USG Australasia

DONN Brand Grid

®

Suspension Systems
General Offices USG DONN brand suspension systems are the original exposed grid
Hotels
system developed in the 1950’s and still a world leader in technology
and innovation.
Retail Malls
Covering almost every conceivable application, the designer and
Banks
contractor alike have the choice of the traditional 24mm DONN DX
Reception/lobbies system, or the more sophisticated appearance of the 15mm DONN
Centricitee.
Board Rooms

Showrooms Either system integrates seamlessly with USG’s acoustical ceiling

panels to provide an extensive range of options, whether it is for
Education
acoustic, aesthetic or budget reasons. Additionally as a total ceiling
Medical system, USG exposed grid and USG acoustic ceiling panels are covered
by a Lifetime Warranty (up to a maximum of 30 years).
Industrial

Food Preparation Areas For fire protection and safety, DONN DXL can provide a number of
different Fire Resistant Rating (FRR/FRL) ceiling design options
Fire rated areas combined with the appropriate USG Firecode acoustical ceiling panel.

Two systems, multiple applications

Standards and Building Codes ISO 9000 Quality Assurance

USG uses the following Standards in its manufacturing, testing and marketing policies for USG Interiors Pacific Ltd is an
compliance with the respective Building Codes of Australia and New Zealand accredited ISO 9001 – 2008
AS/NZS 2785 - Suspended Ceilings, Design and Installation manufacturer
ASTM C635 - Standard Specification for the Manufacture, Performance and Testing of Licence No. 5044
Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings
AS/NZS 1397 - Steel Sheet and Strip
AS/NZS 1530.3 - Methods for fire tests on building materials, components and structures.
AS 1530.4 - Fire Resistance of Elements of Building Construction Quality
AS/NZS 3837 - Method of test for heat and smoke release rates for materials and
products using an oxygen consumption calorimeter (cone test) ISO 9001
AS/NZS 4600 - Cold Formed Steel Structures Code
AS/NZS 1170 - Structural Design Actions
AS 1170.4 - Earthquake Loads (Australia)
NZS 1170.5 - Earthquake Loads (New Zealand)
NZS 4219 - Specification for Seismic Resistance of Engineered Systems in Buildings
AS 2946 - Suspended Ceilings, Recessed Luminaires and Air Diffusers Interface
NZBC – B1/VM1 - NZ Building Code Verification Method B1/VM1 Clause 2
NZBC – B2 Durability - DONN DX and DONN Centricitee will have a minimum serviceable life of
15 years when installed in a dry, non-corrosive, interior installation
 User’s Guide

ADVANTAGES • A wide product range ensures appropriate load carrying capabilities

of DONN Brand Grid for acoustical ceiling panels and other in-ceiling services
• High tensile QUICK-RELEASE clips on cross tee ends provide fast,
easy, positive lock insertion for quick installation
• Unique DONN Brand QRC design permits quick, easy release of
components without the need for tools
• QUICK-RELEASE cross tee clips reduce the need for additional
wires, clips or fasteners even when designing for seismic
requirements
• For safety and installation speed, cross tees may cantilever and will
not drop out
• Lay-on cross tees resist twist and gapping
• Fire Resistant Ratings available on the DONN DX 24mm system
• DONN Centricitee’s slim 15mm visual face creates a less dominant
grid line than 24mm grid, and is an ideal, cost-effective compromise
between a fully concealed system and easy access to plenum services
• Unique patented centering devices are formed into each Centricitee
cross tee, ensuring rebated and square edged acoustical panels
install square

Contents Page

Components 4-7
Accessory Applications 8
System Layouts 9
Installation and Good Design Practice 10-11
Maximum Allowable Loads 12-15
Lighting Installation 16-17
Transition to Plasterboard Ceilings 18-20
Fire Rating & Seismic Design 21
USG Acoustical Ceiling Panels 22
General Information 23

© 2011

 DONN Brand
®
System Components Advantages

Exposed Grid

DONN® DX®
24mm Exposed Grid

Applications

24mmTee System Profile Product Profile Component Code Panel Edge

Height Length 1 Options
Main Tee Standard 38mm 3600mm DX30D-3600 A, B, C, D
Deep Heavy 38mm 3600mm DX38D-3600 A, B, C, D
Fire Rated 38mm 3600mm DXL38D-3600 A, B, C, D
WideSpanTM 38mm 3600mm DX55D-3600* A, B, C, D
* To special order
Cross Tee Standard 38mm 1200mm DX30D-1200 A, B, C, D
Deep Fire Rated 38mm 1200mm DX38D-1200 A, B, C, D
Fire Rated 38mm 600mm DX30D-0600 A, B, C, D Cross Tee

Q
Medium Standard 32mm 1200mm DX30M-1200 A, B, C, D
ta
DONN Brand DX Suspension System
R R

Standard 25mm 1200mm DX30S-1200 A, B, C, D

Shallow Standard 25mm 600mm DX30S-0600 A, B, C, D

A B C D
Square Edge (SQ) Shadowline Shadowline (SL) Shadowline
Tapered (SLT) Bevel (SLB)

USG Acoustical Panel

Edge Detail

1. Imperial and non-standard lengths/modules available

subject to minimum order quantities and lead times.

Fire Rated Option

DONN DX is available as a Fire Rated option providing protection up to 1 hour, subject to assembly design. Refer to USG Fire Rated Exposed Grid brochure.

Main Tee (Fire Rated) Main Tee (Fire Rated) 38mm 3600mm DXL38D-3600 A, B, C, D
Deep
Cross Tee (Fire Rated) 38mm 1200mm DX38D-1200 A, B, C, D
50mm 100mm 100mm
Cross Tee (Fire Rated) 38mm 600mm DX30D-0600 A, B, C, D
3600mm

 © 2011
 DONN Brand
®
System Components Acoustical
Ceiling Systems
Exposed Grid

DONN® CENTRICITEE®
15mm Exposed Grid

15mmTee System Profile Product Profile Component Code Panel Edge

Height Length 1 Options
Main Tee Main Tee (Standard) 38mm 3600mm DXT30D-3600 A, B, C, D
Deep
Main Tee (Heavy) 38mm 3600mm DXT38D-3600 A, B, C, D

Cross Tee Cross Tee (Standard) 38mm 1200mm DXT30D-1200 A, B, C, D

Deep Cross Tee (Standard) 38mm 600mm DXT30D-0600 A, B, C, D
Cross Tee (Heavy) 38mm 1200mm DXT38D-1200 A, B, C, D

A B C D Patented self centering

2
Square Edge (SQ) Fineline Fineline (FL) Interline device in cross tees
Bevel Edge (FLB) Tapered (ILT) automatically centres
ceiling panel grid module
USG Panel Edge Detail

1. Imperial and non-standard lengths/modules available subject to minimum order quantities and lead times.
2. Limited suitability. Refer to individual acoustical panel brochures

© 2011

System Components
Construction Details Wall Angles

Donn Brand Wall Angles are formed from prepainted, hot dipped galvanised steel. Ends are all square cut
Standard MT45-3600/MT55-3600 Standard Seismic
1.8mm

DONN DX 24mm grid or

Donn Centricitee 15mm grid Hanger within 200mm
22mm

10mm
Temporary (selfdrilling screw)
1.8mm fixing to be removed after
19mm bracing installed.

