Getting Started Abaqus Appendix C

Appendix C: Abaqus/CAE: AN ADVANCED TUTORIAL
Appendix C: Using Additional Techniques to Create and

Analyze a Model in Abaqus/CAE
Appendix B, “Creating and Analyzing a Simple Model in Abaqus/CAE,” explains how to create and analyze
a very simple model composed of only one part. In this advanced tutorial for the experienced Abaqus user
you will create and analyze a more complex model. The model is more complex on two levels:
• It consists of three different parts and three different part instances rather than just one. This tutorial
illustrates how you position instances of these parts to create the assembly and how you deÞne contact
between surfaces of the assembly.
• It includes parts that you will draw using advanced sketching techniques. You will learn how sketches,
datum geometry, and partitions combine to deÞne the features that make up individual parts. You will
also learn how you can modify a part by editing a feature and how modiÞed parts are regenerated.
As in Appendix B, “Creating and Analyzing a Simple Model in Abaqus/CAE,” you will apply section
properties, loads, and boundary conditions to the model; you will also mesh the model, conÞgure the analysis,
and run the analysis job. At the end of the tutorial you will view your analysis results. The entire tutorial takes
approximately three hours to complete.
This tutorial assumes that you are familiar with the techniques described in Appendix B, “Creating and
Analyzing a Simple Model in Abaqus/CAE,” including the following:
• Using the view manipulation tools to rotate and zoom an object in the viewport.
• Following the prompts in the prompt area.
• Using the mouse to select menu items, toolbox items, and items within the viewport.
C.1 Overview
During the tutorial you will create an assembly composed of a hinge held together by a pin. The
assembled part instances and the Þnal mesh are illustrated in Figure C–1.
The tutorial consists of the following sections:
• “Creating the Þrst hinge piece,” Section C.2
• “Assigning section properties to the hinge part,” Section C.3
• “Creating and modifying a second hinge piece,” Section C.4
• “Creating the pin,” Section C.5
• “Assembling the model,” Section C.6
• “DeÞning analysis steps,” Section C.7
• “Creating surfaces to use in contact interactions,” Section C.8
• “DeÞning contact between regions of the model,” Section C.9
• “Applying boundary conditions and loads to the assembly,” Section C.10
C–1
Figure C–1 Model used in the hinge tutorial.
• “Meshing the assembly,” Section C.11

• “Creating and submitting a job,” Section C.12
• “Viewing the results of your analysis,” Section C.13
C.2 Creating the first hinge piece

To start the tutorial, you create the Þrst part—half of the hinge. Abaqus/CAE models are composed of
features; you create a part by combining features. This portion of the hinge is composed of the following
features:
• A cube—the base feature, since it is the Þrst feature of the part.
• A ßange that extends from the cube. The ßange also includes a large-diameter hole through which
the pin is inserted.
• A small lubrication hole in one corner of the ßange.
Creating the cube

To create the cube (the base feature), you create a solid, three-dimensional, extruded part and name it.
You then sketch its proÞle (0.04 m × 0.04 m) and extrude the proÞle over a speciÞed distance (0.04 m)
to produce the base feature of the Þrst half of the hinge. The desired cube is shown in Figure C–2.
Note: The default render style used throughout Abaqus/CAE is Shaded. For clarity, many of the Þgures
in this tutorial use the wireframe or hidden line render styles. For more information, see “Choosing a
render style,” Section 58.2 of the Abaqus/CAE User’s Manual.
C–2
3 1
Figure C–2 The base feature (a cube) is created Þrst.
To create the cube:

1. Start Abaqus/CAE, and create a new model database. Resize your windows so that you can follow
the tutorial and see the Abaqus/CAE main window.
Abaqus/CAE enters the Part module and displays the Model Tree in the left side of the main window.
2. In the Model Tree, double-click the Parts container to create a new part.
The Create Part dialog box appears.
The text in the prompt area asks you to Þll out the Create Part dialog. Abaqus/CAE always displays
prompts in the prompt area to guide you through a procedure.
3. Name the part Hinge-hole. Accept the following default settings:
• A three-dimensional, deformable body
• A solid extrusion base feature
4. In the Approximate size text Þeld, type 0.2. You will be modeling the hinge using meters for
the unit of length, and its overall length is 0.14 meters; therefore, 0.2 meters is a sufÞciently large
approximate size for the part. Click Continue to create the part.
The Sketcher starts and displays the toolbox between the canvas and the Model Tree. Abaqus/CAE
uses the approximate size of the part to compute the default sheet size—0.2 meters in this example.
In addition, in this example the Sketcher draws 40 grid lines on the sheet, and the distance between
each grid line is 0.005 meters. (You probably see fewer than 40 grid lines because the sheet extends
beyond your viewport.)
5. From the Sketcher toolbox, select the rectangle tool .

6. Sketch an arbitrary rectangle, and click mouse button 2 in the viewport to exit the rectangle tool.
7. Dimension the top and left edges so that each is 0.04 m long.
C–3
Important: To complete this tutorial successfully, it is important that you use the
dimensions stated and do not deviate from the example; otherwise, you will Þnd it
difÞcult to assemble the model.
8. Click mouse button 2 to exit the Sketcher.
Tip: Clicking mouse button 2 in the viewport has the same effect as clicking the default
button in the prompt area—Done in this instance.
Abaqus/CAE displays the Edit Base Extrusion dialog box.
9. In the dialog box, type a Depth of 0.04 and press [Enter].
Abaqus/CAE exits the Sketcher and displays the base feature, a cube, as shown in Figure C–2. The
triad in the lower-left corner of the viewport indicates the orientation of the X-, Y-, and Z-axes.
You can turn off this triad by selecting Viewport Viewport Annotation Options from the main
menu bar and toggling off the Show triad option. (The triad is sometimes turned off for clarity in
the Þgures in this tutorial.)
Note: By default, Abaqus/CAE uses the alphabetical option, x-y-z, for labeling the view
orientation triad. In general, this manual adopts the numerical option, 1-2-3, to permit direct
correspondence with degree of freedom and output labeling. For more information on labeling of
axes, see “Customizing the view triad,” Section 5.4 of the Abaqus/CAE User’s Manual.
Adding the flange to the base feature

You will now add a solid feature—the ßange—to the base feature. You select one face of the cube to
deÞne the sketch plane and extrude the sketched proÞle through half the depth of the cube. The cube and
ßange are shown in Figure C–3.
2
3 1
Figure C–3 The ßange is added to the base feature.
C–4
To add the flange to the base feature:

1. From the main menu bar, select Shape Solid Extrude.
2. Select the face at the front of the cube to deÞne the sketching plane, as shown in Figure C–4.
Select this edge
Figure C–4 Select the gridded face to deÞne the sketching plane.
Select the indicated edge to position the part correctly in the Sketcher.
When you stop moving the cursor during a selection procedure, Abaqus/CAE highlights the edges
of the entity that it would select at the current cursor position. This highlighting behavior is called
“preselection.”
Note: Two forms of preselection are available in Abaqus/CAE: one for object selection from the
viewport and the other for selection from the Sketcher. For more information, see “Highlighting
objects prior to selection,” Section 6.3.4 of the Abaqus/CAE User’s Manual, and “Turning
preselection on or off,” Section 19.9.3 of the Abaqus/CAE User’s Manual, respectively.
3. Select an edge that will appear vertical and on the right side of the sketch, as shown in Figure C–4.
Again, Abaqus/CAE uses preselection to aid you in selecting the desired edge.
The Sketcher starts and displays the outline of the base feature as reference geometry. Abaqus/CAE
magniÞes the view to Þt the sketch plane; the sheet size and grid spacing are also recalculated based
on the size of the sketch plane. To change the sheet size and grid spacing back to their original
settings and disable their automatic recalculation for the current session, use the options tool ,
located in the Sketcher toolbox. On the General tabbed page, toggle off Auto next to the sheet size
text Þeld and set the value to 0.2; toggle off Auto next to the grid spacing text Þeld and set the
value to 0.005.
Tip: To retain the original sheet size and grid spacing for all sketches in a part, you can
select the options tool while sketching the base feature—the cube—and toggle off both
Auto settings.
C–5
The sketch of the ßange that you will create is illustrated in Figure C–5. To duplicate the view in
the Þgure, use the options tool again to double the grid spacing.
Figure C–5 Use the Sketcher to create the ßange proÞle.
4. Zoom out to view the area where you will sketch the ßange:
a. From the View Manipulation toolbar, select the magnify tool .

b. Position the cursor near the center of the viewport.
c. Click mouse button 1 and drag to the left until the cube occupies approximately half of the
visible Sketcher space.
Reducing the view is necessary because the ßange is created beyond the edges of the selected sketch
plane.
5. As before, the approximate shape of the new feature will be sketched Þrst. From the Sketcher
toolbox, select the connected lines tool .

