LARGE DIAMETER TOOL JOINTS

DIMENSION AND STRENGTH DATA

API AND NON-API
BOX PIN TENSILE YIELD TORSION YIELD RECOMMENDED
SIZE CONNECTION O.D. I.D. STRENGTH STRENGTH Make -Up Torque
TYPE (in.) (in.) (Lbs) (Ft-Lbs.) (Ft-Lbs.)

2.3/8
WT 23 3 1/8 1 1/2 386,000 10,400 2200 - 8300

2.7/8 GHT PAC 3 1/8 1 1/2 214,300 8,600 5,100

3.1/2

4" HT 40 5" 2.563 513,600 41,900 11,600-18,600

4.1/2

5.1/2

6.5/8
 LARGE DIAMETER TOOL JOINTS
DIMENSION AND STRENGTH DATA
API AND NON-API
BOX PIN TENSILE YIELD TORSION YIELD RECOMMENDED
SIZE CONNECTION O.D. I.D. STRENGTH STRENGTH Make -Up Torque
TYPE (in.) (in.) (Lbs) (Ft-Lbs.) (Ft-Lbs.)
API REG 3.1/8 1 375,500 7,500 3,700
2.3/8 API I.F. 3.3/8 1.3/4 313,680 6,800 3,400
API REG 3.3/4 1.1/4 493,600 13,000 6,500
API I.F. 4.1/8 2.1/8 447,130 11,800 5,900
2.7/8 S.H. 3.3/8 1.3/4 313,680 6,800 3,400
X-HOLE 4.1/4 1.7/8 505,080 13,400 6,700
API REG 4.1/4 1.1/2 727,400 15,100 7,500
API F.H. 4.5/8 2.1/8 779,900 16,300 8,100
API I.F. 4.3/4 2.11/16 587,310 18,100 9,100
3.1/2 D.S.L. 3.7/8 1.13/16 561,120 14,000 7,000
S.H. 4.1/8 2.1/8 447,130 11,800 6,000
X-HOLE 4.3/4 2.7/16 570,940 17,100 8,550
H-90 5 2.3/4 663,130 23,500 11,800
H-90 5.1/4 2.3/4 663,130 23,800 11,800
API F.H. 5.1/4 2.13/16 757,500 23,500 11,800
4 API I.F. 6 3.1/4 901,170 33,600 16,900
S.H. 4.5/8 2.9/16 512,040 15,000 7,500
H-90 5.1/2 2.13/16 913,470 35,400 17,700
API REG 5.1/2 2.1/4 1,262,000 30,000 15,000
API F.H. 5.3/4 3 1,017,000 35,400 17,700
API I.F. 6.3/8 3.3/4 944,000 37,800 18,900
4.1/2 X-HOLE 6.1/4 3.1/4 901,150 34,000 17,000
H-90 6 3.1/4 938,150 38,900 19,500
H-90 6 3 1,085,410 45,200 22,600
5 X-HOLE 6.3/8 3.3/4 939,100 37,700 18,900
API REG 6.3/4 2.3/4 1,779,000 61,000 30,000
5.1/2 API F.H. 7 4 1,265,760 56,300 28,000
API I.F. 7.3/8 4.13/16 1,265,500 77,600 38,800
API REG 7.3/4 3.1/2 1,867,000 86,000 43,000
6.5/8 API I.F. 8 5 1,448,800 74,200 37,100
 Drill pipe Drill pipe
lbs/ft tool jts tool jts tool jts tool jts
Nom size nom wt connection new od new id make up tq Nom size nom wt connection new od new id make up tq
EU 75 4.85 WO 3 3/8 2 2267 15.7 NC40 4FH 5 1/4 2 11/16 10179
EU 75 4.85 NC26 IF 3 3/8 1 3/4 3239 15.7 NC46 4IF 6 3 1/4 9937
EU 75 4.85 OH 3 1/8 2 2263 15.7 H90 5 1/2 2 13/16 9673
EU 75 4.85 SLH90 3 1/4 2 2564 15.7 NC40 4FH 5 1/2 2 7/16 12569
2 3/8 6.65 PAC 2 7/8 1 3/8 2455 4 15.7 NC46 4IF 6 3 12813
EU 75 6.65 NC26 IF 3 3/8 1 3/4 3239 15.7 H90 5 1/2 2 13/16 12497
EU 75 6.65 SLH90 3 1/4 2 2560 15.7 NC46 4IF 6 3 13547
EU 75 6.65 OH 3 1/4 1 3/4 3149 15.7 H90 5 1/2 2 13/16 17700
EU 94 6.65 NC26 IF 3 3/8 1 3/4 3005 15.7 NC46 4IF 6 2 5/8 18083
EU 105 6.65 NC26 IF 3 3/8 1 3/4 3279 EU 135 15.7 NC46 4IF 6 2 7/8 18083
6.85 NC31(2 7/8IF) 4 1/8 2 1/8 5935 IEU 75 16.6 FH 6 3 12125
6.85 WO 4 1/8 2 7/16 3756 IEU 75 16.6 NC46 XH 6 1/4 3 1/4 12085
6.85 OH 3 3/4 2 7/16 3242 IEU 75 16.6 OH 5 7/8 3 3/4 11861
