Installation Manual

SAS3
INSTALLATION MANUAL
SNONO SYSTEMS ©
2015
SAS3 Billing System VERSION 3.x
________________________________________________________________________
FORWARD
This document describes the installation procedure of SAS3 billing system on x86-64 bit host
or virtual machine.
The manual covers the installation and configuration of the NAS (Mikrotik & Cisco) using
PPPoE and hotspot setup.
Please note that SAS3 receives online updates from time to time , it is always recommended
to update your software to the latest version before starting the configuration section.
1
________________________________________________________________________
INSTALLATION
Requirements
Minimum hardware requirements :

- Intel Core i3 or better (64bit CPU is mandetory)
- 4GB of RAM
- 250GB HDD or more (7200 RPM or better)
Software Requirement :
- SAS3 ISO image which can be downloaded from w ww.snono-systems.com
- CD Burning software such as Nero on windows or K3B on Linux.
Starting Up
Boot the server using SAS3 ISO image and select “Install SAS3”
2
________________________________________________________________________
SAS3 installation is fully automated. If you install on blank hard drive , no questions will be
asked. Sometimes when the target disk has some partitions left on , SAS3 will come up with
the following screen. Select 'Yes' to continue
3
________________________________________________________________________
When installation is over,the server will reboot twice. When done , Linux login prompt will
appear.Login using username (sas) and password (sas123).
4
________________________________________________________________________
Set your IP address, netmask ,gateway & DNS server (very important).Also make sure you
set your correct timezone
5
________________________________________________________________________
Next , the server must be connected to the network and internet is reachable. Internet is
required to activate the server with the demo license.
From your web browser ,login to http://your_ip_address using username & password :
admin/admin
6
________________________________________________________________________
In the dashboard , make sure that snono-systems.com is reachable. SAS3 will try to fetch
the license from our license server. If it fails to reach our license server, SAS3 will become
inactive and will work with limit functionality.
7
________________________________________________________________________
NAS Configuration
Mikrotik
Figure-1
simple NAS setup with RADIUS server.
In this example , we will assume that you have the following configuration :
- Mikrotik RouterOS NAS : 192.168.240.2

- SAS3 RADIUS : 192.168.240.10
- Switch/Hub connecting your WAN,SAS3,NAS all together.
- Users connected to the NAS via PPPoE and/or Hotspot.
To send authentication and accounting requests to Radius server, You have to

configure your Mikrotik NAS. Use Winbox to view and edit the configuration. Follow
these steps:
1. Connect to your Mikrotik router using Winbox.

2. Select Radius from the main menu.
3. Click + to define a new RADIUS authentication server:
4. In the ‘Address’ field , add your SAS3 RADIUS IP address.
5. Set the ‘Secret’ to anything you like , remember it as you will need this later.
6. Timeout is preferred to be 3000 ms or higher.
8
________________________________________________________________________
Figure-2
Mikrotik RADIUS client configuration
Set RADIUS incoming port to 1700 from RADIUS->Incoming
Figure-3
9
________________________________________________________________________
PPPoE setup
Create new PPPoE service from PPP->PPPoE Servers and click on add (+)
Figure-4
Make sure that mschap1 & m

schap2 both are NOT checked. Mikrotik is known to have bug
in these protocols when enabled with RADIUS server.
Figure - 5
10
________________________________________________________________________
In PPP->Profiles, make sure that you have set proper IP/Pool for the default profile.
Next , enable accounting in PPP->Secrets->Authentication & Accounting.
Figure - 6
PPP accounting settings
Hotspot Setup
Assuming you already have functional hotspot setup, go to Hotspot->Server Profiles and
select your hotspot profile.
Figure - 7
11
________________________________________________________________________
In the ‘Login’ Tab set Login by to ‘HTTP CHAP & Cookie’ as in the picture bellow :
Figure - 8
Setup new NAS in SAS3 , go to NAS -> Add
Figure - 9
12
________________________________________________________________________
After adding NAS(s) in SAS3 , you must restart the RADIUS service.
Go to Tools -> System Services , find RADIUS service , stop it and start it again.
Figure - 10
Now you should be ready to add users. If you have problems with users unable to connect ,
you can always check the RADIUS Log from Log->RADIUS Server. It will give you a good
hint on what is going on.
13

Installation Manual

Uploaded by

Copyright:

Available Formats

Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation Manual

Uploaded by

Copyright:

Available Formats

SAS3

Minimum hardware requirements :

- Mikrotik RouterOS NAS : 192.168.240.2

To send authentication and accounting requests to Radius server, You have to

1. Connect to your Mikrotik router using Winbox.

Set RADIUS incoming port to 1700 from RADIUS->Incoming

Make sure that mschap1 & m

Setup new NAS in SAS3 , go to NAS -> Add

You might also like

Installation Manual

Uploaded by

Copyright:

Available Formats

Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation Manual

Uploaded by

Copyright:

Available Formats

SAS3

Minimum hardware requirements :

- Mikrotik RouterOS NAS : 192.168.240.2

To send authentication and accounting requests to Radius server, You have to

1. Connect to your Mikrotik router using Winbox.

Set RADIUS incoming port to 1700 from RADIUS->Incoming

Make sure that ​mschap1​ & m

Setup new NAS in SAS3 , go to ​NAS -> Add

You might also like

Make sure that mschap1 & m

Setup new NAS in SAS3 , go to NAS -> Add