Jbor-7b6kge R5 en PDF

InRow® RD
Air-Cooled/Fluid-Cooled - 50/60 Hz
ACRD100
ACRD101
ACRD200
ACRD201
ACRD500
ACRD501
ACRD502
Technical Data
American Power Conversion Legal Disclaimer
The information presented in this manual is not warranted by the American Power Conversion Corporation
to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed
operational and site specific development plan. Therefore, American Power Conversion Corporation
assumes no liability for damages, violations of codes, improper installation, system failures, or any other
problems that could arise based on the use of this Publication.
The information contained in this Publication is provided as is and has been prepared solely for the purpose
of evaluating data center design and construction. This Publication has been compiled in good faith by
American Power Conversion Corporation. However, no representation is made or warranty given, either
express or implied, as to the completeness or accuracy of the information this Publication contains.
IN NO EVENT SHALL AMERICAN POWER CONVERSION CORPORATION BE LIABLE FOR

ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL, OR INCIDENTAL
DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
CONTRACT, REVENUE, DATA, INFORMATION, OR BUSINESS INTERRUPTION)
RESULTING FROM, ARISING OUT, OR IN CONNECTION WITH THE USE OF, OR
INABILITY TO USE THIS PUBLICATION OR THE CONTENT, EVEN IF AMERICAN POWER
CONVERSION CORPORATION HAS BEEN EXPRESSLY ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. AMERICAN POWER CONVERSION CORPORATION RESERVES THE
RIGHT TO MAKE CHANGES OR UPDATES WITH RESPECT TO OR IN THE CONTENT OF
THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME WITHOUT NOTICE.
Copyright, intellectual, and all other proprietary rights in the content (including but not limited to software,
audio, video, text, and photographs) rests with American Power Conversion Corporation or its licensors.
All rights in the content not expressly granted herein are reserved. No rights of any kind are licensed or
assigned or shall otherwise pass to persons accessing this information.
This Publication shall not be for resale in whole or in part.

Contents
Overview .......................................................................... 1
Scalable Solution for Critical Environments ................ 2
InRow Advantages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Scalable for High Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hot Aisle Containment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standard Features........................................................... 4
Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Shutdown Input/Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Variable Speed Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bay Kit-InRow RD/NetShelter SX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Counterflow Cooling Coil/Condensate Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Selectable Top or Bottom Piping Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Network Management Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Condensate Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Temperature Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Optional Features............................................................ 5
Cable Water Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power Trough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Data Partition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Height Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Microprocessor Controller ............................................. 6

Microprocessor Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Open Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Display Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
InRow RD Models............................................................ 8
Exterior components: ACRD100 and ACRD200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Interior components (front): ACRD100 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interior components (rear): ACRD100 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Interior components (front): ACRD200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Interior components (rear): ACRD200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Exterior components: ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Interior components (front): ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical panel: ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
User interface panel: ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
InRow RD Technical Data Manual i

Performance Specifications ......................................... 19
Net Cooling Capacity (Air and Glycol Cooled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Net Cooling Capacity (Water Cooled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Performance at Percentage of Fan Speed . . . . . . . . . . . . . . . . . . . . 21

ACRD100 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ACRD200 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ACRD500 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
General Data .................................................................. 24

General Specifications - ACRD200 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fluid-cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Air Cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Altitude Correction Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sound Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Dimensional Data .......................................................... 27

ACRD100 and ACRD200 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
NetShelter SX to VX Height Adapter: ACRD100 and ACRD200 series . . . . . . . . . . . . . . . 29
NetShelter SX to VX Height Adapter: ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NetShelter SX to 48-U SX Height Adapter: ACRD100 and ACRD200 series . . . . . . . . . . . 29
NetShelter SX to 48-U SX Height Adapter: ACRD500 series . . . . . . . . . . . . . . . . . . . . . . . 29
Piping and Mechanical Connections ........................... 30

Refrigeration Piping Diagram (ACRD100 and ACRD500 series) . . . . . . . . . . . . . . . . . . . . 30
Water cooled piping (ACRD200 series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Glycol cooled piping (ACRD200 series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Top piping and power access locations (ACRD100 series and ACRD200 series) . . . . . . 33
Bottom piping and power access locations (ACRD100 series and ACRD200 series) . . . 34
Top piping and power access locations (ACRD500 series) . . . . . . . . . . . . . . . . . . . . . . . . 35
Bottom piping and power access locations (ACRD500 series) . . . . . . . . . . . . . . . . . . . . . 36
Outdoor Heat Exchangers ............................................ 37

Air Cooled Condensers - Mechanical Data (ACRD100 Series) . . . . . . . . . . . . . . . . . . . . . . 37
Air Cooled Condensers Mechanical Data (ACRD500 Series) . . . . . . . . . . . . . . . . . . . . . . . 37
Fluid Coolers - Mechanical Data (ACRD200 Series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ACCD75201 and ACCD75204 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ACCD75202 and ACCD75205 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ACCD75203 and ACCD75206 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ACCD75207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ACCD75208 and ACCD75209 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ACCD75214 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ACCD75215 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ACCD75216, ACCD75218, and ACCD75220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ACCD75217 and ACCD75219 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ACFC75210 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ACFC75255 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ACFC75256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
ACFC75257 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Air-cooled Condenser Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
ii InRow RD Technical Data Manual
Guide Specifications ..................................................... 43
Guidelines for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Room preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Service access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Receiving the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Condensate drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SKU Selection Width Voltage Plug Type
ACRD100 300 mm 208-240V, 60 Hz, 1 Phase Hard wired
ACRD500 600 mm 200-240V, 50/60 Hz, 3 Phase Hard wired
ACRD502 600 mm 380-415V, 50/60 Hz, 3 Phase Hard wired
InRow RD Technical Data Manual iii

Overview
The modular, row-based computer Compliance Approval Accessories
room cooling system offers efficient, • UL Listed • Cable leak detector
predictable, and economical cooling • CE • Baying kit-InRow RD to NetShelter
for a variety of spaces. VX rack
• C-Tick
Critical environmental requirements • C-UL Listed • NetShelter SX 42-U to 48-U height
now reach far beyond the confines of adapters
the traditional data center or com- • NetShelter VX 42-U height adapters
puter room to encompass a larger
• Bridge trough power cable shield
suite of applications, referred to as
• Data cable bridge partition
technology rooms. Critical environ-
ment applications include: • Isolation ball valves (ACRD100
Standard Features series only)
• Computer rooms All series: • Dry cooler
• Telecommunication facilities • Variable-speed fans • Condenser
• Clean rooms • Shutdown input/alarm output
• Power equipment • 2-way/3-way floating point valve
• Medical equipment rooms • Top or bottom piping
• LAN/WAN environments • Network Management Card (NMC)
• Baying kit-InRow RD to
A worldwide network of APC repre- NetShelter® SX rack
sentatives is fully qualified to
• Remote temperature sensor
provide engineering, sales, installa-
tion, and service for our products. • Microprocessor controller
APC warrants all parts for 12 months ACRD100 series and ACRD200
from the date of purchase. Extended series only:
warranties are available. • Insulated cabinet
• Washable filter
Capacities • Condensate management with two
InRow RD units are available in two dual float condensate pumps
sizes (300mm and 600mm) with
• Scroll compressor
nominal capacities ranging from
2-10kW (300mm) and 10-29kW • Hot gas bypass
(600mm). ACRD100 series only:
• Liquid line solenoid valve
Room Air Distribution
Row-based systems are placed in line ACRD500 series only:
with rack enclosures. At least one • Backward inclined impeller
system is used per hot aisle. Air is • Pleated 100-mm (4-in) filter
drawn in through the rear of the sys-
• NPT to BSPT pipe adapters
tem, cooled, and discharged into the
cold aisle, thereby neutralizing the • Condensate management with one
sensible heating effects of the data dual float condensate pump
processing equipment. The InRow • Variable speed reciprocating
RD delivers high volumes of airflow compressor using VFD control
to eliminate hot spots in densely pop- • Pressure equalization solenoid
ulated environments. • Pipe adapters
Configuration
• Air-cooled
• Fluid-cooled
InRow RD Technical Data Manual 1

Scalable Solution for Critical Environments
InRow Advantages
The row-based solution improves energy efficiency and cooling ability in a number of ways. First, the InRow RD draws
air directly from the hot aisle, allowing the InRow RD to take advantage of higher heat transfer efficiency due to higher
temperature differences. It can then discharge room-temperature air directly in front of the servers it is cooling. Placing
the cooling unit in the row enables the unit to operate at higher return and supply air temperature, yielding 100% sensible
capacity. This significantly reduces the need for humidification.
Scalable for High Density

The predictable performance of the row-based architecture makes it well-suited for high density applications. The focus
on heat removal instead of cold air delivery is the key to making this approach scalable. The modular design of the InRow
RD allows it to be easily added in the row as the demand for cooling increases.
The additional benefit of the row-based architecture is the ability to add hot aisle containment. Containing the hot aisle
further reduces any chance of hot and cold air streams mixing. This provides ultimate predictability and allows the cooling
capacity to be matched to the IT heat load.
2 InRow RD Technical Data Manual

Hot Aisle Containment System
Modular ceiling tiles and doors can be used to enclose the hot aisle. This increases the densities that can be handled in a
single rack enclosure by eliminating mixing of hot and cold air streams. This method, called load neutralization, removes
the heat from the hot aisle, cools it, and then returns it to the surrounding room area at or slightly below room temperature.
The warmer return air temperatures that are achieved in this application increase the capacity of the air conditioner.
Use of modular ceiling tiles across a 914.4-mm (3-ft) hot aisle that connects two opposite rack enclosures makes expan-
sion quick and simple. Expansion kits, with the necessary ceiling tile and all baying hardware, can be ordered to increase
the size of the hot aisle by one rack on each side. The end doors can be easily removed and re-attached for expansion.
The enclosed hot aisle prevents any warm return air from mixing with cold supply air. In effect, all surrounding room air
can act as supply air to the system. The hot aisle containment system is beneficial in any environment. It can be deployed
quickly in any controlled space without expensive additions to the infrastructure, such as raised flooring or ductwork.
na2860a
Dimensions are shown in mm (in).

