Service Training

Self-study programme 330

The diesel particulate filter system

with additive

Design and Function

 Combustion will remain in the foreseeable future an These aspects and strict emissions legislation have led
important method of energy conversion, whether in engineers to place particular emphasis on the conti-
power stations, cars or even fireplaces. nual reduction of particulate emissions.

Every fire leaves behind harmful by-products of One way to reduce the emission of carbon soot is with
combustion - particles of soot for example. a diesel particulate filter.

The aim is to avoid risks to the environment and health

caused by the generation and release of carbon soot.

S330_001

Further information on the subject of exhaust gas can be found in the following self-study programmes:

SSP 124: Diesel engine with catalytic converter

SSP 230: Vehicle exhaust emissions
SSP 315: European onboard diagnosis for diesel engines

NEW Caution
Note

The self-study programme represents the design For current testing, adjustment and repair instruc-
and function of new developments! tions, refer to the relevant service literature.
The contents will not be updated.

2
Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Design and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

System overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Sensors and actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

System limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Test yourself. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3
 Introduction

General
During combustion of diesel fuel, all sorts of different In addition to harmful gaseous substances, particles
deposits are built up. Those that can be perceived of solid substances are emitted with the emissions
directly as emissions components on a cold engine from diesel engines, which have been included under
are non or partly oxidised hydrocarbons in droplet the main heading of particulates with regards to
form as white or blue smoke and strong smelling substances that are damaging to health and the
aldehyde. environment.

S330_035

Volkswagen follows a long-term strategy with the aim Volkswagen played an important role in driving on
of reducing exhaust emissions not only in the area the development for clean diesel fuel and thereby
of diesel particulates but also for all other emissions faced the responsibility of protecting the environment.
components, such as hydrocarbons and nitrogen Examples of this are the efficient, economical and low
oxides. Some years ago, Volkswagen undertook tough noise generating TDI technology and also the unit
measures on a continual basis to optimise the internal injector system. Volkswagen will continue to selectively
combustion processes and to reduce the emission of improve internal combustion processes in the future to
carbon soot particles from diesel engines. And with further bring down fuel consumption and reduce
success: In 1999, Volkswagen was able to offer the emissions directly at source. In addition, Volkswagen
Lupo 3L TDI on the market as the first vehicle to meet will enhance these efforts step-by-step by the
the strict Euro 4 exhaust emissions standard six introduction of diesel particulate filter systems.
years before the standard was established as a legal
requirement in 2005.

4
The exhaust gas
Emissions standards
In the Republic of Germany, across Europe and throughout the world, laws have been passed in recent years to
reduce the emission of harmful substances in the air. In Europe, the emissions standards are categorised from EU1
to EU4. These prescribe emission limits to the automobile industry for type approval of new vehicle models.

EU3 EU4

As of the year 2000, EU3 is the emissions standard The EU4 standard will come into force in 2005 and
for new vehicle registrations. will supersede EU3. The consequences are a further
reduction in permissible limit values.
It differs from its predecessor EU2 by more stringent
conditions on the test bed and by a reduction in the Even now, more than 65 percent of all Volkswagens
limit values. with diesel engines newly registered in Germany fulfil
emissions standard EU4.

Permissible limit values for diesel engines

g/km
0,8
0,64
0,56
0,6
0,50 0,50

0,4
0,30
0,25

0,2
0,05 0,025

EU3 EU4 EU3 EU4 EU3 EU4 EU3 EU4

CO HC + NOX NOX PM S330_026
Carbon monoxide Hydrocarbons and Nitrogen oxides Soot particles
nitrogen oxides

Outlook

In the future, the more stringent EU5 standard will come into force. The limit values for this standard have as yet not
been established, but acceptable emission levels will be lowered even further. There are plans to markedly reduce
the particulate limit value for diesel passenger vehicles even further. Therefore, all diesel passenger vehicles must
be fitted with a particulate filter in the future.

5
 Introduction

Harmful substances caused by combustion

The harmful substances, and particulate emissions in particular, are influenced in a diesel engine by the
combustion process. This process is affected by many factors relating to the construction, the fuel itself and the
atmosphere.
The following illustration shows an overview of the inlet and exhaust components of a diesel engine during
combustion.

