RC Charging Circuit
RC Charging Circuit
RC Charging Circuit
When a voltage source is applied to an RC circuit, the capacitor, C charges up through the
resistance, R
All Electrical or Electronic circuits or systems suffer from some form of “time-delay”
between its input and output, when a signal or voltage, either continuous, ( DC ) or
alternating ( AC ) is firstly applied to it.
This delay is generally known as the time delay or Time Constant of the circuit and
it is the time response of the circuit when a step voltage or signal is firstly applied.
The resultant time constant of any electronic circuit or system will mainly depend
upon the reactive components either capacitive or inductive connected to it and is a
measurement of the response time with units of, Tau – τ
When an increasing DC voltage is applied to a discharged Capacitor, the capacitor
draws a charging current and “charges up”, and when the voltage is reduced, the
capacitor discharges in the opposite direction. Because capacitors are able to store
electrical energy they act like small batteries and can store or release the energy as
required.
The charge on the plates of the capacitor is given as: Q = CV. This charging
(storage) and discharging (release) of a capacitors energy is never instant but takes
a certain amount of time to occur with the time taken for the capacitor to charge or
discharge to within a certain percentage of its maximum supply value being known as
its Time Constant ( τ ).
If a resistor is connected in series with the capacitor forming an RC circuit, the
capacitor will charge up gradually through the resistor until the voltage across the
capacitor reaches that of the supply voltage. The time also called the transient
response, required for the capacitor to fully charge is equivalent to about 5 time
constants or 5T.
This transient response time T, is measured in terms of τ = R x C, in seconds,
where R is the value of the resistor in ohms and C is the value of the capacitor in
Farads. This then forms the basis of an RC charging circuit were 5T can also be
thought of as “5 x RC”.
RC Charging Circuit
The figure below shows a capacitor, ( C ) in series with a resistor, ( R ) forming a RC
Charging Circuit connected across a DC battery supply ( Vs ) via a mechanical
switch. When the switch is closed, the capacitor will gradually charge up through the
resistor until the voltage across it reaches the supply voltage of the battery. The
manner in which the capacitor charges up is also shown below.
RC Charging Circuit
Let us assume above, that the capacitor, C is fully “discharged” and the switch (S) is
fully open. These are the initial conditions of the circuit, then t = 0, i = 0 and q = 0.
When the switch is closed the time begins at t = 0 and current begins to flow into the
capacitor via the resistor.
Since the initial voltage across the capacitor is zero, ( Vc = 0 ) the capacitor appears
to be a short circuit to the external circuit and the maximum current flows through the
circuit restricted only by the resistor R. Then by using Kirchhoff’s voltage law (KVL),
the voltage drops around the circuit are given as:
The current now flowing around the circuit is called the Charging Current and is
found by using Ohms law as: i = Vs/R.
Where:
Vc is the voltage across the capacitor
Vs is the supply voltage
t is the elapsed time since the application of the supply voltage
RC is the time constant of the RC charging circuit
RC Charging Table
Percentage of Maximum
Time
RC Value
Constant
Voltage Current
Note that as the charging curve for a RC charging circuit is exponential, the capacitor
in reality never becomes 100% fully charged due to the energy stored in the
capacitor. So for all practical purposes, after five time constants a capacitor is
considered to be fully charged.
As the voltage across the capacitor Vc changes with time, and is a different value at
each time constant up to 5T, we can calculate this value of capacitor voltage, Vc at
any given point, for example.
RC Discharging Circuit
When a voltage source is removed from a fully charged RC circuit, the capacitor, C will
discharge back through the resistance, R
RC Discharging Circuit
As we saw in the previous RC charging circuit, in a RC Discharging Circuit, the time
constant ( τ ) is still equal to the value of 63%. Then for a RC discharging circuit that
is initially fully charged, the voltage across the capacitor after one time constant, 1T,
has dropped by 63% of its initial value which is 1 – 0.63 = 0.37 or 37% of its initial
value.