6. Sketch the rectangular portion of the ßange by drawing three lines as follows:
a. Starting at any point to the right of the cube, connect the line to the top-right corner of the cube.
b. Continue the next line to the bottom-right corner of the cube. This line is automatically
assigned a vertical constraint.
c. The Þnal line extends from the bottom-right corner of the cube to any point to the right of the
cube.
Tip: If you make a mistake while sketching, use the Sketcher undo or delete
tools to correct your error.
7. Click mouse button 2 in the viewport to exit the connected lines tool.
C–6
8. ReÞne the sketch by deÞning the following constraints and dimension:
a. Use the constraints tool to constrain the top and bottom lines of the sketch so that each is
horizontal.
b. Assign an equal length constraint to these two lines (use [Shift]+Click to select both lines).
c. Dimension either line so that it is 0.02 m long.
The sketch appears as shown in Figure C–6.
20.E-03
20.E
H
Figure C–6 Draw the rectangular portion of the ßange.
9. Close the proÞle by adding a semicircular arc using the 3-points circle tool .
a. Select the two vertices at the open end of the rectangle as the endpoints of the arc, starting with
the top one. Select any point to the right of the sketch as a point that lies on the arc.
b. DeÞne tangent constraints between the ends of the arc and the horizontal lines to reÞne the
sketch.
10. Click mouse button 2 in the viewport to exit the 3-points circle tool.
The resulting arc is shown in Figure C–7.
11. From the Sketcher toolbox, select the center-perimeter circle tool to sketch the ßange hole.
a. Place the center of the circle to coincide approximately with the center of the arc created
previously. The perimeter point should be placed to the right of the center point. Apply a
concentric constraint between the two circular regions.
b. Use the dimension tool to change the value of the radius to 0.01 m.
C–7
20.E-03
20.E
H
Figure C–7 Add the curved portion of the ßange.
c. Dimension the vertical distance between the center of the circle and the perimeter point. Edit
this dimension so that the distance is 0. (If the distance is already 0, you cannot add a vertical
dimension.) This will adjust the location of the perimeter point so that it is on the same
horizontal plane as the center point.
Note: When you mesh a part, Abaqus/CAE places nodes wherever vertices appear along an
edge; therefore, the location of the vertex on the circumference of the circle inßuences the Þnal
mesh. Placing it on the same horizontal plane as the center point results in a high-quality mesh.
12. The Þnal sketch is shown in Figure C–8.
Abaqus/CAE displays the part in an isometric view showing the base extrusion, your sketched
proÞle, and an arrow indicating the extrusion direction. The default extrusion direction for a solid
is always out of the solid. Abaqus/CAE also displays the Edit Extrusion dialog box.
Tip: Use the auto-Þt view manipulation tool to Þt the sketched ßange proÞle and
the base extrusion in the viewport.
14. In the Edit Extrusion dialog box:
a. Accept the default Type selection of Blind to indicate that you will provide the depth of the
extrusion.
b. In the Depth Þeld, type an extrusion depth of 0.02.
c. Click Flip to reverse the extrusion direction, as shown in Figure C–9.
C–8
20.E-03
20.E
H
V V 0.
10.E-03
10.E
Figure C–8 Final sketch.
2
3 1
Figure C–9 Completed ßange sketch showing the extrusion direction.
d. Toggle on Keep internal boundaries. When you toggle this option on, Abaqus/CAE
maintains the face that is generated between the extruded solid feature and the existing part.
As a result, the extruded ßange is maintained as a second cell and is not merged with the
cube. (When you mesh the model at the end of the tutorial, the internal boundary allows you
to mesh the ßange without having to Þrst partition the cell and ßange into separate cells.)
e. Click OK to create the solid extrusion.
C–9
Abaqus/CAE displays the part composed of the cube and the ßange. Use the auto-Þt view
manipulation tool again to resize the part to Þt in the viewport.
Modifying a feature
Each part is deÞned by a set of features, and each feature in turn is deÞned by a set of parameters. For
example, the base feature (the cube) and the second feature (the ßange) are both deÞned by a sketch and
an extrusion depth. You modify a part by modifying the parameters that deÞne its features. For the hinge
example you will change the radius of the hole in the sketch of the ßange from 0.01 m to 0.012 m.
To modify a feature:
1. In the Model Tree, expand the Hinge-hole item underneath the Parts container. Then expand the
Features container that appears.
A list showing each feature’s Name appears. In this example you have created two solid extrusion
features: the base feature (the cube), Solid extrude-1, and the ßange, Solid extrude-2.
2. Click mouse button 3 on Solid extrude-2 (the ßange) in this list.
Abaqus/CAE highlights the selected feature in the viewport.
3. From the menu that appears, select Edit.
Abaqus/CAE displays the feature editor. For an extruded solid you can change the extrusion depth,
the twist or draft (if speciÞed when the feature was created), and the proÞle sketch.
4. From the feature editor, click Edit Section Sketch.
Abaqus/CAE displays the sketch of the second feature, and the feature editor disappears.
5. From the edit tools in the Sketcher toolbox, select the edit dimension value tool .
6. Select the radial dimension of the circle (0.010).
7. In the Edit Dimension dialog box, type a new radius of 0.012 and click OK.
Abaqus/CAE closes the dialog box and changes the radius of the circle in the sketch only.
8. Click mouse button 2 to exit the edit dimension value tool. Click mouse button 2 again to exit the
Sketcher.
Abaqus/CAE again displays the feature editor.
9. Click OK to regenerate the ßange with the modiÞed radius and to exit the feature editor.
The ßange hole is enlarged to the new radius dimension.
Note: In some circumstances regenerating a feature causes dependent features to fail. In such a
case Abaqus/CAE asks if you want to save your changes and suppress the features that failed to
regenerate, or if you want to revert to the unmodiÞed feature and lose your changes.
C–10
Creating the sketch plane

The ßange includes a small hole used for lubrication, as shown in Figure C–10.
Figure C–10 Isometric shaded view of the hinge with the lubrication hole.
Creating the hole in the desired location requires an appropriate datum plane on which to sketch the
proÞle of the extruded cut, as shown in Figure C–11.
Datum plane
Datum axis
Datum point
45°
Figure C–11 Two-dimensional view of the datum plane’s position with respect to the hinge piece.
You sketch a circle on the datum plane, which is tangent to the ßange, and Abaqus/CAE extrudes the
circle normal to the datum plane and normal to the ßange to create the lubrication hole.
C–11
There are three operations involved in creating the datum plane:

• Creating a datum point on the circumference of the ßange.
• Creating a datum axis running between two datum points.
• Creating a datum plane through the datum point on the circumference and normal to the datum axis.
To create the sketch plane:

1. From the main menu bar, select Tools Datum.
Abaqus/CAE displays the Create Datum dialog box.
2. Create a datum point along the curved edge of the ßange through which the datum plane will pass.
From the Create Datum dialog box, choose the Point datum type.
3. From the list of methods, click Enter parameter.
4. Select the curved edge, as shown in Figure C–12. Note the direction of the arrow indicating an
increasing edge parameter from 0.0 to 1.0. You cannot change the direction of this arrow.
Select
this edge
3 1
Figure C–12 Create a datum point along the curved edge of the ßange.
5. In the text box in the prompt area, enter a normalized edge parameter and press [Enter]. If the arrow
direction is the same as in Figure C–12, enter 0.75 as the normalized edge parameter; if the arrow
points in the opposite direction, enter 0.25 as the normalized edge parameter.
Abaqus/CAE creates a datum point along the selected edge.
6. Create a datum axis that will deÞne the normal to the datum plane. From the Create Datum dialog
box, choose the Axis datum type. Click the 2 points method.
Abaqus/CAE highlights the points that can be used to create the datum axis.
C–12
7. Select the point at the center of the hole (created when you sketched the hole’s proÞle) and the datum
point on the curved edge.
Abaqus/CAE displays a datum axis passing through the two points, as shown in Figure C–13.
2
3 1
Figure C–13 Create a datum axis deÞned by two datum points.
8. The Þnal step is to create the datum plane normal to the datum axis. From the Create Datum dialog
box, choose the Plane datum type. Click the Point and normal method.
9. Select the datum point on the curved edge as the point through which the datum plane will pass.
10. Select the datum axis as the edge that will be normal to the datum plane.
Abaqus/CAE creates the datum plane, as shown in Figure C–14.
Sketching the lubrication hole

The next operation creates the lubrication hole on the ßange by extruding a circle from the datum plane
that you just created. First, you need to create a datum point on the ßange that indicates the center of the
hole, as illustrated in Figure C–15.
To create the datum point at the center of the lubrication hole:

1. If it is not open already, display the Create Datum dialog box by selecting Tools Datum from
the main menu bar.
2. Create a datum point along the second curved edge of the ßange. From the Create Datum dialog
box, choose the Point datum type.
C–13
2
3 1
Figure C–14 Create a datum plane normal to the datum axis.
datum point indicates

the center of the
lubrication hole
Figure C–15 A datum point indicates the center of the lubrication hole.
3. From the list of methods, click Enter parameter.

4. Select the second curved edge of the ßange, as shown in Figure C–16.
C–14
Select
this edge
3 1
Figure C–16 Select the second edge.
5. Note the direction of the arrow indicating an increasing edge parameter from 0.0 to 1.0. Enter a
normalized edge parameter of 0.75 (or 0.25 if the sense of the arrow is opposite that shown in
Figure C–16), and press [Enter].
Abaqus/CAE creates a datum point along the selected edge.
6. From the list of methods in the Create Datum dialog box, select Midway between 2 points.
7. Select the datum point along the Þrst curved edge.
8. Select the datum point along the second curved edge.
Abaqus/CAE creates a datum point halfway across the ßange.
9. Close the Create Datum dialog box.
This exercise illustrates how you can use feature-based modeling to capture your design intent. The
datum point is a feature that Abaqus/CAE deÞnes to be midway between the datum points along
the edges of the ßange. As a result, if you change the thickness of the ßange, the lubrication hole
remains in the center.
To sketch the lubrication hole:

1. From the main menu bar, select Shape Cut Extrude.
2. Click the boundary of the datum plane to select it as the plane on which to sketch.
3. Select the top rear edge of the cube as the edge that will appear vertical and on the right side of the
sketch, as shown in Figure C–17.
C–15
Select this
edge
Figure C–17 Select the indicated edge to position the part correctly in the Sketcher grid.
The Sketcher starts with the vertices, datums, and edges of the part projected onto the sketch plane
as reference geometry.
Tip: If you are unsure of the relative orientation of the sketch plane and the part, use the
view manipulation tools to rotate and pan them. Use the reset view tool to restore
the original view.
4. From the Sketcher toolbox, select the circle tool .

