mep ATV 11 flash corAng 10/07/02 13:23 Page 3

<< Back Telemecanique

Altivar 11
Catalogue Altivar 11 variable speed drives for asynchronous motors
from 0.18 to 2.2 kW

<< Back

Building a New Electric World

 Presentation Variable speed drives
for asynchronous motors 0

Altivar 11
561250

1 2

3 4

5 6

7 8

60250-EN_Ver1.1.fm/2 Schneider Electric

 Presentation (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

Applications
The Altivar 11 is a frequency inverter for 3-phase squirrel cage asynchronous motors
rated between 0.18 kW and 2.2 kW.
There are three types of power supply:
b 100 V to 120 V single phase,
b 200 V to 240 V single phase,
b 200 V to 230 V 3-phase.
The Altivar 11 incorporates specific features for local markets (Europe range,
America range, Asia range) and has functions suitable for the most common
applications, including:
b horizontal materials handling (small conveyors, etc),
b ventilation, pumping, access control, automatic doors,
b special machines (mixers, washing machines, centrifuges, etc).

Functions
The main functions incorporated in the Altivar 11 drive are:
b starting and speed control,
b reversal of operation direction,
b acceleration, deceleration, stopping,
b motor and drive protection,
b 2-wire/3-wire control,
b 4 preset speeds,
b saving the configuration in the drive,
b d.c. injection on stopping,
b ramp switching,
b catching a spinning load,
b local controls (Asia range only).
Several functions can be assigned to one logic input.
Standard versions
The Altivar 11 offer consists of 3 ranges designed for 3 different markets:
b Europe range: ATV 11pUppM2E (items 1 , 2 )
v single phase 240 V power supply,
v positive logic operation,
v integrated class B EMC filter.
b America range: ATV 11pUppppU (items 1 , 2 , 3 , 4 )
v power supplies: 120 V single phase, 240 V single phase or 230 V 3-phase,
v positive logic operation,
v meets current requirement in standard NEC 1999 208 V.
b Asia range: ATV 11pUppppA (items 5 , 6 )
v power supplies: 120 V single phase, 240 V single phase or 230 V 3-phase,
v positive or negative logic operation,
v local controls: Run and Stop keys, and potentiometer.

Altivar 11 drives are supplied either with heatsink (items 1 , 3 , 5 ) for normal
environments and ventilated enclosures, or on a base plate (items 2 , 4 , 6 ) for
mounting on a machine frame, when the size of the frame enables dissipation of the
heat.
Electromagnetic compatibility EMC
The incorporation of EMC filters in ATV 11pUppM2E drives simplifies installation of
machines and provides an economical means of meeting e marking requirements.
ATV 11pUppppU and ATV 11pUppppA drives are available without EMC filter. Filters
are available as an option for customer assembly, if conformity to EMC standards is
required.
Options
The drive only communicates, in point-to-point mode, with the following tools and
software:
b PowerSuite advanced dialogue solution:
v powerSuite software workshop for configuring the drive (item 7 ),
v powerSuite for Pocket PC (item 8 ),
v converter for connecting a PC or a Pocket PC.

The following options can be used with the Altivar 11 drive:

b braking module connected to the drives DC bus,
b braking resistors, for dissipating the energy returned to the drive when the motor
is operating as a generator,
b EMC radio interference input filters,
b plates for mounting on 5 rail,
b adaptor plate for replacing an Altivar 08 drive,
b plate for EMC mounting, earthing the cable shielding.
Characteristics: References: Dimensions: Schemes:
pages 60251/2 to 60251/5 pages 60252/2 to 60252/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

Schneider Electric 60250-EN_Ver1.1.fm/3

 Characteristics Variable speed drives
for asynchronous motors 0

Altivar 11

Environment
Conformity to standards Altivar 11 drives have been developed to conform to the strictest international
standards and the recommendations relating to electrical industrial control devices
(IEC, EN), in particular:
EN 50178, EMC immunity and EMC conducted and radiated emissions.

EMC immunity b IEC/EN 61000-4-2 level 3

b IEC/EN 61000-4-3 level 3
b IEC/EN 61000-4-4 level 4
b IEC/EN 61000-4-5 level 3 (power access)
b IEC/EN 61800-3, environments 1 and 2
EMC conducted and radiated
emissions for drives:
All b IEC/EN 61800-3, environments: 2 (industrial supply) and 1 (public supply) restricted
distribution
ATV 11pU05M2E to b EN 55011, EN 55022 class B, 2 to 12 kHz for motor cable lengths
ATV 11pU18M2E y 5 m and class A (group 1), 2 to 16 kHz for lengths y 10 m
ATV 11pU29M2E to b EN 55011, EN 55022 class B, 4 to 16 kHz for motor cable lengths
ATV 11pU41M2E y 5 m and class A (group 1), 4 to 16 kHz for lengths y 10 m
ATV 11HU05M2E to b With additional EMC filter: EN 55011, EN 55022 class B, 2 to 16 kHz for motor
ATV 11HU41M2E cable lengths y 20 m and class A (group 1), 2 to 16 kHz for lengths y 50 m
ATV 11HU05ppU to b With additional EMC filter: EN 55011, EN 55022 class B, 2 to 16 kHz for motor
ATV 11HU41ppU and cable lengths y 5 m and class A (group 1), 2 to 16 kHz for lengths y 20 m
ATV 11HU05ppA to
ATV 11HU41ppA
e marking The drives bear e marking in accordance with the European low voltage directives
(73/23/EEC and 93/68/EEC) and EMC (89/336/EEC)
Product certification UL, CSA, NOM 117 and C-TICK
Degree of protection IP 20
Vibration resistance Drive without 5 rail option Conforming to IEC/EN 60068-2-6:
- 1.5 mm peak from 3 to 13 Hz
- 1 gn from 13 to 200 Hz
Shock resistance 15 gn for 11 ms conforming to IEC/EN 60068-2-27
593% without condensation or dripping water, conforming to IEC 60068-2-3
Ambient temperature Storage C - 25+ 65
around the unit
Operation C - 10+ 40,
- 10+ 50 : removing the protective cover from the top of the drive
Up to + 60 with current derating of 2.2% per C above 50 C
Maximum operating altitude m 1000 without derating (above this, derate the current by 1% per additional 100 m)
Operating position
Maximum permanent angle in relation to the normal vertical
mounting position

Drive characteristics
Output frequency range Hz 0200
Switching frequency kHz 216
Speed range 120
Transient overtorque 150% of the nominal motor torque
Braking torque - 20% of the nominal motor torque without braking resistor at no-load with the
deceleration ramp adaptation function enabled
- 80% of the nominal motor torque with braking resistor (available as an option) at no-
load
- Up to 150% of the nominal motor torque with braking resistor (available as an option)
at high inertia
Maximum transient current 150% of the nominal drive current for 60 seconds
Voltage/frequency ratio Sensorless flux vector control with PWM motor control signal (1)
Factory-set for most constant torque applications
Frequency loop gain Factory-set with the speed loop stability and gain
Possible correction for machines with high resistive torque or high inertia, or for
machines with fast cycles
Slip compensation Factory-set, according to the rating of the drive (adjustment possible)
(1) Pulse width modulation

Presentation: References: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60252/2 to 60252/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

60251-en_Ver2.0.fm/2 Schneider Electric

Characteristics (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

Electrical characteristics
Power supply Voltage V 200 - 15% to 240 + 10% single phase for ATV 11pUpp M2p
200 - 15% to 230 + 15% 3-phase pour ATV 11pUpp M3p
100 - 15% to 120 + 10% single phase for ATV 11pUpp F1p
Frequency Hz 50 5% or 60 5%