Seismic Wall Channel US45-3600

MT or ML3600 (for DX)
22mm
MXT3600 (for Centricitee)

Trim to be fixed to wall, max 600mm centres. Fixing to Main or Cross Tee
be relevant to wall strata eg plug and screw or suitable
42mm

nail type fixings. Seismic requirements may take US3600

1.8mm

precedence of type and quantity of fixing. Wall Channel to be fixed at max 600mm centres

26mm

Long Leg ML45-3600 Shadowline Shadow Edge

1.8mm
40mm

1.8mm
19mm

Shadowline Long Leg (steel) MSL45-3600

(aluminium) MSL60-3600
1.8mm
27mm

MSL 3600 ML3600

Shadowline trim fixed to the perimeter wall, Perimeter angle to be fixed to black painted timber
max 600mm centres as for standard trim batten to form shadowedge detail.
10mm

1.8mm

10mm 19mm

Centricitee MXT45-3600 Crimping Option Teg Tab block option Field Cutting Option
1.8mm
22mm

1.8mm

14mm

Shadowline MS45-3000

1.8mm Crimped end TegTab block

of Tee

Cut, then form end with 6mm Trimmed perimeter panels hand rebated to match
15mm

or 10mm crimping tool to suit original rebate

depth of rebate on ceiling panel.
10mm

1.8mm

When setting out ceiling plane,

lower wall angle accordingly to
10mm 12mm
allow for these.

 © 2011
System Components
Accessories

Suspension Clips CL315 CL2424 (Atkar) DFS - 200

Joining Components DGSC-180 DGTC-90 DG-DX

Splice Clip Transition Clip Acoustical Transition Clip

DGMT DH3 DH4

Strongback Clip 3-Way Off-Module Connector 4-Way Off-Module Connector

MT/CT Converter WSC18 (for SQ edge panels) WSC38 (for rebated 24mm)
Joins Main Tees at 90˚ Revoe Partition Attachment Clip WSC38-9 (for rebated 15mm)

Retention Clips L15 PMP (by others) ACM7

Hold Down Clip-Fire Rated Grid Plastic Multi Clip - 8mm-19mm Seismic Clip - Grid to Wall Angle

© 2011

Construction
Details Accessory Applications

The following information will help you select and use the appropriate accessories. Many of the
accessories are multifunctional. Transitions from soffits or flat surfaces can be easier with the use of
accessories.
• Transition Clip joints require at least one (1) hanger within 300mm.
• Splice Clip joints require one (1) hanger within 150mm of splice.

DGTC-90˚ The Transition Clip securely joins 90˚ inside corner

Transition Clip two tier grid components, main tee
Application
regardless of face width, at a 90˚
angle. Bend down tabs secure the
clip to the grid. Screws are required
to provide a structural connection.

tee transition clip

wall angle molding

90˚ outside corner using Transition Clip 90˚ inside corner with channel molding at top edge

US3600
channel
molding
main tee or cross tee cross tee
transition clip

main tee or cross tee

main tee

tee
wall angle

NOTE: At least one (1) hanger is required within 300mm

of a Transition Clip or Channel Molding intersection.

DGSC-180 The primary purpose of the Splice DGSC-180 Another common use of the
Splice Clip Clip is to join two field cut Splice Clip Splice Clip is joining two grid tees
Application A Application B
to length in-line main tees. that are intersecting off module,
such as a utility opening. The link
joining the bend down tabs on
Splice Clip (A) cut the clip is cut allowing it to be
folded on the slotted bend line.

Bend down tabs

over top of bulb
Bend down tabs and flx
over top of bulb
and flx

 © 2011
Construction
Details System Layouts

DONN® DX® Components

24mm Exposed Grid 1 DX3600 Main Tee
2 DX1200 Cross Tee
ax
3 MT3600 Wall Angle 0m
60

4 Hold Down Chip

5 Hanger
6 Panel 00
12

5 12
00

3
4
1 3
Cross Tee
QRC 2 6
tab

0
60

DONN® CENTRICITEE® Components

15mm Exposed Grid 1 DXT3600 Main Tee
2 DXT1200 Cross Tee
3 DXT600 Cross Tee
4 MXT3600 Centricitee Wall Angle ax
0m
60
5 Hanger
6 Panel
7 Hold Down Clip
00
12

5
12
00

4
Cross Tee 1 6 4
QRC 7
tab

3
0
60

© 2011

Requirements and
Good Design
Practices
Installation DONN® Brand
Exposed Grid

Suspended ceilings are finished products intended for interior use and should be treated accordingly.

Delivery, Storage and - All materials shall be delivered in their original, unopened packages and stored for as short a time as possible, in
Handling an enclosed shelter providing protection from exposure to the elements and damage by/to other trades. Damaged,
deteriorated or obviously faulty material is not to be installed and shall be removed from the premises.
- Materials should be handled in such a manner as to prevent racking distortion or physical damage.

Installation - Ceiling layout should be planned prior to installation to determine grid configuration, direction etc. and to ensure that all
fixing points are compatible with structural members and/or other services.
- Installation of exposed grid shall not begin until the building is closed in, fully glazed, roof watertight and residual
moisture from wet trades such as plaster, concrete and terrazzo has dissipated.
- Mechanical and electrical ductwork above the suspension system shall be completed before installation of the suspension
system.

Seismic Bracing Requirements Consult the USG Seismic Design Guide.

Main Tee - For standard installations Main Tees are spaced at 1200mm centres.
- Where heavy ceiling panels are used, close Main Tees in to 600mm centres. Refer Loadings pages 12-15
- Main Tee integral splices are to be offset from each other across the ceiling. Where this cannot be avoided, aligned
splices shall be mechanically fastened with a pop-rivet, tek screw or similar.

