Chemical Composition of Materials

KRUPP INDUSTRIES INDIA LTD.
Design & MATERIAL REFERENCE MANUAL G.L. No.:1600-8

Engineering Date: 10/11/98
Division 1. SCOPE AND PURPOSE Rev. 0
Table of contents
Sr. No. DESCRIPTION
1 Scope and purpose

2 Heat treatment
3 Testing
4 Grades and equivalents
5 Properties
6 Application
1 SCOPE & PURPOSE :
1.1 This manual covers the following types of materials:
Low Carbon Structural steels

Rolled / Forged steels
Cast steels
Cast Irons
Stainless steels
High Temperature steels
Spring steels
Case Hardening Steels
Non - Ferrous castings
412704185.xls 1 OF 155
1.2 Sr. N0. 4 ( Grades and equivalent )of the manual furnishes nearest equivalents, wherever possible, from various
international standards. However these equivalents shall be used only after detail study with respect to the application
requirements.
1.3 Sr. No.5 ( Properties ) provides a ready reference for the chemical and mechanical properties of the above stated materials.
The mechanical properties mentioned here comply to a certain type of heat treatment (Supply Condition ) and a range of product thickness /
diameter (LRS). Please refer to the relevant standard for mechanical properties in any other heat treatment condition
and / or thickness / diameter.
1.4 The manual enlists typical applications of different grades only for information purposes in Sr. No. 6.(Application )
1.5 This manual shall in no case act as a substitute for Specifications & shall not be used for Ordering of materials.
1.6 The material grades and standards in shaded cells are OBSOLETE and are only for reference.
2 HEAT TREATMENT :
2.1 Heat treatments generally suggested by standards for the above steels and irons are mentioned in the manual Sr. No. 6.
However in special cases appropriate heat treatment can be suggested while ordering to achieve higher or lower mechanical
properties than those mentioned.
3 TESTING :
3.1 Specific testing requirements like Radiography, Ultrasonic testing etc. shall be specified based on requirements of the application.
NOTE : The KM numbers mentioned herein are standard identification numbers maintained across all sections of the manual for locating any material.
412704185.xls 2 OF 155
List of standards covered in the Materials Manual.
ASTM-A-27M - 95 DIN 1681 - 85 IS 25 - 79

ASTM-A-36M - 96 DIN 1691 - 85 IS 210 - 93
ASTM-A-47M - 90 DIN 1692 - 82 IS 276 - 92
ASTM-A-48M - 94 DIN 1693 - 73 IS 305 - 81
ASTM-A-106 - 97a DIN 1705 - 81 IS 306 - 83
ASTM-A-108 - 95 DIN 1709 - 81 IS 318 - 81
ASTM-A-128M - 93 DIN 1714 - 81 IS 513 - 86
ASTM-A-148M - 93b DIN 17100 - 80 IS 1030 - 89
ASTM-A-213M - 95a DIN 17102 - 83 IS 1079 - 73
ASTM-A-216M - 93 DIN 17155 - 83 IS 1570-1 - 78
ASTM-A-220M - 93 DIN 17175 - 79 IS 1570-2 - 79
ASTM-A-240M - 96a DIN 17182 - 92 IS 1865 - 91
ASTM-A-283M - 93a DIN 17200 - 87 IS 1875 - 92
ASTM-A-285M - 90 DIN 17205 - 92 IS 2002 - 92
ASTM-A-297M - 93 DIN 17210 - 86 IS 2062 - 92
ASTM-A-299M - 90 DIN 17221 - 90 IS 2107 - 77
ASTM-A-322 - 91 DIN 17222 - 79 IS 2507 - 75
ASTM-A-351M - 94a DIN 17245 - 87 IS 2644 - 94
ASTM-A-366M - 96 DIN 17350 - 80 IS 2707 - 89
ASTM-A-387M - 92 DIN 17440 - 85 IS 2708 - 93
ASTM-A-515M - 92 DIN 17465 - 93 IS 2856 - 87
ASTM-A-516M - 90 IS 4522 - 86
ASTM-A-536M - 93 EN 1561 - 97
ASTM-A-569M - 97 EN 1562 - 97 BS 970-1 - 96
ASTM-A-573M - 93a EN 1563 - 97 BS 970-2 - 88
ASTM-A-612M - 90 EN 10025 - 93 BS 1400 - 85
EN 10028-2 - 93 BS 1501-1 - 80
SEW 028 - 93 EN 10028-3 - 93 BS 3059-1 - 87
SEW 390 - 91 EN 10083 - 96 BS 3059-2 - 90
SEW 835 - 97 EN 10084 - 96 BS 3602-1 - 87
412704185.xls 3 OF 155
EN 10088 - 95 BS 3602-2 - 91
EN 10113-2 - 95
EN 10213 - 96
412704185.xls 4 OF 155
Division 4. GRADES AND EQUIVALENTS Rev. 0
MATL NO STANDARD GRADE GERMAN NEAREST EQUIVALENT GRADES AND STANDARDS REMARKS
DESIGNATION MATL NO IS DIN EN BS ASTM
4.1 LOW CARBON STRUCTURAL STEELS
IS 2062 Steel for General Structural Purposes

Gr A IS 1570-1 Fe 410 , DIN 17100 EN 10025 - S235JR,
KM 101 IS 2062 Fe 410W A IS 1079 - St 42 St 37-2, St 44-2 S275JR Weldable quality
Gr B IS 1570-1 Fe 410 , DIN 17100 EN 10025 - S235J0,
KM 102 IS 2062 Fe 410W B IS 1079 - St 42 St 37-2U, St 44-2U S275J0 Weldable quality
Gr C IS 1570-1 Fe 410 , DIN 17100 EN 10025-S235J2G3 Weldable quality with very
KM 103 IS 2062 Fe 410W C IS 1079 - St 42 St 37-3N , St 44-3N , S275J2G3 good impact properties
IS 1570-1 Schedules for wrought steels specified by Tensile or Yield Strength properties.
KM 104 IS 1570-1 Fe 290
KM 105 IS 1570-1 FeE 220
KM 106 IS 1570-1 Fe 310
KM 107 IS 1570-1 FeE 230
KM 108 IS 1570-1 Fe 330 IS 1079 St 34 DIN 17100 St 33 EN 10025 - S185
KM 109 IS 1570-1 FeE 250
KM 110 IS 1570-1 Fe 360 DIN 17100 St 37-2 EN 10025-S235JR
KM 111 IS 1570-1 FeE 270
IS 1079 St 42,
KM 112 IS 1570-1 Fe 410 IS 2062 Gr A DIN 17100 St 44-2 EN 10025-S275JR
KM 113 IS 1570-1 FeE 310
KM 114 IS 1570-1 Fe 490 IS 1079 St 50 DIN 17100 St 50-2 EN 10025-E295
KM 115 IS 1570-1 FeE 370
KM 116 IS 1570-1 Fe 540
KM 117 IS 1570-1 FeE 400
KM 118 IS 1570-1 Fe 620 DIN 17100 St 60-2 EN 10025-E335
KM 119 IS 1570-1 FeE 460
KM 120 IS 1570-1 Fe 690 DIN 17100 St 70-2 EN 10025-E360
412704185.xls 5 OF 155
KM 121 IS 1570-1 FeE 520
KM 122 IS 1570-1 Fe 770
KM 123 IS 1570-1 FeE 580
KM 124 IS 1570-1 Fe 870
KM 125 IS 1570-1 FeE 650
IS 1079 Hot rolled carbon steel sheets & strips

KM 126 IS 1079 Gr O Ordinary quality
KM 127 IS 1079 Gr D Drawing quality
KM 128 IS 1079 Gr DD Deep Drawing quality
KM 129 IS 1079 Gr EDD Extra Deep Drawing Quality
KM 130 IS 1079 Gr St 34 IS 1570-1 Fe 330 DIN 17100 St 33 EN 10025 S185
IS 2062 - Gr A,B, IS EN 10025 S275JR,
KM 131 IS 1079 Gr St 42 1570-1 Fe 410 DIN 17100 St 44-2 S275J0
KM 132 IS 1079 Gr St 50 IS 1570-1 Fe 490 DIN 17100 St 50-2 EN 10025 E295
EN 10025 S355JR,
KM 133 IS 1079 Gr St 52 DIN 17100 St 52-3 S355J0
IS 513 Cold rolled low carbon steel sheets & strips

KM 134 IS 513 Gr O Ordinary quality
KM 135 IS 513 Gr D Drawing quality
KM 136 IS 513 Gr DD Deep Drawing quality
KM 137 IS 513 Gr EDD Extra Deep Drawing Quality
412704185.xls 6 OF 155
EN 10025 Hot Rolled Products of non alloyed Structural Steels

IS 1079 Gr St 34 ,
KM 138 EN 10025 S185 1.0035 IS 1570-1 Fe 330 DIN 17100 St 33 Base steel, Deoxd-optional.
IS 2062 Gr A, Base steel, Deoxd-optional,
KM 139 EN 10025 S235JR 1.0037 IS 1570-1 Fe 360 DIN 17100 St 37-2 Impact at 200 C - optional
Base steel, Deoxd-rimmed,
KM 140 EN 10025 S235JRG1 1.0036 DIN 17100 USt 37-2 Impact at 200 C - optional
Base steel, non-rimmed,
KM 141 EN 10025 S235JRG2 1.0038 DIN 17100 RSt 37-2 Impact at 200 C-optional
IS 2062 Gr B, Quality steel, non-rimmed,
KM 142 EN 10025 S235J0 1.0114 IS 1570-1 Fe 360 DIN 17100 St 37-3 U Impact at 00 C
IS 2062 Gr C, Quality steel, Deox-fullykilled,
KM 143 EN 10025 S235J2G3 1.0116 IS 1570-1 Fe 360 DIN 17100 St 37-3 N Impact at -200 C, Normalised
Quality steel, Deox-fullykilled,
KM 144 EN 10025 S235J2G4 1.0117 Impact at -200 C.
IS 2062 Gr A, Base steel, non-rimmed,
KM 145 EN 10025 S275JR 1.0044 IS 1570-1 Fe 360 DIN 17100 St 44-2 Impact at 200 C-optional
IS 2062 Gr B, Quality steel, non-rimmed,
KM 146 EN 10025 S275J0 1.0143 IS 1570-1 Fe 360 DIN 17100 St 44-3 U Impact at 00 C
IS 2062 Gr C, Quality steel, Deox-fullykilled,
KM 147 EN 10025 S275J2G3 1.0144 IS 1570-1 Fe 360 DIN 17100 St 44-3 N Impact at -200 C, Normalised
Base steel, non-rimmed,
KM 149 EN 10025 S355JR 1.0045 IS 1079 Gr St 52 Impact at 200 C-optional
Quality steel, non-rimmed,
KM 150 EN 10025 S355J0 1.0553 DIN 17100 St 52-3 U Impact at 00 C
KM 151 EN 10025 S355J2G3 1.0570 DIN 17100 St 52-3 N Impact at -200 C, Normalised
412704185.xls 7 OF 155
KM 153 EN 10025 S355K2G3 1.0595 Better Impact at -200 C.
KM 154 EN 10025 S355K2G4 1.0596 Better Impact at -200 C.
IS 1079 St 50,
KM 155 EN 10025 E 295 1.0050 IS 1570-1 Fe 490 DIN 17100 St 50-2 Base steel, non-rimmed.
ASTM-A-36M Structural Carbon Steel

KM 158 ASTM-A-36M IS 2062 Gr A DIN 17100 St 44-2 EN 10025 S275JR
ASTM-A-283M Low and Intermediate tensile strength Carbon steel plates

KM 159 ASTM-A-283M Grade A
KM 160 ASTM-A-283M Grade B
KM 161 ASTM-A-283M Grade C
KM 162 ASTM-A-283M Grade D
ASTM-A-285M Low and Intermediate strength carbon steel plates for Pressure Vessels
KM 163 ASTM-A-285M Grade A
KM 164 ASTM-A-285M Grade B
KM 165 ASTM-A-285M Grade C
ASTM-A-299M Carbon steel plates for Pressure Vessels

KM 166 ASTM-A-299M
ASTM-A-366M Cold rolled ,Commercial quality Carbon steel sheets

KM 167 ASTM-A-366M
412704185.xls 8 OF 155
ASTM-A-387M Chromium - Molybdenum alloy steel Pressure vessel plates.

KM 168 ASTM-A-387M Grade 2
ASTM-A-569M Hot Rolled, Commercial quality Carbon steel sheet and strip
KM 176 ASTM-A-569M Type A
KM 177 ASTM-A-569M Type B
KM 178 ASTM-A-569M Type C
ASTM-A-573M Structural Carbon Steel Plates with improved toughness

ASTM-A-612M High Strength, Carbon Steel, Pressure Vessel Plates for Moderate & Low Temperature Service
KM 182 ASTM-A-612M
412704185.xls 9 OF 155
4.1.1 WELDABLE, FINE GRAINED STRUCTURAL STEELS
EN 10028-3 Weldable, Normalised, Fine Grained Steel Flat Products for Pressure Purposes
KM 183 EN 10028-3 P275N 1.0486 DIN 17102 StE 285 Unalloyed Quality Steel
KM 184 EN 10028-3 P275NH 1.0487 DIN 17102 WStE 285 Unalloyed Quality Steel
KM 185 EN 10028-3 P275NL1 1.0488 DIN 17102 TStE 285 Unalloyed Quality Steel
KM 186 EN 10028-3 P275NL2 1.1104 DIN 17102 EStE 285 Unalloyed Special Steel
KM 187 EN 10028-3 P355N 1.0562 DIN 17102 StE 355 Unalloyed Quality Steel
KM 188 EN 10028-3 P355NH 1.0565 DIN 17102 WStE 355 Unalloyed Quality Steel
KM 189 EN 10028-3 P355NL1 1.0566 DIN 17102 TStE 355 Unalloyed Quality Steel
KM 190 EN 10028-3 P355NL2 1.1106 DIN 17102 EStE 355 Unalloyed Special Steel
KM 191 EN 10028-3 P460N 1.8905 DIN 17102 StE 460 Alloy Special Steel
KM 192 EN 10028-3 P460NH 1.8935 DIN 17102 WStE 460 Alloy Special Steel
KM 193 EN 10028-3 P460NL1 1.8915 DIN 17102 TStE 460 Alloy Special Steel
KM 194 EN 10028-3 P460NL2 1.8918 DIN 17102 EStE 460 Alloy Special Steel
EN 10113-2 Hot Rolled Products from Weldable, Fine Grain, Normalised Structural Steel
KM 195 EN 10113-2 S275N 1.0490
KM 196 EN 10113-2 S275NL 1.0491
KM 197 EN 10113-2 S355N 1.0545
412704185.xls 10 OF 155
KM 198 EN 10113-2 S355NL 1.0545
KM 199 EN 10113-2 S460N 1.8901
KM 200 EN 10113-2 S460NL 1.8903
4.2 ROLLED / FORGED STEELS

4.2.1 PLAIN CARBON STEELS
IS 1570-2 Wrought Carbon Steel Schedules

KM 201 IS 1570-2 20 C 8 IS 1875 CL 2-20 C 8 DIN 17200 C 22 EN 10083-2 C22
KM 202 IS 1570-2 25 C 4 DIN 17200 C 25 EN 10083-2 C25
KM 203 IS 1570-2 25 C 8 IS 1875 CL 2A-25 C 8 DIN 17200 C 25 EN 10083-2 C25
KM 205 IS 1570-2 35 C 4 DIN 17200 C 30 EN 10083-2 C30
KM 206 IS 1570-2 35 C 8 IS 1875 CL 3A-35 C 8 DIN 17200 C 35 EN 10083-2 C35
KM 207 IS 1570-2 40 C 8 DIN 17200 C 40 EN 10083-2 C40 BS 970-080 M 40
KM 209 IS 1570-2 50 C 4 DIN 17200 C 50 EN 10083-2 C50
KM 210 IS 1570-2 50 C 8 DIN 17200 C 50 EN 10083-2 C50
KM 211 IS 1570-2 55 C 4 DIN 17200 C 55 EN 10083-2 C55
KM 212 IS 1570-2 55 C 8 IS 1875 CL 5-55 C 8 DIN 17200 C 55 EN 10083-2 C55 BS 970-070 M 55
KM 213 IS 1570-2 60 C 4 DIN 17200 C 60 EN 10083-2 C60
412704185.xls 11 OF 155
KM 214 IS 1570-2 60 C 8 DIN 17200 C 60 EN 10083-2 C60
IS 1875 Carbon Steel Billets, Blooms, Slabs, & Bars for Forgings
KM 215 IS 1875 Class 1-14 C 6 IS 1570-2 14 C 6
KM 216 IS 1875 Class 1A-15 C 8 IS 1570-2 15 C 8
KM 217 IS 1875 Class 2-20 C 8 IS 1570-2 20 C 8 DIN 17200 C 22 EN 10083-2 C22
KM 218 IS 1875 Class 2A-25 C 8 IS 1570-2 25 C 8 DIN 17200 C 25 EN 10083-2 C25
KM 220 IS 1875 Class 3A-35 C 8 IS 1570-2 35 C 8 DIN 17200 C 35 EN 10083-2 C35
KM 222 IS 1875 Class 5-55 C 8 IS 1570-2 55 C 8 DIN 17200 C 55 EN 10083-2 C55 BS 970-070 M 55
KM 223 IS 1875 Class 6-65 C 6
BS 970-3 Wrought Steels for Mechanical & Allied Engineering Purposes

KM 224 BS 970-3 080 M 40 ( En 8 ) IS 1570-2 40 C 8 DIN 17200 C 40 EN 10083-2-C40 Plain Carbon Steel forgings
KM 225 BS 970-3 070 M 55 ( En 9 ) IS 1570-2 55 C 8 DIN 17200 C 55 EN 10083-2-C55 Plain Carbon Steel forgings
DIN 17200 EN 10083 -1
KM 226 BS 970-3 709 M 40 (En 19) 36 CrNiMo 4 36CrNiMo4 Low alloy steel forgings
DIN 17200 EN 10083 -1
KM 227 BS 970-3 817 M 40 (En 24) 34 CrNiMo 8 34CrNiMo8 Low alloy steel forgings
EN 10083 Quenched & Tempered Unalloyed Quality Steels

IS 1875 CL 2-20 C8,
KM 228 EN 10083-2 C22 1.0402 IS 1570-2 20 C 8 DIN 17200 C 22 Ordinary Plain Carbon steel
IS 1875 CL 2-20 C8,
KM 229 EN 10083-1 C22E 1.1151 IS 1570-2 20 C 8 DIN 17200 Ck 22 Quality C steel with low S,P.
IS 1875 CL 2-20 C8,
KM 230 EN 10083-1 C22R 1.1149 IS 1570-2 20 C 8 DIN 17200 Cm 22 Quality C steel with controlled S,P.
IS 1875 CL 2A-25 C8,
412704185.xls 12 OF 155
IS 1875 CL 2A-25 C8,
IS 1875 CL 2A-25 C8,
IS 1875 CL 3-30 C8,
IS 1875 CL 3-30 C8,
IS 1875 CL 3-30 C8,
KM 237 EN 10083-2 C35 1.0501 IS1875 CL 3A-35 C8 DIN 17200 C 35 Ordinary Plain Carbon steel
KM 238 EN 10083-1 C35E 1.1181 IS1875 CL 3A-35 C8 DIN 17200 Ck 35 Quality C steel with low S,P.
KM 239 EN 10083-1 C35R 1.1180 IS1875 CL 3A-35 C8 DIN 17200 Cm 35 Quality C steel with controlled S,P.
KM 240 EN 10083-2 C40 1.0511 IS 1570-2 40 C8 DIN 17200 C 40 BS 970 080M40 Ordinary Plain Carbon steel
KM 241 EN 10083-1 C40E 1.1186 IS 1570-2 40 C8 DIN 17200 Ck 40 Quality C steel with low S,P.
KM 242 EN 10083-1 C40R 1.1189 IS 1570-2 40 C8 DIN 17200 Cm 40 Quality C steel with controlled S,P.
IS 1875 CL 4-45 C8,
IS 1875 CL 4-45 C8,
IS 1875 CL 4-45 C8,
KM 246 EN 10083-2 C50 1.054 IS 1570-2 50C8,50C4 DIN 17200 C 50 Ordinary Plain Carbon steel
KM 247 EN 10083-1 C50E 1.1206 IS 1570-2 50C8,50C4 DIN 17200 Ck 50 Quality C steel with low S,P.
KM 248 EN 10083-1 C50R 1.1241 IS 1570-2 50C8,50C4 DIN 17200 Cm 50 Quality C steel with controlled S,P.
IS 1875 CL 5-55 C8, BS 970
KM 249 EN 10083-2 C55 1.0535 IS 1570-2 55C8,55 C4 DIN 17200 C 55 070M55 Ordinary Plain Carbon steel
IS 1875 CL 5-55 C8,
KM 250 EN 10083-1 C55E 1.1203 IS 1570-2 55C8,55 C4 DIN 17200 Ck 55 Quality C steel with low S,P.
IS 1875 CL 5-55 C8,
KM 251 EN 10083-1 C55R 1.1209 IS 1570-2 55C8,55 C4 DIN 17200 Cm 55 Quality C steel with controlled S,P.
KM 252 EN 10083-2 C60 1.0601 IS 1570-2 60C6,60C4 DIN 17200 C 60 Ordinary Plain Carbon steel
412704185.xls 13 OF 155
KM 253 EN 10083-1 C60E 1.1221 IS 1570-2 60C6,60C4 DIN 17200 Ck 60 Quality C steel with low S,P.
KM 254 EN 10083-1 C60R 1.1223 IS 1570-2 60C6,60C4 DIN 17200 Cm 60 Quality C steel with controlled S,P.
KM 255 EN 10083-1 28Mn6 1.117 DIN 17200 28 Mn 6
4.2.2 LOW ALLOY STEELS
EN 10083-1 Quenched & Tempered Special Steels

KM 256 EN 10083-1 38Cr2 1.7003 DIN 17200 38 Cr 2
KM 257 EN 10083-1 46Cr2 1.7006 DIN 17200 46 Cr 2
KM 258 EN 10083-1 34Cr4 1.7033 DIN 17200 34 Cr 4
KM 259 EN 10083-1 37Cr4 1.7034 DIN 17200 37 Cr 4
KM 260 EN 10083-1 41Cr4 1.7035 DIN 17200 41 Cr 4
KM 261 EN 10083-1 25CrMo4 1.7218 DIN 17200 25 CrMo 4
KM 264 EN 10083-1 42CrMoS4 1.7227 DIN 17200 42 CrMoS 4
412704185.xls 14 OF 155
DIN 17200 BS 970
KM 266 EN 10083-1 36CrNiMo4 1.6511 36 CrNiMo 4 709 M 40
DIN 17200
KM 267 EN 10083-1 34CrNiMo6 1.6582 34 CrNiMo 6
DIN 17200
KM 268 EN 10083-1 30CrNiMo8 1.6580 30 CrNiMo 8
KM 269 EN 10083-1 36NiCrMo16 1.6773
IS 2507 Gr 11
KM 270 EN 10083-1 51CrV4 1.8159 50 Cr 4 V 2 DIN 17200 50 CrV 4
ASTM-A-108 Cold Finished , Standard quality Carbon Steel bars

KM 271 ASTM-A-108 1010
KM 272 ASTM-A-108 1015
KM 273 ASTM-A-108 1020
KM 274 ASTM-A-108 1025
KM 275 ASTM-A-108 1030
KM 276 ASTM-A-108 1035
KM 277 ASTM-A-108 1040
KM 278 ASTM-A-108 1045
KM 279 ASTM-A-108 1050
KM 280 ASTM-A-108 1141
KM 281 ASTM-A-108 1151
KM 282 ASTM-A-108 1211
KM 283 ASTM-A-108 1215
ASTM-A-322 Standard grades of Alloy Steel bars

KM 284 ASTM-A-322 1330
KM 285 ASTM-A-322 1340
KM 286 ASTM-A-322 4023
KM 287 ASTM-A-322 4047
412704185.xls 15 OF 155
KM 288 ASTM-A-322 4130
KM 289 ASTM-A-322 4140
KM 290 ASTM-A-322 4320
KM 291 ASTM-A-322 4615
KM 292 ASTM-A-322 4720
KM 293 ASTM-A-322 4815
KM 294 ASTM-A-322 5120
KM 295 ASTM-A-322 5140
KM 296 ASTM-A-322 6150
KM 297 ASTM-A-322 8640
KM 298 ASTM-A-322 8645
KM 299 ASTM-A-322 8720
KM 300 ASTM-A-322 9260
4.3 CARBON STEEL CASTINGS
IS 276 Austenitic Manganese Steel Castings Work Hardening type Hadfields Manganese steel
KM 301 IS 276 Grade 1
KM 303 IS 276 Grade 3 SEW 390-GX120Mn12
412704185.xls 16 OF 155
IS 1030 Carbon Steel Castings for General Engineering Purposes
KM 306 IS 1030 200-400 N DIN 1681 GS - 38 Normal Grade
KM 307 IS 1030 200-400 W DIN 17182 GS-16 Mn 5 Weldable Grade
ASTM-A-27M
KM 308 IS 1030 230-450 N DIN 1681 GS - 45 65 - 35 Normal Grade
KM 309 IS 1030 230-450 W DIN 17182 GS-20 Mn 5 Weldable Grade
ASTM-A-148M
KM 310 IS 1030 280-520 N DIN 1681 GS - 52 80 - 40 Normal Grade
KM 311 IS 1030 280-520 W Weldable Grade
KM 312 IS 1030 340-570 N DIN 17205 GS-30 Mn 5 Normal Grade
KM 313 IS 1030 340-570 W Weldable Grade
IS 2644 High Strength Steel Castings for General Engineering & Structural Purposes
KM 314 IS 2644 Gr 1 - CS 640
DIN 17205 ASTM-A-148M
KM 315 IS 2644 Gr 2 - CS 700 GS-25 CrMo 4 105-85
DIN 17205
KM 316 IS 2644 Gr 3 - CS 840 GS-34 CrMo 4
KM 317 IS 2644 Gr 4 - CS 1030 GS-35 CrMoV 10 4 150-135
KM 318 IS 2644 Gr 5 - CS 1230
IS 2707 Carbon Steel Castings for Surface Hardening

IS 2708 1.5 % Manganese Steel Castings for General Engineering Purposes
412704185.xls 17 OF 155
IS 2856 Welding Quality Carbon Steel Castings for High Temperature & Pressure Service
DIN 1681 Steel Castings for General Purposes
KM 328 DIN 1681 GS - 38 1.0420 IS 1030 200-400 N
ASTM-A-27M
KM 329 DIN 1681 GS - 45 1.0446 IS 1030 230-450 N 65 - 35
ASTM-A-148M
KM 330 DIN 1681 GS - 52 1.0552 IS 1030 280-520 N 80 - 40
KM 331 DIN 1681 GS - 60 1.0558
DIN 17182 General Purpose Steel Castings with Enhanced Weldability & Toughness
KM 332 DIN 17182 GS - 16 Mn 5 1.1131 IS 1030 230-450 W
KM 333 DIN 17182 GS - 20 Mn 5 1.1120 IS 1030 280-520 W
ASTM-A-27M Carbon Steel Castings for General Applications

KM 334 ASTM-A-27M N-1
KM 335 ASTM-A-27M N-2
KM 336 ASTM-A-27M U-60-30
KM 337 ASTM-A-27M 60-30
KM 338 ASTM-A-27M 65-35 IS 1030 230-450 N DIN 1681 GS - 45
KM 339 ASTM-A-27M 70-36
KM 340 ASTM-A-27M 70-40
ASTM-A-128M Austenitic Manganese Steel Castings

KM 341 ASTM-A-128M A
KM 342 ASTM-A-128M B-1
412704185.xls 18 OF 155
KM 346 ASTM-A-128M C
KM 347 ASTM-A-128M D
KM 348 ASTM-A-128M E-1
KM 349 ASTM-A-128M E-2
KM 350 ASTM-A-128M F
ASTM-A-148M High Strength Steel Castings for Structural Purposes

KM 351 ASTM-A-148M 80 - 40 IS 1030 280-520 N DIN 1681 GS - 52
KM 352 ASTM-A-148M 80 - 50
KM 353 ASTM-A-148M 90 - 60
KM 354 ASTM-A-148M 105 - 85 IS 2644 Gr 2 - CS 700
KM 355 ASTM-A-148M 115 - 95
KM 356 ASTM-A-148M 130 - 115
KM 357 ASTM-A-148M 135 - 125
KM 358 ASTM-A-148M 150 - 135 IS 2644 Gr 4 - CS 1030
KM 359 ASTM-A-148M 160 - 145
KM 360 ASTM-A-148M 165 - 150
KM 361 ASTM-A-148M 210 - 180
KM 362 ASTM-A-148M 260 - 210
ASTM-A-216M Carbon Steel Castings for High Temperature Service, Suitable for Fusion Welding
KM 363 ASTM-A-216M WCA
KM 364 ASTM-A-216M WCB
KM 365 ASTM-A-216M WCC
4.4 ALLOY STEEL CASTINGS
IS 4522 Heat Resistant Alloy Steel & Nickel base Castings

412704185.xls 19 OF 155
KM 410 IS 4522 Grade 10
KM 411 IS 4522 Grade 11
KM 412 IS 4522 Grade 12
KM 413 IS 4522 Grade 13
KM 414 IS 4522 Grade 14
DIN 17205 Quenched and Tempered Steel Castings for General Applications
KM 415 DIN 17205 GS - 30 Mn 5 1.1165 IS 1030 340-570 N
KM 416 DIN 17205 GS - 25 CrMo 4 1.7218 IS 2644 Gr 2 - CS 700
KM 417 DIN 17205 GS - 34 CrMo 4 1.7220 IS 2644 Gr 3 - CS 840
KM 418 DIN 17205 GS - 42 CrMo 4 1.7225
KM 419 DIN 17205 GS-30 CrMoV 6 4 1.7725
KM 420 DIN 17205 GS-35 CrMoV 10 4 1.7755 IS 2644 Gr 4 - CS 1030
KM 421 DIN 17205 GS-25 CrNiMo 4 1.6515
KM 422 DIN 17205 GS-34 CrNiMo 6 1.6582
KM 423 DIN 17205 GS-30 NiCrMo 8 5 1.6570
KM 424 DIN 17205 GS-33 NiCrMo 7 4 4 1.6740
EN 10213 Steel Castings for Pressure Purposes for use at Room Temperature and Elevated Temperature
KM 425 EN 10213 GP240GR 1.0621
KM 426 EN 10213 GP240GH 1.0619 DIN 17245 GS-C 25
412704185.xls 20 OF 155
KM 427 EN 10213 GP280GH 1.0625
DIN 17245
KM 428 EN 10213 G20Mo5 1.5419 GS-22 Mo 4
DIN 17245
KM 429 EN 10213 G17CrMo5-5 1.7357 GS-17CrMo5 5
DIN 17245
KM 430 EN 10213 G17CrMo9-10 1.7379 GS-18CrMo9 10
KM 431 EN 10213 G12MoCrV5-2 1.7720
DIN 17245
KM 432 EN 10213 G17CrMoV5-10 1.7706 GS-17CrMoV5 11
KM 433 EN 10213 GX15CrMo5 1.7365
DIN 17245
KM 434 EN 10213 GX8CrNi12 1.4107 G-X 8 CrNi 12
KM 435 EN 10213 GX4CrNi13-4 1.4317
DIN 17245
KM 436 EN 10213 GX23CrMoV12-1 1.4931 G-X 22CrMoV12 1
KM 437 EN 10213 GX4CrNiMo16-5-1 1.4405
DIN 17465 Heat Resistant Steel Castings

