Advanced Structural Analysis

Prof. Devdas Menon

Module - 2.1
Lecture - 07
Review of Basic Structural Analysis-2

Good morning to you.

(Refer Slide Time: 00:20)

This is lecture 7 in the second module on Review of Basic Structural Analysis.

1
(Refer Slide Time: 00:27)

We finished the first review where we covered statically determinate structures. Now, we
are going to look at statically indeterminate structures, as well as kinematically
indeterminate structures.

(Refer Slide Time: 00:34)

The first three lectures in this part will deal with force methods, as applied to statically
indeterminate structures; you already had an exposure to this in your earlier course. So, I
will go a little fast.

2
(Refer Slide Time: 00:51)

As mentioned earlier, we are going to refer to this book on structural analysis, part IV:
Statically Indeterminate Structures - Force Methods.

(Refer Slide Time: 00:59)

You really have not got much exposure to displacement methods, but you had some
exposure to force methods. The most popular force methods are: The methods of
consistent deformations and Theorem of least work, which you have been introduced to.
These lead to a more generalized method called flexibility matrix method, which we will
study in depth in this course.

3
There are other methods like the column analogy method, which are good for manual
use, but we are not going to cover it in this course. We will look at displacement methods
later, whereas, it is important to know the main differences between force methods and
displacement methods; they are both aimed at analyzing indeterminate structures;
completely different paths; both are very interesting.

Displacement methods are probably better suited for computer applications, but can you
tell me, what are fundamentally the main differences between force methods and
displacement methods? First, with regard to the type of indeterminacy - static
indeterminacy, which means you are talking about unknown elements in the force field;
that is part of the force methods. In displacement methods, we worry about kinematic
indeterminacy. That is one major difference. What else? So, first is the type of
indeterminacy, which you answered.

(Refer Slide Time: 02:55)

Secondly, to solve the indeterminacy, you need to apply some equations which are called
governing equations. As you know very well, in force methods, they are of the nature of
compatibility equations; in displacement methods, they will be of the nature of
equilibrium equations. You need to express the displacements in terms of forces. You
can do it in two ways: you can either use a flexibility approach where you deal with the
flexibility matrix, or you deal with the stiffness matrix. So, these are broadly the

4
fundamental differences. As I mentioned, in the first three lectures we will focus on force
methods and in the next four lectures we will focus on displacement methods.

(Refer Slide Time: 03:39)

Let us begin with something you know very well. Look at this pin jointed frame or plane
truss. What is the degree of indeterminacy - static indeterminacy?

Yes, it is 2. Would you describe this? Is it 2? Look carefully.

1, sir; it is one.

It is 1. It looks deceptive; it is 1. You can use the m plus r greater than 2 j equation. For
example, what is m? How many members are there?

5.

There are five members. How many support reactions are there? It is 4.

5 plus 4 is 9. How many joints are there?

There are 4; 4 into 2 is 8. So, the number of equations available is 8. M plus r minus 2j
will be 9 minus 8 equal to 1. This is a simple problem with one degree of static
indeterminacy.

Can you tell me, whether this kind of indeterminacy is external or internal?

5
External.

You say it is external. You could view it as external? Which reaction here is
indeterminate? Is it vertical or horizontal?

It is horizontal. So, the vertical reactions are determinate. As an off shoot of this,
remember that, if such plain frame were to undergo support settlements, let us say that
support B goes down relative to support A, would you get any forces in the structure?
You do not, because the vertical reactions do not really change; they are known; so, they
are determinate. What is indeterminate is the horizontal reaction? HA and HD. So, you are
right. You could treat horizontal reaction - one of those reactions, say, HD, as the
redundant X. When you release that reaction, you get the primary structure which is
statically determinate and it is just rigid; this is one way of approach.

Let me ask, if you can treat the same problem as internally indeterminate? Yes, that
option is also there. You could remove which member or cut which member? Anyone of
those members can be removed, not necessarily the diagonal; the diagonal is what we
normally remove. Can you remove the member to get the primary structure or should
you cut it? Some text books mention about removing members, which is fine in one
sense, but inaccurate in the other sense. You will find that, that member - if you cut it, it
will have no force; if you remove it also, it will have no force. But if you cut it and apply
the unknown redundants - a pair of equal and opposite tensile forces, as shown there,
then you are also invoking the stiffness or the flexibility of that member, which would be
missing if you remove that member all together. So, the stiffness of that member BD has
a role in governing the answer of X. So, do not remove members; you just cut them.
When you cut them, you release the member. We will examine this more carefully, later.
So, we have multiple choices of indeterminacy and it is left to you whether to treat this
problem either externally or internally indeterminate.

