D7S

No.
9915815-2A (1 /31)
OMRON Corporation
OMRON SWITCH & DEVICES Corporation
Issued By Checked By Approved By

RoHS Directive Support
K. Fujiwara S.Fukui
■For Reference
Product Specifications
Item Name Vibration Sensor
Model D7S-A0001
Registration Part Number for Customer

Item Name:
Item Number:
Receipt Stamp (For Receipt Purpose Only) Submitted Stamp
Handled By
Distribution
Copies
Customer
Sales
No. 9915815-2A (2 /31)
Item Name: Vibration Sensor

Product Specifications Model: D7S-A0001
1. Model
D7S-A0001
2. Functions
The D7S provides the following functions.
(a) Basic Functions
When an earthquake occurs with a seismic intensity equivalent to 5 Upper or higher on the JMA Seismic
Intensity Scale, the D7S will activate the shutoff output to notify the user that an earthquake has occurred.
(The basic functions can be used without using communications.)
(b) Communications
2
The D7S is equipped with I C communications to allow the user to acquire and set the following
information.
① SI values of the past five earthquakes that occurred
② Peak acceleration of the past five earthquakes that occurred
③ Execute self-diagnostic instructions and get the results
④ Switch to Initial Installation Mode via communications
3. Purpose
Vibration Sensor
No. 9915815-2A (3 /31)
4. Appearance
1) Package: Surface-mounting
2) Outline Drawing: Drawing No. 9499978-7
3）Taping and Packaging Outline Drawing: Drawing No. 9499980-9
4) Terminal Arrangement (Top View):
1 10
2 9
3 8
4 7
5 6
Signal Function Direction Description

1 VCC Power supply -
voltage
2 INT1 Shutoff output OUT An open-drain output.
Goes active (ON) when the shutoff judgment
condition and collapse detection condition are met.
3 INT2 Processing OUT An open-drain output.
notification Goes active (ON) during earthquake calculations,
output offset acquisition, and self-diagnostic processing.
4 SCL 2 IN Pull up the voltage to VCC even when you do not
I C clock 2
use I C.
5 SDA 2 IN/OUT Pull up the voltage to VCC even when you do not
I C data 2
use I C.
6 GND Power supply -
ground
7 SETTING Initial setting IN Changes the Sensor to Initial Installation Mode for an
input input from an external device.
Normal Mode: High
Initial Installation Mode: Low
8 NC Not connected - Completely floating and cannot be connected to
another line.
9 VCC Power supply -
voltage
10 GND Power supply -
ground
No. 9915815-2A (4 /31)
5. Block Diagram
D7S
6. Recommended Circuit Diagram
Note: Regardless of whether or not you are using I2C, pull up pins 4 and 5 to Vcc with 2.2 to 10 kΩ resistors.
No. 9915815-2A (5 /31)
7. Recommended Mounting Pattern
Recommended Mounting Conditions

Peak Mounting Temperature: 245 C min. (260 C max.)
Reflow Time: 64 to 80 s (220 C)
Reflow Repetitions: Up to 2 times
Recommended Land Pattern
* Mounting other components or placing wiring patterns in the area marked with diagonal lines is prohibited.
Also take care so that foreign material does not become stuck under the chip in the area marked with diagonal
lines.
8. Ratings:
(1) Absolute Maximum Ratings
Item Symbol Min. Max. Unit
Power Supply Voltage Vcc -0.3 6.0 V
I/O Terminals Vin -0.3 6.0 V
(2) Electrical Characteristics

Item Symbol Min. Max. Unit
Power Supply Voltage Vcc 2.1 5.5 V
Current Consumption at
Is - 90 uA
Standby
Average Current
Consumption during Iw - 300 uA
Processing
Terminal Input Voltage
Vin -0.3 5.5 V
Range
Sink Current (INT1 and
Is - 16 mA
INT2)
No. 9915815-2A (6 /31)
(3) I2C Digital Characteristics (Vcc = 2.1 to 5.5 V and Ta = 25 C unless otherwise specified.)
Item Symbol Min. Typ. Max. Unit Remarks
Input Voltage Vin -0.3 - 5.5 V All input and output
Range terminals.
Digital Input Low Vil - - 0.6 V
Voltage
Digital Input High Vih 1.4 - - V
Voltage
Pull-up Resistor Rpullup 2.2 10 kΩ Recommended value for
external resistor.
(4) Environmental Performance

Item Symbol Min. Typ. Max. Unit Remarks
Operating Topr -30 - 70 C With no condensation
Temperature or icing.
Storage Tstr -40 - 80 C With no condensation
Temperature or icing.
Ambient Hopr 25 - 95 %RH With no condensation
Humidity or icing.
Storage Hstr 25 - 95 %RH With no condensation
Humidity or icing.
Mounting Angle θ -5 0 +5 Degree -
9. Sensor Characteristics (Vcc = 3.0 V and Ta = 25 C unless otherwise specified.)

Item Min. Typ. Max. Unit Remarks
Vibration Output Signal output in the following Japan Electrical Wiring
Specification waveforms. (Activated by a sine Devices and Equipment
wave of 250 gal and a period of 0.3 Industries Association
s, 0.5 s, or 0.7 s. Not activated by a standard.
sine wave of 80 gal and a period of Compliant with Appendix
0.3 s, 0.5 s, or 0.7 s or by a sine 2 of JWDS 0007.
wave of 250 gal and a period of 0.1
s.)
Acceleration Output 95 105 %
Specification (Gain)
Acceleration Output -180 180 gal
Specification (Offset)
10. Operation Overview
The Sensor has the following functions.
1) Shutoff Signal Output Function

This function calculates the SI value and PGA (peak acceleration value) based on the acceleration
values acquired from the acceleration sensor, and then it outputs the shutoff signal by pulling the INT1
pin low if the waveform conditions defined in JEWA standard JWDS 0007 Appendix 2 are met. The
acceleration offset is automatically updated at this time to eliminate successive offset drift in the
acceleration sensor.
No. 9915815-2A (7 /31)
2) Collapse Detection Function

This function compares the Initial Installation Mode offset values and the offset values that were
automatically updated. If the values differ by a large degree, the function will detect this as significant tilting
compared to initial installation (an amount approximately equivalent to a 20 inclination), and it will output the
collapse detection output from INT1.
3) Information Acquisition Function via I2C Communications

The following functions have been implemented via the integrated I2C communications.
・The SI value and PGA that are being calculated during an earthquake can be read via I2C
communications.
・After the end of earthquake processing, the SI value and PGA for that earthquake can be read from
the Vibration Sensor's memory (up to five waveforms).
11. Operation Mode Details

(1) Status Transitions
This Sensor switches to Normal Mode when the power supply is turned ON.
The types of modes are Normal Mode (the mode that determines earthquakes and performs the
shutoff judgment with the SI calculation), Initial Installation Mode, Offset Acquisition Mode, and
Self-Diagnostic Mode. The mode is changed by changing the content of register address MODE
(0x1003) via I2C communications.
You can switch to Initial Installation Mode, Offset Acquisition Mode, and Self-Diagnostic Mode only
from Normal Mode. The mode is restored to Normal Mode after Initial Installation Mode, Offset
Acquisition Mode, and Self-Diagnostic Mode are ended.
Power Supply ON
Mode Mode
Changed Changed Initial
Self-Diagnostic Normal Mode Installation
Mode Mode
Completed Completed
Mode Completed
Changed
Offset Acquisition
Mode
(2) Normal Mode

