Brushbond Roof Guard

constructive solutions

High build fibre Reinforced Acrylic Waterproofing

render for roofing Physical Properties

Uses Solid Content : 70 %

Brushbond Roof Guard is high build fibre reinforced Tensile strength
ASTM D 412 : 1.10 Mpa
seamless waterproofing render suitable for waterproofing of
Elongation
old & new roofs, it is a polymer base product applied in three
ASTM D12 : 100%
OR more coats & each coat with different colours for
Resistance to ageing due to : 1000 hours
monitoring correct thickness.
UV radiation ASTM D4587 E : No Change
The product can be applied directly on existing concrete,
brickbat coba, and screed concrete even without removal Rapid Chloride :
provided the substrates are sound enough for application of Penetration ASTM C 1202-03 : Very low
the coating avoiding the risk of damage to the old roof Pull off adhesion
associated while removing of the existing overlays. The ASTM D4541 : 0.92 Mpa
product provides a seamless, tough durable water resistant
coating which can withstand light pedestrian traffic and also
has excellent weather resistance for exterior applications. Resistance to Algae growth
ASTM D 5589-97 : Passes, Zero rating
Advantages Permeability (mm)
(BSEN 12390 part 8) : 5.0
High Build system provides higher dry film
thickness of more than 1mm in three coats. Water vapour transmission
The product can applied directly on existing sound (ASTM E96) : 6.0g/m² h
concrete, brickbat coba, screed concrete even
without removal
No protection screed required eliminating the Application Instructions
additional weight due to protection layer
Excellent barrier to carbon dioxide, chloride and Surface Preparation
sulphate ions.
Allows water vapour to escape from the structure. All the surfaces which are to receive Brushbond Roof Guard
High resistance to the effect of long-term must be free from oil, grease, wax, dirt or any other form of
weathering,
Durable in all climate conditions including UV foreign matter which might affect adhesion. Spalled and
attack. deeply disintegrated concrete should be removed to sound
Excellent bond to concrete and masonry. concrete and repaired with Fosroc Renderoc System.
Good crack accommodation capacity.
Minimum surface preparation needed and low
labour Mixing
Standards compliance
Tested to ASTM D2240, ASTM D4541, ASTM D412, The contents of Brushbond Roof Guard shall be thoroughly
ASTM G 154, ASTM E 96
stirred for at least 2 minutes using a slow speed (300-400
Description RPM) drill machine attached with a mixing paddle.
Brushbond Roof Guard is a single component acrylic Retempering with water should not be done. Keep on stirring
polymer modified, fibre reinforced high build & easy roller during application.
applied / brushable coating available in different colours for
application in multiple layers, minimum 3 layer application is Application
recommended for best performance.
For best results, surfaces should be damp. In order to
Technical Support Obtain the protective properties of Brushbond Roof Guard it
Fosroc offers technical support service to specifiers, end- is important that the correct rates of application are observed.
users and contractors, as well as on-site technical Use a short stiff brush preferably 120-150mm width and
Assistance in locations all over the country. apply the mixed material like paint.
Brushbond Roof Guard

The application of Brushbond Roof Guard should not be

done if the temperature of the substrate is below 10 0C. When
applying Brushbond Roof Guard on hot substrates i.e., over
300C surface temperature, saturate the surface with water.
Apply Brushbond Roof Guard primer ( one litre of Brushbond
Roof Guard mixed with 1 litre of water) followed by
application of Brushbond Roof Guard in 3 coats to achieve
total dry film thickness of 1mm . The second & third coat of
Brushbond Roof Guard shall be applied as soon as the first
coat has reached touch dry state. If planning for protection
screed allow the Brushbond Roof Guard coating to dry
before covering with screed, sprinkle coarse sand on wet
surface of final coating for better adhesion of screed.
Brushbond Roof Guard

Cleaning
Brushbond Roof Guard should be removed from tools and
Shelf life & Storage
equipment with clean water immediately after use. Hardened
material can only be removed mechanically. Shelf life is 12 months from the date of manufacturing in
unopened condition. Store in a cool & dry place
Estimating
Packing : 4 & 20 litre
2
Health and Safety
Coverage : 0.5 liter / m / coat (Three coat application is
recommended. Brushbond Roof Guard system is non-toxic but alkaline in
nature. Gloves and goggles should be worn while handling.
Precautions & Limitations
Any splashes on the skin or eyes should be washed off with
Do not apply during rains; substrate must be in SSD condi- clean water. In the event of prolonged irritation, medical ad-
tion for application of primer. The product is designed only vice should be sought. Brushbond Roof Guard system is
for foot traffic and not vehicular movement or movement of non-flammable.
machinery or equipment’s.

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification or
information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
Fosroc Chemicals directly or indirectly arising from the use of its products whether or not in accordance with any
(India) Pvt. Ltd. advice, specification, recommendation or information given by it.
Head Office
“Sapthagiri Palace”, No.38, telephone Fax e-mail
II & III Floor, 12th Cross, ++91 80-23551500 ++91 80-23551510 [email protected]
CBI Road, Ganganagar North,
Bangalore 560 024

Regional Offices

Bangalore Mumbai Noida Kolkata

“Sapthagiri Palace”, No. 38 1401/1402, 14 Floor, D-166 Sector 10 304, Jodhpur Park
II & III Floor, 12th Cross, A-Wing’The Great Eastern Summit’ Noida, Kolkata 700 068
CBI Road, Ganganagar North, Sector-15, CBD, Belapur UP 201 301 Ph:033-65343188
Bangalore 560 032. Navi Mumbai 400 614 Ph:0120-4270620 Fax: 033-2499-0280
Ph:080-23551500 Ph: 022 -43406800-04
Fax : 080-23551510

www.fosroc.com
page 2 of 2 INDIA/2013/0209/B