Process of Press Tool Design and Its Manufacturing For Blanking Operation

ISSN(Online) : 2319-8753
ISSN (Print) : 2347-6710
International Journal of Innovative Research in Science,

Engineering and Technology
(An ISO 3297: 2007 Certified Organization)
Vol. 5, Issue 5, May 2016
Process of Press Tool Design and its

Manufacturing for Blanking Operation
Subramanyam Pavuluri1, B.Rajashekar2, B.Damodhar3
Assistant Professor, Department of Mechanical Engineering, MLR Institute of Technology, Dundigal, Hyderabad,
Telangana, India21
U.G. Student, Department of Mechanical Engineering, MLR Institute of Technology, Dundigal, Hyderabad, Telangana,
India2&3
ABSTRACT: Press tools are used to produce a particular component in large quantity, out of sheet metals where
particular component achieved depends upon press tool construction and its configuration. The different types of press
tool constructions leads to different operations namely blanking, bending, piercing, forming, drawing, cutting off,
parting off, embossing, coining, notching, shaving, lancing, dinking, perforating, trimming, curling etc. Generally
metals having thickness less than 6mm is considered as strip. Blanking is one of the sheet metal operations where we
produce flat components of prerequisite shape. In Blanking the required shape periphery is cut and cut-out piece is
called blank. The press tool used is for blanking operation is called as blanking tool, if piercing operation it is piercing
tool and so on based on operation that we perform. The application of press operations are widely used in many
industries like food processing, packing, defence, textile, automobile, aircraft and many apart from manufacturing
industry. In this connection an attempt is made on to learn the press tool design, materials, manufacturing used for press
tool and calculations involved in it. In this work, a real time design of a simple blanking press tool and manufacturing
of a prototype is made along with analysis where the output is a circular piece having diameter of 20mm. The press
machine is of mechanical type.
KEYWORDS: Blanking, Die Design, Manufacturing, and Analysis;
I. INTRODUCTION
High rate production industries generally use press machines. Thickness can vary significantly, although extremely
small thicknesses are considered as sheet and above 6mm are considered as plate. Thickness of the sheet metal fed in
between is called its gauge. Sheet metal is simply fed in between the dies of press tool for any press operation to
perform. The reciprocating movement of punch is caused due to the ram movement of press machine. The press
machine may be of electrical type, mechanical type, pneumatic type, manual type and hydraulic type. In todays
practical and cost conscious world, sheet metal parts have already replaced many expensive cast, forged and machined
products. The common sheet metal forming products are metal desks, file cabinets, appliances, car bodies, aircraft
fuselages, mechanical toys and beverage cans and many more. Due to its low cost and generally good strength and
formability characteristics, low carbon steel is the most commonly used sheet metal because high carbon composition
gives high strength to the material. The other sheet metals used are aluminium and titanium in aircraft and aerospace
applications.
The purpose of this paper is to examine the causes for these seemingly contradictory results. An attempt will be made
here to review the previous studies to look into future possibilities of various die designs. The various authors
considerations are taken into account with their presents in building up the work and their statements are as follows:
Mr. Amit D. Madake et.al.[1] He states that sheet-metal die is an inseparable constituent of the development process of
any given automotive or consumer appliance. In most of the cases, this accounts for a high proportion in the tooling
needs of the large size and structural member in any automotive like the chassis and the BIW.
Copyright to IJIRSET
DOI:10.15680/IJIRSET.2016.0505285
8602
ISSN (Print) : 2347-6710

