH CABLE POWER SUPPLY COLOR
BAND TYPE OPTIONS OPTIONS MTG KIT OPTIONS OPTIONS
21027 C-band (Gen 2) IBUC
21028 Ku-band (Gen 2) IBUC
21029 X-band (Gen 2) IBUC
21128 C-band HP IBUC
21321 Ku-band HP IBUC
21797 X-band HP IBUC
21808 Ka-band IBUC 2
22074 Ku-band IBUC 2
22075 C-band IBUC 2
22076 X-band IBUC 2
22077 Ka-band IBUC 2
22085 DBS-band IBUC 2
22191 C-band IBUC G
Figure A.4 Part Numbering Schema for Transmit Redundant (Tx 1+1) Systems

305 – –
FREQUENCY PLATE DC CABLE L-BAND and SWITCH SPECIAL

BAND OPTIONS OPTIONS CABLE OPTIONS OPTIONS
10712 C-band
10713 Ku-band
10714 X-band
Figure A.5 Part Numbering Schema for Receive Redundant (Rx 1+1) Systems

PSUI – –
POWER OUTPUT POWER COLOR SPECIAL
SUPPLY VOLTAGE OPTIONS OPTIONS OPTIONS
9 Outdoor 24 24 VDC Output
11 600 Watt Indoor 48 48 VDC Output
12 1000 Watt Indoor
Figure A.6 Part Numbering Schema for IBUC with PSUI Systems

IFU – –
10 MHz REFERENCE IBUC Tx MODEM Rx MODEM EXTERNAL INPUT

SIGNAL Tx POWER SUPPLY CONNECTOR CONNECTOR REFERENCE VOLTAGE
X N/A X N/A N Plug X Plug X Plug
I Internal 2 Internal 24 VDC S SMA (f) N Type-N (f) S SMA (f)
E External 4 External 48 VDC F BNC (f) S Type SMA (f) B BNC (f)
M From the Modem M From the Modem F Type-F (f)
10 MHz REFERENCE LNB Rx LNB SPECIAL

SIGNAL Rx POWER SUPPLY Tx CONNECTOR CONNECTOR OPTIONS
X N/A X N/A N Plug X Plug
I Internal 2 Internal 24 VDC S SMA (f) N Type-N (f)
E External M From the Modem F BNC (f) S Type SMA (f)
M From the Modem F Type-F (f)
Figure A.7 Part Numbering Schema for IFU Systems

MDC – –
FREQUENCY LNB NOISE CONNECTOR 10 MHz
BAND TEMPERATURE TYPE REFERENCE STABILITY
036052 Standard C-band 15 15° K C-band F Type-F External
034042 Palapa C-band 20 20° K C-band N Type-N i Internal
045048 Insat C-band 35 35° K C-band
109117 Low Ku-band 50 50° K Ku-band
117122 Mid Ku-band 60 60° K Ku-band
122127 High Ku-band
Figure A.8 Part Numbering Schema for LNBs

SSPA –
FREQUENCY OPERATING INPUT/OUTPUT COLOR SPECIAL
VOLTAGE POWER OPTIONS OPTIONS OPTIONS
BAND LEVEL
058064 Standard C-band 47 48 VDC
040 Watt (Ku-band)
(Floating)
058066 Extended C-band 050 Watt (C/X/Ku-band)
48 +48 VDC
058067 Full C-band 060 Watt (C/X/Ku-band)
49 -48 VDC
064067 Palapa C-band 080 Watt (C/X/Ku-band)
AC AC Input
067070 Insat C-band 100 Watt (C/X-band)
079084 X-band 125 Watt (C/X-band)
137145 Full Ku-band 150 Watt (C/X-band)
140145 Standard Ku-band 175 Watt (C/X-band)
200 Watt (C-band)
Figure A.9 Part Numbering Schema for SSPAs

305 –
FREQUENCY SSPA CABLE SWITCH CABLE POWER SUPPLY COLOR

BAND TYPE OPTIONS OPTIONS MTG KIT OPTIONS OPTIONS
21657 C-band
21658 X-band
21659 Ku-band
21660 C-band HP
21661 X-band HP
21662 Ku-band HP
Figure A.10 Part Numbering Schema for Redundant SSPA 1+1 Systems

A PPENDIX
B
USING HYPERTERMINAL
CHAPTER 7
This appendix describes how to use an RS232 connection and HyperTerminal to

communicate with the IBUC.
Establishing a HyperTerminal Session

To communicate with the IBUC using an RS232 connection and HyperTerminal,
1. Connect a cable to a serial port of a PC and the M&C connector of the IBUC.
Refer to the fabrication drawing (FBD-210121A.pdf) in Figure G.1 on page G-2 for
information about making a 19-in to DB9F cable.
2. From the Windows Start menu, choose Start → All Programs → Accessories →
Communications → HyperTerminal.
A HyperTerminal window with a New Connection Description window appears, as
shown in Figure B.1. By following the prompts, you can establish the settings for
your session and then save them for future use.
Figure B.1 New Connection Description Window
3. Type a name for the connection and click an icon to select it, and then click OK.
In this example, the connection is named “test2”.
B-2 | Using HyperTerminal

4. The Connect To dialog box appears. See Figure B.2.
Figure B.2 Connect To Window

5. From the Connect Using drop-down menu, choose the COM port where RS232 is
connected (in this example, it is COM1), and then click OK.
The COM1 Properties Window shown in Figure B.3 appears.
Establishing a HyperTerminal Session | B-3

Figure B.3 COM1 Properties Window
6. In the Port Settings dialog box, choose the following options
• Bits per second: 9600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
7. Click Apply, and then click OK to save the settings.
8. In the HyperTerminal window, a blinking cursor indicates that the session is now
active.
Test the connection by pressing Enter. You should receive an “error=Please enter
valid password” message and the IBUC> prompt as shown in Figure B.4.
Note: The format of the responses will vary according to whether the message response
mode is set to verbose (the default) or terse. The figures in this document show
verbose mode (indicated by the IBUC> prompt). In verbose mode, the output is
formatted for easier viewing To change to terse mode, type C4V=0 at the command
line. To return to verbose mode, type C4V=1 at the command line.

Figure B.4 Invalid Password Error Message
9. From the menu bar, choose File → Properties → Settings. Click on the Settings
tab, and then click ASCII Setup. See Figure B.5.
Figure B.5 ASCII Setup Window

10. In the ASCII Setup window, select the following options:
• ASCII Sending
- Send line ends with line feeds
- Echo typed character locally
Establishing a HyperTerminal Session | B-5

• ASCII Receiving
- Wrap lines that exceed terminal width
11. Click OK to save the settings and to close the ASCII Setup dialog box.
12. Click OK to save the new Properties.
The properties window closes and there is a blank HyperTerminal window with a
blinking cursor.
13. At the IBUC> prompt, type CPE=1234 and press Enter. This command logs you
in to the IBUC.
If you have changed the password from the default 1234, type that password
instead.
14. Your login was successful if you receive a blinking prompt in the HyperTerminal
window. If you receive an “Error=invalid value” message such as the one in
Figure B.6, your login was not successful. Check the password value and try
again.
Figure B.6 Invalid Value Error Message

15. The IBUC is now ready to accept commands. An example session begins with
Step 16.
16. Type COI and then press Enter.
This command displays general information about the IBUC such as the serial
number and firmware version level.
17. Type CIA and then press Enter.
This command displays the IP address of the unit.
18. Type CIM and then press Enter.
This command displays the IP netmask.
19. Type CIG and then press Enter.
This command displays the IP Gateway address of the unit.
20. Type CIP and then press Enter.
This command displays the TCP port used for Telnet communications.

Your screen should resemble the one shown in Figure B.7.
Figure B.7 Active HyperTerminal Window

21. To end the HyperTerminal session, choose File → Exit.
The system will prompt you to confirm that you want to end the session. If this is
correct, click Yes. If not, click No.
22. If you clicked Yes to end the session, the system will prompt you about saving the
session settings you input beginning with Step 3. Click Yes to save the named
connection.
The HyperTerminal session is now complete.
Using a Saved Connection

To begin a new HyperTerminal session using a named connection,
1. From the Windows Start menu, choose Start → All Programs → Accessories →
Communications → HyperTerminal.
A blank New Connection window with a Connection Description window (similar
to Figure B.1 on page B-2) appears.
2. Click Cancel when prompted to type a name and to choose an icon for the
connection.
3. From the menu bar, choose File → Open.
Using a Saved Connection | B-7

A list of previously saved HyperTerminal names appears.
4. Click the connection name you want to use, and then click Open.
A blank HyperTerminal window with the previously saved settings appears.
5. Type CPE=1234 to log into the IBUC.
(Note: If the password has been changed, use that value instead of the default
1234.)
You can now enter ASCII commands at the prompt.
Note: When you create a named connection and then save it, that connection name will also
appear as an option when you choose Start → All Programs → Accessories →
Communications → HyperTerminal → <Named Connection>. Click the name to
access your saved connection settings.
Ending a HyperTerminal Session

To end the HyperTerminal session,
• Choose File → Exit.

A PPENDIX
IBUC G WEB PAGES

CHAPTER 0
C
The embedded Web pages shown in this appendix are a user-friendly way to access
the various monitor and control (M&C) features offered by the IBUC G.
Most of the screen shots from the Web interface shown in this appendix are from a
transmit redundant (Tx 1+1) system. The main data area below the tabs is split into
two identical windows for the A: side IBUC G and the B: side IBUC G. In a single
IBUC G system, only a single data window is displayed.
Introduction
To access the embedded Web pages,
1. Connect the host computer to the IBUC G.

• When using a single IBUC G, connect a TCP/IP cable to J4 connector on the
IBUC G.
• When using a Tx 1+1 redundant system, connect a TCP/IP cable to the 19-pin
J4 connector.
2. Choose “Start,” and then “Control Panel”.
3. Choose “Network Connections”.
4. Choose “Local Area Connection”.
The Local Area Connection Status window shown in Figure C.1 appears.
Figure C.1 Choosing Network Connections
5. Click Properties.
The window shown in Figure C.2 appears.
C-2 | IBUC G Web Pages

Figure C.2 Choosing the Internet Protocol (TCP/IP) Properties
6. In the dialog window, scroll down until “Internet Protocol (TCP/IP)” becomes
visible.
7. Select “Internet Protocol (TCP/IP).”
As shown in Figure C.2, it will become highlighted once you select it.
8. Click Properties.
The window shown in Figure C.3 appears.
Figure C.3 Typing the IP Address

9. Select “Use the following IP address,” and then type an IP address.
This IP address cannot be the same address as the IBUC G. In Figure C.3,
192.168.1.100 is an example, assuming that the IBUC G is using its default IP
address (192.168.1.21).
10. Click OK.
The error message shown in Figure C.4 appears.
Introduction | C-3
Figure C.4 Invalid Subnet Mask Error Message
11. Click OK.
This causes the “Subnet Mask” fields to be filled in with the default subnet mask
address.
12. Click OK.
13. Using the host computer, activate a Web browser window.
14. Type the IP address of the IBUC G in the address window, and then click Enter.
The IP address of the IBUC G was assigned at the factory and is shown in the test
data that accompanies the unit.
• In a single IBUC G, the factory default IP address is
http://192.168.1.21
• In a Tx 1+1 system, the factory default IP address for the A: side IBUC G is
The factory default IP address for the B: side IBUC G is 
Note: Your computer should have a static IP address on the same subnet as the Rx 1+1
system.
15. Within a few seconds, the Login page shown in Figure C.5 on page C-5 will
appear.

Screen Shots
Login
This page appears to prompt you to login to the system. You can login or logout from
any of the tabs shown in Figure C.5.
Type your password in the dialog box, and then click Login. The default value is
1234. If the login password that you entered is accepted, the page of the highlighted
tab appears. In Figure C.5, the Info tab is highlighted; thus, the Info tab will appear
upon successful login. If the login password entered is incorrect, the screen remains
unchanged.
Figure C.5 Login
Screen Shots | C-5

Information Tab
Use this tab to view read-only IBUC G data such as the model number, serial number,
revisions, and frequencies.
Figure C.6 Information Tab
From this page, you can view the following parameters:
• Model Number
Displays the model number of the IBUC G(s). More information about the data
contained within the part number is found in Appendix A.
• Serial Number
Displays the unique serial number of the IBUC G(s).
• Firmware Version
Displays the version number. The firmware version number of the IBUC G is
used mainly by Terrasat Technical Support personnel.
• Hardware Version
Displays the version number of the hardware.

