Penta

Installation, Operation
and Programming

Electronics Line (E.L.) Ltd.

www.elecline.com
ELECTRONICS LINE’S TECHNICAL SUPPORT DEPARTMENT
INTERNATIONAL: (972)-3-9211110 USA: 1-800-683-6835

ZI0094C (2/99)
2
 TABLE OF CONTENTS

Introduction......................................................................................................... 4
About the Penta Installation, Operation and Programming Manual ..........................4
Publication Information .............................................................................................4
Chapter One: Overview ...................................................................................... 4
1.1: Specifications ....................................................................................................4
1.2: Zones ................................................................................................................5
1.3: Telephone Communication................................................................................5
1.4: Remote Programming.......................................................................................6
Chapter Two: Installation .................................................................................... 7
2.1: Parts and Options..............................................................................................7
2.2: Fuse Replacement ............................................................................................7
2.3: Wiring Diagram .................................................................................................8
2.4: Terminal Connections........................................................................................9
2.5: Mounting the Keypad.......................................................................................10
2.6: Turning on the System.....................................................................................11
Chapter Three: System Operation..................................................................... 12
3.1: General............................................................................................................12
3.2: Keypad Layout ................................................................................................12
3.4: Arming/Disarming............................................................................................13
3.6: Distress Keys...................................................................................................14
3.7: User Codes .....................................................................................................15
3.8: Zone Bypassing/Unbypassing .........................................................................16
3.9: Event Logs ......................................................................................................16
3.10: Additional Operations ....................................................................................17
Chapter Four: Programming ............................................................................. 18
4.1: General............................................................................................................18
4.2: Guide to Programming ....................................................................................18
4.3: Programming Parameters...............................................................................19
4.4: Periodic Test Timer Reset...............................................................................23
Appendix A: Hexadecimal Conversion Chart..................................................... 24
Appendix B: Glossary of Terms ........................................................................ 25
Index ................................................................................................................ 28

3
INTRODUCTION

About the Penta Installation, Operation and Programming Manual

This manual is designed to help you with the installation process for the Penta control
panel. We strongly urge you to read through this manual, in its entirety, before beginning
the installation process so that you can best understand all that this security system has
to offer your customers. This manual is not intended for end user use. End users are
encouraged to read the manual accompanying the system, the Penta User Manual. If you
have any questions concerning any of the procedures described in this manual please
contact Electronics Line at (972)-3-9211110 (International) or 1-800-683-6835 (USA).

Publication Information
Catalog Number: ZI0094C (2/99)

CHAPTER ONE: OVERVIEW

1.1: Specifications
Power Input Secondary: 15-16.5Vac, 22-30VA transformer
Battery backup: 12Vdc/3.2Ah
Power Output Auxiliary power: 13.6 - 14.0V (AC operated)
12.0V Nominal (Battery operated)
Bell/siren output: 13.6 - 14.0V (AC operated)
12.0V Nominal (Battery operated)
600mA available for peripheral devices.
The bell/siren output must be supervised by a 2.2K ¼W resistor.
Zones 4 security zones supervised by 2.2K ¼W end of line resistors.
1 tamper/ ON/OFF keyswitch zone
Keypads Up to 3 individually addressed.
Current draw - 100mA max. for each keypad, 200mA max. if
three keypads are installed.
3 user initiated distress keys
User Codes 6 (1 master code, 3 standard user codes, 1 duress code and
1 installer code.
Number of digits per user code – 4
Operating 0° to 50°C
Temperature
Dimensions 260 x 237 x 83mm

4
1.2: Zones
The Penta control panel includes four security zones plus one tamper zone which can be
defined for use with an ON/OFF keyswitch. The four security zones are fully pro-
grammable and supervised by end of line resistors. The Penta offers five zone response
types for customized programming to suit a wide range of installations. Each zone can be
programmed to activate a siren/bell when tripped or to generate a silent alarm where only
a message is sent to the central station. The following is a summary of the operational
characteristics for each zone response type:
Perimeter Zone
Perimeter zones instantly generate an alarm when opened.
Suggested Use: Magnetic contacts or detectors protecting the doors and windows which
are never used to enter the premises.
Perimeter Zone With Delay
This zone type starts the entry delay when opened, allowing the user time to disarm the
system.
Suggested Use: Magnetic contacts or detectors protecting the doors commonly used to
enter or leave the premises.
Conditional Zone
If a perimeter zone with delay is opened first, conditional zones do not generate an alarm
when opened during the entry delay. If a conditional zone is opened first, an alarm is
generated instantly.
Suggested Use: Detectors protecting the area in which a keypad has been installed or the
area crossed in order to reach the keypad.
Interior Zone
Interior zones are automatically bypassed when the system is armed using the ‘Stay’
command Q, 9.
Suggested Use: Detectors protecting the interior areas in which the user requires
unrestricted movement when ‘Stay’ arming. For example bedrooms, bathrooms and
interior offices.
24hr Zone
24hr zones always generate an alarm when opened whether the system is armed or
disarmed.
Suggested Use: Panic buttons, glassbreak detectors and areas which require 24 hour
protection.

1.3: Telephone Communication

The Penta allows for up to two telephone numbers (primary and backup) to be
programmed into the system dedicated to central station communications or for use with
the ‘Follow-me’ format. An additional number can be programmed for use in conjunction
with the RP callback feature. Up to 16 digits can be programmed for each telephone
number. The Penta offers a number of communication options and supports either pulse
or DTMF dialing. If after five attempts the panel does not succeed to communicate, the
panel dials the backup telephone number. If communication is unsuccessful, the panel
will attempt to communicate every half hour until communication is established.

5
Central Station Communication
The Penta uses a standard 20pps 4/2 no parity protocol for central station
communication. All events can be programmed to transmit a two digit event code
message to the central station. These codes are usually assigned by the central station -
consult the central station operator for a listing of the different event codes.
Follow-me
The ‘Follow-me’ feature informs the user that an event has occurred by dialing the user’s
telephone number and sounding two beeps. After hearing the two beeps, pressing 3, 6, 9
or # on the phone sounds a number of tones to indicate exactly which type of alarm has
occurred. The number of tones indicates the type of alarm generated.
1 tone = Alarm from zone 1 1 long = F key alarm
2 tones = Alarm from zone 2 tone
3 tones = Alarm from zone 3 2 long = E or P key alarms, zone
4 tones = Alarm from zone 4 tones or keypad tamper
After the alarm tones have been sounded, pressing 3, 6, 9 or # on the phone either
causes the panel to hang up or, if additional alarms have occurred, sound another set of
alarm tones. Note: Electronics Line recommends using a telephone unit with
Continuous DTMF mode. If only Burst mode is available it may be necessary to
press more than once. If using the Follow-me feature, program the relevant event
codes (addresses 11 – 18) with any value greater than 00.