KM 438 DIN 17465 GX30CrSi6 1.4710
KM 439 DIN 17465 GX40CrSi13 1.4729
KM 440 DIN 17465 GX40CrSi17 1.4740
KM 441 DIN 17465 GX40CrSi23 1.4745
KM 442 DIN 17465 GX40CrSi29 1.4776
KM 443 DIN 17465 GX130CrSi29 1.4777
KM 444 DIN 17465 GX40CrNiSi27-4 1.4823
KM 445 DIN 17465 GX25CrNiSi18-9 1.4825
KM 446 DIN 17465 GX40CrNiSi22-9 1.4826
KM 447 DIN 17465 GX25CrNiSi 20-14 1.4832
KM 448 DIN 17465 GX40CrNiSi25-12 1.4837
KM 449 DIN 17465 GX40CrNiSi25-20 1.4848
412704185.xls 21 OF 155
KM 450 DIN 17465 GX40NiCrSi38-18 1.4865
KM 451 DIN 17465 GX40NiCrSi35-25 1.4857
KM 452 DIN 17465 GX30CrNiSiNb24-24 1.4855
KM 453 DIN 17465 GX40NiCrSiNb38-18 1.4849
KM 454 DIN 17465 GX40NiCrSiNb35-25 1.4852
ASTM-A-351M Austenitic & Duplex Steel Castings for Pressure Containing Parts
KM 455 ASTM-A-351M CF 3
KM 456 ASTM-A-351M CF 3 A
KM 458 ASTM-A-351M CF 8 A
KM 459 ASTM-A-351M CF 3 M
KM 460 ASTM-A-351M CF 3 MA
KM 462 ASTM-A-351M CF 3 MN
KM 463 ASTM-A-351M CF 8 C
KM 466 ASTM-A-351M CH 8
KM 469 ASTM-A-351M CK 20
KM 470 ASTM-A-351M HK 30
KM 471 ASTM-A-351M HK 40
KM 472 ASTM-A-351M HT 30
412704185.xls 22 OF 155
ASTM-A-297M Heat resistant Iron-Chromium-Nickel Steel Castings for General Application
KM 473 ASTM-A-297M HF- 19Cr,9Ni
KM 474 ASTM-A-297M HH- 25Cr,12Ni
KM 475 ASTM-A-297M HI- 28Cr,15Ni
KM 476 ASTM-A-297M HK- 25 Cr,20Ni
KM 477 ASTM-A-297M HE- 29Cr,9Ni
KM 478 ASTM-A-297M HT- 15Cr,35Ni
KM 479 ASTM-A-297M HU- 19Cr,39Ni
KM 480 ASTM-A-297M HW- 12Cr,60Ni
KM 481 ASTM-A-297M HX- 17Cr,66Ni
KM 482 ASTM-A-297M HC- 28Cr
KM 483 ASTM-A-297M HD- 28Cr.5Ni
KM 484 ASTM-A-297M HL- 29Cr,20Ni
KM 485 ASTM-A-297M HN- 20Cr,25Ni
KM 486 ASTM-A-297M HP- 26Cr,35Ni
SEW 390 Austenitic Manganese steel

KM 487 SEW 390 GX - 120 Mn 12 1.3802 IS 276 Grade 3
DIN 17350 Tool Steel

KM 488 DIN 17350 X-165 CrMoV 12 1.2601
SEW 835 Steel Castings for Flame & Induction Hardening

KM 489 SEW 835 G36Mn5 1.1176
412704185.xls 23 OF 155
4.5 CAST IRONS Microstructure

4.5.1 GREY CAST IRONS
IS 210 GREY CAST IRONS
KM 501 IS 210 FG 150 DIN 1691 GG-15 EN 1561 EN-GJL-150
KM 503 IS 210 FG 220
KM 507 IS 210 FG 400
EN 1561 GREY CAST IRONS Graphite flakes in matrix of

KM 508 EN 1561 EN-GJL-100 EN-JL-1010 DIN 1691 GG -10 Ferrite + Perlite
KM 509 EN 1561 EN-GJL-150 EN-JL-1020 IS 210 FG -150 DIN 1691 GG-15 Ferrite + Perlite
KM 510 EN 1561 EN-GJL-200 EN-JL-1030 IS 210 FG -200 DIN 1691 GG-20 Perlite
ASTM-A-48M GREY CAST IRONS

KM 514 ASTM-A-48M 150
KM 515 ASTM-A-48M 175
KM 516 ASTM-A-48M 200
KM 517 ASTM-A-48M 225
KM 518 ASTM-A-48M 250
KM 519 ASTM-A-48M 275
KM 520 ASTM-A-48M 300
412704185.xls 24 OF 155
KM 521 ASTM-A-48M 325
KM 522 ASTM-A-48M 350
KM 523 ASTM-A-48M 375
KM 524 ASTM-A-48M 400
4.5.2 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS Graphite nodules in matrix of

IS 1865 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS
EN 1563
KM 525 IS 1865 SG 900/2 EN-GJS-900-2 Temp martensite
EN 1563
KM 526 IS 1865 SG 800/2 DIN 1693 GGG-80 EN-GJS-800-2 Perlite
EN 1563
KM 527 IS 1865 SG 700/2 DIN 1693 GGG-70 EN-GJS-700-2 Perlite
EN 1563
KM 528 IS 1865 SG 600/3 DIN 1693 GGG-60 EN-GJS-600-3 Perlite + Ferrite
EN 1563
KM 529 IS 1865 SG 500/7 DIN 1693 GGG-50 EN-GJS-500-7 Ferrite + Perlite
EN 1563
KM 530 IS 1865 SG 450/10 EN-GJS-450-10 Ferrite
EN 1563
KM 531 IS 1865 SG 400/15 DIN 1693 GGG-40 EN-GJS-400-15 Ferrite
EN 1563
KM 532 IS 1865 SG 400/18 DIN 1693 GGG-40.3 EN-GJS-400-18-LT Ferrite
EN 1563
KM 533 IS 1865 SG 350/22 DIN 1693 GGG-35.3 EN-GJS-350-22-LT Ferrite
EN 1563 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

KM 534 EN 1563 EN-GJS-350-22-LT EN-JS1015 IS 1865 SG 350/22 DIN 1693 GGG-35.3
KM 535 EN 1563 EN-GJS-400-18-LT EN-JS1025 IS 1865 SG 400/18 DIN 1693 GGG-40.3
KM 536 EN 1563 EN-GJS-400-15 EN-JS1030 IS 1865 SG 400/15 DIN 1693 GGG-40 Ferrite
KM 537 EN 1563 EN-GJS-500-7 EN-JS1050 IS 1865 SG 500/7 DIN 1693 GGG-50 Ferrite + Perlite
KM 538 EN 1563 EN-GJS-600-3 EN-JS1060 IS 1865 SG 600/3 DIN 1693 GGG-60 Perlite + Ferrite
412704185.xls 25 OF 155
KM 539 EN 1563 EN-GJS-700-2 EN-JS1070 IS 1865 SG 700/2 DIN 1693 GGG-70 Perlite
KM 540 EN 1563 EN-GJS-800-2 EN-JS1080 IS 1865 SG 800/2 DIN 1693 GGG-80 Perlite + Temp Martensite
ASTM-A-536M NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

KM 541 ASTM-A-536M 60-40-18
KM 542 ASTM-A-536M 65-45-12
KM 543 ASTM-A-536M 80-55-06
KM 544 ASTM-A-536M 100-70-03
KM 545 ASTM-A-536M 120-90-02
KM 546 ASTM-A-536M 60-42-10
KM 547 ASTM-A-536M 70-50-05
KM 548 ASTM-A-536M 80-60-03
4.5.3 MALLEABLE CAST IRONS Microstructure
IS 2107 MALLEABLE CAST IRONS

KM 549 IS 2107 WM 410 Ferrite
KM 550 IS 2107 WM 340 Perlite + Ferrite
EN 1562 MALLEABLE CAST IRONS

KM 551 EN 1562 EN-GJMB-350-10 EN-JM1130 DIN 1692 GTS-35-10 Perlite + Ferrite
KM 552 EN 1562 EN-GJMB-450-6 EN-JM1140 DIN 1692 GTS-45-06 Perlite
KM 553 EN 1562 EN-GJMB-550-4 EN-JM1160 DIN 1692 GTS-55-04
KM 556 EN 1562 EN-GJMW-350-4 EN-JM1010 DIN 1692 GTW-35-04
412704185.xls 26 OF 155
KM 559 EN 1562 EN-GJMW-360-12 EN-JM1020 DIN 1692 GTW-S-38-12
ASTM-A-47M MALLEABLE CAST IRONS

KM 560 ASTM-A-47M 22010 Ferrite

KM 561 ASTM-A-220M 280M10 Perlite
412704185.xls 27 OF 155
4.6 STAINLESS STEELS

4.6.1 AUSTENITIC STAINLESS STEELS
ASTM-A-240M Heat Resisting Chromium-Nickel Stainless Steel Plates,Sheets & Strips for Pressure Vessels
KM 601 ASTM-A-240M 201
KM 602 ASTM-A-240M 202
KM 603 ASTM-A-240M 301
KM 604 ASTM-A-240M 302
DIN 17440 EN 10088
KM 605 ASTM-A-240M 304 X 5 CrNi 18 10 X5CrNi18-10
DIN 17440 EN 10088
KM 606 ASTM-A-240M 304 L X 2 CrNi 19 11 X2CrNi19-11
KM 607 ASTM-A-240M 304 H
KM 608 ASTM-A-240M 304 N
DIN 17440 EN 10088
KM 609 ASTM-A-240M 304 L N X 2 CrNiN 18 10 X2CrNiN18-10
KM 610 ASTM-A-240M 305
KM 611 ASTM-A-240M 309 S
KM 612 ASTM-A-240M 309 H
KM 613 ASTM-A-240M 309 Cb
KM 614 ASTM-A-240M 309 H Cb
KM 615 ASTM-A-240M 310 S
412704185.xls 28 OF 155
KM 616 ASTM-A-240M 310 H
KM 618 ASTM-A-240M 310 H Cb
KM 619 ASTM-A-240M 310 Mo L N
DIN 17440 EN 10088
X 5 CrNiMo 17 12 2, X5CrNiMo17-12-2,
KM 620 ASTM-A-240M 316 X 5 CrNiMo 17 13 3 X3CrNiMo17-13-3
DIN 17440 EN 10088
KM 621 ASTM-A-240M 316 L X 2 CrNiMo 17 13 2 X2CrNiMo17-12-2
KM 622 ASTM-A-240M 316 H
DIN 17440 EN 10088
KM 623 ASTM-A-240M 316 Ti X 6 CrNiMoTi 17 12 2 X6CrNiMoTi17-12-2
KM 625 ASTM-A-240M 316 N
DIN 17440 EN 10088

X 2 CrNiMoN 17 13 3, X2CrNiMoN17-13-3,
KM 626 ASTM-A-240M 316 L N X 2 CrNiMoN 17 12 2 X2CrNiMoN17-11-2
KM 627 ASTM-A-240M 317
DIN 17440 EN 10088
KM 628 ASTM-A-240M 317 L X 2 CrNiMo 18 16 4 X2CrNiMo18-15-4
DIN 17440 EN 10088
KM 629 ASTM-A-240M 317 L N X 2 CrNiMoN 17 13 5 X2CrNiMoN17-13-5
DIN 17440 EN 10088
KM 630 ASTM-A-240M 321 X 6 CrNiTi 18 10 X6CrNiTi18-10
KM 631 ASTM-A-240M 321 H
KM 632 ASTM-A-240M 347
KM 633 ASTM-A-240M 347 H
KM 634 ASTM-A-240M 348
KM 635 ASTM-A-240M 348 H
EN 10088-2 Stainless Steel Plates, Sheets & Strips for General Purpose
KM 636 EN 10088-2 X5CrNi18-10 1.4301 X 5 CrNi 18 10 304
412704185.xls 29 OF 155
DIN 17440
KM 637 EN 10088-2 X4CrNi18-12 1.4303 X 5 CrNi 18 12
DIN 17440
KM 638 EN 10088-2 X8CrNiS18-9 1.4305 X 10 CrNiS 18 9
KM 639 EN 10088-2 X2CrNi19-11 1.4306 X 2 CrNi 19 11 304 L
KM 640 EN 10088-2 X2CrNiN18-10 1.4311 X 2 CrNiN 18 10 304 LN
KM 641 EN 10088-2 X6CrNiTi18-10 1.4541 X 6 CrNiTi 18 10 321
DIN 17440
KM 642 EN 10088-2 X6CrNiNb18-10 1.4550 X 6 CrNiNb 18 10
KM 643 EN 10088-2 X5CrNiMo17-12-2 1.4401 X 5 CrNiMo 17 12 2 316
KM 644 EN 10088-2 X2CrNiMo17-12-2 1.4404 X 2 CrNiMo 17 13 2 316 L
KM 645 EN 10088-2 X2CrNiMoN17-11-2 1.4406 X 2 CrNiMoN 17 12 2 316 LN
KM 646 EN 10088-2 X6CrNiMoTi17-12-2 1.4571 X 6 CrNiMoTi 17 12 2 316 Ti
DIN 17440
KM 647 EN 10088-2 X6CrNiMoNb17-12-2 1.4580 X6 CrNiMoNb17 12 2
DIN 17440
KM 649 EN 10088-2 X2CrNiMo18-14-3 1.4435 X 2 CrNiMo 18 14 3
KM 650 EN 10088-2 X3CrNiMo17-13-3 1.4436 X 5 CrNiMo 17 13 3 316
KM 651 EN 10088-2 X2CrNiMo18-15-4 1.4438 X 2 CrNiMo 18 16 4 317 L
412704185.xls 30 OF 155
4.6.2 FERRITIC & MARTENSITIC STAINLESS STEELS
DIN 17440 EN 10088
KM 653 ASTM-A-240M 405 X 6 CrAl 13 X6CrAl13
KM 654 ASTM-A-240M 409
KM 655 ASTM-A-240M 429
KM 656 ASTM-A-240M 430
DIN 17440 EN 10088
KM 657 ASTM-A-240M 439 X 6 CrTi 17 X6CrTi17
KM 658 ASTM-A-240M 444
KM 659 ASTM-A-240M 410
KM 660 ASTM-A-240M 410 S DIN 17440-X 6 Cr 13 EN 10088 - X6Cr13
KM 661 EN 10088-2 X6Cr13 1.4000 X 6 Cr 13 410 S
KM 662 EN 10088-2 X6CrAl13 1.4002 X 6 CrAl 13 405
KM 663 EN 10088-2 X6Cr17 1.4016 DIN 17440 X 6 Cr 17
KM 664 EN 10088-2 X3CrTi17 1.4510 X 6 CrTi 17 439
DIN 17440
KM 665 EN 10088-2 X6CrMoS17 1.4105 X 4 CrMoS 18
KM 666 EN 10088-2 X12Cr13 1.4006 DIN 17440 X 10 Cr 13
KM 667 EN 10088-2 X12CrS13 1.4005
DIN 17440
KM 668 EN 10088-2 X20Cr13 1.4021 X 20 Cr 13
DIN 17440
KM 669 EN 10088-2 X30Cr13 1.4028 X 30 Cr 13
DIN 17440
KM 670 EN 10088-2 X39Cr13 1.4031 X 38 Cr 13
412704185.xls 31 OF 155
DIN 17440
KM 671 EN 10088-2 X46Cr13 1.4034 X 46 Cr 13
DIN 17440
KM 672 EN 10088-2 X50CrMoV15 1.4116 X 45 CrMoV 15
DIN 17440
KM 673 EN 10088-2 X14CrMoS17 1.4104 X 12 CrMoS 17
DIN 17440
KM 674 EN 10088-2 X17CrNi16-2 1.4057 X 20 CrNi 17 2
KM 675 EN 10088-2 X3CrNiMo13-4 1.4313
4.6.3 DUPLEX STAINLESS STEELS

EN 10088
KM 676 ASTM-A-240M UNS-S31803 X2CrNiMoN22-5-3
EN 10088
KM 677 ASTM-A-240M UNS-S32205 X2CrNiMoN22-5-3
EN 10088
KM 678 ASTM-A-240M UNS-S32304 X2CrNiN23-4
KM 679 ASTM-A-240M 329
SEW 400
KM 680 EN 10088-2 X3CrNiMoN27-5-2 1.4460 X 4 CrNiMoN 27 5 2
SEW 400 UNS-S31803
KM 681 EN 10088-2 X2CrNiMoN22-5-3 1.4462 X 2 CrNiMoN 22 5 3 UNS-S32205
SEW 400
KM 682 EN 10088-2 X2CrNiN23-4 1.4362 X 2 CrNiN 23 4 UNS-S32304
4.7 HIGH TEMPERATURE STEELS

4.7.1 PLATES AND BARS
412704185.xls 32 OF 155
EN 10028-2 Unalloyed & Alloy Steel Flat Products with Elevated Temperature Properties for Pressure Purposes
ASTM-A-516M
KM 701 EN 10028-2 P235GH 1.0345 IS 2002 Grade 1 DIN 17155 - H I Gr 55
ASTM-A-515M
Gr 60, ASTM-
KM 702 EN 10028-2 P265GH 1.0425 IS 2002 Grade 2 DIN 17155 - H II A-516M Gr 60
ASTM-A-515M
Gr 65, ASTM-
KM 703 EN 10028-2 P295GH 1.0481 IS 2002 Grade 3 DIN 17155-17 Mn 4 A-516M Gr 65
KM 704 EN 10028-2 P355GH 1.0473 DIN 17155-19 Mn 6
ASTM-A-515M
Gr 65, ASTM-
KM 705 EN 10028-2 16Mo3 1.5415 IS 2002 Grade 3 DIN 17155 - 15 Mo 3 A-516M Gr 65
ASTM-A-515M
DIN 17155 Gr 65, ASTM-
KM 706 EN 10028-2 13CrMo4-5 1.7335 IS 2002 Grade 3 13 CrMo 4 4 A-516M Gr 65
ASTM-A-515M
DIN 17155 Gr 70, ASTM-
KM 707 EN 10028-2 10CrMo9-10 1.7380 10 CrMo 9 10 A-516M Gr 70
KM 708 EN 10028-2 11CrMo9-10 1.7383
ASTM-A-515M Carbon Steel Pressure Vessel Plates for Intermediate & High Temperature Service
KM 709 ASTM-A-515M Grade 60 IS 2002 Grade 2 DIN 17155 - H II EN 10028-2 P265GH

EN 10028-2
DIN 17155 17Mn4, P295GH,16Mo3,
KM 710 ASTM-A-515M Grade 65 IS 2002 Grade 3 15 Mo 3,13CrMo4 4 13CrMo4-5
412704185.xls 33 OF 155
DIN 17155 EN 10028-2
KM 711 ASTM-A-515M Grade 70 10 CrMo 9 10 10CrMo9-10
ASTM-A-516M Carbon Steel Pressure Vessel Plates for Moderate & Lower Temperature Service
KM 712 ASTM-A-516M Grade 55 IS 2002 Grade 1 DIN 17155 - H I EN 10028-2 P235GH
KM 713 ASTM-A-516M Grade 60 IS 2002 Grade 2 DIN 17155 - H II EN 10028-2 P265GH

EN 10028-2
DIN 17155 17Mn4, P295GH,16Mo3,
KM 714 ASTM-A-516M Grade 65 IS 2002 Grade 3 15 Mo 3,13CrMo4 4 13CrMo4-5
DIN 17155 EN 10028-2
KM 715 ASTM-A-516M Grade 70 10 CrMo 9 10 10CrMo9-10
IS 2002 Steel Pressure Vessel Plates for Intermediate & High Temperature Service including Boilers
ASTM-A-516M
KM 716 IS 2002 Grade 1 DIN 17155 - H I EN 10028-2 P235GH Gr 55
ASTM-A-515M
Gr 60, ASTM-
KM 717 IS 2002 Grade 2 DIN 17155 - H II EN 10028-2 P265GH A-516M Gr 60
EN 10028-2 ASTM-A-515M
DIN 17155 17Mn4, P295GH,16Mo3 Gr 65, ASTM-
KM 718 IS 2002 Grade 3 15 Mo 3,13CrMo4 4 13CrMo4-5 A-516M Gr 65
BS 1501-1 Carbon-Manganese Steel Plates for Fired and Unfired Pressure Vessels
KM 719 BS 1501-1 141 - Gr 360 Rimmed carbon steel
KM 720 BS 1501-1 154 - Gr 360 Semi-killed with Aluminium
412704185.xls 34 OF 155
KM 723 BS 1501-1 151 - Gr 360 Fully killed or semi-killed C.S
KM 726 BS 1501-1 161 - Gr 360 Fully killed Carbon Steel
KM 729 BS 1501-1 164 - Gr 360 Fully-killed, Al treated C.S
KM 730 BS 1501-1 164 - Gr 400 Fully-killed, Al treated C.S
KM 731 BS 1501-1 223 - Gr 460 Fully-killed, Nb treated C-Mn steel
KM 732 BS 1501-1 223 - Gr 490 Fully-killed, Nb treated C-Mn steel
KM 733 BS 1501-1 224 - Gr 400 Fully-killed, Al treated C-Mn steel
KM 737 BS 1501-1 225 - Gr 460 Fully-killed, Al+Nb treated C-Mn steel
KM 738 BS 1501-1 225 - Gr 490 Fully-killed, Al+Nb treated C-Mn steel
4.7.2 TUBES AND PIPES
BS 3059-1 Boiler & Superheater Low Tensile Carbon Steel Tubes w.o. Specified Elevated Temperature Props
KM 739 BS 3059-1 HFS 320 Hot Finished Seamless
KM 740 BS 3059-1 CFS 320 Cold Finished Seamless
KM 741 BS 3059-1 ERW 320 Electric Resistance Welded
KM 742 BS 3059-1 CEW 320 Cold finished Electric Welded
BS 3059-2 Boiler & Superheater, Carbon, Alloy & Stainless Steel Tubes with Elevated Temperature Properties
KM 743 BS 3059-2 360 Plain Carbon steel type
412704185.xls 35 OF 155
KM 744 BS 3059-2 440 Carbon Manganese steel type
KM 745 BS 3059-2 243 Ferritic alloy steel type
KM 746 BS 3059-2 620-460 Ferritic alloy steel type
KM 750 BS 3059-2 762 Ferritic alloy steel type
KM 751 BS 3059-2 304S51 Austenitic stainless steel type
KM 754 BS 3059-2 321S51 (1010) Austenitic stainless steel type
KM 755 BS 3059-2 321S51 (1105) Austenitic stainless steel type
BS 3602-1 Seamless, Electric Resistance Welded & Induction Welded Pipes & Tubes of Carbon-Manganese Steels
for Pressure Purposes with Specified Elevated Temperature Properties
KM 758 BS 3602-1 360 - Seamless
KM 759 BS 3602-1 360 - Welded
KM 760 BS 3602-1 430 - Seamless
KM 761 BS 3602-1 430 - Welded
KM 762 BS 3602-1 500 Nb - Seamless
BS 3602-2 Longitudinally Arc Welded Pipes & Tubes of Carbon-Manganese Steels
412704185.xls 36 OF 155
KM 763 BS 3602-2 430
KM 764 BS 3602-2 490
ASTM-A-213M Seamless Ferritic & Austenitic Alloy Steel Boiler, Superheater & Heat-Exchanger Tubes
KM 765 ASTM-A-213M T2
KM 767 ASTM-A-213M T 5b
KM 768 ASTM-A-213M T 5c
KM 770 ASTM-A-213M T 11
KM 771 ASTM-A-213M T 12
KM 772 ASTM-A-213M T 17
KM 773 ASTM-A-213M T 21
KM 774 ASTM-A-213M T 22
KM 775 ASTM-A-213M T 91
KM 776 ASTM-A-213M T 92
KM 777 ASTM-A-213M 18 Cr-2 Mo
KM 778 ASTM-A-213M TP 304
KM 779 ASTM-A-213M TP 304 H
KM 780 ASTM-A-213M TP 304 N
KM 781 ASTM-A-213M TP 304 LN
KM 782 ASTM-A-213M TP 304 L
KM 783 ASTM-A-213M TP 309 Cb
KM 784 ASTM-A-213M TP 309 HCb
KM 785 ASTM-A-213M TP 309 S
KM 786 ASTM-A-213M TP 310 HCbN
412704185.xls 37 OF 155
KM 791 ASTM-A-213M TP 347 HFG
ASTM-A-106 Seamless Carbon Steel Pipes for High Temperature Service

KM 793 ASTM-A-106 Grade A
KM 794 ASTM-A-106 Grade B
KM 795 ASTM-A-106 Grade C
DIN 17175 Seamless tubes of heat resistant steels

KM 796 DIN 17175 St 35.8 1.0305
KM 797 DIN 17175 St 45.8 1.0405
KM 798 DIN 17175 17 Mn 4 1.0481
KM 799 DIN 17175 19 Mn 5 1.0482
KM 800 DIN 17175 15 Mo 3 1.5415
KM 801 DIN 17175 13 CrMo 4 4 1.7335
KM 802 DIN 17175 10 CrMo 9 10 1.7380
KM 803 DIN 17175 14 MoV 6 3 1.7715
KM 804 DIN 17175 X 20 CrMoV12 1 1.4922
SEW 028 Alloyed & Unalloyed steels for Pressure vessels for moderate elevated temperatures
KM 805 SEW 028 15 NiCuMoNb 5 1.6368
4.8 SPRING STEELS

IS 2507 Cold Rolled Steel Strips for Springs
KM 806 IS 2507 Grade 1 - 45 C 8
KM 807 IS 2507 Grade 2 - 55 C 6
412704185.xls 38 OF 155
KM 808 IS 2507 Grade 3 - 65 C 6
KM 809 IS 2507 Grade 4 - 70 C 6
KM 810 IS 2507 Grade 5 - 75 C 6
KM 811 IS 2507 Grade 6 - 80 C 6
KM 812 IS 2507 Grade 7 - 85 C 6
KM 813 IS 2507 Grade 8 - 98 C 6
KM 814 IS 2507 Grade 9 - 55 Si 7
KM 815 IS 2507 Grade 10 - 50 Cr 4
KM 816 IS 2507 Grade 11- 50 Cr4V2
DIN 17221 Hot Rolled Spring Steels Suitable for Quenching & Tempering
KM 817 DIN 17221 38 Si 7 1.5023
KM 818 DIN 17221 54 SiCr 6 1.7102
KM 819 DIN 17221 60 SiCr 7 1.7108
KM 820 DIN 17221 55 Cr 3 1.7176
KM 821 DIN 17221 50 CrV 4 1.8159
KM 822 DIN 17221 51 CrMoV 4 1.7701
DIN 17222 Cold Rolled Steel Strips for Springs

KM 823 DIN 17222 C 55 1.0535
KM 824 DIN 17222 C 60 1.0601
KM 825 DIN 17222 C 67 1.0603
KM 826 DIN 17222 C 75 1.0605
KM 827 DIN 17222 Ck55 1.1203
KM 828 DIN 17222 Ck 60 1.1221
KM 829 DIN 17222 Ck 67 1.1231
KM 830 DIN 17222 Ck 75 1.1248
KM 831 DIN 17222 Ck 85 1.1269
KM 832 DIN 17222 Ck 101 1.1274
412704185.xls 39 OF 155
KM 833 DIN 17222 55 Si 7 1.0904
KM 834 DIN 17222 71 Si 7 1.5029
KM 835 DIN 17222 67 SiCr 5 1.7103
KM 836 DIN 17222 50 CrV 4 1.8159
BS 970-2 Wrought Steels for Hot Formed Springs for Mechanical & Allied Engineering Purposes
KM 837 BS 970-2 251 A 58
KM 838 BS 970-2 251 A 60
KM 839 BS 970-2 525 A 58
KM 840 BS 970-2 525 A 60
KM 841 BS 970-2 525 A 61
KM 842 BS 970-2 685 A 57
KM 843 BS 970-2 704 A 60
KM 844 BS 970-2 705 A 60
KM 845 BS 970-2 735 A 51
KM 846 BS 970-2 735 A 54
KM 847 BS 970-2 925 A 60
KM 848 BS 970-2 251 H 60
KM 849 BS 970-2 525 H 60
KM 850 BS 970-2 685 H 57
KM 851 BS 970-2 704 H 60
KM 852 BS 970-2 705 H 60
KM 853 BS 970-2 735 H 51
KM 854 BS 970-2 805 H 60
4.9 CASE HARDENING STEELS
412704185.xls 40 OF 155
EN 10084 CASE HARDENING STEELS
KM 901 EN 10084 C10E 1.1121 DIN 17210 Ck 10
KM 902 EN 10084 C15E 1.1141 DIN 17210 C 15
KM 903 EN 10084 C16E 1.1148
KM 904 EN 10084 17Cr3 1.7016 DIN 17210 17 Cr 3
KM 905 EN 10084 28Cr4 1.7030 DIN 17210 20 Cr 4
KM 906 EN 10084 16MnCr5 1.7131 DIN 17210 16 MnCr 5
KM 907 EN 10084 20MnCr5 1.7147 DIN 17210 20 MnCr 5
KM 908 EN 10084 18CrMo4 1.7243
DIN 17210
KM 909 EN 10084 22CrMoS3-5 1.7333 22 CrMoS 3 5
KM 910 EN 10084 20MoCr3 1.7320
DIN 17210
KM 911 EN 10084 20MoCr4 1.7321 20 MoCr 4
KM 912 EN 10084 16NiCr4 1.5714
KM 913 EN 10084 18NiCr5-4 1.5810
KM 914 EN 10084 17CrNi6-6 1.5919 DIN 17210 15 CrNi 6
KM 915 EN 10084 15NiCr13 1.5752
DIN 17210
KM 916 EN 10084 20NiCrMo2-2 1.6523 21 NiCrMo 2
KM 917 EN 10084 17NiCrMo6-4 1.6566
KM 918 EN 10084 20NiCrMoS6-4 1.6571
DIN 17210
KM 919 EN 10084 18CrNiMo7-6 1.6587 17 CrNiMo 6
412704185.xls 41 OF 155
4.10 NON - FERROUS CASTINGS
DIN 1705 Copper-Tin-Zinc Casting Alloys ( Tin Bronze & Gunmetal Castings )
KM 1001 DIN 1705 G-CuSn 12 2.1052.01
KM 1002 DIN 1705 GZ-CuSn 12 2.1052.03
KM 1003 DIN 1705 GC-CuSn 12 2.1052.04
KM 1004 DIN 1705 G-CuSn 12 Ni 2.1060.01 BS 1400-CT 2
KM 1005 DIN 1705 GZ-CuSn 12 Ni 2.1060.03
KM 1006 DIN 1705 GC-CuSn 12 Ni 2.1060.04
KM 1007 DIN 1705 G-CuSn 12 Pb 2.1061.01
KM 1008 DIN 1705 GZ-CuSn 12 Pb 2.1061.03
KM 1009 DIN 1705 GC-CuSn 12 Pb 2.1061.04
KM 1010 DIN 1705 G-CuSn 10 2.1050.01 BS 1400-PB 4
KM 1011 DIN 1705 G-CuSn 10 Zn 2.1086.01 BS 1400- G 1
KM 1012 DIN 1705 G-CuSn 7 ZnPb 2.1090.01
KM 1013 DIN 1705 GZ-CuSn 7 ZnPb 2.1090.03
KM 1014 DIN 1705 GC-CuSn 17 ZnPb 2.1090.04
KM 1015 DIN 1705 G-CuSn 6 ZnNi 2.1093.01 IS 318 - L T B 1
KM 1016 DIN 1705 G-CuSn 5 ZnPb 2.1096.01 IS 318 - L T B 2 BS 1400-LG 2
KM 1017 DIN 1705 G-CuSn 2 ZnPb 2.1098.01
DIN 1709 Copper-Zinc Alloy ( Brass ) Castings

