CCNP - BSCN Cram Session (By Brain Buzz)

TM
BrainBuzz
Cramsession
Last updated October, 2000.

Click here for updates.
Click here to see additional
documents related to this study
Cramsession™ for
guide. Building Scalable
Cisco Networks
Contents Routing 2.0
Contents .............................. 1
Routing Protocols .................. 2 Abstract:
Hybrid Protocols .................... 3 This Cramsession will help you to
Link State Protocols ..............10 prepare for Cisco exam 640-503,
Building Scalable Cisco Networks Routing
TCP/IP ................................15 2.0. Exam topics include: The Advanced
Encapsulation Protocols .........17 Fundamentals for Implementing,
Planning and Configuring a Scalable
Routed v. Routing Protocols ...17 Cisco Network such as TCP/IP, WAN,
Network Services and Gateways LAN, Routing Protocols, Interface
..........................................18 Configuration, and Networking.
BGP ....................................20
Notice: While every precaution has been taken in the preparation of this material, neither the author nor BrainBuzz.com
assumes any liability in the event of loss or damage directly or indirectly caused by any inaccuracies or incompleteness of
the material contained in this document. The information in this document is provided and distributed “as-is”, without any
expressed or implied warranty. Your use of the information in this document is solely at your own risk, and Brainbuzz.com
cannot be held liable for any damages incurred through the use of this material. The use of product names in this work is
for information purposes only, and does not constitute an endorsement by, or affiliation with BrainBuzz.com. Product
names used in this work may be registered trademarks of their manufacturers. This document is protected under US and
international copyright laws and is intended for individual, personal use only. For more details, visit our legal page.
© 2000 All Rights Reserved – BrainBuzz.com
BrainBuzz Cramsession: Building Scalable Cisco Networks Routing 2.0 2
Routing Protocols
Classfull Routing Protocols RIP and IGRP
Link state protocols support classfull addressing as well, but for exam purposes,
consider them primarily used in a classless infrastructure. RIP and IGRP do not pass
subnet information.
RIP
Route Metric HOPS and ticks. The max hop count is 16. Used in small diameter
networks, does not scale well in a very large enterprise environment. Sends its
entire routing table out to all its interfaces every 30 seconds.
IGRP
Is a more robust than RIP. IGRP is a Cisco-proprietary classfull routing protocol.
IGRP does not support VLSM or discontiguous subnets. IGRP will send its entire
routing table every 90 seconds. Over slow links this can be a problem with the
amount of bandwidth that would be consumed in updates.
More study guides and information available at www.cramsession.brainbuzz.com.

IGRP supports load balancing over paths with unequal bandwidth. The variance
command is used to load balance IGRP.
Router igrp 90
Variance 3
The default variance is 1 for equal balancing. The variance multiplier can go 1-128.
IGRP uses a “keep alive” timer to determine if links are still up. Triggered updates
cause the IGRP router to send a routing table update out if its interfaces. Periodic
updates still get broadcasts sent to connected routers every 90 seconds.
Routing loops
Distance vector protocols use the following to prevent routing loops:
Poison Reverse Split Horizon Holddown Timers
Hybrid Protocols
EIGRP
Considered a hybrid protocol. It combines the best features of both link state and
distance vector. It can detect a link failure within one second. It converges rapidly
and scales well into large networks. EIGRP sends routing updates to directly
connected neighbors; only changes are sent rather than the entire routing table.

Bandwidth is the primary metric. That is why it is important to specify the

bandwidth on an interface. EIRGP has a default for serial interfaces of 1.5Mbps. So
you must set the correct bandwidth with the bandwidth command.
Advantages to EIGRP:
• VLSM Support
• Supports Discontiguous Subnets
• Multi-Protocol Support
• Automatic Route Summarization
• Keeps copy Neighbors Routes
• Load Balances up to 6 Paths
DUAL
Diffusing Update ALgorithm – The routing engine behind EIGRP. It allows for routers
to update at the same time and allows for multi-protocol routing. It tracks route
updates sent by neighbors and ensures against black holes.
EIGRP Discovery Process

EIRGP sends hello packets out of all of its interfaces to find its neighbors.

