Methacrylate Esters

Safe Handling Manual

Methacrylate Producers Association, Inc. and Methacrylates Sector Group

of the European Chemical Industry Council (2008)
Methacrylate Producers Association, Inc. and Methacrylates Sector Group of the European Chemical Industry Council (2008)

This work is protected by copyright. The Methacrylate Producers Association (MPA) and the Methacrylates Sector Group of the European Chemi-
cal Industry Council (Cefic), which are the owners of this copyright, hereby grant a non exclusive royalty-free license to reproduce and distribute
this work, subject to the following limitations:

1 The work must be reproduced in its entirety, without alterations.

2 All copies of the work must include a cover page bearing MPAs and Cefics notice of copyright.
3 Copies of the work may not be sold or reproduced on the Internet.
 Introduction

Introduction

This Manual provides general information on the safe handling of the esters of methacrylic acid including: Methyl Meth-
acrylate (CAS Number 80-62-6), Ethyl Methacrylate (CAS Number 97-63-2), n-Butyl Methacrylate (CAS Number 97-88-1),
i-Butyl Methacrylate (CAS Number 97-86-9), and 2-Ethylhexyl Methacrylate (CAS Number 688-84-6), and dealing with
specific hazards in an appropriate manner. These hazards include health risks, environmental risks, and the potential of
uncontrolled polymerization.

Properties and characteristics quoted in this Manual refer to the esters of methacrylic acid with a minimum content of 98
percent pure. They conform to specifications reported in the technical information bulletins issued by methacrylate ester
manufacturers. Some of the physical data might be subject to minor changes due to variable concentrations of natural
impurities.

Please read this entire Manual before handling methacrylate esters or before designing a storage system for the esters.
All preventive measures described in this Manual must be followed to minimize the risks associated with this substance.


Safe Handling Manual Methacrylate Esters

Preface

This Manual is a publication of the Methacrylate Producers Association, Inc. (MPA) and the Methacrylates Sector Group
of the European Chemical Industry Council (Cefic) and represents industry best practice. It provides general informa-
tion to methacrylate esters users (Methyl Methacrylate, Ethyl Methacrylate, n-Butyl Methacrylate, i-Butyl Methacrylate,
and 2-Ethylhexyl Methacrylate) about the unique hazards associated with handling these chemicals and measures to be
followed to protect human health, equipment, and the environment. Methacrylate ester hazards include its skin sensiti-
zation, combustibility, and its potential for unanticipated, uncontrolled, and rapid polymerization. Read and familiarize
yourself with this entire Manual before using the information it contains. Also, thoroughly review your suppliers labels
and Material Safety Data Sheet for methacrylate esters before working with them. Additional information is available in
the publication entitled OECD SIAR Short Chain Methacrylate Esters- Ethyl Methacrylate, n-Butyl Methacrylate, iso-Butyl
Methacrylate and 2-Ethylhexyl Methacrylate, pending at time of publication, see http://www.oecd.org/document/63/
0,2340,en_2649_34379_1897983_1_1_1_1,00.html. The information in this manual is current as of the date of publication.
If you have any questions or need more detailed information, you should contact your methacrylate esters supplier.

This Manual was prepared by the following companies that are members of MPA and/or Cefic: BASF SE (European
Union), CYRO Industries (United States), Arkema Inc. (United States), Arkema France (France), Lucite International
(United States, United Kingdom), Repsol Qumica, S.A. (Spain), Rohm and Haas Company (United States) and Evonik
Rhm GmbH (Germany).

For further information contact

Methacrylate Producers Association, Inc.
17260 Vannes Court
Hamilton, VA 20158
USA
www.usampa.org

Methacrylates Sector Group of the European Chemical Industry Council

Avenue van Nieuwenhuyse, 4-B 1
B-1160 Brussels
Belgium

Although MPA and Cefic believe that the information contained in this Manual is factual, it is not intended as a state-
ment of legal requirements with respect to handling methacrylic acid. Consult with legal counsel and/or appropriate
government authorities to ensure compliance with local, regional, national, and international laws and regulations. It is
the customers responsibility to ensure proprietary rights and existing laws are observed. No warranty or representation,
either expressed or implied, is made with respect to any or all of the content of this document and neither MPA nor Cefic
nor its members assume any legal responsibility.


 Properties of Methacrylic Acid Chap 2


Safe Handling Manual Methacrylate Esters

Table of Contents

1 Names 8
2 Properties of Methacrylate Esters 10
2.1 Grades of Methacrylate Esters 10
2.2 Properties and Characteristics of Methacrylate Esters 10
3 Training and Job Safety 12
4 Instability and Reactivity Hazards 13
4.1 Polymerization 13
4.1.1 Overheating and Photo-initiation 13
4.1.2 Contamination 14
4.1.3 Corrosion 14
4.1.4 Inhibitor Depletion 14
4.1.5 Inhibitor Deactivation/Oxygen Depletion 14
4.2 Polymerization Detection 15
4.3 High Temperature Decomposition 15
5 Response to Uncontrolled Polymerization 16
6 Health Concerns 17
6.1 Toxicity 17
6.2 First Aid 17
6.2.1 Contact with the Eyes 17
6.2.2 Inhalation 17
6.2.3 Contact with Skin 18
6.2.4 Ingestion 18
6.3 Industrial Hygiene 18
6.4 Personal Protective Equipment Guidelines 19
6.4.1 All Personnel 20
6.4.2 Routine Work 20
6.4.3 Non-Routine Work 20
6.4.4 Emergencies 20

7 Fire and Explosion Hazard 21

7.1 Special Hazards 22


 Table of Contents

8 Storage and Handling 23

8.1 Drum/IBC/Tote Storage 23
8.1.1 Drum/IBC/Tote Handling 23
8.1.2 Drum/IBC/Tote Emptying 24
8.1.3 Drum/IBC/Tote Disposal 24
8.2 Bulk Storage 24
8.2.1 Pressure Relief 25
8.2.2 Temperature Measurement 26
8.2.3 Level Instruments 26
8.2.4 Pumps and Transfer Lines 26
8.2.5 Materials of Construction 27

9 Shipping 28
9.1 General 28
9.2 Transportation Incidents 28
9.3 Unloading Site 28
9.4 Shipment Unloading 29
9.5 Unloading Tank Trucks with Pressure 30
10 Environmental Considerations 31
10.1 Waste Disposal 31
10.2 Spill and Leak Control 31
10.3 Air Emissions 32


Safe Handling Manual Methacrylate Esters

1 Names

COMMON NAME METHYL METHACRYLATE ETHYL METHACRYLATE

CAS NUMBER 80-62-6 97-63-2

CAS NAME 2-Methyl-2-Propenoic Acid, 2-Methyl-2-Propenoic Acid,

Methyl Ester Ethyl Ester

UN NUMBER 1247 2277

EEC N 607-035-00-6 607-071-00-2

SYNONYMS MMA EMA

Methacrylic acid, Methyl Ester Methacrylic acid, Ethyl Ester
Methyl Methacrylate Monomer Ethyl Methacrylate Monomer
Methyl, 2-methyl-2-Propenoate Ethyl, 2-methyl-2-Propenoate

EINECS NUMBER 201-297-1 202-597-5

CHEMICAL FORMULA

STOICHIOMETRIC FORMULA C5H8O2 C6H10O2

EEC classification Highly flammable Highly flammable

Irritant Irritant

EEC labeling symbols Highly flammable (F) Highly flammable (F)

Irritant (Xi) Irritant (Xi)
R 11-37/38-43 R 11-36/37/38-43
S 24-37-46, note D S 9-16-29-33, note D

Threshold Limit for Preparations 20%: (Xi) 20%: (Xi)

1%: Irritant (Xi/R43) 1%: Irritant (Xi/R43)

IMDG Class 3 Class 3

49 CFR, ICAO, IATA II II

Packing Group

ICAO - CLASS Class 3 Class 3

ADA/RID ORANGE PLATE 339/1247 339/2277

ADR/RID - CLASSIFICATION Class 3 Class 3


 Names Chap 1

N-BUTYL METHACRYLATE ISO-BUTYL METHACRYLATE 2-ETHYLHEXYL METHACRYLATE

97-88-1 97-86-9 688-84-6

2-Methyl-2-Propenoic Acid, n-Butyl 2-Methyl-2-Propenoic Acid, i-Butyl 2-Methyl-2-Propenoic Acid, 2-Ethyl-