KM 1018 DIN 1709 G-CuZn 15 2.0241.01
KM 1019 DIN 1709 G-CuZn 33 Pb 2.0290.01
KM 1020 DIN 1709 G-CuZn 37 Pb 2.0340.01
KM 1021 DIN 1709 GD-CuZn 37 Pb 2.0340.05
KM 1022 DIN 1709 GK-CuZn 37 Pb 2.0340.02
KM 1023 DIN 1709 G-CuZn 38 Al 2.0591.01
412704185.xls 42 OF 155
KM 1024 DIN 1709 GK-CuZn 38 Al 2.0591.02
KM 1025 DIN 1709 G-CuZn 40 Fe 2.0590.01
KM 1026 DIN 1709 GZ-CuZn 40 Fe 2.0590.03
KM 1027 DIN 1709 GK-CuZn 37 Al 1 2.0595.02
KM 1028 DIN 1709 G-CuZn 35 Al 1 2.0592.01
KM 1029 DIN 1709 GZ-CuZn 35 Al 1 2.0592.03
KM 1030 DIN 1709 GK-CuZn 35 Al 1 2.0592.02
KM 1031 DIN 1709 G-CuZn 34 Al 2 2.0596.01
KM 1032 DIN 1709 GZ-CuZn 34 Al 2 2.0596.03
KM 1033 DIN 1709 GK-CuZn 34 Al 2 2.0596.02
KM 1034 DIN 1709 G-CuZn 25 Al 5 2.0598.01
KM 1035 DIN 1709 GZ-CuZn 25 Al 5 2.0598.03
KM 1036 DIN 1709 GK-CuZn 25 Al 5 2.0598.02
KM 1037 DIN 1709 G-CuZn 15 Si 4 2.0492.01
KM 1038 DIN 1709 GD-CuZn 15 Si 4 2.0492.05
KM 1039 DIN 1709 GK-CuZn 15 Si 4 2.0492.02
DIN 1714 Copper-Aluminium Casting Alloys ( Aluminium Bronze Castings )

KM 1040 DIN 1714 G-CuAl 10 Fe 2.0940.01
KM 1041 DIN 1714 GK-CuAl 10 Fe 2.0940.02
KM 1042 DIN 1714 GZ-CuAl 10 Fe 2.0940.03
KM 1043 DIN 1714 G-CuAl 9 Ni 2.0970.01
KM 1044 DIN 1714 GK-CuAl 9 Ni 2.0970.02
KM 1045 DIN 1714 GZ-CuAl 9 Ni 2.0970.03
KM 1046 DIN 1714 G-CuAl 10 Ni 2.0975.01
KM 1047 DIN 1714 GK-CuAl 10 Ni 2.0975.02
KM 1048 DIN 1714 GZ-CuAl 10 Ni 2.0975.03
KM 1049 DIN 1714 GC-CuAl 10 Ni 2.0975.04
KM 1050 DIN 1714 G-CuAl 11 Ni 2.0980.01
412704185.xls 43 OF 155
KM 1051 DIN 1714 GK-CuAl 11 Ni 2.0980.02
KM 1052 DIN 1714 GZ-CuAl 11 Ni 2.0980.03
KM 1053 DIN 1714 G-CuAl 8 Mn 2.0962.01
KM 1054 DIN 1714 GK-CuAl 8 Mn 2.0962.02
IS 318 Leaded Tin Bronze Ingots and Castings

KM 1055 IS 318 LTB 1 DIN 1705 G-CuSn6ZnNi
KM 1056 IS 318 LTB 2 DIN 1705 G-CuSn5ZnPb BS 1400-LG2
KM 1057 IS 318 LTB 3
KM 1058 IS 318 LTB 4
KM 1059 IS 318 LTB 5 BS 1400-LB2
KM 1060 IS 318 LTB 6 BS 1400-LB5
IS 305 Aluminium Bronze Ingots and Castings

KM 1061 IS 305 GRADE AB 1 Aluminium Bronze Castings
KM 1062 IS 305 GRADE AB 2 Aluminium Bronze Castings
IS 306 Tin Bronze Ingots and Castings

KM 1063 IS 306 Ingots Tin Bronze Ingots
KM 1064 IS 306 Castings Tin Bronze Castings
IS 25 Antifriction Bearing Alloys

KM 1065 IS 25 GRADE 90
412704185.xls 44 OF 155
BS 1400 Copper & Copper Alloy Ingots & Castings
KM 1075 BS 1400 Cu Sn10 Pb P PB4 DIN 1705-G CuSn 10 Phosphor Bronze

KM 1076 BS 1400 Cu Sn7 Pb P LPB1 Leaded Phosphor Bronze
KM 1077 BS 1400 Cu Sn10 Pb10 LB2 IS 318 - LTB 5 Leaded Bronze
KM 1078 BS 1400 Cu Sn5 Pb9 LB4 Leaded Bronze
KM 1079 BS 1400 Cu Sn3 Pb5 Zn8 LG1 Leaded Gun metal
KM 1080 BS 1400 Cu Sn5 Pb5 Zn5 LG2 IS 318 - LTB 2 DIN 1705-GCuSn5ZnPb Leaded Gun metal
KM 1081 BS 1400 Cu Zn25 Pb3 Sn2 SCB1 Brass for sand castings
KM 1082 BS 1400 Cu Zn33 Pb2 SCB3 Brass for sand castings
KM 1083 BS 1400 Cu Zn15 As SCB6 Brass for brazeable castings
KM 1084 BS 1400 Cu Zn40 DCB1 Brass for die castings
KM 1085 BS 1400 Cu Zn40 Pb DCB3 Brass for die castings
KM 1086 BS 1400 Cu Zn40 Pb PCB1 Brass for pressure die castings
KM 1087 BS 1400 - HCC1 High Conductivity Copper
KM 1088 BS 1400 Cu Cr1 CC1-TF Copper Chromium
KM 1089 BS 1400 Cu Sn10 P PB1 Phosphor Bronze
KM 1090 BS 1400 Cu Sn11 P PB2 Phosphor Bronze
KM 1091 BS 1400 Cu Sn10 CT1 Copper Tin
KM 1092 BS 1400 Cu Sn7 Pb3 Zn3 LG4 Leaded Gun metal
KM 1093 BS 1400 Cu Al10 Fe3 AB1 Aluminium Bronze
KM 1094 BS 1400 Cu Al10 Fe5 Ni5 AB2 Aluminium Bronze
412704185.xls 45 OF 155
KM 1095 BS 1400 Cu Mn13 Al8 Fe3 Ni3 CMA1 Copper Manganese Aluminium
KM 1096 BS 1400 Cu Zn35 Al Fe Mn HTB1 High tensile Brass
KM 1097 BS 1400 Cu Zn28 Al15 Fe Mn HTB3 High tensile Beta Brass
KM 1098 BS 1400 Cu Pb15 Sn9 LB1 Leaded Bronze
KM 1099 BS 1400 Cu Pb20 Sn5 LB5 IS 318 - LTB 6 DIN 1705-GCuSn10Zn Leaded Bronze
KM 1100 BS 1400 Cu Pb10 Zn2 G1 Gun metal
KM 1101 BS 1400 Cu Sn7 Ni5 Zn3 G3 Nickel Gun metal
KM 1102 BS 1400 Cu Sn7 Ni5 Zn3 G3-TF Ni Gun metal Fully heat treated
KM 1103 BS 1400 Cu Zn36 Sn SCB4 Naval Brass for sand casting
KM 1104 BS 1400 Cu Sn12 Ni CT2 DIN 1705-GCuSn12Ni Copper Tin
KM 1105 BS 1400 Cu Al6 Si2 Fe AB3 Aluminium Silicon Bronze
KM 1106 BS 1400 Cu Ni30 Cr CN1 Copper Nickel Chromium
KM 1107 BS 1400 Cu Ni30 Nb CN2 Copper Nickel Niobium
412704185.xls 46 OF 155
Division 5. CHEMICAL AND MECHANICAL PROPERTIES Rev. 0
MATL STANDARD CHEMICAL COMPOSITION MECHANICAL PROPERTIES

No. GRADE % C % Mn % Si % S % P % Cr % Mo % Ni OTHERS UTS YS ELONG IMPACT HDN LRS
DESIGNATION max max max max max max max max N/mm2 N/mm2 % J(ISO-V) BHN mm
min min min min min max
IS 2062 Steel for General Structural Purposes
KM 101 Grade A 0.23 1.5 0.1 min 0.05 0.05 - - - Nb,V,Ti,Cu 410 250 23 - - 20
KM 102 Grade B 0.22 1.5 0.4 0.045 0.045 - - - " 410 250 23 27 - 20
KM 103 Grade C 0.20 1.5 0.4 0.04 0.04 - - - " 410 250 23 27 - 20
IS 1570-1 Schedules for wrought steels specified by Tensile or Yield Strength properties.
KM 104 Fe 290 NOT SPECIFIED AS PER QUALITY L - - - - 290 170 27 - - -
KM 105 FeE 220 NOT SPECIFIED AS PER QUALITY L - - - - 290 220 27 - - -
IS 1079 Hot rolled carbon steel sheets & strips

KM 126 Gr O - - - 0.06 0.06 Cu - - - - - -
KM 127 Gr D 0.12 0.5 0.1 min 0.05 0.05 Cu 260 - - - - -
KM 128 Gr DD 0.1 0.5 0.1 min 0.04 0.04 Cu 260-390 - 23 - - -
KM 129 Gr EDD 0.1 0.45 0.1 min 0.035 0.035 Cu 260-380 - 25 - - -
KM 130 Gr St 34 0.15 - 0.1 min 0.05 0.05 Cu 330-410 205 25 - - -
KM 131 Gr St 42 0.25 - 0.1 min 0.05 0.05 Cu 410-490 235 22 - - -
KM 132 Gr St 50 0.3 - 0.1 min 0.05 0.05 Cu 490-590 295 20 - - -
KM 133 Gr St 52 0.25 - 0.1 min 0.05 0.05 Cu 510-610 355 20 - - -
IS 513 Cold rolled low carbon steel sheets & strips

KM 134 Gr O 0.15 0.6 - 0.055 0.055 - - - - - - - - ** 79 -
KM 135 Gr D 0.12 0.5 - 0.04 0.04 - - - - 270-410 280 max * 28 - ** 60 -
KM 136 Gr DD 0.1 0.45 - 0.035 0.035 - - - - 270-370 250 * 32 - ** 55 -
KM 137 Gr EDD 0.08 0.4 - 0.03 0.03 - - - - 270-350 220 * 36 - ** 50 -
* - % Elongation in a gauge length of 80 mm.

** - Max hardness in HR ( 30 T ) scale.
EN 10025 Hot Rolled Products of non alloyed Structural Steels

KM 138 S185 - - - - - - - - - 310-540 185 18 - - 3
KM 139 S235JR 0.17 1.4 - 0.045 0.045 - - - N=0.009 360-510 235 26 27at+20C - 3
KM 140 S235JRG1 0.17 1.4 - 0.045 0.045 - - - N=0.007 360-510 235 26 27at+20C - 3
KM 141 S235JRG2 0.17 1.4 - 0.045 0.045 - - - N=0.009 360-510 235 26 27at+20C - 3
KM 142 S235J0 0.17 1.4 - 0.04 0.04 - - - N=0.009 360-510 235 26 27 at 0C - 3
KM 143 S235J2G3 0.17 1.4 - 0.035 0.035 - - - - 360-510 235 26 27at-20C - 3
KM 144 S235J2G4 0.17 1.4 - 0.035 0.035 - - - - 360-510 235 24 27at-20C - 3
KM 145 S275JR 0.21 1.5 - 0.045 0.045 - - - N=0.009 430-580 275 22 27at+20C - 3
KM 146 S275J0 0.18 1.5 - 0.04 0.04 - - - N=0.009 430-580 275 22 27 at 0C - 3
KM 147 S275J2G3 0.18 1.5 - 0.035 0.035 - - - - 430-580 275 22 27at-20C - 3
KM 148 S275J2G4 0.18 1.5 - 0.035 0.035 - - - - 430-580 275 20 27at-20C - 3
KM 149 S355JR 0.24 1.6 0.55 0.045 0.045 - - - N=0.009 510-680 355 22 27at+20C - 3
KM 150 S355J0 0.2 1.6 0.55 0.04 0.04 - - - N=0.009 510-680 355 22 27 at 0C - 3
KM 151 S355J2G3 0.2 1.6 0.55 0.035 0.035 - - - - 510-680 355 22 27at-20C - 3
KM 152 S355J2G4 0.2 1.6 0.55 0.035 0.035 - - - - 510-680 355 22 27at-20C - 3
KM 153 S355K2G3 0.2 1.6 0.55 0.035 0.035 - - - - 510-680 355 22 40at-20C - 3
KM 154 S355K2G4 0.2 1.6 0.55 0.035 0.035 - - - - 510-680 355 20 40at-20C - 3
KM 155 E 295 - - - 0.045 0.045 - - - N=0.009 490-660 295 20 - - 3
KM 156 E 335 - - - 0.045 0.045 - - - N=0.009 590-770 335 16 - - 3
KM 157 E 360 - - - 0.045 0.045 - - - N=0.009 690-900 3650 11 - - 3
ASTM-A-36M Structural Carbon Steel

KM 158 ASTM-A-36M 0.25 - 0.4 0.05 0.04 - - - Cu > 0.2 ** 400-550 250 23 - - 20
** - Minimum Cu when Copper steel is specified
ASTM-A-283M Low and Intermediate tensile strength Carbon steel plates

KM 159 Grade A 0.14 0.9 0.4 0.04 0.035 - - - Cu > 0.2 ** 310-415 165 30 - - -
KM 160 Grade B 0.17 0.9 0.4 0.04 0.035 - - - Cu > 0.2 ** 345-450 185 28 - - -
KM 161 Grade C 0.24 0.9 0.4 0.04 0.035 - - - Cu > 0.2 ** 380-515 205 25 - - -
KM 162 Grade D 0.27 0.9 0.4 0.04 0.035 - - - Cu > 0.2 ** 415-550 230 23 - - -
ASTM-A-285M Low and Intermediate strength carbon steel plates for Pressure Vessels
KM 163 Grade A 0.17 0.9 - 0.035 0.035 - - - - 310-450 165 30 - - -
KM 164 Grade B 0.22 0.9 - 0.035 0.035 - - - - 345-485 185 28 - - -
KM 165 Grade C 0.28 0.9 - 0.035 0.035 - - - - 380-515 205 27 - - -
ASTM-A-299M Carbon steel plates for Pressure Vessels

KM 166 ASTM-A-299M 0.28 0.9-1.4 0.15-0.4 0.035 0.035 - - - - 515-655 290 19 - - 25
ASTM-A-366M Cold rolled , Commercial quality Carbon steel sheets

KM 167 ASTM-A-366M 0.15 0.6 - 0.035 0.030 - - - Cu > 0.2 ** - - - - - -
ASTM-A-387M Chromium - Molybdenum alloy steel Pressure vessel plates.

KM 168 Grade 2 0.05-0.21 0.55-0.8 0.15-0.4 0.035 0.035 0.5-0.8 0.45-0.6 - - 380-550 230 22 - - Class 1
485-620 310 22 - - Class 2
KM 169 Grade 12 0.05-0.17 0.4-0.65 0.15-0.4 0.035 0.035 0.8-1.15 0.45-0.6 - - 380-550 230 22 - - Class 1
450-585 275 22 - - Class 2
KM 170 Grade 11 0.05-0.17 0.4-0.65 0.5-0.8 0.035 0.035 1.0-1.5 0.45-0.65 - - 415-585 240 22 - - Class 1
515-690 310 22 - - Class 2
KM 171 Grade 22 0.05-0.15 0.3-0.6 0.5 0.035 0.035 2.0-2.5 0.9-1.1 - - 415-585 210 18 - - Class 1
515-690 310 18 - - Class 2
KM 172 Grade 21 0.05-0.15 0.3-0.6 0.5 0.035 0.035 2.75-3.25 0.9-1.1 - - 415-585 210 18 - - Class 1
515-690 310 18 - - Class 2
KM 173 Grade 5 0.15 0.3-0.6 0.5 0.03 0.035 4.0-6.0 0.45-0.65 - - 415-585 210 18 - - Class 1
515-690 310 18 - - Class 2
KM 174 Grade 9 0.15 0.3-0.6 1.0 0.03 0.03 8.0-10.0 0.9-1.1 - - 415-585 210 18 - - Class 1
515-690 310 18 - - Class 2
V=0.18-0.25,
Cb=0.06-0.1,
N=0.03-0.07,
KM 175 Grade 91 0.08-0.12 0.3-0.6 0.2-0.5 0.01 0.02 8.0-9.5 0.85-1.05 0.4 Al<0.04 585-760 415 18 - - Class 2
ASTM-A-569M Hot Rolled, Commercial quality Carbon steel sheet and strip
KM 176 Type A 0.1 0.6 - 0.035 0.03 0.15 0.06 0.2 V,Cb,Ti < 0.008 - 205-345 25 - - -
KM 177 Type B 0.02-0.15 0.6 - 0.035 0.03 0.15 0.06 0.2 V,Cb,Ti < 0.008 - 205-345 25 - - -
KM 178 Type C 0.08 0.6 - 0.035 0.1 0.15 0.06 0.2 V,Cb,Ti < 0.008 - 205-345 25 - - -
ASTM-A-573M Structural Carbon Steel Plates with improved toughness

KM 179 Grade 58 0.23 0.6-0.9 0.1-0.35 0.04 0.035 - - - - 400-490 220 24 - - -
KM 180 Grade 65 0.24 0.85-1.2 0.15-0.4 0.04 0.035 - - - - 450-530 240 23 - - -
KM 181 Grade 70 0.27 0.85-1.2 0.15-0.4 0.04 0.035 - - - - 485-620 290 21 - - -
ASTM-A-612M High Strength, Carbon Steel, Pressure Vessel Plates for Moderate & Low Temperature Service
KM 182 ASTM-A 612 0.25 1.0-1.35 0.15-0.4 0.035 0.035 0.25 0.08 0.25 Cu<0.35,V<0.08 560-695 345 22 - - 25
EN 10028-3 Weldable, Normalised, Fine Grained Steel Flat Products for Pressure Purposes
N<0.02,Al>0.02,
V,Nb<0.05,
KM 183 P275N 0.18 0.5-1.4 0.4 0.025 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 390-510 275 24 40 - < 16
N<0.02,Al>0.02,
V,Nb<0.05,
KM 184 P275NH 0.18 0.5-1.4 0.4 0.025 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 390-510 275 24 40 - < 16
N<0.02,Al>0.02,
V,Nb<0.05,
KM 185 P275NL1 0.16 0.5-1.5 0.4 0.02 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 390-510 275 24 47 - < 16
N<0.02,Al>0.02,
V,Nb<0.05,
KM 186 P275NL2 0.16 0.5-1.5 0.4 0.015 0.025 0.3 0.08 0.5 Cu<0.3,Ti<0.03 390-510 275 24 65 - < 16
V<0.1,Nb<0.05,
KM 187 P355N 0.20 0.9-1.7 0.5 0.025 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 490-630 355 22 40 - < 16
V<0.1,Nb<0.05,
KM 188 P355NH 0.20 0.9-1.7 0.5 0.025 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 490-630 355 22 40 - < 16
V<0.1,Nb<0.05,
KM 189 P355NL1 0.18 0.9-1.7 0.5 0.02 0.03 0.3 0.08 0.5 Cu<0.3,Ti<0.03 490-630 355 22 47 - < 16
V<0.1,Nb<0.05,
KM 190 P355NL2 0.18 0.9-1.7 0.5 0.015 0.025 0.3 0.08 0.5 Cu<0.3,Ti<0.03 490-630 355 22 65 - < 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 191 P460N 0.20 1.0-1.7 0.6 0.025 0.03 0.3 0.1 0.8 Cu<0.7,Ti<0.03 570-720 460 17 40 - < 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 192 P460NH 0.20 1.0-1.7 0.6 0.025 0.03 0.3 0.1 0.8 Cu<0.7,Ti<0.03 570-720 460 17 40 - < 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 193 P460NL1 0.20 1.0-1.7 0.6 0.02 0.03 0.3 0.1 0.8 Cu<0.7,Ti<0.03 570-720 460 17 47 - < 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 194 P460NL2 0.20 1.0-1.7 0.6 0.015 0.025 0.3 0.1 0.8 Cu<0.7,Ti<0.03 570-720 460 17 65 - < 16
EN 10113-2 Hot Rolled Products from Weldable, Fine Grain, Normalised Structural Steel
N<0.015,Al>0.02
V,Nb<0.05,
KM 195 S275N 0.18 0.5-1.4 0.4 0.03 0.035 0.3 0.1 0.3 Cu<0.35,Ti<0.03 370-510 275 24 55 - 16
N<0.015,Al>0.02
V,Nb<0.05,
KM 196 S275NL 0.16 0.5-1.4 0.4 0.025 0.03 0.3 0.1 0.3 Cu<0.35,Ti<0.03 370-510 275 24 63 - 16
N<0.015,Al>0.02
V<0.12,Nb<0.05,
KM 197 S355N 0.2 0.9-1.65 0.5 0.03 0.035 0.3 0.1 0.5 Cu<0.35,Ti<0.03 470-630 355 22 55 - 16
N<0.015,Al>0.02
V<0.12,Nb<0.05,
KM 198 S355NL 0.18 0.9-1.65 0.5 0.025 0.03 0.3 0.1 0.5 Cu<0.35,Ti<0.03 470-630 355 22 63 - 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 199 S460N 0.2 1.0-1.7 0.6 0.03 0.035 0.3 0.1 0.8 Cu<0.7,Ti<0.03 550-720 460 17 55 - 16
N<0.025,Al>0.02
V<0.2,Nb<0.05,
KM 200 S460NL 0.2 1.0-1.7 0.6 0.025 0.03 0.3 0.1 0.8 Cu<0.7,Ti<0.03 550-720 460 17 63 - 16
IS 1570 Wrought Carbon Steel Schedules

KM 201 20 C 8 0.15-0.25 0.6-0.9 - AS AGREED - - 440-520 - 24 - - -
KM 202 25 C 4 0.2-0.3 0.3-0.6 - AS AGREED - - 440-540 - 23 - - -
KM 203 25 C 8 0.2-0.3 0.6-0.9 - AS AGREED - - 470-570 - 22 - - -
KM 204 30 C 8 0.25-0.35 0.6-0.9 - AS AGREED - - 500-600 - 21 - - -
KM 205 35 C 4 0.3-0.4 0.3-0.6 - AS AGREED - - 520-620 - 20 - - -
KM 206 35 C 8 0.3-0.4 0.6-0.9 - AS AGREED - - 550-650 - 20 - - -
KM 207 40 C 8 0.35-0.45 0.6-0.9 - AS AGREED - - 580-680 - 18 - - -
KM 208 45 C 8 0.4-0.5 0.6-0.9 - AS AGREED - - 630-710 - 15 - - -
KM 209 50 C 4 0.45-0.55 0.3-0.6 - AS AGREED - - 660-780 - 13 - - -
KM 210 50 C 8 0.45-0.55 0.6-0.9 - AS AGREED - - - - - - - -
KM 211 55 C 4 0.5-0.6 0.3-0.6 - AS AGREED - - - - - - - -
KM 212 55 C 8 0.5-0.6 0.6-0.9 - AS AGREED - - 720 - 13 - - -
KM 213 60 C 4 0.55-0.65 0.3-0.6 - AS AGREED - - 750 - 11 - - -
KM 214 60 C 8 0.55-0.65 0.5-0.8 - AS AGREED - - - - - - - -
IS 1875 Carbon Steel Billets, Blooms, Slabs, & Bars for Forgings
KM 215 14 C 6 0.10-0.18 0.4-0.7 0.15-0.35 0.04 0.04 - 370 200 26 100 - < 100
KM 216 15 C 8 0.10-0.20 0.6-0.9 0.15-0.35 0.03 0.04 - 410 220 25 110 - < 100
KM 217 20 C 8 0.15-0.25 0.6-0.9 0.15-0.35 0.04 0.04 - 430 230 24 120 - < 100
KM 218 25 C 8 0.2-0.3 0.6-0.9 0.15-0.35 0.04 0.04 - 460 250 22 130 - < 100
KM 219 30 C 8 0.25-0.35 0.6-0.9 0.15-0.35 0.04 0.04 - 490 270 21 140 - < 100
KM 220 35 C 8 0.3-0.4 0.6-0.9 0.15-0.35 0.04 0.04 - 540 280 20 155 - < 100
KM 221 45 C 8 0.4-0.5 0.6-0.9 0.15-0.35 0.04 0.04 - 620 320 15 175 - < 100
KM 222 55 C 8 0.5-0.6 0.6-0.9 0.15-0.35 0.04 0.04 - 710 350 13 200 - < 100
KM 223 65 C 6 0.6-0.7 0.5-0.8 0.15-0.35 0.04 0.04 - 740 370 10 210 - < 100
BS 970-3 Wrought Steels for Mechanical & Allied Engineering Purposes

KM 224 080 M 40 (En8) 0.36-0.44 0.6-1.0 0.1-0.4 0.05 0.05 550 280 16 16 152-207 6-150
KM 225 070 M 55 (En9) 0.5-0.6 0.5-0.9 0.1-0.4 0.05 0.05 700 355 12 - 201-255 6-63
KM 226 709 M 40 (En19) 0.36-0.44 0.7-1.0 0.1-0.4 0.04 0.035 0.9 -1.2 0.25-0.35 1000-1150 850 12 42 293-352 6-29
KM 227 817 M 40 (En24) 0.36-0.44 0.45-0.7 0.1-0.4 0.04 0.035 1.0-1.4 0.2-0.35 1.3-1.7 1150-1300 1020 10 28 341-401 6-29
EN 10083 Quenched & Tempered Unalloyed Quality Steels

KM 228 C22 0.17-0.24 0.4-0.7 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 410 210 25 - - 16-100
KM 229 C22E 0.17-0.24 0.4-0.7 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 410 210 25 - - 16-100
KM 230 C22R 0.17-0.24 0.4-0.7 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 410 210 25 - - 16-100
KM 231 C25 0.22-0.29 0.4-0.7 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 440 230 23 - - 16-100
KM 232 C25E 0.22-0.29 0.4-0.7 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 440 230 23 - - 16-100
KM 233 C25R 0.22-0.29 0.4-0.7 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 440 230 23 - - 16-100
KM 234 C30 0.27-0.34 0.5-0.8 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 480 250 21 - - 16-100
KM 235 C30E 0.27-0.34 0.5-0.8 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 480 250 21 - - 16-100
KM 236 C30R 0.27-0.34 0.5-0.8 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 480 250 21 - - 16-100
KM 237 C35 0.32-0.39 0.5-0.8 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 520 270 19 - - 16-100
KM 238 C35E 0.32-0.39 0.5-0.8 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 520 270 19 - - 16-100
KM 239 C35R 0.32-0.39 0.5-0.8 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 520 270 19 - - 16-100
KM 240 C40 0.37-0.44 0.5-0.8 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 550 290 17 - - 16-100
KM 241 C40E 0.37-0.44 0.5-0.8 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 550 290 17 - - 16-100
KM 242 C40R 0.37-0.44 0.5-0.8 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 550 290 17 - - 16-100
KM 243 C45 0.42-0.5 0.5-0.8 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 580 305 16 - - 16-100
KM 244 C45E 0.42-0.5 0.5-0.8 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 580 305 16 - - 16-100
KM 245 C45R 0.42-0.5 0.5-0.8 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 580 305 16 - - 16-100
KM 246 C50 0.47-0.55 0.6-0.9 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 610 320 14 - - 16-100
KM 247 C50E 0.47-0.55 0.6-0.9 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 610 320 14 - - 16-100
KM 248 C50R 0.47-0.55 0.6-0.9 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 610 320 14 - - 16-100
KM 249 C55 0.52-0.6 0.6-0.9 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 640 330 12 - - 16-100
KM 250 C55E 0.52-0.6 0.6-0.9 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 640 330 12 - - 16-100
KM 251 C55R 0.52-0.6 0.6-0.9 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 640 330 12 - - 16-100
KM 252 C60 0.57-0.65 0.6-0.9 0.4 0.045 0.045 0.4 0.1 0.4 Cr+Mo+Ni<0.63 670 340 11 - - 16-100
KM 253 C60E 0.57-0.65 0.6-0.9 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 670 340 11 - - 16-100
KM 254 C60R 0.57-0.65 0.6-0.9 0.4 0.02-0.04 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 670 340 11 - - 16-100
KM 255 28Mn6 0.25-0.32 1.3-1.65 0.4 0.035 0.035 0.4 0.1 0.4 Cr+Mo+Ni<0.63 600 310 18 - - 16-100