Isc A 1000 (prospective short-circuit current at the connection point) for single phase
power supply
5000 (prospective short-circuit current at the connection point) for 3-phase power
supply
Output voltage Maximum 3-phase voltage equal to:
- the line supply voltage for ATV 11pUppMpp
- double the line supply voltage for ATV 11pUppF1 p
Maximum connection capacity Drive ATV 11pU05 ppp, U09 ppp , 1.5 mm 2 (AWG 14)
of the power supply, the motor U12Mpp, U18M pp
and the braking module Drive ATV 11p 4 mm2 (AWG 10)
U18F1p, U29 ppp, U41 ppp
Max. length of motor cables m - 50, shielded cable
- 100, non-shielded cable
Electrical isolation Electrical isolation between power and control (inputs, outputs, power supplies)
Available internal supplies Short-circuit and overload protection:
- One + 5 V (0/+ 5%) supply for the reference potentiometer (2.2 to 10 kW), maximum
current 10 mA
- One + 15 V ( 15%) supply for the control inputs, maximum current 100 mA
Analog input AI1 1 configurable analog input
Max. sampling time: 20 ms, resolution 0.4%, linearity 5%:
- voltage 0-5 V (internal power supply only) or 0-10 V, impedance 40 kW
- current 0-20 mA or 4-20 mA (without addition of a resistor), impedance 250 W
Logic inputs LI 4 assignable logic inputs, impedance 5 kW
+ 15 V internal or 24 V external power supply (min. 11 V, max. 30 V).
Factory-set with 2-wire control in transition mode for machine safety, for Europe and
America ranges:
- LI1: forward
- LI2: reverse
- LI3/LI4: 4 preset speeds
- Local controls for the Asia range
Multiple assignment makes it possible to mix several functions on one input (example:
LI1 assigned to forward and preset speed 2
LI3 assigned to reverse and preset speed 3)
Positive logic State 0 if < 5 V, state 1 if > 11 V
Max. sampling time: 20 ms
Negative logic Available by programming on the Asia range only
State 0 if > 11 V or logic input not wired, state 1 if < 5 V
Max. sampling time: 20 ms
DO output Factory setting:
- 2 kHz PWM (1) open collector output. Can be used for electromagnetic
galvanometer
- Max. current 10 mA
- Output impedance 1 kW, linearity 1%, max. sampling time 20 ms.
Assignable as logic output:
- Open collector logic output, output impedance 100 W, 50mA max
- Internal voltage (see above, available internal supplies)
- External voltage 30 V max: 50 mA
Relay outputs (RA-RC) 1 protected relay logic output (contact open on fault).
Minimum switching capacity: 10 mA for c 24 V.
Maximum switching capacity:
b On resistive load (cos j = 1 and L/R = 0 ms): 5 A for a 250 V or c 30 V
b On inductive load (cos j = 0.4 and L/R = 7 ms): 2 A for a 250 V or c 30 V
Maximum I/O connection capacity 1.5 mm 2 (AWG 14)
Acceleration and deceleration ramps Ramp profiles: linear from 0.1 to 99.9 s.
Automatic adaptation of deceleration ramp time if braking capacities exceeded,
possible inhibition of this adaptation (use of braking module).
Braking to a standstill By d.c. injection: automatically to a standstill as soon as the frequency drops to zero.
Period adjustable from 0.1 to 30 s or continuous, current adjustable from 0 to 1.2 In
Main protection and safety features of the drive b Thermal protection against overheating
b Protection against short-circuits between output phases
b Protection against overcurrent between output phases and earth, at power-up only
b Line supply overvoltage and undervoltage safety circuits
b Line supply phase loss safety function, for 3-phase supply.
Motor protection Thermal protection integrated in the drive by continuous calculation of the l2t.
Thermal memory reset on power down.
Insulation resistance to earth MW > 500 (electrical isolation)
Frequency resolution Display units: 0.1 Hz
Analog inputs: 0.1 Hz for 200 Hz max.
Time constant for reference change ms 5
(1) Pulse width modulation

Presentation: References: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60252/2 to 60252/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

Schneider Electric 60251-en_Ver2.0.fm/3

 Characteristics, Special Variable speed drives
uses for asynchronous motors 0

Altivar 11

Torque characteristics (typical curves)

The curves below define the available continuous torque and transient overtorque for
both force-cooled and self-cooled motors. The only difference is in the ability of the
motor to provide a high continuous torque at less than half the nominal speed.

T/Tn
2
4
1,7

1,5
3
1,25

1
2

0,75
1

0,5

0,25

0 N (Hz)
0 12 25 37 50 75 100
0 15 30 45 60 90 120

1 Self-cooled motor: continuous useful torque

2 Force-cooled motor: continuous useful torque
3 Transient overtorque in factory settings, when motor is warm.
4 Transient overtorque in optimised settings, when motor is warm.

Special uses
Use with a motor with a different rating to that of the drive
The device can supply any motor which has a power rating lower than that for which
it is designed.
For motor ratings slightly higher than that of the drive, check that the current
absorbed does not exceed the permanent output current of the drive.

Connecting motors in parallel

The rating of the drive must be greater than or equal to the sum of the currents of the
motors to be connected to the drive. In this case, provide external thermal protection
for each motor using thermal probes or relays.
If the number of motors in parallel is greater than or equal to 3, it is advisable to install
a 3-phase choke between the drive and the motors.
Note: For the references of the chokes, please consult your Regional Sales Office.

Presentation: References: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60252/2 to 60252/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

60251-en_Ver2.0.fm/4 Schneider Electric

Combinations Variable speed drives
for asynchronous motors 0

Altivar 11

Combinations for self-assembly

Function: to protect persons and equipment from any level of overcurrent which may
be encountered (overload or short-circuit).

Standard power Speed drive Circuit-breaker Contactor

ratings of 3-phase Reference (1) Telemecanique Adjustment Max. Reference
4-pole 50/60 Hz (2) range short-
motors circuit
Merlin Gerin Rating current
Icu
kW A kA
M1 A1 Q1 KM1
Single-phase supply voltage: 100120 V 50/60 Hz
0.18 ATV 11HU05F1 p GV2 pp14 6...10 > 100 LC1 D09
DT40 10 6 LC1 D09
0.37 ATV 11 pU09F1p GV2 pp14 6...10 > 100 LC1 D12
DT40 16 6 LC1 D12
0.75 ATV 11HU18F1 p GV2 pp21 17...23 50 LC1 D25
DT40 20 6 LC1 D25
Single-phase supply voltage: 200240 V 50/60 Hz
0.18 ATV 11HU05M2 p GV2 pp08 2.5...4 > 100 LC1 D09
DT40 6 6 LC1 D09
0.37 ATV 11 pU09M2p GV2 pp14 6...10 > 100 LC1 D09
DT40 10 6 LC1 D09
0.55 ATV 11 pU12M2E GV2 pp14 6...10 > 100 LC1 D09
DT40 10 6 LC1 D09
0.75 ATV 11 pU18M2p GV2 pp16 9...14 > 100 LC1 D12
DT40 16 6 LC1 D12
1.5 ATV 11HU29M2E GV2 pp20 13...18 50 LC1 D25
DT40 20 6 LC1 D25
1.5 ATV 11HU29M2U GV2 pp21 17...23 50 LC1 D25
ATV 11HU29M2A DT40 20 6 LC1 D25
2.2 ATV 11HU41M2 p GV2 pp22 20...25 50 LC1 D32
DT40 32 6 LC1 D32
3-phase supply voltage: 200230 V 50/60 Hz
0.18 ATV 11HU05M3 p GV2 pp07 1.6...2.5 > 100 LC1 D09
DT40 6 6 LC1 D09
0.37 ATV 11 pU09M3p GV2 pp08 2.5...4 > 100 LC1 D09
DT40 6 6 LC1 D09
0.75 ATV 11 pU18M3p GV2 pp14 6...10 > 100 LC1 D09
DT40 10 6 LC1 D09
1.5 ATV 11HU29M3 p GV2 pp16 9...14 > 100 LC1 D12
DT40 16 6 LC1 D12
2.2 ATV 11HU41M3 p GV2 pp20 13...18 50 LC1 D25
DT40 20 6 LC1 D25

