InterReach Fusion® Data Sheet

In-Building Wireless Networking System

InterReach Fusion offers the same superior performance as Unison in a multiband,
easy-to-install, economical package. It is ideal for mid-sized to large installations
containing dense, high-traffic environments such as convention centers, sporting
arenas and airports.

InterReach Fusion features an easy-to-deploy Double-star architecture with just

three types of components: A Main Hub that receives its radio frequency (RF)
Fusion
signals from a FlexWave™ Focus system, a base station or a repeater; up to 4-
Expansion Hubs that connect to the Main Hub via singlemode or multimode fiber
optics; and up to 32- Remote Access Units (RAUs) that connect to the Expansion
Hub via CATV cabling. Each RAU sends and receives RF signals to wireless devices
located within its coverage area. Administration is web-based.

PRODUCT HIGHLIGHTS
• More than 20,000 TE distributed antenna systems shipped to more than 150
countries

SingleStar
• True multi-band system with single set of electronics cabling and dedicated
One Port Option
capacity per band

• Delivers in-building wireless voice and data coverage over standard CATV cable

• Compatible with all major access protocols used worldwide including GPRS,
EDGE, CDMA2000, WCDMA, and LTE

• Unparalleled RF performance featuring high output power, low noise, zero-

loss distributed amplifier system that supports more channels and delivers the
ability to cover large areas with a minimal amount of equipment

• Software-selectable hub frequencies, system gain, and antenna output power

• Requires no electrical power at the remote antennas

• Uses common CATV wiring for easy, non-disruptive installation

• Intelligent, web-based software-controlled operations, administration and

maintenance capabilities support both on-site and remote configuration and
monitoring

• Built-in system diagnostics constantly monitors system health

InterReach Fusion® Data Sheet

The Fusion Hubs are 19" rack mountable units. The plenum
rated RAUs and the antennas connected to them are typically
mounted in ceiling spaces throughout a facility.
InterReach Fusion
The main hub and expansion hub are connected using single Expansion Hubs
Multi-band RAU
mode or multimode fiber. The CATV cabling between the and Antenna
hub and each of the eight RAUs can be up to 130-150 meters
(426-492 feet) long using 0.21 inch (5.5 mm) diameter RG-59
cabling. This length can be extended to 140-170 meters (459- Single or
Multi-mode Fiber
557 feet) with use of RG-6 cabling, or to 235-275 meters (771- CATV Cabling
InterReach Fusion
902 feet) using RG-11 cabling. Different cable types can be Main Hub
used simultaneously on a single hub.
Multi-band BTS
or Repeater
With a minimum of components and use of industry-standard
75 ohm CATV cabling, InterReach Fusion is simple and
inexpensive to install, especially compared to heavy, inflexible,
and invasive coaxial cabling. In addition, because power for
the RAUs is provided over the CATV cabling, no local power
is required, further simplifying installations.

FLEXIBLE OUTPUT LEVELS ALARMING

The system gain can be adjusted from 0 to 15 dB in 1 dB Fusion monitors over 170 parameters within the system.
increments. In addition, the output of any individual RAU can Three levels of alarms are available:
be attenuated 0 or 10 dB to provide controlled coverage in
specific building areas. • LEDs: Each unit has LEDs to indicate a fault in the
unit or a unit that is connected to it. For example,
if an RAU has a fault its LED will light red, the fault
SYSTEM ARCHITECTURE
information is sent to the Fusion Hub which also
The minimum configuration of a single Fusion system is displays a red LED at the RAU’s port connector.
one Main Hub, one Expansion Hub, and one RAU (1-1-1). • Contact Closures: Connect the Fusion Hub to a
The maximum configuration of a single system is one base station or external monitoring equipment.
Main Hub, four Expansion Hubs, and 32 RAUs (1-4-32).
• Status, Warning, and Fault messages: Displayed
Multiple systems may be deployed to cover larger areas or
on a PC/laptop that is running a standard Internet
campus applications.
Explorer browser or Standard Network Management
System SNMP application software tools.

