Manual Programacao Argox As 8000

Download as pdf or txt
Download as pdf or txt
You are on page 1of 34

Leitor Argox

AS-8000 CCD
O Leitor de Cdigo de Barras Manual Argox AS-8000 CCD
ideal para qualquer tipo de comrcio. Com design
moderno, leve e ergonmico capaz de ler todos os
cdigos de barras utilizados no mercado a uma
velocidade de 100 scans por segundo, em uma distncia
de aproximadamente 15 centmetros.
www.bztech.com.br
NOTICE:

This device complies with Part 15 of the FCC Rules.


Operation shall be subject to the following two
conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interface received,
including interface that may cause undesirable
operation.

This equipment has been tested and complied with


the limits for a Class a digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to
provide a reasonable protection against harmful
interface when the equipment is operated under a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interface to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interface in
which case the user will be required to correct the
interface at his own expenses.
Note: All brands and trademarks shall belong to their
respective owner.

Note: Specification is subject to changes without


notice.
Using the ArgoxScan
8000/8120/8150/8250/8310/8312
The ArgoxScan can automatically scan barcode at a distance.

Simply aim and pull the trigger. Code scanning is performed

along the center of the light bar emitted from the reading

window. This bar must cover the entire code.

Successful scanning shall be obtained by tilting the scanner

with respect to the barcode to avoid direct reflections that

impair the reading performance, especially for 2D barcode.


Recommended Steps
When the required settings have been configured, all settings
are stored in non- volatile memory of scanner after reading
EXIT Label. Recommended steps are as follows.
1) Set right host interface for your scanner.
(The scanner is in factory default shown as bold label)
2) Set interface to optimize protocol of scanner with your
host in interface section.
3) Set system control of scanner, such as specific
adjustments double confirm, power saving, indicator
and scanning mode which you prefer usage in system
control section.
4) Set code options of scanner for your usage in code
option section. You must make sure to enable the
symbology first, then Min./Max. code length, code ID
checksum and truncate digits are also converted.
5) Set string format of the scanner, such as preamble,
postamble Prefix, suffix, code ID and code name
transmission for your application in string format
section.
Note: If still not work properly. Please contact your dealer for
further information.

Introduction
Installation- Keyboard Wedge
1) First of all, you must switch off power for the
terminal/computer.
2) Disconnect the keyboard cable from the back of the
terminal/computer.
3) Connect the appropriate interface cable to the scanner
and to the terminal/computer.
4) Turn the terminal/computer power on.
RS-232
1) Disconnect power to the terminal/computer.
2) Connect the appropriate interface cable and external
power supply (DC adapter) to the scanner.
3) Plug the serial connector into the serial port on the back
of your computer/terminal. Tighten the two screws to
secure the connector to the port.
4) Plug the power pack into power source.
5) Once the scanner has been fully connected, turn the
terminal/computer power back on.
USB (Simulate with keyboard wedge)
1) Connect the USB cable between scanner and PC.
2) Windows will automatically detect the USB device.

Note: If any of the above operation is incorrect, turn off the


power immediately and check any improper
connections. Go through all above steps again.
Note: If you need more programming parameters to setup
your ArgoScan scanner, please go to
www.argox.com and download the completed users
manual.

0
Programming the ArgoScan
8110/8120/8150/8250/8310/8312
To program the 8110/8120/8150/8250/8310/8312, you must
scan a series of programming barcode in the correct order.
Fold out the back cover of this manual. You will see a table of
alphanumeric barcodes, which are used to program the
various options presented.

To program each option, you must:


1. Scan the Program barcode on the parameter setting part.
2. Enter the option mode by scanning the Option Bar Code
(also on the Parameter setting part).
3. To the right of the option barcode, the necessary
alphanumeric inputs are listed. Scan these alphanumeric
entries from the back fold out page. To confirm above
steps, you must scan the Finish barcode on the back fold
out page.
4. Once you have finished programming. Scan the Exit
barcode, listed on the lower right hand corner of each
parameter setting part.