Injected fuel:
HC Hydrocarbons
S Sulphur

approx. 12%

SO2
CO2 approx.
11% PM
N2 H2O
approx. HC
O2 0,3%
NOX
approx.
10% CO
Intake air:
approx. 67%
O2 Oxygen
N2 Nitrogen S330_108
H2OWater
Exhaust gas:
(humidity)
O2 Oxygen CO Carbon monoxide
N2 Nitrogen HC Hydrocarbons
H2O Water SO2 Sulphur dioxide
CO2 Carbon dioxide NOx Nitrogen oxide
PM Carbon soot particles
(PM = particulate matter)

With regards to the damaging effect on the Carbon dioxide, which is present in the atmosphere as
environment and health, the emissions from a diesel a natural gas, is at the limit between safe and harmful
engine have various components that require due to its categorisation. It may not be poisonous, but
different analyses. in higher concentrations it can contribute towards the
Those components that are already present in the greenhouse effect.
atmosphere (oxygen, nitrogen and water) can be Carbon monoxide, hydrocarbons, sulphur dioxide,
categorised as safe. nitrogen oxide and particulates are categorised as
harmful.

6
Harmful substances in the exhaust gas
Carbon monoxide (CO) is generated from oxygen
deficiency as a result of the incomplete combustion of
CO
Carbon fuels containing carbon. It is a gas and has no colour,
monoxide smell or taste.

S330_014

Hydrocarbons cover a wide range of different

HC compounds (for example C6H6, C8H18), which occur
Hydrocarbons as a result of incomplete combustion.

S330_016

Sulphur dioxide is generated by the combustion of

SO2 fuel containing sulphur. It is a gas without colour but
Sulphur dioxide with a pungent smell. The amount of sulphur added to
fuel is decreasing.

S330_018

Nitrogen oxides (for example NO, NO2, . . .)

NOx are generated by high pressure, high temperature
Nitrogen oxides and excessive oxygen during combustion in the
engine.

S330_020

If there is an oxygen deficiency the result is a build up

Soot particles
of carbon soot particles from incomplete combustion.

S330_022

7
 Introduction

The particulates
Particulates is a term that covers all particles, solid or Particulates have the same character as harmful
liquid, that are generated from friction, breakdown of substances in the air if, due to their small dimensions,
components, erosion, condensation and incomplete they can float around in gaseous substances and
combustion. These processes create particulates in damage organisms.
different shapes, sizes and structures.

Soot particles
Soot particles are generated from the combustion Some hydrocarbon compounds are categorised as
process in a diesel engine. Soot particles are potentially hazardous to health.
microscopic balls of carbon with a diameter of about The exact composition of soot particles depends on
0.05 m. Their core consists of pure carbon. the engine technology, the conditions of use and the
Around the core are deposits of different type of fuel.
hydrocarbon compounds, metal oxides and sulphur.

SO4 (sulphate)
Hydrocarbons

Carbon Sulphur and metal oxides

H2O (water)

S330_182

8
Cause of soot particles
The build up of soot particles in a diesel engine depends on the individual processes of diesel combustion, such as
air intake, injection, flame spread.
The combustion quality depends on how well the fuel is mixed with the air.
The mixture in some areas of the combustion chamber could be too rich because not enough oxygen is present.
Combustion will then be incomplete and soot particles will be formed.

The mass and number of particles are therefore

affected in essence by the quality of the engine
combustion process. With high injection pressure and
an injection pattern based on the requirements of the
engine, the unit injector system ensures efficient
combustion and thereby reduces the formation of soot
particles during the combustion process.
High injection pressure and associated fine
atomisation of the fuel, however, does not necessarily
lead to smaller particles.
Tests have shown that the difference in particle sizes in
the exhaust gas is very similar regardless of the
combustion principle of the engine, whether swirl
S330_013
chamber, common rail or unit injector technology.
Typical particle of soot caused from diesel
engine combustion

9
 Introduction

The measures to reduce particulates

The reduction of exhaust emissions in a diesel engine is an important aim in further development.
To reduce exhaust emissions there is a series of different technical solutions.
Here, a difference is made between internal and external engine measures.

Internal engine measures

A reduction in emissions can be achieved by Effective optimisation of the combustion process can
measures to the internal workings of an engine. ensure that harmful substances are not produced
at all.