Note: The hardware version can be updated only when the IBUC G is returned to the
factory.
• Power Class
Displays transmitter output power at 1 dB compression. Power class information is
contained within the part number. More information about locating the power level
of the IBUC G is found in Appendix A.
• Frequency Band
Displays the standard name of the band.
• RF Frequency Range
Displays the valid RF frequencies for the IBUC G(s). The RF Frequency range for
each of the various bands is listed in Table 2.1 on page 2-3.
• IF Frequency Range
Displays the valid IF frequencies for the IBUC G(s). The L-band IF Frequency
range for each of the various bands is listed in Table 2.1 on page 2-3.
• LO Frequency
Displays the valid LO frequencies for the IBUC G(s). The LO Frequency for each
of the various bands is listed in Table 2.1 on page 2-3.
• Band Inversion
Options include:
• Non-Inverted
• Inverted
When inverted, the relationship between the RF and IF frequencies is inverse;
that is, as the RF Frequency increases, the lower the IF Frequency from the
modem must be.
• Supply Voltage Range
Displays the power supply voltage range for which the IBUC G was designed.
The Supply Voltage Range is based on the configuration of your IBUC G(s).
• Total System Hours
Displays the total number of hours that the system has been operating (that is, the
total number of hours that the system has been powered on).
• Total Tx Enabled Hours
Displays the total number of hours that the transmitter has been enabled (that is,
the with transmit = On and mute = Off).
Screen Shots | C-7

Alarm Tab
Use this tab to verify the alarm status of the unit. Alarm status is indicated with color
and text: a green background indicates that that parameter is operating within
specifications and no faults have occurred, a yellow background indicates a minor
fault, and a red background indicates a major fault. A white background indicates that
particular parameter is not available for monitoring. Table C.1 on page C-15 contains
the default configuration and lists which alarms are available for user configuration.
For information about how to configure these alarms, see the Alarm Configuration
Tab on page C-24.
Figure C.7 Alarm Status Tab
• Tx Output
Indicates whether the IBUC G is currently transmitting. Options include:
• On
• Disabled
• Muted (Alarm)

• Tx Output Low
Indicates whether the Tx Output level is operating below a minimum threshold.
Options include:
• OK
• Major
• Minor
• Tx Output High
Indicates whether the Tx Output level is operating above a maximum threshold.
Options include:
• OK
• Major
• Minor
• Tx Input Low
Indicates whether the Tx Input level is operating below a minimum threshold.
Options include:
• OK
• Major
• Minor
• Tx Input High
Indicates whether the Tx Input level is operating above a maximum threshold.
Options include:
• OK
• Major
• Minor
• Simulated Alarm
Indicates whether a simulated alarm has been issued. A simulated alarm is mainly
used for testing. Options include:
• OK
• Major
• Temperature (Internal)
Indicates that the internal temperature of the IBUC G exceeds 85 °C.
Screen Shots | C-9

Note: If the High Temperature Shutdown alarm has been enabled and the internal
temperature of the IBUC G exceeds 85 °C, the IBUC G will shut down
automatically.
• ALC Range
Indicates that the Tx Output level is being kept constant by the automatic level
control (ALC) function. Options include:
• OK
• Out of Range
This alarm occurs whenever the gain reaches or exceeds ±8 dB.
• N/A
Note: An alarm occurs when the IBUC G can no longer maintain the Tx Output level.
This alarm is coded into the IBUC G and is not available for user configuration.
• AGC Range
Indicates that the automatic gain control function is unable to maintain the gain
level.
• 10 MHz Source
Indicates whether the source of the 10 MHz reference signal is internal or external.
Note: For IBUC Gs operating with only an external 10 MHz reference signal, this field
is labelled “10 MHz Detector” and the options include:
• OK (indicates that the 10 Mhz signal is functioning properly)
• Low (indicates that the 10 MHz signal is low or missing)
• PLDRO Lock
Indicates whether the phase-locked dielectric resonator oscillator (PLDRO)
frequency is locked (or stable). When the PLDRO is out-of-lock, this alarm causes
the muting of the amplifier and automatically shuts down the IBUC G. Options
include:
• OK (indicates that the PLDRO is locked and functioning properly)
• Major
Note: This alarm is always a major alarm and is not available for user configuration.
• Switch Fault
Indicates whether the waveguide switch is operating properly. This alarm is coded
into the IBUC G and is not available for user configuration. Options include:
• OK (indicates that the PLDRO is locked and functioning properly)
• Major

Note: This alarm is only available for redundant systems. It does not appear on the Alarm
Status tab for single IBUC G systems.
Screen Shots | C-11

Sensor Tab
Use this tab to view real-time voltage, current, and power levels for the IBUC G.
Figure C.8 Sensor Tab
• Supply Voltage
Displays the voltage reading of AC-powered IBUC Gs is displayed in VAC.
Valid values depend on the IBUC G model. The readings on this page should fall
within the range listed on the Information Tab on page C-6.
• Current Consumption
Displays the current draw at the input in amps.
• Power Consumption
Displays the power consumption of the IBUC G in VA.
• Tx Input Level
Displays the Tx Input level in dBm.
• Tx Output Level
Displays the Tx Output level in dBm.

• Internal Temperature
Displays the real-time internal temperature of the IBUC G in °C.
Note: If the High Temperature Shutdown alarm has been enabled and the internal
temperature of the IBUC G exceeds 85 °C, the IBUC G will shut down
automatically.
• DRO Tuning Voltage
Displays the tuning voltage for the DRO in volts. This voltage is not static and is
continually monitored. The valid range is 1 to 9 volts; ideally, the DRO tuning
voltage should fall within the range of 2 to 8 volts when the DRO is locked.
If your readings consistently fall within the range of 1 to 2 volts or 8 to 9 volts,
contact Terrasat Technical Support.
Screen Shots | C-13

Transmit Configuration Tab
Use this tab to configure transmission operating parameters for the IBUC G. Click
Save Settings when you have completed entering data to ensure that your changes
are saved and then implemented.
Figure C.9 Tx Configuration Tab
From this page you can configure the following parameters:
• Tx Output
Select whether the unit is actively transmitting. Options include:
• Enable
• Disable
• Power Monitor Frequency
Sets the Power Monitor Frequency which is the actual frequency at which you are
operating. To ensure accurate readings, you must set your operating frequency
which might be different from the factory default values listed in Table C.1.
Example: If the frequency allocated to you by the satellite carrier is 6400 MHz,
set the Power Monitor Frequency to 6400 MHz.

The factory default values in Table C.1 are listed according to the model number
of the IBUC G. For more information about identifying the model number of the
IBUC G, see Appendix A.
Table C.1 Default Values for Power Monitor Frequency
Model Default
Number Value
057064 6075
058064 6137
058066 6250
058067 6287
064067 6575
067070 6875
079084 8150
127132 13000
128133 13050
137142 14000
137145 14125
140145 14250
173181 17700
181184 18250
290300 29500
295300 29750
300310 30500
• Tx State at Powerup
Sets whether the unit is transmitting upon powerup. Options include:
• Enable
• Disable
• Tx Powerup Delay
Sets the transmit power output delay of the IBUC G in seconds. When configured,
the Tx Output will be muted for the time period specified before beginning to
transmit.
Screen Shots | C-15

• Power Read Mode
Sets the mode in which power is read. Options include:
• Burst
In burst mode, the signal is active only a small percentage of the time because
packets of data are sent in bursts.
• Continuous
In continuous mode, the signal continues without interruption.
• Burst Threshold
Sets the burst threshold for the IBUC G. This value determines the level at which
a burst is considered valid. The threshold is for the output power level; the
threshold for input power is configured internally.
The value must be between rated power and no less than 2 dB below rated power.
Default values are listed in Table C.2.
Table C.2 Default Values for the Burst Threshold
Power Default
Level Value
002 13.0
004 16.0
005 17.0
008 19.0
010 20.0
012 21.0
016 22.0
020 23.0
025 24.0
030 25.0
040 26.0
050 27.0
060 28.0
080 29.0
100 30.0
125 31.0
150 32.0

Table C.2 Default Values for the Burst Threshold (Continued)
Power Default
Level Value
175 32.4
200 33.0
400 36.0
• Burst Count
Sets the burst count of the IBUC G.
• Gain Mode
Options include:
• Open is the gain obtained when there is no feedback in the measuring loop.
Keep in mind that the open-loop gain is affected by temperature and
frequency; however, the temperature compensation feature is still active when
the unit operates with open-loop gain. Open is the default setting.
• Automatic Gain Control (AGC)
• Automatic Level Control (ALC)
• Attenuation
Type a value within the range of 0.0 dB to 16.0 dB in 0.1 dB steps. After you click
Save Settings, the gain of the unit will be reduced by that value.
• The default setting is 0.0 dB
• Tx Input Threshold Low
Sets the lowest permitted transmit input value down to -60 dBm. You will receive
an error message if you try to exceed the threshold range. Click OK to return to the
Tx Config page to enter a valid value.
• Tx Input Threshold High
Sets the highest permitted transmit input value up to -15 dBm. You will receive an
error message if you try to exceed the threshold range. Click OK to return to the
Tx Config page to enter a valid value.
• Tx Output Threshold Low
Sets the lowest permitted transmit input value down to (rated PSAT - 20 dB). You
will receive an error message if you try to exceed the threshold range. Click OK to
return to the Tx Config page to enter a valid value.
Screen Shots | C-17

• Tx Output Threshold High
Sets the highest permitted transmit input value up to (rated PSAT + 1 dB). You will
receive an error message if you try to exceed the threshold range. Click OK to
return to the Tx Config page to enter a valid value.
• Current Gain Control
This option is always greyed-out (unavailable). The Gain Control represents the
current gain of the AGC/ALC voltage variable attenuator (VVA) circuitry. The
Gain Control range is -8.0 dB to 8.0 dB. When the Gain Control Reset option is
selected, this value will reset to 0.0 (midrange).
• Gain Control Reset
Over time, gain control levels can fluctuate. When the Gain Control Reset option
is enabled, the gain control resets to 0.0 (midrange) Options include:
• Select (default)
• Reset
Note: You must choose “Reset” and then click Save Settings in order to reset the
gain control.
• Internal 10 MHz Trim
You can specify a frequency trimming value for IBUC Gs equipped with the
optional internal 10 MHz reference signal
Valid values: 0 – 255
Note: When the IBUC G is operating using an external 10 MHz reference signal, this
field is greyed-out and unavailable for user input.

Interface Configuration Tab
Use this tab to configure the interfaces (TCP/IP or RS485/FSK). You can also specify
SNMP settings. Click Save Settings when you have completed entering data to
ensure that your changes are saved and then implemented.
Figure C.10 Interface Configuration Tab
• IP Address
Valid values range from (but do not include) 1.0.0.0 through 224.0.0.0. When the
netmask is applied, 0 and 225 in the last byte are excluded.
• IP Subnet Mask
Sets the IP netmask.
• Valid values range from 8 through 30 representing the number of ones in the
netmask. This corresponds to 22.0.0.0 to 255.255.255.252.
• Gateway Address
Sets the IP Gateway Address which is the address that the IBUC G will send to if
the requested IP address does not reside on the local LAN segment.
Note: This address cannot be the same as the IP address of the unit.
Screen Shots | C-19

• Telnet Port
Telnet is a network protocol used to establish remote communication. Ports are
specific channels for network services. In the IBUC G, the default Telnet port is
23.
Valid values include port numbers within the range of 1 to 65535.
• Web Server Auto Refresh
Sets the rate in seconds in which the Web page refreshes. The default is 0.
Valid values: 0 to 3600
Note: When set to 0 sec (the factory default), the Web page will not refresh.
• RS485/FSK Address
Sets a unique designator for the unit.
Valid values for Legacy Binary: 1 to 15
Valid values for ASCII: 1 to 254
• RS485 Baud Rate
Sets the baud rate at which data is sent. The default is 9600 baud.
Valid values include: 1200, 2400, 4800, 9600, 38400, 57600, or 115200.
• RS485/FSK Mode
Sets the transmission protocol. Options include:
• ASCII
• Binary Mode (default)
• RS485/FSK Delay
Sets the delay in msec between the end of one transmission and the beginning of
reception in half-duplex mode.
Valid values include 1 to 255. and the default value is 20.
• SNMP Version 1.0
SNMP is a communication protocol used for managing TCP/IP networks. When
enabled, the unit will respond to SNMPv1 requests. Options include:
• Enable (default)
• Disable
• SNMP Traps
Sets the generation of SNMPv1 traps. SNMP traps are one-way messages that are
initiated by a network element to indicate status changes and sent to the network

management system. After receiving the message, the manager displays it and can
choose to take an action based on the event. Options include:
• Disable
• SNMP Host Trap IP
Sets the IP address to which the network management system sends traps.
• SNMP Public Password
The SNMP public password (or community string) is used for requesting
information from the IBUC G. The password cannot exceed 16 alphanumeric
characters.
• SNMP Private Password
The SNMP private password (or community string) is used for making changes to
the IBUC G. The password cannot exceed 16 alphanumeric characters.
• SNMP Trap Password
Sets the password for the trap manager. The password cannot exceed 16
alphanumeric characters.
Note: Changing the SNMP passwords requires a firmware reboot.
Screen Shots | C-21

System Configuration Tab
Use this tab to set the system password and the password timeout. You can also reset
(reboot) the controller card from here. Additionally, you can set the system time here.
Click Save Settings when you have completed entering data to ensure that your
changes are saved and then implemented.
Note: The screen in Figure C.11 appears only when you have a single IBUC G.
Figure C.11 System Configuration Tab
• System Password
To change the system password, type a numerical value between 1 and 65535.
Note: The default password is 1234.
• Password Timeout
Changes the time period during which you can log in to the system. Options
include:
• 0 = No password timeout
• 1 to 65535 = Number of minutes before system timeout

• Verbose Message
Sets whether responses of the serial and TCP connections are terse (for computers
to read) or verbose (for people to read).
• Enabled = Terse
• Disabled = Verbose
• Echo
Sets whether the system responds back to SET commands or remains silent.
Options include:
• Enabled
• Disabled
• Time
Sets the system time of the IBUC G in a mm/dd/yyyy format.
• NCustom Title
Use this 32-character alphanumeric field to create a customized label for each
IBUC G. Use information that will help you to identify the IBUC G (such as
company name, location of each IBUC G, and so on).
• External LED
Sets the state of the multifunction LED indicator. Options include
• Disabled (LED is off)
• Enabled (LED is on)
Enabled is the default setting.
• System Reset
When selected, this causes a momentary muting of the transmitter and should be
used with caution. A dialog box appears and you are asked to confirm your
selection.
• 50 Hz AC Correction
When enabled, applies a 50 Hz correction factor to AC-powered IBUC Gs.
Options include:
• Disabled
• Enabled
Disabled is the default setting.
Screen Shots | C-23