6
(Refer Slide Time: 07:21)

There are some other types of problems. For example, this - where the support reactions
are very well known; it is externally statically determinate. Here, the indeterminacy is
internal. If you put a cut anywhere, you will expose a shear force, an axial force and a
bending moment; you have to apply them equal and opposite, as shown here.

(Refer Slide Time: 07:45)

We covered the theorem of least work in the previous class. You are familiar with this.
The first equation, dou U star by dou Xj equal to Dj, is Castiglianos second theorem.
Usually, Dj will turn out to be 0. If it is so, you can also interpret this as a minimization

7
of the complementary strain energy in the structure. Now, the Dj that we refer here is a
displacement conjugate with Xj. If you look at the previous problem where you took the
support reaction as Xj - the horizontal reaction, then Dj would be the movement in that
support. That movement is 0 in that example. Is it not? Say, movement in the original
structure is not allowed; so, Dj is 0.

Similarly, if you have a situation as in the previous case where you have treated the bar
as redundant, what would the Dj refer to? (Refer Slide Time: 09:01) I will go back to the
previous problem. Here, what would the displacement D refer to at the redundant
location? It will be the relative distance between the cut ends of the bar.

Here, we interpret it in that sense. You apply two equal and opposite forces X, to reflect
the redundant. The conjugate displacement is basically the elongation in that bar which
will be represented by the relative movement in that bar. Since the bar is not cut,
compatibility demands that, the two ends should remain joined to each other; there is no
relative displacement between the cut ends. Actually, the bar can elongate. D is not the
elongation in the bar. It is the relative displacement between the cut ends and that is how
it is reflected in Castiglianos theorem. The interpretation of it is that, we are actually
minimizing the strain energy.

(Refer Slide Time: 10:14)

We demonstrated this with a simple problem of two span continuous beam, if you recall.
You need to carry out this integration and you will get X equal to 5 W by 8.

8
(Refer Slide Time: 10:31)

There is another way of doing the same problem. That is the method of consistent
deformation. We choose the same redundant X as the support reaction in the middle
support. Then, we release that reaction. How do we release it? It is released by removing
that support all together. So, we do a superposition of that primary structure, which is a
simply supported beam loaded with the external loading - in this case UDL, plus the
unknown redundant, now shown as a separate load case. So, we treat X as a load, but an
unknown load and our job is to find X. How do we do that? Equilibrium is not enough;
you need to invoke compatibility. What would compatibility be here? What would be
consistent? The deflection at B should be 0. So, that is what you do. You look at the
deflected shapes for a better understanding. In the picture on the left, you can see very
clearly that delta B is 0. Here, B - this deflection will be maximum; so, will it be here?
(Refer Slide Time: 11:43). But they are in equal and opposite direction and you can
calculate those values; you know those standard formulae.

What would be the deflection due to the UDL here in the middle? 5 by 384 into W into,
not L, there are 2L coming here, 2 L whole cubed by E I, which can be derived as well.
Similarly, due to concentrated load, it is X into 2 L whole cube by 48 E I. These two
should be equal and that is compatibility. When you invoke that compatibility, easily you
get the answer, X equal to 5 by 8 times W. Is it clear? This is a nice way of doing and
you will understand the meaning of consistent deformations.

9
We are going to explore these two approaches. One is an energy approach where you
minimize complementary strain energy. But mind you, the theorem of least work is
strictly applicable, only when you do not have support settlements and only when you
have Dj equal to 0. If you had support settlements, you could still invoke the energy
method, but you are basically doing method of consistent deformations; you are just
finding displacements using an energy formulation.

If you want to complete this problem, after you get the answer X equal to 5 by W 8, you
can superimpose the free bodies and you can get these two bending moment diagrams.

(Refer Slide Time: 13:15)

The first due to the load is causing sagging moment here and is causing a hogging
moment here. When you join these two, you get a diagram like this. It is very
straightforward. You can draw your shear force diagram and so on.

