Technical Bulletin 517

Instruction Sheet Technical Bulletin 517 – Total Alkalinity
Measurement in Natural Waters

Background Information Alkalinity measurement is important in the control of water and wastewater treatment. In
a sample, alkalinity is defined as the quantitative ability to react with (neutralize) a known
quantity of standard acid. Many commonly occurring materials, such as carbonate, bicarbonate,
phosphates, and hydroxides, increase alkalinity in natural waters.
Conventional Ways to Alkalinity is measured commonly by titration, using either a burette or the drop count technique.
Measure Alkalinity A sample is titrated with an acid solution, which neutralizes the alkaline species present. The
endpoint is determined by observing a color change or by titrating to a pH value of 4.5, using
a pH electrode as an indicator. The volume of titrant required to change the color to reach the
endpoint is then used to calculate total alkalinity. Both methods have limitations. Sample color
or turbidity affects the operator’s ability to detect the color change. Use of a burette or dropper is
tedious and time-consuming.
Fast and Easy Alternative to The Thermo Scientific Orion total alkalinity test kit simplifies routine alkalinity measurement.
Measure Alkalinity Save time by eliminating additional equipment setup, tedious titrations and calculations. The
total alkalinity test kit is ideal for field use. Results are unaffected by sample color or turbidity,
and the kit does not require tedious drop counting.
• Direct readings of 0 to 225 ppm as CaCO3
• No titration needed
• No special equipment needed
• No interferences from color or turbidity
• Ideal for field determination

How The Total Alkalinity Test The principle of operation for the total alkalinity test kit is the same as the conventional titration.
Kit Works A reagent composed of several acids reacts with the alkaline species in the sample. As a result,
the pH of the sample changes. The observed pH reading after the addition of the reagent varies
directly with the total alkalinity, see Figure 1. Each pH reading corresponds to a unique value for
alkalinity, expressed in ppm as CaCO3.
Using your own pH electrode and pH meter, measure total alkalinity directly. Just calibrate for
pH as usual, add the total alkalinity reagent and read total alkalinity in ppm as CaCO3 from the
conversion wheel included in the kit.
OBSERVED pH
4.50
4.45
4.40
4.35
4.30
4.25
4.20
70 80 90 100 110
ppm CaCO3
Figure 1 – Total Alkalinity Test Kit Observed pH vs. ppm CaCO3
Total Alkalinity Test Kit Find the expected sample concentration range using Chart 1 and use the indicated volumes
Instructions of sample and total alkalinity reagent. If pH must be reported, measure and record the pH of
the sample prior to reagent addition. Follow the instructions below for measurement of total
alkalinity.
1. Calibrate the pH electrode and meter using pH 7 and pH 4 buffers, according to the meter
user guide.
2. Use a pipette or graduated cylinder to measure 100 mL of sample into beaker.
3. Pipette the appropriate amount of total alkalinity reagent into the sample and mix the
solution well. See Chart 1.
4. Measure the resulting pH of the sample.
5. Using the indicated side of the total alkalinity conversion wheel, find the resulting pH value
and read total alkalinity of sample in ppm as CaCO3.
Chart 1
Expected Sample Standard Volume Reagent Volume Expected Value

Concentration
0 to 25 ppm 1 mL 1 mL 4.64 ± 0.05
0 to 225 ppm 10 mL 10 mL 4.41 ± 0.05
Measure the total alkalinity standard/control every 10 samples or daily as a verification of

measurement. See the Use of Total Alkalinity Standard/Control section.
Technical Bulletin 517

Use of Total Alkalinity Use the total alkalinity standard/control daily, or after every ten samples, for verification of proper
Standard/Control measurement.
Chart 2
Range Sample Volume Reagent Volume Wheel Side Accuracy