6.85 SLH90 3 7/8 2 7/16 3815 IEU 75 16.6 NC50 IF 6 3/8 3 3/4 11591
10.4 NC31(2 7/8IF) 4 1/8 2 1/8 5935 IEU 75 16.6 H90 6 3 1/4 12215
10.4 XH 4 1/8 1 7/8 6798 IEU 95 16.6 FH 6 2 3/4 14945
10.4 NC26 (2 7/8SH) 3 3/8 1 3/4 4415 IEU 95 16.6 NC46 XH 6 1/4 3 15035
10.4 OH 3 7/8 2 5/32 4542 IEU 95 16.6 NC50 IF 6 3/8 3 3/4 14927
10.4 SLH90 3 7/8 2 5/32 4531 IEU 95 16.6 H90 6 3 15115
2 7/8 10.4 PAC 3 1/8 1 1/2 3439 4 1/2 16.6 FH 6 2 3/4 16391
10.4 NC31 2 7/8 IF 4 1/8 2 5726 IEU 105 16.6 NC46 XH 6 1/4 3 16546
10.4 SLH90 3 7/8 2 5/32 5704 IEU 105 16.6 NC50 IF 6 3/8 3 3/4 16634
10.4 NC31 2 7/8 IF 4 1/8 2 6110 IEU 105 16.6 H90 6 3 16264
10.4 NC31 2 7/8 IF 4 3/8 1 5/8 7694 IEU 135 16.6 NC46 XH 6 1/4 2 3/4 21230
9.5 NC38 WO 4 3/4 3 5773 IEU 135 16.6 NC50 IF 6 3/8 3 1/2 21018
9.5 NC38 IF 4 3/4 2 11/16 5803 IEU 75 20.00 FH 6 3 14231
9.5 OH 4 3/4 3 5934 IEU 75 20.00 NC46 XH 6 1/4 3 14288
9.5 SLH90 4 5/8 3 6323 IEU 75 20.00 NC50 IF 6 3/8 3 5/8 14082
13.3 NC38 IF 4 3/4 2 11/16 9054 IEU 75 20.00 H90 6 3 13815
13.3 NC31 SH 4 1/8 2 1/8 6893 IEU 95 20.00 FH 6 2 1/2 17861
13.3 OH 4 3/4 2 11/16 8653 IEU 95 20.00 NC46 XH 6 1/4 2 3/4 18083
13.3 H90 5 1/4 2 3/4 11924 IEU 95 20.00 NC50 IF 6 3/8 3 1/2 17497
13.3 NC38 IF 5 2 9/16 8822 IEU 95 20.00 H90 6 3 17929
13.3 SLH90 4 5/8 2 11/16 8742 IEU 105 20.00 NC46 XH 6 1/4 2 1/2 19644
13.3 H90 5 1/4 2 3/4 8839 IEU 105 20.00 NC50 IF 6 3/8 3 1/2 20127
3 1/2 13.3 NC38 IF 5 2 7/16 9879 IEU 135 20.00 NC50 IF 6 5/8 2 7/8 25569
13.3 NC40 4FH 5 3/8 2 7/16 12569 22.82 NC50 IF 6 3/8 3 5/8 20618
13.3 NC38 3 1/2IF 5 2 1/8 12614 22.82 NC46 XH 6 1/4 3 19830
15.5 NC38 IF 5 2 9/16 7785 IEU 75 19.5 NC50 XH 6 3/8 3 3/4 18800
15.5 NC38 IF 5 2 7/16 9879 IEU 95 19.5 NC50 XH 6 3/8 3 1/2 19919
15.5 NC38 IF 5 2 1/8 10957 IEU 95 19.5 H90 6 1/2 3 1/4 19862
15.5 NC40 4FH 5 1/4 2 9/16 11363 IEU 105 19.5 NC50 XH 6 1/2 3 1/4 21914
15.5 NC40 4FH 5 1/2 2 1/4 14419 IEU 105 19.5 H90 6 1/2 3 21727
11.85 NC46 IF 6 3 1/4 7843 IEU 135 19.5 NC50 XH 6 5/8 2 3/4 28381
11.85 NC46 WO 5 3/4 3 7/16 7843 IEU 136 19.5 5 1/2 FH 7 1/4 3 1/2 28737
11.85 OH 5 1/4 3 15/32 8653 5 25.5 NC50 XH 6 3/8 3 1/2 20127
11.85 H90 5 1/2 2 13/16 17721 IEU 75 25.6 5 1/2 FH 7 3 1/2 20205
14.00 NC40 4FH 5 1/4 2 13/16 9017 IEU 95 25.6 NC50 XH 6 1/2 3 25569
14.00 NC46 4IF 6 3 1/4 7832 IEU 95 25.6 5 1/2 FH 7 3 1/2 25450
14.00 SH 4 5/8 2 9/16 8782 IEU 105 25.6 NC50 XH 6 5/8 2 3/4 27438
4 14.00 OH 5 1/2 3 1/4 9131 IEU 105 25.6 5 1/2 FH 7 1/4 3 1/2 27644
14.00 H90 5 1/2 2 13/16 17721 IEU 135 25.6 5 1/2 FH 7 1/4 3 1/4 35446
14.00 NC40 4FH 5 1/4 2 11/16 16813 IEU 75 21.9 FH 7 4 19172
14.00 NC46 4IF 6 3 1/4 16813 IEU 95 21.9 FH 7 3 3/4 25483
14.00 H90 5 1/2 2 13/16 17721 IEU 95 21.9 H90 7 3 1/2 25478
14.00 NC40 4FH 5 1/2 2 7/16 12569 IEU 105 21.9 FH 7 1/4 3 1/2 27645
14.00 NC46 4IF 6 3 1/4 12813 IEU 135 21.9 FH 7 1/2 3 35446
EU 105 14.00 H90 5 1/2 2 13/16 17721 IEU 75 24.7 FH 7 4 22294
