PEOPLE Factsheet

PRACTICES

SYSTEMS
Basics of HVAC Energy Efficiency

HVAC System Components Figure 1: HVAC System Schematic

(NDY Management Pty Ltd)
A typical Heating, Ventilation and Air Conditioning (HVAC) system
consists of plant equipment (chillers, boilers etc.) which transfer
energy via air, water or a refrigerant to air distribution systems
consisting of a series of fans and coils. These distribution systems
are usually called air handling units (AHUs). The AHUs then use
this energy to warm or cool the air that is supplied to the office
space.

Air is warmed or cooled as it flows over the heating or cooling

coils in the air distribution system. Heat rejection is also required
at this point, to reject excess heat collected from the space, to
the atmosphere. Heat rejection can also occur through plant
equipment such as cooling towers or evaporative coolers.

The main thermal loads in a commercial building are a

combination of:
` heat produced by people
` heat generated by computers and equipment
` solar radiation through windows
` heat conduction through walls, windows and roof
` heat generated by lighting. Energy Efficiency Opportunities in HVAC
To provide comfortable indoor conditions, an amount of fresh Figure 2 shows the typical energy consumption breakdown in
outdoor air must be supplied to the building. The quantity is an office building, with HVAC systems consuming the greatest
proportional to the number of people in the space. Air from portion (39%)1. A further breakdown of the typical energy
outside is usually warmer in summer and cooler in winter than consumption associated with these HVAC system components
the desired indoor conditions; hence this air must be conditioned. is shown in Figure 3.
Conditioning this fresh air increases the load on the system.
For further information regarding HVAC energy consumption
Generally, air is transported through ductwork while water and please see the HVAC Energy Breakdown Factsheet on the Heating
refrigerants are distributed through pipework. The entire process Ventilation and Air Conditioning High Efficiency Systems Strategy
is energy intensive - the main users of this energy being the HVAC (HVAC HESS) website2.
plant, fans and pumps. Pumps and fans require energy in the
form of electricity to distribute water and air through the building.
Chillers and boilers can run on either electricity or gas.

Figure 1 shows the schematics of a HVAC system and the

interactions between plant, medium, systems and loads.

All systems in a building are linked via a Building Management

System (BMS), which monitors the systems and provides a
point at which issues can be diagnosed, and systems tuned
and optimised.

1 Lecamwasam, L. (2012) Wilson, J. (2012) Chokolich, D. (2012). Guide to Best Practice Maintenance & Operation of HVAC Systems for Energy Efficiency.
Department of Climate Change and Energy Efficiency, p 36-37.
2 http://ee.ret.gov.au/

HVAC HESS Heating, Ventilation & Air-Conditioning High Efficiency Systems Strategy September 2013 1
 Basics of HVAC Energy Efficiency

Figure 2: Typical Energy Consumption in an Office Building3 1. Reduce Loads Within Space

9% ` Reduce Equipment Load – Reducing usage of heat-producing

1%
4% HVAC equipment such as computers, printers and lights will reduce
39%
Lighting the need for HVAC systems to condition a space. Simple
things such as turning off monitors, computers or lights when
Equipment they are not in use will reduce conditioning loads.
22%
Lifts ` Improvements to Façade (Walls) – Increasing the insulating
properties of the building fabric will generally decrease the
Domestic Hot Water amount of cooling or heating required, and hence reduce
Other overall energy usage.
` Improvements to Façade (Windows) – Window loads occur
25%
in the form of solar radiation and conduction. Solar radiation
Figure 3: Typical Energy Consumption of HVAC Systems3 refers to the heat created as direct sunlight comes through a
window and hits a solid surface in an internal space absorbing
160 the electromagnetic radiation. Conduction refers to the
34% movement of heat from the hotter side of the window to the
140
cooler side. Shading devices minimise the solar load from the
120 windows and reduce loads in the space. A typical double-
27%
glazed window will conduct significantly less heat into a room
100 than a typical single glazed window. Another aspect to be
MJ/m2