In Normal Mode, the Sensor first acquires the current 3-axis acceleration values and holds them as
the offset. If the CTRL register (0x1004) setting is 0: YZ axes, 1: XZ axes, 2: XY axes, or 4: Switch
axes at installation, the latest offset data (register addresses 0x4100 to 0x4114) values are updated. If
the CTRL register (0x1004) setting is 3: Auto switch axes, the latest offset data (register addresses
0x4100 to 0x4114) values and initial installation data (register addresses 0x4000 to 0x4014) values
are automatically updated. Then the current tilting of the Sensor is judged and the two axes in the
horizontal direction are automatically calculated to determine the axes to use for the SI value.
No. 9915815-2A (8 /31)
After the offset values are calculated, the offset values in the initial installation data and latest offset
data are compared. If there is a large difference in those values, the Sensor is judged as having titled
from the initial installation state, and the collapse detection output is output from the INT1 pin. To set
the INT1 output to inactive after it has become active, you must read the EVENT register (0x1002),
switch to Initial Installation Mode, or turn OFF the power supply.
The Sensor then transitions to the standby status. This status is normally maintained while an
earthquake does not occur.
When an earthquake occurs, the earthquake processing starts. The Vibration Sensor calculates the SI
value and PGA (peak acceleration value) based on the acceleration values acquired from the
acceleration sensor every 320 ms. If the waveform conditions defined in JEWA standard JWDS 0007
Appendix 2 are met during the calculations, the shutoff signal is output from the INT1 pin. The SI value
and PGA that are being calculated during this earthquake processing can be read via I2C
communications. The INT2 output is also activated (ON) during earthquake processing. Earthquake
processing is performed for two minutes.
After the end of earthquake processing, the SI value and PGA for that earthquake are stored in the
Vibration Sensor's memory (up to five waveforms). The data for the five latest waveforms are stored in
memory, as well as the data for the five waveforms with the largest SI values. If INT1 is being output
after the data is stored, INT1 is set to inactive.
The Sensor then checks if the earthquake is still occurring. If the earthquake is still occurring,
earthquake processing is once again performed. If the Sensor judges that the earthquake has ended,
the offset values are acquired. The latest offset data (register addresses 0x4100 to 0x4114) values are
updated at this time.
The Sensor then returns to the initial settings and switches to the standby status.
No. 9915815-2A (9 /31)
Normal Mode
Offset Acquisition
Initial Settings
Standby
NO
Earthquake?
YES
Earthquake
Processing
Offset
Acquisition NO Shutoff Output
Conditions Met?
YES
INT1
ACTIVE
NO
Earthquake Processing
Ended?
YES
Save Data
INT1
INACTIVE
NO
Earthquake?
YES
(3) Initial Installation Mode

The Sensor switches to Initial Installation Mode when that mode is specified in the MODE register
(0x1003) or when the SETTING pin is pulled low.
In Initial Installation Mode, the Sensor first acquires the current 3-axis acceleration values and holds
them as the offset. The latest offset data (register addresses 0x4100 to 0x4114) values and initial
installation data (register addresses 0x4000 to 0x4014) values are updated at this time.
If the CTRL register (0x1004) setting is 3: Auto switch axes or 4: Switch axes at installation, the
current tilting of the Sensor is judged and the two axes in the horizontal direction are automatically
calculated to determine the axes to use for the SI value.
No. 9915815-2A (10 /31)
Initial Installation
Mode
Offset Acquisition
NO
Offset Acquired?
YES
Update Latest
Offset Values
Update Initial
Installation Data
XY, XZ, YZ
Confirm Switch Axes
Setting
Switch Axes at Installation or
Auto Switch Axes
Auto Judge Axes

to Use
Store Used Axes

Information
END
(4) Offset Acquisition Mode

The Sensor switches to Offset Acquisition Mode when that mode is specified in the MODE register
(0x1003).
In Offset Acquisition Mode, the Sensor first acquires the current 3-axis acceleration values and holds
them as the offset. The latest offset data (register addresses 0x4100 to 0x4114) values are updated at
this time.
Offset Acquisition
Mode
Acquire Offset
NO
Offset Acquired?
YES
Update Latest
Offset Values
NO Collapse Detected?
YES
INT1
ACTIVE
END
No. 9915815-2A (11 /31)
(5) Self-Diagnostic Mode

The Sensor switches to Self-Diagnostic Mode when that mode is specified in the MODE register
(0x1003).
When an acceleration sensor failure has been determined and is judged as a fault, the event_selftest
bit in the EVENT register (0x1002) changes to 1. The self-diagnostic data (register addresses 0x4200
to 0x420E) is also updated.
No. 9915815-2A (12 /31)
12. I2C Communications Protocol
Device Type Slave

2
Communications Method IC
Baud Rate 400 kbps
Transmission Code Binary
Slave Address 0x55
2
I C Clock Stretching Enabled
The I2C slave address (0x55) is expressed as follows.
Bit bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

Add[6] Add[5] Add[4] Add[3] Add[2] Add[1] Add[0] R/W
Value 1 0 1 0 1 0 1 1/0
When writing: Set the LSB of the slave address to 0 so that the address is AAh (1010_1010b).
When reading: Set the LSB of the slave address to 1 so that the address is ABh (1010_1011b).
Symbols
START: START condition
STOP: STOP condition
SACK: Acknowledge by Slave
MACK: Acknowledge by Master
MNACK: Not Acknowledge by Master
*Attention: When the non-volatile memory in the Sensor is being updated, NACK may be returned for an
2
I C communications request to prevent memory data corruption.
(1) Single Write Access Protocol

The following diagram is an example of the protocol when overwriting a register address specified as
a 16-bit value with an 8-bit setting value.
(2) Multi Write Access Protocol

The following diagram is an example of the protocol when overwriting a register address specified as
a 16-bit value with consecutive setting values. The register address is incremented in the amount of
register addresses specified by the master, and the setting values for those register addresses are
overwritten.
No. 9915815-2A (13 /31)
(3) Single Read Access Protocol

The following diagram is an example of the protocol when reading data from a register address
specified as a 16-bit value.
(4) Multi Read Access Protocol

The following diagram is an example of the protocol when reading consecutive items of data
starting from a register address specified as a 16-bit value. The register address is incremented in
the amount of register addresses specified by the master, and the data held in those register
addresses can be read.
No. 9915815-2A (14 /31)
13. Implemented Registers

