Cover & Table of Contents - Structural Detailing in Concrete (2nd Edition)

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

Structural detailing in concrete

2nd edition

A comparative study of British, European


and American codes and practices

M. Y. H. Bangash
Published by Thomas Telford Publishing, Thomas Telford Ltd, 1 Heron Quay,
London E14 4JD.
URL: http://www.thomastelford.com

Distributors for Thomas Telford books are


USA: ASCE Press, 1801 Alexander Bell Drive, Reston, VA 20191-4400,
USA
Japan: Maruzen Co. Ltd, Book Department, 3–10 Nihonbashi 2-chome,
Chuo-ku, Tokyo 103
Australia: DA Books and Journals, 648 Whitehorse Road, Mitcham 3132,
Victoria

First published by Blackwell Scientific Publications, 1992


Second edition 2003

A catalogue record for this book is available from the British Library

ISBN: 0 7277 3034 7

© M. Y. H. Bangash, 2003

All rights, including translation, reserved. Except as permitted by the


Copyright, Designs and Patents Act 1988, no part of this publication may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means, electronic, mechanical, photocopying or otherwise, without the prior
written permission of the Books Publisher, Thomas Telford Publishing,
Thomas Telford Ltd, 1 Heron Quay, London E14 4JD.

This book is published on the understanding that the author is solely


responsible for the statements made and opinions expressed in it and that its
publication does not necessarily imply that such statements and/or opinions
are or reflect the views or opinions of the publishers. While every effort has
been made to ensure that the statements made and the opinions expressed in
this publication provide a safe and accurate guide, no liability or responsibility
can be accepted in this respect by the authors or publishers.

Typeset by APEK Digital Imaging, Bristol


Printed and bound in Great Britain by MPG Books, Bodmin, Cornwall
Contents

Preface iv

Acknowledgements vi

Metric conversions vii

I. General requirements for structural detailing in concrete 1


I.1 Introduction 1
I.2 Drafting practice based on British codes 1
I.2.1 Drawing instruments 2
I.2.2 Linework and dimensioning 2
I.2.3 Grids and levels 2
I.2.4 Sections and elevation marker 4
I.2.5 Symbols and abbreviations 4
I.2.6 Holes, pockets, recesses, nibs and kerbs (curbs) 5
I.3 Drafting practice based on Eurocode 2 7
I.4 Drafting practice based on American codes 12
I.4.1 Drawing preparation 14
I.5 Holes, pockets, recesses, nibs and kerbs (curbs) – based on 19
Eurocode 2
I.6 Reinforcement size, cover, spacings and dimensional tolerance 20
I.6.1 British practice 20
I.6.2 Eurocode 2 DD ENV 1992-1-1: 1992 22
I.7 ACI/ASTM/ASCE and American practices 27
I.7.1 Cover and spacings 29
I.8 Steel fabric for reinforcement of concrete 29
I.8.1 British practice BS 4483 (1998) 29
I.9 Bar shape codes 33
I.9.1 British practice: BS 4449, BS 4482, BS 4483 and 33
BS 6744
I.9.2 European practice and Eurocode 2 46
I.9.3 American standards: ACI and ASTM and state’s 55
practices

II. Reinforced concrete beams and slabs 65


II.1 Reinforced concrete beams 65
II.1.1 Detailing based on British codes and practices 66
II.1.2 Detailing based on Eurocode 2 and European 77
practices
II.1.3 Detailing based on American practices 88
II.2 Reinforced concrete slabs 95
II.2.1 Slab reinforcement and method of detailing based 95
on British Standard Code BS 8110
II.2.2 Slab reinforcement and method of detailing based 110
on Eurocode 2
II.2.3 Slab reinforcement and method of detailing based 115
on ACI, ASCE and other state’s practices

iii
STRUCTURAL DETAILING IN CONCRETE

III. Stairs and staircases 121


III.1 Stairs and their types 121
III.1.1 Specifications and basic data on staircases 121
III.1.2 Stairway layouts 125
III.1.3 Additional basic layouts and data 125

IV. Columns, frames and walls 146


IV.1 Columns 146
IV.1.1 Introduction 146
IV.1.2 Column detailing based on British codes 146
IV.1.3 Wall detailing based on British codes 154
IV.1.4 Portals and frames 162
IV.2 Column, wall and frame detailing based on Eurocode 2 168
IV.2.1 Introduction 168
IV.2.2 Columns 168
IV.2.3 Walls 172
IV.2.4 Frames 175
IV.3 Column, wall and frame detailing based on the American 178
Concrete Institute codes
IV.3.1 Introduction 178
IV.3.2 Columns 178
IV.3.3 Reinforced concrete walls 181
IV.3.4 Reinforced concrete frames 184

V. Prestressed concrete 186


V.1 General introduction 186
V.2 Prestressing systems, tendon loads and material properties 201
V.2.1 Available systems 201
V.3 Structural detailing of prestressed concrete structures 201
V.3.1 Detailing based on British codes 201
V.3.2 Detailing based on Eurocode 2 206
V.3.3 Detailing based on ACI and PCI codes and other 212
American practices

VI. Composite construction, precast concrete elements, joints and 215


connections
VI.1 Composite construction and precast elements 215
VI.2 Joints and connections 224

VII. Concrete foundations and earth-retaining structures 235


VII.1 General introduction 235
VII.2 Types of foundations 235
VII.2.1 Isolated spread foundation, pad footing and 235
combined pad foundations
VII.2.2 Cantilever, balanced and strip foundations 237
VII.2.3 Circular and hexagonal footings 240
VII.3 Pile foundations 250
VII.3.1 Types of concrete piles 259
VII.3.2 Precast piles 259
VII.3.3 Square and octagonal piles 259
VII.3.4 Hollow cylindrical piles 260
VII.3.5 Cast-in-place piles 260
VII.3.6 Framed foundations for high-speed machinery 260
VII.3.7 Special considerations in planning 265
VII.3.8 Turbine pedestal using American practice 265

iv
PREAMBLE

VII.4 Well foundations and caissons 265


VII.4.1 Caissons 267
VII.5 Raft foundations 270
VII.6 Ground and basement floor foundations 272
VII.7 Earth-retaining structures 276
VII.7.1 Retaining structures based on ENV 1997-1 (1994) 276
VII.7.2 Limit states 276
VII.7.3 Actions, geometrical data and design situations 280
VIII. Special structures: case studies 285
VIII.1 Bridges 286
VIII.1.1 General introduction to types of bridges 286
VIII.1.2 Types of loads acting on bridges 287
VIII.1.3 Substructures supporting deck structures 288
VIII.1.4 Bridges – case studies 288
VIII.2 Conventional building details 331
VIII.2.1 General introduction 331
VIII.2.2 Case studies based on British practice 331
VIII.2.3 Case studies based on EC2 and European practices 368
VIII.2.4 Case studies based on American practices 376
VIII.3 Stadia, arenas and grandstands 378
VIII.3.1 Introduction 378
VIII.3.2 Glossary 378
VIII.3.3 Introduction to loads 381
VIII.3.4 Statistical data on loads on constructed facilities 383
VIII.3.5 Case study 1 385
VIII.3.6 Case study 2 389
VIII.3.7 Case study 3 395
VIII.4 Water-retaining structures and silos 397
VIII.4.1 Water-retaining structures 397
VIII.4.2 Silos 404
VIII.5 Bomb protective structures 408
VIII.5.1 General introduction 408
VIII.5.2 Data on bomb explosion on structures 408
VIII.5.3 Generalized data for a domestic nuclear shelter 413
VIII.6 Nuclear, oil and gas containments 417
VIII.6.1 Nuclear power and containment vessels 417
VIII.6.2 Oil containment structures 424
VIII.7 Concrete shells, chimneys and towers 432
VIII.7.1 General information 432
VIII.7.2 Shells 435
VIII.7.3 Case study 452

v
STRUCTURAL DETAILING IN CONCRETE

Preface

Preface to the first A number of books on various aspects of concrete design and detailing have
edition, 1992 been published but this is believed to be the first comprehensive detailing
manual. The aim of this book is to cover a wide range of topics, so simplifying
and reducing the work required to prepare structural drawings and details in
reinforced, prestressed, precast and composite concrete.
The book initially provides a list of extracts from relevant codes and current
practices. Where drawings are carried out using imperial units, a conversion
table is provided to change them into SI units.
The book is divided into eight sections: Section I deals with the general
requirements for structural detailing in concrete, basic drafting criteria and the
properties of materials. Section II is devoted entirely to the structural detailing
of beams and slabs. Section III covers reinforced concrete detailing of stairs
and staircases. A comprehensive description is given of the detailing of
reinforced concrete columns, frames and walls in Section IV. The reader is
also referred for more information to the later section on integrated
structures.
Section V covers prestressed concrete systems with some basic structural
detailing of beams and anchorages. Again the reader is referred to other
sections, in particular Section VIII regarding the use of prestressed tendon
elements in integrated structures. Section VI presents structural detailing in
composite construction, precast concrete elements, joints and connections.
Section VII includes basic structural detailing of reinforced concrete
foundations and earth-retaining structures. An effort is made to include a
number of foundation drawings so that the reader can appreciate the quality
and design required for a specific job.
Students of civil and structural engineering who have worked through to
this part of the book will have acquired the background necessary to draw the
majority of reinforced, prestressed, precast and composite concrete structures
commonly encountered in professional practice. To assist the reader in his/her
completion of drawings, an unusually large number of drawings have been
incorporated into the text since they are generally the principal communication
between the structural engineer/designer, architect, builder and client.
Case studies in Section VIII include the structural detailing of the following
special structures in concrete:

• reinforced concrete beam/slab bridge deck


• culvert bridge super and substructures
• continuous reinforced concrete girder deck
• reinforced concrete box bridge deck
• open spandrel arch bridge — reinforced and prestressed
• reinforced concrete rigid frame bridge details
• composite/steel — concrete bridge deck
• reinforced concrete rigid frame bridge
• bridge bearings and substructural layouts
• samples of reinforced concrete cylindrical shells, hyperbolic shells:

vi
PREAMBLE

° groin type hyperbolic paraboloid shells and domes, water retaining


structures and silos with elevated towers, nuclear shelter
° pressure and containment vessels for nuclear power plants, gas and oil
installations and cells for offshore platforms
° hydroelectric and irrigation/hydraulics structures, spillways, piers,
intakes, switch yard foundations, electric manholes, chutes, gates,
tunnels and culverts.

An increasing emphasis has been placed on the role of the designer in


planning reinforcement and structural details so that the detailer can do his/her
work thoroughly without having to complete the design himself/herself.
Improved methods and standards presented in the text should result in better
construction and reduced costs.
The book will serve as a useful text for teachers preparing a syllabus for
technician and graduate courses. Each major section has been fully explained
to permit the book to be used by practising engineers and postgraduate
students, particularly those facing the formidable task of having to design/
detail complicated structures for specific contracts and research assignments.
Contractors will also find this book useful in the preparation of construction
drawings.

M. Y. H. Bangash

Preface to the second This concrete detailing manual has been prepared to provide practical and up-
edition to-date information on many aspects of concrete construction, and is intended
for educators, designers, draftsmen and detailers, and all others who have an
interest in structural concrete work.
The text covers the full scope of structural detailing in the UK, Europe and
the USA, starting with the fundamentals of drawing, continuing with drafting
practice and conventional methods of detailing components, and concluding
with a number of case studies.
The first edition of the text was based on the British Standard codes and
practices. However, in the past decade or so there has been an increase in
international multipurpose concrete construction, and engineers on both sides
of the Atlantic (and elsewhere in the World) showed a desire for European and
American codes and practices to be included in this book. This task, taken
upon himself by the author, proved gigantic, especially the incorporation of
the newly developed Eurocode 2. Several organizations dealing in British,
European and American codes were approached and their advice was sought
in the preparation of this second edition.
Those who have used the first edition will find the main headings of the
various sections unchanged. The introduction to each section is as given in the
first edition. However, each section has typical explanatory notes and drawings
with up-to-date information on developmental methods. In some sections only
minimal alteration was required, while in others a complete revision was
needed. Each section was expanded with codified methods for drafting and
detailing concrete structures based on European and American practices. The
second edition of this text, therefore, covers the full scope of structural
detailing in the UK, Europe and the USA.
Section I now encompasses all general requirements for concrete structures
based on the three practices. Section II, on reinforced concrete beams and
slabs, now includes deep beams. Geometric staircases are now included in
Section III. Based on the three practices, columns, frames and walls are dis-
cussed in Section IV. Details on prestressed concrete are given in Section V,

vii
STRUCTURAL DETAILING IN CONCRETE

in which special provision is made for Eurocode 2. Section VI is mostly


unchanged.
Section VII, concerning concrete foundations and earth-retaining struc-
tures, has been modified in the light of current provisions indicated in
Eurocode 2 and the ACI/ASCE codes. Pile foundations are examined in detail,
and new sections on machine foundations, caissons, rafts and retaining walls
have been included. In Section VIII, which presents a series of case studies, a
great deal of modification is introduced. The bridge section, VIII.1, has been
extended to cover the three practices. VIII. 2 is a new section covering at
greater length conventional concrete building details. Similarly, a new section
under VIII.3 deals with structural details of stadia, arenas and grandstands.
Section VIII.4, on water-retaining structures and silos, has minor alterations.
Section VIII.5, on bomb protective structures, also contains new material,
while Section VIII.6 is mostly unchanged. Section VIII.7 covers concrete
shells, chimneys and towers and includes a new section on tower design/
detailing. Section VIII.7 of the first edition, on hydroelectric and irrigation
structures, was excluded from this edition for market reasons.
This book should serve both as a primer for trainee detailers and as a
reference manual for more experienced personnel. Engineers, architects and
contractors working in countries on different continents will find the
comparative study in the book useful both for reference and for practical use
when preparing drawings to different codes for specific countries.

M. Y. H. Bangash

viii
PREAMBLE

Acknowledgements

Acknowledgements The author wishes to express his appreciation to friends, colleagues and some
for the first edition students who have assisted in the early developments of this book by
suggesting relevant changes. The author has received a great deal of
assistance, encouragement and inspiration from practising engineers and
contractors, particularly those for whom he has acted as consultant. The author
is indebted to all those people and organizations who are referred to in this
book and to the following, in particular, for making this book a reality:
Indian Concrete Journal, Delhi, India
The Indian Road Congress, Delhi, India
The Public Works Departments, Delhi and Mahrashtra, India
The Governments of Ivory Coast and Ghana
The Institution of Civil Engineering Library, London, UK
Kaiser Engineers and Contractors, California, USA
Bechtel Engineering, California, USA
Chatterjee, Polkes, Consulting Architects, Delhi, India
Dr F. Garas, Taylor Woodrow Construction Ltd, Southall, UK
United States Bureau of Reclamation, Washington DC, USA
Pakistan Engineering Congress, Lahore, Pakistan
West Pakistan Water and Power Development Authority (WAPDA), Pakistan
Punjab Public Works (PWD) Department, Lahore, Pakistan
Gammons (India) Ltd, Delhi, Bombay, India
Mott McDonald, Croydon, Surrey, UK
Birkenhead Project on Silo, Australia
The Atomic Power Construction Ltd, Sutton, UK
The former Central Electricity Generating Board, UK
TVA Tennessee Valley Authority, Tennessee, USA
The United States Nuclear Regulatory Commission, USA
The International Association of Shell Structures, Spain
British Standards, London, UK
American Concrete Institute, Detroit, USA
The Offshore Technology Conference Center, Houston, Texas, USA
The UK Atomic Energy, Winfrith, Dorset, UK
A number of original drawings have been modified to comply with the current
drafting codes and requirements.
The undertaking could never have been achieved without the patience,
encouragement and understanding of the author’s family.
Artwork Acknowledgements
III.6,7,8,9 Birchwood Concrete Products
V.4 PSC Equipment Ltd
V.5,6,7,8,9,10,11 BBRV, Simon Carves
V.13,14 Cabco
VIII.1.19 Overseas Projects Corporation of Victoria, Australia
VIII.2.3.a,2.16 S. Eggwertz, Consulting Engineer
VIII.2.6,7,8 Perkins and Will, Chicago
VIII.2.10 S.D. Castillo
VIII.6.3,4,5 Kaiser Engineers and Constructors Inc.

ix
STRUCTURAL DETAILING IN CONCRETE

Acknowledgements The author is indebted to the following organizations and individuals, who
for the second edition contributed enormous amounts of time and material for the preparation of the
Second Edition:

Hyder Consulting Engineers, Guildford, Surry, UK


Rendel Palmer and Tritton, London, UK
WSP International Limited, Reading, UK
Gifford and Partners, Southampton, UK
Price and Myers, Consulting Engineers, London, UK
ASZ Partners, Consulting Engineers, Ilford, Essex, UK
Birzulis Associates Pty, Rozelle, Australia
Ward & Cole, London, UK
AGRA Inc., Ontario, Canada
The Louis Berger Group, New Jersey, USA
Black & Veatch, Kansas City, USA
Sturm Consulting Engineers, Oklahoma, USA
Dames and More Group, Los Angeles, California, USA
Tams Consultant Inc., New York, USA
Weidlinger Associates, New York, USA
Florida Department of Transportation, Florida, USA
Hayza Engineering Co., Chicago, Illinois, USA
American Concrete Institute, USA
Finley McNary Engineers, Tallahassee, Florida, USA
Mitchell/Giurgola, Architects, New York, USA
Cesar Pelli & Associates, Architects, Houston, Texas, USA
CBM Engineers Inc., Houston, Texas
ASTM, USA
HGHB/Douglas Barker, Architects, San Francisco, California, USA
Anshen + Allen, Architects, Los Angeles, California, USA
Austro-Consult, Vienna, Austria
Balslev A/S, Consulting Engineers, Denmark
Carl.Bro Group, Glostrup, Denmark
AHT Group GmbH, Essen, Germany
STUDIO Hamburg, Hamburg, Germany
ARCH-ING-SERVICE, Sudtirol, Italy
ABT Consulting Engineers, Arnhem, Netherlands
BKH Consulting Engineers, Delft, Netherlands
Euro-consult, Arnhem, Netherlands
Hoskoning BV, Consulting Engineers and Architects, Nijmegen, Netherlands
Dywidag System International, Monaco
Wayss and Freitag, Frankfurt, Germany
Leonhardt, Andrä and Partners GmbH, Stuttgart, Germany
Rolf Johann, Volkert + Zimmermann, Structural Engineers, Zurich,
Switzerland
Ballast Needam NV, Amsterdam, Netherlands
Societa Transporti Pubblici Sondrio (STPS), Italy
Sigma C Soft, Padona, Italy
Studio Software, Rome, Italy
Mediant Software, Milan, Italy
Andres Perea Ortega, Architects, Madrid, Spain
Giovanni, Onni, Architects, Rome, Italy
Jean Louis Godivier, Architects, Paris, France
Philipp Holzmann A/G, Essen, Germany
I’industria Italiana del Cemento, Rome, Italy
Döring & Partners, Architects, Dusseldorf, Germany

x
PREAMBLE

Blondeau Ingenierie, France


Bernard Quirot, Artchitects, Paris, France
SARI Development, Structural Engineers and Contractors, Paris, France
Monique Labbe, Architects, Ivry-sur-Seine, France
Guido Furlanetto, Engineering Design Office, Italstrade SPA, Milan, Italy
Ernst & Sohn Verlag GmbH, Berlin, Germany
The author is grateful for the enormous support given by the following
individuals, without whom this work could not have been achieved:
Mike Chrimes, Librarian, and his staff, Institution of Civil Engineers, London,
UK
Sue Claxton, Librarian, Institution of Structural Engineers, London, UK
Prof Dr-Ing J. Eibl, Karlsruhe, Germany
Prof Dr-Ing U. Quast, University of Hamburg, Germany
Prof Dr-Ing E Wölfel, Berlin, Germany
Prof Dr A.R. Cusens, University of Leeds, UK
Mr Khalid Chaudhry, Director, Ward & Cole, London, UK
The manuscript was typed by Miss Chloe Mantzari and Mr A.M. dos Santos
under a special contract and my thanks to the two young students.

xi
STRUCTURAL DETAILING IN CONCRETE

Metric conversions

Overall geometry

Spans 1 ft  0·3048 m
Displacements 1 in.  25·4 mm
Surface area 1 ft2  0·0929 m2
Volume 1 ft3  0·0283 m3
1 yd3  0·765 m3

Structural properties

Cross-sectional dimensions 1 in.  25·4 mm


Area 1 in.2  645·2 mm2
Section modulus 1 in.3  16·39  103 mm3
Moment of inertia 1 in.4  0·4162  106 mm4

Material properties

Density 1 lb/ft3  16·03 kg/m3


Modulus of elasticity and stress 1 lb/in.2  0·006895 MPa
1 kip/in.2  6·895 MPa

Loadings

Concentrated loads 1 lb  4·448 N


1 kip  1000 lbf  4·448 kN
Density 1 lb/ft3  0·1571 kN/m3
Linear loads 1 kip/ft  14·59 kN/m
Surface loads 1 lb/ft2  0·0479 kN/m2
1 kip/ft2  47·9 kN/m2

Prefixes in SI units
G  giga 109
M  Mega 106
k  kilo 103
m  milli 10  3
Pa  Pascal

xii

You might also like