Alarm Configuration Tab
Use this tab to configure alarms as Minor, Major, or None. Major alarms cause a
summary alarm (relay closure) with the Form-C relay. This is particularly important
when operating in redundancy mode where summary alarms will cause switchovers.
You can also configure the alarms as suppressible. Suppressible alarms will be
suppressed only when the “Suppress Faults” option is enabled. Click Save Settings
when you have completed entering data to ensure that your changes are saved and then
implemented.
Figure C.12 Alarm Configuration Tab
From this page you can configure the following alarms:
• Temperature Alarm
Sets the type of alarm produced when the temperature threshold has been
exceeded. Options include:
• Disable
• Minor
• Major
• Tx Input Threshold Low

Sets the type of alarm produced when the lower Tx Input Threshold has been
• Disable
• Minor
• Major
• Tx Input Threshold High
Sets the type of alarm produced when the higher Tx Input Threshold has been
• Disable
• Minor
• Major
• Tx Output Threshold Low
Sets the type of alarm produced when the lower Tx Input Threshold has been
exceeded. The default lower threshold is equal to rated P1dB - 20.
Options include:
• Disable
• Minor
• Major
• Tx Output Threshold High
Sets the type of alarm produced when the higher Tx Input Threshold has been
exceeded. The default higher threshold is equal to rated P1dB+ 1.
Options include:
• Disable
• Minor
• Major
• Temperature Alarm Suppressible
Sets whether the temperature alarm is suppressible. When suppressed (enabled), a
temperature alarm will not appear as an event in the Alarm Log. Options include:
• Disable
• Enable
• Input Threshold Low Suppressible
Sets whether the lower input threshold is suppressible. Options include:
Screen Shots | C-25

• Disable
• Enable
• Output Threshold Low Suppressible
Sets whether the lower output threshold is suppressible. Options include:
• Disable
• Enable
• Output Threshold High Suppressible
Sets whether the higher output threshold is suppressible. Options include:
• Disable
• Enable
• High Temperature Shutdown
Sets whether to shutdown the IBUC G when the internal temperature threshold of
85 °C has been exceeded. The unit must cool down by 20 °C before resuming
transmission. Transmission will resume automatically once the unit has cooled by
20 °C. Options include:
• Disable
• Suppress faults
Sets whether the unit will suppress all alarms that are configured as suppressible.
Options include:
• Disable
• Enable
• Simulate faults
When enabled, a simulated alarm is issued that does not affect transmission status
or traffic. Options include:
• Disable
• Enable
Use this alarm to determine whether your alarm settings are functional. It is most
useful for redundant systems to test whether a major alarm will successfully
trigger a switchover to the standby unit.

Redundancy Configuration Tab
Use this tab to configure redundancy settings for a protected pair of IBUC Gs. Only
the online IBUC G can control the redundancy mode, redundancy switching type, and
auto clone settings. The set IBUC G location, set online IBUC G, and other IBUC G
IP address are set individually. Click Save Settings when you have completed
entering data to ensure that your changes are saved and then implemented.
Figure C.13 Redundancy Configuration Tab
• Set IBUC Location

Specifies the physical location of each IBUC G on the switch. In a redundant
system, there must be an A: side IBUC G and an B: side IBUC G (not two
A: side IBUC Gs nor two B: side IBUC Gs). Options include:
• A
• B
Screen Shots | C-27

• Set Online IBUC
Specifies which IBUC G is online. Options include:
• A
• B
• Redundancy Mode
Sets the redundancy switching mode of operation. When configured for reverting,
the units can switch between each other multiple times when a fault occurs unless
both units are faulted. In nonreverting mode, when the A: side unit faults, a switch
to the B: side unit will occur. However, once operation has switched to the B: side
unit no additional switches will occur without user intervention. This item can be
changed only from the unit designated as Online (Master). Options include:
• Reverting
• Nonreverting
• Redundancy Switching Type
Sets the switching type. Options include
• Automatic
• Manual
Note: In Automatic Mode, if the standby unit is faulty, the online IBUC G will not
switch to the standby unit. However, you can force this switch when in Manual
Mode.
• Auto Clone Settings
Sets the cloning configuration of a redundant pair. When enabled, the settings that
are common to both units are copied from the online IBUC G to the standby
IBUC G. Options include:
• Enable
• Disable
• Other IBUC IP Address
Sets the IP address of the other IBUC G.
• Other IBUC Public IP Address
Sets the public IP address of the other IBUC G. Use this option when the
IBUC Gs are on a network and you need remote access.

Alarm Log Tab
Use this tab to view the alarm history of the IBUC G. When a fault occurs, an entry is
added to the alarm log. Entries are time-stamped to determine the order in which the
alarms occurred. These events can be used to help determine cause during system
troubleshooting.
A total of 40 events are stored by the IBUC G. An event can contain multiple alarms.
In Figure C.14, the events recorded consist of miscellaneous (M) and transmit (T)
alarms. The most recent alarm is the first in the list.
To clear the alarm history, click Clear.
Figure C.14 Alarm Log Tab
Note: The Alarm Log updates every minute but the information displayed updates only
when there is a change from no alarms to an alarm.
Screen Shots | C-29


A PPENDIX
HAND-HELD TERMINAL
CHAPTER 0
D
MENU TREE
Menu Options
Beginning with firmware version 1.00, the structure of the hand-held terminal’s menu
tree and menu options has changed. Figure D.3 on page D-3 illustrates the updated
menu tree and the available options when using the hand-held terminal (HHT). Those
options are described in this appendix.
To enable the HHT,
1. Connect the HHT to the system by using the 19-pin connector.

• When using a single IBUC G, connect the HHT to the system by using the J3
connector.
• When using redundant IBUC Gs, connect the HHT to the system by using the
either the J1 connector (for the A: side IBUC G) or the J8 connector (for the
B: side IBUC G).
2. When the connection is made and the HHT is receiving power, a blinking cursor
appears in the upper left of the HHT display.
3. Type “. . . .” by using the decimal key on the HHT keypad.
The screen now displays the IBUC G model number and serial number which are
shown in Figure D.1, and the system requests a password.
Figure D.1 Sample IBUC G HHT Display
4. Type the password by using the number keys on the HHT.
5. The “Info & Sensors” window shown in Figure D.2 appears.
Figure D.2 Sample IBUC G Info & Sensors Window

6. The unit is now ready to receive input.
Note: The HHT now offers “adaptive learning;” that is, you no longer need to scroll up and
down through all of the menu options during a single session. For example, if a user
repeatedly uses the IP Address and Clear Alarm Log options, after the first time
accessing those options by using the up and down arrow keys to access the submenus,
the user can now use the right and left arrows to move between submenu branches
because the system “learns” to access those two options. You can continue lateral
movement by using the → and ← keys.
There is no need to logout from the HHT when the session is complete. However,
once the HHT is disconnected from the system or the session ends, all of the previous
menu movements are lost.
D-2 | IBUC G Hand-held Terminal Menu Tree

HHT Log In
Info & Sensors Tx Alarm Tx Thresholds Interface SNMP System Redundancy
Tx Power Attenuation View Tx Input Level IP Address SNMP Enable Set Password Set IBUC
Levels Alarms High Location
Tx On/Off View Misc Input Level IP SNMP Trap Password Set Online
Sensors Alarms Low Subnet Mask Enable TImeout IBUC
Pwr Monitor View Log Output Level IP Gateway Set Trap Verbose Redundancy
Unit Type Freq High Host IP Messages Mode
Pwr Read Clear Log Output Level Telnet Port Echo

Mode Low Switching Mode
Revisions
Burst Thold Suppress Web Refresh Auto Cloning

External LED
Faults Rate
Frequency
Ranges
Burst Count Simulate FSK/RS485 Other IBUC IP
System Time
Faults Address
Total System
Hours
AGC/ALC/ Configure RS485 Baud Firmware
Open Alarms Rate Reboot
Total Tx
Enabled Hours High Temp FSK/RS485
Gain Ctrl Power Supply
Reset Shutdown Delay Hz
Pwr Up State FSK/RS485

Protocol
Pwr Up Delay
10 MHz Adjust
Figure D.3 IBUC G Hand-held Terminal Menu Tree
Menu Options | D-3

Info & Sensors
Tx Power Levels – Displays the input and output power levels.
Sensors – Displays unit power supply voltage, current, DRO voltage, temperature,
and 10 MHz reference state.
Unit Type – Displays frequency band name, rated wattage, and DC voltage required.
Revisions – Displays firmware and hardware revision strings.
Frequency Ranges – Displays LO frequency, RF frequency range, and IF frequency

range.
Total System Hours – Displays the total number of hours that the system has been
operating (that is, the system has been powered On).
Total Tx Enabled Hours – Displays the total number of hours that the transmitter has
been enabled (that is, transmit = On and mute = Off).
Tx
Attenuation – Displays or sets gain attenuator.
Tx On/Off – Displays or sets whether the transmitter is enabled/disabled.
Pwr Monitor Freq – Displays or sets the frequency for power readings from the
IBUC G.
Pwr Read Mode – Displays or sets whether the power reading is collected
continuously or only during bursts.
Burst Thold – Displays or sets the level that determines a valid burst when Pwr Read
Mode is set to burst.
Burst Count – Displays or sets the number of bursts to average for the power reading
when Pwr Read Mode is set to burst.
AGC/ALC/Open – Displays or sets the gain mode of the unit.
Gain Ctrl Reset – Displays the current gain control setting, or sets the gain control to
0.
Pwr Up State – Displays or sets the transmitter state at power up.

Pwr Up Delay – Displays or sets the off time of the transmitter before enabling at
power up.
10 MHz Adjust – Displays or sets the internal 10 MHz frequency trimming value.
Alarm
View Tx Alarms – Displays current transmitter alarms.
View Misc Alarms – Displays current miscellaneous alarms.
View Log – Displays the unit alarm log.
Clear Log – Clears the unit alarm log.
Suppress Faults – Displays or sets whether alarms configured for suppression are
suppressed.
Simulate Fault – Displays or sets a major transmitter alarm (used for

troubleshooting).
Configure Alarms – Displays or sets whether individual alarms cause a major/minor/

no alarm and if the alarm is suppressible.
Hi Temp Shutdown – Displays or sets the high temperature shutdown setting of the
unit.
Tx Thresholds
Input Level High – Displays or sets the input power high threshold.
Input Level Low – Displays or sets the input power low threshold.
Output Level High – Displays or sets the output power high threshold.
Output Level Low - Displays or sets the output power low threshold.
Interface
IP Address – Displays or sets the IP address of the unit.
IP Subnet Mask – Displays or sets the subnet mask of the unit.
IP Gateway –Displays or sets the IP gateway of the unit.
Telnet Port – Displays or sets the TCP port used for Telnet communications.
Menu Options | D-5

Web Refresh Rate – Displays or sets the rate at which web pages will request
updates.
FSK/485 Address – Displays or sets the address used for both the FSK and RS485
links.
RS485 Baud Rate – Displays or sets the baud rate for RS485 communications.
FSK/485 Delay – Displays or sets the amount of time the unit delays sending a
response to a command.
FSK/485 Protocol – Displays or sets the whether the unit communicates with ASCII
protocol or Binary protocol on both the FSK and RS485 links.
SNMP
SNMP Enable – Displays or sets whether SNMPV1 is enabled or not.
SNMP Trap Enable – Displays or sets whether the unit will generate traps. Only
valid when SNMP Enable is enabled.
Set Trap Host IP – Displays or sets the IP address that traps will be directed to.
System
Set Password – Changes the password for the unit. Affects all modes of access.
Password Timeout – Displays or sets the inactivity time before the unit automatically
logs the user off.
Verbose Messages – Displays or sets the format of the replies to commands on all
links.
Echo – Displays or sets whether the unit responds to set commands.
External LED – Displays or sets whether the external LED is used.
System Time – Displays or sets the current system real time clock.
F/W Reboot – Causes the firmware to reboot.
Power Supply Hz – When enabled, applies a 50 Hz correction to AC-powered

IBUC Gs.

