DTCO 1381 Universal Device Rel.2.2

1
DTCO 1381 Universal Device Rel.2.2
Procedure for uploading OEM Parameter Sets (Release 8)

to Universal DTCO® 1381 Rel. 2.2 Devices
Precondition: CTCII has been updated to software version 2.13 (or later) and the
Licence for the universal DTCO® has been uploaded. Also the latest list of OEM
variant parameters has been uploaded <PARA_ZIP_FILE_M15_for_2.2.zip> using
<CONTRAM_01_03.exe> on to your CTCII Version 2.13 (see ‘Uploading OEM
parameters sets to CTC II 020216.pdf’)
There are 6 universal devices based on Release 2.2 (All with IMS ON, Remote HMI
ON, VDO Counter enabled on display and for diagnostics, GeoLoc [Mapping] and data
recording (via CAN) functionality enabled and activated, RDL possible via released front K-
Line):
1381-2214303001 (24V, ADR Zone 2)

Predecessor Rel.2.1: 1381/2210309003T
Features a second, open CAN, D1/D2, A4/A8 with fixed 120 Ohm resistor, v/n profile, white display,
4 dimming presets based on CAN, terminal 15, terminal 58 day/night or terminal 58D
1381-2214303002 (24V, ADR Zone 2)

Features a second, open CAN, D1/D2, A4/A8 without resistor, v/n profile, white display, 4 dimming
presets based on CAN, terminal 15, terminal 58 day/night or terminal 58D
1381-4214302001 (24V, ADR Zone 1)

IMPORTANT: ADR Input on B5 (On predecessor it was D3)
1381-4214302002 (24V, ADR Zone 1)

IMPORTANT: ADR Input on B5 (On predecessor it was D3)
1381-0214203001 (12V)
1381/0214203002T (12V)
Please circulate to all concerned
Continental Automotive Trading UK Ltd Phone +44 121 326 1234 Registered No. 965702 England
36 Gravelly Industrial Park Fax + 44 121 326 1299 Registered Office: 36 Gravelly Industrial Park,
Birmingham www.dtco.co.uk Birmingham B24 8TA 02/11/15
B24 8TA
2
IMPORTANT – How to switch the IMS (Independent Motion Signal) OFF

From 1st October 2012, EU Regulation 1266/2009 requires that in order to detect
manipulation of motion data, information from the KITAS 2+ sensor must be
corroborated by an Independent Motion Signal (IMS) - using a third generation digital
tachograph (i.e. DTCO Rel.2.0 / 2.0a / 2.1). Therefore in a new vehicle, if a digital
tachograph is activated on or after the 1st October 2012, it MUST be a third
generation type of digital tachograph (i.e. DTCO Rel.2.0 / 2.0a / 2.1).
Please note that there is no requirement to retrospectively apply this regulation.

Thus if a vehicle had originally been fitted with a 1st generation or 2nd generation
digital tachograph, the same type of DTCO can be retrofitted or a third generation
digital (i.e. DTCO Rel.2.0 / 2.0a / 2.1) can be installed with the IMS OFF.
The Universal device OEM variant parameters are supplied with the IMS ON and
therefore it is important for most retrofit applications to switch the IMS OFF.
In order to switch the IMS OFF, please select ‘SWITCH_IMS_OFF’ after you have
uploaded the required OEM parameter set, via Installation Data (see below)
CTC II – Switching the IMS OFF

The Universal device OEM variant parameters are supplied with the IMS ON and
therefore it is important for most retrofit applications to switch the IMS OFF.
After you have uploaded the required OEM parameter set, select the following:
Programming Installation Data IMS Signal Source
Select [OFF] ENTER
Representation of the loaded Parameter set

All DTCO 1381.xxxxxxxxxx Rel. 2.0, 2.0a, 2.0U1, 2.1 and 2.2
CTCII-Display Original OEM- Usage

DTCO:
In first line of each parameter list
PARA_ZIP_FILE_M15_for_2.2 All DTCO 2.2 (independent of which DTCO device
you have already connected) you
will always see the name
representing the parameter set.
B24 8TA
3
OEM DTCO® 1381 Rel.2.1 (2.0, 2.0a, 2.1) devices that can be
emulated by the Universal DTCO® 1381 Rel.2.2 are as follows:
1381-2214303001 Universal DTCO® 2.2 (24v ADR Zone 2 with R):

CTCII-Display Original OEM-DTCO: Usage
ALEXANDER DENNIS 1381.1051009008 UK Bus manufacturer