EU 135 14.00 NC46 4IF 6 3 15787 IEU 95 24.7 FH 7 1/4 3 1/2 27645
5.5 105 24.7 FH 7 1/4 3 1/2 29836
IEU 135 24.7 FH 7 1/2 3 38901
6 5/8 25.5 FH 8 5 37100
 LARGE DIAMETER TOOL JOINTS
DIMENSION AND STRENGTH DATA
API AND NON-API
BOX PIN TENSILE YIELD TORSION YIELD RECOMMENDED
SIZE CONNECTION O.D. I.D. STRENGTH STRENGTH Make -Up Torque
TYPE (in.) (in.) (Lbs) (Ft-Lbs.) (Ft-Lbs.)
API REG 3.1/8 1 375,500 7,500 3,700
2.3/8 API I.F. 3.3/8 1.3/4 313,680 6,800 3,400
API REG 3.3/4 1.1/4 493,600 13,000 6,500
API I.F. 4.1/8 2.1/8 447,130 11,800 5,900
2.7/8 S.H. 3.3/8 1.3/4 313,680 6,800 3,400
X-HOLE 4.1/4 1.7/8 505,080 13,400 6,700
API REG 4.1/4 1.1/2 727,400 15,100 7,500
API F.H. 4.5/8 2.1/8 779,900 16,300 8,100
API I.F. 4.3/4 2.11/16 587,310 18,100 9,100
3.1/2 D.S.L. 3.7/8 1.13/16 561,120 14,000 7,000
S.H. 4.1/8 2.1/8 447,130 11,800 6,000
X-HOLE 4.3/4 2.7/16 570,940 17,100 8,550
H-90 5 2.3/4 663,130 23,500 11,800
H-90 5.1/4 2.3/4 663,130 23,800 11,800
API F.H. 5.1/4 2.13/16 757,500 23,500 11,800
4 API I.F. 6 3.1/4 901,170 33,600 16,900
S.H. 4.5/8 2.9/16 512,040 15,000 7,500
H-90 5.1/2 2.13/16 913,470 35,400 17,700
API REG 5.1/2 2.1/4 1,262,000 30,000 15,000
API F.H. 5.3/4 3 1,017,000 35,400 17,700
API I.F. 6.3/8 3.3/4 944,000 37,800 18,900
4.1/2 X-HOLE 6.1/4 3.1/4 901,150 34,000 17,000
H-90 6 3.1/4 938,150 38,900 19,500
H-90 6 3 1,085,410 45,200 22,600
5 X-HOLE 6.3/8 3.3/4 939,100 37,700 18,900
API REG 6.3/4 2.3/4 1,779,000 61,000 30,000
5.1/2 API F.H. 7 4 1,265,760 56,300 28,000
API I.F. 7.3/8 4.13/16 1,265,500 77,600 38,800
API REG 7.3/4 3.1/2 1,867,000 86,000 43,000
6.5/8 API I.F. 8 5 1,448,800 74,200 37,100
 DRILL COLLAR WEIGHT (POUNDS PER FOOT)
COLLAR DRILL COLLAR I.D, ( inches )
O.D.(in.) 1 1.1/4 1.1/2 1.3/4 2 2.1/4 2.1/2 2.13/16 3 3.1/4 3.1/2 3.3/4 4
2.7/8 19 18 16
3 21 20 18
3.1/8 22 22 20
3.1/4 26 24 22
3.1/2 30 29 27
3.3/4 35 33 32
4 40 39 37 35 32 29
4.1/8 43 41 39 37 35 32
4.1/4 46 44 42 40 38 35
4.1/2 51 50 48 46 43 41
4.3/4 54 52 50 47 44
5 61 59 56 53 50
5.1/4 68 65 63 60 57
5.1/2 75 73 70 67 64 60
5.3/4 82 80 78 75 72 67 64 60
6 90 88 85 83 79 75 72 68
6.1/4 98 96 94 91 88 83 80 76 72
6.1/2 107 105 102 99 96 91 89 85 80
6.3/4 116 114 111 108 105 100 98 93 89
7 125 123 120 117 114 110 107 103 98 93 84
7.1/4 134 132 130 127 124 119 116 112 108 103 93
7.1/2 144 142 139 137 133 129 126 122 117 113 102
7.3/4 154 152 150 147 144 139 136 132 128 123 112
8 165 163 160 157 154 150 147 143 138 133 122
8.1/4 176 174 171 168 165 160 158 154 149 144 133
8.1/2 187 185 182 179 176 172 169 165 160 155 150
9 210 208 206 203 200 195 192 188 184 179 174
9.1/2 234 232 230 227 224 220 216 212 209 206 198
9.3/4 248 245 243 240 237 232 229 225 221 216 211
10 261 259 257 254 251 246 243 239 235 230 225
11 317 315 313 310 307 302 299 295 291 286 281
12 379 377 374 371 368 364 361 357 352 347 342
 HEVI- WATE DRILLPIPE