EN 10083-1 Quenched & Tempered Special Steels
KM 256 38Cr2 0.35-0.42 0.5-0.8 0.4 0.035 0.035 0.4-0.6 - - - 700-850 450 15 35 - 16-40
KM 257 46Cr2 0.42-0.50 0.5-0.8 0.4 0.035 0.035 0.4-0.6 - - - 800-950 550 14 35 - 16-40
KM 258 34Cr4 0.3-0.37 0.6-0.9 0.4 0.035 0.035 0.9-1.2 - - - 800-950 590 14 40 - 16-40
KM 259 37Cr4 0.34-0.41 0.6-0.9 0.4 0.035 0.035 0.9-1.2 - - - 850-1000 630 13 35 - 16-40
KM 260 41Cr4 0.38-0.45 0.6-0.9 0.4 0.035 0.035 0.9-1.2 - - - 900-1100 660 12 35 - 16-40
KM 261 25CrMo4 0.22-0.29 0.6-0.9 0.4 0.035 0.035 0.9-1.2 0.15-0.3 - - 800-950 600 14 50 - 16-40
KM 262 34CrMo4 0.3-0.37 0.6-0.9 0.4 0.035 0.035 0.9-1.2 0.15-0.3 - - 900-1100 650 12 40 - 16-40
KM 263 42CrMo4 0.38-0.45 0.6-0.9 0.4 0.035 0.035 0.9-1.2 0.15-0.3 - - 1000-1200 750 11 35 - 16-40
KM 264 42CrMoS4 0.38-0.45 0.6-0.9 0.4 0.02-0.04 0.035 0.9-1.2 0.15-0.3 - - 1000-1200 750 11 35 - 16-40
KM 265 50CrMo4 0.46-0.54 0.5-0.8 0.4 0.035 0.035 0.9-1.2 0.15-0.3 - - 1000-1200 780 10 30 - 16-40
KM 266 36CrNiMo4 0.32-0.4 0.5-0.8 0.4 0.035 0.035 0.9-1.2 0.15-0.3 0.9-1.2 - 1000-1200 800 11 40 - 16-40
KM 267 34CrNiMo6 0.3-0.38 0.4-0.7 0.4 0.035 0.035 1.4-1.7 0.15-0.3 1.4-1.7 - 1100-1300 900 10 45 - 16-40
KM 268 30CrNiMo8 0.26-0.34 0.3-0.6 0.4 0.035 0.035 1.8-2.2 0.3-0.5 1.8-2.2 - 1250-1450 1050 9 30 - 16-40
KM 269 36NiCrMo16 0.32-0.39 0.3-0.6 0.4 0.025 0.03 1.6-2.0 0.25-0.45 3.6-4.1 - 1250-1450 1050 9 30 - 16-40
KM 270 51CrV4 0.47-0.55 0.7-1.1 0.4 0.035 0.035 0.9-1.2 - - V=0.1-0.2 1000-1200 800 10 30 - 16-40
ASTM-A-108 Cold Finished , Standard quality Carbon Steel bars

KM 271 1010 0.08-0.13 0.3-0.6 - 0.05 0.04 - - - - - - - - - -
KM 272 1015 0.13-0.18 0.3-0.6 - 0.05 0.04 - - - - - - - - - -
KM 273 1020 0.18-0.23 0.3-0.6 - 0.05 0.04 - - - - - - - - - -
KM 274 1025 0.22-0.28 0.3-0.6 - 0.05 0.04 - - - - - - - - - -
KM 275 1030 0.28-0.34 0.6-0.9 - 0.05 0.04 - - - - - - - - - -
KM 276 1035 0.32-0.38 0.6-0.9 - 0.05 0.04 - - - - - - - - - -
KM 277 1040 0.37-0.44 0.6-0.9 - 0.05 0.04 - - - - - - - - - -
KM 278 1045 0.43-0.50 0.6-0.9 - 0.05 0.04 - - - - - - - - - -
KM 279 1050 0.48-0.55 0.6-0.9 - 0.05 0.04 - - - - - - - - - -
KM 280 1118 0.14-0.20 1.3-1.6 - 0.08-0.13 0.04 - - - - - - - - - -
KM 281 1141 0.37-0.45 1.35-1.65 - 0.08-0.13 0.04 - - - - - - - - - -
KM 282 1211 0.13 0.6-0.9 - 0.1-0.15 0.07-0.12 - - - - - - - - - -
KM 283 1215 0.09 0.75-1.05 - 0.26-0.35 0.04-0.09 - - - - - - - - - -
ASTM-A-322 Standard grades of Alloy Steel bars
KM 284 1330 0.28-0.33 1.6-1.9 0.15-0.35 0.04 0.035 - - - - - - - - - -
KM 285 1340 0.38-0.43 1.6-1.9 0.15-0.35 0.04 0.035 - - - - - - - - - -
KM 286 4023 0.2-0.25 0.7-0.9 0.15-0.35 0.04 0.035 - 0.2-0.3 - - - - - - - -
KM 287 4047 0.45-0.50 0.7-0.9 0.15-0.35 0.04 0.035 - 0.2-0.3 - - - - - - - -
KM 288 4130 0.28-0.33 0.4-0.6 0.15-0.35 0.04 0.035 0.8-1.1 0.15-0.25 - - - - - - - -
KM 289 4140 0.38-0.43 0.75-1.0 0.15-0.35 0.04 0.035 0.8-1.1 0.15-0.25 - - - - - - - -
KM 290 4320 0.17-0.22 0.45-0.65 0.15-0.35 0.04 0.035 0.4-0.6 0.2-0.3 1.65-2.0 - - - - - - -
KM 291 4615 0.13-0.18 0.45-0.65 0.15-0.35 0.04 0.035 - 0.2-0.3 1.65-2.0 - - - - - - -
KM 292 4720 0.17-0.22 0.5-0.7 0.15-0.35 0.04 0.035 0.35-0.55 0.15-0.25 0.9-1.2 - - - - - - -
KM 293 4815 0.13-0.18 0.4-0.6 0.15-0.35 0.04 0.035 - 0.2-0.3 3.25-3.75 - - - - - - -
KM 294 5120 0.17-0.22 0.7-0.9 0.15-0.35 0.04 0.035 0.7-0.9 - - - - - - - - -
KM 295 5140 0.38-0.43 0.7-0.9 0.15-0.35 0.04 0.035 0.7-0.9 - - - - - - - - -
KM 296 6150 0.48-0.53 0.7-0.9 0.15-0.35 0.04 0.035 0.8-1.1 - - V > 0.15 - - - - - -
KM 297 8640 0.38-0.43 0.75-1.0 0.15-0.35 0.04 0.035 0.4-0.6 0.15-0.25 0.4-0.7 - - - - - - -
KM 298 8645 0.43-0.48 0.75-1.0 0.15-0.35 0.04 0.035 0.4-0.6 0.15-0.25 0.4-0.7 - - - - - - -
KM 299 8720 0.18-0.23 0.7-0.9 0.15-0.35 0.04 0.035 0.4-0.6 0.2-0.3 0.4-0.7 - - - - - - -
KM 300 9260 0.56-0.64 0.75-1.0 1.8-2.2 0.04 0.035 - - - - - - - - - -
5.3 CAST STEELS

IS 276 Austenitic Manganese Steel Castings
KM 301 Grade 1 1.05-1.35 11.0-14.0 1.0 0.05 0.09 - - - - - - - - 229 max -
KM 302 Grade 2 0.9-1.05 11.5-14.0 1.0 0.05 0.09 - - - - - - - - 229 max -
KM 303 Grade 3 1.05-1.35 11.5-14.0 1.0 0.05 0.09 1.5-2.5 - - - - - - - 229 max -
KM 304 Grade 4 0.7-1.3 11.5-14.0 1.0 0.05 0.09 - - 3.0-5.0 - - - - - - -
KM 305 Grade 5 1.05-1.45 11.5-14.0 1.0 0.05 0.09 - 1.8-2.1 - - - - - - - -
IS 1030 Carbon Steel Castings for General Engineering Purposes

KM 306 200-400 N - - - 0.04 0.045 - - - - 400 200 25 30 * - -
KM 307 200-400 W 0.25 1.0 0.6 0.035 0.04 0.35 0.15 0.4 0.05/ 0.4 400 200 25 40 * - -
KM 308 230-450 N - - - 0.04 0.045 - - - - 450 230 22 25 * - -
KM 309 230-450 W 0.25 1.2 0.6 0.035 0.04 0.35 0.15 0.4 0.05/ 0.4 450 230 22 35 * - -
KM 310 280-520 N - - - 0.04 0.045 - - - - 520 280 18 22 * - -
KM 311 280-520 W 0.25 1.2 0.6 0.035 0.04 0.35 0.15 0.4 0.05/ 0.4 520 280 18 22 * - -
KM 312 340-570 N - - - 0.04 0.045 - - - - 570 340 15 20 * - -
KM 313 340-570 W 0.25 1.5 0.6 0.035 0.04 0.35 0.15 0.4 0.05/ 0.4 570 340 15 20 * - -
IS 2644 High Strength Steel Castings for General Engineering & Structural Purposes
KM 314 CS 640 - - 0.6 0.035 0.035 - - - - 640 390 15 25 * 190 -
KM 315 CS 700 - - 0.6 0.035 0.035 - - - - 700 580 14 25 * 207 -
KM 316 CS 840 - - 0.6 0.035 0.035 - - - - 840 700 12 20 * 248 -
KM 317 CS 1030 - - 0.6 0.035 0.035 - - - - 1030 850 8 15 * 305 -
KM 318 CS 1230 - - 0.6 0.035 0.035 - - - - 1230 1000 5 - 355 -
IS 2707 Carbon Steel Castings for Surface Hardening

KM 319 IS 2707-Gr 1 0.42-0.48 1.0 0.6 0.04 0.04 0.25 0.15 0.4 Cu = 0.3 620 320 12 - - -
KM 320 IS 2707 Gr 2 0.39-0.45 1-1.4 0.3-0.8 0.04 0.04 0.25 0.15 0.4 Cu = 0.3 690 490 12 - - -
KM 321 IS 2707 Gr 3 0.52-0.58 1.0 0.6 0.04 0.04 0.25 0.15 0.4 Cu = 0.3 700 370 8 - - -
IS 2708 1.5 % Manganese Steel Castings for General Engineering Purposes

KM 322 IS 2708-Gr 1 0.18-0.25 1.2-1.6 0.6 0.05 0.05 0.3 0.25 0.4 Cu = 0.3 520 320 16 30 152-207 -
KM 323 IS 2708 Gr 2 0.25-0.33 1.2-1.6 0.6 0.05 0.05 0.3 0.25 0.4 Cu = 0.3 620 370 13 25 179-229 -
KM 324 IS 2708 Gr 3 0.25-0.33 1.2-1.6 0.6 0.05 0.05 0.3 0.25 0.4 Cu = 0.3 690 495 13 22 201-255 -
IS 2856 Welding Quality Carbon Steel Castings for High Temperature & Pressure Service
KM 325 IS 2856 Gr 1 0.25 1.2 0.6 0.045 0.04 0.5 0.25 0.5 0.03/0.3 485-655 275 20 20 - -
KM 326 IS 2856 Gr 2 0.3 1.0 0.6 0.045 0.04 0.5 0.25 0.5 0.03/0.3 485-655 250 20 20 - -
KM 327 IS 2856 Gr 3 0.25 0.7 0.6 0.045 0.04 0.5 0.25 0.5 0.03/0.3 415-585 205 22 22 - -
DIN 1681 Steel Castings for General Purposes

KM 328 GS - 38 * NOT SPECIFIED - - - - 380 200 25 35 - < 100
KM 329 GS - 45 * NOT SPECIFIED - - - - 450 230 22 27 - < 100
KM 330 GS - 52 NOT SPECIFIED - - - - 520 260 18 22 - < 100
KM 331 GS - 60 NOT SPECIFIED - - - - 600 300 15 20 - < 100
* -Carbon not to exceed 0.25% where welding is intended.
DIN 17182 General Purpose Steel Castings with Enhanced Weldability & Toughness
KM 332 GS - 16 Mn 5 0.2 1.0 -1.5 0.6 0.02 0.025 0.3 0.15 0.4 - 430-600 230 25 45 - 50-100
KM 333 GS - 20 Mn 5 0.23 1.0 -1.5 0.6 0.02 0.025 0.3 0.15 0.4 - 500-650 280 22 40 - 50-100
ASTM-A-27M Carbon Steel Castings for General Applications
KM 334 N-1 0.25 0.75 0.80 0.06 0.05 - - - - - - - - - -
KM 335 N-2 0.35 0.60 0.80 0.06 0.05 - - - - - - - - - -
KM 336 U-60-30 0.25 0.75 0.80 0.06 0.05 - - - - 415 205 22 - - -
KM 337 60-30 0.30 0.60 0.80 0.06 0.05 - - - - 415 205 24 - - -
KM 338 65-35 0.30 0.70 0.80 0.06 0.05 - - - - 450 240 24 - - -
KM 339 70-36 0.35 0.70 0.80 0.06 0.05 - - - - 485 250 22 - - -
KM 340 70-40 0.25 1.20 0.80 0.06 0.05 - - - - 485 275 22 - - -
ASTM-A-128M Austenitic Manganese Steel Castings

KM 341 A 1.05-1.35 11 min 1.0 - 0.07 - - - - - - - - - -
KM 342 B-1 0.9-1.05 11.5-14 1.0 - 0.07 - - - - - - - - - -
KM 343 B-2 1.05-1.2 11.5-14 1.0 - 0.07 - - - - - - - - - -
KM 344 B-3 1.12-1.28 11.5-14 1.0 - 0.07 - - - - - - - - - -
KM 345 B-4 1.2-1.35 11.5-14 1.0 - 0.07 - - - - - - - - - -
KM 346 C 1.05-1.35 11.5-14 1.0 - 0.07 1.5-2.5 - - - - - - - - -
KM 347 D 0.7-1.3 11.5-14 1.0 - 0.07 - - 3.0-4.0 - - - - - - -
KM 348 E-1 0.7-1.3 11.5-14 1.0 - 0.07 - 0.9-1.2 - - - - - - - -
KM 349 E-2 1.05-1.45 11.5-14 1.0 - 0.07 - 1.8-2.1 - - - - - - - -
KM 350 F 1.05-1.35 6.0-8.0 1.0 - 0.07 - 0.9-1.2 - - - - - - - -
ASTM-A-148M High Strength Steel Castings for Structural Purposes

KM 351 80 - 40 - - - 0.06 0.05 - - - - 550 275 18 - - -
KM 352 80 - 50 - - - 0.06 0.05 - - - - 550 345 22 - - -
KM 353 90 - 60 - - - 0.06 0.05 - - - - 620 415 20 - - -
KM 354 105 - 85 - - - 0.06 0.05 - - - - 725 585 17 - - -
KM 355 115 - 95 - - - 0.06 0.05 - - - - 795 655 14 - - -
KM 356 130 - 115 - - - 0.06 0.05 - - - - 895 795 11 - - -
KM 357 135 - 125 - - - 0.06 0.05 - - - - 930 860 9 - - -
KM 358 150 - 135 - - - 0.06 0.05 - - - - 1035 930 7 - - -
KM 359 160 - 145 - - - 0.06 0.05 - - - - 1105 1000 6 - - -
KM 360 165 - 150 - - - 0.02 0.02 - - - - 1140 1035 5 - - -
KM 361 210 - 180 - - - 0.02 0.02 - - - - 1450 1240 4 - - -
KM 362 260 - 210 - - - 0.02 0.02 - - - - 1795 1450 3 - - -
ASTM-A-216M Carbon Steel Castings for High Temperature Service, Suitable for Fusion Welding
KM 363 WCA 0.25 0.70 0.60 0.045 0.04 0.5 0.2 0.5 Cu<0.3, V<0.03 415-585 205 24 - - -
KM 364 WCB 0.30 1.0 0.60 0.045 0.04 0.5 0.2 0.5 Cu<0.3, V<0.03 485-655 250 22 - - -
KM 365 WCC 0.25 1.20 0.60 0.045 0.04 0.5 0.2 0.5 Cu<0.3, V<0.03 485-655 275 22 - - -
IS 4522 Heat Resistant Alloy Steel & Nickel base Castings

KM 401 Grade 1 0.4 1.0 2.0 0.05 0.05 12.0-14.0 0.5 1.0 - 590 - 8 - - -
KM 402 Grade 2 0.3-0.6 1.0 2.0 0.05 0.05 27.0-30.0 0.5 - - 390 - - - - -
KM 403 Grade 3 1.2-1.4 1.0 2.0 0.05 0.05 27.0-30.0 0.5 - - - - - - - -
KM 404 Grade 4 0.2-0.5 1.0 2.0 0.05 0.05 26.0-30.0 0.5 4.0-7.0 - 510 240 7 - - -
KM 405 Grade 5 0.2-0.5 2.0 2.0 0.05 0.05 18.0-20.0 0.5 8.0-10.0 - 490 240 20 - 130-200 -
KM 406 Grade 6 0.2-0.5 2.0 2.0 0.05 0.05 26.0-30.0 0.5 8.0-10.0 - 610 290 10 - 160-220 -
KM 407 Grade 7 0.2-0.5 2.0 2.0 0.05 0.05 23.0-27.0 0.5 11.0-14.0 - 510 250 15 - 150-230 -
KM 408 Grade 8 0.15-0.35 1.5 2.5 0.05 0.05 19.0-21.0 0.5 13.0-15.0 - 450 - 7 - 150-220 -
KM 409 Grade 9 0.2-0.5 2.0 2.0 0.05 0.05 23.0-27.0 0.5 18.0-22.0 - 450 250 10 - 150-210 -
KM 410 Grade 10 0.2-0.6 2.0 2.5 0.05 0.05 28.0-32.0 0.5 18.0-22.0 - 460 240 10 - 140-200 -
KM 411 Grade 11 0.2-0.5 2.0 2.0 0.05 0.05 19.0-23.0 0.5 23.0-27.0 - 440 240 7 - 130-200 -
KM 412 Grade 12 0.35-0.75 2.0 2.5 0.05 0.05 13.0-17.0 0.5 33.0-37.0 - 450 240 5 - 135-200 -
KM 413 Grade 13 0.35-0.75 2.0 2.5 0.05 0.05 17.0-21.0 0.5 37.0-41.0 - 450 240 4 - 135-200 -
KM 414 Grade 14 0.35-0.75 2.0 2.5 0.05 0.05 15.0-19.0 0.5 64.0-68.0 - 410 220 4 - 130-200 -
DIN 17205 Quenched and Tempered Steel Castings for General Applications
KM 415 GS - 30 Mn 5 0.27-0.34 1.2-1.5 0.6 0.015 0.02 - - - - 600-750 450 10 27 - 50-100
KM 416 GS - 25CrMo4 0.22-0.29 0.5-0.8 0.6 0.015 0.02 0.8-1.2 0.2-0.3 - - 700-850 550 10 32 - 50-100
KM 417 GS - 34CrMo4 0.3-0.37 0.5-0.8 0.6 0.015 0.02 0.8-1.2 0.2-0.3 - - 830-980 650 10 27 - 50-100
KM 418 GS - 42CrMo4 0.38-0.45 0.6-1.0 0.6 0.015 0.02 0.8-1.2 0.2-0.3 - - 850-1000 700 10 27 - 50-100
KM 419 GS-30CrMoV6 4 0.27-0.34 0.6-1.0 0.6 0.015 0.02 1.3-1.7 0.3-0.5 - V=0.05-0.15 900-1100 750 12 32 - < 100
KM 420 GS-35CrMoV10 4 0.32-0.39 0.6-1.0 0.6 0.015 0.02 2.2-2.7 0.3-0.5 - V=0.05-0.15 1050-1250 850 10 27 - < 100
KM 421 GS-25CrNiMo4 0.22-0.29 0.6-1.0 0.6 0.015 0.02 0.8-1.2 0.2-0.3 0.8-1.2 - 800-950 650 10 27 - < 100
KM 422 GS-34CrNiMo6 0.3-0.37 0.6-1.0 0.6 0.015 0.02 1.4-1.7 0.2-0.3 1.4-1.7 - 900-1100 800 10 35 - < 100
KM 423 GS-30NiCrMo8 5 0.27-0.34 0.6-1.0 0.6 0.01 0.015 1.1-1.4 0.3-0.4 1.8-2.1 - 1050-1250 950 10 35 - < 100
KM 424 GS-33NiCrMo7 4 4 0.3-0.36 0.5-0.8 0.6 0.007 0.015 0.9-1.2 0.35-0.5 1.5-1.8 - 1050-1250 950 10 35 - < 100
EN 10213 Steel Castings for Pressure Purposes for use at Room Temperature and Elevated Temperature
KM 425 GP240GR 0.18-0.25 1.20 0.6 0.02 0.03 - - - - 420-600 240 22 27 - 100
KM 426 GP240GH 0.18-0.23 0.5-1.2 0.6 0.02 0.03 - - - - 420-600 240 22 27 - 100
KM 427 GP280GH 0.18-0.25 0.8-1.2 0.6 0.02 0.03 - - - - 480-640 280 22 27 - 100
KM 428 G20Mo5 0.15-0.23 0.5-1.0 0.6 0.02 0.025 - 0.4-0.6 - - 440-590 245 22 27 - 100
KM 429 G17CrMo5-5 0.15-0.2 0.5-1.0 0.6 0.02 0.02 1.0-1.5 0.45-0.65 - - 490-690 315 20 27 - 100
KM 430 G17CrMo9-10 0.13-0.2 0.5-0.9 0.6 0.02 0.02 2.0-2.5 0.9-1.2 - - 590-740 400 18 40 - 150
V=0.22-0.3,
KM 431 G12MoCrV5-2 0.1-0.15 0.4-0.7 0.45 0.02 0.03 0.3-0.5 0.4-0.6 - Sn<0.025 510-660 295 17 27 - 100
V=0.2-0.3,
KM 432 G17CrMoV5-10 0.15-0.2 0.5-0.9 0.6 0.015 0.02 1.2-1.5 0.9-1.1 - Sn<0.025 590-780 440 15 27 - 150
KM 433 GX15CrMo5 0.12-0.19 0.5-0.8 0.8 0.025 0.025 4.0-6.0 0.45-0.65 - - 630-760 420 16 27 - 150
KM 434 GX8CrNi12 0.1 0.5-0.8 0.4 0.02 0.03 11.5-12.5 0.5 0.8-1.5 - 540-690 355 18 45 - 300
KM 435 GX4CrNi13-4 0.06 1.0 1.0 0.025 0.035 12.0-13.5 0.7 3.5-5.0 - 760-960 550 15 50 - 300
KM 436 GX23CrMoV12-1 0.2-0.26 0.5-0.8 0.4 0.02 0.03 11.3-12.2 1.0-1.2 1.0 V=0.25-0.35, W<0.5 740-880 540 15 21 - 150
KM 437 GX4CrNiMo16-5-1 0.06 1.0 0.8 0.025 0.035 15.0-17.0 0.7-1.5 4.0-6.0 - 760-960 550 15 60 - 300
DIN 17465 Heat Resistant Steel Castings

KM 438 GX30CrSi6 0.2-0.35 0.5-1.0 1.0-2.5 0.03 0.035 6.0-8.0 - - - - - - - 300 -
KM 439 GX40CrSi13 0.3-0.45 0.5-1.0 1.0-2.5 0.03 0.035 12.0-14.0 - - - - - - - 300 -
KM 440 GX40CrSi17 0.3-0.45 0.5-1.0 1.0-2.5 0.03 0.035 16.0-18.0 - - - - - - - 300 -
KM 441 GX40CrSi23 0.3-0.45 0.5-1.0 1.0-2.5 0.03 0.035 22.0-24.0 - - - - - - - - -
KM 442 GX40CrSi29 0.3-0.45 0.5-1.0 1.0-2.5 0.03 0.035 27.0-30.0 - - - - - - - - -
KM 443 GX130CrSi29 1.20-1.40 0.5-1.0 1.0-2.5 0.03 0.035 27.0-30.0 - - - - - - - - -
KM 444 GX40CrNiSi27-4 0.35-0.5 1.50 1.0-2.5 0.03 0.035 25.0-28.0 - 3.5-5.5 - - - - - - -
KM 445 GX25CrNiSi18-9 0.15-0.30 1.50 1.0-2.5 0.03 0.035 17.0-19.0 - 8.0-10.0 - 440 230 15 - - 25
KM 446 GX40CrNiSi22-9 0.3-0.5 1.50 1.0-2.5 0.03 0.035 21.0-23.0 - 9.0-11.0 - 440 230 8 - - 25
KM 447 GX25CrNiSi 20-14 0.15-0.30 1.50 1.0-2.5 0.03 0.035 19.0-21.0 - 13.0-15.0 - 440 230 10 - - 25
KM 448 GX40CrNiSi25-12 0.3-0.5 1.50 1.0-2.5 0.03 0.035 24.0-26.0 - 11.0-14.0 - 440 230 7 - - 25
KM 449 GX40CrNiSi25-20 0.3-0.5 1.50 1.0-2.5 0.03 0.035 24.0-26.0 - 19.0-21.0 - 440 230 6 - - 25
KM 450 GX40NiCrSi38-18 0.3-0.5 1.50 1.0-2.5 0.03 0.035 17.0-19.0 - 36.0-39.0 - 400 230 5 - - 25
KM 451 GX40NiCrSi35-25 0.3-0.5 1.50 1.0-2.5 0.03 0.035 24.0-26.0 - 34.0-36.0 - 440 230 5 - - 25
KM 452 GX30CrNiSiNb24-24 0.25-0.4 1.50 0.5-2.0 0.03 0.035 23.0-25.0 - 23.0-25.0 Nb=1.2-1.8 440 230 5 - - 25
KM 453 GX40NiCrSiNb38-18 0.3-0.5 1.50 1.0-2.5 0.03 0.035 17.0-19.0 - 36.0-39.0 Nb=1.2-1.8 400 220 5 - - 25
KM 454 GX40NiCrSiNb35-25 0.35-0.45 1.50 1.0-2.5 0.03 0.035 24.0-26.0 - 33.0-35.0 Nb=0.8-1.8 400 220 5 - - 25
ASTM-A-351M Austenitic & Duplex Steel Castings for Pressure Containing Parts
KM 455 CF 3 0.03 1.50 2.0 0.04 0.04 17.0-21.0 0.50 8.0-12.0 - 485 205 35 - - -
KM 456 CF 3 A 0.03 1.50 2.0 0.04 0.04 17.0-21.0 0.50 8.0-12.0 - 530 240 35 - - -
KM 457 CF 8 0.08 1.50 2.0 0.04 0.04 18.0-21.0 0.50 8.0-11.0 - 485 205 35 - - -
KM 458 CF 8 A 0.08 1.50 2.0 0.04 0.04 18.0-21.0 0.50 8.0-11.0 - 530 240 35 - - -
KM 459 CF 3 M 0.03 1.50 1.50 0.04 0.04 17.0-21.0 2.0-3.0 9.0-13.0 - 485 205 30 - - -
KM 460 CF 3 MA 0.03 1.50 1.50 0.04 0.04 17.0-21.0 2.0-3.0 9.0-13.0 - 550 255 30 - - -
KM 461 CF 8 M 0.08 1.50 1.50 0.04 0.04 18.0-21.0 2.0-3.0 9.0-12.0 - 485 205 30 - - -
KM 462 CF 3 MN 0.03 1.50 1.50 0.04 0.04 17.0-21.0 2.0-3.0 9.0-13.0 N=0.1-0.2 515 255 35 - - -
KM 463 CF 8 C 0.08 1.50 2.0 0.04 0.04 18.0-21.0 0.50 9.0-12.0 1.0>Cb>8C 485 205 30 - - -
KM 464 CF 10 0.04-0.10 1.50 2.0 0.04 0.04 18.0-21.0 0.50 8.0-11.0 - 485 205 35 - - -
KM 465 CF 10 M 0.04-0.10 1.50 1.50 0.04 0.04 18.0-21.0 2.0-3.0 9.0-12.0 - 485 205 30 - - -
KM 466 CH 8 0.08 1.50 1.50 0.04 0.04 22.0-26.0 0.50 12.0-15.0 - 450 195 30 - - -
KM 467 CH 10 0.04-0.10 1.50 2.0 0.04 0.04 22.0-26.0 0.50 12.0-15.0 - 485 205 30 - - -
KM 468 CH 20 0.04-0.20 1.50 2.0 0.04 0.04 22.0-26.0 0.50 12.0-15.0 - 485 205 30 - - -
KM 469 CK 20 0.04-0.20 1.50 1.75 0.04 0.04 23.0-27.0 0.50 19.0-22.0 - 450 195 30 - - -
KM 470 HK 30 0.25-0.35 1.50 1.75 0.04 0.04 23.0-27.0 0.50 19.0-22.0 - 450 240 10 - - -
KM 471 HK 40 0.35-0.45 1.50 1.75 0.04 0.04 23.0-27.0 0.50 19.0-22.0 - 425 240 10 - - -
KM 472 HT 30 0.25-0.35 2.0 2.5 0.04 0.04 13.0-17.0 0.50 33.0-37.0 - 450 195 15 - - -
ASTM-A-297M Heat resistant Iron-Chromium-Nickel Steel Castings for General Application

KM 473 HF- 19Cr,9Ni 0.2-0.4 2.0 2.0 0.04 0.04 18.0-23.0 0.5 8.0-12.0 - 485 240 25 - - -
KM 474 HH- 25Cr,12Ni 0.2-0.5 2.0 2.0 0.04 0.04 24.0-28.0 0.5 11.0-14.0 - 515 240 10 - - -
KM 475 HI- 28Cr,15Ni 0.2-0.5 2.0 2.0 0.04 0.04 26.0-30.0 0.5 14.0-18.0 - 485 240 10 - - -
KM 476 HK- 25 Cr,20Ni 0.2-0.6 2.0 2.0 0.04 0.04 24.0-28.0 0.5 18.0-22.0 - 450 240 10 - - -
KM 477 HE- 29Cr,9Ni 0.2-0.5 2.0 2.0 0.04 0.04 26.0-30.0 0.5 8.0-11.0 - 585 275 9 - - -
KM 478 HT- 15Cr,35Ni 0.35-0.75 2.0 2.5 0.04 0.04 15.0-19.0 0.5 33.0-37.0 - 450 - 4 - - -
KM 479 HU- 19Cr,39Ni 0.35-0.75 2.0 2.5 0.04 0.04 17.0-21.0 0.5 37.0-41.0 - 450 - 4 - - -
KM 480 HW- 12Cr,60Ni 0.35-0.75 2.0 2.5 0.04 0.04 10.0-14.0 0.5 58.0-62.0 - 415 - - - - -
KM 481 HX- 17Cr,66Ni 0.35-0.75 2.0 2.5 0.04 0.04 15.0-19.0 0.5 64.0-68.0 - 415 - - - - -
KM 482 HC- 28Cr 0.5 1.0 2.0 0.04 0.04 26.0-30.0 0.5 4.0 - 380 - - - - -
KM 483 HD- 28Cr.5Ni 0.5 1.5 2.0 0.04 0.04 26.0-30.0 0.5 4.0-7.0 - 515 240 8 - - -
KM 484 HL- 29Cr,20Ni 0.2-0.6 2.0 2.0 0.04 0.04 28.0-32.0 0.5 18.0-22.0 - 450 240 10 - - -
KM 485 HN- 20Cr,25Ni 0.2-0.5 2.0 2.0 0.04 0.04 19.0-23.0 0.5 23.0-27.0 - 435 - 8 - - -
KM 486 HP- 26Cr,35Ni 0.35-0.75 2.0 2.5 0.04 0.04 24.0-28.0 0.5 33.0-37.0 - 430 235 4.5 - - -
SEW 390 Hadfields Manganese steel