K.Kishore Kumar et.al.[2] explains that before converting raw materials to a finished product we need an accurate
design of the product and also data required for manufacturing. If the design is not accurate then defects will occur in
the manufactured product, small mistakes in designing a product makes the manufactured product useless so more
amount time is allotted for designing new product. Gasper Gantar et.al.[3] states that the selection of most appropriate
design and technological solutions to produce certain mould should capture technical performance economical issues as
well as environmental impacts occurred during the mould life cycle. An approach is presented to support the selection
of alternative mould design solutions in the early design stage. Sachin Ramdas Jadhav et.al.[4] He explains sheet metal
forming problems are typical in nature since they involve geometry, boundary and material non-linearity. Drawings
part involves many parameters like punch and dies radius, clearance, lubrication, blank holding force and its
trajectories etc. So designing the tools for part drawing involves a lot of trial and error procedure.
Vishwanath M.C. et.al.[5] He states that in this work the use of a software namely Pro/E for designing a progressive
die to manufacture cup for the oil filter has been incorporated. A progressive die is a multiple station die. In this work
authors have designed a progressive die which has two stages of operation. The former operation is piercing and is
followed by blanking.
T. Z. Quazi et.al.[6] prescribes a model investigation the effect of potential parameters influencing the blanking
process and their interaction. The blanking process optimization carried out by using Design of Experiment (DOE),
Finite Element Method (FEM) with ANSYS Package, Simulation with ABAQUS-Explicit software, Blank soft
Software and Neural Network Amol Totre et.al.[7] refers about forming processes employed in high volume production,
blanking is one of the most widely used separation techniques. Still, analysis of blanking is mainly based on
phenomenological knowledge.
Samadhan D. Bhosale et.al.[8] His aim is to apply the quality tools to find out the root causes of the quality problems
related to manufacturing of mechanical seal. The modes of defects on production line are investigated through direct
observation on the production line and statistical tools like Check sheets, Histogram, Pareto analysis, Cause and Effect
diagram etc are used in enhancing the process by continuous monitoring through inspection of the samples.
Jai Hindus S et. al.[9] He assists the die designer to design press tool dies for the online maintenance in the press itself
and to reduce the tool failure due to the dynamic actions of the press tool in the press.
The press machines may be of 1 ton, 2ton, 3ton etc. based on the amount of tonnage acting on the sheet. For general
specifications and diagram of press machine see Fig: 1 and Table.1 shown below:
Table.1 Specifications of 10 ton Press Tool Machine
SPECIFICATIONS
10 ton
Bed Size LR x FB(mm)

Bed to ram bottom(mm)
Bed to ram bottom(mm)
Adjustment of slide(mm)
Bloster thickness(mm)
Bed opening(mm)
Shank hole dia
No of strokes per min(mm)
No of strokes per min(S.P.M)
Motor power(H.p/R.P.M)
482x318
243
51
25
67
100
32
735
55
1.5/1440
Fig: 1 Mechanical Press Tool Machine
DOI:10.15680/IJIRSET.2016.0505285
8603
ISSN (Print) : 2347-6710

Before design of tool it is necessary to understand the configuration of it and its components of press tool are in Fig: 2
The press tool consist of the punch , the die holder are used for fixing the die to the press machine. Die holder also used
for supporting the rigidity of the die and its main function is to hold the punch. Backing plates are used at three
locations in a die basically. It prevent the components to go deep inside the holder due to the force of press operation.
Fig: 2 Principle of Press Tool Die

Backing plates are also used for preventing the parts from getting detached and for adjusting the height of the die. A
punch plate is used for the purpose of holding the punch during press operation. The main function of a stripper is to
remove scrap, very frequently it is made to have important secondary functions of guiding the tip of the punch during
press operation . Die plate determines the output of the press function and also the cutting is of sheet is done . For
proper function clearance is left between the punch and die plate where the clearance depends on the sheet metal
thickness and the type of material. The materials used for punches are powered high speed tool steel and punch
dimensions determines the output of the press function. This paper is presenting the key factors and procedure involved
in the manufacturing of blanking press tool and the procedure is below.
II. METHODOLOGY
(a) SELECTION OF MATERIALS
Press tools are generally made using HCHCr, Steel alloys with high carbon. But before that based on many factors like
cost, strength, hardness, strain and many parameters selection should be made. The materials used are generally
selected are D2,EN31.Mild Steel is used as supporting plate. Apart from that materials like D3, high carbide materials,
chromium steels and high speed steels are also used. The properties of the materials used in the experimentation are
tabulated below:
(i) En31: EN31 is a high carbon Alloy steel which achieves a high degree of hardness with compressive strength
and abrasion resistance that are acceptable for many automobile applications such as heavy duty gear,
shaft, pinion, cam shafts. It is neither externally brittle nor ductile due to its lower carbon content and
lower hardness. For properities of En31 shown in Table No.2, 3 and 4
(ii)
Table.2 Properties of En31
Table.3 Physical properties
Chemical Composition (%)
Melting
Density
Carb
Silic
phosphor
point
Manganese
sulphur
0
on
on
ous
1421 C
7.7 x 1000 kg/m3
0.18
0.35
1
0.05
0.05
DOI:10.15680/IJIRSET.2016.0505285
8604
ISSN (Print) : 2347-6710

