B360M DS3H Motherboard Manual

B360M DS3H
User's Manual
Rev. 1001
For more product details, please visit GIGABYTE's website.
To reduce the impacts on global warming, the packaging materials of this product
are recyclable and reusable. GIGABYTE works with you to protect the environment.
Motherboard
B360M DS3H
Motherboard
B360M DS3H
Feb. 9, 2018
Feb. 9, 2018
Copyright
© 2018 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or
by any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means
the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard
BIOS, drivers, or when looking for technical information.
Example:
Table of Contents
B360M DS3H Motherboard Layout..................................................................................4
Chapter 1 Hardware Installation......................................................................................5

1-1 Installation Precautions..................................................................................... 5
1-2 Product Specifications....................................................................................... 6
1-3 Installing the CPU............................................................................................. 9
1-4 Installing the Memory........................................................................................ 9
1-5 Installing an Expansion Card.......................................................................... 10
1-6 Back Panel Connectors................................................................................... 10
1-7 Internal Connectors......................................................................................... 12
Chapter 2 BIOS Setup...................................................................................................20

2-1 Startup Screen................................................................................................ 20
2-2 The Main Menu............................................................................................... 21
2-3 M.I.T................................................................................................................ 22
2-4 System............................................................................................................ 28
2-5 BIOS................................................................................................................ 29
2-6 Peripherals...................................................................................................... 32
2-7 Chipset............................................................................................................ 35
2-8 Power.............................................................................................................. 36
2-9 Save & Exit...................................................................................................... 38
Chapter 3 Appendix.......................................................................................................39
3-1 Installing an Intel® Optane™ Memory............................................................... 39
3-2 Drivers Installation........................................................................................... 40
Regulatory Statements............................................................................................... 41
Contact Us................................................................................................................. 43
-3-
B360M DS3H Motherboard Layout
DDR4_4
DDR4_3
DDR4_1
DDR4_2
ATX_12V_2X4 CPU_FAN
KB_MS_USB
SYS_FAN1 ATX
LGA1151
VGA
DVI
HDMI
R_USB30
USB30_LAN
SATA3 32 10
M2M_32G
AUDIO 80 60 42
Realtek® B360M DS3H
F_USB30
GbE LAN
PCIEX16
BAT
iTE® M_BIOS
Super I/O B_BIOS
PCIEX1 Intel® B360 SATA3 45
PCIEX4
CODEC LED_C SYS_FAN2
SPDIF_O F_USB1
TPM
COM F_USB2 F_PANEL

F_AUDIO LPT CLR_CMOS
Box Contents
55 B360M DS3H Motherboard
55 Motherboard driver disk 55 Two SATA cables
55 User's Manual 55 I/O Shield
* The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
-4-
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•• Before connecting or unplugging the power supply cable from the motherboard, make sure
the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature or wet environment.
•• Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
•• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation
and/or grounding instructions.
-5-
1-2 Product Specifications
CPU Support for 8th Generation Intel® Core™ i7 processors/Intel® Core™ i5 processors/
Intel® Core™ i3 processors/Intel® Pentium® processors/Intel® Celeron® processors
in the LGA1151 package
(Go to GIGABYTE's website for the latest CPU support list.)
L3 cache varies with CPU
Chipset Intel® B360 Express Chipset
Memory 4 x DDR4 DIMM sockets supporting up to 64 GB of system memory
Dual channel memory architecture
Support for DDR4 2666/2400/2133 MHz memory modules
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in
non-ECC mode)
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
Support for Extreme Memory Profile (XMP) memory modules
* To support 2666 MHz or XMP memory, you must install an 8th Generation Intel®
Core™ i7/i5 processor.
(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)
Onboard Integrated Graphics Processor-Intel® HD Graphics support:
Graphics - 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz
- 1 x DVI-D port, supporting a maximum resolution of 1920x1200@60 Hz
* The DVI-D port does not support D-Sub connection by adapter.
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@30 Hz
* Support for HDMI 1.4 version and HDCP 2.2.
Support for up to 3 displays at the same time
Maximum shared memory of 1 GB
Audio Realtek® ALC887 codec
High Definition Audio
2/4/5.1/7.1-channel
* T
o configure 7.1-channel audio, you have to use an HD front panel audio module
and enable the multi-channel audio feature through the audio driver.
Support for S/PDIF Out
LAN Realtek® GbE LAN chip (10/100/1000 Mbit)
Expansion Slots 1 x PCI Express x16 slot, running at x16
* For optimum performance, if only one PCI Express graphics card is to be installed,
be sure to install it in the PCIEX16 slot.
1 x PCI Express x4 slot
1 x PCI Express x1 slot
(All of the PCI Express slots conform to PCI Express 3.0 standard.)
Storage Interface Chipset:
- 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280 SATA and PCIe
x4/x2 SSD support)
- 6 x SATA 6Gb/s connectors
Intel® Optane™ Memory Ready
-6-
USB Chipset:
- 6 x USB 3.1 Gen 1 ports (4 ports on the back panel, 2 ports available through
the internal USB header)
- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through
the internal USB headers)
Internal 1 x 24-pin ATX main power connector
Connectors 1 x 8-pin ATX 12V power connector
1 x CPU fan header
2 x system fan headers
1 x RGB LED strip header
1 x M.2 Socket 3 connector
6 x SATA 6Gb/s connectors
1 x front panel header
1 x front panel audio header
1 x S/PDIF Out header
1 x USB 3.1 Gen 1 header
2 x USB 2.0/1.1 headers
1 x Trusted Platform Module (TPM) header (2x6 pin, for the GC-TPM2.0_S
module only)
1 x serial port header
1 x parallel port header
1 x Clear CMOS jumper
Back Panel 1 x PS/2 keyboard/mouse port
Connectors 1 x D-Sub port
1 x DVI-D port
1 x HDMI port
4 x USB 3.1 Gen 1 ports
2 x USB 2.0/1.1 ports
1 x RJ-45 port
3 x audio jacks
I/O Controller iTE® I/O Controller Chip
Hardware Voltage detection
Monitor Temperature detection
Fan speed detection
Overheating warning
Fan fail warning
Fan speed control
* Whether the fan speed control function is supported will depend on the cooler you
install.
BIOS 2 x 128 Mbit flash
Use of licensed AMI UEFI BIOS
Support for DualBIOS™
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
-7-
Unique Features Support for APP Center
* Available applications in APP Center may vary by motherboard model. Supported
functions of each application may also vary depending on motherboard specifications.
- 3D OSD
- @BIOS
- AutoGreen
- Cloud Station
- EasyTune
- Fast Boot
- Game Boost
- ON/OFF Charge
- Platform Power Management
- RGB Fusion
- Smart Backup
- Smart Keyboard
- Smart TimeLock
- Smart HUD
- System Information Viewer
- USB Blocker
- V-Tuner
Support for Q-Flash
Support for Xpress Install
Bundled
Norton® Internet Security (OEM version)
Software
Operating
Support for Windows 10 64-bit
System
Form Factor Micro ATX Form Factor; 22.6cm x 20.5cm
* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without
prior notice.
Please visit GIGABYTE's website for support lists of CPU, memory modules, SSDs, and M.2 devices.
Please visit the Support\Utility List page on GIGABYTE's website to download the latest version
of apps.
-8-
1-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
•• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
•• Apply an even and thin layer of thermal grease on the surface of the CPU.
•• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics
card, memory, hard drive, etc.
Installing the CPU
Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.
LGA1151 CPU Socket LGA1151 CPU
Notch Notch
Alignment Key Alignment Key
Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU
Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load
plate automatically during the process of re-engaging the lever after you insert the CPU.
1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory
is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
Please visit GIGABYTE's website for details on hardware installation.
-9-
The four DDR4 memory sockets are divided into two channels and each channel has two memory sockets as
following:

Channel A: DDR4_2, DDR4_4

Channel B: DDR4_1, DDR4_3
Dual Channel Memory Configurations Table
DDR4_4 DDR4_2 DDR4_3 DDR4_1
Two Modules -- DS/SS -- DS/SS
DS/SS -- DS/SS --
Four Modules DS/SS DS/SS DS/SS DS/SS
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory
of the same capacity, brand, speed, and chips be used.
1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.
1-6 Back Panel Connectors
USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
D-Sub connection to this port.
DVI-D Port (Note)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
DVI-D connection to this port.
(Note) The DVI-D port does not support D-Sub connection by adapter.
•• When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
- 10 -
HDMI Port
The HDMI port supports HDCP 2.2 and Dolby TrueHD and DTS HD Master
Audio formats. It also supports up to 192KHz/16bit 8-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The maximum supported
resolution is 4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor
being used.
•• To set up a triple-display configuration, you must install motherboard drivers in the operating
system first.
•• After installing the HDMI/DisplayPort device, make sure to set the default sound playback
device to HDMI/DisplayPort. (The item name may differ depending on your operating system.)
USB 3.1 Gen 1 Port
The USB 3.1 Gen 1 port supports the USB 3.1 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Connection/ Connection/Speed LED:
Speed LED Activity LED Activity LED:
State Description State Description
Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring
Green 100 Mbps data rate Off No data transmission or receiving is occurring
Off 10 Mbps data rate
LAN Port
Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out/Front Speaker Out (Green)
The line out jack.
Mic In/Center/Subwoofer Speaker Out (Pink)
The Mic in jack.
Audio Jack Configurations:

Headphone/
Jacks 4-channel 6-channel 8-channel
2-channel
Line In/Rear Speaker Out a a a
Line Out/Front Speaker Out a a a a
Mic In/Center/Subwoofer
a a
Speaker Out
Front Panel Line Out/
a
Side Speaker Out
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the
multi-channel audio feature through the audio driver.
Please visit GIGABYTE's website for details on configuring the audio software.
- 11 -
1-7 Internal Connectors
4 1 3
11
7
16
6
10
9 13 14 5 12 4 15 17 8
1) ATX_12V_2X4 10) SPDIF_O

2) ATX 11) F_USB30
3) CPU_FAN 12) F_USB1/F_USB2
4) SYS_FAN1/2 13) COM
5) LED_C 14) LPT
6) SATA3 0/1/2/3/4/5 15) TPM
7) M2M_32G 16) BAT
8) F_PANEL 17) CLR_CMOS
9) F_AUDIO
Read the following guidelines before connecting external devices:

•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 12 -
1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
on the motherboard. Before connecting the power connector, first make sure the power supply is turned
off and all devices are properly installed. The power connector possesses a foolproof design. Connect the
power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.
ATX_12V_2X4:
Pin No. Definition Pin No. Definition
5 8 1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin 12V)
1 4 2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin 12V)
ATX_12V_2X4 3 GND 7 +12V
4 GND 8 +12V
ATX:
12 24 1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 NC
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
ATX)
1 13 12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX)
ATX)
ATX
- 13 -
3/4) CPU_FAN/SYS_FAN1/2 (Fan Headers)
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.
When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is
the ground wire). The speed control function requires the use of a fan with fan speed control design. For
optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
Pin No. Definition
1 1
1 GND
CPU_FAN/SYS_FAN1 SYS_FAN2 2 Voltage Speed Control
3 Sense
4 PWM Speed Control
•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
•• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
5) LED_C (RGB LED Strip Header)
The header can be used to connect a standard 5050 RGB LED strip (12V/G/R/B), with maximum power
rating of 2A (12V) and maximum length of 2m.
1
Pin No. Definition
1 12V
2 G
3 R RGB
LED Strip
4 B
PORT
DEBUG 1
12V
Connect your RGB LED strip to the header. The power pin (marked with a triangle on the plug) of
the LED strip must be connected to Pin 1 (12V) of the digital LED strip header. Incorrect connection
may lead to the damage of the LED strip.
For how to turn on/off the lights of the LED strip, refer to the instructions on in Chapter 2, "BIOS
Setup," "Peripherals."
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent
DEBUGdamage to the devices.
PORT
6) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
DEBUG
PORT
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device.
7 7
Pin No. Definition
1 GND
SATA3 2 TXP
1 0
3 TXN
3 2
4 GND
5 RXN
6 RXP
1 1 7 GND
SATA3 1 To enable hot-plugging for the SATA ports, refer to Chapter

7
4 2, "BIOS Setup," "Peripherals\SATA And RST Configuration,"
5 1 7 for more information.
- 14 -
_0 F
7) M2M_32G (M.2 Socket 3 Connector)

The M.2 connector supports M.2 SATA SSDs and M.2 PCIe SSDs.
80 60 42
Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole
for the M.2 SSD to be installed and then screw the nut first.
Step 2: _3 U
Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it with the screw.
Select the proper hole for the M.2 SSD to be installed and refasten the screw and nut.
Installation Notices for the M.2 and SATA Connectors:

3 Due to the limited number of lanes provided by the Chipset, the availability of the SATA connectors may be
affected by the type of device installed in the M.2 connector. The M2M_32G connector shares bandwidth
with the SATA3 5 connector. Refer to the following table for details.
Connector
Type of SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5
M.2 SSD
M.2 SATA SSD a a a a a r
M.2 PCIe SSD a a a a a a
No M.2 SSD Installed a a a a a a
a: Available, r: Not available
- 15 -
8) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
Power LED Power Switch Speaker
•• PLED/PWR_LED (Power LED):
System Status LED Connects to the power status indicator
PLED+
on the chassis front panel. The LED is on

PW+
SPEAK+ S0 On
SPEAK-
when the system is operating. The LED is
PLED-
S3/S4/S5 Off
PW-
NC
NC
off when the system is in S3/S4 sleep state
S S U
F_ 2 20 F_ or powered off (S5).
1 19
•• PW (Power Switch):
3 2 1
PWR_LED+
PWR_LED-
PWR_LED-
Connects to the power switch on the chassis front panel. You may
HD-
RES+
CI+
configure the way to turn off your system using the power switch (refer
HD+
RES-
CI-
to Chapter 2, "BIOS Setup," "Power," for more information).