Low level 100 mL 1 mL Blue ± 0.5 ppm
0 to 25 ppm
Full 100 mL 10 mL Gray ± 5 ppm
0 to 225 ppm
Greater than 10 mL diluted 10 mL Gray (multiply ± 5 ppm
225 ppm to 100 mL with results by 10)
distilled water
1. Carefully pipette the appropriate volume of 1,000 ppm standard/control into a clean 100 mL
volumetric flask and dilute to the mark with deionized water. Mix the solution well.
2. Transfer the solution to a clean beaker and add the appropriate volume of total alkalinity
reagent. Mix the solution well.
3. Calibrate the pH electrode and meter using pH 7 and pH 4 buffers, according to the meter
user guide.
4. Measure the pH of the control. See Chart 2 for expected values.
If the pH value of the control is not within the range:
1. Recalibrate the pH electrode and meter using fresh buffers. The electrode slope should be
92% to 102%.
2. Prepare a fresh control.
3. Check the alkalinity of the deionized water. Any alkalinity in the water used for diluting the
standard will contribute to the total alkalinity measured in the control:
a. Measure the total alkalinity of the deionized water, using the low level procedure, and
multiply the result by 0.9. This value, AH2O, is the contribution to the total alkalinity
from the deionized water.
b. Carefully pipette 10 mL of 1,000 ppm standard/control into a clean 100 mL volumetric

flask, dilute to mark with deionized water, and mix the solution well.
c. Transfer the solution to a clean beaker, add 10 mL of total alkalinity reagent, and mix
the solution well.
d. Measure the pH of the solution and use the gray side of the conversion wheel to read the
total alkalinity, A.
e. Determine the alkalinity of the control, Ac, using the following formula:
Ac = A - AH2O
The value should be 100 ± 5 ppm.
Technical Bulletin 517

Ordering Information Cat. No. Description
700010 Total alkalinity test kit, includes total alkalinity reagent, 1 x 475 mL
bottle; alkalinity standard/control, 1 x 475 mL bottle; and total alkalinity
conversion wheel. Average of 80 tests per kit.
700011 Total alkalinity reagent, 4 x 475 mL bottles
700012 Alkalinity standard/control, 1 x 475 mL bottle
Environmental Instruments Toll Free: 1-800-225-1480

Water Analysis Instruments Tel: 1-978-232-6000
Dom. Fax: 1-978-232-6015
166 Cummings Center Int’l Fax: 978-232-6031
Beverly, MA 01915 USA email: [email protected]
www.thermo.com/water
© 2008 Thermo Fisher Scientific Inc.
255004-001 Rev.A 03-08 All rights reserved.

Technical Bulletin 517 - Total Alkalinity Measurement in Natural Waters

Uploaded by

Copyright:

Available Formats

Technical Bulletin 517 - Total Alkalinity Measurement in Natural Waters

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Technical Bulletin 517 - Total Alkalinity Measurement in Natural Waters

Uploaded by

Copyright:

Available Formats

Instruction Sheet Technical Bulletin 517 – Total Alkalinity

Measurement in Natural Waters

• Direct readings of 0 to 225 ppm as CaCO3

• No special equipment needed

• No interferences from color or turbidity

• Ideal for field determination

Figure 1 – Total Alkalinity Test Kit Observed pH vs. ppm CaCO3

2. Use a pipette or graduated cylinder to measure 100 mL of sample into beaker.

4. Measure the resulting pH of the sample.

Expected Sample Standard Volume Reagent Volume Expected Value

Measure the total alkalinity standard/control every 10 samples or daily as a verification of

Technical Bulletin 517 

Range Sample Volume Reagent Volume Wheel Side Accuracy

4. Measure the pH of the control. See Chart 2 for expected values.

If the pH value of the control is not within the range:

2. Prepare a fresh control.

b. Carefully pipette 10 mL of 1,000 ppm standard/control into a clean 100 mL volumetric

The value should be 100 ± 5 ppm.

Technical Bulletin 517 

Environmental Instruments Toll Free: 1-800-225-1480

You might also like

b. Carefully pipette 10 mL of 1,000 ppm standard/control into a clean 100 mL volumetric

Technical Bulletin 517