STANDARD
PIPE CONNECTION Tool Joint Tool Joint Tube Nom.Wt. TORQUE
SIZE TYPE O.D. I.D. I.D. Lbs/ft. FT/Lbs.
3.1/2 3.1/2 IF 4.3/4 2.3/16 2" 25.3 9,900
4 4 FH 5.1/4 2.11/16 2.563 29.7 13,250
4.1/2 4 IF 6.1/4 2.7/8 2.3/4 39.9 21,800
5 4,1/2 IF 6.1/2 3.1/8 3" 48.5 29,400
6.5/8 6.5/8 FH 8" 5" 5" 57 46,700
6.5/8 6.5/8 FH 8" 4" 4" 81.1 46,700
SPIRAL-WATE
3.1/2 3.1/2 IF 4.3/4 2.3/16 2.1/8 28.3 9,900
4 4 FH 5.1/4 2.11/16 2.563 33.8 13,250
4.1/2 4 IF 6.1/4 2.7/8 2.3/4 44 21,800
5 4.1/2 IF 6.1/2 3.1/8 3" 55.3 29,400
5.1/2 5.1/2 FH 7" 3.1/2 3.1/4 63 32,500
6.5/8 6.5/8 FH 8" 5" 5" 57 46,700
 HWDP

HEVI WATE DRILL PIPE

NOM TOOL JOINT TUBE NOM TOOL JIONT max

SIZE OD ID ID LBM/FT CONNECTION TORQUE min
STANDARD
3 1/2 4 3/4 2 3/16 2 1/9 25.300 3 1/2 IF NC38 9900
4 5 1/4 2 11/16 2.563 29.700 4 FH NC40 13250
4 1/2 6 1/4 2 7/8 2.750 39.900 4 IF NC46 21800
5 6 1/2 3 1/8 3.000 48.500 4 1/2 IF NC50 29400
6 5/8 8 5 5.000 57.000 6 5/8 FH 46700
6 5/8 8 4 4.000 81.100 6 5/8 FH 46700 37,000

SPIRAL-WATE
3 1/2 4 3/4 2 3/16 2.125 28.300 3 1/2 IF NC38 9900
4 5 1/4 2 11/16 2.563 33.800 4 FH NC40 13250
4 1/2 6 1/4 2 7/8 2.750 44.000 4 IF NC46 21800
5 6 1/2 3 1/8 3.000 55.300 4 1/2 IF NC50 29400
5 1/2 7 3 1/2 3.250 63.000 5 1/2 FH 32500
6 5/8 8 5 5.000 57.000 6 5/8 FH 46700

Page 7
BAKER PIPE INFO AND CONVERTIONS
DP Nom. Wt. Capacity ID
Lbs Kg/m inch
2-7/8" Pac 10.4 15.47 2.345 2.151
3-1/2" IF 15.5 23.06 3.431 2.6
5" IF 19.5 29.02 9.266 4.276
5-1/2" FH 21.9 32.6 11.35 4.778
6-5/8" FH 25.2 37.5 17.8 5.965
6-5/8" FH 29.7 44.26 17.19 5.822
5" HW 50 74.4 4.56 3
5-1/2" HW 54.4 81 5.35 3.25
6-5/8" HW 58 86.3 11.44 4.75
6-5/8" HW 79 117.55 8.11 4

