2X 1 5

C e nt r e d e f o rm a ti o n d e t y p e a v i on
A318/A319/A320/A321 (CFM56)
GENERAL FAMILIARIZATION COURSE
ATA 70-36-21-30-00-05 - TOME 5/5
(PART 2 OUT OF 2)
DF.ER : N 2X 1 5
EDITION : 03/07
VALID PAR : J.-M. HAIN
Ce document est destin linstruction et ne saurait tre considr comme un document technique de rfrence. Il ne sera pas mis jour.
Reproduction mme partielle INTERDITE sans autorisation de la Socit AIR FRANCE.
Socit Air France 2000

This document must be used for training purposes only
Under no circumstances should this document be used as a reference
It will not be updated.
All rights reserved

No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,
without the prior written permission of AIRBUS S.A.S.
SINGLE AISLE TECHNICAL TRAINING MANUAL
PART 2 OUT OF 2
TOME 4/5
52 Doors Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
25 Equipment/Furnishings Presentation . . . . . . . . . . . . . . . . . . . . . . . 36
35 Oxygen Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
38 Water and Waste Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
28 Fuel System Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
26 Fire Protection Systems Presentation . . . . . . . . . . . . . . . . . . . . . 150
49 APU Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
TOME 5/5
70 Power Plant CFM56 Presentation . . . . . . . . . . . . . . . . . . . . . . . . 212
36 Pneumatic System Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . 258
21 Air Conditioning System Presentation . . . . . . . . . . . . . . . . . . . . 276
21 Ventilation System Presentation . . . . . . . . . . . . . . . . . . . . . . . . . 300
21 Cargo Ventilation & Heating SYS Presentation . . . . . . . . . . . . . 316
21 Pressurization System Presentation . . . . . . . . . . . . . . . . . . . . . . . 330
30 Ice and Rain Protection Systems Presentation . . . . . . . . . . . . . . 342
00 Documentation Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
05 Time Limits and Maintenance Checks . . . . . . . . . . . . . . . . . . . . 420
U3T06191 - U02T4M0
GENERAL FAMILIARIZATION COURSE (CFM56) TABLE OF CONTENTS May 11, 2006

PART 2 OUT OF 2 Page 1
70 POWER PLANT CFM56 PRESENTATION

INTRODUCTION
The CFM56-5B engine is a dual-rotor, variable stator, high bypass ratio
turbo fan power plant. The CFM56-5B powers the complete single aisle
family of aircraft. CFM56-5B engines are available in several thrust
ratings.
All the engines are basically the same. A programming plug on the
Electronic Control Unit (ECU) changes the available thrust.
U3T06191 - U02T4M0 - UM70PZ000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 70 POWER PLANT CFM56 PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM70PZ000000001
INTRODUCTION

INSTALLATION
The power plant installation includes the engine, the engine inlet, the
exhaust, the fan cowls and the reverser assemblies. The pylon connects
the engine to the wing structure. The engine is attached to the pylon by
forward and aft mounts.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
INSTALLATION

MODULAR CONCEPT
The CFM56-5B is designed using a modular concept. For easy
maintenance and quicker return-to-service, the engine is made of 4
primary modules:
- fan and Low Pressure (LP) compressor,
- High Pressure (HP) compressor, combustion chamber and HP turbine,
- LP turbine and Turbine Rear Frame (TRF),
- transfer and accessory gearboxes.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
MODULAR CONCEPT

MODULAR CONCEPT (continued)
LP ROTOR
The Low Pressure (LP) rotor has the forward fan, the booster
compressor and the LP shaft, all driven by the LP turbine. The speed
of the LP rotor is indicated on ECAM as N1.
The forward fan supplies most of the engine thrust. The air produced
by the fan is known as secondary airflow or bypass airflow. The
4-stage booster compressor supplies air to the engine core. This is
primary airflow. The fan and LP compressor are supported by the fan
frame which is also the location for the forward engine mount.
The 4-stage LP turbine drives the forward fan and the booster
compressor. It is supported by the TRF which is also the location for
the rear engine mount.
The LP rotor is supported by roller and ball bearings which are
lubricated and cooled.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
MODULAR CONCEPT - LP ROTOR

HP ROTOR AND COMBUSTION CHAMBER
The High Pressure (HP) rotor is made up of a 9-stage HP compressor
driven by a single-stage HP turbine. The speed of the HP rotor is
indicated on the ECAM as N2.
The HP compressor is also the source of customer bleed air.
The HP rotor is supported by roller and ball bearings, which are
lubricated and cooled.
The annular combustion chamber is located between the HP
compressor and HP turbine. It is equipped with ports for 20 fuel
nozzles and 2 igniter plugs.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
MODULAR CONCEPT - HP ROTOR AND COMBUSTION CHAMBER

TRANSFER & ACCESSORY GEARBOXES
The accessory gearbox is located at the bottom of the fan case and is
driven by the HP rotor through the transfer gearbox.
The fuel pumps, oil pumps, hydraulic pump, Integrated Drive
Generator and FADEC alternator are all driven by the gearbox.
During engine starting, the starter rotates the HP compressor through
the gearboxes.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
MODULAR CONCEPT - TRANSFER & ACCESSORY GEARBOXES

FADEC
In order to increase engine reliability and efficiency, the Full Authority
Digital Engine Control (FADEC) gives the full range of engine control
to achieve steady state and transient engine performances when operated
in combination with aircraft subsystems.
Each engine is controlled by an ECU, a dual channel computer located
on the engine fan case. The ECU controls the engine during start and all
operations. The ECU manages engine thrust and protects against
overspeed and overtemperature by controlling the engine sub-systems.
The ECU also monitors all engine subsystems and sensors for failure.
When the engine is running, power for FADEC operation is supplied by
a dual-output FADEC alternator driven by the gearbox.
The FADEC system has a dual channel ECU and the following
peripherals:
- hydromechanical unit,
- dedicated FADEC alternator,
- compressor control systems,
- clearance control systems,
- start system (starter shutoff valve, ignition exciters),
- thrust reverser system,
- oil/fuel temperature control system,
U3T06191 - U02T4M0 - UM70PZ000000001
- fuel return valve,

- engine sensors,
- electrical harnesses.
U3T06191 - U02T4M0 - UM70PZ000000001
FADEC

EIU/EVMU
The ECU interfaces with various aircraft systems. Essential
communication with the ECU (thrust lever position, air data, etc.) is direct
to and from the applicable systems and controls. Non-essential
communication (autothrust, Centralized Fault and Display Unit (CFDS),
etc) is routed through the Engine Interface Unit (EIU) of each engine.
The EIUs interface with various aircraft circuits and systems. The data
is then transmitted in a single stream to each ECU channel.
Engine vibration monitoring is accomplished by the Engine Vibration
Monitoring Unit (EVMU). The EVMU collects vibration data from both
engines. The vibration information is displayed on the ECAM and is also
available through the CFDS for troubleshooting.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
EIU/EVMU

THRUST REVERSER SYSTEM
The flight crew manually selects reverse by lifting the latching levers on
the throttle control levers. The reverse thrust command is sent to the ECU
and the Engine Interface Unit (EIU).. The signal from the ECU to the
directional valve is fed to an inhibition relay controlled by the Engine
Interface Unit (EIU) according to throttle control lever position.
According to commands from the ECU and the EIU, a Hydraulic Control
Unit (HCU) supplies hydraulic power to operate the thrust reverser. The
thrust reverser uses 4 hydraulically actuated pivoting blocker doors to
redirect the engine fan airflow.
Reverse thrust is only available on the ground.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
This Page Intentionally Left Blank

U3T06191 - U02T4M0 - UM70PZ000000001

CONTROL AND INDICATING
This section will highlight the control panels and indications for the
engines.
CONTROL PANELS
The engines are controlled by throttle control levers which are located
on the center pedestal. They can only be moved manually.
For reverse thrust operation, two latching levers let the throttle control
levers move rearward into the reverse thrust section.
The A320 family aircraft normally operate in autothrust mode in flight.
The autothrust can be disconnected by using the two instinctive
disconnect pushbuttons. These 2 red buttons are located on the outside
of each throttle control lever. This lets the engines be controlled in
manual thrust mode.
The controls for engine starting and shut down are located on the
center pedestal just behind the throttle control levers.
The engine MAN START switches are located on the overhead panel.
These switches are used to initiate an engine manual start procedure.
They are also used to initiate an engine dry or wet motoring procedure.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
CONTROL AND INDICATING - CONTROL PANELS

