Torque Flexitallic

Spiral Wound Gasket CG
Class 150 Class 300 Class 400 Class 600

NPS (in.)
Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque
0.5 30 40 30 40 30 40 30 40
0.75 30 40 60 70 60 70 60 70
1 30 40 60 70 60 70 60 70
1.25 30 40 60 70 60 70 60 70
1.5 30 60 100 120 100 120 100 120
2 60 90 60 70 60 70 60 70
2.5 60 110 100 120 100 120 100 120
3 90 120 100 120 100 120 100 120
3.5 60 90 100 120 160 190 170 210
4 70 120 100 140 160 200 190 240
5 100 160 110 160 210 260 280 360
6 130 200 110 160 190 240 260 330
8 180 200 180 260 310 400 400 510
10 170 320 250 290 340 440 500 590
12 240 320 360 420 510 640 500 610
14 300 490 360 420 500 890 680 800
16 310 490 500 590 680 800 800 940
18 500 710 500 680 680 810 1100 1290
20 430 710 500 740 800 940 1100 1290
24 620 1000 800 1030 1500 1750 2000 2340
Class 900 Class 1500 Class 2500

NPS
Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque
0.5 70 120 70 100 50 100
0.75 70 120 70 100 70 100
1 110 190 110 160 110 160
1.25 110 190 135 170 210 250
1.5 170 290 200 250 310 360
2 110 190 130 170 220 250
2.5 170 290 190 250 300 360
3 140 230 265 360 460 500
4 255 420 415 520
5 360 600 585 800
6 300 500 530 680 Not Applicable
8 485 800 845 1100 Use CGI
10 505 800 1565 2000
12 570 850
14 630 940
16 910 1290 Not Applicable
18 1570 2340 Use CGI
20 1745 2570
24 Not Applicable Use CGI
Notes:
Torque Values are in ft.-lbs., and assume Alloy Steel Bolts (A193 B7 w/ 2H Nuts) with oil/graphite lubrication.
(Nut factors used on these charts are within .15 to .19)
Flexitallic does not generally recommend a bolt stress above 60,000 PSI
Torque values limit minimum and maximum gasket seating stresses based upon pressure class and certain operating conditions.(i.e: maximum pressure
ratings for given pressure class,not hydrotest pressure), Extreme operating conditions such as high temperature may reduce bolt yield strength. Caution
should be used in these applications. The above torque values are for general use only. For critical or extreme applications (high temperature/pressure)
consult with Flexitallic engineering.
Flexitallic does not accept responsibility for the misuse of this information.
This Document is the property of Flexitallic, L.P. and is not to be reproduced, transmitted to another, nor used for the purpose of manufacturing of articles
for sale to anyone but Flexitallic, L.P. without Flexitallic's specific written permission.
12/10
Spiral Wound Gasket CGI
Class 150 Class 300 Class 400 Class 600
NPS (in.)
Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque
0.5 30 50 30 40 30 40 30 40
0.75 30 50 60 80 60 80 60 80
1 30 60 60 80 60 80 60 80
1.25 30 60 60 80 60 80 60 80
1.5 30 60 100 140 100 140 100 140
2 60 120 60 80 60 80 60 80
2.5 60 120 100 140 100 140 100 140
3 90 120 100 150 100 150 100 150
3.5 60 120 100 170 160 290 170 290
4 70 120 100 200 160 320 190 320
5 100 200 110 200 210 320 280 490
6 130 200 110 200 190 320 260 460
8 180 200 180 320 310 490 400 700
10 170 320 250 460 360 710 500 800
12 240 320 360 700 510 1000 500 850
14 300 490 360 610 500 870 680 950
16 310 490 500 920 680 1250 800 1210
18 490 710 500 1000 680 1340 1100 1790
20 430 710 500 1000 800 1430 1100 1640
24 620 1000 800 1600 1500 2270 2000 2670
Class 900 Class 1500 Class 2500

NPS
Min Torque Max Torque Min Torque Max Torque Min Torque Max Torque
0.5 70 120 70 100 50 100
0.75 70 120 70 100 63 100
1 110 190 110 160 110 160
1.25 110 190 140 164 210 250
1.5 170 290 200 250 310 360
2 110 190 130 170 220 250
2.5 170 290 190 250 300 360
3 140 230 270 360 460 500
4 260 420 420 520 710 800
5 360 600 590 800 1280 1500
6 300 500 530 680 1870 2200
8 485 800 850 1100 1780 2200
10 505 800 1570 2000 3040 4400
12 560 850 1500 2200 4610 5920
14 630 940 2120 3180
16 910 1290 2940 4400
18 1570 2340 3950 5920
20 1745 2570 5150 7720
24 2945 5140 8340 12500
Notes:
Torque Values are in ft.-lbs., and assume Alloy Steel Bolts (A193 B7 w/ 2H Nuts) with oil/graphite lubrication.
(Nut factors used on these charts are within .15 to .19)
Flexitallic does not generally recommend a bolt stress above 60,000 PSI
Torque values limit minimum and maximum gasket seating stresses based upon pressure class and certain operating conditions.(i.e: maximum pressure
ratings for given pressure class,not hydrotest pressure), Extreme operating conditions such as high temperature may reduce bolt yield strength. Caution
should be used in these applications. The above torque values are for general use only. For critical or extreme applications (high temperature/pressure)
consult with Flexitallic engineering.
Flexitallic does not accept responsibility for the misuse of this information.
This Document is the property of Flexitallic, L.P. and is not to be reproduced, transmitted to another, nor used for the purpose of manufacturing of articles
for sale to anyone but Flexitallic, L.P. without Flexitallic's specific written permission.
12/10

Torque Flexitallic

Uploaded by

Copyright:

Available Formats

Torque Flexitallic

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Torque Flexitallic

Uploaded by

Copyright:

Available Formats

Spiral Wound Gasket CG

Class 150 Class 300 Class 400 Class 600

Class 900 Class 1500 Class 2500

Class 900 Class 1500 Class 2500

You might also like