The new router then exchanges update packets with the adjacent routers. The
adjacent routers then send ACKs to the new router. When this step is completed the
new router will then choose its routes (successors).
Route Summarization for EIGRP

This is on by default, but only at the network or class boundaries. Manual
configuration for route summarization is primarily done at the core or distribution
layers. An example of the syntax for configuration is as follows:
ip summary-address eigrp 100 10.98.0.0 255.255.0.0
Important! By default, EIRGP does not support VLSM. You must use the no auto-
summary command. Summaries are done at the interface level rather than at the
router level. Use no auto-summary command to enable support of discontiguous
subnets.

Example:
router eigrp 100
network 10.0.0.0
network 192.64.0.0
no auto summary
interface serial 1
ip address 10.98.98.24 255.255.255.0
bandwidth 128
ip summary-address eigrp 100 192.64.0.0 255.255.0.0
EIGRP Tables
EIGRP keeps three active tables in its database.
• Topology Table – Is kept for each protocol. It is a table of all the route
entries the router has learned. Syntax: show ip eigrp topology shows the
number of successors, active or passive, and distance to destination.
• Neighbor Table – EIGRP keeps a table for each adjacent router and one for
each protocol. Syntax: show ip eigrp neighbors
• Routing Table – Each protocol has its own routing table. EIGRP calculates
the best route, or successor, from the topology table and puts the entry in the
routing table. Syntax: show route eigrp
EIGRP Traffic
You can use the show ip eigrp traffic to view traffic statistics. This includes hello
packets, updates, ACKs and replies.
EIGRP Configuration

Default routes
You can also configure the route to forward to a default network if a route is not
found in the routers routing table. Use the following syntax:
router(config)#ip default-network 10.98.98.1
Static routes
Can be used between two AS’s or in a DDR situation. You define specific routes
between the AS’s so you do not have to spend bandwidth on routing updates.
router(config)# ip route 10.98.8.0 255.255.255.0 172.16.32.0 e0 permanent
10.98.8.0 255.255.255.0 is the destination
172.16.32.0 is the next hop address.
Passive interface
You can configure EIGRP with a passive interface, which will not allow it send any
routing updates including hello packets. Use the following syntax:
router(config-router)#passive-interface e0
Route filters
It is also possible to filter out inbound and outbound routing updates.
Outgoing Syntax:
router(config-router)# distribute-list 101 out e0 static
101= the access-list-number
out = filters for outbound
e0 = the interface
static = name of route process
Incoming Syntax:
router(config-router)# distribute-list 101 in e0
in = filters for inbound
e0 = the interface
Route Redistribution with EIGRP and IGRP

Routes can be redistributed within routing protocols. With EIGRP and IGRP this
process is automatic if the AS systems numbers are the same. If the numbers are
not the same then the redistribution will have to be done manually with the default-
metric command:

router(config-router)# redistribute protocol X metric Y

router(config-router)#default-metric bandwidth delay reliability loading mtu
Route Redistribution with EIGRP and OSPF

Determine the core routing protocol.
Locate the router or ASBR where the route distribution needs to take be configured.
Make the decision of which is your short term or edge protocol.
Determine the route process where you want the route distributed.
Example: router(config)# router ospf X
X= the process id
Use the redistribute command to populate from the short term or edge protocol to
the core routing protocol.
Example: router(config-router)# redistribute protocol X metric Y
X= the process id and Y = the metric value
router(config-router)# redistribute ospf 213 metric 110 subnets
router(config-router)#default-metric X
X= the metric value wanted
Define the seed metric to be used in the calculation of the value of the route before
distribution.
For EIGRP
Router(config-router)# default-metric bandwidth delay reliability loading mtu
Administrative Distance
Advertised Distance
Advertised Distance is the distance a neighbor router says, or advertises, is the
distance to a destination. This is key in electing a feasible successor or backup
route. The lower the distance, the better. The lower the value the better the route
is believable. These values can be changed with the distance command.