Hard Drive Reset Power LED •• SPEAK (Speaker):
Activity LED Switch
Chassis Intrusion Connects to the speaker on the chassis front panel. The system reports
Header system startup status by issuing a beep code. One single short beep
will be heard if no problem is detected at system startup.
•• HD (Hard Drive Activity LED):
SS
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
1
•• RES (Reset Switch):

_S
1
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
1
if the computer freezes and fails to perform a normal restart.

•• CI (Chassis Intrusion Header): _ B S_
B
Connects to the chassis intrusion switch/sensor on the chassis that can detect if theBchassis cover has
S been removed. This function requires a chassis with a chassis intrusion switch/sensor.
•• NC : No Connection.
1 2 3
1 2 3
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive
S B_ activity LED, speaker and etc. When connecting your chassis
1 2 3
1 2 3
front panel module to this header, make

B sure the wire assignments and the pin assignments are
matched correctly.
9) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports High Definition audio (HD). You may connect your chassis front
panel audio module to this header. Make _sure
S
the wire assignments of the module connector match the
pin assignments of the motherboard header.
S_ Incorrect connection between the module connector and the
motherboard header will make the device _unable to work or even damage it.
B
9 1 1 MIC2_L 6 Sense
_ U
U 10 2 2_ GND 7 FAUDIO_JD
F
_ _ 3 3 B MIC2_R 8 No Pin
4 NC 9 LINE2_L
5 LINE2_R 10 Sense
F_USB3 F
Some chassis provide a front panel audio module that has separated connectors on each wire instead
_ of a single plug. For information about connecting the front panel audio module that has different wire
_0
assignments, please contact the chassis manufacturer.
_ _B _ - 16 -
_ F
_
_ _
3
_
_B
S F_
10) SPDIF_O (S/PDIF Out Header)
This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion
cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and
sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for
digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display
F_USB3 F
to the graphics card and have digital audio output from the HDMI display at the same time. For information
S_
about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.
_
_ U
_ S
_
B
B
1 Pin No. Definition
1 5VDUAL
2 No Pin
3 SPDIFO
4 GND
F_USB30 F_ U F_
11) F_USB30 (USB 3.1 Gen 1 Header)
The header conforms to USB 3.1 Gen 1 and USB 2.0 specification and can provide two USB ports. For
purchasing the optional 3.5" front panel that provides two USB 3.1 Gen 1 ports, please contact the local
dealer.
1 VBUS 11 D2+
_3
20 1
2 SSRX1- 12 D2-
_0
3 SSRX1+ 13 GND
_ F
_0
F
U
4 GND 14 SSTX2+
F
B SS
B_ 5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND
1
11 10
7 GND 17 1 SSRX2+ _S
8 D1- 18 SSRX2-
1
9 D1+ 19 VBUS
10 NC 20 No Pin
S
1 2 3
1 2 3
12) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
1 2 3
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
1 2 3
9 1 Pin No. Definition Pin No. Definition

1 Power (5V) 6 USB DY+
10 2 2 Power (5V) 7 GND
3 USB DX- 8 GND
4 USB DY- 9 No Pin
5 USB DX+ 10 NC
•• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB 2.0/1.1 header.
B SS U
•• Prior
S 3 to installing the USB bracket, beSsure to turn off your computer and unplug the power
_ _
cord
3
from the power outlet to prevent damage to the USB bracket.
- 17 -
S _
S F
_
_ _B _
S S U
F_
3 2 1
13) COM (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional
COM port cable, please contact the local dealer.

9 1 1 NDCD- 6 NDSR-
2 NSIN 7 NRTS-
10 2 3 NSOUT 8 NCTS-
DEBUG 4 NDTR- 9 NRI-
PORT _
5 GNDB S_ 10 No Pin
B B
14) LPT (Parallel Port Header)

S B_
The LPT headerBcan provide one parallel port via an optional LPT port cable. For purchasing the optional
LPT port cable, please contact the local dealer. S
S
1 STB- 14 GND
_ S 2 AFD- 15 PD6
3 PD0 16 GND
25 S_ 1
_ 4 ERR- 17 PD7
B 5 PD1 18 GND
26 2
6 INIT- 19 ACK-
7 PD2 20 GND
_ U
_
8 SLIN- 21 BUSY
F
_ _ 3 B 9 PD3 22 GND
10 GND 23 PE
11 PD4 24 No Pin
F_USB3 F 12 GND 25 SLCT
13 PD5 26 GND
_0
15) TPM (Trusted Platform Module Header)

You may_ connect a TPM (Trusted Platform Module) to this header.
_ _B
_ F
11 1 1 LAD0 7 LAD3
2 VCC3 8 GND
12 2 3 LAD1 9 LFRAME
4 No Pin 10 NC
5 LAD2 11 _ 0 SERIRQ
F
6 LCLK 12 LRESET
S F_
- 18 -
16) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute. (Or use a
metal object like a screwdriver to touch the positive and negative terminals of the battery
holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
•• Always turn off your computer and unplug the power cord before replacing the battery.
•• Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
•• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
•• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
•• Used batteries must be handled in accordance with local environmental regulations.
17) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear
the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
Open: Normal
Short: Clear CMOS Values
•• Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values.
•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).
- 19 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.
•• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
•• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
(Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clear
CMOS jumper in Chapter 1 for how to clear the CMOS values.)
2-1 Startup Screen

The following startup Logo screen will appear when the computer boots.
(Sample BIOS Version: D3)
Function Keys
There are two different BIOS modes as follows and you can use the <F2> key to switch between the two modes.
The Classic Setup mode provides detailed BIOS settings. You can press the arrow keys on your keyboard to move
among the items and press <Enter> to accept or enter a sub-menu. Or you can use your mouse to select the
item you want. Easy Mode allows users to quickly view their current system information or to make adjustments
for optimum performance. In Easy Mode, you can use your mouse to move through configuration items.
•• When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.
•• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.
- 20 -
2-2 The Main Menu
System Time
Setup Menus
Hardware Informa-
tion
Configuration Items Current Settings Quick Access Bar allows you to enter Easy Mode, select BIOS
default language, configure fan settings, or enter Q-Flash.
Classic Setup Function Keys