Ester Ester hexyl Ester

2227 2283 1993

607-033-00-5 607-113-00-X 607-134-00-4

n-BMA i-BMA 2-EHMA

Methacrylic acid, n-Butyl Ester Methacrylic acid, i-Butyl Ester Methacrylic acid, 2-Ethylhexyl Ester
n-Butyl Methacrylate Monomer Iso-Butyl Methacrylate Monomer 2-Ethylhexyl Methacrylate Monomer
n-Butyl, 2-methyl-2-Propenoate Iso-Butyl, 2-methyl-2-Propenoate 2-Ethylhexyl-2methyl-2-Propenoate

202-615-1 202-613-0 211-708-6

C8H14O2 C8H14O2 C12H22O2

Flammable Flammable Irritant

Irritant Irritant
Dangerous for the environment

Irritant (Xi) Dangerous for the environment (N) Irritant (Xi)

R 10-36/37/38-43, Irritant (Xi) R 36/37/38
note D R 10-36/37/38-43-50 S 26-28, note A
S 24-37-61, note D

20%: (Xi) 20%: (Xi) 10%: (Xi)

1%: Irritant (Xi/R43) 25%: (N)
1%: Irritant (Xi/R43)

Class 3 Class 3 Not subject to dangerous goods

regulations

III III Not subject to dangerous goods

regulations

Class 3 Class 3 Not subject to dangerous goods

regulations

39/2227 39/2283 N/A

Class 3 Class 3 Not subject to dangerous goods

regulations


Safe Handling Manual Methacrylate Esters

2 Properties of Methacrylate Esters

2.1 Grades of Methacrylate Esters

The grades of methacrylate esters usually only depend on the type and amount of inhibitor added to the methacrylate
ester. Specific information is available upon request from producers.

2.2 Properties and Characteristics of Methacrylate Esters

The values in the following table were taken from DIPPR (Design Institute for Physical Properties) where possible. DIPPR
is a subsection of AIChE and specializes in compiling physical property data banks for various chemicals. The following is
the most current information at the time of publication. Contact a manufacturer for more up-to-date information.

10
 Properties of Methacrylate Esters Chap 2

PROPERTIES MMA EMA n-BMA i-BMA 2-EHMA

CAS # 80-62-6 97-63-2 97-88-1 97-86-9 688-84-6

Molecular Weight 100.12 114.14 142.2 142.2 198.31

Boiling Point (C at 101 kPa) 100.5 118.27 163 155 227.67

Freezing Point (C) -48 < -757 -507 -357 < -507

Density (g/cc at 20C) 0.94 0.9127 0.8966 0.883 0.8857

Refractive Index (at 20C) 1.412 1.4115 1.4211 1.42 1.446

Viscosity (mPa-s or cP at 25C) 0.54 0.53 0.94 0.92 2.48

Vapor Pressure (HPa at 20C) 427 20 2.107 2.107 0.0657

(mmHg at 20C) 327 15 1.587 1.587 0.0497

Flash Point, 10 11 20-21 4910 41 929

(Tag Closed Cup, C)

Water Solubility
(G/100G at 20C)
Monomer in water 1.67 0.4697 0.036 0.0477 0.00016
Water in monomer 0.996 0.646 (25C)7 0.3 - 0.46 (25C)7
0.36 0.146

Explosive Limits
(101 kPa, 760 mmHg)
Lower 2.1 1.8 21 1
Upper 12.5 9.6 81 7.4

Latent Heat of Vaporization

KJ/Mole 39.5 40.6 50.0 47.2
Kcal/Mole 9.4 9.7 11.9 11.3

Heat of Polymerization (KJ/Mole) 54.03 59.16 56.66 59.96

Specific Heat (20-30C)

KJ/Kg-K 1.90 1.70 1.97 1.89 2.016
Cal/g-C 0.45 0.41 0.47 0.45 0.486

Partition Coefficient
Log Pow (Octanol/Water) 20C 1.385 1.877 2.99-3.037 2.99-3.037 4.95-5.597
Henrys Law Constant (Pa-m3/mol at 20C) 25-345 14-855

Autoflammability (C) 435 370 294 390

Tg of Polymer (C) 1056 656 206 486 -106

Odor Threshold (ppm) 0.24 0.178 0.0162 0.078 0.768

1 Chemical Properties Handbook

2 Storage and Handling of Acrylic and Methacrylic Esters and Acids, Rohm & Haas, December 1987
3 Heats of Polymerization of Acrylic Acid and Derivatives, Evans and Tyrrall, Journal of Polymer Science, Vol 2, No 4, 1947
4 Handbook of Environmental Data on Organic Chemicals, Karel Vershuersen
5 http://www.dep.state.pa.us/physicalproperties/_cgi-bin/CPP_Search.idc
6 San Esters Corp. (www.sanesters.com)
7 SIDS Initial Assessment Report, Methacrylates Producers Association, 2004
8 ICI Product Bulletin, April, 1994
9 Polymer Handbook, 4th Edition, Wiley & Sons
10 Penske Marten Closed Cup

11
Safe Handling Manual Methacrylate Esters

3 Training and Job Safety

Many of the methacrylate esters are considered to be hazardous under the Occupational Safety and Health Administra-
tions (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the current EU Classification Packaging and
Labeling of Dangerous Substances Regulations. Therefore, all employees must be provided with adequate health and
safety information and training to handle the methacrylate esters. The training requirements have been spelled out in the
Hazard Communication Standard and the EU Directive.

Before undertaking any training of the employees who are engaged in handling or processing any of the methacrylate es-
ters, the supervisor who will conduct the training must be thoroughly familiar with the storage, handling, and properties
of methacrylate esters and with any applicable national, state or local governmental occupational safety and health regula-
tions. Thoroughly review the suppliers label and MSDS and consult a safety specialist at your supplier before finalizing a
safety review of your operations involving methacrylate esters.

12
 Instability and Reactivity Hazards Chap 4

4 Instability and Reactivity Hazards

4.1 Polymerization
Methacrylate esters are highly reactive. Polymerization of methacrylate esters can be very violent, involving considerable
heat and pressure and ejecting hot polymer and monomer from the site of polymerization. Generally the lower molecular
weight esters will produce a higher hazard. Therefore MMA, n-BMA, i-BMA, & EMA are more hazardous than 2-EHMA in
the event of an uncontrolled polymerization.

An explosion hazard exists if the material is in a closed or poorly vented container because pressure build-up can occur
very rapidly. Typically, methacrylate esters contain stabilizer levels that provide a shelf life of about 6 months at ambi-
ent conditions and should be used within that time. Exceptions do exist; your supplier should be contacted for shelf life
information for the specific monomer and grade purchased. Commercially available methacrylate esters are inhibited with
stabilizers including: monomethyl ether of hydroquinone (MEHQ, CAS 150-76-5), also known as para-methoxyphenol
(PMP) and 4-Hydroxyanisole (HA). Other inhibitors include: hydroquinone (HQ, CAS 123-31-9), 2,4-Dimethyl-6-tert-bu-
tylphenol (BDMP, DMTBP or Topanol-A/AO30/IONOL K78, CAS 1879-09-0), and 2,6,-Di-tert-butyl-4-methylphenol
(BHT/ Topanol-O, CAS 128-37-0) and others, which prolong the usable shelf life.

Note: Some of these stabilizers are available under alternative trade names. However, concentrations can
vary and it is essential that the concentration of the active stabilizer is taken into account when determining the
amount required in order to achieve the required stabilizer level in the product.

Methacrylate esters must never be handled or stored under an inert atmosphere. The presence of oxygen is required for
the inhibitor to function effectively. A vapor space containing sufficient oxygen should always be maintained above the
monomer to ensure inhibitor effectiveness.

There are five main causes of unintended polymerization of methacrylate esters: overheating and photo-initiation, con-
tamination, corrosion, inhibitor depletion, and inhibitor deactivation (via oxygen depletion).