The time constant of the circuit is given as the time taken for the capacitor to
discharge down to within 37% of its fully charged value. So one time constant for an
RC disgharge circuit is given as the voltage across the plates representing 37% of its
final value which will be zero volts (fully discharged), and in our curve this is given
as 0.37Vs.
As the capacitor discharges, it loses its charge at a declining rate. At the start of
discharge the initial conditions of the circuit, are t = 0, i = 0 and q = Q. The voltage
across the capacitors plates is equal to the supply voltage and Vc = Vs. As the
voltage across the plates is at its highest value maximum discharge current flows
around the circuit.
Where:
Vc is the voltage across the capacitor
Vs is the supply voltage
t is the elapsed time since the removal of the supply voltage
RC is the time constant of the RC discharging circuit
Just like the previous RC Charging circuit, we can say that in a RC Discharging
Circuit the time required for a capacitor to discharge itself down to one time constant
is given as:
RC Discharging Table
Percentage of Maximum
Time
RC Value
Constant
Voltage Current
Previous
RC Charging Circuit
Next
RC Waveforms
Read more Tutorials inRC Networks
1. RC Charging Circuit
2. RC Discharging Circuit
3. RC Waveforms
4. RC Integrator
5. RC Differentiator
113 Comments
Submit
Pawan
Kay hay ya
Reply
Ansari
Am having one of the question, is anybody having the solution of it.
A capacitor of capacitance C is charged fully with a battery of V volt. After disconnecting the
battry it was connected with another battery of V volt in opposite polarity. What will be the time
taken for capacitor to be fully discharged. Time constant is 5 sec.
Reply
sangwani nyirongo
good and helpful,,, this will improve electronic world
Reply
Clint P.
Need some guidance from the experts on this one.
We have a 12V Maxwell UltraCapacitor Engine Start Module- ULTRA 31/1800
(www.maxwell.com). I need to develop a Capacitor Discharge Tool. This tool will consist of x2
Alligator Clips, Wire and a Resistor. What size resistor do we need to completely discharge a
12V Capacitor? What size wire will be needed as well?
Thank you in advance for the groups help on this.
Kind regards,
Clint P.
robert
they reckon 20k ohms , 5 watts. this for large volt caps. small in circuit caps can be
discharged via short circuit with a screwdriver. most in circuit caps discharge slowly after
a time. to make the tool you talk of , use one alligator clip and a test probe (some old
multimeter thing ) . the alligator clip goes on ground 0v, and use the probe on the positive
of the cap. you can use a multimeter to discharge on the high scale setting. batteries can
be used to charge a capacitor to check to see if they hold charge, ie a 9 volt battery will
charge a cap to 9 volts , though the voltage rating of the cap must be higher than 9 volts,
10 + volt cap. old 9volt batteries reading 7 volts will charge a cap to 7 volts. use voltmeter
to check cap and discharge it. high micro farad caps can spark if discharged by short
circuit,
Reply
D
Regarding the chart – As the capacitor discharges and the voltage drops, why does the
percentage current of maximum increase? And if the current does increase (i’m dubious that it
would) then why doesn’t the capacitor discharge faster and faster? Is it a typo?
Reply
Wayne Storr
No, it is not a typo.
Reply
Dan
In the RC discharge table the current percentage values are incorrect.
They should follow the voltage percentages since after 5 time constants the capacitor should
effectively be completely discharged and therefore there can be no current flowing.
Reply
o More
Mike
Home › Calculators › Supercapacitor-Ultracapacitor discharge … discharge the capacitor.
This can be a constant current or the initial linear … 2019. All …
Reply
Erik
What happens if 5xRC excides the pulse ?
Posted on December 17th 2018 | 11:24 pm
Reply
Mahesh Makwana
I have connected fully charged capacitor 1000uf/25v to 12 v relay coil. I want to know how much
time relay will be ON.
Regards, Mahesh Makwana,
Reply
Ray
why dose it drop below zero?