Examples of internal engine measures are:

the design of the inlet and exhaust ports for

optimal flow properties,

high injection pressures by means of unit injector

technology,

the combustion chamber design, for example

reduction in the size of the area where harmful
substances are produced, design of the piston
crown.

S330_045

10
External engine measures
The release of soot particles that are produced during combustion can be prevented by external engine measures.
This can be seen as the reduction of soot particles by means of a particulate filter system.
To do this, it is necessary to differentiate between two systems the diesel particulate filter with additive and the
diesel particulate filter without additive. Explained on the following pages is exclusively the design and function of
the diesel particulate filter systems with additive, currently used by Volkswagen.

System with additive

This system is used on vehicles where the particulate filter is installed away from the engine. Due to the distance the
exhaust gas has to make from the engine to the particulate filter, the required ignition temperature for combustion
of the particulates can only be reached with the introduction of an additive.

Temperature of exhaust gas in this

area at part-throttle

750C

Oxidising catalytic con-

verter Particulate filter

620C 500C S330_142

System without additive

This system will be installed in the future on vehicles with particulate filters close to the engine. Due to the short
distance exhaust gas has to take from the engine to the particulate filter, the temperature of the exhaust gas is
sufficiently high enough to burn off the carbon soot particles.

Temperature of exhaust gas in this

area at part-throttle

750C
Particulate filter with integrated
oxidising catalytic converter

620C S330_144

11
 Design and function

The diesel particulate filter system with additive

Shown in the overview below are the components of the diesel particulate filter system. The design and function of
the diesel particulate filter system with additive are explained on the following pages.

6 3

2
5

7 4
16

14
8
9
11 13
10 15
12

S330_030

1 Control unit in dash panel insert J285 9 Turbocharger

2 Engine control unit 10 Lambda probe G39
3 Additive tank 11 Oxidising catalytic converter
4 Fuel additive tank empty sender G504 12 Temperature sender before particulate filter G506
5 Particulate filter additive pump V135 13 Particulate filter
6 Fuel tank 14 Exhaust gas pressure sensor 1 G450
7 Diesel engine 15 Silencer
8 Temperature sender before turbocharger G507 16 Air mass meter

The overview shows a system with single exhaust pipe. In the event of twin or multi exhaust systems
(for example on the V10 TDI engine), the particulate filter and exhaust gas sensors are fitted to each
line of the exhaust system.

12
The particulate filter
The diesel particulate filter (for example on the Passat
with 2.0 ltr. TDI engine) can be found in the exhaust
pipe after the oxidising catalytic converter.

It filters particles of carbon out of the

exhaust gas of the engine.

S330_017

Design
The diesel particulate filter comprises of a honeycomb Silicon carbide is a suitable filtering
ceramic matrix made from silicon carbide, which can material due to the following properties:
be found in a metal housing. The ceramic matrix itself
has many microscopic channels that run parallel and High mechanical strength
are alternately connected to each other. Very good resistance to thermal changes
Thermal resilience and conductivity
High resistance to wear

Honeycomb
ceramic matrix

S330_038

S330_154

Function
When exhaust gas enters the filter, particles of carbon are trapped in the input channels, while the gaseous content
of the exhaust gas flows through the porous walls of the ceramic filter.

13
 Design and function

Regeneration
The diesel particulate filter must be cleaned of the In order to ensure regeneration of the diesel particu-
particles of regularly to prevent it from becoming late filter under all operating conditions, the ignition
blokked and its function thereby being affected. temperature of the carbon is lowered by the
During the regeneration phase, the particles of introduction of an additive, and the exhaust gas
carbon stored in the filter are burnt off at a temperature is raised by the engine management
temperature of approx. 500C. The actual ignition system.
temperature of the particulates is about 600-650C.
This exhaust gas temperature can only be reached on The regeneration procedure is initiated by the engine
a diesel engine at full throttle. control unit.

Particulate filter empty

Signals to
engine control unit

Air mass meter G70

Exhaust gas pressure sensor 1

G450
Temperature sender
before particulate filter G506

S330_042

Particulate filter empty = low resistance to flow

Particulate filter full

Signals to
engine control unit
Air mass meter G70

Exhaust gas pressure sensor 1

Temperature sender G450
before particulate filter G506

S330_044

Particulate filter full = high resistance to flow

14
During regeneration, the tiny particles of carbon
stored in the particulate filter are burnt off.
This occurs every 500-700 kilometres, depending on
the way the vehicle is driven, and lasts about 5-10
minutes. There are no signs to the driver that
regeneration is occurring.