Redundancy
This menu item will appear only if the IBUC G is part of a Tx 1+1 system and you are
connecting through the interface box.
Set IBUC Location – Displays or sets the position this IBUC G transmitter occupies
on the waveguide switch.
Set Online IBUC – Displays or change the physical position of the waveguide switch.
Redundancy Mode – Displays or sets whether the unit is free to switch once or
multiple times on a failure.
Switching Mode – Displays or sets whether the unit switches manually or due to unit
alarms.
Auto Cloning – Displays or sets whether the slave unit is updated when parameters
are changed on the master unit.
Other IBUC IP – Displays or sets the partner unit IP address.
Menu Options | D-7


A PPENDIX
LEGACY BINARY CHAPTER0

E
COMMAND MESSAGE STRUCTURE
Command Set
The command set listed in Table E.1 is used on the RS485 and FSK links only when
C4M=1.
Table E.1 IBUC G Commands
Byte Name Description Value

1 Address IBUC G address 0x01 to 0x0F
Request status 0x01
Set Transmit On/Off state 0x02
Change IBUC G address or 
0x03
set RS485 response delay
Set detected carrier frequency 0x04
2 Command
Set power threshold 0x05
Request burst power level 0x06
Request device type ID 0x07
Request / set temperature log 0x09
Gain Attenuator Adjust 0xFF
Table E.1 IBUC G Commands (Continued)

Data Byte 1
If command=
0x01 Not used 0xAA
0 =Off
1 =On
0x02 Tx control
2 =Off @ Pwr On
3 3 =On @ Pwr On
0x03 Set new IBUC G address 0x01 to 0x0F
Set detected carrier frequency
0x04 MSB
MSB
0x05 Set Power threshold MSB MSB
0x06 Request “current burst power”
0x00
selector
Request “stored min/max burst
power” selector 0x01
0x07 Request “IBUC G S/N” selector 0x00
Data Byte 2
If command=
0x01 Not used 0xAA
0x02 Not used 0xAA
4
0x03 RS485 delay value in ms 0x01...0xFF
0x04 Detected carrier frequency LSB LSB
0x05 Power threshold LSB LSB
0xFF Gain Backoff 0x01 to 0xF
Data Byte 3
5 0xAA
Factory Use Only
6 Not used 0xAA
7 Checksum Algebraic Sum of bytes 1-6 Sum of bytes 1-6
Note: Command 0x05
For continuous signal mode (CSM), the setting must be 20.1 dB below rated power.
For burst mode, the setting must be between rated power and no less than 20 dB below
rated power.
Command 0x03, Data Byte 2
The smallest delay is 0x01, which is 1 ms. The delay value of 0x00 is equal to 0xFF
and gives a 256 ms delay. The delay value of 0xAA is the only exception; it will not
E-2 | IBUC G Legacy Binary Command Message Structure

change anything. It aims to maintain compatibility with previous versions of the
software. However, the delay time might not be accurate when the EEPROM write
command is being executed (delay time longer by a few ms).
Legacy Response Message Structure

See Data Field Definitions on page E-5 for valid settings.
Table E.2 Response to IBUC G Commands 0x01, 0x02, 0x03, 0x04, 0x08, and 0xFF

Reports IBUC G Address shifted left by 4
1 Address 0x10 to 0xF0
bits
2 Level Byte 1 Reports current Tx output power MSB MSB
3 Level Byte 2 Reports current Tx output power LSB LSB
4 Temperature Reports Housing Temperature in °C
Status Byte 1
Bit 0: 1=Out of
Housing Temperature
0=Normal
Bit 1: 1=Out of Lock
PLDRO lock
5 0=Normal
Bit 2: 1= Command Error
Checksum
0= Normal
Bit 3: Tx status 1=On, 0=Off
Bits 4 to 7: Power class 0x1 to 0xA
Status Byte 2
Bits 0 to 3: Summary Alarm = On 0x9
6
Summary Alarm = Off 0xA
Bits 4 to 7: Software version 0x0 to 0xF
7 Checksum Algebraic Sum of bytes 1-6 Sum of bytes

(When Data Byte 1 of Command Message = 0x00)

1 Address Address of IBUC G Shifted Left by 4 bits 0x10 to 0xF0
2 Level Byte 1 Current Tx Output Power (Burst Mode) MSB
3 Level Byte 2 Current Tx Output Power (Burst Mode) LSB
4 Level Byte 3 Current Power Threshold MSB
Legacy Response Message Structure | E-3

(When Data Byte 1 of Command Message = 0x00) (Continued)

5 Level Byte 4 Current Power Threshold LSB
Bits 0 to 3: If Command = 0x05 0xB
6 If Command = 0x06 0xC

Bits 4 to 7: 0x00
Table E.4 Response to IBUC G Command 0x06 

(When Data Byte 1 of Command Message = 0x01)

2 Level Byte 1 Max Stored Tx Output Power (Burst Mode) MSB
3 Level Byte 2 Max Stored Tx Output Power (Burst Mode) LSB
4 Level Byte 3 Min Stored Tx Output Power (Burst Mode) MSB
5 Level Byte 4 Min Stored Tx Output Power (Burst Mode) LSB
Bits 0 to 3: 0xD
6
Bits 4 to 7: 0x00
Table E.5 Response to IBUC G Command 0x07

Bits 0 to 3: Manufacturer ID 2
2
Bits 4 to 7: Frequency Band ID 1 to 15
3 Serial Number Byte 1 Decimal Digits 1 and 2 of Serial Number 0000 to 1001
Bits 0 to 3: 0xD
6
Bits 4 to 7: 0x0
Table E.6 Response to IBUC G Command 0x09


Table E.6 Response to IBUC G Command 0x09 (Continued)

0x00 = Off
2 Data Byte 1 Temperature Shutdown @ Temp State
0x01 = On
Minimum Stored Unit Temperature
3 Data Byte 2 0x00...0xFF
(Two’s Complement if below 0)
Maximum Stored Unit Temperature
4 Data Byte 3 0x00...0xFF
(Two’s Complement if below 0)
Number of Writes to Temperature Memory
5 Data Byte 4 After Memory was Cleared or Unit 0x00...0xFF
Rebooted
6 Not Used
Data Field Definitions

Table E.7 contains data field definitions.
Table E.7 Data Field Definitions
Byte Name Description
1 IBUC G Address: Integer between 1 and 15
2 Tx Power Level: Integer in 1/100 dBm
3 Detect threshold Integer in 1/100 dBm
4 Carrier Frequency: Integer in MHz
5 Temperature: Character in ºC

Table E.7 Data Field Definitions (Continued)

Power Class:
2 Watt 1
4 Watt 2
5 Watt 3
8 Watt 4
10 Watt 5
16 Watt 6
20 Watt 7
6
25 Watt 8
40 Watt 9
60 Watt 10 (A)
30 Watt 11 (B)
80 Watt 12 (C)
100 Watt 13 (D)
12 Watt 14 (E)
50 Watt 15 (F)
Frequency Band
Standard C-band 3
Insat C-band 4
Extended Ku-band 5
Standard Ku-band 6
X-band 7
7 Full Ku-band 8
Extended C-band 9
Full C-band 10
Low Ku-band 11
Palapa C-band 12
DBS-band 1 14
DBS-band 2 15

Table E.7 Data Field Definitions (Continued)

The data word consists of 3 bytes of which 4 bits are reserved for
each respective decimal digit. If the serial number consists of fewer
than 6 decimal digits, the remaining digits are filled by zeros (0). For
example: serial number 129 would appear as follows:
Byte 1 Byte 2 Byte 3

1001 0100 1000 0000 0000 0000
9 2 1 0 0 0


A PPENDIX
ASCII COMMAND/RESPONSE STRUCTURE

CHAPTER 0
F
Command Set
This command set is used with Telnet and RS232. The command set is used with
RS485 and FSK only when C4M=0.
Note: All commands and responses are terminated by using <LF><CR>, where
<LF> indicates line feed (0x0A)

<CR> indicates carriage return (0x0D)
Command responses shown are for Terse mode (when C4V=0).
Table F.1 shows the alarm mask that is used with the following commands:
• AHI
• CAS
• CM1
• CM2
• CMS
Table F.1 Alarm Mask
Transmit Alarm Mask

0x0001 AGC/ALC Out of Range Alarm
0x0002 AGC/ALC Not settled Alarm
0x0004 DRO Loss of Lock Alarm
0x0008 Tx Output Threshold High Alarm *
0x0010 Tx Output Threshold Low Alarm *
0x0020 Tx Input Threshold High Alarm *
Table F.1 Alarm Mask (Continued)
Transmit Alarm Mask

0x0040 Tx Input Threshold Low Alarm *
0x0080 High Temperature Alarm *
0x0100 Tx Simulated Alarm
0x0200 10 MHz Reference Alarm
0x0400 Supply Voltage Out of Range Alarm
0x0800 Waveguide Switch Fault (Tx 1+1 operation only)
0x1000 Not Used
0x2000 Supply Current Out of Range Alarm
0x4000 AGC/ALC Target Out of Range Alarm
0x8000 Not Used
* These represent the valid mask for configuring alarms using the CM1, CM2, and CMS commands.
Table F.2 lists possible transmit and miscellaneous alarm flags. Miscellaneous alarms
do not involve the actual transmission of data. Instead, they are primarily
informational.
Table F.2 Alarm Flags

Transmit Flags
0x0001 AGC/ALC Out of Range Alarm
0x0002 AGC/ALC Not settled Alarm
0x0004 IBUC 2 Loss of Lock Alarm
0x0008 Tx Output Threshold High Alarm
0x0010 Tx Output Threshold Low Alarm
0x0020 Tx Input Threshold High Alarm
0x0040 Tx Input Threshold Low Alarm
0x0080 High Temperature Alarm
0x0100 Tx Simulated Alarm
0x0200 10 MHz Reference Alarm
0x0400 VDC (Supply Voltage) Out of Range Alarm
0x0800 Waveguide Switch Fault (Tx 1+1 operation only)
0x1000 Not Used
0x2000 IDC (Supply Current) Out of Range Alarm
0x4000 AGC/ALC Target Out of Range Alarm
0x8000 Not Used
0x0001 Error-log Pointers Corrupted1
0x0002 Fault in Restoring Configuration Data1
F-2 | IBUC G ASCII Command/Response Structure

Table F.2 Alarm Flags (Continued)
Miscellaneous Flags
0x0004 Ethernet Download Alarm1
0x0008 Serial Download Alarm1
0x0010 Reboot Alarm1
0x0020 Clone Communications Error2
0x0040 Clone Read Fault2
0x0080 Clone Write Fault2
1 These alarms can be classified as transient alarms because, when they are triggered, they will not cause the LED
to turn red nor will that alarm appear in the alarm log of the CAS command as a current alarm. It will, however,
appear in the alarm log of the AHI command.
2 These alarms can be classified as persistent alarms because they appear as current alarms in the alarm log of the
CAS command and they do cause the LED to become flashing red indicating the status of the alarm. The alarm
persists until action is taken to clear the condition causing the alarm.
Table F.3 lists the possible error responses when using RS485, RS232, FSK, and
Telnet.
Table F.3 Error Response Table
Code Error Message Description

1 error = invalid value This is not a valid value for this command.
2 error = bad command This command is not in the command set.
3 error = func not yet done This command has not been implemented.
One of the parameters is formatted
4 error = bad format in command
incorrectly.
5 error = error accessing config storage Unable to access EEPROM.
6 error = ODU fault Cannot switch, target unit has a major fault.
7 error = Please enter valid password Incorrect password has been entered.
8 error = Switch Fault The waveguide switch is faulted.
9 error = ODU Comm Fault Legacy Binary packet checksum is invalid.
UDP has timed out waiting for response
10 error = Timeout waiting for packet
packet.
The slave cannot perform the requested
11 error = Not master
command.
Cannot engage AGC/ALC because Tx
12 error = Turn on Tx first
Output is muted.
Cannot engage AGC/ALC because DRO is
13 error = Tx Alarms present
out of lock.
AGC/ALC time out waiting for a valid burst
14 error = Burst Not Detected
(15 seconds).
The ALC target power is outside the valid
15 error = AGC/ALC Targets OOR power range of the unit. The AGC target gain
is outside the range of the unit.
Command Set | F-3

Table F.3 Error Response Table (Continued)
Code Error Message Description

When engaging AGC/ALC mode, the gain
16 error = Gain Control OOR
control is outside preset limits.
17 error = Redund not enabled This unit is not part of a redundant pair.
The IP subnet selected is invalid for the
18 error = Invalid IP for subnet
configured IP address.
19 SET is not valid with <command> You can only query this parameter.
20 GET is not valid with <command> You can only change this parameter.
Common Commands
Commands in this section can be used with transmit and receive systems.
AHI
Description: Displays the contents of the alarm log. The alarm log holds a maximum
of 40 events and events can contain multiple alarms. This is a read-only command.
Error Responses: 7, 19
Response Values:
Event log is empty

AHI=<alarm string>, <alarm string>,…
AHZ
Description: Clears the alarm log.
Response Values:
AHZ=event log cleared
C10
Description: Displays the state of the 10 MHz detector. This is a read-only command.

Response Values:
C10=<Parameter>
Parameter:
0 – 10 MHz is too low
1 – 10 MHz is within range
C4A
Description: Displays or sets the RS485/FSK address. If the address is changed, both
the RS485 and the FSK communication links are affected. The new address is then
used for the response.
Default Value = 1
Command/Response Values:
C4A=<Parameter>
Parameter:
1–15 if C4M=1
1–254 if C4M=0
C4D
Description: Displays or sets the delay in milliseconds before a response is returned on
the RS485 and FSK link.
Default Value = 20
C4D=<Parameter>
Parameter:
1–255
Command Set | F-5

C4R
Description: Displays or sets the RS485 baud rate. This does not affect the FSK link
because that is fixed at 9600 baud.
Default Value = 9600
C4R=<Parameter>
Parameter:
1200, 2400, 4800, 9600, 19200, 38400, 57600, or 115200
C4V
Description: Displays or sets the message response mode. Terse mode is used for
computers where the response items are separated by commas and the message is
terminated with <LF><CR>. Verbose is better suited for use with terminal emulation
programs such as Telnet or HyperTerminal. Output is formatted for easier viewing by
the user. This is a global command affecting all interfaces operating in ASCII mode.
Default Value = 1
C4V=<Parameter>
Parameter:
0 – Terse
1 – Verbose
CAS
Description: Displays the current active alarms. Use the CAS command to display
hexadecimal values that represent the Transmit and Miscellaneous alarms. For the
meaning of the individual alarms or use CAS=1 to display the alarm strings, see
Table F.1 on page F-1.