RC Waveforms
RC circuits can produce useful output waveforms such as square, triangular and sawtooth,
when a periodic waveform are applied to its input
In the previous RC Charging and Discharging tutorials, we saw how a capacitor has
the ability to both charge and discharges itself through a series connected resistor.
The time taken for this capacitor to either fully charge or fully discharge is equal to
five RC time constants or 5T when a constant DC voltage is either applied or
removed.
But what would happen if we changed this constant DC supply to a pulsed or square-
wave waveform that constantly changes from a maximum value to a minimum value
at a rate determined by its time period or frequency. How would this affect the
output RC waveform for a given RC time constant value?
We saw previously that the capacitor charges up to 5T when a voltage is applied and
discharges down to 5T when it is removed. In RC charging and discharging circuits
this 5T time constant value always remains true as it is fixed by the resistor-capacitor
(RC) combination. Then the actual time required to fully charge or discharge the
capacitor can only be changed by changing the value of either the capacitor itself or
the resistor in the circuit and this is shown below.
Typical RC Waveform
If however we now reduced the total time period of the input waveform (higher
frequency, ƒ > 1/10RC), to say “4RC”, the capacitor would not have sufficient time to
either fully charge during the “ON” period or fully discharge during the “OFF” period.
Therefore the resultant voltage drop across the capacitor, Vc would be less than its
maximum input voltage producing an RC waveform as shown below.
Frequency Response
The RC Integrator
The Integrator is a type of Low Pass Filter circuit that converts a square wave input
signal into a triangular waveform output. As seen above, if the 5RC time constant is
long compared to the time period of the input RC waveform the resultant output will
be triangular in shape and the higher the input frequency the lower will be the output
amplitude compared to that of the input.
From which we derive an ideal voltage output for the integrator as:
The RC Differentiator
The Differentiator is a High Pass Filter type of circuit that can convert a square
wave input signal into high frequency spikes at its output. If the 5RC time constant is
short compared to the time period of the input waveform, then the capacitor will
become fully charged more quickly before the next change in the input cycle.
When the capacitor is fully charged the output voltage across the resistor is zero. The
arrival of the falling edge of the input waveform causes the capacitor to reverse
charge giving a negative output spike, then as the square wave input changes during
each cycle the output spike changes from a positive value to a negative value.
from which we have an ideal voltage output for the Differentiator as:
where RC is the time constant of the circuit previously defined and can be replaced
by tau, T. This is another example of how the Time Domain and the Frequency
Domain concepts are related.
Previous
RC Discharging Circuit
Next
RC Integrator
1. RC Charging Circuit
2. RC Discharging Circuit
3. RC Waveforms
4. RC Integrator
5. RC Differentiator
RC Integrator
The RC integrator is a series connected RC network that produces an output signal which
corresponds to the mathematical process of integration.
For a passive RC integrator circuit, the input is connected to a resistance while the
output voltage is taken from across a capacitor being the exact opposite to the RC
Differentiator Circuit. The capacitor charges up when the input is high and discharges
when the input is low.
In Electronics, the basic series connected resistor-capacitor (RC) circuit has many
uses and applications from basic charging/discharging circuits to high-order filter
circuits. This two component passive RC circuit may look simple enough, but
depending on the type and frequency of the applied input signal, the behaviour and
response of this basic RC circuit can be very different.
A passive RC network is nothing more than a resistor in series with a capacitor, that
is a fixed resistance in series with a capacitor that has a frequency dependant
reactance which decreases as the frequency across its plates increases. Thus at low
frequencies the reactance, Xc of the capacitor is high while at high frequencies its
reactance is low due to the standard capacitive reactance formula of Xc = 1/(2πƒC),
and we saw this effect in our tutorial about Passive Low Pass Filters.
If the input signal is a sine wave, an rc integrator will simply act as a simple low
pass filter (LPF) above its cut-off point with the cut-off or corner frequency
corresponding to the RC time constant (tau, τ) of the series network. Thus when fed
with a pure sine wave, an RC integrator acts as a passive low pass filter reducing its
output above the cut-off frequency point.