<f><g> Move the selection bar to select a setup menu
<h><i> Move the selection bar to select an configuration item on a menu
<Enter> Execute command or enter a menu
<+>/<Page Up> Increase the numeric value or make changes
<->/<Page Down> Decrease the numeric value or make changes
<F1> Show descriptions of the function keys
<F2> Switch to Easy Mode
<F5> Restore the previous BIOS settings for the current submenus
<F7> Load the Optimized BIOS default settings for the current submenus
<F8> Access the Q-Flash utility
<F9> Display system information
<F10> Save all the changes and exit the BIOS Setup program
<F12> Capture the current screen as an image and save it to your USB drive
<Esc> Main Menu: Exit the BIOS Setup program
Submenus: Exit current submenu
- 21 -
2-3 M.I.T.
Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall
system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory
and reduce the useful life of these components. This page is for advanced users only and we recommend you not to
alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings
may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)
`` Advanced Frequency Settings

&& Host Clock Value
Displays the current operating Host Clock frequency.
&& Graphics Slice Ratio (Note)
Allows you to set the Graphics Slice Ratio.
&& Graphics UnSlice Ratio (Note)
Allows you to set the Graphics UnSlice Ratio.
&& CPU Clock Ratio

Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU
being installed.
&& CPU Frequency
Displays the current operating CPU frequency.
&& FCLK Frequency for Early Power On
Allows you to set the FCLK frequency. Options are: Normal(800Mhz), 1GHz, 400MHz. (Default: 1GHz)
`` Advanced CPU Core Settings

&& CPU Clock Ratio, CPU Frequency, FCLK Frequency for Early Power On
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
(Note) This item is present only when you install a CPU that supports this feature. For more information about
Intel® CPUs' unique features, please visit Intel's website.
- 22 -
&& AVX Offset (Note)
AVX offset is the negative offset of AVX ratio.
&& Uncore Ratio
Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.
&& Uncore Frequency
Displays the current CPU Uncore frequency.
&& CPU Flex Ratio Override
Enables or disables the CPU Flex Ratio. The maximum CPU clock ratio will be based on the CPU Flex
Ratio Settings value if CPU Clock Ratio is set to Auto. (Default: Disabled)
&& CPU Flex Ratio Settings
Allows you to set the CPU Flex Ratio. The adjustable range may vary by CPU.
&& Intel(R) Turbo Boost Technology (Note)
Allows you to determine whether to enable the Intel® CPU Turbo Boost technology. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& Turbo Ratio (Note)
Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios
according to the CPU specifications. (Default: Auto)
&& Power Limit TDP (Watts) / Power Limit Time
Allows you to set the power limit for CPU Turbo mode and how long it takes to operate at the specified
power limit. If the specified value is exceeded, the CPU will automatically reduce the core frequency in
order to reduce the power. Auto sets the power limit according to the CPU specifications. (Default: Auto)
&& Core Current Limit (Amps)
Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specified current
limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the
power limit according to the CPU specifications. (Default: Auto)
&& Turbo Per Core Limit Control (Note)
Allows you to control each CPU core limit separately. (Default: Auto)
&& No. of CPU Cores Enabled (Note)
Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU
cores may vary by CPU). Auto lets the BIOS automatically configure this setting. (Default: Auto)
&& Hyper-Threading Technology (Note)
Allows you to determine whether to enable multi-threading technology when using an Intel® CPU that
supports this function. This feature only works for operating systems that support multi-processor mode.
Auto lets the BIOS automatically configure this setting. (Default: Auto)
&& Intel(R) Speed Shift Technology (Intel® Speed Shift Technology) (Note)
Enables or disables Intel® Speed Shift Technology. Enabling this feature allows the processor to ramp up
its operating frequency more quickly and then improves the system responsiveness. (Default: Auto)
&& CPU Enhanced Halt (C1E) (Note)
Enables or disables Intel® CPU Enhanced Halt (C1E) function, a CPU power-saving function in system
halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to
decrease power consumption. Auto lets the BIOS automatically configure this setting. (Default: Auto)
- 23 -
&& C3 State Support (Note)
Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically configure
this setting. (Default: Auto)
&& C6/C7 State Support (Note)
Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the
The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically configure
Allows you to determine whether to let the CPU enter C8 mode in system halt state. When enabled, the CPU
core frequency and voltage will be reduced during system halt state to decrease power consumption. The
C8 state is a more enhanced power-saving state than C6/C7. Auto lets the BIOS automatically configure
Allows you to determine whether to let the CPU enter C10 mode in system halt state. When enabled, the
The C10 state is a more enhanced power-saving state than C8. Auto lets the BIOS automatically configure
&& Package C State Limit (Note)
Allows you to specify the C-state limit for the processor. Auto lets the BIOS automatically configure this
setting. (Default: Auto)
&& CPU Thermal Monitor (Note)
Enables or disables Intel® Thermal Monitor function, a CPU overheating protection function. When enabled,
the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS
&& Ring to Core offset (Down Bin)
Allows you to determine whether to disable the CPU Ring ratio auto-down function. Auto lets the BIOS
&& CPU EIST Function (Note)
Enables or disables Enhanced Intel® Speed Step Technology (EIST). Depending on CPU loading, Intel®
EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease
average power consumption and heat production. Auto lets the BIOS automatically configure this setting.
(Default: Auto)
&& Race To Halt (RTH) (Note)/Energy Efficient Turbo (Note)
Enables or disables the CPU power saving related settings.
&& Voltage Optimization
Allows you to determine whether to enable voltage optimization to reduce power consumption. (Default:
Auto)
&& Hardware Prefetcher
Allows you to determine whether to enable hardware prefetcher to prefetch data and instructions from the
memory into the cache. (Default: Auto)
- 24 -
&& Adjacent Cache Line Prefetch
Allows you to determine whether to enable the adjacent cache line prefetch mechanism that lets the
processor retrieve the requested cache line as well as the subsequent cache line. (Default: Auto)
&& Extreme Memory Profile (X.M.P.) (Note)

Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when
enabled.

Disabled Disables this function. (Default)

Profile1 Uses Profile 1 settings.