Administrative Distances
Protocols
Distance Value
Connected Interface 0
Static routes 1
EIGRP Summary
5
routes
EBGP 20
Internal BGP 90
IGRP 100
OSPF 110
RIP 120
EGP 140
External IEGRP 170
Internal BGP 200
EIGRP and Dropped Links

When EIGRP discovers a down link the router does a lookup in its topology table for
a successor. If a suitable one is found, it changes to the new route. The router then
does a recalculation for the next successor. If one is not found, the router begins a
new process.
The failed route or link is moved into active status and sends query packets to its
adjacent neighbors. It multicasts out to every interface except the one it was
learned from.
The router then waits for a response. If the adjacent router does not have a route to
the destination, nor has a feasible successor, it sends a unicast packet back to the
troubled querying router. If the neighbor router is using the troubled query router as
a successor, it sends its own query packet to its neighbors. This query will
propagate the entire AS.
If the troubled query router receives a successor, or feasible successor, the data is
changed in the topology table and the router waits to receive more responses. The
routing table is recalculated and the route is returned to passive state.
If no route updates for a successor or feasible successor are found, then the router
deletes the entry from the topology database and routing table. If routers do not
respond within 180 seconds their routes are also put into active state, and the query
router begins to look for the additional routes it lost though the lost router.

EIGRP and NBMA

Take particular care when configuring EIGRP in a NBMA environment.
Three NBMA Scenarios:
• Pure point-to-point configuration – each PVC on subinterfaces
• Multi-point configuration – no subinterfaces
• Hybrid (mixed) multi-point and point-to-point
In these scenarios it is important that:

• The traffic bandwidth given to EIGRP on each VC must be the same in both
directions;
• The total EIGRP traffic for the sum of all the VC’s must not exceed the line
speed of the interface; and
• The EIGRP traffic allowed on one VC must not exceed the capacity of the VC.
Link State Protocols

OSPF (Open Shortest Path First)
Is a link state routing protocol that uses Dijkstra’s algorithm for route calculation.
OSFP has several advantages:
• VLSM Support
• Fast Convergence
• No Hop Count Limit
• Route Selection Based on Cost
• Low Bandwidth Usage
OSPF Commands (Single Area) Setup

router (config)#router ospf # (#=process ID)
• Enables ospf on the router
router (config-router)#network address wildcard-mask area # (#=area id)
• Address can be a subnet, network or the address of the interface
• Selects the networks that will be in the OSPF network
router (config-if)#interface loopback #(#=the loopback address)
• OSPF has been proven more reliable with a loopback number
• Loopback address can override the highest ip address for the router id

router (config-if)#ip ospf priority 0-255

router (config-if)#ip ospf cost # (#= the cost value 1-65535)
Cost values Ethernet=10, T1=128, 56k serial=1785
OSPF in a Single Area
Once the loading phase is completed and the router is ready to join the OSPF
network, the router is in Full State.

Routers exchange hello packets every 10 seconds to verify links are up. The Dead
interval is 4X the hello interval.
SPF hold time - Is the time the router waits before doing a SPF route calculation.
The default hold time is 10 seconds.
Neighbor relationships will vary with the connection types. Different OSPF
configurations are required for each.
NBMA - Non-Broadcast Manual Configuration needed. Static lists for routes must be
created.
Router must poll for the routing information since broadcasts are not allowed. Use
the neighbor command to accomplish this.
neighbor ip-address X Y [X=priority #] [Y=poll-interval]

OSPF Multiple-Areas Configuration Commands Enable OSPF on

the Router
router(config)# router ospf X (X=process id)
• Next step is to tell the router which networks are on the OSPF network
router(config-router)#network address wildcard-mask area (area id)
LSA1 – Router Links LSA – Sends information about the routers links.
LSA2 – Network Link LSA – Sent by the DR to all routers in the AS. A list of routers
in the segment.
LSA3 – Summary Link LSA – Sent by ASBR’s list of networks available outside the
area.
LSA4 – Summary Link LSA – Sent by ASBR’s list of networks available outside the
area.
LSA5 – External Link LSA – Sent by ASBR’s list of external network routes.
OSPF recalculates a new table when a route goes down. So, if you have a link
flapping you may want to increase the amount of time to wait. Use spf holdtime
command. If not, it could overload CPU and cause performance issues.
LSA’s are sent and an ACK is expected as a response. If an ACK is not received it
will resend in 5 seconds. This can be changed with the command: ip ospf
retransmit-interval 9 (changes retransmit time to 9 seconds)
Area Types – The area types determine what kind of LSA’s the area will receive.
Stub Area – Does not accept External LSA’s. LSA Type 5’s are rejected. Can except
route summaries.
Totally Stubby Areas – Will not except any LSA’s with external or summaries.