Standard Features
Cabinet Counterflow Cooling Coil/ Condensate Pump
Condensate Pan
ACRD100 and ACRD200 series:
Designed for high sensible heat Two pumps are factory wired and
ratios, the coil is constructed with piped (in parallel) internally to the
copper tubes, raised lance type alu- condensate drain pan. Acting
The frame is constructed of 16 gauge minum fins, and 18 gauge galvanized together, the pumps are capable of
formed steel for maximum strength. steel end plates. Coil headers are pumping 9.8 l/hr (2.6 g/hr) against
The cabinet is serviceable from the equipped with anti-drip shields in the head pressures of up to 50 ft (15.2 m)
front and rear. All exterior panels and event of condensation. The conden- of total run. Of that run, 16 ft (4.9 m)
corner posts on the frame are powder sate pan is thermal formed non- can be vertical lift as measured from
coated for durability and an attractive ferrous material, and is sloped for floor level. Dual floats are included
finish. The front and rear exterior positive drainage to provide higher with the unit. One float is used for
panels are constructed of 18 gauge indoor air quality. condensate pump control, and the
perforated steel with 69.5% open free other float generates a condensate
area. All panels, which include a key Filters pump failure alarm. The InRow RD
latch for safety and security, allow can be set to either continue running
Filtration of conditioned air is
easy access and removal. Insulation in an alarm condition or shut down to
extremely vital to maintaining the
(ACRD100 and ACRD200 series prevent condensate pan overflow.
clean, particle-free environment
only) is 80.1 kg/m3 (5 lb/ft3) density ACRD500 series:
required by electrical equipment. Fil-
and complies with ASTM E84 rating
ters are easily replaceable from the The single condensate pump is fac-
of 25/50.
rear of the unit. The ACRD100 and tory wired and piped internally to the
200 series systems use greater-than condensate drain pan. The pump is
Shutdown Input/Alarm 20% efficiency ASHRAE 52.1, 12.7
Output capable of pumping a maximum of
mm (1/2 in) washable filters that 18 m (60 ft) at 32 l/h (8.45 g/hr),
The unit provides one field connec- meet HF-1 standards for electronics which may include a maximum lift of
tion input for remote shutdown and (MERV 1 per ASHRAE 52.2). The 3.5 m (11.5 ft) as measured from
one field connection alarm output. ACRD500 series system uses a 30% floor level. Dual floats are included
efficient, 102 mm (4 in), deep load- with the unit. One float is used for
Variable Speed Fans ing, pleated filter (MERV 8 per condensate pump control, and the
ASHRAE 52.2, EN779 G4). other float generates a condensate
Each unit is equipped with variable pump failure alarm to prevent
speed fans to allow for varying heat Selectable Top or Bottom condensate pan overflow.
loads. In order to provide uniform Piping Connections
airflow over the cooling coil, the fans Remote Temperature
provide a draw-through air pattern. The unit includes both top and bot- Sensors
The ACRD100 and ACRD200 series tom piping connections. All
units are equipped with six direct ACRD100 and ACRD500 series con- To control the unit based on rack inlet
drive fan modules. These fans are nections utilize Roto-Lok fittings for temperature, remote temperature sen-
easily replaceable while the unit is in ease of installation and service. The sors are provided. The ACRD100
operation. The ACRD500 series is ACRD200 series uses union and ACRD200 series units come
equipped with two backward connectors. equipped with one temperature sen-
inclined, direct drive fans. sor, and the ACRD500 series units
Network Management Card come equipped with three. These
Bay Kit-InRow RD/ sensors measure temperature at a
The Network Management Card point 4 m (13 ft) from the connection
NetShelter SX
(NMC) allows communication with inside the InRow RD unit. These sen-
Baying kits made of 16 gauge steel the Local Area Network (LAN). In sors are used for remote placement in
enable baying the InRow RD to APC addition, the NMC permits multi- the field on an adjacent IT rack.
NetShelter enclosures. level access to monitoring, control,
and event notification features over
the building network.

Optional Features
Cable Water Detector Filters Data Partition
A leak detection cable is placed on Electrical equipment requires clean, Overhead cable distribution between
the floor or subfloor around all possi- particle free air, thus making air fil- adjacent NetShelter racks allows for
ble leak sources. If water or other tration extremely important. As an removal of the InRow RD without
conductive liquids contact the cable optional feature, higher efficiency fil- disrupting overhead cabling.
anywhere along its length, the micro- ters can be purchased for the InRow
processor controller announces the RD units. The ACRD100 and Height Adapters
leak visually, audibly, and across the ACRD200 series units optionally uti-
network. The 6.1-m (20-ft) cable lize an 50.8mm (2in) pleated, deep To match the height of the InRow RD
may be cascaded to make custom loading, 30% ASHRAE 52.1 filter to various rack heights, height adapt-
lengths up to 24.4 m (80 ft). (MERV 8 per ASHRAE 52.2). The ers are available for NetShelter 42-U
ACRD500 series units optionally uti- VX and 48-U SX racks.
Network Cable lize 102mm (4in) pleated, deep
loading, 85% ASHRAE 52.1 filter
Various lengths of network cable are (MERV13 per ASHRAE 52.2).
available to ship with your cooling
system. The network cable is used to Power Trough
interconnect multiple cooling units in
a redundant group, as well as to con- Overhead power distribution between
nect the Network Management Card adjacent NetShelter racks allows for
to your LAN. removal of the InRow RD without
disrupting overhead power cabling.

Microprocessor Controller
 Critical Alarm LED

Status
ESC
Check
 Warning Alarm LED
Log
?
Warning
 Check Log LED
Critical
 Status LED
 Liquid Crystal Display (LCD)
 Menu Selection scroll keys
 Escape key
 Enter key
 Help key
Microprocessor Controller Control Type Logging

The microprocessor controller is The controller utilizes proportional/ The event log keeps a record of all
standard on each unit. The controller integral/derivative (PID), a time- alarms and events. Each event log
provides precision control for the proven precision environmental con- contains a time/date stamp as well as
demanding requirements of the fol- trol method. This allows for custom operating conditions at the time of
lowing environments: tuning of control variables to achieve occurrence. The controller also dis-
• Computer rooms desired system response. plays run time, in hours, for major
components (air filters, fans, and
• Telecommunication facilities
Functions condensate pump, as well as humidi-
• Clean rooms
fier, heater, and compressor for the
• Power equipment • Supply and return air conditions air-cooled unit).
• Medical equipment rooms • Operational mode control
• LAN/WAN environments • Event logging Display Interface
The easy-to-use display interface • Alarms
allows the operator to select options The backlit, four-line by twenty-
• Redundant group control
from the menu-driven interface to character display interface is pass-
• Fan speed adjustment word configurable.
control and monitor the connected air
conditioning system. • Input/output module programming
Open Architecture
The InRow RD protocol is open for
integration with all building manage-
ment systems. Communication
interface on the system can be Mod-
bus RS485 or Ethernet.

Alarms ACRD100 series and ACRD200 ACRD500 series only:
series only: • Compressor drive communication
The microprocessor controller shall • Condensate pan full fault
activate a visible and audible alarm
• Upper fan power supply fault • Compressor drive fault
in the following occurrences:
• Lower fan power supply fault • Compressor drive warning
All series:
• Suction temperature sensor failure • Compressor run hours violation
• Cool Fail • Persistent low suction pressure fault • Condensate pump run hours
• Air filter clogged violation
• Return air sensor fault ACRD200 series only: • Fan run hours violation
• Supply air sensor fault • Condenser fluid valve actuator fault • Supply humidity sensor fault
• Rack temperature sensor fault • Outdoor heat exchanger (OHE) fault • High suction pressure
• High discharge pressure • Factory configuration not completed
• Low suction pressure • Liquid refrigerant sensor failure
• Fan fault
• Water detected
• Condensate pump fault
• Air filter run hours violation
• Group communication fault
• Supply air high temperature
violation
• Return air high temperature
violation
• Filter DP sensor failure
• Suction pressure sensor failure
• Discharge pressure sensor failure
• Persistent high discharge pressure
fault
• Rack inlet temperature high
violation
• External communication fault
• Internal communication fault
• On standby input contact fault
• A-link isolation relay fault
• Excessive compressor cycling

InRow RD Models
Exterior components: ACRD100 and ACRD200 series
na2625a
 Removable rear door  Adjustable leveling feet
 Side panel latch  Display interface
 Removable side panel  Removable front door
 Rear casters (non-swiveling)  Door lock (front and rear)
 Front casters (swiveling)

Interior components (front): ACRD100 series
na2626a
 Electrical control box 1  Compressor

(retractable)
 Electrical control box 2  Front air block panel
 Return air temperature  Evaporator fans (6 total)

sensor
 Condensate pan floats (2  Expansion valve

total)
 Condensate pan  Evaporator coil

Interior components (rear): ACRD100 series
na2627a
 Filter/dryer  Hot gas bypass valve
 Pressure transducer (2 total, located  Liquid line shutoff solenoid

behind air block)
 Filter differential pressure port  Electrical control box 1
 Air filter (2 total)  Power supply unit (bottom)
 Condensate pump (2 total)  Power supply unit (top)
 Electrical control box 2  Service junction box (top entry shown)
 Sight glass

na2633a
 Electrical control box 1 (retractable)  Compressor
 Electrical control box 2  Front air block panel
 Condensate pumps (2 total)  Evaporator fans (6 total)
 Bypass shutoff valve (2-way)  Condensate pan
 Water control actuator  Condensate pan floats (2 total)
 Water regulating valve (3-way )  Expansion valve
 Brazed plate heat exchanger  Evaporator coil

na2635a
 Filter/dryer  Electrical control box 2
 Pressure transducer (2 total, located  Hot gas bypass valve

behind airblock)
 Suction line  Power supply unit (bottom)
 Filter differential pressure port  Power supply unit (top)
 Air filters (2 total)  Service junction box (top entry shown)
 Sight glass

