[Type the document title]

LITERATURE REVIEW
Priyanka Kothari. et. al. " Leaf springs are one of the oldest suspension components they are still
frequently used, especially in commercial vehicles. The literature has indicated a growing
interest in the replacement of steel spring with composite leaf spring. The suspension system in a
vehicle significantly affects the behavior of vehicle, i.e. vibration characteristics including ride
comfort, stability etc. Leaf springs are commonly used in the vehicle suspension system and are
subjected to millions of varying stress cycles leading to fatigue failure. A lot of research has been
done for improving the performance of leaf spring.

Venkatesan M. et. al. (2016), in their work design and experimental analysis of composite leaf
spring were described. This work attempted to compare the load carrying capacity, stiffness and
weight savings of composite leaf spring with that of steel leaf spring. In this work the dimensions
of leaf spring taken from existing conventional steel leaf spring of a light commercial vehicle
and the material was used for fabricating the composite one as E-glass/epoxy unidirectional
laminates. Here in this work using design data the conventional steel leaf spring was modeled
and analyzed using ANSYS 15.0 and compared with the experimental results. Modeled leaf
spring again analyzed by changing the material as composite one and compared with
experimental results. After comparing analytical and experimental results, conventional steel leaf
spring and composite leaf spring were compared with each other. From comparison it was
concluded that composite material can be use in place of steel for leaf spring and also the weight
of the leaf spring was reduced by using composite material without affecting its load carrying
capacity.

Erol Sancaktar et. al. (1999), in his work described the design and manufacture of a functional
composite leaf spring for solar powered light vehicle. The main objective of this work was to
provide and understanding of the manufacture, use and capabilities of composite leaf spring. The
material selected for the fabrication of the initial design leaves consisted of a full thickness of
unidirectional E-glass fibers with two layers of bi-directional fabric on the outer layers
embedded in a vinyl ester resin matrix. The bi-directional fabric used to prevent leaf deformation
and subsequent failure in bending about its longitudinal axis it was selected due to overall weight
reduction of the vehicle primarily considered.

This work attempted due to some failure aspect which occurs in the previous leaf spring. The
reason behind the failure was:

Cracks perpendicular to leaf longitudinal axis

The reasons discussed in this paper were sort out by giving the alternative designs by
modification of the initial leaf spring. The design offered many advantages over the initial
design. By tapering the leaves in the thickness direction as well as in the width direction towards
 [Type the document title]

the ends, an even distribution of stresses was achieved providing efficient material usage. The
low stress region at the tips of the hole, as well as the holes themselves, present in the initial
design is now eliminated. Also, the fibres have a more uniform orientation resulting in a spring,
which was easier to model analytically and manufacture. In the alternative design the material
selected as E-glass due to their high extensibility, toughness and low cost. In order to facilitate
the wetting of the fibres, epoxy resin with 2 h pot life was selected. When the comparison was
done, it was found that the redesign of the solar cars front suspension leaf springs was
successful as it met all design targets and requirements.

Mahmood M. Shokrieh et. al. (2003), in their work they focused on the objective of shape
optimization of the spring to give the minimum weight for the objective of a light commercial
vehicle. For the purpose, they considered a LCV (Light commercial vehicle) and analyzed a
conventional leaf spring used in the rear suspension system using ANSYS 15.0 software and the
results were verified with analytical and experimental solutions. The experimental results were
not sufficient to design the leaf spring. So, a stress analysis was performed using finite element
method. In this approach every leaf was modeled with eight-node 3D brick elements (SOLID 45)
and then five node 3D contact elements (CONTACT 49) were used to represent contact and
sliding between adjacent surfaces of leaves. Considering several types of vehicles that have leaf
springs and different loading on them, various kinds of composite leaf spring have been
developed. But in this study the simplified assumptions were removed and the spring was
designed using a more realistic situation. The main criterion was considered for selecting the
composite material, as the storable energy in the leaf spring. The amount of elastic energy that
can be stored by a leaf spring volume unit is given by the equation. This paper provided a graph
which clearly shows the specific strain energies of the spring materials. The given figure was
specify the percentage of strain energies for static loading and hatched region shows for dynamic
loading when the fatigue strength is used.

Form above graph (it was found that the composite material which well suited for the given
problem as Eglass/epoxy.

After selection the leaf spring again analysed by changing the material. Then comparison was
done of conventional leaf spring with the composite one. It was found that the stresses in the
composite leaf spring were much lower than that of the steel leaf spring. It was also found that
the weight of the composite leaf spring reduced about 80% than that of the steel leaf spring and
natural frequency was higher than the steel leaf spring.

Gulur Siddaramanna Shiva Shankar et. al. (2006), aim of their paper was to present a low cost
fabrication of complete mono composite leaf spring and mono leaf spring with bonded end joints
and also general study was done on the analysis and design. In this work a single leaf designed
and fabricated by hand lay-up technique and tested. The single leaf of leaf spring variable in
thickness and width and material used for the fabrication as unidirectional glass fibre reinforced
plastic (GFRP) with similar mechanical and geometrical properties to the multi leaf spring. In
 [Type the document title]

this work computer algorithm using C-language was used for the design of constant cross-section
leaf spring. For this work design constraints were stresses (Tsai-Wu failure criterion) and
displacement, a stress analysis was performed using the finite element method done using
ANSYS software. Modelling was done for every leaf with eight-node 3D brick element (solid
45) and five-node 3D contact element (contact 49) used to represent contact and sliding between
adjacent surfaces of leaves. Also, analysis carried out for composite leaf spring with bonded end
joints for Glass/Epoxy, Graphite/Epoxy and Carbon/Epoxy composite materials and the results
were compared with steel leaf spring with eye end. It was concluded that there is no objection
from strength point of view also, in the process of replacing the conventional leaf spring by
composite leaf spring. It was observed that the major disadvantage of composite leaf spring is
chipping resistance. The matrix material is likely to chip off when it is subjected to poor road
environments which may break some fibres in the lower portion of the spring. This may result in
a loss of capability to share flexural stiffness. But this depends on the condition of the road. In
normal road condition, this type of problem will not be there. It was concluded that the weight of
the composite leaf spring 85% lesser than the conventional leaf spring.

Patunkar M. M. et. al. the objective of their work was to present modeling and analysis of
composite mono leaf spring and compare its results. In this work conventional leaf spring was
tested for the static load conditions and the material of the conventional leaf spring was 60Si7
(BIS). According to the same design data a virtual model was created of a composite material
leaf spring the material E-glass/Epoxy was selected as for composite one. In this work leaf spring
was modeled in CATIA and analyzed in ANSYS 15.0. The tested results of the conventional leaf
spring were compared with the virtual model of the composite material leaf spring. For analyzing
the leaf spring finite element method was used. On the basis of comparison graphs were plotted
as shown in the it was found that the deflection of the composite leaf spring lesser than that of
the conventional leaf spring.