Table.4 Mechanical Properties and Thermal properties

Rockwell
Izod
Thermal
Elastic modulus
hardness
impact
properties
Thermal expansion
190- 210 GPa.
62
77.0 J
10.4 x10-6 / C
(ii) D2 STEEL: This alloy is one of the Cold Work, high carbon, high chromium type tool steels. D2 is a deep
hardening, highly wear resistant alloy. It hardens upon air cooling so as to have minimum distortion after heat treatment.
Used for long run tooling applications where wear resistance is important, such as blanking or forming dies and thread
rolling dies. For properties of D2 steel as shown in Table.5 and 6
Carbon
1.6
Silicon
0.6
Manganese
0.6
Table.5 Chemical composition

Chemical Composition (%)
Chromium Sulphur Phosphorus
13
0.03
0.033
Vanadium
1.1
Molybdenum
1.2
Table.6 Physical properties and Mechanical properties

Rockwell
Tensile
Melting
Density
Elastic modulus
Yield stress
hardness
strength
point
7810 kg/m3
65
215000N/ mm2
450N/ mm2
750N/ mm2
15400C
After material selection is done we have to design the press tool according to the calculations shown below.
III. MODELLING
The materials used for making above blocks are mild steel and HCHCr. The material for the punch and the die block is
HCHCr (EN31 and P20) whereas for base plate and guide block it is mild steel (H13 and EN8) . Punch and Die block
should have high strength compared to base plate and Guide block. So high strength materials are used for punch and
base. By comparison on many factors like strength ability, Machinability, thermal properties, load factor and cost factor
EN31 and EN8 suits best. So EN31 selected for punch and base, EN31 for die and guide block.
a) Punch and Die Block
The main function of the punch is to strike the sheet metal, which is attached to the hub of the power press machine.
The striking power is dependent on tons capacity of machine. The punch is fitted by means of tapering at its top locked
by a nut. The dimensions of punch are and its drawing in AUTOCAD 2014 as shown in below drawings. The shape
and dimensions of the product to be achieved depends on design of Die block. The product is of coin type shape with
20mm dia. Clearance should be there between punch and Die block, otherwise we cannot perform the operation.
Clearance is given based on the thickness of sheet and it is about 10% of sheet thickness. If we consider sheet thickness
as 2mm then positive tolerance should be given as 0.2mm for die block.
Fig: 3 Punch
Fig: 4 Die Block
DOI:10.15680/IJIRSET.2016.0505285
8605
ISSN (Print) : 2347-6710

b) Guide Block and Base Plate

The Guide block is just a supportive block that acts as intermediate between the punch and the Die block. The main
function is to oppose the Shear force and perform sheet metal operation. The drawing and dimensions is shown in Fig:5
for the guide block. The Base plate or bottom plate is placed at the end of the configuration where the work piece or
scrap goes down. Here the punch moves down with high force, so in order to prevent the breakage of Die high strength
material is used and placed as bottom plate. So base plate and punch are made of same material. The diagram and
dimension for Base plate is shown in Fig: 6 below:
Fig: 5 Guide Block
Fig: 6 Base Plate
c) ASSEMBLY
The assembly of all four parts including the screwing is shown below with front and top view:
Fig: 7 Assembly Diagram
DOI:10.15680/IJIRSET.2016.0505285
8606
ISSN (Print) : 2347-6710