Exterior components: ACRD500 series
na1824a
 Removable rear doors  Casters (all swiveling)
 Side panel lock  Door handle and lock
 Removable side panel  Display interface
 Adjustable leveling feet  Removable front door

na2720b
 Condensate drain pan  Fan (2)
 Thermal expansion valve  Fan guard (2)
 Compressor  Electrical panel
 Variable Frequency Drive (for  Communication and external

compressor) device connectors
 Supply air temperature sensor  Ground wire
 Main circuit breaker

na2723a
Table 1:
 Evaporator coil  Shutoff valves
 Condensate drain pan  Air filters
 Sight glass  Pipe chase
 Filter dryer  Return air temperature sensor
 Condensate pump

Electrical panel: ACRD100 and ACRD200 series
na2664a
 Leak detector port  Building management system (BMS)

RS-485 port
 Remote temperature sensor port  Control RS-485 port
 A-Link ports  Form C and shutdown input
 Reset button  RS-232 console port
 Network port  Outdoor heat exchanger (OHE) input

and output ports (optional connection
for ACRD100 and ACRD101)

Electrical panel: ACRD500 series
 Transformers
 User interface connectors
 Main controller board
 Relay board
 Ground lug
 Main circuit breaker
 Compressor fuse block

(ACRD500, ACRD501)
Compressor circuit breaker
(ACRD502)
 Fan circuit breakers
 Controller circuit breaker

na2724a

User interface panel: ACRD500 series
 Rack inlet temperature sensors 1, 2, 3
 A-Link IN
 A-Link OUT
 Network port
 Console port
 Alarm output, NC (Normally Closed)
 Alarm output, COM (Common)
 Alarm output, NO (Normally Open)
 Supply GND (Ground)
 Supply 12 Vdc (current limit: 20 mA)
 Supply 24 Vdc (current limit: 20 mA)
 Remote shutdown+ (12–30 Vac/Vdc, 24 Vdc @

11 mA)
 Remote shutdown-
 BMS D1 (RXTX+)
 BMS D0 (RXTX–)
 BMS GND
 Supply air temperature sensor (front)
 Supply air humidity sensor (front)
 Display interface
na2009a

Performance Specifications
Net Cooling Capacity (Air and Glycol Cooled)
Return Air Temperature SKU Total Capacity kW (BTU/hr) Sensible Capacity kW (BTU/hr)
ACRD100 8.22 (28,000) 8.04 (27,400)
ACRD101 8.01 (27,200) 7.71 (26,400)
22.2°C DB, 15.5°C WB (72°F DB, 60°F WB) ACRD200 8.22 (28,000) 8.04 (27,400)
ACRD201 8.01 (27,200) 7.71 (26,400)
ACRD500 series 22.8 (78,000) 19.0 (65,000)
ACRD100 8.52 (29,000) 8.52 (29,000)
ACRD101 8.16 (27,900) 8.16 (27,900)
23.9°C DB, 16.2°C WB (75°F DB, 61.1°F WB) ACRD200 8.52 (29,000) 8.52 (29,000)
ACRD201 8.16 (27,900) 8.16 (27,900)
ACRD500 series 25.2 (86,000) 21.7 (74,000)
ACRD100 10.02 (34,000) 9.12 (31,000)
ACRD101 9.72 (33,200) 8.85 (30,200)
ACRD201 9.72 (33,200) 8.85 (30,200)
ACRD500 series N/A N/A
ACRD100 9.36 (32,000) 9.36 (32,000)
ACRD101 8.97 (30,700) 8.97 (30,700)
ACRD201 9.72 (33,200) 8.85 (30,200)
ACRD500 series 26.9 (92,000) 26.9 (92,000)
ACRD100 9.90 (33,800) 9.90 (33,800)
ACRD101 9.69 (33,100) 9.69 (33,100)
ACRD201 9.69 (33,100) 9.69 (33,100)
ACRD500 series 29.0 (99,000) 29.0 (99,000)
ACRD100 10.44 (35,600) 10.44 (35,600)
ACRD101 10.29 (35,200) 10.29 (35,200)
32.2°C DB, 19.0°C WB (90°F DB, 66.2°F WB)1 ACRD200 10.44 (35,600) 10.44 (35,600)
ACRD201 10.29 (35,200) 10.29 (35,200)
ACRD500 series 30.5 (104,000) 30.5 (104,000)
ACRD100 10.62 (36,200) 10.62 (36,200)
ACRD101 10.5 (35,900) 10.5 (35,900)
ACRD201 10.5 (35,900) 10.5 (35,900)
ACRD500 series 33.7 (115,000) 33.7 (115,000)
ACRD100 10.62 (36,200) 10.62 (36,200)
ACRD101 10.5 (35,900) 10.5 (35,900)
ACRD201 10.5 (35,900) 10.5 (35,900)
ACRD500 series 36.9 (126,000) 36.9 (126,000)
ACRD100 10.56 (36,000) 10.56 (36,000)
ACRD101 10.5 (35,900) 10.5 (35,900)
40.6°C DB, 21.6°C WB) (105°F DB, 70.8°F WB4 ACRD200 10.56 (36,000) 10.56 (36,000)
ACRD201 10.5 (35,900) 10.5 (35,900)
ACRD500 series 36.6 (125,000) 36.6 (125,000)
ACRD100 10.6 (36,000) 10.6 (36,000)
ACRD101 10.5 (35,900) 10.5 (35,900)
43.3°C DB, 22.2°C WB) (110°F DB, 72.0°F WB5 ACRD200 10.6 (36,000) 10.6 (36,000)
ACRD201 10.5 (35,900) 10.5 (35,900)
ACRD500 series N/A N/A
Airflow for the ACRD100 and 200 series is 1081 l/s (2290 SCFM) at full evaporating fan speed.
Airflow for the ACRD500 series is 2171 l/s (4600 SCFM) at full evaporating fan speed.
1
Airflow is reduced to 887 l/s (1880 SCFM) at this condition to maintain adequate evaporating temperature.
2Airflow is reduced to 717 l/s (1520 SCFM) at this condition to maintain adequate evaporating temperature.
3
4
Note: Minimum recommended loads: ACRD100 series and ACRD200 series - 2kW (6,831 BTU); ACRD500 series - 10kW (34,152 BTU)
Note: For ACRD100 and ACRD500 series the outdoor air temperature is 35° C (95° F)
Note: For ACRD200 series, a 40% at 0.64 l/s (10gpm), the entering glycol mixture temperature is 40.6° C (105° F)
Note: For ACRD500 series, reduce airflow and cooling capacity specifications by 7% for cooling units run at low input voltage (380 V).

Net Cooling Capacity (Water Cooled)
Return Air Temperature SKU Total Capacity kW (BTU/hr) Sensible Capacity kW (BTU/hr)
ACRD200 9.72 (33,200) 8.94 (30,500)
22.2°C DB, 15.5°C WB (72°F DB, 60°F WB)
ACRD201 9.57 (32,700) 8.79 (30,100)
ACRD200 8.43 (32,200) 8.43 (32,200)
23.9°C DB, 16.2°C WB (75°F DB, 61.1°F WB)
ACRD201 9.30 (31,800) 9.30 (31,800)
ACRD200 11.52 (39,300) 9.90 (33,800)
26.7°C DB, 19.4°C WB (80°F DB, 67.0°F WB)
ACRD201 11.64 (39,800) 9.99 (34,200)
ACRD200 10.38 (35,400) 10.38 (35,400)
26.7°C DB, 17.1°C WB (80°F DB, 62.8°F WB)
ACRD201 10.11 (34,500) 10.11 (34,500)
ACRD200 10.92 (37,300) 10.92 (37,300)
29.4°C DB, 18.1°C WB (85°F DB, 64.6°F WB)
ACRD201 10.98 (37,500) 10.98 (37,500)
ACRD200 11.64 (39,700) 11.64 (39,700)
32.2°C DB, 19.0°C WB (90°F DB, 66.2°F WB)1
ACRD201 11.76 (40,200) 11.76 (40,200)
2
ACRD200 12.00 (41,000) 12.00 (40,900)
35.0°C DB, 19.9°C WB (95°F DB, 67.8°F WB)
ACRD201 12.00 (41,000) 12.00 (41,000)
ACRD200 12.06 (41,200) 12.06 (41,200)
37.8°C DB, 20.7°C WB (100°F DB, 69.3°F WB)3
ACRD201 12.00 (41,000) 12.00 (41,000)
4
ACRD200 12.06 (41,000) 12.00 (41,000)
40.6°C DB, 21.6°C WB) (105°F DB, 70.8°F WB
ACRD201 12.00 (41,000) 12.00 (41,000)
ACRD200 12.06 (41,200) 12.06 (41,200)
43.3°C DB, 22.2°C WB) (110°F DB, 72.0°F WB5
ACRD201 12.06 (41,200) 12.06 (41,200)
Airflow for the ACRD200 series is 1081 l/s (2290 SCFM) at full evaporating fan speed.
1
2
3
Note: Minimum recommended loads: ACRD200 series - 2kW (6,831 BTU)
Note: For ACRD200 series, a 0.64 l/s (10gpm) entering water temperature is 29.4° C (85° F)

