ACT8846 Datasheet

ACT8846 Rev 7.
0, 06-Dec-2017
Advanced PMU for Multi-core Application Processors
FEATURES GENERAL DESCRIPTION

INTEGRATED POWER SUPPLIES The ACT8846 is a complete, cost effective, and
 Four DC/DC Step-Down (Buck) Regulators highly-efficient ActivePMUTM power management
solution optimized for the power, voltage
 2 x 2.8A, 2 x 1.5A sequencing and control requirements of Rockchip
 Five Low-Noise LDOs RK31x8 application processor family.
 2 x 150mA, 3 x 350mA The ACT8846 features four fixed-frequency,
 Three Low-Input Voltage LDOs current-mode, synchronous PWM step-down
converters that achieve peak efficiencies of up to
 1 x 150mA, 2 x 350mA 97%. These regulators operate with a fixed
 One Low IQ Keep-Alive LDO frequency of 2.25MHz, minimizing noise in sensitive
applications and allowing the use of small external
 Backup Battery Charger components. These buck regulators supply up to
2.8A of output current and can fully satisfy the
SYSTEM CONTROL AND INTERFACE power and control requirements of the multi-core
 Four General Purpose I/O with PWM Drivers application processor. Dynamic Voltage Scaling
(DVS) is supported either by dedicated control pins,
 I2C Serial Interface or through I2C interface to optimize the energy-per-
 Interrupt Controller task performance for the processor. This device
also include eight low-noise LDOs (up to 350mA
SYSTEM MANAGEMENT per LDO), one always-on LDO and an integrated
backup battery charger to provide a complete
 Reset Interface and Sequencing Controller power system for the processor.
 Power on Reset
The power sequence and reset controller provides
 Soft / Hard Reset power-on reset, SW-initiated reset, and power cycle
 Watchdog Supervision reset for the processor. It also features the
 Multiple Sleep Modes watchdog supervisory function. Multiple sleep
modes with autonomous sleep and wake-up
 Thermal Management Subsystem sequence control are supported.
The thermal management and protection
subsystem allows the host processor to manage the
APPLICATIONS power dissipation of the PMU and the overall
system dynamically. The PMU provides a thermal
 Tablet PC warning to the host processor when the
 Mobile Internet Devices (MID) temperature reaches a certain threshold such that
the system can turn off some of the non-essential
 E-books functions, reduce the clock frequency and etc to
 Personal Navigation Devices manage the system temperature.
 Smart Phones The ACT8846 is available in a compact, Pb-Free
and RoHS-compliant TQFN66-48 package.
Innovative PowerTM -1- www.active-semi.com

ActivePMUTM is a trademark of Active-Semi. Copyright © 2016-2017 Active-Semi, Inc.
I2CTM is a trademark of NXP.
ACT8846
Rev 7.0 06-Dec-2017
FUNCTIONAL BLOCK DIAGRAM

VP1 To Battery
SW1
OUT1
REG1
FB1
GP14
ACT8846
VP2 To Battery
VIO
SW2
OUT2
REG2
nRSTO
OUT2
INL2
GP2
nPBIN
PUSH BUTTON VP3 To Battery
VIO
nPBSTAT SW3
OUT3
REG3
OUT3
VIO
GP3
nIRQ
VP4 To Battery
SW4
OUT4
REG4
PWRHLD
OUT4
PWREN
GP14
To Battery
System
INL1
VSELR2
Control OUT5
REG5
LDO OUT5
SCL OUT6
REG6
LDO OUT6
SDA
REG7 OUT7
OUT7
LDO
REFBP
Reference
INL2 To Battery
REG8 OUT8
OUT8
LDO
GPIO1
GPIO2 REG9 OUT9

OUT9
LDO
GPIO3
GPIO4 INL3 To Battery
GPIO5
GPIO6 REG10 OUT10

OUT10
LDO
REG11 OUT11
OUT11
LDO
REG12 OUT12
OUT12
LDO
REG13 OUT13
OUT13
RTC LDO
GA EP

ACT8846
Rev 7.0 06-Dec-2017
ORDERING INFORMATION
PART NUMBER VOUT1 VOUT2 VOUT3 VOUT4 VOUT5 VOUT6 VOUT7 VOUT8 VOUT9 VOUT10 VOUT11 VOUT12 VOUT13
ACT8846QM460-T Adjustable 1.0V 1.0V 3.0V 1.0V 1.2V 1.8V 3.3V 3.3V 3.3V 1.8V 2.8V 1.8V
ACT8846QM468-T Adjustable 1.0V 1.0V 3.0V 1.0V 1.2V 1.8V 3.3V 3.3V 3.3V 1.8V 2.8V 1.8V
ACT8846QM490-T Adjustable 3.3V 1.1V 2.0V 3.3V 1.0V 3.3V 3.3V 3.3V 1.0V 1.8V 1.8V 1.8V
ACT8846QM468-T15 Adjustable 1.0V 1.0V 3.0V 1.0V 1.2V 1.8V 3.3V 3.3V 3.3V 1.8V 2.8V 1.8V
ACT8846QM106-T 1.2V 0.95V 3.3V 1.8V 1.8V 1.8V 3.3V 1.2V 2.8V 1.5V 2.8V 1.8V OFF
ACT8846QM107-T 1.8V 0.9V 1.2V 3.0V 3.3V 1.8V 1.8V 3.3V 3.3V 3.3V 2.5V 3.3V 1.8V
PACKAGE PINS TEMPERATURE RANGE
TQFN66-48 48 -40°C to +85°C
: All Active-Semi components are RoHS Compliant and with Pb-free plating unless specified differently. The term Pb-free means
semiconductor products that are in compliance with current RoHS (Restriction of Hazardous Substances) standards.
: Push button 10s shut down function is supported in ACT8846QM468-T and ACT8846QM490-T and ACT8846QM468-T15.
ACT8846QM_ _ _-T
Product Number
Package Code
Pin Count
Option Code
Tape and Reel

ACT8846
Rev 7.0 06-Dec-2017
PIN CONFIGURATION
TOP VIEW
OUT13
GPIO4
GPIO1
GPIO2
GPIO3
OUT3
OUT5
OUT6
OUT7
INL1
VP3
VP3
SW3 GPIO5
SW3 GPIO6
GP3 nIRQ
OUT10 nRSTO
OUT11 ACTIVE PWRHLD
INL3
8846QM nPBIN
DATE CODE
OUT12 VP1
VSELR2 FB1
nPBSTAT SW1
GP2 GP14
SW2 SW4
EP
SW2 VP4
VP2
VP2
OUT2
PWREN
REFBP
INL2
OUT9
GA
OUT4
OUT8
SDA
SCL
Thin - QFN (TQFN66-48)

ACT8846
Rev 7.0 06-Dec-2017
PIN DESCRIPTIONS
PIN NAME DESCRIPTION
1, 2 SW3 Switch Node for REG3.
Power Ground for REG3. Connect GP14, GP2, GP3, and GA together at a single
3 GP3
point as close to the IC as possible.
4 OUT10 REG10 output. Bypass it to ground with a 2.2µF capacitor.
6 INL3 Power input for REG10, REG11 and REG12.
Output Voltage Selection for REG2. Drive to logic low to select default output voltage.
8 VSELR2
Drive to logic high to select secondary output voltage.
Active-Low Open-Drain Push-Button Status Output. nPBSTAT is asserted low

9 nPBSTAT
whenever the nPBIN is pushed, and is high-Z otherwise.
Power ground for REG2. Connect GP14, GP2, GP3, and GA together at a single
10 GP2
point as close to the IC as possible.
11, 12 SW2 Switch Node for REG2.
Power input for REG2. Bypass to GP2 with a high quality ceramic capacitor placed as
13, 14 VP2
close to the IC as possible.
15 OUT2 Output Voltage Sense for REG2.
Power Enable Input for REG3. PWREN is functional only when PWRHLD is driven
16 PWREN high. Drive PWREN to a logic high to turn on the REG3. Drive PWREN to a logic low
to turn off the REG3.
Reference Bypass. Connect a 0.047μF ceramic capacitor from REFBP to GA. This
17 REFBP
pin is discharged to GA in shutdown.
18 INL2 Power Input for REG8, REG9.
20 GA Analog Ground.
21 OUT4 Output voltage sense for REG4.
23 SDA Data Input for I2C Serial Interface. Data is read on the rising edge of SCL.
24 SCL Clock Input for I2C Serial Interface.
Power input for REG4. Bypass to GP14 with a high quality ceramic capacitor placed
25 VP4
as close to the IC as possible.

ACT8846
Rev 7.0 06-Dec-2017
PIN DESCRIPTIONS CONT’D

PIN NAME DESCRIPTION
26 SW4 Switch Node for REG4.
Power Ground for REG1 and REG4. Connect GP14, GP2, GP3, and GA together at a
27 GP14
single point as close to the IC as possible.
28 SW1 Switch Node for REG1.
Output Feedback Sense for REG1. For the adjustable output voltage options, connect
29 FB1 this pin to the center of the output feedback resistor divider for voltage setting,
connect this pin to the output directly to regulate the output voltage at 1.2V.
Power Input for REG1. Bypass to GP14 with a high quality ceramic capacitor placed
30 VP1
as close to the IC as possible.
Master Enable Input. Drive nPBIN to GA through a 50kΩ resistor for 32ms to enable
31 nPBIN the IC. Drive nPBIN to GA through a 50kΩ resistor for 10 seconds to disable the IC.
Drive nPBIN directly to GA to assert a Manual-Reset condition.
Power Hold Input, enable input for REG1, REG2, REG4, REG5, REG6, REG8 and
32 PWRHLD
REG10. PWRHLD is internally pulled down to GA through a 900kΩ resistor.
33 nRSTO Open-Drain Reset Output.
34 nIRQ Open-Drain Interrupt Output.
General Purpose I/O #6. Configured as PWM LED driver output for up to 6mA current
35 GPIO6 with programmable frequency and duty cycle. See the PWM LED Drive section for
more information.
36 GPIO5 with programmable frequency and duty cycle. See the PWM LED Driver section for
more information.
39 GPIO4 with programmable frequency and duty cycle. See the PWM LED Driver section for
more information.
41 INL1 Power Input for REG5, REG6, REG7.
43 GPIO3 with programmable frequency and duty cycle. See the PWM LED Drier section for
more information.
General Purpose I/O #2. Configured as VSELR4 for Voltage Selection of REG4. Drive
44 GPIO2 to logic low to select default output voltage. Drive to logic high to select secondary
output voltage.
General Purpose I/O #1. Configured as VSELR3 for Voltage Selection of REG3. Drive
45 GPIO1 to logic low to select default output voltage. Drive to logic high to select secondary
output voltage.
46 OUT3 Output Voltage Sense for REG3.
Power input for REG3. Bypass to GP3 with a high quality ceramic capacitor placed as
47,48 VP3
close to the IC as possible.
EP EP Exposed Pad. Must be soldered to ground on PCB.
: Only for ACT8846QM468.