10
(Refer Slide Time: 13:30)

Now, let us summarize the basic concepts underlying force method. What is the first
thing you need to do in the force method? You have to identify the redundants, which
also depends on the degree of static indeterminacy. Find the degree of static
indeterminacy and choose; you have choice here. If you have n - n subscript s stands for
static indeterminacy, then, we have to choose as many redundants as the indeterminacy
demands. What do you do next? Once you have chosen the redundants, you have also
chosen the primary structure, where those values of X are 0, where you release such
constraints.

Then, on those primary structures, what should you do? You first apply the?

External loading.

External loading and then you apply the redundants one at a time, if you wish and write
down the governing compatibility equations. Wherever you have made those releases,
write down those expressions. Usually, D1, D2, D3, D4, at those redundant locations will
be 0, but there are some exceptions. Where they are 0, you have a choice of invoking the
theorem of least work, but otherwise, we have to actually calculate.

Let us say, the support settles or moves horizontally. Then Dj is equal to that movement.
Is it clear?

11
Express the equations using a flexibility format. Which equations? The compatibility
equations; you have choice here. Then, you solve these simultaneous equations and find
X1 to Xn. Once you have found X1 to Xn, you draw the free body; you have got a
statically determinate system. You can analyze it, draw the shear force diagram, draw the
bending moment diagram or find the axial forces in the case of a truss. You could do it
directly on that overall free body. Alternatively, you could find out what is happening
under the action of each of those loading systems on the primary structure and superpose
everything.

So, you find the complete force response. It satisfies the equilibrium, but more important
is that, it also satisfies compatibility.

(Refer Slide Time: 15:58)

Let us quickly look at a broad generic way of describing this method. I have given you a
piece of three span continuous beam subjected to some arbitrary loading and on top of
that we have got some support movements. Support A, which is a fixed end is shown to
rotate by a known amount, theta A; it is a rotational slip; Support C deflects by delta C.
The degree of static indeterminacy of the structure is 3. So, you have many choices of
the primary structure; which one would you prefer? Cantilever - It is the easiest to draw.
So, you remove all those three supports and you can basically identify that the reaction
there is X1, X2, X3.

12
One would imagine that those reactions will be pointing upward, but there is a good
reason to assume them to be pointing downward for calculation purpose. I will show you
the reason in a while. Then, they turn out to be negative, which is totally acceptable.

Now, this is your primary structure (Refer Slide Time: 17:10). You have released those
constraints at B, C and D; you have got a cantilever. This can deflect and the deflection
that you get at B conjugate with the chosen coordinate 1 is D1; deflection at C downward
is D2; deflection at D downward is D3. You know that the answers to D1, D2, D3. They are
not 0, not all of them are 0. What is D1? D1 is 0 in the original problem. What is D2? It is
plus delta C. Then, what is D3? It is 0. So, these are your governing compatibility to
equations. These are what the right side of those equations should look like, that is, 0,
delta C, 0.

Now, you take the primary structure and do a series of superposition. Please note that
you have two loads here. One is called direct loading; the external loads are directly
caused by those arrow marks that you see there. Some are forces and some are moments.
It is a concentrated moment shown there. You also have another kind of loading here.

What is that loading called?

[Noise] (Refer Slide Time: 18:32)

Yes, that is called indirect loading, in this case, by support settlements. These two, you
should be able to put on your primary structure.

Loading - the direct forces are pretty easy to do. You can analyze this, cant you? You
have to find the deflections D1L, D2L, D3L, the L stands for the loading - external loading.
Is it clear? At those locations 1,2,3, where the redundants operate, you must able to find
D1L, D2L, D3L. You know enough techniques of finding deflection; any method you can
use; we will use the unit load method because it will help us generate the flexibility
matrix very easily, in a generic fashion.

Then you take the same beam and now you apply support settlements. What will it look
like?

Rigid body moment.

13
It is a rigid body moment. Of the two support settlements, support movements shown in
the original figure, delta C is accounted for on the right hand side of the equation. Do
you understand? Delta C is occurring at a redundant coordinate, but theta A is not at a
redundant coordinate; it is at a non-redundant coordinate - that you apply as a load, as an
external indirect loading on the primary structure. If you will allow that cantilever beam
to rotate by theta A, it will undergo a rigid body rotation. We are assuming very small
deformations; so, sin theta and tan theta are equal to theta. So, can we write down those
additional movements at 1, 2 and 3 as shown here? (Refer Slide Time: 20:18) This is
easy to understand; theta A into L1 is movement here (Refer Slide Time: 20:21), and so
on and so forth. Can we work them out? So, you have got all the movements caused by
the external loading on the primary structure.