1.4: Remote Programming

Electronics Line’s remote programming software enables programming and operation
from a PC. The software provides a comprehensive interface to the Penta control panel,
facilitating and cutting down the time taken in programming the system. RP access is
gained using a four digit code programmed at address 57. Without this code all remote
programming and operation is restricted.
Answering Machine Override
Answering machine override enables the control panel to distinguish between regular
incoming calls and a communication attempt by the RP (remote programmer) software.
An RP call is identified by the control panel as a sequence of two calls within a 30-second
time window.
1. The control panel does not answer the first incoming call.
2. The control panel opens a 30-second time window from the moment the telephone
stops ringing.
3. The control panel answers after 1 ring and RP communication is established.
This method enables the panel to share the same telephone line with answering
machines and fax machines.
RP Callback
RP call back is a toll-saver feature that makes remote programming more cost-effective.
When the remote programmer contacts the panel, the panel hangs up and calls the
telephone number programmed at address 56.

6
 CHAPTER TWO: INSTALLATION

2.1: Parts and Options

Penta Household Burglary Alarm Control Panel 1
LED Keypad 1
2.2KΩ ¼W resistors 5
6 x ¼ mounting screws 4
Mounting studs 4
PCB support 1
Installation, Operation, and Programming Manual 1
User Manual 1

Optional Parts List

Additional Penta LED Keypad
‘Remote Programmer’ Up/Downloading Software
12Vdc Adapter for Remote Programmer

2.2: Fuse Replacement

The layout of the three protection fuses is as follows

F1: The Battery protection fuse protects the battery

charger circuit. To replace this fuse use a 1.6A/250V
fuse.
F2: The AC protection fuse protects terminals 1 and 2.
To replace this fuse use a 1.6A/250V fuse.
F3: The AUX protection fuse protects the auxiliary power
output to the keypad (terminals 3 and 4). To replace
this fuse use a 1.0A/250V fuse.
F4: The Bell Power protection fuse protects the active
F1 F2 F3 F4 bell output (terminals 7 and 8). To replace this fuse
use a 1.0A/250V fuse.

7
2.3: Wiring Diagram

12V/3.2Ah BATTERY:
Electronics Line (E.L.) Ltd. - Penta
Household Burglary Alarm Panel
Replace the battery every
+ 3 - 5 years.
JPD Jumper Electronics Line (E.L.) recommends testing the system at least
- The maximum charging
for factory once a week. Refer to the testing procedure found in the user
current is 350mA.
default restore manual.

PROTECTION FUSES: AUX OUTPUT CURRENT DRAW:

F1 (BATT): 1.6A/250V The auxiliary output current allowed for peripheral units must
F2 (AC): 1.6A/250V not exceed 300mA when one keypad is installed. For each
F3 (AUX): 1.0A/250V additional keypad (up to 3 max.) the permitted current draw
R B F4 (Bell): 1.0A/250V is reduced by 50mA.
E L
D A
AUXILIARY POWER OUTPUT: BELL/SIREN OUTPUT: Label Part Number:
C 600mA available for
AC Operated: 13.6 - 14.0V ML0024C (2/99)
K Battery Operated: 12V Nominal security applications.
F1 F2 F3 F4

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

AC Transformer + -
AUX KPD Optional
50/60Hz K2 K1 Tamper Earth
+ - Zone
15-16.5Vac Connection
22-30VA
Do not connect to Z1 Z2 Z3 Z4
PGM
a switch controlled ZONE
receptacle. CONNECTIONS
Telephone Line
Connections
Typical End
of Line
Resistor OBSERVE PROPER
N.C. N.C.
Zone WIRING CONNECTIONS
Connections (Refer to the Installation and
2.2K 2.2K (EOLR) Operation Manual for
1
LED Keypad /4 W 1/4W further information)
2.4: Terminal Connections
15-16.5Vac Input
Terminals 1 & 2: Connect a 15-16.5Vac transformer rated at 22-30VA, using 18 AWG
wire.
Auxiliary Power Output
Terminals 3(+), 4(-): The auxiliary power output connections supply power to keypads
and peripheral units such as detectors and other powered sensors.
Keypad Data Bus Connections
Terminals 5 & 6: Connect up to three individually addressed LED keypads to terminals
5 (K2), and 6 (K1). Make sure that the wires are connected to the same connections on
the keypad, see 2.5: Mounting the Keypad.
Bell Power Output
Terminals 7(+), 8(-): Connect these terminals to supply power to the bell. The bell
power output supplies AUX power, rated at 600mA max.

PGM Programmable Output

Terminal 9: The PGM output switches to AUX PGM
+
ground when activated, enabling the
connection of additional system status 3 4 5 6 7 8 9
indicators. Connect the PGM output as
shown in the diagram.
LOAD
(100mA max.)
Tamper Zone/Keyswitch Connections
Terminal 10: Connect a tamper switch or ON/OFF keyswitch to terminals 10(+) and 12(-).
Note: If neither the tamper zone nor keyswitch are used, short terminal 10 to 12 and
define this zone as Tamper Zone at Address 01.
Zone Connections
Terminals 11, 12, 13, 14, 15 & 16:
ZONE 1: Terminals 11(+) & 12(-) ZONE 3: Terminals 14(+) & 15(-)
ZONE 2: Terminals 13(+) & 12(-) ZONE 4: Terminals 16(+) & 15(-)

Telephone Line
Terminals 17, 18, 19, 20: The telephone line should be connected (using the
standard Telco wires - minimum 26 AWG) as follows: 17 - Home Tip, 18 - Home Ring,
19 - Telco Tip, and 20 - Telco Ring.

9
2.5: Mounting the Keypad

Configuration
Jumpers

Buzzer
Terminal Tamper
Block Switch

Up to 3 LED keypads can be connected to the Penta control panel. To mount the
keypad:
1. Separate the front and back cover of the keypad by pressing the locking tabs,
situated at the bottom of the keypad, with a small flathead screwdriver.
2. Pull the keypad wires through the opening in the back cover nearest the terminal
block and mount the back cover to the wall.
3. Define the keypad address by configuring jumpers A & B according to the following
diagram.

Jumper Jumper
Installed Removed

A B A B A B

Keypad 1 Keypad 2 Keypad 3

10
4. Connect the keypad to the control panel according to the following diagram.

