INSITE 7 6 1 Product Announcement Final

We are pleased to announce the production version of INSITE 7.6.1.
This supports all new and existing Cummins engine platforms.
NEW INSITE FEATURES
Installation upgrade capability

Upgrade from INSITE 7.6.0
Greenhouse Gas (GHG) ECM Security

Greenhouse Gas - Idle Shutdown and Greenhouse Gas - Vehicle Speed Limiter are two new
ECM Security settings designed to allow OEMs to configure engine settings to meet the
requirements of the GHG Rules which allows the OEM to claim GHG emissions credits. The
OEM will program the features and lock the values with an ECM password.
These programmed parameters can only be changed when the password has been provided by
the OEM.
The Greenhouse Gas ECM passwords are controlled by the OEM and ECM Password Removal
will not function on parameters locked with Greenhouse Gas ECM Security.
New Features and Parameters
Accelerator Brake Override

This feature provides the ability to limit the accelerator when both the accelerator and brake
pedals are pressed for a period of time. This will allow the operator to move the vehicle to a
safe position when conditions such as a stuck accelerator pedal or lever occurs.
Battery Power Required Lamp

This feature informs the user when it is safe to remove power after key off. This allows all data
to be saved to the flash, perform any Key OFF tasks and for the ECM to safely shutdown. Once
the lamp goes OFF, it indicates it is safe to remove power.
Coolant Level Sensor

This feature provides the necessary parameters to interface with the Engine Coolant Level
Sensor 2.
Electric Fuel Lift Pump

This feature provides the ability to configure the Electric Fuel Lift Pump.
Fuel Level Sensor 2

This feature provides the capability to enable the Fuel Level Sensor 2.
Fuel Level Sensor 2 Multiplexing

This feature provides customers to configure the ECM to accept the Fuel Level Sensor 2 input
via the datalink instead of a physical ECM input.
Greenhouse Gas Idle Shutdown

This feature provides the ability for the OEM's to enable Idle Shutdown as well as define the
distance the vehicle must travel before Idle Shutdown can be modified. To change these
settings, the OEM must be contacted for the Greenhouse Gas - Idle Shutdown password.
Greenhouse Gas Vehicle Speed Limiter

This feature provides the ability for the OEM's to set the Maximum Vehicle Speed and driver
initiated overrides as well as define the distance the vehicle must travel before these settings
can be modified. To change these settings, the OEM must be contacted for the Greenhouse
Gas - Vehicle Speed Limiter password.
Idle Shutdown Warning Period

This feature will set up the amount of time the warning lamp will blink before the engine is
shutdown while idling.
Step Size Adjustment

This feature provides the ability to configure the amount of increase or decrease in step size
when adjusting the Power Take Off speed.
ECM Diagnostic Test
This test will be displayed by INSITE only if it is supported by the calibration.
Aftertreatment SCR Performance Test

The Aftertreatment SCR Performance test can be used to monitor the status of the
Aftertreatment SCR Catalyst Outlet NOx Sensor and the Aftertreatment SCR Catalyst. This test
also starts the Aftertreatment Diesel Particulate Filter Regeneration.
Data Monitor / Logger
New Monitors Supported:

Aftertreatment Combined Soot Load Estimate
Aftertreatment Diesel Exhaust Fluid Dosing State
Aftertreatment Diesel Exhaust Fluid Line Heater 3 Status
Aftertreatment Diesel Oxidation Catalyst Intake Temperature
Aftertreatment Diesel Particulate Filter Intake Temperature
Aftertreatment Diesel Particulate Filter Outlet Temperature
Aftertreatment Differential Pressure Soot Load Estimate
Aftertreatment Model Based Soot Load Estimate
Air Conditioner Pressure
Air Conditioner Status
Air Conditioning Pressure Sensor Voltage
Alternator Voltage
Clutch Interlock Park/Neutral Switch
Dual Valve Fuel Control Mode
ECM Key Off Time
EGR Cooler Bypass Valve Position
EGR Flow Ratio
EGR Valve Flow
EGR Valve Position Commanded
EGR Valve Position Fault
Engine Operating State
Engine Torque Mode
Failed Handshake Count
Fuel Level Sensor 2
Fuel Rail Pressure Feedback
High Speed Governor Breakpoint Speed
High Temperature Coolant Intake Temperature
High Temperature Coolant Intake Temperature Sensor Voltage
Interstage Pressure
Interstage Pressure Sensor Voltage
Low Speed Governor Reference Speed
Mass Air Flow Frequency
Oil Pressure Switch Status
Open Modular Diaphragm Valve Engine Run Time
Pressure Control Valve Current Commanded
Pressure Control Valve Current Feedback
Primary Accelerator Pedal or Lever Position
Secondary Accelerator Pedal or Lever Position
SKIM Communication Status
SKIM Handshake Timer
SKIM Key Received Count
SKIM Reset Status
SKIM Status
Stationary Pumping Mode
Throttle Differential Pressure
Throttle Differential Pressure Sensor Signal Voltage
Total Confirmed Modular Diaphragm Valve Pop-Offs
Voltage Regulator Driver Duty Cycle
Voltage Regulator Setpoint
Volume Control Current Commanded
Volume Control Current Feedback
Wastegate/VGT Actuator Position Commanded
Water In Fuel Error - Distance After Error
Water In Fuel Error - Distance During Error
Water In Fuel Error - Distance From Error Set To Error Cleared
Water In Fuel Error - Number of Errors
Water In Fuel Error - Total Distance At Last Error
Operating Systems
Supported:
o Windows 7 32-bit and 64-bit (Recommend Windows 7 32-bit)
Not supported:
o Windows XP, 32-bit and 64-bit
o Windows Vista, 32-bit and 64-bit
For more information, visit https://insite.cummins.com/insite/info/min_pc_hw_req.html.

INSITE 7 6 1 Product Announcement Final

Uploaded by

Copyright:

Available Formats

INSITE 7 6 1 Product Announcement Final

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

INSITE 7 6 1 Product Announcement Final

Uploaded by

Copyright:

Available Formats

We are pleased to announce the production version of INSITE 7.6.1.

This supports all new and existing Cummins engine platforms.

NEW INSITE FEATURES

Installation upgrade capability

Greenhouse Gas (GHG) ECM Security

New Features and Parameters

Accelerator Brake Override

Battery Power Required Lamp

Coolant Level Sensor

Electric Fuel Lift Pump

Fuel Level Sensor 2

Fuel Level Sensor 2 Multiplexing

Greenhouse Gas Idle Shutdown

Greenhouse Gas Vehicle Speed Limiter

Idle Shutdown Warning Period

Step Size Adjustment

ECM Diagnostic Test

This test will be displayed by INSITE only if it is supported by the calibration.

Aftertreatment SCR Performance Test

Data Monitor / Logger

New Monitors Supported:

For more information, visit https://insite.cummins.com/insite/info/min_pc_hw_req.html.

You might also like