CONTROL AND INDICATING (continued)
ECAM ENGINE
The engine primary parameters are permanently displayed on the
upper ECAM.
The engine secondary parameters are presented on the lower ECAM
ENGINE page when selected or displayed automatically during a
fault.
Some engine parameters are permanently displayed on the CRUISE
page in flight.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
CONTROL AND INDICATING - ECAM ENGINE

ECAM ENGINE (ENHANCED)
On the enhanced system, the same information is provided with a
different display presentation.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
CONTROL AND INDICATING - ECAM ENGINE (ENHANCED)

COMPONENT LOCATION
The engine system components are at the following locations.
FADEC
The ECU is located on the RH side of the fan case. The FADEC
alternator is located on the gearbox.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - FADEC

COMPONENT LOCATION (continued)
STARTING
Two ignition boxes are located on the RH side of the engine core and
the air starter is located on the RH side of the gearbox rear face.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - STARTING

FUEL
The main components of the fuel system are located on the LH side
of the fan compartment.
The fuel pump is driven by the gearbox. The Hydromechanical Unit
(HMU) and the filter are installed with the pump.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - FUEL

AIR
The compressor airflow control, turbine clearance control, and transient
bleed and cooling systems are shown.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - AIR

OIL
The oil tank is located on the LH side of the fan case.
The lubrication unit is driven by the gearbox.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - OIL

THRUST REVERSER
The hydraulic shut-off valve is located in the forward part of the pylon.
The HCU is mounted on the front of the RH side of the 'C' duct.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
COMPONENT LOCATION - THRUST REVERSER

MAINTENANCE/TEST FACILITIES
On the maintenance panel, the ENG FADEC GND PWR is used to supply
the FADEC system for maintenance purposes, when the engines are not
running.
The MCDU is used to do tests and for trouble shooting monitored
components (computers, sensors, actuators).
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001

SAFETY PRECAUTIONS
When you work on aircraft, make sure that you obey all the Aircraft
Maintenance Manual (AMM) safety procedures.
This will prevent injury to persons and/or damage to the aircraft. Here is
an overview of main safety precautions related to the engines.
Make sure that all engine danger areas are as clear as possible to prevent
damage to the engine, the aircraft or persons in the area.
Make sure that you have fire fighting equipment available.
Do not try to stop the fan from turning by hand.
After engine shutdown, let the oil tank pressure bleed off for a minimum
of 5 minutes before you remove the tank filler cap. If you do not,
pressurized oil can flow out of the tank and cause dangerous burns.
The engine ignition system is an electrical system with high energy. You
must be careful to prevent electrical shock. Injury or death can occur to
you. Do not do maintenance on the ignition system while operating the
engine.
Make sure that the engine shutdown occurred for a minimum of 5 minutes
before you proceed.
Make sure that the thrust reverser is deactivated during maintenance. If
not, the thrust reverser can operate accidentally and cause injury to
personnel and/or damage to the reverser.
U3T06191 - U02T4M0 - UM70PZ000000001
When opening the engine cowls:

- respect the wind limitations and the opening/closing sequence,
- always secure cowls with the hold-open rods,
- make sure that the slats are retracted and install a warning notice to
prevent slat operation.
U3T06191 - U02T4M0 - UM70PZ000000001
SAFETY PRECAUTIONS

LUBRICANTS AND FUELS
The list of the materials required for the aircraft service and maintenance
can be found in the AMM, Chapter 20 STANDARD PRACTICES or
Chapter 70 STANDARD PRACTICES for the engines.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
LUBRICANTS AND FUELS

STORAGE AND PRESERVATION
Storage and preservation procedures must be applied to engines which
are not operated for more than 30 days. The preservation procedures
protect the engine against corrosion, liquid and debris entering the engine,
and atmospheric conditions during period of inactivity.
CAUTION: Under no circumstances shall preservative oil or equivalent

be sprayed into the engine inlet, core compressor or turbine,
or engine exhaust. Dirt particles deposited on the wet blades
and vanes may adversely affect engine performance during
subsequent operation.
U3T06191 - U02T4M0 - UM70PZ000000001
U3T06191 - U02T4M0 - UM70PZ000000001
STORAGE AND PRESERVATION
36 PNEUMATIC SYSTEM PRESENTATION

SYSTEM INTRODUCTION
The Airbus single aisle family pneumatic system supplies High Pressure
(HP) air for:
- air conditioning,
- wing ice protection,
- water pressurization,
- hydraulic reservoir pressurization,
- engine starting.
High Pressure air can be supplied from three sources:
- the engine bleed system,
- the APU,
- a HP ground power unit.
The pneumatic system operates pneumatically and is monitored by 2
Bleed Monitoring Computers (BMC 1 & 2).
There is one BMC for each engine bleed system.
Both BMCs exchange data. If one BMC fails, the other BMC takes over
most of its monitoring functions.
U3T06191 - U02T4M0 - UM36PZ000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 36 PNEUMATIC SYSTEM PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM36PZ000000001
SYSTEM INTRODUCTION

SYSTEM INTRODUCTION (continued)
ENGINE BLEED
The engine bleed air is pressure and temperature regulated prior to
supplying the pneumatic system. Air is bled from two engine High
Pressure Compressor (HPC) stages, the Intermediate Pressure (IP)
stage and the HP stage.
The HP bleed is only used when the engines are at low power. Once
the IP bleed is sufficient, the HP valve closes.
All the engine bleed air is supplied to the pneumatic system through
the main engine BLEED valve (or Pressure Regulating Valve (PRV))
which acts as a shut off and overall system pressure regulating valve.
Each BMC monitors system pressure and will shut down the engine
bleed in case of excessive pressure. In addition, an Overpressure Valve
(OPV) is installed downstream from the bleed valve to protect the
system in case of overpressure.
The temperature of the engine bleed air is regulated to a maximum
value. The hot bleed air goes through an air-to-air heat exchanger
called the precooler. Fan discharge air modulated by the Fan Air Valve
(FAV), blows across the pre-cooler to maintain the temperature within
limits.
U3T06191 - U02T4M0 - UM36PZ000000001
APU BLEED/EXTERNAL AIR

The left and right bleed systems are connected by a crossbleed duct.
A crossbleed valve enables their interconnection or isolation.
The APU can also be used for bleed air supply. This is usually done
on the ground for air conditioning and for engine start.
However, APU BLEED air could also be used in flight, depending
on altitude. The APU bleed supply is connected to the left side of the
crossbleed duct.
On the ground, a HP ground power unit can be connected to the left
side pneumatic system. The right side may be supplied by opening
the crossbleed valve.
U3T06191 - U02T4M0 - UM36PZ000000001
SYSTEM INTRODUCTION - ENGINE BLEED & APU BLEED/EXTERNAL AIR

SYSTEM INTRODUCTION (continued)
LEAK DETECTION
Leak detection loops are installed along the hot air supply ducts of
the pneumatic system. The loops are made of multiple sensing
elements connected in series. The leak detection loops are connected
to the BMCs. If a leak is detected, a signal is sent to the BMC 1 or 2
which automatically isolates the affected area by closing the crossbleed
valve and shutting off the engine bleed on the affected side. The leak
detection system is organized into three loops. Here are the loops and
the protected areas: - pylon: from the precooler to the wing leading
edge,
- wing: wing leading edge including the wing air inlet supply, and
belly fairing (cross bleed duct, pack supply ducts and APU forward
supply duct).
- APU: APU aft supply duct (left hand side of the fuselage) from APU
firewall to wheel well area.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
SYSTEM INTRODUCTION - LEAK DETECTION

CONTROL & INDICATING
This section highlights the control panels and indications for the
pneumatic system.
CONTROL PANEL
Controls for the pneumatic system are part of the AIR COND panel,
located on the overhead panel.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
CONTROL & INDICATING - CONTROL PANEL

CONTROL & INDICATING (continued)
ECAM INDICATION
The pneumatic system indications are displayed on the lower part of
the ECAM BLEED page.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
CONTROL & INDICATING - ECAM INDICATION

COMPONENT LOCATION
The main components of the fuel system are located on the engines and
in the pylons.
PRESSURE REGULATION COMPONENTS
The pressure regulation components are located on the engines:
- the Engine High Pressure Valve (HPV),
- the Engine BLEED PRV,
- the OPV.
TEMPERATURE REGULATION COMPONENTS
The temperature regulation components are located on the engines
and in the pylons:
- the FAV,
- the Precooler.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
COMPONENT LOCATION - PRESSURE REGULATION COMPONENTS & TEMPERATURE REGULATION COMPONENTS