5. Select the datum point on the center of the ßange to indicate the center of the circle.
6. Select any other point, and click mouse button 1.
7. Dimension the radius of the hole. The radius of the circle should be changed to 0.003 m.
8. Dimension the vertical distance between the circle’s center and perimeter points. Set this distance
to zero. As noted earlier, this will improve the quality of the mesh.
9. Exit the Sketcher.
Abaqus/CAE displays the hinge in an isometric view showing the base part and ßange, your
sketched hole proÞle, and an arrow indicating the direction for the extruded cut. Abaqus/CAE also
displays the Edit Cut Extrusion dialog box.
10. From the Type menu in the Edit Cut Extrusion dialog box, select Up to Face and click OK.
11. Select the cylindrical inner surface of the hole in the part to indicate the face to which to extrude,
as illustrated in Figure C–18. (Because you can select at most only one face, Abaqus/CAE does not
ask you to indicate that you have Þnished selecting.)
Abaqus/CAE extrudes the sketch from the datum plane to the hole in the ßange.
C–16
Select
this surface
Figure C–18 Select the face to which to extrude.
12. From the Render Style toolbar, select the shaded display tool if necessary, and use the rotation
tool to see how the part and its features are oriented, as shown in Figure C–19. (For clarity, the
datum geometry has been removed from the view in Figure C–19 by selecting View Part Display
Options Datum.)
Figure C–19 Isometric view of the Þrst hinge.
C–17
Tip: After you rotate the part, use the cycle views tool to step through the previous
views (up to a maximum of eight) and to restore the original view.
13. Now that you have created the Þrst part of your model, it is a good idea to save your model in a
model database:
a. From the main menu bar, select File Save. The Save Model Database As dialog box
appears.
b. Type a name for the new model database in the File Name Þeld, and click OK. You do not
need to include the Þle extension; Abaqus/CAE appends .cae automatically to the Þle name.
Abaqus/CAE stores the model database in a new Þle and returns to the Part module. The name
of your model database appears in the main window title bar.
If you Þnd you need to interrupt this tutorial, you can save the model database at any time and exit
Abaqus/CAE. You can then start a new Abaqus/CAE session and open the saved model database by
selecting Open Database from the Start Session dialog box. The model database will contain
any parts, materials, loads, etc. that you created, and you will be able to continue the tutorial.
C.3 Assigning section properties to the hinge part

The process of assigning section properties to a part is divided into three tasks:
• Creating a material.
• Creating a section that includes a reference to the material.
• Assigning the section to the part or to a region of the part.
Creating a material
You will create a material named Steel that has a Young’s modulus of 209 GPa and a Poisson’s ratio
of 0.3.
To define the material:

1. In the Model Tree, double-click the Materials container to create a new material.
The Edit Material dialog box appears.
2. Name the material Steel.
3. From the editor’s menu bar, select Mechanical Elasticity Elastic.
Abaqus/CAE displays the Elastic data form.
4. In the respective Þelds in the Elastic data form, type a value of 209.E9 for Young’s modulus and
a value of 0.3 for Poisson’s ratio.
5. Click OK to exit the material editor.
C–18
Defining a section
Next, you will create a section that includes a reference to the material Steel.
To define the section:

1. In the Model Tree, double-click the Sections container to create a section.
The Create Section dialog box appears.
2. In the Create Section dialog box:
a. Name the section SolidSection.

b. In the Category list, accept Solid as the default selection.
c. In the Type list, accept Homogeneous as the default selection, and click Continue.
The section editor appears.
3. In the editor, accept Steel as the material selection and click OK.
If you had deÞned other materials, you could click the arrow next to the Material text box to see a
list of available materials and to select the material of your choice.
Assigning the section

You will now assign the section SolidSection to the hinge part.
To assign the section to the hinge part:

1. In the Model Tree, expand the Hinge-hole item underneath the Parts container and double-click
Section Assignments in the list that appears.
2. Drag a rectangle around the hinge piece to select the entire part.
Abaqus/CAE highlights all the regions of the part.
3. Click mouse button 2 to indicate that you have Þnished selecting the regions to be assigned the
section.
The Edit Section Assignment dialog box appears containing a list of existing sections.
SolidSection is selected by default since there are no other sections currently deÞned.
4. In the Edit Section Assignment dialog box, accept the default selection of SolidSection,
and click OK.
Abaqus/CAE assigns the section to the part and colors the entire part aqua to indicate that the region
has a section assignment.
C–19
C.4 Creating and modifying a second hinge piece

The model contains a second hinge piece similar to the Þrst except that the lubrication hole is not present.
You will create a copy of the Þrst hinge piece and delete the features that form the lubrication hole.
Copying the hinge

First you will create an exact copy of the hinge piece.
To copy the hinge:

1. In the Model Tree, click mouse button 3 on Hinge-hole underneath the Parts container and select
Copy from the menu that appears.
Abaqus/CAE displays the Part Copy dialog box.
2. In the text box in the Part Copy dialog box, type Hinge-solid, and click OK.
Abaqus/CAE creates a copy of the hinge piece and names the copy Hinge-solid. The copy of the
hinge piece includes the section from the original hinge piece.
Modifying the copy of the hinge

Now you will create a solid hinge piece by deleting the features that form the lubrication hole.
To modify the copy of the hinge:

1. In the Model Tree, double-click Hinge-solid underneath the Parts container to make it current.
Abaqus/CAE displays the part in the current viewport. Look at the viewport title bar to see which
part is being displayed.
2. Expand the Features container underneath Hinge-solid.
3. Click mouse button 3 on Datum pt-1 in the list of part features.
Abaqus/CAE highlights the point, as shown in Figure C–20.
4. From the menu that appears, select Delete. When you delete a selected feature, Abaqus/CAE
asks whether you also want to delete any features that depend on the feature being deleted. The
feature being deleted is called the “parent” feature, and its dependent features are called “children.”
Abaqus/CAE highlights all the features that it will delete if the parent feature is deleted. From the
buttons in the prompt area, click Yes to delete the datum point and all its children.
Abaqus/CAE deletes the datum point. Because they were dependent on the datum point,
Abaqus/CAE also deletes the datum axis, the datum plane, and the lubrication hole.
Important: You cannot recover deleted features; however, you can temporarily remove
a feature by suppressing it.
C–20
Select datum point
Figure C–20 Delete the datum point and its children.
C.5 Creating the pin

The Þnal assembly consists of instances of the two hinge pieces that are free to rotate about a pin. You
will model the pin as a three-dimensional, revolved analytical rigid surface. First you create the pin and
assign the rigid body reference point; then you constrain the pin by applying constraints to this rigid body
reference point.
Creating the pin

You will now create the pin—a three-dimensional, revolved analytical rigid surface.
To create the pin:

1. In the Model Tree, double-click the Parts container to create a new part.
The Create Part dialog box appears.
2. Name the part Pin. Choose a three-dimensional body as before, but change the type to Analytical
rigid and the base feature shape to Revolved shell.
3. Accept the approximate size of 0.2, and click Continue.
The Sketcher starts and displays the axis of revolution as a green dashed line with a Þxed position
constraint; your sketch cannot cross this axis.
4. From the Sketcher toolbox, select the connected lines tool . Sketch a vertical line to the right
of the axis.
C–21
5. Dimension the horizontal distance from the line to the axis, and change the distance to 0.012.
6. Dimension the vertical length of the line, and change the length to 0.06.
The sketch and the resulting shaded part are shown in Figure C–21.
V 60.E-03
12.E-03
Figure C–21 Create the pin by revolving an analytical rigid surface about an axis.
Assigning the rigid body reference point

You need to assign a rigid body reference point to the pin. Because you will not assign mass or rotary
inertia to the pin, the rigid body reference point can be placed anywhere in the viewport. You use the
Load module to apply constraints to the reference point or to deÞne its motion. Motion or constraints
that you apply to the rigid body reference point are applied to the entire rigid surface.
You can either select the reference point from the part in the viewport, or you can enter its
coordinates. For the tutorial you will select the reference point from the viewport, as shown in
Figure C–22.
C–22
RP
Figure C–22 Create a rigid body reference point on the pin.
To assign the reference point:

1. From the main menu bar, select Tools Reference Point.
2. Select one of the vertices on the circumference of the pin.
Abaqus/CAE labels the vertex RP to indicate that the reference point has been assigned to it.
C.6 Assembling the model

Your next task is to create instances of your parts. A part instance can be thought of as a representation
of the original part; an instance is not a copy of a part. You can then position these part instances in a
global coordinate system to create the assembly.
An instance maintains its association with the original part. If the geometry of a part changes,
Abaqus/CAE automatically updates all instances of the part to reßect these changes. You cannot edit the
geometry of a part instance directly. The assembly can contain multiple instances of a single part; for
example, a rivet that is used repeatedly in a sheet metal assembly.
An instance may be independent or dependent. Independent part instances are meshed individually,
while the mesh of a dependent part instance is associated with the mesh of the original part. Part meshing
is discussed further in “Meshing the assembly,” Section C.11. By default, part instances are dependent.
When you create a part instance, Abaqus/CAE positions it so that the origin of the sketch that deÞned
the base feature overlays the origin of the assembly’s global coordinate system. In addition, the sketch
plane is aligned with the X–Y plane of the global coordinate system.
When you create the Þrst part instance, the Assembly module displays a graphic indicating the origin
and the orientation of the global coordinate system. You can use this graphic to help you decide how to
C–23
position a selected instance relative to the global coordinate system. For the tutorial you will keep the
hinge with the lubrication hole Þxed and move the second hinge and the pin relative to it.
Creating instances of your parts

First, you need to create the following instances:
• An instance of the hinge piece with the lubrication hole—Hinge-hole.
• An instance of the hinge piece with the lubrication hole removed—Hinge-solid.
• An instance of the pin—Pin.
To create an instance of the hinge piece with the lubrication hole:

1. In the Model Tree, expand the Assembly container. Then double-click Instances in the list that
appears to create a new part instance.
The Create Instance dialog box appears containing a list of all the parts in the current model—the
two hinge pieces and the pin in this example.
2. In the dialog box, select Hinge-hole.
Abaqus/CAE displays a temporary image of the selected part.
3. In the dialog box, click Apply.
Note: What is the difference between the OK and Apply buttons? When you click OK, the Create
Instance dialog box closes once the part is instanced. When you click Apply, the Create Instance
dialog box remains open while you create the instance and is available for you to create the next
instance. Click OK if you want to create only a single part instance; click Apply if you want to
create several part instances before moving on to a new procedure.
Abaqus/CAE creates a dependent instance of the hinge piece and displays a graphic indicating the
origin and orientation of the global coordinate system. Abaqus/CAE names the instance Hinge-
hole-1 to indicate that it is the Þrst instance of a part called Hinge-hole.
Note: The default position of a part instance is such that the origin and the X- and Y-axes of the
sketch of the base feature align with the origin and the X- and Y-axes of the global coordinate system.
For example, the base feature of the hinge piece is the original cube you created. Abaqus/CAE
positions instances of the hinge piece so that the origin of the cube sketch is located at the origin of
the global coordinate system and the X- and Y-axes align.
Creating an instance of the solid hinge piece

You will now create an instance of the solid hinge piece. To separate the solid hinge piece from the
instance of the hinge piece with the lubrication hole, you ask Abaqus/CAE to offset the new instance
along the X-axis.
C–24
To create an instance of the solid hinge piece:

1. From the Create Instance dialog box, toggle on Auto-offset from other instances.
The auto-offset function prevents new part instances from overlapping existing instances.
2. From the Create Instance dialog box, select Hinge-solid and click OK.
Abaqus/CAE closes the dialog box, creates the new dependent instance, and applies an offset
along the X-axis that separates the two hinges, as shown in Figure C–23. (For clarity the datum
geometry has been removed from the shaded view in Figure C–23 and subsequent Þgures by
selecting View Assembly Display Options Datum.)
Figure C–23 Create an instance of each hinge piece, and apply

an offset to position them in the viewport.
Positioning the solid hinge piece

In addition to the simple translate and rotate procedures, the Assembly module provides a set of tools
that allow you to position a selected part instance by deÞning the relationship between selected faces or
edges. You can select a face (or an edge) of the instance to move, called the movable part instance, and
a face (or an edge) of the instance that remains Þxed, called the Þxed part instance, and choose one of
the following position constraints:
C–25
Parallel Face
The movable instance moves until the two selected faces are parallel.
Face to Face
The movable instance moves until the two selected faces are parallel and a speciÞed clearance from
each other.
Parallel Edge
The movable instance moves until the two selected edges are parallel.
Edge to Edge
The movable instance moves until the two selected edges are colinear or a speciÞed distance from
each other.
Coaxial
The movable instance moves until the two selected faces are coaxial.
Coincident Point
The movable instance moves until the two selected points are coincident.
Parallel CSYS
The movable instance moves until the two selected datum coordinate systems are parallel.
Abaqus/CAE stores position constraints as features of the assembly, and they can be edited, deleted,
and suppressed. In contrast, translations and rotations are not stored and do not appear in the list of
features. Although position constraints are stored as features, they have no knowledge of each other; as
a consequence, a new position constraint may override a previous position constraint.
In this example you will move the solid hinge piece while the hinge piece with the lubrication hole
will remain Þxed. You will apply three types of position constraints to position the two hinge pieces
correctly.
To position the solid hinge piece:

1. First, constrain the solid hinge piece so that the two ßanges face each other. From the main menu
bar, select Constraint Face to Face.
2. From the movable part instance, select the face of the solid hinge piece shown in Figure C–24.
3. From the Þxed part instance, select the face of the hinge piece with the lubrication hole shown in
Figure C–25. Abaqus/CAE highlights the face on the movable part instance in red and the face on
the Þxed part instance in magenta.
C–26
Select this face
Figure C–24 Select a face on the movable part instance.
Select this face
Figure C–25 Select a face on the Þxed instance.
Abaqus/CAE displays red arrows on each selected face; the movable instance will be positioned
so that the arrows point in the same direction. You can change the direction of the arrow on the
movable instance if necessary.
4. From the prompt area, click Flip to change the direction of the arrow. Click OK when the arrows
point toward each other.
5. In the text box that appears in the prompt area, type the clearance (0.04) that will remain between
the two parts, as measured along the normal to the selected face of the Þxed part, and press [Enter].
Abaqus/CAE rotates the solid hinge piece so that the two selected faces are parallel to each other
and 0.04 meters apart, as shown in Figure C–26. The two pieces overlap because the position of
the solid hinge piece is not fully determined by the position constraint you have applied. You will
need to apply two more position constraints to obtain the desired position.
C–27
Figure C–26 Position 1: Constrain the ßange of the solid hinge piece
to face the ßange of the hinge piece with the lubrication hole.
6. Next, align the two ßange holes. From the main menu bar, select Constraint Coaxial.
7. Select the ßange hole on the solid hinge piece, as shown in Figure C–27. (You may Þnd it helpful
to display the wireframe view of the two pieces.)
2 Select this
face
3 1
Figure C–27 Select a cylindrical face on the movable instance.
8. Select the ßange hole on the hinge piece with the lubrication hole, as shown in Figure C–28.
Abaqus/CAE displays red arrows on each selected face.
C–28
Select this
face
2
3 1
Figure C–28 Select a cylindrical face on the Þxed instance.
9. From the prompt area, click Flip to change the direction of the arrow on the movable part instance.
Click OK when the arrow points downward.
Abaqus/CAE positions the two hinge pieces so that the two ßange holes are coaxial.
10. Use the rotate tool to look at the top view of the two pieces. Notice that the two ßanges are
now overlapping, as shown in Figure C–29.
Figure C–29 Position 2: Constrain the two ßange holes to lie along the same axis.
C–29
11. Finally, add a constraint to eliminate the overlap between the two ßanges. From the main menu bar,
select Constraint Edge to Edge.
12. Select the straight edge on the solid hinge piece shown in Figure C–30.
Select this
edge
Figure C–30 Select a straight edge on the movable instance.
13. Select the corresponding edge of the hinge piece with the lubrication hole, as shown in Figure C–31.
Select this
edge
Figure C–31 Select a straight edge on the Þxed instance.
Abaqus/CAE displays red arrows on each selected face.

14. If necessary, ßip the arrows so they point in the same direction; then click OK to apply the constraint.
Abaqus/CAE positions the two hinge pieces so that the two selected edges are colinear, as shown
in Figure C–32.
C–30
Figure C–32 Final position: Constrain an edge of each

hinge piece to lie along the same line.
Creating and positioning an instance of the pin

You will now create an instance of the pin and position it symmetrically in the ßange holes using
constraints and translation vectors. To deÞne the translation vector, you can select vertices from the
assembly or you can enter the coordinates. You can determine the translation vector using the Query
tool.
To position the pin:

1. In the Model Tree, double-click Instances underneath the Assembly container.
2. In the Create Instance dialog box, toggle off Auto-offset from other instances and create an
instance of the pin.
3. Constrain the pin to lie along the same axis as the two ßange holes. Use the Constraint Coaxial
menu as you did when you aligned the two ßange holes in the previous section. (You can select
either of the ßange holes as the cylindrical surface of the Þxed instance, and the direction of the
arrows is not important.)
Abaqus/CAE will position the pin as shown in Figure C–33.
4. From the main menu bar, select Tools Query.
The Query dialog box appears.
5. Select Distance from the list of General Queries.
6. The Distance query allows you measure the X-, Y-, and Z-components of the vector connecting
two selected points. You need to determine the distance between the end of the pin and the hinge
containing the lubrication hole; the two points to select are illustrated in Figure C–34.
C–31
RP
Figure C–33 Align the pin to be coaxial with the two ßange holes.
2. Select a point on
the end of the pin.
2
3 1
1. Select a point on the
circumference of the
flange hole.
Figure C–34 Determining the position of the pin.
a. To deÞne one end of the vector, select a point on the circumference of the hole in the ßange
containing the lubrication hole.
b. To deÞne the other end of the vector, select the vertex on the pin that is inside the hinge
containing the lubrication hole.
Abaqus/CAE displays the vector distance between the two selected points along with the X-, Y-,
and Z-components of the vector in the message area. You will translate the pin along the Z-axis;
C–32
the Z-component of the distance is 0.01 meters. You want to position the pin symmetrically
between the hinges, so you will translate it 0.02 meters.
7. From the main menu bar, select Instance Translate.
8. Select the pin as the part instance to move, and click Done to indicate that you have Þnished
selecting instances to move.
9. In the text boxes in the prompt area, enter a start point for the translation vector of 0,0,0 and an
end point of 0,0,0.02.
Abaqus/CAE translates the pin a distance of 0.02 along the Z-axis and displays a temporary image
of the new position of the pin.
Note: If the position of a temporary image (colored red) is not correct, you can use the buttons in the
prompt area to correct the problem. Click either the Cancel button ( ) to cancel the procedure
or the Previous button ( ) to step back through the procedure.

10. From the prompt area, click OK.
The Þnished assembly is shown in Figure C–35.
RP
Figure C–35 Shaded view of the Þnished assembly.
11. Before proceeding, convert all position constraints to absolute positions. From the main menu bar,
select Instance Convert Constraints. Select all part instances, and click Done in the prompt
area.
C–33
C.7 Defining analysis steps

Before you apply loads or boundary conditions to the model or deÞne contact within the model, you
must deÞne the different steps in the analysis. Once the steps are created, you can specify in which steps
loads, boundary conditions, and interactions should be applied.
When you create a step, Abaqus/CAE selects a default set of output variables corresponding to the
analysis procedure and selects a default rate at which the variables are written to the output database. In
this tutorial you will edit the default output frequency for the Þrst step and edit the list of default output
variables for the second step.
Creating the analysis steps

The analysis that you perform on the hinge model will consist of an initial step and two general analysis
steps:
• In the initial step you apply boundary conditions to regions of the model and deÞne contact between
regions of the model.
• In the Þrst general analysis step you allow contact to become established.
• In the second general analysis step you modify two of the boundary conditions applied to the model
and apply a pressure load to one of the hinge pieces.
Abaqus/CAE creates the initial step by default, but you must create the two analysis steps.
To create the analysis steps:

1. In the Model Tree, double-click the Steps container to create a new step.
The Create Step dialog box appears.
2. In the Create Step dialog box:
a. Name the step Contact.
b. Accept the default procedure type (Static, General), and click Continue.
The step editor appears.
3. In the Description Þeld, type Establish contact.
4. Click the Incrementation tab, and delete the value of 1 that appears in the Initial text Þeld. Type
a value of 0.1 for the initial increment size.
5. Click OK to create the step and to exit the editor.
The Contact step appears underneath the Steps container in the Model Tree.
6. Use the same technique to create a second general, static step named Load. Enter Apply load
in the description Þeld and an initial increment size of 0.1.
The Load step appears underneath the Steps container in the Model Tree.
C–34
Requesting output
You use Þeld output requests to request output of variables that should be written at relatively low
frequencies to the output database from the entire model or from a large portion of the model. Field
output is used to generate deformed shape plots, contour plots, and animations from your analysis results.
Abaqus/CAE writes every component of the variables to the output database at the selected frequency.
You use history output requests to request output of variables that should be written to the output
database at a high frequency from a small portion of the model; for example, the displacement of a single
node. History output is used to generate X–Y plots and data reports from your analysis results. When
you create a history output request, you must select the individual components of the variables that will
be written to the output database.
The default Þeld output variables for the Contact and Load steps include the following:
• S (Stress components)
• PE (Plastic strain components)
• PEEQ (Equivalent plastic strain)
• PEMAG (Plastic strain magnitude)
• LE (Logarithmic strain components)
• U (Translations and rotations)
• RF (Reaction forces and moments)
• CF (Concentrated forces and moments)
• CSTRESS (Contact stresses)
• CDISP (Contact displacements)
By default, Abaqus/CAE writes the default Þeld output variables from a static, general procedure to the
output database after every increment of a step. In the following procedure you will change the output
frequency during the Contact step so that data are written to the output database once—at the last
increment of the step. In addition, you will delete the request for CDISP during the Load step, since it
is not needed for postprocessing.
To edit an output request and to specify the output frequency during the Load step:
1. In the Model Tree, click mouse button 3 on the Field Output Requests container and select
Manager from the menu that appears.
The Field Output Requests Manager appears. The Field Output Requests Manager is
a step-dependent manager. The types of objects that appear in step-dependent managers are
those that you can create, modify, and deactivate in particular analysis steps. Step-dependent
managers display information concerning the history of each object listed in the manager. In this
example Abaqus/CAE named the default Þeld output request that you created in the Contact
step F-Output-1. In addition Abaqus/CAE propagated the output request into the Load step. For
more information, see “Managing objects,” Section 3.4 of the Abaqus/CAE User’s Manual.
C–35
2. From the Field Output Requests Manager, select the F-Output-1 output request in the Contact
step. From the buttons on the right side of the manager, click Edit.
The Edit Field Output Request editor appears for the Contact step.
3. Select Last increment as the output frequency to generate output only during the last increment
of the step.
4. Click OK to modify the output request.
5. From the Field Output Requests Manager, select the F-Output-1 output request in the Load
step and click Edit.
The Edit Field Output Request editor appears for the Load step.
6. Set the output frequency to 1 to generate output during every increment of the step.
7. From the list of output categories, click the arrow to the left of Contact.
A list of the contact output variables available appears along with a description of each.
8. Click the check box next to CDISP to deselect this variable for output.
The check box next to Contact remains light gray with a dark gray check mark to indicate that not
all variables in this category will be output. The Edit Field Output Request editor also indicates
the following:
• Output will be generated for the whole model.
• Output will be generated at default section points.
• Output will include local coordinate transformations (when available).
9. Click OK to modify the output request.
In the Field Output Requests Manager the status of the output request changes to Modified for
the Load step.
10. At the bottom of the Field Output Requests Manager, click Dismiss to close the dialog box.
Selecting a degree of freedom to monitor