considered is air sealing, a lack of which can lead to increased

80 17%
16% conditioning requirements.
60
For further information see the Revolving Doors Factsheet2.
40
6% ` Demand Based Ventilation – Conditioning fresh air requires
20 considerable energy as it is often at a significantly different
temperature to that desired in the space. A minimum quantity
0
of fresh air is required in a space based on occupancy in
Fans Cooling Heating Pumps Cooling
Towers accordance with Australian Standards. Carbon dioxide (CO2)
sensors can be used to determine the minimum amount of
fresh air required and lower the fresh air supplied, saving
It is important to reduce overall energy use and increase
energy.
energy efficiency, while delivering a comfortable environment.
Optimum comfort for sedentary work is between 20°C and 26°C, 2. Improve HVAC System Efficiency
depending on the time of the year and clothing worn4. Generally
the temperature in office buildings should vary according to the ` System Selection – Significant energy savings can be realised
outside temperature and should be changed month to month. through optimal system selection. For example, a Variable Air
Volume (VAV) AHU regulates the volume of the supply air to
In order to maintain a comfortable temperature and humidity the spaces depending on the amount of heating or cooling
level within a building, the HVAC system must overcome all of required. This system allows for greater control and reduces
the different loads in the building that work against the desired airflow rates, which reduces overall fan energy consumption.
conditions. The methods to improve energy efficiency in a This greater control may also reduce energy wastage
building’s HVAC system can be broken down into two categories: associated with re-heating, where the heating system
counteracts the cooling system.
1. reduction of the loads within a space that the HVAC system
has to overcome For further information see the Air Handling Unit Factsheet2.
2. improve efficiency of HVAC equipment and systems. ` Plant Selection – Plant selection can greatly affect the overall
energy consumption of a building. For example, condensing
boilers - used for the provision of heating hot water - can have
gross efficiencies over 90%.

3 Guide to Best Practice Maintenance and Operation of HVAC Systems for Energy Efficiency (January 2012).
http://ee.ret.gov.au/energy-efficiency/non-residential-buildings/heating-ventilation-and-air-conditioning-hvac
4 WorkSafe Victoria, Compliance Code for Workplace Amenities and Work Environment, 2008

HVAC HESS Heating, Ventilation & Air-Conditioning High Efficiency Systems Strategy September 2013 2
Basics of HVAC Energy Efficiency

 Evaporative pads can be used on air cooled chillers to HVAC HESS

pre-cool air prior to reaching chiller condensers, improving
efficiency. Accurate plant sizing also has a large impact on HVAC HESS is a ten year strategy under the National Strategy
energy efficiency. Chillers generally work most efficiently on Energy Efficiency that aims to drive long term improvements
at a particular load, so they should be sized to operate at in energy efficiency of HVAC systems Australia-wide. Under
or near this load most of the time. the Energy Efficiency Working Group, the Buildings Committee
manages the implementation of the HVAC Strategy. This
For further information see the Boiler Efficiency and Chiller
committee is comprised of representatives from Australian,
Efficiency Factsheets2.
State and Territory Governments.
` Building Tuning and Commissioning – Energy savings can be
The Strategy takes a whole of life perspective in targeting HVAC
achieved through the commissioning and tuning process.
efficiency improvement, encompassing the design, manufacture,
After a HVAC system has been installed, commissioning and
installation, operation and maintenance stages of the HVAC
on-going tuning of the system will allow the system to function
lifecycle. The Strategy consists of a number of complementary
as per the original design intent, optimise its operation and
measures that fall under three broad initiatives – People, Practices
obtain maximum energy savings.
and Systems. This Basics of HVAC Energy Efficiency factsheet
For further information see the Commissioning and Building relates to all three categories. It is one of a suite of factsheets
Tuning and Coil Cleaning Factsheets2. developed to provide a quick overview and reference to inform,
` Energy Recovery – Energy recovery involves capturing waste educate, and encourage energy efficiency in the HVAC industry.
energy and recycling it. Exhaust air is generally closer to the A series of HVAC HESS factsheets can be found at:
desired space temperature than the outside fresh air being http://ee.ret.gov.au/
introduced into the system. Heat or ‘coolth’ can be drawn
from the exhaust air and used to pre-warm or cool the fresh
air entering the system prior to it reaching the AHU. This
Acknowledgements
lowers the energy used by the AHU to condition the fresh air. The Buildings Committee wishes to thank Norman Disney & Young
For further information see the Heat Pump and Heat Recovery for their valued contribution to this factsheet.
Factsheet2.

` Smart Control Strategies – There are many examples of smart

control strategies achieved through optimisation of the BMS
and building information available to it. One option is to install
smart control software that allows the BMS to determine
optimum operating conditions for the entire HVAC system to
achieve the lowest energy consumption. To achieve this it is
important to optimise consumption information for separate
parts of the HVAC system. This can be achieved through
installation of sub-metering and sensing.
For further information see the Wireless Metering and Building
Management Systems Factsheets2.

` Economy Cycle – Economy cycle involves using 100% outdoor

air to supply air to the space. This occurs at times of the year
when the outdoor conditions are cooler than the return air
temperature in cooling mode. This allows the plant to turn off
the cooling coils and reduces chiller energy consumption.
For further information see the Retrofit of 4 Mort St Canberra
Case Study2.

HVAC HESS Heating, Ventilation & Air-Conditioning High Efficiency Systems Strategy September 2013 3