(1) Registers List
Item Register Register Name Data Default

項目レジスタアドレスレジスタ名名称 R/W 初期値
Address bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 Value
0x 10 00 STATE R - - - - - state[2:0] 0x00
Status axis_state
状態 0x 10 01 AXIS_STATE R - - - - - - 0x02
[1:0]
event_off event_sel event_col event_sh
0x 10 02 EVENT R - - - - 0x00
set ftest lapse ut
0x 10 03 MODE R/W - - - - - mode[2:0] 0x01
Change ctrl_thres
設定変更 0x 10 04 CTRL R/W - ctrl_axis[2:0] - - - 0x40
Status h
clear_set clear_rec clear_self clear_qua
0x 10 05 CLEAR_COMMAND R/W - - - - 0x00
_offset ent_offse test ke
0x
Earthquake- 20 00 MAIN_SI_H
地震関連
Related R main_si[15:0] 0x0000
Data0x 20 01 MAIN_SI_L
データ
0x
(During an 20 02 MAIN_PGA_H
(地震中)
Earthquake) R main_pga[15:0] 0x0000
0x 20 03 MAIN_PGA_L
0x 30 00 N1_MAIN_OFFSET_X_H
R n1_main_offset_x[15:0] 0x0000
0x 30 01 N1_MAIN_OFFSET_X_L
0x 30 02 N1_MAIN_OFFSET_Y_H
R n1_main_offset_y[15:0] 0x0000
0x 30 03 N1_MAIN_OFFSET_Y_L
Latest 0x 30 04 N1_MAIN_OFFSET_Z_H
R n1_main_offset_z[15:0] 0x0000
Data 1 0x 30 05 N1_MAIN_OFFSET_Z_L
最新データ1
0x 30 06 N1_MAIN_T_AVE_H
R n1_main_t_ave[15:0] 0x0000
0x 30 07 N1_MAIN_T_AVE_L
0x 30 08 N1_MAIN_SI_H
R n1_main_si[15:0] 0x0000
0x 30 09 N1_MAIN_SI_L
0x 30 0A N1_MAIN_PGA_H
R n1_main_pga[15:0] 0x0000
0x 30 0B N1_MAIN_PGA_L
0x 31 04 N2_MAIN_OFFSET_Z_H
Latest R n2_main_offset_z[15:0] 0x0000
0x 31 05 N2_MAIN_OFFSET_Z_L
最新データ2
Data 2
R n2_main_t_ave[15:0] 0x0000
R n2_main_si[15:0] 0x0000
R n2_main_pga[15:0] 0x0000
Latest
最新データ3
R n3_main_t_ave[15:0] 0x0000
R n3_main_si[15:0] 0x0000
R n3_main_pga[15:0] 0x0000
No. 9915815-2A (15 /31)
Data 4
0x 33 05 N4_MAIN_OFFSET_Z_L
最新データ4
R n4_main_t_ave[15:0] 0x0000
R n4_main_si[15:0] 0x0000
R n4_main_pga[15:0] 0x0000
最新データ5
R n5_main_t_ave[15:0] 0x0000
R n5_main_si[15:0] 0x0000
R n5_main_pga[15:0] 0x0000
0x 35 00 M1_MAIN_OFFSET_X_H
R m1_main_offset_x[15:0] 0x0000
0x 35 01 M1_MAIN_OFFSET_X_L
0x 35 02 M1_MAIN_OFFSET_Y_H
R m1_main_offset_y[15:0] 0x0000
0x 35 03 M1_MAIN_OFFSET_Y_L
SI 0x 35 04 M1_MAIN_OFFSET_Z_H
R m1_main_offset_z[15:0] 0x0000
SI上位 0x
Ranked 35 05 M1_MAIN_OFFSET_Z_L
データ1
Data 1 0x 35 06 M1_MAIN_T_AVE_H
R m1_main_t_ave[15:0] 0x0000
0x 35 07 M1_MAIN_T_AVE_L
0x 35 08 M1_MAIN_SI_H
R m1_main_si[15:0] 0x0000
0x 35 09 M1_MAIN_SI_L
0x 35 0A M1_MAIN_PGA_H
R m1_main_pga[15:0] 0x0000
0x 35 0B M1_MAIN_PGA_L
SI 0x 36 04 M2_MAIN_OFFSET_Z_H
SI上位 0x
データ2
R m2_main_t_ave[15:0] 0x0000
R m2_main_si[15:0] 0x0000
R m2_main_pga[15:0] 0x0000
0x 37 04 M3_MAIN_OFFSET_Z_H
SI R m3_main_offset_z[15:0] 0x0000
SI上位
Ranked 0x 37 05 M3_MAIN_OFFSET_Z_L
データ3
R m3_main_t_ave[15:0] 0x0000
R m3_main_si[15:0] 0x0000
R m3_main_pga[15:0] 0x0000
ntlp 0x 38 02 M4_MAIN_OFFSET_Y_H
SI上位
SI 0x 38 05 M4_MAIN_OFFSET_Z_L
Ranked
データ4 0x 38 06 M4_MAIN_T_AVE_H
Data 4 0x R m4_main_t_ave[15:0] 0x0000
38 07 M4_MAIN_T_AVE_L
R m4_main_si[15:0] 0x0000
R m4_main_pga[15:0] 0x0000
SI
SI上位 0x
データ5
R m5_main_t_ave[15:0] 0x0000
R m5_main_si[15:0] 0x0000
R m5_main_pga[15:0] 0x0000
No. 9915815-2A (16 /31)
0x 40 00 OFFSET_SET_X_H
R offset_set_x[15:0] 0x0000
0x 40 01 OFFSET_SET_X_L
0x 40 02 OFFSET_SET_Y_H
R offset_set_y[15:0] 0x0000
0x 40 03 OFFSET_SET_Y_L
0x 40 04 OFFSET_SET_Z_H
R offset_set_z[15:0] 0x0000
0x 40 05 OFFSET_SET_Z_L
0x 40 06 OFFSET_SET_T_AVE_H
R offset_set_t_ave[15:0] 0x0000
0x 40 07 OFFSET_SET_T_AVE_L
0x 40 08 OFFSET_SET_MAX_X_H
Initial R offset_set_max_x[15:0] 0x0000
0x 40 09 OFFSET_SET_MAX_X_L
初期設置
Installation
Data 0x 40 0A OFFSET_SET_MAX_Y_H
データ R offset_set_max_y[15:0] 0x0000
0x 40 0B OFFSET_SET_MAX_Y_L
0x 40 0C OFFSET_SET_MAX_Z_H
R offset_set_max_Z[15:0] 0x0000
0x 40 0D OFFSET_SET_MAX_Z_L
0x 40 0E OFFSET_SET_MIN_X_H
R offset_set_min_x[15:0] 0x0000
0x 40 0F OFFSET_SET_MIN_X_L
0x 40 10 OFFSET_SET_MIN_Y_H
R offset_set_min_y[15:0] 0x0000
0x 40 11 OFFSET_SET_MIN_Y_L
0x 40 12 OFFSET_SET_MIN_Z_H
R offset_set_min_Z[15:0] 0x0000
0x 40 13 OFFSET_SET_MIN_Z_L
0x 40 14 OFFSET_SET_AXIS R offset_set_axis[1:0] 0x00
0x 41 00 OFFSET_RECENT_X_H
R offset_recent_x[15:0] 0x0000
0x 41 01 OFFSET_RECENT_X_L
0x 41 02 OFFSET_RECENT_Y_H
R offset_recent_y[15:0] 0x0000
0x 41 03 OFFSET_RECENT_Y_L
0x 41 04 OFFSET_RECENT_Z_H
R offset_recent_z[15:0] 0x0000
0x 41 05 OFFSET_RECENT_Z_L
0x 41 06 OFFSET_RECENT_T_AVE_H
R offset_recent_t_ave[15:0] 0x0000
0x 41 07 OFFSET_RECENT_T_AVE_L
0x 41 08 OFFSET_RECENT_MAX_X_H
R offset_recent_max_x[15:0] 0x0000
Latest 0x 41 09 OFFSET_RECENT_MAX_X_L
Offset 0x
最新オフセッ 41 0A OFFSET_RECENT_MAX_Y_H
R offset_recent_max_y[15:0] 0x0000
Data
トデータ 0x 41 0B OFFSET_RECENT_MAX_Y_L
0x 41 0C OFFSET_RECENT_MAX_Z_H
R offset_recent_max_Z[15:0] 0x0000
0x 41 0D OFFSET_RECENT_MAX_Z_L
0x 41 0E OFFSET_RECENT_MIN_X_H
R offset_recent_min_x[15:0] 0x0000
0x 41 0F OFFSET_RECENT_MIN_X_L
0x 41 10 OFFSET_RECENT_MIN_Y_H
R offset_recent_min_y[15:0] 0x0000
0x 41 11 OFFSET_RECENT_MIN_Y_L
0x 41 12 OFFSET_RECENT_MIN_Z_H
R offset_recent_min_Z[15:0] 0x0000
0x 41 13 OFFSET_RECENT_MIN_Z_L
offset_recent_state[
0x 41 14 OFFSET_RECENT_STATE R 0x00
1:0]
0x 42 00 SELFTEST_BEFORE_X_H
R selftest_before_x[15:0] 0x0000
0x 42 01 SELFTEST_BEFORE_X_L
0x 42 02 SELFTEST_AFTER_X_H
R selftest_after_x[15:0] 0x0000
0x 42 03 SELFTEST_AFTER_X_L
0x 42 04 SELFTEST_BEFORE_Y_H
R selftest_before_y[15:0] 0x0000
0x 42 05 SELFTEST_BEFORE_Y_L
0x 42 06 SELFTEST_AFTER_Y_H
Self-Diag R selftest_after_y[15:0] 0x0000
自己診断
nostic 0x 42 07 SELFTEST_AFTER_Y_L
データ
Data 0x 42 08 SELFTEST_BEFORE_Z_H
R selftest_before_z[15:0] 0x0000
0x 42 09 SELFTEST_BEFORE_Z_L
0x 42 0A SELFTEST_AFTER_Z_H
R selftest_after_z[15:0] 0x0000
0x 42 0B SELFTEST_AFTER_Z_L
0x 42 0C SELFTEST_T_AVE_H
R selftest_t_ave[15:0] 0x0000
0x 42 0D SELFTEST_T_AVE_L
selftest_e
0x 42 0E SELFTEST_ERROR R 0x00
rror
*OMRON assumes no responsibility for operation after accessing registers where access is prohibited.
No. 9915815-2A (17 /31)
(2) Register Details