You can deÞne particular element or node sets that contain only selected portions of your model. Once
you create a set, you can use it to perform the following tasks:
• Assign section properties in the Property module.
• Create contact pairs with contact node sets and surfaces in the Interaction module.
• DeÞne loads and boundary conditions in the Load module.
• Request output to either the output database or the status Þle from speciÞc regions of the model in
the Step module. Output to the status Þle is also reported back to the Job module in the form of a
continuously updated X–Y plot.
• Display results for speciÞc regions of the model in the Visualization module.
C–36
In this example you will deÞne a node set consisting of a single node. You will then be able to monitor
the results for one degree of freedom at that node when you submit your job for analysis later in this
tutorial.
To create a set and monitor a particular degree of freedom:
1. In the Model Tree, expand the Assembly container and double-click the Sets item.
The Create Set dialog box appears.
2. Name the set Monitor, and click Continue.
3. Select the vertex of the solid hinge piece shown in Figure C–36.
Select
this vertex
Figure C–36 Monitor a degree of freedom on the solid hinge piece.
4. Click Done to indicate that you have Þnished selecting the geometry for the set.
Abaqus/CAE creates a node set with the name Monitor that contains the node you selected.
5. From the main menu bar of the Step module, select Output DOF Monitor.
The DOF Monitor dialog box appears.
6. Toggle on Monitor a degree of freedom throughout the analysis.
7. Click Edit, then click Points in the prompt area and choose the node set Monitor from the Region
Selection dialog box.
8. Type 1 in the Degree of freedom text Þeld, and click OK.
C.8 Creating surfaces to use in contact interactions

Now you will deÞne contact between regions of the model. There are two approaches that can be
adopted to deÞne contact interactions. The Þrst is a manual approach that requires you to identify
which surfaces will form part of the contact interactions and to deÞne the individual contact pairs. An
C–37
alternative approach is to let Abaqus/CAE automatically identify and deÞne all potential contact pairs.
The latter approach is desirable for complicated models containing many contact interactions. The
automatic contact deÞnition option is available only for three-dimensional Abaqus/Standard models.
In “DeÞning contact between regions of the model,” Section C.9, you will be given the option to
deÞne the contact interactions either manually (where you will use the surfaces deÞned in the following
instructions) or automatically (in which case the surfaces deÞned below are not used; Abaqus/CAE will
choose the surfaces automatically). For instructional purposes, however, you are encouraged to complete
the surface deÞnition instructions that follow regardless of the approach you choose to deÞne the contact
interactions.
When manually deÞning contact interactions, the Þrst step is to create the surfaces that you will
include later in interactions. It is not always necessary to create your surfaces in advance; if the model
is simple or the surfaces easy to select, you can indicate the master and slave surfaces directly in the
viewport as you create the interactions. However, in this tutorial it is easier to deÞne the surfaces
separately and then refer to the names of those surfaces when you create the interactions. You will
deÞne the following surfaces:
• A surface named Pin that includes the outside surface of the pin.
• Two surfaces named Flange-h and Flange-s that include the two ßange faces that contact each
other.
• Two surfaces named Inside-h and Inside-s that include the inside surfaces of the ßanges that
contact the pin.
Defining a surface on the pin

In this section you will deÞne the outside surface of the pin. You will Þnd it helpful to display only one
part at a time while you select the surfaces to be deÞned.
To display only a single part instance in the assembly:

1. From the main menu bar, select View Assembly Display Options.
The Assembly Display Options dialog box appears.
2. Click the Instance tab.
The part instances that you have created are listed with check marks in the Visible column. All the
part instances are visible by default.
3. Click in the Visible column next to Hinge-hole-1 and Hinge-solid-1, and click Apply.
The hinge pieces disappear from the view.
To define a surface on the pin:

1. In the Model Tree, expand the Assembly container and double-click the Surfaces item.
The Create Surface dialog box appears.
C–38
2. In the dialog box, name the surface Pin and click Continue.
3. In the viewport, select the pin.
4. Click mouse button 2 in the viewport to indicate that you have Þnished selecting regions for the
surface.
Each side of the hollow cylinder representing the pin has a different color associated with it. In
Figure C–37 the outside of the pin is colored brown and the inside of the pin is colored purple. The
colors may be reversed on your model, depending on how you created the original sketch for the
pin.
Figure C–37 Select the region to be deÞned as the surface Pin.
5. You must choose whether the surface consists of the inside or the outside of the cylinder. The
outside surface contacts the two hinges and is the desired choice. From the buttons in the prompt
area, click the color (Brown or Purple) associated with the outside surface.
Abaqus/CAE creates the desired surface called Pin and displays it underneath the Surfaces
container in the Model Tree.
Defining the surfaces on the hinge pieces

In this section you will deÞne the surfaces on the hinge pieces needed to deÞne contact between the two
hinge pieces and between the hinge pieces and the pin.
To define the surfaces on the hinge pieces:

1. From the Assembly Display Options dialog box, change the visibility settings so that only
Hinge-hole-1 is visible.
Abaqus/CAE displays only the hinge piece with the lubrication hole in the viewport.
2. In the Model Tree, double-click Surfaces underneath the Assembly container.
The Create Surface dialog box appears.
C–39
3. In the dialog box, name the surface Flange-h and click Continue.
4. On the instance with the lubrication hole, select the face of the ßange that contacts the other ßange,
as shown by the gridded face in Figure C–38. (You may need to rotate the view to see this face
clearly.)
Figure C–38 Select the region to be deÞned as the surface Flange-h.
5. When you have selected the desired face, click mouse button 2 to conÞrm your selection.
Abaqus/CAE creates the desired surface called Flange-h and displays it underneath the Surfaces
container in the Model Tree.
6. Create a surface called Inside-h that includes the cylindrical inner surface of the hinge piece
with the lubrication hole, as shown in Figure C–39. (You may need to zoom in on the view to select
this face.)
Select
this surface
Figure C–39 Select the region to be deÞned as the surface Inside-h.
C–40
7. Change the visibility settings so that only Hinge-solid-1 is visible.

8. Use similar techniques to create a surface called Flange-s that contains the corresponding face
of the solid hinge piece’s ßange.
9. Finally, create a surface called Inside-s that includes the cylindrical inner surface of the solid
hinge piece.
10. In the Assembly Display Options dialog box, click Defaults to return to the default visibility
settings and click OK to close the dialog box.
C.9 Defining contact between regions of the model

Interactions are objects that you create to model mechanical relationships between surfaces that are in
contact or closely spaced. Mere physical proximity of two surfaces on an assembly is not enough to
indicate any type of interaction between the surfaces.
You will deÞne the following interactions:
• An interaction called HingePin-hole that deÞnes the contact between the part instance Hinge-
hole-1 and the pin.
• An interaction called HingePin-solid that deÞnes the contact between the part instance
Hinge-solid-1 and the pin.
• An interaction called Flanges that deÞnes the contact between the two ßanges.
Each of these interactions requires a reference to an interaction property. Interaction properties
are collections of information that help you to deÞne certain types of interactions. You will create a
mechanical interaction property that describes the tangential and normal behavior between all surfaces
as frictionless. You will name this property NoFric and use it in all three of the interactions.
Creating an interaction property

In this procedure you will create a mechanical contact interaction property.
To create the interaction property:

1. In the Model Tree, double-click the Interaction Properties container to create a contact property.
The Create Interaction Property dialog box appears.
2. In the Create Interaction Property dialog box:
a. Name the property NoFric.
b. In the Type list, accept Contact as the default selection.
c. Click Continue.
The Edit Contact Property dialog box appears.
C–41
3. From the dialog box’s menu bar, select Mechanical Tangential Behavior and accept
Frictionless for the friction formulation.
4. Click OK to save your settings and to close the Edit Contact Property dialog box.
Creating the interactions

In this section you will create three mechanical surface-to-surface contact interactions. Each interaction
will refer to the interaction property that you just created. You are given the option to deÞne the
interactions either automatically or manually. Please follow the instructions for one method or the other.
If you choose to try both, be sure to delete or suppress any duplicate contact interactions that result.
To create the interactions automatically:

1. From the main menu bar, select Interaction Find contact pairs.
2. In the Find Contact Pairs dialog box, click Find Contact Pairs.
Five potential contact pairs are identiÞed.
3. In the Contact Pairs region of the dialog box:
a. Click the name of each contact pair to highlight it in the viewport. This will allow you to
familiarize yourself with the contact interactions that have been chosen.
b. Contact pairs are deÞned between the rounded end of each hinge ßange and the ßat face
opposite it. These contact pairs are not necessary. Thus, delete them (to delete a contact pair,
select it and click mouse button 3; from the menu that appears, select Delete).
c. Identify the contact pair between the hinge with the hole and the pin. Rename the interaction
HingePin-hole.
d. Identify the contact pair between the solid hinge and the pin. Rename the interaction
HingePin-solid.
e. Rename the remaining interaction Flanges. If necessary, switch the master and slave surface
designations so that the surface associated with the hinge with the hole is the master surface
and the one associated with the solid hinge piece is the slave surface (click mouse button 3 on
the surface name; from the menu that appears, select Switch surfaces).
Tip: You can view the master and slave instance names to aid in the surface
designation. Click mouse button 3 anywhere on the table, and select Edit Visible
Columns. From the dialog box that appears, toggle on Master instance name
and Slave instance name.
f. Accept all default settings except for the contact discretization. Select the column heading
labeled Discretization and click mouse button 3. From the menu that appears, select Edit
cells. In the dialog box that appears, select Node-to-surface and click OK.
g. Click OK to save the interactions and to close the dialog box.
C–42
To create the interactions manually:

1. In the Model Tree, click mouse button 3 on the Interactions container and select Manager from
the menu that appears.
The Interaction Manager appears.
2. From the lower-left corner of the Interaction Manager, click Create.
The Create Interaction dialog box appears.
3. In the dialog box:
a. Name the interaction HingePin-hole.
b. Select Initial from the list of steps.
c. In the Types for Selected Step list, accept the default selection of Surface-to-surface
contact (Standard).
d. Click Continue.
The Region Selection dialog box appears containing a list of the surfaces that you deÞned earlier.
Note: If the Region Selection dialog box does not appear automatically, click the Surfaces
button on the far right side of the prompt area.
4. In the Region Selection dialog box, select Pin as the master surface, and click Continue.
5. From the buttons in the prompt area, select Surface as the slave type.
6. In the Region Selection dialog box, select Inside-h as the slave surface, and click Continue.
The Edit Interaction dialog box appears.
a. Accept the default Sliding formulation selection of Finite sliding.
b. Accept the default Slave Node Adjustment selection of No adjustment.
c. Accept NoFric as the interaction property. (If more properties were deÞned, you could click
the arrow next to the Contact interaction property Þeld to see the list of available properties
and select the property of your choice.)
d. Click OK to save the interaction and to close the dialog box.
The interaction that you created appears in the Interaction Manager.
8. Use the same techniques explained in the previous steps to create a similar interaction called
HingePin-solid. Use Pin as the master surface, Inside-s as the slave surface, and
NoFric as the interaction property.
9. Create a similar interaction called Flanges. Use Flange-h as the master surface, Flange-s
as the slave surface, and NoFric as the interaction property.
10. From the Interaction Manager, click Dismiss to close the manager.
C–43
C.10 Applying boundary conditions and loads to the assembly

You will apply the following boundary conditions and load to the hinge model:
• A boundary condition called Fixed that constrains all degrees of freedom at the end of the hinge
piece with the lubrication hole, as shown in Figure C–40.
constrain
this face
2
3 1
Figure C–40 One end of the hinge is constrained.
• A boundary condition called NoSlip that constrains all degrees of freedom of the pin while
contact is established during the Þrst analysis step. You will modify this boundary condition in the
second analysis step (the step in which the load is applied) so that degrees of freedom 1 and 5 are
unconstrained. Figure C–41 illustrates this boundary condition applied at the reference point.
• A boundary condition called Constrain that constrains all degrees of freedom of a point on the
solid hinge piece during the Þrst analysis step. You will modify this boundary condition in the
second analysis step so that degree of freedom 1 is unconstrained when the load is applied.
• A load called Pressure that you apply to the end of the solid hinge piece during the second
analysis step. Figure C–42 illustrates the constraint and the pressure load applied to the solid hinge.
Constraining the hinge piece with the lubrication hole

You will apply a boundary condition to the face at the end of the hinge piece with the lubrication hole to
Þx the hinge piece in place during the analysis.
C–44
RP
Figure C–41 The pin is constrained.
constrain
this node
apply a negative
2 pressure load
to this face
3 1
Figure C–42 The second hinge is constrained and loaded.
To constrain the hinge piece with the lubrication hole:

1. In the Model Tree, click mouse button 3 on the BCs container and select Manager from the menu
that appears.
The Boundary Condition Manager dialog box appears.
2. In the Boundary Condition Manager, click Create.
The Create Boundary Condition dialog box appears.
3. In the Create Boundary Condition dialog box:
a. Name the boundary condition Fixed.
b. Accept Initial from the list of steps.
C–45
c. Accept Mechanical as the default Category selection.

d. Select Displacement/Rotation as the type of boundary condition for the selected step.
e. Click Continue.
The Region Selection dialog box appears.
f. From the right side of the prompt area, click Select in Viewport to select the object directly
from the viewport.
The Region Selection dialog box closes.
4. Select the gridded face shown in Figure C–43 as the region where the boundary condition will be
applied.
Figure C–43 Apply a boundary condition to the end of the hinge piece with the lubrication hole.
By default, Abaqus/CAE selects only objects that are closest to the front of the screen, and you
cannot select the desired face unless you rotate the hinge. However, you can use the selection
options to change this behavior.
a. From the Selection toolbar, toggle off the closest object tool .
b. Click over the desired face.
Abaqus/CAE displays Next, Previous, and OK buttons in the prompt area.
c. Click Next and Previous until the desired face is highlighted.
d. Click OK to conÞrm your choice.
5. Click mouse button 2 to indicate that you have Þnished selecting regions.
The Edit Boundary Condition dialog box appears.
C–46

a. Toggle on the buttons labeled U1, U2, and U3 to constrain the end of the hinge in the 1-, 2-,
and 3-directions. You do not need to constrain the rotational degrees of freedom of the hinge
because solid elements (which have only translational degrees of freedom) will be used to mesh
the hinge.
b. Click OK to close the dialog box.
The boundary condition that you just created appears in the Boundary Condition Manager,
and arrows appear on the nodes of the face indicating the constrained degrees of freedom. The
Boundary Condition Manager shows that the boundary condition remains active in all steps of
the analysis.
Tip: You can suppress the display of boundary condition arrows in the same way that
you suppress the visibility of part instances. Click the Attribute tab in the Assembly
Display Options dialog box to see the boundary condition display options.
Constraining the pin

In the Þrst general step of the analysis you will establish contact between the two hinge pieces and
between the hinge pieces and the pin. To Þx the pin during this step, you must apply a boundary condition
to the pin that constrains all its degrees of freedom.
To apply a boundary condition to the pin:

1. In the Boundary Condition Manager, click Create.
The Create Boundary Condition dialog box appears.
2. In the Create Boundary Condition dialog box:
a. Name the boundary condition NoSlip.
b. Accept Initial in the Step text Þeld.
c. Accept Mechanical as the default Category selection.
d. Select Displacement/Rotation as the type of boundary condition for the selected step.
e. Click Continue.
3. In the viewport, select the rigid body reference point on the pin as the region where the boundary
condition will be applied.
The Edit Boundary Condition dialog box appears.
a. Toggle on all the buttons to constrain all the degrees of freedom of the pin.
C–47
b. Click OK.
The new boundary condition appears in the Boundary Condition Manager.
Modifying the boundary condition applied to the pin

Objects that you can create and modify in certain steps—such as boundary conditions, loads, and
interactions—have special managers that allow you to modify objects and change their status in
different analysis steps.
In this section you will use the boundary condition manager to modify the boundary condition
NoSlip so that translation in the 1-direction and rotation about the 2-axis are unconstrained during the
loading step.
Currently the Boundary Condition Manager displays the names of the two boundary conditions
that you have created as well as their status in each step: both boundary conditions are Created in the
initial step and Propagated through the following analysis steps.
To modify a boundary condition:

1. In the Boundary Condition Manager, click the cell labeled Propagated that lies in the row
labeled NoSlip and in the column labeled Load, as shown in Figure C–44. That cell becomes
highlighted.
Figure C–44 Select boundary conditions to edit in the Boundary Condition Manager.
2. On the right side of the manager, click Edit to indicate that you want to edit the NoSlip boundary
condition in the Load step.
The Edit Boundary Condition dialog box appears, and Abaqus/CAE displays a set of arrows on
the model indicating where the boundary condition is applied and which degrees of freedom are
constrained.
3. In the editor, toggle off the buttons labeled U1 and UR2 so that the pin is allowed to translate in the
1-direction and rotate about the 2-axis. Click OK to close the dialog box.
In the Boundary Condition Manager, the status of the NoSlip boundary condition in the Load
step changes to Modified.
C–48
Constraining the solid hinge piece

In the Þrst analysis step, in which contact is established, you will constrain a single node of the solid
hinge piece in all directions. These constraints, along with contact with the pin, are enough to prevent
rigid body motion of the solid piece. In the second analysis step, in which the load is applied to the
model, you will remove the constraint in the 1-direction.
To constrain the solid hinge piece:

1. Create a displacement boundary condition in the Initial step, and call it Constrain.
2. Apply the boundary condition to the vertex selected from the solid hinge piece, as shown in
Figure C–45.
Select
this vertex
Figure C–45 Apply a boundary condition to a vertex of the solid hinge piece.
3. Constrain the vertex in the 1-, 2-, and 3-directions.

4. In the Load step, modify the boundary condition so that the hinge is unconstrained in the
1-direction.
5. When you have Þnished creating boundary conditions, click Dismiss to close the Boundary
Condition Manager.
Applying a load to the solid hinge

Next, you apply a pressure load to the face at the end of the solid hinge. You apply the load in the
1-direction during the second analysis step.
C–49
To apply a load to the solid hinge:

1. In the Model Tree, double-click the Loads container to create a new load.
The Create Load dialog box appears.
2. In the Create Load dialog box:
a. Name the load Pressure.
b. Accept Load as the default selection in the Step text Þeld.
c. From the Category list, accept Mechanical as the default selection.
d. From the Types for Selected Step list, select Pressure.
e. Click Continue.
3. In the viewport, select the face at the end of the solid hinge piece as the surface to which the load
will be applied, as shown by the gridded surface in Figure C–46.
Figure C–46 Apply a load to the solid hinge piece.
The Edit Load dialog box appears.
5. In the dialog box, enter a magnitude of −1.E6 for the load, and click OK.
Arrows appear on the face indicating the applied load. The arrows are pointing out of the face
because you applied a negative pressure.
C.11 Meshing the assembly

Meshing the assembly is divided into the following operations:
• Making sure the part instances can be meshed and creating additional partitions where necessary.
C–50
• Assigning mesh attributes to the part instances.