Internal Routers – Exchange LSA’s 1 and LSA’s 2. They share the same routing
database and all interfaces are within the same area.
Backbone Routers BBR – Exchange LSA’s 1 and LSA’s 2. Share at least on

interface in the area 0.
Area Border Router ABR– Share an interface with another OSPF area. This router
keeps a database for each area.
Autonomous System Border Router ASBR – Have at least one interface in a non-
OSPF network. Its uses LSA 5’s to distribute this routing information into the OSPF
network.
Route Table Updates

Routers take Type 1 and Type 2 LSA’s and make their own route calculations. These
entries are used to modify the routing table.
The routers will also take Type 3 and Type 4 LSA’s and use them to calculate a route
for areas in the internetwork. When a router has both an inter-area route and intra-
area route are always kept. An easy way to remember this is, “Why go around the
block to do next door?”
Only stub area routers do not expect type 5 LSA’s. All other routers perform path
calculations to external AS’s.
Commands for Stub Area Configuration

router(config-router)#area area-id stub
• Configures Regular Stub area
router(config-router)#area area-id stub no-summary
• Configures A Total Stub Area

Commands for Route Summarization on OSPF

For ASBR’s:
router(config-router)#summary-address address mask
• Condenses inter-area routes into summary
For ABR’s:
router(config-router)#area area-id range address mask
• Condenses inter-area routes into summary
Commands for Troubleshooting OSPF

router#show ip route
• Gives the route information learned by the router.
router#show ip protocol
• Router information along with metrics and networks. Used to verify how
OSPF is configured.
router#show ip ospf
• Displays how many times the SPF algorithm was calculated and update
interval time.
router#show ip ospf interface
• Displays hello interval, adjacencies, and the ospf area id.
router#show ip ospf neighbor detail
• Shows the list of neighbors, DR and BDR info priorities and states.
router#show ip ospf database
• Displays the database topology, link state database, router id and ospf
process id.
router#show ip ospf border-routers
• List the ABR’s in the AS.
router#show ip ospf virtual-links
• Shows the status on all the virtual links.
TCP/IP
TCP/IP is a widely used routable protocol, and its biggest challenge is proper
management of addressing, security and broadcast management.
Private Addressing
The usual address prefixes are 10, 172 and 192. Used for private networks not
openly exposed to the Internet (inside a firewall).

Public Addressing
Assigned by an ISP, not recommended for private networks. Private to public
network communication can be accomplished by NAT through a PIX or other
firewalls. Options also include VPN (Virtual Private Networks) or extranets secured
through PPTP (Point-To-Point-Tunneling-Protocol) and/or L2TP (Layer 2 Tunneling
Protocol).
Hierarchical Addressing
Using an address scheme where the different network numbers determine whether a
destination is local or remote. Longer subnet masks are used at the access layers.
Network prefix gets smaller as you move up the network hierarchy.
Prefix Routing
This is how a router forwards packets. Router uses the network number to make
routing determination.
Classfull Addressing
This addressing scheme is commonly used where the subnet mask reflects the
number of bits used to calculate the default gateway (e.g. Class A 10.0.0.0 mask
255.X.0.0, Class B 172.0.0.0 255.255.0.0, Class C 192.0.0.0 255.255.255.0). RIP
and IGRP can only be used with a classfull addressing scheme.
Classless Addressing
CIDR - Classless Inter-Domain Routing - is used to conserve and use address space
effectively (see VLSM). This is required for route summarization to work correctly.
Careful planning and implementation are required. An easy way to identify a
classless address is to look at the subnet mask. You will commonly see a Class A
address with a Class B or C subnet mask. Some protocols require additional
configuration to support discontiguous subnets. Link state protocols support
classless addressing. RIP and IGRP do not, because they do not pass subnet
information.
VLSM
Variable Length Subnet Mask - classless addressing allows using, for example, a
Class B address with a Class C subnet mask. Usually summarized in this fashion
172.98.98.24/30. “30”, or 255.255.255.252, specifies the number of bits used to
calculate the network portion. This allows effective use of your IP addresses and
should only be used with routing protocols that support VLSM, like IEGRP and OSPF.