4.1.1 Overheating and Photo-initiation

Commercially available methacrylate esters are inhibited with MEHQ, HQ, 2,4-Dimethyl-6-tert-butylphenol
(Topanol-A/AO30/IONOL K78), and 2,6,-Di-tert-butyl-4-methylphenol (BHT or Topanol-O) that prolongs the
usable shelf life. However, this usable shelf life is reduced exponentially with increasing temperature. Therefore,
exposure to heat must be avoided. Maintain the temperature of methacrylate esters below 40C (104F), prefer-
ably below 30C(86F). Only store drums in the shade; do not store methacrylate ester drums in the sun. Avoid
extreme temperatures such as storage next to steam pipes or storage in warm rooms. Normal ambient tempera-
tures encountered for bulk storage at any location are generally satisfactory for maintaining stability within the
recommended maximum shelf life (maximum storage time).

Methacrylate esters can polymerize as a result of photo-initiation. Where sight glasses or other transparent sec-
tions are needed for visual observation in methacrylate esters service, they should have covers to exclude light
between observations.

13
Safe Handling Manual Methacrylate Esters

4.1.2 Contamination
Good housekeeping must be exercised to avoid contamination of methacrylate esters. Many compounds are
known to promote polymerization, such as peroxides and compounds which form peroxides and free radicals,
including aldehydes, ethers, amines, azides, sulfuric acid and nitric acid.

Care must be exercised to avoid contamination of monomer with polymerizing methacrylate esters.
Such polymer seeds could be generated in localized or hot stagnant areas, such as deadheaded pumps, and
heated transfer lines.

4.1.3 Corrosion
Corrosion in general can also pose a polymerization hazard. Metal ions such as iron and copper can initiate
polymerization. Metal ions result if there is corrosion in the storage or transportation system. Corrosion can be
caused by using an improper material of construction, accidental introduction of incompatible metals into the
system such as leaving a non-sparking tool in a storage tank, or the contamination of the methacrylate esters with
materials such as acids that are corrosive to normal methacrylate ester systems.

4.1.4 Inhibitor Depletion

Inhibitor is depleted with time. Elevated temperatures accelerate depletion. Observe the recommended storage
time and temperatures to prevent depletion of the inhibitor.

4.1.5 Inhibitor Deactivation/Oxygen Depletion

Dissolved oxygen is necessary for inhibitors to function effectively, acting as the initial, and very efficient, radical
scavenger. Methacrylate esters should therefore never be handled under an oxygen-free atmosphere. A nitrogen/
oxygen gas mixture containing 5-21% by volume of oxygen at one atmosphere should always be maintained above
the monomer to ensure inhibitor effectiveness. Since some of the methacrylate ester vapors in air form flammable
mixtures at room temperature, it may be desirable to use a nitrogen/oxygen gas mixture with less than 21% by
volume of oxygen to avoid flammability. However, the atmosphere above the monomer should contain at least 5%
oxygen to maintain inhibitor effectiveness.

Oxygen is consumed slowly as part of the free radical scavenging mechanism. Thus, the atmosphere above meth-
acrylate esters in a closed system should be periodically replenished with air or nitrogen/ oxygen gas mixture of 5-
21% by volume of oxygen. Large volumes in vessels open to the atmosphere should be gently circulated. Residues
in transfer lines and other stagnant areas should be blown out with a 5-21% oxygen-containing gas mixture, or
should be designed to be self-draining.

14
 Instability and Reactivity Hazards Chap 4

4.2 Polymerization Detection

Methacrylate esters have the potential to polymerize very rapidly, generating a large amount of heat. A temperature rise
that cannot be related to an external heat source should be considered an indication of a runaway polymerization. In that
event, exercise caution, but if a sample can be safely acquired, it can be used to test for the presence of soluble polymer
to confirm polymerization. While presence of soluble polymer confirms an ongoing polymerization, inconsistent sam-
pling can give a false negative result that does not prove anything until all the other indicators (may include multiple
samples) indicate there is no polymerization. To test for polymer in the monomer, add 20 ml of the monomer to 80 ml of
methanol. The polymer is insoluble in the methanol and the mixture will be cloudy if there is any polymer present.

Occasionally on the plant scale, uncontrolled methacrylate ester polymerizations proceed slowly. Therefore, simple tem-
perature rise may indicate an ongoing polymerization. In the case of a slow temperature rise and with note of the caution
below, the presence of soluble polymer in the monomer is one way to verify whether a polymerization is underway before
temperature extremes are reached.

See Section 5. Response to Uncontrolled Polymerization for more information.

caution
Even slow polymerization has the potential to accelerate into a runaway reaction. If the temperature rises above
45C (113F) or the rate of rise is greater than 2C (3.6F)/hour, and no source of external heat has been identified,
this should be considered as the onset of polymerization. If the temperature rises at a rate greater than 5C (9F)/
hour or the temperature reaches 55C (131F), the situation is critical.

4.3 High Temperature Decomposition

Not all polymerization incidents involve rapid polymerization. Sometimes the reaction proceeds much more slowly. Still,
in unvented containers or containers whose vent has plugged (note that small vents can plug easily because of polymer-
ization of condensed monomer vapors which are likely to be uninhibited), high temperatures and pressures can build up
over time. If the temperature reaches approximately 195-200C (383-392F), methacrylate esters will undergo degradation.
Some evidence exists that methacrylate esters can undergo decarboxylation at approximately 195C (383F) generating
carbon dioxide. With a decomposition reaction, very high pressures can be generated in a short period of time in an
unvented container. Rupture of the vessel is possible.

Note: In the event of an unintended polymerization in an unvented container, high pressures may persist long
after the polymerization event is over because of the presence of decomposition gases.

15
Safe Handling Manual Methacrylate Esters

5 Response to Uncontrolled Polymerization

The techniques for responding to an uncontrolled polymerization of methacrylate esters have been reviewed by the Manu-
facturers. These will be updated as new information is developed. Use the information below to develop local Emergency
Response Procedures. This section alone is not intended to serve as an Emergency Response Procedure by itself.
Approaching any container of methacrylate esters that is thought to be undergoing an uncontrolled polymerization is haz-
ardous because of the possibility of the containers violent rupture. Do not approach a container of uncontrolled polymer-
izing methacrylate esters without prior emergency planning. Never approach a container of uncontrolled polymerizing
methacrylate esters after it has reached 55C (131F) or if the rate of temperature rise has exceeded 5C/ hour (9F/hour)
with no external heat source. Consider this for all response choices.

The most effective response to an uncontrolled polymerization of methacrylate esters is the remote addition and mixing
of shortstop inhibitor, phenothiazine (PTZ). While other choices, mentioned below, may be less expensive, they are also
expected to be less effective unless done as extra activity to reduce consequences after shortstop inhibitor (PTZ) addition
has already been done.

O
 nce it has been determined that an uncontrolled polymerization is occurring (see 4.2, Polymerization Detec-
tion), establish emergency management control over the area including evacuation if necessary. Safe evacuation
distances depend upon many factors including the rate of polymerization, the likelihood of vent pluggage, and
equipment design (size, vent area, design pressure, etc.), etc. These should be planned for in advance and be a
part of the local Emergency Response Procedures. Consult your supplier for further advice in the development
of your Emergency Response Procedures.
A
 pply cooling water to the exterior of the vessel to reduce the temperature of the methacrylate esters. The local
emergency response team should be able to set up fire monitors to provide fire water for cooling. Externally ap-
plied water may also be effective in knocking down any vapors that may be released.
D
 o not attempt to mix the contents of the container unless shortstop inhibitor has been added to the methac-
rylate esters. If it is determined that it is safe to approach the vessel, the following can be tried to minimize the
consequence of the polymerization.
- Ensure adequate venting area by opening any closed top hatches, especially for tank trucks or rail cars. Cau-
tion: Do not attempt this if the temperature is already above 55C (131F) or if a local pressure gauge indicates
that the vessel is above atmospheric pressure or if the vessel is venting.
- Add the shortstop inhibitor, PTZ, in a concentrated solution or slurry. Handlers of methacrylate esters should
maintain a supply of PTZ for use when needed. MEHQ, HQ and AO30 are not shortstop inhibitors. MEHQ,
HQ or Topanol A / AO30 can effectively extend the shelf life of methacrylate esters only if there is adequate
oxygen in solution. Temperatures significantly above ambient may deplete the oxygen in solution and prevent
MEHQ, HQ and AO30 from working. Temperatures reached during a runaway polymerization will defeat the
functionality of MEHQ or HQ. MEHQ, HQ or AO30 will not have a significant impact if added to a runaway
polymerization of methacrylate esters.
- If impact to the environment and to personnel exposures is acceptable, consider draining the contents of the
container into a diked/bunded area. In this case, vapor release that could cause pressure if contained is now
vented directly to the atmosphere and thus protects the vessel. Fire fighting foam can be used to slow vapor
release and control exposures and risk of fire.
- Consider moving a mobile container away from people and equipment; barricading of drums/IBC/totes or
totes/IBC is another option.