Combinations of circuit-breakers and add-on modules

DT40 Vigi TG40
Rating (A) Rating (A) Type (3) Sensitivity
6 25 A "si" 30 mA
10 25 A "si" 30 mA
16 25 A "si" 30 mA
20 25 A "si" 30 mA
32 40 A "si" 30 mA
Recommendations for special uses:
b All RH10 / RH21 / RH99 / RHU residual current protection devices with separate sensors are
compatible as long as the type and sensitivity of the add-on modules given in the table above
are observed.
b It is advisable to connect one residual current differential safety device per drive. In this case
a type B device must not be located downstream of a type A or AC device.
(1) Replace the dots in the reference according to the type of drive required, see pages 60252/2
to 60252/4.
(2) Replace the dots with ME for pushbutton control or with P for control via rotating knob.
Type 2 coordination is provided by combining a GV2 circuit breaker with an LC1 Dpp
contactor.
(3) For additional protection against direct contact, the add-on module must be type B with a
sensitivity of 30 mA, if the following conditions are met :
- 3-phase power supply, all neutral point connection systems and
- the braking resistor must be accessible.

Presentation: References: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60252/2 to 60252/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

Schneider Electric 60251-en_Ver2.0.fm/5

 References Variable speed drives
for asynchronous motors 0

Altivar 11
ATV 11ppppppE Europe range

Drives with heatsink (frequency range from 0 to 200 Hz)

Motor Line supply Altivar 11
(1)
Power Max. line Permanent Max. Power Reference Weight
indicated current for output transient dissipated (4)
on prospective current (2) current (3) at nominal
plate Isc load
1 kA
550483

kW A A A W kg
Single phase supply voltage: 200240 V 50/60 Hz
0.18 2.9 1.1 1.6 12 ATV 11HU05M2E 0.900

0.37 5.3 2.1 3.1 20.5 ATV 11HU09M2E 1.000

0.55 6.3 3 4.5 29 ATV 11HU12M2E 1.100

ATV 11 HU18M2E

0.75 8.6 3.6 5.4 37 ATV 11HU18M2E 1.100

550485

1.5 14.8 6.8 10.2 72 ATV 11HU29M2E 1.800

(5)

2.2 20.8 9.6 14.4 96 ATV 11HU41M2E 1.800

(5)

Drives on base plate (frequency range from 0 to 200 Hz)

Motor Line supply Altivar 11
(1)
ATV 11 PU18M2E
Power Max. line Permanent Max. Power Reference Weight
indicated current for output transient dissipated (4)
on prospective current (2) current (3) at nominal
plate Isc load
1 kA
kW A A A W kg
Single phase supply voltage: 200240 V 50/60 Hz
0.37 5.3 2.1 3.1 20.5 ATV 11PU09M2E 0.900
550489

0.55 6.3 3 4.5 29 ATV 11PU12M2E 0.900

0.75 8.6 3.6 5.4 37 ATV 11PU18M2E 0.900

(1) Line voltage 230 V.

(2) The current value is given for a 4 kHz switching frequency.
(3) For 60 seconds.
ATV 11 HU41M2E (4) Drive supplied with an integrated EMC filter which cannot be disconnected.
(5) With integrated fan.

Presentation: Characteristics: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

60252-en_Ver1.1.fm/2 Schneider Electric

 References Variable speed drives
for asynchronous motors 0

Altivar 11
ATV 11ppppppU America range

Drives with heatsink (frequency range from 0 to 200 Hz)

Motor Line supply Altivar 11
550484

Power Max. line Permanent Max. Power Reference Weight

indicated current (1) output transient dissipated (4)
on current (2) current (3) at nominal
plate load
kW/HP A A A W kg
Single phase supply voltage: 100120 V 50/60 Hz
0.18/0.25 6 1.6 2.4 14.5 ATV 11HU05F1U 0.900

0.37/0.5 9 2.4 3.6 23 ATV 11HU09F1U 1.000

0.75/1 18 4.6 6.3 43 ATV 11HU18F1U 1.800

ATV 11HU18M2U
(5)
Single phase supply voltage: 200240 V 50/60 Hz
0.18/0.25 3.3 1.6 2.4 14.5 ATV 11HU05M2U 0.900

0.37/0.5 6 2.4 3.6 23 ATV 11HU09M2U 1.000

0.75/1 9.9 4.6 6.3 43 ATV 11HU18M2U 1.100

550486

(5)
1.5/2 17.1 7.5 11.2 77 ATV 11HU29M2U 1.800
(5)
2.2/3 24.1 10.6 15 101 ATV 11HU41M2U 1.800
(5)
3-phase supply voltage: 200230 V 50/60 Hz
0.18/0.25 1.8 1.6 2.4 13.5 ATV 11HU05M3U 0.900

0.37/0.5 3.6 2.4 3.6 24 ATV 11HU09M3U 1.000

ATV 11PU18M2U 0.75/1 6.3 4.6 6.3 38 ATV 11HU18M3U 1.100

(5)
1.5/2 11 7.5 11.2 75 ATV 11HU29M3U 1.800
(5)
2.2/3 15.2 10.6 15 94 ATV 11HU41M3U 1.800
(5)
Drives on base plate (frequency range from 0 to 200 Hz)
550490

Motor Line supply Altivar 11

Power Max. line Permanent Max. Power Reference Weight
indicated current (1) output transient dissipated (4)
on current (2) current (3) at nominal
plate load
kW/HP A A A W kg
Single phase supply voltage: 100120 V 50/60 Hz
0.37/0.5 9 2.4 3.6 23 ATV 11PU09F1U 0.900

Single phase supply voltage: 200240 V 50/60 Hz

0.37/0.5 6 2.4 3.6 23 ATV 11PU09M2U 0.900
ATV 11HU41M2U
0.75/1 9.9 4.6 6.3 43 ATV 11PU18M2U 0.900

3-phase supply voltage: 200230 V 50/60 Hz

0.37/0.5 3.6 2.4 3.6 24 ATV 11PU09M3U 0.900

0.75/1 6.3 4.6 6.3 38 ATV 11PU18M3U 0.900

550491

(1) The line current value is given for the measurement conditions indicated in the table below.
Drive rating Prospective Isc Line voltage
ATV 11pUF1U 1 kA 100 V
ATV 11pUM2U 1 kA 208 V
ATV 11pUM3U 5 kA 208 V
(2) The current value is given for a 4 kHz switching frequency.
(3) For 60 seconds.
(4) Drive supplied without EMC filter. To order an EMC filter separately, see page 60252/5.
(5) With integrated fan.