DC Nom. Wt. Capacity ID

Lbs Kg/m inch
4-3/4" 46.8 69.6 2.565 2.25
6-1/2" 91.8 136.6 4.011 2.812
7-3/4" 136.5 203.1 4.56 3
8" 143 212.8 5.35 3.25
8" 147 218.8 4.56 3
9" 192.5 286.4 4.56 3
9-1/2" 217.2 323.2 4.56 3

CSG. Nom. Wt. Capacity ID

Lbs Kg/m inch
5" 15 22.32 9.85 4.408
5" 18 26.78 9.26 4.276
7" 26 38.69 19.96 6.276
7" 29 43.15 19.38 6.184
9-5/8" 47 69.94 38.19 8.681
9-5/8" 53.5 79.61 36.92 8.535
10-3/4" 45.5 67.7 50.17 9.95
10-3/4" 60.7 90.3 47.29 9.66
13-3/8" 68 99.61 78.08 12.413
13-3/8" 72 106.3 77.24 12.346

LBS/ft > KG/M = LBS/ft x 1,488

LBS > KG = LBS / 2,205
M > ft =M x 3,281
INCH > CM = INCH x 2,540
Nm > ft/LBS= Nm / 1,35582
BOYENCY(US) = (65,5-MW) /65,5
BOYENCY(SG) = (7,85-MW) / 7,85

TORQUE LIMIT ON 4-1/2" IF = 25 Kft/LBS = 34 KNm

5-1/2" IF M. & 7" HR TOOL = 32 Kft/LBS = 43 KNm
TENSION ON 5" PUP = 300 TON, 5-1/2" =
TENSION ON 5" HR TOOL = 156 TON = 344 KLBS
TENSION ON 7" HR TOOL = 270 TON = 597 KLBS
TENSION ON 9-5/8" HR = 362 TON = 800 KLBS
 Tool Joints 3-1/8" - 6-5/8" (Dimension & Strength Data)
Recommended Recommended
Tensile Yield Torsion Yield
Make-up Make-up
Size ConnectionType O.D.(inches) I.D.(inches) Strength Strength
Torque Torque
(pounds) (foot-pounds)
(foot-pounds) ( kNm )

3" CDP 2.692 3.650

3.1/8" PRT 3.1/8 1 323.000 12.285 6.140 8.325
3.1/2" AM.PAC 3.3/4 2 352.800 8.800 4.400 5.966
3.1/2" ECHT* 3.1/2 1.1/2 350.700 14.970 7.353 9.969
3.1/2" API.REG 4.1/4 1.1/2 727.400 15.100 7.500 10.169
3.1/2" API.FH 4.5/8 2.1/8 779.900 16.300 8.100 10.982
3.1/2" API.IF (= NC38) 4.3/4 2.11/16 587.310 18.100 9.100 12.338
3.1/2" Hughes DSL 3.7/8 1.13/16 561.120 14.000 7.000 9.491
3.1/2" Hughes SH(=NC31) 4.1/8 2.1/8 447.130 11.800 6.000 8.135
3.1/2" Hughes XH 4.3/4 2.7/16 570.940 17.100 8.550 11.592
3.1/2" Hughes H-90 5 2.3/4 663.130 23.500 11.800 15.999
3.1/2" Hughes H-90 5.1/4 2.3/4 663.130 23.800 11.800 15.999
3.1/2" PH-4 (C,L,N)** 4.1/2 2.406 - - 8.438 11.440
4.563 2.3/8 - - 9.000 12.202
3.1/2" PH-4 (P)** 4.1/2 2.406 - - 10.688 14.491
4.563 2.3/8 - - 11.250 15.253
3.1/2" PH-6 (C,L,N)** 4.313 2.11/16 - - 6.188 8.390
4.1/2 2.485 - - 6.188 8.390
3.1/2" PH-6 (P)** 4.313 2.11/16 - - 7.875 10.677
4.1/2 2.485 - - 7.875 10.677
4" API.FH 5.1/4 2.13/16 757.500 23.500 11.800 15.999
4" API.IF (= NC46) 6 3.1/4 901.170 33.600 16.900 22.913
4" Hughes S.H. 4.5/8 2.9/16 512.040 15.000 7.500 10.169
4" Hughes H-90 5.1/2 2.13/16 913.470 35.400 17.700 23.998
4" PH-4 (C,L,N)** 5 2.92 - - 9.562 12.964
5.188 2.7 - - 10.688 14.491
4" PH-4 (P)** 5 2.92 - - 11.812 16.015
5.188 2.7 - - 12.938 17.542
4" PH-6 (C,L,N)** 4.5/8 3.275 - - 6.188 8.390
4" PH-6 (P)** 4.5/8 3.275 - - 7.875 10.677
4.1/2" API.REG 5.1/2 2.1/4 1,262,000 30.000 15.000 20.337
4.1/2" API.FH 5.3/4 3 1,017,000 35.400 17.700 23.998
4.1/2" API.IF (= NC50) 6.3/8 3.3/4 944.000 37.800 18.900 25.625
4.1/2" Hughes XH 6-1/4 3.1/4 901.150 34.000 17.000 23.049
4.1/2" Hughes H-90 6 3.1/4 938.150 38.900 19.500 26.438
4.1/2" Hughes H-90 6 3 1,085,410 45.200 22.600 30.641
5.1/2 3.42 - - 10.688 14.491
4.1/2" PH-4 (C,L,N)** 5.563 3.3 - - 11.250 15.253
5.688 3.16 - - 12.938 17.542
5.1/2 3.42 - - 13.500 18.304
4.1/2" PH-4 (P)** 5.563 3.3 - - 14.625 19.829
5.688 3.16 - - 16.312 22.116
4.1/2" PH-6 (C,L,N)** 5.1/8 3.765 - - 6.750 9.152
5.313 3.56 - - 8.438 11.440
4.1/2" PH-6 (P)** 5.1/8 3.765 - - 8.438 11.440
5.313 3.56 - - 10.688 14.491
5" Hughes XH 6.3/8 3.3/4 939.100 37.700 18.900 25.625
5.1/2" API.REG 6.3/4 2.3/4 1,779,000 61.000 30.000 40.675
5.1/2" API.FH 7 4 1,265,760 56.300 28.000 37.963
5.1/2" API.IF 7.3/8 4.13/16 1,265,500 77.600 38.800 52.606
6.5/8" API.REG 7.3/4 3.1/2 1,867,000 86.000 43.000 58.300
6.5/8" API.FH 8 5 1,448,800 74.200 37.100 50.301
Strength based on a material yield of 120,000 psi
* Double shouldered internal connection
**Max. Yield Strength C-75: 90,000 psi; L-80: 95,000 psi; N-80: 110,000 psi; P-105: 135,000 psi