Note: A vessel undergoing an uncontrolled polymerization may experience high enough temperature to cause
venting. A polymerizing vessel that stops venting may have a plugged vent. The potential for a violent vessel
rupture may exist for many hours. Do not approach a vessel that has ceased venting until remote temperature
sensing indicates that the vessel contents have returned to the ambient temperature.

16
 Health Concerns Chap 6

6 Health Concerns

6.1 Toxicity
The principal acute hazards of methacrylate esters (MMA, n-BMA, i-BMA, EMA, and 2-EHMA) are the propensity of the
liquid and vapors to be irritating to mammalian tissue.

Direct contact may cause irritation of the eyes, skin, nose and throat. Direct contact with skin may also result in the devel-
opment of skin allergy, in which future exposures can cause itching and skin rash.

Although ingestion is not a typical route of exposure to chemicals in the industrial environment, methacrylate esters are
mildly toxic by ingestion, but may cause irritation of the mouth, throat, esophagus, and stomach.

Inhalation of high concentrations of vapors or mists of methacrylate esters will cause irritation of the respiratory tract and
may cause dizziness, lightheadedness, and may even cause someone to pass out. Inhalation of lower concentrations may
produce mild irritation of the respiratory tract.
Various regulatory and occupational health authorities have established exposure limits for the methacrylate monomers.
See Section 6.3 Industrial Hygiene for more information. Your suppliers current label and MSDS should be consulted for
current toxicological information.

6.2 First Aid

In order to minimize adverse consequences of methacrylate esters incidents, all personnel assigned to work with methac-
rylate esters must be aware that prompt and appropriate response is essential. First aid must be administered immedi-
ately. One prerequisite for the proper management of incidents is the installation of a sufficient number of conveniently
located emergency safety showers and eye wash stations.

All injured personnel should be referred to a physician who should be given a detailed account of the incident. Consider-
ation should be given to supplying the physician or hospital emergency room, where medical help will be sought, with a
copy of the suppliers MSDS. Medical management aspects of that document should be reviewed with the physician.

6.2.1 Contact with the Eyes

If even minute quantities of methacrylate esters enter the eyes, the eyes should be irrigated immediately and
thoroughly with water for a minimum of 15 minutes. The eyelids should be held open and away from the eyeball
during the irrigation to ensure contact of water with all the tissues on the surface of the eye and lids. Obtain a
physicians assistance (preferably an eye specialist) or that of another trained emergency health professional as
soon as possible and transport to a suitable clinic or hospital. No oils or oily ointments or neutralizers should be
put in the eyes or on the eyelids unless ordered by the physician.

6.2.2 Inhalation
Personnel affected by methacrylate esters vapors must be moved at once to an uncontaminated atmosphere. If
an individual is not breathing, administer artificial respiration. Obtain a physicians assistance or that of another
trained emergency health professional as soon as possible and transport to a suitable clinic or hospital. If breath-
ing is difficult, trained personnel should administer oxygen.

17
Safe Handling Manual Methacrylate Esters

6.2.3 Contact with Skin

The emergency safety shower should be used immediately to remove methacrylate esters. Once under the safety
shower, immediately remove all clothing and shoes. Wash with large quantities of water. Continue washing for at
least 15 minutes until odor has disappeared. Washing with soap may help remove residual methacrylate esters
from the skin and reduce injury. After showering, get immediate medical attention. No salves or ointments should
be applied unless prescribed by a physician.

All contaminated clothing should be properly decontaminated before reuse. Where decontamination is not
feasible, clothing should be disposed of properly. Contaminated shoes and other leather items cannot be decon-
taminated and should be discarded. Under no circumstances should contaminated clothing be taken home for
laundering.

6.2.4 Ingestion
Although ingestion of chemicals is rare in the industrial setting, in the event of methacrylate esters ingestion the
affected individual should be made to drink large quantities of water. Activated charcoal may be administered.
Do not induce vomiting. Consult a physician.

If the affected individual is unconscious or having convulsions keep the affected individual warm. General rules of
first aid and resuscitation apply under avoidance of self-contamination. Obtain a physicians assistance or that of
another trained emergency health professional as soon as possible and transport to a suitable clinic or hospital.

6.3 Industrial Hygiene

Exposure to methacrylate esters by inhalation, ingestion, or skin or eye contact should be prevented by a combination of
engineering controls and prudent work practices. Engineering controls such as closed systems and local exhaust ventila-
tion should be the primary emphasis and must be in compliance with national, state, and local governmental regulations.
Workplace testing is recommended to determine exposure levels and the personal protective equipment (PPE) needed.
When high exposures are revealed, corrective measures must be taken.

Occupational health standards-setting organizations in many countries have set work place exposure limits for some
of the methacrylate esters. Consult your suppliers MSDS for the most current occupational standards for these com-
pounds. Some typical examples of international occupational standards are given on the next page.

These workplace exposure limits are time-weighted average (TWA) values. In general for a TWA value of 25 ppm short
exposures in excess of 25 ppm are permitted providing that there are offsetting periods below 25 ppm such that the over-
all exposure averages 25 ppm or less for the 8-hour workday. However the exposure over a 15-minute period must never
exceed the short-term exposure limit (STEL) and it should be recognized that short duration, peak exposures, in excess of
the STEL, may be overtly irritating to the respiratory system. Effectiveness of PPE and other exposure controls can only be
verified by workplace exposure measurements.

Given that many of the higher esters do not have exposure limits set at the present time, it would be prudent to adopt an
exposure limit similar to MMA.

18
 Health Concerns Chap 6

International Occupational Exposure Standards (as of November 2007)

Product Country TWA or equivalent (8-hour) STEL

MMA Netherlands 10 ppm

Denmark 25 ppm
Norway 25 ppm
Sweden 50 ppm 150 ppm
UK 50 ppm 100 ppm
Germany 50 ppm
USA (ACGIH) 50 ppm 100 ppm
USA (OSHA) 100 ppm
France 100 ppm 200 ppm
EU IOELV (proposed) 50 ppm 100 ppm

EMA Netherlands 10 ppm

Denmark 25 ppm
Norway 50 ppm
Sweden 50 ppm 75 ppm

n-BMA Netherlands 10 ppm

Denmark 25 ppm
Norway 50 ppm
Sweden 50 ppm 75 ppm

i-BMA Netherlands 10 ppm

Denmark 25 ppm
Norway 50 ppm
Sweden 50 ppm 75 ppm

6.4 Personal Protective Equipment Guidelines

Personal protective equipment (PPE) is not an adequate substitute for engineering controls, safe work practices, and
intelligent conduct on the part of employees working with methacrylate esters. It is, however, in some instances the only
practicable means of protecting personnel, particularly in emergency situations.

Use the guidelines below as a starting point for developing your own PPE procedures. The hazard of each task must be
thoroughly assessed, appropriate PPE must be selected, and training in the correct use, care and limitations of the PPE
must be provided.

Methacrylate esters, particularly the lower molecular weight compounds, permeate quickly through many common glove
materials. The most appropriate glove depends on consideration of a number of factors including the physical strength of
the glove, the degree of manual dexterity required, the amount of permeation through the glove material, the duration of
wear, and perhaps the cost of the glove.

There are a wide variety of elastomeric and laminate gloves available. Common elastomeric glove materials include latex
(natural rubber), neoprene (polyisoprene), nitrile rubber (ABS rubber), butyl rubber, polyvinyl alcohol (PVA), polyvinyl
chloride (PVC), and fluoroelastomers. Laminate gloves are made from heat sealed sheets of PVA between layers of poly-
ethylene.

In permeation tests PVA/Polyethylene laminate and supported PVA gloves performed best (note that PVA can be rendered
ineffective by contact with water if the laminate layer is breached). Butyl and nitrile rubber gloves offer short-term protec-
tion. Latex surgical gloves offer little protection. Contact your supplier for the latest information on glove materials.

Gloves should be stored correctly and changed regularly, especially if excessive exposure has occurred.

19
Safe Handling Manual Methacrylate Esters

6.4.1 All Personnel

All personnel who are in the general area where methacrylate esters are being handled should wear appropriate
PPE. This protective equipment should be worn even if an individual is not planning to come in contact with the
methacrylate esters processing equipment. An anti-statically finished working garment is recommended.