ACT8846
Rev 7.0 06-Dec-2017
ABSOLUTE MAXIMUM RATINGS

PARAMETER VALUE UNIT
INL1, INL2, INL3 to GA; VP1, SW1, FB1 to GP14; VP2, SW2, OUT2 to GP2; VP3,
-0.3 to 6 V
SW3, OUT3 to GP3; VP4, SW4, OUT4 to GP14
GP14, GP2, GP3 to GA -0.3 to + 0.3 V
OUT5, OUT6, OUT7, OUT13 TO GA -0.3 to INL1 + 0.3 V
OUT8, OUT9, GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, VSELR2, nPBIN, -0.3 to INL2 + 0.3 V
OUT10, OUT11, OUT12 to GA -0.3 to INL3 + 0.3 V

Junction to Ambient Thermal Resistance 21 °C/W
Operating Ambient Temperature Range -40 to 85 °C
Operating Junction Temperature -40 to 125 °C
Storage Temperature -55 to 150 °C
Lead Temperature (Soldering, 10 sec) 300 °C
: Do not exceed these limits to prevent damage to the device. Exposure to absolute maximum rating conditions for long periods may
affect device reliability.

ACT8846
Rev 7.0 06-Dec-2017
I2C INTERFACE ELECTRICAL CHARACTERISTICS

(VINL2 = 3.6V, TA = 25°C, unless otherwise specified.)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

SCL, SDA Input Low VINL2 = 3.1V to 5.5V, TA = -40ºC to 85ºC 0.35 V
SCL, SDA Input High VINL2 = 3.1V to 5.5V, TA = -40ºC to 85ºC 1.55 V
SDA Leakage Current 1 µA
SCL Leakage Current 1 µA
SDA Output Low IOL = 5mA 0.35 V
SCL Clock Period, tSCL 1.5 µs
SDA Data Setup Time, tSU 100 ns
SDA Data Hold Time, tHD 300 ns
Start Setup Time, tST For Start Condition 100 ns
Stop Setup Time, tSP For Stop Condition 100 ns
Figure 1:
I2C Compatible Serial Bus Timing
tSCL
SCL
tST tHD tSU tSP
SDA
Start Stop
condition condition

ACT8846
Rev 7.0 06-Dec-2017
GLOBAL REGISTER MAP

BITS
BLOCK ADDRESS
D7 D6 D5 D4 D3 D2 D1 D0
NAME nBATLEVMSK nBATSTAT VBATDAT Reserved BATLEV[3] BATLEV[2] BATLEV[1] BATLEV[0]
SYS 0x00
DEFAULT 0 R R R 0 1 0 0
NAME nTMSK TSTAT Reserved Reserved Reserved Reserved Reserved Reserved
SYS 0x01
DEFAULT 0 R 0 0 0 0 0 0
NAME ON Reserved Reserved Reserved Reserved PHASE nFLTMSK OK
REG1 0x12
DEFAULT 1 1 0 0 1 0 0 R
NAME Reserved Reserved VSET0[5] VSET0[4] VSET0[3] VSET0[2] VSET0[1] VSET0[0]
REG2 0x20
DEFAULT 0 0 0 1 0 0 0 0
REG2 0x21
DEFAULT 0 0 0 1 0 0 0 0
REG2 0x22
DEFAULT 1 1 0 0 1 0 0 R
REG3 0x30
DEFAULT 0 0 0 1 0 0 0 0
REG3 0x31
DEFAULT 0 0 0 1 0 0 0 0
REG3 0x32
DEFAULT 1 1 0 1 1 1 0 R
REG4 0x40
DEFAULT 0 0 1 1 0 1 1 0
REG4 0x41
DEFAULT 0 0 1 1 0 1 1 0
REG4 0x42
DEFAULT 1 1 0 0 1 1 0 R
NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0]
REG5 0x50
DEFAULT 0 1 0 1 0 0 0 0
NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK
REG5 0x51
DEFAULT 1 1 0 0 1 1 0 R
REG6 0x58
DEFAULT 0 1 0 1 1 0 0 0
REG6 0x59
DEFAULT 0 1 0 0 1 1 0 R
REG7 0x60
DEFAULT 0 1 1 0 0 1 0 0
REG7 0x61
DEFAULT 0 1 0 0 1 1 0 R
REG8 0x68 
DEFAULT 0 1 1 1 1 0 0 1
REG8 0x69
DEFAULT 0 1 0 0 1 1 0 R
: Default values of ACT8846QM468-T.

ACT8846
Rev 7.0 06-Dec-2017
GLOBAL REGISTER MAP CONT’D

BITS
BLOCK ADDRESS
D7 D6 D5 D4 D3 D2 D1 D0
REG9 0x70
DEFAULT 0 1 1 1 1 0 0 1
REG9 0x71
DEFAULT 0 1 0 0 1 1 0 R
REG10 0x80
DEFAULT 0 1 1 1 1 0 0 1
REG10 0x81
DEFAULT 0 1 0 0 1 1 0 R
REG11 0x90
DEFAULT 0 1 1 0 0 1 0 0
REG11 0x91
DEFAULT 1 1 0 0 1 1 0 R
REG12 0xA0
DEFAULT 0 1 1 1 0 1 0 0
REG12 0xA1
DEFAULT 0 1 0 0 1 1 0 R
NAME ON Reserved Reserved Reserved Reserved Reserved Reserved Reserved
REG13 0xB1
DEFAULT 1 0 0 0 0 0 0 0
NAME PBAMSK PBDMSK Reserved Reserved Reserved Reserved WDSREN WDPCEN
PB 0xC0
DEFAULT 0 0 0 0 0 0 0 0
NAME INTADR [7] INTADR [6] INTADR [5] INTADR [4] INTADR [3] INTADR [2] INTADR [1] INTADR [0]
PB 0xC1
DEFAULT R R R R R R R R
NAME PBASTAT PBDSTAT PBDAT Reserved Reserved Reserved Reserved Reserved
PB 0xC2
DEFAULT R R R R R R R R
NAME Reserved Reserved Reserved OFFSYS OFFSYSCLR Reserved Reserved SIPC
PB 0xC3
DEFAULT 0 0 0 0 0 0 0 0
NAME Reserved Reserved Reserved Reserved Reserved Reserved PCSTAT SRSTAT
PB 0xC5
DEFAULT 0 0 0 0 0 0 R R
NAME PWM6EN FRE6[2] FRE6[1] FRE6[0] DUTY6[3] DUTY6[2] DUTY6[1] DUTY6[0]
GPIO6 0xE3
DEFAULT 0 0 0 0 0 0 0 0
GPIO5 0xE4
DEFAULT 0 0 0 0 0 0 0 0
GPIO3 0xF4
DEFAULT 1 1 0 1 0 1 1 1
GPIO4 0xF5
DEFAULT 0 0 0 0 0 0 0 0
: Default values of ACT8846QM468-T.
Innovative PowerTM - 10 - www.active-semi.com

ACT8846
Rev 7.0 06-Dec-2017
REGISTER AND BIT DESCRIPTIONS

BLOCK ADDRESS BIT NAME ACCESS DESCRIPTION
Battery Voltage Level Interrupt Mask. Set this bit to 1 to unmask
SYS 0x00 [7] nBATLEVMSK R/W the interrupt. See the Programmable Battery Voltage Monitor
section for more information
Battery Voltage Status. Value is 1 when BATLEV interrupt is
SYS 0x00 [6] nBATSTAT R
generated, value is 0 otherwise.
Battery Voltage Monitor real time status. Value is 1 when VBAT <
SYS 0x00 [5] VBATDAT R
BATLEV, value is 0 otherwise.
SYS 0x00 [4] - R/W Reserved.
Battery Voltage Detect Threshold. Defines the BATLEV voltage
SYS 0x00 [3:0] BATLEV R/W threshold. See the Programmable Battary Voltage Monitor
section for more information.
SYS 0x01 [7] nTMSK R/W Thermal Interrupt Mask. Set this bit to 1 to unmask the interrupt.
Thermal Interrupt Status. Value is 1 when a thermal interrupt is
SYS 0x01 [6] TSTAT R
generated, value is 0 otherwise.
SYS 0x01 [5:0] - R/W Reserved.
Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit
REG1 0x12 [7] ON R/W
to 0 to disable the regulator.
REG1 0x12 [6:3] - R Reserved.
Regulator Phase Control. Set bit to 1 for the regulator to operate
REG1 0x12 [2] PHASE R/W 180° out of phase with the oscillator, clear bit to 0 for the
regulator to operate in phase with the oscillator.
Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts,
REG1 0x12 [1] nFLTMSK R/W
clear bit to 0 to disable fault-interrupts.
Regulator Power-OK Status. Value is 1 when output voltage
REG1 0x12 [0] OK R
exceeds the power-OK threshold, value is 0 otherwise.
Primary Output Voltage Selection. Valid when VSEL is driven
REG2 0x20 [5:0] VSET0 R/W low. See the Output Voltage Programming section for more
information
Secondary Output Voltage Selection. Valid when VSEL is driven
REG2 0x21 [5:0] VSET1 R/W high. See the Output Voltage Programming section for more
information.
REG2 0x22 [0] OK R

information

ACT8846
Rev 7.0 06-Dec-2017
REGISTER AND BIT DESCRIPTIONS CONT’D

information.
REG3 0x32 [0] OK R
information
information.
REG4 0x42 [0] OK R
Output Voltage Selection. See the Output Voltage Programming
REG5 0x50 [5:0] VSET R/W
Output Discharge Control. When activated, LDO output is
discharged to GA through 1.5kΩ resistor when in shutdown. Set
REG5 0x51 [2] DIS R/W
bit to 1 to enable output voltage discharge in shutdown, clear bit
to 0 to disable this function.
REG5 0x51 [0] OK R