ATV 11HU41M3U

Presentation: Characteristics: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

Schneider Electric 60252-en_Ver1.1.fm/3

 References Variable speed drives
for asynchronous motors 0

Altivar 11
ATV 11ppppppA Asia range

Drives with heatsink (frequency range from 0 to 200 Hz)

Motor Line supply Altivar 11
550488

Power Max. line Permanent Max. Power Reference Weight

indicated current (1) output transient dissipated (4)
on current (2) current (3) at nominal
plate load
kW A A A W kg
Single phase supply voltage: 100120 V 50/60 Hz
0.18 6 1.4 2.1 14 ATV 11HU05F1A 0.900

0.37 9 2.4 3.6 25 ATV 11HU09F1A 1.000

ATV 11HU18M2A 0.75 18 4 6 40 ATV 11HU18F1A 1.800

(5)
Single phase supply voltage: 200240 V 50/60 Hz
0.18 3.3 1.4 2.1 14 ATV 11HU05M2A 0.900

0.37 6 2.4 3.6 25 ATV 11HU09M2A 1.000

550487

0.75 9.9 4 6 40 ATV 11HU18M2A 1.100

1.5 17.1 7.5 11.2 78 ATV 11HU29M2A 1.800

(5)
2.2 24.1 10 15 97 ATV 11HU41M2A 1.800
(5)
3-phase supply voltage: 200230 V 50/60 Hz
0.18 1.8 1.4 2.1 13.5 ATV 11HU05M3A 0.900

0.37 3.6 2.4 3.6 24 ATV 11HU09M3A 1.000

ATV 11PU18M2A 0.75 6.3 4 6 38 ATV 11HU18M3A 1.100

1.5 11 7.5 11.2 75 ATV 11HU29M3A 1.800

(5)
2.2 15.2 10 15 94 ATV 11HU41M3A 1.800
(5)
Drives on base plate (frequency range from 0 to 200 Hz)
550492

Motor Line supply Altivar 11

Power Max. line Permanent Max. Power Reference Weight
indicated current (1) output transient dissipated (4)
on current (2) current (3) at nominal
plate load
kW A A A W kg
Single phase supply voltage: 100120 V 50/60 Hz
0.37 9 2.4 3.6 25 ATV 11PU09F1A 0.900

Single phase supply voltage: 200240 V 50/60 Hz

0.37 6 2.4 3.6 25 ATV 11PU09M2A 0.900
ATV 11HU41M2A
0.75 9.9 4 6 40 ATV 11PU18M2A 0.900

3-phase supply voltage: 200230 V 50/60 Hz

0.37 3.6 2.4 3.6 24 ATV 11PU09M3A 0.900

0.75 6.3 4 6 38 ATV 11PU18M3A 0.900

550493

(1) The line current value is given for the measurement conditions indicated in the table below.
Drive rating Prospective Isc Line voltage
ATV 11pUF1A 1 kA 100 V
ATV 11pUM2A 1 kA 200 V
ATV 11pUM3A 5 kA 200 V
(2) The current value is given for a 4 kHz switching frequency.
(3) For 60 seconds.
(4) Drive supplied without EMC filter. To order an EMC filter separately, see page 60252/5.
(5) With integrated fan.

ATV 11HU41M3A

Presentation: Characteristics: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

60252-en_Ver1.1.fm/4 Schneider Electric

 References Variable speed drives
for asynchronous motors 0

Altivar 11

Options and accessories

Description For drives Reference Weight
550496

kg
Advanced dialogue solution All ratings See page 60200/3
PowerSuite

Converter, for connecting a PC or All ratings VW3 A11301 0.070

Pocket PC, equipped with PowerSuite
software
EMC input filters ATV 11HU05M2E VW3 A11401 0.650
ATV 11HU09M2E
ATV 11HU12M2E
ATV 11HU18M2E
ATV 11HU05F1U/A
ATV 11HU09F1U/A
ATV 11HU05M2U/A
ATV 11HU09M2U/A
ATV 11HU18M2U/A

VW3 A5870p ATV 11HU29M2E VW3 A11402 0.850

ATV 11HU41M2E
ATV 11HU18F1U/A
ATV 11HU29M2U/A
ATV 11HU41M2U/A

ATV 11HU05M3U/A VW3 A11403 0.650

ATV 11HU09M3U/A
ATV 11HU18M3U/A

ATV 11HU29M3U/A VW3 A11404 0.850

ATV 11HU41M3U/A
550497

Braking module connected to the All ratings VW3 A11701 0.250

DC bus

Braking resistors Not protected ATV 11pU05 ppp (1) VW3 A58702 0.600
(IP 00) ATV 11pU09 ppp (1)
ATV 11pU12 ppp (1)
ATV 11pU18 ppp (1)
ATV 11pU29 ppp (2)

ATV 11pU41 ppp (2) VW3 A58704 0.600

Protected ATV 11pU05 ppp (1) VW3 A58732 2.000

(IP 30) ATV 11pU09 ppp (1)
ATV 11pU12 ppp (1)
ATV 11pU18 ppp (1)
ATV 11pU29 ppp (2)

ATV 11pU41 ppp (2) VW3 A58733 2.000

Plates for mounting on 5 rail ATV 11pU05 ppp VW3 A11851 0.220
(width 35 mm) ATV 11pU09 ppp
VW3 A5873p ATV 11pU12 ppp
ATV 11pU18Mpp

ATV 11HU18F1p VW3 A11852 0.300

ATV 11pU29 ppp
ATV 11pU41 ppp

Adaptor plate for replacing Altivar 08 All ratings VW3 A11811 0.220

Earthing plate for EMC mounting All ratings VW3 A11831 0.100
550494

Ventilation kit (3) ATV 11HU18F1p VW3 A11821 0.070

ATV 11HU18MpU
ATV 11HU29ppp
ATV 11HU41ppp

(1) Minimum value of the resistor to be connected: 75 ohms.

(2) Minimum value of the resistor to be connected: 51 ohms.
(3) "Low noise" fan.

VW3 A11852

Presentation: Characteristics: Dimensions: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60253/2 and 60253/3 pages 60254/2 and 60254/3

Schneider Electric 60252-en_Ver1.1.fm/5

 Dimensions Variable speed drives
for asynchronous motors 0

Altivar 11

ATV 11HU05ppE/U/A, ATV 11PUppppE/U/A ATV 11HU09M2E

5,5
=
2x

142

120
H
b

c G
=
125 = 60 =

16,5
= =
a 72
ATV 11 a b c G H
HU05ppE/U, 72 142 101 601 1311 5
PUppppE/U
HU05ppA, 72 142 108 601 1311 5
PUppppA
ATV 11HU09ppU/A ATV 11HU12M2E, ATV 11HU18M2E

5,5
=

2x
142

120
H
b

c G 138 = 60 =

16,5
=

= =
a 72
ATV 11 a b c G H
HU09ppU 72 142 125 601 1311 5
HU09ppA 72 142 132 601 1311 5
ATV 11HU18MpU/A ATV 11HU18F1U/A, ATV 11HU29MpE/U/A, ATV 11HU41MpE/U/A
=

2x 4x
b

b
H

c G c = G =
=
=

= =
a a

ATV 11 a b c G H ATV 11 a b c G H
HU18MpU 72 147 138 601 1311 5 HU18F1U, HU29MpE/U, HU41MpE/U 117 142 156 1060,5 1311 5
HU18MpA 72 142 145 601 1311 5 HU18F1A, HU29MpA, HU41MpA 117 142 163 1060,5 1311 5
EMC input filters VW3 A11401 to A11404 Protected braking resistors Non protected braking resistors VW3
VW3 A58732 and A58733 A58702 and A58704
(2-wire output, length 0.5 m)
=

154
170
8,5
H
b

310

30 = 40 =
332

60
Braking module VW3 A11701
(for mounting on AM1-ED rail)
c = G =
a
90

VW3 a b c G H
61 = =
=

A11401 75 194 30 61 180

A11402 117 184 40 97 170 85 73 45
A11403 75 194 40 61 180
A11404 117 190 40 97 170

Presentation: Characteristics: References: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60252/2 to 60252/5 pages 60254/2 and 60254/3

60253-EN_Ver1.3.fm/2 Schneider Electric

Dimensions, Variable speed drives
mounting for asynchronous motors 0

Altivar 11

ATV 08 adaptor plate VW3 A11811 Plates for mounting on 7 rail VW3 A11851 and A11852
142

143,6

143,6
32,9 77,5 37,9 77,5 39,9 122,8

EMC earthing plate VW3 A11831 Ventilation kit VW3 A11821

(1)

59,9
(2)
61

23,3 59
15 67,6
(1) 2 screws supplied for fixing the earthing plate.
(2) 5 x M4 mm screws for fixing EMC clamps.
Mounting recommendations
b Install the unit vertically, at 10.
b Do not place it close to heating elements.
b Leave sufficient free space to ensure that the air required for cooling purposes can circulate, by natural convection or by ventilation, from the
bottom to the top of the unit.
b Free space in front of unit: 10 mm minimum.

