Clutch Adjustment Toyota Corolla (E15) 2007-2010

4/24/2019 Adjustment instructions clutch sensor on Toyota Corolla MMT
WebBlack.net
Autoworld reviews
and tests
Adjustment instructions clutch sensor on Toyota Corolla

MMT
Запчасти для Toyo… Запчасти для T… Запчасти для Toyo… Запчасти для Toyo… Запчасти для T… Запчасти для Ho…
Цена на са… Цена на … Цена на сай… Цена на са… Цена на … Цена на …
О компании
«Adjusting the clutch without the use of portable diagnostic instrument».
1. Prepare auto (switch gear lever to position «N», turn o the ignition, put on the handbrake.)
2. Perimysium contacts in the diagnostic connector DLC3 .

No. 4 (he is fourth from left in top row) and No. 13 (he is fth from the left in the bottom row).
http://webblack.net/adjustment-instructions-clutch-sensor-on-toyota-corolla-mmt/ 1/5
Wait at least 10 seconds.
3. Turn on the ignition when the brake pedal is released (not start).
4. For 3 seconds you should press on the brake pedal at least 7 times.
5. Further, the buzzer will emit 2 long beeps with an interval of 0.25 sec.
6. Push the brake pedal.
7. Hold down the brake, move the shift lever in the following sequence:
N – E – M – plus M – plus M – plus M – plus – M – E – N
(4 times to turn the lever «plus». Thus between inclusions, «plus» do not need to return back to «E» and
«Neutral». In the «E» and «Natal» translate only after the last 4th turning «plus»).
8. Release the brake pedal.
9. Press the brake pedal again.
10. The buzzer will emit a series of beeps at intervals of 0.5 sec.
(If the interval between the signals is 1 second. or signals will not, then should I turn o the ignition, wait 15
seconds. pull the jumper and return to p. A.).
11. Press on the brake at least 3 times within 2 seconds.
12. The buzzer will emit a 2 signal with an interval of 0.25 sec.
12. Press on the brake again and hold the brake pedal down, switch the gear lever to position «Minus»
13. To release the brake.
14. Turn the ignition switch o and wait at least 10 seconds.
15. Disconnect the contacts DLC3 diagnostic connector
«Initialization (clutch linkage and travel sensor clutch) without the use of portable diagnostic
instrument».
Geekcreit 4A To 6A 24V Banggood Motorcycle

Switching... Helmet Lens...
8,52 AUD 12,35 USD
12,58 AUD 15,99 USD
Banggood.com
A. Prepare auto (switch gear lever to position «N», turn o the ignition)
B. Perimysium contacts in the diagnostic connector DLC3

No. 4 (he is fourth from left in top row) and No. 13 (he is fth from the left in the bottom row).
V. Wait at least 10 seconds. (this is also the di erence from the previous scheme).
G. Turn the ignition on (not start).
D. for 3 seconds you should press on the brake pedal 7 times.
E. the Buzzer will emit 2 long beeps with an interval of 0.25 sec.
J. Press on the brake pedal and hold…
C While pressing the brake, move the gear lever in the following sequence:
N – E – M – plus – minus – plus – minus – M – E – N
(from «neutral» to «plus – minus – plus – minus, and then again in «neutral»)
I. Let go of the brake
K. Press the brake again
L. the Buzzer will make 3 cycles of the signals 2 signals in a cycle at intervals of 0.5 sec. (simply put, sounds 6-th
signals, rst 2, then after a short pause, another 2, and then the last 2).
(If no signal or signals are published with an interval of 1sec. (up from 0.5 seconds), then turn the ignition o ,
wait at least 10 seconds. o .the ignition and return to the p. A.)
M. In 2 sec. click 3 times on the brake.
N. The buzzer will emit 2 beeps with an interval of 0.25 sec.
O turn the ignition switch O and wait at least 10 seconds.
P. Initialization is completed.
R. Disconnect the bridged contacts in DLC3.
«Setting without the use of a portable diagnostic device»
Jumper the contacts no longer required.
A. Prepare auto (switch gear lever to position «N», turn o the ignition.)
B. Turn the ignition on
V. to Wait at least 40 seconds.
Xiaomi Redmi Note 6 Pro CNC DC Stabilized Power

6.26 inch... Supply Module...
209,99 USD Flash Sale
31,88 USD
GearBest
G. turn O the ignition
D. Wait at least 15 seconds.
E. Turn the ignition on
J. Start the engine, providing the following conditions:

— the position of the gear lever is «N»
— The brake pedal is depressed
NOTE: At engine start ashes the indicator «N» gear (on the display). The engine does not turn o until until the
indicator «N» will stop blinking.
As soon as the indicator «N» began to burn continuously (stopped ashing) setup completed
Запис було зроблено в рубриці Auto - 02.02.2017 - dj-s.

Схожі по темі записи:
Why tight the brake pedal for VAZ 2110 Banggood Motorcycle
Helmet Lens...
How to synchronize the key for Peugeot
12,35 USD 15,99 USD
Pumping the brakes

Geekcreit 4A a 6A 24V
How to adjust the Parking brake for Chery Amulet Scheda...
6,18 CHF 9,13 CHF
Banggood Dual USB

5V 1A 2.1A Banco...
2,04 EUR 3,83 EUR
Banggood.com

Clutch Adjustment Toyota Corolla (E15) 2007-2010

Uploaded by

Copyright:

Available Formats

Clutch Adjustment Toyota Corolla (E15) 2007-2010

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Clutch Adjustment Toyota Corolla (E15) 2007-2010

Uploaded by

Copyright:

Available Formats

4/24/2019 Adjustment instructions clutch sensor on Toyota Corolla MMT

Adjustment instructions clutch sensor on Toyota Corolla

«Adjusting the clutch without the use of portable diagnostic instrument».

2. Perimysium contacts in the diagnostic connector DLC3 .

Wait at least 10 seconds.

6. Push the brake pedal.

N – E – M – plus M – plus M – plus M – plus – M – E – N

8. Release the brake pedal.

9. Press the brake pedal again.

11. Press on the brake at least 3 times within 2 seconds.

13. To release the brake.

14. Turn the ignition switch o and wait at least 10 seconds.

15. Disconnect the contacts DLC3 diagnostic connector

Geekcreit 4A To 6A 24V Banggood Motorcycle

B. Perimysium contacts in the diagnostic connector DLC3

G. Turn the ignition on (not start).

D. for 3 seconds you should press on the brake pedal 7 times.

J. Press on the brake pedal and hold…

N – E – M – plus – minus – plus – minus – M – E – N

I. Let go of the brake

K. Press the brake again

M. In 2 sec. click 3 times on the brake.

N. The buzzer will emit 2 beeps with an interval of 0.25 sec.

O turn the ignition switch O and wait at least 10 seconds.

R. Disconnect the bridged contacts in DLC3.

«Setting without the use of a portable diagnostic device»

Jumper the contacts no longer required.

B. Turn the ignition on

V. to Wait at least 40 seconds.

Xiaomi Redmi Note 6 Pro CNC DC Stabilized Power

G. turn O the ignition

D. Wait at least 15 seconds.

E. Turn the ignition on

J. Start the engine, providing the following conditions:

Запис було зроблено в рубриці Auto - 02.02.2017 - dj-s.

Pumping the brakes

Banggood Dual USB

You might also like