KM 487 GX-120 Mn 12 1.1-1.3 11.5-13.5 0.5 0.03 0.1 0.5 - - - 585 290 25 - 190-230 -
DIN 17350 Tool Steel

KM 488 X-165 CrMoV 12 1.55-1.75 0.2-0.4 0.25-0.4 0.03 0.03 11.0-12.0 0.5-0.7 V=0.1-0.5, W=0.4-0.6 - - - - 255 max -
SEW 835 Steel Castings for Flame & Induction Hardening

KM 489 G36Mn5 0.32-0.40 1.2-1.5 0.25-0.5 0.035 0.035 - - - - 540 310 17 - - 250
5.5 CAST IRONS
IS 210 GREY CAST IRONS
KM 501 FG 150 NOT SPECIFIED - - - - 150 - - - 130-180 -
EN 1561 GREY CAST IRONS
KM 508 EN-GJL-100 NOT SPECIFIED - - - - 100-200 - - - - 40
KM 509 EN-GJL-150 NOT SPECIFIED - - - - 150-250 98-165 0.8-0.3 - - 30
ASTM-A-48M GREY CAST IRONS
KM 514 150 - - - - - - - - - 150 - - - - -
KM 515 175 - - - - - - - - - 175 - - - - -
KM 516 200 - - - - - - - - - 200 - - - - -
KM 517 225 - - - - - - - - - 225 - - - - -
KM 518 250 - - - - - - - - - 250 - - - - -
KM 519 275 - - - - - - - - - 275 - - - - -
KM 520 300 - - - - - - - - - 300 - - - - -
KM 521 325 - - - - - - - - - 325 - - - - -
KM 522 350 - - - - - - - - - 350 - - - - -
KM 523 375 - - - - - - - - - 375 - - - - -
KM 524 400 - - - - - - - - - 400 - - - - -
5.5.2 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS
IS 1865 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

KM 525 SG 900/2 NOT SPECIFIED - - - - 900 600 2 - 280-360 -
KM 532 SG 400/18 NOT SPECIFIED - - - - 400 250 18 12 130-180 -
KM 533 SG 350/22 NOT SPECIFIED - - - - 350 220 22 12 150 max -
EN 1563 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

KM 534 EN-GJS-350-22-LT NOT SPECIFIED - - - - 350 220 22 12at-40C - -
KM 535 EN-GJS-400-18-LT NOT SPECIFIED - - - - 400 240 18 12at-20C - -
KM 536 EN-GJS-400-15 NOT SPECIFIED - - - - 400 250 15 - - -
ASTM-A-536M NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

KM 541 60-40-18 - - - - - - - - - 415 275 18 - - -
KM 542 65-45-12 - - - - - - - - - 450 310 12 - - -
KM 543 80-55-06 - - - - - - - - - 550 380 6 - - -
KM 544 100-70-03 - - - - - - - - - 690 485 3 - - -
KM 545 120-90-02 - - - - - - - - - 825 620 2 - - -
KM 546 60-42-10 - - - - - - - - - 415 290 10 - - -
KM 547 70-50-05 - - - - - - - - - 485 345 5 - - -
KM 548 80-60-03 - - - - - - - - - 555 415 3 - - -
5.5.3 MALLEABLE CAST IRONS

IS 2107 MALLEABLE CAST IRONS
KM 549 WM 410 NOT SPECIFIED - - - - 410 250 4 - 229 max -
KM 550 WM 340 NOT SPECIFIED - - - - 340 - 3 - 229 max -
EN 1562 MALLEABLE CAST IRONS

KM 551 EN-GJMB-350-10 NOT SPECIFIED - - - - 350 200 10 - 150 max -
KM 552 EN-GJMB-450-6 NOT SPECIFIED - - - - 450 270 6 - 150-200 -
KM 556 EN-GJMW-350-4 NOT SPECIFIED - - - - 350 - 4 - 230 max -
KM 557 EN-GJMW-400-5 NOT SPECIFIED - - - - 400 220 5 - 220 max -

KM 560 22010 - - - - - - - - - 340 220 10 - 156 max -

KM 561 280M10 - - - - - - - - - 400 280 10 - 149-197 -
KM 562 310M8 - - - - - - - - - 450 310 8 - 156-197 -
KM 563 310M6 - - - - - - - - - 450 310 6 - 156-207 -
KM 564 340M5 - - - - - - - - - 480 340 5 - 179-229 -
KM 565 410M4 - - - - - - - - - 550 410 4 - 197-241 -
KM 566 480M3 - - - - - - - - - 590 480 3 - 217-269 -
KM 567 550M2 - - - - - - - - - 650 550 2 - 241-285 -
KM 568 620M1 - - - - - - - - - 720 620 1 - 269-321 -
KM 601 201 0.15 5.5-7.5 1.0 0.03 0.06 16.0-18.0 - 3.5-5.5 N < 0.25 515 260 40 - - -
KM 602 202 0.15 7.5-10.0 1.0 0.03 0.06 17.0-19.0 - 4.0-6.0 N < 0.25 620 260 40 - 241 -
KM 603 301 0.15 2.0 1.0 0.03 0.045 16.0-18.0 - 6.0-8.0 N < 0.1 515 205 40 - 217 -
KM 604 302 0.15 2.0 0.75 0.03 0.045 17.0-19.0 - 8.0-10.0 N < 0.1 515 205 40 - 201 -
KM 605 304 0.08 2.0 0.75 0.03 0.045 18.0-20.0 - 8.0-10.5 N < 0.1 515 205 40 - 201 -
KM 606 304 L 0.03 2.0 0.75 0.03 0.045 18.0-20.0 - 8.0-12.0 N < 0.1 485 170 40 - 201 -
KM 607 304 H 0.04-0.10 2.0 0.75 0.03 0.045 18.0-20.0 - 8.0-10.5 - 515 205 40 - 201 -
KM 608 304 N 0.08 2.0 0.75 0.03 0.045 18.0-20.0 - 8.0-10.5 N = 0.1-0.16 550 230 30 - 201 -
KM 609 304 L N 0.03 2.0 0.75 0.03 0.045 18.0-20.0 - 8.0-12.0 N = 0.1-0.16 515 205 40 - 201 -
KM 610 305 0.12 2.0 0.75 0.03 0.045 17.0-19.0 - 10.5-13.0 - 515 205 40 - 183 -
KM 611 309 S 0.08 2.0 0.75 0.03 0.045 22.0-24.0 - 12.0-15.0 - 515 205 40 - 217 -
KM 612 309 H 0.04-0.10 2.0 0.75 0.03 0.045 22.0-24.0 - 12.0-15.0 - 515 205 40 - 217 -
KM 613 309 Cb 0.08 2.0 0.75 0.03 0.045 22.0-24.0 - 12.0-16.0 1.1 >Cb>10xC 515 205 40 - 217 -
KM 614 309 H Cb 0.04-0.10 2.0 0.75 0.03 0.045 22.0-24.0 - 12.0-16.0 1.1 >Cb>10xC 515 205 40 - 217 -
KM 615 310 S 0.08 2.0 1.5 0.03 0.045 24.0-26.0 - 19.0-22.0 - 515 205 40 - 217 -
KM 616 310 H 0.04-0.10 2.0 0.75 0.03 0.045 24.0-26.0 - 19.0-22.0 - 515 205 40 - 217 -
KM 617 310 Cb 0.08 2.0 1.5 0.03 0.045 24.0-26.0 - 19.0-22.0 1.1 >Cb>10xC 515 205 40 - 217 -
KM 618 310 H Cb 0.04-0.10 2.0 0.75 0.03 0.045 24.0-26.0 - 19.0-22.0 1.1 >Cb>10xC 515 205 40 - 217 -
KM 619 310 Mo L N 0.03 2.0 0.5 0.01 0.03 24.0-26.0 2.0-3.0 21.0-23.0 N = 0.1-0.16 550 240 30 - 217 -
KM 620 316 0.08 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N < 0.1 515 205 40 - 217 -
KM 621 316 L 0.03 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N < 0.1 485 170 40 - 217 -
KM 622 316 H 0.04-0.10 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 - 515 205 40 - 217 -
0.7>Ti>5x(C+N),
KM 623 316 Ti 0.08 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N < 0.1 515 205 40 - 217 -
1.1>Cb>10xC,
KM 624 316 Cb 0.08 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N < 0.1 515 205 30 - 217 -
KM 625 316 N 0.08 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N = 0.1-0.16 550 240 35 - 217 -
KM 626 316 L N 0.03 2.0 0.75 0.03 0.045 16.0-18.0 2.0-3.0 10.0-14.0 N = 0.1-0.16 515 205 40 - 217 -
KM 627 317 0.08 2.0 0.75 0.03 0.045 18.0-20.0 3.0-4.0 11.0-15.0 N < 0.1 515 205 35 - 217 -
KM 628 317 L 0.03 2.0 0.75 0.03 0.045 18.0-20.0 3.0-4.0 11.0-15.0 N < 0.1 515 205 40 - 217 -
KM 629 317 L N 0.03 2.0 0.75 0.03 0.045 18.0-20.0 3.0-4.0 11.0-15.0 N = 0.1-0.22 550 240 40 - 217 -
0.7>Ti>5x(C+N),
KM 630 321 0.08 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-12.0 N<0.1 515 205 40 - 217 -
KM 631 321 H 0.04-0.10 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-12.0 0.7>Ti>4x(C+N) 515 205 40 - 217 -
KM 632 347 0.08 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-13.0 1.0>Cb>10xC 515 205 40 - 201 -
KM 633 347 H 0.04-0.10 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-13.0 1.0>Cb>8xC 515 205 40 - 201 -
1.0>Cb+Ta>10xC,
KM 634 348 0.08 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-13.0 Ta< 0.1, Co=0.2 515 205 40 - 201 -
1.0>Cb+Ta>8xC,
KM 635 348 H 0.04-0.10 2.0 0.75 0.03 0.045 17.0-19.0 - 9.0-13.0 Ta< 0.1, Co=0.2 515 205 40 - 201 -
KM 636 X5CrNi18-10 0.07 2.0 1.0 0.015 0.045 17.0-19.5 - 8.0-10.5 N < 0.11 520-720 210 45 90 - < 75
KM 637 X4CrNi18-12 0.06 2.0 1.0 0.015 0.045 17.0-19.0 - 11.0-13.0 N < 0.11 500-650 220 45 - - <6
KM 638 X8CrNiS18-9 0.10 2.0 1.0 0.15-0.35 0.045 17.0-19.0 - 8.0-10.0 N < 0.11, Cu < 1.0 500-700 230 35 - - < 75
KM 639 X2CrNi19-11 0.03 2.0 1.0 0.015 0.045 18.0-20.0 - 10.0-12.0 N < 0.11 500-650 200 45 90 - < 75
KM 640 X2CrNiN18-10 0.03 2.0 1.0 0.015 0.045 17.0-19.5 - 8.5-11.5 N=0.12-0.22 550-750 270 40 90 - < 75
KM 641 X6CrNiTi18-10 0.08 2.0 1.0 0.015 0.045 17.0-19.0 - 9.0-12.0 0.7>Ti>5xC 500-700 200 40 90 - < 75
KM 642 X6CrNiNb18-10 0.08 2.0 1.0 0.015 0.045 17.0-19.0 - 9.0-12.0 1.0 >Nb>10xC 500-700 200 40 90 - < 75
KM 643 X5CrNiMo17-12-2 0.07 2.0 1.0 0.015 0.045 16.5-18.5 2.0-2.5 10.0-13.0 N < 0.11 520-670 220 45 90 - < 75
KM 644 X2CrNiMo17-12-2 0.03 2.0 1.0 0.015 0.045 16.5-18.5 2.0-2.5 10.0-13.0 N < 0.11 520-670 220 45 90 - < 75
KM 645 X2CrNiMoN17-11-2 0.03 2.0 1.0 0.015 0.045 16.5-18.5 2.0-2.5 10.0-12.0 N=0.12-0.22 580-780 280 40 90 - < 75
KM 646 X6CrNiMoTi17-12-2 0.08 2.0 1.0 0.015 0.045 16.5-18.5 2.0-2.5 10.5-13.5 0.7>Ti>5xC 520-670 220 40 90 - < 75
KM 647 X6CrNiMoNb17-12-2 0.08 2.0 1.0 0.015 0.045 16.5-18.5 2.0-2.5 10.5-13.5 1.0 >Nb>10xC 520-670 220 40 90 - < 75
KM 648 X2CrNiMoN17-13-3 0.03 2.0 1.0 0.015 0.045 16.5-18.5 2.5-3.0 11.0-14.0 N=0.12-0.22 580-780 280 40 90 - < 75
KM 649 X2CrNiMo18-14-3 0.03 2.0 1.0 0.015 0.045 17.0-19.0 2.5-3.0 12.5-15.0 N < 0.11 520-670 220 45 90 - < 75
KM 650 X3CrNiMo17-13-3 0.05 2.0 1.0 0.015 0.045 16.5-18.5 2.5-3.0 10.5-13.0 N < 0.11 530-730 220 40 90 - < 75
KM 651 X2CrNiMo18-15-4 0.03 2.0 1.0 0.015 0.045 17.5-19.5 3.0-4.0 13.0-16.0 N < 0.11 530-730 220 40 90 - < 75
KM 652 X2CrNiMoN17-13-5 0.03 2.0 1.0 0.015 0.045 16.5-18.5 4.0-5.0 12.5-14.5 N=0.12-0.22 580-780 270 40 90 - < 75
5.6.2 FERRITIC AND MARTENSITIC STAINLESS STEELS
KM 653 405 0.08 1.0 1.0 0.03 0.04 11.5-14.5 - 0.6 Al=0.1-0.3 415 170 20 - 179 -
KM 654 409 0.08 1.0 1.0 0.03 0.045 10.5-11.75 - 0.5 0.75>Ti>6xC 380 205 20 - 179 -
KM 655 429 0.12 1.0 1.0 0.03 0.04 14.0-16.0 - - - 450 205 22 - 183 -
KM 656 430 0.12 1.0 1.0 0.03 0.04 16.0-18.0 - 0.75 - 450 205 22 - 183 -
N<0.04,Al<0.15,
Ti>0.2+4xC+N,
KM 657 439 0.07 1.0 1.0 0.03 0.04 17.0-19.0 - 0.5 Ti < 1.1 415 205 22 - 183 -
N<0.035,Ti<0.8,
KM 658 444 0.025 1.0 1.0 0.03 0.04 17.5-19.5 1.75-2.5 1.0 Ti+Cb>0.2+4x(C+N) 415 275 20 - 217 -
KM 659 410 0.15 1.0 1.0 0.03 0.04 11.5-13.5 - 0.75 - 450 205 20 - 217 -
KM 660 410 S 0.08 1.0 1.0 0.03 0.04 11.5-13.5 - 0.6 - 415 205 22 - 183 -
KM 661 X6Cr13 0.08 1.0 1.0 0.015 0.04 12.0-14.0 - - - 400-600 220 19 - - < 12
KM 662 X6CrAl13 0.08 1.0 1.0 0.015 0.04 12.0-14.0 - - Al=0.1-0.3 400-600 210 17 - - < 12
KM 663 X6Cr17 0.08 1.0 1.0 0.015 0.04 16.0-18.0 - - - 450-600 240 18 - - < 12
KM 664 X3CrTi17 0.05 1.0 1.0 0.015 0.04 16.0-18.0 - - Ti=4(C+N)+0.15-0.8 420-600 230 23 - - < 12
KM 665 X6CrMoS17 0.08 1.5 1.5 0.15-0.35 0.04 16.0-18.0 0.2-0.6 - - 450-650 270 - - 200 < 12
KM 666 X12Cr13 0.08-0.15 1.5 1.0 0.015 0.04 11.5-13.5 - 0.75 - 650-850 450 12 - - < 75
KM 667 X12CrS13 0.08-0.15 1.5 1.0 0.15-0.35 0.04 12.0-14.0 0.6 - - 650-800 450 15 30 - < 25
KM 668 X20Cr13 0.16-0.25 1.5 1.0 0.015 0.04 12.0-14.0 - - - 750-950 550 10 - - < 75
KM 669 X30Cr13 0.26-0.35 1.5 1.0 0.015 0.04 12.0-14.0 - - - 800-1000 600 10 - - < 75
KM 670 X39Cr13 0.36-0.42 1.0 1.0 0.015 0.04 12.5-14.5 - - - 760 max - 12 - 240 < 12
KM 671 X46Cr13 0.43-0.50 1.0 1.0 0.015 0.04 12.5-14.5 - - - 780 max - 12 - 245 < 12
KM 672 X50CrMoV15 0.45-0.55 1.0 1.0 0.015 0.04 14.0-15.0 0.5-0.8 - V=0.1-0.2 850 max - 12 - 280 < 12
KM 673 X14CrMoS17 0.10-0.17 1.5 1.0 0.15-0.35 0.04 15.5-17.5 0.2-0.6 - - 640-840 450 - - - < 25
KM 674 X17CrNi16-2 0.12-0.22 1.5 1.0 0.015 0.04 15.0-17.0 - 1.5-2.5 - 750-950 550 14 20 - < 25
KM 675 X3CrNiMo13-4 0.05 1.5 0.7 0.015 0.04 12.0-14.0 0.3-0.7 3.5-4.5 N>0.02 900-1100 800 11 70 - < 75
KM 676 UNS-S31803 0.03 2.0 1.0 0.02 0.03 21.0-23.0 2.5-3.5 4.5-6.5 N=0.08-0.20 620 450 25 - 293 -
KM 677 UNS-S32205 0.03 2.0 1.0 0.02 0.03 22.0-23.0 3.0-3.5 4.5-6.5 N=0.14-0.20 620 450 25 - 293 -
N=0.05-0.20,
KM 678 UNS-S32304 0.03 2.5 1.0 0.03 0.04 21.5-24.5 0.05-0.60 3.0-5.5 Cu=0.05-0.60 600 400 25 - 290 -
KM 679 329 0.08 1.0 0.75 0.03 0.04 23.0-28.0 1.0-2.0 2.5-5.0 - 620 485 15 - 269 -
KM 680 X3CrNiMoN27-5-2 0.05 2.0 1.0 0.015 0.035 25.0-28.0 1.3-2.0 4.5-6.5 N=0.05-0.2 600-800 450 20 55 - -
KM 681 X2CrNiMoN22-5-3 0.03 2.0 1.0 0.015 0.035 21.0-23.0 2.5-3.5 4.5-6.5 N=0.1-0.22 640-900 450 30 120 - -
N=0.05-0.2,
KM 682 X2CrNiN23-4 0.03 2.5 1.0 0.015 0.035 22.0-24.0 0.1-0.6 3.5-5.5 Cu=0.1-0.6 600-820 400 25 85 - -

EN 10028-2 Unalloyed & Alloy Steel Flat Products with Elevated Temperature Properties for Pressure Purposes
Cu<0.3,Nb<0.01,
Ti<0.03,V<0.02,
KM 701 P235GH 0.16 0.4-1.2 0.35 0.025 0.03 0.3 0.08 0.3 Al>0.02, 360-480 235 25 27 at 00C - < 16
Cu<0.3,Nb<0.01,
Ti<0.03,V<0.02,
KM 702 P265GH 0.20 0.5-1.4 0.40 0.025 0.03 0.3 0.08 0.3 Al>0.02, 410-530 265 23 27 at 00C - < 16
Cu<0.3,Nb<0.01,
Ti<0.03,V<0.02,
KM 703 P295GH 0.08-0.20 0.9-1.5 0.40 0.025 0.03 0.3 0.08 0.3 Al>0.02, 460-580 295 22 27 at 00C - < 16
Cu<0.3,Nb<0.01,
Ti<0.03,V<0.02,
KM 704 P355GH 0.10-0.22 1.0-1.7 0.6 0.025 0.03 0.3 0.08 0.3 Al>0.02, 510-650 355 21 27 at 00C - < 16
KM 705 16Mo3 0.12-0.20 0.4-0.9 0.35 0.025 0.03 0.3 0.25-0.35 0.3 Cu < 0.3 440-590 260 23 31at200C - < 60
KM 706 13CrMo4-5 0.08-0.14 0.4-1.0 0.35 0.025 0.03 0.7-1.15 0.4-0.6 - - 440-590 295 20 31at200C - < 60
KM 707 10CrMo9-10 0.08-0.14 0.4-0.8 0.5 0.025 0.03 2.0-2.5 0.9-1.1 - - 480-630 290 18 31at200C - < 60
KM 708 11CrMo9-10 0.08-0.15 0.4-0.8 0.5 0.025 0.03 2.0-2.5 0.9-1.1 - - 520-670 310 18 31at200C - < 60
ASTM-A-515M Carbon Steel Pressure Vessel Plates for Intermediate & High Temperature Service
KM 709 Grade 60 0.24 0.9 0.15-0.4 0.035 0.035 - - - - 415-550 220 25 - - -
KM 710 Grade 65 0.28 0.9 0.15-0.4 0.035 0.035 - - - - 450-585 240 23 - - -
KM 711 Grade 70 0.31 1.20 0.15-0.4 0.035 0.035 - - - - 485-620 260 21 - - -
ASTM-A-516M Carbon Steel Pressure Vessel Plates for Moderate & Lower Temperature Service
KM 712 Grade 55 0.18 0.6-0.9 0.15-0.4 0.035 0.035 - - - - 380-515 205 27 - - -
KM 713 Grade 60 0.21 0.6-0.9 0.15-0.4 0.035 0.035 - - - - 415-550 220 25 - - -
KM 714 Grade 65 0.24 0.85-1.2 0.15-0.4 0.035 0.035 - - - - 450-585 240 23 - - -
KM 715 Grade 70 0.27 0.85-1.2 0.15-0.4 0.035 0.035 - - - - 485-620 260 21 - - -
IS 2002 Steel Pressure Vessel Plates for Intermediate & High Temperature Service including Boilers
KM 716 Grade 1 0.18 0.5-1.2 0.15-0.35 0.04 0.035 - - - - 360-480 215 24 - - 60
KM 717 Grade 2 0.20 0.5-1.2 0.15-0.35 0.04 0.035 - - - - 410-530 245 22 - - 60
KM 718 Grade 3 0.22 0.5-1.2 0.15-0.35 0.04 0.035 - - - - 460-580 280 21 - - 60
BS 1501-1 Carbon-Manganese Steel Plates for Fired and Unfired Pressure Vessels
KM 719 141 - Gr 360 0.16 0.5 - 0.05 0.05 0.25 0.1 0.3 Cu = 0.3 max 360-480 205 25 - - 16
KM 720 154 - Gr 360 0.2 0.3-1.2 - 0.05 0.05 0.25 0.1 0.3 Cu = 0.3 max 360-480 205 23 - - 10
KM 721 154 - Gr 400 0.24 0.4-1.2 - 0.05 0.05 0.25 0.1 0.3 Cu = 0.3 max 400-520 235 23 - - 10
KM 722 154 - Gr 430 0.25 0.4-1.2 - 0.05 0.05 0.25 0.1 0.3 Cu = 0.3 max 430-550 250 22 - - 10
KM 723 151 - Gr 360 0.17 0.4-1.2 0.35 0.045 0.03 0.25 0.1 0.3 Cu = 0.3 max 360-480 205 26 - - 16
KM 724 151 - Gr 400 0.20 0.5-1.3 0.35 0.045 0.03 0.25 0.1 0.3 Cu = 0.3 max 400-520 225 24 - - 16
KM 725 151 - Gr 430 0.25 0.6-1.4 0.35 0.045 0.03 0.25 0.1 0.3 Cu = 0.3 max 430-550 250 23 - - 16
KM 726 161 - Gr 360 0.17 0.4-1.2 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu = 0.3 max 360-480 205 26 - - 16
KM 727 161 - Gr 400 0.20 0.5-1.3 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu = 0.3 max 400-520 225 24 - - 16
KM 728 161 - Gr 430 0.25 0.6-1.4 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu = 0.3 max 430-550 250 23 - - 16
KM 729 164 - Gr 360 0.20 0.4-1.2 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu<0.3, Al>0.015 360-480 255 25 27at-20C - 16
KM 730 164 - Gr 400 0.23 0.5-1.3 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu<0.3, Al>0.015 400-520 275 23 27at-20C - 16
Cu < 0.3, 27 at
KM 731 223 - Gr 460 0.20 0.8-1.6 0.1-0.4 0.03 0.03 0.25 0.1 0.3 Nb=0.01-0.06 460-580 340 22 -300 C - 16
Cu < 0.3, 27 at
KM 732 223 - Gr 490 0.20 0.9-1.6 0.1-0.5 0.03 0.03 0.25 0.1 0.3 Nb=0.01-0.06 490-610 355 21 -300 C - 16
KM 733 224 - Gr 400 0.18 0.9-1.5 0.1-0.35 0.03 0.03 0.25 0.1 0.75 Cu<0.3, Al>0.015 400-520 275 23 27at-50C - 16
KM 734 224 - Gr 430 0.20 0.9-1.5 0.1-0.4 0.03 0.03 0.25 0.1 0.75 Cu<0.3, Al>0.015 430-550 305 22 27at-50C - 16
KM 735 224 - Gr 460 0.22 0.9-1.6 0.1-0.4 0.03 0.03 0.25 0.1 0.75 Cu<0.3, Al>0.015 460-580 325 21 27at-50C - 16
KM 736 224 - Gr 490 0.22 0.9-1.6 0.1-0.4 0.03 0.03 0.25 0.1 0.75 Cu<0.3, Al>0.015 490-610 325 21 27at-50C - 16
Cu<0.3,Al>0.015 27 at
KM 737 225 - Gr 460 0.20 0.8-1.6 0.1-0.4 0.03 0.03 0.25 0.1 0.75 Nb=0.01-0.06 460-580 340 22 -600 C 16
Cu<0.3,Al>0.015 27 at
KM 738 225 - Gr 490 0.20 0.9-1.6 0.1-0.5 0.03 0.03 0.25 0.1 0.75 Nb=0.01-0.06 490-610 355 21 -500 C - 16
BS 3059-1 Boiler & Superheater Low Tensile Carbon Steel Tubes w.o. Specified Elevated Temperature Props
KM 739 HFS 320 0.16 0.3-0.7 0.1-0.35 0.04 0.04 - - - - 320-480 195 25 - - -
KM 740 CFS 320 0.16 0.3-0.7 0.1-0.35 0.04 0.04 - - - - 320-480 195 25 - - -
KM 741 ERW 320 0.16 0.3-0.7 0.35 0.04 0.04 - - - - 320-480 195 25 - - -
KM 742 CEW 320 0.16 0.3-0.7 0.35 0.04 0.04 - - - - 320-480 195 25 - - -
BS 3059-2 Boiler & Superheater, Carbon, Alloy & Stainless Steel Tubes with Elevated Temperature Properties
KM 743 360 0.17 0.4-0.8 0.1-0.35 0.035 0.035 - - - - 360-500 235 24 - - -
KM 744 440 0.12-0.18 0.9-1.2 0.1-0.35 0.035 0.035 - - - - 440-580 245 21 - - -
KM 745 243 0.12-0.2 0.4-0.8 0.1-0.35 0.035 0.035 - 0.25-0.35 - Al<0.012 480-630 275 22 - - -
KM 746 620-460 0.1-0.15 0.4-0.7 0.1-0.35 0.03 0.03 0.7-1.1 0.45-0.65 - Al<0.02 460-610 180 22 - - -
KM 747 622-490 0.08-0.15 0.4-0.7 0.50 0.03 0.03 2.0-2.5 0.9-1.2 - Al<0.02 490-640 275 20 - - -
KM 748 629-470 0.15 0.3-0.6 0.25-1.0 0.03 0.03 8.0-10.0 0.9-1.1 - Al<0.02 470-620 185 20 - - -
KM 749 629-590 0.15 0.3-0.6 0.25-1.0 0.03 0.03 8.0-10.0 0.9-1.1 - Al<0.02 590-740 400 18 - - -
KM 750 762 0.17-0.23 1.0 0.50 0.03 0.03 10.0-12.5 0.8-1.2 0.3-0.8 V=0.25-0.35 720-870 470 15 - - -
KM 751 304S51 0.04-0.1 2.0 1.0 0.03 0.04 17.0-19.0 - 8.0-11.0 - 490-690 230 35 - -
KM 752 316S51 0.04-0.1 2.0 1.0 0.03 0.04 16.5-18.5 2.0-2.5 10.5-13.5 - 510-710 240 35 - -
KM 753 316S52 0.04-0.1 2.0 1.0 0.03 0.04 16.5-18.5 2.0-2.5 10.5-13.5 B=0.0015-0.006 510-710 240 35 - -
KM 754 321S51 (1010) 0.04-0.1 2.0 1.0 0.03 0.04 17.0-19.0 - 9.0-12.0 0.8 > Ti > 5xC 510-710 235 35 - -
KM 755 321S51 (1105) 0.04-0.1 2.0 1.0 0.03 0.04 17.0-19.0 - 9.0-12.0 0.8 > Ti > 5xC 490-690 190 35 - -
KM 756 347S51 0.04-0.1 2.0 1.0 0.03 0.04 17.0-19.0 - 9.0-13.0 1.2 > Nb > 10xC 510-710 240 35 - -
V=0.15-0.4,
Nb=0.75-1.25,
KM 757 215S15 0.06-0.15 5.5-7.0 0.2-1.0 0.03 0.04 14.0-16.0 0.8-1.2 9.0-11.0 B=0.003-0.009 540-740 270 35 - - -
BS 3602-1 Seamless, Electric Resistance Welded & Induction Welded Pipes & Tubes of Carbon-Manganese Steels
KM 758 360 - Seamless 0.17 0.3-0.8 0.1-0.35 0.035 0.035 - - - Al < 0.06 360-500 235 25 - - 16
KM 759 360 - Welded 0.17 0.3-0.8 0.35 0.035 0.035 - - - Al < 0.06 360-500 235 25 - - 16
KM 760 430 - Seamless 0.21 0.4-1.2 0.1-0.35 0.035 0.035 - - - Al < 0.06 430-570 275 22 - - 16
KM 761 430 - Welded 0.21 0.4-1.2 0.35 0.035 0.035 - - - Al < 0.06 430-570 275 22 - - 16
Al < 0.06,
KM 762 500Nb-Seamless 0.22 1.0-1.5 0.15-0.35 0.03 0.035 - - - Nb=0.015-0.1 500-650 355 21 - - 16
BS 3602-2 Longitudinally Arc Welded Pipes & Tubes of Carbon-Manganese Steels

