"ANGLEFLEXSEAT" --- ALLOWABLE STEEL BEAM END REACTION

ExcelCalcs Link
Program Description:

"ANGLEFLEXSEAT" is a spreadsheet program written in MS-Excel for the purpose of determining the capacity
of a flexible seat angle connection and determine the allowable beam end reaction, the allowable end moment
for the purpose of end connection design and the weld capacity of the angle to a steel connection.

Program Environment: Microsoft Office Excel 2003

Creation Date: April 20th, 2010

Design References: 1. AISC Steel Construction Manual, 13th Ed.

This program is a workbook consisting of two (2) worksheets, described as follows:

Worksheet Name Description

1. Revision 1.2 (5/31/10) Limited the angle width, 'b', to prevent erroneous output and limit angle bending stress.

Program Assumptions and Limitations:

1. This program uses the database of member dimensions and section properties from the "AISC Shapes
Database", Version 13.0 (2005) as well as the AISC 13th Edition (ASD) Manual (2005).
2. The user may select a beam from W, S, M, C, and MC shapes and angles from all AISC listed shapes.
3. This program determines the appropriate minimum angle thickness from design procedures of the Handbook
of Stuctural Steel Connection Design and Detail, p. 154-156.
4. This program utilizes the procedure which a steel fabricator would typically use to determine end connection
design loads when end reaction values are not specified on the design and construction drawings by the
engineer. This procedure is based on the AISC 13th Edition (ASD) Manual (2005) Maximum Total Uniform Load
Tables on pages 3-33 to 3-95 and AISC Specification Chapter J10, pages 16.1-116 and 16.1-117.
5. The welding capacity, found in this program, is from the AISC 13th Edition (ASD) Manual (2005) Coefficients C
for Eccentrically Loaded Weld Groups (Table 8-4) and AISC Specificiations Chapter J2, pages 16.1-93 to 16.1-102.
6. This program does not check the column or angle supporting member's web or flange as there are too many
variables for connection.
7. This program contains comment boxes which contain a wide variety of information including explanations
of input or output items, equations used, data tables, etc. (Note: presence of a comment box is denoted
by a red triangle in the upper right-hand corner of a cell. Merely move the mouse pointer to the desired
cell to view the contents of that particular "comment box".)
 FLEXIBLE SEAT ANGLE REACTION ANALYSIS CALCULATIONS:
Allowable End Reaction for Connection Design
Using AISC 13th Edition Manual (ASD) and Tamboli, Akbar R. ###
Job Name: Subject: ###
Job Number: Originator: Checker: Yes
No
Input Data: ###
N+k
a N k ###
Beam Size: ef Beam Beam Size:
Beam Size = W10X22 R Beam Size =
k
Angle Size: Design Parameters:
Angle Size = L6X4X3/8 point of critical Beam Span, L =
Long Leg Vert? YES moment e Does End of Beam Bear on Support?
3/8
Beam End Bearing Length, N =
Design Parameters: t Beam Yield Stress, Fy =
Allow. End Reaction Based on U
End Rxn, R = 4.2 kips Member Properties:
Fy, Beam = 50 ksi Beam:
Fy, Angle = 36ksi w d=
Weld Alloy = E70ksi tw =
Brg Length, N+k = 3.41
in. Seat Length Section bf =
Offset, a = 0.75
in. Unstiffened Angle Seat tf =
Angle Width, b = 8.00
in. k=
Weld Size, w = 1/ 4
in. Properties: Sx =
Length of Beam, L = 12.00
ft. Angle: Beam: Zx =
L, horiz.= 4.0 in. d = 10.20 in.