Performance at Percentage of Fan Speed
ACRD100 Series
Net Sensible
Voltage/Phase/ L/S Unit Power in Condenser Fan Capacity kW SA Temp °C
% Fan Speed Hz (SCFM) kW Power in kW (BTU/h) (°F)
Return Air Temperature = 29.4° C (85° F)
200-240/1/60 2.57 0.13 4.60 (15,710) 20.8 (69.5)
30 448 (950)
200-240/1/50 2.58 0.13 4.60 (15,710) 20.8 (69.5)
200-240/1/60 2.67 0.18 5.75 (19,637) 20.8 (69.5)
40 562 (1190)
200-240/1/50 2.70 0.20 5.75 (19,637) 20.8 (69.5)
200-240/1/60 2.76 0.23 6.65 (22,711) 20.8 (69.5)
50 947 (1370)
200-240/1/50 2.80 0.25 6.65 (22,711) 20.8 (69.5)
200-240/1/60 2.86 0.28 7.35 (25,102) 20.8 (69.5)
60 717 (1520)
200-240/1/50 2.90 0.29 7.35 (25,102) 20.8 (69.5)
200-240/1/60 2.92 0.32 8.00 (27,321) 20.8 (69.5)
70 779 (1650)
200-240/1/50 2.98 0.35 8.00 (27,321) 20.8 (69.5)
200-240/1/60 3.04 0.38 8.70 (29,712) 20.8 (69.5)
80 850 (1800)
200-240/1/50 3.08 0.40 8.70 (29,712) 20.8 (69.5)
200-240/1/60 3.19 0.47 9.70 (33,127) 20.8 (69.5)
90 944 (2000)
200-240/1/50 3.22 0.49 9.70 (33,127) 20.8 (69.5)
200-240/1/60 3.46 0.50 9.90 (33,810) 21.7 (71.1)
100 1081 (2290)
200-240/1/50 3.50 0.51 9.90 (33,810) 21.9 (71.5)
Return Air Temperature = 35° C (95° F)
200-240/1/60 2.68 0.28 7.55 (25,785) 20.8 (69.5)
30 448 (950)
200-240/1/50 2.70 0.30 7.55 (25,785) 20.8 (69.5)
200-240/1/60 2.80 0.42 9.50 (32,444) 20.8 (69.5)
40 562 (1190)
200-240/1/50 2.81 0.44 9.50 (32,444) 20.8 (69.5)
200-240/1/60 2.89 0.48 10.20 (34,835) 21.8 (71.2)
50 947 (1370)
200-240/1/50 2.91 0.48 9.90 (33,810) 22.2 (71.9)
200-240/1/60 3.00 0.52 10.62 (36,269) 22.6 (72.6)
60 717 (1520)
200-240/1/50 3.01 0.50 10.29 (35,142) 23.1 (73.5)
200-240/1/60 N/A N/A N/A N/A
70 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
80 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
90 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
100 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 2.78 0.47 10.20 (34,835) 21.3 (70.4)
30 448 (950)
200-240/1/50 2.78 0.48 10.00 (34,152) 21.6 (70.9)
200-240/1/60 2.85 0.51 10.56 (36,064) 24.8 (76.6)
40 562 (1190)
200-240/1/50 2.87 0.53 10.55 (36,030) 24.8 (76.6)
200-240/1/60 N/A N/A N/A N/A
50 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
60 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
70 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
80 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
90 N/A
200-240/1/50 N/A N/A N/A N/A
200-240/1/60 N/A N/A N/A N/A
100 N/A
200-240/1/50 N/A N/A N/A N/A

ACRD200 Series
Voltage/Phase/ Net Sensible Capacity
% Fan Speed Hz L/S (SCFM) Unit Power in kW kW (BTU/h) SA Temp °C (°F)
200-240/1/60 2.35 4.60 (15,710) 20.8 (69.5)
30 448 (950)
200-240/1/50 2.25 4.60 (15,710) 20.8 (69.5)
200-240/1/60 2.41 5.76 (19,671) 20.8 (69.5)
40 562 (1190)
200-240/1/50 2.31 5.76 (19,671) 20.8 (69.5)
200-240/1/60 2.47 6.63 (22,643) 20.8 (69.5)
50 947 (1370)
200-240/1/50 2.37 6.63 (22,643) 20.8 (69.5)
200-240/1/60 2.55 7.36 (25,136) 20.8 (69.5)
60 717 (1520)
200-240/1/50 2.45 7.36 (25,136) 20.8 (69.5)
200-240/1/60 2.60 8.00 (27,321) 20.8 (69.5)
70 779 (1650)
200-240/1/50 2.50 8.00 (27,321) 20.8 (69.5)
200-240/1/60 2.68 8.70 (29,712) 20.8 (69.5)
80 850 (1800)
200-240/1/50 2.58 8.70 (29,712) 20.8 (69.5)
200-240/1/60 2.80 9.70 (33,127) 20.8 (69.5)
90 944 (2000)
200-240/1/50 2.70 9.70 (33,127) 20.8 (69.5)
200-240/1/60 3.06 10.90 (37,225) 21.0 (69.8)
100 1081 (2290)
200-240/1/50 3.00 10.98 (37,499) 20.9 (69.7)
200-240/1/60 2.25 7.50 (25,614) 20.8 (69.5)
30 448 (950)
200-240/1/50 2.25 7.50 (25,614) 20.8 (69.5)
200-240/1/60 2.31 9.50 (32.444) 20.8 (69.5)
40 562 (1190)
200-240/1/50 2.31 9.50 (32.444) 20.8 (69.5)
200-240/1/60 2.37 10.50 (35,859) 21.2 (70.)
50 947 (1370)
200-240/1/50 2.37 10.50 (35,859) 21.2 (70.)
200-240/1/60 2.50 11.35 (38,762) 21.8 (71.3)
60 717 (1520)
200-240/1/50 2.45 11.35 (38,762) 21.8 (71.3)
200-240/1/60 2.61 11.75 (40,128) 22.4 (72.4)
70 779 (1650)
200-240/1/50 2.50 11.75 (40,128) 22.4 (72.4)
200-240/1/60 2.71 12.00 (40,982) 23.2 (73.7)
80 850 (1800)
200-240/1/50 2.58 12.00 (40,982) 23.2 (73.7)
200-240/1/60 N/A N/A N/A
90 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 N/A N/A N/A
100 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 2.35 10.55 36,030) 20.8 (69.5)
30 448 (950)
200-240/1/50 2.25 10.55 36,030) 20.8 (69.5)
200-240/1/60 2.40 11.70 (39,958) 22.8 (73.0)
40 562 (1190)
200-240/1/50 2.31 11.70 (39,958) 22.8 (73.0)
200-240/1/60 2.46 12.00 (40,982) 24.8 (76.7)
50 947 (1370)
200-240/1/50 2.37 12.00 (40,982) 24.8 (76.7)
200-240/1/60 N/A N/A N/A
60 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 N/A N/A N/A
70 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 N/A N/A N/A
80 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 N/A N/A N/A
90 N/A
200-240/1/50 N/A N/A N/A
200-240/1/60 N/A N/A N/A
100 N/A
200-240/1/50 N/A N/A N/A

ACRD500 Series
Condenser Net Sensible
Fan Power in Capacity kW
% Fan Speed Voltage L/S (SCFM) Unit Power in kW kW (BTU/h) SA Temp °C (°F)
30 All 700 (1400) 2.03 0.01 7.3 (24,931) 20.8 (69.5)1
40 All 900 (1800) 3.25 0.02 9.8 (33.469) 20.8 (69.5)1
50 All 1100 (2300) 4.28 0.03 12.1 (41,324) 20.8 (69.5)1
60 All 1300 (2800) 6.32 0.06 14.5 (49,520) 20.8 (69.5)
70 All 1500 (3200) 7.12 0.07 16.9 (57.717) 20.8 (69.5)
80 All 1700 (3700) 9.13 0.10 19.4 (66,254) 20.8 (69.5)
90 All 2000 (4100) 9.52 0.18 21.8 (74,451) 20.8 (69.5)
100 All 2200 (4600) 11.74 0.31 24.2 (82,647) 20.8 (69.5)
30 All 700 (1400) 4.28 0.05 11.95 (40,811) 20.8 (69.5)1
40 All 900 (1800) 6.51 0.08 15.93 (54,404) 20.8 (69.5)
50 All 1100 (2300) 7.65 0.14 19.91 (67,996) 20.8 (69.5)
60 All 1300 (2800) 10.19 0.20 23.89 (81,589) 20.8 (69.5)
70 All 1500 (3200) 12.28 0.27 27.87 (95.181) 20.8 (69.5)
80 All 1700 (3700) 14.66 0.45 30.6 (104,505) 21.4 (70.5)
90 All 2000 (4100) 15.09 0.55 33.0 (112,701) 21.9 (71.5)
100 All 2200 (4600) 15.69 0.60 33.7 (115,092) 23 (73.4)
30 All 700 (1400) 7.13 0.09 16.6 (56,692) 20.8 (69.5)1
40 All 900 (1800) 9.46 0.28 22.2 (75,817) 20.8 (69.5)
50 All 1100 (2300) 11.77 0.57 27.7 (94,600) 20.8 (69.5)
60 All 1300 (2800) 13.96 0.93 29.6 (101,089) 21.1 (70.0)
70 All 1500 (3200) 14.43 1.00 34.5 (117,824) 23 (73.4)
80 All 1700 (3700) 14.93 1.04 35.6 (121,580) 24.7 (76.5)
90 All 2000 (4100) 15.58 1.25 36.5 (124,654) 79.0 (26.1)2
100 All 2200 (4600) 16.17 1.55 37.9 (129,435) 27.1 (80.7)2
1 In this case, the compressor will cycle because its speed is down to the minimum of 35 Hz.
The minimum fan speed for the InRow mode is 30%; the minimum fan speed for HACS and RACS mode is 40%.
2
SA temperature is above 25° C (77° F)
Note: Outdoor temperature is 35° C (95° F)
Note: For ACRD500 series, reduce airflow and cooling capacity specifications by 7% for cooling units run at low input voltage (380 V).