Cross Tee - Cross Tees interlock with opposing Cross Tees through the Main Tee web slots to form the required module.

QRC tab - A positive “click” is heard when the DONN QRC tab correctly engages.
- The Cross Tee being installed should be inserted on the left side of the already
Butt Cut Lay-on
Cross
installed Cross Tee.
Cross
Tee Tee - Slots are punched along the Main Tee for convenience at 100mm centres for
DONN Main Tee / Cross Tee Engagement metric systems and 6” for imperial systems.
- Main and Cross Tees can be arranged in a variety of module configurations - see Loadings pages 12-15 for standard
common layouts.
Suspension - Main Tee hangers are spaced at 1200mm centres, no more than 600mm from the perimeter Wall Trim or 150mm
from the Main Tee splice or 200mm from the Main Tee / Cross Tee joint. For heavier ceilings closer spacings may be
required and/or hangers provided through the Cross Tee. Wider spacing may be allowable - see Loadings pages 12-15
or contact your USG Ceiling Specialist.
- For Cross Tees not directly attached to walls and where building movement may be anticipated and there is a risk of
them losing support, provide extra hangers or suitable restraint to the Cross Tees. (eg ACM7 Seismic Clip)
- Where ceilings are back-braced for seismic restraint, do not attach grid to walls. Provide one hanger within 200mm of
the end of every Main Tee and Cross Tee, or suitable support to allow for movement. (eg ACM7)

Suspension methods include:

Multi
- 2.5mm diameter straightened galvanised wire located through the
DONN
Wall Angle hold down pre punched convenience holes in the Main Tee bulb or web and
clip secured with three tight 360° turns.
2.5mm Galvanised
- 2.5mm wire or 5mm galvanised rod with the DONN CL315
Steel Wire suspension clip over the bulb.
(5mm Rod Optional)
DONN DONN - 5mm rod with the CL2424 clip through prepunched hole in the web
Main Tee CrossTee or bulb of DONN Centricitee or DONN DX grid.
USG
Acoustical - Flat steel strip or Wall Angle secured to the tee web with fasteners
Panel
the greater of 50kg or ultimate load from AS/NZS 2785.
- DONN Direct Fixing Clips between bulb holes only (no less than 10mm).
- Hangers are not to be bent or kinked as a means of levelling the grid or for any other reason.
- Hangers or bracing are not to be fixed to, or closer than 150mm to plenum building services e.g. ducting, sprinkler
pipes.
- Fixing of the hanger to the structure above with proprietary fasteners shall be installed in accordance with their
manufacturers recommendations, be suitable for the structure material and comply with any required Standards. Such
fasteners shall have a design ultimate strength the greater of 50kg (0.5kN) minimum, or load requirements of AS/NZS
2785 Clause 3.2.2 (c).)
- Hangers using the CL315 clip shall not vary from the vertical by more than 5°.
- Where hangers are splayed up to a maximum of 45° to the vertical, they should always have an equally applied hanger
in the opposite direction.
- Suspension method and position may be dependant on load requirements. See Step 3 tables pages 13 and 15.

10 © 2011
Requirements and
Good Design
Practices
Installation DONN® Brand
Exposed Grid

Suspension cont. Roof Two trapeze wires required to

Hi span steel purlins balance the ceiling.
- one only will not work

No greater than 45°

Trapeze wires pick up USG DONN Exposed Main vertical Ceiling will want
mid-point of span to Grid or suspension greater to go this way.
carry the load USG Drywall Grid than allowable
suspension span

Wall Perimeter A variety of different Wall Angle profiles are available to suit the Donn Brand systems and designer’s requirements. See
Wall Angles page 6 for details.
- Typically fix trim to walls or bulkheads up to 600mm centres maximum.

Panel Hold Down Clips Clips may be required for seismic restraint, fire ratings or wind uplift on ceiling panels.
- Typically install 2 Hold Down Clips (steel or other) per parallel tee (Cross or Main). This will give four points per panel
restraint.
- Where frequent access in to the plenum is anticipated, some clips can have one side removed to allow clipping one
side of the tee but access on the other.
- Ensure clips are of a type suitable for DONN DX or DONN Centricitee and for the thickness of acoustical panel being
clipped.
Plenum Depths Minimum plenum depths for the ease of removal of
- 600 x 600mm panels = 150mm
- 1200 x 600mm panels = 200mm
Where lesser plenum depth is required, particularly under non-continuous structure or services, like joists/purlins or
ducts, side loading of ceiling panels can further reduce the depth in these areas to 70mm (subject to panel thickness).
Cutting DONN Grid and Wall Angle systems are easily cut on site with aviation snips or fine toothed band or hack saws.

Ceiling Acoustics Acoustical absorption and sound transmission can be controlled to desired levels with the appropriate selection from
the extensive range of USG acoustical ceiling panels. See page 22 for an overview selection. Consult your USG Ceiling
Specialist for advice on a total acoustical ceiling system.

Fire Rating Main, Cross Tees and perimeter trims are non-combustible (BS476 Part 4).
DONN DXL grid system and appropriate USG Firecode acoustical ceiling panel provide floor/ceilings, roof/ceilings
assembly Fire Ratings up to 1 hour. Refer to USG Fire Rated Grid brochure for full details.
Please consult USG Interiors for regional compliance and availability.

Lighting/Air Handling Most standard luminaires, louvres, grills and linear diffusers integrate with the standard module configurations. Refer
Lighting Installation pages 16-17 for specific details.

Thermal Properties DONN suspension systems are unaffected by thermal movement between ambient temperature variations of 10˚ to 30˚C.

Health and Safety The material composition represents no health hazard. When handling, take care and ensure that safe work practices are
adhered to at all times. Some products may have surface treatments and sharp edges/ends. All reasonable care should
be taken when handling or installing to avoid any potential injury to self or others. Users should be properly trained and
supervised in the use and handling of these materials. Appropriate personal protective equipment should be used when
necessary eg: gloves/glasses etc. to avoid any potential injuries.

Maintenance - Cleaning - Remove ceiling panels, then perform necessary cleaning of the grid with non-solvent based commercial
cleaner.
- Painting - Repainting of grid system members should be with a high quality solvent based paint for use over metal
surfaces and applied as recommended by the paint manufacturer.
- Paint colour - Powder coating: Ameron Coatings - Product Code PE522 polyester matt
Colour Code 9249AN ANOGRAIN Pacific White
- Wet spray Ameron Coatings - Product Code 640 Amercryl (acrylic lacquer)
Colour Code 100322 Pacific White NZ

Materials Main and Cross Tees are a double web design, roll formed from hot dipped galvanised steel with prepainted galvanised
steel cap. Cross Tees have a DONN QRC high tensile steel tab clinched to each end, zinc chromate finish.