Response Values:
CAS=T:0x0010, M:0x0010 Tx Only

CAS=R:0x0010, M:0x0010 Rx Only
CCM
Description: Displays the model number and serial number of the IBUC 2. This is a
read-only command.
Error Responses: 1, 7, 19
Response Values:
CCM=<Model number>, <Serial number>

where
Model number is a variable string of up to 20 characters
Serial number is a variable string of up to 10 characters
CCS
Description: Displays the M&C firmware version level. This is a read-only command.
CCS=<Firmware revision string>

where
Firmware revision is a variable string of characters.
Command Set | F-7

CFD
Description: Displays the number of total system operating hours. This is a read-only
command.
CFD=<Number of operating hours>

where
Number of operating hours is a variable string of characters.
CIA
Description: Displays or sets the IP address of the unit. Valid values range from (but
do not include) 1.0.0.0 through 224.0.0.0. When the netmask is applied, 0 and 255 in
the last byte are excluded.
Error Responses: 1, 4, 7, 18
Default Value =192.168.1.21 Tx

192.168.1.254Rx
CIA=<Dotted Decimal IP Address>
CIC
Description: Sets the SNMP community string.
Error Responses: 1, 2, 4, 5, 7
Default: public, private, trap
CIC= public, private, trap

CID
Description: Displays the current consumption. This is a read-only command.
Response Values:
CID=<Parameter>
Parameter:
0.0–25.0 Amperes
CIG
Description: Displays or sets the IP Gateway address. This address cannot be the same
as the IP address of the unit. This is the address the unit will send to if the requested IP
address does not reside on the local LAN segment.
Default Value = 192.168.1.1
CIG=<DOTTED DECIMAL IP ADDRESS>
CIM
Description: Displays or sets the IP netmask. Valid values range from 8 through 30
representing the number of ones in the netmask. This corresponds to 255.0.0.0–
255.255.255.252.
CIM=<netmask>
Command Set | F-9

CIP
Description: Displays or sets the TCP port used for Telnet communication.
Default Value = 23
CIP=<Port>
Port:
1–65535
CIS
Description: Displays or sets the SNMPv1 enable state. When enabled, the unit will
respond to SNMPv1 requests.
Default Value = 1
CIS=<Parameter>
Parameter:
0 – Disable SNMPv1
1 – Enable SNMPv1

CIT
Description: Displays or sets the generation of SNMPv1 traps.
Default Value = 1
CIT=<Parameter>
Parameter:
0 – Disable Traps
1 – Enable Traps
CM1
Description: Displays or sets the minor alarm mask of the unit. This is a hexadecimal
value.
Default Value = 0x00E0
CM1=<Hex Value>
Hex Value:
See Table F.1 on page F-1 for available hexadecimal values.
Command Set | F-11

CM2
Description: Displays or sets the major alarm mask of the unit. This is a hexadecimal
value.
Error Responses:1, 4, 7
Default Value = 0x0018
CM2=<Hex Value>
Hex Value:
CMS
Description: Displays or sets the alarm suppression mask of the unit. This is a
hexadecimal value.
Default Value = 0x0078
CMS=<Hex Value>
Hex Value:
COI
Description: Displays general information about the unit. This is a read-only
command.

CPE
Description: Logs the user into the unit. You cannot query this item.
Command Values:
CPE=<Value>
Value:
1–65535
CPL
Description: Displays the private label string of the unit.
Response Values:
CPL=<Value>
Value:
Variable string up to 20 characters
CPS
Description: Sets the password for logging into the unit. The password does not take
effect until the next login. You cannot query this item.
Default Value: 1234
Command Values:
CPS=<Value>
Value:
1–65535
Command Set | F-13

CPT
Description: Displays or sets the login timeout. After the configured time period
elapses with no user interaction, the session is dropped (ends).
Default Value = 0
CPT=<Value>
Value:
0 – No timeout
1–65535 minutes
CRT
Description: Displays or sets the frequency trimming value of the internal 10 MHz
reference signal.
CRT=<Value>
Parameter:
0 – 255
CTM
Description: Displays or sets the system time.
Default Value: random default value
Command Values:
CTM=<mm/dd/yyyy hh:mm:ss

CVD
Description: Displays the current power supply voltage. This is a read-only command.
Response Values:
CVD=<Value> Tx
CVD=<Value>,<Value> Rx
Value:
0.0–60.0 Volts DC
CWR
Description: Displays or sets the rate at which the Web page automatically refreshes.
Error Responses: 1,7
Default Value = 0
CWR=<Seconds>
Seconds:
0 – No refresh
1–3600 second
Command Set | F-15

CZZ
Description: Reboots the M&C firmware and resets all parameters to their default
values.
CZZ
CZZ=1
Parameter:
1 – Resets only int_values and reboots
Note: This will cause a momentary mute of the transmitter, and should be used with caution.
DCN
Description: Disconnects the current Telnet session.
Error Responses: None
Command Values: No response
EKO
Description: Displays or sets whether the unit responds to commands. If EKO is
disabled, you will receive no response to commands. However, responses are always
returned to queries. This does not affect characters being echoed to the terminal during
Telnet sessions.
Default Value = 1
EKO=<Parameter>
Parameter:
0 – No command response
1 – Respond to commands

Receive-only Commands
This section contains information about various commands used only for reception
CTD
Description: Displays or sets the 10 MHz reference alarm enable state.
Error Responses: 1, 2, 4, 5, 7
CTD=<Parameter>
Parameter:
0 – Disable
1 – Enable
IAH
Description: Displays or sets the current alarm high threshold for the A: side.
Default Value = 500
IAH=<Parameter>
Parameter:
100 – 600 ma (must be greater than the low threshold)
Command Set | F-17

IAL
Description: Displays or sets the current alarm low threshold for the A: side.
Default Value = 250
IAL=<Parameter>
Parameter:
100 – 600 ma (must be less than the high threshold)
IBH
Description: Displays or sets the current alarm high threshold for the B: side.
Default Value = 500
IBH=<Parameter>
Parameter:
100 – 600 ma (must be greater than the low threshold)
IBL
Description: Displays or sets the current alarm low threshold for the B: side.
Default Value = 1
IBL=<Parameter>
Parameter:
100 – 600 ma (must be less than the high threshold)

RAL
Description: Displays or sets the input low power level threshold for the A: side.
Default Value = -40.0
RAL=<Parameter>
Parameter:
5.0 dBm to –40.0 dBm (in 0.1 dBm steps)
RAS
Description: Displays or sets the receive alarm simulation for the A: side unit. Places
alarm relay into “faulted” state and sets bit in alarm byte.
Default Value = 0
RAS=<Parameter>
Parameter:
0 – Off
1 – On
Command Set | F-19

RAZ
Description: Displays or sets receive alarm suppression for the A: side unit. If
suppression is enabled, any alarms configured for suppression by using the CMS
command will not cause a major alarm.
Default Value = 0
RAZ=<Parameter>
Parameter:
0 – Off
1 – On
RBL
Description: Displays or sets input low power level threshold for the B: side unit .
Default Value = 0
RBL=<Parameter>
Parameter:
5.0 dBm to –40.0 dBm (in 0.1 dBm steps)

RBS
Description: Displays or sets the receive alarm simulation for the B: side unit. Places
alarm relay into "faulted" state and sets bit in alarm Byte.
Default Value = 0
RBS=<Parameter>
Parameter:
0 – Off
1 – On
RBZ
Description: Displays or sets receive alarm suppression for the B: side unit. If
Default Value = 0
RBZ=<Parameter>
Parameter:
0 – Off
1 – On
Command Set | F-21

RDT
Description: Displays the current input power level in dBm. This is a read-only
command.
RDT=<Parameter>,<Parameter>
Parameter:
VAH
Description: Displays or sets the high voltage threshold for the A: side.
Default Value = 24
VAH=<Parameter>
Parameter:
10.0 to 25.0 VDC (Must be greater than the low threshold)
VAL
Description: Displays or sets the low voltage threshold for the A: side.
Default Value = 15
VAL=<Parameter>
Parameter:
10.0 to 25.0 VDC (Must be less than High Threshold)

VBH
Description: Displays or sets the low voltage threshold for the B: side.
Default Value = 1
VBH=<Parameter>
Parameter:
10.0 to 25.0 VDC (Must be greater than the low threshold)
VBL
Description: Displays or sets the low voltage threshold for the B: side.
Default Value = 1
VBL=<Parameter>
Parameter:
10.0 to 25.0 VDC (Must be less than High Threshold)
Command Set | F-23

Transmit-only Commands
This section contains information about various commands used only for
transmission.
ATL
Description: Displays the temperature log for the IBUC 2. This is a read-only
command.
Response Values:
ATL=<minimum temperature>, <minimum temperature>, <entries>
C4M
Description: Displays or sets the RS485 or FSK messaging protocol.
C4M=<Parameter>
Parameter:
0 – ASCII
1 – Legacy Binary
For more information, see Appendix E, Legacy Binary Command Message Structure.

CIB
Description: Displays or sets the IP address of the other IBUC 2 in a redundant (Tx
1+1) pair. The A: side IBUC 2 should have the IP address of the B: side IBUC 2
entered here. The B: side IBUC 2 should have the IP address of the A: side IBUC 2
entered here. This enables the IBUC 2 to identify its partner in a redundant pair for
communication purposes.
Example:
A: Side B: Side
CIA=192.168.1.200 CIA=192.168.1.201
CIB=192.168.1.201 CIB=192.168.1.200
CIB=<DOTTED DECIMAL IP ADDRESS>
CLE
Description: Displays or sets the state of the external LED indicator. If disabled, the
external LED indicator will remain off.
Default Value = 1
CLE=<Parameter>
Parameter:
0 – Disabled
1 – Enabled
Command Set | F-25

COX
Description: Displays the current internal temperature of the unit.
COX=<Parameter>
Parameter:
-50 to +100
CSF
Description: Displays or sets a scaling factor. When enabled, this command applies a
50 Hz correction to AC-powered units. This command is not available to DC-powered
units.
Default Value = 0
CSF=<Parameter>
Parameter:
0 – Disabled
1 – Enabled
CTV
Description: Displays the DRO tuning voltage. This is a read-only command.
Response Values:
CTV=<Value>

HLP
Description: Displays the command list with short help strings.
TAH
Description: Displays or sets the output high power threshold. This item must be
greater than the TAL setting.
Default Value = Based upon IBUC 2 power level. See Table F.4 on page F-31.
TAH=<Parameter>
Parameter:
Between rated power and no less than 20 dBm below rated power
TAL
Description: Displays or sets the output low power threshold. This setting must be less
than the TAH setting.
Default Value = Based upon IBUC 2 power level. See Table F.4 on page F-31.
TAL=<Parameter>
Parameter:
Command Set | F-27

TAS
Description: Displays or sets the Tx simulated alarm setting.
Default Value = 0
TAS=<Parameter>
Parameter:
0 – No alarm
1 – Simulate a Tx alarm
TAZ
Description: Displays or sets the alarm suppression setting of the IBUC 2. If
Default Value = 0
TAZ=<Parameter>
Parameter:
0 – No suppression
1 – Suppress configurable alarms

TBH
Description: Displays or sets the input high power threshold. It must be greater than
TBL.
Default Value = -15
TBH=<Parameter>
Parameter:
-15.0 to -60.0
TBL
Description: Displays or sets the input low power threshold. It must be less than TBH.
Default Value = -60
TBH=<Parameter>
Parameter:
-15.0 to -60.0
Command Set | F-29

TBN
Description: Displays or sets the burst count of the IBUC 2. The burst count
determines the number of samples to average to compute current output and input
power. Once a burst is received, the IBUC 2 will collect output power level data every
125 µs. Once 16 samples are collected, they are sorted from highest to lowest value,
and the highest burst count samples are averaged to determine the current power
reading.
Default Value = 8
TBN=<Parameter>
Parameter:
1–16
Note: This command is applicable only to firmware revision 1.00 and below.