Coaxial Jumper (1-6'):

Fiber Optic Cable RAU to Antenna
Max. Length:
500 m multimode fiber
6 km singlemode fiber

Expansion Hub

To/From Multi- Expansion

Band Base Station Hub
Fusion
or Repeater Main Hub Expansion Multi-band
Hub RAU
Expansion
Hub Up to 8 RAUs per Expansion Hub
for a possible total of 32 RAUs
Up to 4 Expansion Hubs
per Main Hub

2 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
InterReach Fusion® Data Sheet

TYPICAL SPECIFICATIONS
700 MHz (Block Lower A, B, C) and 700MHz (Block Upper C) DOWNLINK UPLINK
700 MHz (Block Lower A, B, C) RF Frequency (full band): 728 to 746 MHz 698 to 716 MHz
700 MHz (Block Lower A, B, C) Bandwidth: 18 MHz 18 MHz
700 MHz (Block Upper C) RF Frequency (full band): 746 to 757 MHz 776 to 787 MHz
700 MHz (Block Upper C) Bandwidth: 11 MHz 11 MHz
Waveform Accuracy (at maximum power)
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm/30 KHz): < -13 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

800 MHZ AND 900 MHZ SMR DOWNLINK UPLINK

800 MHz RF Frequency: 851 to 869 MHz 806 to 824 MHz
800 MHz Bandwidth: 18 MHz 18 MHz
900 MHz RF Frequency: 935 to 941 MHz 896 to 902 MHz
900 MHz Bandwidth: 6 MHz 6 MHz
Waveform Accuracy (at maximum power)
iDEN (SQE): < 25 dB < 25 dB
APCO 25 CQPSK (RMS EVM): < 6% < 6%
APCO 25 C4FM (Mag Err RMS): < 5% <5%
CDMA2000 (RHO): >0.99 >0.99
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm/100 KHz): < -13 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

850 MHz Cell DOWNLINK UPLINK

RF Frequency (full band): 869 to 894 MHz 824 to 849 MHz
Bandwidth: 25 MHz 25 MHz
Waveform Accuracy (at maximum power)
GSM (RMS Phase Error): < 2° < 2°
EDGE (RMS EVM): 3% 3%
CDMA2000 (RHO): > 0.99 > 0.99
WCDMA (RMS EVM): 5% 5%
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm/100 KHz): < -13 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

900 MHz GSM DOWNLINK UPLINK

RF Frequency (full band): 925 to 960 MHz 880 to 915 MHz
Bandwidth: 35 MHz 35 MHz
Waveform Accuracy (at maximum power)
GSM (RMS Phase Error): < 2° < 2°
EDGE (RMS EVM): 3% 3%
Spurious Emissions (dBm): < -36 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

1800 MHz DCS DOWNLINK UPLINK

RF Frequency (full band): 1805 to 1880 MHz 1710 to 1785 MHz
Bandwidth: 75 MHz 75 MHz
Waveform Accuracy (at maximum power)
GSM (RMS Phase Error): < 2° < 2°
EDGE (RMS EVM): 3% 3%
Spurious Emissions (dBm): < -30 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

3 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
InterReach Fusion® Data Sheet

TYPICAL SPECIFICATIONS (CONTINUED)

1900 MHz PCS DOWNLINK UPLINK

RF Frequency (full band: A-G)*: 1930 to 1995 MHz 1850 to 1915 MHz
Bandwidth**: 65 MHz 65 MHz
Waveform Accuracy (at maximum power)
GSM (RMS Phase Error): < 2° < 2°
EDGE (RMS EVM): 3% 3%
CDMA2000 (RHO): > 0.99 > 0.99
WCDMA (RMS EVM): 5% 5%
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm/MHz): < -13 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5
* FSN-8519-1, FSN-W1-1921-1, and FSN-W2-808519-1 downlink RF frequency is 1930 to 1990 MHz and uplink RF
frequency is 1850 to 1910 MHz.
** FSN-8519-1, FSN-W1-1921-1, and FSN-W2-808519-1 downlink and uplink bandwidth is 60MHz.
2100 AWS DOWNLINK UPLINK
RF Frequency (full band): 2110 to 2155 MHz 1710 to 1755 MHz
Bandwidth: 45 MHz 45 MHz
Waveform Accuracy (at maximum power)
WCDMA (RMS EVM): 5% 5%
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm/MHz): < -13 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

2100 MHz UMTS DOWNLINK UPLINK

RF Frequency (full band): 2110 to 2170 MHz 1920 to 1980 MHz
Bandwidth: 60 MHz 60 MHz
Waveform Accuracy (at maximum power)
WCDMA (RMS EVM): < 5% < 5%
Spurious Emissions (dBm): < -30 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5