OTHER COMPONENTS
The crossbleed valve is located in the forward section of the lower
fuselage belly fairing area.
Get access to the HP ground connector through a small access door
located on the lower fuselage belly fairing.
The APU bleed valve is located on the APU.
The APU supply duct runs along the left hand side of the fuselage to
the wheel well area. It then crosses at the aircraft centerline and
continues forward to be connected to the crossbleed duct in the forward
belly fairing area.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
COMPONENT LOCATION - OTHER COMPONENTS

Using the Multipurpose Control and Display Unit (MCDU), you can
have access to the Centralized Fault Display System (CFDS) fault
messages of the PNEUMATIC system. Specific BMC Built-In Test
Equipment (BITE) is also available for BMC 1 and 2.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001

SAFETY PRECAUTIONS
When you work on aircraft, make sure that you obey all the Aircraft
Maintenance Manual (AMM) safety procedures. This will prevent injury
to people and / or damage to the aircraft. Here is an overview of the main
safety precautions related to the pneumatic system.
Make sure that the pneumatic system is depressurized before starting the
work. HP air can cause unwanted pressurization of the aircraft, and injury
to personnel.
Be careful when you work on the engine components immediately after
the engine is shutdown. The engine components can stay hot for up to
one hour.
U3T06191 - U02T4M0 - UM36PZ000000001
U3T06191 - U02T4M0 - UM36PZ000000001
SAFETY PRECAUTIONS
21 AIR CONDITIONING SYSTEM PRESENTATION

AIR CONDITIONING, VENTILATION AND
PRESSURIZATION INTRODUCTION
This chapter covers the air conditioning, ventilation and pressurization
systems.
The basic airflow through the pressurized part of the fuselage starts with
the pneumatic system.
Hot, high pressure air is supplied to two packs. The packs are responsible
for basic temperature regulation.
From the packs the air is distributed throughout the aircraft.
The pressurization system controls the airflow overboard to maintain the
cabin pressurization within safe limits.
U3T06191 - U02T4M0 - UM21PZ000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 21 AIR CONDITIONING SYSTEM PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM21PZ000000001
AIR CONDITIONING, VENTILATION AND PRESSURIZATION INTRODUCTION

BASIC AIR CONDITIONING SYSTEM INTRODUCTION
The pneumatic system supplies air to each pack. The packs are responsible
for BASIC temperature regulation.
Temperature regulated pack discharge air is sent to the mixer unit.
At the mixer unit, the air is mixed with air re-circulated from the main
cabin. This reduces the overall bleed demand and saves fuel.
From the mixer, the air is distributed to the cockpit and the forward and
aft cabin zones.
Some of the air from the pneumatic system is used for the OPTIMIZED
temperature regulation system. This hot air is mixed with the air from
the mixer to adjust the temperature in each zone independently.
The air is distributed throughout the cabin and finally, discharged
overboard through the outflow valve to maintain pressurization.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
BASIC AIR CONDITIONING SYSTEM INTRODUCTION

PACK INTRODUCTION
The Single Aisle family is equipped with two air conditioning packs
located in the wing root area forward of the landing gear bay. The packs
supply dry air to the cabin for air conditioning, ventilation and
pressurization.
The main component of each pack assembly is the Air Cycle Machine.
Hot air from the pneumatic system is supplied to the pack through the
pack Flow Control Valve (FCV). The FCV adjusts the flow rate through
the pack and is the pack shut-off valve.
The pack temperature control system controls the pack outlet temperature
and sets its maximum and minimum limits. The system includes two
Pack Controllers (PCs). Each PC controls one pack and has two
computers, one primary and one electrically independent secondary
computer. When the primary computer is operational, the system is fully
functional. If the primary fails, some functions are lost as the secondary
computer takes control.
During normal operation, the Zone Controller (ZC) sends the required
pack outlet temperature to both PCs. To control the pack outlet
temperature, the PC modulates the BYPASS VALVE and the RAM-AIR
INLET doors. For maximum cooling, the ram-air doors are fully open
and the bypass valve is fully closed. For maximum heating, the ram-air
U3T06191 - U02T4M0 - UM21PZ000000001
doors are nearly closed and the bypass valve is fully open. During takeoff
and landing, the ram air inlet doors will be driven fully closed to stop the
ingestion of foreign matter.
U3T06191 - U02T4M0 - UM21PZ000000001
PACK INTRODUCTION

PACK INTRODUCTION (continued)
ENHANCED
The ZCs and PCs are replaced by two Air Conditioning System
Controllers (ACSC) 1 and 2. ACSC 1 sends the pack outlet
temperature demand to pack 1. Air Conditioning System Controller
2 sends the pack outlet temperature demand to pack 2. To control the
pack outlet temperature, the Air Conditioning System Controller
modulates the BYPASS VALVE and the RAM-AIR INLET doors.
For maximum cooling, the ram-air doors are fully open and the bypass
valve is fully closed. For maximum heating, the ram-air doors are
nearly closed and the bypass valve is fully open. During takeoff and
landing, the ram air inlet doors will be driven fully closed to stop the
ingestion of foreign matter.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
PACK INTRODUCTION - ENHANCED

ZONE TEMPERATURE REGULATION SYSTEM
INTRODUCTION
The packs supply the mixer unit. Three separate aircraft zones are supplied
from the mixer unit:
- cockpit,
- forward cabin,
- aft cabin.
Two cabin recirculation fans are installed to reduce the bleed air demand
and therefore save fuel. These fans establish a recirculation flow of air
from the cabin zones to the mixer unit. In normal operation, there are no
ECAM indications associated with the cabin fans.
The ZC controls and monitors the temperature regulation system for the
cabin zones. On the overhead AIR COND panel, the flight crew selects
the desired individual compartment temperature.
The hot air system for cabin temperature control has a hot air valve and
trim air valves controlled by the ZC. The ZC compares the demand to
the actual temperature in each zone.
The ZC then sends the pack outlet temperature demand to both PCs to
satisfy the coldest demand.
For the zones, which require warmer temperature, the ZC signals the
TRIM VALVES to open. Hot air mixes with the pack discharge air and
U3T06191 - U02T4M0 - UM21PZ000000001
the temperature increases. In the case of any duct overheat, the hot air
valve and the trim air valves will automatically close to isolate the system.
The system can be reset when the overheat disappears.
U3T06191 - U02T4M0 - UM21PZ000000001
ZONE TEMPERATURE REGULATION SYSTEM INTRODUCTION

ZONE TEMPERATURE REGULATION SYSTEM
INTRODUCTION (continued)
ENHANCED
The Air Conditioning System Controllers (ACSC) control and monitor
the temperature regulation system for the cabin zones. On the overhead
AIR COND panel, the flight crew selects the desired individual
compartment temperature. The Air Conditioning System Controller
compares the demand to the actual temperature in each zone. Air
Conditioning System Controller 1 monitors the temperature of the
flight deck zone and sends the pack outlet temperature demand to
pack 1. Air Conditioning System Controller 2 monitors the temperature
of the forward and aft cabins and sends the pack outlet temperature
demand to pack 2.
The trim air Pressure Relief Valve (PRV) and the trim air valves are
controlled by the Air Conditioning System Controllers. In the case of
any duct overheat, the Trim air PRV and the trim air valves will
automatically close to isolate the system. The system can be reset
when the overheat disappears.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
ZONE TEMPERATURE REGULATION SYSTEM INTRODUCTION - ENHANCED

This section will highlight the control panels and indications for the air
conditioning system.
CONTROL PANELS
On the overhead panel, the AIR COND panel is used by the pilot to
control the air conditioning system. This panel contains the PACK
switches, the zone temperature selectors, the PACK FLOW control,
and the HOT AIR control switch.
On the overhead, the VENTILATION panel contains the CAB FANS
pushbutton switch. The switch is used to select the recirculation fans
OFF.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001

ECAM PAGES
Basic temperature regulation is accomplished by the packs. Pack
parameters, such as pack flow and bypass valve position are found
on the upper section of the ECAM BLEED page.
The ECAM AIR COND page contains the optimized temperature
regulation parameters, such as duct temperature, zone temperature
and trim air system indications.
The ECAM CRUISE page also contains zone temperature indications.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
CONTROL AND INDICATING - ECAM PAGES
U3T06191 - U02T4M0 - UM21PZ000000001

