ECU Chip Tuning

BDM100

1. Copy whole folder into hard disk.

2. Copy both files from CRT folder into WINDOWS/SYSTEM32 folder

3. Connect interface to USB and install drivers from DRIVERS directory.

4. Run loader-all4.exe

User Manual in root

CMD1251

Copy the folder CAN-BUS in 1251 this CD anywhere on your hard drive. For convenience we
recommend the desktop.

Insert the interface and associate the drivers in the drivers folder inside folder mother CAN-BUS
1251

Copy the file CMD1.CRT always present in the folder CAN-BUS 1251

Windows \ System32

If you do not have windows installed on the Windows folder, use the folder name where installed.

If you already have a file Cmd1.crt you could try to leave that. Run the file inside the folder
MpcProg_CAN_1251.exe CAN-BUS 1251and send mail through the code that is returned.

You're going to always copy the folder where you installed the program (CAN-BUS 1251 unless you
changed the name).

Now double-click the file you’ve been sent. The system will tell you that was added to windows
registry.

Now you can run again MpcProg_CAN_1251.exe.

Gal1260
 This article will guide you how to correctly install Galletto 1260
USB cable drivers on Windows.

Galletto 1260 Chip Tuning

STEP 1: Download and Install Galletto 1260 Tuning

STEP 2: Install Drivers

Go to Control Panel.

 Windows Vista/7/8/10: Control Panel » System » Device Manager

 Windows XP: Control Panel » System » "Hardware" tab » Device Manager

Expand "Other devices" or "Ports (COM & LPT)". Under them you will see either "USB Serial
Port" or "EOBD2" or another different name that only shows up when cable is plugged in.

Whichever it is, right-click on it and choose: Update Driver Software (see below example pic)

Then Browse to the folder where you installed Galletto 1260 in Step 1. (see below example pic)
That's it!

When you click "Next", Windows will auto-install all drivers. If it's successful, then you can connect
cable to your car, and connect to car via software.

KWP2000

Manual in root.