Basic Settings
Register Data Default
Item
項目レジスタアドレス Register
レジスタ名名称 Name R/W 初期値
0x 10 00 STATE R - - - - - state[2:0] 0x00
Status axis_state
状態 0x 10 01 AXIS_STATE R - - - - - - 0x02
[1:0]
event_off event_sel event_col event_sh
0x 10 02 EVENT R - - - - 0x00
set ftest lapse ut
0x 10 03 MODE R/W - - - - - mode[2:0] 0x01
Change ctrl_thres
設定変更 0x 10 04 CTRL R/W - ctrl_axis[2:0] - - - 0x40
Status h
clear_set clear_rec clear_self clear_qua
0x 10 05 CLEAR_COMMAND R/W - - - - 0x00
_offset ent_offse test ke
0x00: Normal Mode standby

0x01: Normal Mode not in standby
state Current status 0x02: Initial Installation Mode
0x03: Offset Acquisition Mode
0x04: Self-Diagnostic Mode
*You can read the current status with this register.

Normal Mode can be separated into the standby status and not-in-standby status (primarily during
earthquake processing).
0: Use 2 axes YZ
Current axes used for SI value
axis_state 1: Use 2 axes XZ
calculation
2: Use 2 axes XY
*The SI value is calculated from the acceleration values of the two horizontal axes. You can read
information about the two axes that are used in the SI value calculation with this register.
INT1 pin ACTIVE information (shutoff 0: Default

event_shut
signal in earthquake) 1: Shutoff signal ON in earthquake
INT1 pin ACTIVE information (shutoff 0: Default

event_collapse
signal in collapse) 1: Shutoff signal ON in collapse
0: Self-diagnostic OK
event_selftest Self-diagnostic result information
1: Self-diagnostic error
0: Acquire offset OK
event_offset Acquire offset result information
1: Acquire offset error
*When these events occur, the corresponding bit changes to 1.

The bits will change from 1 to 0 when this register is read.
0x01: Normal Mode

0x02: Initial Installation Mode
mode Current mode
0x03: Offset Acquisition Mode
0x04: Self-Diagnostic Mode
*You can read the current mode with this register.

You can also switch the Sensor’s mode by writing that mode to the register.
You can switch to Initial Installation Mode, Offset Acquisition Mode, and Self-Diagnostic Mode only from
Normal Mode.
The mode is restored to Normal Mode after Initial Installation Mode, Offset Acquisition Mode, and
Self-Diagnostic Mode are ended.
Earthquake shutoff judgement threshold 0: Threshold level H

ctrl_thresf
1: Threshold level L
0: YZ axes, 1: XZ axes, 2: XY axes, 3: Auto switch axes (auto axes calculation by automatically
ctrl_axis SI value calculation axes setting pattern switching to Initial Installation Mode at the start of Normal Mode), 4: Switch axes at installation (auto
axes calculation in switching to Initial Installation Mode)
*The earthquake shutoff judgment threshold is active only when using I2C communications (i.e., when the
SELECT pin is high).
The default is threshold level H, and the shutoff signal will be output if an earthquake occurs with a seismic
No. 9915815-2A (18 /31)
intensity equivalent to 5 Upper or higher on the JMA Seismic Intensity Scale.

*You can change the SI value calculation axes setting pattern by writing the corresponding value to
ctrl_axis.
The default is 4: Switch axes at installation. When the Sensor has switched to Initial Installation Mode, the
current tilting of the Sensor is judged and the two axes in the horizontal direction are automatically
calculated to determine the axes to use for the SI value.
With 0: YZ axes, 1: XZ axes, and 2: XY axes, the SI value is calculated with the specified fixed axes.
With 3: Auto switch axes, the current tilting of the Sensor is judged and the two axes in the horizontal
direction are automatically calculated to determine the axes to use for the SI value each time the power
supply is turned ON or Normal Mode is started.
0: Default
clear_quake Clear earthquake data memory
1: Start clear earthquake data memory
0: Default
clear_selftest Clear self-diagnostic data memory
1: Start clear self-diagnostic data memory
clear_recent 0: Default
Clear latest offset data memor
_offset 1: Start clear latest offset data memory
clear_set_off 0: Default
Clear initial installation data memory
set 1: Start clear initial installation data memory
*Change the corresponding bit from 0 to 1 to clear the corresponding memory (the data will be written with
zeros). Earthquake data is located in register addresses 0x3000 to 0x391D. Self-diagnostic data is located
in register addresses 0x4200 to 0x420E. Latest offset data is located in registered addresses 0x4100 to
0x4114. Initial installation data is located in register addresses 0x4000 to 0x4014.
Earthquake-Related Data (During an Earthquake)

During an earthquake, you can acquire the SI value and PGA currently being calculated by executing a
read on the following register addresses.