2600 MHz DOWNLINK UPLINK

RF Frequency (full band): 2620 to 2690 MHz 2500 to 2570 MHz
Bandwidth: 70 MHz 70 MHz
Waveform Accuracy (at maximum power)
WCDMA (RMS EVM): 5% 5%
LTE (RMS EVM): 4% 4%
Spurious Emissions (dBm): < -30 —
System Group Delay (not including cable) (μs): < 0.5 < 0.5
Standard Power Standard Power High Power
700-900 MHz 1900-2700 MHz 1900-2700 MHz
Typical Typical Typical
RF Downlink Uplink Downlink Uplink Downlink Uplink
Average gain with 150 m CATV at 25°C (77°F) (dB)1: 15 15 15 15 20 15
Ripple with 150 m CATV (dB): 2.5 3 3.5 4 3.5 4
Output IP3 (dBm): 38 38 43
Input IP3 (dBm): -5 -5 -5
Output 1 dB Compression Point (dBm): 26 26 31
Noise Figure 1 MH-1 EH-8 RAUs (dB) 16 17 17
Noise Figure 1 MH-4 EH-32 RAUs (dB) 22 23 23

4 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
InterReach Fusion® Data Sheet

SPECIFICATIONS
PHYSICAL MAIN HUB EXPANSION HUB REMOTE ACCESS UNIT
IF/RF Connectors: 6 N, female (50 ohms), 8 F, female (CATV-75 ohms) 1 F, female (CATV-75 ohms)
1 Downlink/Uplink pair per band 1-2 N, female (antenna-50 ohms)
External 1 9-pin D-sub, female – –
Alarm Connector
(contact closure):
ADMIN/LAN Interface 1 RJ-45, female 1 RJ-45, female –
Connector: 1 9-pin D-sub, male for 1 9-pin D-sub, male
optional modem
Fiber Connectors2: 4 Pair, SC/APC3 1 Pair, SC/APC –
AC Power (Volts): Rating: Rating: 54V DC (from the E Hub)
100-240V AC, 1A, 50-60 Hz 100-240V AC, 6A, 50-60 Hz over CATV
Operating Range: 90-132V AC/ Operating Range: 90-132V AC/
170-250V AC auto–ranging 170-250V AC auto–ranging
DC Power (Volts): Operating Range: Operating Range: –
38-64V DC, 2.5A 38-64V DC, 14A
Power Consumption (W)4: 30 4 RAUs: 290 typical, 360 max –
8 RAUs: 500 typical, 630 max
Enclosure Dimensions5: 89 mm x 438 mm x 381 mm 89 mm x 438 mm x 381 mm 54 mm x 286 mm x 281 mm
(height x width x depth) (3.5" x 17.25" x 15") 2U (3.5" x 17.25" x 15") 2U (2.13" x 11.25" x 11.13")
Weight: <5.5 kg (<12 lb) <6.6 kg (<14.5 lb) <2.1 kg (<4.6 lb)

CABLING
Optical Fiber These specifications assume fiber optic cable, singlemode or multimode, with SC/APC connectors
Optical Power Budget: Uplink and Downlink Maximum: 3 dB optical
Optical power budget between Main Hub and Expansion Hub
Optical loss = ∑ (fiber loss + connector losses + splice losses + patch cord losses)
CATV The specifications in this document assume that CATV RG-59 cable is Belden 1506A, CATV RG-6 cable is
Belden 1695A, and CATV RG-11 cable is Belden 7732A or equivalent, with 75 ohm F connectors.
CATV Lengths for Fusion Fusion Wideband
Minimum: 0 m (0'); Minimum: 0 m (0');
Maximum: 150 m (492') with RG-59 Maximum: 130 m (426') with RG-59
Maximum: 170 m (557') with RG-6 Maximum: 140 m (459') with RG-6
Maximum: 275 m (902') with RG-11 Maximum: 235 m (771') with RG-11
ENVIRONMENTAL MAIN HUB REMOTE ACCESS UNIT
AND EXPANSION HUB
Operating Temperature: 0° to +45° C (+32° to +113° F) –25° to +45° C (–13° to +113° F)

Non-Operating Tempera- –20° to +85° C (-4° to +185° F) –25° to +85° C (–13° to +185° F)
ture:
Operating Humidity; Non- 5% to 95% 5% to 95%
Condensing:
COMPLIANCE