Profile2 (Note)
Uses Profile 2 settings.
&& System Memory Multiplier
Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD
data. (Default: Auto)
&& Memory Ref Clock
Allows you to manually adjust the memory reference clock. (Default: Auto)
&& Memory Odd Ratio (100/133 or 200/266)
Allows you to manually adjust the memory reference clock. (Default: Auto)
&& Memory Frequency (MHz)
The first memory frequency value is the normal operating frequency of the memory being used; the second
is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings.
`` Advanced Memory Settings

&& Extreme Memory Profile (X.M.P.) (Note), System Memory Multiplier, Memory Ref Clock,
Memory Odd Ratio (100/133 or 200/266), Memory Frequency(MHz)
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&& Memory Boot Mode (Note)
Provides memory detection and training methods.

Auto Lets the BIOS automatically configure this setting. (Default)

Normal The BIOS automatically performs memory training. Please note that if the system
becomes unstable or unbootable, try to clear the CMOS values and reset the board
to default values. (Refer to the introductions of the battery/clear CMOS jumper in
Chapter 1 for how to clear the CMOS values.)

Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory
boot.

Disable Fast Boot Detect and train memory at every single boot.
&& Realtime Memory Timing
Allows you to fine-tune memory timings after the BIOS stage. (Default: Auto)
&& Memory Enhancement Settings

Provides several memory performance enhancement settings: Normal (basic performance), Relax OC,
Enhanced Stability, and Enhanced Performance. (Default: Normal)
&& Memory Timing Mode
Manual and Advanced Manual allows the Memory Multiplier Tweaker, Channel Interleaving, Rank
Interleaving, and memory timing settings below to be configurable. Options are: Auto (default), Manual,
Advanced Manual.
(Note) This item is present only when you install a CPU and a memory module that support this feature.
- 25 -
&& Profile DDR Voltage
When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Disabled, the value
is displayed according to your memory specification. When Extreme Memory Profile (X.M.P.) is set to
Profile1 or Profile2, the value is displayed according to the SPD data on the XMP memory.
&& Memory Multiplier Tweaker
Provides different levels of memory auto-tuning. (Default: Auto)
&& Channel Interleaving
Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access
different channels of the memory to increase memory performance and stability. Auto lets the BIOS
&& Rank Interleaving
Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different
ranks of the memory to increase memory performance and stability. Auto lets the BIOS automatically
configure this setting. (Default: Auto)
`` Channel A/B Memory Sub Timings

This sub-menu provides memory timing settings for each channel of memory. The respective timing setting
screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual. Note: Your
system may become unstable or fail to boot after you make changes on the memory timings. If this occurs,
please reset the board to default values by loading optimized defaults or clearing the CMOS values.
`` Advanced Voltage Settings

`` Advanced Power Settings
This section provides Loadline voltage control options.
`` CPU Core Voltage Control
This section provides CPU voltage control options.
`` Chipset Voltage Control
This section provides Chipset voltage control options.
`` DRAM Voltage Control
This section provides memory voltage control options.
`` Internal VR Control
This section provides VR voltage control options.
`` PC Health Status
&& Reset Case Open Status

Disabled Keeps or clears the record of previous chassis intrusion status. (Default)

Enabled Clears the record of previous chassis intrusion status and the Case Open field will
show "No" at next boot.
&& Case Open
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI
header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To
clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to
the CMOS, and then restart your system.
&& CPU Vcore/CPU VCCSA/DRAM Channel A/B Voltage/+3.3V/+5V/+12V/CPU VAXG
Displays the current system voltages.
- 26 -
`` Miscellaneous Settings
&& Max Link Speed
Allows you to set the operation mode of the PCI Express slots to Gen 1, Gen 2, or Gen 3. Actual operation
mode is subject to the hardware specification of each slot. Auto lets the BIOS automatically configure this
setting. (Default: Auto)
&& 3DMark01 Enhancement
Allows you to determine whether to enhance some legacy benchmark performance. (Default: Disabled)
`` Smart Fan 5 Settings

&& Monitor
Allows you to select a target to monitor and to make further adjustment. (Default: CPU FAN)
&& Fan Speed Control
Allows you to determine whether to enable the fan speed control function and adjust the fan speed.

Normal Allows the fan to run at different speeds according to the temperature. You can adjust
the fan speed with System Information Viewer based on your system requirements.
(Default)

Silent Allows the fan to run at slow speeds.

Manual Allows you to control the fan speed in the curve graph.
Speed
Full Allows the fan to run at full speeds.
&& Fan Control Use Temperature Input
Allows you to select the reference temperature for fan speed control.
&& Temperature Interval
Allows you to select the temperature interval for fan speed change.
&& Fan Control Mode

Auto Lets the BIOS automatically detect the type of fan installed and sets the optimal control
mode. (Default)

Voltage Voltage mode is recommended for a 3-pin fan.

PWM PWM mode is recommended for a 4-pin fan.
&& Fan Stop
Enables or disables the fan stop function. You can set the temperature limit using the temperature curve.
The fan stops operation when the temperature is lower than the limit. (Default: Disabled)
&& Temperature
Displays the current temperature of the selected target area.
&& Fan Speed
Displays current fan speeds.
&& Temperature Warning Control
Sets the warning threshold for temperature. When temperature exceeds the threshold, BIOS will emit
warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF.
&& Fan Fail Warning
Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or fan
connection when this occurs. (Default: Disabled)
- 27 -
2-4 System
This section provides information on your motherboard model and BIOS version. You can also select the default
language used by the BIOS and manually set the system time.
&& Access Level

Displays the current access level depending on the type of password protection used. (If no password is
set, the default will display as Administrator.) The Administrator level allows you to make changes to all
BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all.
&& System Language
Selects the default language used by the BIOS.
&& System Date
Sets the system date. The date format is week (read-only), month, date, and year. Use <Enter> to switch
between the Month, Date, and Year fields and use the <Page Up> or <Page Down> key to set the desired
value.
&& System Time
Sets the system time. The time format is hour, minute, and second. For example, 1 p.m. is 13:00:00. Use
<Enter> to switch between the Hour, Minute, and Second fields and use the <Page Up> or <Page Down>
key to set the desired value.
- 28 -
2-5 BIOS
&& Bootup NumLock State

Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST. (Default: On)
&& Security Option
Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup.
After configuring this item, set the password(s) under the Administrator Password/User Password item.

Setup A password is only required for entering the BIOS Setup program.

