GD&T Symbols

GEOMETRIC DIMENSIONING
SYMBOLS, RULES, AND GUIDELINES
FACTS TO REMEMBER
MMC MAXIMUM MATERIAL CONDITION:
M
THAT CONDITION WHERE A FEATURE OF
SIZE CONTAINS THE MAXIMUM AMOUNT OF
MATERIAL WITHIN THE STATED LIMITS
OF SIZE. EXAMPLE: MINIMUM HOLE SIZE
AND MAXIMUM SHAFT SIZE.
TYPE
.500
TOLERANCE
ZONE
STRAIGHTNESS
.500
.005
FORM
.500
.500
TWO CONCEN
TRIC CYLINDERS
.004 APART
.005
.004
CYLINDRICITY
TWO PARALLEL
PLANES.004
APART
.004 A
A
ORIENTATION
PARALLELISM
TWO PARAL
LEL PLANES
.004 APART
A
.004 A
PERPEN
DICULARITY
90
TWO PARALLEL
PLANES .004
APART
15
A
.004 A
DIAMETER SYMBOL: THIS SYMBOL
REPLACES THE WORD "DIAMETER." IT
SHOULD BE USED ANYWHERE THERE IS A
DIAMETER ON THE DRAWING, AND WHEN
A TOLERANCE ZONE IS CYLINDRICAL.
15
A
ANGULARITY
DATUM TARGETS: USED TO LOCATE

SPECIFIC POINTS, LINES, OR AREAS
A1
ON PARTS USED FOR SUPPORT FOR
MACHINING AND INSPECTION COMMONLY
USED ON RIGID PARTS LIKE CASTINGS AND
FORGINGS AND NON-RIGID PARTS MADE
FROM PLASTIC, RUBBER, OR SHEET METAL.
PROFILE
OF A LINE
PROFILE
OF A
SURFACE
RUNOUT
CONCENTRIC
CIRCLES
A
.004 APART
CIRCULAR
RUNOUT
.004 A
TWO CONCENTRIC
CYLINDERS
A
.004 APART
TOTAL
RUNOUT
.250
.004
B
RESTRICTED MOVEMENT
.014 ZONE
AT MMC
.380
.620
POSITION
A
.620 C
PARALLEL LINES
.005 M
TERTIARY DATUM
(ONE POINT MIN)
SECONDARY DATUM
(TWO POINTS MIN)
MODIFIER FOR THE

STATED TOLERANCE
NO
NO
NO
DOES
NOT
APPLY
NO
NO
STATED TOLERANCE
M OR
M OR
YES
IF
G
H
YES
IF
YES
J
A
D
IS
STATED
YES
IF
YES
IS
STATED
NO
DOES
NOT
APPLY
MAY BE
USED
OR
MAY NOT
NO
RFS
ALWAYS
YES
NO
RFS
ALWAYS
YES
NO
YES
IF
IS
STATED
D
E
F
YES
EXAMPLE:
.500
.507
.005 M
MAY BE
USED
OR
MAY NOT
CAN
APPLY
TO A
FEATURE
OF SIZE.
BONUS TOLERANCE: WHEN MMC IS

SHOWN MODIFYING A PARTICULAR
TOLERANCE, THE STATED TOLERANCE
APPLIES ONLY WHEN THE FEATURE BEING
CONTROLLED IS AT MMC. THE BONUS IS
THE DIFFERENCE BETWEEN THE ACTUAL SIZE
AND THE MMC SIZE AND MAY BE ADDED
DIRECTLY TO THE ORIGINAL TOLERANCE.
DOES
NOT
APPLY
M OR
RELATIVE TO
CAN
APPLY
TO A
FEATURE
OF SIZE.
A B C
WITHIN
EXAMPLE: THE POSITION OF THE

FEATURE AXIS MUST BE WITHIN A .005
TOLERANCE ZONE AT MMC RELATIVE TO
DATUM FEATURES A, B, AND C.
IS
STATED
YES
CAN
APPLY
TO A
FEATURE
OF SIZE.
BASIC SENTENCE STRUCTURE: WHEN

USING THE ENGLISH LANGUAGE TO SAY
WHAT IS IN THE FEATURE CONTROL FRAME.
YOU MAY USE THE FOLLOWING CONNECTING
WORDS:
.005 M
ACTUAL
MMC
.503
.500
BONUS
.003
AT MMC THE HOLE MUST BE POSITIONED