Safety:  L, CSA, CB Scheme certificate to IEC 60950, 3rd Edition, and IEC 60950-1, 1st Edition, with
U
all national deviations
EMC: FCC part 15 class A, EN 301 489-8, EN 301 489-23
Radio: FCC part 22, part 24, part 27, EN 301 502, EN 301 908-11, EN 301 908-15
Class 1 Laser Product: IEC 60825-1:1998-01 and IEC 60825-2:2000-05

1. The system gain is adjustable in 1 dB steps from 0 to 15 dB, and the Downlink or Uplink gain of each RAU can be attenuated 0 or 10 dB.
2. It is critical to system performance that only SC/APC fiber connectors are used throughout the fiber network, including fiber distribution panels.
3. FSN-1-MH-1P, FSN-2-MH-2-1P, FSN-W1-MH-2-1P, FSN-W2-MH-3-1P, FSN-W3-MH-1, and FSN-W4-MH-1 supports only 1 pair, SP/APC fibers.
4. Fusion Hub typical power consumption assumes that the CATV RG-6 cable length is no more than 170 m and RG-11 is no more than 275 m.
5. Excluding angle-brackets for 19" rack mounting of hub.

5 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
InterReach Fusion® Data Sheet

Standard Power
Output Power at RAU
Power per Carrier (dBm) per Band
RF Frequency Number of RF Carriers
Downlink Uplink 1 P-out 2 P-out 4 P-out 8 P-out
15.0 12.0 9.0 6.0 CDMA
850 Cell 869-894 824-849
FSN-8518-1 15.0 12.0 9.0 6.0 WCDMA
FSN-8521-1 26.0 20.0 14.0 9.0 GSM
900 GSM 925-960 880-915
FSN-9018-1 23.0 17.5 12.0 8.0 EDGE
FSN-9021-1 26.0 20.0 14.0 9.0 GSM
1800 DCS 1805-1880 1710-1785
FSN-W1-2118-1 23.0 17.5 12.0 8.0 EDGE
2100 UMTS 2110-2170 1920-1980 15.0 12.0 9.0 6.0 WCDMA

Standard Power
Output Power at RAU
Power per Carrier (dBm) per Band
RF Frequency Number of RF Carriers
Downlink Uplink 1 P-out 2 P-out 4 P-out 8 P-out
700 Upper C 746-757 776-787
18.0 15.0 12.0 9.0
LTE1
700 Lower ABC 728-746 698-716
26.0 20.0 14.0 9.0 GSM
23.0 17.5 12.0 8.0 EDGE
850 Cell 869-894 824-849 18.0 15.0 12.0 9.0 CDMA
18.0 15.0 12.0 9.0 WCDMA
FSN-8519-1
18.0 15.0 12.0 9.0 LTE
FSN-809019-2
16.5 13.0 9.0 5.5 iDEN
FSN-2-708519-1
24.0 18.5 12.5 7.5 APCO 25 C4FM
FSN-2-758519-1 800 SMR 851-869 806-824
17.0 14.0 11.0 8.0 CDMA
FSN-W1-1921-1
17.0 14.0 11.0 8.0 LTE
FSN-W2-808519-1
14.5 11.0 7.0 3.5 iDEN
FSN-W2-7021-1 900 SMR 935-940 896-901
23.0 16.5 10.5 5.5 APCO 25 C4FM
FSN-W2-7070-1
26.0 20.0 14.0 9.0 GSM
FSN-W2-7575-1
23.0 17.5 12.0 8.0 EDGE
FSN-W3-2626-1
1900 PCS2 1930-1995 1850-1915 18.0 15.0 12.0 9.0 CDMA
18.0 15.0 12.0 9.0 WCDMA
18.0 15.0 12.0 9.0 LTE
2110-2155 1710-1755 18.0 15.0 12.0 9.0 WCDMA
2100 AWS
18.0 15.0 12.0 9.0 LTE
18.0 15.0 12.0 9.0 WCDMA
2600 2620-2690 2500-2570
18.0 15.0 12.0 9.0 LTE
1
For FSN-W2-7021-1 RAU reduce each Power per Carrier by 4 dB for 700 Lower ABC and 700 Upper C bands.
2
FSN-8519-1, FSN-W1-1921-1, and FSN-W2-808519-1 downlink RF frequency is 1930 to 1990 MHz and uplink RF frequency is 1850 to 1910 MHz.