Regeneration of the particulate filter

Signals to
engine control unit

Air mass meter G70

Exhaust gas pressure sensor 1

G450
Temperature sender before
particulate filter G506

S330_051

15
 Design and function

The additive
The additive is an iron-rich substance, which is
dissolved in a hydrocarbon mixture.
It can be found on the Passat in a separate fuel tank
in the spare wheel well.

Additive tank S330_112

The additive has the task of lowering the temperature The additive is mixed automatically with the fuel in the
at which the carbon particles burn, in order to allow tank via the fuel return line each time the fuel tank is
regeneration of the particulate filter even at replenished. This occurs by means of a particulate
part-throttle. filter additive pump, which is actuated
by the engine control unit.
The ignition temperature of the particulates The amount of fuel replenished is determined by the
is about 600-650C. Exhaust gas temperatures at this engine control unit, which draws information from the
level are only achieved on diesel engines at full fuel tank sender. Each time additive is added to the
throttle. By introducing the additive, the ignition fuel tank, the concentration of iron molecules in
temperature of the carbon particles is reduced to the fuel is 10 ppm (parts per million).
approx. 500C. This equates to an approximate ratio of 1 litre
of additive to 2800 litres of fuel.

Additive Carbon particles

The additive in the fuel finds its way into the

particulate filter together with the carbon soot. It
builds up here as a deposit between the particles of
soot.

S330_186

16
Level of carbon deposit in particulate filter
The level of carbon deposit in the particulate filter is constantly monitored by the engine control unit, which
calculates the flow resistance of the filter. To determine the flow resistance, the exhaust gas volume before the
particulate filter is compared with the pressure difference before and after the particulate filter and recorded as a
ratio.

Pressure difference
The pressure difference of the air flow before and after the particulate filter is calculated by exhaust gas pressure
sensor 1.

Exhaust gas volume

The exhaust gas volume is calculated by the engine control unit from the air mass in the exhaust manifold
and the exhaust gas temperature before the particulate filter. The mass of exhaust gas is roughly equivalent to the
mass of air in the intake manifold, which is calculated by the air mass meter. The volume of exhaust gas depends
on the respective temperature. This is calculated by the temperature sender before particulate filter.
Using the exhaust gas temperature reading, the engine control unit can calculate the exhaust gas volume from the
mass of air in the exhaust gas.

Flow resistance of particulate filter

300
Pressure difference p (mbar)

250

200

150

100

50

0 100 200 300 400 500 600 700 S330_156

3
Volume (m /h)

Diesel particulate filter:

full
empty
defective

The engine control unit creates a ratio from the pressure difference and the volume of exhaust gas and can thus
calculate the flow resistance of the particulate filter. From the flow resistance, the engine control unit can detect the
level of carbon deposit.

17
 Engine management during regeneration
From the flow resistance of the filter, the engine control unit can detect the level of carbon deposit in the filter.
A high flow resistance indicates that the filter is in danger of becoming blocked. The engine control unit initiates
regeneration. To do this:

exhaust gas recirculation is switched off to

raise the combustion temperature,

S330_124

an extended injection period is initiated, after a

period of main injection with reduced quantity at
35 crankshaft angle after TDC, in order to increase
the exhaust gas temperature,

S330_126

the supply of intake air is regulated by an

electric throttle valve and

S330_120

the charge air pressure is adapted so that

the torque during regeneration does not change
noticeably by the driver.

S330_122

18
 System overview

System overview of diesel particulate filter with additive

CAN bus
Control unit in dash panel insert J285

Exhaust gas pressure sensor 1

G450

Diesel particulate filter

warning lamp K231

Preglow control
Temperature sender before
lamp K29
particulate filter G506

Temperature sender before

turbocharger G507
Particulate filter additive pump V135
Diesel direct injection system
control unit J248

Lambda probe G39

Lambda probe heater Z19

Air mass meter G70 Diagnosis connector

Unit injector valves N240-N243

Fuel additive empty sender G504 Solenoid valve block with:

Exhaust gas recirculation valve N18
Charge pressure control solenoid valve N75
S330_106

Fuel gauge sender G

Intake manifold flap motor V157

19
 Sensors and actuators

The sensors
Exhaust gas pressure sensor 1 G450
Exhaust gas pressure sensor 1 uses piezo technology.