+ K2 K1

3 4 5 6 CONTROL PANEL

KEYPAD
K1 K2 +

5. Reassemble the front and back cover of the keypad.

2.6: Turning on the System

Once all of the systems components are properly connected to their destination
terminals, the Penta is ready to be turned on. To avoid the risk of electrical shock or
damage to the control panel, make sure that both the AC supply and the battery are
connected properly before plugging in the system. If you experience any difficulties in
applying power to the unit, please contact Electronics Line’s Technical Support
Department. The Penta control panel is supplied with a default program that includes
typical programming data which means that minimum programming is required for
typical installations.
To turn on the system:
1. Install the JPD jumper located at the top of the board.
2. Reapply power and wait for 10 seconds; the keypad beeps to indicate the end of the
10 second period.
3. Disconnect both the AC and battery power supply.
4. Remove the JPD jumper.
5. Reapply power; the default program is restored.

The default settings can be reset at any time by disconnnecting the power supply and
repeating the above procedure.

11
CHAPTER THREE: SYSTEM OPERATION

3.1: General
All operation and programming of the Penta can be performed using any one of the
three LED keypads that can be installed with each system. This section offers a
complete explanation of the keypad functions and of the LED display, incorporating a
summary of command codes used in system operation.

3.2: Keypad Layout

READY

1 2 3 4 Status
Indicators
Zone SYSTEM
Indicators Status
ARMED POWER Indicators

F
Numeric E Distress Keys
Keypad
P

Buzzer

The numeric keypad is used for operation and programming of the system.
Additionally, three distress keys enable the user to send one of three individual distress
signals to the central station - see 3.6: Distress Keys for further information.
LED Display
1 - 4: LEDs 1 - 4 are used to display zone status. The corresponding LED lights up if a
zone is open. If a zone is bypassed the corresponding LED blinks.
READY: The Ready LED lights up to indicate that there are no open zones or tamper
conditions and the system is ready to be armed.
SYSTEM: The System LED blinks to indicate that new events have been recorded in
one of the logs and when displaying additional system information such as
programming mode or bypass mode.
ARMED: The Armed LED lights up to indicate that the system is armed or in
programming mode.
POWER: The Power LED lights up when both AC & battery power are OK, blinks when
the battery is low & AC power is OK, and goes out in the event of AC failure.

12
3.3: Command Codes
Commands are executed by pressing the ‘Q‘ button followed by the corresponding
command number and, in some cases, a valid user code. The following is a summary
of the command codes used in system operation.
Q0 Quick Arm Q5 + (User Code 1) Program User Codes
Q1 + (User Code) Bypass Mode Q6 Zone Chime
Q2 Emergency/Trouble Q7 + (Installer Code) Programming Mode
Event Log
Q3 Zone Alarm Q8 + (User Code) Forced Arming
Event Log
Q4 Bell/LED Test Q9 + (User Code) Stay Arming

3.4: Arming/Disarming
The following section explains the various arming and disarming methods.
Arming
When all zones are secured the system can be armed normally. Arming the system
transmits a message to the central station identifying which user performed the
operation.
To arm the system:
1. Check that all zones are closed; the Ready LED lights up to indicate that the
system is ready to be armed.
2. Enter a valid user code; the keypad beeps until the end of the exit delay.
Forced Arming
Forced arming enables the user to arm the system with open zones. Electronics Line
recommends waiting until all of the zones are secured and the system can be armed
normally. Note: If zones are still not secured after the exit delay has ended, an
alarm will be generated.
To force arm the system:
1. Press Q, 8.
2. Enter a valid user code; the keypad beeps until the end of the exit delay.
Quick Arming
This feature allows the Penta to be armed without a valid user code. Quick arming the
system transmits an “Armed by User 1” message to the central station.
To “Quick” arm the system:
1. Check that all zones are closed; the Ready LED lights up to indicate that the
system is ready to be armed.
2. Press Q, 0; the keypad beeps until the end of the exit delay.

13
Stay Arming
This feature only arms perimeter zones. This allows the user to stay within the
protected area while the system is armed.
To “Stay” arm the system:
1. Check that all zones are closed apart from the interior zones; the Ready LED lights
up to indicate that the system is ready to be armed.
2. Press Q, 9.
3. Enter a valid user code; the keypad beeps until the end of the exit delay.
Immediate Arming
The system can be operated without an entry/exit delay. Pressing Q during the exit
delay or when the system is armed cancels both the exit and entry delay times.
Disarming
The Penta can be disarmed by entering a valid user code during the entry delay. If an
error is made entering the code, press ‘#’ and enter the code again. When the code is
accepted the Armed LED and the pulsed delay tone are turned off. If the correct code is
not entered by the end of the delay time, an alarm will be generated.
Keyswitch Arming/Disarming
The system can be armed and disarmed using an ON/OFF keyswitch. The keyswitch
has two operation modes.
1. Latching - closing the keyswitch arms the system, opening disarms the system.
2. Momentary - opening and closing the keyswitch either arms or disarms the system.

3.6: Distress Keys

In the case of an emergency, 3 types of alarms can be generated by pressing and
holding down the desired distress key for more than 2 seconds. These alarms will send
the relevant distress codes to the central station. The distress keys are as follows:

FIRE: Sounds the fire bell, sends the ‘Fire’ event code to the central
F station (address 17) and registers in the Emergency/Trouble event log.

EMERGENCY: Sends the ‘Emergency’ event code to the central station

E (address 18), sounds the siren (if programmed at address 01) and
registers in the Emergency/Trouble event log.

P POLICE: Sends the ‘Police’ event code to the central station (address 16),
sounds the siren (if programmed at address 01) and registers in
the Emergency/Trouble event log.

14
3.7: User Codes
The Penta is capable of maintaining four user codes, a duress code and an installer
code. Each of these codes are four digits long. Of the four user codes, only User
Code 1 (default 1111) has authorization to modify other user codes and the duress
code. The installer’s code (default 1234) is the only user code which grants access to
the programming parameters and is programmable at address 61.
To program user codes 1-4:
1. Press Q, 5.
2. Enter User Code 1; the Armed and System LEDs flash and the zone LEDs indicate
the programming status of each user code as follows:
OFF: NOT PROGRAMMED
ON: PROGRAMMED
FLASHING: CURRENTLY BEING PROGRAMMED
3. Enter the number of the code to be changed (1-4); the requested zone LED flashes.
4. Enter the new user code; the LED stops flashing.
5. Enter the next code to be changed or press # to exit.
Note: If the new code is identical to an existing user code, an error tone will be
sounded and the new code will not be accepted.
To erase a user code:
1. Press Q, 5.
2. Enter User Code 1.
3. Enter the number of the code to be erased (1-4); the requested zone LED flashes.
4. Enter Q, Q, Q, Q; the LED stops flashing and the code is erased.
5. Enter the next code to be erased or press # to exit.
Note: Do not erase User Code 1! Erasing this code denies the user the ability to
program user codes. If User Code 1 is accidentally erased, reset the default
program as described in 2.6: Turning on the System.
Duress Code
In the event that the user is forced to disarm the system and/or cancel the bell, entering
the duress code will send a silent alarm to the central station.
To program the duress code:
1. Press Q, 5.
2. Enter User Code 1.
3. Press 5; the Ready LED flashes.
4. Enter a new duress code or Q, Q, Q, Q to erase the existing code.
5. Press # to exit.