DESIGN CALCULATIONS
The strip layout is presented in Fig:8. The calculation is done on strip to find out the following steps
% of strip used =(Area of component x 4)/Lenh of strip x width of strip
Shear force = (KxLxTxS)/1000tons)= (1.5x2x3.141x10x0.5x420)/1000 =1.97 tons
Where, K =1.1 to 1.5 (constant based on clearance), L= length of cut in mm, T= thickness of cut in mm
S= Shear strength of material in kg/mm2
Stripping force = 10%of shear force = 0.2 ton
Net force = Shear force+ Stripping force = 1.97+0.2 =2.2 ton
Fig: 8 Strips
Fig: 9 Blank
The shear force, stripping force, net force and their respected values are as follows 1.97, 0.2, 2.2tons
The blank is shown in Fig: 9 and the calculations for it is done as follows
Press tonnage = 1.2 x Total force = 1.2 x 2.2 = 2.64 tons
Thickness of die plate = 3Fsh = 4.2mm
Thickness of punch holder = 0.5 x td =0.5x5 = 2.5mm (td = thickness of plate selected)
Similarly by substitution td values we get
Thickness of bottom plate = 1.5 x td = 7.5mm
Thickness of top plate = 1.25 x td= 6.25mm
Thickness of stripper plate = 0.5 x td= 2.5mm
Cutting clearance = C x S x (TMax)/10 = 0.05mm
C=0.01-0.005(for accurate)
S= Sheet metal thickness, Tmax= Based on material property (Max Stress bearable)=1000 N/mm2
(Or)
Cutting clearance = 4% of sheet thickness
Black punch size = Size of Blank die-2c
C=6% of thickness of wall
Cutting force = x D x t x Fs =3.14x0.5x20x2.2= 69 N
Based on the output product required the calculations are made and proceeded to manufacture. Before we perform
machining operations the material is already heat treated in order to achieve soft material. For D2 material to become
soft material Annealing should be done. In annealing process (1550-16000F) is heated and slowly cooled to about
10000F. Now machining operations should be performed except finishing process. After machining Quenching (1500F
cooled), Tempering(9500F), Hardened to (1800-18500F) to obtain hardened material. Then only finishing operations are
to be done to achieve the tool. Machining operations include lathe operation and milling operation on CNC (Computer
Numerical Control). The operations done on lathe are facing and turning. Apart from that we also used drilling machine
DOI:10.15680/IJIRSET.2016.0505285
8607
ISSN (Print) : 2347-6710

for the drilling of holes and tapping operation is also performed. Milling operation is performed in CNC and its
program is below:
N10 G00 G90 X70 Y25;
Z1 S800 M3
N20 Z-5;
N30 G01 X20 F150;
N40 G00 Z100;
N50 X25 Y50;
N60 M30;
IV. ANALYSIS FOR PUNCH
Press Tool Efficiency
Press tool efficiency is lost through defects accumulating in press components. As the die significantly impact the
overall efficiency of the press, defects the efficiency of the press tool. When defects arise, such as punch cracking and
die corrosion leads to inefficient interactions between the punch and the die which increases the damage of the press
tool ultimately reflects increase in the costs. Hence, to avoid, or at least diminish, elevated energy costs, the
implementation of an improved press tool design, consistent with the findings of this paper, should be considered.
Meshing is shown in Fig: 10
Fig: 10 MESH
Fig: 11 Vonmises Stress
Stress analysis enables the designer to efficiently validate quality, safety, performance of the designed product. In fig:
11, 12 and 13
Fig: 12 Static Displacement
Fig: 13 Strain
DOI:10.15680/IJIRSET.2016.0505285
8608
ISSN (Print) : 2347-6710