System A password is required for booting the system and for entering the BIOS Setup
program. (Default)
&& Full Screen LOGO Show
Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the
GIGABYTE Logo when the system starts up. (Default: Enabled)
&& Boot Option Priorities
Specifies the overall boot order from the available devices. Removable storage devices that support GPT
format will be prefixed with "UEFI:" string on the boot device list. To boot from an operating system that
supports GPT partitioning, select the device prefixed with "UEFI:" string.
Or if you want to install an operating system that supports GPT partitioning such as Windows 10 64-bit,
select the optical drive that contains the Windows 10 64-bit installation disk and is prefixed with "UEFI:"
string.
&& Hard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities
Specifies the boot order for a specific device type, such as hard drives, optical drives, floppy disk drives,
and devices that support Boot from LAN function, etc. Press <Enter> on this item to enter the submenu that
presents the devices of the same type that are connected. This item is present only if at least one device
for this type is installed.
&& Fast Boot

Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup
- 29 -
speed. (Default: Disabled)
&& SATA Support

Last Boot HDD Only Except for the previous boot drive, all SATA devices are disabled before the OS
boot process completes. (Default)
Sata Devices All SATA devices are functional in the operating system and during the POST.
All
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
&& VGA Support
Allows you to select which type of operating system to boot.

Auto Enables legacy option ROM only.
Driver
EFI Enables EFI option ROM. (Default)
&& USB Support

Disabled All USB devices are disabled before the OS boot process completes.
Initial
Full All USB devices are functional in the operating system and during the POST.

Partial Initial Part of the USB devices are disabled before the OS boot process completes.
(Default)
This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot
is set to Ultra Fast.
&& PS2 Devices Support

Disabled All PS/2 devices are disabled before the OS boot process completes.

Enabled All PS/2 devices are functional in the operating system and during the POST.
(Default)
This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot
is set to Ultra Fast.
&& NetWork Stack Driver Support

Disabled Disables booting from the network. (Default)

Enabled Enables booting from the network.
&& Next Boot After AC Power Loss

Normal Boot Enables normal bootup upon the return of the AC power. (Default)

Fast Boot Keeps the Fast Boot settings upon the return of the AC power.
&& Mouse Speed

Allows you to set the mouse cursor movement speed. (Default: 1 X)
&& CSM Support

Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process.

Disabled Disables UEFI CSM and supports UEFI BIOS boot process only.

Enabled Enables UEFI CSM. (Default)
&& LAN PXE Boot Option ROM
Allows you to select whether to enable the legacy option ROM for the LAN controller. (Default: Disabled)
This item is configurable only when CSM Support is set to Enabled.
&& Storage Boot Option Control
Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller.
Do not launch Disables option ROM.

Legacy Enables legacy option ROM only.

UEFI Enables UEFI option ROM only. (Default)
- 30 -
&& Other PCI Device
Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other
than the LAN, storage device, and graphics controllers.
Do not launch Disables option ROM.

Legacy Enables legacy option ROM only.

UEFI Enables UEFI option ROM only. (Default)
&& Administrator Password

Allows you to configure an administrator password. Press <Enter> on this item, type the password, and
then press <Enter>. You will be requested to confirm the password. Type the password again and press
<Enter>. You must enter the administrator password (or user password) at system startup and when entering
BIOS Setup. Differing from the user password, the administrator password allows you to make changes to
all BIOS settings.
&& User Password
Allows you to configure a user password. Press <Enter> on this item, type the password, and then press
<Enter>. You will be requested to confirm the password. Type the password again and press <Enter>.
You must enter the administrator password (or user password) at system startup and when entering BIOS
Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.
To cancel the password, press <Enter> on the password item and when requested for the password, enter
the correct one first. When prompted for a new password, press <Enter> without entering any password.
Press <Enter> again when prompted to confirm.
NOTE: Before setting the User Password, be sure to set the Administrator Password first.
- 31 -
2-6 Peripherals
&& Initial Display Output

Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard
graphics.

IGFX Sets the onboard graphics as the first display.

PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the first display. (Default)

PCIe 2 Slot Sets the graphics card on the PCIEX4 slot as the first display.
&& OnBoard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
&& Above 4G Decoding
Enables or disables 64-bit capable devices to be decoded in above 4 GB address space (only if your system
supports 64-bit PCI decoding). Set to Enabled if more than one advanced graphics card are installed and
their drivers are not able to be launched when entering the operating system (because of the limited 4 GB
memory address space). (Default: Disabled)
&& RGB Fusion (Onboard LED)
Allows you to set the LED lighting mode for the motherboard.

On Enables this function. (Default)

Off Disables this function.
&& RGB Fusion (LED strip)
Allows you to set the display color of the external LED strip.
&& Intel Platform Trust Technology (PTT)
Enables or disables Intel® PTT Technology. (Default: Disabled)
&& Software Guard Extensions (SGX)
Enables or disables the Intel® Software Guard Extensions technology. This feature allows legal software
to operate in a safe environment and protects the software against attacks from malicious software. The
Software Controlled option allows you to enable or disable this feature with an Intel-provided application.
(Default: Software Controlled)
- 32 -
`` OffBoard SATA Controller Configuration
Displays information on your M.2 PCIe SSD if installed.
`` Trusted Computing
Enables or disables Trusted Platform Module (TPM).
`` Super IO Configuration
&& Serial Port
Enables or disables the onboard serial port. (Default: Enabled)
&& Parallel Port
Enables or disables the onboard parallel port. (Default: Enabled)
`` Intel(R) Bios Guard Technology

Enables or disables the Intel® BIOS Guard feature, which protects the BIOS from malicious attacks.
`` USB Configuration
&& Legacy USB Support
Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)
&& XHCI Hand-off
Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off
support. (Default: Disabled)
&& USB Mass Storage Driver Support
Enables or disables support for USB storage devices. (Default: Enabled)
&& Port 60/64 Emulation
Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support
for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices.
(Default: Enabled)
&& Mass Storage Devices
Displays a list of connected USB mass storage devices. This item appears only when a USB storage device
is installed.
`` Network Stack Configuration

&& Network Stack
Disables or enables booting from the network to install a GPT format OS, such as installing the OS from
the Windows Deployment Services server. (Default: Disabled)
&& Ipv4 PXE Support
Enables or disables IPv4 PXE Support. This item is configurable only when Network Stack is enabled.
&& Ipv4 HTTP Support
Enables or disables HTTP boot support for IPv4. This item is configurable only when Network Stack is
enabled.
&& Ipv6 PXE Support
Enables or disables IPv6 PXE Support. This item is configurable only when Network Stack is enabled.
&& Ipv6 HTTP Support
Enables or disables HTTP boot support for IPv6. This item is configurable only when Network Stack is
enabled.
&& PXE boot wait time
Allows you to configure how long to wait before you can press <Esc> to abort the PXE boot. This item is
configurable only when Network Stack is enabled. (Default: 0)
- 33 -
&& Media detect count
Allows you to set the number of times to check the presence of media. This item is configurable only when
Network Stack is enabled. (Default: 1)
`` NVMe Configuration
Displays information on your M.2 NVME PCIe SSD if installed.
`` SATA And RST Configuration

&& SATA Controller(s)
Enables or disables the integrated SATA controllers. (Default: Enabled)
&& SATA Mode Selection
Specifies the operating mode of the integrated SATA controllers.