U3T06191 - U02T4M0 - UM21PZ000000001

COMPONENT LOCATION
The left and right packs are located in the air conditioning bay. The air
conditioning bay is located in the unpressurized belly fairing forward of
the wheel well on the lower fuselage. The belly fairing has inlets for pack
and compartment cooling.
The packs supply air to the mixer unit. The mixer unit is installed at the
rear of the forward cargo compartment. It mixes air from the packs and
re-circulated air from the cabin prior to distribution to each zone.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
COMPONENT LOCATION

The ZC is the interface between the PCs and the Centralized Fault Display
Interface Unit (CFDIU) for test purposes and fault reporting. The ZC test
on the Multipurpose Control and Display Units (MCDUs) initiates a
complete air conditioning test including the packs.
The ACSC are connected to the CFDIU for test purposes and fault
reporting, available on the MCDU.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001

SAFETY PRECAUTIONS
When you work on the aircraft, make sure you obey all the Aircraft
Maintenance Manual (AMM) procedures. This will prevent injury to
personnel and/or damage to the aircraft. Here is an overview of the main
safety procedures related to the air conditioning system.
Make sure that air is not supplied to the air conditioning system from the
main engine, the APU or a ground source during maintenance. Hot
compressed air can cause injury to personnel.
When you are working with harmful products, use protective clothing,
rubber gloves and goggles as necessary.
Do not touch a component until it is sufficiently cool to prevent burns.
Make sure that there are no personnel or equipment near the ram air
outlets (if installed) and inlets. Hot exhaust gases can cause injury to
persons and/or damage to equipment.
Keep away from the moving and energized parts when you operate or
test the valves and the flaps.
U3T06191 - U02T4M0 - UM21PZ000000001
U3T06191 - U02T4M0 - UM21PZ000000001
SAFETY PRECAUTIONS
21 VENTILATION SYSTEM PRESENTATION

GENERAL
There are two ventilation systems on the Single Aisle (SA) family,
avionics ventilation and lavatory and galley ventilation.
AVIONICS VENTILATION
The avionics ventilation system supplements the air conditioning system
to supply cooling air to the avionics equipment. This equipment includes
the avionics compartment, the flight deck instruments and the circuit
breaker panels.
A blower fan and an extraction fan circulate the air through the avionics
equipment.
NOTE: Note: these fans operate continuously as long as the A/C

electrical system is supplied.
The Avionics Equipment Ventilation Computer (AEVC) controls the
fans and the configuration of the skin valves in the avionics ventilation
system based on flight/ground logic and fuselage skin temperature.
There are 3 configurations for the skin air inlet and outlet valves:
- open circuit: both valves open (on ground only),
- closed circuit: both valves closed (in flight or low outside air temperature
on ground). The air is cooled in the skin heater exchanger. The skin heat
U3T06191 - U02T4M0 - UM21PY000000001
exchanger is a chamber which lets the air contact the fuselage skin in
flight,
- intermediate circuit: inlet closed, outlet partially open (smoke removal
in flight or low ventilation airflow condition).
GENERAL FAMILIARIZATION COURSE (CFM56) 21 VENTILATION SYSTEM PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM21PY000000001
GENERAL & AVIONICS VENTILATION
U3T06191 - U02T4M0 - UM21PY000000001
GENERAL & AVIONICS VENTILATION

U3T06191 - U02T4M0 - UM21PY000000001

LAVATORY AND GALLEY VENTILATION
The lavatory and galley ventilation system is completely automatic.
Conditioned cabin air is supplied through the lavatory and galley areas
and is removed from these areas by an extraction fan. The fan pulls air
through the ceiling into an extraction duct. The air is then discharged
overboard through the outflow valve.
NOTE: Note: the extraction fan runs continuously, provided electrical

power is available.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001
LAVATORY AND GALLEY VENTILATION

VENTILATION PANEL
The VENTILATION panel, on the overhead panel contains two P/Bs
associated with the ventilation system. With the BLOWER and
EXTRACT switches in the AUTO position (lights out), the avionics
ventilation system is fully automatic and requires no pilot input.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001
VENTILATION PANEL

ECAM CAB PRESS PAGE
A section of the ECAM CABin PRESSure page displays avionics
ventilation system information. The skin valve configuration is displayed
on this page. On the enhanced system, the valve indication is labeled
OUTLET instead of EXTRACT.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001
ECAM CAB PRESS PAGE

COMPONENT LOCATION
The skin air inlet valve is located on the LH side of the fuselage.
The skin air outlet valve is on the RH side of the fuselage. A small
auxiliary flap will open for the intermediate circuit configuration. This
is thought to be the partially open position.
Both skin valves have a manual override and deactivation device.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001
COMPONENT LOCATION

The AEVC is connected to the Centralized Fault Display Interface Unit
(CFDIU) for test purposes and fault reporting, available on the MCDUs.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001

SAFETY PRECAUTIONS
When you work on A/C, make sure you obey all the Aircraft Maintenance
Manual (AMM) procedures. This will prevent injury to personnel and/or
damage to the A/C. Here is an overview of the main safety procedures
related to the ventilation system.
Do not use force to turn the manual handles of the valves. There are shear
pins in the handles.
Do not use your fingers to operate the deactivation switches. If the system
is energized, the valves could move.
U3T06191 - U02T4M0 - UM21PY000000001
U3T06191 - U02T4M0 - UM21PY000000001
SAFETY PRECAUTIONS
21 CARGO VENTILATION & HEATING SYS PRESENTATION

SYSTEM INTRODUCTION
As an option on the Airbus single aisle family, the forward and aft cargo
compartments can have a ventilation system. In addition, a heating system
may be installed in either or both compartments. Note that the heating
system will only be installed along with a ventilation system.
The operation for both compartments is similar so we will only look at
the forward cargo compartment. Air from the main cabin is drawn down
into the cargo compartment by the extract fan or by differential pressure
in flight. After circulating through the compartment, the air is discharged
overboard.
The operation of the two isolation valves and the extract fan is controlled
automatically by the cargo Ventilation Controller (VC). One VC is able
to control either or both compartments.
For the heating of the cargo compartment, the pilots select the desired
compartment temp and hot bleed air is mixed with the air coming from
the main cabin to increase the temperature if necessary. The supply of
hot air is controlled by the Cargo Heating Controller. Each heated
compartment has a dedicated Cargo Heating Controller. Note that there
is NO direct air conditioning supply to the cargo compartments. The
pilots cannot add "cold" air to the compartments.
U3T06191 - U02T4M0 - UM21PX000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 21 CARGO VENTILATION & HEATING SYS PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM21PX000000001
SYSTEM INTRODUCTION

This section will highlight the control panels and indications for the cargo
ventilation and heating systems.
CONTROL PANELS
On the cockpit overhead panel, the CARGO HEAT panel contains
the controls associated with cargo ventilation and heating. Again,
based on the customer options, several variations may be found:
ventilation in either one compartment or both, or ventilation and
heating in one compartment or both.
For each ventilated cargo compartment there is an ISOLATION
VALVE P/B switch that controls the isolation valves. In the auto
position the cargo VC will automatically open and close the isolation
valves.
In case of cargo smoke detected, the cargo ventilation controller will
automatically close the related isolation valves.
For each heated compartment, the temperature selectors signal the
associated Cargo Heating Controller to move the trim air valves to
adjust the temperature of the air entering the compartment.
The forward cargo trim air system is fed from the cabin hot air valve
but the HOT AIR P/B switch controls the aft cargo compartment hot
U3T06191 - U02T4M0 - UM21PX000000001
air valve.
U3T06191 - U02T4M0 - UM21PX000000001

ECAM COND PAGE
The indications linked to the cargo compartments are displayed on
the ECAM COND page. Note that the indications are only displayed
if the system is installed.
U3T06191 - U02T4M0 - UM21PX000000001
U3T06191 - U02T4M0 - UM21PX000000001
CONTROL AND INDICATING - ECAM COND PAGE

COMPONENT LOCATION
The isolation valves and extract fans of the forward cargo compartment
ventilation system are located behind the compartment sidewall panels.
The air inlets and outlets are protected by grills.
U3T06191 - U02T4M0 - UM21PX000000001
U3T06191 - U02T4M0 - UM21PX000000001
COMPONENT LOCATION