項目レジスタアドレスレジスタ名名称 R/W 初期値
Earthquake- 0x 20 00 MAIN_SI_H
地震関連
Related R main_si[15:0] 0x0000
0x 20 01 MAIN_SI_L
データ
Data (During
(地震中)
an 0x 20 02 MAIN_PGA_H
R main_pga[15:0] 0x0000
Earthquake) 0x 20 03 MAIN_PGA_L
0x0000 to 0xFFFF (0.0 to 6,553.5)

main_si SI value
*Precision fixed to one digit after the decimal point.
*The SI value during an earthquake. The value becomes 0 when the earthquake ends.
0x0000 to 0xFFFF (0 to 65,535)

main_pga PGA (2-axis synthetic peak acceleration)
*Integer
*The PGA value during an earthquake. The value becomes 0 when the earthquake ends.
No. 9915815-2A (19 /31)
Earthquake-Related Data (Latest Data)

After the earthquake ends, you can read the data for the past five earthquakes by accessing the following
register addresses via I2C. Latest Data 1 (register addresses 0x3000 to 0x300B) always holds the latest
data.
Item
最新データ1
R n1_main_t_ave[15:0] 0x0000
R n1_main_si[15:0] 0x0000
R n1_main_pga[15:0] 0x0000
Latest 0x 31 05 N2_MAIN_OFFSET_Z_L
最新データ2
Data 2
R n2_main_t_ave[15:0] 0x0000
R n2_main_si[15:0] 0x0000
R n2_main_pga[15:0] 0x0000
Latest
最新データ3
R n3_main_t_ave[15:0] 0x0000
R n3_main_si[15:0] 0x0000
R n3_main_pga[15:0] 0x0000
最新データ4
R n4_main_t_ave[15:0] 0x0000
R n4_main_si[15:0] 0x0000
R n4_main_pga[15:0] 0x0000
最新データ5
R n5_main_t_ave[15:0] 0x0000
R n5_main_si[15:0] 0x0000
R n5_main_pga[15:0] 0x0000
No. 9915815-2A (20 /31)
n1_main_offset_x 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

X-axis acceleration offset gal
to n5_main_offset_x *Precision fixed to one digit after the decimal point.
*X-axis acceleration offset value that was used when calculating the saved SI value and PGA.
The newest value is n1 and the oldest value is n5.
n1_main_offset_y 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

Y-axis acceleration offset gal
to n5_main_offset_y *Precision fixed to one digit after the decimal point.
*Y-axis acceleration offset value that was used when calculating the saved SI value and PGA.
n1_main_offset_z 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

Z-axis acceleration offset gal
to n5_main_offset_z *Precision fixed to one digit after the decimal point.
*Z-axis acceleration offset value that was used when calculating the saved SI value and PGA.
n1_main_t_ave Temperature during SI 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

C
to n5_main_t_ave calculation *Precision fixed to one digit after the decimal point.
*Temperature during calculation of the saved SI value and PGA.

n1_main_si 0x0000 to 0xFFFF (0.0 to 6,553.5)

SI value kine
to n5_main_si *Precision fixed to one digit after the decimal point.
*SI values stored in order from newest to oldest.

n1_main_pga PGA (2-axis synthetic peak 0x0000 to 0xFFFF (0.0 to 6,553.5)

gal
to n5_main_pga acceleration) *Precision fixed to one digit after the decimal point.
*PGA stored in order from newest to oldest.

No. 9915815-2A (21 /31)
Earthquake-Related Data (SI Ranked Data)

After the earthquake ends, you can read the data for five earthquakes with the largest SI values, out of all
earthquakes that occurred in the past, by accessing the following register addresses via I2C. SI Ranked
Data 1 (register addresses 0x3500 to 0x350B) always holds the largest SI value.
Item
SI
SI上位
Ranked 0x 35 05 M1_MAIN_OFFSET_Z_L
データ1
R m1_main_t_ave[15:0] 0x0000
R m1_main_si[15:0] 0x0000
R m1_main_pga[15:0] 0x0000
SI上位
Ranked
0x 36 05 M2_MAIN_OFFSET_Z_L
データ2
R m2_main_t_ave[15:0] 0x0000
R m2_main_si[15:0] 0x0000
R m2_main_pga[15:0] 0x0000
SI上位 0x 37 05 M3_MAIN_OFFSET_Z_L
Ranked
データ3
R m3_main_t_ave[15:0] 0x0000
R m3_main_si[15:0] 0x0000
R m3_main_pga[15:0] 0x0000
SI上位 0x 38 05 M4_MAIN_OFFSET_Z_L
Ranked
データ4 0x 38 06 M4_MAIN_T_AVE_H
Data 4 R m4_main_t_ave[15:0] 0x0000
R m4_main_si[15:0] 0x0000
R m4_main_pga[15:0] 0x0000
SI上位
Ranked
0x 39 05 M5_MAIN_OFFSET_Z_L
データ5
R m5_main_t_ave[15:0] 0x0000
R m5_main_si[15:0] 0x0000
R m5_main_pga[15:0] 0x0000
No. 9915815-2A (22 /31)
m1_main_offset_x 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

X-axis acceleration offset gal
to m5_main_offset_x *Precision fixed to one digit after the decimal point.
*X-axis acceleration offset value that was used when calculating the saved SI value and PGA.
The largest SI value during an earthquake is m1, followed by m2, m3, m4, and m5 in descending order.
m1_main_offset_y 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

Y-axis acceleration offset gal
to m5_main_offset_y *Precision fixed to one digit after the decimal point.
*Y-axis acceleration offset value that was used when calculating the saved SI value and PGA.
m1_main_offset_z 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

Z-axis acceleration offset gal
to m5_main_offset_z *Precision fixed to one digit after the decimal point.
*Z-axis acceleration offset value that was used when calculating the saved SI value and PGA.
m1_main_t_ave Temperature during SI 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

C
to m5_main_t_ave calculation *Precision fixed to one digit after the decimal point.
*Temperature during calculation of the saved SI value and PGA.

m1_main_si 0x0000 to 0xFFFF (0.0 to 6,553.5)

SI value kine
to m5_main_si *Precision fixed to one digit after the decimal point.
*SI values stored in order from the largest value.

m1_main_pga PGA (2-axis synthetic peak 0x0000 to 0xFFFF (0.0 to 6,553.5)

gal
to m5_main_pag acceleration) *Precision fixed to one digit after the decimal point.
* *PGA values stored in order from the largest SI value.