L, vert. = 6.0 in. tw = 0.24 in.
Results: t = 0.375 in. bf = 5.75 in.
tf = 0.36 in.
Minimum Angle thickness: (Handbook of Structural Steel, p. 154-156) k= 0.66 in.
N= 2.75 in. N = (N+k) - k Sx = 23.20 in.^3
ef = 2.13 in. ef = a + N/2 Zx = 26.00 in.^4
e= 1.38 in. e = ef - 3/8 - t S.F. = Zs/Sx = 1.12 in.^5
= 1.67 Rwy =
treq'd = 0.31 in. treq'd = (4 R e /(Fy b / )) ^ 0.5 N/d =
Rwc =
Allowable End Reaction Based on Either Uniform Load or Web Shear: (AISC p. 33-95) R=
Fbx = 33.55 ksi Fbx = (S.F./1.67)*Fy (AISC Eqn. F2-1) Maximum Allowable End Reacti
Mr = 64.87 ft-kips Mr = (Fbx*Sx)/12 (from AISC Max. Total Uniform Load Tables p. 3-33 to 3-95) R(max) =
M1(max) = 64.87 ft-kips M1(max) = w(unif)*L^2/8 = Mr Maximum Allowable End Mome
w(unif) = 3.60 kips/ft. w(unif) = 8*(Mr)/L^2 = 8*(Fbx*Sx/12)/L^2 M2(max) =
kv = 5.00 kv = 5.0 for unstiffened webs M2(max)/M1(max) =
Cv = 1.00 Cv = 1.0 for h/tw 2.24*sqrt(E/Fy), otherwise see Eqn. G2-3 to G2-5 W36X262
Fv = 20.00 ksi Rvg = (1/1.5)*0.60*Fy*Cv Required Angle Thickness:
V = 48.96 kips V = Fv*Aw = Fv*(d*tw) (Allowable web shear) N=
W(total) = 43.25 kips W(total) = Minimum of: w(unif)*L or 2*V (AISC Table p. 3-33 to 3-95) ef =
Rv = 21.62 kips Rv = Minimum of: W(total)/2 = w(unif)*L/2 or V (based on Mr or V) e=
treq'd =
Unequal Legs?
W36X182
W36X170
(continued)
 W36X150
Allowable End Reaction Based on End Bearing Criteria for Beam: (AISC Section J10.3) W36X135
R1/ = 13.20 kips R1/ = 2.5*k*Fy*tw / ( = 1.5, Constant for web yielding - AISC page 9-18) W33X387
R2/ = 8.00 kips/in. R2/ = Fy*tw / ( = 1.5, Constant for web yielding - AISC page 9-18) W33X354
R3/ = 16.99 kips R3/ = { 0.40*tw^2*sqrt(E*Fy*tf / tw) } / W33X318
( = 2.0, Constant for web crippling - AISC page 9-18) W33X291
R4/ = 2.72 kips/in. R4/ = { 0.40*tw^2*(3/d)*(tw/tf)^1.5*sqrt(E*Fy*tf / tw) } / W33X263
( = 2.0, Constant for web crippling - AISC page 9-18) W33X241
R5/ = 15.14 kips R5/ = { 0.40*tw^2*(1-0.2*(tw/tf)^1.5)*sqrt(E*Fy*tf / tw) } / W33X221
( = 2.0, Constant for web crippling - AISC page 9-18) W33X201
R6/ = 3.63 kips/in. R6/ = { 0.40*tw^2*(4/d)*(tw/tf)^1.5*sqrt(E*Fy*tf / tw) } / W33X169
( = 2.0, Constant for web crippling - AISC page 9-18) W33X152
Rwy = 35.20 kips Rwy = R1/+N*R2/ (based on web yielding per AISC Eqn. J10-3, p. 16.1-117) W33X141
N/d = 0.27 N/d = Criteria for using either Eqn. J10-5a or J10-5b W33X130
Rwc = 25.11 kips Rwc = R5/+N*R6/ (based on web crip. per AISC Eqn. J10-5b, p. 16.1-117) W33X118
R= 25.11 kips R = Minimum of: Rwy or Rwc W30X391
W30X357
Maximum Allowable End Reaction for Connection Design: W30X326
R(max) = 21.62 kips R(max) = Minimum of: Rv or R W30X292
W30X261
Maximum Allowable End Moment for Connection Design Using Directly Welded Flanges: W30X235
M2(max) = 50.92 ft-kips M2(max) = (bf*tf)*(0.60*Fy)*(d-tf)/12 W30X211
W30X191
Maximum Allowable Weld Capacity: (AISC Table 8-4) W30X173
L= 6.00 in. L = vertical weld length W30X148
aL = 2.13 in. aL = dist. from Pv to C.G. W30X132
a= 0.35 a = (aL)/L W30X124
k= 0.00 k = 0 (for Special Case) W30X116
C1 = 1.00 Electrode Strength Coefficient, C1,Table 8-3 W30X108
C = 2.857 (interpolated from Table 8-4) W30X99
D= 4 Weld in 1/16 of inch. W30X90
= 2.0 W27X539
Rn / = 34.29 kips Rn / = C C1 D L / W27X368
W27X336
Comments: W27X307
W27X281
W27X258
W27X235
W27X217
W27X194
W27X178
W27X161
W27X146
W27X129
W27X114
W27X102
W27X94
W27X84