Partitions A partitions mass may impact on the installation requirements of a suspended ceiling due to seismic movement.
Partitions should not be rigidly fixed to the suspended ceiling where possible, but can be fixed with provision for seismic
or other building movement. The Revoe Clip accessory can be used for this. Refer to the USG Seismic Design Guide for
full details.

© 2011
11
DONN DX
24mm Loadings -
Maximum Allowable
To determine which is the most appropriate and cost effective grid combination compliant with AS/NZS 2785:2000
Suspended Ceilings - Design and Installation, use the following calculations.

Step 1
Maximum Load Calculations G= Grid Weight + Panel Weight + Lights/Fixtures/Insulation etc Weight
Ultimate Limit State
G= + + = kg/m2
1.1 Factored Dead Load
A A = x 1.4 Therefore Maximum Load A = kg/m2

1.2 Factored Dead Load From 1.1 above A kg/m2

A plus +
Factored Service Load U* x1.7 = B kg/m2 Therefore Maximum Load A + B = kg/m2
If required under
B * Where U is 3.0 kg/m2 minimum unless specified otherwise
AS/NZS 2785:2000 Clause 3.2.2(b)

Notes: 1. Load calculations 1.1 and 1.2 are based on AS/NZS 2785:2000 Clause 3.3.5(a). Load calculation 1.2 is based on a
minimum Service Load of 3.0 kg/m² as required by the Standard. The contractor is to confirm that this load will not be
exceeded, or alter the calculation accordingly. If Service Load U is NOT a requirement, use calculation 1.1 values only.
2. These tables apply to areas of buildings that have no openings to the outside, such as doors, windows, ducts etc. In all
other cases the appropriate design loading must be determined by the project structural engineer in accordance with
AS/NZS 2785:2000 Clauses 3.3.5(b) or (c).
3. Standard testing and installation for suspension is at 1200mm centres. Wider centres may be allowable - refer to respective
grid combination tables. Hangers must be within 200mm maximum of Main Tee / Cross Tee connection.
4. Heavy lighting or other mechanical services shall be supported on the main tees, included in the dead load 1.1 above,
able to be supported by the selected grid combination, and/or should be independently supported if greater than 10kg
(NZS4219).
5. All point loads shall be fixed under suspension point on Main Tees only and hanger capacity should be checked against
Step 3.
6. Loadings are laboratory tested in accordance with AS/NZS 2785 with a deflection limit of L/360. Maximum allowable
system loads take into account continuous spans and are applicable for ceilings 2.4 metres or longer. For ceilings shorter
than 2.4 metres use a minimum of two hangers
7. Seismic considerations for in-plane loads may take precedence in determining the required grid combination (refer to the
USG Seismic Design Guide)
8. Not all products may be available in all areas.
9. For non-standard modules eg. 750 x 750mm etc. contact USG for availability and lead times prior to specification.

Step 2 From the grid diagrams below and opposite, select a ceiling layout and hanger spacing where the :
Maximum Load (from Step 1, above) is less than or equal to the Maximum Allowable Load from the Tables.
Alternative Grid Layouts
This will guide you as to the minimum grid combinations to use to fully comply.

Grid Combinations Hanger Spacing (mm) System Weights

Main Tee Cross Tee Cross Tee
1200
2
1000 1100 1350 1500 1800 kg/m

Standard 1200mm x 600mm

DX30D-3600 DX30S-1200 11.6 11.6 11.6 11.6 11.6 N/A 0.76

19.7
Maximum allowable load kg/m²

DX30D-3600 DX30M-1200 23.5 23.5 15.5 11.6 N/A 0.79

DX30D-3600 DX30D-1200 31.3 25.9 19.7 15.5 11.6 N/A 0.87

DXL38D-3600 DX38D-1200 19.0 19.0 14.5 N/A N/A N/A 1.00

Fire Rated Grid

DX38D-3600 DX30D-1200 31.8 31.8 30.1 21.3 15.4 N/A 0.92

DX55D-3600* DX30D-1200 31.8 31.8 31.8 28 20.4 11.8 1.05

*(to special order)

Standard 600mm x 600mm

DX30D-3600 DX30M-1200 DX30S-600 23.5 23.5 19.7 15.5 11.6 N/A 1.00
Maximum allowable load kg/m²

DX30D-3600 DX30D-1200 DX30S-600 31.3 25.9 19.7 15.5 11.6 N/A 1.11

DXL38D-3600 DX38D-1200 DX30D-600 19.0 19.0 14.5 N/A N/A N/A 1.29
Fire Rated Grid

DX38D-3600 DX30D-1200 DX30D-600 31.8 31.8 30.1 21.3 15.4 N/A 1.21

DX55D-3600* DX30D-1200 DX30D-600 31.8 31.8 31.8 28 20.4 11.8 1.34

*(to special order)

12 © 2011
DONN DX
24mm Loadings -
Maximum Allowable
Alternative Grid Layouts Grid Combinations Hanger Spacing (mm) System Weights
Main Tee Cross Tee Cross Tee
1200
2
1000 1100 1350 1500 1800 kg/m

Cross Nogged 1200mm x 600mm

Maximum allowable load kg/m²

DX30D-3600 DX30M-1200 11.7 11.7 11.7 11.7 11.6 N/A 0.79

DX30D-3600 DX30D-1200 15.9 15.9 15.9 15.5 11.6 N/A 0.87

DX38D-3600 DX38D-1200 21.9 21.9 21.9 21.3 15.4 N/A 1.00

DX55D-3600* DX38D-1200 21.9 21.9 21.9 21.9 20.4 11.8 1.13

*(to special order)

Cross Nogged 600mm x 600mm

Maximum allowable load kg/m²

DX30D-3600 DX30M-1200 DX30S-600 11.7 11.7 11.7 11.7 11.6 N/A 1.00

DX30D-3600 DX30D-1200 DX30S-600 15.9 15.9 15.9 15.5 11.6 N/A 1.10

DX38D-3600 DX38D-1200 DX30D-600 21.9 21.9 21.9 21.3 15.4 N/A 1.30

DX55D-3600* DX38D-1200 DX30D-600 21.9 21.9 21.9 21.9 20.4 11.8 1.42
*(to special order)