-10 C to 40 C
d 50 mm: no special precautions.
d = 0 (mounted side by side): remove the protective cover from the top of the drive.
40 C to 50 C
d 50 mm: remove the protective cover from the top of the drive.
50 C to 60 C
d 50 mm: remove the protective cover from the top of the drive, and derate the
nominal current of the drive by 2.2% per C above 50 C.

Recommendations for mounting on a machine frame (specific to ATV 11PUppppp drives)

ATV 11Ppppppp drives can be mounted on (or in) a steel or aluminium machine
(1) frame, observing the following conditions:

b maximum ambient temperature: 40 C,

b vertical mounting 10,
b the drive must be fixed at the centre of a support (frame) which is a minimum of
10 mm thick and with a minimum cooling area of 0.12 m2 for steel and 0.09 m2 for
aluminium, exposed to the open air,
(2) b support area for the drive (142 x 72 min) machined on the frame with a surface
smoothness of 100 mm max and an unevenness of 3.2 mm max,
b mill the tapped holes lightly in order to remove any burrs,
b coat the whole drive support area with thermal contact grease (or equivalent).

When the operating conditions are close to the maximum limits (power, cycle and
temperature), this type of use must be checked beforehand, by monitoring the
thermal state of the drive.

(1) 2 x M4 tapped holes.

(2) Minimum machined area

Presentation: Characteristics: References: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60252/2 to 60252/5 pages 60254/2 and 60254/3

Schneider Electric 60253-EN_Ver1.3.fm/3

 Schemes Variable speed drives
for asynchronous motors 0

Altivar 11

Schemes with contactor

3-phase power supply ATV 11ppppM3p Single phase power supply ATV 11ppppF1p and ATV
11ppppM2p

200240 V 50/60 Hz 100...120 V 50/60 Hz and 200...240 V 50/60 Hz

5
1

Q1 Q1

6
2

(4)

3
1

(4)
KM1 KM1

4
2

(1) (2) (3) (1) (2) (3)

A1 A1

L1

N/L2

RA

RC

LI1

LI2

LI3

LI4

+ 15 V
DO
L1

L2

L3

RA

RC

LI1

LI2

LI3

LI4

+ 15 V
DO

+5V
+5V

PA/+
PA/+

PC/
PC/

AI1

0V
AI1

0V

W
W

U
U

V
V

W1
W1

U1

V1
U1

V1

A2 A2

+
+

(5) Potentiometer (5) Potentiometer

M1 M1

PA

PB
PA

PB

speed speed
3 3 0 -20 mA
reference 0 -20 mA reference
or or
4 -20 mA 4 -20 mA
Braking Braking
resistor resistor
0-10 V 0-10 V
(external power supply) (external power supply)

2-wire control 3-wire control Analog voltage input Analog current input
External 10 V use 0-20 mA or 4-20 mA

ATV 11 control terminals ATV 11 control terminals ATV 11 control terminals ATV 11 control terminals
+ 15 V

+ 15 V
LI1

LI1

LI2
LIx

LIx

AI1

0V
AI1

0V

Speed Source
LI1: Forward LI1: Stop reference 0 -20 mA
LIx: Reverse LI2: Forward potentiometer or
LIx: Reverse 2.2 to 10 k 4 -20 mA

For combinations of KM1, Q1, etc, components (see the table on page 60251/5).

(1) Fault relay contact: for remote signalling of drive status.

(2) Internal +15 V. If an external +24 V supply is used, connect the 0 V on the external supply to the 0 V terminal, do not use the + 15 terminal on the drive, and
connect the common of the LI inputs to the + 24 V of the external supply.
(3) DO output: can be configured as an analog or a logic output. Internal voltage + 15 V or external + 24 V.
(4) Galvanometer or low level relay.
(5) Braking module VW3 A11701, if braking resistor VW3 A587pp is used.
Note: Fit interference suppressors to all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent
lighting, etc.

Presentation: Characteristics: References: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60252/2 to 60252/5 pages 60254/2 and 60254/3

60254-EN_Ver1.2.fm/2 Schneider Electric

Connection Variable speed drives
for asynchronous motors 0

Altivar 11
Electromagnetic compatibility

Connections to meet the requirements of EMC standards

Principle

b Earths between the drive, the motor and the cable shielding must have "high frequency" equipotentiality.
b Use shielded cables with shielding connected to earth at 360 at both ends for the motor cables, and if necessary the braking module and
resistor and control-signalling cables. Conduit or metal ducting can be used for part of the shielding length provided that there is no break in
continuity.
b Ensure maximum separation between the power supply cable (line supply) and the motor cable.

Installation diagram for ATV 11pUppppE/U/A

3 1 Earthing plate VW3 A11831 to be fitted on the drive.

2 Altivar 11.
3 Non-shielded power supply cable.
4 Non-shielded cable for fault relay contacts output.
5 Fix and earth the shielding of cables 6 and 7 as close as possible to the drive:
- strip the shielding,
- use cable clamps of an appropriate size on the parts from which the shielding
has been stripped, to attach them to the earthing plate,
- the shielding must be clamped tightly enough to the earthing plate to ensure
2 good contact,
- types of clamp: non-oxidizing metal.
6 Shielded cable (1) for connecting the motor.
7 Shielded cable (1) for connecting the control/signalling system. For applications
which require a large number of conductors, small cross-sections must be used
(0.5 mm2).
8 PE cable.
4
(1) The shielding of cables (6, 7 and 8) must be connected to earth at both ends.
The shielding must be continuous and if intermediate terminals are used, they must be in EMC
1 5 metal boxes.

7 6

8
Note: If using an additional input filter, it must be mounted under the drive and connected directly to the line supply via a non-shielded cable. Link 3 on the drive is
then via the filter output cable.
Although there is an HF equipotential earth connection between the drive, the motor and the cable shielding, it is still necessary to connect the PE protective
conductors (green-yellow) to the appropriate terminals on each of the devices.

Presentation: Characteristics: References: Schemes:

pages 60250/2 and 60250/3 pages 60251/2 to 60251/5 pages 60252/2 to 60252/5 pages 60254/2 and 60254/3

Schneider Electric 60254-EN_Ver1.2.fm/3

 Functions Variable speed drives
for asynchronous motors 0

Altivar 11

Summary of functions
Operating speed range page 60255/3
Acceleration and deceleration ramp times page 60255/3
Second ramp page 60255/3
Deceleration ramp adaptation page 60255/3
Preset speeds page 60255/4
Configuration of analog input AI1 page 60255/4
Analog or logic output DO page 60255/4
Forward/reverse operation page 60255/4
2-wire control page 60255/5
3-wire control page 60255/5
Automatic d.c. injection page 60255/5
Switching frequency, noise reduction page 60255/5
Fault relay, unlocking page 60255/5
Fault reset page 60255/6
Automatic restart page 60255/6
Automatic catching a spinning load with speed detection page 60255/6
Controlled stop on loss of line supply page 60255/6
Drive thermal protection page 60255/6
Motor thermal protection page 60255/6
Monitoring page 60255/7
Incompatible functions page 60255/7
Functions specific to the Asia range page 60255/7
Drive factory setting
To facilitate the setting up of the drive, the functions have been programmed to the meet the
requirements of the most common applications.