Initial Installation Data

項目
Item レジスタアドレスレジスタ名名称
Register Name R/W 初期値
0x 40 00 OFFSET_SET_X_H
R offset_set_x[15:0] 0x0000
0x 40 01 OFFSET_SET_X_L
0x 40 02 OFFSET_SET_Y_H
R offset_set_y[15:0] 0x0000
0x 40 03 OFFSET_SET_Y_L
0x 40 04 OFFSET_SET_Z_H
R offset_set_z[15:0] 0x0000
0x 40 05 OFFSET_SET_Z_L
0x 40 06 OFFSET_SET_T_AVE_H
R offset_set_t_ave[15:0] 0x0000
0x 40 07 OFFSET_SET_T_AVE_L
0x 40 08 OFFSET_SET_MAX_X_H
R offset_set_max_x[15:0] 0x0000
Initial 0x 40 09 OFFSET_SET_MAX_X_L
初期設置
Installtion 0x 40 0A OFFSET_SET_MAX_Y_H
データ
Data R offset_set_max_y[15:0] 0x0000
0x 40 0B OFFSET_SET_MAX_Y_L
0x 40 0C OFFSET_SET_MAX_Z_H
R offset_set_max_Z[15:0] 0x0000
0x 40 0D OFFSET_SET_MAX_Z_L
0x 40 0E OFFSET_SET_MIN_X_H
R offset_set_min_x[15:0] 0x0000
0x 40 0F OFFSET_SET_MIN_X_L
0x 40 10 OFFSET_SET_MIN_Y_H
R offset_set_min_y[15:0] 0x0000
0x 40 11 OFFSET_SET_MIN_Y_L
0x 40 12 OFFSET_SET_MIN_Z_H
R offset_set_min_Z[15:0] 0x0000
0x 40 13 OFFSET_SET_MIN_Z_L
0x 40 14 OFFSET_SET_AXIS R offset_set_axis[1:0] 0x00
No. 9915815-2A (23 /31)
X-axis acceleration offset 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_x gal
*X-axis acceleration offset value during initial installation.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_y Y-axis acceleration offset gal
*Y-axis acceleration offset value during initial installation.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_z Z-axis acceleration offset gal
*Z-axis acceleration offset value during initial installation.
Temperature during initial 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_ave C
installation *Precision fixed to one digit after the decimal point.
*Temperature during initial installation.
Maximum value of X-axis 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_max_x acceleration when the offset *Precision fixed to one digit after the decimal point. gal
values were acquired
*Maximum value of X-axis acceleration when calculating the offset during initial installation.
Maximum value of Y-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_set_max_y acceleration when the offset gal
*Maximum value of Y-axis acceleration when calculating the offset during initial installation.
Maximum value of Z-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_set_max_z acceleration when the offset gal
*Maximum value of Z-axis acceleration when calculating the offset during initial installation.
Minimum value of X-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_set_min_x acceleration when the offset gal
*Minimum value of X-axis acceleration when calculating the offset during initial installation.
Minimum value of Y-axis 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_min_y acceleration when the offset *Precision fixed to one digit after the decimal point. gal
*Minimum value of Y-axis acceleration when calculating the offset during initial installation.
Minimum value of Z-axis 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_set_min_z acceleration when the offset *Precision fixed to one digit after the decimal point. gal
*Minimum value of Z-axis acceleration when calculating the offset during initial installation.
0: Use 2 axes YZ
Axes information during initial
offset_set_axis 1: Use 2 axes XZ
installation
2: Use 2 axes XY
*Information about the axes that were decided during initial installation and will be used in the SI value calculation.
No. 9915815-2A (24 /31)
Latest Offset Data

Item
0x 41 00 OFFSET_RECENT_X_H
R offset_recent_x[15:0] 0x0000
0x 41 01 OFFSET_RECENT_X_L
0x 41 02 OFFSET_RECENT_Y_H
R offset_recent_y[15:0] 0x0000
0x 41 03 OFFSET_RECENT_Y_L
0x 41 04 OFFSET_RECENT_Z_H
R offset_recent_z[15:0] 0x0000
0x 41 05 OFFSET_RECENT_Z_L
0x 41 06 OFFSET_RECENT_T_AVE_H
R offset_recent_t_ave[15:0] 0x0000
0x 41 07 OFFSET_RECENT_T_AVE_L
Latest 0x 41 08 OFFSET_RECENT_MAX_X_H
R offset_recent_max_x[15:0] 0x0000
Offset 0x 41 09 OFFSET_RECENT_MAX_X_L
最新オフセッ
Data 0x 41 0A OFFSET_RECENT_MAX_Y_H
トデータ R offset_recent_max_y[15:0] 0x0000
0x 41 0B OFFSET_RECENT_MAX_Y_L
0x 41 0C OFFSET_RECENT_MAX_Z_H
R offset_recent_max_Z[15:0] 0x0000
0x 41 0D OFFSET_RECENT_MAX_Z_L
0x 41 0E OFFSET_RECENT_MIN_X_H
R offset_recent_min_x[15:0] 0x0000
0x 41 0F OFFSET_RECENT_MIN_X_L
0x 41 10 OFFSET_RECENT_MIN_Y_H
R offset_recent_min_y[15:0] 0x0000
0x 41 11 OFFSET_RECENT_MIN_Y_L
0x 41 12 OFFSET_RECENT_MIN_Z_H
R offset_recent_min_Z[15:0] 0x0000
0x 41 13 OFFSET_RECENT_MIN_Z_L
0x 41 14 OFFSET_RECENT_STATE R offset_recent_state[ 0x00
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_recent_x X-axis acceleration offset gal
*Current X-axis acceleration offset value.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_recent_y Y-axis acceleration offset gal
*Current Y-axis acceleration offset value.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_recent_z Z-axis acceleration offset gal
*Current Z-axis acceleration offset value.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

offset_recent_ave Latest temperature C
*Temperature when the current offset values were calculated.
Maximum value of X-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_max_x acceleration when the offset gal
*Maximum value of X-axis acceleration when the current offset values were calculated.
Maximum value of Y-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_max_y acceleration when the offset gal
*Maximum value of Y-axis acceleration when the current offset values were calculated.
Maximum value of Z-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_max_z acceleration when the offset gal
*Maximum value of Z-axis acceleration when the current offset values were calculated.
Minimum value of X-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_min_x acceleration when the offset gal
*Minimum value of X-axis acceleration when the current offset values were calculated.
No. 9915815-2A (25 /31)
Minimum value of Y-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_min_y acceleration when the offset gal
*Minimum value of Y-axis acceleration when the current offset values were calculated.
Minimum value of Z-axis

0x8000 to 0x7FFF (-3,276.8 to 3,276.7)
offset_recent_min_z acceleration when the offset gal
*Minimum value of Z-axis acceleration when the current offset values were calculated.
0: Offset during earthquake judgment in Normal Mode

offset_recent_state Offset data type 1: Offset from Initial Installation Mode
2: Offset from Offset Acquisition Mode
*Information about the mode used to acquire the offset values when the current offset values were calculated.
Self-Diagnostic Data
項目レジスタアドレス
Address レジスタ名名称 R/W 初期値
Value
bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
0x 42 00 SELFTEST_BEFORE_X_H
R selftest_before_x[15:0] 0x0000
0x 42 01 SELFTEST_BEFORE_X_L
0x 42 02 SELFTEST_AFTER_X_H
R selftest_after_x[15:0] 0x0000
0x 42 03 SELFTEST_AFTER_X_L
0x 42 04 SELFTEST_BEFORE_Y_H
R selftest_before_y[15:0] 0x0000
0x 42 05 SELFTEST_BEFORE_Y_L
0x 42 06 SELFTEST_AFTER_Y_H
Self-Diag R selftest_after_y[15:0] 0x0000
自己診断 0x 42 07 SELFTEST_AFTER_Y_L
nostic
データ
Dada 0x 42 08 SELFTEST_BEFORE_Z_H
R selftest_before_z[15:0] 0x0000
0x 42 09 SELFTEST_BEFORE_Z_L
0x 42 0A SELFTEST_AFTER_Z_H
R selftest_after_z[15:0] 0x0000
0x 42 0B SELFTEST_AFTER_Z_L
0x 42 0C SELFTEST_T_AVE_H
R selftest_t_ave[15:0] 0x0000
0x 42 0D SELFTEST_T_AVE_L
selftest_e
0x 42 0E SELFTEST_ERROR R 0x00
rror
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_before_x X-axis reference acceleration gal
*X-axis acceleration before the self-diagnostic was run.
X-axis self-diagnostic 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_after_x gal
acceleration *Precision fixed to one digit after the decimal point.
*X-axis acceleration after the self-diagnostic was run.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_before_y Y-axis reference acceleration gal
*Y-axis acceleration before the self-diagnostic was run.
Y-axis self-diagnostic 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_after_y gal
*Y-axis acceleration after the self-diagnostic was run.
0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_before_z Z-axis reference acceleration gal
*Z-axis acceleration before the self-diagnostic was run.
Z-axis self-diagnostic 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_after_z gal
*Z-axis acceleration after the self-diagnostic was run.
Temperature during 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

selftest_t_ave C
self-diagnostic *Precision fixed to one digit after the decimal point.
*Temperature during self-diagnostic.