DAF XF/CF/LF 1381.2051109005 Series XF/CF/LF
DENNIS EAGLE 1381.1010109008 UK Truck manufacturer in
EVOBUS 1381.1070109009 SETRA and Mercedes buses
HINO 1381.1060109002 Japanese Light and CW
Truck Manufacturer
IVECO EUROCARGO 1381.1072109005 Stralis, Eurocargo Trakker
IVECO STRALIS NEW 1381.1212109004 Phase lift STRALIS
KENWORTH 1381.2050309002 American Truck
MAN TG 1381.2051009004 TGX, TGM, TGL
MERCEDES AC/AX/AT 1381.2070009004 ACTROS, AXOR, ATEGO,
UNIMOG
NISSAN ATLEON wR 1381.1101009001 Atleon
RENAULT D-TRUCK 1381.2052309010 New Truck Generation
(heavy class)
RENAULT MAG EUR3 wR 1381.2052300028 Magnum, Kerax, Premium,
Midlum EURO3
RENAULT T-TRUCK 1381.1212309007 New Truck Generation
(medium class)
SCANIA 1381.1071409001 P-, G-, R-Series
SOLARIS 1381.1070209001 Polish Bus Manufacturer
SOR 1381.1070009006 Polish Bus Manufacturer
TEMSA 1381.1071009004 Turkish Bus Manufacturer
VAN HOOL 1381.1070009004 Belgian Bus Manufacturer
VDL BUS 1381.1070109008 Dutch Bus Manufacturer
VDO UNIVERSAL 1381.2214303001 Reset to factory setting
VISEON BUS 1381.1051009004 German Premium Bus
Manufacturer
VOLVO FL06 mR 1381.2012000023 FE/FL EURO3
VOLVO NEW FE/FL 1381.2012309010 New Truck Generation
(medium class)
VOLVO NEW FH 1381.1232309007 New Truck Generation
(heavy class)
VOLVO FH/FM 1381.2012009005 Series FM/FH (TAE2)
B24 8TA
4
1381-2214303002 Universal DTCO® 2.2 (24v ADR Zone 2 without R):
ACTROS NEW GEN 1381.2010009005 New ACTROS, AROCS,

ANTOS
CHINA Kinglong 1381.1070009005 Chinese Bus importer, e.g.
Kinglong, Yutong, …
EVOBUS B2E 1381.1010109009 New SETRA / Mercedes Bus
platform
ISUZU 1381.1050209002 NQR, NPR
KENWORTH 1381.2050309002 American Truck
MITSUBISHI 1381.1070109011 Canter
NISSAN ATLEON woR 1381.1101009001 Atleon
RENAULT MAG EU3 woR 1381.2052300028 Magnum, Kerax, Premium,
Midlum EURO3 (without CAN
Resistor)
RENAULT MAGNUM 1381.2052309009 Magnum, Kerax, Premium,
Midlum (TAE2)
SOLARIS 1381.1070209001 Polish Bus Manufacturer
VOLVO FL06 oR 1381.2012000023 FE/FL EURO3 (without CAN
Resistor)
1381-4214302001 Universal DTCO® 2.2 (24v ADR Zone 1 with R) (Battery

Master Switch input MUST be on B5):

IVECO EUROCARGO 1381.4072109003 Stralis, Eurocargo Trakker
(ADR) IMPORTANT: The original
OEM DTCO, PIN D3 is used for the
Battery Master Switch input. You
MUST change the wire from D3 to
B5
IVECO STRALIS NEW 1381.4212109004 Phase lift STRALIS (ADR)
IMPORTANT: The original OEM
DTCO, PIN D3 is used for the
Battery Master Switch input. You
MUST change the wire from D3 to
B5
RENAULT T-Truck 1381.4212309007 New Truck Generation (heavy
class, ADR) IMPORTANT: The
original OEM DTCO, PIN D3 is used
for the Battery Master Switch input.
You MUST change the wire from D3
to B5
SCANIA ADR Z1-B5 1381.4071409004 SCANIA P-, G-, R-Series ADR
VOLVO NEW FH/FM 1381.4232309007 New Truck Generation (heavy
class, ADR) IMPORTANT: The
original OEM DTCO, PIN D3 is used
for the Battery Master Switch input.
You MUST change the wire from D3
to B5
B24 8TA
5
1381-4214302002 Universal DTCO® 2.2 (24v ADR Zone 1 without R)