General Data
General Specifications - ACRD200 Series
Data Units Water Cooled Glycol Mixture Cooled
Nominal flow rate entering to the unit l/s (gpm) 0.64 (10.0) 0.64 (10.0)
Design entering temperature °C (°F) 29.4 (85.0) 40.6 (105.0)
Maximum heat rejection kW (Btu/hr) 15.2 (52,000) 15.2 (52,000)
Maximum glycol percentage % 0 40
Entering temperature range for 0.64 l/s (10 gpm) flow °C (°F) 12.8 - 43.3 12.8 - 43.3
rate entering to the unit (55.0 - 110.0) (55.0 - 110.0)
Unit pressure drop at 0.64 l/s (10 gpm) kPa (psi) 33.1 (4.8) 43.4 (6.3)
Fluid-cooled
MODEL ACRD200 Series
AIR SYSTEM - FAN (Standard Filter Installed)
Size - mm (in) 200 (7.9)
Air Volume - l/s (SCFM) 1080 (2290)
Fan Motor - W (HP) each 115 (0.15)
Number of Fans 6
COOLING COIL - COPPER TUBE/ALUMINUM FIN
Face Area - m2 (ft2) 0.37 (3.97)
Rows Deep 2
FILTERS - WASHABLE (STANDARD)
Quantity 2
Size - mm (in) 238 X 933 (9.375 X 36.75)
Depth - mm (in) 13 (1/2)
Efficiency (%) <20% MERV 1
FILTERS - PLEATED (OPTIONAL)
Quantity 2
Size - mm (in) 238 X 933 (9.375 X 36.75)
Depth - mm (in) 51 (2)
Efficiency (%) 30% MERV 8
PHYSICAL DATA
Weight - kg (lbs) 199.09 (438)
Height - mm (in) 1991 (78.39)
Width - mm (in) 300 (11.8)
Depth - mm (in) 1070 (42.13)
CONNECTION SIZES
Liquid
In 7/8-in O DF brazed
Return 7/8-in ODF brazed
Condensate Drain
Drain Line - in 3/16-in ID, 5/16-in OD
REFRIGERANT
Type R410A
Charge - kg (oz) 2.2 (78)

Air Cooled
Data SKU Value
AIR SYSTEM - FAN (Standard Filter Installed)
ACRD100 200 (7.9)
Size - mm (in) ACRD101 200 (7.9)
ACRD500 series 400 (15.8)
ACRD100 1080 (2290)
Air Volume - l/s (SCFM) ACRD101 1080 (2290)
ACRD500 series 2124 (4500)
ACRD100 115 (0.15)
Fan Motor - W (HP) each ACRD101 115 (0.15)
ACRD100 series 6
Number of Fans
ACRD500 series 2
COOLING COIL - COPPER TUBE/ALUMINUM FIN
ACRD100 0.37 (3.97)
Face Area - m2 (ft2) ACRD101 0.37 (3.97)
ACRD500 series 0.56 (6.0)
ACRD100 2
Rows Deep ACRD101 2
ACRD500 series 4
FILTERS - WASHABLE (STANDARD)
Quantity 2
Size - mm (in) 238 X 933 (9.375 X 36.75)
ACRD100 series
Depth - mm (in) 13 (1/2)
Efficiency (%) <20% MERV 1
FILTERS - PLEATED (STANDARD)
Quantity 4
Size - mm (in) 418 x 470 (16.45 x 18.5)
ACRD500 series
Depth - mm (in) 101.6 (4)
Efficiency (%) 30
Quantity 2
Size - mm (in) 238 X 933 (9.375 X 36.75)
ACRD100 series
Depth - mm (in) 51 (2)
Efficiency (%) 30% MERV 8
Quantity 4
Size - mm (in) 418 x 470 (16.45 x 18.5)
ACRD500 series
Depth - mm (in) 101.6 (4)
Efficiency (%) 85
PHYSICAL DATA
ACRD100 series 183 (404)
Weight - kg (lbs)
ACRD500 series 367 (808)
ACRD100 series 1991 (78.39)
Height - mm (in)
ACRD500 series 1991 (78.39)
Width - mm (in)
ACRD500 series 600 (23.62)
ACRD100 series 1070 (42.13)
Depth - mm (in)
ACRD500 series 1070 (42.13)
CONNECTION SIZES
Refrigerant
ACRD100 series 1/2 in ODF brazed
Discharge
ACRD100 0.7 (10)
Maximum pressure drop - bar (PSI) ACRD101 0.7 (10)
ACRD500 series 0.7 (10)
Liquid
Condensate Drain
ACRD100 series 3/16-in ID, 5/16-in OD
Drain Line - in
ACRD500 series 1/2
REFRIGERANT
ACRD100 series R410A (amount determined at installation)
Type
ACRD500 series R407C (amount determined at installation)

Altitude Correction Factors
Room Condition: 72 DB/50% RH
Altitude (ft) 0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
Specific volume (ft3 /lb) 13.58 14.09 14.62 15.18 15.76 16.36 17.00 17.67 18.37 19.11 19.89
Density (lb/ft3) 0.074 0.071 0.068 0.066 0.063 0.061 0.059 0.057 0.054 0.052 0.050
Density Ratio 1.000 0.964 0.929 0.895 0.862 0.830 0.799 0.769 0.739 0.711 0.683
Capacity Correction 1.000 0.981 0.962 0.933 0.913 0.884 0.865 0.846 0.826 0.807 0.787
Density ratio is used for air flow correction factor.
Capacity correction is used to derate performance.
Sound Performance Data

ACRD100 and ACRD200 Series Tested Sound Data
Lp Sound
Fan Speed Airflow m3/s Sound Power dB at Frequency Hz re: 10-12W Pressure dB
Fan RPM re: 20 µPa*
% (SCFM)
125 250 500 1000 2000 4000 8000 dBA** dBA
100 4300 1.08 (2290) 70.3 80.8 83.3 85.3 80.3 77.8 72.3 88.3 82.2
90 3800 0.92 (1950) 68.3 81.8 78.8 80.8 77.3 74.3 68.3 84.5 78.4
80 3450 0.85 (1800) 67.3 80.3 77.3 78.2 76.3 71.8 66.3 82.7 76.6
70 3000 0.78 (1650) 65.3 76.3 74.8 77.8 73.8 67.8 61.3 80.8 74.7
60 2300 0.66 (1400) 62.3 68.3 69.8 74.8 67.8 59.3 53.3 76.5 70.5
*Weighted Sound Pressure dBA in a 28.3 m3 (1000 ft3) room at 1.5 m (5-ft) distance.
**Based on compressor operating at full speed.
ACRD500 Series Air-cooled Tested Sound Data

Lp Sound
Fan Airflow m3/s Sound Power dB at Frequency Hz re: 10-12W Pressure dB re:
Speed% (SCFM) 20 µPa*
125 250 500 1000 2000 4000 8000 dBA** dBA
50 1.27 (2700) 84.5 87.5 78.0 77.5 75.0 66.5 65.5 83.4 72.8
75 1.79 (3800) 92.5 90.0 84.0 81.5 77.5 71.5 68.5 87.6 76.8
100 2.36 (5000) 90.0 98.0 91.0 85.0 81.0 76.5 72.0 92.3 82.8
*Weighted Sound Pressure dBA in an 8200 ft3 (232.2 m3) room at 6 ft (1.8 m) distance.
**Based on compressor operating at full speed.
Electrical Data
Compressor
SKU MCA MOP FLA Power
LRA RLA
ACRD100 - 208-240V, 60Hz 25 40 N/A 87.5 16.0 4.6
ACRD101 - 220-240V, 50Hz N/A N/A 21 97.0 16.3 4.4
ACRD200 - 208-240V, 60Hz 25 40 N/A 87.5 16.0 4.6
ACRD201 - 220-240V, 50Hz N/A N/A 21 97.0 16.3 4.4
ACRD500 - 200-240V, 50/60Hz 54.0 90 - 160* 50 15
ACRD501 - 460-480V, 60Hz 27.0 40 - 139* 23.2 16
ACRD502 - 380-415V, 50Hz - - 26.0 139* 23.2 16
Note: Above data is based on maximum operating condition MCA-Minimum Circuit Ampacity
Note: Installation must comply with national and/or local electrical codes. MOP-Maximum Overcurrent Protection
Note: Use LRA for estimation of inrush current. LRA-Compressor Locked Rotor Amps
* The compressor is powered by the VFD. RLA-Compressor Rated Load Amps
FLA-Full Load Amps

Dimensional Data
ACRD100 and ACRD200 series
na2231b

ACRD500 series
na2465a

NetShelter SX to VX Height Adapter: ACRD100 and ACRD200 series
na2784a
NetShelter SX to VX Height Adapter: ACRD500 series
na2445a
NetShelter SX to 48-U SX Height Adapter: ACRD100 and ACRD200 series
na2788a
NetShelter SX to 48-U SX Height Adapter: ACRD500 series

na2446a

Piping and Mechanical Connections
Refrigeration Piping Diagram (ACRD100 and ACRD500 series)
Bottom piping Top piping
Condenser Condenser
Hot gas
Hot gas
Liquid
Liquid
na2543a
RD
Receiver RD Receiver
Note: Shutoff valves shown nearest to the condensers are not supplied by APC.
ACRD500 series: The shutoff valves nearest to the cooling unit are supplied by APC.
ACRD100 series: The shutoff valves are not supplied and must be ordered.
 Pitch in direction of refrigerant flow; 4 mm per m P-trap

(1/2 in per 10 ft)
Shutoff valves S-trap
Head pressure control valve Inverted P-trap

Check valve Pressure relief valve
Note: Route piping through the top or bottom of the InRow RD.
Note: All lines are Type L ACR copper tubing.
Note: Trap the vertical discharge line every 6 m (20 ft) to ensure proper oil return.
Note: Pipe size should change after the P-trap based on the recommended piping charts
provided with the installation manual. See the piping diagram created for your site.
Note: The maximum piping run is 61 m (200 ft) equivalent length. Size the piping pursuant
to accepted refrigeration practice.
Note: ACRD100 series only: any equivalent length greater than 46 m (150 ft) will result in a
5% decrease in capacity.
Warning: Do not install the air-cooled condenser below the InRow RD. The condenser
must be positioned above or at the same level as the InRow RD to ensure proper
function.