6.4.2 Routine Work

Personnel engaged in routine work with a small risk of limited exposure, such as collecting a sample or operating
processing equipment, should wear the following protective equipment: chemical-resistant gloves, safety shoes,
and chemical splash goggles. Depending on the situation, consider wearing chemical-resistant boots if walking
surface contamination is anticipated. In addition, air-purifying respiratory protective equipment should be worn
if air monitoring has demonstrated that airborne concentrations of methacrylate esters are above the exposure
limit.

6.4.3 Non-Routine Work

Personnel engaged in non-routine work and/or work with moderate risk of exposure such as unloading tank
trucks and rail cars, opening vessels, breaking lines, or cleaning minor spills and leaks, should wear the follow-
ing PPE: chemical-resistant suits, chemical-resistant boots and gloves, and chemical splash goggles. Wear a face
shield and/or chemical resistant hood in the event of opening drums or lines that may be under pressure. Air-pu-
rifying respiratory protective equipment may be worn if airborne concentrations of methacrylate esters are above
the exposure limit. For high concentrations a supplied-air respirator is required.

6.4.4 Emergencies
Any time there is a risk of exposure to airborne concentrations of methacrylate esters in excess of 200 ppm or to
unknown airborne concentrations, full protective gear must be worn. In such events as major spills, vapor clouds
or fire situations, wear full protective gear: a supplied air respirator in positive pressure mode, chemical-resistant
suits, chemical-resistant boots, hardhat, and chemical splash goggles.

In the event of a release of methacrylate esters, the area should be evacuated immediately and should be entered
only by properly trained personnel equipped with appropriate PPE. It is advisable to have several sets of PPE avail-
able at all times. This equipment should be appropriately stored outside of, but near, the area where the methacry-
late esters are used.

20
 Fire and Explosion Hazard Chap 7

7 Fire and Explosion Hazard

All methacrylate esters with the exception of 2-EHMA can form readily ignitable vapours at ambient temperatures.
Methacrylate esters are typically handled at ambient temperature. The flash points and other flammability characteristics
are listed in Section 2.2. Ignition sources can be spark discharges from static electricity or any other source. Ignition may
also occur, if excessive amounts of mist or aerosol have formed in the air. Vapors are heavier than air and may travel a
considerable distance to a source of ignition and flash back. Containers may explode in fire or when heated because of
polymerization.

All methacrylate esters are immiscible in water. Consequently water may be ineffective to fight a fire. However if a fire oc-
curs in or close to a tank farm containing methacrylate monomers, tanks and pipes should be cooled to prevent mono-
mers from polymerizing by spraying with plenty of water. Effective fire extinguishing agents include dry chemical, foam,
and carbon dioxide.

During transfer between containers, the containers must be electrically interconnected (bonded) and properly grounded/
earthed. Splash filling into a tank must be avoided. This can be achieved by using a dip tube. If mixing nozzles are used in
storage tanks, the minimum storage volume should be chosen such that the liquid surface is 500 mm (20 inches) above
the nozzle outlet at all times in order to avoid spraying.

In the event of major incidents involving large spills or fires in storage tanks or rail cars, an assessment of all pertinent
facts is critical to the safe management of the situation. Factors to consider are the probability of a vapor cloud and its
dispersion, explosion, and the effect of the fire and heat on surrounding objects or materials. Some situations in the past
have been best managed by allowing a fire to burn out.

The low flash points of the lighter methacrylate esters require that all permanent storage tanks be fitted with the legally
obligatory fire protection equipment. Outlets into the atmosphere may require flame arrestors and detonation traps
should be considered for manifolded vents, particularly if the vent is connected to an ignition source, such as a thermal
oxidizer or flare. In case of fire, evacuate non-essential personnel to a safe location. Carbon dioxide or dry chemical extin-
guisher may be used on fires. Water spray, fog or alcohol or universal-type foam may be used on large fires.

Containment of runoff of fire fighting materials should be planned as required by regional, country, state or local authori-
ties. See Section 6.4.4, Emergencies, for PPE to be worn for all emergencies. Also use appropriate PPE during fire fighting.

21
Safe Handling Manual Methacrylate Esters

7.1 Special Hazards

Any drums or containers exposed to fire should be kept cool with water spray while personnel are fighting the fire. Fire
fighting personnel should operate from a remote location if possible. In a fire, sealed containers may rupture explosively
due to polymerization and autoignition of the vapors may occur.

Do not cut, drill, grind, or weld near drums/IBC/totes. The heat from such work could ignite residual material in the
drum/IBC/Tote. Residual vapors in drums or containers may explode on ignition. Improper disposal or reuse of drums/
IBC/totes may be dangerous and/or illegal.

A wet scrubber using an aqueous caustic solution with organic amines can efficiently treat methacrylate ester vapors. For
the final off gas purification, an active carbon cartridge can be used if protected from high organic loading. The heat of
adsorption on active carbon is unusually high for all methacrylate monomers. Therefore, if highly loaded exhaust gases
come into contact with active carbon, ignition is likely to occur.

CAUTION
Active carbon cartridges must never be used for the removal of methacrylate esters from exhaust gases, unless
the gases are pre-treated, e.g., in a wet scrubber.

For the prevention of a back flash into the tank, carbon cartridges must always be isolated from the bulk storage tank by a
flame suppression system (i.e., flame arrestor, scrubber, etc).

The above information should be used to develop a Fire Emergency Response Plan.

22
 Storage and Handling Chap 8

8 Storage and Handling

The stability of methacrylate monomers and the proper methods for handling methacrylate monomers safely are deter-
mined by the following factors:

 oxicity (see Section 6.1)

T
Dissolved oxygen (see Section 4.1.5)
Effectiveness of inhibitors and the storage life of monomers at various temperatures
Flammability
Effect of materials of construction on the stability and other properties of monomers.

Other important stability and safety factors include the physical and chemical properties of the monomers, their odors,
their impact on the environment, their sensitivity to environmental conditions, light and the presence of a water layer
(commercially supplied inhibitors are more soluble in water, and therefore, tend to diffuse out of the monomer phase and
into the aqueous phase, rendering the monomer uninhibited). Please read this entire Manual before storing methacrylate
monomers or before designing a storage system for methacrylate monomers. All preventive measures described in this
Manual must be followed to minimize the possibility of violent polymerization. See Section 4, Instability and Reactivity
Hazards, for a description of the polymerization hazards.

8.1 Drum/IBC/Tote Storage

Methacrylate monomers are sold in steel or HDPE drums. In some regions of the world, reusable stainless steel drums
may be used. IBC/totes of various constructions (including ultraviolet radiation protection) may also be used and should
be treated similarly to drums. Drums/IBC/totes should be electrostatically safe due to the flammability of the materials
being stored.

I n order to ensure inhibitor effectiveness, drums/IBC/totes are initially filled so that a vapor space containing sufficient
oxygen is maintained. Oxygen is consumed slowly as part of the free radical scavenging mechanism. Consult your sup-
plier for the drum/IBC/tote shelf life.

T he drums/IBC/totes must be stored according to applicable national, state and local regulations. Lacking other
guidance or limits, drums/IBC/totes should be stored not more than 2 high and a path of 1.5 meters (5 feet)
should be kept free around each block, to provide ventilation and both normal and emergency response access.
Indoor storage is recommended. Avoid any exposure to the heat of direct sunlight. Warehouses must be well
ventilated.
If sheds are used for the outdoor storage of drums/IBC/totes, they should be constructed of non-combustible
material, be well ventilated and shield the drums/IBC/totes from the sun. They should also conform to the ap-
plicable requirements of underwriters and insurance companies.
Avoid exposure to elevated temperatures.

8.1.1 Drum/IBC/Tote Handling

When a carload or truckload of drums/IBC/totes is received, open the doors carefully. Leave the doors open for a
while to allow any potential odors to dissipate before entering. If a strong, persistent odor is present, indicating a
leaking container, immediately call the supplier. See Section 10.2, Spill and Leak Control.

23
Safe Handling Manual Methacrylate Esters

8.1.2 Drum/IBC/Tote Emptying

Before drums/IBC/totes are opened, they must be supported and grounded/earthed as well as bonded to the pipe
and pumping equipment. A static-free dip pipe or flexible stainless steel hose must be used to drain the mono-
mers. Operations should be conducted with adequate local exhaust ventilation to minimize personnel exposure
and the dangers from spillage and the escape of vapors.