WITHIN A CYLINDRICAL TOLERANCE ZONE OF
.005 DIAMETER. AS THE EXAMPLE SHOWS,
THE HOLE HAS DEPARTED FROM MMC BY
.003. THE .003 BONUS TOLERANCE MAY
NOW BE ADDED TO THE ORIGINAL .005
ZONE FOR A TOTAL OF .008 TOLERANCE.
FUNCTIONAL GAGES: DEVICES THAT
MEASURE THE COLLECTIVE EFFECTS OF SIZE
AND GEOMETRIC TOLERANCES AT THE SAME
TIME. IT REPRESENTS A SIMULATED
MATING CONDITION.
BONUS TOLERANCES AND FUNCTIONAL
GAGES: DIRECTLY APPLICABLE TO ANY
GEOMETRIC CHARACTERISTIC THAT IS
MODIFIED BY M .
SHIFT: AS A DATUM FEATURE OF SIZE,
THAT IS GEOMETRICALLY CONTROLLED,
DEPARTS FROM MMC, ADDITIONAL
TOLERANCE MAY BE CONSIDERED FOR THE
CONTROLLED FEATURES. THIS ADDITIONAL
TOLERANCE DOES NOT ADD DIRECTLY TO
THE ORIGINAL TOLERANCE BUT MUST BE
APPLIED TO THE PATTERN OF FEATURES AS A
GROUP. IT IS CONSIDERED A TOLERANCE
THAT ALLOWS THE CONTROLLED FEATURES
TO SHIFT AS A GROUP.
VIRTUAL CONDITION: THE COLLECTIVE
EFFECT OF SIZE AND GEOMETRIC
TOLERANCES THAT MUST BE CONSIDERED
IN DETERMINING THE FIT OR CLEARANCE
BETWEEN MATING PARTS OR FEATURES.
TO CALCULATE VIRTUAL CONDITION:
EXTERNAL FEATURES:
MMC SIZE + TOLERANCE OF FORM,
ORIENTATION, OR LOCATION
INTERNAL FEATURES:
MMC SIZE TOLERANCE OF FORM,
ORIENTATION, OR LOCATION
.004 AROUND
DATUM AXIS
.004 A
A VIRTUAL CONDITION WILL EXIST ONLY FOR

TOLERANCES THAT CONTROL SIZE FEATURES.
A
CONCEN
TRICITY
RFS
ALWAYS
YES
NO
RFS
ALWAYS
YES
NO
PARALLEL PLANES
THIS CHART IS PROVIDED FOR

INFORMATIONAL PURPOSES ONLY.
THE INFORMATION IS BASED UPON
ASME Y14.5M - 1994.
G
H
GENIUM PUBLISHING CORP.

ONE GENIUM PLAZA
SCHENECTADY, NY 12304
(518) 377-8854
.004 EQUALLY
DISPOSED FROM
CENTER PLANE
.004 A
PARALLEL LINES
* THIS COLUMN INDICATES POSSIBLE

TOLERANCE ZONES THAT MAY BE USED WITH
THE VARIOUS CONTROLS. THE DIFFERENT
TOLERANCE ZONES ARE SHOWN ALONG THE
BOTTOM OF THIS CHART.
SYMMETRY
A B C
PRIMARY DATUM
(THREE POINTS MIN)
.380
PARALLEL LINES
PITCH DIAMETER RULE: TOLERANCES

THAT APPLY TO SCREW THREADS APPLY TO
THE AXIS OF THE THREAD DERIVED FROM
THE PITCH CYLINDER. IF ANOTHER PART OF
THREAD IS TO BE USED TO DERIVE THE
AXIS, IT MUST BE STATED BENEATH THE
FEATURE CONTROL FRAME. ANY OTHER
FEATURE THAT HAS A PITCH DIAMETER MUST
HAVE THE DATUM FEATURE STATED.
IS
STATED
FEATURE CONTROL FRAME:
TRUE CENTER
LOCATION
GEOMETRIC TOLERANCE RULE: GEOMETRIC

TOLERANCES ARE UNDERSTOOD TO BE
APPLIED RFS. IF MMC OR LMC IS
REQUIRED, IT MUST BE PLACED IN THE
FEATURE CONTROL FRAME. SEE MMC, LMC,
OR RFS COLUMN.
.022 ZONE
AT LMC
.014 M A B C
FREE MOVEMENT
LIMITS OF SIZE RULE: WHERE ONLY A

SIZE DIMENSION IS GIVEN. a) THE SIZE
DIMENSIONS AT ANY CROSS SECTION MUST
BE WITHIN THE SIZE TOLERANCE. b) THE
SURFACE(S) SHALL NOT EXTEND BEYOND
THE PERFECT FORM DEFINED BY THE MMC
SIZE. c) THE FORM MAY VARY WITHIN AN
ENVELOPE BETWEEN THE MMC AND LMC.
NO
NO
CAN
APPLY
TO A
FEATURE
OF SIZE.
TWO PLANES
.004 APART
ALONG TRUE
PROFILE
A
.004 A
.004 A
DATUM REFERENCE FRAME: (THREE PLANE
CONCEPT). THE CONCEPT OF USING
MUTUALLY PERPENDICULAR FEATURES OF A
PART TO CONTROL ITS FREE MOVEMENT IN
SPACE (DEGREES OF FREEDOM). SEE DATUM
SYMBOL AND DATUM TARGETS.
DOES
NOT
APPLY
M OR
TWO LINES
.004 APART
ALONG TRUE
PROFILE
.004
PROFILE
TOLERANCE ZONES: ALL TOLERANCE