KM 763 430 0.25 0.6-1.4 0.1-0.35 0.03 0.03 0.25 0.1 0.3 Cu < 0.3 430-550 250 23 - - 16
KM 764 490 0.22 0.9-1.6 0.1-0.4 0.03 0.03 0.25 0.1 0.75 Cu<0.3, Al>0.015 490-610 325 21 - - 16
ASTM-A-213 Seamless Ferritic & Austenitic Alloy Steel Boiler, Superheater & Heat-Exchanger Tubes
KM 765 T2 0.1-0.2 0.3-0.61 0.1-0.3 0.025 0.025 0.5-0.81 0.44-0.65 - - 415 205 30 - - -
KM 766 T5 0.15 0.3-0.6 0.5 0.025 0.025 4.0-6.0 0.45-0.65 - - 415 205 30 - - -
KM 767 T 5b 0.15 0.3-0.6 1.0-2.0 0.025 0.025 4.0-6.0 0.45-0.65 - - 415 205 30 - - -
KM 768 T 5c 0.12 0.3-0.6 0.5 0.025 0.025 4.0-6.0 0.45-0.65 - 4xC < Ti < 0.7 415 205 30 - - -
KM 769 T9 0.15 0.3-0.6 0.25-1.0 0.025 0.025 8.0-10.0 0.9-1.1 - - 415 205 30 - - -
KM 770 T 11 0.05-0.15 0.3-0.6 0.5-1.0 0.025 0.025 1.0-1.5 0.44-0.65 - - 415 205 30 - - -
KM 771 T 12 0.05-0.15 0.3-0.61 0.50 0.025 0.025 0.8-1.25 0.44-0.65 - - 415 220 30 - - -
KM 772 T 17 0.15-0.25 0.3-0.61 0.1-0.35 0.025 0.025 0.8-1.25 - - V > 0.15 415 205 30 - - -
KM 773 T 21 0.05-0.15 0.3-0.6 0.50 0.025 0.025 2.65-3.35 0.8-1.06 - - 415 205 30 - - -
KM 774 T 22 0.05-0.15 0.3-0.6 0.50 0.025 0.025 1.9-2.6 0.87-1.13 - - 415 205 30 - - -
V=0.18-0.25,
Cb=0.06-0.1,
N=0.03-0.07,
KM 775 T 91 0.08-0.12 0.3-0.6 0.2-0.5 0.01 0.02 8.0-9.5 0.85-1.05 0.4 Al < 0.04 585 415 20 - - -
V=0.15-0.25,
W=1.5-2,Al<0.04
Cb=0.04-0.09,
B=0.001-0.006,
KM 776 T 92 0.07-0.13 0.3-0.6 0.50 0.01 0.02 8.5-9.5 0.3-0.6 0.4 N=0.03-0.07 620 440 20 - - -
N < 0.035,
0.8>Ti+Cb>0.2
KM 777 18 Cr-2 Mo 0.025 1.0 1.0 0.03 0.04 17.5-19.5 1.75-2.5 Ni+Cu<1.0 +4x(C+N) 415 275 20 - - -
KM 778 TP 304 0.08 2.0 0.75 0.03 0.04 18.0-20.0 - 8.0-11.0 - 515 205 35 - - -
KM 779 TP 304 H 0.04-0.1 2.0 0.75 0.03 0.04 18.0-20.0 - 8.0-11.0 - 515 205 35 - - -
KM 780 TP 304 N 0.08 2.0 0.75 0.03 0.04 18.0-20.0 - 8.0-11.0 N=0.1-0.16 550 240 35 - - -
KM 781 TP 304 LN 0.035 2.0 0.75 0.03 0.04 18.0-20.0 - 8.0-11.0 N=0.1-0.16 485 170 35 - - -
KM 782 TP 304 L 0.035 2.0 0.75 0.03 0.04 18.0-20.0 - 8.0-13.0 - 515 205 35 - - -
KM 783 TP 309 Cb 0.08 2.0 0.75 0.03 0.045 22.0-24.0 0.75 12.0-16.0 10xC<Cb+Ta<1.1 515 205 35 - - -
KM 784 TP 309 HCb 0.04-0.1 2.0 0.75 0.03 0.045 22.0-24.0 0.75 12.0-16.0 10xC<Cb+Ta<1.1 515 205 35 - - -
KM 785 TP 309 S 0.08 2.0 0.75 0.03 0.045 22.0-24.0 0.75 12.0-15.0 - 515 205 35 - - -
Cb+Ta=0.2-0.6,
KM 786 TP 310 HCbN 0.04-0.1 2.0 0.75 0.03 0.03 24.0-26.0 - 17.0-23.0 N=0.15-0.35 655 295 30 - - -
KM 787 TP 316 0.08 2.0 0.75 0.03 0.04 16.0-18.0 2.0-3.0 11.0-14.0 - 515 205 35 - - -
KM 788 TP 317 0.08 2.0 0.75 0.03 0.04 18.0-20.0 3.0-4.0 11.0-14.0 - 515 205 35 - - -
KM 789 TP 321 0.08 2.0 0.75 0.03 0.04 17.0-20.0 - 9.0-13.0 5xC < Ti < 0.6 515 205 35 - - -
KM 790 TP 347 0.08 2.0 0.75 0.03 0.04 17.0-20.0 - 9.0-13.0 10xC<Cb+Ta<1.0 515 205 35 - - -
KM 791 TP 347 HFG 0.06-0.1 2.0 0.75 0.03 0.04 17.0-20.0 - 9.0-13.0 8xC<Cb+Ta<1.0 550 205 35 - - -
KM 792 TP 348 0.08 2.0 0.75 0.03 0.04 17.0-20.0 - 9.0-13.0 10xC<Cb+Ta<1.0 515 205 35 - - -
ASTM-A-106 Seamless Carbon Steel Pipes for High Temperature Service

KM 793 Grade A 0.25 0.27-0.93 0.1 min 0.035 0.035 0.40 0.15 0.40 Cu<0.4,V<0.08 330 205 28 - - -
KM 794 Grade B 0.30 0.29-1.06 0.1 min 0.035 0.035 0.40 0.15 0.40 Cu<0.4,V<0.08 415 240 22 - - -
KM 795 Grade C 0.35 0.29-1.06 0.1 min 0.035 0.035 0.40 0.15 0.40 Cu<0.4,V<0.08 485 275 20 - - -

KM 796 St 35.8 0.17 0.4-0.8 0.1-0.35 0.04 0.04 - - - - 360-480 235 25 34 - 16
KM 797 St 45.8 0.21 0.4-1.2 0.1-0.35 0.04 0.04 - - - - 410-530 255 21 27 - 16
KM 798 17 Mn 4 0.14-0.20 0.9-1.2 0.2-0.4 0.04 0.04 0.30 - - - 460-580 270 23 34 - 16
KM 799 19 Mn 5 0.17-0.22 1.0-1.3 0.3-0.6 0.04 0.04 0.30 - - - 510-610 310 19 34 - 16
KM 800 15 Mo 3 0.12-0.20 0.4-0.8 0.1-0.35 0.035 0.035 - 0.25-0.35 - - 450-600 270 22 34 - 16
KM 801 13 CrMo 4 4 0.10-0.18 0.4-0.7 0.1-0.35 0.035 0.035 0.7-1.1 0.45-0.65 - - 440-590 290 22 34 - 16
KM 802 10 CrMo 9 10 0.08-0.15 0.4-0.7 0.50 0.035 0.035 2.0-2.5 0.9-1.2 - - 450-600 280 20 34 - 16
KM 803 14 MoV 6 3 0.10-0.18 0.4-0.7 0.1-0.35 0.035 0.035 0.3-0.6 0.5-0.7 - V= 0.22-0.32 460-610 320 20 41 - 16
KM 804 X 20 CrMoV 12 1 0.17-0.23 1.0 0.50 0.03 0.03 10.0-12.5 0.8-1.2 0.3-0.8 V= 0.25-0.35 690-840 490 17 34 - 16
KM 805 15 NiCuMoNb 5 0.17 0.25-0.5 0.8-1.2 0.025 0.03 0.3 0.25-0.5 1.0-1.3 Cu=0.5-0.8, Nb=0.015-0 590-760 410 16 41 175-225 -
5.8 SPRING STEELS
IS 2507 Cold Rolled Steel Strips for Springs

KM 806 Gr 1 - 45 C 8 0.4-0.5 0.6-0.9 0.1-0.35 0.05 0.05 - - - - 1180-1420 1030 6 - 335-405 -
KM 807 Gr 2 - 55 C 6 0.5-0.6 0.5-0.65 0.1-0.35 0.05 0.05 - - - - 1180-1420 1030 6 - 335-405 -
KM 808 Gr 3 - 65 C 6 0.6-0.7 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1180-1420 1030 6 - 335-405 -
KM 809 Gr 4 - 70 C 6 0.65-0.75 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1180-1420 1030 6 - 335-405 -
KM 810 Gr 5 - 75 C 6 0.7-0.8 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1180-1570 1080 6 - 335-450 -
KM 811 Gr 6 - 80 C 6 0.75-0.85 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1180-1570 1080 6 - 335-450 -
KM 812 Gr 7 - 85 C 6 0.8-0.9 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1180-1570 1080 6 - 335-450 -
KM 813 Gr 8 - 98 C 6 0.9-1.05 0.5-0.8 0.1-0.35 0.05 0.05 - - - - 1570-1760 1470 6 - 450-515 -
KM 814 Gr 9 - 55 Si 7 0.5-0.6 0.8-1.0 1.5-2.0 0.05 0.05 - - - - 1570-1960 1470 6 - 450-540 -
KM 815 Gr 10 - 50 Cr 4 0.45-0.55 0.6-0.9 0.1-0.35 0.05 0.05 0.9-1.2 - - - 1670-2260 1570 5 - 480-620 -
KM 816 Gr 11-50Cr4V2 0.45-0.55 0.5-0.8 0.1-0.35 0.05 0.05 0.9-1.2 - - V=0.15-0.3 1880-2360 1760 4 - 530-640 -
DIN 17221 Hot Rolled Spring Steels Suitable for Quenching & Tempering
KM 817 38 Si 7 0.35-0.42 0.5-0.8 1.5-1.8 0.03 0.03 - - - - - - - - 217 -
KM 818 54 Si Cr 6 0.51-0.59 0.5-0.8 1.2-1.6 0.03 0.03 0.5-0.8 - - - - - - - 248 -
KM 819 60 Si Cr 7 0.57-0.65 0.7-1.0 1.5-1.8 0.03 0.03 0.2-0.4 - - - - - - - 248 -
KM 820 55 Cr 3 0.52-0.59 0.7-1.0 0.25-0.5 0.03 0.03 0.7-1.0 - - - - - - - 248 -
KM 821 50 Cr V 4 0.47-0.55 0.7-1.0 0.15-0.4 0.03 0.03 0.9-1.2 - - V=0.1-0.2 - - - - 248 -
KM 822 51 Cr Mo V 4 0.48-0.56 0.7-1.0 0.15-0.4 0.03 0.03 0.9-1.2 0.15-0.25 - V=0.08-0.15 - - - - 248 -
DIN 17222 Cold Rolled Steel Strips for Springs

KM 823 C 55 0.52-0.60 0.6-0.9 0.15-0.35 0.045 0.045 - - - - 1150-1650 - - - 325-465 2
KM 824 C 60 0.57-0.65 0.6-0.9 0.15-0.35 0.045 0.045 - - - - 1180-1680 - - - 335-475 2
KM 825 C 67 0.65-0.72 0.6-0.9 0.15-0.35 0.045 0.045 - - - - 1230-1770 - - - 345-500 2.5
KM 826 C 75 0.7-0.8 0.6-0.8 0.15-0.35 0.045 0.045 - - - - 1320-1870 - - - 370-530 2.5
KM 827 Ck55 0.52-0.60 0.6-0.9 0.15-0.35 0.035 0.035 - - - - 1150-1650 - - - 325-465 2
KM 828 Ck 60 0.57-0.65 0.6-0.9 0.15-0.35 0.035 0.035 - - - - 1180-1680 - - - 335-475 2
KM 829 Ck 67 0.65-0.72 0.6-0.9 0.15-0.35 0.035 0.035 - - - - 1230-1770 - - - 345-500 2.5
KM 830 Ck 75 0.7-0.8 0.6-0.9 0.15-0.35 0.035 0.035 - - - - 1320-1870 - - - 370-530 2.5
KM 831 Ck 85 0.8-0.9 0.45-0.65 0.15-0.35 0.035 0.035 - - - - 1400-1950 - - - 395-550 2.5
KM 832 Ck 101 0.95-1.05 0.4-0.6 0.15-0.35 0.035 0.035 - - - - 1500-2100 - - - 425-590 2
KM 833 55 Si 7 0.52-0.6 0.7-1.0 1.5-1.8 0.045 0.045 - - - - 1300-1800 - - - 365-510 2
KM 834 71 Si 7 0.68-0.75 0.6-0.8 1.5-1.8 0.035 0.035 - - - - 1500-2200 - - - 425-620 3
KM 835 67 Si Cr 5 0.62-0.72 0.4-0.6 1.2-1.4 0.035 0.035 0.4-0.6 - - - 1500-2200 - - - 425-620 3
KM 836 50 Cr V 4 0.47-0.55 0.7-1.1 0.15-0.4 0.035 0.035 0.9-1.2 - - V=0.1-0.2 1400-2000 - - - 395-560 3
BS 970-2 Wrought Steels for Hot Formed Springs for Mechanical & Allied Engineering Purposes
KM 837 251 A 58 0.55-0.6 0.8-1.0 1.8-2.1 0.035 0.035 0.15-0.3 0.1 - - - - - - 321 max -
KM 838 251 A 60 0.57-0.62 0.8-1.0 1.8-2.1 0.035 0.035 0.25-0.4 0.12 - - - - - - 321 max -
KM 839 525 A 58 0.55-0.6 0.8-0.95 0.2-0.35 0.035 0.035 0.7-0.85 0.1 - - - - - - 321 max -
KM 840 525 A 60 0.57-0.62 0.85-1.0 0.2-0.35 0.035 0.035 0.8-0.95 0.06 min - - - - - - 321 max -
KM 841 525 A 61 0.57-0.63 0.85-1.0 0.2-0.35 0.035 0.035 0.85-1.0 0.08-0.15 - - - - - - 321 max -
KM 842 685 A 57 0.55-0.6 0.7-0.9 1.2-1.6 0.035 0.035 0.6-0.85 - - - - - - - 321 max -
KM 843 704 A 60 0.57-0.62 0.85-1.0 0.2-0.35 0.035 0.035 0.8-0.95 0.15-0.25 - - - - - - 321 max -
KM 844 705 A 60 0.57-0.62 0.85-1.0 0.2-0.35 0.035 0.035 0.85-1.0 0.25-0.35 - - - - - - 321 max -
KM 845 735 A 51 0.48-0.54 0.7-1.0 0.2-0.35 0.035 0.035 0.9-1.2 - - V=0.1-0.2 - - - - 321 max -
KM 846 735 A 54 0.52-0.57 0.9-1.15 0.2-0.35 0.035 0.035 1.05-1.2 - - V=0.12-0.2 - - - - 321 max -
KM 847 925 A 60 0.55-0.65 0.7-1.0 1.7-2.1 0.035 0.035 0.2-0.4 0.2-0.3 - - - - - - 321 max -
KM 848 251 H 60 0.56-0.64 0.7-1.0 1.6-2.2 0.035 0.035 0.4 0.12 - - - - - - 321 max -
KM 849 525 H 60 0.55-0.64 0.65-1.0 0.15-0.4 0.035 0.035 0.6-1.0 0.15 - - - - - - 321 max -
KM 850 685 H 57 0.54-0.62 0.5-0.8 1.2-1.6 0.035 0.035 0.5-0.8 - - - - - - - 321 max -
KM 851 704 H 60 0.55-0.64 0.65-1.1 0.15-0.4 0.035 0.035 0.6-1.0 0.15-0.25 - - - - - - 321 max -
KM 852 705 H 60 0.55-0.64 0.65-1.1 0.15-0.4 0.035 0.035 0.6-1.0 0.25-0.35 - - - - - 321 max -
KM 853 735 H 51 0.47-0.55 0.7-1.1 0.15-0.4 0.035 0.035 0.9-1.2 - - 0.1-0.25 - - - - 321 max -
KM 854 805 H 60 0.55-0.64 0.65-1.05 0.15-0.4 0.035 0.035 0.35-0.65 0.15-0.25 0.35-0.75 - - - - - 321 max -
EN 10084 CASE HARDENING STEELS

KM 901 C10E 0.07-0.13 0.3-0.6 0.4 0.035 0.035 - - - - - - - - 131 -
KM 902 C15E 0.12-0.18 0.3-0.6 0.4 0.035 0.035 - - - - - - - - 143 -
KM 903 C16E 0.12-0.18 0.6-0.9 0.4 0.035 0.035 - - - - - - - - 156 -
KM 904 17Cr3 0.14-0.20 0.6-0.9 0.4 0.035 0.035 0.7-1.0 - - - - - - - 174 -
KM 905 28Cr4 0.24-0.31 0.6-0.9 0.4 0.035 0.035 0.9-1.2 - - - - - - - 217 -
KM 906 16MnCr5 0.14-0.19 1.0-1.3 0.4 0.035 0.035 0.8-1.1 - - - - - - - 207 -
KM 907 20MnCr5 0.17-0.22 1.1-1.4 0.4 0.035 0.035 1.0-1.3 - - - - - - - 217 -
KM 908 18CrMo4 0.15-0.21 0.6-0.9 0.4 0.035 0.035 0.9-1.2 0.15-0.25 - - - - - - 207 -
KM 909 22CrMoS3-5 0.19-0.24 0.7-1.0 0.4 0.02-0.04 0.035 0.7-1.0 0.4-0.5 - - - - - - 217 -
KM 910 20MoCr3 0.17-0.23 0.6-0.9 0.4 0.035 0.035 0.4-0.7 0.3-0.4 - - - - - - 207 -
KM 911 20MoCr4 0.17-0.22 0.7-1.0 0.4 0.035 0.035 0.3-0.6 0.4-0.5 - - - - - - 207 -
KM 912 16NiCr4 0.13-0.19 0.7-1.0 0.4 0.035 0.035 0.6-1.0 - 0.8-1.1 - - - - - 217 -
KM 913 18NiCr5-4 0.16-0.21 0.6-0.9 0.4 0.035 0.035 0.9-1.2 - 1.2-1.5 - - - - - 223 -
KM 914 17CrNi6-6 0.14-0.19 0.4-0.6 0.4 0.035 0.035 1.4-1.7 - 1.4-1.7 - - - - - 229 -
KM 915 15NiCr13 0.12-0.18 0.4-0.7 0.4 0.035 0.035 0.6-0.9 - 3.0-3.5 - - - - - 229 -
KM 916 20NiCrMo2-2 0.17-0.23 0.65-0.95 0.4 0.035 0.035 0.35-0.7 0.15-0.25 0.4-0.7 - - - - - 212 -
KM 917 17NiCrMo6-4 0.14-0.20 0.6-0.9 0.4 0.035 0.035 0.8-1.1 0.15-0.25 1.2-1.5 - - - - - 229 -
KM 918 20NiCrMoS6-4 0.16-0.23 0.5-0.9 0.4 0.02-0.04 0.035 0.6-0.9 0.25-0.35 1.4-1.7 - - - - - 229 -
KM 919 18CrNiMo7-6 0.15-0.21 0.5-0.9 0.4 0.035 0.035 1.5-1.8 0.25-0.35 1.4-1.7 - - - - - 229 -
GB 12Cr1MoV 0.08-0.15 0.4-0.7 0.17-0.37 0.035 0.035 0.9-1.2 0.25-0.35 V-0.15-0.30 490 245 22
RIES INDIA LTD.
L. No.:1600-8
v. 0
RTIES
SUPPLY
CONDN.
As rolled
N/Asrolled
N/Asrolled
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A
A
A
A
-
-
-
-
-
-
-
-
A
N+T/Q+T
A
N+T/Q+T
A
N+T/Q+T
A
N+T/Q+T
A
N+T/Q+T
A
N+T/Q+T
A
N+T/Q+T
N+T/Q+T
-
-
-
-
-
-
As rolled
N
N
N
N
N
N
N
N
N
N
N
N
-
-
N
N
-
N
N
N
N
N
N
N
N
N
N
N
Q+T
Q+T
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
A/ N
A/ N
A/ N
A/ N
A/ N
A/ N
A/ N
A/ N
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
N/Q+T
N/Q+T
N/Q+T
H.T.
H.T.
H.T.
N
N
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
A/As Cast
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
Q+T(V II)
N
N
N
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q + T (1)
Q+T
Q+T
Q+T
A
A
A
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
Q+T
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
-
-
-
-
-
-
-
-
-
-
-
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
As Cast
-
-
-
-
-
-
-
-
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
H.T.
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Soln.Ann
Annl
Annl
Annl
Annl
Annl
Annl
Q+T
Q+T
A
A
A
A
A
Q+T
Q+T
Q+T
Q+T
A
A
A
Q+T
Q+T
Q+T
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
Soln Ann
N
N
N
N
N
N
N
N
H.R
H.R
H.R
H.R
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N /A
N /A
N /A
N /A
H.F/N
H.F/N
N
N
N+T
A
N+T
N+T
Soln treated
Soln treated
Soln treated
Soln treated
Soln treated
Soln treated
Solution
treated
N
N
N
N
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
ANN
ANN
ANN
ANN
ANN
ANN
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Q+T
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed

No. GRADE ALLOYING ELEMENTS * PERMISSIBLE IMPURITIES UTS YS ELONG IMPACT HDN CAST
DESIGNATION % Cu % Sn % Zn % Pb % Ni % Sb % Fe % Al % S, P N/mm2 N/mm2 % min J min BHN MODE
Others min min min
DIN 1705 Copper-Tin-Zinc Casting Alloys ( Tin Bronze & Gunmetal Castings )
KM 1001 G - CuSn 12 84.0-88.5 11.0-13.0 * 1.0 * 1.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.4 260 140 12 - 80 SAND
KM 1002 GZ - CuSn 12 84.0-88.5 11.0-13.0 * 1.0 * 1.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.4 280 150 5 - 95 CENTRI
KM 1003 GC - CuSn 12 84.0-88.5 11.0-13.0 * 1.0 * 1.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.4 280 140 8 - 90 CONT
KM 1004 G - CuSn 12 Ni 84.0-87.0 11.0-13.0 * 0.4 * 0.3 1.5-2.5 * 0.1 * 0.2 - * 0.05, 0.2 280 160 14 - 90 SAND
KM 1005 GZ - CuSn 12 Ni 84.0-87.0 11.0-13.0 * 0.4 * 0.3 1.5-2.5 * 0.1 * 0.2 - * 0.05, 0.2 300 180 8 - 100 CENTRI
KM 1006 GC - CuSn 12 Ni 84.0-87.0 11.0-13.0 * 0.4 * 0.3 1.5-2.5 * 0.1 * 0.2 - * 0.05, 0.2 300 170 10 - 90 CONT
KM 1007 G - CuSn 12 Pb 84.0-87.0 11.0-13.0 * 1.0 1.0-2.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.2 260 140 10 - 80 SAND
KM 1008 GZ - CuSn 12 Pb 84.0-87.0 11.0-13.0 * 1.0 1.0-2.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.2 280 150 5 - 90 CENTRI
KM 1009 GC - CuSn 12 Pb 84.0-87.0 11.0-13.0 * 1.0 1.0-2.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.2 280 140 7 - 85 CONT
KM 1010 G - CuSn 10 88.0-90.0 9.0-11.0 * 0.5 * 1.0 * 2.0 * 0.2 * 0.2 - * 0.05, 0.2 270 130 18 - 70 SAND
KM 1011 G - CuSn 10 Zn 86.0-89.0 9.0-11.0 1.0-3.0 * 1.5 * 2.0 * 0.3 * 0.25 - * 0.1, 0.05 260 130 15 - 75 SAND
KM 1012 G - CuSn 7 ZnPb 81.0-85.0 6.0-8.0 3.0-5.0 5.0-7.0 * 2.0 * 0.3 * 0.25 - * 0.1, 0.05 240 120 15 - 65 SAND
KM 1013 GZ-CuSn 7ZnPb 81.0-85.0 6.0-8.0 3.0-5.0 5.0-7.0 * 2.0 * 0.3 * 0.25 - * 0.1, 0.05 270 130 13 - 75 CENTRI
KM 1014 GC-CuSn 7ZnPb 81.0-85.0 6.0-8.0 3.0-5.0 5.0-7.0 * 2.0 * 0.3 * 0.25 - * 0.1, 0.05 270 120 16 - 70 CONT
KM 1015 G - CuSn 6 ZnNi 83.5-87.5 5.5-7.0 1.5-3.0 2.5-4.0 1.5-2.5 * 0.3 * 0.25 - * 0.1, 0.05 270 140 15 - 75 SAND
KM 1016 G - CuSn 5 ZnPb 84.0-86.0 4.0-6.0 4.0-6.0 4.0-6.0 * 2.5 * 0.3 * 0.3 - * 0.1, 0.05 220 90 16 - 60 SAND
KM 1017 G - CuSn 2 ZnPb 80.0-85.0 1.5-3.0 7.0-9.0 4.0-6.0 1.5-2.5 * 0.25 * 0.3 - * 0.1, 0.05 210 90 18 - 60 SAND
412704185.xls OF 45

Others min min min

As=0.05-0.2,
*Mn=0.1,
*Si=0.1,
KM 1018 G - CuZn 15 83.0-87.5 * 0.5 REST * 0.5 * 0.2 - * 0.15 * 0.02 *P=0.05 170 70 25 - 45 SAND
*Mn=0.2,
*Si=0.05,
KM 1019 G - CuZn 33 Pb 63.0-67.0 * 1.5 REST 1.0-3.0 * 1.0 - * 0.8 * 0.1 *P=0.05 180 70 12 - 45 SAND
*Mn=0.1,
*Si=0.1,
KM 1020 G - CuZn 37 Pb 59.0-63.0 * 0.7 REST 0.5-2.5 * 1.0 - * 0.5 0.2-0.8 *P=0.05 280 90 20 - 70 SAND
*Mn=0.1,
*Si=0.1,
KM 1021 GD - CuZn 37 Pb 59.0-63.0 * 0.7 REST 0.5-2.5 * 1.0 - * 0.5 0.2-0.8 *P=0.05 280 120 4 - 75 PRESS
*Mn=0.1,
*Si=0.1,
KM 1022 GK - CuZn 37 Pb 59.0-63.0 * 0.7 REST 0.5-2.5 * 1.0 - * 0.5 0.2-0.8 *P=0.05 280 90 20 - 70 GRAVITY
*Mn=0.5,
*Si=0.2,
KM 1023 G - CuZn 38 Al 59.0-64.0 * 0.1 REST * 0.1 * 1.0 - * 0.5 0.1-0.8 *P=0.05 380 130 20 - 75 SAND
*Mn=0.5,
*Si=0.2,
KM 1024 GK - CuZn 38 Al 59.0-64.0 * 0.1 REST * 0.1 * 1.0 - * 0.5 0.1-0.8 *P=0.05 380 130 20 - 75 GRAVITY
*Mn=2.5,
*Si=0.1,
KM 1025 G - CuZn 40 Fe 56.0-62.0 * 1.0 REST * 1.0 * 2.0 - 0.2-1.2 * 0.1 *P=0.05 300 130 15 - 75 SAND
*Mn=2.5,
*Si=0.1,
KM 1026 GZ - CuZn 40 Fe 56.0-62.0 * 1.0 REST * 1.0 * 2.0 - 0.2-1.2 * 0.1 *P=0.05 325 150 15 - 85 CENTRI
412704185.xls OF 45

Others min min min
*Mn=0.5,
*Si=0.6,
KM 1027 GK - CuZn 37 Al 1 60.0-64.0 * 0.5 REST * 0.5 * 2.0 * 0.1 * 0.5 0.3-1.8 *P=0.05 450 170 25 - 105 GRAVITY

*Si=0.1,
KM 1028 G - CuZn 35 Al 1 56.0-65.0 * 1.0 REST * 1.0 * 3.0 Mn=0.3-3 0.5-2.0 0.5-2.0 *P=0.05 450 170 20 - 110 SAND
*Si=0.1,
KM 1029 GZ - CuZn 35 Al 1 56.0-65.0 * 1.0 REST * 1.0 * 3.0 Mn=0.3-3 0.5-2.0 0.5-2.0 *P=0.05 500 200 18 - 120 CENTRI
*Si=0.1,
KM 1030 GK - CuZn 35 Al 1 56.0-65.0 * 1.0 REST * 1.0 * 3.0 Mn=0.3-3 0.5-2.0 0.5-2.0 *P=0.05 475 200 18 - 110 GRAVITY
*Si=0.1,
*Si=0.1,
*Si=0.1,
*Si=0.1,
*Si=0.1,
*Si=0.1,
*Mn=0.2 *
KM 1037 G - CuZn 15 Si 4 78.0-83.0 * 0.3 REST * 0.8 * 1.0 Si=3.8-5.0 * 0.6 * 0.1 P=0.03 400 230 10 - 100 SAND
*Mn=0.2 *
KM 1038 GD - CuZn 15 Si 4 78.0-83.0 * 0.3 REST * 0.8 * 1.0 Si=3.8-5.0 * 0.6 * 0.1 P=0.03 550 300 8 - 125 PRESS
*Mn=0.2 *
KM 1039 GK - CuZn 15 Si 4 78.0-83.0 * 0.3 REST * 0.8 * 1.0 Si=3.8-5.0 * 0.6 * 0.1 P=0.03 500 300 10 - 120 GRAVITY
412704185.xls OF 45