Signal application

Exhaust gas pressure sensor 1 measures the pressure

difference in the flow of exhaust gas before and after
the particulate filter. The signal from the exhaust gas
pressure sensor, the signal from the temperature
sender before particulate filter and the signal from
the air mass meter form an inseparable unit during
S330_048
calculation of the level of carbon soot deposit in the
particulate filter.

Effects of signal failure

In the event of signal failure from the exhaust gas After a predetermined number of cycles, the diesel
pressure sensor, the particulate filter regeneration particulate filter warning lamp will light up and then
cycle will be based on the distance travelled or the the preglow control lamp will flash in the dash panel
number of hours of operation. This cycle for insert. This informs the driver that the vehicle must be
particulate filter regeneration, however, is not driven to a workshop.
effective over a long period of time.

Design

Exhaust gas pressure sensor 1 features two pressure

Signal to
connections. Leading from one is a pressure line to the
Membrane with piezo control unit
flow of exhaust gas before particulate filter and from elements
the other to the flow of exhaust gas after particulate
filter.

Installed in the sender is a membrane with piezo

elements, which effect the respective exhaust gas
pressures.
S330_050

Pressure before Pressure after

filter filter

20
This is how it works:

Particulate filter empty

If the particulate filter has a very low carbon soot

deposit level, the pressure before and after the filter is
almost the same.
S330_090
The membrane with the piezo elements is in the rest
position.

Piezo ele-
ments

S330_160

Pressure before filter = pressure after

filter

Particulate filter full

If there is a build up of carbon soot in the particulate

filter, the exhaust gas pressure rises before the filter
due to a lower flow volume.
The exhaust gas pressure behind the filter remains
S330_092
almost the same. The membrane changes its shape
depending on the difference in pressure.
This deformation alters the electrical resistance of the
piezo elements, which are connected to form a test
bridge. The output voltage of this test bridge is
processed, amplified and sent by the sensor
electronics as a signal voltage to the engine control
S330_162
unit. From this signal, the engine control unit
calculates the level of carbon soot deposit in the
Pressure before filter > pressure after
filter particulate filter and initiates regeneration to clean
the filter.

The level of carbon soot deposit in the particulate filter can be checked using vehicle diagnosis,
testing and information system VAS 5051 as a "particulate charge coefficient" in a measured value
block.

21
 Sensors and actuators

Temperature sender before particulate filter G506

S330_100
S330_114

The temperature sender before particulate filter is a It can be found in the exhaust system before the diesel
PTC sensor. On a sensor with PTC (positive particulate filter. There it measures the temperature of
temperature coefficient), resistance rises as the exhaust gas.
temperature increases.

Signal application Effects of signal failure

Using the signal from the temperature sender before In the event of signal failure from the temperature
particulate filter, the engine control unit calculates the sender before particulate filter, the particulate filter
exhaust gas volume in order to determine the level of regeneration cycle will be based on the distance
carbon soot deposit in the particulate filter. travelled or the number of hours of operation.

The signal from the temperature sender before This cycle for particulate filter regeneration, however,
particulate filter, the signal from the air mass meter is not effective over a long period of time. After a
and the signal from the exhaust gas pressure sensor predetermined number of cycles, the diesel
form an inseparable unit during calculation of the particulate filter warning lamp will light up and then
level of carbon soot deposit in the particulate filter. the preglow control lamp will flash in the dash panel
insert. This informs the driver that the vehicle must be
Furthermore, the signal is used as a form of driven to a workshop.
component protection to protect the particulate filter
against high exhaust gas temperatures.

22
Temperature sender before turbocharger G507

S330_096

S330_180

The temperature sender before turbocharger

is a PTC sensor. It can be found in the exhaust system
before the turbocharger. There is measures the
temperature of the exhaust gas.