• Seeding the part instances.
• Meshing the part instances.
Deciding what needs to be partitioned

When you enter the Mesh module, Abaqus/CAE color codes regions of the model according to the
methods it will use to generate a mesh:
• Green indicates that a region can be meshed using structured methods.
• Yellow indicates that a region can be meshed using sweep methods.
• Orange indicates that a region cannot be meshed using the default element shape assignment
(hexahedral) and must be partitioned further. (Alternatively, you can mesh any model by assigning
tetrahedral elements to the model and using the free meshing technique.)
For the tutorial Abaqus/CAE indicates that the hinge with the lubrication hole needs to be partitioned
to be meshed using hexahedral-shaped elements. SpeciÞcally, areas surrounding the hole in the ßange
must be partitioned. The partitioned hinges are shown in Figure C–47.
3 1
Figure C–47 The partitioned hinges.
Use the following techniques to help you select faces and vertices during the partitioning process:
• Use a combination of the view manipulation tools, the display option tools in the View Options
toolbar, and the tools in the Views toolbar to resize and reposition the model as necessary. (To
display the Views toolbar, select View Toolbars Views from the main menu bar.)
• Toggle off the closest object tool in the Selection toolbar to cycle through the possible
selections using the Next and Previous buttons in the prompt area.
C–51
• You will probably Þnd the 3D compass and/or the magniÞcation tool and the rotation tool
especially useful.
• When necessary, click the Iso tool in the Views toolbox to return the model to its original size and
position in the viewport.
• Recall that part instances are classiÞed as dependent by default. All dependent instances of a part
must possess identical geometry (including partitions) and meshes. To satisfy this requirement, all
partitions must be created in the original part and all mesh attributes must be assigned to the original
part. You will need to examine the parts individually to determine what action (if any) needs to be
taken to create a mesh using hexahedral elements.
Note: The advantage of dependent part instances is that if you create multiple instances of the same
part, you need only manipulate and mesh the original part; these features are automatically inherited
by the dependent instances. Since you created only one instance of each part in this tutorial, you
could have created independent part instances and worked with them just as easily. This would have
allowed you to create partitions and assign mesh attributes at the assembly level rather than at the
part level. You can make a dependent part instance independent by clicking mouse button 3 on its
name underneath the Instances container in the Model Tree and selecting Make independent. In
what follows, we assume the part instances remain dependent.
To decide what needs to be partitioned:

1. In the Model Tree, expand Hinge-hole underneath the Parts container and double-click Mesh in
the list that appears.
Note: If the part instance were independent, you would instead expand the instance name
underneath the Instances container and click Mesh in the list that would appear.
Abaqus/CAE displays the hinge piece with the lubrication hole. The cube portion of the hinge piece
is colored green to indicate that it can be meshed using the structured meshing technique; the ßange
with the lubrication hole is colored orange to indicate that it needs to be partitioned to be meshed
using hexahedral elements, as shown in Figure C–48. The partitioning procedure is described in
“Partitioning the ßange with the lubrication hole,” Section C.11.2.
2. Use the Object Þeld that appears in the context bar to display the solid hinge in the viewport.
Abaqus/CAE displays the solid hinge. As before, the cube portion of the solid hinge piece is colored
green to indicate that it can be meshed using the structured meshing technique. The ßange without
the lubrication hole is colored yellow to indicate that it can be meshed using a swept mesh.
3. Select the pin from the Object Þeld in the context bar. Abaqus/CAE displays the pin in orange
because it is an analytical rigid surface and cannot be meshed.
Thus, the hinge piece with the lubrication hole needs to be partitioned to be meshed with hexahedral
elements; the solid hinge and the pin require no further action.
C–52
Figure C–48 The ßange with the lubrication hole cannot be meshed.
Partitioning the flange with the lubrication hole

For Abaqus/CAE to mesh the ßange with the lubrication hole, it must be partitioned into the regions
shown in Figure C–49.
3 1
Figure C–49 Shaded view of the partitioned ßange.
To partition the flange with the lubrication hole:

1. From the main menu, select Tools Partition.
The Create Partition dialog box appears.
C–53
2. You want to partition the entire cell that makes up the ßange. From the Create Partition dialog
box, select Cell as the Type of partition and click Define cutting plane as the partition Method.
3. Select the ßange of the hinge with the lubrication hole. Click Done to indicate you have Þnished
selecting cells.
Abaqus/CAE provides three methods for specifying the cutting plane:
• Select a point and a normal. The cutting plane passes through the selected point, normal to the
selected edge.
• Select three non-colinear points. The cutting plane passes through each point.
• Select an edge and a point along the edge. The cutting plane passes through the selected point,
normal to the selected edge.
The cutting plane need not be deÞned in the cell being partitioned. The plane extends inÞnitely and
partitions the selected cell anywhere there is an intersection.
4. From the buttons in the prompt area, select 3 points.
Abaqus/CAE highlights points that you can select.
5. Select three points that cut the ßanges in half with a vertical partition, as shown in Figure C–50.
Tip: You may Þnd it easier to select the desired points if you magnify, rotate, and pan the
model to obtain a more convenient view.
Figure C–50 Select three points to use in partitioning the ßanges.
6. From the prompt area, click Create Partition.

Abaqus/CAE creates the desired partitions.
The ßange regions are colored yellow, indicating that no additional partitions are required to create
a hexahedral mesh. Thus, the partitioning operation is complete.
C–54
7. Select Assembly in the Object Þeld of the context bar to display the model assembly in the
viewport. The model assembly with all the partitions is shown in Figure C–51.
RP
3 1
Figure C–51 The partitioned model.
Assigning mesh controls

In this section you will use the Mesh Controls dialog box to examine the techniques that Abaqus/CAE
will use to mesh the parts and the shape of the elements that Abaqus/CAE will generate.
You cannot mesh an analytical rigid surface. As a result you cannot apply mesh controls to an
analytical rigid surface; neither can you seed it or assign an element type to it. Thus, you need only
concern yourself with the hinge pieces. Since the instances are dependent on the original part deÞnition,
you must assign mesh attributes (controls, type, and seed size) to each hinge piece individually. For
convenience, you will begin with the hinge piece with the lubrication hole.
To assign the mesh controls:

1. Make the hinge piece with the hole current in the viewport. From the main menu bar, select
Mesh Controls.
2. Drag a square around the part to select all regions of the part, and click Done to indicate your
selection is complete.
The hinge piece appears red in the viewport to indicate that you have selected it, and Abaqus/CAE
displays the Mesh Controls dialog box.
3. In the dialog box, accept Hex as the default Element Shape selection.
4. Select Sweep as the meshing technique that Abaqus/CAE will apply.
C–55
5. Select Medial axis as the meshing algorithm.

6. Click OK to assign the mesh controls and to close the dialog box.
The entire hinge will appear in yellow, indicating that it will be meshed using the swept meshing
technique.
7. Click Done in the prompt area.
8. Repeat the above steps for the solid hinge piece.
Assigning the Abaqus element type

In this section you will use the Element Type dialog box to examine the element types that are assigned
to each part. For convenience, you will begin with the hinge piece with the lubrication hole.
To assign an Abaqus element type:

Mesh Element Type.
2. Select the hinge piece using the same technique described in the mesh controls procedure, and click
Done to indicate your selection is complete.
Abaqus/CAE displays the Element Type dialog box.
3. In the dialog box, accept Standard as the Element Library selection.
4. Accept Linear as the Geometric Order selection.
5. Accept 3D Stress as the default Family of elements.
6. Click the Hex tab, and select Reduced Integration as the Element Controls method if it is not
already selected.
A description of the default element type, C3D8R, appears at the bottom of the dialog box.
Abaqus/CAE will now associate C3D8R elements with the elements in the mesh.
7. Click OK to assign the element type and to close the dialog box.
Seeding the part instances

The next step of the meshing process is to seed each of the part instances. Seeds represent the approximate
locations of nodes and indicate the target density of the mesh you would like to generate. You can select
seeding based on the number of elements to generate along an edge or on the average element size, or
you can bias seed distribution toward one end of an edge. For the tutorial you will seed the parts so that
the hinge pieces have an average element size of 0.004. For convenience, you will begin with the hinge
piece with the lubrication hole.
C–56
To seed the parts:

Seed Part.
2. In the Global Seeds dialog box that appears, enter an approximate global element size of 0.004,
and click OK.
Seeds appear on all the edges.
Note: If you are using the Abaqus Student Edition, using a global seed size of 0.004 results in a
mesh that exceeds the model size limits of the product. Use a global seed size of 0.008 instead.
You are now ready to mesh the parts.
Meshing the assembly

In this section you will mesh the parts. For convenience, you will begin with the hinge piece with the
lubrication hole.
To mesh the assembly:

Mesh Part.
2. Click Yes in the prompt area to create the mesh.
Abaqus/CAE meshes the part.
The meshing operations are now complete. Display the model assembly in the viewport to see the
Þnal mesh, as illustrated in Figure C–52.
C.12 Creating and submitting a job

Now that you have conÞgured your analysis, you will create a job that is associated with your model and
submit the job for analysis.
To create and submit an analysis job:

1. In the Model Tree, double-click the Jobs container to create a job.
The Create Job dialog box appears.
2. Name the job PullHinge, and click Continue.
The job editor appears.
C–57
RP
3 1
Figure C–52 Final view of the meshed model.
3. In the Description Þeld, type Hinge tutorial.