Secondary Addressing
Is assigning a second IP gateway address for the same interface on a router. This is
not recommended as a good practice and should be used only when you have to.
Encapsulation Protocols
Authentication
CHAP or PAP - CHAP is encrypted; with PAP login and password information are sent
in plain text.
GRE
Generic Routing Encapsulation – Used primarily in the backbone. Can be used to
tunnel IPX or AppleTalk. Fast switching supported.
NWLINK
Used to encapsulate NetBIOS over IPX. Requires type 20 packets to operate
properly. Use the ipx type-20-propogation commands on the interface.
NBT
Used to encapsulate NEBIOS over TCP/IP.
AURP
AppleTalk Update Routing Protocol – Encapsulated in TCP/IP over WAN links. Sends
updates only like EIGRP.
Routed v. Routing Protocols

It is important to distinguish the difference between routed and routing protocols.
Routing protocols use metrics, hop counts, ticks, etc. to make a routing decision.
Since routers do not forward broadcasts, routers separate networks into different
broadcast domains. Switches and bridges separate media into separate collision
domains. Routers are responsible for:
• Switching and/or relaying packets
• Path determination
IPX on the WAN

Use NLSP for faster convergence over IPX/RIP and reduced routing traffic. It uses
cost as calculation metric and is more CPU intensive. NLSP redistributes RIP but
retains 15-hop limit. NLSP supports up to 1023 hops.

EIGRP for IPX

Increases bandwidth by only sending updates over the WAN and full updates over
the LAN. When a route goes from IPX/RIP to EIGRP it increases the hop count by
two. From EIRGP to IPX/RIP, the route tick count is unchanged.
AppleTalk
RTMP
AppleTalk’s’ version of a routing protocol. Very similar to RIP broadcasts entire table
in 10 Seconds. Max Hop count is still 15, uses split horizon.
Design Rule
Uses EIRGP for routing AppleTalk.
EIGRP
Saves bandwidth because only updates are sent. Fast convergence.
Network Services and Gateways

DHCP
BOOTP server used to assign IP addresses to requesting clients. Can be configured
to specify node type, WINS, DNS and other information.
There are several options for DHCP configuration. Cisco offers IOS features to
forward DHCP packets. *ip helper-address command forwards broadcasts to DHCP
servers like an NT server.
WINS
Windows Internet Name Service – is a static addressed server that performs
NetBIOS-name-to-IP-address resolution. It resolves NetBIOS names to IP
addresses, which takes away the need to ARP (broadcast) to resolve network names.
After booting and obtaining a DHCP IP address, the client sends a unicast packet to
the WINS server requesting to register its NetBIOS name. DNS servers and WINS
servers (sometimes on the same server) work together to resolve name lookup. Acts
as a register for windows machines.
DNS
Application server that provides Internet-name-to-IP-address conversion. Windows
DNS servers can be directed to query a WINS server for NetBIOS names.

Helper Addressing Syntax

ip helper-address X.X.X.X (where X.X.X.X is the destination IP)
no ip helper-address X.X.X.X (where X.X.X.X is the destination IP) to remove.
Multiple ports and servers can be configured:

int e1
ip address 10.98.98.24 255.255.255.0
ip helper-address 172.98.65.2
ip forward protocol 69
ip helper-address 192.54.12.8
ip forward protocol 2020
NAT
Network Address Translation
Can be used to merge two large networks without having to re-address the whole
network. Another function of NAT is overloading inside global addresses. This
process allows several inside addresses to use a single IP address. NAT can also use
a pool of addresses or multiple interfaces.