(Refer Slide Time: 20:33)

Now, you apply the redundants. Let us put them all together, in the beginning. You
apply X1, X2, X3 and let us see the deflections that you get at 1, 2, 3 are D1X, D2X and
D3X. Now, you are in a position to write the equations of compatibility. What would they
look like? They will look like this.

In general, you may have n locations, n displacements, n degree of static indeterminacy.

14
get in case you have indirect loading at non-redundant locations. If you have
displacements at redundant locations, they get covered on the right hand side here, not
here (Refer Slide Time: 21:35). Is it clear?

Then, we are putting together all the deflections caused by the redundants on the primary
structure. You see how your learning has progressed. You first studied force response in
statically determinate structures; then you studied displacement response in statically
determinate structures and you need that understanding to write these expressions in the
compatibility equations, because you are still dealing with a statically determinate
primary structure.

(Refer Slide Time: 22:05)

Now, you will find it convenient to apply one load at a time, according to the unit load
method. You are familiar with the definition of flexibility. I have shown here three
diagrams, three cantilever beams; they are identical beams, but I apply X1 equal to 1, X2
equal to 1, X3 equal to 1; not all at the same time, but separately.

The definition of flexibility coefficient is that, the deflection here, caused by X1 equal to
1 is called equal to f11, this is f21 and this is f31; these caused by X2 equal to 1 is f12, f22
and f32 and so on and so forth. Is it clear? So, this is a physical meaning and you will find
that these flexibility coefficients are properties of the structure; they do not depend on
any loading. How do you find these values?

15
Unit load method.

You can generate a nice formula, that is integral mj mk by EI into dx. This is unit load
method. You can do that and write it in this format (Refer Slide Time: 23:20). So, all the
deflections caused by all the redundants put together can be written like this: D1X is f11
into X1 plus f12 into X2, f1n into Xn etcetera. Similarly, for D2X, and so on. I can write that
over all set of equations. Also, I get the deflections caused by the load using the unit load
method. So, the beauty is - whatever unit bending moment diagram I drew for this and
this and this (Refer Slide Time: 23:54), come in handy when I find these deflections;
because if I want to find D1L, I need to apply a unit load here (Refer Slide Time: 24:04).
Do you understand? Bending moment diagram caused by this is called M1 and so on and
so forth. Those moment diagrams come in here.

So, you need how many diagrams?

You need one moment diagram, which I call ML, caused by the external load on the
primary structure and I need a separate diagram caused by Xj equal to 1; X1 equal to 1,
X2 equal to 1, which I call m 1, 2, 3, 4, etcetera, with the help of these diagrams. If you
want to do it manually, with area multiplication method I can get all the answers.

We will see later, in matrix methods you do not have do this manually; you write a
program which will generate everything automatically.

(Refer Slide Time: 24:49)

16
Now, I can write my compatibility equations like this. I am writing all the expressions. In
this particular problem where I have only three unknowns, I can write that equation and
then solve for X1, X2, X3 by inverting the flexibility matrix or using some elimination
method and then solving it. Once I have the solution for X, I have got the correct force
response and I can draw my bending moment and shear force diagrams on my overall
free body. Is it clear?

This is the board method; we have done this.

(Refer Slide Time: 25:26)

I will go quickly over an example which we have done earlier. This is a three span
continuous beam with a cantilever overhang. This is familiar to you; you have done this.
Here, what would be a good choice of redundants? What is the degree of indeterminacy
here?

Two.

It is two. Which two would you choose?

Last two.

You can choose any two reactions.

You would set B and C because you are most comfortable with the simply supported
beam, where the supports are wide apart. Let us do something contrary to that. Let us
17
choose the reaction at A and D as the supports. There is nothing wrong with that. Of
course, you are right; this is not a good structure to build because you will have very
large deflections at A and D, but mind you, you are not building this structure in real life.
You are building it in your mind just for the purpose of solving this problem. You can
straight away write the compatibility equations based on what we have discussed.