As we have seen previously, the RC time constant reflects the relationship between
the resistance and the capacitance with respect to time with the amount of time,
given in seconds, being directly proportional to resistance, R and capacitance, C.
Thus the rate of charging or discharging depends on the RC time constant, τ = RC.
Consider the circuit below.
RC Integrator
For an RC integrator circuit, the input signal is applied to the resistance with the
output taken across the capacitor, then VOUT equals VC. As the capacitor is a
frequency dependant element, the amount of charge that is established across the
plates is equal to the time domain integral of the current. That is it takes a certain
amount of time for the capacitor to fully charge as the capacitor can not charge
instantaneously only charge exponentially.
Therefore the capacitor current can be written as:
RC Time Constant
Then we can see that as both i and R cancel out, only T remains indicating that the
time constant of an RC integrator circuit has the dimension of time in seconds, being
given the Greek letter tau, τ. Note that this time constant reflects the time (in
seconds) required for the capacitor to charge up to 63.2% of the maximum voltage or
discharge down to 36.8% of maximum voltage.
Capacitor Voltage
We said previously that for the RC integrator, the output is equal to the voltage
across the capacitor, that is: VOUT equals VC. This voltage is proportional to the
charge, Q being stored on the capacitor given by: Q = VxC.
The result is that the output voltage is the integral of the input voltage with the
amount of integration dependent upon the values of R and C and therefore the time
constant of the network.
We saw above that the capacitors current can be expressed as the rate of change of
charge, Q with respect to time. Therefore, from a basic rule of differential calculus,
the derivative of Q with respect to time is dQ/dt and as i = dQ/dt we get the following
relationship of:
Q = ∫idt (the charge Q on the capacitor at any instant in time)
Since the input is connected to the resistor, the same current, i must pass through
both the resistor and the capacitor (iR = iC) producing a VR voltage drop across the
resistor so the current, (i) flowing through this series RC network is given as:
therefore:
As i = VIN/R, substituting and rearranging to solve for VOUT as a function of time gives:
So in other words, the output from an RC integrator circuit, which is the voltage
across the capacitor is equal to the time Integral of the input voltage, VIN weighted by
a constant of 1/RC. Where RC represents the time constant, τ.
Then assuming the initial charge on the capacitor is zero, that is VOUT = 0, and the
input voltage VIN is constant, the output voltage, VOUT is expressed in the time domain
as:
RC Integrator Formula
We now know that the rate at which the capacitor either charges or discharges is
determined by the RC time constant of the circuit. If an ideal step voltage pulse is
applied, that is with the leading edge and trailing edge considered as being
instantaneous, the voltage across the capacitor will increase for charging and
decrease for discharging, exponentially over time at a rate determined by:
Capacitor Charging
Capacitor Discharging
So if we assume a capacitor voltage of one volt (1V), we can plot the percentage of
charge or discharge of the capacitor for each individual R time constant as shown in
the following table.
τ % Charged % Discharged
1 63.2% 36.7%
2 86.4% 13.5%
3 95.0% 4.9%
4 98.1% 1.8%
5 99.3% 0.67%
Note that at 5 time constants or above, the capacitor is considered to be 100 percent
fully charged or fully discharged.
So now lets assume we have an RC integrator circuit consisting of a 100kΩ resistor
and a 1uF capacitor as shown.
So for a continuous pulse input, the correct relationship between the periodic time of
the input and the RC time constant of the circuit, integration of the input will take
place producing a sort of ramp up, and then a ramp down output. But for the circuit to
function correctly as an integrator, the value of the RC time constant has to be large
compared to the inputs periodic time. That is RC ≫ T, usually 10 times greater.
This means that the magnitude of the output voltage (which was proportional to
1/RC) will be very small between its high and low voltages severely attenuating the
output voltage. This is because the capacitor has much less time to charge and
discharge between pulses but the average output DC voltage will increase towards
one half magnitude of the input and in our pulse example above, this will be 5 volts
(10/2).