No. 9915815-2A (26 /31)
0: Self-diagnostic OK
selftest_error Self-diagnostic result
1: Self-diagnostic error
*The result of the self-diagnostic.
14. Environmental Performance
(1) Low Temperature Exposure

The characteristics in Section 9 are met after the Sensor was exposed to an
environment of -40 3 C in a constant temperature chamber for 72 hours.
(2）High Temperature Exposure
environment of 80 3 C in a constant temperature chamber for 96 hours.
(3）High Temperature & Humidity Exposure
environment of 40 2 C and 90% to 95% in a constant temperature chamber for
96 hours.
(4) Drop Resistance
The characteristics in Section 9 are met after the Sensor was freely dropped three
times on a concrete surface from a height of 1 m.
(5) Vibration Endurance
The characteristics in Section 9 are met after the Sensor was exposed to
vibrations with a frequency of 10 Hz to 55 Hz, total amplitude of 1.5 mm, and
sweeping in the X, Y, and Z directions for two hours for each axis.
(6) Electrostatic Resistance
HBM: 1.5 kΩ and 100 pF, no abnormalities with an electrostatic discharge of 2
kV.
MM: 0 kΩ and 200 pF, no abnormalities with an electrostatic discharge of 200 V.
Note: After the test ends, the Sensor is measured after it is exposed to ambient temperature and humidity for
two hours.
No. 9915815-2A (27 /31)
15. Shipped Form
The product is stored on a φ330 reel which stores 1,000 units.

The following diagram shows the appearance of the reel and label.
Label
Tape Unwiding Direction
The following diagram shows the detailed dimensions of the carrier tape.
through hole
No. 9915815-2A (28 /31)
16. Handling Precautions
(1) Handling the Product

1) Do not use the Sensor in locations with volatile, flammable, or corrosive gas (organic solvent vapor, sulfite
gas, chlorine, sulfide gas, ammonia gas, etc.) or other toxic gases. They may cause the Sensor to break
down.）
2) Do not use the Sensor in locations subject to fresh water, salt water, water drops, or splattering oil.
3) Do not use the Sensor in an environment where condensation or icing may occur. Moisture freezing on the
Sensor may cause output to fluctuate or may cause the Sensor to break down.
4) Do not use the Sensor in locations subject to direct sunlight. Doing so may cause the Sensor to break
down.
5) Do not use the Sensor in locations subject to direct radiant heat from heating equipment. Doing so may
cause the Sensor to break down.
6) Do not use the Sensor in locations with severe temperature changes. Doing so may cause the Sensor to
break down.
7) Do not use the Sensor in environments with excess mechanical stress. Doing so may cause the Sensor to
malfunction or break down.
8) Do not use the Sensor in locations with large vibration or shock. These may cause the Sensor to break
down.
9) Do not use the Sensor in locations with strong electrical or magnetic fields. These may cause the Sensor to
break down.
10) Static electricity can destroy the Sensor. Take countermeasures including grounded work benches, floors,
and other charged objects and workers.
11) This Sensor is a precision device. Do not drop it or subject it to excessive shock or force. Doing so could
break it or change its characteristics. Do not use the Sensor if it has been dropped.
12) Do not handle the Sensor in locations with excessive vapor, dust, dirt, etc.
13) Do not hold the Sensor with pliers, tweezers, or similar tools, and do not subject components to damage or
excessive shock due to inadequate adjustment of the mounter.
14) When placing components near the edge of the PCB or near a connector, make sure that stress is not
applied to the Sensor when the device is assembled or when the connector is connected or disconnected.
15) Do not apply any external force to components after soldering until everything has cooled off and do not
allow mechanical stress due to PCB warping or other factors.
16) Under some usage conditions, ultrasound may cause the Sensor to resonate and be destroyed. OMRON
cannot specify the detailed conditions under which the Sensor will be used, so we assume no responsibility
if the Sensor is used in environments where ultrasound is used. If the Sensor must be used in an
environment with ultrasound, check its performance in the actual environment beforehand.
17) The Sensor does not contain any protective circuits. Never allow the electrical load to exceed the absolute
maximum ratings. Such loads may damage the circuits. If required, install protective circuits so that absolute
maximum ratings are not exceeded.
18) Allow as much space as possible between the Sensor and devices that generate surges or high
frequencies (such as high-frequency welders and high-frequency sewing machines). Attach a surge
protector or noise filter on nearby noise-generating devices (in particular, motors, transformers, solenoids,
No. 9915815-2A (29 /31)
magnetic coils, or other devices that have an inductance component).

19) Wire the Sensor away from high-voltage and large-current power lines in order to prevent inductance noise.
It is also helpful to separate conduits and ducts and to use shielded cables.
20) When using a switching regulator, power supply switching noise may cause malfunctions, so check this
before use.
21) Stress due to plastic hardening may change Sensor characteristics. Do not mold seal the Sensor after
mounting.
22) When applying a moisture preventing coating or other coating after mounting the Sensor, select a coating
with minimal stress and check operation carefully.
23) Do not attempt to disassemble or modify the Sensor.
24) Do not use the Sensor in safety devices or for applications in which Sensor operation would directly affect
human life.
25) Carefully read the precaution in the Instruction Manual before using the Sensor.
26) In addition, if you use the Sensor under conditions other than those in these specifications, check Sensor
operation under those conditions beforehand.
(2) Transportation and Storage
27) Do not store the Sensor in locations with harmful corrosive gas (organic solvent vapor, sulfite gas, sulfide
gas, etc.)
28) The Sensor is not drip proof, so do not store it anywhere that water might get on it.
29) Store the Sensor within appropriate temperature and humidity ranges.
30) Note: Before storing the Sensor in an environment other than the environment recommended by OMRON,
evaluate the results in the actual storage environment and judge whether or not storage there is
appropriate.
31) Do not store the Sensor in locations with excessive vapor, dust, dirt, etc.
(3) Measures for Product Failures

32) If a failure occurs where the Sensor does not meet these specifications in the receiving inspection at your
factory after delivery, and the cause of the failure lies with OMRON, a replacement product will be provided
at no charge. In this situation, the Sensors that have been judged as defective will be returned to OMRON.
33) If a failure occurs after your receiving inspection, measures for those Sensors may be decided after
negotiations by both parties. As a general rule, Sensors that are rejected from receiving are to be returned
to OMRON within 14 days of the receiving date after clearly specifying the details of the failure.
17.Conditions of Use
(4) The definition of terms used in item 17 are as follows:
1) Usage conditions: Usage conditions, rating, performance, operating environment, handling instructions,
cautions, prohibited use, etc. of the Vibration Sensors described in the documents such as these Product
Specifications, instruction sheets, or user’s manuals.
2) Customer application: Application of the Vibration Sensors by customers which include embedding and/or
using the Vibration Sensors in their parts/components, electronic substrates, devices, equipment or
systems manufactured by customers.
3) Fitness: (a) fitness, (b) performance, (c) non-infringement of third-party intellectual property, (d) compliance
No. 9915815-2A (30 /31)
with laws and regulations and (e) conformity to standards.
(5) Caution on Descriptions