(Battery Master Switch input on B5):
1381-0214203001 Universal DTCO® 2.2 (12v with R):
RENAULT MASTER III 1381.0111409010 REN Master III, NIS NV400

and OPEL Movano
VDO UNIVERSAL 1381.0214203001 Reset to factory settings
1381-0214203002 Universal DTCO® 2.2 (12v without R):
FENDT VARIO 1381.0010209002 Tractors (AGCO-Corporation)

FIAT DUCATO NEW 1381.0111009005 From model year 2012
FIAT DUCATO 1381.0111009001 Phase out model of Ducato
FORD RANGER 1381.0250309003 SUV and Pickup
FORD RANGER NEW 1381.0250309003 SUV and Pickup 2014
(Iceblue lighting)
FORD TRANSIT 1381.0070309004 Phase out model with
day/night dimming
FORD TRANSIT NEW GEN 1381.0250309006 From model year 2013
(Icebule lighting)
FORD TRANSIT RHEO 1381.0070309003 Phase out model with
Rheostat dimming
HMC HYUNDAI EU VAN 1381.0250009002 New: EU Van
IVECO DAILY M2009 1381.0111109008 Phase out model

IVECO DAILY M2012 1381.0111109010 From model year 2012
(Summer 2011)
IVECO DAILY M2014 1381.0111109009 From model year 2014
(Summer 2013)
MERCEDES SPRINTER 1381.0010009007 All Sprinter versions from
2007 (NCV3)
MERCEDES VITO 1381.0010009009 (NCV2, Series 639)
MITSUBISHI 1381.0070109003 Canter
NISSAN CABSTAR 1381.0101009004 Atlas, Cabstar, Maxity
RENAULT NISSAN OPEL 1381.0111409011 REN Trafic, NIS Primastar
and OPEL Vivaro
TEMSA 1381.0071309004 Turkish Bus manufacturer
VW CRAFTER 1381.0121009007 Exclusively only Crafter, not
T5 ! !
B24 8TA
6
Other Programming Possibilities

CTCII-Display Target DTCO Usage
WeeklyDriveTime OFF Rel.2.1 and Calculation of Weekly Driving Time is deactivated.

higher Recommended for all drivers on buses and
coaches who drive according to 12-day-exception-
EC 1073/2009 regulation
VDO Counter Mask during driving keeps
unchanged
If vehicle is stationary:
Display: Weekly Driving Time
Display: Status
WeeklyDriveTime ON Rel.2.1 and VDO Counter
higher If vehicle is stationary:
Display: Weekly Driving Time
Display: Status
DCDL Reminder 7 Rel.2.1 and Drivercard Download reminder functionality
higher Will be set to 7 days (7 days (and less) before a
Driver card is required to be downloaded at the
latest, the driver gets reminded every card ejection)
DCDL Reminder OFF Rel.2.1 and Drivercard Download reminder functionality
higher completely switched off!
(This is recommended if the customer uses
drivercard download tools which do not fulfil the
exact requirements given in Annex 1b chapter 2.65
according Parameter: ‘LastCardDownload’).
GEOLOC Adapt All Rel.2.0 and Increase of time tolerance regarding IMS Fault
higher
VDO LOGO All Rel.1.3a Standard VDO Logo will be uploaded to DTCO
and higher
B24 8TA
7
Other Programming Possibilities – Vehicle data logging

(Geologging + 4 CAN messages)
CTCII-Display Target DTCO Usage
GEOLOG BASIC CAN1 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
GEOLOG BASIC CAN2 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
GEOLOG GENERIC CAN1 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
GEOLOG GENERIC CAN2 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
GEOLOG INTENSE CAN1 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
GEOLOG INTENSE CAN2 All Rel. 2.2 For all 1381.* with Rel. 2.2 SW (V 2223)
Other Programming Possibilities – (Calibration behaviour)

Target DTCO Usage
ACTIVATION ONLY All Rel.2.2 For all 1381 with Rel. 2.2 SW (V 2223) If
set, only activation purpose (1) will be
generated - Mandatory in countries
where such a national regulation exists:
i.e France (case 1)
ACTIV.& FIRST CALIB. All Rel.2.2 For all 1381 with Rel. 2.2 SW (V 2223) If
set, activation purpose (1), first
calibration (2) and installation (3) will be
generated.
If a UNIVERSAL device is used, not
necessary because set per default
All others (case 2)
Which cases exist in workshops?
Case 1) National exceptions, example: France

Universal device will be parameterised first time with any OEM-Parameter set. The last step
and action is to perform : ACTIVATION ONLY !
It means:
With next workshop session you can only generate or perform an activation (1) First
calibration (2) and (3) cannot be generated during this session.
To make calibration purposes (2) and (3), you have to eject workshop card and re-insert it
again. Then you have to measure the ‘w’ and ‘l’ and program it.
Case 2) No national restrictions apply:
In ‘production’ state you can upload any OEM- parameter set.