Others min min min

*Mn = 1.0,
KM 1040 G - CuAl 10 Fe 83.0 * 0.3 * 0.5 * 0.2 * 3.0 - 2.0-4.0 8.0-11.0 *Si = 0.2 500 180 15 - 115 SAND
*Mn = 1.0,
KM 1041 GK - CuAl 10 Fe 83.0 * 0.3 * 0.5 * 0.2 * 3.0 - 2.0-4.0 8.0-11.0 *Si = 0.2 550 200 25 - 115 CHILL
*Mn = 1.0,
KM 1042 GZ - CuAl 10 Fe 83.0 * 0.3 * 0.5 * 0.2 * 3.0 - 2.0-4.0 8.0-11.0 *Si = 0.2 550 200 15 - 115 CENTRI
*Mn =2.5,
*Si= 0.1,
KM 1043 G - CuAl 9 Ni 82.0 * 0.2 * 0.5 * 0.05 1.5-4.0 - 1.0-3.0 8.5-10.0 *Mg=0.05 500 200 20 - 110 SAND
*Mn =2.5,
*Si= 0.1,
KM 1044 GK - CuAl 9 Ni 82.0 * 0.2 * 0.5 * 0.05 1.5-4.0 - 1.0-3.0 8.5-10.0 *Mg=0.05 530 230 20 - 120 CHILL
*Mn =2.5,
*Si= 0.1,
KM 1045 GZ - CuAl 9 Ni 82.0 * 0.2 * 0.5 * 0.05 1.5-4.0 - 1.0-3.0 8.5-10.0 *Mg=0.05 600 250 20 - 120 CENTRI
*Mn =3.0,
*Si= 0.1,
*Mn =3.0,
*Si= 0.1,
*Mn =3.0,
*Si= 0.1,
412704185.xls OF 45

DESIGNATION % Cu % Sn % Zn % Pb % Ni % Sb % Fe % Al % S, P N/mm 2
N/mm 2
% min J min BHN MODE
Others min min min
*Mn =3.0,
*Si= 0.1,
KM 1049 GC - CuAl 10 Ni 76.0 * 0.2 * 0.5 * 0.05 4.0-6.5 - 3.5-5.5 8.5-11.0 *Mg=0.05 700 300 13 - 160 CONT
*Mn =2.5,
*Si= 0.1,

*Mn =2.5,
*Si= 0.1,
*Mn =2.5,
*Si= 0.1,
Mn=5-6.5,
KM 1053 G - CuAl 8 Mn 82.0 * 0.2 * 0.5 * 0.1 1.0-2.0 - * 1.5 7.0-9.0 *Si=0.1 440 180 18 - 105 SAND
Mn=5-6.5,
KM 1054 GK - CuAl 8 Mn 82.0 * 0.2 * 0.5 * 0.1 1.0-2.0 - * 1.5 7.0-9.0 *Si=0.1 450 200 30 - 105 CHILL
IS 318 Leaded Tin Bronze Ingots and Castings

max max
KM 1055 LTB 1 REST 6.0-8.0 1.5-3.0 2.5-3.5 * 2.0 * 0.3 * 0.3 * 0.01 * Si=0.01 250 130 16 - - SAND
KM 1056 LTB 2 REST 4.0-6.0 4.0-6.0 4.0-6.0 * 2.0 * 0.4 * 0.35 * 0.01 * Si=0.02 190 100 13 - - SAND
KM 1057 LTB 3 REST 6.0-8.0 * 0.75 9.0-11.0 * 2.0 * 0.5 * 0.35 * 0.01 * Si=0.02 175 75 4 - - SAND
KM 1058 LTB 4 REST 6.0-8.0 * 0.75 14.0-16.0 * 2.0 * 0.5 * 0.35 - * Si=0.02 160 70 4 - - SAND
KM 1059 LTB 5 REST 9.0-11.0 * 1.0 8.5-11.0 * 2.0 * 0.5 * 0.35 * 0.01 * Si=0.02 190 80 5 - - SAND
KM 1060 LTB 6 REST 4.0-6.0 * 1.0 18.0-23.0 * 2.0 * 0.5 * 0.35 - * Si=0.01 140 60 5 - - SAND
IS 305 Aluminium Bronze Ingots and Castings
412704185.xls OF 45

Others min min min
Mn<1.0,
Si<0.25, SAND
KM 1061 GRADE AB 1 REST 0.1 max 0.5 max 0.05 max 1.0 max - 1.5-3.5 8.5-10.5 Mg<0.05 500 170 18 - - CAST
Mn<1.5,
Si<0.1, SAND
KM 1062 GRADE AB 2 REST 0.1 max 0.5 max 0.05 max 4.0-5.5 - 4.0-5.5 8.8-10.0 Mg<0.05 640 250 13 - - CAST
IS 306 Tin Bronze Ingots and Castings

Si<0.02, SAND
KM 1063 Ingots REST 9.5-10.5 1.75-3.25 1.5 max 1.0 max - 0.15 max 0.01 max Bi<0.03 260 120 13 - - CAST
Si<0.02, SAND
KM 1064 Castings REST 9.5-10.5 1.5-3.0 1.5 max 1.0 max - 0.15 max 0.01 max Bi<0.03 260 120 13 - - CAST
IS 25 Antifriction Bearing Alloys

KM 1065 GRADE 90 2.5-3.5 90.0 min * 0.008 0.3 max - 6.5-7.5 * 0.08 * 0.005 As,Bi,Cd - - - - -
KM 1066 GRADE 84 5.0-6.0 84.0 min * 0.008 0.3 max - 9.0-11.0 * 0.08 * 0.005 As,Bi,Cd - - - - -
KM 1067 GRADE 75 2.75-3.25 74.0-76.0 * 0.008 REST - 10.0-12.0 * 0.08 * 0.005 As,Bi,Cd - - - - -
KM 1068 GRADE 69 1.0-1.4 68.0-70.0 29.0-31.0 0.3 max - 0.2 max * 0.1 * 0.005 As,Bi,Cd - - - - -
As .3-0.8
KM 1072 GRADE 6 0.8-1.2 5.0-7.0 * 0.05 REST 0.8-1.5 14.0-16.0 * 0.1 * 0.05 Cd 0.7-1.5 - - - - -
KM 1074 GRADE 1 0.5 max 0.75-1.25 * 0.01 REST - 15.0-16.0 * 0.1 * 0.005 As=0.8-1.1 - - - - -
412704185.xls OF 45

Others min min min
P=0.4-1.0, SAND
KM 1075 PB4 REST 9.5-11.0 0.5 max 0.75 max 0.5 max - - - S<0.1 190 100 3 - - CAST
P>0.3, SAND
KM 1076 LPB1 REST 6.5-8.5 2.0 max 2.0-5.0 1.0 max 0.25 max - - S<0.1 190 80 3 - - CAST
P<0.1,
S<0.1,
Mn<0.2, SAND
KM 1077 LB2 REST 9.0-11.0 1.0 max 8.5-11.0 2.0 max 0.5 max 0.15 max 0.01 max Si<0.02 190 80 5 - - CAST

P<0.1,
S<0.1,
Mn<0.2, SAND
KM 1078 LB4 REST 4.0-6.0 2.0 max 8.0-10.0 2.0 max 0.5 max 0.25 max 0.01 max Si<0.02 160 60 7 - - CAST
Bi<0.1,
S<0.1, SAND
KM 1079 LG1 REST 2.0-3.5 7.0-9.5 4.0-6.0 2.0 max - - 0.01 max Si<0.02 180 80 11 - - CAST
Bi<0.05, SAND
KM 1080 LG2 REST 4.0-6.0 4.0-6.0 4.0-6.0 2.0 max - - 0.01 max Si<0.02 200 100 13 - - CAST
KM 1081 SCB1 70.0-80.0 1.0-3.0 REST 2.0-5.0 1.0 max - 0.75 max 0.01 max - - - - - - SAND
P<0.05,
Mn<0.2, SAND
KM 1082 SCB3 63.0-67.0 1.5 max REST 1.0-3.0 1.0 max - 0.75 max 0.1 max Si<0.05 - - - - - CAST
KM 1083 SCB6 83.0-88.0 - REST 0.5 max - - - As=0.05-0.2 - - - - - SAND
KM 1084 DCB1 59.0-63.0 - REST 0.25 max - - - 0.5 max - - - - - - SAND
Mn<0.5, SAND
KM 1085 DCB3 58.0-63.0 1.0 max REST 0.5-2.5 1.0 max - 0.8 max 0.2-0.8 Si<0.05 - - - - - CAST
KM 1086 PCB1 57.0-60.0 0.5 max REST 0.5-2.5 - - 0.3 max 0.5 max - - - - - - SAND
412704185.xls OF 45

DESIGNATION % Cu % Sn % Zn % Pb % Ni % Sb % Fe % Al % S, P N/mm 2
N/mm 2
% min J min BHN MODE
Others min min min
KM 1087 HCC1 - - - - - - - - - Resistivity values only to be specified.
KM 1088 CC1-TF REST - - - - - - - Cr=0.5-1.25 - - - - - SAND
P=0.5-1.0,
S<0.05,
Mn<0.05, SAND
KM 1089 PB1 REST 10.0-11.5 0.05 max 0.25 max 0.1 max 0.05 max 0.1 max 0.01 max Si<0.02 220 130 3 - - CAST
P0.15-0.6
S<0.1, SAND
KM 1090 PB2 REST 11.0-13.0 0.3 max 0.5 max 0.5 max - 0.1 max 0.01 max Si<0.05 220 130 5 - - CAST

P<0.15,
S<0.05,
Mn<0.2, SAND
KM 1091 CT1 REST 9.0-11.0 0.03 max 0.25 max 0.25 max 0.2 max 0.2 max 0.01 max Si<0.01 240 130 - - - CAST
As<0.15,
Si<0.01. SAND
KM 1092 LG4 REST 6.0-8.0 1.5-3.0 2.5-3.5 2.0 max 0.25 max 0.2 max 0.01 max Bi<0.05 250 130 16 - - CAST
Mg<0.05,
Mn<1.0, SAND
KM 1093 AB1 REST 0.1 max 0.5 max 0.03 max 1.0 max - 1.5-3.5 8.5-10.5 Si<0.2 500 170 18 - - CAST
Mg<0.05,
Mn<3.0, SAND
KM 1094 AB2 REST 0.1 max 0.5 max 0.03 max 4.0-5.5 - 4.0-5.5 8.8-10.0 Si<0.1 640 250 13 - - CAST
P<0.05,
Mn<11-15, SAND
KM 1095 CMA1 REST 0.5 max 1.0 max 0.05 max 1.5-4.5 - 2.0-4.0 7.0-8.5 Si<0.15 650 280 18 - - CAST
Mn=0.1-3, SAND
KM 1096 HTB1 57.0 min 1.0 max REST 0.5 max 1.0 max - 0.7-2.0 0.5-2.5 Si<0.1 470 170 18 - - CAST
412704185.xls OF 45

Others min min min
Mn<4.0, SAND
KM 1097 HTB3 55.0 min 0.2 max REST 0.2 max 1.0 max - 1.5-3.25 3.0-6.0 Si<0.1 740 400 11 - - CAST
P<0.1
S<0.1, SAND
KM 1098 LB1 REST 8.0-10.0 1.0 max 13.0-17.0 2.0 max 0.5 max - - Si<0.02 170 80 4 - - CAST
P<0.1 SAND
KM 1099 LB5 REST 4.0-6.0 1.0 max 18.0-23.0 2.0 max 0.5 max - - Si<0.01 160 60 5 - - CAST
S<0.1,
Si<0.02, SAND
KM 1100 G1 REST 9.5-10.5 1.75-2.75 1.5 max 1.0 max - 0.15 max 0.01 max Bi<0.03 270 130 13 - - CAST

P<0.02
S<0.1,
Si<0.02, SAND
KM 1101 G3 REST 6.5-7.5 1.5-3.0 0.1-0.5 5.25-5.75 - - 0.01 max Bi<0.02 280 140 16 - - CAST
P<0.02
S<0.1,
Si<0.02, SAND
KM 1102 G3-TF REST 6.5-7.5 1.5-3.0 0.1-0.5 5.25-5.75 - - 0.01 max Bi<0.02 430 280 3 - - CAST
KM 1103 SCB4 60.0-63.0 1.0-1.5 REST 0.5 max - - - 0.01 max - - - - - - SAND
P.05-0.4,
S<0.05,
Mn<0.2, SAND
KM 1104 CT2 85.0-87.5 11.0-13.0 0.4 max 0.3 max 1.5-2.5 - 0.2 max 0.01 max Si<0.01 280 160 12 - - CAST
Mg<0.05,
Mn<0.5, SAND
KM 1105 AB3 REST 0.1 max 0.4 max 0.03 max 0.1 max - 0.5-0.7 6.0-6.4 Si<2-2.4 460 180 20 - - CAST
412704185.xls OF 45

Others min min min
P<0.005,
Mn=0.4-1,
Si,0.2-0.4
Bi<0.002,
S<0.01,
C<0.02,
Cr=1.5-2,
Zr=0.05-
0.15 SAND
KM 1106 CN1 REST - - 0.005 max 29-33 - 0.4-1.0 - Co<0.05 480 300 18 - - CAST
P<0.005,Mn
=1.0-
1.4,Si=0.2-
0.4
Bi<0.002,S<
0.01,
C<0.02,
Nb+Ta= 1.2-
1.4, SAND
KM 1107 CN2 REST - - 0.005 max 28-32 - 1.0-1.4 - Co<0.05 480 300 18 - - CAST
412704185.xls OF 45

Others min min min
412704185.xls OF 45
412704185.xls OF 45
Division 6. TYPICAL APPLICATIONS AND HEAT TREATMENT Rev : 0
MATL NO. DESIGNATION HEAT TREATMENT TYPE TYPICAL APPLICATIONS INTERNAL SPEC NO.
IS 2062
KM 101 Grade A As rolled for all thicknesses } Weldable quality structurals,plates,round bars,frames,chutes
KM 102 Grade B As rolled <12 thk. N for > 12 thk (if agreed) } Shafts & Shackles of Garland Idlers 1602-B-00066
KM 103 Grade C As rolled< 12 thk. N for thk > 12 mm } Better weldability and impact resistance.
IS 1570-1
KM 104 Fe 290 As rolled, Annealed, Normalised, Q + T, etc Plates, Bars,Tubes, Sections, Forgings, etc.
KM 105 FeE 220 As rolled, Annealed, Normalised, Q + T, etc Plates, Bars,Tubes, Sections, Forgings, etc.
412704185.xls 118 OF 155

IS 1079
KM 126 Gr O Hot rolled / Descaled / A / N ( as agreed ) Structurals , and plates for Gen Engg purposes
KM 127 Gr D Hot rolled / Descaled / A / N ( as agreed ) Drawing quality plates .
KM 128 Gr DD Hot rolled / Descaled / A / N ( as agreed ) Deep Drawing quality for Deck plates and Roller cups
KM 129 Gr EDD Hot rolled / Descaled / A / N ( as agreed ) Extra Deep Drawing quality plates
KM 130 Gr St 34 Hot rolled / Descaled / A / N ( as agreed ) Structurals , and plates for Gen Engg purposes
IS 513
KM 134 Gr O Annealed / Skin pass rolled Low carbon Sheets and Strips
KM 135 Gr D Annealed / Skin pass rolled Low carbon Sheets and Strips for drawing applications.
KM 136 Gr DD Annealed / Skin pass rolled Low carbon Sheets and Strips for deep drawing applications.
KM 137 Gr EDD Annealed / Skin pass rolled Low carbon Sheets and Strips for extra deep drawing applications
EN 10025
KM 138 S185 As rolled / A / N ( as agreed ) Ordinary Structurals and plates
KM 139 S235JR As rolled / A / N ( as agreed ) Structurals and plates - weldable quality.
KM 140 S235JRG1 As rolled / A / N ( as agreed )
KM 141 S235JRG2 As rolled / A / N ( as agreed )
KM 142 S235J0 As rolled / A / N ( as agreed )
KM 143 S235J2G3 Normalised Kiln & Mill Shell plates
KM 144 S235J2G4 As rolled / A / N ( as agreed )
KM 145 S275JR As rolled / A / N ( as agreed )
KM 147 S275J2G3 Normalised
KM 149 S355JR As rolled / A / N ( as agreed )
412704185.xls 119 OF 155

KM 151 S355J2G3 Normalised High strength structurals,Polycom parts, Arms of paddle feeder 1602-B-00025
KM 153 S355K2G3 Normalised
KM 154 S355K2G4 As rolled / A / N ( as agreed )
KM 155 E 295 As rolled / A / N ( as agreed ) Kiln drive shaft
KM 156 E 335 As rolled / A / N ( as agreed ) Support roller axle - Cement.
KM 157 E 360 As rolled / A / N ( as agreed ) High strength structurals, weldable, round bars.
KM 158 ASTM-A-36M
ASTM-A-283M
KM 159 Grade A
KM 160 Grade B
KM 161 Grade C
KM 162 Grade D
ASTM-A-285M
KM 163 Grade A
KM 164 Grade B
KM 165 Grade C
KM 166 ASTM-A-299M
KM 167 ASTM-A-366M
ASTM-A-387M
KM 168 Grade 2
KM 169 Grade 12
KM 170 Grade 11
KM 171 Grade 22
KM 172 Grade 21
412704185.xls 120 OF 155

KM 173 Grade 5
KM 174 Grade 9
KM 175 Grade 91
ASTM-A-569M
KM 176 Type A
KM 177 Type B
KM 178 Type C
ASTM-A-573M
KM 179 Grade 58
KM 180 Grade 65
KM 181 Grade 70
ASTM-A-612M
KM 182 ASTM-A-612M
412704185.xls 121 OF 155

EN 10028-3
KM 183 P275N Normalised, Control Cooled Structurals,Micro Alloyed, Fine-grained, weldable steels
KM 184 P275NH Normalised, Control Cooled High temperature applications
KM 185 P275NL1 Normalised, Control Cooled Low temperature applications
KM 186 P275NL2 Normalised, Control Cooled Special low temperature applications
EN 10113-2
KM 195 S275N
KM 196 S275NL
KM 197 S355N
KM 198 S355NL
KM 199 S460N
KM 200 S460NL
412704185.xls 122 OF 155


IS 1570
KM 201 20 C 8 A, N, Q+T ( others as per IS standard ) Forged and rolled bars / profiles
KM 207 40 C 8 A, N, Q+T ( others as per IS standard ) Forged shafts for Sugar Mill, Sprocket, Tail bar etc
KM 208 45 C 8 A, N, Q+T ( others as per IS standard ) Forged shafts for Sugar Mill, Sprocket, Tail bar etc
KM 209 50 C 4 A, N, Q+T ( others as per IS standard ) Forged and rolled products
IS 1875
KM 215 14 C 6 Normalised, Control Cooled Rolled products
KM 216 15 C 8 Normalised, Control Cooled Pins for Swing & Fixed frames of Cooler,Rotating parts of Sepol
KM 219 30 C 8 Normalised, Control Cooled Forged and rolled products
412704185.xls 123 OF 155

KM 221 45 C 8 Normalised, Control Cooled Forged spindle for Sugar Centrifugal m/c 1609-S-001
BS 970
KM 224 080 M 40 (En8) N, Q+T ( others as per BS standard ) Parts of Disagglomerator,Roller mill,Polycom,Double flap,Silo
Sugar mill gearing shafts,Drive & driven sprockets,Tie bars
KM 225 070 M 55 (En9) N, Q+T ( others as per BS standard ) Parts of Cooler in Cement plant.
KM 226 709 M 40 (En19) N, Q+T ( others as per BS standard ) Forged and rolled products,pins,axles
KM 227 817 M 40 (En24) N, Q+T ( others as per BS standard ) Forged & rolled,rotor shafts,hammers,Sugar mill house pin
EN 10083
KM 228 C22 A, N, Q+T ( others as per EN standard ) Forged shafts and rolled bars / profiles
KM 229 C22E A, N, Q+T ( others as per EN standard ) Forged shafts and rolled bars / profiles
KM 230 C22R A, N, Q+T ( others as per EN standard ) Forged shafts and rolled bars / profiles
KM 237 C35 A, N, Q+T ( others as per EN standard ) Shafts, Pins, etc.
KM 238 C35E A, N, Q+T ( others as per EN standard ) Kiln Base frame,inlet,outlet,Pendulum flap of preheater. 1601-B-00027, 1603-B-00024
KM 239 C35R A, N, Q+T ( others as per EN standard ) Shafts, Pins, etc.
KM 240 C40 A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 241 C40E A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 242 C40R A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 243 C45 A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
412704185.xls 124 OF 155

1601-B-00027,1602-B-00024,00026
Sprockets for Drag chain, Cooler, RAL, Support roller axle, Drive 1603-B-00007, 00029,
KM 244 C45E A, N, Q+T ( others as per EN standard ) shaftThrust roller, Cooler mechanical drive, DBC, Sepol parts etc 1604-B-00051, 1607-B-00049
KM 245 C45R A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 246 C50 A, N, Q+T ( others as per EN standard ) Forged and rolled products
KM 247 C50E A, N, Q+T ( others as per EN standard ) Forged and rolled products
KM 248 C50R A, N, Q+T ( others as per EN standard ) Forged and rolled products
KM 250 C55E A, N, Q+T ( others as per EN standard ) Forged and rolled products 1601-B-00027
KM 253 C60E A, N, Q+T ( others as per EN standard ) Forged and rolled products 1601-B-00027, 1602-B-00029
KM 255 28Mn6 A, N, Q+T ( others as per EN standard ) Forged and rolled products
EN 10083-2
KM 256 38Cr2 A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 257 46Cr2 A, N, Q+T ( others as per EN standard )
KM 260 41Cr4 A, N, Q+T ( others as per EN standard ) CSK bolts for Ball Mill Liners,Forged Gear blanks in CSD. 1603-B-00013,1604-B-00054
KM 261 25CrMo4 A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
KM 262 34CrMo4 A, N, Q+T ( others as per EN standard ) Forged / Rolled shafts, bars, axles.
1601-B-00027,00037,1602-B-00030
KM 263 42CrMo4 A, N, Q+T ( others as per EN standard ) Studs for tie rod anchorage in Cement,Hammers for CSD. 1604-B-00052,00053
KM 264 42CrMoS4 A, N, Q+T ( others as per EN standard ) High strength forgings and shafts
KM 265 50CrMo4 A, N, Q+T ( others as per EN standard ) High strength forgings and shafts
KM 266 36CrNiMo4 A, N, Q+T ( others as per EN standard ) High strength forgings and shafts
KM 267 34CrNiMo6 A, N, Q+T ( others as per EN standard ) High strength forgings and shafts
412704185.xls 125 OF 155

1601-B-00102, 1602-B-00065, 1603-
KM 268 30CrNiMo8 A, N, Q+T ( others as per EN standard ) Cement Mill Pinion B-00025,00031
KM 269 36NiCrMo16 A, N, Q+T ( others as per EN standard ) Spring steel for Cement cooler & Sepol.
KM 270 51CrV4 A, N, Q+T ( others as per EN standard ) High strength forgings and shafts
ASTM-A-108
KM 271 1010
KM 272 1015
KM 273 1020
KM 274 1025
KM 275 1030
KM 276 1035
KM 277 1040
KM 278 1045
KM 279 1050
KM 280 1118
KM 281 1141
KM 282 1211
KM 283 1215
ASTM-A-322
KM 284 1330
KM 285 1340
KM 286 4023
KM 287 4047
KM 288 4130
KM 289 4140
KM 290 4320
412704185.xls 126 OF 155

KM 291 4615
KM 292 4720
KM 293 4815
KM 294 5120
KM 295 5140
KM 296 6150
KM 297 8640
KM 298 8645
KM 299 8720
KM 300 9260
6.3 CARBON STEEL CASTINGS
IS 276
KM 301 Grade 1 Quenched ( solution annealed ) Austenitic Manganese steel with high impact strength 1604-B-00005,00006
KM 303 Grade 3 Quenched ( solution annealed ) Drag chain links,Ball-mill liners ( cement ) 1603-B-00006,1604-B-00005,00006
KM 304 Grade 4 Quenched ( solution annealed ) Impact plates, Hammers, Grate bars, ( cement + sugar ) 1604-B-00005,00006
IS 1030
KM 306 200-400 N A, N, N+T Carbon steel castings for general engineering purposes
KM 307 200-400 W A, N, N+T Mechanical drive of cooler ( cement ), Coupling ( Centrifugal )
KM 308 230-450 N A, N, N+T Sepol ( cement )
KM 309 230-450 W A, N, N+T Bearing blocks,brg cover,brg caps ( CSD )
KM 310 280-520 N A, N, N+T Nozzle ring of coal mill,pillow blocks,sheaves,pulley end disk 1604-B-00008, 1609-S-002
KM 311 280-520 W A, N, N+T Head stock,trash beam,gear hub,sprockets ( sugar mills ) 1604-B-00008
KM 312 340-570 N A, N, N+T Kiln base frame
KM 313 340-570 W A, N, N+T Hub for centrifugals
IS 2644
412704185.xls 127 OF 155

KM 314 CS 640 Any suitable h.t.to achieve mech props Polycom feed hopper, Coupling flange ( CSD )
KM 315 CS 700 Any suitable h.t.to achieve mech props Sugar mill gear rim, pinion, 1607-B-00144
KM 316 CS 840 Any suitable h.t.to achieve mech props Sugar mill drive pinion 1607-B-00144
KM 317 CS 1030 Any suitable h.t.to achieve mech props
KM 318 CS 1230 Any suitable h.t.to achieve mech props
IS 2707
KM 319 IS 2707 Gr 1 Any suitable h.t.to achieve mech props DBC ( cement ),End disk, Return roller ( CSD )
KM 320 IS 2707 Gr 2 Any suitable h.t.to achieve mech props Traction wheel ( CSD )
KM 321 IS 2707 Gr 3 Any suitable h.t.to achieve mech props Wheels for Paddle feeder
IS 2708
KM 322 IS 2708 Gr 1 A, N, N + T, Q + T. Disagglomerator,
KM 323 IS 2708 Gr 2 A, N, N + T, Q + T. Polycom pressure beam, Sugar mill gear & Crown wheels. 1603-B-00015,1607-B-00144
KM 324 IS 2708 Gr 3 A, N, N + T, Q + T. Fibrizer Hammers, Sugar mill Pinions 1607-B-00144,00145
IS 2856
KM 325 IS 2856 Gr 1 Any suitable h.t.to achieve mech props } Welding Quality Carbon steel castings
KM 326 IS 2856 Gr 2 Any suitable h.t.to achieve mech props } for Pressure containing parts
KM 327 IS 2856 Gr 3 Any suitable h.t.to achieve mech props } suitable for high temperature service
DIN 1681
1601-B-00026, 00049,
KM 328 GS - 38 As cast,Annealed 1602-B-00020, 00070
1601-B-00026, 00049,
KM 329 GS - 45 As cast,Annealed Roller mill,Trunnion bearing,drive (cement) 1602-B-00020, 00070
1601-B-00026, 00049,
KM 330 GS - 52 As cast,Annealed Hydraulic roller,Chain sprocket (cement),End disk pulleys 1602-B-00001, 00020, 00070
1601-B-00026,00049,
KM 331 GS - 60 As cast,Annealed Mechanical thruster,Kiln burner (cement) Tripper wheels 1602-B-00020,0070,1603-B-00040
DIN 17182
412704185.xls 128 OF 155

KM 332 GS-16Mn5 Normalised
1601-B-00026,00049,
KM 333 GS-20Mn5 Normalised or Q + T Cement Mill head,Cooler,Disagglomerator,Rotor disk,Hub . 1602-B-00020,0070,1604-B-00003
ASTM-A-27M
KM 334 N-1 As Cast
KM 335 N-2 Annealed, Normalised, Quench & Temper
KM 336 U-60-30 As Cast
KM 337 60-30 Annealed, Normalised, Quench & Temper
ASTM-A-128M
KM 341 A Quenched ( solution annealed )
KM 342 B-1 Quenched ( solution annealed )
KM 346 C Quenched ( solution annealed )
KM 347 D Quenched ( solution annealed )
KM 348 E-1 Quenched ( solution annealed )
KM 349 E-2 Quenched ( solution annealed )
KM 350 F Quenched ( solution annealed )
ASTM-A-148M
KM 351 80 - 40 Annealed, Normalised, Quench & Temper
412704185.xls 129 OF 155

ASTM-A-216M
KM 363 WCA Annealed / Normalised
KM 364 WCB Annealed / Normalised
KM 365 WCC Annealed / Normalised
IS 4522
KM 401 Grade 1 As cast,Annealed,Normalised, Q + T. Furnace parts-hearth plates,door frames,refinery fittings
KM 402 Grade 2 As cast,Annealed Incinerating retorts, tuyeres etc.
KM 403 Grade 3 As cast,Annealed Stirring blades-high degree of wear at high temperatures
KM 404 Grade 4 As cast,Annealed,Normalised, Q + T. Grate plates,refractory holders,kiln outlet,inlet tray.
KM 405 Grade 5 As cast,Annealed,Normalised, Q + T. Burnishing and coating rolls, furnace dampers
KM 406 Grade 6 As cast,Annealed,Normalised, Q + T. Ore roasting equipment,furnace conveyors, recuperators
KM 407 Grade 7 As cast,Annealed,Normalised, Q + T. Kiln outlet, Grate plates.
KM 408 Grade 8 As cast,Annealed,Normalised, Q + T. Case hardening boxes, worm retorts
KM 409 Grade 9 As cast,Annealed,Normalised,Q+T,Aging Grate plates
KM 410 Grade 10 As cast,Annealed,Normalised, Q + T. Radiant tubes,furnace skids, enamelling furnace fixtures.
KM 411 Grade 11 As cast,Annealed,Normalised,Q+T,Aging Furnace beams,pier caps
KM 412 Grade 12 As cast,Annealed Load bearing parts of a fnc-hearth plates,lead & salt pots
KM 413 Grade 13 As cast,Annealed,Normalised, Q + T. Gas dissociation equipment
KM 414 Grade 14 As cast,Annealed,Normalised, Q + T. Quenching fixtures,heat treating boxes,case hardening eqpt.
412704185.xls 130 OF 155

DIN 17205
KM 415 GS - 30 Mn 5 Quenched and Tempered Kiln Tyres, Supporting rollers.(cement) 1603-B-00022
KM 416 GS - 25CrMo4 Quenched and Tempered Head for 6 wheel bogie, 1602-B-00020, 00070
KM 417 GS - 34CrMo4 Quenched and Tempered Kiln girth gear. 1603-B-00023
1601-B-00026,00055,
1602-B-00020,00031,00055,00070
1603-B-00026,00043,
KM 418 GS - 42CrMo4 Quenched and Tempered Bogie wheels,Support rollers,Wagon tippler(MHE),Swing frame 1604-B-00009,00010,00011,00121
KM 419 GS-30CrMoV6 4 Quenched and Tempered Hammers,Impact plates,Eccentric discs,
KM 420 GS-35CrMoV10 4 Quenched and Tempered Mill girth gear. 1603-B-00028
KM 421 GS-25CrNiMo4 Quenched and Tempered Heat treatable alloy steel castings
KM 422 GS-34CrNiMo6 Quenched and Tempered Heat treatable alloy steel castings
KM 423 GS-30NiCrMo8 5 Quenched and Tempered Heat treatable alloy steel castings
KM 424 GS-33NiCrMo7 4 4 Quenched and Tempered Heat treatable alloy steel castings
EN 10213
KM 425 GP240GR
KM 426 GP240GH Normalised Heat treatable alloy steel castings
KM 427 GP280GH
KM 428 G20Mo5 Quenched and Tempered Ferritic steel castings with elevated temperature properties.
KM 429 G17CrMo5-5 Quenched and Tempered Grate plate girder,Brackets for Cooler.
KM 430 G17CrMo9-10 Quenched and Tempered Ferritic steel castings with elevated temperature properties.
KM 431 G12MoCrV5-2
KM 432 G17CrMoV5-10 Quenched and Tempered Ferritic steel castings for high temperature applications.
KM 433 GX15CrMo5
KM 434 GX8CrNi12 Quenched and Tempered Ferritic steel castings for high temperature applications.
KM 435 GX4CrNi13-4
KM 436 GX23CrMoV12-1 Quenched and Tempered Ferritic steel castings for high temperature applications.
KM 437 GX4CrNiMo16-5-1
DIN 17465
412704185.xls 131 OF 155