AFT CARGO COMPARTMENT COMPONENT
LOCATION
In the aft cargo compartment the isolation valves and extract fans are
installed in the left sidewall and near the compartment ceiling.
U3T06191 - U02T4M0 - UM21PX000000001
U3T06191 - U02T4M0 - UM21PX000000001
COMPONENT LOCATION - AFT CARGO COMPARTMENT COMPONENT LOCATION

The two cargo heating controllers and the cargo VC are connected to the
Centralized Fault Display Interface Unit (CFDIU) for test purposes and
fault reporting.
U3T06191 - U02T4M0 - UM21PX000000001
U3T06191 - U02T4M0 - UM21PX000000001

SAFETY PRECAUTIONS
When you work on aircraft, make sure that you obey all the AMM
procedures. This will prevent injury to personnel and/or damage to the
aircraft. Here is an overview of the main safety procedures related to the
cargo compartment heating and ventilation system.
When you are in contact with harmful products, use protective clothing,
rubber gloves and goggles.
Do not touch a component until it is sufficiently cool to prevent burns.
U3T06191 - U02T4M0 - UM21PX000000001
U3T06191 - U02T4M0 - UM21PX000000001
SAFETY PRECAUTIONS
21 PRESSURIZATION SYSTEM PRESENTATION

SYSTEM INTRODUCTION
The pressurization system on the Single Aisle (SA) family normally
operates automatically to adjust the cabin altitude and rate of climb to
ensure maximum passenger comfort and safety.
The pressurized areas are:
- the cockpit,
- the avionics bay,
- the cabin,
- the cargo compartments.
The concept of the system is simple. Air is supplied from the air
conditioning packs to the pressurized areas.
An outflow valve is used to regulate the amount of air allowed to escape
from the pressurized areas.
Automatic control of the outflow valve is provided by two Cabin Pressure
Controllers (CPCs). Each CPC controls one electric motor on the outflow
valve assembly. The CPC interface with other A/C computers to optimize
the pressurization/depressurization schedule.
There are two automatic pressurization systems. Each CPC and its electric
motor make one system. Only one system operates at a time with the
other system acting as backup in case of a failure. The system in command
will alternate each flight.
U3T06191 - U02T4M0 - UM21PW000000001
A third motor is installed for manual operation of the outflow valve in

case both automatic systems fail.
To protect the fuselage against excessive cabin differential pressure,
safety valves are installed on the rear pressure bulkhead. The safety valves
also protect against negative differential pressure.
GENERAL FAMILIARIZATION COURSE (CFM56) 21 PRESSURIZATION SYSTEM PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM21PW000000001
SYSTEM INTRODUCTION

This section will highlight the control panels and indications for the
pressurization system.
CONTROL PANEL
The CABIN PRESSure control panel is installed on the overhead
panel. The panel includes both automatic and manual pressurization
controls.
The MODE SELect switch lets the system be used in automatic or
manual mode, in case of failure of the automatic function.
When the manual mode is selected, the MANual Vertical Speed (V/S)
ConTroL switch is used to directly control the outflow valve
(indirectly, the cabin rate of climb) using the third motor.
The guarded DITCHING switch is used to close all lower fuselage
valves so that the A/C can be sealed in the unlikely event of a ditching.
U3T06191 - U02T4M0 - UM21PW000000001
U3T06191 - U02T4M0 - UM21PW000000001
CONTROL AND INDICATING - CONTROL PANEL

ECAM PAGES
The crew can monitor all cabin pressure functions on the ECAM
CABin PRESS page.
Some of the pressurization parameters are repeated on the ECAM
CRUISE page.
U3T06191 - U02T4M0 - UM21PW000000001
U3T06191 - U02T4M0 - UM21PW000000001

COMPONENT LOCATION
Pressurization is achieved by means of a dual gate type outflow valve.
The outflow valve is operated by three electrical motors; two for automatic
mode and one for manual mode.
Two safety valves are installed on the pressure bulkhead at the rear of
the cabin.
U3T06191 - U02T4M0 - UM21PW000000001
U3T06191 - U02T4M0 - UM21PW000000001
COMPONENT LOCATION

The two CPCs are connected to the Centralized Fault Display Interface
Unit (CFDIU) for test purposes and fault reporting.
U3T06191 - U02T4M0 - UM21PW000000001
U3T06191 - U02T4M0 - UM21PW000000001

SAFETY PRECAUTIONS
When you work on A/C, make sure you obey all the Aircraft Maintenance
Manual (AMM) procedures. This will prevent injury to personnel and/or
damage to the A/C. Here is an overview of the main safety procedures
related to the pressurization system.
The outflow valve may be operated manually to pressurize the A/C on
the ground.
Use caution when doing the CPC test from the MCDU. The outflow valve
cycles closed during the test.
U3T06191 - U02T4M0 - UM21PW000000001
U3T06191 - U02T4M0 - UM21PW000000001
SAFETY PRECAUTIONS
30 ICE AND RAIN PROTECTION SYSTEMS PRESENTATION

SYSTEM INTRODUCTION
The ice and rain protection system enables unrestricted operation in icing
conditions and heavy rain.
For anti-icing, hot air or electrical heating protects critical areas of the
aircraft.
The different subsystems of the ice and rain protection system are:
- wing ice protection,
- engine air intake ice protection,
- probe ice protection,
- windshield ice and rain protection,
- drain mast ice protection,
- ice detection system (optional),
- water and waste system ice protection.
U3T06191 - U02T4M0 - UM30PZ000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 30 ICE AND RAIN PROTECTION SYSTEMS PRESENTATION May 05, 2006
U3T06191 - U02T4M0 - UM30PZ000000001
SYSTEM INTRODUCTION

WING ICE PROTECTION
Hot air from the pneumatic system is supplied for the anti-icing of the
three outboard leading edge slats (3, 4 and 5) of each wing. Bleed air
from the engines or the APU is supplied to each wing through a pressure
regulating and shut off valve called Wing Anti-Ice (WAI) valve.
A single P/BSW on the overhead ANTI ICE panel controls WAI supply
to both wings. WAI must be manually selected by the crew and is
available in flight only.
Whenever WAI is selected, the engine idle is increased and the
Takeoff/Go Around (TOGA) limit (max thrust) is decreased by the Full
Authority Digital Engine Control (FADEC). This signal is sent to the
FADEC through the Engine Interface Unit (EIU).
For testing purposes, WAI can be selected on the ground but will be
automatically limited to 30 seconds operation to prevent damage to the
wing leading edge.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
WING ICE PROTECTION
U3T06191 - U02T4M0 - UM30PZ000000001
WING ICE PROTECTION

U3T06191 - U02T4M0 - UM30PZ000000001

ENGINE AIR INTAKE ICE PROTECTION
Each engine air intake is protected from ice by an independent air bleed
supply from the High Pressure (HP) compressor of that engine.
The air is supplied through the engine air intake anti-ice valve.
Engine anti-ice is manually selected by the crew and is available in flight
or on the ground with the engine running. After circulating around the
inlet, the air is ducted overboard.
NOTE: Note: in the event of an electrical power supply failure, this

valve will automatically open when the engine is running.
Whenever engine anti-ice is selected, the engine idle is increased and the
TOGA limit (max thrust) is decreased by the FADEC. The FADEC also
turns on continuous ignition. This signal is sent to the FADEC through
the EIU.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001

U3T06191 - U02T4M0 - UM30PZ000000001

PROBE ICE PROTECTION
Ice protection of the Angle Of Attack (AOA) sensors, pitot probes, static
ports, and Total Air Temperature (TAT) probes is achieved by electrical
heating.
In order to give reliable information to the air data systems, the air data
probes are heated automatically when at least one engine is running. The
probes are arranged in three channels related to the three air data systems:
CAPT, F/O and STBY (Air Data/Inertial Reference Unit (ADIRU) 1, 2,
3). The heating system for each channel is controlled and monitored by
a Probe Heat Computer (PHC) 1, 2, 3.
The PROBE/WINDOW HEAT P/BSW (normally in the AUTO position)
may be used to select the probe heating ON with the engines shut down.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001