Signal application Effects of signal failure

The engine control unit requires the signal from the In the event of failure from the temperature sender
temperature sender before turbocharger to calculate before turbocharger, the turbocharger can no longer
start of injection and the quantity of extended be protected against excessively high temperatures.
injection for regeneration. In this way, the required Regeneration of the diesel particulate filter is stopped.
temperature increase for combustion of the carbon By means of the preglow control lamp, the driver is
soot particles is reached. informed that the vehicle should be driven to a
In addition, the signal is used to protect the workshop.
turbocharger against excessively high temperatures To reduce the carbon soot emissions, exhaust gas
during regeneration. recirculation is switched off.

23
 Sensors and actuators

Lambda probe G39

The lambda probe is of the broadband type. It can be
found in the exhaust manifold before the oxidising
catalytic converter.

S330_098

Signal application Effects of signal failure

With the lambda probe, the percentage of oxygen in Regeneration of the particulate filter is not as efficient
the exhaust gas can be determined across a wide but remains functional.
measuring range. In conjunction with the diesel In the event of lambda probe failure, there could be
particulate filter system, the engine control unit uses an increase in nitrogen oxide emissions.
the signal from the lambda probe for precise
calculation of the quantity and start of extended
injection for regeneration. For effective regeneration
of the particulate filter, a minimal percentage of
oxygen in the exhaust gas is required at a continually
high exhaust gas temperature. This regulation is made
possible by the signal from the lambda probe in
conjunction with the signal from the temperature
sender before turbocharger.

Detailed information about the broadband lambda probe can be found in self-study programme SSP
231 "Euro onboard diagnosis for petrol engines".

24
Air mass meter G70
The hot film air mass meter is installed in the intake
manifold. Using the air mass meter, the engine control
unit can determine the actual mass of intake air.

S330_184

Signal application Effects of signal failure

In conjunction with the diesel particulate filter system, In the event of signal failure from the air mass meter,
the signal is used for calculation of the exhaust gas the particulate filter regeneration cycle will be based
volume in order to determine the level of carbon soot on the distance travelled or the number of hours of
deposit in the particulate filter. operation.

The signal from the air mass meter, the signal from the This cycle for particulate filter regeneration, however,
temperature sender before particulate filter and the is not effective over a long period of time. After a
signal from the exhaust gas pressure sensor form an predetermined number of cycles, the diesel particu-
inseparable unit during calculation of the level of late filter warning lamp will light up and then the
carbon soot deposit in the particulate filter. preglow control lamp will flash in the dash panel
insert. This informs the driver that the vehicle must be
driven to a workshop.

25
 Sensors and actuators

Fuel additive tank sender G504

The fuel additive tank sender can be found in the
additive tank.

S330_138 S330_146

Signal application Design

Once the fill level in the additive tank reaches a

Preglow control lamp
minimum point, the preglow control lamp is activated
in the dash panel insert by the fuel additive tank
sender signal. In this way, the driver is informed of a
malfunction in the diesel particulate filter system and Dash panel insert
instructed to seek a workshop.
In the event of the additive quantity being too low,
particulate filter regeneration is also stopped and
engine performance is reduced.

Reed contact

Magnetic ring

Float
S330_128

26
This is how it works:

Installed in the shaft of the fuel additive tank sender is

a reed contact. It is activated by the magnetic ring
Additive installed on the float. If there is sufficient additive in
the tank, the float will be in contact with the upper
stop. The reed contact is open.

Float Reed contact Magnetic ring

S330_136

If there is not enough additive in the tank, the float will

drop to the lower stop. As it does this, the reed contact
will be closed by the magnetic ring. The preglow
Additive control lamp lights up.

Float Reed contact Magnetic ring

S330_134

Effects of signal failure

In the event of signal failure from the additive tank

sender, an entry is made in the fault memory of the
engine control unit.

27
 Sensors and actuators

The actuators
Particulate filter additive pump V135

S330_150
S330_148

The particulate filter additive pump is of the Each time the fuel tank is replenished, the pump is
reciprocating piston type, which delivers additive to actuated by the engine control unit in a cycle to
the fuel tank. It can be found bolted on the additive ensure the correct amount of additive is added.
tank.