ACT8846
Rev 7.0 06-Dec-2017

Regulator Fault Mask Control. Set bit to 1 enable fault-
interrupts, clear bit to 0 to disable fault-interrupts.
REG6 0x59 [0] OK R
Regulator Enable Bit. Set bit to 1 to enable the regulator, clear
bit to 0 to disable the regulator.
REG7 0x61 [0] OK R
REG8 0x69 [0] OK R
REG9 0x71 [0] OK R

ACT8846
Rev 7.0 06-Dec-2017

REG10 0x81 [7] ON R/W
REG10 0x81 [0] OK R
REG11 0x91 [7] ON R/W
REG11 0x91 [0] OK R
REG12 0xA0 [7:6] - R Reserved.
REG12 0xA0 [5:0] VSET R/W
REG12 0xA1 [7] ON R/W
REG12 0xA1 [6:3] - R Reserved.
REG12 0xA1 [2] DIS R/W
REG12 0xA1 [1] nFLTMSK R/W
REG12 0xA1 [0] OK R
REG13 0xB1 [7] ON R/W
REG13 0xB1 [6:0] - R Reserved.
nPBIN Assertion Interrupt Control. Set this bit to 1 to generate
PB 0xC0 7 nPBAMSK R/W
an interrupt when nPBIN is asserted.
nPBIN De-assertion Interrupt Control. Set this bit to 1 to
PB 0xC0 6 nPBDMSK R/W
generate an interrupt when nPBIN is de-asserted.
PB 0xC0 [5:2] - R Reserved.
Watchdog Soft-Reset Enable. Set this bit to 1 to enable
watchdog function. When the watchdog timer expires, the PMU
PB 0xC0 1 WDSREN R/W
commences a soft-reset routine. This bit is automatically reset to
0 when entering sleep mode.

ACT8846
Rev 7.0 06-Dec-2017

Watchdog Soft-Reset Enable. Set this bit to 1 to enable
watchdog function. When the watchdog timer expires, the PMU
PB 0xC0 1 WDSREN R/W
commences a soft-reset routine. This bit is automatically reset to
0 when entering sleep mode.
Watchdog Power-Cycle Enable. Set this bit to 1 to enable
watchdog function. When watchdog timer expires, the PMU
PB 0xC0 0 WDPCEN R/W
commence a power cycle. This bit is automatically reset to 0
when entering sleep mode.
Interrupt Address. It holds the address of the block that triggers
PB 0xC1 [7:0] INTADR R the interrupt. This byte defaults to 0xFF and is automatically set
to 0xFF after being read. Bit 7 is the MSB while Bit 0 is the LSB.
nPBIN Assertion Interrupt Status. The value of this bit is 1 if the
PB 0xC2 7 PBASTAT R
nPBIN Assertion Interrupt is triggered.
nPBIN De-assertion Interrupt Status. The value of this bit is 1 if
PB 0xC2 6 PBDSTAT R
the nPBIN De-assertion Interrupt is triggered.
nPBIN Status bit. This bit contains the real-time status of the
PB 0xC2 5 PBASTAT R nPBIN pin. The value of this bit is 1 if nPBIN is asserted, and is 0
if nPBIN is de-asserted.
Global Off Control. Set OFFSYSCLR[ ] to 1 first, then set this bit
PB 0xC3 [4] OFFSYS R/W to 1 to turn off all outputs.
Global Off Control State Clear bit. Set bit to 1, then set OFFSYS
PB 0xC3 [3] OFFSYSCLR R/W [ ] to 1 to turn off all outputs.
Software Initiated Power Cycle. When this bit is set, the PMU
PB 0xC3 0 SIPC R/W
commences a power cycle after 8ms delay.
Power-cycle Flag. The value of this bit is 1 after a power cycle.
PB 0xC5 1 PCSTAT R/W
This bit is automatically cleared to 0 after read.
Soft-reset Flag. The value of this bit is 1 after a soft-reset. This
PB 0xC5 0 SRSTAT R/W
bit is automatically cleared to 0 after read.

ACT8846
Rev 7.0 06-Dec-2017

GPIO6 0xE3 [7] PWM6EN R/W PWM Function Enable. Set 1 to enable PWM function of GPIO6.
PWM Frequency Selection Bits for GPIO6. See the Table 6 for
GPIO6 0xE3 [6:4] FRE6 R/W
code to frequency cross.
Duty Cycle Selection Bits for GPIO6. See the Table 7 for code to
GPIO6 0xE3 [3:0] DUTY6 R/W
duty cross.
GPIO5 0xE4 [7] PWM5EN R/W PWM Function Enable. Set 1 to enable PWM function of GPIO5.
GPIO5 0xE4 [6:4] FRE5 R/W
GPIO5 0xE4 [3:0] DUTY5 R/W
duty cross.
GPIO3 0xF4 [7] PWM3EN R/W PWM Function Enable. Set 1 to enable PWM function of GPIO3.
GPIO3 0xF4 [6:4] FRE3 R/W
GPIO3 0xF4 [3:0] DUTY3 R/W
duty cross.
GPIO4 0xF5 [7] PWM4EN R/W PWM Function Enable. Set 1 to enable PWM function of GPIO4.
GPIO4 0xF5 [6:4] FRE4 R/W
GPIO4 0xF5 [3:0] DUTY4 R/W
duty cross.

ACT8846
Rev 7.0 06-Dec-2017
SYSTEM CONTROL ELECTRICAL CHARACTERISTICS


Input Voltage Range 3.0 5.5 V
UVLO Threshold Voltage VINL2 Rising, BATLEV[3:0]=0001 2.6 2.8 3.0 V
UVLO Hysteresis VINL2 Hysteresis 200 mV
Operating Supply Current All Regulators Enabled but no load 0.6 1.2 mA
Shutdown Supply Current All Regulators Disabled except REG13 10 20 µA
Oscillator Frequency 2.0 2.25 2.5 MHz

Logic High Input Voltage 
1.4 V
Logic Low Input Voltage 0.4 V
Leakage Current V[nIRQ] = V[nRSTO] = 4.2V 1 µA
Low Level Output Voltage nIRQ, nRSTO, ISINK = 5mA 0.3 V
nRSTO Delay 100 

ms
Thermal Shutdown Temperature Temperature rising 160 °C

Thermal Shutdown Hysteresis 20 °C
: PWRHLD, PWREN, VSELR2, GPIO1, GPIO2 are logic inputs.

: Typical value shown. Actual value may vary from (T-1ms) x 85% to T x 115%, where T = 100ms.

ACT8846
Rev 7.0 06-Dec-2017
STEP-DOWN DC/DC ELECTRICAL CHARACTERISTICS

(VVP1 = VVP2 = VVP3 = VVP4 = 3.6V, TA = 25°C, unless otherwise specified.)
PARAMETER CONDITIONS MIN TYP MAX UNIT

Operating Voltage Range 2.7 5.5 V
UVLO Threshold Input Voltage Rising 2.5 2.6 2.7 V
UVLO Hysteresis Input Voltage Falling 100 mV
Standby Supply Current VOUT = 103%, Regulator Enabled 72 100 µA
Shutdown Current VVP = 5.5V, Regulator Disabled 0 2 µA

VOUT ≥ 1.0V, IOUT = 10mA -1% VNOM 1% V
Output Voltage Accuracy
VOUT < 1.0V, IOUT = 10mA -10 10 mV
Line Regulation VVP = Max (VNOM +1V, 3.2V) to 5.5V

0.15 %/V
Load Regulation REG1/4 IOUT = 10mA to IMAX 1.70 %/A
Load Regulation REG2/3 IOUT = 10mA to IMAX 1.00 %/A
Power Good Threshold VOUT Rising 93 %VNOM
Power Good Hysteresis VOUT Falling 2 %VNOM
VOUT ≥ 20% of VNOM 2 2.25 2.5 MHz
Switching Frequency
VOUT = 0V 550 kHz
Soft-Start Period 400 µs
Minimum On-Time 75 ns
REG1 AND REG4
Maximum Output Current 1.5 A
Current Limit 1.8 2.2 2.7 A
PMOS On-Resistance ISW = -100mA 0.11 Ω
NMOS On-Resistance ISW = 100mA 0.08 Ω
SW Leakage Current VVP = 5.5V, VSW = 0 or 5.5V 0 2 µA
Input Capacitor 4.7 µF
Output Capacitor 33 µF
Power Inductor 1.0 2.2 3.3 µH
REG2 AND REG3
Maximum Output Current 2.8 A
Current Limit 3.5 4.2 A
PMOS On-Resistance ISW = -100mA 0.07 Ω
NMOS On-Resistance ISW = 100mA 0.08 Ω
SW Leakage Current VVP = 5.5V, VSW = 0 or 5.5V 0 2 µA
Input Capacitor 10 µF
Output Capacitor 44 µF
Power Inductor 0.5 1 2.2 µH
: VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section.
: IMAX Maximum Output Current.

ACT8846
Rev 7.0 06-Dec-2017
LOW-NOISE LDO ELECTRICAL CHARACTERISTICS

(VINL1 = VINL2 = 3.6V, COUT5 = COUT6 = COUT7 = COUT8 = COUT9 = 2.2µF, TA = 25°C, unless otherwise specified.)