KM 438 GX30CrSi6 Annealed Cooler grate plates. 450-512025E
KM 439 GX40CrSi13 Annealed Grate bars of Clinker Crusher.
KM 440 GX40CrSi17 Annealed Heat resisting alloy steel castings
KM 441 GX40CrSi23 As Cast Heat resisting alloy steel castings
KM 442 GX40CrSi29 As Cast Heat resisting alloy steel castings
KM 443 GX130CrSi29 Annealed / Quenched + Tempered Throttle flap,Calcinator burner nozzle-Cement 1603-B-00037
KM 444 GX40CrNiSi27-4 As Cast Dip tubes,Pendulum flaps,Refractory holders,Kiln inlet 1603-B-00033,00038
KM 445 GX25CrNiSi18-9 As Cast Heat resisting alloy steel castings
KM 447 GX25CrNiSi 20-14 As Cast Throttle flap of TA duct ( cement ). 1603-B-00036
KM 448 GX40CrNiSi25-12 As Cast Grate plates of cooler. 1603-B-00041 , 450-512025E
KM 450 GX40NiCrSi38-18
KM 451 GX40NiCrSi35-25
KM 452 GX30CrNiSiNb24-24
KM 453 GX40NiCrSiNb38-18
KM 454 GX40NiCrSiNb35-25 As Cast Heat resisting alloy steel castings
ASTM-A-351M
KM 455 CF 3 Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 456 CF 3 A Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 458 CF 8 A Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 459 CF 3 M Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 460 CF 3 MA Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 461 CF 8 M Quenched/Solution treated to reqd props. Centrifugals-Hub,Clamping ring,Seperation ring. 1609-S-004,005,006
KM 462 CF 3 MN Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 463 CF 8 C Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 465 CF 10 M Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 466 CH 8 Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
412704185.xls 132 OF 155

KM 467 CH 10 Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 468 CH 20 Quenched/Solution treated to reqd props. Cement Kiln burner tips 1603-B-00035
KM 469 CK 20 Quenched/Solution treated to reqd props. Austenitic steel castings for pressure containing parts.
KM 470 HK 30 As Cast Austenitic steel castings for pressure containing parts.
KM 471 HK 40 As Cast Austenitic steel castings for pressure containing parts.
KM 472 HT 30 As Cast Austenitic steel castings for pressure containing parts.
ASTM-A-297M
KM 473 HF- 19Cr,9Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 474 HH- 25Cr,12Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 475 HI- 28Cr,15Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 476 HK- 25 Cr,20Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 477 HE- 29Cr,9Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 478 HT- 15Cr,35Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 479 HU- 19Cr,39Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 480 HW- 12Cr,60Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 481 HX- 17Cr,66Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 482 HC- 28Cr As Cast / As agreed Heat resistant Steel castings for general application.
KM 483 HD- 28Cr.5Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 484 HL- 29Cr,20Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 485 HN- 20Cr,25Ni As Cast / As agreed Heat resistant Steel castings for general application.
KM 486 HP- 26Cr,35Ni As Cast / As agreed Heat resistant Steel castings for general application.
OTHERS
KM 487 GX-120 Mn 12 Quenched/Solution treated to reqd props. Chain links ( MHE machines ) 1602-B-00067
KM 488 X-165 CrMoV 12 Annealed / Quenched + Tempered Liners,Impact plates,Hammers 1604-B-00001,00002,00004

KM 489 G36Mn5 Annealed/Normalised/Quenched+Tempered Supporting rollers-Cement 1603-B-00009
412704185.xls 133 OF 155

6.5 CAST IRONS

IS 210
KM 501 FG 150 As Cast, any suitable h.t. Pendulum flaps,Kiln burner parts-Cement 1603-B-00016
Soot blower for Boilers,Counter weights,Flywheels & Pulleys Anchor
KM 502 FG 200 As Cast, any suitable h.t. plates, Bearing hsg-Sugar Mills,Handwheels-CSD 1603-B-00016, 1608-B-00100
KM 503 FG 220 As Cast, any suitable h.t. RAL Discharge device,Kiln roller bearing,Thruster,Fresh Air flap 1603-B-00016
KM 504 FG 260 As Cast, any suitable h.t. Centrifugals-Bearing hsg,Bottom ring,Sheaves,Pillow blocks-MHE 1603-B-00016
KM 505 FG 300 As Cast, any suitable h.t. Grey Cast Iron with lamellar / flake graphite 1603-B-00016
EN 1561
412704185.xls 134 OF 155

KM 508 EN-GJL-100 As Cast, Stress relieved,any suitable h.t. Grey Cast Iron with lamellar / flake graphite
ASTM-A-48M
KM 514 150
KM 515 175
KM 516 200
KM 517 225
KM 518 250
KM 519 275
KM 520 300
KM 521 325
KM 522 350
KM 523 375
KM 524 400
6.4.2 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS
IS 1865
KM 525 SG 900/2 As Cast, any suitable h.t. Cast iron with graphite in spheroidal form
KM 528 SG 600/3 As Cast, any suitable h.t. Centrifugals-Housing Lower part.
KM 529 SG 500/7 As Cast, any suitable h.t. Centrifugals-Guide bush,Pressure ring
KM 533 SG 350/22 As Cast, any suitable h.t. Centrifugals-Bearing housing top part.
412704185.xls 135 OF 155

EN 1563
KM 534 EN-GJS-350-22-LT As Cast, Stress relieved,any suitable h.t. Cast iron with graphite in spheroidal form
KM 535 EN-GJS-400-18-LT As Cast, Stress relieved,any suitable h.t. Cast iron with graphite in spheroidal form
KM 536 EN-GJS-400-15 As Cast, Stress relieved,any suitable h.t. Mechanical drive,Swing frame of silo door-Cement
KM 537 EN-GJS-500-7 As Cast, Stress relieved,any suitable h.t. Discharge apparatus - Cement.
KM 538 EN-GJS-600-3 As Cast, Stress relieved,any suitable h.t. Cast iron with graphite in spheroidal form
ASTM-A-536M
KM 541 60-40-18
KM 542 65-45-12
KM 543 80-55-06
KM 544 100-70-03
KM 545 120-90-02
KM 546 60-42-10
KM 547 70-50-05
KM 548 80-60-03
6.4.3 MALLEABLE CAST IRONS
IS 2107
KM 549 WM 410 Malleablising h.t.to achieve microstructure Whiteheart malleable cast iron
KM 550 WM 340 Malleablising h.t.to achieve microstructure Whiteheart malleable cast iron
EN 1562
KM 551 EN-GJMB-350-10 Malleablising h.t.to achieve microstructure Cast iron with graphite in the form of rossettes/temper carbon
412704185.xls 136 OF 155

KM 556 EN-GJMW-350-4 Malleablising h.t.to achieve microstructure Cast iron with graphite in the form of rossettes/temper carbon
ASTM-A-47M
KM 560 22010
ASTM-A-220M
KM 561 280M10
KM 562 310M8
KM 563 310M6
KM 564 340M5
KM 565 410M4
KM 566 480M3
KM 567 550M2
KM 568 620M1

ASTM-A-240M
KM 601 201 Solution Annealed / Quenched High work hardening rate,Low Ni,high Mn equivalent of 301
KM 602 202 Solution Annealed / Quenched Low Ni,high Mn equivalent of 302-used for kitchen equipments
KM 603 301 Solution Annealed / Quenched High work hardening rate,high strength & ductility
KM 604 302 Solution Annealed / Quenched Cement cooler cover strip
KM 605 304 Solution Annealed / Quenched Coal silo,Kiln firing hood,burner,Clinker crusher,Juice trays
KM 606 304 L Solution Annealed / Quenched Pipe for Soot blowers in Boilers
KM 607 304 H Solution Annealed / Quenched Conforms to an average grain size of 7 or coarser
412704185.xls 137 OF 155

KM 608 304 N Solution Annealed / Quenched High N type 304- Increased strength.
KM 609 304 L N Solution Annealed / Quenched Low C & High N type 304- Increased strength & weldability.
KM 610 305 Solution Annealed / Quenched Low work hardening rate-used for spin forming & drawing
KM 611 309 S Solution Annealed / Quenched Throttle flap of TA duct,Kiln burner - Cement
KM 613 309 Cb Solution Annealed / Quenched Cb stabilised grade for restricted carbide pptn during welding
KM 614 309 H Cb Solution Annealed / Quenched Cb stabilised & controlled grain size.
KM 615 310 S Solution Annealed / Quenched Dip tubes in Cement
KM 617 310 Cb Solution Annealed / Quenched Cb stabilised grade for restricted carbide pptn during welding
KM 618 310 H Cb Solution Annealed / Quenched Cb stabilised & controlled grain size.
KM 619 310 Mo L N Solution Annealed / Quenched Low C,High N & presence of Mo-better pitting & creep resistance
KM 620 316 Solution Annealed / Quenched Non-magnetic chutes-MHE,Donnely chute & Pressure chute - Sugar Mills
KM 621 316 L Solution Annealed / Quenched Low C version - for restricted carbide precipitation in welding
KM 623 316 Ti Solution Annealed / Quenched Ti stabilised grade for better resistance to sensitization
KM 624 316 Cb Solution Annealed / Quenched Cb stabilised grade for better resistance to sensitization
KM 625 316 N Solution Annealed / Quenched High N type 316- Increased strength.
KM 626 316 L N Solution Annealed / Quenched Low C & High N type 316- Increased strength & weldability.
KM 627 317 Solution Annealed / Quenched High Mo-Higher corrosion & creep resistance than 316.
KM 628 317 L Solution Annealed / Quenched Low C version - for restricted carbide precipitation in welding
KM 629 317 L N Solution Annealed / Quenched Low C & High N type 317-Increased strength & weldability.
KM 630 321 Solution Annealed / Quenched Polycom housing, Stabilised against sensitization.
KM 632 347 Solution Annealed / Quenched Cb stabilised grade for better resistance to sensitization
KM 633 347 H Solution Annealed / Quenched
KM 634 348 Solution Annealed / Quenched Stabilised with Cb+Ta for better resistance to sensitization
KM 635 348 H Solution Annealed / Quenched
EN 10088
KM 636 X5CrNi18-10 Solution Annealed / Quenched Low C version of 302-better welding properties
412704185.xls 138 OF 155

KM 637 X4CrNi18-12 Solution Annealed / Quenched
KM 638 X8CrNiS18-9 Solution Annealed / Quenched
KM 639 X2CrNi19-11 Solution Annealed / Quenched Extra low C version of 304
KM 640 X2CrNiN18-10 Solution Annealed / Quenched Low C & High N type 304- Increased strength & weldability.
KM 641 X6CrNiTi18-10 Solution Annealed / Quenched Ti stabilised grade for better resistance to sensitization
KM 642 X6CrNiNb18-10 Solution Annealed / Quenched Nb stabilised grade of 304
KM 643 X5CrNiMo17-12-2 Solution Annealed / Quenched Presence of Mo gives better corrosion & creep resistance.
KM 644 X2CrNiMo17-12-2 Solution Annealed / Quenched Extra low C version of 316
KM 645 X2CrNiMoN17-11-2 Solution Annealed / Quenched Low C & High N type 316- Increased strength & weldability.
KM 646 X6CrNiMoTi17-12-2 Solution Annealed / Quenched Ti stabilised grade for better resistance to sensitization
KM 647 X6CrNiMoNb17-12-2 Solution Annealed / Quenched Nb stabilised grade of 316
KM 649 X2CrNiMo18-14-3 Solution Annealed / Quenched
KM 650 X3CrNiMo17-13-3 Solution Annealed / Quenched
KM 651 X2CrNiMo18-15-4 Solution Annealed / Quenched Extra low C version of 317
6.6.2 FERRITIC & MARTENSITIC STAINLESS STEELS
ASTM-A-240M
KM 653 405 Heat treated to achieve reqd mech props Non-hardenable Ferritic SS
KM 654 409 Heat treated to achieve reqd mech props General purpose FSS - Automotive parts
KM 655 429 Heat treated to achieve reqd mech props Nitric acid & Nitrogen-fixation equipment.
KM 656 430 Heat treated to achieve reqd mech props Dishwashers,combustion chambers,recuperators
KM 657 439 Heat treated to achieve reqd mech props
KM 658 444 Heat treated to achieve reqd mech props
412704185.xls 139 OF 155

KM 659 410 Heat treated to achieve reqd mech props Hardenable Martensitic SS - Liners for chutes
KM 660 410 S Heat treated to achieve reqd mech props Low C version of 410
EN 10088
KM 661 X6Cr13 Heat treated to achieve reqd mech props Ferritic Stainless Steel
KM 662 X6CrAl13 Heat treated to achieve reqd mech props Ferritic Stainless Steel
KM 663 X6Cr17 Heat treated to achieve reqd mech props Ferritic Stainless Steel
KM 664 X3CrTi17 Heat treated to achieve reqd mech props Ferritic Stainless Steel
KM 665 X6CrMoS17 Heat treated to achieve reqd mech props
KM 666 X12Cr13 Heat treated to achieve reqd mech props Martensitic Stainless Steel
KM 667 X12CrS13 Heat treated to achieve reqd mech props Martensitic Stainless Steel
KM 672 X50CrMoV15 Heat treated to achieve reqd mech props Martensitic Stainless Steel
KM 673 X14CrMoS17 Heat treated to achieve reqd mech props Martensitic Stainless Steel
KM 674 X17CrNi16-2 Heat treated to achieve reqd mech props Martensitic Stainless Steel
KM 675 X3CrNiMo13-4 Heat treated to achieve reqd mech props Martensitic Stainless Steel
ASTM-A-240M
KM 676 UNS-S31803 Solution Annealed / Quenched } Microstructure of 50% Austenite & 50% Ferrite gives
KM 677 UNS-S32205 Solution Annealed / Quenched } high strength, good pitting and crevice corrosion resistance.
KM 678 UNS-S32304 Solution Annealed / Quenched } Also resistant to Sulphide Stress Corrosion Cracking,
KM 679 329 Solution Annealed / Quenched } corrosion fatigue and Intergranular corrosion.
KM 680 X3CrNiMoN27-5-2 Solution Annealed / Quenched
412704185.xls 140 OF 155

KM 681 X2CrNiMoN22-5-3 Solution Annealed / Quenched Centrifugal basket shell & Hoop rings,top & bottom plates. 1609-B-014
KM 682 X2CrNiN23-4 Solution Annealed / Quenched

EN 10028-2
KM 701 P 235 GH Normalised,Temp control during & after rolling Creep resistant steel plates and strips
412704185.xls 141 OF 155

KM 705 16 Mo 3 Normalised,Temp control during & after rolling Cooler running axle & cover strip,Dip tube - Cement.
KM 706 13 CrMo 4 5 Air / Liquid Quenched Superheater tubes-Boiler,Kiln shell flange,Clinker crusher rotor disc 1603-B-00020
KM 707 10 CrMo 9 10 Air / Liquid Quenched Creep resistant steel plates and strips
KM 708 11 CrMo 9 10 Air / Liquid Quenched Creep resistant steel plates and strips
ASTM-A-515M
KM 709 Grade 60 As rolled,N,N+T< 50mm thk. N for>50mm thk Boiler drums
KM 710 Grade 65 As rolled,N,N+T< 50mm thk. N for>50mm thk C steel plates for intermediate & high temp pressure vessels
ASTM-A-516M
KM 712 Grade 55 As rolled,N,N+T< 40mm thk. N for>40mm thk C steel plates for moderate & low temp pressure vessels
IS 2002
KM 716 Grade 1 Plates above 12mm - Normalised Low tensile steel plates for welding .
KM 717 Grade 2 Plates above 12mm - Normalised Medium tensile-Boiler drums, Vibrating Screens - MHE 1603-B-00020
KM 718 Grade 3 Plates above 12mm - Normalised High tensile steel plates for welding under controlled conditions.
BS 1501
KM 719 141 - Gr 360

KM 720 154 - Gr 360
KM 721 154 - Gr 400
KM 722 154 - Gr 430
412704185.xls 142 OF 155

KM 723 151 - Gr 360
KM 724 151 - Gr 400
KM 725 151 - Gr 430
KM 726 161 - Gr 360
KM 727 161 - Gr 400
KM 728 161 - Gr 430
KM 729 164 - Gr 360
KM 730 164 - Gr 400
KM 731 223 - Gr 460
KM 732 223 - Gr 490
KM 733 224 - Gr 400
KM 734 224 - Gr 430
KM 735 224 - Gr 460
KM 736 224 - Gr 490 Plates for Boiler drums 1608-B-00093
KM 737 225 - Gr 460
KM 738 225 - Gr 490
BS 3059-1
KM 739 HFS 320
KM 740 CFS 320
412704185.xls 143 OF 155

KM 741 ERW 320 Electrical resistance welded Boiler Tubes 1608-B-00099
KM 742 CEW 320
BS 3059-2
KM 743 360
KM 744 440
KM 745 243
KM 746 620-460
KM 747 622-490
KM 748 629-470
KM 749 629-590
KM 750 762
KM 751 304S51
KM 752 316S51
KM 753 316S52
KM 754 321S51 (1010)
KM 755 321S51 (1105)
KM 756 347S51
KM 757 215S15
BS 3602-1
KM 758 360 - Seamless Hot finished seamless tubes for Boiler Headers. 1608-B-00094
KM 759 360 - Welded
KM 760 430 - Seamless
KM 761 430 - Welded
KM 762 500Nb-Seamless
BS 3602-2
KM 763 430
KM 764 490
ASTM-A-213M
412704185.xls 144 OF 155

KM 765 T2
KM 766 T5
KM 767 T 5b
KM 768 T 5c
KM 769 T9
KM 770 T 11 Boiler Superheater Tubes
KM 771 T 12
KM 772 T 17
KM 773 T 21
KM 774 T 22
KM 775 T 91
KM 776 T 92
KM 777 18 Cr-2 Mo
KM 778 TP 304
KM 779 TP 304 H
KM 780 TP 304 N
KM 781 TP 304 LN
KM 782 TP 304 L
KM 783 TP 309 Cb
KM 784 TP 309 HCb
KM 785 TP 309 S
KM 786 TP 310 HCbN
KM 787 TP 316
KM 788 TP 317
KM 789 TP 321
KM 790 TP 347
KM 791 TP 347 HFG
KM 792 TP 348
ASTM-A-106
KM 793 Grade A
412704185.xls 145 OF 155

KM 794 Grade B Boiler Headers and Piping
KM 795 Grade C

KM 796 St 35.8
KM 797 St 45.8
KM 798 17 Mn 4
KM 799 19 Mn 5
KM 800 15 Mo 3
KM 801 13 CrMo 4 4
KM 802 10 CrMo 9 10
KM 803 14 MoV 6 3
KM 804 X 20 CrMoV12 1
KM 805 15 NiCuMoNb 5
6.8 SPRING STEELS
412704185.xls 146 OF 155

IS 2507 Cold rolled spring steel
KM 806 Grade 1 - 45 C 8 Annealed / Quenched + Tempered
KM 807 Grade 2 - 55 C 6 Annealed / Quenched + Tempered Brake band assembly in Centrifugal machine. 1609-S-003
KM 810 Grade 5 - 75 C 6 Annealed / Quenched + Tempered Spring plates of RAL - Cement
KM 814 Grade 9 - 55 Si 7 Annealed / Quenched + Tempered
KM 815 Grade 10 - 50 Cr 4 Annealed / Quenched + Tempered
KM 816 Grade 11-50Cr4V2 Annealed / Quenched + Tempered
DIN 17221 Hot rolled spring steels

KM 817 38 Si 7 Softened, Spheroidised, Shearable
KM 818 54 Si Cr 6 Softened, Spheroidised, Shearable
KM 819 60 Si Cr 7 Softened, Spheroidised, Shearable
KM 820 55 Cr 3 Softened, Spheroidised, Shearable
KM 821 50 Cr V 4 Softened, Spheroidised, Shearable
KM 822 51 Cr Mo V 4 Softened, Spheroidised, Shearable
DIN 17222 Cold rolled spring steel

KM 823 C 55 Softened / Hardened + Tempered
KM 827 Ck55 Softened / Hardened + Tempered
KM 828 Ck 60 Softened / Hardened + Tempered
412704185.xls 147 OF 155

KM 833 55 Si 7 Softened / Hardened + Tempered
KM 834 71 Si 7 Softened / Hardened + Tempered
KM 835 67 Si Cr 5 Softened / Hardened + Tempered
KM 836 50 Cr V 4 Softened / Hardened + Tempered
BS 970-2 Hot formed spring steel

KM 837 251 A 58 Annealed / Quenched + Tempered
KM 848 251 H 60 Annealed / Quenched + Tempered Spring steels with hardenability requirements.
412704185.xls 148 OF 155

EN 10084
KM 901 C10E
KM 902 C15E
KM 903 C16E
KM 904 17Cr3
KM 905 28Cr4
KM 906 16MnCr5 Case hardened bushes in CSD
KM 907 20MnCr5
KM 908 18CrMo4
KM 909 22CrMoS3-5
KM 910 20MoCr3
KM 911 20MoCr4
KM 912 16NiCr4
KM 913 18NiCr5-4
KM 914 17CrNi6-6
KM 915 15NiCr13
KM 916 20NiCrMo2-2
KM 917 17NiCrMo6-4
KM 918 20NiCrMoS6-4
KM 919 18CrNiMo7-6
412704185.xls 149 OF 155

DIN 1705
KM 1001 G - CuSn 12 AS CAST Explosion flap of coal silo 1602-B-00022
KM 1002 GZ - CuSn 12 AS CAST 1602-B-00022
KM 1003 GC - CuSn 12 AS CAST 1602-B-00022
KM 1004 G - CuSn 12 Ni AS CAST 1602-B-00022
KM 1005 GZ - CuSn 12 Ni AS CAST 1602-B-00022
KM 1006 GC - CuSn 12 Ni AS CAST 1602-B-00022
KM 1007 G - CuSn 12 Pb AS CAST Bushes - MHE 1602-B-00022
KM 1008 GZ - CuSn 12 Pb AS CAST 1602-B-00022
KM 1009 GC - CuSn 12 Pb AS CAST 1602-B-00022
KM 1010 G - CuSn 10 AS CAST Bushes - MHE, Centrifugal baskets - Cup 1602-B-00022
KM 1011 G - CuSn 10 Zn AS CAST Swing frame & Fix frame of cooler 1602-B-00022
KM 1012 G - CuSn 7 ZnPb AS CAST Bushes and bearings - MHE 1602-B-00022
KM 1013 GZ - CuSn 7 ZnPb AS CAST 1602-B-00022
KM 1014 GC - CuSn 17 ZnPb AS CAST 1602-B-00022
KM 1015 G - CuSn 6 ZnNi AS CAST 1602-B-00022
KM 1016 G - CuSn 5 ZnPb AS CAST 1602-B-00022
KM 1017 G - CuSn 2 ZnPb AS CAST 1602-B-00022
DIN 1709
KM 1018 G - CuZn 15 AS CAST
KM 1019 G - CuZn 33 Pb AS CAST
KM 1020 G - CuZn 37 Pb AS CAST
KM 1021 GD - CuZn 37 Pb AS CAST
KM 1022 GK - CuZn 37 Pb AS CAST
KM 1023 G - CuZn 38 Al AS CAST
KM 1024 GK - CuZn 38 Al AS CAST
KM 1025 G - CuZn 40 Fe AS CAST
412704185.xls 150 OF 155

KM 1026 GZ - CuZn 40 Fe AS CAST
KM 1027 GK - CuZn 37 Al 1 AS CAST
KM 1028 G - CuZn 35 Al 1 AS CAST
KM 1029 GZ - CuZn 35 Al 1 AS CAST
KM 1032 GZ - CuZn 34 Al 2 AS CAST Bushes - MHE
KM 1035 GZ - CuZn 25 Al 5 AS CAST
KM 1037 G - CuZn 15 Si 4 AS CAST
KM 1038 GD - CuZn 15 Si 4 AS CAST
KM 1039 GK - CuZn 15 Si 4 AS CAST
DIN 1714
KM 1040 G - CuAl 10 Fe AS CAST
KM 1041 GK - CuAl 10 Fe AS CAST
KM 1042 GZ - CuAl 10 Fe AS CAST
KM 1043 G - CuAl 9 Ni AS CAST
KM 1044 GK - CuAl 9 Ni AS CAST
KM 1045 GZ - CuAl 9 Ni AS CAST
KM 1048 GZ - CuAl 10 Ni AS CAST Bushes - MHE
KM 1049 GC - CuAl 10 Ni AS CAST
KM 1052 GZ - CuAl 11 Ni AS CAST
KM 1053 G - CuAl 8 Mn AS CAST
KM 1054 GK - CuAl 8 Mn AS CAST
412704185.xls 151 OF 155

IS 318
KM 1055 LTB 1 AS CAST
KM 1056 LTB 2 AS CAST Discharge apparatus-Cement,Bushes & Bearing liners-Sugar Mills
IS 305
KM 1061 GRADE AB 1
KM 1062 GRADE AB 2
IS 306
KM 1063 Ingots
KM 1064 Castings
IS 25
KM 1065 GRADE 90 AS CAST
KM 1072 GRADE 6 AS CAST Drive bearing of Kiln
412704185.xls 152 OF 155

BS 1400
KM 1075 PB4
KM 1076 LPB1
KM 1077 LB2
KM 1078 LB4
KM 1079 LG1
KM 1080 LG2 Silo cone agitator - Cement
KM 1081 SCB1
KM 1082 SCB3
KM 1083 SCB6
KM 1084 DCB1
KM 1085 DCB3
KM 1086 PCB1
KM 1087 HCC1
KM 1088 CC1-TF
KM 1089 PB1
KM 1090 PB2
KM 1091 CT1
KM 1092 LG4
KM 1093 AB1
KM 1094 AB2
KM 1095 CMA1
KM 1096 HTB1
KM 1097 HTB3
KM 1098 LB1
KM 1099 LB5
KM 1100 G1
KM 1101 G3
KM 1102 G3-TF
KM 1103 SCB4
KM 1104 CT2
412704185.xls 153 OF 155

KM 1105 AB3
KM 1106 CN1
KM 1107 CN2
412704185.xls 154 OF 155

SS PLATE 22A EN10029 EN10088 1.4462

Chemical Composition of Materials

Uploaded by

Copyright:

Available Formats

Chemical Composition of Materials

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chemical Composition of Materials

Uploaded by

Copyright:

Available Formats

KRUPP INDUSTRIES INDIA LTD.

Design & MATERIAL REFERENCE MANUAL G.L. No.:1600-8

Sr. No. DESCRIPTION

1 Scope and purpose

1 SCOPE & PURPOSE :

1.1 This manual covers the following types of materials:

Low Carbon Structural steels

List of standards covered in the Materials Manual.

ASTM-A-27M - 95 DIN 1681 - 85 IS 25 - 79

4.1 LOW CARBON STRUCTURAL STEELS

IS 2062 Steel for General Structural Purposes

IS 1079 Hot rolled carbon steel sheets & strips

IS 513 Cold rolled low carbon steel sheets & strips

EN 10025 Hot Rolled Products of non alloyed Structural Steels

ASTM-A-36M Structural Carbon Steel

ASTM-A-283M Low and Intermediate tensile strength Carbon steel plates

ASTM-A-299M Carbon steel plates for Pressure Vessels

ASTM-A-366M Cold rolled ,Commercial quality Carbon steel sheets

ASTM-A-387M Chromium - Molybdenum alloy steel Pressure vessel plates.

ASTM-A-573M Structural Carbon Steel Plates with improved toughness

4.1.1 WELDABLE, FINE GRAINED STRUCTURAL STEELS

4.2 ROLLED / FORGED STEELS

IS 1570-2 Wrought Carbon Steel Schedules

BS 970-3 Wrought Steels for Mechanical & Allied Engineering Purposes

EN 10083 Quenched & Tempered Unalloyed Quality Steels

4.2.2 LOW ALLOY STEELS

EN 10083-1 Quenched & Tempered Special Steels

ASTM-A-108 Cold Finished , Standard quality Carbon Steel bars

ASTM-A-322 Standard grades of Alloy Steel bars

4.3 CARBON STEEL CASTINGS

IS 2707 Carbon Steel Castings for Surface Hardening

ASTM-A-27M Carbon Steel Castings for General Applications

ASTM-A-128M Austenitic Manganese Steel Castings

ASTM-A-148M High Strength Steel Castings for Structural Purposes

4.4 ALLOY STEEL CASTINGS

IS 4522 Heat Resistant Alloy Steel & Nickel base Castings

DIN 17465 Heat Resistant Steel Castings

SEW 390 Austenitic Manganese steel

DIN 17350 Tool Steel

SEW 835 Steel Castings for Flame & Induction Hardening

4.5 CAST IRONS Microstructure

EN 1561 GREY CAST IRONS Graphite flakes in matrix of

ASTM-A-48M GREY CAST IRONS

4.5.2 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS Graphite nodules in matrix of

EN 1563 NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

ASTM-A-536M NODULAR / SPHEROIDAL GRAPHITE CAST IRONS

4.5.3 MALLEABLE CAST IRONS Microstructure

IS 2107 MALLEABLE CAST IRONS

EN 1562 MALLEABLE CAST IRONS

ASTM-A-47M MALLEABLE CAST IRONS

ASTM-A-220M MALLEABLE CAST IRONS

4.6 STAINLESS STEELS

DIN 17440 EN 10088

4.6.3 DUPLEX STAINLESS STEELS

4.7 HIGH TEMPERATURE STEELS

KM 709 ASTM-A-515M Grade 60 IS 2002 Grade 2 DIN 17155 - H II EN 10028-2 P265GH

KM 712 ASTM-A-516M Grade 55 IS 2002 Grade 1 DIN 17155 - H I EN 10028-2 P235GH

KM 713 ASTM-A-516M Grade 60 IS 2002 Grade 2 DIN 17155 - H II EN 10028-2 P265GH

4.7.2 TUBES AND PIPES