U3T06191 - U02T4M0 - UM30PZ000000001

WINDOWS ANTI-ICING AND DEFOGGING
Electrical heating is supplied for windshield anti-icing and cockpit side
window de-fogging.
The front windshields and side windows are heated automatically when
at least one engine is running. The heating system for each side is
controlled and monitored by a Window Heat Computer (WHC) 1, 2.
The PROBE/WINDOW HEAT P/BSW (normally in the AUTO position)
may be used to select the window heating ON with the engines shut down.
The windows are protected against overheat by sensors and flight/ground
logic. The sensors turn off the heat when the temperature reaches the
limit and the windows are heated at a lower power on the ground than in
flight.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001

U3T06191 - U02T4M0 - UM30PZ000000001

RAIN REMOVAL
Rain removal from the windshield is done by two independent wipers
and by a rain repellent system in heavy rain. The wipers operate
independently. The rain repellent is discharged onto the left or right
windshield from a pressurized canister installed at the rear of the cockpit.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
RAIN REMOVAL

DRAIN MAST ICE PROTECTION
There are two drain masts installed on the lower fuselage forward and
aft sections.
When the electrical system is powered, the waste water drain masts are
also electrically heated. Two Control Units located in the cargo
compartments control the heating of the forward and aft drain masts.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001

U3T06191 - U02T4M0 - UM30PZ000000001

ICE DETECTION
An external visual ice indicator with an integral light is installed between
the two windshields.
The ice detection system (if installed) has two separate ice detectors
located on the forward lower section of the fuselage. The ice detectors
send an "ice detected" signal directly to the Flight Warning Computers
(FWCs).
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
ICE DETECTION

MISCELLANEOUS SYSTEMS
It is also possible for the aircraft to have installed electrical heating
systems for:
- potable water supply lines,
- waste water lines,
- water servicing panels.
These heating systems are controlled automatically by Control Units
connected to temperature sensors. The Control Units control multiple
heating elements and are installed in the cargo compartments.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
MISCELLANEOUS SYSTEMS

This section will highlight the control panels and indications for the ice
and rain protection systems.
CONTROL PANEL
The controls for the engine and wing anti-ice systems are located on
the overhead ANTI ICE panel. The probes ice protection and windows
anti-icing systems are controlled from the PROBE/WINDOW HEAT
P/BSW.
Each rain removal system is independently controlled by individual
selectors on the overhead panel, on the left and right hand sides.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
CONTROL AND INDICATING - CONTROL PANEL

ECAM INDICATION
A MEMO appears on the upper ECAM when engine anti-ice or WAI
is selected. WAI valve position indication is available on the BLEED
page when the system is selected.
The optional electronic ice detection system sends warnings directly
to the ECAM though the FWCs.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
CONTROL AND INDICATING - ECAM INDICATION

DRAIN MAST MONITORING
Drain mast heating faults may be displayed either on the Programming
and Test Panel (PTP) of the classic cabin or, on the Flight Attendant
Panel (FAP) of the enhanced cabin.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
CONTROL AND INDICATING - DRAIN MAST MONITORING

Wing and engine anti-ice valve position and the valves P/BSW position
are monitored by the air conditioning Zone Controller (ZC) on the classic
Single Aisle (SA) aircraft. On the A318 and Enhanced-systems versions,
the ZC is replaced by the Air Conditioning System Controller (ACSC).
The ZC or ACSC transmits this information to the Centralized Fault
Display System (CFDS).
All 3 PHCs, both WHCs and the ice detectors are connected directly to
the Centralized Fault Display Interface Unit (CFDIU). Each system menu
is available through the MCDU.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001

SAFETY PRECAUTIONS
When you work on the ice and rain protection system, make sure that
you obey all Aircraft Manual Maintenance (AMM) safety procedures.
This will prevent injury to persons and/or damage to the aircraft. Here is
an overview of the main safety precautions related to the ice and rain
protection system.
Remove the protective covers from the probes before activating the probe
ice protection system.
Do not touch the probes during or immediately after operation. The probes
are hot and can burn you.
Do not touch the anti-ice ducts, slats 3, 4 and 5 and engine air intake lips
until they are cool. Those items stay hot for some time after the engine
shuts down.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
SAFETY PRECAUTIONS

SAFETY PRECAUTIONS (continued)
SPECIFIC WARNINGS
The probe heat system is a fail-safe system in order to keep the probes
and static ports de-iced (in flight) in case of a PHC failure.
The window heat system is designed in order to keep the windows
defogged (in flight) in case of a WHC failure.
If the PHC or WHC power Circuit Breakers (C/Bs) are pulled, the
probe and window heat will come on. Pulling the EIU C/B will have
the same result. The EIU controls the "engine running" signal for
automatic operation. If any of these C/Bs are pulled, all of the heater
C/Bs must also be pulled.
U3T06191 - U02T4M0 - UM30PZ000000001
U3T06191 - U02T4M0 - UM30PZ000000001
SAFETY PRECAUTIONS - SPECIFIC WARNINGS
00 DOCUMENTATION PRESENTATION
GENERAL
A/C documentation products mostly differentiate and address the needs
for:
- Single Aisle family products (A318, A319, A320, A321), with red
brown colored book covers,
- Long Range family products (A330, A340), with green brown colored
book covers.
U3T06191 - U02T4M0 - UM00PX000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 00 DOCUMENTATION PRESENTATION May 05, 2006

U3T06191 - U02T4M0 - UM00PX000000001
GENERAL

GENERAL (continued)
MEDIA AND USERS
Main Media:
- paper,
- microfiche,
- digital.
Digital Documentation:
- AIRNav DVD,
- Airbus On-Line Services (AOLS),
- CDs, PDF media can be used as a back-up source.
NOTE: new data is received by CD media (Temporary Revisions
(TRs) and Technical Follow-Ups (TFUs)).
Typical users:
- flight operations,
- line and base maintenance,
- engineering, shop and overhaul maintenance,
- cabin staff.
This training is dedicated for the line and base maintenance personnel,
to operate and maintain the A/C in the optimum condition.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
GENERAL - MEDIA AND USERS

GENERAL (continued)
ATA 100 STANDARDS
Most manuals follow the ATA guidelines and standards around the
world:
- A/C Maintenance Manual (AMM), Illustrated Parts Catalog (IPC),
A/C Schematic Manual (ASM), A/C Wiring Manual (AWM), ...
- Trouble Shooting Manual (TSM) is not ATA 100 aligned, because
it is defined under an AIRBUS SPECIFICATION.
Most technical documents are divided into ATA chapters from ATA
05 to ATA 80.
Page blocks numbers are used to separate the subjects within manual
chapters into topics for easy reference. The page blocks system applies
to the AMM, Component Maintenance Manual (CMM), Structural
Repair Manual (SRM) and TSM.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
GENERAL - ATA 100 STANDARDS

GENERAL (continued)
ATA BREAKDOWN
The ATA 100 numbering system uses a six digits dash number
breakdown, which divides the documented material into chapter
(system), section (subsystem), sub-section (sub-subsystem) and subject
(unit).
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
GENERAL - ATA BREAKDOWN

GENERAL (continued)
MANUAL CUSTOMIZATION
The technical documentation is customized manuals and
non-customized manuals.
The customized manual contains only the information applicable to
a particular airline or a group of operators like the AMM, TSM, IPC,
...
The non-customized manual contains information applicable to all
airlines for one A/C type family (envelope) or applicable to all Airbus
products (generic).
Non-customized manual is called "envelope" when the information
is applicable only to specific A/C, type or series (id est Single Aisle
family) like the Illustrated Tool and Equipment Manual (TEM),
Service Bulletin (SB), Service Information letter (SIL), Operations
Engineering Bulletin (OEB), Master Minimum Equipment List
(MMEL), SRM, ...
It is called "generic" if the information is applicable to all A/C models,
types or series (id est all AIRBUS types A300, A310, A320, A330,
A340) like the Electrical Standard Practices Manual (ESPM).
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
GENERAL - MANUAL CUSTOMIZATION

LINE AND BASE MAINTENANCE DOCUMENTS
The line and base maintenance documents are:
- TSM,
- Additional Cross Reference Tables (ACRT),
- IPC (airframe),
- Power Plant IPC (PPIPC),
- Support Equipment Summary (SES),
- TEM,
- Tool and Equipment Index (TEI),
- Tool and Equipment Drawings (TED),
- Maintenance Facility Planning (MFP),
- Maintenance Review Board (MRB),
- Maintenance Planning Document (MPD),
- AMM,
- ASM,
- AWM,
- A/C Wiring List (AWL),
- ESPM,
- Consumable Material List (CML),
- Component Location Manual (CLM).
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
LINE AND BASE MAINTENANCE DOCUMENTS

LINE AND BASE MAINTENANCE DOCUMENTS (continued)
MAIN MANUALS FOR LINE MAINTENANCE
Flight Operations:
The MMEL specifies the components or systems which may be
inoperative and the associated operational procedures which allow
the A/C to be cleared for flight.
The MMEL provides the necessary information to operators for
definition of their Minimum Equipment List (MEL).
AIRNav tool for maintenance:
- AMM,
- TSM,
- IPC (airframe),
- ASM,
- AWM,
- AWL,
- ESPM.
NOTE: in a near future, shall be incorporated in AIRNav:
- Standards Manual (SM),
- CML.
The PPIPC is supplied by the engine manufacturer.
Other documents reached via AOLS are:
U3T06191 - U02T4M0 - UM00PX000000001
- CLM,
- MPD, notice that MPD comprises the Time Limited Maintenance
Checks (TLMC),
- ACRT.