We have only two unknowns here. Do you agree these are the correct equations? (Refer
Slide Time: 26:44) On the right hand side, D1 and D2 are both 0, because you do not
have any support settlements in this problem. Your primary structure is 1, where you
released the supports at A and D. These are the deflections caused by the external loads.
I removed the supports at A and D and I let it deflect under the external loads - this
deflection, in this direction, matching this assumed direction of X1 is D1L and this
deflection is D2L (Refer Slide Time: 27:09). Do you know how to calculate D1L and D2L?
How would you do that? First, you have to get the bending moment diagram for this
loading. Then, you have to apply a unit load f1 equal to 1 at A and separately, f2 equal to
1 at D. Then analyze those, which is what we will do.

In the first case, you apply X1 equal to 1 and incidentally when you do that, this
deflection that you get here is f11 and the one you get here is f21 (Refer Slide Time:
27:45). You can do the same with f2 equal to 1. Now, you have to solve and get the
equation. In other words, we now need to fill up this matrix, which is the coefficient
matrix and we need to find these values and then we can find X1 and X2. That is it; the
concept is straight forward.

Now, the problem with this beam is - you have bending moment diagram, which is
made up of not only the straight lines which are easy to handle, but you also have a
parabola coming into play. It may be convenient to split it into two for the purpose of
calculation. Here, I have done that. I just took the UDL part and drew the bending
moment diagram, due to the UDL separately, which you can recognize and the rest of the
load, three consequent loads would give me a bending moment diagram like this (Refer
Slide Time: 28:42). You will notice that both the diagrams are hogging moment
diagrams because the overhangs are really making the beam hog; the deflected shape
also reflects the hogging. Now, the other one is easy to do.

18
When you apply X1 equal to 1, the bending moment diagram, that is, small m1 diagram
will look like that. When you apply X2 equal to 1, this is what the diagram will look like
(Refer Slide Time: 29:09). Let us not worry too much about the calculations. You know
how to do this, but conceptually, once you get these diagrams, you can multiply these
diagrams, the way we did in the earlier classes and get the answer.

(Refer Slide Time: 29:23)

For example, if you want D1L and D2L, you need to do that integration. These are the
answers, if you work them out. They are solved in the book. You can study it in detail.
You have done this last year; so, you are familiar with it. You can find f 11, f21, which is
equal to get f12 and f22; they are pretty straight forward. You can get these numbers and
plug them into the equations. These are very easy to solve in your calculator; you can
invert the matrix or directly solve it. You get X1 next. You notice that they come
negative. They come negative and so you interpret it as the force is acting upward.

The reason why we assume them to act downward in the first place is - you will find that
all the bending moment diagrams have the same sign, in general. So, you do not have to
worry about the sign when you multiply; then negative into negative turns out to be
positive. That is the main advantage.

19
(Refer Slide Time: 30:28)

You can draw the free body diagrams. Once you know X1 and X2, you can do this. You
can draw the shear force diagram and the bending moment diagram. This is the least
expected from a student at this stage. That means, you have learnt how to do statically
determinate structures; you have got a statically indeterminate structure; you have found
the redundants; after you found the redundants, the structure is reduced to a statically
determinate structure. You can handle any structure. We have shown a beam, but could
very well apply this to a truss.

(Refer Slide Time: 30:59)

20
Usually, it makes sense to handle support settlements as a separate analysis problem
rather than mix them along with the direct forces because you would like to know, out of
curiosity, how much effect this has, independently. Here is the same continuous beam
where you have given that the support B has settled by 5mm and the support C has
settled by 10mm. Mind you, the same flexibility coefficient which you calculated earlier
are applicable here. You do not have to do any extra work; you just have to write the
equations correctly.

We will choose same redundants. You will find that 5mm and 10mm have occurred at
the non-redundant locations. So, you have to treat it as a load. So, you take the primary
structure and you allow these moments to take place, you will find you will get a nice
straight line rigid body movement. From this movement, you can figure out what is delta
D1L and what is delta D2L. Can you work it out? What is delta D1L?

The whole beam rotates by an angle theta and the relative displacement at B and C is
5mm. So, you will find this angle is this difference (Refer Slide Time: 32:20), which is
10 minus 5 divided by the span 3.75; 10 minus 5 in millimeter has to be converted into
meter. So, it is 0.005 by 3.75. That angle, you need to use to figure out those two
movements. That is simple; you can easily do it using logic and get the two deflections
correctly with the proper sign. You will find that delta D1L turns out to be negative
whereas, delta D2L turns out to be positive. If you make a mistake here, you will get a
wrong answer. So, you have to get this correct.