VOUT ≥ 1.0V, IOUT = 10mA -1 VNOM 1 %
VOUT < 1.0V, IOUT = 10mA -10 10 mV
Line Regulation VINL = Max (VOUT + 0.5V, 3.6V) to 5.5V 0.5 mV
Load Regulation IOUT = 1mA to IMAX 0.1 V/A
f = 1kHz, IOUT = 20mA, VOUT = 1.2V 75
Power Supply Rejection Ratio dB
Regulator Enabled 25
Supply Current per Output µA
Regulator Disabled 0 2
Soft-Start Period VOUT = 3.0V 140 µs
Power Good Threshold VOUT Rising 92 %
Power Good Hysteresis VOUT Falling 3.5 %
IOUT = 20mA, f = 10Hz to 100kHz, VOUT =
Output Noise 30 µVRMS
1.2V
Discharge Resistance LDO Disabled, DIS[ ] = 1 1.5 kΩ
LDO rated at 150mA (REG5 & REG6)
Dropout Voltage IOUT = 80mA, VOUT > 3.1V 140 280 mV
Maximum Output Current 150 mA

Current Limit VOUT = 95% of regulation voltage 180 mA
Recommend Output Capacitor 2.2 µF
LDO rated at 350mA (REG7, REG8 & REG9)

: Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the
regulation voltage (for 3.1V output voltage or higher).
: LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage.
Under heavy overload conditions the output current limit folds back by 50% (typ.)

ACT8846
Rev 7.0 06-Dec-2017
LOW-INPUT VOLTAGE LDO ELECTRICAL CHARACTERISTICS

(VINL3 = 3.6V, COUT10 = COUT11 = COUT12 = 2.2µF, TA = 25°C, unless otherwise specified.)

VOUT ≥ 1.0V, IOUT = 10mA -1 VNOM 1 %
VOUT < 1.0V, IOUT = 10mA -10 10 mV
Line Regulation VINL = Max (VOUT + 0.5V, 3.6V) to 5.5V 0.5 mV
Load Regulation IOUT = 1mA to IMAX 0.1 V/A
Power Supply Rejection Ratio dB
Regulator Enabled 22
Supply Current per Output µA
Regulator Disabled 0 2
Soft-Start Period VOUT = 3.0V 100 µs
Power Good Threshold VOUT Rising 92 %
Power Good Hysteresis VOUT Falling 3.5 %
IOUT = 20mA, f = 10Hz to 100kHz, VOUT =
Output Noise 30 µVRMS
1.2V
Discharge Resistance LDO Disabled, DIS[ ] = 1 1.5 kΩ
LDO rated at 150mA (REG10)
Current Limit VOUT = 95% of regulation voltage 180 mA
LDO rated at 350mA (REG11 & REG12)

: Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the
regulation voltage (for 3.1V output voltage or higher).
: LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage.
Under heavy overload conditions the output current limit folds back by 50% (typ)

ACT8846
Rev 7.0 06-Dec-2017
LOW-POWER(ALWAYS-ON) LDO ELECTRICAL CHARACTERISTICS

(VINL1 = 3.6V, COUT13 = 1µF, TA = 25°C, unless otherwise specified.)

REG13 — VNOM = 1.8V

Output Voltage Accuracy -3 VNOM 3 %
Line Regulation VINL1 = Max (VOUT + 0.2V, 2.5V) to 5.5V 13 mV
Supply Current from VINL1 5 µA
Maximum Output current 50 mA
PWM LED DRIVER ELECTRICAL CHARACTERISTICS


Output Current 100% Duty Cycle 6 10 16 mA
Output Low Voltage Feed in with 6mA 0.35 V
Leakage Current Sinking from 5.5V source 1 µA
PWM Frequency FRE[2:0] = 000 0.25 Hz
PWM Duty Adjustment DUTY[3:0] = 0000 to 1111 6.26 100 %

ACT8846
Rev 7.0 06-Dec-2017
TYPICAL PERFORMANCE CHARACTERISTICS

(TA = 25°C, unless otherwise specified.)
VREF vs. Temperature Frequency vs. Temperature

2.360
ACT8846-001
1.204
ACT8846-002
2.340
1.200 2.320
Frequency (MHz)
2.300
1.196
VREF (V)
2.280
2.260
1.192
2.240
1.188 2.220
2.200
1.184
2.180
-40 -20 0 20 40 60 80 100 120 140 -40 -20 0 20 40 60 80 100 120 140
Temperature (°C) Temperature (°C)
Startup of VIN/OUT13 Startup of nPBIN/OUT5/nRSTO

ACT8846-003
ACT8846-004
CH1
CH1
CH2
CH2
CH3
CH1: VVIN, 2V/div CH1: VnPBIN, 2V/div

CH2: VOUT13, 1V/div CH2: VOUT5, 500mV/div
TIME: 500µs/div CH3: VnRSTO, 1V/div
TIME: 20ms/div
Startup of OUT4/OUT5/OUT11/OUT3/
OUT1/OUT2
ACT8846-005
CH1
CH2
CH3
CH4
CH5
CH6
CH1: VOUT4, 2V/div
CH2: VOUT5, 1V/div
CH3: VOUT11, 2V/div
CH4: VOUT3, 1V/div
CH5: VOUT1, 1V/div
CH6: VOUT2, 1V/div
TIME: 2ms/div

ACT8846
Rev 7.0 06-Dec-2017
TYPICAL PERFORMANCE CHARACTERISTICS CONT’D

Sleep of PWREN/OUT3 Shutdown of PWRHLD/OUT3/OUT2/OUT1
ACT8846-006
ACT8846-007
CH1
CH1
CH2
CH2
CH3
CH4
CH1: VPWREN, 2V/div CH1: VPWRHLD, 2V/div

CH2: VOUT3, 1VV/div CH2: VOUT3, 1V/div
TIME: 1ms/div CH3: VOUT2, 1V/div
CH4: VOUT1, 1V/div
TIME: 1ms/div
Shutdown of PWRHLD/OUT4/OUT5/OUT11 nPBIN and nPBSTAT

ACT8846-008
ACT8846-009
CH1
CH1
CH2
CH2
CH3
CH4
CH1: VPWRHLD, 2V/div CH1: VnPBIN, 2V/div

CH2: VOUT4, 2V/div CH2: VnPBSTAT, 2V/div
CH3: VOUT5, 1V/div TIME: 10ms/div
CH4: VOUT11, 2V/div
TIME: 1ms/div
Shutdown of PWRHOLD and nRSTO

ACT8846-010
CH1
CH2
CH1: VPWRHOLD, 2V/div

CH2: VnRSTO, 2V/div
TIME: 2ms/div

ACT8846
Rev 7.0 06-Dec-2017

REG1 Efficiency vs. Output Current REG2 Efficiency vs. Output Current
100
ACT8846-012
100
ACT8846-011
VOUT = 1.2V VOUT = 1.2V VIN = 3.6V
VIN = 3.6V
80 80
VIN = 5.0V VIN = 5.0V
Efficiency (%)
VIN = 4.0V
Efficiency (%)
60 60
VIN = 4.0V
40 40
20 20
0 0
0 1 10 100 1000 10000 0 1 10 100 1000 10000
Output Current (mA) Output Current (mA)
REG3 Efficiency vs. Output Current REG4 Efficiency vs. Output Current
100
ACT8846-014
ACT8846-013
VOUT = 1.1V VIN = 3.6V 100 VOUT = 1.1V

VIN = 3.6V
80 80
VIN = 5.0V
Efficiency (%)
VIN = 5.0V
Efficiency (%)
60 60
VIN = 4.0V
VIN = 4.0V
40 40
20 20
0 0
0 1 10 100 1000 10000 0 1 10 100 1000 10000

ACT8846
Rev 7.0 06-Dec-2017

REG5 VOUT vs. IOUT VOUT10 @ 150mA vs. Temperature

1.200
ACT8846-015
ACT8846-016
1.186
Dropout Voltage (V)
1.160
1.182
1.120
VOUT (V)
1.178
1.080
1.174
1.040
1.000 1.170
0 40 80 120 160 200 -40 -20 0 20 40 60 80 100 120 140
Output Current (mA) Temperature (°C)
REG5/6 Dropout Voltage vs. IOUT REG10 @ 10mA vs. Temperature

400
ACT8846-018
1.205
ACT8846-017
350
Dropout Voltage (mV)
1.200
300
250 1.195
VOUT (V)
200
1.190
150
100
1.185
50
0 1.180
0 50 100 150 200 250
-40 -20 0 20 40 60 80 100 120 140
Output Current (mA) Temperature (°C)
REG6 VOUT vs. IOUT REG7/8/9 Dropout Voltage vs. IOUT

1.200
ACT8846-019
ACT8846-020
400
Dropout Voltage (V)
1.160
300
1.120
200
1.080
1.040 100
1.000
0
0 40 80 120 160 200
0 50 100 150 200 250 300 350 400
Output Current (mA)
Output Current (mA)

ACT8846
Rev 7.0 06-Dec-2017

REG8 VOUT vs. IOUT REG10 Dropout Voltage vs. IOUT

250
ACT8846-022
1.900
ACT8846-021

200
Output Voltage (V)
1.860
1.820 150
1.780 100
1.740 50
1.700 0
0 50 100 150 200 250 300 350 0 50 100 150 200
REG11 Dropout Voltage vs. IOUT REG12 Dropout Voltage vs. IOUT
250 250
ACT8846-023
ACT8846-024
200 200
150 150
100 100
50 50
0 0
0 100 200 300 400
0 100 200 300 400
Output Current (mA)
Output Current (mA)
REG5 Output Voltage vs. Output Current REG6 Output Voltage vs. Output Current
1.040 1.240
ACT8846-025
ACT8846-026
1.020 1.220
Output Voltage (V)
Output Voltage (V)
1.000 1.200
0.980 1.180
0.960 1.160
0.940 1.140
0.920 1.120
0.900 1.100
0 40 80 120 160 200 0 40 80 120 160 200