So you have the possibility to perform and measure in one workshop session all necessary
calibration records (1), (2) and (3) in one session. So you have more or less the same
situation as the truck manufacturer will have in their production to generate ‘activation &first
calibration’, in one process!
B24 8TA
8
Other Programming Possibilities – (Pre-overspeed alert behaviour )

Target DTCO Usage
PreOverspd Standard All Rel.2.x All 1381 with Rel.2.x SW (V 2230-V

2223)
PreOverspd Alternat All Rel.2.x All 1381 with Rel.2.x SW (V 2230-V
2223)
Special Programming for OE Dedicated Devices
FIAT Ducato with initially equipped DTCO from factory

There are FIAT Ducato models in the field, which have two different types of CAN
architectures. These are differentiated by the IMS Settings (Second independent
motion signal). In case of device exchange the ‘FIAT DUCATO NEW IMS’ may be
required to be executed.
FIAT DUCATO IMS 1381.0111009005 Standard IMS (approx. 75%

of vehicles)
FIAT DUCATO NEW IMS 1381.0111009005 ‘Adapted’ IMS (approx. 25%
of vehicles)
FORD Transit with original equipped DTCO from stock

Currently FORD has approved DTCO Rel. 2.1: 1381.0250309006 and this will be
installed uniformly in the current FORD Transit.
It will also serve as a substitute for all installed DTCO’s in existing FORD Models.
Therefore to be able to guarantee 100% backwards compatibility, adaptations must
be done.
Therefore for older Transit and Ford Ranger-Models, the DTCO: 1381.0250309006
must be ‘recalibrated’ as a substitute.
FORD RANGER IMS 1381.0250309006 IMS for Ford Ranger (Year 2012/2013)
FORD RANGER NEW IMS 1381.0250309006 IMS for Ford Ranger (Year 2013/2014)
FORD TRANSIT NEW 1381.0250309006 Reset to FORD Transit NEW
FORD TRANSIT OLD 1381.0250309006 Standard IMS and A2-Dimming for
Transit
FORD TRANSIT RHEO 1381.0250309006 Standard IMS for Dimming Rheostat for
Transit
FORD CAN GeoLoc 1381.0250309006 Standard setting for CAN1 (Connection
possibility GeoLoc)
B24 8TA
9
Examples:
a) In an older Ford Transit a DTCO 1.4 1381.0070300018 has failed. As a

substitute only the DTCO 2.1:1381.0250309006 is available. To ensure 100%
compatibility, using the CTCII ‘FORD TRANSIT OLD’ must be parameterised.
b) In a FORD Ranger 2014 a DTCO is required to be retrofitted. The DTCO

2.1:1381.0250309006 must be parameterised as ‘FORD RANGER NEW IMS’
Procedure for Uploading an OEM Parameter Set:

You can parameterise all known UNIVERSAL-DTCO® 2.2 by uploading ZIP file:
<PARA_ZIP_FILE_M15_for_2.2.zip> using <CONTRAM_01_03.exe> on your
CTCII with Version 2.13 or later
Step 1 – Workshop Card Insertion

Insert Workshop Card into DTCO unit so that it is in Calibration Mode.
Step 2 – Connect CTC II to DTCO

Switch on and connect the CTC II to the DTCO unit using the programming cable
B24 8TA
10
Step 3 - Programming a DTCO® Rel.2.2 universal device to run like

an OEM-variant
a) Scroll and Select ‘PROGRAMMING’
b) Then Scroll and Select ‘SAVE TCO DATA’
c) Then Scroll and Select ‘WRITE UNIV.DTCO’
d) Select the applicable OEM variant parameter set (See below an example for
selecting DAF)
e) When the OEM variant parameter set has been stored in the DTCO, a ‘VDO’ logo
printout confirmation will be shown.
Please Note that if you load more than one OEM variant parameter set, the display
may indicate ‘ERROR, TCO – NEG. RESPONSE’. To start the process of re-
programming a further OEM parameter, program the DTCO back to ‘VDO
UNIVERSAL’ (i.e. factory re-set)
Step 4 – If applicable switch IMS OFF (see page 2)
B24 8TA
11
ADR Zone 1 Vehicles and DTCO Rel.2.2