Intel RST With Intel Optane System Acceleration Enables Intel® Optane™ Technology support for
the SATA controllers.

AHCI Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specification that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug. (Default)
&& Aggressive LPM Support
Enables or disables the power saving feature, ALPM (Aggressive Link Power Management), for the Chipset
SATA controllers. (Default: Enabled)
&& Port 0/1/2/3/4/5
Enables or disables each SATA port. (Default: Enabled)
&& Hot plug
Enables or disable the hot plug capability for each SATA port. (Default: Disabled)
&& Configured as eSATA
Enables or disables support for external SATA devices.
`` Realtek PCIe GBE Family Controller

This sub-menu provides information on LAN configuration and related configuration options.
- 34 -
2-7 Chipset
&& VT-d (Note)

Enables or disables Intel® Virtualization Technology for Directed I/O. (Default: Enabled)
&& Internal Graphics
Enables or disables the onboard graphics function. (Default: Auto)
&& DVMT Pre-Allocated
Allows you to set the onboard graphics memory size. Options are: 32M~1024M. (Default: 64M)
&& DVMT Total Gfx Mem
Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX.
(Default: 256M)
&& Audio Controller
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
&& High Precision Timer

Enables or disables High Precision Event Timer (HPET) in the operating system. (Default: Enabled)
&& IOAPIC 24-119 Entries
Enables or disables this function. (Default: Enabled)
- 35 -
2-8 Power
&& Platform Power Management

Enables or disables the Active State Power Management function (ASPM). (Default: Enabled)
&& PEG ASPM
Allows you to configure the ASPM mode for the device connected to the CPU PEG bus. This item is
configurable only when Platform Power Management is set to Enabled. (Default: Disabled)
&& PCH ASPM
Allows you to configure the ASPM mode for the device connected to Chipset's PCI Express bus. This item
is configurable only when Platform Power Management is set to Enabled. (Default: Disabled)
&& DMI ASPM
Allows you to configure the ASPM mode for both CPU side and Chipset side of the DMI link. This item is
configurable only when Platform Power Management is set to Enabled. (Default: Enabled)
&& AC BACK
Determines the state of the system after the return of power from an AC power loss.

Memory The system returns to its last known awake state upon the return of the AC power.

Always On The system is turned on upon the return of the AC power.

Always Off The system stays off upon the return of the AC power. (Default)
&& Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.


Password Set a password with 1~5 characters to turn on the system.

Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
Key
Any Press any key to turn on the system.
- 36 -
&& Power On Password
Set the password when Power On By Keyboard is set to Password.
Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept.
To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter>
again without entering the password to clear the password settings.
&& Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.


Move Move the mouse to turn on the system.

Double Click Double click on left button on the mouse to turn on the system.
&& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,
power on by mouse, and power on by keyboard.
&& Soft-Off by PWR-BTTN
Configures the way to turn off the computer in MS-DOS mode using the power button.

Instant-Off Press the power button and then the system will be turned off instantly. (Default)

Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power button
is pressed for less than 4 seconds, the system will enter suspend mode.
&& Resume by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:

Wake up day: Turn on the system at a specific time on each day or on a specific day in a month.

Wake up hour/minute/second: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
&& CEC 2019 Ready
Allows you to select whether to allow the system to adjust power consumption when it is in shutdown, idle,
or standby state in order to comply with the CEC (California Energy Commission) 2019 Standards. (Default:
Disabled)
&& RC6(Render Standby)
Allows you to determine whether to let the onboard graphics enter standby mode to decrease power
consumption. (Default: Enabled)
- 37 -
2-9 Save & Exit
&& Save & Exit Setup

Press <Enter> on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup
program. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Exit Without Saving
Press <Enter> on this item and select Yes. This exits the BIOS Setup without saving the changes made
in BIOS Setup to the CMOS. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Load Optimized Defaults
Press <Enter> on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults
settings help the system to operate in optimum state. Always load the Optimized defaults after updating
the BIOS or after clearing the CMOS values.
&& Boot Override
Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yes
to confirm. Your system will restart automatically and boot from that device.
&& Save Profiles
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and
save as Setup Profile 1~ Setup Profile 8. Press <Enter> to complete. Or you can select Select File in
HDD/FDD/USB to save the profile to your storage device.
&& Load Profiles
If your system becomes unstable and you have loaded the BIOS default settings, you can use this function
to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS
settings. First select the profile you wish to load and then press <Enter> to complete. You can select Select
File in HDD/FDD/USB to input the profile previously created from your storage device or load the profile
automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked
properly (last known good record).
- 38 -
Chapter 3 Appendix
3-1 Installing an Intel® Optane™ Memory
System Requirements
1. Intel® Optane™ SSD
2. The Optane™ memory must have at least 16 GB capacity, and it must have equal or smaller capacity than
the hard drive/SSD to be accelerated.
3. The hard drive/SSD to be accelerated must be a SATA hard drive or M.2 SATA SSD and must have Windows
10 64-bit (or later version) installed on it. (Must be formatted for GPT partition.)
4. The motherboard driver disk
Installation Guidelines
A-1: Installation in AHCI mode
If the SATA controller has been configured in AHCI mode, please follow the steps below:
1. After entering the operating system, insert the motherboard driver disk into your optical drive. On the Xpress
Install screen, select Intel(R) Optane(TM) Memory System Acceleration (Note) to install. Follow the on-screen
instructions to continue. The system will auto-restart.
2. After re-entering the operating system, the dialog box as shown above will appear. Click Yes to continue the
installation and then restart the system.
3. Launch the Intel(R) Optane Memory application from the Start menu. A message which says Intel® Optane™
Memory is disabled will appear on the main screen. Click Enable to activate the Intel® Optane™ Memory
and restart the system again.
4. Launch the Intel(R) Optane Memory application from the Start menu and make sure the Intel® Optane™
Memory has been enabled. (The SATA controller mode is changed to Intel RST With Intel Optane System
Acceleration from AHCI mode. DO NOT change your SATA controller mode back to AHCI. Doing so will
prevent Intel® Optane™ memory from functioning properly.)
A-2: Installation in Intel RST With Intel Optane System Acceleration mode
If the SATA controller has been configured in Intel RST With Intel Optane System Acceleration mode, please
follow the steps below:
1. After system restarts, go to the BIOS Setup, make sure CSM Support under the BIOS menu is disabled.
2. Go to Peripherals\SATA And RST Configuration and make sure Use RST Legacy OROM is disabled. If
you want to enable the Optane™ memory installed in the M2M_32G connector, set PCIe Storage Dev on
Port 21 to RST Controlled.
3. Enter the operating system, launch the Intel® Rapid Storage Technology utility from the Start menu, and then
enable Intel® Optane™ Memory on the Intel® Optane™ Memory screen.
4. Follow the on-screen instruction to continue the installation and then restart the system when completed.
•• An Optane™ memory cannot be used to accelerate an M.2 PCIe SSD.