6 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
InterReach Fusion® Data Sheet

High Power
Output Power at RAU
Power per Carrier (dBm) per Band
RF Frequency Number of RF Carriers
Downlink Uplink 1 P-out 2 P-out 4 P-out 8 P-out
700 Upper C 746-757 776-787
18.0 15.0 12.0 9.0 LTE
700 Lower ABC 728-746 698-716
850 Cell 26.0 20.0 14.0 9.0 GSM
23.0 17.5 12.0 8.0 EDGE
869-894 824-849 18.0 15.0 12.0 9.0 CDMA
FSN-2-708519-1-HP 18.0 15.0 12.0 9.0 WCDMA
FSN-2-758519-1-HP 18.0 15.0 12.0 9.0 LTE
FSN-W4-702121-1-HP
1900 PCS 26.0 23.0 19.0 14.0 GSM
FSN-W4-752121-1-HP
FSN-21HP-1 26.0 22.5 17.0 13.0 EDGE
FSN-W1-21HP-1 1930-1995 1850-1915 23.0 20.0 17.0 14.0 CDMA
23.0 20.0 17.0 14.0 WCDMA
23.0 20.0 17.0 14.0 LTE
2100 AWS 23.0 20.0 17.0 14.0 WCDMA
2110-2155 1710-1755
23.0 20.0 17.0 14.0 LTE
2100 UMTS 2110-2170 1920-1980 22.0 19.0 16.0 13.0 WCDMA

ORDERING INFORMATION

Main Main Expansion Expansion

Hub (AC) Hub (DC) Hub (AC) Hub (DC) RAU
Band Part Number Part Number Part Number Part Number Part Number
850 1800 FSN-8518-1
850 1900 FSN-8519-1
850 2100 FSN-8521-1
900 1800 FSN-1-MH-1 FSN-1-MHDC-1 FSN-EH-2 FSN-EHDC-2 FSN-9018-1
900 2100 FSN-9021-1
2100HP FSN-21HP-1
800 900 1900 FSN-809019-2
700UC 850 1900 FSN-2-758519-1
FSN-2-MH-2 FSN-2-MHDC-2 FSN-EH-2 FSN-EHDC-2
700ABC 850 1900 FSN-2-708519-1
1900 AWS FSN-W1-1921-1
1800 2100 FSN-W1-MH-2 FSN-W1-MHDC-2 FSN-W1-EH-2 FSN-W1-EHDC-2 FSN-W1-2118-1
2100HP FSN-W1-21HP-1
800 850 1900 FSN-W2-808519-1
700 ABC 700 UC AWS FSN-W2-7021-1
FSN-W2-MH-3 FSN-W2-MHDC-3 FSN-W1-EH-2 FSN-W1-EHDC-2
700 UC 700 UC FSN-W2-7575-1
700 ABC 700 ABC FSN-W2-7070-1
2600 2600 FSN-W3-MH-1 N/A FSN-W1-EH-2 FSN-W1-EHDC-2 FSN-W3-2626-1
700UC 850 1900 HP FSN-2-758519-1-HP
FSN-2-MH-2 FSN-2-MHDC-2 FSN-EH-2 FSN-EHDC-2
700ABC 850 1900 HP FSN-2-708519-1-HP
700UC AWS HP AWS HP FSN-W4-752121-1-HP
FSN-W4-MH-1 FSN-W4-MHDC-1 FSN-W1-EH-2 FSN-W1-EHDC-2
700ABC AWS HP AWS HP FSN-W4-702121-1-HP

7 www.te.com/WirelessSolutions  1-800-366-3891  12/12 314014AE
DATA SHEET

Contact us: TE Connectivity, TE connectivity (logo), Tyco Electronics, and TE (logo) are trademarks of the TE Connectivity Ltd. family of companies
P.O. Box 1101 and its licensors.
Minneapolis, Minnesota
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this document, TE Connectivity does
USA 55440-1101 not guarantee that it is error-free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is
Tel: 1-800-366-3891 accurate, correct, reliable or current. TE Connectivity reserves the right to make any adjustments to the information contained herein at
Fax: 1-952-917-3237 any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the information contained herein, including,
but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult
www.te.com/WirelessSolutions TE Connectivity for the latest dimensions and design specifications.

Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved.

314014AE 12/12 Original © 2012