By using the SOLID WORKS software the analysis is performed. In this software itself gets own parameters if we
input the pressure value, selection of material. The result is:
The part deforms in displacements
The product is static and constant over time
The constant stress strain relationship in material.
V. CONCLUSIONS
Design of press tool for blanks made for sheet metal component has been developed by following the fundamental die
design principles. The press tonnage required for the operation is below the capacity of the machine which exists. So it
is suitable for its preceding press ton machine. Moreover the geometrical compatibility of the mechanical press and the
designed combined press tool is excellent. The output received is
Output product having diameter 20mm and its tonnage capacity is 2.2 tons. So it suits for above 2.5 ton press
machines.
The tools generally made from steel alloys. Based on carbon composition they are classified in P type, D type, H type.
of all D type is having more carbon percentage which indirectly posses more strength. They are mainly used for making
of tools.
The stress region in punch and strain displacement is found.
Therefore newly developed combined press tool is recommended in order to have an improved productivity, improved
efficiency, better flexibility, more economical manufacturing process with lower cost of the product.
REFERENCES
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
Mr.Amit ,D.Madake, Dr.Vinayak, R.Naik, Mr.Swapnil, S.Kulkarni, "Development of a SheetMetal Component with a Forming Die Using
CAE Software Tools (Hyper form) For Design Validation and Improvement", International Journal of Modern Engineering Research
(IJMER) , Volume 3, Issue 3, May-June, 2013 , pp-1787-1791,ISSN: 2249-6645.
K.Kishore Kumar, Dr. A.Srinath, M.Naveen, R.D.pavan kumar, "Design of progressive dies", International Journal of Engineering Research
and Applications (IJERA), ISSN: 2248-9622, Volume 2, Issue 3, May-Jun 2012, pp.2971-2973.
Gasper Gantar, Andrej Glojek, Mitja Mori-BlazNardin, MihaelSekavcnik, "Resource Efficient Injection Moulding with Low Environmental
Impacts", Strojniski Vestnik-Journal of Mechanical Engineering, 59(2013)3,copy right 2013,Journal of Mechanical Engineering, All rights
reserved.DOI:10.5545/sv-jme.2012.661 pp:193-200.
Sachin Ramdas Jadhav, Sunil Hiraman More, Swapnil S. Kulkarni," Die Design for Formed Component using inputs from FEA for
determining the most suited values for the Design or Process parameter", International Journal of Advanced Engineering Research and Studies
E-ISSN22498974 /April-June,2014/95-98.
Vishwanath M.C, Dr. Ramni, Sampath Kumar L ,"Design of progressive draw tool", International Journal of Scientific and Research
Publications, Volume 3, Issue 8, August 2013 ,1 ISSN 2250-3153.
Prof. T. Z. Quazi, R.S.Shaikh, "An Overview of Clearance Optimization in Sheet Metal Blanking Process", International Journal of Modern
Engineering Research (IJMER) Volume 2, Issue.6, Nov-Dec 2012, pp-4547-4558 ISSN: 2249-6645.
Amol Totre, Rahul Nishad , Sagar Bodke, An Overview Of Factors Affecting In Blanking Processes" International Journal of Emerging
Technology and Advanced Engineering, (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 3, Issue 3, March 2013).
Samadhan D. Bhosale, S.C.Shilwant, S.R. Patil ," Quality improvement in manufacturing processes using SQC tools" International Journal of
Engineering Research and Applications (IJERA), ISSN: 2248-9622 Vol. 3, Issue 3, May-Jun 2013, pp.832-837.
Jai hindus S."Design and development of stamping dies for online maintenance" Vol. 9, No. 4, APRIL 2014, ISSN 1819-6608,ARPN Journal
of Engineering and Applied Sciences,2006-2014, Asian Research Publishing Network (ARPN), All rights reserved.
Hairulliza Mohamad Judi, Ruzzakiah Jenal and Devendran Genasan "Quality Control Implementation in Manufacturing Companies
Motivating Factors and Challenges" ISBN: 978-953-307-236-4, (2011).
Dr. Taylan Altan, Selection of die materials and surface treatments for increasing die life in hot and warm forging" Paper no 644-FIA Tech
Conference, April 2011.
Hakim S. Sultan Aljibori, Abdel Magid Hamouda Finite Element Analysis of Sheet Metal Forming Process" European Journal of Scientific
Research. ISSN 1450-216X Vol.33 No.1 (2009), pp.57-69 Euro Journals Publishing, Inc. 2009.
Parikshit K patel, Prof. Vidya Nair, Ashish Patel, PFMEA(Product failure model effect analysis) of Air duct and Manufacturing process to
improve product quality, International Journal of Engineering and technology and Advanced Engineering(ISSN 2250-2459,ISO 9001:2008
Certified Journal, Vol 3, Issue 5, May 2013) pp:645-653.
DOI:10.15680/IJIRSET.2016.0505285
8609

Process of Press Tool Design and Its Manufacturing For Blanking Operation

Uploaded by

Copyright:

Available Formats

Process of Press Tool Design and Its Manufacturing For Blanking Operation

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Process of Press Tool Design and Its Manufacturing For Blanking Operation

Uploaded by

Copyright:

Available Formats

ISSN(Online) : 2319-8753

ISSN (Print) : 2347-6710

International Journal of Innovative Research in Science,

Vol. 5, Issue 5, May 2016