15
3.8: Zone Bypassing/Unbypassing
The Penta offers the user the ability to bypass zones. When a zone is bypassed, it is
ignored by the system and will not generate an alarm when tripped.
To bypass a zone:
1. Press Q, 1.
2. Enter a valid user code; the System LED flashes and the LEDs of any currently
bypassed zones light up.
3. Enter the number of the zone to be bypassed; the corresponding zone LED lights up.
4. Press # to exit bypass mode; the bypassed zones flash.
To unbypass a zone:
1. Press Q, 1.
2. Enter a valid user code; the System LED flashes and the LEDs of any currently
bypassed zones light up.
3. Enter the number of the zone to be unbypassed; the corresponding zone LED turns off.
4. Press # to exit bypass mode.
Note: Disarming the system automatically unbypasses all bypassed zones.

3.9: Event Logs

The event logs record events that the system has undergone since the last arming. If
any events have been recorded in either event log, the System LED flashes until the
relevant event log has been viewed. In the event that a trouble condition still exists, the
System LED continues to flash until the condition has been remedied.
Emergency/Trouble Event Log
Zone tamper, keypad trouble or any of the three distress key alarms are registered in
the Emergency/Trouble event log.
To view the Emergency/Trouble event log:
1. Press Q, 2; the various trouble conditions are indicated by the zone LEDs.
The following is a summary of the trouble condition that each LED indicates when lit:
1 - Tamper or Keypad Trouble 2 - Alarm from P key
3 - Alarm from F key 4 - Alarm from E key
2. Press # to exit the event log.
Note: The event logs can only be viewed when the system is disarmed.
Zone Alarm Event Log
The Zone Alarm event log displays the zones from which an alarm was generated since
the system was last armed.
To view the Zone Alarm event log:
1. Press Q, 3; an alarm from a specific zone is indicated by the corresponding zone
LED.
2. Press # to exit the event log.
Both logs are automatically reset when the system is next armed.

16
3.10: Additional Operations
Bell Cancel
To cancel the bell:
• Enter a valid user code or turn the keyswitch as if disarming the system.
Bell/LED Test
To perform a bell/LED test:
• Press Q, 4; the siren is sounded and all LEDs on the keypad are lit for a period of
two seconds.
Zone Chime On/Off
The keypad can be set to chime when Perimeter With Delay or Perimeter zones are
opened or closed. This feature only functions when the system is disarmed.
To toggle the zone chime On or Off:
• Press Q, 6 while the system is disarmed.

The keypad will sound a continuous tone to indicate “Zone Chime ON” or a series of
short beeps to indicate “ Zone Chime OFF”.
Keypad Backlight On/Off
To toggle the backlight of any keypad On or Off:
• Press and hold down # for more than 2 seconds.

17
CHAPTER FOUR: PROGRAMMING

4.1: General
The Penta control panel may be programmed using either the LED keypad or
Electronics Line’s Remote Programmer. If using the Remote Programmer, refer to the
instructions provided with the software.

4.2: Guide to Programming

The control panel has 61 parameter addresses allowing precise custom configuration of
the system to suit the user’s needs. The options for each address are listed in section
4.3: Programming Parameters. All of the programming parameters are stored in the
Penta’s non-volatile EEPROM memory which stores the data in the event that power is
disconnected. Before programming directly after installing the system, restore the
default parameters as explained in 2.6: Turning on the System.

To program the system:

1. Make sure the system is disarmed.
2. Press Q, 7.
3. Enter the Installer Code (the default installer code is 1234); the Armed LED lights
up and the System LED flashes.
4. Enter the two-digit parameter number to be programmed; the Ready LED lights up
and the Armed LED turns off.
5. Enter a new value or press # to cancel; if the value has been successfully changed,
the keypad sounds an acknowledge tone to confirm and the Ready LED turns off.
6. Press # to exit programming mode.
Note: The default Installer Code should be changed immediately after installing
the system.

Hexadecimal Data
Some of the programming parameters require a hexadecimal value to be entered. To
enter hexadecimal data, use the following combination of digits for hexadecimal
numbers greater than 9.

Q, 0 = A Q, 1 = B Q, 2 = C Q, 3 = D Q, 4 = E Q, 5 = F

Keypad Programming Tones

The keypad sounds a series of tones to aid programming. These tones offer the
installer status indication during programming. The following is a summary of the
keypad programming tones.
Short Beep = Confirmation of each keystroke
Long Beep = Acknowledgment of a successful entry
Low Beeps = Error, illegal entry
Continuous Beeps = Entry/Exit delay

18
4.3: Programming Parameters
The following section lists the Penta’s programming parameters which are used to
configure the system. For a listing of the default parameters please contact your local
dealer.
Address 01: Miscellaneous
This address offers a number of options regarding the system set-up. Enter 5 digits at
this address according to the following:

First Digit: P and E Key Function

0 - P and E Audible Alarms 0
1 - E Audible Alarm, P Silent Alarm
2 - E Silent Alarm, P Audible Alarm
3 - P and E Silent Alarms
Third Digit: Keyswitch Function
0 - Latching
8 - Momentary
Fourth Digit: Tamper Zone Definition
0 – Arm/Disarm Keyswitch
4 - Tamper Zone
Fifth Digit: Keypads
0 - No Keypads
1 - One Keypad
2 - Two Keypads
3 - Three Keypads

Address 02: Communication Options

This address consists of the various options used in communication and/or remote
programming. Enter five digits according to the following.

First Digit: Dialing

0 - Pulse
1 - DTMF
Second Digit: RP Access Type
0 - Passcode
8 - Callback

Third Digit: RP Access

0 - Disable RP Access
4 - Enable RP Access

Fourth Digit: Handshake

0 - 1400Hz Handshake
2 - 2300Hz Handshake
Fifth Digit: Protocol
0 - 20pps 4/2 No Parity
1 - Follow Me

19
Address 03: Zone 1 Definition
One of five response types can be assigned to zone 1. Each zone type can be
programmed as ‘Silent’ or ‘Audible’. A ‘Silent’ zone will not activate a siren or bell when
the zone is tripped.

00 - Perimeter zone with delay (Silent)

10 - Perimeter zone with delay (Audible)
01 - Perimeter zone (Silent)
11 - Perimeter zone (Audible)
02 - Conditional zone (Silent)
12 - Conditional zone(Audible)
03 - Interior zone (Silent)
13 - Interior zone (Audible)
04 - 24hr zone (Silent)
14 - 24hr zone (Audible)

Address 04: Zone 2 Definition

Same as above for zone 2.
Address 05: Zone 3 Definition
Same as above for zone 3.
Address 06: Zone 4 Definition
Same as above for zone 4.
Address 07: Entry Delay Time
The entry delay timer determines the amount of time the user has to disarm the system
before an alarm is activated. The entry delay is only initiated if the premises are entered
through a zone defined as ‘perimeter with delay’. Enter a hexadecimal value between 1 and
255 seconds at this address using the hexadecimal conversion chart in Appendix A.
Address 08: Exit Delay Time
The amount of time the user has to leave the premises after arming is determined by
the exit delay timer. An open zone will not activate an alarm during this period. Enter a
hexadecimal value between 1 and 255 seconds at this address using the hexadecimal
conversion chart in Appendix A.
Address 09: Bell Cut-Off Time
The bell cut-off is the period of time that the bell or siren will be activated after an alarm
has occurred. Enter a value between 1 and 5 minutes at this address.

20
Address 10: PGM Options
The PGM (Programmable Output) can be used for indication of certain status or trouble
conditions. When the PGM output is activated terminal 9 switches to ground. Choose
the PGM output setting from the following table.

Value Type Activated By Deactivated By

00 PGM Disabled --- ---
01 System Status System Armed System Disarmed
02 System Status Entry/Exit Tone Follower Entry/Exit Tone Follower
04 System Status System in Communication End of Communication
08 System Trouble AC Loss AC Restore
10 System Status Bell Follower Bell Follower

Event Codes
All events can be programmed to transmit a two digit event code message to the
central station. These codes are usually assigned by the central station - consult the
central station operator/owner for a listing of the different event codes. To disable an
event code program the code as 00. To disable communications program all event
codes as 00.
Address 11: Alarm from Zone 1*
Address 12: Alarm from Zone 2*
Address 13: Alarm from Zone 3*
Address 14: Alarm from Zone 4*
Address 15: Alarm from Tamper Zone*
Address 16: [P] Key alarm*
Address 17: [F] Key alarm*
Address 18: [E] Key alarm*
Address 19: Zone 1 Restore
Address 20: Zone 2 Restore
Address 21: Zone 3 Restore
Address 22: Zone 4 Restore
Address 23: Tamper Zone Restore
Address 24: [P] Key alarm restore
Address 25: [F] Key alarm restore

*
When using the Follow-me feature, program these addresses with a value greater than 00.
21
Address 26: [E] Key alarm restore
Address 27: System Armed (User Code 1)
Address 28: System Armed (User Code 2)
Address 29: System Armed (User Code 3)
Address 30: System Armed (User Code 4)
Address 31: System Disarmed (User Code 1)
Address 32: System Disarmed (User Code 2)
Address 33: System Disarmed (User Code 3)
Address 34: System Disarmed (User Code 4)
Address 35: System Disarmed (Duress Code)
Address 36: Low Battery
Address 37: AC Loss
Address 38: Not In Use
Address 39: Keypad Trouble
Address 40: Low Battery Restore
Address 41: AC Loss Restore
Address 42: Not In Use
Address 43: Keypad Trouble Restore
Address 44: Bell Cancel
Address 45: Periodic test
Address 46: Bypass Zone 1
Address 47: Bypass Zone 2
Address 48: Bypass Zone 3
Address 49: Bypass Zone 4
Address 50: Unbypass Zone 1
Address 51: Unbypass Zone 2
Address 52: Unbypass Zone 3
Address 53: Unbypass Zone 4

22
Telephone numbers
Address 54: Primary Telephone Number
The primary telephone number is the first number that is dialed when an event occurs.
A maximum of 16 digits can be entered at this address. To add a two-second pause,
enter B (Q, 1). To switch from pulse to DTMF dialing enter E (Q, 4). These hexadecimal
digits, B and E, are included in the 16 digit total. Press ENTER after the last digit of the
telephone number has been programmed.
Address 55: Backup Telephone Number
The backup telephone number is dialed if the panel fails to communicate with the
primary number after five attempts. The backup telephone number is programmed in
the same way as the primary telephone number (address 54).
Address 56: RP Callback Telephone Number
Remote programming communication can be established using two methods,
passcode and callback (see address 02, second digit). If RP callback is selected the
panel receives a call from the remote programmer, hangs up and calls back using the
telephone number programmed at this address. The RP callback telephone number is
programmed in the same way as the primary telephone number (address 54).
Note: To disable a telephone number, enter the appropriate address and press
ENTER. It is not possible to program a backup number unless a primary number
has been programmed.
Address 57: RP Access Code
This 4-digit code grants access to the remote programmer. Note: Do not enter Hex digits.
Address 58: Account Number
When an event code is sent, the central station receives an account number to identify
the customer. Enter a 4-digit account number at this address.
Address 59: Installer Code
The installer code is a 4-digit code which grants access to programming mode. The
default for this code (1234) should be changed immediately after installing the system.
Note: Do not enter Hex digits.

4.4: Periodic Test Timer Reset

The periodic test event code (address 45) is sent to the central station once every 24
hours. The first transmission of this code is sent 24 hours after power is applied to the
control panel. If a different time is required, control panel can be programmed to send
the event code every 24 hours from the moment the periodic test timer is reset.
To reset the periodic test timer:
1. Press Q, 7 to enter programming mode.
2. Enter the Installer Code; the Armed LED lights up and the System LED flashes.
3. Enter 99; the periodic test timer is reset and the periodic test code is sent to the
central station.
4. Press # to exit programming mode.

23
APPENDIX A: HEXADECIMAL CONVERSION CHART
The following is a decimal to hexadecimal conversion chart to be used as an aid in
programming:

Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex
00 00 32 20 64 40 96 60 128 80 160 A0 192 C0 224 E0
01 01 33 21 65 41 97 61 129 81 161 A1 193 C1 225 E1
02 02 34 22 66 42 98 62 130 82 162 A2 194 C2 226 E2
03 03 35 23 67 43 99 63 131 83 163 A3 195 C3 227 E3
04 04 36 24 68 44 100 64 132 84 164 A4 196 C4 228 E4
05 05 37 25 69 45 101 65 133 85 165 A5 197 C5 229 E5
06 06 38 26 70 46 102 66 134 86 166 A6 198 C6 230 E6
07 07 39 27 71 47 103 67 135 87 167 A7 199 C7 231 E7
08 08 40 28 72 48 104 68 136 88 168 A8 200 C8 232 E8
09 09 41 29 73 49 105 69 137 89 169 A9 201 C9 233 E9
10 0A 42 2A 74 4A 106 6A 138 8A 170 AA 202 CA 234 EA
11 0B 43 2B 75 4B 107 6B 139 8B 171 AB 203 CB 235 EB
12 0C 44 2C 76 4C 108 6C 140 8C 172 AC 204 CC 236 EC
13 0D 45 2D 77 4D 109 6D 141 8D 173 AD 205 CD 237 ED
14 0E 46 2E 78 4E 110 6E 142 8E 174 AE 206 CE 238 EE
15 0F 47 2F 79 4F 111 6F 143 8F 175 AF 207 CF 239 EF
16 10 48 30 80 50 112 70 144 90 176 B0 208 D0 240 F0
17 11 49 31 81 51 113 71 145 91 177 B1 209 D1 241 F1
18 12 50 32 82 52 114 72 146 92 178 B2 210 D2 242 F2
19 13 51 33 83 53 115 73 147 93 179 B3 211 D3 243 F3
20 14 52 34 84 54 116 74 148 94 180 B4 212 D4 244 F4
21 15 53 35 85 55 117 75 149 95 181 B5 213 D5 245 F5
22 16 54 36 86 56 118 76 150 96 182 B6 214 D6 246 F6
23 17 55 37 87 57 119 77 151 97 183 B7 215 D7 247 F7
24 18 56 38 88 58 120 78 152 98 184 B8 216 D8 248 F8
25 19 57 39 89 59 121 79 153 99 185 B9 217 D9 249 F9
26 1A 58 3A 90 5A 122 7A 154 9A 186 BA 218 DA 250 FA
27 1B 59 3B 91 5B 123 7B 155 9B 187 BB 219 DB 251 FB
28 1C 60 3C 92 5C 124 7C 156 9C 188 BC 220 DC 252 FC
29 1D 61 3D 93 5D 125 7D 157 9D 189 BD 221 DD 253 FD
30 1E 62 3E 94 5E 126 7E 158 9E 190 BE 222 DE 254 FE
31 1F 63 3F 95 5F 127 7F 159 9F 191 BF 223 DF 255 FF

24
 APPENDIX B: GLOSSARY OF TERMS
24hr Zone A zone which is always active regardless of whether the system is armed
or disarmed. Opening a 24hr zone always generates an alarm.
A
AC Loss The disruption of AC power. In the event of AC loss, the panel waits five
minutes before sending an event message.0
Answering The method used in RP communication allowing the control panel to
Machine Override share a telephone line with answering machines, fax machines etc.
Armed The state during which the control panel is fully activated. In most cases,
when the system is armed, opening a zone generates an alarm.
Audible Alarm An alarm that sounds the bell/siren.
Auxiliary The Auxiliary Power Output supplies power to all peripheral units
Power Output (keypads, detectors etc.)
B
Backup The telephone number dialed if the panel fails to communicate with the
Telephone Number primary telephone number.
Beep A tone sounded by the keypad. Four different kinds of beep are sounded
for keystroke confirmation, successful entry acknowledge-ment, illegal
entry and exit/entry delay.
Bell Cut-Off The programmable amount of time the bell is sounded when an audible
zone generates an alarm.
Bell/LED Test An operation that checks if the bell/siren and keypad LEDs are functional.
The bell test sounds the bell and lights all the LEDs on the keypad for a
period of two seconds.
Bypassed Zone A zone which is ignored by the system. No alarm is generated from a
bypassed zone even when the system is armed.
C
Callback A toll saver feature which cuts the cost of remote programming. When a
call is received from the remote programmer the panel hangs up and calls
the RP Callback telephone number.
Central Station The monitoring service the panel alerts when an alarm is generated.
Chime see Zone Chime
Conditional Zone A conditional zone does not generate an alarm if opened during the entry
delay.
D
Default Settings The factory programmed parameters designed to facilitate programming.
Delay The exit/entry delay times are programmed to allow the user time to arm
or disarm the system without generating an alarm.
Disarmed When the system is disarmed, only 24hr zones and distress keys are
capable of generating an alarm.

25
 Distress Keys The three distress keys (F, E and P) generate different types of alarm
when pressed and held down for two seconds.
Duress Code Entering the duress code generates a silent alarm to indicate that the
user is being forced to disarm the system or cancel the bell.
E
Entry Delay See Delay
Event Code The two-digit code transmitted to the central station to indicate that an
event has occurred.
Event Log The two event logs record and display events the system has undergone
since the last arming.
Exit Delay See Delay
F
Follow-Me A method of monitoring the system without connecting to a central station
based monitoring service. In the event of an alarm, the panel dials the
follow-me number and sounds a number of tones via the telephone.
Forced Arming Arming before the system is ready. If zones are still open when the exit
delay has expired an alarm will be generated.
I
Immediate Arming Arming the system without an exit/entry delay.
Installer Code The code which grants access to programming mode.
Interior Zone A zone that is not armed during Stay arming
K
Keypad Trouble Condition brought about by improper definition of keypads or if a keypad
has been disconnected.
Keyswitch Peripheral device connected to the tamper zone for arming and disarming
the system by the turn of a key.
L
Latching One of the two keyswitch function modes. A latching keyswitch toggles
the system to arm or disarm by one turn of the key
(On or Off=Arm/Disarm).
Log See Event Log
Low Battery Condition brought about if the voltage supplied to the backup battery
deteriorates to approximately 10.5V or less.
M
Magnetic Contacts Peripheral device mounted on doors incorporating a magnet that closes a
circuit. Opening the door breaks the circuit and opens the zone to
generate an alarm.
Master Code The only user code with the ability to program other user codes.
Momentary One of the two keyswitch function modes. A momentary keyswitch
toggles the system to arm or disarm by turning the key on and off.
(On & Off=Arm or Disarm).

26
 P
Perimeter Zone Perimeter zones are armed during both regular and Stay arming and can
be defined with or without an exit delay.
Periodic Test The periodic test event code is sent to the central station every 24 hours
to indicate that the system is functional.
PGM Output Programmable output for connecting additional system status indicators.
Primary The first telephone number dialed when an event occurs. Five attempts
Telephone Number are made to establish communication with the Primary telephone number
before dialimg the backup telephone number.
Q
Quick Arming Arming the system without the need for a valid user code.
R
Ready The state in which all zones are closed and the system is ready to be
armed.
Remote The software developed by Electronics Line used for programming the
Programmer system using a PC from a remote location or on-site.
Restore The restoral of a trouble condition to its normal state. For example, if AC
power is reconnected, an AC Loss Restore event code is sent to the
central station.
RP Abbreviation of Remote Programmer
RP Access Code The code that grants access to the remote programmer. The RP Access
Code prevents the system being sabotaged using unauthorized remote
programming.
S
Silent Alarm An alarm that does not activate the bell/siren when generated.
Stay Arming Arming the perimeter of the system while allowing free movement in the
interior zones.
T
Tamper Zone The fifth zone which can be connected to a tamper switch protecting the
control panel by generating an alarm when the metal housing is opened.
Alternately, the tamper zone can be defined for use with an On/Off
keyswitch.
Tone See Beep
U
Unbypass The restoral of a bypassed zone to its original state.
User Code A code that grants access to certain operational capabilities such as
arming and disarming the system.
Z
Zone The physical and logical connection of detection devices to the control
panel.
Zone Chime The tone sounded by a keypad on opening a perimeter zone when the
system is disarmed.

27
INDEX
24hr zone ........................................20 EEPROM.........................................18
24hr Zone ..........................................5 Emergency Key................................14
AC Protection Fuse............................7 Entry Delay ......................................20
Account Number ..............................23 Entry/Exit Delay
Additional Operations ......................17 Cancelling................................................ 14
Answering Machine Override..............6 Erasing User Codes .........................15
Armed LED......................................12 Event Codes ....................................21
Arming.............................................13 Event Logs.......................................16
Forced .....................................................13 Exit Delay ........................................20
Immediate ................................................14 F Key...............................................14
Keyswitch ................................................14 Fire Key ...........................................14
Quick .......................................................13 Follow-me..........................................5
Stay..........................................................14 General Description................................... 6
Audible Zone ...................................20 Forced Arming .................................13
Backlight..........................................17 Fuse Replacement .............................7
Backup Telephone Number..........5, 23 Handshake ......................................19
Bell Cut-Off......................................20 Hexadecimal Data............................18
Bell Test ..........................................17 Conversion Chart..................................... 24
Bell/Power Protection Fuse ................7 Immediate Arming ...........................14
Bypassing Installation .........................................7
zones .......................................................16 Installer Code ...................... 15, 18, 23
Bypassing Zones .............................16 Interior Zone .......................... 5, 14, 20
Callback ......................................6, 19 Introduction........................................4
Central Station Communication .....5, 6 JPD Jumper.....................................11
Account Number......................................23
Keypad
Event Code ................................................6
Address Definition ................................... 10
Protocol......................................................6
Backlight On/Off...................................... 17
Codes Command Codes .................................... 13
user..........................................................15 Configuration ........................................... 19
Codes Connections ............................................ 11
Duress .....................................................15 Display..................................................... 12
Installer ....................................................15 Functions................................................. 12
Command Codes.............................13 LED Indicators......................................... 12
Conditional Zone..........................5, 20 Mounting.................................................. 10
Connections.......................................9 Programming Tones................................ 18
Contents ............................................3 Keypad Protection Fuse .....................7
Default Program ..............................11 Keyswitch ........................................19
Delay Keyswitch Arming/Disarming ...........14
Entry ........................................................20 LED Display.....................................12
Exit...........................................................20 Miscellaneous Parameters ...............19
Dialing Options ................................19 Mounting the Keypad ...................9, 10
Dimensions........................................4 ON/OFF Keyswitch ..........................14
Disarming ........................................13 Operating Temperature ......................4
Keyswitch ................................................14 Optional Parts....................................7
Distress Keys...................................14 Options..............................................7
Duress Code....................................15 Overview ...........................................4
E Key......................................... 14, 19 P Key.........................................14, 19
28
Parameter Addresses ......................18 System LED.....................................12
Parameters Tamper Zone ...................................19
programming............................................19 Telephone Communication ................5
Parts Event Codes............................................ 21
List of.........................................................7 Follow-me .................................................. 6
Optional .....................................................7 RP Communication ................................... 6
Perimeter Zone ...................... 5, 17, 20 Telephone Line
Perimeter Zone With Delay ..........5, 20 Connections .............................................. 9
Periodic Test Timer Reset................23 Telephone Numbers.....................5, 23
PGM................................................21 Backup ...................................................... 5
Police Key .......................................14 Telephone Options...........................19
Power Input .......................................4 Terminal Connections ........................9
Power LED ......................................12 Test
Power Output.....................................4 Bell .......................................................... 17
Programmable Output .....................21 Trouble Indication ............................21
Programming...................................18 Turning on the System .....................11
Duress Code............................................15 Unbypassing Zones .........................16
Guide .......................................................18 User Codes..................................4, 15
Parameters ........................................18, 19 Erasing .................................................... 15
User Codes..............................................15 Programming........................................... 15
Protection Fuses................................7 Wiring Diagram .................................8
Publication Information ......................4 Zone Chime .....................................17
Quick Arming...................................13 Zones ................................................4
Ready LED ......................................12 24hr ..................................................... 5, 20
Remote Programming..................6, 19 Audible .................................................... 20
Access Code ...........................................23 Bypassing................................................ 16
Callback Number .....................................23 Conditional........................................... 5, 20
Connections .............................................. 9
Reset
Definition ................................................. 20
Default Settings .......................................11
General Description................................... 5
Event Logs...............................................16
Interior ........................................... 5, 14, 20
Periodic Test Timer .................................23
Perimeter....................................... 5, 17, 20
RP Access Code..............................23 Perimeter with delay .................................. 5
RP Callback............................. 5, 6, 19 Perimeter With Delay .............................. 20
Telephone Number ..................................23 Silent ....................................................... 20
Silent Zone ......................................20 Tamper................................................ 9, 19
Status Indication ..............................21 Unbypassing ........................................... 16
Stay Arming.....................................14

29
 ELECTRONICS LINE (E. L.) LTD. AND ITS SUBSIDIARIES - LIMITED WARRANTY

ELECTRONICS LINE (E. L.) LTD. AND ITS SUBSIDIARIES (EL) warrants its products to be free from
manufacturing defects in materials and workmanship for two years following the date of sale. EL will, within
said period, at its option, repair or replace any product failing to operate correctly without charge to the
original purchaser or user. In case of defect, contact the security professional who installed and maintains
your security system. In order to exercise the warranty, the product must be returned by the user or
purchaser, shipping costs prepaid and insured to EL. After repair or replacement, EL assumes the cost of
returning products under warranty. EL will not be responsible for any dismantling or reinstallation changes.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any
serial numbers have been altered, defaced or removed.
There is no express or implied warranty of merchantability or warranty of fitness for a particular purpose. Any
action for breach of warranty, including but not limited to any implied warranty of merchantability, must be
brought within the six months following the end of the warranty period. In no case shall EL be liable to anyone
for any consequential or incidental damages for breach of this or any other warranty, express or implied, even
if the loss or damage is caused by the EL's own negligence or fault.
In no event shall EL be liable for an amount in excess of EL's original selling price of the product, for any loss
or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the
product. CONSEQUENTLY, EL SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. EL's
warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or
liability shall arise or grow out of EL's rendering of technical advice or service in connection with Buyers order
of the goods furnished hereunder.
This warranty contains the entire warranty. Additionally, this warranty is in lieu of all other
obligations or liabilities on the part of EL. It is the sole warranty and any prior agreements or
representations, whether oral or written, are either merged herein or are expressly canceled. EL
neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to
change, or to assume for it, any other warranty or liability concerning its products.
EL RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following: criminal
tampering, electrical or communications disruption, it is possible for the system to fail to perform as expected.
EL does not represent that the product/system may not be compromised or circumvented; or that the product
or system will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the
product or system will in all cases provide adequate warning or protection. A properly installed and
maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not insurance or a
guarantee that these events will not occur. Therefore, the installer should in turn advise the consumer to take
any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling
police or fire department, in order to mitigate the possibilities of harm and/or damage.
EL is not an insurer of either the property or safety of the user's family or employees, and limits its liability for
any loss or damage including incidental or consequential damages to EL’s original selling price of the product
regardless of the cause of such loss or damage. If the user wishes to protect itself to a greater extent, EL will,
at user's sole cost and expense, obtain an insurance policy to protect the user, supplemental to user's own
policy, at a premium to be determined by EL's insurer upon written notice from user by Certified Mail, Return
Receipt Requested, to EL's home office address, and upon payment of the annual premium cost by user.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability for
ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty
gives you specific legal rights and you may also have other rights which vary from state to state.

30
 Penta - Programming Worksheet
(01) SYSTEM PARAMETERS
P and E Key Function
P and E Audible Alarms - 0 0
____,____,____,____,____
E Audible Alarm, P Silent Alarm - 1
E Silent Alarm, P Audible Alarm - 2
P and E Silent Alarms - 3
Keyswitch Function
Latching - 0
Momentary - 8
Tamper Zone Definition
Arm/Disarm Switch - 0
Tamper Zone- 4
Keypads
No Keypads - 0
One Keypad - 1
Two Keypads - 2
Three Keypads - 3

(02) COMMUNICATION PARAMETERS

Dialing ____,____,____,____,____
Pulse - 0
DTMF - 1
RP Access Type
Access Code - 0
Callback - 8
RP Access
Disable RP Access - 0
Enable RP Access - 4

Handshake
1400Hz Handshake - 0
2300Hz Handshake - 2
Protocol
20 pps 4/2 No Parity - 0
Follow Me - 1

ZONE DEFINITIONS 00 - Perimeter With Delay (Silent)

10 - Perimeter With Delay (Audible)
(03) __,__ Zone 1 (04) __,__ Zone 2 01 - Perimeter (Silent)
11 - Perimeter (Audible)
02 - Conditional (Silent)
12 - Conditional (Audible)
03 - Interior (Silent)
(05) __,__ Zone 3 (06) __,__ Zone 4 13 - Interior (Audible)
04 - 24hr (Silent)
14 - 24hr (Audible)

TIMERS PGM OUTPUT FUNCTION

(07) __,__h Entry Delay (1-255 Sec) (10) __,__ 00 - PGM Disabled
01 - Armed/Disarmed Status
02 - Entry/Exit Tone Follower
(08) __,__h Exit Delay (1-255 Sec)
04 - Communication Status
08 - AC Loss/Restore
(09) __,__h Bell Cut-Off (1-5 Min) 10 – Bell Follower
EVENT CODES
(11) __,__ Alarm from Zone 1 (32) __,__ Disarmed (User 2)
(12) __,__ Alarm from Zone 2 (33) __,__ Disarmed (User 3)
(13) __,__ Alarm from Zone 3 (34) __,__ Disarmed (User 4)
(14) __,__ Alarm from Zone 4 (35) __,__ Disarmed (Duress)
(15) __,__ Tamper Alarm (36) __,__ Low Battery
(16) __,__ [P] Key Alarm (37) __,__ AC Loss
(17) __,__ [F] Key Alarm (39) __,__ Kpd Trouble
(18) __,__ [E] Key Alarm (40) __,__ Low Battery Restore
(19) __,__ Zone 1 Restore (41) __,__ AC Loss Restore
(20) __,__ Zone 2 Restore (43) __,__ Kpd Trouble Restore
(21) __,__ Zone 3 Restore (44) __,__ Bell Cancel
(22) __,__ Zone 4 Restore (45) __,__ Periodic Test
(23) __,__ Tamper Restore (46) __,__ Bypass Zone 1
(24) __,__ [P] Key Restore (47) __,__ Bypass Zone 2
(25) __,__ [F] Key Restore (48) __,__ Bypass Zone 3
(26) __,__ [E] Key Restore (49) __,__ Bypass Zone 4
(27) __,__ Armed (User 1) (50) __,__ Unbypass Zone 1
(28) __,__ Armed (User 2) (51) __,__ Unbypass Zone 2
(29) __,__ Armed (User 3) (52) __,__ Unbypass Zone 3
(30) __,__ Armed (User 4) (53) __,__ Unbypass Zone 4
(31) __,__ Disarmed (User 1)

TELEPHONE NUMBERS
(54) __,__,__,__,__,__,__,__,__,__,__,__,__,__,__,__ Primary
(55) __,__,__,__,__,__,__,__,__,__,__,__,__,__,__,__ Secondary
(56) __,__,__,__,__,__,__,__,__,__,__,__,__,__,__,__ RP Callback
E = switch from pulse to DTMF dialing B = 2 second pause

RP ACCESS CODE ACCOUNT NUMBER

(57) __,__,__,__ (58) __,__,__,__

INSTALLER CODE
(59) __,__,__,__
 Penta – Default Values
(01) SYSTEM PARAMETERS

3 0 0 4 1
____,____,____,____,____
P and E Key Function
P and E Silent Alarms

Keyswitch Function
Latching

Tamper Zone Definition

Tamper Zone

Keypads
One Keypad

(02) COMMUNICATION PARAMETERS

1 0 4 0 0
____,____,____,____,____
Dialing
DTMF
RP Access Type
Access Code
RP Access
Enable RP Access

Handshake
1400Hz Handshake

Protocol
20 pps 4/2 No Parity

ZONE DEFINITIONS
(03 - 06) Default value for all zones: 00 – Perimeter zone with delay (silent)

TIMERS PGM OUTPUT FUNCTION

0 F h Entry Delay
(07) __,__ (15 Sec) 0 0 (PGM Disabled)
(10) __,__
3 C h Exit Delay
(08) __,__ (60 Sec)

0 5 h Bell Cut-Off
(09) __,__ (5 Min)

EVENT CODES
(11 - 53) Default value for all event codes: 00

RP ACCESS CODE ACCOUNT NUMBER

0 5 0 5
(57) __,__,__,__ F F F F
(58) __,__,__,__

INSTALLER CODE
1 2 3 4
(59) __,__,__,__