1
Interface Selection

Keyboard Wedge

RS-233

Wand Emulation

(8110/8150/8250)

USB

Keyboard

/RS232/USB *

Auto detection

Note:-Default

Keyboard Layout

USA *

Belgium

Danish

2
Keyboard Layout - Continued

France

Germany

Italian

Portuguese

Spanish

Swedish

Switzerland

UK

Latin American

Japanese

3
RS-232 Flow Control

None *

RTS/CTS

Xon/Xoff

ACK/NAK

RS-232 Baud Rate Setting

300 BPS

600 BPS

1200 BPS

2400 BPS

4800 BPS

9600 BPS *

4
RS-232 Baud Rate Setting
(Continued)

19200 BPS

38400 BPS

RS-232 Parity Setting

None *

Odd

Even

RS-232 Data Bit Setting

8 bits *

7 bits

5
Pin Assignments
AS Series 8-pin RJ-45 Connector

Pin RS-232 Keyboard


1 VCC (+5V) VCC (+5V)
2 TXD NC
3 NC CLK / PC
4 NA DATA / PC
5 CTS DATA / KB
6 RXD NC
7 RTS CLK / KB
8 GND GND

1
1 2
3
2 5 4
3 6
5 46 7
8
7 9
8 10

8-pin 10-pin

AS Series 10-pin RJ-45 Connector

Pin RS-232 Keyboard


1 I/F I/F
2 VCC (+5V) VCC (+5V)
3 TXD NC
4 NC CLK / PC
5 GND DATA / PC
6 CTS DATA / KB
7 RXD NC
8 RTS CLK / KB
9 GND GND
10 NC GND

6
Keyboard Wedge Combo Connector (To Host Side):

Pin Mini-DIN 6P Male DIN 5P Female


1 DATA / PC DATA / KB
2 NC NC
3 GND GND
4 VCC (+5V) VCC (+5V)
5 CLK / PC CLK / KB
6 NC NC

5 DIN 5P Female Connector


4
3

2
1 4
6 2

1
Mini-DIN 6P Male Connector 5 3

RS-232 DB-9F Connector (To Host Side):

Pin Definition
1 NC
2 TXD
3 RXD
4 NC
5 GND 5
9
4
6 NC 3
8
7
7 CTS 2
6
8 RTS 1

9 VCC (+5V)

7
Keyboard Wedge PS/2 Connector (To Host Side):

Pin Mini-DIN 6P Male Mini-DIN 6P Female


1 DATA / PC DATA / KB
2 NC NC
3 GND GND
4 VCC (+5V) VCC (+5V)
5 CLK / PC CLK / KB
6 NC NC

4 6 Mini-DIN 6P Female Connector


2

1
3 5

6 4 2

1
Mini-DIN 6P Male Connector 5 3

8
Scan Mode

Good-read off

Momentary *

Alternate

Timeout off

Continue

Test only

Stand Mode Enable

Stand mode

9
Suffix Characters Setting
(Keyboard Wedge & USB)

Enter *

Tab

None

10
Enable Barcode

Industrial 2 of 5

Matrix 2 of 5 Eur

Standard 2 of 5

Codabar

Code 93

Code 11

MSI/Plessey

UK/Plessey

Telepen

China Post

Italian Pharmacode

(Code 32)

Code-16K

(for 8250/8312)

11
Enable Barcode - Continued

EAN UCC Composite

(for 8312)

RSS-14

RSS-Limited

RSS-Expanded

Micro-PDF

(for 8312)

Note: All other barcodes not listed in the table are set to be
enabled in default.