Drive functions and I/O :

b 2-wire control on transition
v Logic input LI1 : forward
v Logic input LI2 : reverse
b Preset speeds:
v Logic input LI3 : preset speeds
v Logic input LI4 : preset speeds
b Analog input AI1 : 0-5 V speed reference
b Logic/analog output DO : motor frequency (analog)
b Deceleration ramp adaptation
b Automatic d.c. current injection for 0.5 s to standstill.

Functions of the display and the keys

Altivar 11

ESC ENT 4

2
5 RUN STOP 6

1 Information is displayed in the form of codes or values in three "7-segment"

displays
2 Buttons for scrolling through the menus or modifying values
3 ESC : Button for exiting the menus (no confirmation).
4 ENT : Validation button for entering a menu or confirming the new value selected

b Only on the Asia range:

5 RUN : Local control of motor operation.
6 STOP : Local control of motor stopping.
7 Speed reference potentiometer.

60255-en_Ver1.1.fm/2 Schneider Electric

Functions (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

b Operating speed range

Used to determine 2 frequency limits which define the speed range permitted by the machine
under actual operating conditions.

f (Hz)

HSP LSP : low speed, from 0 to HSP, factory setting 0

HSP : high speed, from LSP to 200 Hz, factory setting 50/60

LSP
Reference
0V 5V
0V 10 V (external power supply)
0 mA 20 mA
4 mA 20 mA

b Acceleration and deceleration ramp times

Used to define acceleration and deceleration ramp times according to the application and the
machine dynamics

f (Hz) f (Hz)

50/60 50/60

0 t 0 t
t1 t2
Linear acceleration ramp Linear deceleration ramp
Adjustment of t1 : 0.1 to 99.9 s Adjustment of t2 : 0.1 to 99.9 s
factory setting 3 s. factory setting 3 s.

b Second ramp
Used to switch 2 acceleration or deceleration ramp times, which can be adjusted separately.
Enabled by means of 1 reassignable logic input.
It is suitable for machines with fast continuous speed correction and high speed lathes with
acceleration and deceleration limiting above certain speeds.

f(Hz)

HSP Acceleration 1 (Acc 1) and

Acc 2 Dec 2 deceleration 1 (Dec 1) :
- adjustment 0.1 to 99.9 s
- factory setting 3 s

Acc 1 Dec 1 Acceleration 2 (Acc 2) and

t deceleration 2 (Dec 2) :
- adjustment 0.1 to 99.9 s
- factory setting 5 s

Forward HSP : high speed

or 1
Adjustment of second ramp with reverse 0 t
Pocket PC PowerSuite

1
LI4 0 t

Example of switching using logic input LI4

b Deceleration ramp adaptation

Used to automatically increase the deceleration ramp time if the initial setting is too low when the
load inertia is taken into account. This function prevents the drive locking if there is an
overvoltage on deceleration fault.
If this function is disabled, an appropriate braking module and resistor can be used.

Schneider Electric 60255-en_Ver1.1.fm/3

 Functions (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

b Preset speeds
Used to switch preset speed references.
Choice between 2 or 4 preset speeds.
Enabled via 1 or 2 logic inputs.
The preset speeds can be adjusted in increments of 0.1 Hz from 0 Hz to 200 Hz.
They take priority over the reference given via the analog input or, for the Asia range, on the
drives potentiometer.

f (Hz)
The speed obtained with inputs
LIx and LIy at state 0 is LSP or the
speed reference, depending on
the level of analog input AI1.

Factory settings :
LSP
1st speed : LSP (low speed or
t reference)

Adjusting the preset speeds with the PowerSuite 1 2nd speed : 10 Hz

software workshop for PC LI1 0 t 3rd speed : 25 Hz

1 4th speed : 50 Hz

LIx 0 t

LIy 0
Example of operation with 4 preset speeds.

b Configuration of analog input AI1

This is used to modify the specifications, for either voltage or current, of analog input AI1.
Factory setting : 0-5 V (internal power supply only).
Other possible values via external power supplies : 0-10 V, 0-20 mA, 4-20 mA.
Analog voltage input Analog current input
External 10 V use 0-20 mA or 4-20 mA use

Altivar 11 control terminals Altivar 11 control terminals

AI1

0V

AI1

0V
Speed Supply
0-20 mA
reference
potentiometer or
2.2 to 10 kW 4-20 mA

b Analog or logic output DO

Output DO can be programmed to be a logic output or an analog output. It enables remote
signalling of the following information as required :
v Frequency threshold reached (logic output)
v Reference reached (logic output)
v Current threshold reached (logic output)
v Current in the motor (analog output)
v Motor frequency (analog output)

Diagram with internal power supply Diagram with external power supply

Altivar 11 control terminals Altivar 11 control terminals

+ 15 V

0V

DO
DO

Z Z
+U
0V

Power supply

If it is a logic output: Z is a relay or a low level input.

If it is an analog output: Z can be, for example, a galvanometer.
For a galvanometer with resistance R, the maximum voltage supplied will be :
R ( W)
Ux --------------------------------------------
R ( W ) + 1000 ( W )

b Direction of operation : forward/reverse

In 2-wire control, forward operation cannot be reassigned to any logic input other than LI1.
In 3-wire control, stopping cannot be reassigned to any logic input other than LI1, and forward
operation cannot be reassigned to any logic input other than LI2.
Reverse operation can be disabled for applications with a single direction of motor rotation, by
not assigning any logic input to reverse operation.

60255-en_Ver1.1.fm/4 Schneider Electric

Functions (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

b 2-wire control
Used to control the direction of operation by means of a maintained contact.
Run (forward or reverse) and stop are controlled by the same logic input.
Enabled by means of 1 or 2 logic inputs (one or two directions).
This function is suitable for all non-reversing and reversing applications.
3 operating modes are possible :
v detection of the state of the logic inputs
v detection of a change in state of the logic inputs
v detection of the state of the logic inputs with forward operation always having priority over
reverse

Altivar 11 control terminals LI1 : forward

15 V LI1 LIx LIx : reverse

Wiring diagram for 2-wire control

Assignment of logic inputs with

Pocket PC PowerSuite b 3-wire control
Used to control the operating direction and stopping by means of pulsed contacts.
Run (forward or reverse) and stop are controlled by 2 different logic inputs.
Enabled by means of 2 or 3 logic inputs (non-reversing or reversing).
This function is suitable for all non-reversing and reversing applications.

f (Hz)

0 t

Stop 1

0 t

Forward 1

0 t

Reverse 1
0 t

Example of operation with 3-wire control

Altivar 11 control terminals LI1 : Stop

LI2 : Forward
15 V LI1 LI2 LIx
LIx : Reverse

Wiring diagram for 3-wire control

b Automatic d.c. injection

Enables d.c. injection to standstill, which is adjustable from 0 to 1.2 times the value of the drive
nominal current (preset at 0.7 In), as soon as operation is no longer controlled and the motor
speed is zero,
v either for a period of time, which is adjustable from 0.1 to 30 s (preset at 0.5 s)
v or continuously.
Factory setting : function active with d.c. injection for 0.5 s.
In 3-wire control, d.c. injection is only active if logic input LI1 is active (stop).

b Switching frequency, noise reduction

High frequency switching of the intermediate d.c. voltage can be used to supply the motor with
a current wave with low harmonic distortion.
There are 3 ranges of switching frequency :
v Random switching frequency around 2 or 4 kHz (avoids resonance)
v Fixed low frequency adjustable to 2 or 4 kHz
v Fixed high frequency adjustable to 8, 12 or 16 kHz
Factory setting : Low frequency set at 4 kHz.
This function is suitable for all applications which require low motor noise.
Adjustment of the "d.c. injection" function using the
PowerSuite software workshop for PC b Fault relay, unlocking
The fault relay is energised when the drive is powered up and is not faulty.
It opens in the event of a fault or when the drive is powered down.
The drive can be unlocked after a fault in one of the following ways :
v powering down the drive until the display disappears completely, then powering back up
v activating the logic input associated with the fault reset function, if the function is enabled
v enabling the automatic restart function.