1200mm x 1200mm
Maximum allowable load kg/m²

DX30D-3600 DX30M-1200 11.7 11.7 11.7 11.7 11.6 N/A 0.54

DX30D-3600 DX30D-1200 15.9 15.9 15.9 15.5 11.6 N/A 0.58

DX38D-3600 DX38D-1200 21.9 21.9 21.9 21.3 15.4 N/A 0.67

DX55D-3600* DX38D-1200 21.9 21.9 21.9 21.9 20.4 11.8 0.80

*(to special order)

600mm x 600mm Heavy

Maximum allowable load kg/m²

DX30D-3600 DX30D-600 51.7 51.7 39.5 31.0 23.3 13.5 1.17

DXL38D-3600 DX30D-600 29.1 29.1 29.1 N/A N/A N/A 1.25

Fire Rated Grid

DX38D-3600 DX30D-600 60.2 60.2 60.2 42.9 30.8 17.8 1.25

DX55D-3600* DX30D-600 77.8 77.8 77.8 56.2 40.7 23.6 1.52

*(to special order)
Maximum allowable load kg/m²

600mm x 1200mm Heavy

DX30D-3600 DX30D-600 51.7 51.7 39.5 31.0 23.3 13.5 0.87

DXL38D-3600 DX30D-600 29.1 29.1 29.1 N/A N/A N/A 0.96

Fire Rated Grid

DX38D-3600 DX30D-600 60.2 60.2 60.2 42.9 30.8 17.8 0.96

DX55D-3600* DX30D-600 63.6 63.6 63.6 56.2 40.7 23.6 1.23

*(to special order)

Use a hanger type and location greater than the Maximum Allowable Loads from the tables above.
STEP 3 Use of these tables must take into account any point loads.
Maximum Allowable Loads
Using a bulb hole Using a web hole Using a CL315 Clip Using a DFS200 Strap
(kg/m2) with Main Tees at
1200mm spacing. - ø 2.5 wire - ø 2.5 wire (between bulb holes only
- CL 2424 - CL 2424 no less than 10mm)
(if at 600mm spacing double the Allowable
Load)

Hanger spacing 1200 1350 1500 1200 1350 1500 1200 1350 1500 1200 1350 1500
DX30D-3600 N/A N/A N/A 33.3 29.6 26.6 40.8 36.3 32.6 N/A N/A N/A
DX38D-3600 31.5 28.0 25.2 48.7 43.3 38.9 49.0 43.6 39.2 37.6 33.4 30.1
(ø 2.5 wire
DXL38D-3600 only) N/A N/A N/A 48.7 N/A N/A N/A N/A N/A N/A N/A N/A
DX55D-3600 46.2 41.1 37.0 45.1 40.1 36.1 62.5 55.6 50.0 78.0 69.3 62.4
© 2011
1
DONN DXT
Centricitee Loadings -
15mm
Maximum Allowable
To determine which is the most appropriate and cost effective grid combination compliant with AS/NZS 2785:2000
Suspended Ceilings - Design and Installation, use the following calculations.

Step 1
Maximum Load Calculations G= Grid Weight + Panel Weight + Lights/Fixtures/Insulation etc Weight
Ultimate Limit State
G= + + = kg/m2
1.1 Factored Dead Load
A A = x 1.4 Therefore Maximum Load A = kg/m2

1.2 Factored Dead Load From 1.1 above A kg/m2

A plus +
Factored Service Load U* x1.7 = B kg/m2 Therefore Maximum Load A + B = kg/m2
If required under
B * Where U is 3.0 kg/m2 minimum unless specified otherwise
AS/NZS 2785:2000 Clause 3.2.2(b)

Notes: 1. Load calculations 1.1 and 1.2 are based on AS/NZS 2785:2000 Clause 3.3.5(a). Load calculation 1.2 is based on a
minimum Service Load of 3.0 kg/m² as required by the Standard. The contractor is to confirm that this load will not be
exceeded, or alter the calculation accordingly. If Service Load U is NOT a requirement, use calculation 1.1 values only.

2. These tables apply to areas of buildings that have no openings to the outside, such as doors, windows, ducts etc. In all
other cases the appropriate design loading must be determined by the project structural engineer in accordance with
AS/NZS 2785:2000 Clauses 3.3.5(b) or (c).

3. Standard testing and installation for suspension is at 1200mm centres. Wider centres may be allowable - refer to
respective grid combination tables. Hangers must be within 200mm maximum of Main Tee / Cross Tee connection.

4. Heavy lighting or other mechanical services shall be supported on the main tees, included in the dead load 1.1 above,
able to be supported by the selected grid combination, and/or should be independently supported if greater than 10kg
(NZS4219).

5. All point loads shall be fixed under suspension point on Main Tees only and hanger capacity should be checked against
Step 3.

6. Loadings are laboratory tested in accordance with AS/NZS 2785 with a deflection limit of L/360. Maximum allowable
system loads take into account continuous spans and are applicable for ceilings 2.4 metres or longer. For ceilings shorter
than 2.4 metres use a minimum of two hangers

7. Seismic considerations for in-plane loads may take precedence in determining the required grid combination (refer to the
USG Seismic Design Guide)

8. Not all products may be available in all areas.

9. For non-standard modules eg. 750 x 750mm etc. contact USG for availability and lead times prior to specification.

Step 2 From the grid diagrams below and opposite, select a ceiling layout and hanger spacing where the :
Maximum Load (from Step 1, above) is less than or equal to the Maximum Allowable Load from the Tables.
Alternative Grid Layouts
This will guide you as to the minimum grid combinations to use to fully comply.