After that, we have same old equations. Only thing here is instead of D1L, you write delta
D1L because this is the one caused by the loading. Suppose you have a problem in which
you have both, the external loading and this, then you add those two quantities on the left
hand side; that is it. f1, f2 is all known. Solve this equation; you get X1 and X2.

21
(Refer Slide Time: 33:28)

Then, you can draw free body, shear force diagram, bending moment diagram and
deflected shape. Conceptually, it is very straightforward.

(Refer Slide Time: 33:36)

If you take the example of a truss, here, you have a truss with how many bars? Ten bars.
Is it statically determinate or indeterminate? It is indeterminate. What is the degree of
indeterminacy? One look at that structure should tell you. First, look at external
indeterminacy; externally, you can view it as beam. It is not simply supported. So, you
got one extra redundant. If you make it simply supported, that means release the

22
horizontal reaction one external indeterminacy, and internally, you got an extra diagonal.
Can you see that?

You can choose. That is what you can do.

You can choose one of those diagonal forces as one redundant and a horizontal reaction;
may be a reaction at D as another redundant. So, your primary structure will look like
this. You made a roller support at D and you cut the bar 10 in this case. The forces, if
you want to insert them, will be X1, which is the tension in that bar 10, which you do not
know, and the horizontal reaction, we are calling it as X2. Is it clear?

Now, write down the compatibility equation. They take the same format; it is very easy
to write them down. On the right hand side, D1 and D2 are 0. When you say D1 is 0 you
are actually making a statement that the relative displacement between the cut ends is 0;
the bar should never have been cut in the first place. We are not saying that this point is
not going to move; it will move when the bar elongates or contracts. But we are saying
the relative moment is not there. So, those double arrows pointing towards each other
refer to relative movement, when you interpret from a displacement perspective.

Physically, it is a little troublesome, because if they really approach each other, they will
penetrate each other or overlap each other. That is something that you worry about in
your mind. They can separate out or they can penetrate. Is it clear? That is the meaning
of that.

You can also use the strain energy formulation and solve the same equations; they mean
the same. How do you calculate the displacements? You can use a unit load method; I
hope you are familiar with this. Apply X1 equal to 1, get those forces; apply X2 equal to
1, get those forces and so on.

23
(Refer Slide Time: 36:11)

If you do that, I have got three diagrams here. The first diagram is the structure in which
I apply only the external loads, the primary structure.

The second one, I apply X1 equal to 1 and I solve it by method of joints or by method of
sections. In the second one, I apply X2 equal to 1. When I apply X2 equal to 1, X1 is 0.
So, this bar has zero force, this bar has zero force here as well (Refer Slide Time: 36:40).
Here, this bar has a force of unit magnitude. We analyze this; we have done this last
year, so I am going fast over it. It will be nice to write it in a tabular format. Write down
the ten bars, note their lengths and write down the flexibility which is L by EA. So, the
length of each bar is known; the EA values are given to you; analyze those three trusses
and write them down.

If you take this particular case, it is so easy. There are only three bars. When you pull A
horizontally, you will have an axial tension in these three bars and you do not have any
force in any other bar. That is why this is just 1 1 1 and all the others are 0. Is it clear?
These things should not take you too much time.

24
(Refer Slide Time: 37:38)

Once you have you done this exercise, invoke your unit load method equations. Are you
clear about this? We have done this before. So, get those numbers in terms of VA and
VA gets eliminated. Substitute in your compatibility equations and solve for X1 and X2.
Final bar forces are given; you can do superposition. You have already solved. In that
table, you have got forces; you have got force called by external loading. You have got
force called by X1 equal to 1. Take that column, multiply by X1; take the next column,
multiply by X2 and add up everything to get the answers.

(Refer Slide Time: 38:16)

25
It is interesting to note that some of those bar forces will be positive and some will be
negative; you must be able to judge correctly. For example, in that particular loading,
you would expect the bottom chord to be in tension and the top chords to be in
compression, in the verticals and diagonals appropriately. You should figure it out.