Schneider Electric 60255-en_Ver1.1.fm/5

 Functions (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

b Fault reset
Used to clear the stored fault and restart the drive if the cause of the fault has disappeared.
The fault is cleared by a transition of the logic input LI which is assigned to this function.
Factory setting : function inactive.
The restart conditions after a reset to zero are the same as those of a normal power-up.
The following faults can be reset : drive thermal overload, motor thermal overload, line supply
overvoltage, overvoltage on deceleration, overspeed, line phase loss (1), line supply
undervoltage (2).

b Automatic restart
Enables the drive to be restarted automatically after locking following a fault if this fault has
disappeared and if the other operating conditions permit a restart.
This restart is performed by a series of automatic attempts separated by increasingly longer
waiting periods: 1 s, 5 s, 10 s, then 1 minute for the following periods.
If the drive has not restarted after 6 minutes, the drive locks and the procedure is abandoned
until the drive is powered down and back up again.
Factory setting : function inactive.

Restart authorised with the following faults : drive thermal overload, motor thermal overload, line
supply overvoltage, overvoltage on deceleration, line phase loss (1), line supply undervoltage
(2).
If the function is enabled, the drives safety relay remains activated until one of these faults
appears. This function requires the speed reference and the direction of operation to be
maintained, and is only compatible with 2-wire level control.
This function is suitable for machines or installations in continuous operation or without
monitoring, and where a restart will not endanger equipment or personnel in any way.

b Automatic catching a spinning load with speed detection ("catch on the fly")
Used to restart the motor smoothly after one of the following events:
v loss of line supply or power down
v fault reset or automatic restart
v freewheel stop triggered by a fault.
On restarting, the effective speed of the motor is detected in order to restart on the ramp at this
speed and return to the reference speed. The speed detection time can be up to 1 s depending
on the initial deviation.
Factory setting : function inactive.

This function requires the activation of 2-wire level control and is not compatible with the
continuous d.c. injection function.
This function is suitable for machines for which the loss of motor speed is negligible during the
line supply loss time (machines with high inertia).

b Controlled stop on loss of line supply

Used to define the drive stopping modes at a "loss of line supply" fault.
Three stopping modes are available for selection :
v Freewheel stop : the drive is locked and the motor stops in accordance with the inertia and
Adjustment of the behaviour at a the resistive torque
fault with Pocket PC PowerSuite v Normal stop : stop with valid deceleration ramp time (deceleration 1 or 2).
v Fast stop : the stopping time depends on the inertia and the braking ability of the drive.

Factory setting : Freewheel stop.

f (Hz)

1 Fast stop
2 Normal stop on deceleration ramp
3 Freewheel stop

1 2 3
t

b Thermal protection of drive

Direct protection by thermistor, integrated in the drives power module. This protects the
components, even in the event of poor ventilation or excessive ambient temperature.
When the fault is detected, it locks the drive.

b Motor thermal protection

Motor thermal protection is implemented via continuous calculation of its theoretical temperature
rise.
The drive is locked on a fault if this temperature rise exceeds 118% of the nominal temperature
rise.
This function is suitable for applications with self-cooled or force-cooled motors.
Note: The thermal state of the motor is not stored when the drive is powered down.
Adjusting the thermal protection with the PowerSuite
software workshop for PC (1) The line supply phase loss fault is only accessible on drives with 3-phase power supply, if
monitoring of the fault has been enabled (Factory setting : enabled).
(2) The drive will restart as soon as the undervoltage fault disappears, whether or not the function
is active.

60255-en_Ver1.1.fm/6 Schneider Electric

Functions (continued) Variable speed drives
for asynchronous motors 0

Altivar 11

b Monitoring
The display shows the state of the drive or, if selected, one of the following values :
v Frequency reference
v Output frequency applied to the motor
v Motor current
v Line voltage
v Motor thermal state
v Drive thermal state

Incompatible functions
The choice of the last function configured is enabled, whatever the configuration of the previous
functions.
Application functions can be assigned to the same logic input, in which case one logic input
enables a number of functions (for example : direction of operation and 2nd ramp).

A check must be carried out to ensure that the functions are compatible.

b Direction of operation and 2-wire control : forward operation can only be assigned to LI1.
b Direction of operation and 3-wire control : forward operation can only be assigned to LI2.
b Automatic restart : requires the configuration of 2-wire level control. Changing the
configuration of the type of control disables automatic restart.
b Automatic catching a spinning load with speed detection :
v requires the configuration of 2-wire level control. Changing the configuration of the type of
control disables automatic catching a spinning load.
v not compatible with continuous d.c. injection braking to a standstill. Configuring this function
disables automatic catching a spinning load.

Functions specific to the Asia range

b Local control :
The keypad on the Asia range has 2 additional keys (RUN and STOP) and a potentiometer
(speed reference).
v The keys and the potentiometer are active if local control is enabled.
The logic and analog inputs are inactive if local control is enabled.
Factory setting : function active.
v Reverse : if local control is active, the reverse function is not visible.
b Logic inputs :
It is possible to choose the active level of the logic input.
Positive logic : the inputs are active if the signal is 11 V.
Negative logic : the inputs are active if the signal is 5 V.
Factory setting : positive logic.

Schneider Electric 60255-en_Ver1.1.fm/7

mep ATV 11 flash corAng 10/07/02 13:23 Page 3

Telemecanique
Altivar 11
Real efficiency
at a reduced size!...

Altivar 11 variable speed drives for asynchronous motors

from 0.18 to 2.2 kW

Building a New Electric World

mep ATV 11 flash corAng 10/07/02 13:23 Page 4

Altivar 11 :
The little one with
big prospects...

The new Altivar 11 variable speed

drive is truly different, not only in size,
but above all in its features:

Identical performance to the Greats.

Uninterrupted service.
Perfect suitability for any application.
International coverage.

The smallest drive in the world For motor powers

from 0.18 to 2.2 kW

Voltage ranges:
120 V single-phase.
240 V single-phase.
230 V 3-phase.

Standards and certifications:

EN 50178 / EN 61800-3.
EN 55011, EN 55022
class B and class A gr. 1
NOM 117 / C-TICK.
N998
mep ATV 11 flash corAng 10/07/02 13:23 Page 1

...for all
your applications
from 0.18 to 2.2 kW
Thanks to the the advanced flux vector
control and specific application
functions of the Altivar 11:

Parking barriers
Exceptional dynamics:
Use of an advanced flux vector motor control
minimises cycle times.
Customisation of "Up / Down" cycles due to the
assignment of several functions on the same logic input:
Different ramps for up / down cycles.
Up priority if obstructed going down.
Different pre-selectable speeds both for up / down
cycles.
Answers to abrupt weather changes:
Perfect for simple mechanical Operation assured down to -10C.
applications in industrial and
commercial sectors:
Hoardings
Serial configurations and simplified maintenance:
Mechanical handling: Use of PowerSuite software workshop
conveyors, garage doors, parking on standard PC or Pocket PC.
barriers, supplying conveyors, etc... Optimisation of size
Use of baseplate version.
Special machines: Solutions for power supply line noise:
grinders, saws, drills, exercise Built-in EMC class B filters.
equipment, hoardings, Reduction in generated pollution:
extractors, dough mixers, etc... Switching frequency of 16 kHz.
The performance and simplicity
of the Altivar 11 will make you Dough mixers
forget multispeed motors, Perfect control of this motor drive application:
mechanical drives, DC drives, Without tripping as the dough hardens.
special motors and electro- Protection of personnel:
mechanical starters, etc. Due to the low leakage current of the Altivar 11,
It easily replaces all these solutions. the drive can be associated with a 30 mA differential
circuit-breaker. This also includes models with a
built-in EMC class B filter.