Drums/IBC/Totes and fittings should never be struck with tools or other hard objects that may cause sparking or
puncture. Use non-sparking hand tools when opening flammable monomer drums/IBC/totes.

An overhead vapor space must be maintained in the drums/IBC/totes to provide additional oxygen for polym-
erization inhibition and to prevent over-pressuring of the drums/IBC/totes. Do not use an inert gas, such as
nitrogen, as a vapor pad on the drum/IBC/tote.

Note: Drum contents may be under pressure or vacuum.

When removing plugs (bungs) from a drum of methacrylate monomers (or opening an IBC/Tote), the opera-
tor should wear PPE recommended in Section 6.4, Personal Protective Equipment Guidelines, and should use a
bung, or plug wrench. The operator should place the drum bung up, and loosen the bung. Note that the drum/
IBC/tote contents may be under pressure or vacuum. After the plug starts to loosen, it should be given not more
than one full turn. If internal pressure exists, it should be allowed to escape to the atmosphere. Only then should
the operator loosen the plug further and remove it.

Pumping is the best method to empty drums/IBC/totes. Note that electric pumps must comply with the area elec-
trical classification. Drums/IBC/Totes may be emptied by gravity using self-closing valves. Do not use pressure to
displace drum/IBC/tote contents.

Do not cut, drill, grind, or weld near drums/IBC/totes. The heat from such work could ignite residual material in
the drum/IBC/Tote. Residual vapors may explode on ignition.

Improper disposal or reuse of drums/IBC/totes may be dangerous and/or illegal.

8.1.3 Drum/IBC/Tote Disposal

Empty drums/IBC/totes are hazardous because of residual liquid and vapor. Dispose of drums/IBC/totes in ac-
cordance with applicable regional, national, state, and local requirements. Before a drum/IBC/tote is scrapped, it
should be repeatedly washed with water to remove traces of the methacrylate ester and then rendered unusable by
crushing or piercing. Dispose of rinse water properly. See Section 10.1, Waste Disposal.

8.2 Bulk Storage

Methacrylate monomers must be stored under an atmosphere containing 5-21% oxygen. Suppliers can provide informa-
tion on special design features required to cope with specific hazards of bulk storage. Consider consequences/risk when
planning an installation. Larger bulk quantities of the methacrylate monomers imply higher risk because of higher poten-
tial consequences. Methacrylate monomers are normally stored at ambient temperatures. Equipment should be installed
for effective monitoring of temperature and appropriate alarms to warn of possible unscheduled polymerization events.
An effective maintenance plan, including control devices, is critical. Conduct a hazard review and/or risk analysis of the
storage facility to ensure adequate safeguards are in place to reduce the risk of polymerization and exposure.

24
 Storage and Handling Chap 8

The optimum capacity for a storage tank is a function of the volume and frequency of deliveries of monomer and the
monomer throughput. For the most efficient scheduling of deliveries, storage tanks should have a minimum capacity of
1.5 times the volume of an expected delivery. The best design for an aboveground tank incorporates a vertical shell, a flat
bottom and a conical top. The design selected should allow uniform mixing of the contents with new deliveries. The tank
is set on a concrete pad with a concrete dike of sufficient capacity. A tank well with a bottom drain line through the tank
pad is needed to provide complete tank drainage.

Tanks normally used for methacrylate ester storage should be painted white or insulated to minimize heat absorption dur-
ing the summer months. Tanks should be electrically grounded and effectively bonded to connected equipment.

For environmental and regulatory reasons, tanks and pumps should always be positioned in a diked/bunded area. All ap-
plicable regional, national, state and local governmental regulations must be observed.

8.2.1 Pressure Relief

There is no guaranteed or warranted method for relieving the pressure from a methacrylate ester runaway polym-
erization reaction and the consequent potential of violent rupture of the container. Therefore, low design pressure
(API atmospheric) tanks are recommended. Although no detailed experience with runaway reactions in full-size
tanks is available, weak seam or frangible roof designs are believed to provide the best protection from a failure.
Roof guide cables should be considered to control the trajectory of such a roof. In addition, oversized rupture
disks or weight-loaded lids (weighted manway cover) may be acceptable. Emergency venting devices normally
used for flammable liquids are considered to give adequate fire protection; however this type of device will not
provide adequate relief in the event of an uncontrolled or runaway polymerization.

For the natural breathing of the tank, a conservation valve should always be installed. Various designs, such as
weighted pallet or breathing valves with flexible diaphragms are commercially available. Seal pots with glycol can
be used instead of conservation vents if they are properly designed and maintained. They may also serve as an
overflow device.

Uninhibited methacrylate ester vapors can condense on cold surfaces, such as relief valve inlets or rupture disks.
The uninhibited condensate may then polymerize. Pressure relief devices and their connected lines should be
checked periodically for the presence of polymer, to prevent interference with their proper operation. Relief valves
and nozzles can be electrically traced and insulated to help control polymer formation by preventing condensa-
tion.

A vent line and associated devices are required to prevent corrosion and polymerization by providing a blanket of
dry, oxygen-containing atmosphere over the monomer, to dispose of vapors and to reduce fire hazard and odor. If
a dryer or overflow pot is used, it should be checked frequently for plugging by polymer from condensed uninhib-
ited monomer.

A drying agent can be used to provide a dry vapor space over the monomer to eliminate water contamination. It
can be installed on the vent line, pad gas line, or conservation valve inlet line. The drying agent is usually renewed
every 3 to 6 months, depending on local climatic conditions. Care should be taken to prevent blocking due to poly-
mer. Alumina, molecular sieves, and calcium chloride are typical desiccants.

Environmental protection alternatives, such as containment of vapors with closed loop unloading or venting
through a scrubber or incinerator, should also be considered.

25
Safe Handling Manual Methacrylate Esters

8.2.2 Temperature Measurement

Redundant temperature-sensing elements should be installed. A temperature alarm should also be installed as
a monitor and safeguard to warn of polymerization. At least two independent temperature-sensing elements
(thermocouples) should be installed near the tank bottom to ensure that they are always submerged in the liquid.
In larger tanks it is sometimes advantageous to have a second pair of sensors installed above the lower third of
the total tank height.

The temperature monitoring system should be capable of determining the absolute temperature of the bulk liquid
as well as the rate of temperature rise. Recording the temperature is helpful, and the use of high temperature
alarms is strongly recommended. If an alarm is used, it should activate at a temperature about 5C above the
normal maximum temperature of the stored liquid.

8.2.3 Level Instruments

A steel or stainless steel differential pressure transmitter purged with dry, oxygen-containing gas is preferred as
the level-measuring device. This will provide continuous level readout, at any remote location, with alarm capabili-
ties. A high level alarm at 85 - 90% of the tank capacity is suggested, coupled with a high level switch set at 90 -
95% which should close a valve on the tank feed line. An ultrasonic type switch is preferred; float switches tend to
have problems with plugging from condensed uninhibited monomer that has polymerized. A capacitance probe
would be a secondary choice. Manometer-type level gauges or equivalent are preferred over gauge glasses, should
the differential pressure style not be used.

8.2.4 Pumps and Transfer Lines

Care must be taken to ensure that pumps and transfer lines are never positioned close to a heat source such as
radiators or steam pipes. In the event of polymerization, polymer adhering to pump rotors can exert centrifugal
forces strong enough to shatter operating pumps.

Centrifugal chemical pumps, self-priming centrifugal pumps, or seal-less pumps (such as magnetic coupled or
canned motor pumps with external cooling) are appropriate for transfer service for methacrylate monomers.
Mechanical seals are typically used. Centrifugal pumps either packed or with a gliding disk seal, may require more
maintenance due to the poor lubrication properties of the methacrylate monomers. For magnetic drive or canned
pumps, a temperature sensor must be installed within the pump body. Canned motor pumps and cooled pumps
with magnetic coupled drive have excellent performance properties with respect to leaks, but are sensitive to
dry operation that usually leads to total loss of the pump. Therefore, a low/no flow switch or level control device
should always be installed to protect pumps from dry operation or dead heading.

CAUTION
If seal-less or canned pumps are used, heat generation can cause polymerization in the pump if flow is stopped.