TBT
Description: Displays or sets the burst threshold for the IBUC 2. This value determines
the level at which a burst is considered valid.
Default Value = Based upon IBUC 2 power level. See Table F.4.
TBT=<Parameter>
Parameter:
Table F.4 Default Values for the TAH, TAL, and TBT Commands
TAH TAL TBT

Power Level Default Value Default Value Default Value
002 34.0 13.0 13.0
004 37.0 16.0 16.0
005 38.0 17.0 17.0
008 40.0 19.0 19.0
010 41.0 20.0 20.0
012 41.8 21.0 21.0
016 43.0 22.0 22.0
020 44.0 23.0 23.0
025 45.0 24.0 24.0
030 45.8 25.0 25.0
040 47.0 26.0 26.0
050 48.0 27.0 27.0
060 48.8 28.0 28.0
080 50.0 29.0 29.0
100 51.0 30.0 30.0
125 52.0 31.0 31.0
150 52.8 32.0 32.0
175 53.4 32.4 32.4
200 54.0 33.0 33.0
400 57.0 36.0 36.0
Command Set | F-31

TDT
Description: Displays the current input power reading. This is a read-only command.
TDT=<Value>
Value:
-15.0 to -60.0
TFB
Description: Displays the RF frequency band of this IBUC 2. This is a read-only
command.
TFB=<Value>
Value:
3 – Standard C-band (5850–6425 MHz)
4 – Insat C-band (6725–7025 MHz)
5 – Extended Ku-band (13750–14250 MHz)
6 – Standard Ku-band (14000–14500 MHz)
7 – X-band (7900–8400 MHz)
8 – Full Ku-band (13750–14500 MHz)
9 – Extended C-band (5850–6650 MHz)
10 – Full C-band (5850–6725 MHz)
11 – Ku-band Low (12750–13250 MHz)
12 – Palapa C-band (6425–6725 MHz)
14 – DBS-band 1 (17300–18100 MHz)
15 – DBS-band 2 (18100–18400 MHz)
16 – Ka-band 1 (29500–30000 MHz)
17 – Ka-band 2 (30000–31000 MHz)

18 – Ku-band 4 (12800–13300 MHz)
19 – C-band 6 (5725–6425 MHz)
20 – Ka-band 3 (29000–30000 MHz)
TFI
Description: Displays the spectral inversion for this IBUC 2. This is a read-only
command.
TFI=<Value>
Value:
0 – No spectrum inversion
1 – Spectrum is inverted
Command Set | F-33

TFR
Description: Displays or sets the output power monitor frequency of the IBUC 2.
TFR=<Frequency>
Frequency:
Which IF or RF frequency to monitor is based upon the frequency band
of the IBUC 2. IF will be automatically converted to RF.
The default values in Table F.5 are listed according to the model number of the
IBUC 2.
Table F.5 Default Values for the TFR Command
Model Number Default Value

057064 6075
058064 6137
058066 6250
058067 6287
064067 6575
067070 6875
079084 8150
127132 13000
128133 13050
137142 14000
137145 14125
140145 14250
173181 17700
181184 18250
290300 29500
295300 29750
300310 30500

TGC
Description: Displays or sets the operating mode of the IBUC 2. When using AGC or
ALC, the IBUC 2 power levels must be set prior to closing the loop.
Error Responses: 1, 7, 12, 13, 14, 15, 16
Default Value = 0
TGC=<Parameter>
Parameter:
0 – Open loop
1 – Automatic Level Control (ALC)
2 – Automatic Gain Control (AGC)
TGL
Description: Displays the gain and level targets for AGC or ALC. This is a read-only
command.
TGL=<gain target>, <level target>
TGR
Description: Displays or zeroes the gain control of the IBUC 2.
TGR=<Parameter>
Parameter:
-8.0 to 8.0 dB
TGR=0 – Zero Gain Control
Command Set | F-35

TPM
Description: Displays or sets the power monitoring mode of the IBUC 2. When
configured for burst, TBT must also be set. Default values for the TBT command are
given in Table F.4 on page F-31.
Default Value = 0
TPM=<Parameter>
Parameter:
0 – CSM
1 – Burst
TPO
Description: Displays the current output power of the IBUC 2. If TPM is set to burst,
this will be the last valid burst sample of the output power. Use the TFR command to
configure the desired frequency to be monitored. This is a read-only command.
Response Values:
TPO=<Value>
Value:

TPT
Description: Displays or sets the attenuator of the IBUC 2. Changing this value will
increase or decrease the output level/gain of the IBUC 2.
TPT=<Parameter>
Parameter:
0.0–16.0
TSD
Description: Displays or sets the transmit power output delay of the IBUC 2. When
configured, the Tx output will be muted for the time period configured. Once that time
period expires, the Tx output will be enabled or disabled based upon the TSP and TST
settings. If there are Tx faults, the Tx output will not be enabled.
Error Responses:1, 7
Default Value = 0
TSD=<Parameter>
Parameter:
0 – No power up delay
1–500 seconds
Command Set | F-37

TSP
Description: Displays or sets the state of the Tx output at power up.
Default Value = 1
TSP=<Parameter>
Parameter:
0 – Tx output OFF
1 – Tx output ON
TST
Description: Displays or sets the state of the Tx output. This command can be
overridden by alarms.
Default Value = 1
Command Values:
TST=<Parameter>
Parameter:
0 – Disable Tx output
1 – Enable Tx output
Response Values:
Parameter:
0 – Tx Disabled
1 – Tx Enabled, Not Muted
2 – Tx Enabled, Muted

TTS
Description: Displays or sets the high-temperature shutdown alarm. When enabled,
the IBUC 2 will go into alarm mode when the internal temperature reaches 85 °C and
the Tx output will be muted.
Default Value = 1
TTS=<Parameter>
Parameter:
0 – No alarm
1 – Alarm
TTT
Description: Displays the number of hours that the transmitter has been enabled (that
is, with the transmit signal ON and the mute OFF). This is a read-only command.
TTT=<Number of hours>
where
Number of hours is a variable string of characters.
Command Set | F-39

Redundancy Commands
This section contains information about various redundancy commands. The
commands are applicable to Tx 1+1 and Rx 1+1 systems, unless noted otherwise.
Definitions of error responses are found in Table F.3 on page F-3.
BAE
Note: Applies only to Tx 1+1 systems.
Description: Displays the redundancy configuration of the IBUC 2. This is a read-only

command.
Response Values:
BAE=<Redundancy>
Redundancy:
0 – Redundancy not enabled
1 – Redundancy enabled
Position:
Master Position
Slave Position
Clone:
Clone Enabled
Clone Disabled

BAM
Description: Displays or sets the redundancy switching mode of operation. When
configured for reverting, the units can switch between each other when a fault occurs
multiple times unless both units are faulted. In non-reverting operation, when the
A: side unit faults, a switch to the B: side unit will occur unless the B: side unit has
faulted. Once on the B: side unit, no additional switches can occur without user
intervention. This item can be changed only from the Online/Master unit.
Default Value = 0
BAM=<Parameter>
Parameter:
0 – Reverting
1 – Nonreverting
BAP
Description: Displays or sets the position of the IBUC 2 on the waveguide switch. This
does not change the position of the waveguide switch, but instead tells the IBUC 2
firmware to which port the Tx output is connected on the waveguide switch. This item
must be set for each IBUC 2 in a redundant pair.
Default Value = 0
BAP=<Parameter>
Parameter:
0 – A: side
1 – B: side
Command Set | F-41

BCL
Description: Displays or sets the cloning configuration of a redundant pair. The

following commands are always cloned: BAM, BSM, and BCL. They can be changed
only from the Online/Master IBUC 2. All other commands can be individually set
with cloning disabled. When enabled, the following commands are automatically sent
to the Offline/Slave IBUC 2 on a periodic basis: C4V, C4D, C4M, C4R, CPS, CPT,
CM1, CM2, CMS, CWR, EKO, TAH, TAL, TAZ, TBH, TBL, TBN, TBT, TFR,
TPM, TSD, TSP, TST, and TTS and can be changed only from the Online/Master
IBUC 2.
Default Value = 1
BCL=<Parameter>
Parameter:
0 – Disable
1 – Enable

BSM
Description: Displays or sets the switching type. When configured for manual
switching, you can switch between units at will by using the BSW command
regardless of any faults. While in manual mode, the units will not switch due to a fault.
When configured for automatic operation, a switch will occur if a major fault occurs
on the online unit unless the standby is also faulted. If both units are not faulted, you
can switch between the A: side and the B: side by using the BSW command described
on page F-44.
Default Value = 1
BSM=<Parameter>
Parameter:
0 – Manual
1 – Automatic
BST
Description: Displays system status for a redundant pair.
Response Values:
BST=<A: mode>, <A: online>, <B: mode>, <B: online>, <Switch>

A: mode/B: mode: Auto or Manual
A: online/B: online: Online or Standby
Switch: A: side or B: side
Command Set | F-43

BSW
Description: Displays or sets the online status of a redundant pair. This command
controls which unit is online by physically changing the waveguide switch position.
BSW=<Parameter>
Parameter:
0 – A: side
1 – B: side

A PPENDIX
COMPONENT SPECIFICATIONS AND

CHAPTER 0
G
REFERENCE DRAWINGS
This chapter contains component specifications and outline drawings for the Terrasat
Communications, Inc. line of C-band, X-band, and Ku-band intelligent block
upconverters (IBUC Gs), power supply units (PSUIs), low-noise block converters
(LNBs), associated interface units (IFUs, Tx 1+1, and Rx 1+1) and accessories
supplied with IBUC G systems.
Reference Drawings
Outline drawings are subject to change without notice. To ensure that the latest
information is available, contact Terrasat.
Reference Drawings | G-1

Figure G.1 Fabrication Drawing, FBD-21012-XXXX, Rev A
G-2 | IBUC G Component Specifications and Reference Drawings

Figure G.2 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 1 of 2

Figure G.3 Fabrication Drawing, FBD-21984-XXXX, Rev B, page 2 of 2

Figure G.4 Fabrication Drawing, FBD-20606-XXXX, Rev A

5(9,6,216
5(9 '(6&5,37,21 '$7( $33529('
$ 5(/($6(3(5(&2 -+(&+7
' '

& &

&/

)
)
3RZHU 3PD[9$ ,PD[$ ) ))86(6
&ODVV
:
9$&
7$/9
,%8&*
)
)
3RZHU 3PD[9$ ,PD[$ ) ))86(6
&ODVV
:
9$&
7$/9
,%8&*

&$87,21 &$87,21
- $&,1387 %5($7+(59$/9('2127 - $&,1387 %5($7+(59$/9('2127
9$&+] 381&785(255(029( 381&785(255(029(
9$&+]
-
-

#4+;:8'2 #4+;:8'2

#2/4+ #2/4+

-

-
-

% %
&/

:6<67(0$&32:(5

,7(0 47< 7(55$6$73$57 '(6&5,37,21 0$18)3$57

3$57/,67
81/(6627+(5:,6(63(&,),('$//
0$7(5,$/
9*77&8&9(422:3.(&9.438.3(
',0(16,216$5(,1,1&+(6
72/(5$1&(6$5( ;;
;;; &RPPXQLFDWLRQV,QF
127(681/(6627+(5:,6(63(&,),(' 685)$&(),1,6+ $1*/( $
),1,6+
$//35,0$5<',0(16,216$5(6+:21,1'(&,0$/6:,7+0(75,&(48,9$/(7PP 7+,6'2&80(17&217$,16,1)250$7,21
'5$:1%<
(9$5*$6
'$7(
287/,1('5$:,1*

,1%5$&.(76
(1685(7+(5(,6$'(48$7(&/($5$1&()25)$1,17$.($1')$1(;+$867:+(1
35235,(7$5<727(55$6$7&20081,&$7,216 $33529('%<
,1&:+,&+,6(,7+(5&23<5,*+7('25 -+(&+7
'$7(
6<67(0,%8&*&%:*:3/$7(7;
%
3$7(17$33/,(')25$1'253527(&7('%< &+$1*('%< '$7(
02817,1*7+(:6<67(0 5(9
$
75$'(6(&5(7/$:67+,6'2&80(1725$1<
&211(&7256$1'3,1/$<2876$5(6+2:1216+((7 3$5767+(5(2)0$<127%(86('',6&/26('
255(352'8&(',1$1<)250%<$1<
&+(&.('%< '$7(
6,=( '5 2/'
0(7+2'25)25$1<385326(:,7+2877+(
(;35(66:5,77(13(50,66,212)7(55$6$7
&20081,&$7,216,1& '21276&$/('5$:,1* 6&$/( ),/( 2/'5$3 6+((72)
Figure G.5 Outline Drawing, OLD-22191-0000, Rev A, page 1 of 3

5(9,6,216
5(9 '(6&5,37,21 '$7( $33529('
7+58
$ 5(/($6(3(5(&2 -+(&+7
07*+2/(6

' '
;[2%/21*
07&+2/(6

& &

% %

; ;

07*3/$7(
,7(0 47< 7(55$6$73$57 '(6&5,37,21 0$18)3$57

3$57/,67
81/(6627+(5:,6(63(&,),('$//
0$7(5,$/
9*77&8&9(422:3.(&9.438.3(
',0(16,216$5(,1,1&+(6
72/(5$1&(6$5( ;;
$ 685)$&(),1,6+
;;;
$1*/(
&RPPXQLFDWLRQV,QF
$
),1,6+
7+,6'2&80(17&217$,16,1)250$7,21
'5$:1%<
(9$5*$6
'$7(
287/,1('5$:,1*
35235,(7$5<727(55$6$7&20081,&$7,216 $33529('%<
,1&:+,&+,6(,7+(5&23<5,*+7('25 -+(&+7
'$7(
6<67(0,%8&*&%:*:3/$7(7;
%
3$7(17$33/,(')25$1'253527(&7('%< &+$1*('%< '$7(
5(9
$
75$'(6(&5(7/$:67+,6'2&80(1725$1<
3$5767+(5(2)0$<127%(86('',6&/26('
255(352'8&(',1$1<)250%<$1<
&+(&.('%< '$7(
6,=( '5 2/'
0(7+2'25)25$1<385326(:,7+2877+(
(;35(66:5,77(13(50,66,212)7(55$6$7
&20081,&$7,216,1& '21276&$/('5$:,1* 6&$/( ),/( 2/'5$3 6+((72)

127(681/(6627+(5:,6(63(&,),(' 5(9,6,216
%(/2:$5(7+(5R+6&203/,$179(56,212)7+(,17(5)$&($66<---$1'- 5(9 '(6&5,37,21 '$7( $33529('
$1'7+(,50$7(6 $ 5(/($6(3(5(&2 -+(&+7
-$03+(12/37(60$7($03+(12/37(3
--$03+(12/37(30$7($03+(12/37(6
-$03+(12/37(60$7($03+(12/37(3
' %(/2:$5(7+(5R+6&203/,$179(56,212)7+(,%8&*-$1',760$7( ,%8&*&211(&7256&+('8/( '
-$03+(12/37(60$7($03+(12/37(3 5()'(6,* &211(&725 &211(&7250$7(
,17(5)$&($66<-17<3(,138725)7<3(,1387 - 7<3(15(&37 7<3(13/8*

