Tutorial Global Cache - Setup

iRule Tutorial
GC iTach (WF)
This guide will show you
how to set up Global Cache
iTach WiFi Family of
Gateways.
Introduction 2. You will see the port LED lights flash rapidly. This is the indication that the
Gateway is being reset.
This guide will help walk you through the set up of the Global
Cache iTach WiFi family of Gateways. We will show you how to
log into the Gateway the first time and then how to set it up
once you connect it to your network. The set-up of the Global Network Requirements:
Cache WF devices can be done using either MAC, PC or even
The Global Cache iTach WiFi Gateways have a few
a SmartPhone. For this guide we used a PC.
requirements that you will need to follow in order to be success-
ful with the product.
What Does the Guide Cover?
This guide covers the four steps to get your Global Cache iTach 802.11b - These Gateways require a b connection. This can
WiFi Gateway set up on your wireless network. be part of a mixed 802.11b,g,n network but b needs to be at
least available.
Connecting to the WiFi Gateway
AES data encryption - The Gateways require a little bit
Network Settings for the Gateway stronger security than the basic TKIP encryption. So you will
need to make sure that the Password security of the router is
set to AES.
How long will it take?
Following the step-by-step instructions in the guide should only
take you about 10 to 15 minutes. Then you will be able to
switch over to the Builder software and the iRule app.
*Reset Information: If you should need to factory reset the iTach Gateways,
follow the steps below to complete the task.
1. Insert a paperclip into the IR learning port of the Gateway.

(Gently insert the paperclip, the reset is NOT A BUTTON!) IF you push too
far you will end up damaging the IR learning eye of the Gateway.
77
Connecting to the iTach (WF)
Step 1. Find the Gateway Step 2. Connect to Step 3. Gateway Setup

If you open up the Network Gateway Now that we are connected to the Gateway, we need to open our
Properties of your PC. Now you will connect to the Internet browser. In the address window type the following IP address.
You can see the iTach listed Gateway. 169.254.1.70, hit Enter. This will take you into the Setup and
with the MAC Address. Configuration of the iTach WF2IR/SL/CC gateway.
GlobalCache(MAC Address) This will disconnect you
from the internet and allow Next we will select Network Configuration and change the network
Before going onto the next you to setup the network settings so that the Gateway will connect to your wireless network.
step make sure that you settings of the gateway.
have the following informa-
tion written down from your
wireless router.
IP Address Range; Gateway;

Subnet Mask; SSID (Network
Name); Passphrase (Password)
78
Network Settings for iTach (WF)
Step 3. Network Configuration Step 4. Network Configuration Cont...

Once inside the Network Configuration of the Gateway our first step will Now that we have changed the Network type you can see that we have
be to change the Network Type. to enter in all of the information from your router that you wrote down.
The Network Type needs to be changed from Adhoc to Infrastructure. IP Address: It is recommended that you setup a Static IP Address.
Gateway: Gateway of your router.
To make this change simply use the drop down box and select Subnet Mask: Usually 255.255.255.0 but make sure to match yours.
Infrastructure. SSID: This is the network name that the client connects to.
Security Type: This is the type of security that the router is using.
Again it needs to be AES encryption in order to connect to the
gateway properly.
Pass Phrase: Password that the customer uses to connect to the
network.
Click Save!
79
Gateway Setup Success!
Step 6. Network
Step 5. Gateway Reboot Properties Finished
The Gateway once saved will reboot. Once you see this window it will As a final test that the
take approx. 1 minute for the gateway to reboot and if everything was gateway has connected to
entered correctly into the setup it will then connect to the network. the network. If you open up
the Network Properties
To test whether the gateway has connected to your network you can window, you should not
look at the back of the gateway and notice if the power light is blinking longer see the GlobalCache
1 time every second. This is the indication that it is connected to the as a selection.
network.
If the light is not blinking after a minute you will want to check the Net-
work Properties and see if the Gateway has disappeared. If it still does
not get connected to the network you will need to RESET the gateway
and then try the process over. *See Reset Information!
80

Tutorial Global Cache - Setup

Uploaded by

Copyright:

Available Formats

Tutorial Global Cache - Setup

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tutorial Global Cache - Setup

Uploaded by

Copyright:

Available Formats

iRule Tutorial

1. Insert a paperclip into the IR learning port of the Gateway.

Step 1. Find the Gateway Step 2. Connect to Step 3. Gateway Setup

IP Address Range; Gateway;

Step 3. Network Configuration Step 4. Network Configuration Cont...

You might also like