U3T06191 - U02T4M0 - UM00PX000000001
LINE AND BASE MAINTENANCE DOCUMENTS - MAIN MANUALS FOR LINE MAINTENANCE

LINE AND BASE MAINTENANCE DOCUMENTS (continued)
AIRNAV DOC NAVIGATOR, PDF MANUALS, EDCI
INDEX
The AIRNav doc system gives access to each major manual and with
extensive hyperlinks and search capabilities.
The AMM, TSM, IPC and the Trouble Shooting function makes the
basic package, whereas the wiring diagram manual collection (ASM,
AWM, AWL) together with the ESPM can be purchased and makes
an optional additional package.
Additionally, added in 2005 release, the SM and the CML will be
incorporated.
The trouble shooting function tool makes possible the navigation
through the TSM Index (page block 101) to find the reported fault
symptom and reach the relevant TSM task.
As a backup means, the PDF manuals are paper like and provides a
simple word search function. Besides, they can be printed.
The Electronic Data Combined Index (EDCI) is mostly used for
engineering and maintenance follow-up.
A selection criteria window and links help to reach Airbus documents.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
LINE AND BASE MAINTENANCE DOCUMENTS - AIRNAV DOC NAVIGATOR, PDF MANUALS, EDCI INDEX

DOCUMENTATION MANAGEMENT
The document management will be seen in this topic.
LINK BETWEEN MANUALS
AIRNav makes full use of the Functional Item Number (FIN)
information. The FIN provides a unique links between the manuals,
and each FIN is a unique reference for Line Replaceable Unit (LRU)
identification.
The AMM is reached from the MPD, the TEM, the MMEL or the
Configuration Deviation List (CDL) and cross-references to the TEM,
MMEL and to the MPD.
The AMM and the IPC are supplemented by the CLM for the
consumable materials described by their specification, supplier code
and applicability versus A/C safety.
The IPC links to the PPIPC and is supplemented by the SM for the
standard parts.
The TSM links to the AMM and to the ASM, and can also link to the
AWM.
TSM procedure is reached via the AIRNav trouble shooting function.
The AWM links to the AWL and to the ESPM, if required for wiring
repair.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - LINK BETWEEN MANUALS

DOCUMENTATION MANAGEMENT (continued)
AMTOSS TASK NUMBERING
The 12 digits Task Number gives the ATA and the detailed page block
by the A/C Maintenance Task Orientated Support System (AMTOSS)
reference.
Searched procedure is found after navigation through the manual and
its table of contents:
- on the PDF manual only the page block is shown,
- on the AIRNav the complete AMTOSS reference is shown.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - AMTOSS TASK NUMBERING

FUNCTION CODE TO PAGE BLOCK RELATIONSHIP
TABLE
For the majority of tasks, the page block in which the cross-referenced
task is contained can be found by using the fourth element of the task
number.
The relationship table is found in AMM Chapter 00 - INTRO.
Here you can see an example with TASK 29-11-43-610-041, whose
function code 610, of group 600 is found in page block 301.
The relevant section and the relevant TASK is found on the page block
301, through the table of contents, equally on:
- the PDF CD (AMM),
- the AIRNav DVD (AMM manual).
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - FUNCTION CODE TO PAGE BLOCK RELATIONSHIP TABLE

FRONT MATTER PAGES AND CHAPTER 00
The preliminary pages found at the beginning of the manual are the
front matter pages and the Chapter 00.
The front matter pages include:
- record of revisions that gives the AMM revision numbers and issue
dates and is updated by the operator,
- list of TRs that is the list of the temporary revisions (concerning all
chapters) which shall be removed from the manual or which remain
still effective,
- list of SBs which are applicable for at least one A/C of the fleet,
- Customer Originated Changes (COCs) that is the list of the COCs
which are applicable for at least one A/C of the fleet,
- specifically for the AMM, the deactivation/reactivation index, that
gives the link to the AMM tasks called from the CDL or from the
MMEL,
- specifically for the TSM, the indexes for warnings and malfunctions
and for the fault messages.
The CHAPTER 00 includes:
- highlights that give the reason for change of the modified data
introduced at last revision,
U3T06191 - U02T4M0 - UM00PX000000001
- List of Effective Pages that lists all effective pages for a given
revision issue. New pages are indicated by "N", Revised by "R" or
Deleted by "D",
- Table of Contents that shows the detailed breakdown of the manual
and lists each chapter and procedures,
- introduction - Chapter 00 that gives explanation on how to use the
manual, the symbols used in the manual and comprises the Effectivity
Table that gives the relationship between the Fleet Serial Number
(FSN) and the Manufacturer Serial Number (MSN) and the A/C model.

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - FRONT MATTER PAGES AND CHAPTER 00

LIST OF EFFECTIVE PAGES AND LIST OF SERVICE
BULLETIN
Revision marker: "N", "R" or "D" indicates pages which are New,
Revised or Deleted respectively.
The incorporation code is the SB configuration in the manual and can
be "S" or "C".
"S" is used to indicate Split or Dual configuration and "C" is used to
indicate Complete (final) configuration.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - LIST OF EFFECTIVE PAGES AND LIST OF SERVICE BULLETIN

REVISION SERVICE AND TEMPORARY REVISION
There are two types of revisions, normal and temporary.
The normal revisions are calendar scheduled. For most manuals they
are every three months.
The Temporary revisions are used for urgent information requiring
immediate attention or advance notification. They are shipped on
yellow pages, yellow floppy disc and today on CD ROM.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - REVISION SERVICE AND TEMPORARY REVISION

AIRCRAFT MODEL AND EFFECTIVITY TABLE
The A/C is identified by digits:
- A/C model is the 4th digit: id est 100, 200, 300, 500, 600,
- engine is the 5th digit,
- thrust rating (Full Authority Digital Engine Control (FADEC) pin
programming) is the 6th digit.
The effectivity table is found in the manual section 00 - INTRO, with
the following data:
- MSN,
- FSN,
- the VERSION indicates the initial ownership, to which company
the A/C was manufactured in.
The page effectivity is by the FSN in the customized manuals and by
the MSN in the non customized manuals.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - AIRCRAFT MODEL AND EFFECTIVITY TABLE

TECH DATA EFFECTIVITY
FSN is the criteria for the page effectivity for the customized manuals
(AMM, ASM, IPC, ...).
Page level effectivity:
- ALL means applicable to the entire customer fleet (NOT applicable
to all A/C of the Airbus world fleet),
- 001-005 means applicable for each MSN from 001 up to 005,
- 001, 005 means applicable for MSN 001 and MSN 005 only.
To distinguish differences in A/C layout or configuration, a
supplementary page is published and distinguished by a specific
configuration code.
Text level effectivity:
- pre or post SB (COC), as long as the SB is not fully embodied in
the customer fleet.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - TECH DATA EFFECTIVITY

TYPICAL USE OF AIRBUS DOCUMENTATION
SCHEDULED MAINTENANCE.
The deferred work packages, selected SBs and the tasks called by
MPD are scheduled.
UN-SCHEDULED MAINTENANCE.
That is the crew entry report on the TECHNICAL LOGBOOK that
makes the maintenance action / reply mandatory.
The FAULT symptom is made typically of the ECAM warning
associated with the BITE fault message, and it is normally printed on
the Post Flight Report (PFR) too.
The maintenance team can use:
- the MMEL or the CDL, consulting a particular permitted
de-activation on the A/C system or A/C part. The AMM contains full
de-activation task and associated procedures,
- the TFU, giving the result of the technical investigation about a
particular warning or event, and its recommendation may include a
"MAINTENANCE ADVICE" for LINE or SHOP maintenance,
- the SIL 00-028/038/041, covering the messages / BITE deviations
and for which the statement "NO MAINTENANCE ACTION, if ..."
may exist.
U3T06191 - U02T4M0 - UM00PX000000001
The technical services team can assist the maintenance team, by

retrieving information from:
- the applicable Flight Operations Telex (FOT), OEB, All Operator
Telex (AOT) or Operator Information Telex (OIT),
- any other document, consulting EDCI,
- any other document, consulting AOLS.
When troubleshooting is unavoidable, the maintenance team is using
the following manuals: TSM, ASM, AMM, IPC, AWM, AWL and
ESPM.