Here the first RC integrator converts the original pulse shaped input into a ramp-up
and ramp-down triangular waveform which becomes the input of the second RC
integrator. This second RC integrator circuit rounds off the points of the triangular
waveform converting it into a sine wave as it is effectively performing a double
integration on the original input signal with the RC time constant affecting the degree
of integration.
As the integration of a ramp produces a sine function, (basically a round-off triangular
waveform) its periodic frequency in Hertz will be equal to the period T of the original
pulse. Note also that if we reverse this signal and the input signal is a sine wave, the
circuit does not act as an integrator, but as a simple low pass filter (LPF) with the sine
wave, being a pure waveform does not change shape, only its amplitude is affected.
RC Integrator Summary
We have seen here that the RC integrator is basically a series RC low-pass filter
circuit which when a step voltage pulse is applied to its input produces an output that
is proportional to the integral of its input. This produces a standard equation
of: Vo = ∫Vidt where Vi is the signal fed to the integrator and Vo is the integrated
output signal.
The integration of the input step function produces an output that resembles a
triangular ramp function with an amplitude smaller than that of the original pulse input
with the amount of attenuation being determined by the time constant. Thus the
shape of the output waveform depends on the relationship between the time constant
of the circuit and the frequency (period) of the input pulse.
An RC integrators time constant is always compared to the period, T of the input, so
a long RC time constant will produce a triangular wave shape with a low amplitude
compared to the input signal as the capacitor has less time to fully charge or
discharge. A short time constant allows the capacitor more time to charge and
discharge producing a more typical rounded shape.
By connecting two RC integrator circuits together in parallel has the effect of a double
integration on the input pulse. The result of this double integration is that the first
integrator circuit converts the step voltage pulse into a triangular waveform and the
second integrator circuit converts the triangular waveform shape by rounding off the
points of the triangular waveform producing a sine wave output waveform with a
greatly reduced amplitude.
Previous
RC Waveforms
Next
RC Differentiator
1. RC Charging Circuit
2. RC Discharging Circuit
3. RC Waveforms
4. RC Integrator
5. RC Differentiator
16 Comments
Submit
Jithin raj k
Is there diff in responce for both RC 16T For integrator.
Reply
Kholiswa
Is the time constant greater or smaller than thevmark period of the applied square wave in an
RC intergrated circuit
Reply
Alf
“if the input signal is a sine wave, an rc integrator will simply act as a simple low pass filter
(LPF)”
No . On a single frequency it is just an impedance!
Reply
Wayne Storr
You are half correct as it depends on the value of your single frequency with respect to
tau, either passing it becuse Xc is high, or attenuating it because Xc is low.
Reply
Bhoomikasonkamble
I’d like this stupidity
Reply
Pardeep kumar
No
aman
this article helps me a lottt.
Reply
Mark
If we use the Vout = 1/CR*integral(Vin*dt) from 0 to t. where t= 200 msec. Vin= 10 vdc between
0 and 200 msec…R= 100 K ohms..C= 1uf..so RC= 100 msec.
substitute:
Vout= (10)*integral Vin from 0 to 200 msec so.integrating… Vout=10*Vin*t= 20 vdc @ 200
msec?? NOT 8.64vdc as in the example.. What am I doing wrong.
Reply
shaharia
i got the same result as like as the example
Reply
Jorge
In the analysis, you state that i(t)=Vin/R. This is only true at t=0+. After that, i(t) = (Vin-Vo)/R = C
d(Vo)/dt.
Then, the differential equation becomes:
d(Vo)/dt + Vo/(RC) = Vin/(RC).
It is here that I get stuck demonstrating that Vo is proportional to the integral of Vin, because I’m
left with
vo +1/(RC) *Integral(Vo) = 1/(RC)*Integral(Vin)
What do I do with the integral of Vo?
What is the simplifying assumption?
Reply
o More
Mahendra Singh
I need your help for my experiement
Reply
RC Differentiator
The passive RC differentiator is a series connected RC network that produces an output signal
which corresponds to the mathematical process of differentiation.