Conveyors
Tailored ergonomics, as near to the operator
as possible:
Simple setting-up using local controls:
start / stop buttons and potentiometer for
setting speed available on the drive.
mep ATV 11 flash corAng 10/07/02 13:23 Page 5

Identical performance
to the Greats
Total control of your machines:

Optimal management of the motor due to flux vector

control: 150% of the nominal current of the drive during
60 seconds with a 1:20 speed ratio.

Ability to catch a spinning load after a supply break

or on a start command for smooth take-up of a
rotating machine.

Dynamic braking possible, even for high inertia and

unbalanced load applications.

Uninterrupted
service
High degree of monitoring and protection at all levels:

Of the motor
thermal protection by continuous calculation of I2t.
Robustness
to meet every Of the drive
challenge thermal protection by PTC probe integrated in the
Even in severe power module,
environments from protection against short-circuits between output
-10 up to +50 C, phases.
the Altivar 11 is safety related to the supply line:
perfectly - overvoltage,
operational - undervoltage,
without any - phase failure (on 3-phase)
degradation in its
performance. Of personnel
Due to the low leakage current of the Altivar 11,
the drive can be associated with a 30 mA differential
circuit-breaker. This also includes models with a
built-in EMC class B filter.
mep ATV 11 flash corAng 10/07/02 13:24 Page 6

Perfect suitability
The smallest drive for any application
in the world !
The compactness of the Altivar 11 considerably
reduces the size of your enclosures and, in
addition, reduces the size yet again due to the
possibility of mounting several drives side by side.

Through wiring and connection using captive

screws simplify installation and replacement of
electromechanical solutions.

DIN rail mounting option also contributes to additional

savings in installation time.

Multi-assignment of logic inputs (several functions on

Example of assigning the same input) increases tenfold its application
operating functions to capabilities.
a single logic input

The closest
possible to
machines...
International coverage
The Altivar 11 could
not be closer to
your machine:
it can be installed
directly on its
framework (version Built-in
on baseplate). EMC
class B Local
The use of natural Current NEC filter controls
convection up to 208 V 1999 (Europe). and
0.75 kW makes (North negative
them ideal where America). logic.
silent operation is
necessary.
(Asia).

The Altivar 11 has its place anywhere in the world:

its ranges are suitable for the technical requirements
and standards of all the markets.
mep ATV 11 flash corAng 10/07/02 13:24 Page 7

With total simplicity

and user-friendliness
Wire it, connect it, start
Factory set, the Altivar 11 is
operational immediately.

Customise your settings with the minimum of effort

The built-in display guides you through

the main parameters for fast configuration.

Does your application require particular settings?

3 simple and intuitive menus allow you to:
adjust the parameters of your motor application,
configure the specific functions of your machine,
select the value indicated on the display of the drive.

For improved security, your settings can be automatically

saved on the Altivar 11 and subsequently recalled.

Protect
everything in
memory with
PowerSuite* software

In addition to its user-friendliness

and ergonomics for adjusting
and storing your parameters,
PowerSuite allows
the back-up
of each
configuration.
This, in turn,
can be quickly
recalled and
used for similar
applications
without the risk of
error.

* Software which is common to the Altivar range of variable speed drives.

Available in 5 languages (English, French, German, Italian, Spanish).
mep ATV 11 flash corAng 10/07/02 13:24 Page 8

Altivar 11 selection guide

Variable speed drives with heatsink - 50 / 60 Hz

Dimensions (in mm)

Europe Motor Permanent Reference
power output ATV11... w h d **
range current
Built-in EMC HU05 M2/ M3 / F1 72 142 101
class B filter. kW A single-phase
HU09 M2 / M3 / F1 72 142 125
Supply voltage : 200 to 240 V
HU12 M2 72 142 138
0.18 1.1 ATV 11HU05M2E
HU18 M2 / M3 72 142 138
0.37 2.1 ATV 11HU09M2E *
HU18 F1 117 142 156
0.55 3 ATV 11HU12M2E *
HU29 M2 / M3 117 142 156
0.75 3.6 ATV 11HU18M2E *
HU41 M2 / M3 117 142 156
1.5 6.8 ATV 11HU29M2E
On baseplate
2.2 9.6 ATV 11HU41M2E
PU M2 / M3 / F1 72 142 101
w : width / h : height / d : depth

America Motor Permanent Reference

range. power output
Permanent current
output current kW HP A Single-phase 3-phase
conforming to
Supply voltage : 100 to 120 V
the standard
NEC 208 V 1999. 0.18 0.25 1.6 ATV 11HU05F1U -
External EMC 0.37 0.5 2.4 ATV 11HU09F1U* -
class B filter 0.75 1 4.6 ATV 11HU18F1U -
as option.
Supply voltage : 200 to 240 V 200 to 230 V
0.18 0.25 1.6 ATV 11HU05M2U ATV 11HU05M3U
0.37 0.5 2.4 ATV 11HU09M2U * ATV 11HU09M3U *
0,75 1 4.6 ATV 11HU18M2U * ATV 11HU18M3U *
1.5 2 7.5 ATV 11HU29M2U ATV 11HU29M3U
2.2 3 10.6 ATV 11HU41M2U ATV 11HU41M3U

Motor Permanent Reference

Asia power output
range. current
Local controls kW A Single-phase 3-phase
on the drive and Supply voltage : 100 to 120 V
negative logic.
External EMC 0.18 1.4 ATV 11HU05F1A -
class B filter 0.37 2.4 ATV 11HU09F1A * -
as option. 0.75 4 ATV 11HU18F1A -
Supply voltage : 200 to 240 V 200 to 230 V
0.18 1.4 ATV 11HU05M2A ATV 11HU05M3A
0.37 2.4 ATV 11HU09M2A * ATV 11HU09M3A *
0.75 4 ATV 11HU18M2A * ATV 11HU18M3A *
1.5 7.5 ATV 11HU29M2A ATV 11HU29M3A
2.2 10 ATV 11HU41M2A ATV 11HU41M3A

* Replace the letter " H " by " P " to obtain the reference of the version on a baseplate.
** Add 7 mm to the depth for the Asia range.
mep ATV 11 flash corAng 10/07/02 13:23 Page 2

A comprehensive range
of Motor Starters
Increase your performance with
Variable speed drives the associated TeSys components*

Circuit-breakers,

Differential
circuit-breakers,
Altivar 11 Altivar 38
0.18 to 2.2 kW 0.75 to 315 kW

Contactors.

Altivar 28
0.37 to 15 kW

*For further details on product combinations,

please refer to our catalogue.

Altivar 58 Altivar 68
0.37 to 75 kW 75 to 630 kW
A unique partner,
a global presence

Soft start - soft stop units Constantly available, worldwide.

With more than 5000 points of sale in 130 countries, you can
be sure to find the range of products which is right for you
and which complies totally with the standards in the country
in which they are to be used.

Schneider Electric Services

Our services, near you, wherever you are.
Our experts are at your disposal, working with you to design
your customised solution.
Our aim: to optimise your installations and improve your
LH4 Altistart 48
industrial performance.
6 to 85 A 17 to 1200 A

Schneider Electric Industries S.A.S.

Head office
89 boulevard Franklin Roosevelt
92504 Rueil Malmaison Cedex Owing to changes in standards and equipment, the characteristics given in the text
VVDED102051EN

FRANCE and images in this document are not binding until they have been confirmed with us.
http://www.schneider-electric.fr Production: 3000 NR
Photos: Schneider Electric - ImageBank

038996 06/2002