This is how it works:

Additive delivery

Inlet hole
Armature
Pump chamber
To fuel tank
From additive tank

Ball valve
Coil

Spring Pump plunger S330_174

When not energised, the pump is filled with additive. This procedure results in a build up of pressure, which
As soon as the engine control unit actuates the causes the ball valve and thereby the pump chamber to
particulate filter additive pump, the coil is energised open. The volume of additive exactly metered by the
and the armature moves the pump plunger against size of the pump chamber is now delivered to the fuel
spring pressure. The pump plunger closes the inlet tank.
hole to the pump chamber and forces the additive in
the chamber towards the ball valve.

28
Additive intake

Armature chamber
Inlet hole
Armature
Pump chamber
To fuel tank
From additive tank

Ball valve
Coil

Spring Pump plunger S330_176

During intake, the additive flows into the armature

chamber. The magnetic coil is not actuated by the
engine control unit and the spring presses the pump
plunger back. At the same time, the ball valve closes
the pump chamber.

Armature chamber
Inlet hole
Armature
Pump chamber
To fuel tank
From additive tank

Ball valve
Coil

Spring Pump plunger S330_178

The pump plunger moves to the start position.

The vacuum generated as a result draws additive in
through the open inlet hole from the armature
chamber to the pump chamber.

29
 Sensors and actuators

Diesel particulate filter warning lamp K231

The diesel particulate filter warning lamp can be
found in the dash panel insert. It lights up if the diesel
particulate filter is subject to many short journeys, thus
preventing regeneration.

S330_152

Task

If the vehicle is driven over many short journeys, This signal informs the driver that the vehicle should
regeneration of the diesel particulate filter can be be driven at an increased speed consistently for a
impaired. This can cause damage to the particulate short period of time. The increase in exhaust gas
filter and the engine. If the engine is unable to reach temperature, achieved as a result, can burn off the
the necessary operating temperature over a long carbon soot in the particulate filter. The warning lamp
period of time to allow combustion of the carbon soot must go out after this measure.
deposit in the particulate filter, the warning lamp will
light up in the dash panel insert.

The precise details about how to drive the vehicle when the diesel particulate filter warning lamp lights
up can be found in the operating instructions of the vehicle! In any case, the traffic regulations and
speed limits must always be adhered to!

Exhaust emissions warning lamp K83 (MIL)

The emissions relevant components of the diesel particulate filter system are checked for faults and malfunctions
within the scope of the Euro onboard diagnosis (EOBD).
The exhaust emissions warning lamp (MIL = malfunction indicator lamp) shows the faults detected by EOBD.

Detailed information about the exhaust

emissions warning lamp and the EOBD
system can be found in self-study
programme no. 315 "Euro onboard
diagnosis for diesel engines".
S330_188

30
 Functional diagram

Functional diagram

Kl. 30

Kl. 15

K231
J317
J533 J285

G
S S S S
V157
G39 N18 N75
V135

Z19

J248

S330_170

G70 G450
G507 G506 N240 N241 N242 N243
G504

G Fuel gauge sender N18 Exhaust gas recirculation valve

G39 Lambda probe N75 Charge pressure control solenoid valve
G70 Air mass meter V135 Particulate filter additive pump
G450 Exhaust gas sensor 1 V157 Intake manifold flap motor
G504 Fuel additive tank empty sender Z19 Lambda probe heater
G506 Temperature sender before particulate filter
G507 Temperature sender before turbocharger
J248 Diesel direct injection system control unit
J285 Control unit in dash panel insert
J317 Terminal 30 voltage supply relay
J533 Data bus diagnostic interface
K231 Diesel particulate filter warning lamp Colour coding/key
N240-N243 Unit injector valves = Input signal
= Output signal
= Positive
= Earth
= CAN data bus

31
 System limits

Frequent short trips

For the regeneration process to be initiated in the diesel particulate filter, the exhaust gas temperature is increased
by the engine management system.
In the event of frequent short trips, the exhaust gas temperature cannot reach a sufficient level. Regeneration
cannot be carried out successfully. Subsequent regeneration procedures that are carried out with excessively high
levels of carbon deposit can lead to overheating and damage to the particulate filter. The filter could also become
blocked due to a high level of carbon deposit. This blockage in the filter could cause the engine to fail.
In order to prevent these cases from happening, a diesel particulate filter warning lamp will be activated in the
dash panel insert once a specific limit is reached in the filter storage capacity or after a certain number of
unsuccessful regeneration procedures.

Detailed information about the particulate filter warning lamp can be found in this self-study
programme on page 27.