ZONES SHOWN IN THE FEATURE CONTROL
FRAME ARE TOTAL. EXAMPLE: FLATNESS
WITHIN .004 MEANS THAT TWO PARALLEL
PLANES NO MORE THAN .004 APART
DEFINE THE TOLERANCE ZONE.
YES
IF
GEOMETRIC CHARACTERISTIC SYMBOL
TWO CONCEN
TRIC CIRCLES
.004 APART
.005
.004
FREE STATE: THIS SYMBOL INDICATES

F
THE PARTS MUST NOT BE RESTRICTED
DURING INSPECTION.
TOLER
ZONE
TYPE
DIAMETER SYMBOL (CYLINDRICAL

TOLERANCE ZONE)
CIRCULARITY
ST STATISTICAL TOLERANCE: A
TOLERANCE FOR A PART OF AN
ASSEMBLY BASED ON THE RESULTS FROM
A STATISTICAL CALCULATION. THE DESIRED
RESULT IS LARGER TOLERANCES.
BASIC DIMENSION: THESE

DIMENSIONS HAVE NO TOLERANCE.
THEY ONLY LOCATE A TOLERANCE ZONE.
DOES
NOT
APPLY
FACTS TO REMEMBER
FUNC
GAGE
USED
DATUM
USED
CAN
APPLY
TO A
FEATURE
OF SIZE.
TWO PARALLEL
PLANES, .004
APART
.004
PROJECTED TOLERANCE ZONE: WHEN

THE SYMBOL IS SHOWN, IT MEANS THE
STATED TOLERANCE ZONE IS EXTENDED
BEYOND THE SURFACE OF THE PART, NOT
WITHIN THE PART.
DATUM SYMBOL: THIS SYMBOL IS

ATTACHED TO A PLANE OR SIZE
FEATURE THAT MUST BE CONTACTED
FOR MACHINING AND INSPECTION.
M OR
FLATNESS
MMC LMC
OR RFS
TWO PARALLEL
LINES .004
APART
.005
.004
LMC LEAST MATERIAL CONDITION:

L
THAT CONDITION WHERE A FEATURE OF
SIZE CONTAINS THE LEAST AMOUNT OF
MATERIAL WITHIN THE STATED LIMITS
OF SIZE. EXAMPLE: MAXIMUM HOLE SIZE
AND MINIMUM SHAFT SIZE.
RFS REGARDLESS OF FEATURE SIZE:
THIS IS THE DEFAULT CONDITION FOR ALL
GEOMETRIC TOLERANCES. NO BONUS
TOLERANCES ARE ALLOWED. FUNCTIONAL
GAGES MAY NOT BE USED.
AS SHOWN
ON DRAWING
SYMBOL
PARALLEL PLANES
PARALLEL PLANES
PARALLEL PLANES
PARALLEL PLANES
CYLINDER ZONE

GD&T Symbols

Uploaded by

Copyright:

Available Formats

GD&T Symbols

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GD&T Symbols

Uploaded by

Copyright:

Available Formats

GEOMETRIC DIMENSIONING

SYMBOLS, RULES, AND GUIDELINES

DATUM TARGETS: USED TO LOCATE

MODIFIER FOR THE

BONUS TOLERANCE: WHEN MMC IS

EXAMPLE: THE POSITION OF THE

BASIC SENTENCE STRUCTURE: WHEN

AT MMC THE HOLE MUST BE POSITIONED

A VIRTUAL CONDITION WILL EXIST ONLY FOR

THIS CHART IS PROVIDED FOR

GENIUM PUBLISHING CORP.

* THIS COLUMN INDICATES POSSIBLE

PITCH DIAMETER RULE: TOLERANCES

FEATURE CONTROL FRAME:

GEOMETRIC TOLERANCE RULE: GEOMETRIC

LIMITS OF SIZE RULE: WHERE ONLY A

TOLERANCE ZONES: ALL TOLERANCE

GEOMETRIC CHARACTERISTIC SYMBOL

FREE STATE: THIS SYMBOL INDICATES

DIAMETER SYMBOL (CYLINDRICAL

BASIC DIMENSION: THESE

PROJECTED TOLERANCE ZONE: WHEN

DATUM SYMBOL: THIS SYMBOL IS

LMC LEAST MATERIAL CONDITION:

You might also like