Water cooled piping (ACRD200 series)
Note: Bottom piping shown.
na2765a
 InRow RD  Gate valve
 Balancing valve  Hose bib*
 Strainer, 20 mesh
* Field supplied and installed

Glycol cooled piping (ACRD200 series)
Note: Bottom piping shown.
na2766a
 Expansion tank*  Hose bibs*
 Tank fill*  Gate valves*
 Fluid-cooler  Balancing valve
 Airtrol fitting*  Pump package*
 Temperature and pressure gauges*  Flow switch
 Air vent*  Strainer, 20 mesh*
 InRow RD
* Field supplied and installed

Top piping and power access locations (ACRD100 series and ACRD200 series)
88.9 (3.5)
55.1 (2.2)
47.8 (1.9)
85.6 (3.4)
42.6 (1.7)
38.2 (1.5)
109.7
(4.3)
(3.4)
87.6
154.6
143.4
(6.1)
(5.6)
na2813a

 Low voltage wiring input  Liquid line (ACRD100 series)
Water/glycol in (ACRD200 series)
 Electrical input  Condensate pump outlet
 Hot gas discharge line (ACRD100 series)

Water/glycol out (ACRD200 series)

Bottom piping and power access locations (ACRD100 series and ACRD200 series)
102 (4.0)
88.9 (3.5)
55.1 (2.2)
102.1
(4.0)
122.1
(4.4)
133.6
(4.8)
113
(5.3)
168.8
(6.6)
na2814a

 Electrical input  Condensate pump outlet
 Low voltage wiring input  Hot discharge gas line (ACRD100 series)
Water/glycol out (ACRD200 series)
 Liquid line (ACRD100 series)
Water/glycol in (ACRD200 series)

Top piping and power access locations (ACRD500 series)
547 (21.54)
40 (1.58)
REAR—HOT AISLE 558 (21.97)
73 (2.86)
123 (4.84)
75 (2.95)
325 (12.78)
380 (14.94)
738 (29.04)
47 (1.85)
na2725a
FRONT—COLD AISLE
 Refrigerant discharge line

 Refrigerant liquid line
 Trough for communication cables
 Power connections
 Condensate drain

Bottom piping and power access locations (ACRD500 series)
480 (18.90)
345 (13.58)
404 (15.91) REAR—HOT AISLE
115 (4.53)
184 (7.24)
199 (7.84)
420 (16.54)
796 (31.34)
893 (35.16)
57 (2.25)
na2726a
140 (5.51)
178 (7.00) FRONT—COLD AISLE
 Refrigerant liquid line

 Refrigerant discharge line
 Condensate overflow—50.00 mm (1.97 in)
 Communication connections—27.80 mm (1.09 in)
 Power connections
 Condensate drain

Outdoor Heat Exchangers
Air Cooled Condensers - Mechanical Data (ACRD100 Series)
Air Quantity Fan Unit Connection Size Weight Capacity

Ambient Temp Sound
SKU MBH/1F
°C (°F) Pressure * l/s (CFM) Qty. kW Hot Gas Liquid Kg (Lbs) kW/1C TD
TD
ACCD75214 35 (95) / 40 (104) 65 2380 (5050) 1 1.1 1 1/8 in 7/8 in 82 (180) 2.43 1.28
ACCD75215 46 (115) 66 3040 (6450) 1 1.1 1 1/8 in 7/8 in 118 (260) 4.00 2.11
48
ACCD75216 35 (95) / 40 (104) 59 2140 (4530) 1 0.8 22 mm 18 mm 2.35 1.24
(105.8)
89
ACCD75217 46 (115) 62 4280 (9060) 2 1.6 28 mm 22 mm 4.30 2.27
(196.2)
48
ACCD75218 35 (95) / 40 (104) 59 2140 (4530) 1 0.6 22 mm 18 mm 2.35 1.24
(105.8)
89
ACCD75219 46 (115) 62 4280 (9060) 2 1.3 28 mm 22 mm 4.30 2.27
(196.2)
48
ACCD75220 ** 35 (95) / 40 (104) 59 2140 (4530) 1 0.6 22 mm 18 mm 2.35 1.24
(105.8)
* (dbA) at 10 ft and 100% Fan Speed
** ACCD75220 is CCC certified for use in China.
Air Cooled Condensers Mechanical Data (ACRD500 Series)
Connection Weight
Ambient Air Quantity Fan Unit Size Capacity
Sound Sound (inches)
SKU Temp Pressure * Pressure **
°C (°F) Hot MBH/1F
l/s (CFM) Qty. kW Gas Liquid Kg (Lbs) kW/1C TD
TD
163
ACCD75201 95 (35) 67 62 4955 (10500) 1 2.2 1 3/8 1 3/8 8.8 4.6
(360)
10383 290
ACCD75202 105 (40) 70 65 2 4.4 1 5/8 1 5/8 14.6 7.7
(22000) (640)
14819 458
ACCD75203 115 (46) 72 68 3 6.6 2 1/8 2 1/8 (1010) 25.8 13.6
(31400)
163
ACCD75204 95 (35) 67 62 4955 (10500) 1 2.2 1 3/8 1 3/8 8.8 4.6
(360)
10383 290
ACCD75205 105 (40) 70 65 2 4.4 1 5/8 1 5/8 14.6 7.7
(22000) (640)
14819 458
ACCD75206 115 (46) 72 68 3 6.6 2 1/8 2 1/8 (1010) 25.8 13.6
(31400)
173
ACCD75207 95 (35) 54 51 5711 (12100) 1 2.2 42 22 17.6 9.3
(381)
11940 307
ACCD75208 105 (40) 57 54 2 4.4 42 28 27.1 14.3
(25300) (677)
11374 360
ACCD75209 115 (46) 57 55 2 4.4 54 35 48.2 25.4
(24100) (792)
** (dbA) at 10 ft set area level, and Max Compressor Speed Selected Ambient Temp
Specifications given for conditions at sea level.
Fluid Coolers - Mechanical Data (ACRD200 Series)
Ambient Air Quantity Fan Unit Weight Capacity

Connection
SKU Temp Sound Pressure * MBH/1F kW/1C TD
°C (°F) l/s (CFM) Qty. kW Size (inches) Kg (Lbs) TD
ACFC75210 40 (105) 68 4760 (10100) 2 2.0 1 3/8 205 (450) 3.20 1.69
ACFC75255 35 (95) 65 2380 (5050) 1 1.0 1 1/8 150 (330) 2.36 1.24
ACFC75256 35 (95) 62 4220 (8950) 2 1.6 1 1/2 90 (198) 2.50 1.32
ACFC75257 40 (105) 56 5500 (11650) 2 1.4 2 151 (333) 3.30 1.74

Air Cooled Condensers - Electrical Data (ACRD100 Series)
SKU Voltage Phase Frequency FLA MCA MOP
ACCD75214 208-240V 1 ph 60 Hz 4.8 15 15
ACCD75215 208-240V 1 ph 60 Hz 4.8 15 15
ACCD75216 380-415V 3 ph 50 Hz 1.35 N/A N/A
ACCD75217 380-415V 3 ph 50 Hz 2.7 N/A N/A
ACCD75218 220-240V 1 ph 50 Hz 3.0 N/A N/A
ACCD75219 220-240V 1 ph 50 Hz 6.0 N/A N/A
ACCD75220* 220-240V 1 ph 50 Hz 3.0 N/A N/A
*ACCD75220 is CCC certified for use in China. FLA=Full Load Amps
MCA=Minimum Circuit Amperes
MOP=Maximum Overcurrent Protection
Air Cooled Condensers - Electrical Data (ACRD500 Series)

ACCD75201 208-230V 3 ph 60 Hz 7.0 15.0 25
ACCD75202 208-230V 3 ph 60 Hz 14.0 20.0 35
ACCD75203 208-230V 3 ph 60 Hz 21.0 22.8 40
ACCD75204 460V 3 ph 60 Hz 3.5 15.0 15
ACCD75205 460V 3 ph 60 Hz 7.0 15.0 15
ACCD75206 460V 3 ph 60 Hz 10.5 15.0 20
ACCD75207 400V 3 ph 50 Hz 3.1 N/A N/A
ACCD75208 400V 3 ph 50 Hz 6.2 N/A N/A
ACCD75209 400V 3 ph 50 Hz 6.2 N/A N/A
FLA=Full Load Amps
Fluid Coolers - Electrical Data (ACRD200 Series)

ACFC75210 460V 3 ph 60 Hz 2.6 15 15
ACFC75255 480V 3 ph 60 Hz 1.3 15 15
ACFC75256 380-415V 3 ph 50 Hz 2.7 N/A N/A
ACFC75257 380-415V 3 ph 50 Hz 2.7 N/A N/A
FLA=Full Load Amps

ACCD75201 and ACCD75204
na2449a
na2450a

na2051a

Condensers shown above have eight 22 mm (0.875 in) mounting holes on their lower rails.