Grid Combinations Hanger Spacing (mm) System Weights

Main Tee Cross Tee Cross Tee
1200
2
1000 1100 1350 1500 1800 kg/m
Maximum allowable

Standard 600mm x 600mm

DXT30D-3600 DXT30D-1200 DXT30D-600 17.6 14.5 11.1 N/A N/A N/A 0.93
load kg/m²

DXT38D-3600 DXT38D-1200 DXT30D-600 28.2 23.3 17.8 14.1 11.3 N/A 1.10
Maximum allowable

Standard 1200mm x 600mm

DXT30D-3600 DXT30D-1200 17.6 14.5 11.1 N/A N/A N/A 0.70
load kg/m²

DXT38D-3600 DXT38D-1200 28.2 23.3 17.8 14.1 11.3 N/A 0.85

1 © 2011
DONN DXT
Centricitee Loadings -
15mm
Maximum Allowable
Alternative Grid Layouts Grid Combinations Hanger Spacing (mm) System Weights
Main Tee Cross Tee Cross Tee
1200
2
1000 1100 1350 1500 1800 kg/m

Maximum allowable
Cross Nogged 1200mm x 600mm DXT30D-3600 DXT30D-1200 12.8 12.8 11.1 N/A N/A N/A 0.70

load kg/m²
DXT38D-3600 DXT38D-1200 17.1 17.1 17.1 14.1 11.3 N/A 0.85

Maximum allowable
Cross Nogged 600mm x 600mm
DXT30D-3600 DXT30D-1200 DXT30D-600 12.8 12.8 11.1 N/A N/A N/A 0.93

load kg/m²
DXT38D-3600 DXT38D-1200 DXT30D-600 17.1 17.1 17.1 14.1 11.3 N/A 1.10

Maximum allowable

1200mm x 1200mm
DXT30D-3600 DXT30D-1200 12.8 12.8 11.1 N/A N/A N/A 0.47
load kg/m²

DXT38D-3600 DXT38D-1200 17.1 17.1 17.1 14.1 11.3 N/A 0.57

Maximum allowable

600mm x 600mm
DXT30D-3600 DXT30D-600 35.2 29.1 22.2 17.6 14.2 N/A 0.93
load kg/m²

DXT38D-3600 DXT30D-600 56.5 46.7 35.7 28.3 22.6 13.1 1.00

Maximum allowable

600mm x 1200mm
DXT30D-3600 DXT30D-600 35.2 29.1 22.2 17.6 14.2 N/A 0.70
load kg/m²

DXT38D-3600 DXT30D-600 51.3 46.7 35.7 28.3 22.6 13.1 0.80

Use a hanger type and location greater than the Maximum Allowable Loads from the tables above.
STEP 3 Use of these tables must take into account any point loads.
Maximum Allowable Loads
Using a bulb hole Using a web hole Using a CL315 Clip Using a DFS200 Strap
(kg/m2) with Main Tees at
1200mm spacing. - ø 2.5 wire - ø 2.5 wire (between bulb holes only
- CL 2424 - CL 2424 no less than 10mm)
(if at 600mm spacing double the Allowable
Load)

Hanger spacing 1200 1350 1500 1200 1350 1500 1200 1350 1500 1200 1350 1500
DXT30D-3600 N/A N/A N/A 33.3 29.6 26.6 40.8 36.3 32.6 N/A N/A N/A
DXT38D-3600 31.5 28.0 25.2 48.7 43.3 38.9 49.0 43.3 39.2 37.6 33.4 30.1

© 2011
1
Construction Details
Lighting Installation
As worldwide leaders in acoustical ceiling systems, USG Interiors works with the major lighting manufacturers to ensure system
compatibility is maintained. The following guidelines are designed to assist in the correct specification and installation of light
fittings in USG’s DONN Brand Exposed Grid and acoustical ceiling systems.

Luminaire Positioning Typical recessed pan fitting arrangements are shown below. Main Tees at 1200mm centres are shown horizontal, with
suspension at 1200mm centres.

• Indicates Suspension Points

Refer to Loadings (pages 12-15) for maximum allowable gross ceiling loads depending on type of luminaire and DONN grid
selected.
Where luminaire weight exceeds uniform load maximums consider:
a) A higher specification DONN Brand grid option if applicable (Refer to Loadings pages to ensure compliance).
b) Independent support from structure.
c) Additional suspension points as shown below, or similar.

DONN BRAND Grid Profiles When recessed pan fittings use Profile D Main Tee S Cross Tee M Cross Tee D Cross Tee
the top of the DONN tee bulb for DONN
support, use the same height CENTRICITEE
tee profiles for even support
38 38

15 15

DONN DX

38 38
32
25

24 24 24 24

Attachment of Light Fittings Fluorescent Recessed Pans / Troffer Packs

Fittings occupying a full ceiling module e.g 1200 x 600 / 600 x 600 etc. locate on the bulb of the tee or sit inside the tee and rest
on the flange. With either method a positive fixing to the grid is recommended for safety reasons. This is required by the NZ
Standard NZS 4219 (see over). For Australia ref. AS2946 for interface compatibility.

Fluorescent Surface Fittings / Battens

Surface mounted luminaires require a minimum of two fasteners to attach to the grid. Wherever possible, attach to the main
tee. Where this is not possible and cross tees have to be used, keep fasteners as close as possible to main tee intersection for
greatest strength. Proprietry fasteners are availbale that snap on to DONN DX 24mm grid profiles.
Where a fitting’s weight exceeds maximum allowable loads for a particular grid type, any of the following methods may be used:
- use a proprietary fastener that fully surrounds the grid and is independently supported from the structure above.
- provide additional suspension points to the grid directly above the fixing point, ensuring each suspension is in
compliance with AS/NZS 2785 Clause 3.2.2 (c) (50kg minimum).

1 © 2011
Construction Details
Lighting Installation

Ceiling Panel Mounted Fittings Light fittings mounted through USG acoustical ceiling panels shall not rely on the ceiling panel for support. Their weight shall be
transferred back to the grid by:

Side End
a) Simple supports across Elevation Elevation
the back of the ceiling panel

b) Simple supports onto the

top of the tee bulb

c) An additional rigid panel

across the back of the NB: This method will affect
ceiling panel the acoustic properties of
the ceiling panel

Common Recessed This table is intended as a general guide only. All products may not be available in all areas. Local manufacturers may also
Luminaire Options provide compatible options. For full luminaire details and options, contact the nearest Lighting Company office.

Company Type Module Grid Type

GEC Troffer - DONN DX and

Lay-in Diffuser 1200 x 600* 600 x 600 1200 x 300 DONN Centricitee
Philips
DONN DX and
Thorn Framed Diffuser 1200 x 600 600 x 600 1200 x 300 DONN Centricitee

*These options may be used with DONN Centricitee when used in conjunction with a 3.5mm prismatic diffuser.
TIP: When specifying lighting, ensure the grid type is clearly identified in the lighting section
e.g. DONN Centricitee 15mm exposed grid
DONN DX 24mm exposed grid.