For a passive RC differentiator circuit, the input is connected to a capacitor while the
output voltage is taken from across a resistance being the exact opposite to the RC
Integrator Circuit.
A passive RC differentiator is nothing more than a capacitance in series with a
resistance, that is a frequency dependant device which has reactance in series with a
fixed resistance (the opposite to an integrator). Just like the integrator circuit, the
output voltage depends on the circuits RC time constant and input frequency.
Thus at low input frequencies the reactance, XC of the capacitor is high blocking any
d.c. voltage or slowly varying input signals. While at high input frequencies the
capacitors reactance is low allowing rapidly varying pulses to pass directly from the
input to the output.
This is because the ratio of the capacitive reactance (XC) to resistance (R) is different
for different frequencies and the lower the frequency the less output. So for a given
time constant, as the frequency of the input pulses increases, the output pulses more
and more resemble the input pulses in shape.
We saw this effect in our tutorial about Passive High Pass Filters and if the input
signal is a sine wave, an rc differentiator will simply act as a simple high pass filter
(HPF) with a cut-off or corner frequency that corresponds to the RC time constant
(tau, τ) of the series network.
Thus when fed with a pure sine wave an RC differentiator circuit acts as a simple
passive high pass filter due to the standard capacitive reactance formula of XC =
1/(2πƒC).
But a simple RC network can also be configured to perform differentiation of the input
signal. We know from previous tutorials that the current through a capacitor is a
complex exponential given by: iC = C(dVc/dt). The rate at which the capacitor
charges (or discharges) is directly proportional to the amount of resistance and
capacitance giving the time constant of the circuit. Thus the time constant of a RC
differentiator circuit is the time interval that equals the product of R and C. Consider
the basic RC series circuit below.
RC Differentiator Circuit
For an RC differentiator circuit, the input signal is applied to one side of the capacitor
with the output taken across the resistor, then VOUT equals VR. As the capacitor is a
frequency dependant element, the amount of charge that is established across the
plates is equal to the time domain integral of the current. That is it takes a certain
amount of time for the capacitor to fully charge as the capacitor can not charge
instantaneously only charge exponentially.
We saw in our tutorial about RC Integrators that when a single step voltage pulse is
applied to the input of an RC integrator, the output becomes a sawtooth waveform if
the RC time constant is long enough. The RC differentiator will also change the input
waveform but in a different way to the integrator.
Resistor Voltage
We said previously that for the RC differentiator, the output is equal to the voltage
across the resistor, that is: VOUT equals VR and being a resistance, the output voltage
can change instantaneously.
However, the voltage across the capacitor can not change instantly but depends on
the value of the capacitance, C as it tries to store an electrical charge, Q across its
plates. Then the current flowing into the capacitor, that is it depends on the rate of
change of the charge across its plates. Thus the capacitor current is not proportional
to the voltage but to its time variation giving: i = dQ/dt.
As the amount of charge across the capacitors plates is equal to Q = C x Vc, that is
capacitance times voltage, we can derive the equation for the capacitors current as:
Capacitor Current
RC Differentiator Formula
Then we can see that the output voltage, VOUT is the derivative of the input voltage,
VIN which is weighted by the constant of RC. Where RC represents the time
constant, τ of the series circuit.
After the initial positive-going edge of the input signal has passed and the peak value
of the input is constant, the capacitor starts to charge up in its normal way via the
resistor in response to the input pulse at a rate determined by the RC time constant,
τ = RC.
As the capacitor charges up, the voltage across the resistor, and thus the output
decreases in an exponentially way until the capacitor becomes fully charged after a
time constant of 5RC (5T), resulting in zero output across the resistor. Thus the
voltage across the fully charged capacitor equals the value of the input pulse as:
VC = VIN and this condition holds true so long as the magnitude of the input pulse
does not change.
If now the input pulse changes and returns to zero, the rate of change of the
negative-going edge of the pulse pass through the capacitor to the output as the
capacitor can not respond to this high dv/dt change. The result is a negative going
spike at the output.