Let us take a displacement loading problem. Let us say, you have a lack of fit problem,
bar 10 is too long by 3 mm. When it came to the side, that bar was too long; so it had to
be force fitted; that means, it had to be hammered into place. Because the structure is
over rigid, all the other bars will resist this fixing. Had it been just rigid, they will move
and accommodate this movement. You have a problem. You are forcing that bar to be
fitted. First of all, can you tell me what will be the force in that bar? It will be
compression, because it was too long and it will not be allowed to get that length of 3
mm; the final excess length may be 2 mm or 1 mm. It depends on the relative stiffness of
all those bars. Because of this, the other bars will also be stressed. So, you have a self-
equilibrating system.

How do you solve this problem? (Refer Slide Time: 39:49) Let us take the same
redundants, as we have identified earlier. Now, the compatibility equation will look like
this. Is it clear? This is because now you have a displacement loading.

How will you get delta D1L and delta D2L? This is not as easy as the previous problem
where you had the rigid body movement in your beam.

How will you find this out? What is delta D1L and delta D2L? What does this physically
mean? In which structure?

In the primary structure. If you take the primary structure where you have the roller
support at D and the bar 10 is cut and when you allow this bar 10 to be too long by 3
mm, will you have any forces in the system? No, because it is just rigid and is statically
determinate. You will have no forces.

Can you write down delta D1L and delta D2L? What will delta D1L be? It will be 3 mm; it
is free to take whatever length you want it to take.

Will it be plus 3 mm or minus 3 mm?

It will be plus 3 millimeter. It is too long; so, it will be plus 3 mm.

26
What is delta D2L? Delta D2L is 0. Now, this 3 mm, you should write in consistent units.
So, it is 0.003 meters. If it is too long, you should visualize this as overlap of those two
bars by 3 mm. Is it clear?

That is all you have to do. You have already got the flexibility matrix in the previous
example. So, you just have to plug in these values.

Sir, why are we not taking D1 as 3 mm?

This is a good question. What is D1? D1 is the final displacement in the original real
structure, not the primary structure. When you identified X1 as the axial force in that
member and the primary structure was a structure in which you cut that member, D1 is
nothing but the relative displacement between the cut ends.

What is the relative displacement between the cut ends? It is 0. These are the typical
mistakes that students make. I want absolute clarity in understanding here. D1 is always
0, because it is the relative displacement between the cut ends. You had no business to
cut that bar. 3 mm is the elongation in that bar in a statically determinate system, which
is the relative distance between the cut ends in the primary structure. When we are
talking about the primary structure, you not talking about the right hand side, you talking
about the left hand side; because all these quantities on this side of the compatibility
equations, that is, all these values relate to primary structure. Is it clear? This is a
common mistake we tend to make.

D2 is always 0, so you do not have to worry. Is it not easy to solve? You already got the
flexibility matrix, you inverted it earlier and so it is very easy to solve and get X1 and X2.

Once you are familiar with the truss and its flexibility matrix, you can handle any
loading; you put 100 loads, you get hundred answers just by solving this matrix.

27
(Refer Slide Time: 43:57)

Once you have the solution, you can do superposition, you can get the forces and what is
interesting is that you must check the answer. The bar 10 you suspected would be in
compression and it does turn out to have a negative value here. So, it makes sense. If it
goes into tension, then you made a big mistake. You must have these checks included.

(Refer Slide Time: 44:17)

One last problem in continuation with previous one is as follows: Supposing you have
temperature loading. I now take three arbitrary bars, 1, 2 and 3 are subject to a
temperature increase of 40 degree Celsius and the coefficient of thermal expansion given

28
to you. How would you deal with the same problem? This is your problem; you can
remove 40 kilonewton. How would you analyze this problem? You have to figure out in
the primary structure what you agree that your right hand side, D1 and D2 are 0. How
will you get delta D1L and delta D2L?

Zero (Refer Slide Time: 45:10)

Why do you say Delta D2L is zero?

It doesnt move

You are right. It does not move. It does not move, for what reason?

How do you get delta D1L? Let us say, we do not make any guess, we do it the hard way.
How do you get delta D1L then? The difference between this problem and the previous
problem was that, in the previous problem, you had a movement in the redundant
coordinate. In this one, you have movement in non-redundant location, like bars 1, 2 and
3 are not at the coordinates 1 and 2. So, in your primary structure, which is one with the
roller support and with the bar 10 cut, if I heat bars 1, 2 and 3, can you tell me what those
movements are? How do you find them out? You can go for the unit load method, Is it
not? If you want to find delta D1L, what should you do? You apply f1 equals to 1.You do
that, but first in your primary structure, if bars 1, 2 and 3 elongates, you had to find those
elongations. Those are nothing but L alpha into delta T. That is a straight forward
calculation. If your alpha is this and your delta T is 40 degrees and your L is this (Refer
Slide Time: 46:42), you can figure out what are E1L, E2L and E3L. That is straight
forward.