Standards Australia - AS2946 - 1991 Suspended Ceilings, Recessed Luminaires and Air Diffusers - Interface Requirements for Physical
Compatibility. This standard details primarily the dimensional limitations and how they suit different ceiling grid system types.
New Zealand - NZS 4219 - 2009 Specification for Seismic Resistance of Engineering Systems in Buildings. This standard
covers building services in close proximity, attached to, or passing through suspended ceilings. Relevant clauses pertaining to
lighting are paraphrased below:
2.24 Electrical reticulation shall be independently supported, or allowance shall be made for relative building or ceiling
movement.
2.25.2 All luminaires shall be positively clamped or fixed to the ceiling grid system.
2.25.3 All luminaires weighing greater than 10kg shall have two supports from the structure above. Each support shall be
capable of supporting the full luminaire’s weight.
2.25.4 Surface mounted luminaires shall be fixed to the ceiling grid with at least two fixtures that completely surround the tee.
2.29.1 All ceiling suspended services including luminaires not exceeding 10kg in weight, shall be positively secured to the
ceiling grid, or to the structure above, but not supported by the ceiling panels or tiles. Separate equipment supports
are not necessary if the equipment is adequately fastened to the grid, and the grid has been specifically designed to
withstand both the gravity and seismic loading from the equipment.

The contents of this section have been compiled in good faith based on current industry information at time of printing. Whilst
USG Interiors has taken all care to ensure accuracy, it cannot be held liable for information that is: inappropriate for its application;
changed after publication or availability of all products in all areas.
For additional help contact your nearest Lighting Company office or USG Interiors.

© 2011
1
System Components
Construction Details Transition to a
Plasterboard Ceiling

The Donn® DX® and CENTRICITEE® acoustical suspension systems are totally compatible with our new USG Drywall
Grid Suspension System making it easy to transition between flat drywall and acoustical ceilings.

Flush or offset transitions are possible. Additional cross tees are necessary at drywall edge to provide adequate support
(as shown on plan view).

hanger

drywall acoustical
cross tees acoustical lay-in panel
cross tees
C
19 acoustical
main tee
drywall main tee

D
acoustical 19/20
main tee

knurled channel molding

gypsum panel

acoustical main tees 1200 mm acoustical cross tees

additional 600mm drywall

cross tee (off module) ø
field installed
hanger

1200 mm drywall cross tees

acoustical ceiling
drywall ceiling

line of drywall
extra 1200mm
drywall cross
tees (gypsum
panel support) ø

drywall main tees

ø gypsum panel manufacturer's requirements

1 © 2011
 (by others)
drywall
main tee

C
Construction Details
19

Drywall to acoustical transition--field cut connection Drywall to acoustical transition

acoustical main tee

acoustical 50-100mm additional cross tee
for gypsum panel support
cross tee
acoustical
splice clip acoustical acoustical acoustical drywall drywall drywall
main tee
drywall cross tee main tee cross tee cross tee main tee cross tee

drywall bead
(by others)
drywall bead
drywall acoustical (by others) gypsum panel
gypsum panel
main tee panel acoustical ceiling drywall ceiling

C D
19 19

Drywall to acoustical transition--factory end connection Flush transitions Standard offset

hanger
drywall acoustical hangers hanger
main tee main tee
channel
50 mm 50 mm cross tee molding main tee channel molding tee

acoustical
acoustical panel
38 mm gypsum panel drywall bead acoustical gypsum panel
panel
15 mm or panel gypsum panel
24 mm
C alt D alt D alt2
19 19 19

Flush Acoustical DG - DX Flush Acoustical Transition clip Assembled

Transition Clip

acoustical fasten to main tee to prevent

main tee movement if required

acoustical
cross tee

drywall
QRC slot for drywall cross tee square edge
cross tee acoustical panel

DG - DX
10/13mm gypsum panel acoustical
transition clip

Intersection Detail Drywall cross tee Flush

Transition
Clip
Acoustical
cross tee

D alt3 Donn acoustical

10/13mm Gypsum board Square edge
19 main tee acoustical panel

© 2011
1
Construction Details
Transition to a
Plasterboard Ceiling
Main Tee Direction - keep acoustical and drywall main tees in line

Option 1

FASTENTOMAINTEETOPREVENT
MOVEMENTIFREQUIRED
MT / CT converter flush MT / CT
transition converter
clip
ACOUSTICAL
MAINTEE
-4#4
CONVERTER
-4#4
CONVERTER SQUAREEDGE
ACOUSTICALPANEL
additional cross tee for 10/13mm Donn acoustical square edge
gypsum panel support gypsum board main tee at acoustical panel
ADDITIONAL transition junction
$' $8 ACOUSTICALMAINTEE
ACOUSTICAL ATTRANSITION C alt 2
MMGYPSUM TRANSITIONCLIP 20
BOARD

Option 2
!COUSTICAL
CROSSTEE

hangers
DGSC-180
splice clip
drywall channel DGSC-180
main tee molding splice clip
acoustical
main tee

drywall
main square edge
tee acoustical panel

additional cross tee for 10/13mm Donn acoustical square edge

DGPC-40 gypsum panel support gypsum board main tee at acoustical panel
channel additional
transition junction
acoustical main tee
at transition C alt 3
10/13mm gypsum board
20

Option 3

hangers
see detail Application B
page 8
drywall DGSC-180 acoustical
DGSC-180 main tee splice clips main tee
splice clip
acoustical
main tee

drywall
main square edge
tee acoustical panel
additional cross tee for 10/13mm Donn acoustical square edge
gypsum panel support gypsum board main tee at acoustical panel
DGSC-180 transition junction
additional
splice clip acoustical main tee C alt 4
10/13mm gypsum board at transition 20

20 © 2011
DONN Exposed
Grid Systems -Fire Rating
-Seismic Installation
Fire Rating - USG USG acoustical ceiling systems can provide a FRR/FRL (Fire Resistant Rating) up to 60/60/60 as well
Acoustical Ceiling System as the benefits of acoustical control while still allowing easy plenum access to services, particularly
24mm Eposed Grid compared to plasterboard options.

