Valvulas Cedaspe

THROTTLE VALVES FOR RELAYS AND RADIATORS
Series 2009
1General Features
1.1Characteristics
The butterfly valves, metal to metal sealing withy thin blade(or full tightening type, with o-ring blade), are
used on power transformer with the scope to allow disconnection of a component of the circuit (ie
buchholz relay or radiator) without having to lower the oil below the level of the component itself.
This kind of valve are preferred to the conventional gate valves for their compact overall dimension in the
direction of the oil flow.
1.2Field of Use
The butterfly valves (standard execution) may be used with the following characteristic values:
Fluid: mineral oil
operating pressure max 10 bar
working temperature from 20C to + 110C
2Construction Features, Finish and Accessories

2.1Construction Features
Butterfly valves are constructed as follows (please refer to drawings):
Body made in forged mild steel
Spindle made in steel
Drive and gland made in brass
Open/close position indicated by a n aluminium plate.
S/steel screws
Throttle made in carbon steel (thin blade) or made in brass (o-ring blade)
O/Rings made in oil resistant rubber
2.2Finish
Body of wafer type is zinc plated first and after is protected by one coat of epoxy primer and one coat of
polyurethane paint (total thickness 80 m), final colour RAL 7030; in all types screws and pins are in
stainless steel; brass parts and aluminium parts are self colour.
In any case the device is suitable for outdoor installation in tropical climate and with normal industrial
pollution.
Body of welding neck type is self colour without any coating or painting
2.3Accessories
The valve is supplied with one (or two) O/Ring flange gasket
2.4Special executions
Special execution are available for very low temperatures or very corrosive ambient. Please contact our
technical department.
File : 24-BUTTERFLY VALVES.doc rev. 04 dtd 15/09/2008 UNCONTROLLED COPY Page 1 di 4

3Operating features
3.1Tightness of spindle
The tightness to oil leakage from the spindle on the butterfly valve, is guaranteed by a set of o/rings on
the spindle and on the gland obtaining an excellent tightness and at the same time allowing an easy
replacement of the gasket
No leakage is tolerated from the spindle in any case.
3.2Tightness of butterfly
3.2.1Metal to metal sealing (thin blade throttle)
The oil tightness of the butterfly is obtained by contact metal to metal, thus assuring a constant
performance even after a long use .
Leakage at the butterfly is checked during assembly, testing with oil at 20 C, 1 bar and viscosity of
30,5 cSt.
Following values of max admitted leakage:
Nominal diameter of valve in mm 100 100 < > 175 175

Admitted leakage in dm /h measured in 1 hour 0,5
3
1,0 2,0
3.2.2Full tightening sealing (TW80 with o-ring blade)

The oil tightness of the butterfly is obtained by contact of an o/ring (mounted on the throttle) and the
metal body, thus assuring full sealing between throttle and body.
No leakage is present between throttle and body in closed position.
3.3Operating Torque
The operating torque measured by dynamometric spanner are the following :
Nominal diameter of valve in mm 100 100 < > 150 150

Operating torque in Nm. 10 30 30
Closing torque in Nm. 70 100 150
Opening torque in Nm. 40 50 50
Operating torque: Torque necessary to turn the shaft from the open to the closed position;
Closing torque: Torque necessary to obtain the complete closure of the valve;
Opening torque: Torque necessary to open the valve, after complete closure.

4Admitted operating conditions
4.1Standard execution (N) Nitrile rubber gaskets
Ambient conditions:
Ambient temperature: -20C to +50C
Relative humidity: 95% to 20C - 80% to 40C - 50% to 50C
Insulating liquid and it's temperature:
Mineral oil: -20C to +110C
Silicone oil: -20C to +110C
4.2Execution H H-NBR rubber gaskets
Ambient conditions:
Silicone oil: not admitted
4.3Execution V Fluor-rubber gaskets (Viton V)
Ambient conditions:
Silicone oil: -15C to +160C
5Mounting, Adjustment and Maintenance

5.1Mounting
The throttle valve has to be mounted on pipe as shown on reference drawings or at page 5.86
Valve has to be mounted using screws or rods, washers and nuts and putting the o/ring on the
groove for flange tightening
5.2Operating instructions
The design of the operating system is common to all valves; to open and close the valve operate as
follows (please refer to drawings):
The visible symbol or inscription on plate (10) indicates the valve position;
To close the valve first remove the seal or padlock (if present),
With the appropriate spanner turn the drive (2) clockwise 90 to close the valve; counter clockwise
90
to open the valve
The visible part of plate (10) indicates the new valve position;
5.3Maintenance
The Throttle valves do not need periodic maintenance; however it is advisable to check regularly the
external tightening of valve

6Range of types and reference drawings
The butterfly valves have standard execution flanges according to UNI PN10 and PN6; flanges according
to other standards can be supplied as special execution.
Nominal diameters (DN) are 25;50;80;100;125;150;200;250;300
Below detailed list of available types
6.1Series SW for radiators metal to metal sealing (square flange thin blade)
Nominal diameter: 80 mm
Execution
- A1 Welding neck
- B1 Wafer type for mounting between two flanges
Reference drawing : page 5.82
Mounting sketch
- A1 Welding neck : page 5.86 fig. A or B
- B1 Wafer type for mounting between two flanges : page 5.86 fig. C or D
6.2Series TW for radiators full tightening valve (square flange o/ring blade)
Nominal diameter: 80 mm
- Execution wafer type for mounting between two flanges
- Mounting sketch: page 5.86 fig. C or D
6.3Series DN round flange
Nominal diameter: 25; 50; 80 mm
Execution wafer type for mounting between two flanges
- PN6 max operating pressure 6 bar bolt circle diameter acc to UNI2276-67
Note : this kind of valves are equipped with HNBR gaskets
6.4Series JU large round flange
Nominal diameter: 100;125;150;200;250;300 mm
Execution wafer type for mounting between two flanges
7Order Specifications
When ordering it is necessary to indicate
Series (type)
Size
Operating conditions (if not indicated, we will consider standard N)
Special requirements
Example :
To order nr. 1 Throttle valve type DN50 PN6 standard execution please indicate the following:
Nr 1 Throttle valve DN50 PN6

Valvulas Cedaspe

Uploaded by

Copyright:

Available Formats

Valvulas Cedaspe

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Valvulas Cedaspe

Uploaded by

Copyright:

Available Formats

THROTTLE VALVES FOR RELAYS AND RADIATORS

2Construction Features, Finish and Accessories

File : 24-BUTTERFLY VALVES.doc rev. 04 dtd 15/09/2008 UNCONTROLLED COPY Page 1 di 4

Nominal diameter of valve in mm 100 100 < > 175 175

3.2.2Full tightening sealing (TW80 with o-ring blade)

Nominal diameter of valve in mm 100 100 < > 150 150

File : 24-BUTTERFLY VALVES.doc rev. 04 dtd 15/09/2008 UNCONTROLLED COPY Page 2 di 4

5Mounting, Adjustment and Maintenance

File : 24-BUTTERFLY VALVES.doc rev. 04 dtd 15/09/2008 UNCONTROLLED COPY Page 3 di 4

File : 24-BUTTERFLY VALVES.doc rev. 04 dtd 15/09/2008 UNCONTROLLED COPY Page 4 di 4

You might also like