06&,5&8/$5&211 06&,5&8/$5&211
-
%2;07*5&376 675$,*+73/8*3
,17(5)$&($66<---- ,17(5)$&($66<-- ,%8&*-
06(6 06)3
3,1 )81&7,21 3,1 )81&7,21 3,1 )81&7,21
7&3,37; $ 56 $ 56 &211&,5&3( &211&,5&3(
7&3,37; % 56 % 56 - 3$1(/0170$/(5(&37 ,1/,1()(0$/(3/8*
7&3,35; & +$1'+(/'7(50,1$/32:(5 & +$1'+(/'7(50,1$/32:(5 $03+(12/&& $03+(12/&'
1& ' 565;' ' 565;' &RQQ5-5&376+,(/':3&%-$&. &RQQ5-3OXJ.LW6+LHOGHG&DVW

-
1& ( 567;' ( 567;' &21(&7(&+ &21(&7(&+
7&3,35; ) +$1'+(/'7(50,1$/32:(5 ) ++75656&20021
-
1& * $/0B2 * $/$50287 5)021,725 7<3(15(&37 7<3(13/8*
& 1& + $%,' + 12786(' &
- (;7B087( - 12786(' &35&35* &35&35)
5)287
:$9(*8,'( :$9(*8,'(
. 12786(' . 12786('
,17(5)$&($66<- / ,%8&*$/$50287387B12 / ,%8&*$/$50287387B12
0 ,%8&*$/$50287387B&20021 0 ,%8&*$/$50287387B&20021 ,17(5)$&($66<&211(&7256&+('8/(
3,1 )81&7,21
$ 6:,7&+326,7,21$&200$1' 1 ,%8&*$/$50,1387087( 1 ,%8&*$/$50,1387087( 5()'(6,* &211(&725 &211(&7250$7(
% 6:,7&+326,7,21&20021 3 ,%8&*$/$50287387B1& 3 ,%8&*$/$50287387B1&
06&,5&8/$5&211 06&,5&8/$5&211
5 6:,7&+&200$1'$ 5 6:,7&+&200$1'$ -
& 6:,7&+326,7,21%&200$1' %2;07*5&376 675$,*+73/8*3
' 6:,7&+,1',&$725$Q 6 6:,7&+&200$1'% 6 6:,7&+&200$1'% 06(6 06)3
( 6:,7&+,1',&$725&20021 7 6:,7&+,1',&$725$ 7 6:,7&+,1',&$725$
8 6:,7&+,1',&$725% 8 6:,7&+,1',&$725% 06&,5&8/$5&211 06&,5&8/$5&211
) 6:,7&+,1',&$725%Q --
9 5('81'$1&<(1$%/( 9 5('81'$1&<(1$%/( %2;07*5&373 675$,*+73/8*6
06(3 06)6
&RQQ5-5&376+,(/':3&%-$&. &RQQ5-3OXJ.LW6+LHOGHG&DVW
,17(5)$&($66<- ,17(5)$&($66< ,%8&*- ,%8&*- ----
% 3,1 )81&7,21
&21(&7(&+ &21(&7(&+ %
3,1 )81&7,21 5()'(6,* )81&7,21 3,1 )81&7,21
$ 56 7&3,37;
1& --- 7<3(15&37 7<3(13/8*
7;$287387
- 1(875$/
% 56 /%$1'0+])6. 7&3,37; /,1( - 06&,5&8/$5&211 06&,5&8/$5&211
& +$1'+(/'7(50,1$/32:(5 7&3,35; *5281' %2;07*5&376 675$,*+73/8*3
7;,1387
' $B++7BB5;' - 1& 06(6 06)3
/%$1'0+])6.
( $B++7BB7;' 1&
7;%287387
) ++75656&20 - 7&3,35; ,17(5)$&($66<7<3(),QSXW&RQILJXUDWLRQ
/%$1'0+])6.
* 7&3,37; 1&
- 7<3()5&37 7<3()3/8*
+ 7&3,37; 1&
- 7&3,35;
. 7&3,35; ,7(0 47< 7(55$6$73$57 '(6&5,37,21 0$18)3$57
/ $$/$50287387B12 3$57/,67
0 $$/$50287387B&20 81/(6627+(5:,6(63(&,),('$//
0$7(5,$/
9*77&8&9(422:3.(&9.438.3(
',0(16,216$5(,1,1&+(6
$ 1 $$/$50287387B1& 72/(5$1&(6$5( ;;
;;; &RPPXQLFDWLRQV,QF
3 %$/$50287387B12 685)$&(),1,6+ $1*/( $
),1,6+
5 %$/$50287387B&20 '5$:1%< '$7(
(9$5*$6
6 %$/$50287387B1& 7+,6'2&80(17&217$,16,1)250$7,21
35235,(7$5<727(55$6$7&20081,&$7,216 $33529('%< '$7( 6<67(0,%8&*&%:*:3/$7(7;
7 %B++7BB5;' ,1&:+,&+,6(,7+(5&23<5,*+7('25 -+(&+7 ;;
%
3$7(17$33/,(')25$1'253527(&7('%< &+$1*('%< '$7(
8 %B++7BB7;' 5(9
$
75$'(6(&5(7/$:67+,6'2&80(1725$1< &+$1*(%< '$7(
9 (;7B087( 3$5767+(5(2)0$<127%(86('',6&/26('
255(352'8&(',1$1<)250%<$1<
&+(&.('%< '$7(
6,=( '5 2/'
0(7+2'25)25$1<385326(:,7+2877+( &+(&.('%< '$7(
(;35(66 :5,77(1 3(50,66,21 2) 7(55$6$7

Figure G.8 Example Installation Drawing for Antenna Mounting, 339-44001-XXXX, Rev A, page 1 of 2

Figure G.9 Example Installation Drawing for Antenna Mounting, 339-44001-XXXX, Rev A, page 2 of 2

Figure G.10 Example Installation Drawing, IND-10521-0011, Rev A

Data Sheets
Refer to the datasheets in this section for detailed product information.
Product specifications are subject to change without notice. To ensure that the latest
information is available, contact Terrasat.

C-Band IBUC G
GaN
IBUC Advantages
Integrated BUC/SSPA for
higher performance and
reliability.
Integral AC power supply.
Internal 10MHz reference

option automatically switches
to internal reference when
external reference is not
available.
Low phase noise exceeds

IESS308/309 requirements by
a minimum of 10 dB.
NMS‐friendly interfaces en‐

able remote management of
your earth station RF. The revolutionary IBUC has advanced features
Embedded Web pages pro‐ to take your network to new heights.
vide management for small
networks using any Web
browser.
IBUC offers significant benefits:
 Low terminal cost
AGC or ALC circuits hold gain
 Simple design and installation
or output level constant.
 Superior RF performance
30 dB User‐adjustable gain in
 Simplified 1+1 configuration
0.1 dB steps preserves mo‐
dem dynamic range.
New interfaces connect you to the IBUC’s extensive M&C facilities for
Output sample port included. network management or local access. This powerful new M&C enables:
Advanced user interfaces:  Trouble‐free commissioning with easy, point‐and‐click
installation/configuration
 TCP/IP HTTP with embed‐
ded Web pages via RJ45  Continuous verification of performance with time‐stamped
user interface connector alarm history
 SNMP
 Simplified monitoring of terminal status

 TELNET through TCP/IP The IBUC comes with a complete set of diagnostic tools including:
 FSK through TX IFL cable
 10 MHz input detector
 Input voltage and current monitoring
 RS232/485 serial port
 Transmit L‐band input level detector
 Hand‐held terminal  Transmit RF output level detector
 User configurable thresholds and alarms

Unique to the IBUC are internal AGC and ALC functions that satisfy
demanding applications with stringent specifications.
For additional information contact Terrasat Sales at +1 408-782-5911 or by Email: [email protected].
235 Vineyard Court, Morgan Hill, CA 95037 www.terrasatinc.com
C-Band IBUC G
GaN Intelligent Block Upconverter
Frequency range RF IF SSB Phase Noise External reference IBUC

Band 1 Std C-Band 5850 to 6425 MHz 950 to 1525 MHz 10 Hz -115 dBc/Hz -54 dBc/Hz
Band 4 Ext C-Band 5850 to 6650 MHz 950 to 1750 MHz 100 Hz -140 dBc/Hz -79 dBc/Hz
Band 5 Full C-Band 5850 to 6725 MHz 975 to 1850 MHz 1 kHz -150 dBc/Hz -89 dBc/Hz
10 kHz -155 dBc/Hz -94 dBc/Hz
VSWR / Impedance 1.5:1 max / 50 Ohm
Input Connector Type N female (50 Ohm) 100 kHz N/A -100 dBc/Hz
Connector options Type F (75 Ohm), TNC (50 Ohm) 1 MHz N/A -110 dBc/Hz
Input power detector -55 to –20 dBm
External Reference (multiplexed on TX IFL)

Gain
Frequency 10 MHz
Small Signal Gain (L-band to RF)
Level -12 to +5 dBm
with attenuator set to 0 dB 87 dB min
Internal Reference - available
Attenuator range 30 dB variable in 0.1 dB steps

Local Oscillator Frequency
Band 1 7375 MHz 4900 MHz
Gain flatness Band 1 Band 4/5
Band 4 7600 MHz 4900 MHz
Full band 3 dB p-p max 4 dB p-p max
36 MHz 1.5 dB p-p max Band 5 7700 MHz 4900 MHz
1 MHz 0.25 dB p-p Sense Inverting Non-inverting
Gain variation over temperature

IBUC Power Supply
Open loop 3 dB p-p max 4 dB p-p max
Voltage AC 200 to 240 VAC
With AGC 1 dB p-p max
RF Output Power Consumption

Interface CPR-137G at Plin 1600 VA
VSWR 1.3:1 max
at Psat 1900 VA
Output power Band 1 Band 4/5
Psat +56 dBm +55.5 dBm
Monitor and Control
Plin +53 dBm +52.5 dBm Ethernet (HTTP, Telnet, SNMP) via RJ45 connector,
Plin is the maximum linear power as defined by MIL STD 188-164B RS232/485, Hand-held Terminal via MS-type connector,
FSK multiplexed on TX IFL.
Level stability with ALC +0.5 dB

Output power detector range Rated power to –20 dB Environmental
Power reading accuracy + 1.0 dB max. Operating temperature -40oC to +55oC
Spurious @ Plin Relative humidity 100% condensing
In Band -65 dBc Altitude 10,000 ft., (3,000 m) ASL
Out of Band Complies with EN 301 443 and
MIL-STD 188-164 Mechanical
Harmonics @ Plin -50 dBc max. Size 24 x 10 x 7.4 in.
Output Noise Power Density 610 x 254 x 188 mm
TX < -70 dBm/Hz Weight 40 lbs, 18 kg
RX < -150 dBm/Hz
Specifications are subject to change without notice. C-Band 400W IBUC Data Sheet 10/28/13
235 Vineyard Court, Morgan Hill, CA 95037

Tel. +1 408-782-5911 Fax +1 408-782-5912
www.terrasatinc.com
Ku-Band IBUC G
GaN
IBUC Advantages
Integrated BUC/SSPA for
higher performance and
reliability.
Integral AC power supply.
Internal 10MHz reference

option automatically switches
to internal reference when
external reference is not
available.
Low phase noise exceeds

IESS308/309 requirements by
a minimum of 5 dB.
NMS-friendly interfaces en-

able remote management of
your earth station RF.
Embedded Web pages pro- The revolutionary IBUC has advanced features
vide management for small to take your network to new heights.
networks using any Web
browser.
IBUC offers significant benefits:
 Low terminal cost
AGC or ALC circuits hold gain
 Simple design and installation
or output level constant.
 Superior RF performance
30 dB User-adjustable gain in
 Simplified 1+1 configuration
0.1 dB steps preserves mo-
dem dynamic range.
New interfaces connect you to the IBUC’s extensive M&C facilities for
Output sample port included. network management or local access. This powerful new M&C enables:
Advanced user interfaces:  Trouble-free commissioning with easy, point-and-click
installation/configuration
 TCP/IP HTTP with embed-
ded Web pages via RJ45  Continuous verification of performance with time-stamped
user interface connector alarm history
 SNMP
 Simplified monitoring of terminal status
 TELNET through TCP/IP The IBUC comes with a complete set of diagnostic tools including:
 FSK through TX IFL cable
 10 MHz input detector
 Input voltage and current monitoring
 RS232/485 serial port
 Transmit L-band input level detector
 Hand-held terminal  Transmit RF output level detector
 User configurable thresholds and alarms
Unique to the IBUC are internal AGC and ALC functions that satisfy
demanding applications with stringent specifications.
For additional information contact Terrasat Sales at +1 408-782-5911 or by Email: [email protected].
235 Vineyard Court, Morgan Hill, CA 95037 www.terrasatinc.com
Ku-Band IBUC G
GaN Intelligent Block Upconverter
Frequency range RF IF SSB Phase Noise External reference IBUC

Band 1 Std Ku-Band 14.00 to 14.50 GHz 950 to 1450 MHz 10 Hz -115 dBc/Hz -50 dBc/Hz
Band 2 Full Ku-Band 13.75 to 14.50 GHz 950 to 1700 MHz 100 Hz -140 dBc/Hz -75 dBc/Hz
1 kHz -150 dBc/Hz -85dBc/Hz
VSWR / Impedance 1.5:1 max / 50 Ohm
10 kHz -155 dBc/Hz -90 dBc/Hz
Input Connector Type N female (50 Ohm)
Connector options Type F (75 Ohm), TNC (50 Ohm) 100 kHz N/A -95 dBc/Hz
Input power detector -55 to –20 dBm 1 MHz N/A -110 dBc/Hz
Gain External Reference (multiplexed on TX IFL)