ACT8846
Rev 7.0 06-Dec-2017

1.840 3.340
ACT8846-027
ACT8846-028
1.820 3.320
Output Voltage (V)
Output Voltage (V)

1.800 3.300
1.780 3.280
1.760 3.260
1.740 3.240
1.720 3.220
1.700 3.200
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
3.340
ACT8846-030
3.340
ACT8846-029
3.320 3.320
Output Voltage (V)
Output Voltage (V)
3.300 3.300
3.280 3.280
3.260 3.260
3.240 3.240
3.220 3.220
3.200 3.200
0 50 100 150 200 250 300 350 0 40 80 120 160 200
ACT8846-032
2.840
ACT8846-031
1.840
1.820 2.820
Output Voltage (V)
Output Voltage (V)
1.800 2.800
1.780 2.780
1.760 2.760
1.740 2.740
1.720 2.720
1.700 2.700
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350

ACT8846
Rev 7.0 06-Dec-2017
SYSTEM CONTROL INFORMATION

Interfacing with the Rockchip RK31x8 processors
The ACT8846 is optimized for the Rockchip between these devices benefits by doing so, both
RK31x8 processors, supporting both the power the ACT8846 pin names and the RK31x8
domains as well as the signal interface. The processors pin names are provided. When this is
following paragraphs describe how to design done, the RK31x8 pin names are located after the
ACT8846 with the RK31x8 processors. ACT8846 pin names, and are italicized and located
inside parentheses. For example, PWREN (GPIOX)
While the ACT8846 supports many possible refers to the logic signal applied to the ACT8846's
configurations for powering these processors, one PWREN input, identifying that it is driven from the
of the most common configurations is detailed in RK31x8's GPIOX output.
this datasheet. In general, this document refers to
the ACT8846 pin names and functions. However, in
cases where the description of interconnections
Table 1:
ACT8846 and Rockchip RK31x8 Power Domains
ACT8846 DEFAULT MAX POWER UP ON/OFF @
POWER DOMAIN TYPE
REGULATOR VOLTAGE CURRENT ORDER SLEEP
REG1 VCC_DDR Adjustable 1.5A 5 ON DC/DC Step Down
REG2 VDD_LOG 1.0V 2.8A 5 ON DC/DC Step Down
REG3 VDD_ARM 1.0V 2.8A 4 OFF DC/DC Step Down
REG4 VCC_IO 3.0V 1.5A 1 ON DC/DC Step Down
REG5 VDD_10 1.0V 150mA 2 ON Low-Noise LDO
REG6 VDD_JETTA1V2 1.2V 150mA / OFF Low-Noise LDO
REG7 VCC18_CIF 1.8V 350mA / OFF Low-Noise LDO
REG8 VCCA_33 3.3V 350mA / OFF Low-Noise LDO
REG9 VCC_TP 3.3V 350mA / OFF Low-Noise LDO
REG10 VCC_JETTA3V3 3.3V 150mA / OFF Low Input-Voltage LDO
REG11 VCC18_IO 1.8V 350mA 3 ON Low Input-Voltage LDO
REG12 VCC28_CIF 2.8V 350mA / OFF Low Input-Voltage LDO

REG13 VDD_RTC 1.8V 50mA 0 ON Always-ON LDO
Table 2:
ACT8846 and Rockchip RK31x8 Power Mode
Power Mode Control State Power Domain State Quiescent Current

PWRHLD is asserted, PWREN is
ALL ON All Regulators ON 0.6mA
asserted
PWRHLD is de-asserted, PWREN is REG13 is ON, all other regula-
SHUTDOWN 10µA
de-asserted, VINL2 > 2.6V tors are off.
PWRHLD is de-asserted, PWREN is
ALL OFF All regulators off. 5µA
de-asserted, VINL2 < 2.2V

ACT8846
Rev 7.0 06-Dec-2017
Table 3:
ACT8846 and RK31x8 Signal Interface
ACT8846 DIRECTION ROCKCHIP RK31X8
PWREN GPIO6_B1
SCL I2C1_SCL
SDA I2C1_SDA
VSELR2 GPIO0_D7
GPIO1/VSELR3 GPIO0_D6
nRSTO NPOR
nIRQ GPIO6_A4
nPBSTAT GPIO6_A2
PWRHLD GPIO6_B0
Note: Typical connections shown, actual connections may vary.
Control Signals WDSREN[ ] for properly shutdown sequence.

Long Press / Power-cycle:
Enable Inputs
The ACT8846 features a variety of control inputs, If the Manual Reset button is asserted for more
which are used to enable and disable outputs than 4s/10s, ACT8846 commences a power
depending upon the desired mode of operation. cycle routine in which case all regulators are turned
PWRHLD is a logic inputs, while nPBIN is a unique, off and then turned back on. A status bit, PCSTAT[
multi-function input. ], is set after the power cycle. The PCSTAT[ ] bit is
automatically cleared to 0 after read.
nPBIN Multi-Function Input
nPBSTAT Output
The ACT8846 features the nPBIN multi-function
pin, which combines system enable/disable control nPBSTAT is an open-drain output that reflects the
with a hardware reset function. Select either of the state of the nPBIN input; nPBSTAT is asserted low
two pin functions by asserting this pin, either whenever nPBIN is asserted, and is high-Z
through a direct connection to GA as Manual Reset otherwise. This output is typically used as an
input, or through a 50kΩ resistor to GA for 32ms to interrupt signal to the processor, to initiate a
enable the IC, or through a 50kΩ resistor to GA for software-programmable routine such as operating
10s to disable the IC, as shown in Figure 2. mode selection or to open a menu. Connect
nPBSTAT to an appropriate supply voltage through
Manual Reset Function a 10kΩ or greater resistor.
The second major function of the nPBIN input is to Figure 2:
provide a manual-reset input for the processor. To nPBIN Input
manually-reset the processor, drive nPBIN directly
to GA through a low impedance (less than 2.5kΩ).
An internal timer detects the duration of the MR
event:
INL2
Manual
Short Press / Soft-Reset: Reset
50kΩ Detect
nPBIN
If the Manual Reset button is asserted for less than Push-
4s/10s, ACT8846 commences a soft-reset Button
Detect
operation where nRSTO immediately asserts low, Push-Button Manual
then remains asserted low until the nPBIN input is Reset
de-asserted and the reset time-out period expires. VIO
A status bit, SRSTAT[ ] , is set after a soft-reset

nPBSTAT
event. The SRSTAT[ ] bit is automatically cleared to To CPU
0 after read. After Short Press, set WDSREN[ ] to 1
about 1s after nRSTO de-assert then clear ACT8846
: Only for ACT8846QM468 and ACT8846QM490-T.

: Soft-Reset function is disabled in ACT8846QM460 , ACT8846QM468 and ACT8846QM490.
: Only for ACT8846QM460.

ACT8846
Rev 7.0 06-Dec-2017
nRSTO Output completed, the system remains enabled after the

push-button is released as long as PWRHLD is
nRSTO is an open-drain output which asserts low asserted high. If the processor does not assert
upon startup or when manual reset is asserted via PWRHLD before the user releases the push-button,
the nPBIN input. When asserted on startup, nRSTO the boot-up sequence is terminated and all
remains low until reset time-out period expires. regulators are disabled. This provides protection
When asserted due to manual-reset, nRSTO against "false-enable", when the push-button is
immediately asserts low, then remains asserted low accidentally depressed, and also ensures that the
until the nPBIN input is de-asserted and the reset system remains enabled only if the processor
time-out period expires. successfully completes the boot-up sequence.
Connect a 10kΩ or greater pull-up resistor from As with the enable sequence, a typical disable
nRSTO to an appropriate voltage supply. sequence is initiated when the user presses the
push-button, which interrupts the processor via the
nIRQ Output nPBSTAT output. After system is turned on, the
nIRQ is an open-drain output that asserts low any processor may shut down the system by setting
time an interrupt is generated. Connect a 10kΩ or OFFSYSCLR[ ] to 1 then setting OFFSYS[ ] to 1, or
greater pull-up resistor from nIRQ to an appropriate by pulling PWRHLD to logic low. The user could
voltage supply. nIRQ is typically used to drive the force shut down ACT8846 anytime by pressing the
interrupt input of the system processor. power on push-button for 10 seconds even when
software crashes.
Many of the ACT8846's functions support interrupt-
generation as a result of various conditions. These SLEEP Mode Sequence
are typically masked by default, but may be The ACT8846 supports RK31x8 processor’s
unmasked via the I2C interface. For more SLEEP mode operation. Once a successful power-
information about the available fault conditions, up routine has been completed, SLEEP mode may
refer to the appropriate sections of this datasheet. be initiated through a variety of software-controlled
mechanisms.
Push-Button Control
The ACT8846 is designed to initiate a system SLEEP mode is typically initiated when the user
enable sequence when the nPBIN multi-function presses the push-button during normal operation.
input is asserted for 32ms. Once this occurs, a Pressing the push-button asserts the nPBIN input,
power-on sequence commences, as described which asserts the nPBSTAT output, which
below. The power-on sequence must complete and interrupts the processor. In response to this
the microprocessor must take control (by asserting interrupt the processor should disable REG6,
PWRHLD) before nPBIN is de-asserted. If the REG7, REG8, REG9, REG10 and REG12 via I2C,
microprocessor is unable to complete its power-up then de-assert PWREN(GPIO6_B1), disabling
routine successfully before the user releases the REG3. PWRHLD should remain asserted during
push-button, the ACT8846 automatically shuts the SLEEP mode so that REG1, REG2, REG4, REG5,
system down. This provides protection against and REG11 remain enabled.
accidental or momentary assertions of the push- The ACT8846 wakes up from SLEEP mode when
button. If desired, longer “push-and-hold” times can either the push-button and/or PWREN (GPIO6_B1)
be implemented by simply adding an additional time is asserted. In either case, REG3 is enable which
delay before asserting PWRHLD. allow the system to resume normal operation.
Control Sequences
The ACT8846 features a variety of control
sequences that are optimized for supporting system
enable and disable, as well as SLEEP mode of the
Rockchip RK31x8 processors.
Enabling/Disabling Sequence
A typical enable sequence is initiated whenever the
nPBIN is asserted low for 32ms via 50KΩ
resistance. The power control diagram is shown in
Figure 3. During the boot sequence, the
microprocessor must assert PWRHLD (GPIO6_B0)
to ensure that the system remains powered after
nPBIN is released. Once the power-up routine is
: Only for ACT8846QM468.

ACT8846
Rev 7.0 06-Dec-2017
Watch-Dog Supervision ACT8846 supports software-initiated power cycle.

Once the SIPC[ ] bit is set, the PMU waits for 8ms
The ACT8846 features a watchdog supervisory and then initiate a power cycle to restart the entire
function. An internal watchdog timer of 4s is system.
unmasked by setting either WDSREN[ ] or
WDPCEN [ ] bit to one. Once enabled, the
watchdog timer is reset whenever there is I2C
activity for the PMU. In the case where the system
software stops responding and that there is no I2C
transactions for 4s, the watchdog timer expires. As
a result, the PMU either perform a soft-reset or
power cycle, depending on whether WDSREN [ ] or
WDPCEN [ ] is set.
Software-Initiated Power Cycle
Figure 3:
ACT8846QM460 and ACT8846QM468 Power Control Sequence
Sleep/Wakeup Power off
Power on Sequence
Sequence Sequence
UVLO
Main Battery
OUT13
nPBIN
2ms
93% of VOUT4
OUT4
2ms
93% of VOUT5
OUT5
2ms
93% of VOUT11
OUT11
2ms
93% of VOUT3
OUT3 2ms
OUT1, OUT2
PWREN
100ms
nRSTO
PWRHLD
: Watch-Dog is not supported in ACT8846QM468 and ACT8846QM490-T .

ACT8846
Rev 7.0 06-Dec-2017
Figure 3A:
ACT8846QM490 Power Control Sequence for RK3288
Power off
Power on Sequence
Sequence
UVLO
Main Battery
OUT13
nPBIN
2ms
93% of VOUT4
OUT4
1ms
93% of VOUT10
OUT10
1ms
93% of VOUT1
OUT1
1ms
93% of VOUT3
OUT3 1ms
93% of VOUT11
OUT11 1ms
93% of VOUT9
OUT9
1ms
93% of VOUT5
OUT2 OUT5
PWREN
100ms
nRSTO
PWRHLD

ACT8846
Rev 7.0 06-Dec-2017
FUNCTIONAL DESCRIPTION
I2C Interface
The ACT8846 features an I2C interface that allows Thermal Protection
advanced programming capability to enhance overall
system performance. To ensure compatibility with a BATLEV[3:0] BATLEV Falling
wide range of system processors, the I2C interface Threshold
supports clock speeds of up to 400kHz (“Fast-Mode”
operation) and uses standard I2C commands. I2C 0000 2.5
write-byte commands are used to program the 0001 2.6
ACT8846, and I2C read-byte commands are used to
read the ACT8846’s internal registers. The ACT8846 0010 2.7
always operates as a slave device, and is addressed
using a 7-bit slave address followed by an eighth bit, 0011 2.8
which indicates whether the transaction is a read- 0100 2.9
operation or a write-operation, [1011010x].
SDA is a bi-directional data line and SCL is a clock 0101 3.0
input. The master device initiates a transaction by 0110 3.1
issuing a START condition, defined by SDA
transitioning from high to low while SCL is high. Data 0111 3.2
is transferred in 8-bit packets, beginning with the
MSB, and is clocked-in on the rising edge of SCL. 1000 3.3
Each packet of data is followed by an “Acknowledge” 1001 3.4
(ACK) bit, used to confirm that the data was
transmitted successfully. 1010 3.5
2
For more information regarding the I C 2-wire serial 1011 3.6
interface, go to the NXP website: http://www.nxp.com.
1100 3.7
Housekeeping Functions
1101 3.8
Programmable battery Voltage Monitor
The ACT8846 features a programmable battery- 1110 3.9
voltage monitor, which monitors the voltage at INL2 1111 4.0
(which should be connected directly to the battery)
and compares it to a programmable threshold
voltage. The VBATMON comparator is designed to The ACT8846 integrates thermal shutdown
be immune to noise resulting from switching, load protection circuitry to prevent damage resulting
transients, etc. The BATMON comparator is disable from excessive thermal stress, as may be
by default; to enable it, set the BATLEV[3:0] register encountered under fault conditions.
to one of the value in Table 4. Note that there is a
200mV hysteresis between the rising and falling Thermal Interrupt
threshold for the comparator. The VBATDAT [-] bit If the thermal interrupt is unmasked (by setting
reflects the output of the BATMON comparator. The nTMSK[ ] to 1), ACT8846 can generate an interrupt
value of VBATDAT[ ] is 1 when VINL2 < BATLEV; when the die temperature reaches 120°C (typ).
value is 0 otherwise.
The VBATMON comparator can generate an Thermal Protection
interrupt when VINL2 is lower than BATLEV[ ] voltage. If the ACT8846 die temperature exceeds 160°C, the
The interrupt is masked by default by can be thermal protection circuitry disables all regulators
unmasked by setting VBATMSK[ ] = 1. and prevents the regulators from being enabled until
the IC temperature drops by 20°C (typ).
Table 4:
BATLEV Falling Threshold

ACT8846
Rev 7.0 06-Dec-2017
STEP-DOWN DC/DC REGULATORS

General Description induced upon the voltage source. A 10μF ceramic
capacitor is recommended for each regulator in most
REG1, REG2, REG3, and REG4 are fixed-frequency, applications.
current-mode, synchronous PWM step-down
converters that achieves peak efficiencies of up to Output Capacitor Selection
97%. These regulators operate with a fixed frequency
of 2.25MHz, minimizing noise in sensitive REG1, REG2, REG3, and REG4 were designed to
applications and allowing the use of small external take advantage of the benefits of ceramic capacitors,
components. Additionally, REG1, REG2, REG3, and namely small size and very-low ESR. REG1, REG2,
REG4 are available with a variety of standard and REG3 and REG4 are designed to operate with 33uF
custom output voltages, and may be software- or 44uF output capacitor over most of their output
controlled via the I2C interface for systems that voltage ranges, although more capacitance may be
require advanced power management functions. desired depending on the duty cycle and load step
requirements.
100% Duty Cycle Operation Two of the most common dielectrics are Y5V and
REG1, REG2, REG3, and REG4 are capable of X5R. Whereas Y5V dielectrics are inexpensive and
operating at up to 100% duty cycle. During 100% can provide high capacitance in small packages, their
duty cycle operation, the high-side power MOSFETs capacitance varies greatly over their voltage and
are held on continuously, providing a direct temperature ranges and are not recommended for
connection from the input to the output (through the DC/DC applications. X5R and X7R dielectrics are
inductor), ensuring the lowest possible dropout more suitable for output capacitor applications, as
voltage in battery powered applications. their characteristics are more stable over their
operating ranges, and are highly recommended.
Operating Mode
Inductor Selection
By default, REG1, REG2, REG3, and REG4 operate
in fixed-frequency PWM mode at medium to heavy REG1, REG2, REG3, and REG4 utilize current-mode
loads, then transition to a proprietary power-saving control and a proprietary internal compensation
mode at light loads in order to save power. scheme to simultaneously simplify external
component selection and optimize transient
Synchronous Rectification performance over their full operating range. These
devices were optimized for operation with 2.2μH or
REG1, REG2, REG3, and REG4 each feature 1μH inductors. Choose an inductor with a low DC-
integrated synchronous rectifiers, maximizing resistance, and avoid inductor saturation by choosing
efficiency and minimizing the total solution size and inductors with DC ratings that exceed the maximum
cost by eliminating the need for external rectifiers. output current by at least 30%.
Soft-Start
Configuration Options
REG1, REG2, REG3, and REG4 include internal 400
us soft-start ramps which limit the rate of change of Output Voltage Programming
the output voltage, minimizing input inrush current Figure 4:
and ensuring that the output powers up in a
monotonic manner that is independent of loading on OUT1 Output Voltage Programming
the outputs. This circuitry is effective any time the
regulator is enabled, as well as after responding to a
short-circuit or other fault condition.
Compensation
REG1, REG2, REG3, and REG4 utilize current-mode
control and a proprietary internal compensation OUT1
scheme to simultaneously simplify external
component selection and optimize transient
performance over their full operating range. No ACT8846 CFF RFB1
compensation design is required; simply follow a few
simple guide lines described below when choosing FB1
external components.
RFB2
Input Capacitor Selection
The input capacitor reduces peak currents and noise

ACT8846
Rev 7.0 06-Dec-2017
Figure 4 shows the feedback network necessary to If a DC/DC's nFLTMSK[-] bit is set to 1, the ACT8846
set the output voltage for REG1 when using the will interrupt the processor if that DC/DC's output
adjustable output voltage option. Connect the FB1 voltage falls below the power-OK threshold. In this
pin to the output directly to regulate the output case, nIRQ will assert low and remain asserted until
voltage at 1.2V. Select components as follows: Set either the regulator is turned off or back in regulation,
RFB2 = 51kΩ, then calculate RFB1 using the and the OK[ ] bit has been read via I2C.
following equation:
PCB Layout Considerations
V 
RFB1  RFB 2  OUT 1  1  (1) High switching frequencies and large peak currents
 FB1
V  make PC board layout an important part of step-down
DC/DC converter design. A good design minimizes
where VFB1 is 1.2V. Finally choose CFF using the excessive EMI on the feedback paths and voltage
following equation: gradients in the ground plane, both of which can
result in instability or regulation errors.
1  10 6
CFF  (2) Step-down DC/DCs exhibit discontinuous input
RFB1 current, so the buck input capacitors must be placed
By default, REG2, REG3 and REG4 power up and as close as possible to the IC. Connect the
regulate to their default output voltages. For REG2, capacitors directly to the corresponding VPx input pin
REG3 and REG4, the output voltage is selectable by and Gx power ground pin. Avoid the use of vias. Best
setting corresponding VSELR# pin that when performance is achieved by direct input capacitor
VSELR# is low, output voltage is programmed by connection to the IC and by routing the SWx trace on
VSET0[ ] bits, and when VSELR# is high, output the top layer, directly under the input capacitor. The
voltage is programmed by VSET1[ ] bits. Also, once inductor, input filter capacitor, and output filter
the system is enabled, each regulator's output capacitor should be connected as close together as
voltage may be independently programmed to a possible, with short, direct, and wide traces. The
different value. Program the output voltages via the ground nodes for each regulator's power loop should
I2C serial interface by writing to the regulator's be connected at a single point in a star-ground
VSET0[ ] register if VSELR# is low or VSET1[ ] configuration, and this point should be connected to
register if VSELR# is high as shown in Table 5. the backside ground plane with multiple via. The
output node for each regulator should be connected
Enable / Disable Control to its corresponding OUTx pin through the shortest
During normal operation, each buck may be enabled possible route, while keeping sufficient distance from
or disabled via the I2C interface by writing to that switching nodes to prevent noise injection. Finally,
regulator's ON[ ] bit. the exposed pad should be directly connected to the
backside ground plane using multiple via to achieve
OK[ ] and Output Fault Interrupt low electrical and thermal resistance.
Each DC/DC features a power-OK status bit that can
be read by the system microprocessor via the I2C
interface. If an output voltage is lower than the power-
OK threshold, typically 7% below the programmed
regulation voltage, that regulator's OK[ ] bit will be 0.
Table 5:
REGx/VSET[ ] Output Voltage Setting
REGx/VSET[5:3]
REGx/VSET[2:0]
000 001 010 011 100 101 110 111
000 0.600 0.800 1.000 1.200 1.600 2.000 2.400 3.200
001 0.625 0.825 1.025 1.250 1.650 2.050 2.500 3.300
010 0.650 0.850 1.050 1.300 1.700 2.100 2.600 3.400
011 0.675 0.875 1.075 1.350 1.750 2.150 2.700 3.500
100 0.700 0.900 1.100 1.400 1.800 2.200 2.800 3.600
101 0.725 0.925 1.125 1.450 1.850 2.250 2.900 3.700
110 0.750 0.950 1.150 1.500 1.900 2.300 3.000 3.800
111 0.775 0.975 1.175 1.550 1.950 2.350 3.100 3.900

ACT8846
Rev 7.0 06-Dec-2017
LOW-NOISE, LOW-DROPOUT LINEAR REGULATORS

General Description Each of the LDOs features an optional output
discharge function, which discharges the output to
ACT8846 features eight low-noise, low-dropout ground through a 1.5kΩ resistance when the LDO is
linear regulators (LDOs) that supply up to 350mA. disabled. This feature may be enabled or disabled
Three of these LDOs (REG10, REG11, and by setting DIS[-]; set DIS[-] to 1 to enable this
REG12) supports extended input voltage range function, clear DIS[-] to 0 to disable it.
down to 1.7V. Each LDO has been optimized to
achieve low noise and high-PSRR. OK[ ] and Output Fault Interrupt
Output Current Limit Each LDO features a power-OK status bit that can
be read by the system microprocessor via the
Each LDO contains current-limit circuitry featuring a interface. If an output voltage is lower than the
current-limit fold-back function. During normal and power-OK threshold, typically 11% below the
moderate overload conditions, the regulators can programmed regulation voltage, the value of that
support more than their rated output currents. regulator's OK[-] bit will be 0.
During extreme overload conditions, however, the
current limit is reduced by approximately 30%, If a LDO's nFLTMSK[-] bit is set to 1, the ACT8846
reducing power dissipation within the IC. will interrupt the processor if that LDO's output
voltage falls below the power-OK threshold. In this
Compensation case, nIRQ will assert low and remain asserted until
either the regulator is turned off or back in
The LDOs are internally compensated and require regulation, and the OK[-] bit has been read via I2C.
very little design effort, simply select input and
output capacitors according to the guidelines below. PCB Layout Considerations
Input Capacitor Selection The ACT8846’s LDOs provide good DC, AC, and
noise performance over a wide range of operating
Each LDO requires a small ceramic input capacitor conditions, and are relatively insensitive to layout
to supply current to support fast transients at the considerations. When designing a PCB, however,
input of the LDO. Bypassing each INL pin to GA careful layout is necessary to prevent other circuitry
with 1μF. High quality ceramic capacitors such as from degrading LDO performance.
X7R and X5R dielectric types are strongly
recommended. A good design places input and output capacitors
as close to the LDO inputs and output as possible,
Output Capacitor Selection and utilizes a star-ground configuration for all
Each LDO requires a small 2.2μF ceramic output regulators to prevent noise-coupling through
capacitor for stability . For best performance, each ground. Output traces should be routed to avoid
output capacitor should be connected directly close proximity to noisy nodes, particularly the SW
between the output and GA pins, as close to the nodes of the DC/DCs.
output as possible, and with a short, direct REFBP is a noise-filtered reference, and internally
connection. High quality ceramic capacitors such as has a direct connection to the linear regulator
X7R and X5R dielectric types are strongly controller. Any noise injected onto REFBP will
recommended. directly affect the outputs of the linear regulators,
and therefore special care should be taken to
Configuration Options ensure that no noise is injected to the outputs via
Output Voltage Programming REFBP. As with the LDO output capacitors, the
REFBP bypass capacitor should be placed as close
By default, each LDO powers up and regulates to to the IC as possible, with short, direct connections
its default output voltage. Once the system is to the star-ground. Avoid the use of via whenever
enabled, each output voltage may be independently possible. Noisy nodes, such as from the DC/DCs,
programmed to a different value by writing to the should be routed as far away from REFBP as
regulator's VSET[-] register via the I2C serial possible.
interface as shown in Table 5.
Enable / Disable Control
During normal operation, each LDO may be
enabled or disabled via the I2C interface by writing
to that LDO's ON[ ] bit.
Output Discharge

ACT8846
Rev 7.0 06-Dec-2017
ALWAYS-ON LDO (REG13)

General Description
REG13 is an always-on, low-dropout linear
regulator (LDO) that is optimized for RTC and
backup-battery applications. REG13 features low-
quiescent supply current, current-limit protection,
and reverse-current protection, and is ideally suited
for always-on power supply applications, such as
for a real-time clock, or as a backup-battery or
super-cap charger.
Reverse-Current Protection
REG13 features internal circuitry that limits the
reverse supply current to less than 1µA when the
input voltage falls below the output voltage, as can
be encountered in backup-battery charging
applications. REG13's internal circuitry monitors the
input and the output, and disconnects internal
circuitry and parasitic diodes when the input voltage
falls below the output voltage, greatly minimizing
backup battery discharge.
Typical Application
Voltage Regulators
REG13 is ideally suited for always-on voltage-
regulation applications, such as for real-time clock
and memory keep-alive applications. This regulator
requires only a small ceramic capacitor with a
minimum capacitance of 0.47μF for stability. For
best performance, the output capacitor should be
connected directly between the output and GA, with
a short and direct connection.
Figure 5:
Typical Application of RTC LDO
Backup Battery Charging
ACT8846 OUT13
RTC
Supper cap or
Back- up battery
REG13 features a constant current-limit, which

protects the IC under output short-circuit conditions
as well as provides a constant charge current, when
operating as a backup battery charger.

ACT8846
Rev 7.0 06-Dec-2017
PWM LED DRIVERS

The GPIO3, the GPIO4, the GPIO5, and the GPIO6 DUTY#[ ] PWM Frequency Setting
are configured as PWM LED drivers, which could
support up to 6mA current with programmable
frequency and duty cycle. Set PWM#EN[ ] bit to “1” DUTY#[3:0] PWM Duty Cycle [%]
to enable PWM function of GPIO#.
0000 6.25
PWM Frequence Selection 0001 12.5
Each LED driver may be independently 0010 18.75
programmed to a different frequency by writing to
the GPIO’s FRE[2:0] register via the I2C serial 0011 25
0100 31.25
Table 6:
0101 37.5
FRE#[ ] PWM Frequency Setting
0110 43.75
0111 50
FRE#[2:0] PWM Frequency [Hz]
1000 56.25
000 0.25
1001 62.5
001 0.5
1010 68.75
010 1
1011 75
011 2
1100 81.25
100 128
1101 87.5
101 256
1110 93.75
PWM Duty Cycle Selection 1111 100
Each LED driver may be independently
programmed to a different duty cycle by writing to
the GPIO’s DUTY[3:0] register via the I2C serial
Table 7:
ACT8846
Rev 7.0 06-Dec-2017
CMI OPTIONS
CMI 106: ACT8846QM106
Rail VSET0 VSET1 Sequencing StartUp Soft-

Voltage Volt- Input Trigger Delay Start
(V) age (V) (us) (us)
OUT1 1.2 1.2 OUT2 2000 400

OUT2 0.95 0.95 Vin UVLO 0 400
OUT3 3.3 3.3 OUT1 2000 400
OUT4 1.8 1.8 Vin UVLO 0 400
OUT5 1.8 n/a Vin UVLO 0 140
OUT6 1.8 n/a OUT1 2000 140
OUT7 3.3 n/a Vin UVLO 0 140
2
OUT8 1.2 n/a IC 0 140
OUT9 2.8 n/a I 2C 0 140
2
OUT10 1.5 n/a IC 0 100
OUT11 2.8 n/a I 2C 0 100
2
OUT12 1.8 n/a IC 0 100
OUT13 1.8 n/a I 2C 0 100
Hardware Configuration
PWRHLD and PWREN must be connected together in CMI 106.
Startup
The ACT8846QM106-T has two startup sequences. The first is pushbutton startup. Asserting nPBIN low
starts the startup sequence. nPBIN must stay low until after PWRHLD and PWREN are asserted high by
an external source, usually a uP. If nPBIN goes high before PWRHLD goes high, the IC shuts down all
outputs. The second startup sequence is with the PWREN and PWRHLD pins. After input power is ap-
plied, asserting PWREN high starts the startup sequence. Note that nPBIN should stay high in this appli-
CMI 106 Startup with PWRHLD

UVLO
VIN
PWRHLD and PWREN
nPBIN
OUT2/4/5/7
2ms
OUT1
2ms
40ms
OUT3/6
nRSTO

ACT8846
Rev 7.0 06-Dec-2017
CMI 106: ACT8846QM106 continued.
CMI 106 Startup with nPBIN

UVLO
VIN
PWRHLD and PWREN
nPBIN
32ms
OUT2/4/5/7
2ms
OUT1
2ms
40ms
OUT3/6
nRSTO
Shutdown
The IC can be turned off by pulling nPBIN low through a 50kohm resistor to GA or by deasserting
PWREN and PWRHLD pins low. The IC can also be turned off via I2C.
PWREN
Asserting PWREN high enables the IC. In pushbutton applications, if PWREN is not asserted high before
the nPBIN pin goes high, the IC shuts down. Note that PWREN and PWRHLD must be connected togeth-
er.
nPBIN
nPBIN retains the short and long press functionality described earlier in the datasheet.
NRSTO
nRSTO is gated by OUT6 and OUT7 and has a 40ms delay.
DVS
DVS functionality is only available via I2C.
VSELR/GPIO1/GPIO2
The VSELR/GPIO1/GPIO2 pins are not functional and should be permanently pulled high or low.
GPIO1/2/3/4/5/6
These outputs are off by default but can be enabled via I 2C. GPIO3 frequency and duty cycle are 256Hz
and 50%. GPIO4/5/6 frequency and duty cycle are 0.25Hz and 6.25%.
Watchdog
All watchdog functionality is disabled by default.

ACT8846
Rev 7.0 06-Dec-2017
CMI 107: ACT8846QM107

CMI107 is optimized to power the Cortex A7 processor.
Sequencing
Rail VSET0 VSET1 Sequencing StartUp Soft-

Voltage Volt- Input Trigger Delay Start
(V) age (V) (us) (us)
OUT1 1.8 1.8 OUT7 0 400

OUT2 0.9 0.9 GPIO1 500 400
OUT3 1.2 1.2 OUT11 500 400
OUT4 3.0 3.0 I 2C 0 400
2
OUT5 3.3 n/a IC 0 140
2
OUT6 1.8 n/a IC 0 140
OUT7 1.8 n/a OUT2 500 140
OUT8 3.3 n/a OUT3 500 140
OUT9 3.3 n/a OUT8 1000 140
OUT10 3.3 n/a OUT8 500 100
OUT11 2.5 n/a OUT1 500 100
OUT12 3.3 n/a I 2C 0 100
OUT13 1.8 n/a Always On 0 100
Hardware Configuration
PWRHLD and PWREN must be connected together in CMI 107.
GPIO1 must be directly connected to OUT13 in CMI 107.
Startup
The ACT8846QM107-T has two startup sequences. The first is pushbutton startup. Asserting nPBIN low
starts the startup sequence. nPBIN must stay low until after PWRHLD and PWREN are asserted high by
an external source, usually a uP. If nPBIN goes high before PWRHLD goes high, the IC shuts down all
outputs. The second startup sequence is with the PWREN and PWRHLD pins. After input power is ap-
plied, asserting PWREN high starts the startup sequence. Note that nPBIN should stay high in this appli-
cation. In both startup conditions, OUT4/5/6/12 are off by default, but can be enabled via I 2C

ACT8846
Rev 7.0 06-Dec-2017
CMI 107: ACT8846QM107 continued
CMI 107 Startup with PWRHLD

VIN
PWRHLD and PWREN
nPBIN
OUT13 / GPIO1 0.5ms
OUT2 0.5ms
OUT7
OUT1 0.5ms
OUT11 0.5ms
OUT3 0.5ms
OUT8
1ms
OUT10 0.5ms
OUT9 40ms
nRSTO
Shutdown
The IC can be turned off by pulling nPBIN low through a 50kohm resistor to GA or by deasserting PWREN
and PWRHLD pins low. The IC can also be turned off via I2C.
PWREN
Asserting PWREN high enables the IC. In pushbutton applications, if PWREN is not asserted high before
the nPBIN pin goes high, the IC shuts down. Note that PWREN and PWRHLD must be connected together.
nPBIN
nPBIN retains the short and long press functionality described earlier in the datasheet.
NRSTO
nRSTO is gated by OUT9 and has a 40ms delay.
DVS
DVS functionality is only available via I2C.
VSELR/GPIO1/GPIO2
The VSELR/GPIO1/GPIO2 pins are not functional and should be permanently pulled high or low.
GPIO1/2/3/4/5/6
These outputs are off by default but can be enabled via I 2C. GPIO3 frequency and duty cycle are 256Hz
and 50%. GPIO4/5/6 frequency and duty cycle are 0.25Hz and 6.25%.
Watchdog
All watchdog functionality is disabled by default.

ACT8846
Rev 7.0 06-Dec-2017
ERRATA INFO
Errata Name:
ACT8846 creates I2C BUS contention.
Description:
ACT8846 incorrectly detects its I2C slave
address and pulls SDA low to acknowledge the
address. This occurs under several conditions.
1. The IC is on a multi-slave I2C bus and the
other slaves use multi-byte read or write
commands, and the read/write data contains a
string of bits that match the ACT8846 I2C
address.
2. The host addresses a device with a 10 bit I2C
address that contains a string of bits that match
the ACT8846 I2C address.
Work Around:
This issue has several work arounds.
1. Do not put I2C devices that use multi-byte
read or write commands on the ACT8846 I2C
bus.
2. Disable the ACT8846 I2C communication after
power up and before using any multi-byte read
or write commands. This allows the user to do a
one-time reconfiguration of the ACT8846 after
power up. Disabling ACT8846 I2C
communication reconfigures SDA and SCL high-
impedance digital inputs. Because the specific
commands to disable the I2C bus are CMI
specific, please contact the factory for specific
instructions.

ACT8846
Rev 7.0 06-Dec-2017
TQFN66-48 PACKAGE OUTLINE AND DIMENSIONS
D DIMENSION IN DIMENSION IN
D/2 SYMBOL MILLIMETERS INCHES
MIN MAX MIN MAX
A 0.700 0.800 0.032 0.036
E/2 A1 0.200 REF 0.008 REF
A2 0.000 0.050 0.000 0.002
E b 0.150 0.250 0.006 0.010
D 6.00 0.24
E 6.00 0.24
D2 4.15 4.40 0.166 0.176
E2 4.15 4.40 0.166 0.176
e 0.400 BSC 0.016 BSC

L 0.300 0.500 0.012 0.020
R 0.300 0.012
A
A1
A2
D2
b
L
E2


ACT8846 Datasheet

Uploaded by

Copyright:

Available Formats

ACT8846 Datasheet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ACT8846 Datasheet

Uploaded by

Copyright:

Available Formats

ACT8846 Rev 7.

Advanced PMU for Multi-core Application Processors

FEATURES GENERAL DESCRIPTION

Innovative PowerTM -1- www.active-semi.com

FUNCTIONAL BLOCK DIAGRAM

GPIO2 REG9 OUT9

GPIO4 INL3 To Battery

GPIO6 REG10 OUT10

Innovative PowerTM -2- www.active-semi.com

PACKAGE PINS TEMPERATURE RANGE

TQFN66-48 48 -40°C to +85°C

Innovative PowerTM -3- www.active-semi.com

OUT11 ACTIVE PWRHLD

Thin - QFN (TQFN66-48)

Innovative PowerTM -4- www.active-semi.com

1, 2 SW3 Switch Node for REG3.

4 OUT10 REG10 output. Bypass it to ground with a 2.2µF capacitor.

5 OUT11 REG11 output. Bypass it to ground with a 2.2µF capacitor.

6 INL3 Power input for REG10, REG11 and REG12.

7 OUT12 REG12 output. Bypass it to ground with a 2.2µF capacitor.

Active-Low Open-Drain Push-Button Status Output. nPBSTAT is asserted low

11, 12 SW2 Switch Node for REG2.

15 OUT2 Output Voltage Sense for REG2.

18 INL2 Power Input for REG8, REG9.

19 OUT9 REG9 output. Bypass it to ground with a 2.2µF capacitor.

21 OUT4 Output voltage sense for REG4.

22 OUT8 REG8 output. Bypass it to ground with a 2.2µF capacitor.

24 SCL Clock Input for I2C Serial Interface.

Innovative PowerTM -5- www.active-semi.com

PIN DESCRIPTIONS CONT’D

: Only for ACT8846QM468.

Innovative PowerTM -6- www.active-semi.com

ABSOLUTE MAXIMUM RATINGS

OUT10, OUT11, OUT12 to GA -0.3 to INL3 + 0.3 V

Innovative PowerTM -7- www.active-semi.com

I2C INTERFACE ELECTRICAL CHARACTERISTICS

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

tST tHD tSU tSP

Innovative PowerTM -8- www.active-semi.com

GLOBAL REGISTER MAP

: Default values of ACT8846QM468-T.

Innovative PowerTM -9- www.active-semi.com

GLOBAL REGISTER MAP CONT’D

: Default values of ACT8846QM468-T.

Innovative PowerTM - 10 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS

REG3 0x30 [7:6] - R Reserved.

Primary Output Voltage Selection. Valid when VSEL is driven

Innovative PowerTM - 11 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS CONT’D

Innovative PowerTM - 12 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS CONT’D

Innovative PowerTM - 13 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS CONT’D

Innovative PowerTM - 14 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS CONT’D

Innovative PowerTM - 15 - www.active-semi.com

REGISTER AND BIT DESCRIPTIONS CONT’D

Innovative PowerTM - 16 - www.active-semi.com