Then, what do you do? You invoke the unit load method, which is in this equation, you
apply f1 equal to 1 or X1 equal to 1 and you look at this displacement field, where you
have these temperature changes. You have these known bar elongations; you have a pure
geometry problem and you are applying a unit load invoking the virtual work method to
solve for one unknown in that displacement field. We have done this in earlier class.

Can you find this out easily? You can do that; you have all the answers, you have the
forces caused by X1 equal to 1 and the forces caused by X2 equal to 1. You will find that
delta D1L; in this case, it is easy to work it out. Delta D1L you can solve and you can sum

29
up. You will find that only these three bar forces you need to worry about because all the
other forces are 0. You have three bar forces; you can multiply them and get the answer.
The answer would turn out to be equal to 0.6. This is easy to work out. You get delta
D1L. Delta D2L, as you guessed correctly, will turn out to be 0, for the simple reason that
when you pull here, only these three bars get a unit force and these bars do not have any
force (Refer Slide Time: 43:25). So, you are multiplying a non-zero quantity, which is
your bar elongation, with a zero quantity. We can guess this or calculate it. This is how
you deal with non-redundant displacements.

(Refer Slide Time: 48:43)

We are trying to tackle conceptually, different types of problems. You can substitute
these values, get your unknown forces, do your superposition and here bar 10 turns out to
be compression.

30
(Refer Slide Time: 48:55)

Let us look at one more example of a frame. We have a portal frame. You have done this
earlier. What is the degree of indeterminacy? Normally it is three, but there is a
symmetry in the frame. Can you reduce it? You are right. You can reduce by 1. For
example, what do you know for sure? Vertical reaction is statically determinate; you
should be never been thinking of indeterminacy for the vertical reactions. This will be
the deflected shape; there is symmetry in the deflected shape because the structure is
symmetric, the loading is symmetric. The vertical reactions are total load, that is, 200
kilo newton plus 50 into 3, that is 350.

50 into 6. You are right. 500 divided by 2 is 250.

Vertical reactions are determinate, but the horizontal reactions are not; your moments are
not, but they are equal and opposite. So, you have only two unknowns. You could do
this. If you do this, you will have to release all those moments. That means, you must
allow for a relative movement along X1 and relative rotation along X2, which means you
must replace those fixed ends with roller supports. Is it clear? Because it is all symmetric
movement, the total horizontal movement, which is D2 will be divided by 2. So, it is D2L
by 2, D2L by 2 and this rotation here is D1L by 2. Is it clear?

This is one way of doing it, but you can also cut it in the middle at C. The appropriate
boundary condition would be a guided roller support. Why? Because it is free to deflect
there, there is no shear transfer possible there. When you cut it into two, the constant

31
load, 200 kilonewton should also get cut into two. 100 kilonewton comes on the left side
frame and 100 kilonewton comes on the right hand side frame. Here, clearly there are
only two unknowns. You can make it a cantilever. There is another way of doing it.
Whichever way you do, these will be the compatibility equations.

(Refer Slide Time: 51:30)

Let us take the first way. Can you find those moments? Well, draw the bending moment
diagram, capital ML diagram. The constant load gives you a triangular moment; the UDL
gives you parabola; this is your small m1 diagram, when you apply X1 equal to 1; this is
m2 diagram, when you apply X2 equal to 1. You do not even need to mark those
deflections; they are just to help you understand; you can blindly go ahead and calculate
D1L, D2L, f11, f22, f12. Once you have unit load, it is pretty easy to calculate. We have done
this earlier. So, the method is straightforward.

32
(Refer Slide Time: 52:18)

Write down the compatibility equations; solve for X1 and X2; draw your free bodies,
draw the axial force diagram, the shear force diagram and bending moment diagram.

We will later do the same problem by displacement method. So, I will show you that it is
much easier; you can actually do it in a couple of minutes and get the bending moment
diagram directly; this is what the deflected shape looks like. So, we will stop here and
take this up in the next class.

Thank you.

33
KEYWORDS

Indeterminate

Force Method

Flexibility matrix

Compatability

Unit load method

34