MPPS

MPPS programmer guide HDI Tuning Ltd www.hdi-tuning.co.uk Disclaimer: This information has
been provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2 ECU. By following this
guide you agree that all actions are taken at your own risk. We are not responsible for ECU damage
caused by incorrect use of the tool described in this document. However, HDI Tuning Ltd are capable
of repairing an ECU in the event that programming does not complete successfully. How to
read/write your Bosch EDC15 ECU using the MPPS tool This guide will explain how to setup the
MPPS programmer tool. The MPPS programmer can be used to read and write your Peugeot/Citroen
EDC15C2 ECU. Purchasing your MPPS tool The best place to buy the MPPS tool is from eBay. This
typically costs around £25 from a UK seller. It is advisable to use a seller who sells tested tools. Setup
and installation First , open Mpps Setup v12.0.0.6.exe (if using an operating system later than
windows XP you must right click the icon and then run in XP compatibility mode). The setup for your
tool may differ slightly depending on the software version supplied with your tool. Select ‘Install’ to
proceed. Select your language and then ‘Next’ to proceed. It is recommended that you restart your
computer after the installation is complete. When finished select ‘Finish’ to close the software.
MPPS programmer guide HDI Tuning Ltd www.hdi-tuning.co.uk Disclaimer: This information has
been provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2 ECU. By following this
guide you agree that all actions are taken at your own risk. We are not responsible for ECU damage
caused by incorrect use of the tool described in this document. However, HDI Tuning Ltd are capable
of repairing an ECU in the event that programming does not complete successfully. Insert the MPPS
reader into your computer's USB port. Once you have inserted the MPPS tool you should see ‘Found
new hardware wizard’. Select ’No, not this time’ from the menu then select ‘Next’ (now you can
locate the driver manually). From the menu select ’Install from a list or specific location (Advanced)’
then select ‘Next’ MPPS programmer guide HDI Tuning Ltd www.hdi-tuning.co.uk Disclaimer: This
information has been provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2 ECU.
By following this guide you agree that all actions are taken at your own risk. We are not responsible
for ECU damage caused by incorrect use of the tool described in this document. However, HDI
Tuning Ltd are capable of repairing an ECU in the event that programming does not complete
successfully. From the menu check ‘Search for the best drivers in these locations’ then check ‘Include
this location in the search. Select ‘Browse’ you should now get a small window open to browse for
the driver. The driver location should be located here: ‘C:\MPPS\Device Driver’ Once the folder has
been selected you can select ‘Next’ and windows will find the driver in that folder. MPPS
programmer guide HDI Tuning Ltd www.hdi-tuning.co.uk Disclaimer: This information has been
provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2 ECU. By following this
guide you agree that all actions are taken at your own risk. We are not responsible for ECU damage
caused by incorrect use of the tool described in this document. However, HDI Tuning Ltd are capable
of repairing an ECU in the event that programming does not complete successfully. Select ‘Finish’ to
complete installation. MPPS programmer guide HDI Tuning Ltd www.hdi-tuning.co.uk Disclaimer:
This information has been provided by HDI Tuning Ltd to help in programming your Bosch EDC15C2
ECU. By following this guide you agree that all actions are taken at your own risk. We are not
responsible for ECU damage caused by incorrect use of the tool described in this document.
However, HDI Tuning Ltd are capable of repairing an ECU in the event that programming does not
complete successfully. Reading your original ECU data The MPPS tool requires a stable laptop
computer with a good battery. For best results use windows XP and use a laptop with a fully charged
battery. Contradictory to what some may say, we recommend you don’t attach your laptop's power
supply during flashing as this can induce a ground loop which may crash the MPPS software. Instead,
be certain you have at least 45 minutes of battery (the read/write process only takes just over a
minute, however after finding the OBD port, opening the software etc, you may take longer than
anticipated). It is very important not to disturb your computer while you are reading/writing the
ECU.  Remain still to avoid moving any wires or connections.  Close all other programs on your
computer beforehand.  Turn off fan, heated rear screen, remove fuses from any amplifiers, turn off
the head unit or remove the front (before starting this process). 1. Ensure your car is switched off.
Locate the diagnostic port and connect the tool. 2. Connect the USB cable to your laptop. 3. Open
the MPPS software through the shortcut on your desktop. 4. Once open, switch on your ignition to 2
clicks (until the engine check light is shown on your dash). 5. Select your car and engine from the
menus provided. 6. Select ECU Id on the left. MPPS programmer guide HDI Tuning Ltd www.hdi-
tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd to help in
programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions are taken
at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool
described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the event
that programming does not complete successfully. 7. Once the ECU number is displayed, you are
ready to read your ECU. Select ‘Read’. 8. The reading process takes just over a minute to complete.
Once completed, save the file in an appropriate place with the file name of: YourName.bin 9. Once
the read has finished, follow the on screen steps to switch off keys>wait 5 seconds>switch on keys
10. When finished, switch off the ignition and close the program by selecting ‘Exit’ in the bottom left
corner. It is now safe to remove the OBD lead from your car. 11. You can now email your original
ECU data to [email protected] MPPS programmer guide HDI Tuning Ltd www.hdi-
tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd to help in
programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions are taken
at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool
described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the event
that programming does not complete successfully. Writing your ECU 1. Ensure your car is switched
off. Locate the diagnostic port and connect the tool. 2. Connect the USB cable to your laptop. 3.
Open the MPPS software through the shortcut on your desktop. 4. Once open, switch on your
ignition to 2 clicks (until the engine check light is shown on your dash). 5. Select your car and engine
from the menus provided. 6. Select ECU Id on the left. 7. Once the ECU number is displayed you can
the select ‘write’. 8. Locate your remapped file and then select ‘ok’. 9. Once the write has finished,
follow the on screen steps to switch off keys>wait 5 seconds>switch on keys. 10. Once this is
completed, switch off the ignition and close the program by selecting ‘Exit’ in the bottom left corner.
It is now safe to remove the OBD lead from your car. Your car is now remapped and ready to go,
take the car for a test drive and enjoy! Be sure to leave a review on our Facebook page at
www.facebook.com/HDITuningLimited MPPS programmer guide HDI Tuning Ltd www.hdi-
tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd to help in
programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions are taken
at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool
described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the event
that programming does not complete successfully. Trouble shooting during installation Follow the
guide below if windows fails to install the correct driver for your MPPS tool. If installation was
unsuccessful, open the start menu and right click on ‘My computer’ then select ‘Manage’ from the
drop down menu Once open, select ‘Device manager’ from the menu on the left. Search through the
list to find any items with a yellow question mark displayed to the left. MPPS programmer guide HDI
Tuning Ltd www.hdi-tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd
to help in programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions
are taken at your own risk. We are not responsible for ECU damage caused by incorrect use of the
tool described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the
event that programming does not complete successfully. Once the marked item has been located,
right click the item and select ‘Properties’ from the drop down menu. Select the tab named ‘Driver’
located at the top and then select ‘Update Driver...’ to proceed. MPPS programmer guide HDI Tuning
Ltd www.hdi-tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd to help
in programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions are
taken at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool
described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the event
that programming does not complete successfully. From the menu select ‘Search for the best drivers
in these locations’ then select ‘Browse’ you should now get a small window open to browse for the
driver. Select the folder: ‘C:\MPPS\Device Driver’ then select ‘Ok’ to proceed. Once the driver folder
has been located ‘Select’ next to proceed. MPPS programmer guide HDI Tuning Ltd www.hdi-
tuning.co.uk Disclaimer: This information has been provided by HDI Tuning Ltd to help in
programming your Bosch EDC15C2 ECU. By following this guide you agree that all actions are taken
at your own risk. We are not responsible for ECU damage caused by incorrect use of the tool
described in this document. However, HDI Tuning Ltd are capable of repairing an ECU in the event
that programming does not complete successfully. Select ‘Continue Anyway’ to proceed.