The fuel quality

For effective operation of the system, it is important that the specific ratio between additive and carbon deposit in
the particulate filter is not too low. It should be noted that the fuel must meet DIN standards.
Operation of the vehicle with biodiesel is not possible due to the quality of the fuel currently available and due to
the considerably reduced oxidation stability.
If the fuel contains a high level of sulphur, this can lead to impaired function of the particulate filter system with
higher fuel consumption as a result of increased regeneration.

The emissions
When the regeneration cycle is active, there could be an increase in emissions. During regeneration, there is an
oxidation process from carbon to carbon dioxide (CO2). If there is not enough oxygen available during this
process, carbon monoxide (CO) will also be formed.

To determine the emissions content, an emissions test is carried out (NEDC - New European Driving Cycle).
During this test, the values from the cycle are evaluated with and without regeneration. With the mean values,
the vehicle must meet the EU4 emissions standard.

32
 Service

Maintenance of the particulate filter

In addition to particles of carbon, ash is also collected in the particulate filter. This inorganic ash comprises of the
remains from oil combustion and the iron-rich additive introduced in the fuel. Since the ash cannot be burnt, it
reduces the effective filter volume and thereby impairs the function of the particulate filter over a certain period of
time.
The amount of ash collected in the diesel particulate filter is calculated by the engine control unit. The ash content
reading can be taken using vehicle diagnosis, testing and information system VAS 5052 in a measured value block
in "Guided fault finding" mode.
At an average fuel consumption, the effective service life of the particulate filter is 120,000 km. If fuel consumption
is increased, the diesel particulate filter's service life will be reduced, making it necessary to exchange the filter at
90,000 km.

Once the particulate filter has been exchanged, the ash content figure must be reset to zero using
vehicle diagnosis, testing and information system VAS 5051. If the engine control unit is replaced, the
old ash content reading stored in its memory must be copied using VAS 5051 and then saved in the new
engine control unit. To do this, please refer to the instructions provided in the Electronic Service
Information System (ELSA).

Maintenance of the additive tank

The size of the additive tank is designed to hold enough additive to cover 120,000 km with average fuel
consumption.
If fuel consumption is higher than average, the driver will be informed when the level of additive drops to 0.3 litres
by the preglow control lamp and a fault message in the display of the dash panel insert, prompting him/her to
drive to a workshop.
The additive remains chemically stable for a period of 4 years, even under extreme climatic conditions.
After 4 years, 120,000 km or if a warning is given in the dash panel insert, additive service measures become
necessary. This involves purging of the tank content and replenishment with new additive.

Please refer to the safety measures in ELSA before performing service work on the additive tank.

33
 Service

New special tools

Designation Tool Application

VAS 6277/1 For extracting additive fluid from the additive tank
Extraction unit

S330_164

VAS 6277/2 For filling the additive tank with additive fluid
Filling unit

S330_166

VAS 6277/3
Overflow protec-
tion

S330_168

34
 Test yourself

1. What is the role of the additive?

a) The combustion process in the particulate filter is slowed down by introduction of the additive.

b) The additive has the role of reducing the combustion temperature of the carbon particles to approx. 500C
in order that regeneration of the particulate filter can be carried out even at part-throttle.

c) The additive is mixed with fuel via the fuel return line every time the fuel tank is replenished.
Fuel then burns better and there are less carbon particles generated during combustion in the engine.

2. To reduce exhaust emissions there is a series of different technical solutions.

Which statement is correct?

a) A reduction in emissions can be achieved by measures to the internal workings of the engine.

b) Release of particles that are produced during combustion can be prevented by external engine
measures.

c) The reduction of exhaust emissions can be achieved by switching off internal exhaust gas
recirculation.

3. Which sensors are required by the engine control unit for calculation of the carbon deposit level in the
particulate filter?

a) The lambda probe

b) The air mass meter

c) The temperature sender before turbocharger

d) The pressure sensor 1 before particulate filter

e) The temperature sender before particulate filter

3.)b, d, e

2.) a, b

1.) b

Answers

35
 330

VOLKSWAGEN AG, Wolfsburg, VK-21 Service Training

All rights reserved including the right to make technical changes
000.2811.46.20 Technical status 05/04

This paper was manufactured from pulp that

was bleached without the use of chlorine.