TOOLJT.XLS
 Rotary Shouldered Connection Interchangeability
NC 26 = 2.3/8" IF = 2.7/8" SH
NC 31 = 2.7/8" IF = 3.1/2" SH
NC35 = 3" IF
NC 38 = 3.1/2" IF = 4.1/2" SH
NC 40 = 4" FH = 4.1/2" DSL
NC 46 = 4" IF = 4.1/2" XH
NC 50 = 4.1/2" IF = 5" XH = 5.1/2" DSL

NC 23

TOOLJT.XLS
SMALL DIAMETER TOOL JOINTS
DIMENSION AND STRENGTH DATA*
TEN YIELD TOR/ Yeild REC
JOINT O.D. I.D. STRENGTH STRENGTH M/U To
(in.) (in.) (Lbs) (Ft-Lbs) (Ft-Lbs)
1 AM MT 1.562 0.75 68,100 765 500
1 AM MT 1.562 0.813 58,080 650 450
1 AM MT DSI 1.562 0.75 68,100 1,300 500
1-1/4 AM MT 1.75 1 69,698 865 500
1-1/4 AM MT 1.75 0.875 93,984 1,265 650
1-1/4 AM MT 1.75 0.8125 104,808 1,265 650
1-1/4 AM MT 1.75 0.75 115,000 1,265 650
1.1/4 F.J. (REG ) 2.188 0.63 155,300 2,150 1,075
1-1/4 AM MT DSI 1.75 0.875 93,984 1,800 650
1-1/2 AM MT 2 1 127,100 1,770 950
1-1/2 AM MT 2 0.156 92,136 1,285 700
1-1/2 AM MT 2 1.125 99,528 1,385 750
1-1/2 AM MT 2 1.063 113,784 1,585 900
1-1/2 AM MT 2 1 127,100 2,800 950
1.9/16 HOMCO S/H 1.9/16 0.937 71,120 900 450
1-5/8 BAASH ROSS 1.66 0.75 89,375 1,050 525
1.13/16HOMCO S/H 1.813 1 111,000 900 450
1.13/16 HOMCO FJ 1.813 0.75 113,000 1,600 800
1.13/16 PRT 1.813 0.75 110,000 1,595 800
1.13/16 WILSON FJ 1.813 0.75 113,000 1,600 800
2.1/6 AM MT DSI 2.33 1.25 135,036 3,500 1,100
2-1/4 PRT 2.25 0.75 181,900 4,600 2,300
2-1/4 TSS 2.25 1 142,500 2,100 500
2-3/8 AM PAC 2.875 1.375 238,440 4,800 2,400
2-3/8 AM PAC DSI** 2.375 1.5 201,900 6,490 3,250
2-3/8 API REG DSI** 3.125 1 375,500 8,045 4,020
2-3/8 HOMCO FJ 2.5 1 203,100 3,350 1,670
2.3/8 WILSON FJ 2.5 1.063 138,000 4,490 2,250
2-7/8 AM OH 3.875 2.151 345,360 8,900 4,450
2.7/8 AM OH L/W 3.75 2.441 223,680 5,700 2,850
2-7/8 AM PAC 3.125 1.5 269,470 5,800 2,900
2-7/8 AM PAC DSI** 3.125 1.5 269,470 7,290 3,650
3-1/8 PRT 3.125 1 323,000 12,285 6,140