Click the tabs to see the contents of the job editor, and review the default settings. Click OK to
accept all the default job settings.
4. In the Model Tree, click mouse button 3 on the job named PullHinge and select Submit from the
menu that appears to submit your job for analysis.
5. In the Model Tree, click mouse button 3 on the job name and select Monitor from the menu that
appears to monitor the analysis as it runs.
A dialog box appears with the name of your job in the title bar and a status chart for the analysis.
Messages appear in the lower panel of the dialog box as the job progresses. Click the Errors and
Warnings tabs to check for problems in the analysis.
Once the analysis is underway, an X–Y plot of the values of the degree of freedom that you selected
to monitor earlier in the tutorial appears in a separate window in the viewport. (You may need to
resize the viewport windows to see it.) You can follow the progression of the node’s displacement
over time in the 1-direction as the analysis runs.
6. When the job completes successfully, the status of the job appearing in the Model Tree changes to
Completed. You are now ready to view the results of the analysis with the Visualization module.
In the Model Tree, click mouse button 3 on the job name and select Results from the menu that
appears.
Abaqus/CAE enters the Visualization module, opens the output database created by the job, and
displays the undeformed shape of the model.
Note: You can also enter the Visualization module by clicking Visualization in the Module list
located in the context bar. However, in this case Abaqus/CAE requires you to open the output
database explicitly using the File menu.
C–58
C.13 Viewing the results of your analysis

You will view the results of your analysis by drawing a contour plot of the deformed model. You will
then use display groups to display one of the hinge pieces; by displaying just a portion of the model you
can view results that are not visible when you display the whole model.
Displaying and customizing a contour plot

In this section you will display a contour plot of the model and adjust the deformation scale factor.
To display a contour plot of the model:
1. From the main menu bar, select Plot Contours On Deformed Shape.
Abaqus/CAE displays a contour plot of von Mises stress superimposed on the deformed shape of
the model at the end of the last increment of the loading step, as indicated by the following text in
the state block:
Step: Load, Apply load
Increment 6: Step Time = 1.000
By default, all surfaces with no results (in this case, the pin) are displayed in white.
The deformation is exaggerated because of the default deformation scale factor that Abaqus/CAE
selects.
2. To remove the white surfaces from the display, do the following:
a. In the Results Tree, expand the Surface Sets container underneath the output database Þle
named PullHinge.odb.
b. Select all the surfaces that appear in the list.
c. Click mouse button 3, and select Remove from the menu that appears.
The white surfaces disappear from the view.
3. To reduce the deformation scale factor, do the following:
a. From the main menu bar, select Options Common.
The Common Plot Options dialog box appears.
b. From the Deformation Scale Factor options, choose Uniform.
c. In the Value text Þeld, type a value of 100; and click OK.
Abaqus/CAE displays the contour plot with a deformation scale factor of 100, as shown in
Figure C–53.
4. Use the view manipulation tools to examine the deformed model. Note where the pin appears to be
exerting the most pressure against the insides of the ßanges. Also note how the two ßanges have
twisted away from each other.
C–59
S, Mises
(Avg: 75%)
+2.576e+07
+2.362e+07
+2.147e+07
+1.933e+07
+1.718e+07
+1.504e+07
+1.290e+07
+1.075e+07
+8.606e+06
+6.462e+06
+4.317e+06
+2.173e+06
+2.824e+04
Step: Load, Apply load

3 1 Increment 6: Step Time = 1.000
Primary Var: S, Mises
Deformed Var: U Deformation Scale Factor: +1.000e+02
Figure C–53 Contour plot of von Mises stress with a reduced deformation scale factor.
5. By default, the contour plot displays the von Mises stresses in the model. You can view other
variables by selecting Result Field Output.
The Field Output dialog box appears.
6. Click the Primary Variable tab of the Field Output dialog box, and select S11 from the list of
Component options. Click Apply to see a contour plot of the stresses in the 1-direction.
7. From the Invariant option list, select Max. Principal, and click Apply to see the maximum
principal stresses on the model.
8. Select any other variables of interest from the Field Output dialog box.
9. From the Invariant option list, select Mises and click OK to display the von Mises stresses again
and to close the dialog box.
Using display groups

You will now create a display group that includes only the element sets that make up the hinge piece that
includes the lubrication hole. By removing all other element sets from the display, you will be able to
view results for the surface of the ßange that contacts the other hinge.
To create the display group:

1. In the Results Tree, expand the Instances container.
C–60
2. From the list of available part instances, select HINGE-HOLE-1. Click mouse button 3, and select
Replace from the menu that appears to replace the current display group with the selected elements.
Click , if necessary, to Þt the model in the viewport.

The contour plot of the entire model is replaced by a plot of only the selected hinge piece, as shown
in Figure C–54.
S, Mises
(Avg: 75%)
+2.576e+07
+2.362e+07
+2.147e+07
+1.933e+07
+1.718e+07
+1.504e+07
+1.290e+07
+1.075e+07
+8.606e+06
+6.462e+06
+4.317e+06
+2.173e+06
+2.824e+04
2
3
1 Step: Load, Apply load
Increment 6: Step Time = 1.000
Primary Var: S, Mises
Deformed Var: U Deformation Scale Factor: +1.000e+02
Figure C–54 Use display groups to view a contour plot of the von
Mises stress in the hinge piece with the lubrication hole.
3. Use the view manipulation tools to view the hinge at different angles. You can now see results for
surfaces on the hinge that were hidden by the solid hinge.
4. From the main menu bar, select Result Field Output.
5. From the top of the Primary Variable tabbed page, toggle on List only variables with results:
and choose at surface nodes from the menu.
6. From the list of variables that appears, select CPRESS, and click Apply.
Abaqus/CAE displays a contour plot of the contact pressures in the ßange hole.
For more information about using the Visualization module, see the following sections:
• “Viewing the results of your analysis,” Section B.11
• Appendix D, “Viewing the Output from Your Analysis”
C–61
You have now completed this tutorial and learned how to:
• create and modify features;
• use datum geometry to add features to a model;
• use position constraints to assemble a model composed of more than one part;
• deÞne contact interactions between regions of a model;
• monitor the progress of an analysis job; and
• use display groups to view results for individual parts of a model.
C.14 Summary
• When you create a part, you can create a deformable part, a discrete rigid surface, or an analytical
rigid surface. You can subsequently change the type of the part.
• You can create parts by adding features to the base feature. When you add a feature, you must
select a face on which to sketch the proÞle of the feature. When you delete a feature from a part,
Abaqus/CAE also deletes any features that depend on the feature being deleted. These dependent
features are called children.
• You can edit features by modifying the sketch of the feature or a parameter associated with the
feature, such as an extrusion depth. Editing features can cause dependent features to fail during
regeneration.
• The Datum toolset allows you to create datum points, axes, and planes. Datum geometry that you
create on a part can also be used by the Sketcher. For example, if a suitable sketch plane does not
exist, you can use the Datum toolset to create one.
• Click OK in a dialog box to perform the selected operation and to close the dialog box; click Apply
to leave the dialog box open while performing the selected operation. Click Cancel to close the
dialog box without performing an operation.
• You can use the tools in the View Manipulation toolbar to change the view of the model to a more
convenient one. Use mouse button 2 to stop any view manipulation. If you rotate or pan the sketch,
use the cycle view manipulation tool to restore the original view.
• You should save the model database at regular intervals.
• When you create a part instance, the default position is based on the sketch of the base feature.
You can ask Abaqus/CAE to offset the new instance along the X-axis so that it does not overlap
any existing instances. A graphic indicates the origin and the orientation of the global coordinate
system in the Assembly module.
• You position part instances relative to each other in the Assembly module using a sequence of
constraint operations.
• Part instances can be dependent or independent.
• You use the step editor to control the time incrementation during the step.
C–62
• You can use managers to display a list of the entities you have deÞned—for example, steps—and
to help you perform repeated operations.
• By default, Abaqus/CAE propagates interactions or prescribed conditions deÞned in one step to all
subsequent steps.
• Abaqus/CAE color codes the model to indicate how a region will be meshed. Green indicates that
a region can be meshed with structured methods, yellow indicates that a region can be meshed with
sweep methods, and orange indicates that a region cannot be meshed.
• You use the Partition toolset to divide the model into regions that Abaqus/CAE can mesh.
• When you create and name a job, Abaqus/CAE uses the same name for the input Þle it generates.
Consequently, all Þles associated with the analysis (for example, the output database, the message
Þle, and the status Þle) use the same name.
• You can view the progression of a degree of freedom over the course of an analysis that you have
chosen to monitor before submitting the job.
• When you Þrst open an output database, Abaqus/CAE displays an undeformed plot of the model.
• You use display groups to display selected regions of your model. A display group can be composed
of any combination of selected part instances, geometry (cells, faces, or edges), elements, nodes, or
surfaces.
C–63

Getting Started Abaqus Appendix C

Uploaded by

Copyright:

Available Formats

Getting Started Abaqus Appendix C

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Getting Started Abaqus Appendix C

Uploaded by

Copyright:

Available Formats

Appendix C: Abaqus/CAE: AN ADVANCED TUTORIAL

Appendix C: Using Additional Techniques to Create and

Figure C–1 Model used in the hinge tutorial.

• “Meshing the assembly,” Section C.11

C.2 Creating the first hinge piece

Creating the cube

Figure C–2 The base feature (a cube) is created Þrst.

To create the cube:

5. From the Sketcher toolbox, select the rectangle tool .

Adding the flange to the base feature

Figure C–3 The ßange is added to the base feature.

To add the flange to the base feature:

Select this edge

Figure C–5 Use the Sketcher to create the ßange proÞle.

a. From the View Manipulation toolbar, select the magnify tool .

toolbox, select the connected lines tool .

8. ReÞne the sketch by deÞning the following constraints and dimension:

Figure C–6 Draw the rectangular portion of the ßange.

Figure C–7 Add the curved portion of the ßange.

Figure C–8 Final sketch.

Figure C–9 Completed ßange sketch showing the extrusion direction.

manipulation tool again to resize the part to Þt in the viewport.

Creating the sketch plane

There are three operations involved in creating the datum plane:

To create the sketch plane:

Figure C–13 Create a datum axis deÞned by two datum points.

Sketching the lubrication hole

To create the datum point at the center of the lubrication hole:

Figure C–14 Create a datum plane normal to the datum axis.

datum point indicates

3. From the list of methods, click Enter parameter.

Figure C–16 Select the second edge.

To sketch the lubrication hole:

4. From the Sketcher toolbox, select the circle tool .

Figure C–18 Select the face to which to extrude.

Figure C–19 Isometric view of the Þrst hinge.

C.3 Assigning section properties to the hinge part

To define the material:

To define the section:

a. Name the section SolidSection.

Assigning the section

To assign the section to the hinge part:

C.4 Creating and modifying a second hinge piece

Copying the hinge

To copy the hinge:

Modifying the copy of the hinge

To modify the copy of the hinge:

Select datum point

Figure C–20 Delete the datum point and its children.

C.5 Creating the pin

Creating the pin

To create the pin:

Assigning the rigid body reference point

Figure C–22 Create a rigid body reference point on the pin.

To assign the reference point:

C.6 Assembling the model

Creating instances of your parts

To create an instance of the hinge piece with the lubrication hole:

Creating an instance of the solid hinge piece

To create an instance of the solid hinge piece: