Quick Start Guide of TVI Series DVR DS-7100HGHI-SH

Digital Video Recorder
Quick Start Guide

UD.6L0202B1704A01
Quick Start Guide of Digital Video Recorder
TABLE OF CONTENTS
DVR Pre-Installation ....................................................................................................................................... 4
DVR Installation .............................................................................................................................................. 4
Hard Disk Installation ..................................................................................................................................... 5
Front Panels...................................................................................................................................................... 7
Rear Panels ..................................................................................................................................................... 14
Peripheral Connections ................................................................................................................................. 17
Wiring of Alarm Input ........................................................................................................................... 17
Wiring of Alarm Output ........................................................................................................................ 17
Alarm Connection .................................................................................................................................... 17
RS-485 and Controller Connection .......................................................................................................... 18
Termination Switch Operation ................................................................................................................. 19
Specifications .................................................................................................................................................. 20
Table 1 Specification for DS-7104HQHI-SH........................................................................................... 20
Table 2 Specification for DS-7100HGHI-SH ........................................................................................... 21
HDD Storage Calculation Chart ................................................................................................................... 28
Accessing by Web Browser ............................................................................................................................ 29
Logging In................................................................................................................................................ 29
Live View ................................................................................................................................................. 29
Recording ................................................................................................................................................. 30
Playback ................................................................................................................................................... 31
Log ........................................................................................................................................................... 32
Menu Operation ............................................................................................................................................. 33
Menu Structure......................................................................................................................................... 33
Startup and Shutdown .............................................................................................................................. 33
Live View ................................................................................................................................................. 34
Adding IP Cameras .................................................................................................................................. 34
Record ...................................................................................................................................................... 36
Instant Recording ............................................................................................................................. 36
All-day Recording ............................................................................................................................ 36
Playback ................................................................................................................................................... 37
Backup ..................................................................................................................................................... 38
VCA Alarm .............................................................................................................................................. 39
Access by EZVIZ Cloud P2P ................................................................................................................... 40
Regulatory information
FCC information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Trademarks and Registered Trademarks

Windows and Windows mark are trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
HDMI, HDMI mark and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
The products contained in this manual are authorized by HDMI Licensing LLC with the use right of the HDMI
technology.
VGA is the trademark of IBM.

UPnPTM is a certification mark of the UPnPTM Implementers Corporation.
Other names of companies and product contained in this manual may be trademarks or registered trademarks
of their respective owners.
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to the models listed in the following table.
Series
Model
Type
DS-7100HGHI-SH
DS-7104HGHI-SH
Network DVR
DS-7108HGHI-SH
DS-7100HQHI-SH
DS-7104HQHI-SH
Network DVR
DS-7200HGHI-SH
DS-7204HGHI-SH
Network DVR
DS-7208HGHI-SH
DS-7216HGHI-SH
7200HQHI-SH
DS-7204HQHI-SH
Network DVR
DS-7208HQHI-SH
7300HGHI-SH
DS-7304HGHI-SH
Network DVR
DS-7308HGHI-SH
DS-7316HGHI-SH
DS-7324HGHI-SH
DS-7332HGHI-SH
7300HQHI-SH
DS-7304HQHI-SH
Network DVR
DS-7308HQHI-SH
DS-7316HQHI-SH
8100HGHI-SH
DS-8104HGHI-SH
Network DVR
DS-8108HGHI-SH
DS-8116HGHI-SH
DS-8124HGHI-SH
DS-8132HGHI-SH
8100HQHI-SH
DS-8104HQHI-SH
Network DVR
DS-8108HQHI-SH
DS-8116HQHI-SH
DVR Pre-Installation
The HD-TVI series DVR is highly advanced surveillance equipment that should be installed carefully. Please take
into consideration the following precautionary steps before installation of the DVR.
1. Keep all liquids away from the DVR.
2. Install the DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
DVR Installation
During the installation of the DVR:
1.
2.
3.
4.
5.
6.
7.
8.
Use brackets for rack mounting.

Ensure there is ample room for audio and video cables.
When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.
Connect both the alarm and RS-485 cable.
Allow at least 2cm (0.75-inch) of space between racks mounted devices.
Ensure the DVR is grounded.
Environmental temperature should be within the range of -10 C ~ 55 C, 14F ~ 131F.
Environmental humidity should be within the range of 10% ~ 90%.
Hard Disk Installation

Before you start:
Before installing a hard disk drive (HDD), please make sure the power is disconnected from the DVR. A factory
recommended HDD should be used for this installation.
Up to 8 SATA hard disks can be installed on your DVR.
Tools Required: Screwdriver.
As the installation steps of HDD are similar among different models, here we take the steps of the
DS-7200HGHI-SH and DS-8100 HGHI-SH as the examples.
HDD Installation (A)

Steps:
1. Remove the cover from the DVR by unfastening the screws on the back and side.
2. Connect one end of the data cable to the motherboard of DVR and the other end to the HDD.
3. Connect the power cable to the HDD.
4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
5. Re-install the cover of the DVR and fasten screws.
HDD Installation (B)

Steps:
1. Remove the cover from the DVR by unfastening the screws on the back and side.
2. Install the HDD to the HDD rack using the provided screws, and then fasten the
screws to fix the HDD.
3. Connect one end of the data cable to the motherboard of DVR and the other end to the
HDD.
4. Connect the power cable to the HDD.
5. Re-install the cover of the DVR and fasten screws.
Front Panels
Front Panel of DS-7100HGHI-SH and DS-7104HQHI-SH

Description of Front Panel
No.
Icon
Description
Indicator turns red when DVR is powered up.
Indicator lights in red when data is being read from or written to HDD.
Indicator blinks blue when network connection is functioning properly.
Front Panel of DS-7204/7208HGHI-SH
Front Panel of DS-7216HGHI-SH

No.
Name
POWER
STATUS
Tx/Rx
IR Receiver
USB Interfaces
Function Description
Power indicator turns yellow when the power switch on the real
panel is turned on.
Status indicator blinks red when data is being read from or written to
HDD.
Tx/Rx indictor blinks yellow when network connection is
functioning properly.
Receiver for IR remote controller.
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
Front Panel of DS-7200HQHI-SH

No.
Name
POWER
Power indicator turns yellow when the device s running.

Status indicator blinks red when data is being read from or
STATUS
written to HDD, and turns yellow when the SHIFT function is

realized.
Tx/Rx indictor blinks yellow when network connection is
Tx/Rx
SHIFT
1/MENU
Switch between the numeric or letter input and functions of the

composite keys.
Enter numeral 1;
Access the main menu interface.
Enter numeral 2;
Enter letters ABC;
The F1 button when used in a list field will select all items in the
2/ABC/F1
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
In live view or playback mode, the F1 button can be used to
switch between main and spot video output.
Enter numeral 3;
3/DEF/F2
Enter letters DEF;

The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
Composite
Keys
Enter numeral 4;
4/GHI/ESC
Enter letters GHI;

Exit and back to the previous menu.
Enter numeral 5;
Enter letters JKL;
5/JKL/EDIT
Delete characters before cursor;

Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral 6;
6/MNO/PLAY
Enter letters MNO;

In Playback mode, it is used for direct access to playback
interface.
Enter numeral 7;
7/PQRS/REC
Enter letters PQRS;

Manual record, for direct access to manual record interface;
manually enable/disable record.
8/TUV/PTZ
Enter numeral 8;
No.
Name
Enter letters TUV;
Access PTZ control interface.
Enter numeral 9;
9/WXYZ/PREV
Enter letters WXYZ;

Multi-channel display in live view.
Enter numeral 0;
0/A
Shift the input methods in the editing text field. (Upper and
lowercase, alphabet, symbols or numeric input).
The DIRECTION buttons are used to navigate between different
fields and items in menus.
In the Playback mode, the Up and Down button is used to speed
up and slow down recorded video. The Left and Right button will
DIRECTION
select the next and previous record files.

In Live View mode, these buttons can be used to cycle through
channels.
In PTZ control mode, it can control the movement of the PTZ
camera.
The ENTER button is used to confirm selection in any of the
menu modes.
It can also be used to tick checkbox fields.
ENTER
In Playback mode, it can be used to play or pause the video.

In single-frame Playback mode, pressing the button will advance
the video by a single frame.
In Auto-switch mode, it can be used to stop /start auto switch.
USB Interface
IR Receiver
Universal Serial Bus (USB) ports for additional devices such as

USB mouse and USB Hard Disk Drive (HDD).
Receiver for IR remote control.
Front Panel of DS-7300HGHI-SH and DS-7300HQHI-SH

No.
Name
POWER
READY
1
STATUS
Power indicator lights in green when DVR is powered up.
Ready indicator is normally green, indicating that the DVR is
Indicator turns green when DVR is controlled by an IR remote control
with the address from 1~254;
Indicator turns red when the SHIFT button is used;
Indicator does not light when the DVR is controlled by a keyboard or
by the IR remote control with the address of 255;
Indicator turns green when the DVR is controlled by IR remote control
No.
Name
ALARM
HDD indicator blinks in red when data is being read from or written to
HDD.
Tx/Rx indictor blinks in green when network connection is functioning
properly.
HDD
Tx/Rx
2
(with the address from 1~254) and keyboard at the same time , and the
SHIFT button is not used;
Indicator turns orange : (a) when the DVR is controlled by IR remote
control (with the address from 1~254) and keyboard at the same time
and the SHIFT button is used as well; (b) when the DVR is controlled
by IR remote control (with the address from 1~254) and the SHIFT
button is used.
Alarm indicator turns red when a sensor alarm is detected.
DVD-R/W
Slot for DVD-R/W.

Switch between the numeric or letter input and functions of the
SHIFT
composite keys. (Input letter or numbers when the light is out; Realize
functions when the light is red.)
1/MENU
Enter numeral 1;
Access the main menu interface.
Enter numeral 2;
Enter letters ABC;
The F1 button when used in a list field will select all items in the list.
2/ABC/F1
In PTZ Control mode, it will turn on/off PTZ light and when the image
is zoomed in, the key is used to zoom out.
In live view or playback mode, the F1 button can be used to switch
between main and spot video output.
Enter numeral 3;
3/DEF/F2
Enter letters DEF;

The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
Enter numeral 4;
Composite
4/GHI/ESC
Enter letters GHI;

Keys
Enter numeral 5;
Enter letters JKL;
5/JKL/EDIT
Delete characters before cursor;

Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
Enter numeral 6;
6/MNO/PLAY
Enter letters MNO;

In Playback mode, it is used for direct access to playback interface.
Enter numeral 7;
7/PQRS/REC
Enter letters PQRS;

Manual record, for direct access to manual record interface; manually
enable/disable record.
Enter numeral 8;
8/TUV/PTZ
Enter letters TUV;

Access PTZ control interface.
9/WXYZ/PREV
Enter numeral 9;
Enter letters WXYZ;
10
No.
Name
Multi-channel display in live view.
Enter numeral 0;
Shift the input methods in the editing text field. (Upper and lowercase,
0/A
alphabet, symbols or numeric input).

The DIRECTION buttons are used to navigate between different fields
and items in menus.
In the Playback mode, the Up and Down button is used to speed up and
slow down recorded video. The Left and Right button will select the
DIRECTION
next and previous record files.

channels.
In PTZ control mode, it can control the movement of the PTZ camera.
The ENTER button is used to confirm selection in any of the menu

modes.
ENTER

In single-frame Playback mode, pressing the button will advance the
video by a single frame.
Power on/off switch.
POWER
Move the active selection in a menu. It will move the selection up and
down.
6
JOG SHUTTLE Control
In Live View mode, it can be used to cycle through different channels.

In the Playback mode, it can be used to jump 30s forward/backward in
video files.
In PTZ control mode, it can control the movement of the PTZ camera.
USB Interface
IR Receiver
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
DS-8100HGHI-SH and DS-8100HQHI-SH

No.
1
Name
Status
Indicators
ALARM
READY
Alarm indicator turns red when a sensor alarm is detected.
Ready indicator is normally blue, indicating that the DVR is
11
No.
Name
STATUS
HDD
Tx/Rx
GUARD
Indicator turns blue when DVR is controlled by an IR remote.
Indicator turns red when controlled by a keyboard and orange when
IR remote and keyboard is used at the same time.
Indicator does not light when the DVR is controlled by the IR remote
control with the address of 255.
HDD indicator blinks in red when data is being read from or written
to HDD.
Tx/Rx indictor blinks in blue when network connection is functioning
properly.
Indicator turns blue when the device is armed;
Indicator does not light when the device is disarmed;
The arm/disarm state can be initiated by pressing and holding on the
ESC button for more than 3 seconds in live view mode.
Switch to the corresponding channel in Live view or PTZ Control
mode.
Input numbers and characters in Edit mode.
Alphanumeric Buttons
Switch between different channels in Playback mode.

The light of the button is blue when the corresponding channel is
recording; it is red when the channel is in network transmission
status; it is pink when the channel is recording and transmitting.
The DIRECTION buttons are used to navigate between different
fields and items in menus.
In the Playback mode, the Up and Down button is used to speed up
and slow down recorded video. The Left and Right button will select
DIRECTION
the next and previous record files.

channels.
Control
Buttons
camera.
The ENTER button is used to confirm selection in any of the menu
modes.
ENTER

In single-frame Playback mode, pressing the button will advance the
video by a single frame.
Move the active selection in a menu. It will move the selection up
and down.
In Live View mode, it can be used to cycle through different
channels.
JOG SHUTTLE Control
In the Playback mode: the outer ring is used to speed up or slow

down the record files and the inner ring is used to jump 30s
forward/backward in records files.
camera.
POWER
Power on/off switch.
12
No.
6
Name
USB Interfaces
ESC
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
Arm/disarm the DVR in live view mode.
Enter the Manual Record setting menu.
REC/SHOT
In PTZ control settings, press the button and then you can call a PTZ
preset by pressing Numeric button.
It is also used to turn audio on/off in the Playback mode.
Enter the Playback menu;
PLAY/AUTO
ZOOM+
Auto scan in the PTZ Control mode.

Zoom in the PTZ camera in the PTZ Control setting.
Adjust focus in the PTZ Control menu.
A/FOCUS+
It is also used to switch between input methods (upper and lowercase

alphabet, symbols and numeric input).
Edit text fields. When editing text fields, it will also function as a
Backspace button to delete the character in front of the cursor.
EDIT/IRIS+
On checkbox fields, pressing the button will tick the checkbox.

In PTZ Control mode, the button adjusts the iris of the camera.
In Playback mode, it can be used to generate video clips for backup.
Enter/exit the folder of USB device and eSATA HDD.
Composite
MAIN/SPOT/Z
Keys
OOM-
Switch between main and spot output.

In PTZ Control mode, it can be used to zoom out the image.
Select all items on the list when used in a list field.
F1/ LIGHT
In PTZ Control mode, it will turn on/off PTZ light (if applicable).
In Playback mode, it is used to switch between play and reverse play.
F2/ AUX
Cycle through tab pages.

In synchronous playback mode, it is used to switch between channels.
Press the button will help you return to the Main menu (after
successful login).
Press and hold the button for 5 seconds will turn off audible key
MENU/WIPER
beep.
In PTZ Control mode, the MENU/WIPER button will start wiper (if
applicable).
In Playback mode, it is used to show/hide the control interface.
Switch between single screen and multi-screen mode.
PREV/FOCUS-
In PTZ Control mode, it is used to adjust the focus in conjunction

with the A/FOCUS+ button.
Enter the PTZ Control mode.
PTZ/IRIS-
In the PTZ Control mode, it is used to adjust the iris of the PTZ
camera.
IR Receiver
DVD-R/W
Slot for DVD-R/W.
13
Rear Panels
The rear panel vaires according to different models.
DS-7100HGHI-SH and DS-7100HQHI-SH

Description of Rear Panel
No.
1
2
3
4
5
6
7
8
9
Item
VIDEO IN
HDMI
VGA
AUDIO OUT
AUDIO IN
Network Interface
USB Port
GND
Power Supply
Description
BNC interface for TVI and analog video input.
HDMI video output connector.
DB15 connector for VGA output. Display local video output and menu.
RCA connector.
RCA connector.
Connector for network
Universal Serial Bus (USB) port for additional devices.
Ground
DC 12V power supply.
DS-7200HGHI-SH
DS-7200HQHI-SH
No.
Item
Description
1
2
VIDEO IN
AUDIO IN

RCA connector
3
4
AUDIO OUT
VGA
RCA connector
DB15 connector for VGA output. Display local video output and menu.
5
6
HDMI
USB Port

7
8
Network Interface
RS-485 Interface

Connector for RS-485 devices.
9
10
Power Supply
Power Switch
12V DC power supply.

Switch for turning on/off the device.
14
11
GND
Ground
12
Alarm In/Out (for

DS-7200HQHI-SH)
Connectors for alarm inputs and alarm outputs.
DS-7316HQHI-SH and DS-7316HGHI-SH
DS-7332HGHI-SH
DS-8116HGHI-SH
DS-8132HGHI-SH
15
DS-8100HQHI-SH
No.
Item
Description
VIDEO IN
VIDEO OUT
BNC connector for video output.
AUDIO IN
RCA connector
USB Port
HDMI

DS-8124/8132HGHI-SH provides HDMI1 and HDMI2 interfaces.
VGA
DB15 connector for VGA output. Display local video output and
menu.
AUDIO OUT
RCA connector
Network Interface
RS-485 Interface
Connector for RS-485 devices. T+ and T- pins connect to R+ and Rpins of PTZ receiver respectively.
D+, D- pin connects to Ta, Tb pin of controller. For cascading
devices, the first DVRs D+, D- pin should be connected with the
D+, D- pin of the next DVR.
Connector for alarm input.
Connector for alarm output.
10
Power Supply
100 ~ 240V AC power supply.
11
Power Switch
Switch for turning on/off the device.
12
GND
Ground
13
LINE IN
BNC connector for audio input.
14
eSATA
Connects external SATA HDD, CD/DVD-RW.
15
RS-232 Interface
Connector for RS-232 devices.
16
Peripheral Connections
Wiring of Alarm Input
The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram.
If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the
device.
Wiring of Alarm Output

To connect to an alarm output (AC or DC load), use the following diagram:
DC Load Connection Diagram
AC Load Connection Diagram
For DC load, the jumpers can be used within the limit of 12V/1A safely.
To connect an AC load, jumpers should be left open (you must remove the jumper on the motherboard in the
DVR). Use an external relay for safety (as shown in the figure above).
There are 4 jumpers (JP1, JP2, JP3, and JP4) on the motherboard, each corresponding with one alarm output. By
default, jumpers are connected. To connect an AC load, jumpers should be removed.
Example:
If you connect an AC load to the alarm output 3 of the DVR, then you must remove the JP 3.
Alarm Connection
To connect alarm devices to the DVR:
1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block.
2. Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part.
Ensure signal cables are in tight.
17
3. Connect pluggable block back into terminal block.
RS-485 and Controller Connection

For DS-7200HGHI-SH and DS-7200HQHI-SH
To connect PTZ to the DVR:

1. Disconnect pluggable block from the RS-485 terminal block.
2. Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange
part. Ensure signal cables are in tight.
3. Connect A+ on PTZ to D+ on terminal block and B- on controller to D- on terminal block. Fasten stop
screws.
For DS-7300HGHI&HQHI-SH and DS-8100HGHI&HQHI-SH
To connect PTZ to the DVR:

1. Disconnect pluggable block from the RS-485 terminal block.
3. Connect A+ on PTZ to T+ on terminal block and B- on controller to T- on terminal block. Fasten stop
screws.
To connect a controller to the DVR:
1. Disconnect pluggable block from the KB terminal block.
18
3. Connect Ta on controller to D+ on terminal block and Tb on controller to D- on terminal block. Fasten stop
screws.
Make sure both the controller and DVR are grounded.
Termination Switch Operation
This function is applicable to the DS-7300 and DS-8100 series DVR.

The termination switch is placed on the mainboard instead of the rear panel. Open the upper cover and turn
on/off the SW switch if needed.
Purpose:
To connect the DVR with several speed domes, the bus topology can be adopted, which means the speed domes
are connected with each other via the R+ and R- of RS-485 serial interface. But due to the impedance of 485 wire,
the longer the wire is, the greater the impedance gets.
To avoid the signal reduction caused by the great impedance of long distance transmission, please connect two
120 resistors in the circuit: one resistor between the DVR and the nearest speed dome, and the other one after the
furthest speed dome.
Steps:
1. Turn on the SW switches on the DVR and the furthest speed dome.
2. Keep other SW switches off.
The connection diagram and status of each SW switch are shown in the following figure.
19
Specifications
Table 1 Specification for DS-7104HQHI-SH
Model
DS-7104HQHI-SH
Video compression
H.264
Analog and HD-TVI
4-ch
video input
BNC interface (1.0Vp-p, 75 )
Video/Audio
Supported camera
input
types
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS

Audio compression
Audio input / Two-way
G.711u
1-ch, RCA (2.0 Vp-p, 1 K)
audio in
1920 1080 / 60 Hz,1280 1024 / 60 Hz, 1280 720 / 60 Hz, 1024 768 / 60
HDMI / VGA output
Hz
Main stream: 1080P / 720P / VGA / WD1 / 4CIF / CIF
Encoding resolution
Sub-stream: WD1(non-real-time) / 4CIF(non-real-time) / CIF / QCIF / QVGA
Main stream: 1/16 fps ~ Real time frame rate
Frame rate
Sub-stream: 1/16 fps ~ Real time frame rate
Video/Audio
Video bitrate
32 Kbps-10 Mbps
Audio output
1-ch, RCA (Linear, 1K)
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
Video, Video & Audio
Synchronous playback
4-ch
Playback resolution
1080P / 720P / VGA / WD1 / 4CIF / CIF / QVGA / QCIF
Remote connections
128
output
Network
management
TCP/IP, PPPoE, DHCP, EZVIZ Cloud P2P, DNS, DDNS, NTP, SADP, SMTP,
Network protocols
SNMP, NFS, iSCSI, UPnP, HTTPS
SATA
1 SATA interface
Capacity
Up to 4 TB capacity for each disk
External
Network interface
1; 10M / 100M self-adaptive Ethernet interface
interface
USB port
2 USB2.0
Power supply
12V DC
Hard disk
Consumption
15W
(without hard disks)
General
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Dimensions
200 200 45mm (7.9 7.9 1.8 inch)
(W D H)
Weight
0.8 kg / 1.8lb
20
Table 2 Specification for DS-7100HGHI-SH

Model
DS-7104HGHI-SH
Video compression
H.264
Analog and HD-TVI
4-ch
video input
Video/Audio
Supported camera
input
types
DS-7108HGHI-SH
8-ch
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS

Audio compression
Audio input / Two-way
G.711u
1-ch, RCA (2.0 Vp-p, 1 K)
audio in
1920 1080 / 60 Hz,1280 1024 / 60 Hz, 1280 720 / 60 Hz, 1024 768 / 60
HDMI / VGA output
Hz
Main stream: 1080P(non-real-time) / 720P / VGA / WD1 / 4CIF / CIF
Encoding resolution
Frame rate
Video/Audio
Video bitrate
32 Kbps-6 Mbps
Audio output
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
1080P / 720P / VGA / WD1 / 4CIF / CIF / VGA / CIF
Remote connections
128
output
8-ch
Network
management
Network protocols
SATA
1 SATA interface
Capacity
External
Network interface
1; 10M / 100M self-adaptive Ethernet interface
interface
USB port
2 USB2.0
Power supply
12V DC
Hard disk
Consumption
15W
General
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Dimensions
200 200 45mm
(W D H)
Weight
(7.9 7.9 1.8 inch)

0.8 kg / 1.8lb
21
280 210 45mm

(11 8.3 1.8 inch)
0.8 kg / 1.8lb

Model
DS-7204HGHI-SH
DS-7208HGHI-SH
DS-7216HGHI-SH
8-ch
16-ch
Video compression
H.264
Analog and HD-TVI video
4-ch
input
Supported camera types
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS
Video/Audio
input
1-ch
2-ch
2-ch
IP video input
Up to 2.0MP resolution
Audio compression
Audio input / Two-way audio
in
HDMI / VGA output
G.711u
1-ch, RCA (2.0 Vp-p, 1 K)
1920 1080 / 60 Hz,1280 1024 / 60 Hz, 1280 720 / 60 Hz, 1024
768 / 60 Hz
Main stream: 1080P(non-real-time) / 720P / VGA / WD1 / 4CIF / CIF
Encoding resolution
Sub-stream: WD1(non-real-time) / 4CIF(non-real-time) / CIF / QCIF /

QVGA
Frame rate
Video/Audio
output
Video bitrate
32 Kbps-6 Mbps
Audio output
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
Remote connections
128
8-ch
16-ch
Network
management
Network protocols
TCP/IP, PPPoE, DHCP, EZVIZ Cloud P2P, DNS, DDNS, NTP, SADP,
SMTP, SNMP, NFS, iSCSI, UPnP, HTTPS
SATA
1 SATA interface
2 SATA interfaces
Capacity
Hard disk
1; 10M / 100M /
Network interface
interface
External
interface
1; standard RS-485 serial interface, half-duplex
USB port
2 USB2.0
Power supply
12V DC
15W
20W
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Chassis
1U chassis
self-adaptive
30W
380mm 1U chassis
380 290 48mm
Dimensions
(W D H)
1000M
Ethernet interface
Serial interface
Consumption
General
1; 10M / 100M self-adaptive Ethernet
315 242 45mm (12.4 9.5 1.8 inch)
(15.0 11.4 1.9

inch)
Weight
1.5Kg (3.3lb)
22
2Kg (4.4lb)

Model
DS-7204HQHI-SH
Video compression
H.264
Analog and HD-TVI
4-ch
video input
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS
Video/Audio
input
DS-7208HQHI-SH
8-ch
2-ch
IP video input
Up to 2.0MP resolution
Audio compression
G.711u
Audio input
4-ch, RCA (2.0 Vp-p, 1 K)
Two-way audio in
1-ch, RCA (2.0 Vp-p, 1 K) (using the 1st channel of audio input)
1920 1080 / 60 Hz,1280 1024 / 60 Hz, 1280 720 / 60 Hz, 1024 768 / 60
HDMI / VGA output
Hz
Main stream: 1080P / 720P / VGA / WD1 / 4CIF / CIF
Encoding resolution
Frame rate
Video/Audio
Video bitrate
32 Kbps-10 Mbps
Audio output
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
Remote connections
128
output
8-ch
Network
management
Network protocols
SATA
1 SATA interface
2 SATA interfaces
Capacity
Network interface
1; 10M / 100M / 1000M self-adaptive Ethernet interface
External
Serial interface
1; standard RS-485 serial interface, half-duplex
interface
Alarm in/out
4/1
USB port
2 USB2.0
Power supply
12V DC
Hard disk
Consumption
8/4
15W
30W
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Chassis
1U chassis
380mm 1U chassis
Dimensions
315 242 45mm
380 290 48mm
(W D H)
(12.4 9.5 1.8 inch)
(15.0 11.4 1.9 inch)
1.5Kg (3.3lb)
2Kg (4.4lb)
General
Weight
23

DS-7304HG
HI-SH
Model
Video compression
H.264
Analog and HD-TVI

video input
4-ch
Supported camera
types
Video/
Audio input
IP video input
DS-7308HGHI
-SH
DS-7316HG
HI-SH
DS-7324HGHI
-SH
DS-7332HGHI
-SH
8-ch
16-ch
24-ch
32-ch

720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS
1-ch
(up to 5-ch)
2-ch
(up to 10-ch)
2-ch
(up to 18-ch)
8-ch (up to 32-ch)
Up to 2MP resolution
Audio compression
G.711u
Audio input
4-ch, RCA (2.0 Vp-p, 1 K)
Two-way audio in
1-ch, RCA (2.0 Vp-p, 1 K)
HDMI / VGA
output
1920 1080/60 Hz ,1280 1024/60 Hz, 1280 720/60 Hz, 1024 768/60 Hz
CVBS output
1-ch, BNC (1.0 Vp-p, 75 ), resolution: PAL: 704

576, NTSC: 704 480
Not available
Main stream: 1080P (non-real-time) / 720P / WD1 / VGA / 4CIF / CIF

Encoding resolution
Sub-stream: WD1 (non-real-time)/ 4CIF(non-real-time) / CIF / QCIF / QVGA
Frame rate
Video/
Audio
output
Network
management

Video bitrate
32 Kbps-6 Mbps
Audio output
2-ch, RCA (Linear, 1K, for VGA output and

CVBS output respectively)
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
Synchronous
playback
4-ch
Playback resolution
Remote connection
128
Network protocols
TCP/IP, PPPoE, DHCP, EZVIZ Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, SNMP,
NFS, iSCSI, UPnP, HTTPS, ONVIF
Type
4 SATA interfaces for 4 HDDs; 1 eSATA interface
Capacity
Network interface
8-ch
16-ch
24-ch
32-ch
Hard disk
External
interface
General
Serial interface
RS-232, RS-485, Keyboard
USB port
3 USB2.0
Alarm in / out
16 / 4
Power supply
100 ~ 240VAC, 47 ~ 63HZ
Consumption
Working
temperature
30W
Working humidity
10% ~ 90%
Chassis
19-inch rack-mounted 1.5U chassis
Dimensions (W D
H)
Weight
40W
55W
-10 C ~+55 C (14 F ~ 131 F)
445 390 70 mm (17.5 15.3 2.7 inch)

5Kg (11.0lb)
24
55W
65W

Model
DS-7304HQHI-SH
Video compression
H.264
DS-7316HQHI-SH
8-ch
16-ch
Analog and HD-TVI
4-ch
video input
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS
Video/Audio
input
DS-7308HQHI-SH
2-ch ( up to 6-ch)
2-ch ( up to 10-ch)
2-ch ( up to 18-ch)
IP video input
Audio compression
G.711u
Audio input
4-ch, RCA (2.0 Vp-p, 1 K)
Two-way audio in
1-ch, RCA (2.0 Vp-p, 1 K)
HDMI / VGA output
1920 1080/60 Hz ,1280 1024/60 Hz, 1280 720/60 Hz, 1024 768/60 Hz
CVBS output
1-ch, BNC (1.0 Vp-p, 75 ), resolution: PAL: 704 576, NTSC: 704 480
Main stream: 1080P / 720P / VGA / 4CIF / CIF
Encoding resolution
Sub-stream: WD1 (non-real-time)/ 4CIF(non-real-time) / CIF / QCIF / QVGA
Frame rate
Video/Audio
Video bitrate
32 Kbps-10 Mbps
Audio output
2-ch, RCA (Linear, 1K, for VGA output and CVBS output respectively)
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
output
Remote connection
8-ch
16-ch
128
Network
management
Network protocols
SNMP, NFS, iSCSI, UPnP, HTTPS, ONVIF
Type
Capacity
Network interface
External
Serial interface
RS-232, RS-485, Keyboard
interface
USB port
3 USB2.0
Alarm in / out
16 / 4
Power supply
100 ~ 240VAC, 47 ~ 63HZ
Hard disk
Consumption
30W
40W
General
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Chassis
19-inch rack-mounted 1.5U chassis
Dimensions (W D H)
445 390 70 mm (17.5 15.3 2.7 inch)
Weight
5Kg (11.0lb)
25
55W

DS-8104HG
HI-SH
Model
Video compression
H.264
Analog and HD-TVI

video input
4-ch
Supported camera
types
Video/Audio
input
IP video input
DS-8108HG
HI-SH
DS-8116HGHISH
DS-8124HGH
I-SH
DS-8132HGH
I-SH
8-ch
16-ch
24-ch
32-ch

720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS
1-ch
(up to 5-ch)
2-ch
(up to 10-ch)
2-ch
(up to 18-ch)
16-ch (up to 32-ch)
16-ch
16-ch
Audio compression
G.711u
4-ch
Audio input
Two-way audio in
HDMI / VGA output
CVBS output
8-ch
16-ch
RCA (2.0 Vp-p, 1 K)

1-ch, RCA (2.0 Vp-p, 1 K)
1920 1080/60 Hz, 1280 1024/60 Hz, 1280 720/60 Hz, 1024 768/60 Hz
DS-8124/8132HGHI-SH provides HDMI1 / VGA output and HDMI2 output
1-ch, BNC (1.0 Vp-p, 75 ), resolution: PAL: 704
Not available
576, NTSC: 704 480
Main stream: 1080P (non-real-time) / 720P / WD1/ VGA / 4CIF / CIF
Encoding resolution
Sub-stream: WD1(12fps) / 4CIF(12fps) / CIF / QCIF / QVGA
Frame rate
Video/Audio
output
Network
management

Video bitrate
32 Kbps-6Mbps
Audio output
2-ch, RCA (Linear, 1K, for VGA output and

CVBS output respectively)
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
8-ch
16-ch
24-ch
32-ch
Remote connection
128
Network protocols
TCP/IP, PPPoE, DHCP, EZVIZ Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, SNMP,
NFS, iSCSI, UPnP, HTTPS, ONVIF
Type
Capacity
Network interface
2; 10M / 100M / 1000M self-adaptive Ethernet interfaces
Serial interface
RS-232, RS-485, Keyboard;
USB port
3 USB2.0
Alarm in / out
16 / 4
Power supply
100 ~ 240VAC, 47 ~ 63HZ
Consumption
30W
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Chassis
19-inch rack-mounted 2U chassis
Hard disk
External
interface
General
Dimensions (W D
H)
Weight
16 / 8
40W
55W
445 470 90 mm (17.5 18.5 3.5 inch)

8Kg (17.6 lb)
26
60W
67W

Model
Video/Audio
input
DS-8104HQHI-SH
DS-8108HQHI-SH
DS-8116HQHI-SH
8-ch
16-ch
Video compression
H.264
Analog and HD-TVI
4-ch
video input
720P/25, 720P/30, 720P/50, 720P/60, 1080P/25, 1080P/30, CVBS

2-ch (up to 6-ch)
2-ch (up to 10-ch)
2-ch (up to 18-ch)
IP video input
Audio compression
G.711u
4-ch
Audio input
Two-way audio in
HDMI / VGA output
CVBS output
8-ch
16-ch
RCA (2.0 Vp-p, 1 K)

1-ch, RCA (2.0 Vp-p, 1 K)
1920 1080 / 60 Hz, 1280 1024 / 60 Hz, 1280 720 / 60 Hz, 1024 768 / 60
Hz
1-ch, BNC (1.0 Vp-p, 75 ), resolution: PAL: 704 576, NTSC: 704 480
Main stream: 1080P / 720P / WD1/ VGA / 4CIF / CIF
Encoding resolution
Frame rate
Video/Audio
output
Network
management
Video bitrate
32 Kbps-10 Mbps
Audio output
2-ch, RCA (Linear, 1K, for VGA output and CVBS output respectively)
Audio bitrate
64 Kbps
Dual-stream
Support
Stream type
4-ch
Playback resolution
Remote connection
128
Network protocols
8-ch
16-ch
SNMP, NFS, iSCSI, UPnP, HTTPS, ONVIF
Type
Capacity
Network interface
2; 10M / 100M / 1000M self-adaptive Ethernet interfaces
External
Serial interface
RS-232, RS-485, Keyboard;
interface
USB port
3 USB2.0
Alarm in / out
16 / 4
Power supply
100 ~ 240VAC, 47 ~ 63HZ
Hard disk
Consumption
General
35W
45W
Working temperature
-10 C ~+55 C (14 F ~ 131 F)
Working humidity
10% ~ 90%
Chassis
19-inch rack-mounted 2U chassis
Dimensions (W D H)
445 470 90 mm (17.5 18.5 3.5 inch)
Weight
8Kg (17.6 lb)
27
65W
HDD Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a
fixed bit rate.
Bit Rate
96K
128K
160K
192K
224K
256K
320K
384K
448K
512K
640K
768K
896K
1024K
1280K
1536K
1792K
2048K
4096K
8192K
16384K
Storage Used
42M
56M
70M
84M
98M
112M
140M
168M
196M
225M
281M
337M
393M
450M
562M
675M
787M
900M
1800M
3600M
7200M
Please note that supplied values for storage space used are just for reference. Storage space used is estimated by
formulas and may have some deviation from actual value.
28
Accessing by Web Browser

Logging In
You can get access to the device via web browser. Open web browser, input the IP address of the device and then
press Enter. The login interface appears.
Input the user name and password, and click the Login button.
You may use one of the following listed web browsers: Internet Explorer 6.0, Internet Explorer 7.0, Internet
Explorer 8.0, Internet Explorer 9.0, Internet Explorer 10.0, Apple Safari, Mozilla Firefox, and Google
Chrome.
The supported resolutions include 1024*768 and above.
The default IP address is 192.0.0.64.
The default user name is admin, and password is 12345.
You are highly recommended to change the default password right after the first login to avoid safety
problem.
When you log in for the first time, the system will remind you to install the Plug-in control. After the installation,
you can configure and manage the device remotely.
Live View
The live view interface appears by default when you log in the device.
Interface Introduction
No.
Name
Description
Channel List
Displays the list of channels and the playing and recording status of each
29
No.
Name
Description
channel.
Live View Window
Displays the image of channel, and multi-window division is supported.
Play Control Bar
Play control operations are supported.

Pan, tilt, zoom operations are supported, as well as preset editing and calling.
PTZ Control
PTZ function can only be realized if the connected camera supports PTZ control.
Video Parameters
Configuration
Brightness, contrast, saturation and hue of the image can be edited.
Start Live View

Steps:
1. In the live view window, select a playing window by clicking the mouse.
2. Double click a camera from the device list to start the live view.
3. You can click the
button on the toolbar to start the live view of all cameras on the device list.
Refer to the following table for the description of buttons on the live view window:
Icon
Description
Icon
Description
Select the window-division mode
Previous page
Start/Stop all live view
Next page
Capture pictures in the live view

/
mode
/
Start/Stop all recording
Enable/Disable digital zoom
Open/Close audio
Start/Stop two-way Audio
Adjust volume
Recording
Before you start
Make sure the device is connected with HDD or network disk, and the HDD or network disk has been initialized
for the first time to use.
Two recording types can be configured: Manual and Scheduled. The following section introduces the
configuration of scheduled recording.
Steps:
1. Click Remote Configuration> Camera Settings> Record Schedule to enter Record Schedule settings
interface.
2. Select the camera to configure the record schedule.
3. Check the checkbox of Enable Record Schedule to enable recording schedule.
4. Click Edit to edit record schedule.
5. Choose the day in a week to configure scheduled recording.
30
1) Configure All Day or Customize Record:

If you want to configure the all-day recording, please check the All Day checkbox.
If you want to record in different time sections, check the Customize checkbox. Set the Start Time
and End Time.
The time of each segment cannot be overlapped. Up to 8 segments can be configured.

2) Select a Record Type. The record type can be Continuous, Motion, Alarm, Motion & Alarm, and
Motion | Alarm.
3) Check the checkbox of Select All and click Copy to copy settings of this day to the whole week. You
can also check any of the checkboxes before the date and click Copy.
4) Click OK to save the settings and exit the Edit Schedule interface.
6. Click Advanced to configure advanced record parameters.
7. Click Save to validate the above settings.
Playback
Interface Introduction
No.
Name
Description
Channel List
Displays the list of channels and the playing status of each channel.
Playback Window
Displays the image of channel.
Play Control Bar:
Play control operations are supported.
Time Line
Displays the time bar and the records marked with different colors.
Playback Status
Displays the playback status, including channel number and playback speed.
Calendar
You can select the date to play.
Start Playback
Steps:
31
1. Click Playback on the menu bar to enter playback interface.

2. Click the camera from the device list for playback.
3. Select the date from the calendar and click Search.
4. Click the Play button to play the video file searched on the current date.
5. Use the buttons on the toolbar to operate in playback mode.
Button
/
Description
Button
Description
Play/Pause
Stop
Slow down
Speed up
Play by single frame
Capture
Stop all playback
Download
Video clip
Full Screen
Open/Close audio
Reverse play
6. You can drag the progress bar with the mouse to locate the exact playback point. You can also input the time
in the textbox
and click
button to locate the playback point.
The color of the video on the progress bar stands for the different video types.
Log
You can view and export the log files at any time, including operation, alarm, exception and information of device.
Before you start
The Log function can be realized only when the device is connected with HDD or network disk. And make sure
the HDD or network disk has been initialized for the first time to use.
Steps:
1. Click Log on the menu bar to enter the Log interface.
2. Set the log search conditions to refine your search, including the Major Type, Minor Type, Start Time and
End Time.
3. Click the Search button to start searching log files.
4. The matched log files will be displayed on the list shown below.
Up to 100 log files can be displayed on each page.

You can click the
button to save the searched log files to local directory.
32
Menu Operation
Menu Structure
The menu structure varies according to different models.
Menu
Playback
Export
Manual
HDD
Record
Camera
Configuration
Maintenance
Shutdown
Normal
Normal
Record
General
Schedule
Camera
General
System Info
Logout
Event
Event
Alarm
Advanced
Encoding
OSD
Alarm
Log
Information
Shutdown
Advanced
Image
RS-232
Import/
Export
Reboot
Holiday
PTZ
Network
Upgrade
Motion
Live View
Default
Privacy
Mask
Exceptions
Net Detect
Video
Tampering
User
HDD Detect
Tag
Manual
VQD
Smart
External File
Video Loss
VQD
VCA
The DS-7100-SH does not support Camera, PTZ, RS-232, Alarm and VCA functions, and the DS-7200HGHI-SH
does not support RS-232 and Alarm functions.
Startup and Shutdown

Proper startup and shutdown procedures are crucial to expand the service time of the DVR.
To start the DVR:
Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible
Power Supply (UPS) be used in conjunction with the device. Turn on the power switch on the rear panel; the
Power indicator LED on the front panel should be yellow.
To shut down the DVR:
Steps:
1. Enter the Shutdown menu.
Menu > Shutdown
33
2. Select the Shutdown button.

3. Click the Yes button.
4. Turn off the power switch on the rear panel when the note appears (supported by DS-7200 series and
DS-7100 series DVR).
After the device starting up, the wizard will guide you through the basic settings, including edting password, date
and time settings, network settings, HDD initializing, and recording.
Live View
Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can find problems as soon as possible.
Indicating that there is an alarm or are alarms. Alarm includes video loss, tampering, motion detection or
sensor alarm, etc.
Recording (manual record, continuous record, motion detection or alarm triggered record)
Alarm & Recording
Event/Exception (event and exception information, appears at the lower-left corner of the screen.)
Adding IP Cameras
The connection of IP cameras is not supported by the DS-7100-SH series only.

Please refer to the Specifications for the number of connectable cameras to different models.
Steps:
1.
Right-click the mouse in the live view mode to show the right-click menu.
34
The IP camera connection is not supported by DS-7100-SH series DVR.
The DS-7100-SH, DS-7200-SH, and DS-7324/7332HGHI-SH provide no Aux Monitor option.
2.
Select Add IP Camera in the pop-up menu to enter the IP Camera Management interface.
3.
The online cameras with same network segment will be displayed in the camera list. Click the
add the camera.
button to
The added camera is marked in white while the camera not added is marked in yellow.
Explanation of the icons

Icon
Explanation
Icon
Edit basic parameters of the camera
Explanation
Add the detected IP camera.
The camera is disconnected; you can click
The camera is connected.
the icon to get the exception information of

camera.
35
Delete the IP camera.
4.
Advanced settings of the camera.
To add other IP cameras:

1)
Click the Custom Adding button to pop up the Add IP Camera (Custom) interface.
2)
You can edit the IP address, protocol, management port, and other information of the IP camera to be
added.
3)
Click Add to add the camera.
4)
(For the encoders with multiple channels only) check the checkbox of Channel No. in the pop-up window,
as shown in the following figure, and click OK to finish adding.
Record
Before you start:
Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. You may refer to
the user manual for detailed information.
Purpose:
Two kinds of record types are introduced in the following section, including Instant Record and All-day Record.
And for other record types, you may refer to the user manual for detailed information.
After rebooting all the manual records enabled are canceled.
Instant Recording
On the live view window of each channel, there is a quick setting toolbar which shows on the bottom of the
window when you click on it.
Click the
icon to enable the record, and the icon turns to
then the icon turns to
. And click
icon to disable the record,
All-day Recording
Perform the following steps to set the all-day recording.
On the live view window, right lick the window and move the cursor to the Start Recording option, and select
36
Continuous Record or Motion Detection Record on your demand.
The IP camera connection is not supported by DS-7100-SH series DVR.

And click the Yes button in the popup Attention message box to confirm the settings. Then all the channels will
start to record in the selected mode.
The DS-7100-SH, DS-7200-SH, and DS-7324/7332HGHI-SH provide no Aux Monitor option.
Playback
Play back the record files of a specific channel in the live view menu.
OPTION 1:
Choose a channel under live view using the mouse and click the
button in the shortcut operation menu.
Only record files recorded during the last five minutes on this channel will be played back.
OPTION 2:
37
1. Enter the Playback menu.

Right click a channel in live view mode and select Playback from the menu.
To the DS-7200HQHI-SH, DS-7300HGHI&HQHI-SH and DS-8100HGHI&HQHI-SH series DVR, pressing

numerical buttons on the front panel will switch playback to related channels during playback process.
2. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing process.
Just check the channel or channels if you want to switch playback to another channel or execute simultaneous
playback of multiple channels.
Backup
Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or USB DVD writers.
To export recorded files:
1. Enter Video Export interface.
Choose the channel(s) you want to back up and click the Quick Export button.
2. Enter Export interface, choose backup device and click the Export button to start exporting.
38
3. Check backup result.

Choose the record file in Export interface and click
button to check it.
VCA Alarm
Purpose:
The DS-7200/7300/8100-SH series DVR can receive the VCA alarm sent by analog camera, and the VCA
detection must be enabled and configured on the camera settings interface first.
Perform the steps below to set the VCA configuration. The device can provide VCA capability of enabling linkage
actions when detecting exceptional event, such as people, vehicles and objects cross a virtual line or intrude a
pre-defined region.
The VCA settings is supported by 1 analog camera for DS-7200/7300/8100HGHI-SH models and 2 analog camers
for DS-7200/7300/8100HQHI-SH models. DS-7100-SH does not support VCA.
Steps:
1. Enter VCA Alarm interface of Camera Management and select a camera you want to detect VCA alarm.
Menu> Camera> VCA
The selected camera must support the VCA function.
2. Select the analog camera to configure the VCA.
39
3. Select the detection type to Line Crossing Detection or Intrusion Detection.

Line Crossing Detection: This function can be used for detecting people, vehicles and objects cross a set
virtual line. The line crossing direction can be set as bidirectional, from left to right or from right to left. And
you can set the duration for the alarm response actions, such as full screen monitoring, audible warning, etc.
Intrusion Detection: This function can be used for detecting whether there are people, vehicles and objects
intruding into the pre-defined region longer than the set duration. And you can set the duration for the alarm
response actions, such as full screen monitoring, audible warning.
4. Check the Enable checkbox to enable the selected VCA detection.
5. Click the
to configure the trigger channel, arming schedule and linkage actions.
6. Configure the region and other settings for the selected VCA detection.
7. Click Apply to save the settings.
Access by EZVIZ Cloud P2P

You can choose the access to the DVR by EZVIZ Cloud P2P or by DDNS through the settings on the Extranet
Access menu.
EZVIZ Cloud P2P provides the mobile phone application and as well the service platform page to access and
manage your connected DVR, which enables you to get a convenient remotely access to the surveillance system.
Steps:
1.
Enter the Network Settings interface.

Menu > Configuration > Network
2.
Select the Extranet Access tab to enter the EZVIZ Cloud P2P Settings interface.
3.
Check the Enable EZVIZ Cloud P2P checkbox to activate this feature.
4.
If required, check the Enable Stream Encryption checkbox to encrypt the video stream.
5.
Enter the verification code of the device.
The verification code consists of 6 capital letters and is located at the bottom of the device.
The device at the version 3.0.1 or above has its verification code automatically available in the field by
default; for device of older version, you need to input any 6 capital letters in the text filed.
6.
Click the Apply button to save and exit the interface.
After configuration, you can access and manage the DVR by your mobile phone on which the EZVIZ Cloud P2P
application is installed or by the EZVIZ Cloud P2P website (www.ezviz7.com).
For more operation instructions, please refer to the help file on the EZVIZ Cloud P2P official website (www.
ezviz7.com).
40
0300011040804
41
42

Quick Start Guide of TVI Series DVR DS-7100HGHI-SH

Uploaded by

Copyright:

Available Formats

Quick Start Guide of TVI Series DVR DS-7100HGHI-SH

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quick Start Guide of TVI Series DVR DS-7100HGHI-SH

Uploaded by

Copyright:

Available Formats

Digital Video Recorder

Quick Start Guide

Quick Start Guide of Digital Video Recorder

Quick Start Guide of Digital Video Recorder

Quick Start Guide of Digital Video Recorder

Trademarks and Registered Trademarks

VGA is the trademark of IBM.

Quick Start Guide of Digital Video Recorder

Use brackets for rack mounting.

Quick Start Guide of Digital Video Recorder

Hard Disk Installation

HDD Installation (A)

3. Connect the power cable to the HDD.

Quick Start Guide of Digital Video Recorder

5. Re-install the cover of the DVR and fasten screws.

HDD Installation (B)

Quick Start Guide of Digital Video Recorder

Front Panel of DS-7100HGHI-SH and DS-7104HQHI-SH

Indicator turns red when DVR is powered up.

Indicator blinks blue when network connection is functioning properly.

Front Panel of DS-7204/7208HGHI-SH

Front Panel of DS-7216HGHI-SH

Quick Start Guide of Digital Video Recorder

Front Panel of DS-7200HQHI-SH

Power indicator turns yellow when the device s running.

written to HDD, and turns yellow when the SHIFT function is

Switch between the numeric or letter input and functions of the

Enter letters DEF;

Enter letters GHI;

Delete characters before cursor;

Enter letters MNO;

Enter letters PQRS;

Quick Start Guide of Digital Video Recorder

Enter letters WXYZ;

select the next and previous record files.

In Playback mode, it can be used to play or pause the video.

Universal Serial Bus (USB) ports for additional devices such as

Front Panel of DS-7300HGHI-SH and DS-7300HQHI-SH

Quick Start Guide of Digital Video Recorder

Slot for DVD-R/W.

Enter letters DEF;

Enter letters GHI;

Delete characters before cursor;

Enter letters MNO;

Enter letters PQRS;

Enter letters TUV;

Quick Start Guide of Digital Video Recorder

alphabet, symbols or numeric input).

next and previous record files.

The ENTER button is used to confirm selection in any of the menu

In Playback mode, it can be used to play or pause the video.

Power on/off switch.

JOG SHUTTLE Control

In Live View mode, it can be used to cycle through different channels.

DS-8100HGHI-SH and DS-8100HQHI-SH

Quick Start Guide of Digital Video Recorder

Switch between different channels in Playback mode.

the next and previous record files.

In PTZ control mode, it can control the movement of the PTZ

In Playback mode, it can be used to play or pause the video.