3-1/2 AM PAC 3.75 2 352,800 8,800 4,400
4-1/4 PRT 4.25 2 507,600 26,500 13,250
 SMALL DIAMETER TOOL JOINTS
DIMENSION AND STRENGTH DATA*
TENSILE YIELD TORSION YIELD RECOMMENDED
JOINT O.D. I.D. STRENGTH STRENGTH Make-Up Torque
(in.) (in.) (Lbs) (Ft-Lbs) (Ft-Lbs)
1 AM MT 1.9/16 3/ 4 68,100 765 500
1 AM MT 1.9/16 13/16 58,080 650 450
1 AM MT DSI 1.9/16 3/ 4 68,100 1,300 500
1-1/4 AM MT 1.3/4 1 69,698 865 500
1-1/4 AM MT 1.3/4 7/ 8 93,984 1,265 650
1-1/4 AM MT 1.3/4 13/16 104,808 1,265 650
1-1/4 AM MT 1.3/4 3/ 4 115,000 1,265 650
1.1/4 F.J. (REG ) 2.3/16 5/ 8 155,300 2,150 1,075
1-1/4 AM MT DSI 1.3/4 7/ 8 93,984 1,800 650
1-1/2 AM MT 2 1 127,100 1,770 950
1-1/2 AM MT 2 1.5/32 92,136 1,285 700
1-1/2 AM MT 2 1.1/8 99,528 1,385 750
1-1/2 AM MT 2 1.1/16 113,784 1,585 900
1-1/2 AM MT 2 1 127,100 2,800 950
1.9/16 HOMCO SLIMHOLE 1.9/16 89/95 71,120 900 450
1-5/8 BAASH ROSS 1.66 3/ 4 89,375 1,050 525
1.13/16HOMCO SLIMHOLE 1.13/16 1 111,000 900 450
1.13/16 HOMCO FJ 1.13/16 3/ 4 113,000 1,600 800
1.13/16 PRT 1.13/16 3/ 4 110,000 1,595 800
1.13/16 WILSON FJ 1.13/16 3/ 4 113,000 1,600 800
2.1/6 AM MT DSI 2.33 1.1/4 135,036 3,500 1,100
2-1/4 PRT 2.1/4 3/ 4 181,900 4,600 2,300
2-1/4 TSS 2.1/4 1 142,500 2,100 500
2-3/8 AM PAC 2.7/8 1.3/8 238,440 4,800 2,400
2-3/8 AM PAC DSI** 2.7/8 1.1/2 201,900 6,490 3,250
2-3/8 API REG DSI** 3.1/8 1 375,500 8,045 4,020
2-3/8 HOMCO FJ 2.1/2 1 203,100 3,350 1,670
2.3/8 WILSON FJ 2.1/2 1.1/16 138,000 4,490 2,250
2-7/8 AM OH 3.7/8 2 8/53 345,360 8,900 4,450
2.7/8 AM OH Light weight 3.3/4 2 41/93 223,680 5,700 2,850
2-7/8 AM PAC 3.1/8 1.1/2 269,470 5,800 2,900
2-7/8 AM PAC DSI** 3.1/8 1.1/2 269,470 7,290 3,650
3-1/8 PRT 3.1/8 1 323,000 12,285 6,140
3-1/2 AM PAC 3.3/4 2 352,800 8,800 4,400
4-1/4 PRT 4.1/4 2 507,600 26,500 13,250
 Tool Joints 1" - 2-7/8" (Dimension & Strength Data)

