Scribd Logo
Upload

Welcome to Scribd!

  • 3K views

    Tabla Uw-12

    Uploaded by

    Christian Lopez Mendez
    Table Joint Efficient

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Tabla Uw-12

    Uploaded by

    Christian Lopez Mendez
    3K views1 page
    Table Joint Efficient

    Original Title

    tabla uw-12

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Table Joint Efficient

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3K views1 page

    Tabla Uw-12

    Uploaded by

    Christian Lopez Mendez
    Table Joint Efficient

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Copyrighted material licensed to University of Toronto by Thomson Scientific, Inc. (www.techstreet.com).

    15 Table UW-12
    Maximum Allowable Joint Efficiencies for Arc and Gas Welded Joints
    Degree of Radiographic
    Examination
    (a) Full (b) Spot (c)
    Type No. Joint Description Limitations Joint Category [Note (1)] [Note (2)] None
    (1) Butt joints as attained by doublewelding or by None A, B, C, and D 1.00 0.85 0.70
    other means that will obtain the same
    quality of deposited weld metal on the inside
    and outside weld surfaces to agree with the
    requirements of UW-35. Welds using metal
    backing strips that remain in place are
    excluded.
    (2) Singlewelded butt joint with backing strip (a) None except as in (b) below A, B, C, and D 0.90 0.80 0.65
    other than those included under (1) (b) Circumferential butt joints with one plate offset; see A, B, and C 0.90 0.80 0.65
    UW-13(b)(4) and Figure UW-13.1, sketch (i)
    (3) Singlewelded butt joint without use of backing Circumferential butt joints only, not over 5/8 in. (16 mm) A, B, and C NA NA 0.60
    strip thick and not over 24 in. (600 mm) outside diameter

    ASME BPVC.VIII.1-2015
    (4) Double full fillet lap joint (a) Longitudinal joints not over 3/8 in. (10 mm) thick A NA NA 0.55
    (b) Circumferential joints not over 5/8 in. (16 mm) thick B and C [Note (3)] NA NA 0.55
    (5) Single full fillet lap joints with plug welds (a) Circumferential joints [Note (4)] for attachment of B NA NA 0.50
    115

    conforming to UW-17 heads not over 24 in. (600 mm) outside diameter to
    shells not over 1/2 in. (13 mm) thick
    (b) Circumferential joints for the attachment to shells of C NA NA 0.50
    jackets not over 5/8 in. (16 mm) in nominal thickness
    where the distance from the center of the plug weld to
    the edge of the plate is not less than 11/2 times the
    diameter of the hole for the plug.
    (6) Single full fillet lap joints without plug welds (a) For the attachment of heads convex to pressure to shells A and B NA NA 0.45
    not over 5/8 in. (16 mm) required thickness, only with use
    of fillet weld on inside of shell; or
    (b) for attachment of heads having pressure on either side, A and B NA NA 0.45
    to shells not over 24 in. (600 mm) inside diameter and

    This copy downloaded on 2015-07-13 07:03:53 -0


    not over 1/4 in. (6 mm) required thickness with fillet weld
    on outside of head flange only
    (7) Corner joints, full penetration, partial As limited by Figure UW-13.2 and Figure UW-16.1 C and D NA NA NA
    penetration, and/or fillet welded [Note (5)]
    (8) Angle joints Design per U-2(g) for Category B and C joints B, C, and D NA NA NA

    GENERAL NOTE: E = 1.00 for butt joints in compression.


    NOTES:
    (1) See UW-12(a) and UW-51.

    UW-12
    (2) See UW-12(b) and UW-52.
    (3) For Type No. 4 Category C joint, limitation not applicable for bolted flange connections.

    You might also like