Small Signal Gain (L-band to RF) Frequency 10 MHz
with attenuator set to 0 dB 83 dB min Level -12 to +5 dBm
Internal Reference - available
Attenuator range 30 dB variable in 0.1 dB steps
Local Oscillator Frequency

Gain flatness
Band 1 13050 MHz
Full band 4 dB p-p max
Band 2 12800 MHz
36 MHz 1.5 dB p-p max
Sense Non-Inverting
1 MHz 0.25 dB p-p
Gain variation over temperature IBUC Power Supply

Open loop 3 dB p-p max Voltage AC 200 to 240 VAC
With AGC 1 dB p-p max
Power Consumption
RF Output
Interface WR75 UG cover with groove at Plin 1000 VA
VSWR 1.3:1 max at Psat 1200 VA
Output power
Psat +51.8 dBm Monitor and Control
Ethernet (HTTP, Telnet, SNMP) via RJ45 connector,
Plin +49.0 dBm
RS232/485, Hand-held Terminal via MS-type connector,
Plin is the maximum linear power as defined by MIL STD 188-164B
FSK multiplexed on TX IFL.
Level stability with ALC +0.5 dB Environmental

Output power detector range Rated power to –20 dB
Operating temperature -40oC to +55oC
Power reading accuracy + 1.0 dB max.
Spurious @ Plin Relative humidity 100% condensing
Altitude 10,000 ft., (3,000 m) ASL
In Band -65 dBc
Out of Band Complies with EN 301 428 and
MIL-STD 188-164B Mechanical
Size 23 x 10 x 7.4 in.
Harmonics @ Plin -60 dBc max.
584 x 254 x 188 mm
Output Noise Power Density
Weight 40 lbs, 18 kg
TX < -70 dBm/Hz
RX < -150 dBm/Hz
Specifications are subject to change without notice. Ku-Band 150W IBUC Data Sheet 08/28/13
235 Vineyard Court, Morgan Hill, CA 95037

Tel. +1 408-782-5911 Fax +1 408-782-5912
www.terrasatinc.com
A PPENDIX
H
GLOSSARY
CHAPTER 0
Glossary of Terms
The following acronyms are used in Terrasat Communications, Inc. documentation:
°C Degrees Celsius
°K Degrees Kelvin
1RU One Rack Unit (1.75 in.)
s Microsecond
AC Alternating Current
AGC Automatic Gain Control
ALC Automatic Level Control
AWG American Wire Gauge
ATE Automated Test Equipment
ATP Acceptance Test Procedure
BER Bit Error Rate
BUC Block Upconverter
CSM Continuous Signal Mode
CW Continuous Wave
DAB Digital Audio Broadcasting
dB Decibel
dB/oct Decibel per Octave
dBc Decibel Below Carrier
dBm Decibel referenced to 1 milliwatt

DBS Direct Broadcast Satellite
DC Direct Current
DCE Data Communication Equipment
DRO Dielectric Resonator Oscillator
DTE Data Terminal Equipment
DVM Digital voltmeter
EMC Electromagnetic Compatibility
EMI Electromagnetic Interference
ERM Electromagnetic Compatibility and Radio Spectrum Matters
fr Frequency
FSK Frequency Shift Keying
FSS Fixed Satellite Services
F/W Firmware
g Gravity
GHz Gigahertz
GUI Graphical User Interface
HHT Hand-held Terminal
HPA High-Power Amplifier
HPC High-Power Converter
HTTP Hypertext Transfer Protocol
Hz Hertz
I/O Input/Output
IBUC Intelligent Block Upconverter
IDU Indoor Unit
IF Intermediate Frequency
IFL Interfacility Link
IFU Interface Unit
IP Internet Protocol
kg Kilogram
LNB Low Noise Block Converter
LO Local Oscillator
M&C Monitor and Control
max Maximum
H-2 | IBUC G Glossary

MCPC Multiple Carrier Per Channel
MHz Megahertz
MIB Management Information Base
min Minimum
ms Millisecond
MTBF Mean Time Between Failure
MUC Microwave Upconverter
ns Nanosecond
OCXO Oven-controlled Quartz Oscillator
ODU Outdoor Unit
OMT Orthogonal Mode Transducer
p-p Peak to Peak
P1dB Power at the 1dB Compression Point
PFC Power Factor Corrected
PLDRO Phase-Locked Dielectric Resonator Oscillator
PLIN Maximum Linear Power
PLL Phase-Locked Loop
PLLNBC Phase-Locked Low-Noise Block Converter
PLO Phase Locked Oscillator
ppb Parts Per Billion
ppm Parts Per Million
PSAT Point where the output power is at saturation
PSUI Power Supply Unit
Pwr Power
QTP Qualification Test Procedure
QPSK Quadrature Phase Shift Keying
RF Radio Frequency
RFT Radio Frequency Transceiver
RH Relative Humidity
RMS Root Mean Square
RTC Real Time Clock
RTS/CTS Request to Send/Clear to Send
Glossary of Terms | H-3

Rx Receive
s Second
SCPC Single Carrier Per Channel
SNG Satellite News Gathering
SNMP Simple Network Management Protocol
SSB Single Side Band
SSPA Solid-State Power Amplifier
TCP/IP Transfer Control Protocol/Internet Protocol
TRF Transmit Reject Filter
Tx Transmit
UDP User Datagram Protocol
UPC Upconverter
UPS Uninterruptible Power Supply
VAC Volts Alternating Current
VDC Volts Direct Current
VSAT Very Small Aperture Terminal
VSWR Voltage Standing Wave Ratio
VVA Variable Voltage Attenuator
W Watt
WG Waveguide
H-4 | IBUC G Glossary

INDEX
Numerics common mode, 6-2

10 MHz reference signal noise, 6-2
priority, 2-5 transients, 6-2
configuring SNMP, 5-19 to 5-20
connector schedule
A
Tx 1+1, 7-9
adjusting, 3-9 continuous signal mode
alarm log IBUC G power measurement, 5-22
incorrect time stamp, 4-8 converting RS232 to RS485, 5-6
alarms CSM
default configuration, 5-4 See continuous signal mode
ASCII commands
common, F-4 D
receive only, F-17
transmit only, F-24 data packet configuration, 5-8
ASCII Mode data transmission rate
command formats, 5-7 FSK, 5-5
response format, 5-7 RS485, 5-6
attenuation, 2-9 default transmit alarms, 5-4
setting, 3-16 DHCP, 7-31
autocloning differential mode, 6-2
Tx 1+1, 7-7 noise, 6-2
automatic gain control (AGC), 2-9 disconnect devices, 3-5
automatic level control (ALC), 2-9, 4-5
automatic line turnaround, 5-6 E
avoiding enabling the hand-held terminal, D-1
signal saturation, 4-9 Ethernet
SNMP, 5-19
B export regulations, 1-5
block diagram
Tx 1+1, 7-4 F
breather valve, 3-8 factory configuration
burst mode IP address, 5-9
IBUC G power measurement, 5-21 IP gateway, 5-9
subnet mask, 5-9
C Telnet, 5-9
checks frequency plans
M&C, 6-2 transmit, 2-3
power supply, 6-3 FSK
data synchronization, 5-6
data transmission rate, 5-5
Index-1
FSK link specifications IP gateway, 5-9
receiver, 5-5 isolation filter, 3-4
transmitter, 5-5 ITAR
fuses compliance, 1-5
marking schema, 2-5 regulations, 1-5
requirements, 2-4 IUC protection class, 3-5
G L
gain, 2-7, 4-8 L-band input, 2-5
galling, 3-2 Legacy Binary mode, 5-8
grounding lightning
Tx 1+1, 7-15 protection, 7-15
H M
hand-held terminal M&C interfaces
activation, 5-3 Ethernet
adaptive learning, D-2 SNMP, 5-19
disconnecting from, D-2 hand-held terminal
IBUC G menu tree, D-3 activation, 5-3
HyperTerminal multifunction LED, 5-4
establishing a session, B-1 RS232, 5-1
RS485
I ASCII mode, 5-6
IBUC G legacy binary mode, 5-8
available bands, 2-1 mastic tape, 7-13, 7-14
gain, 2-7, 4-8 application, 3-12
L-band input, 2-5 MIBs, 5-21
power measurement
burst mode, 5-21 N
continuous signal mode, 5-21 noise, 6-2
required inputs, 2-5 normal mode, 6-2
system configurations, 2-10 to 2-11 transverse mode, 6-2
IFL normal mode, 6-2
See interfacility link transients, 6-2
interface frequency, 2-1
interfacility link P
definition, 2-1 part number identification, A-1
International Traffic In Arms Regulations Plenum cables
See ITAR use of, 3-9
intetface unit power issues, 6-1
system configurations, 2-10 power measurement
IP address modes, 5-21
default, 5-9
Index-2
power protection devices, 6-2 solid-state power amplifier, 2-7
power supply checks, 6-3 standards
pressure window, 3-8 satellite operation, 1-1
pressurizing, 3-8 storage limitations
priority, 3-9 IBUC G, 2-12
reference signal, 3-9 subnet mask, 5-9
protection system components
lightning, 7-15 Tx 1+1, 7-5
pure carrier, 3-16 system gain adjustment
adjusting system gain
R gain, 3-9
receiver link specifications, 5-5 system requirements, 2-10
reference documents
satellite operation, 1-1 T
reference signal, 3-9 Telnet
priority, 2-5 default port, 5-18
repair policy, 6-7 initiating a session, 5-18
replacement fuse type, 4-7 thresholds
returned material authorization, 6-7 Tx Input, 4-4
RF signal flow Tx Output, 4-4
required inputs, 2-5 time stamp
RMA procedure, 6-7 incorrect data, 4-8
RS232 transceiver faults, 6-1
initiating a session, 5-2 transients
RS485 common mode, 6-2
ASCII mode normal mode, 6-2
response format, 5-7 transmit alarm default configurations, 5-4
automatic line turnaround, 5-6 transmit frequency plans, 2-3
configuring, 5-6 transmit redundant
data transmission rate, 5-6 See Tx 1+1
legacy binary mode, 5-8 transverse mode
noise, 6-2
S traps
saturation SNMP, 5-19, C-20
transmit power, 6-3 Tx 1+1
serial number identification, A-1 autocloning, 7-7
signal saturation block diagram, 7-4
avoidance, 4-9 interface module
Significant Military Equipment, 1-5 block diagram, 7-6
SNMP connectors, 7-5, 7-9
configuration, 5-19 system components, 7-5
MIBs, 5-21
traps, 5-19, C-20
Index-3
U
Ufer ground, 3-6
V
variable attenuator, 2-10, 3-9
voltage
drop, 2-10
W
warranty policy, 1-4
warranty seals
breaking, 1-5
water-resistant wrap
See mastic tape
waveguide, 3-8
flange types, 2-7
Index-4

Manual de Installacion BUC

Uploaded by

Copyright:

Available Formats

Manual de Installacion BUC

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Installacion BUC

Uploaded by

Copyright:

Available Formats

IBUC G

Intelligent Block Upconverter

24-Hour Technical Support: +1 408.782.2166

Part Number: O&M-22063-0001

© November 2013 Terrasat Communications, Inc.

235 Vineyard Court Phone: +1 408.782.5911

Chapter 2, Functional Description

Chapter 5, Monitor and Control Features

Chapter 7, Transmit Redundant Systems

Appendix A, Part Numbering Schema

Appendix B, Using HyperTerminal

Appendix C, IBUC G Web Pages

Appendix D, Hand-held Terminal Menu Tree

Appendix E, Legacy Binary Command Message Structure

Appendix F, ASCII Command/Response Structure

Appendix G, Component Specifications and Reference Drawings

Figure 2.1 Front Panel of an IBUC G ......................................................................................... 2-4

Table P.1 Typographical Conventions ........................................................................................ P-1

Revision Date Description

A1RYember 2013 Initial Release

Conventions and References

Table P.1 describes typographical conventions used in Terrasat Communications, Inc.

Table P.1 Typographical Conventions

Electrical Safety Notice

• Know how to work around, with, and on high-voltage equipment.

• Installation, operation, and maintenance of IBUC G systems

Table 1.1 Satellite Operation Standards

Block Upconverters | 1-1

Reference Documents | 1-3

Export Regulations | 1-5

The written approval of the Directorate of Defense Trade Controls must be

The Terrasat outdoor unit (ODU) consists of an intelligent block upconverter

For a typical equipment configuration, see Figure 2.3 on page 2-11.

The IBUC G is available in a variety of frequency bands as shown in Table 2.1 on

2-2 | IBUC G Functional Description

LO frequency 7.375 GHz 6.950 GHz 13.050 GHz 12.800 GHz

System Components | 2-3

Figure 2.1 Front Panel of an IBUC G

Table 2.2 Fuse Markings

2-4 | IBUC G Functional Description

Table 2.3 explains the fuse marking schema.

Table 2.3 Fuse Markings Explained

Speed Curent Rating Breaking Capacity Voltage Rating

Monitor and Control

System Components | 2-5

Table 2.4 Internal 10 MHz Reference Signal Parameters

2-6 | IBUC G Functional Description

Note: Some units can vary up to 4 dB at any given frequency.

Figure 2.2 depicts the signal flow.

System Components | 2-7

External Detector Multiplier

External 10 MHz Comp

Figure 2.2 IBUC G Block Diagram

2-8 | IBUC G Functional Description

Some of these key features include:

• Monitor and Control

System Components | 2-9

Table 2.5 Basic System Requirements

10 MHz reference signal

2-10 | IBUC G Functional Description