Care must be exercised to avoid deadheading of pumps since this might overheat the monomer. A temperature
sensor or a flow control device combined with a motor switch should be installed on the pump discharge side and
before the shutoff valve, preferably in the pump housing. Centrifugal pumps present the potential for dangerous
splashes if methacrylate monomer leaks through pump seals or glands. Therefore, pump glands, flanged fittings,
and valve stems should always be provided with splash collars.

26
 Storage and Handling Chap 8

Piping should be cleaned of all grease and scale that may be adhering to the inner walls, after installation.
All pipes should be painted white or otherwise protected from the heat of direct sunlight. All pipes should be
pitched to drain and have no dead-legs. Pipelines and associated systems that will be dormant should be drained
and cleared. Any monomer remaining in the lines may polymerize rapidly.

CAUTION
Inert gas (nitrogen or other non-oxygen containing gas) should not be used to blow pipelines clean. A mixed gas
with at least 5% oxygen should be used to clear lines. If flammability protection is desired the mixed gas should
be less than 10% oxygen; 8% oxygen is preferred. Care should be used when blowing flammable material lines
with air. If static charges develop, an ignition could occur. Some regulations forbid the use of air pressure to move
flammable liquids. Thermal expansion of liquid in blocked lines can develop substantial pressure resulting in
damage and spills. Use care in designing your systems to avoid these potential problems.

To limit vapor emissions during monomer transfers, it is advisable to use a vapor return line to allow the ex-
change of monomer vapors between the vapor space of the storage tank and the shipping container. The vapor
return line (back-venting pipe) in a closed loop unloading system should be designed with a slight inclination
toward the storage tank so that condensed liquid can drain back into the tank. The vapor return line should be
equipped with a shut-off valve on the end connected to the transport vessel. Some locations may also require a
flame arrestor on the end close to the tank.

8.2.5 Materials of Construction

Preferred construction materials for tank, pump and pipe installations are steel or stainless steel. Polyethylene,
polypropylene, or fluoropolymers are also suitable as materials of construction for methacrylate monomers and
may be useful for accessory equipment such as gaskets and valve parts. Rust particles or other particulate matter
can be satisfactorily removed from monomers by means of a white cotton fiber or polypropylene wound on a
stainless core, or stainless steel mesh cartridge filter. Note: Cotton has been known to shed small fibers. Choose
materials carefully.

27
Safe Handling Manual Methacrylate Esters

9 Shipping

9.1 General
Governmental regulations prescribe how to package, mark, label, placard and describe materials on shipping documents,
depending on the quantity and type of hazardous material and the method of transport. Employees shipping, receiving
and unloading hazardous materials must be trained in the proper application of these regulations.

Methacrylate esters must be shipped with an oxygen-containing atmosphere to maintain inhibitor activity. Pure oxygen
or any inert gas should not be used for sparging, blowing lines, or blanketing. Pure oxygen lowers the flash point, thus
increasing flammability. Inert gases can reduce dissolved oxygen sufficiently to inactivate inhibitor and cause a polymer-
ization. Air or a gas mixture of 5 to 21% by volume oxygen is preferred when handling methacrylate esters.

Cleanliness of the transport vessels is essential to prevent contamination that can cause polymerization. Rail cars, trucks
and isotanks used in other service should be cleaned and dried before reuse and should be free of polymer. Containers
must be free of contamination before loading to avoid polymerization of the entire contents.

Maintain vapor space in filled containers and drums sufficient to comply with shipping regulations and to maintain inhi-
bition.

Retained samples should be stored in a cool, dark place for no longer than one year. Amber glass bottles reduce UV initi-
ated polymerization and are recommended for storing small amounts of methacrylate esters.

Protective caps on discharge pipes must be removed with particular care because the pipes may be filled with monomer if
the bottom valve of the container leaks.

9.2 Transportation Incidents

In the event of a spill, fire, or suspected polymerization, immediately contact the appropriate local or national transpor-
tation emergency clearing organization. This would be for instance, TUIS in Germany, CANTREC (Canadian Transport
Emergency Centre operated by Transport Canada [http://www.tc.gc.ca/canutec/en/menu.htm]) in Canada at (613)996-
6666 or CHEMTREC (CHEMical TRansportation Emergency Center [http://www.chemtrec.org]) in the US at (800)424-
9300.

If a shipment in a railcar, tank truck, drum, intermediate bulk container [IBC/ tote] becomes damaged so that delivery
cannot be made safely, every effort should be made to move the container away from people and property. Police and fire
departments are to be notified and the public is to be restricted from the area.

9.3 Unloading Site

Facilities and policies must foster prompt detection of and response to abnormal events. Unloading should be continu-
ously monitored until completed. Storage tanks high-level alarms should be audible in the unloading area. Automatic
shutoffs can prevent overfilling of storage tanks. Storage tanks with high-level shutoffs should be periodically tested to
verify proper operation. Unloading at night is discouraged. When it is necessary to unload at night, proper and adequate
lighting should be provided in the working areas to control unloading hazards.

28
 Shipping Chap 9

Adequate facilities and procedures to handle leaks and spills are essential. An emergency shower and eyewash must be
provided, directly accessible to the loading and unloading area. Other sources of water should be available to wash down
minor spills. PPE should be worn as suggested in Section 10.3. Unloading areas should have containment to collect and
control spills. Drainage should be directed away from the unloading area. Installation of a collection pit as a containment
for spills is recommended.

Ergonomic and physical safety must be considered in design of unloading sites. The unloading area should have stairs
and a platform if access to the top of the tank truck or railcar is required. Facilities should consider the need for fall arrest-
ing systems. Overhead unloading hoses or arms should be counter-balanced to avoid lifting injuries.

Equipment should be appropriately designed for unloading, including:

A grounding cable must be attached to bulk containers before and during unloading to prevent ignition due to
static discharge.
Unloading piping should be arranged so that the material drains toward the storage tank when transfer stops.
Unloading areas should be of noncombustible construction. The unloading area should be designed and ar-
ranged so that the truck is driven into and off the pad in a forward direction, without having to back equipment
into position.
Packing and lubricant for pumps, glands, etc. must be of a material compatible with methacrylate ester
handling.
Pumping from containers is highly recommended/preferred.
Never use inert gas.
A dedicated unloading hose should be used to avoid contamination. A regular physical inspection cycle to
examine hose gaskets, cleanliness, and exterior condition is recommended. Periodic pressure checks or replace-
ment can also help assure hose integrity.

Personnel should wear the following PPE whenever making or breaking connections, including bulk unloading:

C hemical resistant splash suit.

Chemical resistant gloves.
For added protection against chemical exposure, chemical resistant boots or overshoes can be worn over
leather safety shoes.
Eye protection of safety glasses with side shields; chemical goggles and/or face shield and NIOSH-approved
respiratory protection.

9.4 Shipment Unloading

The preferred method to control odors and flammable vapors of methacrylate esters from tank trucks and rail cars is a
closed loop (vapor balanced) system. Displaced receiving tank vapors are returned to the tank truck or directed to vapor
control equipment such as scrubbers, thermal oxidizers, or flares.

Do not use compressed air to unload flammable liquids such as MMA. NEVER use gas exceeding 21% oxygen to unload
or handle flammable liquids. Pure oxygen lowers the flash point, increasing the risk of fire. Use the minimum pressure
necessary to accomplish unloading, never more than 80% of the tank trucks safety relief valve setting. Vapor control
equipment such as a scrubber, thermal oxidizer, incinerator or flare may be necessary to treat displaced tank vapors when
using pressure unloading.

29
Safe Handling Manual Methacrylate Esters

The following unloading procedures are suggested for methacrylate esters to reduce risk of spills, odors and fires.

Prior to connecting or unloading any shipment, the contents should be verified and unloading equipment should be
prepared. Some recommended steps include:

P ositively verify contents by sampling, verifying the bill of lading description, placard verification, and/or other
means.
Locate and test the operation of the nearest emergency shower and eye wash.
Place warning signs or cordon off unloading area to restrict personnel entry.
Inspect and wear required Personal Protection Equipment [PPE] before sampling or making any pipe connec-
tions to the truck.
Visually inspect shipping containers for leaks and other irregularities. US DOT forbids vehicles to use public
roads after a leak is discovered. Arrangements must be made to stop a leak before the tank truck or rail car can
be returned.
Verify that the receiving vessel can hold the entire shipment.
Verify that the intended piping and valve alignments will transfer the methacrylate ester to the proper tank.
Transferring to the wrong tank will contaminate it and may cause a chemical reaction.
For tank trailers, spot the trailer, shut off the engine, set the brakes, have the driver leave the unloading area,
and set wheel chocks.
For rail cars, spot the car, set the hand brake, set wheel chocks, place Tank Car Connected sign on track, and
place derailers or lock out switches beyond accessible ends of the rail car.
Ground the tank trailer or rail car.
To prevent personnel exposure, verify that all valves are closed before removing any caps, plugs, or flanges.