12
UPCA Supplement digits
(for 8120/8150/8250)

None *

2 digits

5 digits

UCC/EAN 128

Auto detection

13
UPCA Supplement digits
(for 8310/8312)

None *

2 digits

5 digits

2, 5 digits

UCC/EAN 128

2, UCC/EAN 128

5, UCC/EAN 128

All

14
UPCE Supplement digits
(for 8120/8150/8250)

None *

2 digits

5 digits

UCC/EAN 128

Auto detection

15
UPCE Supplement digits
(for 8310/8312)

None *

2 digits

5 digits

2, 5 digits

UCC/EAN 128

2, UCC/EAN 128

5, UCC/EAN 128

All

16
UPCA Truncation/Expansion

None *

Truncate leading zero

Expand to EAN-13

UPCE Truncation/Expansion

None *

Truncate leading zero

Expand to EAN-13

Expand to UPCA

UPCE Expansion

None *

Truncate leading zero


17
EAN-13 Supplement digits
(for 8120/8150/8250)

None *

2 digits

5 digits

UCC/EAN 128

Auto detection

18
EAN-13 Supplement digits
(for 8310/8312)

None *

2 digits

5 digits

2, 5 digits

UCC/EAN 128

2, UCC/EAN 128

5, UCC/EAN 128

All

19
EAN-8 Supplement digits
(for 8120/8150/8250)

None *

2 digits

5 digits

UCC/EAN 128

Auto detection

20
EAN-8 Supplement digits
(for 8310/8312)

None *

2 digits

5 digits

2, 5 digits

UCC/EAN 128

2, UCC/EAN 128

5, UCC/EAN 128

All

21
ISBN/ISSN Conversion

Disable *

Enable

EAN-8 Expansion

None *

Truncate leading zero

22
Code 39 Check-sum setting

Verification Disable *

Verification Enable

Transmit Disable *

Transmit Enable

Code 39 Format setting

Standard *

Full ASCII

Append Disable *

Append Enable

Start/End Tx Disable *

Start/End Tx Enable

23
 
  

  

            



CODABAR-PARA (8110 *)

CODE-11 PARA

CODE-128 PARA *

CODE-39 PARA *

CODE-93 PARA

EAN-13 PARA *

24
PDF-417 (8250/8312 *)

STANDRAD-25 PARA

CODE-16K


EAN-8 PARA *

INDUSTRIAL-25 PARA

UPCE PARA *

25
INTERLEAVED-25 PARA *

MATRIX 25 PARA

MSI/PLESSEY PARA

UPCA PARA *

UK/PLESSEY PARA

GS1 Databar

Micro-PDF (8312 *)

26
ASCII Code Table    

  
! " # $ # $
# '% &( ( %)! *'!+
$ )-, .$ /102" *134$
5 *16748 .5 /9: *13 5
; !<= > . ; + 9: *13 ;
? @'A BCD> . ? +E0F9 *131?
G H B )', .G +1%-I %JLK
M H B *'8 .M JN3NK /OL%
P . P Q +1! +9 Q
R Q S .R Q / 3TJF%
U 9VW .U "T9 +TX
J .E$Y# !. /') Q
Q "16Z[< + SD\ ] 9 +E/13
3 +E8^ .E$$ . . ./
* +E8D>_<a` .E$ 5 3N@ b4/
+ c 8 S <` > 31>d`e( f /10 @1/
. *1<( <>g< JF( >df /c )1/

! " 5 ; ? G M P
# / H # h H i ,
$ j $ J I V k
5 l 5 Q @ W `
; m ; 3 / \ S
? n ? * 9 ^ >
G o G + ) < &
M p M . ] = q
P r P b s B 7
R t R " : C u
U v U c O A w
J x y z { | }
Q f ~ K  
3 ! (
* X Z 
+ % 8
. 0 6 * +1!
27
Parameter Setting List

Program

Barcode standard parameter setting list


If you wish to display the current configuration of your
AS-8110/8120/8150/8250/8310/8312, scanner over the host
terminal/computer, scan the Barcode standard parameter
setting list bar code.

Unique parameter list


If you wish to display the unique parameter setting list, scan
the unique parameter list bar code

System parameter setting list


If you wish to display the product information and revision
number for your AS-8110/8120/8150/8250/8310/8312
scanner over the host terminal/computer, scan the System
parameter setting list bar code.

String setting list


If you wish to display the string
format list, scan the String setting list bar code.

28 Exit
Query present scanner firmware version

Program

Firmware version list


If you wish to display the firmware version, scan
the Firmware version list barcode.

Exit

Reset scanner to factory default settings

Program

WARNING: Default value initialization


If you wish to return the AS-8110/8120/8150/8250/8310 to
all the factory default settings, scan the Default value
initialization bar code.

29
0

A
1

B
2

C
3

D
4

E
5

F
6

8
Finish

9
30

You might also like