After the initial negative-going edge of the input signal, the capacitor recovers and
starts to discharge normally and the output voltage across the resistor, and therefore
the output, starts to increases exponentially as the capacitor discharges.
Thus whenever the input signal is changing rapidly, a voltage spike is produced at
the output with the polarity of this voltage spike depending on whether the input is
changing in a positive or a negative direction, as a positive spike is produced with the
positive-going edge of the input signal, and a negative spike produced as a result of
the negative-going input signal.
Thus the RC differentiator output is effectively a graph of the rate of change of the
input signal which has no resemblance to the square wave input wave, but consists
of narrow positive and negative spikes as the input pulse changes value.
By varying the time period, T of the square wave input pulses with respect to the
fixed RC time constant of the series combination, the shape of the output pulses will
change as shown.
RC Differentiator Example
So by having an RC value of one tenth the pulse width (and in our example above
this is 0.1 x 10mS = 1mS) or lower we can produce the required spikes at the output,
and the lower the RC time constant for a given pulse width, the sharper the spikes.
Thus the exact shape of the output waveform depends on the value of the RC time
constant.
RC Differentiator Summary
We have seen here in this RC Differentiator tutorial that the input signal is applied to
one side of a capacitor and the the output is taken across the resistor. A differentiator
circuit is used to produce trigger or spiked typed pulses for timing circuit applications.
When a square wave step input is applied to this RC circuit, it produces a completely
different wave shape at the output. The shape of the output waveform depending on
the periodic time, T (an therefore the frequency, ƒ) of the input square wave and on
the circuit’s RC time constant value.
When the periodic time of the input waveform is similar too, or shorter than, (higher
frequency) the circuits RC time constant, the output waveform resembles the input
waveform, that is a square wave profile. When the periodic time of the input
waveform is much longer than, (lower frequency) the circuits RC time constant, the
output waveform resembles narrow positive and negative spikes.
The positive spike at the output is produced by the leading-edge of the input square
wave, while the negative spike at the output is produced by the falling-edge of the
input square wave. Then the output of an RC differentiator circuit depends on the
rate of change of the input voltage as the effect is very similar to the mathematical
function of differentiation.
Previous
RC Integrator
1. RC Charging Circuit
2. RC Discharging Circuit
3. RC Waveforms
4. RC Integrator
5. RC Differentiator
21 Comments
Submit
Debjeet Chakravorty
Great and best tutorial and I hope for great future .
Poorti
Please insert here differentiation and integration using RC circuits.
Reply
Soulimane MAMMAR
Hi, In the first formula you substitute Vc by Vin and it’s not true!!! Vin = Vc + Vr
Reply
Amanda g
Nice one
Reply
Mohamed
I am sorry , but what do you mean when you said a capacitor “appears” as a short circuit to the
fast changing signal??
thanks for the great tutorials by the way
Reply
Manoj
Sir I think
Can you take capacitor current formula I=C dv/dt
The input square wave pulse rising edge time is in nano second. so the rate of change of
voltage is high. If you substitute the rate of change of voltage in capacitor current formula
you will get enormous current value .it is similar to short circuit. But the current value is
restricted by series resistance, that is equal to I=Vs/R.
Reply
Wayne Storr
Exactly that. For a fast acting dv/dt voltage change as in a step input, the capacitor
appears as a short circuit until it charges.
Reply
Nalin
Excellent tutorial. Thank you very much.
Reply
Deepak
Why in the capacitiors current expresstion voltage across capacitor become equal to input
voltage?
Reply
o More
auwalmadaki
Write your comment hereis
Reply
Mat
Many thanks for such an excellent tutorial. A bunch of stuff is really explained perfectly.
However, this particular tutorial contains some typos which can affect the understanding of the
material. Basically, in order to fully represent input, the RC constant of the differentiator should
be much bigger, than the period of the input signal. As well as production of spikes requires that
RC is much less than period of the input signal.
Reply
Ram
Range of frequency in which HPF acts as a good differentiator