ACCD75207
na2452a
na2453a
Condensers shown above have 16 mm (0.63 in) mounting holes on each of their lower legs.
ACCD75214
na2891a
ACCD75215
na2895a

ACCD75216, ACCD75218, and ACCD75220
na2893a
na2896a
ACFC75210
na2890a
ACFC75255
na2899a

ACFC75256
na2894a
ACFC75257
na2898a
Air-cooled Condenser Features
Available in one to three fan configurations, APC offers air-cooled condensers with a vertical air discharge pat-
tern. The RD500 series condensers utilize variable speed EC motor technology for improved sound and energy
performance. All other condensers utilize variable speed motors.
60 Hz specific features:
• Side access panels for ease of cleaning coil

• Constructed with aluminum housing
• Weatherproof control panel with a factory-mounted door interrupt disconnect switch
50 Hz specific features:
• Constructed with painted galvanized steel

Note: A disconnect should be field-supplied based on maximum overcurrent
protection (MOP) numbers.

Guide Specifications
PART 1 — GENERAL
1.01 SUMMARY
A. The environmental control system shall be designed specifically for precision temperature control
applications. It will automatically monitor and control cooling and filtering functions for the
conditioned space. The system shall be built to the highest quality engineering and manufacturing
standards, and shall be floor mounted and configured for horizontal airflow, with draw-through air
pattern, to provide uniform air distribution over the entire face of the coil.
1.02 DESIGN REQUIREMENTS

A. The system shall be as described in the following specification as manufactured by APC.
1. Model: ____________________________.
2. Total net cooling capacity: _______________ kW (MBH).
3. Sensible net cooling capacity: ____________ kW (MBH).
4. Return air dry bulb temperature: _______________ ºC (ºF) DB.
5. Return air wet bulb temperature: _______________ ºC (ºF) WB.
6. Humidity: __________________________% RH.
7. Air volume: _______________________ L/s (CFM).
8. Electrical supply: ____________ V, _________ Hz.
1.03 SUBMITTALS
A. Submittals shall be provided with the proposal and shall include: capacity data, electrical data,
physical data, electrical connection drawing, and piping connection drawing.
1.04 QUALITY ASSURANCE
A. The system shall be completely factory-tested prior to shipment. Testing shall include, but not be
limited to: complete pressure and leak testing to ensure system integrity, dielectric withstand test,
and controls calibration and settings. Each system shall ship with a completed test report to verify
completion of factory testing procedure. The system shall be NRTL listed, MCA, and the electrical
system shall be UL Listed to UL 1995 and CSA 22.2 No. 236.
1.05 WARRANTY
A. System parts shall be warranted for a period of 18 months from date of shipment and 12 months
from startup.
PART 2 — PRODUCT
2.01 STANDARD COMPONENTS
A. Cabinet Construction
1 . Front and rear exterior panels shall be 18 gauge perforated steel with 69.5% open free area,
and equipped with a keyed lock to provide a means of securing access to the internal
components of the unit.
a. ACRD100 and ACRD200 series only: Exterior panels shall be 18 gauge steel with
80 kg/m3 (5 lb/ft3) density foam insulation. Insulation complies with UL94-5VA ASTM
E84 flame spread and smoke developed rating of 25/50.
2 . The frame shall be constructed of 16 gauge formed steel welded for maximum strength. All
units shall provide maintenance from the front and rear, allowing units to be placed within a
row of racks.

3 . All exterior panels and frame shall be powder coated for durability and attractive finish.
Exterior frame and panel color shall have color values: L = 74.50, a = -0.53, b = +8.20.
4 . Units shall include casters and leveling feet to allow ease of installation in the row and provide
a means to level the equipment with adjacent IT racks.
B. Fans
1 . Variable speed direct drive mixed flow DC fan assembly (ACRD100 and ACRD200 series):
a. The unit shall be configured for draw-through air pattern to provide uniform air flow over
the entire face of the coil. Each unit shall include six 200 mm mixed flow direct drive DC
axial fans. Each fan assembly should be designed to provide 180.1 l/s (381.7 CFM) for
total unit airflow of 1080.76 l/s (2290 CFM). The ACRD500 series includes two fans.
Each fan provides 1085.5 l/s (2300 CFM) for a total unit airflow of 2171 l/s (4600 CFM).
b. Variable speed fans: Fans shall be variable speed capable of modulating from 30-100%.
Fans shall soft start to minimize in-rush current.
c. Fan protection: Each fan assembly shall consist of a plastic injection molded bezel with
integral fan discharge finger guard. Inlet of the fan should include a cage type finger
guard.
d. Operation and service: The unit should be capable of operation in the event of a fan
failure. Fans shall be replaceable while the unit is in operation.
2 . Variable speed fan assembly (ACRD500 series):
a. Variable speed fans: The unit is equipped with two variable speed, electronically
commutated, 400-mm backward incline fans complete with inlet volute.
b. Fan protection: discharge finger guard. Outlet of the fan should include a cage type finger
guard.
c. Operation and service: The unit should be capable of operation in the event of a fan
failure.
C. Main Disconnect Switch
1 . The unit shall be provided with thermal-magnetic circuit breakers with interrupt capacity
ratings per UL489/CSA C22.2/IEC-947.
Voltage kAIC
200-240V 50/60Hz 50
380-415V 50Hz 36
460-480V 60Hz 22
2 . Units shall include a main disconnect switch located on the electrical panel in order to
disconnect the power input.
3 . A condenser disconnect shall be field-supplied.
D. Microprocessor Controller
1 . Monitoring and configuration: The display interface shall allow monitoring and configuration
of the air conditioning unit through a menu-based control. Functions include status reporting,
set-up, and temperature set points. Four LEDs report the operational status of the connected air
conditioning unit.
2 . Controls: The microprocessor controller shall come equipped with control keys to allow the
user to navigate between menus, select items, and input alpha numeric information.

3 . Alarms: The microprocessor controller shall activate a visible and audible alarm in the
occurrence of the following events:
a. Cool Fail
b. Air filter clogged
c. Return air sensor fault
d. Supply air sensor fault
e. Rack temperature sensor fault
f. High discharge pressure
g. Low suction pressure
h. Fan fault
i. Water detected
j. Condensate pump fault
k. Air filter run hours violation
l. Group communication fault
m. Supply air high temperature violation
n. Return air high temperature violation
o. Filter DP sensor failure
p. Suction pressure sensor failure
q. Discharge pressure sensor failure
r. Persistent high discharge pressure fault
s. Rack inlet temperature high violation
t. External communication fault
u. Internal communication fault
v. On standby input contact fault
w. A-link isolation relay fault
x. Excessive compressor cycling
y. Condensate pan full (ACRD100 series and ACRD200 series only)
z. Upper fan power supply fault (ACRD100 series and ACRD200 series only)
aa. Lower fan power supply fault (ACRD100 series and ACRD200 series only)
ab. Suction temperature sensor failure (ACRD100 series and ACRD200 series only)
ac. Persistent low suction pressure fault (ACRD100 series and ACRD200 series only)
ad. Condenser fluid valve actuator fault (ACRD200 series only)
ae. Outdoor heat exchanger fault (ACRD200 series only)
af. Factory configuration not completed (ACRD200 series only)
ag. Liquid refrigerant sensor failure (ACRD200 series only)
ah. Compressor drive communication fault (ACRD500 series only)
ai. Compressor drive fault (ACRD500 series only)
aj. Compressor drive warning (ACRD500 series only)
ak. Compressor run hours violation (ACRD500 series only)
al. Condensate pump run hours violation (ACRD500 series only)
am. Fan run hours violation (ACRD500 series only)
an. Supply humidity sensor fault (ACRD500 series only)
ao. High suction pressure
4 . Logging: The microprocessor controller shall log and display all available events. Each alarm
log shall contain time/date stamp as well as operating conditions at the time of occurrence. The
controller shall display the run time hours for major components.
E. Network Management Card
The unit shall include a Network Management Card to provide management through a
computer network through TCP/IP. Management through the network should include the
ability to change set points as well as view and clear alarms.

F. Cooling Coil And Condensate Pan
1 . ACRD100 and ACRD200 series:
a. The cooling coil shall use corrugated aluminum fin and copper tube coils. The coil header
is equipped with a drip plate in the bottom to capture and direct the condensation
accumulating on the suction header tube to the drain pan.
2 . ACRD500 series:
a. The cooling coil shall use raised lance type corrugated aluminum fin and 12.7-mm (1/2-in)
OD copper tube coils. Fin shall be a minimum of 0.0055 in thick. Tube wall shall be a
minimum of 0.016 in thick. Coil end supports shall be a minimum 18 gauge G90
galvanized steel. The coil shall be rated for a maximum pressure of 3447.3 kPa (500 psig)
or higher, and the coils are certified in accordance with UL207. The coil header is
equipped with a drip plate in the bottom to capture and direct the condensation
accumulating on the suction header tube to the drain pan.
G. Compressor
1 . SCROLL COMPRESSOR (ACRD100 series and ACRD200 series only)
a. The high EER (up to 20.0) and few moving parts of scroll compressors shall provide
efficient and reliable operation. Scroll technology has unparalleled ability to withstand
liquid refrigerant ‘slugging’ which is a major cause of compressor failure.
2 . VARIABLE SPEED / VFD ASSEMBLY (ACRD500 series only)
a. Compressor: The unit shall be configured with a variable speed reciprocating hermetic
compressor using a matched VFD. As a result, the compressor speed can be varied
through a range between 30 and 85 Hz to accommodate varying load conditions. VFD
firmware is written to include oil return protection in cases where pipe velocities may drop
to low speeds during low loading periods.
b. Compressor is electrically protected through the VFD.
c. Compressor utilizes a sound jacket for noise reduction.
d. A sight glass is provided for air cooled system oil charging.
H. Condensate Pump
1 . ACRD100 series and ACRD200 series: Dual factory installed and wired condensate pumps
shall pump at 9.8 l/h (2.6 g/hr) at 4.9 m (16 ft) of head. Each pump shall have dual internal
floats.
2 . ACRD500 series: A single factory installed and wired condensate pump shall pump at
11.8 l/h (8.45 g/hr) at 3.5 m (11.5 ft) of head. The pump shall have dual internal floats.
3 . Each pump shall have a condensate reservoir made of polymeric materials to prevent
corrosion.
I. Filters
1 . ACRD100 series and ACRD200 series:
a. The standard filters shall be 20% efficient per ASHRAE 52.1, MERV 1 per ASHRAE
52.2, 1/2 in washable mesh filter.
b. The optional filter shall be high capacity 2 in pleated, UL 900 Class 2, moisture resistant,
with average atmospheric dust spot efficiency of 30%, per AHRAE Standard 52.1, MERV
8 per ASHRAE 52.2.
2 . ACRD500 series:
a. The standard pleated filters shall be 96mm (3.75in) deep, and 30% efficient per ASHRAE
Standard 52.1, UL Class 2 (MERV 8 per ASHRAE 52.2). Filters shall be EN779 G4
efficient.
b. The optional filter shall be 85% efficient per ASHRAE Standard 52.1 (MERV 13 per
ASHRAE 52.2, EN779 F7).