Attention is required to the following points on descriptions in these Product Specifications.
1) Rated values and performance values are the product of tests performed for separate single conditions,
including but not limited to temperature and humidity. It is not intended to warrant rated values and
performance values for multiple combined conditions.
2) Reference data are provided for reference only. Omron does NOT warrant that the Vibration Sensors work
properly at all time in the range of reference data.
3) Application examples are provided for reference only. Omron does NOT warrant the fitness of the Vibration
Sensors under such application.
4) Omron may discontinue the production of the Vibration Sensors or change the specifications of them for
the purpose of improving such products or other reasons entirely at its own discretion.
(6) Please be aware of and accept the following when you introduce or use the Vibration Sensors:
34) Please use the Vibration Sensors in compliance with usage conditions including rating and performance.
35) Please confirm fitness of the Vibration Sensors in your application and use your own judgment to determine
the appropriateness of using them in such application. Omron shall not warrant the fitness of the Vibration
Sensors in customer application.
36) Please confirm that the Vibration Sensors are properly wired and installed for their intended use in your
overall system.
37) When using the Vibration Sensors, please make sure to (i) maintain a margin of safety vis- -vis the
published rated and performance values, (ii) design to minimize risks to customer application in case of
failure of the Vibration Sensors, such as introducing redundancy, (iii) introduce system-wide safety
measures to notify risks to users, and (iv) conduct regular maintenance on the Vibration Sensors and
customer application.
38) The Vibration Sensors are designed and manufactured as general-purpose products for use in general
industrial products. They are not intended to be used in the following applications. If you are using the
Vibration Sensors in the following applications, Omron shall not provide any warranty for such Vibration
Sensors. Even in the case of the following applications to elevator/lift equipment and medical devices, etc,
some case are likely applied to an usual guarantee prescribed on next article as general-purpose products
used for general industrial products. So, please contact our sales person in charge.
(a) Applications with stringent safety requirements, including but not limited to nuclear power control
equipment, combustion equipment, aerospace equipment, railway equipment, elevator/lift equipment,
amusement park equipment, medical equipment, safety devices and other applications that could
cause danger/harm to people body and life.
(b) Applications that require high reliability, including but not limited to supply systems for gas, water and
electricity, etc., 24 hour continuous operating systems, financial settlement systems and other
applications that handle rights and property.
(c) Applications under severe conditions or in severe environment, including but not limited to outdoor
equipment, equipment exposed to chemical contamination, equipment exposed to electromagnetic
interference and equipment exposed to vibration and shocks.
No. 9915815-2A (31 /31)
(d) Applications under conditions and environment not described in these Product Specifications.
39) In addition to the applications listed in (a) to (d) above, the Vibration Sensors are not intended for use in
automotive applications (including two wheeled vehicles). Please do NOT use the Vibration Sensors for
automotive applications. Please contact Omron sales staff for products for automotive use.
(7) The terms and conditions for warranty of the Vibration Sensors are as follows:
1) Warranty period: One year after the purchase.
2) Coverage: Free replacement of the malfunctioning Vibration Sensors with the same number of
replacement/alternative products.
3) Exceptions: Omron will not cover the Vibration Sensors under its warranty if the cause of the
malfunction falls under any of the following:
(a) Usage in a manner other than the original intended use for the Vibration Sensors.
(b) Usage outside of the usage conditions.
(c) Modification or repair made to the Vibration Sensors by other than Omron personnel.
(d) Software program embedded by other than Omron or usage of such software.
(e) Causes which could not have been foreseen with the level of science and technology at the time of
shipping from Omron.
(f) Causes originating from other than Omron or the Vibration Sensors (including force majeure such
as but not limited to natural disasters).
(8) Limitation of Liability

The warranty set out in these Terms and Conditions is the whole and sole liability for the Vibration Sensors.
There are no other warranties, expressed or implied. Omron and the distributors of the Vibration Sensors are
not liable for any damages which may arise from or be related to the Vibration Sensors.
(9) Export Controls

Customers of the Vibration Sensors shall comply with all applicable laws and regulations of Japan and/or other
relevant countries with regard to security export control, when exporting the Vibration Sensors and/or technical
documents or providing such products and/or documents to a non-resident.
Omron may not provide customers with the Vibration Sensors and/or technical documents should they fail to
comply with such laws and regulations.
A 161116 First version K.Fujiwara S.Fukui

Symbol Date Revised Content Issued By Checked By Approved By

D7S

Uploaded by

Copyright:

Available Formats

D7S

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

D7S

Uploaded by

Copyright:

Available Formats

No.

Issued By Checked By Approved By

Registration Part Number for Customer

Receipt Stamp (For Receipt Purpose Only) Submitted Stamp

Item Name: Vibration Sensor

4) Terminal Arrangement (Top View):

Signal Function Direction Description

6. Recommended Circuit Diagram

7. Recommended Mounting Pattern

Recommended Mounting Conditions

Recommended Land Pattern

(2) Electrical Characteristics

(4) Environmental Performance

9. Sensor Characteristics (Vcc = 3.0 V and Ta = 25 C unless otherwise specified.)

10. Operation Overview

The Sensor has the following functions.

1) Shutoff Signal Output Function

2) Collapse Detection Function

3) Information Acquisition Function via I2C Communications

11. Operation Mode Details

(2) Normal Mode

(3) Initial Installation Mode

Auto Judge Axes

Store Used Axes

(4) Offset Acquisition Mode

(5) Self-Diagnostic Mode

12. I2C Communications Protocol

Device Type Slave

The I2C slave address (0x55) is expressed as follows.

Bit bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

(1) Single Write Access Protocol

(2) Multi Write Access Protocol

(3) Single Read Access Protocol

(4) Multi Read Access Protocol

13. Implemented Registers

Item Register Register Name Data Default

0x 10 00 STATE R - - - - - state[2:0] 0x00

0x 10 03 MODE R/W - - - - - mode[2:0] 0x01

(2) Register Details

0x 10 00 STATE R - - - - - state[2:0] 0x00

0x 10 03 MODE R/W - - - - - mode[2:0] 0x01

0x00: Normal Mode standby

*You can read the current status with this register.

INT1 pin ACTIVE information (shutoff 0: Default

INT1 pin ACTIVE information (shutoff 0: Default

*When these events occur, the corresponding bit changes to 1.

0x01: Normal Mode

*You can read the current mode with this register.

Earthquake shutoff judgement threshold 0: Threshold level H

intensity equivalent to 5 Upper or higher on the JMA Seismic Intensity Scale.

Earthquake-Related Data (During an Earthquake)

Item Register Register Name Data Default

0x0000 to 0xFFFF (0.0 to 6,553.5)

0x0000 to 0xFFFF (0 to 65,535)

Earthquake-Related Data (Latest Data)

n1_main_offset_x 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

n1_main_offset_y 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

n1_main_offset_z 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)

n1_main_t_ave Temperature during SI 0x8000 to 0x7FFF (-3,276.8 to 3,276.7)