BGP
Border Gateway Protocol
BGP is an EGP (exterior gateway protocol) it is used to pass routing information
between autonomous systems. It is still a routing protocol and, like the other
routing protocols, it passes routing information and uses a metrics for route
determination. It functions to advertise which networks can be reached. BGP can
act as an IBGP or EBGP. Which means it can be configured to advertise networks
within an AS or between different AS’s. The trick to BGP is you have to tell BGP
which networks to advertise whether they are directly connected or not. BGP uses
TCP (port 179) to communicate with other routers.
To avoid having to manually update several routers with a single BGP change you
can use the peer-group command to group router together. This enables you to
implement a common policy, distribute-list, route-maps, and update policies. Use
the following syntax:
#neighbor peer-group-name peer-group

#neighbor ip-address peer-group peer-group-name
Common BGP Implementation

Establishing a connection to ISP. Most of the configuration choices for you will be
made for you by your ISP.

Like OSPF, a BGP-configured router will first exchange the entire routing table. Once
a peer has been established only changes are sent. BGP routers also send
keepalives to make sure connections are still active. Like OSPF and EIGRP, BGP uses
AS numbers. BGP uses a single metric for path selections. The network
administrator manipulates the metric value to achieve the desired result.
BGP Metric Criteria

Speed Delay Cost Stability # of AS’s passed through
Traits of BGP Path Selections

• Use routes with a higher BGP administrative value first
• When routes have identical weights use the route with the higher local
preference
• When routes have identical local preference use the route that the server
originated
• When the next hop is not accessible DO NOT consider it
• When AS paths are the identical length choose the external path over an
internal path
• Use the shorter AS path if no route was originated
• When all routes are external use the route with the lowest origin code
• Use the path with the lowest MULTI_EXIT_DISC metric if the origin codes are
the same and the paths came from the same AS
• Use the route with the lowest ip address value for the BGP router ID
• Use the path through the closest neighbor when IGP is disabled and only
internal paths are left
BGP Commands
Network command - used to tell BGP which network to advertise.
Setting up BGP on a router
1. router bgp AS#
2. network ip-network# mask network-mask
#router bgp 300
#network 131.108.0.0 mask 255.255.0.0
Neighbor command - used to establish the BGP peer. This is used for IBGP and
EBGP. (**Note the difference in the AS number to tell if it is an EBGP configuration
or an IBGP configuration.)

External BGP Configuration:

Establishing EBGP Peer:
1. router bgp AS#
2. network ip-network# mask network-mask
3. neighbor ip-address remote-as AS#
Router Dallas
#router bgp 200
#network 131.108.0.0 mask 255.255.0.0
#neighbor 131.108.32.5 remote as 300
*Note AS numbers are different*
Internal BGP Configuration:

Establishing IBGP Peer:
router bgp AS#
network ip-network# mask network-mask
neighbor ip-address remote-as AS#

Router Austin
#router bgp 200
#network 131.108.0.0 mask 255.255.0.0
#neighbor 131.108.32.4 remote-as 200
*Note AS numbers are the same*
Router Dallas
#router bgp 200
#network 131.108.0.0 mask 255.255.0.0
*Note AS numbers are the same*
The similar AS number on the last line indicates to the BGP router that the neighbor
is an internal BGP neighbor, as opposed to the external configuration, where the BGP
network number and the remote AS were different.

Shutdown command – used to disable a peer.

To stop (disable) the peer relationship to Router Austin:
#neighbor ip-address|peer-group-name shutdown
# neighbor 131.108.32.5 shutdown
No command - to reverse the effect of the command use the no command

#no neighbor ip-address|peer-group-name shutdown
#no neighbor 131.108.32.5 shutdown
Reset Connections Commands

To clear the BGP database, cache or table use the following commands.
****Note they all start with clear ip bgp****
#clear ip bgp ip-address
• To clear a single bgp connection
#clear ip bgp peer-group tag
• To clear all the members of the bgp peer group
#clear ip bgp
• To clear all the bgp connections
#bgp fast-external-failover
• To clear sessions for external peers directly connected use
BGP Control Commands

Route flapping can cause havoc on your BGP configurations. Use the following
commands to control updates sent and enable dampening.
#bgp dampening
• Enables route dampening for BGP
#clear ip bgp dampening address mask
• Use the clear command to reverse dampening
#show ip bgp flap-statistics

• Use the flap-statistic command to show flapping routes
#clear ip bgp flap-statistics
• Use the clear command to clear the statistics