J. Temperature Sensors
1 . Internal Temperature Sensors: Thermistor temperature sensors shall be mounted behind the
front and rear doors to provide control inputs based on supply and return air temperature.
Sensor accuracy shall be within ± 1 degree F accuracy.
2 . Remote Temperature Sensors
a. ACRD500 series: Three remote rack inlet temperature sensors shall be shipped with the
unit to provide control input based on rack inlet temperature.
b. ACRD100 and ACRD200 series: One remote rack inlet temperature sensor shall be
shipped with the unit to provide control input based on rack inlet temperature.
K. Selectable Top Or Bottom Piping (ACRD500 Series)
1 . Pipe connections: The unit is equipped to facilitate field connections from either the top or
bottom. Unit connections shall be made internal to the unit.
2 . Pipe adapter: The unit shall include two pipe adapters that convert a 31.75-mm (1 1/4-in) NPT
to a 31.75-mm (1 1/4-in) BSPT (manufactured in accordance with BS21). Pipe adapters shall
ship loose with the unit for field installation where applicable.
L. Cable Water Detector (Optional)
1 . The optional leak detection sensing cable shall be shipped loose with the unit. If water or other
conductive liquids contact the cable anywhere along its length, the main controller visually
and audibly annunciates the leak.
2 . The optional detector shall be provided with 6.1 m (20 ft) of cable. Cable may be cascaded up
to 24.4 m (80 ft).
M. Bridge Power Cable Trough
1 . An overhead power distribution bridge, that sits between adjacent NetShelter racks and allows
for removal of the unit without disrupting the overhead power cabling, is available as an
accessory.
2 . Cable trough shall be constructed of 16 gauge cold rolled steel with a black powder coat finish.
N. Bridge Data Partition
1 . An overhead cable distribution, that sits between adjacent NetShelter racks and allows for
removal of the unit without disrupting overhead cabling, is available as an accessory.
2 . Data partition shall be constructed of 16 gauge cold rolled steel with a black powder coat
finish.
O. Cooling Fluids (ACRD200 Series)
Water and solutions of propylene or ethylene glycol up to 50% may be used. Solutions of
brine or other aqueous salt are NOT permitted.
P. Freeze Protection (ACRD200 Series)
Per ASHRAE Handbook Fundamentals 2001 21.5, a maximum of 30% ethylene glycol and
35% propylene glycol are needed for freeze protection. See the ASHRAE handbook for more
details.

Guidelines for Installation
The InRow RD provides reliable, accurate temperature control of computer rooms, laboratories, and other
environments that require close tolerance control. The unit incorporates the latest system design innovations to
provide you with optimum efficiency, reliability, and accuracy of control.
The InRow RD unit will provide years of trouble-free service when installed and maintained by
technically qualified personnel. For more detailed information, see the appropriate InRow RD
Installation manual:
ACRD100 series: 990-3211
Room preparation
During the design of the room, consideration should be given to the following factors: ease of entry for
the system, floor-loading factors, and accessibility of piping and wiring.
The room must be sealed with a vapor barrier to minimize moisture infiltration. Polyethylene film
(plastic sheeting) is a good vapor barrier for ceiling and wall applications. Rubber- or plastic-based
paints should be applied to concrete floors and walls. The room should be thoroughly insulated to
minimize thermal loads and make-up air (if required) should be preconditioned to reduce additional
temperature, filtration, and moisture loads.
Service access
For routine service while in the row, at least 914.4 mm (36 in) of clear space must be left in the front and
rear of the unit. To move the equipment outside the row for service, an area of 1219 mm (48 in) of clear
space is required.
Receiving the unit

Your InRow RD unit has been completely tested and inspected prior to shipment. To ensure that you
have received the unit in excellent condition, perform a careful inspection of the crating and the unit
immediately upon receipt. Verify that all parts ordered were received as specified and that the unit is the
correct size and voltage necessary to fulfill your environmental control needs. Report any damage
discovered to the freight carrier. If necessary, contact the APC field service department for help in
repairing or replacing damaged parts. While APC is not responsible for damage incurred in transit, we
want to make sure that you have no undue delays in your system start-up. See the unpacking sheet and
installation manual for more information.
Rigging
The unit is manufactured with a formed steel frame for maximum strength and unit integrity. However,
as with all electrical and mechanical equipment, you must take care with proper rigging of your unit.
When using a forklift to move the unit, use the shipping skid to protect the bottom of the unit. When
using chains, cables, or rope to lift the unit, use spreader bars to prevent damage to the finished panels.
Four threaded M10X16 holes are provided in the top of the frame to accommodate lifting eye bolts that
can be utilized to lift the unit.
Condensate drain
Condensation from the evaporator pan is collected and discharged by the condensate pump to a
condensate line supplied with the unit. Additional condensate piping is required to route to the building
condensate system.
Note: Because of an ongoing program dedicated to product improvement, specifications are

subject to revisions without notice. APC assumes no responsibility, and disclaims all liability
for damages resulting from use of this information or for any errors or omissions.

APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer support
information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact the APC Customer Support Center by telephone or e-mail.
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
For information on how to obtain local customer support, contact the APC representative or other distributors
from whom you purchased your APC product.
© 2010 APC by Schneider Electric. APC, the APC logo, and InRow are owned by Schneider Electric
Industries S.A.S., American Power Conversion Corporation, or their affiliated companies. All other
trademarks are property of their respective owners.
990-3236D-001 6/2010

Jbor-7b6kge R5 en PDF

Uploaded by

Copyright:

Available Formats

Jbor-7b6kge R5 en PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jbor-7b6kge R5 en PDF

Uploaded by

Copyright:

Available Formats

InRow® RD

IN NO EVENT SHALL AMERICAN POWER CONVERSION CORPORATION BE LIABLE FOR

This Publication shall not be for resale in whole or in part.

Microprocessor Controller ............................................. 6

InRow RD Technical Data Manual i

Performance at Percentage of Fan Speed . . . . . . . . . . . . . . . . . . . . 21

General Data .................................................................. 24

Dimensional Data .......................................................... 27

Piping and Mechanical Connections ........................... 30

Outdoor Heat Exchangers ............................................ 37

SKU Selection Width Voltage Plug Type

ACRD100 300 mm 208-240V, 60 Hz, 1 Phase Hard wired

ACRD101 300 mm 220-240V, 50 Hz, 1 Phase Hard wired

ACRD200 300 mm 208-240V, 60 Hz, 1 Phase Hard wired

ACRD201 300 mm 220-240V, 50 Hz, 1 Phase Hard wired

ACRD500 600 mm 200-240V, 50/60 Hz, 3 Phase Hard wired

ACRD501 600 mm 460-480V, 60 Hz, 3 Phase Hard wired

ACRD502 600 mm 380-415V, 50/60 Hz, 3 Phase Hard wired

InRow RD Technical Data Manual iii

InRow RD Technical Data Manual 1

Scalable for High Density

2 InRow RD Technical Data Manual

Dimensions are shown in mm (in).

InRow RD Technical Data Manual 3

4 InRow RD Technical Data Manual

InRow RD Technical Data Manual 5

 Critical Alarm LED

 Liquid Crystal Display (LCD)

 Menu Selection scroll keys

Microprocessor Controller Control Type Logging

6 InRow RD Technical Data Manual

InRow RD Technical Data Manual 7

 Removable rear door  Adjustable leveling feet

 Side panel latch  Display interface

 Removable side panel  Removable front door

 Rear casters (non-swiveling)  Door lock (front and rear)

 Front casters (swiveling)

8 InRow RD Technical Data Manual

 Electrical control box 1  Compressor

 Electrical control box 2  Front air block panel

 Return air temperature  Evaporator fans (6 total)

 Condensate pan floats (2  Expansion valve

 Condensate pan  Evaporator coil

InRow RD Technical Data Manual 9

 Filter/dryer  Hot gas bypass valve

 Pressure transducer (2 total, located  Liquid line shutoff solenoid

 Filter differential pressure port  Electrical control box 1

 Air filter (2 total)  Power supply unit (bottom)

 Condensate pump (2 total)  Power supply unit (top)

 Electrical control box 2  Service junction box (top entry shown)

10 InRow RD Technical Data Manual

 Electrical control box 1 (retractable)  Compressor

 Electrical control box 2  Front air block panel

 Condensate pumps (2 total)  Evaporator fans (6 total)

 Bypass shutoff valve (2-way)  Condensate pan

 Water control actuator  Condensate pan floats (2 total)

 Water regulating valve (3-way )  Expansion valve

 Brazed plate heat exchanger  Evaporator coil

InRow RD Technical Data Manual 11