Recommended Recom.
Tensile Yield Torsion Yield
Make-up Make-up
Size ConnectionType O.D.(inches) I.D.(inches) Strength Strength
Torque Torque
(pounds) (foot-pounds)
(foot-pounds) (Nm)
1" AM.M.T. 1.9/16 3/4 68.100 765 500 678
1" AM.M.T. 1.9/16 13/16 58.080 650 450 610
1" AM.M.T.-DSI 1.9/16 3/4 68.100 1.300 500 678
1.1/4" AM.M.T. 1.3/4 1 69.698 865 500 678
1.1/4" AM.M.T. 1.3/4 7/8 93.984 1.265 650 881
1.1/4" AM.M.T. 1.3/4 13/16 104.808 1.265 650 881
1.1/4" AM.M.T. 1.3/4 3/4 115.000 1.265 650 881
1.1/4" F.J. (REG.) 2.3/16 5/8 155.300 2.150 1075 1458
1.1/4" AM.M.T.-DSI 1.3/4 7/8 93.984 1.800 650 881
1.1/2" AM.M.T. 2 1 127.100 1.770 950 1288
1.1/2" AM.M.T. 2 1.5/32 92.136 1.285 700 949
1.1/2" AM.M.T. 2 1.1/8 99.528 1.385 750 1017
1.1/2" AM.M.T. 2 1.1/16 113.784 1.585 900 1220
1.1/2" AM.M.T.-DSI 2 1 127.100 2.800 950 1288
1.9/16" HOMCO SLIMLINE 1.9/16 0.937 71.120 900 450 610
1.5/8" BAASH ROSS 1.660 3/4 89.375 1.050 525 712
1.13/16" HOMCO SLIMLINE 1.13/16 1 111.000 900 450 610
1.13/16" HOMCO F.J. 1.13/16 3/4 113.000 1.600 800 1085
1.13/16" PRT 1.13/16 3/4 110.700 1.595 800 1085
1.13/16" WILSON F.J. 1.13/16 3/4 113.000 1.600 800 1085
2.1/16" AM.M.T.-DSI 2.33 1.1/4 135.036 3.500 1.100 1491
2.1/4" PRT 2.1/4 3/4 181.900 4.600 2.300 3118
2.1/4" T.S.S. 2.1/4 1 142.500 2.100 500 678
2.3/8" AM.PAC 2.7/8 1.3/8 238.440 4.800 2.400 3254
2.3/8" AM.PAC-DSI* 2.7/8 1.1/2 201.900 6.490 3.250 4406
2.3/8" API.REG 3.1/8 1 375.500 7.500 3.700 5017
2.3/8" API.REG-DSI * 3.1/8 1 375.500 8.045 4.020 5450
2.3/8" API.IF (= NC26) 3.3/8 1.3/4 313.680 6.800 3.400 4610
2.3/8" HOMCO F.J. 2.1/2 1 203.100 3.350 1.670 2264
2.3/8" WILSON F.J. 2.1/2 1.1/16 138.000 4.490 2.250 3051
2.906 1.805 - - 2.475 3356
2.3/8" PH-6 (C,L,N)** 2.938 1.795 - - 2.475 3356
3.1/8 1.645 - - 2.475 3356
2.906 1.805 - - 3.038 4119
2.3/8" PH-6 (P)** 2.938 1.795 - - 3.038 4119
3.1/8 1.645 - - 3.038 4119
2.7/8" AM.O.H. 3.7/8 2.151 345.360 8.900 4.450 6033
2.7/8" AM.O.H.-Light Weight 3.3/4 2.441 223.680 5.700 2.850 3864
2.7/8" AM.PAC 3.1/8 1.1/2 269.470 5.800 2.900 3932
2.7/8" AM.PAC-DSI* 3.1/8 1.1/2 269.470 7.290 3.650 4949
2.7/8" API.REG 3.3/4 1.1/4 493.600 13.000 6.500 8813
2.7/8" API.IF (= NC31) 4.1/8 2.1/8 447.130 11.800 5.900 7999
2.7/8" Hughes SH(=NC26) 3.3/8 1.3/4 313.680 6.800 3.400 4610
2.7/8" Hughes XH 4.1/4 1.7/8 505.080 13.400 6.700 9084
2.7/8" PH-4 (C,L,N)** 3.3/4 2 - - 5.625 7626
3.3/4 1.945 - - 5.625 7626
2.7/8" PH-4 (P)** 3.3/4 2 - - 7.312 9914
3.3/4 1.945 - - 7.312 9914
3.438 2.265 - - 3.375 4576
2.7/8" PH-6 (C,L,N)** 3.1/2 2.2 - - 3.375 4576
3.5/8 2.13 - - 5.062 6863
3,688 2.03 - - 5.062 6863
2.7/8" Hydrill 533 6.5 ppf 3.1/8 2.200 2983
Hydrill 533 7.9 ppf 3.1/8 2.800 3796
Hydrill 533 8.7 ppf 3.1/8 2.900 3932
3.438 2.265 - - 3.938 5339
2.7/8" PH-6 (P)** 3.1/2 2.2 - - 3.938 5339
3.5/8 2.13 - - 6.188 8390
3,688 2.03 - - 6.188 8390
Strength based on a material yield of 120,000 psi
* Double shouldered internal connection
**Max. Yield Strength C-75: 90,000 psi; L-80: 95,000 psi; N-80: 110,000 psi; P-105: 135,000 psi

TOOLJT.XLS