A fire rated ceiling helps prevent fire and/or heat from reaching a floor or roof above a room that is on
fire. This allows time for evacuation of the floors above and protects against property damage. A fire
rated ceiling system is part of a total fire rated assembly, which includes approved beams, joists and
floor or roof assemblies.
• BRANZ Tested to AS1530.4 Fire Resistant Tests of Elements of Building Construction
• Exclusive expansion notch formed into the main tee is designed for controlled collapse in the event
of a fire, ensuring integrity of the ceiling plane
• Heavy weight tees resist buckling, longer
• Visually identical to USG DONN Brand 24mm exposed grid where the same image is required in
non-fire rated areas
• High density USG Firecode ceiling panels provide choices of size, appearance and acoustical
properties to suit a range of applications
• Plus all the fast easy installation features of standard DONN DX exposed grid systems

For fire rating options and full construction details please refere to our main brochure :
USG Fire Rated Exposed Grid System or visit our website at www.usg.coz.z nzz z w.usgco-Zz

Seismic Installatiozznz USG DONN Brand grid systems are world

leaders in engineering technology to resist
earthquake destruction and the compromise
of human safety under suspended ceilings.
Accordingly USG Australasia have invested
significantly in steel engineering, testing and
using expert seismic consulting engineers in
preparing the :
USG Seismic Design Guide
for correct installation of USG ceilings in
compliance with AS/NZS 1170. Please contact
USG for the full Design Guide
© 2011
21
 USG Acoustical
Ceilings Panels
Whether it is for acoustical, aesthetic, budgetary or performance reasons, USG have a range of panels
to suit most application requirements. All panels bearing the ClimaPlus™ branding are formulated
specifically to resist high temperatures and humidity#. Combined with USG DONN Brand grid the total
system is covered by a Lifetime Warranty (up to a maximum of 30 years). Below are some common
examples supplied throughout Australasia. (Note: some options may not be available in all areas)

Panel Textzure Description NRC CAC

White vinyl laminated surface with Class 100 Class 100
Clean Room™
special edge and back coating N/A 35 - 39
CLIMAPLUS
control airborne particles for Class 10M-100M Class 10M-100M
stringent clean air environments (perforated) (perforated)
0.55-0.65 35 - 39
Class 100 Class 10M-100M

Eclipse™ Non-perforated, high NRC and 0.65 - 0.75 35 - 39

CLIMAPLUS stain resistant through patented
technology.
Medium texture for added visual
appeal

Impressions™ Light micro-fissures for a cleaner 0.50 - 0.60 33 - 39

CLIMAPLUS whiter appearance. Good mid-range
acoustics at an economical price.

Mars™ Excellent combination of high NRC, 0.70 - 0.85 35 - 39

CLIMAPLUS good CAC and a smooth white
non-perforated finish. Ideal for open
plan and closed plan projects and
matching into plasterboard ceilings

Micro pin perfs provide a minimalist 0.50 30 - 39

Olympia Micro™
look combined with a fine sand-
CLIMAPLUS
like texture for a cleaner whiter
appearance. Good mid-range
acoustics.

Radar™ Micro-fissures provide a true 0.50 - 0.60 33 - 39

Radar High NRC non-directional texture allowing 0.65 - 0.75 35 - 39
Radar High CAC installation in any direction. Options 0.50 - 0.60 40 - 44
CLIMAPLUS include panels with higher NRC,
CAC or Firecode™ performance.

Radar CLIMAPLUS The Illusion range has face cuts 0.50 - 0.60 35 - 39
Illusions which provide a variety of different
scales and appearances to a ceiling,
while semi-disguising the exposed
grid.

Rock Face™ Hard textured surface on a Firecode 0.50 - 0.60 35 - 39

CLIMAPLUS basemat offer an abuse resistant
panel with good mid-range
acoustics.

22 © 2011 # Refer to product brochures for specific data

DONN Exposed
Grid Systems General Information

Quantities Approximate linear metres of product required in standard metric layout*

Component Linear Metres Pieces
Main Tee m2 x 0.833
1200mm Cross Tee m2 x 1.667
600mm Cross Tee m2 x 0.833
(for 600mm x 600mm module)
Hold Down Clips m2 x 2.778 (1200 x 600)
(if required) m2 x 5.555 (600 x 600)
Top Fixings / Suspension Clips m2 x 0.694
Wire m x .694 x (plenum depth + 400mm)
2

- Alternative Layouts • For alternative construction layouts use the following formulae to calculate linear metres (LM) or pieces (pcs) per square metre (m 2)

Main Tee - 1 ÷ Main Tee centres

1
eg. if MT at 1350mm centres 1.35 = 0.74 LM/m2

Cross Tee - 1 ÷ Cross Tee centres

1
eg. if CT at 400mm centres 0.4
= 2.5 LM/m2

Top Fixings or 1 ÷ span along the Main Tee X span between the Main Tees
Suspension Clips - eg. if along = 1200mm centres and between = 1350mm centres
1
1.2 x 1.35 = 0.617 pcs (fixing or clips)/m2

* Note: These calculations do not allow for wastage, damage or irregularities, but are intended as an informative guideline to assist with
the calculation of product required for a given area (in m2).

Warranty

#Warranty covers USG acoustical ceiling

# panel and USG DONN ® Brand grid systems
ME
L IFETI
against defects in material or manufacturing
workmanship for the useful life of the ceiling
D system, up to a maximum of 30 years.
LIMIRTAENTY See your regional USG Ceiling Systems
W AR Specialist for full warranty details.

Short Specification Supply and install a USG suspended ceiling system as manufactured and supplied by USG Interiors.
System shall comprise of :
• (DONN DX 24mm) / (DONN DXT Centricitee 15mm) two way exposed grid system
• Module shall be (600 x 600) / (1200 x 600) / (other)
• Grid shall have minimum tension values of ____kg and compression values of ____kg
• Wall Angle shall be (MT/ML/MS/MSL/MXT/US 3600) fixed at 600 mm centres maximum
• Installation shall comply with AS/NZS 2785 – Suspended Ceilings - Design and Installation
• Seismic installation shall comply with AS 1170.4 or NZS 1170.5 and USG Seismic Design Guide
• Colour shall be USG (Pacific White) / (other)
• USG ( ) ClimaPlus Acoustical ceiling panel, NRC 0. __ and CAC __ - __ minimum
• Colour shall be USG (Standard White) / (other)
• Plasterboard suspension shall be USG Drywall Grid System

Web Site For other USG product information, and contacts please visit our web site at :

www.usg.co.nzZzz and www.usg.com.au

© 2011
2
 To request literature, samples, a visit from a
USG Ceilings specialist, or for all technical
questions, call your nearest USG office below.

USG Australasia New South Wales Queensland Victoria \ Wellington

Auckland Head Office EG/6-11 Trademark
The following are
Phone:
NewSouth 100 22 21 Phone: (0) 20-2 (0) 0 2 trademarks of USG
Interiors , Inc. or a
Fax: 100   Fax: (0) 20-1 (0) 0 2 related company:
Donn, FirecoDe, Quick
www.usg.com.au [email protected] www.usg.co.nz [email protected] release, usG.