Some recommended steps for unloading a tank truck or rail car include:

C onnect the appropriate line to the vent valve on the shipping container and connect the vapor return hose.
Open the vent valve on the shipping container to equalize the shipping container pressure with the receiving
tank, pressure source, or atmosphere. To prevent implosion of the shipping container do not unload with the
vapor valve closed.
Connect the liquid unloading hose to the shipping containers unloading fitting.
Open the unloading valve(s) on the shipping container. On tank trucks this is often an external (secondary)
manual valve and an internal valve operated by a hydraulic hand pump.
Start the pump.
Monitor hose connections and piping for leaks. Stop transfer if leaks occur. Check that level in receiving tank
rises appropriately. If using vapor return, prevent implosion of shipping container by monitoring pressure gauge
to assure vapor return line is clear and flowing. Remain in the unloading area until transfer is complete.
When the container is empty, shut off pump.
Close the unloading valves, including internal hydraulic valve and external manual valve on tank trucks.
Close the vent valve on the shipping container.
Depressurize and drain the unloading hose, then disconnect it carefully.
Carefully depressurize and disconnect vapor return hose.
Replace caps, plugs, and flanges removed for unloading. Secure equipment covers.
Follow appropriate regulations for securing empty tank truck or rail car for shipment.
Disconnect ground clamp, remove wheel chocks, Connected sign(s), and/or derails. Unlock railroad switches.

9.5 Unloading Tank Trucks with Pressure

It is not recommended to unload tank trucks with pressure. Your supplier should be contacted before this procedure is
used due to the high risk of high velocity liquid leaks in the event of equipment failures and the environmental impact of
such unloading practices.

30
 Environmental Considerations Chap 10

10 Environmental Considerations

Governmental regulations governing waste disposal require that producers and users of chemical products be fully aware
of viable alternatives for the safe disposal of waste materials and to select and practice a disposal method or process
that assures compliance with all applicable requirements. The treatment or disposal of methacrylate esters as a specific
chemical can be determined by comparing the physical and chemical properties with regulatory standards.

Discharges into navigable waters, public or private sewers, or air; disposal in landfills, and by incineration, are all con-
trolled by governmental (local, regional, national, and international) laws and regulations. Noncompliance is subject to
criminal or civil penalties, or both. Spills must be promptly reported to appropriate authorities and cleaned up.

10.1 Waste Disposal

Local regional, national, and international regulations governing waste disposal make it essential for producers, suppli-
ers, carriers, and users of monomers to be fully aware of viable options for the disposal of materials containing meth-
acrylate esters. Materials to be disposed of include residues from production and cleaning operations as well as waste
material from spills.

Methacrylate ester wastes need to be reviewed for proper classification and treatment under national regulations. MMA
and ethyl methacrylate are classified as listed wastes under the US Resource Conservation and Recovery Act [RCRA]
which regulates the generation, transportation, handling, storage, treatment and disposal of hazardous wastes in the US.
The waste identification numbers are: U162 for MMA U118 for EMA and D001 (ignitable) for n-BMA and i-BMA. 2-EHMA
is not a RCRA hazardous waste. In the EU, wastes are classified according to EU Directive 91/689/EEC on Hazardous
Waste. In the UK, methacrylate esters are classified as hazardous under the UK Hazardous Waste Regulations, 2005.
Hazardous wastes may include, but not limited to, process wastes containing methacrylate esters, methacrylate ester
contaminated wastewater, soil, debris, and empty containers.

Diluted methacrylate esters degrade easily in a biological treatment plant and may be treated in an on-site industrial
wastewater treatment plant if allowed by the facilitys discharge permit. Liquid methacrylate esters may also be sent to
local public treatment works with the local authoritys knowledge and approval. Dispose of absorbents or polymeric mate-
rial containing methacrylate esters, by incineration. Liquid wastes can be collected for incineration or burning as a fuel in
an approved permitted facility in accordance with national regulatory requirements.

When disposing of laboratory wastes or retained samples, be certain to keep methacrylate esters separate from incompat-
ible materials, such as peroxides, to prevent polymerization.

10.2 Spill and Leak Control

Emphasis should be placed on the prevention of leaks and spills through careful design and good operating procedures.
Written spill and leak response procedures are recommended and may be required by law.

Even though methacrylate esters are not likely to persist in surface waters over an extended period of time all efforts must
be made to prevent spills from running into public surface waters. Promptly notify responsible pollution control agencies
if methacrylate esters are spilled or released into surface water or to a municipal sewer system. Small spills of up to 5
liters can be suitably absorbed in commercially available spill cleanup kits.

31
Safe Handling Manual Methacrylate Esters

Large spills should be contained, if possible, within a diked/bunded area. Spills can be contained temporarily by stacking
sand bags or similar absorbent material. Avoid run-off into storm sewers routed to public waters.

Various regulatory authorities have rules for reporting certain substances that may be spilled, released, used, or stored by
facilities at certain quantities. It is important for facilities handling methacrylate esters to know and understand the local
rules for release reporting and public information concerning hazardous chemicals in the community.

In the US, MMA and EMA have established CERCLA Reporting Quantities [RQ] of 1000 pounds when released or spilled
into the environment. The National Response Center [NRC] must be notified in the event of a release or spill greater than
1000 pounds. MMA has been designated as a Superfund Amendments and Reauthorization Act (SARA) Title III Section
311/312 hazardous chemical requiring local community notifications. MMA is also a SARA Section 313 chemical requiring
annual reporting of releases from point sources and fugitive emissions.

In the UK releases of methacrylate esters must be reported as per the Reporting of Injuries, Diseases and Dangerous Oc-
currences (RIDDOR) Regulations 1995. Other regulatory authorities have different requirements.

10.3 Air Emissions

Discharges into the atmosphere of gases containing certain chemicals are subject to restrictions in most countries. Air
emissions must therefore be controlled and approved in accordance with applicable air emission control regulations.
Some methacrylate esters are classified as Volatile Organic Compounds [VOC] under the US Clean Air Act. MMA is listed
by the US EPA as a Hazardous Air Pollutant under the Clean Air Act Amendment of 1990. In the EU, the storage and
use of methacrylate esters may fall under the Integrated Pollution Prevention and Control Directive (96/61/EC) and the
REACH Regulation (EC No 1907/2006). Users must be responsible to ensure that their air emissions are in compliance.

Direct emissions to the atmosphere are to be controlled and permitted where necessary. Closed loop or vapor balancing
unloading can be effective in reducing and controlling unloading emissions and odors. Closed loop unloading should
be followed in storage, loading, and unloading facilities. However, there is a danger of contamination when vapor return
lines are connected to a common vent header for multiple storage tanks. Methacrylate ester vapors are uninhibited and if
these condense and collect in the vapor return system they may polymerize causing blockage. Systems should therefore
be designed such that they drain back into the bulk of the product and do not contain dead legs where condensed vapor
can collect.

Exhaust gases rich in methacrylate esters should be scrubbed before being released into the atmosphere. The exhaust gas
can be incinerated in a flare if one is conveniently available. Catalytic incineration is a further option.

Methacrylate esters can be readily scrubbed with a sodium hydroxide and/or amine solution from vent gases. Depleted or
spent scrubber solution can be drained into a biological treatment plant or incinerated, if permitted.

Please be aware that these regulations are constantly developing and other regulations may apply. Contact a manufac-
turer for the most current MSDS for more complete and up to date information.

32
33
Methacrylates sector group Methacrylate producers association, inc.
Cefic aisbl - European Chemical Industry Council 17260 Vannes Court
Avenue E. van Nieuwenhuyselaan 4 Hamilton, VA 20158 - USA
1160 Brussels - Belgium T +1 540 751 2093
T +32 2 676 72 11 F +1 540 751 2094
F +32 2 676 73 00 www.mpausa.org
www.cefic.org