IMPORTANT: All OEM devices shown below, provide their ADR Input at Pin D3. If you
are replacing the existing DTCO with a UNIVERSAL DTCO Rel. 2.2 (ADR Input
normally at B5) please ensure that the DTCO® Pin B5 is connected to the battery
master switch safely. This can be done by unpinning D3 and moving the wire to B5
input.
CTCII Display Original OEM Vehicle Type

DTCO
IVECO EUROCARGO 1381.4072109003 Stralis,
Eurocargo
Trakker (ADR)
Since 2008
IVECO STRALIS NEW 1381.4212109004 Phaselift

STRALIS (ADR)
Since 2014
RENAULT T-Truck 1381.4212309007 New Truck

Generation
(Heavy class,
ADR)
Since 2014
VOLVO NEW FH/FM 1381.4232309007 New Truck

Generation
(Heavy class,
ADR)
Since 2013
B24 8TA

DTCO 1381 Universal Device Rel.2.2

Uploaded by

Copyright:

Available Formats

DTCO 1381 Universal Device Rel.2.2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DTCO 1381 Universal Device Rel.2.2

Uploaded by

Copyright:

Available Formats

What are the different types of universal DTCO devices mentioned?

What are the different types of universal DTCO devices mentioned?

What is the procedure for uploading an OEM parameter set?

What is the procedure for uploading an OEM parameter set?

1

DTCO 1381 Universal Device Rel.2.2

Procedure for uploading OEM Parameter Sets (Release 8)

1381-2214303001 (24V, ADR Zone 2)

1381-2214303002 (24V, ADR Zone 2)

1381-4214302001 (24V, ADR Zone 1)

1381-4214302002 (24V, ADR Zone 1)

Please circulate to all concerned

IMPORTANT – How to switch the IMS (Independent Motion Signal) OFF

Please note that there is no requirement to retrospectively apply this regulation.

CTC II – Switching the IMS OFF

Programming Installation Data IMS Signal Source

Select [OFF] ENTER

Representation of the loaded Parameter set

CTCII-Display Original OEM- Usage

Please circulate to all concerned

1381-2214303001 Universal DTCO® 2.2 (24v ADR Zone 2 with R):

ALEXANDER DENNIS 1381.1051009008 UK Bus manufacturer

Please circulate to all concerned

1381-2214303002 Universal DTCO® 2.2 (24v ADR Zone 2 without R):

CTCII-Display Original OEM-DTCO: Usage

ACTROS NEW GEN 1381.2010009005 New ACTROS, AROCS,

1381-4214302001 Universal DTCO® 2.2 (24v ADR Zone 1 with R) (Battery

CTCII-Display Original OEM-DTCO: Usage

Please circulate to all concerned

1381-4214302002 Universal DTCO® 2.2 (24v ADR Zone 1 without R)

CTCII-Display Original OEM-DTCO: Usage

VDO UNIVERSAL 1381.4214302002 Reset to factory setting

1381-0214203001 Universal DTCO® 2.2 (12v with R):

CTCII-Display Original OEM-DTCO: Usage

RENAULT MASTER III 1381.0111409010 REN Master III, NIS NV400

1381-0214203002 Universal DTCO® 2.2 (12v without R):

CTCII-Display Original OEM-DTCO: Usage

FENDT VARIO 1381.0010209002 Tractors (AGCO-Corporation)

IVECO DAILY M2009 1381.0111109008 Phase out model

Please circulate to all concerned

Other Programming Possibilities

WeeklyDriveTime OFF Rel.2.1 and Calculation of Weekly Driving Time is deactivated.

Display: Weekly Driving Time

Display: Weekly Driving Time

Please circulate to all concerned

Other Programming Possibilities – Vehicle data logging

Other Programming Possibilities – (Calibration behaviour)

Which cases exist in workshops?

Case 1) National exceptions, example: France

Case 2) No national restrictions apply:

In ‘production’ state you can upload any OEM- parameter set.

Please circulate to all concerned

Other Programming Possibilities – (Pre-overspeed alert behaviour )

PreOverspd Standard All Rel.2.x All 1381 with Rel.2.x SW (V 2230-V

Special Programming for OE Dedicated Devices

FIAT Ducato with initially equipped DTCO from factory

CTCII-Display Original OEM-DTCO: Usage

FIAT DUCATO IMS 1381.0111009005 Standard IMS (approx. 75%

FORD Transit with original equipped DTCO from stock

CTCII-Display Original OEM-DTCO: Usage