BGP Statistic Commands

#show ip bgp summary
• Use the summary command to display the status of all BGP connections
#show ip bgp paths
• Use the path command to view the BGP database
#show ip bgp neighbors address
• Use the show neighbors commands to a detailed list of the bgp neighbors
and the TCP information
BGP Path Filtering by Neighbor

You can path filter by configuring an access list and applying that access list using
the as-path command. BGP filtering is done with the filter-list command. ****
Note that filtering by neighbor uses the as-path command with expressions (and
filter-list) and route filtering uses the distribute list command. Both use access
list****
Use the following syntax to filter by neighbor.
*Note: an access list must be configured first!
#ip as-path access-list access-list-number# permit|deny as-expression

Example:
#router bgp 200
#network 131.108.0.0 mask 255.255.0.0
#neighbor 131.108.32.5 remote- as 300
#neighbor 131.108.32.5 filter-list 1 out
#ip as-path access-list 1 permit ^$
^$= AS-expression
BGP Route Filtering

This syntax will filter by route filter by neighbor. This configuration uses access list
and the distribute list command.
*Note: an access list must be configured first!
#access-list access-list# permit|deny source source-mask
Use the following syntax:
#neighbor ip-address distribute list assess-list# in|out

For Example:
Router Dallas
#router bgp 200
#network 131.108.0.0 mask 255.255.0.0
#neighbor 131.108.32.4 remote-as 300 distribute-list 1 out
Backdoor Routes
Routes that you do not want advertised but used by a border router are called
backdoor routes. To enable a backdoor route use the following command.
#network address backdoor
BGP Summary Routes

Use the aggregate-address command to summarize network routes.
Syntax:
#aggregate-address address mask
or
#aggregate-address address mask summary-only
There are more variations of this command.
Distributing Network 0.0.0.0 into BGP

To allow the distribution of network 0.0.0.0. Which is not allowed by default. Use
the following syntax:
#default-information originate
BGP Route Distribution

Static Routes BGP – Is one method of dealing with flapping networks and preventing
BGP instability. The drawback with static routes is BGP will show the route to be
active even if the route is down. Static routing with BGP enables the route to always
be advertised and always in the routing database. Use the redistribute static
command. Use the following syntax to distribute static routes.
#router bgp 100
#neighbor 131.108.0.0 mask 255.255.0.0
#redistribute static
ip route 10.0.0.0 0.255.255.255 null 0

null 0 is a null interface. With the configuration above it will cause any packet
destined for the 10.x.x.x to be discarded.
Default Route (Gateway)
0.0.0.0 is the default gateway. It is also the gateway of last resort. It is easier
implement this to an interface on the your border router going to your
ISP. Use the following syntax:
#ip route 0.0.0.0 0.0.0.0 s1
Dynamic Route Distribution

To distribute IGP routing information use the redistribute protocol process-id
command. See the earlier notes in the EIRGP route distribution section.
To prevent any routes from being advertised to BGP use the passive-interface
command.
Route Filters
Route Maps – used by BGP to control which routes are advertised between routing
domains. They typically used in a community and are used for filtering. The map-
tag command refers to the name of the route map.
Syntax:
#route-map map-tag permit|deny sequence#
BGP Communities
BGP routers can be grouped into logical groups knows as communities.
Route Reflectors
As you can tell by the multiple BGP commands and options, configuration for BGP
can get quite cumbersome (not to mention making sure all the routes have been
configured correctly). External AS’s make this problem even more cumbersome. To
help reduce the amount of peers a router will have in an AS, there are route
reflectors. The routers peer with another router, or concentration router. These

peers are then known as Clients. They receive updates from and send updates to
the route reflector.
In an BGP AS, there can be several routers 40+ exchanging route information. To
reduce the amount of peers a router has to establish, a concentration and or route
reflector router can be configured. Reflect clients are configured to exchange
information with a central concentration router (route reflector). So reflect clients
only peer with the central concentration route instead of every router in the AS. The
central router (route reflector) is responsible for sending updates to the reflector
clients. The reflector clients are responsible for sending updates to the central
concentration router instead of every router in the AS.
Syntax for Route Reflection:

#neighbor ip-address route-reflector-client
disables client to client reflection
#no bgp client-to-client reflection
Confederations (route reflection on steroids)

A confederation is a large single autonomous system split into smaller sub-
autonomous systems. The other networks see the confederation as a single AS. The
sub AS’s are transparent to the outside world. The advantage to this is the same as
route reflection: it reduced the number of peers IBGP.
Syntax for BGP Confederation for Router Z:

#router bgp 275
#bgp confederation identifier 300

#bgp confederation peers 250 300 350

Modifying Parameters and Administrative Distances for BGP
How to apply route maps to the routing table:

#table-map route-map name
Changing administrative distances:

BGP uses three administrative distances local, external and internal.
#distance bgp external-distance internal-distance local-distance
The default timer is 60 seconds for keep-alives. BGP sends out periodic keepalives
to make sure routes are still up. If the route is down then the holddown timer is
used before declaring the route dead.
To adjust the time, use the following syntax: #timers bgp keepalive holdtime
• This changes the times for all bgp peers.
Special Thanks to Julian Laredo for contributing material for this

Cramsession.


CCNP - BSCN Cram Session (By Brain Buzz)

Uploaded by

Copyright:

Available Formats

CCNP - BSCN Cram Session (By Brain Buzz)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CCNP - BSCN Cram Session (By Brain Buzz)

Uploaded by

Copyright:

Available Formats

TM

Last updated October, 2000.

More study guides and information available at www.cramsession.brainbuzz.com.

Poison Reverse Split Horizon Holddown Timers

More study guides and information available at www.cramsession.brainbuzz.com.

Bandwidth is the primary metric. That is why it is important to specify the

EIGRP Discovery Process

More study guides and information available at www.cramsession.brainbuzz.com.

Route Summarization for EIGRP

ip summary-address eigrp 100 10.98.0.0 255.255.0.0

More study guides and information available at www.cramsession.brainbuzz.com.

More study guides and information available at www.cramsession.brainbuzz.com.

Route Redistribution with EIGRP and IGRP

More study guides and information available at www.cramsession.brainbuzz.com.

router(config-router)# redistribute protocol X metric Y

Route Redistribution with EIGRP and OSPF

More study guides and information available at www.cramsession.brainbuzz.com.

EIGRP and Dropped Links

More study guides and information available at www.cramsession.brainbuzz.com.

EIGRP and NBMA

In these scenarios it is important that:

Link State Protocols

OSPF Commands (Single Area) Setup

More study guides and information available at www.cramsession.brainbuzz.com.

router (config-if)#ip ospf priority 0-255

OSPF in a Single Area

More study guides and information available at www.cramsession.brainbuzz.com.

More study guides and information available at www.cramsession.brainbuzz.com.

OSPF Multiple-Areas Configuration Commands Enable OSPF on

More study guides and information available at www.cramsession.brainbuzz.com.

Backbone Routers BBR – Exchange LSA’s 1 and LSA’s 2. Share at least on

Route Table Updates

Commands for Stub Area Configuration

More study guides and information available at www.cramsession.brainbuzz.com.

Commands for Route Summarization on OSPF

Commands for Troubleshooting OSPF

More study guides and information available at www.cramsession.brainbuzz.com.

More study guides and information available at www.cramsession.brainbuzz.com.

Routed v. Routing Protocols

IPX on the WAN

More study guides and information available at www.cramsession.brainbuzz.com.

EIGRP for IPX

Network Services and Gateways

More study guides and information available at www.cramsession.brainbuzz.com.

Helper Addressing Syntax

Multiple ports and servers can be configured:

More study guides and information available at www.cramsession.brainbuzz.com.

#neighbor peer-group-name peer-group

Common BGP Implementation

More study guides and information available at www.cramsession.brainbuzz.com.

BGP Metric Criteria

Traits of BGP Path Selections

More study guides and information available at www.cramsession.brainbuzz.com.

External BGP Configuration:

Internal BGP Configuration:

More study guides and information available at www.cramsession.brainbuzz.com.

More study guides and information available at www.cramsession.brainbuzz.com.

Shutdown command – used to disable a peer.

No command - to reverse the effect of the command use the no command