Old Navy Price Checker Fixture Mounted Installation Guide

Download as pdf or txt
Download as pdf or txt
You are on page 1of 11

Formatted: No underline

Old Navy Price Checkers: Formatted: Left, Space After: 0 pt, Line spacing: single

Fixture Mount at Column- Installation Guide* Formatted: No underline


Formatted: No underline
Formatted: No underline
Tools/Parts:
Drill
3/8 Cement drill bit (for drilling into the floor)
Steel drill bit (for drilling into the I-Beam)
Phillips/Flat head screwdriver
Shop Vac
3/8 Concrete anchors (qty 4 per Fixture Mount) to be used to mount the fixture to the floor
**Provided with the fixture
x 1.5 Phillips head bolt (qty 1 per Fixture Mount) to be used to mount the fixture to an I-
Beam or Cement Column
Lock washers (qty 7 per Fixture Mount)
Bolt fasteners (qty 7 per Fixture Mount)
1/8 Allen wrench (for price checker mount screws)
x 1 Hex head screws (6 qty per Fixture Mount) for price checker mount connecting to fixture
mount (to be included with the Price Checker mount)
P-Touch Label Maker
Hanger Strapping (6 piece per Fixture Mount) to be used IF the fixture doesnt rest on the solid
side of the I-Beam
Formatted: Indent: Left: 0.5", No bullets or numbering

Formatted: Font: 16 pt
*See attached sample plan for typical price checker location map.
Formatted: Normal, No bullets or numbering

Formatted: Font: 16 pt
*See attached details for additional mounting options.

Old Navy Price Checker Fixture Mount Installation Guide v.34


Fixture Mount Installation Steps:
Confirm that the proper amount of Price Checker Fixtures (either 1 or 2 per store) and Price Checkers (2
or 3 per store) are onsite. The fixtures and the actual price checkers will be shipped to the store in
separate boxes.

1) Locate the pre-determined location(s) in the store to install the Price Checker. Install the
Electrical Outlet Security cover (The security cover is only needed where the Price Checker
Fixture is being used. (The security cover is NOT required for the shroud mount
installations)for all installation options (at wall, column or booth set)..

1)2)

2)3) Plug in and power on the Price Checker unit. Connect to the store Wi-Fi. (The unit

takes about 10 minutes to power up and sync).

Old Navy Price Checker Fixture Mount Installation Guide v.34


Old Navy Price Checker Fixture Mount Installation Guide v.34
5) Using the main (tallest) frame of the fixture, stand the frame flush up against the pre-
determined installation location (I-Beam/Concrete Pillar). Using a marker, outline the 4 holes
on the ground as well as the hole(s) at the top of the frame of the fixture, against the I-
Beam/Concrete Pillar, to indicate where to drill. These holes will be used to secure the fixture
to the floor and I-Beam/Concrete Pillar.

6) Ensure there is ample room for the electrical cord to be plugged in and routed into the fixture.
The cord can be routed through the hole in the back of the frame or you can knock out the
perforated holes in the back of the fixture.

Old Navy Price Checker Fixture Mount Installation Guide v.34


7) Remove the Fixture. Using a 3/8cement drill bit, drill out the previously marked holes deep
enough in order to screw down the fixture with the supplied 3/8 cement/concrete anchors
(show below) into the floor. Also drill the hole(s) for in the I-Beam/Concrete Pillar.
Use a shop vac to ensure that dust doesnt set inside the drilled out hole.

8) Use a x 1.5 Phillips head bolt to secure the Fixture to the I-Beam/Concrete Pillar.

9) Slide the front silver piece down to the bottom of the fixture frame and it should lock in
place. Place the Price Check piece back on the fixture frame.

10) Insert the electrical cord through the provided slot. Ensure that the female portion of the
electrical cord is on the front side of the Fixture. The cord can be routed through the hole in
the back of the frame or you can knock out the perforated holes in the back of the fixture.

Old Navy Price Checker Fixture Mount Installation Guide v.34


11) Using the Bolt Fasteners/Lock washers, screw/tighten the main Fixture at the top of the
fixture. There are 2 holes at the very top of the Fixture.

12) Prior to mounting the price checker plate to the Fixture, insert the price checker power supply
into the price checker mounting plate with the electrical outlet facing UP and plug in the
power supply.

Old Navy Price Checker Fixture Mount Installation Guide v.34


13) Using the provided x 1 Hex head screws, install the Price Checker mounting plate to the
recessed portion of the Fixture to secure in place.

Ensure that the Price Checker mounting plate is installed right side up, as the battery basket is
at the BOTTOM (facing towards the fixture mount).

14) Unscrew/Remove the security screw from the mount in order to install the Price Checker.

Old Navy Price Checker Fixture Mount Installation Guide v.34


15) On the Price Checker device, insert the AC power cable into the back of the Price Checker and
coil up the excess cabling within.

16) Using a p-touch label maker, create a label with the price checker device Serial Number and
affix the label on the side of the device (Label will be used for troubleshooting purposes)

Old Navy Price Checker Fixture Mount Installation Guide v.34


17) Align the 4 screws on the back of the Price Checker with the 4 slots on the mount. Insert and
slide the price checker to the right and down to lock into place.
Ensure that ALL 4 screws are in the mount.

Old Navy Price Checker Fixture Mount Installation Guide v.34


18) Insert and tighten the security screw back into the Price Checker mount in order to secure the
Price Checker in place.
Confirm that the screw is tightened far enough (past the screw on the back of the Price
Checker) so the Price Checker cannot slide out.

Old Navy Price Checker Fixture Mount Installation Guide v.34


19) Power ON the Price Checker (allow 2-3 min to boot) and confirm that the device loads to the
below page. If the device doesnt load after 5min, reboot the device by powering off/on:

20) Test the Price Checker by scanning an item and confirm that the item description/price is
displayed. Take a picture of the below and email to the Spencer PM for validation.

Old Navy Price Checker Fixture Mount Installation Guide v.34

You might also like