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - TYPICAL USE OF AIRBUS DOCUMENTATION

TROUBLE SHOOTING TOOL
The fault symptom is typically available on the printed out PFR.
The fault symptom can be found in the AIRNav or in the TSM.
In the AIRNav (web technology tool):
- using the AIRNav trouble shooting function, the relevant fault
symptom is found in the index, then linking to the relevant TSM task,
- simultaneously, the fault symptom can be displayed,
- other manuals (AMM, IPC, ASM, ...) can be reached by hyperlinks
from the TSM task.
In the TSM, as a back-up using the PDF media:
- by page turning through its Index or TSM page block 101, and
through its respective entry sections: ECAM, EFIS, LOCAL,
OBSerVations or Centralized Fault Display System (CFDS)/Central
Maintenance System (CMS), the relevant fault symptom is found with
the TSM procedure number cross-referenced.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - TROUBLE SHOOTING TOOL

DEFINITIONS OF TERMS
The following terms are used in the AMM and are defined as follows:
- WARNING calls attention on the use of material, processes, methods,
procedures or limits which must be followed precisely to avoid injury
or death to persons,
- CAUTION calls attention on methods and procedures which must
be followed to avoid damage to equipment,
- NOTE calls attention to methods which make the job easier or
provide supplementary or explanatory information.
U3T06191 - U02T4M0 - UM00PX000000001

U3T06191 - U02T4M0 - UM00PX000000001
DOCUMENTATION MANAGEMENT - DEFINITIONS OF TERMS

05 TIME LIMITS AND MAINTENANCE CHECKS

SCHEDULED MAINTENANCE TASKS & CHECKS IN MPD
This Chapter 05-20-00 "Life Limits and Maintenance Checks" is now
covered in the Maintenance Planning Document (MPD).
The MPD is the repository document for all repetitive scheduled
maintenance tasks declared by Airworthiness Directives (AD/CN), All
Operator Telex (AOT), Inspection Service Bulletins (ISB), Service
Information Letters (SIL), and Modifications (MOD/SB) and analyzed
under the Maintenance Review Board (MRB).
UN-SCHEDULED MAINTENANCE IN AMM SECTION

05-50-00
This Chapter 05-50-00 includes the maintenance checks that you must
do when a flight crew report shows abnormal flight conditions.
Such maintenance actions are divided into two categories of information:
- inspections,
- checks.
U3T06191 - U02T4M0 - UM05PZ000000001
GENERAL FAMILIARIZATION COURSE (CFM56) 05 TIME LIMITS AND MAINTENANCE CHECKS May 05, 2006
U3T06191 - U02T4M0 - UM05PZ000000001
SCHEDULED MAINTENANCE TASKS & CHECKS IN MPD & UN-SCHEDULED MAINTENANCE IN AMM SECTION 05-50-00
05 TIME LIMITS AND MAINTENANCE CHECKS

SCHEDULED REPETITIVE REQUIREMENTS THROUGH
MPD
The main objective of the MPD document is to provide maintenance
planning information necessary for each operator to develop a customized
maintenance program.
MPD reflects all repetitive scheduled maintenance tasks declared by
AD/CN, AOT, ISB, SIL, and MOD/SB and analyzed under the MRB.
A typical scheduled repetitive task (Integrated Drive Generator (IDG)
scavenge filter) is listed with the following data:
- the threshold interval, source document, cross-references to other
manuals or documents (Aircraft Maintenance Manual (AMM) and SIL),
- Man Hours required to accomplish the work,
- the applicability in this Envelope document.
Note the Zonal inspection, requested by C CHECK interval, on the tension
of the fan cowl latches, the AOT, AMM and SIL cross-referenced.
Some maintenance tasks have a higher ranking of requirement, when the
maintenance requirement is identified as:
- "Airworthiness Limitations Item" (ALI) or "Life limit parts",
- "Certification Maintenance Requirements" (CMR).
The approved document MRB REPORT Appendix 1 lists all these
airworthiness approved issues, the ALIs and CMRs.
U3T06191 - U02T4M0 - UM05PZ000000001
The MPD details these airworthiness related items in the "Time controlled
Items" and "Life Limits" sections.
It is the responsibility of each operator to adjust his own maintenance
program in accordance with his National Authority.
U3T06191 - U02T4M0 - UM05PZ000000001
SCHEDULED REPETITIVE REQUIREMENTS THROUGH MPD
AIRBUS S.A.S.
31707 BLAGNAC cedex, FRANCE
STM
REFERENCE U3T06191
MAY 2006
PRINTED IN FRANCE
AIRBUS S.A.S. 2006
ALL RIGHTS RESERVED
AN EADS JOINT COMPANY

WITH BAE SYSTEMS

2X 1 5

Uploaded by

Copyright:

Available Formats

2X 1 5

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2X 1 5

Uploaded by

Copyright:

Available Formats

C e nt r e d e f o rm a ti o n d e t y p e a v i on

Socit Air France 2000

Under no circumstances should this document be used as a reference

It will not be updated.

All rights reserved

GENERAL FAMILIARIZATION COURSE (CFM56) TABLE OF CONTENTS May 11, 2006

70 POWER PLANT CFM56 PRESENTATION

70 POWER PLANT CFM56 PRESENTATION

70 POWER PLANT CFM56 PRESENTATION

70 POWER PLANT CFM56 PRESENTATION

MODULAR CONCEPT - LP ROTOR

70 POWER PLANT CFM56 PRESENTATION

MODULAR CONCEPT - HP ROTOR AND COMBUSTION CHAMBER

70 POWER PLANT CFM56 PRESENTATION

MODULAR CONCEPT - TRANSFER & ACCESSORY GEARBOXES

70 POWER PLANT CFM56 PRESENTATION

- fuel return valve,

70 POWER PLANT CFM56 PRESENTATION

70 POWER PLANT CFM56 PRESENTATION

THRUST REVERSER SYSTEM

THRUST REVERSER SYSTEM

This Page Intentionally Left Blank

70 POWER PLANT CFM56 PRESENTATION

CONTROL AND INDICATING - CONTROL PANELS

70 POWER PLANT CFM56 PRESENTATION

CONTROL AND INDICATING - ECAM ENGINE

70 POWER PLANT CFM56 PRESENTATION

CONTROL AND INDICATING - ECAM ENGINE (ENHANCED)

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - FADEC

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - STARTING

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - FUEL

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - AIR

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - OIL

70 POWER PLANT CFM56 PRESENTATION

COMPONENT LOCATION - THRUST REVERSER

70 POWER PLANT CFM56 PRESENTATION

70 POWER PLANT CFM56 PRESENTATION

When opening the engine cowls:

70 POWER PLANT CFM56 PRESENTATION

LUBRICANTS AND FUELS

70 POWER PLANT CFM56 PRESENTATION

CAUTION: Under no circumstances shall preservative oil or equivalent

STORAGE AND PRESERVATION

36 PNEUMATIC SYSTEM PRESENTATION

36 PNEUMATIC SYSTEM PRESENTATION

APU BLEED/EXTERNAL AIR

SYSTEM INTRODUCTION - ENGINE BLEED & APU BLEED/EXTERNAL AIR

36 PNEUMATIC SYSTEM PRESENTATION

SYSTEM INTRODUCTION - LEAK DETECTION

36 PNEUMATIC SYSTEM PRESENTATION

CONTROL & INDICATING - CONTROL PANEL

36 PNEUMATIC SYSTEM PRESENTATION

CONTROL & INDICATING - ECAM INDICATION

36 PNEUMATIC SYSTEM PRESENTATION

COMPONENT LOCATION - PRESSURE REGULATION COMPONENTS & TEMPERATURE REGULATION COMPONENTS