•• Do not abruptly remove the Optane™ memory. Doing so will cause the operating system to stop
functioning correctly.
•• If you want to change/remove the Optane™ memory, you must disable it using the Intel® Rapid
Storage Technology or Intel(R) Optane™ Memory application first.
•• After enabling the Optane™ memory, the related BIOS settings will remain even after a BIOS update.
(Note) If the system already has Intel® Rapid Storage Technology utility installed, you have to remove it first
before installing the Intel(R) Optane(TM) Memory System Acceleration application.
- 39 -
3-2 Drivers Installation
•• Before installing the drivers, first install the operating system.
•• After installing the operating system, insert the motherboard driver disk into your optical drive. Click
on the message "Tap to choose what happens with this disc" on the top-right corner of the screen
and select "Run Run.exe." (Or go to My Computer, double-click the optical drive and execute the
Run.exe program.)
"Xpress Install" will automatically scan your system and then list all of the drivers that are recommended to
install. You can click the Xpress Install button and "Xpress Install" will install all of the selected drivers. Or click
the arrow icon to individually install the drivers you need.
Please visit GIGABYTE's website for Please visit GIGABYTE's website for
more software information. more troubleshooting information.
- 40 -
Regulatory Statements
Regulatory Notices
This document must not be copied without our written permission, and the contents there of must not be imparted
to a third party nor be used for any unauthorized purpose.
Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects
at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text.
Also note that the information in this document is subject to change without notice and should not be construed
as a commitment by GIGABYTE.
Our Commitment to Preserving the Environment

In addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations
for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE
(Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety
requirements. To prevent releases of harmful substances into the environment and to maximize the use of our
natural resources, GIGABYTE provides the following information on how you can responsibly recycle or reuse
most of the materials in your "end of life" product.
Restriction of Hazardous Substances (RoHS) Directive Statement

GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE
and PBB). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at
GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.
Waste Electrical & Electronic Equipment (WEEE) Directive Statement

GIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and Electronic
Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric
and electronic devices and their components. Under the Directive, used equipment must be marked, collected
separately, and disposed of properly.
WEEE Symbol Statement

The symbol shown below is on the product or on its packaging, which indicates that this product
must not be disposed of with other waste. Instead, the device should be taken to the waste collection
centers for activation of the treatment, collection, recycling and disposal procedure. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for recycling, please contact your
local government office, your household waste disposal service or where you purchased the product for details
of environmentally safe recycling.
When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or regional
waste collection administration for recycling.
If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the
Customer Care number listed in your product's user's manual and we will be glad to help you with your effort.
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the
energy-saving features of this product (where applicable), recycling the inner and outer packaging (including
shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly.
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic
equipment, minimize the use of landfills for the disposal of "end of life" products, and generally improve our
quality of life by ensuring that potentially hazardous substances are not released into the environment and are
disposed of properly.
- 41 -
FCC Notice (U.S.A. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult a dealer or experienced TV/radio technician for help.
Canada, Industry Canada (IC) Notices / Canada, avis d'Industry Canada (IC)
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer
d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent
affecter son fonctionnement.
- 42 -
Contact Us
GIGA-BYTE TECHNOLOGY CO., LTD.

Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231, Taiwan
TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : http://esupport.gigabyte.com
WEB address (English): http://www.gigabyte.com
WEB address (Chinese): http://www.gigabyte.tw
•• GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to:
http://esupport.gigabyte.com
- 43 -

B360M DS3H Motherboard Manual

Uploaded by

Copyright:

Available Formats

B360M DS3H Motherboard Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

B360M DS3H Motherboard Manual

Uploaded by

Copyright:

Available Formats

B360M DS3H

For more product details, please visit GIGABYTE's website.

B360M DS3H Motherboard Layout..................................................................................4

Chapter 1 Hardware Installation......................................................................................5

Chapter 2 BIOS Setup...................................................................................................20

Realtek® B360M DS3H

COM F_USB2 F_PANEL

1-4 Installing the Memory

Please visit GIGABYTE's website for details on hardware installation.

1-5 Installing an Expansion Card

1-6 Back Panel Connectors

USB 2.0/1.1 Port

Line In/Rear Speaker Out (Blue)

Audio Jack Configurations:

1) ATX_12V_2X4 10) SPDIF_O

Read the following guidelines before connecting external devices:

SATA3 1 To enable hot-plugging for the SATA ports, refer to Chapter

7) M2M_32G (M.2 Socket 3 Connector)

Installation Notices for the M.2 and SATA Connectors:

M.2 SATA SSD a a a a a r

M.2 PCIe SSD a a a a a a

No M.2 SSD Installed a a a a a a

a: Available, r: Not available

on the chassis front panel. The LED is on

to Chapter 2, "BIOS Setup," "Power," for more information).

•• RES (Reset Switch):

if the computer freezes and fails to perform a normal restart.

front panel module to this header, make

9) F_AUDIO (Front Panel Audio Header)

12) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

9 1 Pin No. Definition Pin No. Definition

13) COM (Serial Port Header)

Pin No. Definition Pin No. Definition

14) LPT (Parallel Port Header)

15) TPM (Trusted Platform Module Header)

You may clear the CMOS values by removing the battery:

17) CLR_CMOS (Clear CMOS Jumper)

Short: Clear CMOS Values

2-1 Startup Screen

Classic Setup Function Keys

`` Advanced Frequency Settings

&& CPU Clock Ratio

`` Advanced CPU Core Settings

&& Extreme Memory Profile (X.M.P.) (Note)

`` Advanced Memory Settings

&& Memory Enhancement Settings

`` Channel A/B Memory Sub Timings

`` Advanced Voltage Settings

`` Smart Fan 5 Settings

&& Access Level

&& Bootup NumLock State

&& Fast Boot

&& Mouse Speed

&& CSM Support

&& Administrator Password

&& Initial Display Output

`` Intel(R) Bios Guard Technology

`` Network Stack Configuration

`` SATA And RST Configuration