Scribd Logo
Upload

Welcome to Scribd!

  • 517 views

    Edc15p Recovey With Mpps

    Uploaded by

    bogdan_cornea_ro522
    The document provides step-by-step instructions for using MPPS software in bootmode to recover an EDC15 ECU that was bricked due to a bad flash. It describes removing the ECU, soldering a wire to the bootmode pin and connecting it to a 5k resistor. It also shows how to connect the MPPS cable and navigate the MPPS software to select the bootmode write function, choose the generic option, select the original ECU file, check the checksum, and write the file to recover the ECU.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Edc15p Recovey With Mpps

    Uploaded by

    bogdan_cornea_ro522
    517 views5 pages
    The document provides step-by-step instructions for using MPPS software in bootmode to recover an EDC15 ECU that was bricked due to a bad flash. It describes removing the ECU, soldering a wire to the bootmode pin and connecting it to a 5k resistor. It also shows how to connect the MPPS cable and navigate the MPPS software to select the bootmode write function, choose the generic option, select the original ECU file, check the checksum, and write the file to recover the ECU.

    Original Description:

    edc15 mpps

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides step-by-step instructions for using MPPS software in bootmode to recover an EDC15 ECU that was bricked due to a bad flash. It describes removing the ECU, soldering a wire to the bootmode pin and connecting it to a 5k resistor. It also shows how to connect the MPPS cable and navigate the MPPS software to select the bootmode write function, choose the generic option, select the original ECU file, check the checksum, and write the file to recover the ECU.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    517 views5 pages

    Edc15p Recovey With Mpps

    Uploaded by

    bogdan_cornea_ro522
    The document provides step-by-step instructions for using MPPS software in bootmode to recover an EDC15 ECU that was bricked due to a bad flash. It describes removing the ECU, soldering a wire to the bootmode pin and connecting it to a 5k resistor. It also shows how to connect the MPPS cable and navigate the MPPS software to select the bootmode write function, choose the generic option, select the original ECU file, check the checksum, and write the file to recover the ECU.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    EDC 15 Recovery using bootmode with

    MPPS V12
    Long story made short
    My friend asked if i can add some oomph to his VW TDI, so went to ebay bought
    MPPS chinese clone and got the file. I was ready to flash it, but forgot to
    checksum it. The end result... well you know the end result. If you read this then
    probably got similar problems and want to use MPPS to write the original file back
    in bootmode. Read on and maybe my experiance with this particular problem will
    help you to solve yours.

    I have searched for a solution to fix bad flashing/write disaster or error, or bricked EDC15 or
    whatever you call it, and got to the point where i found many info regarding how to enter
    bootmode, desoldering and programming with willem programmer, and found many pictures,
    wiring and so on.

    But aparently none of them described how to do this exatcly, i mean how to write with mpps in
    bootmode. Everyone was saying that is simple, jus write in bootmode, MPPS can recover
    almost any EDC15 ECU, Ive done many times an so on.

    I found this very hard to do, and while searching decided that if i succeed to recover i will do a
    simple instructions how to do it without asking too many dumb questions.

    So here it is in very short description, with pictures.

    P.S. I do not own the pictures, they are the property of their respective owners, I dont know
    who are they just found them on the mighty GOOGLE.

    You do this on your own, and i cant be responsible for mistakes you make!
    1. Remove the ECU. Warm it a little bit up, there is a sealnt which holds the housing halves pretty
    strong, so after warming will be easier to open it. Dont heat it too much, just to be hand warm.
    Here is the picture, this is what you will probably see inside the ECU case.
    2. 29F400 Location and bootmode pin 24. For now you have to solder a wire to the pin. To the
    other end of the wire conncet 5k resistor. Thats it for now. Here are the picture of the chip, and
    the pin to be used.

    3. Prepare all the connections to the ecu and MPPS cable as shown on the picture below.

    MPPS Cable Pinout:

    1. Pin16 = +12v
    2. Pins 4&5 = Ground
    3. Pin 7 = K Line
    4. When all done and checked twice, connect your MPPS cable to PC, open software and
    locate the BOOTMODE wirte function. This was tricky for me, but finally i got to this point
    and after that everything was a peace of cake. Before connectin the +12v power supply to
    the proper cable as you have seen in the pictures above. And before connecting the
    negative wire be sure to ground the bootmode pin 24 thru a 5k resistor, and remove it after
    aprox 15 seconds, but do not disconnect the ecu and MPPS power connections.

    5. Navigate to where you choose brand and choose not VW or Audi etc. but choose GENERIC. I
    found this Hardly noticable, and found only after a hint in the internet after 16 hours of
    searching.
    After that choose your ECU as stated in the List that opens after ou choose GENERIC

    6. Click Checksum Open the file that you want to checksum, the open the file that you have
    read from your car before making any mods. Above the progress bar you will see something
    written in GREEN color, and youre good to go. Then click Write, choose the file to write and
    wait fo a while for the progress bar to reach 100% and you are done, and as happy as i was
    that i have saved some $$ on buying programmers, or used ECUs, or sending to a tunner for
    a fix.

    The most important thing: If you did not undertant a thing what i am talking about or have any
    questions, just ask in the forum where you have downloaded this file, the community will help as
    much as they can to solve your problems.

    Sorry for mistakes English is my native. Enjoy, and say thanks.

    This File is posted only in two places, those guys helped me a lot , and i am very thankfull for help :

    1. http://www.ecuconnections.com/
    2. http://www.digital-kaos.co.uk/

    You might also like